Construction Documentation

ATLANTIC AVE RESTAURANT 525 ATLANTIC AVE BROOKLYN NY

CLASS: DESIGNER:

PRATT INSTITUTE - INTERIOR DESIGN - INT 724 Han Xiao

FINAL SUBMISSION 05/09/19

PROJECT TEAM:

ABBREVIATIONS

MANUFACTURER MARBLE MASONRY MATERIAL MASONRY OPENING MAXIMUM MECHANICAL MEMBRANE METAL, METALLIC MEZZANINE MINIMUM MISCELLANEOUS MODULAR MOISTURE RESIST MOUNT(ED), (ING) MOVABLE MULLION NATURAL NOMINAL NON-SLIP NON APPLICABLE NOT IN CONTACT NOT TO SCALE NUMBER ON CENTER OPENING OPPOSITE OUTSIDE DIAMETER OVERHEAD PAINT PAIR PANEL PARTITION PEDESTAL PERFORATE(D) PLASTIC LAMINANT PLASTER PLATE PLUMBING PLYWOOD POINT POUND PRECAST CONCRETE PREFABRICATE(D) PROJECTED PAINTED RECESS(ED) REFERENCE REINFORCE(ED), (ING) REQUIRED RESILIANT, RESISTANT REVISION(S), REVISED RISER, RADIUS ROOF ROOF DRAIN ROOFING ROOM ROUGH OPENING ROUND RUBBER BASE SCHEDULE SCREEN SEALANT SECTION SHEET SIDING SIMILAR SKETCH SOLID CORE WOOD SPECIFICATION(S) SPRINKLER STAINLESS STEEL STATION STEEL STORAGE STRUCTURAL SURFACE SUSPENDED SYMMETRY, (ICAL) TERRA COTTA TELEPHONE TERRACOTTA THICK TO BE DETERMINED TOP OF STEEL, SLAB TOP OF WALL THREAD TYPICAL UNLESS OTHERWISE NOTED VAPOR BARRIER VINYL COMPOSITION TILE VENTILATION, VENTILATOR VERIFY IN FIELD VERTICAL VESTIBULE VINYL VINYL TILE WATER PROOF WEATHER STRIPPING WINDOW WITH WITHOUT WOOD

To the best of my knowledge, belief and professional judgment, this application is in compliance with the ECCNYS 2010

1.

2.

Energy Code Notes 2 1/4" = 1'-0"

3.

ENERGY CODE PROGRESS INSPECTION PROGRESS INSPECTIONS

4.

TABLE REFERENCE IN 1RCNY §5000-01(H) (1) AND (2)

Y N

5.

PROTECTION OF FOUNDATION INSULATION INSULATION PLACEMENT AND R VALUES FENESTRATION THERMAL VALUES AND RATINGS FENESTRATION RATINGS FOR AIR LEAKAGE FENESTRATION AREAS AIR SEALING AND INSULATION - VISUAL PROJECTION FACTORS LOADING DOCK WEATHER SEALS VESTIBULES

(IIA1) (IIA2) (IIA3) (IIA4) (IIA5) (IIA6) (IIA7) (IIA8) (IIA9)

FIREPLACES DAMPERS INTEGRAL TO BUILDING ENVELOPE HVAC AND SERVICE WATER HEATING EQUIPMENT HVAC AND SERVICE WATER HEATING SYSTEMS CONTROLS DUCT PLENUM AND PIPING INSULATION AND SEALING DUCT LEAKAGE TESTING

(IIB1) (IIB2) (IIB3) (IIB4) (IIB5) (IIB6)

ELECTRICAL METERING LIGHTING IN DWELLING UNITS INTERIOR LIGHTING POWER EXTERIOR LIGHTING POWER LIGHTING CONTROLS EXIT SIGNS TANDEM WIRING ELECTRICAL MOTORS

(IIC1) (IIC2) (IIC3) (IIC4) (IIC5) (IIC6) (IIC7) (IIC8)

MAINTENANCE INFORMATION

(IID1)

6.

7.

8.

9.

10.

11.

12.

13.

14.

INTERIOR DESIGNER NAME ADDRESS 1 ADDRESS 2 T: xxx.xxx.xxxx; F: xxx.xxx.xxxx

Smoke/Carbon Monoxide detectors or devices shall be installed in ordinance with the Housing Maintenance Code, Multiple Dwelling Law, the New York City Building Code, the New York City Electrical Code and NFPA 72.

Smoke Detectors and Carbon Monoxide Detectors may be combined providing the devices comply with the provisions of title 28 of the administrative code of the city of New York and any applicable rules promulgated thereunder.

Each Smoke/Carbon Monoxide Detector shall be installed in accordance with Reference Standard UL 2034 and UL 2075 of the New York City Building Code.

Each Smoke/Carbon Monoxide Detector shall be installed outside of each sleeping room in the immediate vicinity or within 15’-0” of the entrance to a sleeping room; inside each sleeping room; and on each story within a dwelling unit, including below grade stories and penthouses per 908.7.1.1.1 Each Smoke/Carbon Monoxide Detector shall be of a type that allows for readily testing of such device.

Duplex units shall have a device located on each level if only one means of egress is provided from each level.

Ceiling mounted devices shall be a minimum distance of 4” from any wall.

Wall mounted devices shall be a minimum of 4” to a maximum of 12” from the ceiling.

Each dwelling unit shall be equipped with an approved type smoke/carbon monoxide detector device receiving primary power from the building wiring with no switches in the circuit other than the over current device protecting the branch circuit as per New York City Building Code Sec. 907.2.10.2 through 907.2.10.4.

Existing buildings that are not equipped with hardwired connections shall be supplied with battery operated devices.

Such smoke/carbon monoxide detector must be either the ionization chamber type or the photoelectric detector type as per New York City Building Code Sec. 907 and 908.

A “Certificate of Satisfactory Installation for Smoke/Carbon Monoxide Detectors” must be filed with the division of code enforcement H.P.D., 10 days after installation.

Written information of testing and maintenance of the devices shall be provided to the dwelling unit owner.

In multiple dwellings (R-2), smoke alarms shall be able to support visible alarm per ANSI A117.1.

CLIENT: PRATT INSTITUTE - INTERIOR DESIGN - INT 724 Client Address 1 Client Address 2 Client Contact Info

Contact A - Title Contact A - Name Contact A - Address 1 Contact A - Address 2 Contact A - Phone

Contact B - Title Contact B - Name Contact B - Address 1 Contact B - Address 2 Contact B - Phone

Contact C - Title Contact C - Name Contact C - Address 1 Contact C - Address 2 Contact C - Phone

Contact D - Title Contact D - Name Contact D - Address 1 Contact D - Address 2 Contact D - Phone

FINAL SUBMISSION BUILDING DEPARTMENT & GENERAL NOTES 1. Scope of Work: Demolition and interior renovation work of existing apartment 10A. No change of use, occupancy or egress.

TENANT PROTECTION PLAN: RESIDENTIAL RENOVATION §28-104.8.4 Tenant protection plan. Construction documents for alterations of buildings in which any dwelling unit will be occupied during construction shall include a tenant protection plan. Such plan shall contain a statement that the building contains dwelling units that will be occupied during construction and shall indicate in sufficient detail the specific units that are or may be occupied during construction, the means and methods to be employed to safeguard the safety and health of the occupants, including, where applicable, details such as temporary fire-rated assemblies, opening protective, or dust containment procedures. The elements of the tenant protection plan may vary depending on the nature and scope of the work but at a minimum shall make detailed and specific provisions for: 1. Egress. At all times in the course of construction provision shall be made for adequate egress as required by this code and the tenant protection plan shall identify the egress that will be provided. Required egress shall not be obstructed at any time except where approved by the commissioner.

2. Fire Safety. All necessary laws and controls, including those with respect to occupied dwellings, as well as additional safety measures necessitated by the construction shall be strictly observed.

3. Health requirements. Specification of methods to be used for control of dust, disposal of construction debris, pest control and maintenance of sanitary facilities, and limitation of noise to acceptable levels shall be included.

3.1 There shall be included a statement of compliance with applicable provisions of law relating to lead and asbestos.

4. Compliance with housing standards. The requirements of the New York City housing maintenance code, and, where applicable, the New York state multiple dwelling law shall be strictly observed.

5. Structural safety. No structural work shall be done that may endanger the occupants.

6. Noise restrictions. Where hours of the day or the days of the week in which construction work may be undertaken are limited to the New York City noise control code, such limitations shall be stated.

2. Occupancy designation is "residential".

3. Before commencing work, the contractor shall file all required insurance certificates with the Departement of Building , obtain all required permits, and pay all fees required by the governing New York City agencies.

4. All work shall conform to the requirements of the New York City Building Code, Fire Department rules and regulations, utility company requirements, and the best trade practices.

5. Before commencing work, the contractor shall file all required insurance certificates, Workmen's Compensation, etc. with the Department of Buildings. The contractor shall obtain all required permits, and pay all fees required by the governing New York City agencies and shall submit to owner all necessary certificates before commencement of work.

6. Minor details not usually shown or specified, but required for proper construction of any part of the work shall be included as if they were indicated in the drawings.

7. The contractor shall coordinate all work procedures with the stipulations of local authorities, building management, or board of directors.

8. The contractor shall be responsible for the protection of all conditions and materials within the proposed construction area.The contractor shall design and install adequate shoring and bracing for all structural or removal tasks. The contractor shall have sole responsibility for any damage or injuries caused by or during the execution of the work.

9. The contractor shall lay out his own work, and shall provide all dimensions required for all other trades such as: plumbing electrical, etc.

REV NO.

DATE

DESCRIPTION

PRATT INSTITUTE | INT724

10. The contractor shall do all cutting, patching, repairing, etc. As required to perform all of the work indicated on the drawings, and all other work that may be required to complete the job.

11. All piping and wiring shall be removed to a point of concealment and shall be properly capped or plugged.

12. The Architect is responsible for Controlled Inspection for Final Inspection and Firestopping.

The Architect is not responsible for any damages arising out of the Contractor's failure to execute the work exactly as shown on the Approved drawings.

PROJECT:

13. Plumbing work shall be performed by persons licensed in their trades, who shall arrange for and obtain through the Department of Building all required permits, inspections and required sign offs

ATLANTIC AVE RESTAURANT

PLOT PLAN STATE ST

14. Electrical work shall be performed by persons licensed in their trades, who shall arrange for and obtain through the Bureau of Electrical Control all required permits, inspections and required sign offs

ATT LLAA NNTT IICC

100' - 0"

25' - 0"

525 ATLANTIC AVE BROOKLYN NY AAVV EE..

DRAWING TITLE:

General Notes 1 4TH AVE

MFR. MRB. MAS. MAT'L. M.O. MAX. MECH. MEMB. MTL. MEZZ. MIN. MISC. MOD. M.R. MTD. MVBL. MULL. NAT. NOM. N/S N/A N.I.C. N.T.S. NO. O.C. OPG. OPP. O.D. OVHD. PNT. PR. PNL. PART. PED. PERF. P.LAM. PLAS. PL. PLUMB PLWD. PT. LBS. P.C.C. PFB. PROJ. PTD. REC. RE: REIN. REQ'D. RES. REV. R. RF. R.D. RFG. RM. R.O. RND. R.B. SCHED. SCRN. SLNT. SECT. SHT. SDG. SIM. SK. SCW. SPEC. SPR. S.S. STA. STL. STOR. STR. SURF. SUSP. SYM. T.C. TEL. TERR. TH. T.B.D. T.O.S. T.O.W. TR. TYP. U.O.N. V.B. V.C.T. VENT. V.I.F. VERT. VEST. VIN. V.T. W.P. WSTR. WIN. W/ W/O WD.

80' - 0"

ABOVE ABOVE FINISH FLOOR ACCESS ACCESS DOOR ACOUSTICAL TILE ADDENDUM ADJUSTABLE AIR CONDITIONING ALTERNATE ALUMINUM ANODIZED APPROXIMATE ARCHITECT(URAL) ASPHALT AT AUTOMATIC BELOW BETWEEN BITUMINOUS BLOCKING BOARD BOTTOM BRASS BRONZE BUILDING CABINET CARPET CATCH BASIN CEILING CEMENT CENTER CENTER LINE CERAMIC CERAMIC TILE COLUMN COMPANY COMBINE, COMBINATION COMPRESS(ED), (IBLE) CONCRETE CONC. MASONRY UNIT CONNECT CONSTRUCTION CONTINUOUS, CONTINUE CONTRACT LIMIT LINE CONTROL JOINT COUNTERFLASHING DEPRESSED DEGREE DEPARTMENT OF BUILDINGS DRINKING FOUNTAIN DETAIL DIAGONAL DIAMETER DIFFERENT DIMENSION DISPENSER DITTO DIVISION, DIVIDER DOOR DOWEL DOWN DRAWN DRAWING EACH ELECTRIC(AL) ELEVATION ELEVATOR EMERGENCY ENCLOSED EQUAL EQUIPMENT EXHAUST EXPANSION EXPANDED EXPANSION JOINT EXPOSED EXISTING EXTERIOR FACE OF CONCRETE FACE OF FINISH FACE OF MASONRY FACE OF STUDS FIBERBOARD FIXED GLASS FIBERGLASS FINISH(ED) FIRE EXTINGUISHER FIRE EXTING. CABINET FIRE HOSE CABINET FIREPROOF SELF-CLOSING FIXTURE FLASHING FLOOR DRAIN FLOORING, FLOOR FLUORESCENT FOOTING FOUNDATION FURNISHED BY OTHERS FRAMED OPENING FURRING, FURRED GAUGE GALVANIZED GENERAL GENERAL CONTRACTOR GLASS, GLAZING GRADE, GRADING GRAVEL GROUND GYPSUM GYPSUM BOARD HANDICAPPED HANDRAIL HARDWARE HEATER HEATING HEAT, VENT., AIR COND. HEIGHT HOLLOW METAL HORIZONTAL HOUR INCH INCLUDE(D), (ING) INCORPORATE INFORMATION INSIDE DIAMETER INSULATION INTERIOR ISOLATED GROUND JANITOR CLOSET JOINT LAMINATE(D), LAMINANT LIGHTING LINTEL LOCAL LAW

SMOKE/CARBON MONOXIDE DETECTOR NOTES

3RD AVE

ABV. A.F.F ACC. A.D. A.C.T. ADD. ADJ. A/C ALT. ALUM. ANOD. APPROX. ARCH. ASPH. @ AUTO. BEL. BET. BITUM. BLKG. BD. BOT. BRS. BRZ. BLDG. CAB. CPT. C.B. CLG. CEM. CTR. CL CER. C.T. COL. CO. COMB. COMP. CONC. C.M.U. CONN. CONST. CONT. C.L.L. C.J. CFL. DEP. DEG. D.O.B. D.F. DTL. DIAG. DIAM. DIFF. DIM. DISP. DO. DIV. DR. DWL. DN. DRN. DWG. EA. ELEC. EL. ELEV. EMER. ENCL. EQ. EQUIP. EXH. EXP. E.J. EXPO. EXIST. EXT. F.O.C. F.O.F. F.O.M. F.O.S. FBD. F.G. FGL. FIN. F.E. F.E.C. F.H.C. FPSC. FIXT. FLG. F.D. FLR. FLUOR. FTG. FDN. F.B.O. F.O. FUR. GA. GALV. GEN. G.C. GL. GRD. GRAV. GRND. GYP. GYP. BO. HDCP. HDRL. HDW. HTR. HTG. H.V.A.C. HT. H.M. HORIZ. HR. IN. INCLUDE. INC. INFO. I.D. INSUL. INT. I.G. J.C. JT. LAM. LTG. LIN. LL.

ENERGY CODE NOTES

ATLANTIC AVE. SEAL & SIGNATURE

525 ATLANTIC AVE AVE BLOCK 180 LOT 60 ZONING R7A/ C2-4 MAP 16C

WORK AREA OF WORK GROUND FLOOR GROUND FLOOR SECOND FLOOR FLOOR

DATE:

Issue Date

PROJECT NO. 17-724-04 DRAWING BY: Author CHK BY:

Checker

DRAWING NO.

7

Plot Plan 1" = 100'-0"

T-001

PROJECT TEAM:

GENERAL NOTE

1. All work and materials furnished shall comply with the state of New York Building Code, and the Building Management Street Rules and Regulations for Construction, The state of New York fire code, the State of New York regulations, the regulations of the board of fire underwriters, national fire protective association requirements and all federal, state and municipal authorities having jurisdiction over the work.

2. The building permit shall be secured by the Construction Manager or General Contractor (hereby known as the General Contractor) and he shall obtain all other permits and approval as required by law for the completion of the project.

3. The submission of a proposal by the General Contractor will be constructed as evidence that a careful and thorough examination of the premises has been made and later claims for labor, materials, or equipment or for difficulties encountered which could have been foreseen had such an examination been made, will not be recognized. It shall also constitute a representation that the General Contractor has checked and verified all quantities, work and materials involved and that he shall take responsibility for any deficiencies therein.

4. Before ordering any material or commencing with any of the work described in the enclosed documents, each trade shall verify all measurements at the premises and shall be responsible for the correctness of same. No extra charge or compensation will be allowed on account of differences between actual dimensions and measurements indicated on the drawings; any discrepancies between the drawings and the field conditions which may be found shall be submitted to the Architect for consideration and clarification before proceeding with the work.

16. For the execution of the work to be performed under this contract and for the manufacture or transportation of any of the materials or appliances to be used or installed. The contractor shall employ only such labor throughout as will not interfere with the speedy and uninterrupted completion of the project. All work shall be performed by mechanics skilled in their trade and shall be installed in a neat and workmanlike manner in accordance with the best trade practices.

5' - 0" MIN

3'-6" MIN

4' - 0" MIN

4' - 0" MIN

17"-19"

15"-48"

33"-36"

4'-0" MIN

27" MIN 29" MIN 34"

9" MIN

38" MAX

WATER CLOSETS

REINFORCED AREAS FOR INSTALLATION OF GRAB BARS

5'-6" MIN

LAV

REQUIRED MINIMUM DIMENSIONS AS PER ANSI 117.1

4.32.4.4

5'-0"

CLEAR FLOOR SPACE

LAV.

CLEAR FLOOR SPACE

1'-0" 3'-6" MIN MAX FLOOR MTD TOILET (RESIDENTIAL)

4.21 SHOWER STALLS

f) Do all other cleaning as required to turn premises over to owner in a spotless and orderly manner.

BATHTUBS 2'-0" 2'-0" MAX MIN

42" MIN.

1'-0" MAX

FLOOR MTD TOILET (RESIDENTIAL)

1'-0" MAX

2'-0" MIN

LAV

CLEAR FLOOR SPACE

2'-0" MIN

5'-0"

LOCATION OF GRAB BAR REINFORCEMENTS OF ADAPTABLE BATHTUBS

CONTROL PANEL

6" MAX. 6" MAX. 4'-0" MIN.

SEAT

SEAT

REV NO.

1'-3" MAX

DATE

DESCRIPTION

PRATT INSTITUTE | INT724

5'-0" 30"X60" STALL

LOCATION OF GRAB BAR REINFORCEMENTS FOR ADAPTABLE SHOWERS

27. All work shall be subject to final inspection by the Architect and acceptance by the Owner.

5'-0" BATHTUB WITH SEAT IN TUB 4.32.5.5

ADAPTABLE BATHTUB WITH SEAT IN TUB

PROJECT:

ADJUSTABLE COUNTER SEGMENT

CONTROL PANEL

30" MIN. SIDE

BACK

ADAPTABLE BATHTUB WITH SEAT IN TUB

KITCHEN SINK

2'-3" MAX

28. The General Contractor shall guaranteed the work against defects in materials, workmanship or installation for a period of two years from the date of final acceptance of completed work by Owner; and he shall at his own expense and without cost to the Owner. correct any defects which may develop during such two year period and correct any damage to other work cause by such defects or repairing of same.

29. All miscellaneous penetrations & miscellaneous steel lintels as required for installation of all piping, ductwork etc. as indicated on MEP plans are within the G.C. scope of work & are to be coordinated with all subcontractors.

3'-0" MIN. 6" MAX.

4.32.4.2

d) Clean and polish all hardware, and other metal work.

26. The General Contractor shall keep the Architect apprised of the progress of his work by providing weekly written reports describing work completed during the week and work proposed for the upcoming week No work shall be closed or covered until it has been duly inspected and approved.

Should un-inspected work be covered, the contractor shall at his own expense uncover all such work so that it can be properly inspected and after such inspection he shall properly repair and replace all work interfered with.

8" MIN

17" MIN LAVATORY AND MIRROR

30" MIN LAVATORY

a) A thorough cleaning throughout including washing or cleaning by other approved methods of all floors and surfaces on which or dust has collected and by washing, removing all paint, putty, stains, etc. therefrom.

e) Maintain exterior of building and property in a neat, clean. safe and orderly manner. Store all refuse trash and rubbish in secure animal proof containers. Contractor shall at his own expense arrange to have construction trash, waste and debris removed from the premises on a weekly basis.

MIRROR

6" MAX

25. In addition to cleaning the specified above and more specific cleaning which may be required in various sections of the specifications. the premises shall be prepared for occupancy by the following:

14. The contractor shall submit all fabrication shop drawings, samples and fixture cuts for the Architect's review as required and/or indicated on the drawings. The Architects's review shall not be taken as an indication that submittal is correct or suitable, nor that work represented by submittal complies with the drawings except as to matters of finish, color, textures and other aesthetic matters. Action noted above does not relieve the contractor from the responsibility to coordinate all trades and to check quantities and dimensions against conditions in the field. Contractors and engineers shall assume responsiblity for all errors and omissions on their drawings. (Submit four copies of each shop drawing or fixture cuts or samples.)

15. All materials required for the performance of this contract shall be new and of the best quality of kinds specified, all subject to the approval of the Architect. The use of old or second-hand materials is strictly forbidden. The General Contractor shall, if required, furnish satisfactory evidence as to the kind and quality of materials and workmanship. Materials shall be used in accordance with manufacturer's printed instructions. Upon request, the manufacturer's representative shall go to the site and instruct the mechanics in the use of the materials and supervise their use.

CLEAR FLOOR SPACE

24. This cleaning includes the removal of trash and rubbish form these areas, broom cleaning of floors, the removal of any plaster, mortar, dust, and other extraneous materials from finish surfaces, including but not limited to miscellaneous metal, woodwork, plaster, gypsum, drywall, masonry, concrete, mechanical and electrical equipment, piping ductwork, conduit, surfaces visible after permanent fixture induction, unit covers, grilles and registers and other such fixtures or devices are in place.

c) Leaving all surfaces, fixtures and equipment in an undamaged, bright. clean. polished condition.

19" MAX

23. Clean areas of the building in which painting and finishing work is to be performed just prior to the star of this work, and maintain these areas in satisfactory condition for painting and finishing.

b) Providing and maintaining adequate runner strips of nonstaining reinforced Kraft building paper on finished floors as required for protection.

FINAL SUBMISSION 48" MIN

22. Clean up immediately upon completion of each trade's work.

LAVATORIES

3'-2" MIN 2'-8" MAX

GENERAL CONSTRUCTION NOTES:

4.19

FLOOR MTD TOILET (COMMERCIAL)

3'-2" MIN

21. Upon completion of the demoltion work, the general contractor shall provide that all areas are left broom clean.

FLOOR MTD TOILET (COMMERCIAL)

2'-8" MAX

20. The general contractor shall furnish temporary heat if ambient temperatures drop below freezing.

1'-0" MAX 3'-6" MIN

21. Care shall be taken by workers not to mark, soil or otherwise deface finished surfaces. In the event that finished surfaces become defaced, clean and restore such surfaces to their original condition.

13. The General Contractor shall coordinate and supervise the work of all contractors and sub-contractors. He shall be responsible for giving all trades such information, plans or details as may be required for the proper execution, installation and completion of their work. All materials shall be ordered sufficiently ahead of time so that work can proceed on schedule. No substitutions will be accepted because of failure to do so.

7"-9"

3'-2" MIN

19. The general contractor shall furnish a system of temporary power and lights throughout the space under construction as required.

12. The General Contrator shall notify the Architect immediately if he cannot for any reason comply with all the requirements of these notes and drawings.

Contact D - Title Contact D - Name Contact D - Address 1 Contact D - Address 2 Contact D - Phone

36" MAX.

6" MAX

18. The general contractor shall at all times protect that property of the building owner which is to remain.

11. The standard specifications of the Manufacturer's approved for use in the project are hereby made as of these notes with the same force and effect as though herin written out in full, except that wherever the drawings require heavier members, better quality material materials or are otherwise more stringent, these more stringent requirements shall govern.

SLIDING DOOR - SIDE APPROACH

38" MIN 32" MAX

17. The general contractor shall erect all necessary temporary protective structures such as scaffolding, fencing, barricades or bridges, and plastic drop cloth partitions to protect adjacent areas outside of scope of work while demolition and construction are in progress, where applicable.

CLEAR FLOOR SPACE

2'-0" MIN

16. In all areas where demolition (removal of finish floor, partitions, etc.) causes an unevenness in slab, the contractor shall patch to level the slab to receive new finished flooring.

TOILET PAPER

20. The Contractor shall be responsible for protecting all external portions of the site including but not limited to; all structures on the property, sidewalks, landscape elements. driveways. walkways. and fences. The Contractor shall be responsible for the repair and/or replacement of any of above said items damaged or destroyed during the course of executing the project. Electrical closets. pipe and duct shafts, chases, furred spaces

Contact C - Title Contact C - Name Contact C - Address 1 Contact C - Address 2 Contact C - Phone

12" MAX

42" MIN.

4'-0" MIN

15. All work will be removed from the premises except items to be reused ro returned to Owner or as otherwise directed.

SLIDING DOOR - FRONT APPROACH

5'-6" MIN

28"-36"

14. The general contractor shall execute all work within the regulations of all Regulatory Agencies having jurisdiction over this project for demoltion and removal of debris, including after hours work required.

10. The project has been designated and detailed for the specific materials and equipment specified. No substitutions shall be made without the express written consent of the Architect. If the specified material is not available, the Contractor shall propose an alternate material and shall provide drawings, samples, specifications, manufacturer's literature, performance date, etc. in order that the Architect can evaluate the proposed substitution. If the substitution affects a correlated function, adjacent construction, or the work of any other contractor or trade, the necessary changes and modifications to the affected work shall be accomplished by the General Contractor at no additional expense to the owner. No requests for substitutes will be entertained by the Architect due to Contractor's failure to order materials in a timely manner.

2' - 0"

WATER CLOSETS

2'-0"MIN

13. The general contractor shall furnish all labor and materials as required to complete demolition and removal of all items as indicated in the drawings or as otherwise directed by the Architects.

PUSH SIDE - FRONT APPROACH 4.16

Contact B - Title Contact B - Name Contact B - Address 1 Contact B - Address 2 Contact B - Phone

MIN

SEAT

12. Any damage incurred outside of the scope of work must be repaired.

1' - 0" MIN

4'-0"

11. Demolished materials should be removed from the site and passageways and exterior spaces should be kept clean continuously.

9. Full size or large scale details or drawings shall govern small scale drawings which they are intended to amplify.

Details or conditions indicated for a portion of the work but not carried out fully for other portions shall apply throughout to all similar portions except as otherwise specifically noted.

In every case a more expensive item or method shall be assumed over a less expensive one and dimensions shall be figured rather than determined by rule or scale.

19. The premises and the job site shall be maintained in a reasonably neat, orderly and safe condition and kept free from accumulations of waste materials and rubbish during the entire construction period. Remove crates, cartons, and other flammable waste material or trash from the work areas at the end of each working day and remove from the site at the end of each working week. Said material shall bea stored in an exterior location that presents no risk of damage to any portioin of the Owner's property in sealed fire-proof and animal proof containers while awaiting removal from the site.

Removal of construction materials and debris shall be subject to the rules and regulations of the state, federal and municipal authorities and agencies having jurisdiction. Any fines or citations issued form failure to comply with waste removal regulations shall be understood to be the responsibility of the Contractor.

1'-6" 1'-6"

10. The General Contractor shall use only licensed and certified sub-contractors for the removal of refrigerant in existing mechanical lines. Refrigerant to be removed using only EPA, state DEP and locally approved collection methods and equipment.

8. The character and scope of the work are illustrated by the drawings and notes. To interpret and explain the drawings other information deemed necessary by the Architect will be furnished to the contractor when and as required by the work, and it is to be understood that said additional information or drawings are to be of equal force with these drawings.

PULL SIDE - FRONT APPROACH

17" MIN

9. The General Contractor shall drain all plumbing and mechanical water supply lines and cap them at their source before proceeding to demolish them.

Contact A - Title Contact A - Name Contact A - Address 1 Contact A - Address 2 Contact A - Phone

54" MIN

3'-0"

8. The General Contractor shall prevent damage to building interior stairs and exterior fire escapes, elevators and shafts, facade elements, steel, fireproofing, building main utilities, electric service, domestic water, etc., as required.

1' - 6"

32" MIN

1'-6" 1'-6"

7. At juncture of work to remain and work to be demolished, make neat, straight, plumb even cuts.

7. The General Contractor shall abide by and comply with the true intent and meaning of the drawings and notes taken as a whole and shall not avail himself of any obvious errors and omissions, should any exist. Should any error or discrepancy appear or any doubt arise as to the true meaning of the drawings or notes, the contractor shall bring such items to the attention of the Architects before submission of his proposal for an explanation, clarification or correction of same. After the submission of proposal the contractor will be held responsible for all such items.

4' - 0" MIN

DOORS IN SERIES

1'-0" MIN

6. Protect all existing work from damage by impact, soiling, water.

CLIENT: PRATT INSTITUTE - INTERIOR DESIGN - INT 724 Client Address 1 Client Address 2 Client Contact Info

MIN

2'-8"MAX 6"

5. The general contractor shall cap and flush off behind floor and wall surfaces to remain all projecting plumbing, floor and wall electrical/ telephone outlets, and all other projecting items which are being abandoned.

18. The General Contractor shall be responsible for properly and accurately laying out the work and for the lines and measurements herein. He shall establish necessary reference lines and permanent bench marks from which building lines and elevations shall be taken. Heights of all work called "A.F.F." including to but not limited to soffits, ceilings, and doors shasll be true and level within a maximum tolerance of 1/8" overall throughout the entire project regardless of variations in the actual floor or slab. The slab or floor shall be leveled as required so as not to vary more than 1/8" in any 10'-0". General Contractor to inform Architet before proceeding with any work if the above stated minimums are not achievable.

4'-0" MAX

4. Remove all fixtures, appliances, equipment and hardware in all areas within the limits indicated as extent of work.

6. The work to be performed consists of all furnishing labor, equipment, tools, transportation, supplies, fees, materials and services in accordance with these notes and drawings and performing all operations necessary to construct and install complete and satisfactory condition the various materials and equipment at the locations shown, and in conformity with the dimensions, design and details shown. It is intended that the drawings include everything requisite and necessary to finish the entire project properly not withstanding the fact that every item necessarily involved may not be specifically mentioned or shown. Any item which may be reasonably constructed as incidental to the proper and satisfactory completion of the work in accordance with the intent of these notes and drawings is hereby included.

DOORS

4' - 0" MIN

2'-8"MAX 6"

3. The General Contractor or Sub Contracors (hereby to be referred to as the General Contractor) shall furnish all labor and materials as required to complete demolition and removal of all items as indicated in the drawings or as otherwise directed by the Architects.

4.13

2'-6" MIN

2. Notify architect of discrepancies between drawings and existing conditons prior to proceeding with work.

17. Any materials delivered or work perfomed, contrary to the drawings and specifications and approved shop drawings, shall be removed by the Genereal Contractor at his own expense, and the same shall be replaced with other materials or work satisfactory to the Architect. The General Contractor shall also assume the cost of replacing the work which may be disturbed.

3'-0"

1. Existing conditions, materials and dimensions indicated are for general information only. Remove existing construction completely to extent indicated or required, whether or not indicated material, configurations and dimensions are correct.

Verify existing conditions.

5. All of the architects' drawings and construction notes are complimentary and what is called for by either will be binding as if called for by all. Any work shown or referred to on any one drawing shall be provided as though shown on all drawings. Whenever an item is specified and/or shown on the drawings by detail of reference it shall be considered typical for other items which are obviously intended to be the same even though not so designated of specifically named, but do serve the same function.

2'-8"MAX 6"

DEMOLITION NOTES

INTERIOR DESIGNER NAME ADDRESS 1 ADDRESS 2 T: xxx.xxx.xxxx; F: xxx.xxx.xxxx

REQUIRED MINIMUM DIMENSIONS AS PER ANSI 117.1

SUGGESTED FLEXIBLE SUPPLY LINES

SUGGESTED SLIP JOINT IN TAIL PIECE

ATLANTIC AVE RESTAURANT

525 ATLANTIC AVE BROOKLYN NY DRAWING TITLE:

General Notes 2

SIDE

NOTE: SHOWER HEAD & CONTROL AREA MAY BE ON BACK WALL (AS SHOWN) OR 30"X60" STALL ON EITHER SIDE WALL

ADAPTABLE KITCHEN SINK W/ BASE CABINET REMOVED

SEAL & SIGNATURE

DATE:

Issue Date

PROJECT NO. 17-724-04 DRAWING BY: Author CHK BY:

Checker

DRAWING NO.

T-002

PROJECT TEAM:

5 ADA Restroom

INTERIOR DESIGNER NAME ADDRESS 1 ADDRESS 2 T: xxx.xxx.xxxx; F: xxx.xxx.xxxx

1 2 4 A-600.00 W-4

W-2

3

Room Schedule 1 Level

ADA Restroom

4' - 2"

SN-1

3' - 5"

10

2' - 2"

Free Standing Seating

6' - 11"

51 W-1 5' - 6"

4 A-600.00 2

20

1 A-600.00

3

Number

Level 1

1

Level 1

2

2

Level 1

3

Level 2 Ceiling Plan Level 2 Ceiling Plan

4

W-1

01 9' - 0"

13' - 3"

W-4

5

Name ADA Restroom Free Standing Seating Bar with Back Bar Build-in&Fr ee-standing Seating Manager Office

Area

CLIENT: PRATT INSTITUTE - INTERIOR DESIGN - INT 724 Client Address 1 Client Address 2 Client Contact Info

76 SF 1022 SF

Contact A - Title Contact A - Name Contact A - Address 1 Contact A - Address 2 Contact A - Phone

436 SF 582 SF

Contact B - Title Contact B - Name Contact B - Address 1 Contact B - Address 2 Contact B - Phone

95 SF

W-1

Contact C - Title Contact C - Name Contact C - Address 1 Contact C - Address 2 Contact C - Phone

UP

W-4

Free Standing Seating

Room Legend

UP

Bar with Back Bar

ADA Restroom

3 11' - 11"

27' - 9 1/8"

2

Bar with Back Bar

NIC

W-1

Contact D - Title Contact D - Name Contact D - Address 1 Contact D - Address 2 Contact D - Phone

Free Standing Seating

FINAL SUBMISSION

19

W-5

3

Level 1 AA 1/8" = 1'-0"

W-5 W-5

W-3 6' - 4"

Manager Office 5 3' - 6"

10' - 6 1/2"

1

W-1

UP

W-3

W-3 UP

DN

Generic - 14" Terrazzo floor

Back Bar

W-5 W-5

Bar W-1

14

NIC

Bar with Back Bar 3' - 8"

W-2

9' - 10" REV NO.

7

3

DATE

DESCRIPTION

PRATT INSTITUTE | INT724

1' - 11"

UP

5 A-300.00

8' - 0"

1 A-200.01

17' - 2"

Build-in&Free-standing Seating

3 A-500.00

NIC

CA-1 Office Manager UP

4 19' - 4 1/2"

17' - 9"

11' - 11"

1 A-200.01

Bar

PROJECT:

5

DN

ATLANTIC AVE RESTAURANT

NIC

525 ATLANTIC AVE BROOKLYN NY

Room Legend DRAWING TITLE:

2 DN

Manager Office

2' - 10"

4 1' - 8"

6' - 2"

Construction Plan

Build-in&Free-standing Seating

Build-in&Free-standing Seating

10' - 3" DN SEAL & SIGNATURE

DATE:

Issue Date

PROJECT NO. 17-724-04

24

-

-

2 A-200.00

1

Level 1 Construction Annotate 1/4" = 1'-0"

2 A-200.00

2

Level 2 Construction Annotate 1/4" = 1'-0"

-

19

DRAWING BY: Han Xiao CHK BY:

Checker

DRAWING NO.

A-100.00 4

Level 2 AA 1/8" = 1'-0"

PROJECT TEAM:

Door Schedule ?

Count

ADA Restroom 51

1-ADA Restroom Floor Wall CLG

4 A-600.00 2 3

PT01 PT01 ACT01

01

Type

Finish

Frame Material

Type Mark

Head Height

Width

Thickness

Height

7

36" x 84"

Pine Wood Pine Wood 1

3' - 0"

7' - 0"

0' - 2"

7' - 0"

1

34" x 84"

Pine Wood Pine Wood 2

2' - 10"

7' - 0"

0' - 2"

7' - 0"

1

36" x 96"

Walnut Wood

3' - 0"

8' - 0"

0' - 1 3/8"

8' - 0"

Walnut Wood

8

INTERIOR DESIGNER NAME ADDRESS 1 ADDRESS 2 T: xxx.xxx.xxxx; F: xxx.xxx.xxxx

Keynote 1H Fire-rated 1H Fire-rated 1H FIre-rated

CLIENT: PRATT INSTITUTE - INTERIOR DESIGN - INT 724 Client Address 1 Client Address 2 Client Contact Info

Contact A - Title Contact A - Name Contact A - Address 1 Contact A - Address 2 Contact A - Phone

3' - 0 1/16"

Contact B - Title Contact B - Name Contact B - Address 1 Contact B - Address 2 Contact B - Phone

3' - 0"

3' - 0"

Terrazzo

Free Standing Seating

Contact C - Title Contact C - Name Contact C - Address 1 Contact C - Address 2 Contact C - Phone

3' - 0"

2 2-Free Standing Seating Floor Wall CLG

3' - 5 1/2"

TRE MAR01 WP01

3' - 0 1/2"

Contact D - Title Contact D - Name Contact D - Address 1 Contact D - Address 2 Contact D - Phone

3' - 6"

7' - 0"

7' - 3"

Wood

8' - 0 1/4"

8' - 2 3/4"

3' - 0"

FINAL SUBMISSION

Terrazzo

Manager Office 5

1

5-Manager Office Floor Wall CLG

UP UP

Door Elevation 1/2" = 1'-0"

CPT White Marble Tile WP01

DN

Material Plan

NIC

Number Terrazzo

UP

Vinyl

2

Free Standing Seating Bar with Back Bar Build-in&Fr ee-standing Seating Manager Office

Terrazo

4

3-Bar With Back Bar Floor Wall CLG

ADA Restroom

3

3

TER MAR01 WP01

Build-in&Free-standing Seating

5

4

NIC

Floor Finish Wall Finish

1

Generic Roof - 14"

Bar with Back Bar

Name

Ceiling Finish

Level

Area

White Acoutic ceiling Panel Level 1 marble tile& white paint Marble Concrete Like Level 1 Wallcovering

76 SF

Terrazo

Marble

Level 1

436 SF

Terrazo

Marble

582 SF

Carpet

Wallpaper

Level 2 Ceiling Plan Level 2 Ceiling Plan

Expose to the second floor Concrete Like Wallcovering White Paint

Terrazzo

1022 SF

95 SF

REV NO.

DATE

DESCRIPTION

PRATT INSTITUTE | INT724

4-Build-in&Free-Standing Seating Floor Wall CLG

2

TER MAR01 WP01

MATERIAL FINISH LEGEND MARK

NOTE

MATRAIL LEGEND

DN

PT01

White Marble Tile

TER

Terrazzo

PROJECT:

ATLANTIC AVE RESTAURANT

525 ATLANTIC AVE BROOKLYN NY DRAWING TITLE:

-

-

-

-

CONC

Concrete

ACT01

Acoustic Ceiling Tile 24''*48''

CPT

Soft Floor Carpet Tile

Finish Plan, Door Elevation and Schedules

SEAL & SIGNATURE

WP01

1

Level 1 Material Plan 1/4" = 1'-0"

2

Level 2 Material Plan 1/4" = 1'-0"

Concrete Like Wallpaper

DATE:

Issue Date

PROJECT NO. 17-724-04 DRAWING BY: Han Xiao CHK BY:

Checker

DRAWING NO.

A-101.00

PROJECT TEAM:

INTERIOR DESIGNER NAME ADDRESS 1 ADDRESS 2 T: xxx.xxx.xxxx; F: xxx.xxx.xxxx

Furniture Schedule SN-1

ADA Restroom

4' - 2"

2' - 2"

Manufactur er

6' - 11 3/8"

51 4 A-600.00 2 3

5' - 2"

6' - 0"

2' - 2"

01

S-2

TBL-3

TBL-2

TBL-2

.

CH-3

.

CH-3

TBL-2

S-2

.

Generic - 14" CH-3 Terrazzo floor

CH-3 .

CH-3 .

TBL-2

TBL-2

.

CH-3

.

CH-3

Free Standing Seating CH-3

TBL-3

.

8' - 11"

2

23' - 10"

TBL-2

.

CH-3

S-2 TBL-3

CH-3 .

TBL-2 S-3

CH-3 .

8' - 8"

3' - 4"

CH-3 .

CH-3 .

CH-3 .

TBL-2

TBL-2

.

CH-3

.

CH-3

Brand

Model

Color

Finish

Haworth

Haworth

Alias Alias

Alias Alias

Offecct

Offecct

Haworth Chair Lotus High Bar Chair Bar Chair Lucy 2 seater

Offecct

Offecct

Lucy 3 seater

Various

Upholstered

5 Spoke Chair with Glides

Various Various

Wood Wood

Various

Upholstered & lacquered Upholstered & lacquered

Alias Taormina 503 Default Furniture_Sofas&Armchairs_Offecct_ Lucy-sofasystem-B20 Furniture_Sofas&Armchairs_Offecct_ Lucy-sofasystem-B30 Haworth_Chair_Exchange

Haworth

Knoll, Inc

Wood

Knoll, Inc.

Knoll, Inc

Haworth_Chair_E Yellow xchange Yellow Type Catalog

Knoll, Inc. Knoll, Inc.

Knoll, Inc Knoll, Inc

Bertoia Type Catalog

Yellow Red

Wood Leather

Knoll, Inc.

Knoll, Inc

Type Catalog

Red

Leather

Knoll, Inc.

Knoll, Inc

Type Cat alog

Red

Leather

Knoll, Inc.

Knoll, Inc

Type Catalog

Red

Leather

Vitra

Vitra

Bar Chair

Red

Leather

Vitra

Vitra

Bar Chair

Red

Leather

Various

Wood

CLIENT: PRATT INSTITUTE - INTERIOR DESIGN - INT 724 Client Address 1 Client Address 2 Client Contact Info

Type

Contact A - Title Contact A - Name Contact A - Address 1 Contact A - Address 2 Contact A - Phone

Contact B - Title Contact B - Name Contact B - Address 1 Contact B - Address 2 Contact B - Phone

Knoll_Studio_Bertoia_Diamond_Loun ge_Adult Knoll_Studio_Bertoia_Molded_Shell Knoll_Studio_Gehry_Face_Off_Cafe _Table Knoll_Studio_Pensi_Square_Large_ Bistro_Tables Knoll_Studio_Risom_Tables_Side_R ound Knoll_Studio_Saarinen_Tulip_Chairs _Armless TOP - (Oak veneer) Base (Chrome-NA) Type - (Black Wood Upholstered Seat)

Contact C - Title Contact C - Name Contact C - Address 1 Contact C - Address 2 Contact C - Phone

Contact D - Title Contact D - Name Contact D - Address 1 Contact D - Address 2 Contact D - Phone

FINAL SUBMISSION

.

CH-3

TBL-3

CA-2

CA-2 Generic - 14"

CA-2

CA-2

CA-2 CH-6

S-1

1

TBL-1 TBL-4

S-1 CA-1

Manager Office

UP

TBL-1

5

CH-5

TBL-1

UP

DN

S-1 S-1

1' - 8"

2' - 6"

3' - 8"

NIC

10' - 3"

CH-1

CH-1

CH-1 CH-1

CH-2 2' - 4"

UP

Bar with Back Bar 3

CH-1

2

0' - 8"

CH-2

CH-1

CH-1

CH-1

CH-1 PROJECT:

CH-4

CH-4

CH-1

CH-4

CH-4

TBL-3

TBL-3

1' - 7"

CH-4

ATLANTIC AVE RESTAURANT

CH-1

525 ATLANTIC AVE BROOKLYN NY

TBL-4

TBL-3 CH-2

CH-1

CH-1

DN DRAWING TITLE:

CH-4 CH-4

TBL-3 CH-2

CA-2

Generic - 14" Terrazzo floor with ceiling

-

Level 1 Furniture Annotate 2 1/4" = 1'-0"

Level 2 Furniture Annotate 1 1/4" = 1'-0"

Furniture Plan

CA-2

SEAL & SIGNATURE

-

DESCRIPTION

PRATT INSTITUTE | INT724

TBL-3

CH-2

3' - 2"

CH-1

DATE

TBL-4 Build-in&Free-standing Seating

4 TBL-3

3' - 4"

CH-2

TBL-1

CH-2

3' - 6"

NIC

CH-2

CH-1

REV NO.

CH-7

CH-4

2' - 4"

Bar

TBL-1

TBL-1

2' - 4"

CH-1

TBL-3

CH-7

CH-2

2' - 2"

Back Bar

2' - 4"

11' - 11"

CH-2

2' - 2"

CH-2

TBL-4

TBL-3

DATE:

Issue Date

PROJECT NO. 17-724-04 DRAWING BY: Han Xiao CHK BY:

Checker

DRAWING NO.

A-102.00

PROJECT TEAM:

INTERIOR DESIGNER NAME ADDRESS 1 ADDRESS 2 T: xxx.xxx.xxxx; F: xxx.xxx.xxxx

CLIENT: PRATT INSTITUTE - INTERIOR DESIGN - INT 724 Client Address 1 Client Address 2 Client Contact Info

Contact A - Title Contact A - Name Contact A - Address 1 Contact A - Address 2 Contact A - Phone

39' - 8"

Contact B - Title Contact B - Name Contact B - Address 1 Contact B - Address 2 Contact B - Phone

37' - 9"

Contact C - Title Contact C - Name Contact C - Address 1 Contact C - Address 2 Contact C - Phone

Roof 39' - 0"

Contact D - Title Contact D - Name Contact D - Address 1 Contact D - Address 2 Contact D - Phone

Level 3 27' - 0"

FINAL SUBMISSION

Built in & Free Standing Seating

Manager Office Bar With Back Bar

Free Standing Seating Level 2 Ceiling Plan 15' - 0"

---

Level 1 0' - 0"

Cellar -9' - 6"

REV NO.

DATE

DESCRIPTION

PRATT INSTITUTE | INT724

PROJECT:

ATLANTIC AVE RESTAURANT

525 ATLANTIC AVE BROOKLYN NY DRAWING TITLE:

Longitudinal Section

SEAL & SIGNATURE

DATE:

Issue Date

PROJECT NO. 17-724-04

2

Section 3 1/4" = 1'-0"

DRAWING BY: Han Xiao CHK BY:

Checker

DRAWING NO.

A-200.00

PROJECT TEAM:

INTERIOR DESIGNER NAME ADDRESS 1 ADDRESS 2 T: xxx.xxx.xxxx; F: xxx.xxx.xxxx

CLIENT: PRATT INSTITUTE - INTERIOR DESIGN - INT 724 Client Address 1 Client Address 2 Client Contact Info

Contact A - Title Contact A - Name Contact A - Address 1 Contact A - Address 2 Contact A - Phone 25' - 10"

Contact B - Title Contact B - Name Contact B - Address 1 Contact B - Address 2 Contact B - Phone

Roof 39' - 0"

Contact C - Title Contact C - Name Contact C - Address 1 Contact C - Address 2 Contact C - Phone

Contact D - Title Contact D - Name Contact D - Address 1 Contact D - Address 2 Contact D - Phone

Level 3 27' - 0"

FINAL SUBMISSION

Level 2 Ceiling Plan 15' - 0"

1 A-504.00

Sim

Level 1 0' - 0" REV NO.

DATE

DESCRIPTION

PRATT INSTITUTE | INT724 Cellar -9' - 6" PROJECT:

ATLANTIC AVE RESTAURANT

525 ATLANTIC AVE BROOKLYN NY DRAWING TITLE:

1

Transverse Section

Section 2 1/4" = 1'-0"

SEAL & SIGNATURE

DATE:

Issue Date

PROJECT NO. 17-724-04 DRAWING BY: Author CHK BY:

Checker

DRAWING NO.

A-200.01

PROJECT TEAM:

INTERIOR DESIGNER NAME ADDRESS 1 ADDRESS 2 T: xxx.xxx.xxxx; F: xxx.xxx.xxxx

CLIENT: PRATT INSTITUTE - INTERIOR DESIGN - INT 724 Client Address 1 Client Address 2 Client Contact Info

3 A-300.00

Contact A - Title Contact A - Name Contact A - Address 1 Contact A - Address 2 Contact A - Phone

Contact B - Title Contact B - Name Contact B - Address 1 Contact B - Address 2 Contact B - Phone

Contact C - Title Contact C - Name Contact C - Address 1 Contact C - Address 2 Contact C - Phone

1 A-300.00

Contact D - Title Contact D - Name Contact D - Address 1 Contact D - Address 2 Contact D - Phone

FINAL SUBMISSION 1 A-301.02

Sim

REV NO.

1 A-301.01

5

Level 2 Construction Annotate - Callout 1 1/2" = 1'-0"

1

Stair Section 1/2" = 1'-0"

3

Section 4 1/2" = 1'-0"

Sim

DATE

DESCRIPTION

PRATT INSTITUTE | INT724

PROJECT:

ATLANTIC AVE RESTAURANT

525 ATLANTIC AVE BROOKLYN NY DRAWING TITLE:

Staircase plan and sections

SEAL & SIGNATURE

DATE:

Issue Date

PROJECT NO. 17-724-04 DRAWING BY: Author CHK BY:

Checker

DRAWING NO.

A-300.00

PROJECT TEAM:

2' - 8"

INTERIOR DESIGNER NAME ADDRESS 1 ADDRESS 2 T: xxx.xxx.xxxx; F: xxx.xxx.xxxx

0' - 1"

CLIENT: PRATT INSTITUTE - INTERIOR DESIGN - INT 724 Client Address 1 Client Address 2 Client Contact Info

Contact A - Title Contact A - Name Contact A - Address 1 Contact A - Address 2 Contact A - Phone

Contact B - Title Contact B - Name Contact B - Address 1 Contact B - Address 2 Contact B - Phone

Contact C - Title Contact C - Name Contact C - Address 1 Contact C - Address 2 Contact C - Phone

Contact D - Title Contact D - Name Contact D - Address 1 Contact D - Address 2 Contact D - Phone

12''*12''*1'' TERRAZZO FL 0' - 11"

1/4'' BONDING AGENT

0' - 1 13/16"

0' - 1 1/2"

FINAL SUBMISSION

ALUMINUM HANDRAIL 3' - 6"

2'' CONC SLAB BACKERBD 0' - 1"

GLASS PANEL CONCRETE

3/4'' PLYWD SUBFL REV NO.

0' - 0 1/8"

DESCRIPTION

PRATT INSTITUTE | INT724

1/8'' METAL PAN

0' - 11"

DATE

2''*4'' WD FRAME 3''*10'' C CHNNEL

0' - 7"

0' - 1 7/8"

0' - 11 1/4"

PROJECT:

ATLANTIC AVE RESTAURANT

BOLT 1/2'' METAL BASE

525 ATLANTIC AVE BROOKLYN NY

2''*10'' WD JOIST DRAWING TITLE:

Staircase details

SEAL & SIGNATURE

DATE:

Issue Date

PROJECT NO. 17-724-04 DRAWING BY: Author CHK BY:

Checker

DRAWING NO.

A-301.01 1

Stair desing 2 3" = 1'-0"

PROJECT TEAM:

INTERIOR DESIGNER NAME ADDRESS 1 ADDRESS 2 T: xxx.xxx.xxxx; F: xxx.xxx.xxxx

GLASS PANEL

CLIENT: PRATT INSTITUTE - INTERIOR DESIGN - INT 724 Client Address 1 Client Address 2 Client Contact Info

HANDRAIL

0' - 1 1/2"

Contact A - Title Contact A - Name Contact A - Address 1 Contact A - Address 2 Contact A - Phone

Contact B - Title Contact B - Name Contact B - Address 1 Contact B - Address 2 Contact B - Phone

Contact C - Title Contact C - Name Contact C - Address 1 Contact C - Address 2 Contact C - Phone

Contact D - Title Contact D - Name Contact D - Address 1 Contact D - Address 2 Contact D - Phone

FINAL SUBMISSION

3' - 6 1/8"

METAL CLAP

0' - 10"

0' - 7"

3''*10'' C CHANNEL

REV NO.

METAL PAN

DATE

DESCRIPTION

PRATT INSTITUTE | INT724

0' - 3"

PROJECT:

ATLANTIC AVE RESTAURANT

525 ATLANTIC AVE BROOKLYN NY DRAWING TITLE:

Staircase details

SEAL & SIGNATURE

1

Stair design 1 3" = 1'-0"

Three Dimensional Studies

DATE:

Issue Date

PROJECT NO. 17-724-04 DRAWING BY: Author CHK BY:

Checker

DRAWING NO.

A-301.02

2' x 4' ACT System 12' - 0" A.F.F.

PROJECT TEAM:

Lighting Fixture Schedule Fixture Designation

ADA Restroom 1 5

Location

Level

Recessed light

Level 1

Track Light

Level 1

4 A-600.00 2

Manufactur er Description

Lamp

LuxSpace Square

Philips

LED

Cluster Wall Washer

Lumenwerx LED

Type

Voltage

No IES Available

110V

CLUC10-WROLED-90-40

110V

Wattage 12W

9W

Count 9 3

Image

Model

Type Mark

DN572B L1 PSED-E RML Clusters L2 Wall Wash 10

INTERIOR DESIGNER NAME ADDRESS 1 ADDRESS 2 T: xxx.xxx.xxxx; F: xxx.xxx.xxxx

Family and Type 63_PHILIPS_LuxSpace Square_DN572B PSED-E RML: No IES Available Clusters Linear Wall Wash 10: CLUC10-WRO-LED-90-40

CLIENT: PRATT INSTITUTE - INTERIOR DESIGN - INT 724 Client Address 1 Client Address 2 Client Contact Info

Contact A - Title Contact A - Name Contact A - Address 1 Contact A - Address 2 Contact A - Phone

3

Level 1

Round Pendent

Lumenwerx LED

RIMRPDI-36-UL 110V O-LED-90-350040

9W

3

Rim Round L3 Pendant Direct/Indir ect 36

Rim Round Pendant Direct Indirect 36: RIMRPDI-36-ULO-LED-90-350040

Recessed light

Level 1

Shell Recessed

Lumenwerx LED

SHER-8-HLO-L ED-90-1400-40

110V

9W

16

Shell L4 Recessed 8

Shell Recessed 8: SHER-8-HLO-LED-90-1400-40

Recessed light

Level 2 Ceiling Plan

ArcForm

Philips

LED36S/83 RC660B 110V 0/W60L60 1xLED36S_830 MO-PC

20W

4

RC660B

63_PHILIPS_ArcForm (project SoftLight)_f: RC660B W60L60 1xLED36S_830 MO-PC

Pendent

Contact B - Title Contact B - Name Contact B - Address 1 Contact B - Address 2 Contact B - Phone

8' - 0"

L4

L4

L4

Contact C - Title Contact C - Name Contact C - Address 1 Contact C - Address 2 Contact C - Phone

Contact D - Title Contact D - Name Contact D - Address 1 Contact D - Address 2 Contact D - Phone

8' - 0"

Free Standing Seating

L5

2

L4

8' - 0"

L4

L4 7' - 1 11/32"

FINAL SUBMISSION 2' x 4' ACT System 9' - 0" A.F.F.

L4 0' - 0"

10' - 0"

0' - 0" 5' - 1 21/32"

L5

L5

7' - 7"

2' x 4' ACT System 12' - 0" A.F.F.

Manager Office L5

L1

8' - 0"

8' - 0"

2

L4

8' - 0"

L4

L1

Free Standing Seating

L3

L5

5

L1

L4

L1 1' - 7"

REV NO.

8' - 0"

L4 L1

8' - 0"

L3

L2

2' x 4' ACT System 9' - 0" A.F.F.

8' - 0"

L4

PRATT INSTITUTE | INT724

4' - 0"

L1

Build-in&Free-standing Seating

L2

4 8' - 0"

L3

L4

L4 L1

PROJECT:

ATLANTIC AVE RESTAURANT

525 ATLANTIC AVE BROOKLYN NY

L4

L1 6' - 0"

1' - 10 3/16"

1' - 1 1/2"

8' - 0"

10' - 0"

3' - 4 3/4"

DRAWING TITLE:

5' - 2"

9' - 8 1/4"

SEAL & SIGNATURE

-

-

-

Level 1 Ceiling Plan 1 1/4" = 1'-0"

DESCRIPTION

L4

8' - 0"

4' - 0"

L2

DATE

Level 2 Ceiling Plan 2 1/4" = 1'-0"

Reflected Ceiling Plan

DATE:

Issue Date

PROJECT NO. 17-724-04 DRAWING BY: Author CHK BY:

Checker

DRAWING NO.

A-400.00

PROJECT TEAM:

INTERIOR DESIGNER NAME ADDRESS 1 ADDRESS 2 T: xxx.xxx.xxxx; F: xxx.xxx.xxxx

CLIENT: PRATT INSTITUTE - INTERIOR DESIGN - INT 724 Client Address 1 Client Address 2 Client Contact Info

Contact A - Title Contact A - Name Contact A - Address 1 Contact A - Address 2 Contact A - Phone

Contact B - Title Contact B - Name Contact B - Address 1 Contact B - Address 2 Contact B - Phone

1 A-500.00

Contact C - Title Contact C - Name Contact C - Address 1 Contact C - Address 2 Contact C - Phone

Contact D - Title Contact D - Name Contact D - Address 1 Contact D - Address 2 Contact D - Phone

1 A-501.01

3

Level 1 Construction Annotate - Callout 2 1/2" = 1'-0"

1

Section 8 1/2" = 1'-0"

0' - 2"

2' - 0"

10' - 0"

FINAL SUBMISSION

2' - 6"

A-501.02

0' - 1"

1' - 2"

16' - 0"

0' - 4"

A-502.00

0' - 0' 4" - 6" 0' -0'6"-0'1"-0'6"-0'1"- 6" 1' - 3" 0' - 1"

2

3' - 10"

1

17' - 9"

0' - 2" 1' - 6" 0' - 2" 1' - 6" 0' - 2" 1' - 6" 0' - 2"

0' - 1"

REV NO.

DATE

DESCRIPTION

PRATT INSTITUTE | INT724

PROJECT:

ATLANTIC AVE RESTAURANT

525 ATLANTIC AVE BROOKLYN NY DRAWING TITLE:

Millwork Bar and Back bar Plan & Elevations

SEAL & SIGNATURE

DATE:

Issue Date

PROJECT NO. 17-724-04 DRAWING BY: Author CHK BY:

Checker

DRAWING NO.

A-500.00

PROJECT TEAM:

INTERIOR DESIGNER NAME ADDRESS 1 ADDRESS 2 T: xxx.xxx.xxxx; F: xxx.xxx.xxxx

2 A-501.01

CLIENT: PRATT INSTITUTE - INTERIOR DESIGN - INT 724 Client Address 1 Client Address 2 Client Contact Info

Sim

Contact A - Title Contact A - Name Contact A - Address 1 Contact A - Address 2 Contact A - Phone

Contact B - Title Contact B - Name Contact B - Address 1 Contact B - Address 2 Contact B - Phone

Section for bar 1 1" = 1'-0"

Contact C - Title Contact C - Name Contact C - Address 1 Contact C - Address 2 Contact C - Phone

Contact D - Title Contact D - Name Contact D - Address 1 Contact D - Address 2 Contact D - Phone

MARBLE TABLE 2'' FINAL SUBMISSION

NO DRIP NOSING

0' - 9 1/4"

1' - 10"

NO DRIP NOSING 0' - 1 11/16"

REV NO.

DATE

DESCRIPTION

PRATT INSTITUTE | INT724

PROJECT:

0' - 0 3/4"

ATLANTIC AVE RESTAURANT

525 ATLANTIC AVE BROOKLYN NY DRAWING TITLE:

Millwork Bar sections & Details 1

0' - 9"

0' - 4"

0' - 4"

0' - 5"

2' - 1 3/4"

MARBLE 3/4''

PLYWOOD 1/2'' MARBLE 3/4''

0' - 9 3/8" 0' - 1 1/4" 0' - 9 3/8"

0' - 0 3/4" 0' - 4 3/4" 0' - 0 3/4"

1' - 3"

0' - 1 11/16"

SEAL & SIGNATURE

DATE:

Issue Date

PROJECT NO. 17-724-04 DRAWING BY: Author CHK BY:

Checker

DRAWING NO.

2

Bar detail drawing 1 3" = 1'-0"

A-501.01

PROJECT TEAM:

INTERIOR DESIGNER NAME ADDRESS 1 ADDRESS 2 T: xxx.xxx.xxxx; F: xxx.xxx.xxxx

1 A-501.02

CLIENT: PRATT INSTITUTE - INTERIOR DESIGN - INT 724 Client Address 1 Client Address 2 Client Contact Info

Sim

Contact A - Title Contact A - Name Contact A - Address 1 Contact A - Address 2 Contact A - Phone

Contact B - Title Contact B - Name Contact B - Address 1 Contact B - Address 2 Contact B - Phone

Section for bar 2 1" = 1'-0"

Contact C - Title Contact C - Name Contact C - Address 1 Contact C - Address 2 Contact C - Phone

Contact D - Title Contact D - Name Contact D - Address 1 Contact D - Address 2 Contact D - Phone

MARBLE TABLE 2'' MARBLE 3/4

FINAL SUBMISSION

0' - 9 1/4"

1' - 10"

NO DRIP NOSING

0' - 7"

1' - 3"

0' - 1 3/4"

0' - 1 11/16"

REV NO.

DATE

DESCRIPTION

PRATT INSTITUTE | INT724

MDF WITH WOOD VENEER PLY WOOD 1/2

PROJECT:

1' - 11 1/8"

ATLANTIC AVE RESTAURANT

525 ATLANTIC AVE BROOKLYN NY DRAWING TITLE:

Millwork Bar sections & Details 2

0' - 1 1/4"

0' - 1 1/4"

SEAL & SIGNATURE

DATE:

Issue Date

1

Bar detail drawing 2 3" = 1'-0"

0' - 4"

PROJECT NO. 17-724-04

0' - 4"

2

DRAWING BY: Author CHK BY:

Checker

DRAWING NO.

A-501.02

PROJECT TEAM:

-1

"

BLACK BOARD 20*24

CLIENT: PRATT INSTITUTE - INTERIOR DESIGN - INT 724 Client Address 1 Client Address 2 Client Contact Info

Contact A - Title Contact A - Name Contact A - Address 1 Contact A - Address 2 Contact A - Phone

1'

-8 "

0'

INTERIOR DESIGNER NAME ADDRESS 1 ADDRESS 2 T: xxx.xxx.xxxx; F: xxx.xxx.xxxx

Contact B - Title Contact B - Name Contact B - Address 1 Contact B - Address 2 Contact B - Phone

MDF WITH WOOD VENEER

0' - 4"

0' - 1 3/4"

1' - 0"

2 A-502.00

Contact C - Title Contact C - Name Contact C - Address 1 Contact C - Address 2 Contact C - Phone

Contact D - Title Contact D - Name Contact D - Address 1 Contact D - Address 2 Contact D - Phone

Sim

FINAL SUBMISSION

Section for barback 1" = 1'-0"

MARBLE TABLE 2'' 0' - 2"

0' - 2"

2' - 5 5/8"

MDF WITH WOOD VENEER

1' - 3 5/8"

DATE

DESCRIPTION

PRATT INSTITUTE | INT724

PROJECT:

ATLANTIC AVE RESTAURANT

525 ATLANTIC AVE BROOKLYN NY DRAWING TITLE:

Barback detail drawing 1 1/2" = 1'-0"

0' - 4"

Millwork Back Bar sections & Details 0' - 4"

2

REV NO.

0' - 2"

1' - 1"

0' - 3 1/4"

1' - 7 31/32"

2' - 11 5/8"

1

SEAL & SIGNATURE

DATE:

Issue Date

PROJECT NO. 17-724-04 DRAWING BY: Author CHK BY:

Checker

DRAWING NO.

A-502.00

PROJECT TEAM:

INTERIOR DESIGNER NAME ADDRESS 1 ADDRESS 2 T: xxx.xxx.xxxx; F: xxx.xxx.xxxx

CLIENT: PRATT INSTITUTE - INTERIOR DESIGN - INT 724 Client Address 1 Client Address 2 Client Contact Info

Contact A - Title Contact A - Name Contact A - Address 1 Contact A - Address 2 Contact A - Phone

Contact B - Title Contact B - Name Contact B - Address 1 Contact B - Address 2 Contact B - Phone

Contact C - Title Contact C - Name Contact C - Address 1 Contact C - Address 2 Contact C - Phone

Contact D - Title Contact D - Name Contact D - Address 1 Contact D - Address 2 Contact D - Phone

FINAL SUBMISSION

REV NO.

DATE

DESCRIPTION

PRATT INSTITUTE | INT724

PROJECT:

ATLANTIC AVE RESTAURANT

525 ATLANTIC AVE BROOKLYN NY DRAWING TITLE:

CNC Milled Panel + Perspective/Axons

SEAL & SIGNATURE

DATE:

Issue Date

PROJECT NO. 17-724-04 DRAWING BY: Author CHK BY:

Checker

DRAWING NO.

A-503.00

PROJECT TEAM:

Other Partition Types

INTERIOR DESIGNER NAME ADDRESS 1 ADDRESS 2 T: xxx.xxx.xxxx; F: xxx.xxx.xxxx

2'' CONC SALB BACKERBD

CLIENT: PRATT INSTITUTE - INTERIOR DESIGN - INT 724 Client Address 1 Client Address 2 Client Contact Info

3/4 PLYWD SUBFL

1/4'' WHITE PAINT

1/4'' WHITE PAINT ADHISIVE 1/4''

24''*24''*1/2'' MARBLE TILE

WHITE PAINT

MDF

3/4'' GWB 3/4'' GWB

TILE

5/8'' PLYWD

24''*24''*1/2'' MARBLE TILE 1/4'' MTL HOOK

1/4'' MTL HOOK 2*1/2'' MTL STUD

5/8'' PLYWD

8''*8''*16'' CMU

WHITE PAINT

12''*8''*16'' CMU

Contact A - Title Contact A - Name Contact A - Address 1 Contact A - Address 2 Contact A - Phone

2''*4'' WD FRAME

Contact B - Title Contact B - Name Contact B - Address 1 Contact B - Address 2 Contact B - Phone

2''*10'' WD JOIST

W1

W2

W3

W4

W5

MTL WIRE

Contact C - Title Contact C - Name Contact C - Address 1 Contact C - Address 2 Contact C - Phone

5/8'' GWB

Contact D - Title Contact D - Name Contact D - Address 1 Contact D - Address 2 Contact D - Phone

FINAL SUBMISSION

12''*12''*1'' TERRAZZO FL

1/4'' BONDING AGENT

REV NO.

DATE

DESCRIPTION

PRATT INSTITUTE | INT724

24*24*1/2'' MARBLE TILE

2'' CONC SLAB BACKERBD 1/4'' MTL HOOK

3/4'' PLYWD SUBFL 5/8'' PLYWD

8''*8''*16 CMU

PROJECT:

ATLANTIC AVE RESTAURANT

525 ATLANTIC AVE BROOKLYN NY

2''*4'' WD FRAME DRAWING TITLE:

2 1/2'' MTL STUD

2''*10'' WD JOIST

Partition, Ceiling and Floor Details

SEAL & SIGNATURE

DATE:

Issue Date

PROJECT NO. 17-724-04 DRAWING BY: Author CHK BY:

Checker

DRAWING NO.

1

Wall Section Draft 1 1/2" = 1'-0"

A-504.00

PROJECT TEAM:

04

05

INTERIOR DESIGNER NAME ADDRESS 1 ADDRESS 2 T: xxx.xxx.xxxx; F: xxx.xxx.xxxx

Plumbing Fixture Schedule Manufactur ModelNum er ber Type Mark 01 SN-1 05

ø 5' - 0"

3' - 3"

5

02

Basin Basin Basin

201.0000.0 Satin 58

Xtech

1

Size 28’’*30’’*17’’ 26’’*22’’*7’’ 26’’*22’’*7’’

25 x 145 x 130 mm

Material

Family and Type

Keynote

Toilet-Domestic-3D: Toilet-Domestic-3D Sink-Single-2D: 26" x 22" Sanitary_Basins_Simas_Baden-Baden-Countertop-or-wall-hung-was: Default Xtech_FrankeSissonsLtd_TltRllHldrs_ToiletRoll Holder_BS677: BS677

Procelain Procelain Procelain

1.4301 Chrome Nickel steel V2A

CLIENT: PRATT INSTITUTE - INTERIOR DESIGN - INT 724 Client Address 1 Client Address 2 Client Contact Info

n/a n/a n/a

Contact A - Title Contact A - Name Contact A - Address 1 Contact A - Address 2 Contact A - Phone

n/a

5' - 3 1/4"

3' - 2"

3

Procelain 1 Procelain 1 Procelain 1

0564656 0564655 0564255

4 A-600.00 2

02

Co Finish unt

Contact B - Title Contact B - Name Contact B - Address 1 Contact B - Address 2 Contact B - Phone

1' - 6"

01

Contact C - Title Contact C - Name Contact C - Address 1 Contact C - Address 2 Contact C - Phone

4' - 7"

1

Level 1 Construction Annotate - Callout 1 1/2" = 1'-0"

Contact D - Title Contact D - Name Contact D - Address 1 Contact D - Address 2 Contact D - Phone

FINAL SUBMISSION

REV NO.

DATE

DESCRIPTION

PRATT INSTITUTE | INT724 3' - 6"

ATLANTIC AVE RESTAURANT

525 ATLANTIC AVE BROOKLYN NY

5' - 1" 1' - 0"

1' - 0"

Level 1 0' - 0"

Level 1 0' - 0"

DRAWING TITLE:

ADA Bathroom drawings & Plumbing Schedules

2' - 9 1/2"

2' - 3"

4' - 0"

4' - 0"

2' - 9 1/2"

2' - 3"

3' - 0"

3' - 0"

1' - 0"

1' - 0"

1' - 0" 2' - 3 3/4"

1' - 3 3/4"

Level 1 0' - 0"

3' - 0"

1' - 0" 4' - 0"

4' - 0"

1' - 0"

7' - 3"

1' - 0"

3' - 6"

3' - 6"

PROJECT:

Level 1 0' - 0" SEAL & SIGNATURE

2

Elevation 1 1/2" = 1'-0"

3

Elevation 2 1/2" = 1'-0"

4

Elevation 3 1/2" = 1'-0"

5

Elevation 4 1/2" = 1'-0"

DATE:

Issue Date

PROJECT NO. 17-724-04 DRAWING BY: Author CHK BY:

Checker

DRAWING NO.

A-600.00

PROJECT TEAM:

INTERIOR DESIGNER NAME ADDRESS 1 ADDRESS 2 T: xxx.xxx.xxxx; F: xxx.xxx.xxxx

CLIENT: PRATT INSTITUTE - INTERIOR DESIGN - INT 724 Client Address 1 Client Address 2 Client Contact Info

Contact A - Title Contact A - Name Contact A - Address 1 Contact A - Address 2 Contact A - Phone

Contact B - Title Contact B - Name Contact B - Address 1 Contact B - Address 2 Contact B - Phone

Contact C - Title Contact C - Name Contact C - Address 1 Contact C - Address 2 Contact C - Phone

Contact D - Title Contact D - Name Contact D - Address 1 Contact D - Address 2 Contact D - Phone

FINAL SUBMISSION

REV NO.

DATE

DESCRIPTION

PRATT INSTITUTE | INT724

PROJECT:

ATLANTIC AVE RESTAURANT

525 ATLANTIC AVE BROOKLYN NY DRAWING TITLE:

Images, perspectives view

SEAL & SIGNATURE

DATE:

Issue Date

PROJECT NO. 17-724-04 DRAWING BY: Author CHK BY:

Checker

DRAWING NO.

A-700.00