The SILTEC Locking Cable Tray is a new and unique tray, with which you can "weave" cables and tubing in and out, without the use of tools or of zip-ties for fastening. When cables lie free (unrestrained by zip-ties) in the tray, heat dissipation is improved, and cables are more easily accessed for cleaning, resulting in better cable hygiene.
SILTEC Locking Trays are especially suited for flexible cables and tubing, as they are removed and replaced at time of service, remodeling, etc.
LOCKING CABLE TRAYS
SILTEC Locking Trays are well suited for and quite easily customized to fit machinery and construction. By cutting out portions of the steel wires the trays can be bent in all directions. As a novelty, on types S20N and S21N, the cross wires are spaced further apart. To lock cables in these trays, some of the cross wires are bent over with the use of flat-nose pliers, thereby making zip-ties unnecessary.
All measurements in Inches.
1
DATA SHEET 1: 2
The SILTEC Locking Cable Tray is a new and unique tray, with which you can "weave" cables and tubing in and out, without the use of tools or of zip-ties for fastening. When cables lie free (unrestrained by zip-ties) in the tray, heat dissipation is improved, and cables are more easily accessed for cleaning, resulting in better cable hygiene.
SILTEC Locking Trays are especially suited for flexible cables and tubing, as they are removed and replaced at time of service, remodeling, etc.
LOCKING CABLE TRAYS
SILTEC Locking Trays are well suited for and quite easily customized to fit machinery and construction. By cutting out portions of the steel wires the trays can be bent in all directions. As a novelty, on types S20N and S21N, the cross wires are spaced further apart. To lock cables in these trays, some of the cross wires are bent over with the use of flat-nose pliers, thereby making zip-ties unnecessary.
All measurements in Inches.
1A + A1 + / - 0 06 Inches
2B + B1 + / - 0 06 Inches
DATA SHEET 1: 3
SILTEC Open Trays S25, S26, S27, S28 and S29 are designed to enable fastening of tubing and cable with cable clamps (pg. 8 in Standard Open Trays Brochure; pgs. 6 - 8 in Image Brochure).
The use of cable clamps creates space between cables, improving heat dissipation and fulfilling sharply increasing demands on hygiene as it applies to undesirable bacterial growth, deposits of combustible dust, etc.
OPEN CABLE TRAYS
Bends, curves, tees, and crosses are easily made by cutting out portions of tray steel wires (pgs. 12, 13 & 15 in Standard Open Tray Brochure; pgs. 4, 7 & 8 in Image Brochure).
SILTEC Open Trays are also engineered for easy and inexpensive side mounting using Mounting Bracket S45 or Mount S14.
All measurements in Inches
1A + A1 + / - 0 06 Inches
2B + B1 + / - 0 08 Inches
DATA SHEET 1: 4
SILTEC’s cable trays type S30, S35, S36, S37, S38 and S39 are traditional open trays with low sides
Trays S30 and S35 may be side mounted
Trays S36, S37, S38 and S39 are mounted on angle con-soles or similar.
OPEN CABLE TRAYS
SILTEC Cable Trays are versatile and easy to work with. The open design allows for easily accessible utilities. Round material is used throughout wherefore trays are gentle on installed tubing and cable.
All measurements in Inches
1A + A1 + / - 0 06 Inches
2B + B1 + / - 0 08 Inches
DATA SHEET 1: 5
SILTEC Compact Cable Trays are especially designed for machine builders. Trays S115, S116 and S125 - S133 range in width between 37 - 320 mm (1.5 - 12.6") while low sides are only 11 - 36 mm (0.4 - 1.4") tall. Steel wire diameter ranges between 3 - 5 mm (0.1 - 0.2"). With the exception of tray S125, all these trays are made with 2 bottom wires.
Mounting is normally done with screwed wall mounts, either consoles S65 - 68 or brackets S45, S45M, S145, S145M, S180 & S181, & S147 with bendable tongues, or onto equipment or existing structures using Polypropylene mounts S14, S14M & S330, splice plates S40B and S41B, pipe mounts S160 - S164 and aforementioned mounts.
COMPACT CABLE TRAYS
SILTEC cable trays are versatile and easy to work with. The open design allows for easily accessible utilities. Round material is used throughout wherefore trays are gentle on installed tubing and cables.
SILTEC Compact Cable Trays are used predominantly in:
• Food industry
• Sweet foods, candy & pastry industries
• Chemical & pharmaceutical industries
• Dairies
• Bottling plants
• Breweries
All measurements in Inches
1A + A1 + / - 0.06 Inches
2B + B1 + / - 0 06 Inches
DATA SHEET 1: 6
SILTEC Heavy Duty Cable Trays S428 - S446 range in width between 100 - 900 mm (4 - 36") while sides are all 100 mm (4") tall Steel wire diameter is 5 mm (0.2"). Mounting is normally done with Shelf Brackets S275 - S278, Center Mounts S256 - S260, and Brackets S45, S45M, S80 & S81 with bendable tongues, fastened to Ceiling Hanger S271 or onto existing structures.
SILTEC cable trays are versatile and easy to work with. The open design allows for easily accessible utilities.
HEAVY DUTY CABLE TRAYS
Round material is used throughout wherefore trays are gentle on installed tubing and cable.
SILTEC Heavy Duty Cable Trays are used predominantly in:
• Food industries
• Sweet food, pastry & candy industries
• Chemical and pharmaceutical industries
• Dairies
• Bottling plants
• Breweries
S440 3.94 4.25 1.18 1.57
All measurements in Inches
1A + A1 + / - 0.08 Inches
2B + B1 + / - 0 08 Inches
DATA SHEET 1: 7
SILTEC Open Cable Trays S30M-X, S30-X, S35-X and S36-X with C-Profile, have sides that are bent in at the top. With their slightly closed design, these trays prevent cables from sliding out, making them a suitable alternative to Locking Trays S20 - S123. Steel wire diameters are 4 and 5 mm (0.15” - 0.2").
Mounting is normally done with Weld Brackets S52 & S63, or Screwed Angle Brackets S65 - S68, Shelf Brackets S279S280 and Mounting Brackets S153 - S154, S45, S45M, S145M, S80 - S81 & S180 - S181 with bendable tongues. Mounting can also be done on existing structures using Splice Plates S40B and S41B, Pipe Mounts S160 - S164 and aforementioned screwed mounting brackets.
OPEN C-PROFILE CABLE TRAYS
SILTEC cable trays are versatile and easy to work with. The open design allows for easily accessible utilities. Round material is used throughout wherefore trays are gentle on installed tubing and cable.
SILTEC Open C-Profile Cable Trays are used predominantly in:
• Food industries
• Sweet food, pastry & candy industries
• Chemical and pharmaceutical industries
• Dairies
• Bottling plants
• Breweries
All measurements in Inches
1A + A1 + / - 0 06 Inches
2B + B1 + / - 0 08 Inches
DATA SHEET 1: 8
SILTEC Heavy Duty Cable Trays S235 - S240 are especially designed for very heavy loads over spans up to 6000 mm (20 feet). Width ranges between 100 - 600 mm (4 - 24") while sides are all 100 mm (4") tall. Steel wire diameter is 5 mm (0.2").
The sides of these trays are reinforced with a 5 mm (0.2") steel wire ran in a zig-zag pattern to prevent twisting and bending. This is further supported by the double steel wires at tray bottom and along top of the sides. Mounting is normally done with shelf brackets S275 - S280 or center mounts S256 - S260, fastened to ceiling hanger S271 or onto walls or existing structures.
HEAVY DUTY CABLE TRAYS
Round material is used throughout wherefore trays are gentle on installed tubing and cables. SILTEC Heavy Duty cable trays are used predominantly in:
• Food industries
• Sweet food, pastry & candy industries
• Chemical and pharmaceutical industries
• Dairies
• Bottling plants
• Breweries
All measurements in Inches
1A + A1 + / - 0 08 Inches
2B + B1 + / - 0 08 Inches
DATA SHEET 3: 1
SILTEC Mounting Bracket S45 is designed to enable horizontal as well as vertical installation of trays S20 through S35.
S45 has two oblong intersecting holes, each 7 x 12 mm (0.3” x 0.5”) for securing to wall, ceiling hanger or other construction.
After the cable tray has been inserted into the bracket, it is locked into place by bending over tongues. It can be unlocked again in case of installation revisions.
MOUNTING BRACKET - S45
SILTEC Mounting Bracket S45 is made of 2 mm (0.08”) steel plate and has a cut-out in the back for minimized contact surface and improved hygiene. Better hygiene is also achieved with a bracket design that uses a minimum of horizontal surfaces.
Hygienic mounting brackets are available for all trays (see Data Sheets 3:3 and 3:4).
DATA SHEET 3: 2
SILTEC Angle Consoles S65 - S68 are made of 2 mm (0.08”) steel plate. The end flange has two oblong holes, 10 x 15 mm (0.4” x 0.6”) for fastening of the console to wall, ceiling hangers or other construction.
Oblong holes at top of the console for mounting of the cable tray allow for adjustments of tray position to make up for uneven mounting surfaces.
ANGLE BRACKETS
Consoles are designed for roughly 30 - 35 mm (1.2” – 1.4”) clearance between inside of tray and wall, with room for adjustments.
Cable tray is secured to console using either two S90 Bolt Kits or two S90H J-Bolt Kits together with one S87 Splice Bracket.
All measurements in Inches
DATA SHEET 3: 3
SILTEC Brackets for Optimal Hygiene are available for screwassembly or for welding. Made of 316 acid-resistant stainlesssteel plate, and tailored to each tray, these brackets are recommended wherever highest level of hygiene is desired.
After the cable tray has been inserted into the bracket, it is locked into place by bending over tongues. It can be un-locked again in case of installation revisions.
BRACKETS FOR OPTIMAL HYGIENE *SCREW - MOUNTED*
Brackets have a cut-out in the back for minimized contact sur-face and improved hygiene. Better hygiene is also achieved with a bracket design that uses a minimum of horizontal sur-faces.
All measurements in Inches
DATA SHEET 3: 4
SILTEC Brackets for Optimal Hygiene are available for screwassembly or for welding. Made of 316 acid-resistant stainlesssteel plate, and tailored to each tray, these brackets are recommended wherever highest level of hygiene is desired.
After the cable tray has been inserted into the bracket, it is locked into place by bending over tongues. It can be un-locked again in case of installation revisions.
BRACKETS FOR OPTIMAL HYGIENE *WELDED*
Brackets have a cut-out in the back for minimized contact sur-face and improved hygiene. Better hygiene is also achieved with a bracket design that uses a minimum of horizontal surfaces.
3 66 1
0
S21 S22 S26 S27 and S30
0
S28 and S29 S63 4 33 1 02 0 91 0 06 S35 S36 S37 and S38 All measurements in Inches.
DATA SHEET 3: 5
SILTEC Angle Consoles S275 - S280 are made in 315 acidresistant stainless steel of 2 mm (0.08”) with 4 mm (0.16”) backing flange.
These consoles are required for cable ladders and trays with side reinforcement, but can also be used with lighter duty cable trays.
Oblong holes at top of the console for mounting of the cable tray allow for adjustments of tray position to make up for
ANGLE BRACKETS – HIGH WEIGHT CAPACITY
uneven mounting surfaces. Consoles are designed for roughly 30 - 35 mm (1.2” - 1.4”) clearance between inside of tray and wall, with room for adjustments.
Cable tray is secured to console using either two S90 Bolt Kits or two S90H J-Bolt Kits together with one S87 Splice Bracket.
For mounting cable ladders and cable trays with side reinforcement type:
All measurements in Inches
DATA SHEET 4: 1
SILTEC Ceiling Hanger S71 made of acid-resistant 316 stainless steel, can be extended 1000 mm (39.4”) using Extender S72, increasing distance A to 1450 mm (57.1”).
Top flange tilts 45 degrees (Y) to each side and tilting position is fixed with a bolt.
CEILING HANGER S71
Top flange and pendant are fixed at 90 degrees with bolt mounted in position X.
Hanger S71 accepts brackets (S45 and S65 - S68) on three sides.
Two S90 Bolt Kits are used per bracket.
All measurements in Inches
DATA SHEET 5: 1
SILTEC Ceiling Hanger S73 made of acid-resistant 316 stainless steel is designed for center-mounting of cable trays together with brackets S45 and S45M. A less expensive option to Ceiling Hanger S71 (Data Sheet 4:1), Ceiling Hanger S73 does not allow for mounting of trays on sides of hanger.
CEILING HANGERS
Top angle bracket tilts to required angle, and can be turned to fit different mounting configurations.
All measurements in Inches
DATA SHEET 6: 1
SILTEC Divider S85 made of acid-resistant 316 stainless steel is used with Standard Open, Compact and Heavy-Duty trays.
1 mm (0.08”) material thickness gives good stability and protection against cable damage.
With its simple construction without bends and folds this divider notably meets the high requirements for hygiene within:
• Food industry
• Sweet food, pastry & candy industries
• Chemical and pharmaceutical industries
• Dairies
• Bottling plants
• Breweries
All measurements in Inches.
DATA SHEET 6: 2
SILTEC Flat Tray Covers S92 - S96 and S93W made of 304 and 316 stainless steel snap-fit firmly onto trays S30 - S38
Flat Tray Covers are made with 1 mm (0.08”) material thickness and come in 2000 mm (7.87”) lengths.
in Inches.
DATA SHEET 6: 3
SILTEC Pitched Tray Covers S91 - S96 and S93W made of 304 stainless steel snap-fit firmly onto trays S30M - S38. Liquids run off pitched profile, making for easier cleaning.
Pitched Tray Covers are made with 1 mm (0.08”) material thickness and come in 2000 mm (7.87”) lengths.
