Lumbermens November 2022 Magazine

with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703 EDGERS & GANGS Brewco Saws - Two Brewco Saws in excellent condition. Runs great. Item ID 13644. Sam x702

FIREWOOD PROCESSORS

2010 Shop Built Wood Processor -It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot

chain conveyer, 8 way splitter, on 20,000lb goose neck trailer. Item ID 13916. Austin x703

Best Value Portable Log Splitter -Small manufacturer in PA has made the best valued log splitter. Handles logs up to 32”. Uses 13HP Honda motor. Manual start but electronic option is available. Has Log Lift. Uses 4-way wedge adjustable to single two way. Great Value! PA. Item ID 12062. Sam x702 Firewood Processor - This is a homemade processor with a 10’ log deck. Has a hydraulic grapple, chain and kicker that all runs off of a 4 cylinder Mercedes power unit. Has a 4’ chain saw that kicks

off onto a conveyor. This is a very well built processor. Item ID 13820. Sam x702

Firewood Processor - This is a Chomper Model 16 PDA automatice firewood processor with John Deere power unit with low hours. Control panel includes tach, oil pressure, water temp and amp gauges. Cuts logs up to 16”. One owner and comes with all manuals and receipts. Purchased new for $32,500. Item ID 13865. Sam x702

LOGGING EQUIPMENT

1999 Bandit 1900 Tracked Disc Chipper - Cat Under Carriage at 50% or better. 475 hp Cummins Diesel. 7500 Hours. One owner. Well maintained. Item ID 13294. Sam x702

2004 Bandit Beast Model 46803412 Caterpillar Diesel engine with 850 HP. 5300 hrs. Mill in good condition. Just finished 10 Acre clearing job, ready to work! Remote control. Big production

capacity!. Item ID 13421.

BARKO

1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous grapple, 5,000 original hours. (excellent condition.). Item ID 13238. Chris x700

x702

1995 Barko 775 B Feller Buncher -Pumps recently redone. 400 hrs on injection pump. always started good. in good working order. 22in kohing head. head works great. Item ID 13185. Sam x702

1999 Barko 160D - new engine with approximately 1500 hours. Hour meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks. Item ID 13694.

value with low at hours at 3,500. 5.9 CUMMINS continuous grapple. Runs Great!. Item ID 13740.

Barko 275 -

option is available. Has Log Lift. Uses 4-way wedge adjustable to single two way. Great Value! PA. Item ID

Firewood Processor - This is a homemade processor with a 10’

deck. Has a hydraulic grapple, chain and

that all runs off of a 4 cylinder Mercedes power

Has a 4’ chain

automatice firewood processor with John Deere power unit with low hours. Control

that

includes tach,

One

pressure, water temp and

Cuts

up to

with

manuals and receipts. Purchased new for $32,500. Item ID 13865. Sam x702

LOGGING EQUIPMENT

BANDIT

1999 Bandit 1900 Tracked Disc Chipper - Cat Under Carriage at 50% or better. 475 hp Cummins Diesel. 7500 Hours. One owner. Well maintained. Item ID 13294. Sam x702 2004 Bandit Beast Model 46803412 Caterpillar Diesel engine with 850 HP. 5300 hrs. Mill in good condition. Just finished 10 Acre clearing job, ready to work! Remote control. Big production

capacity!. Item ID 13421. Sam

Lumberman's Exchange is published monthly by

Publishing, P.O. Box 1916, Columbia, TN 38402. All rights reserved. All editorial/ advertorial submissions are used at the discretion of the publisher and may be edited for purposes of clarity and space. Although all efforts have been made to ensure accuracy of content submitted by advertisers and writers, the Lumberman's Exchange, its principles and associates, are not held liable for errors or omissions. Reproduction, in whole or part, is prohibited without written consent.

in Lumbermens™ are the property of advertiserQs. Lumbermens ™ owns material typeset and/or designed by Lumbermens ™ and reserves the right to its use outside of Lumbermens™. Lumbermens™ will exercise every precaution in writing, designing, and printing material contained within.

shall not

liable for omissions or typographical errors.

CABLE SKIDDERS

1997 TIMBERJACK 240C

1997 Timberjack 240C with powershift transmission, hard to find skidder that still has low hours on it, only around 6500 original hours. Has gearmatic winch, good pins and bushings, and no bad leaks anywhere.

Call for more info.

Item ID 100096. Austin x703

JOHN DEERE 440C'S PACKAGE DEAL

Up for sale are two John Deere 440C Cable skidders, one is in great shape, winch just totally rebuilt and and working daily. The other has the transmission out of it, the trans has been rebuilt,

but has not been put back in the skidder. Call for more info.

Item ID 100094. Austin x703

2014 JOHN DEERE 640H

2014 Model John Deere 640H cable skidder with 1300 original hours, skidder is in mint condition, its a one owner machine, excellent rubber, tight, and clean as a whistle.

Call for more information.

Item ID 100091. Austin x703

79' TIMBERJACK 225D

13428 Victory Ln. // PO Box 124 Adams Center, NY 13606

79’ Timberjack 225d Has new 4BT Cummins engine with 1000 hours on it. New brakes

New tires on back New parking brake Tight center section

Really tight skidder for the age.

Also Comes with another set of 23.1 tires and a brand new set of chains.

Item ID 100087. Austin x703

‘05 Gehl CTL 70

Item ID: JW-986495

97' TIMBERJACK 240C

Contact: J Williams Ph: (888) 401-6367 x701

97' JOHN DEERE 640G

1997 model John Deere 640G, pulling wood daily, has new rearend, new center section, and new hydraulic pump in it. Motors been done couple years ago, call for more info.

Item ID 100070. Austin x703

CAT 518 CABLE

80%. Call for more information Item ID 99852. Austin x703

DYNAMIC CHIPPERS

PRECISION HUSKY CHIPPER

with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703

Brewco Saws - Two Brewco Saws in excellent condition. Runs great. Item ID 13644. Sam x702

FIREWOOD PROCESSORS

2010 Shop Built Wood Processor

-It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot

Contact: J Williams Ph: (888) 401-6367 x701

1997 Timberjack 240C has freshly rebuilt 4BT cummins engine with 50 hours on it, as well as rebuilt 4 speed new process transmission. Comes with 23.1 tires at around 50%.

chain conveyer, 8 way splitter, on 20,000lb goose neck trailer. Item ID 13916. Austin x703

Call for more info.

Item ID 100076. Austin x703

84' JOHN DEERE 440C

1984 John Deere 440C has freshly rebuilt engine, tight pins and bushings, as well as all new hoses. No leaks, woods ready skidder. Call for more info.

Item ID 100075. Austin x703

Best Value Portable Log Splitter -Small manufacturer in PA has made the best valued log splitter. Handles logs up to 32”. Uses 13HP Honda motor. Manual start but electronic option is available. Has Log Lift. Uses 4-way wedge adjustable to single two way. Great Value! PA. Item ID 12062. Sam x702

84' JOHN DEERE 540B

1984 John Deere 540B just had the winch completely rebuilt, no motor or trans work recently, but both are strong and don't bur any oil. Call for more info.

Item ID 100074. Austin x703

Firewood Processor - This is a homemade processor with a 10’ log deck. Has a hydraulic grapple, chain and kicker that all runs off of a 4 cylinder Mercedes power unit. Has a 4’ chain saw that kicks

‘13 KMC 2500 Track Skidder

Item ID: 14078

Contact: Austin Ph: (888) 401-6367 x703

Early 90's Cat 518 cable skidder, has cat winch, and cat motor in it in good shape. Tight center section, no leaks on it. Comes with decals if interested. Serial number is 94U model. Tires are size 34.5. Woods ready.

Item ID 33681. Austin x703

DOZERS WITH WINCHES

off onto a conveyor. This is a very well built processor. Item ID 13820. Sam x702

JOHN DEERE 750K

2014 model John Deere 750K currently has 3700 hours on it, equipped with winch, screens, limb risers. Undercarriage is 60%, well maintained, clean cab, good heat/ac. Call for more info.

Item ID 100053. Austin x703

JOHN DEERE 750J

Firewood Processor - This is a Chomper Model 16 PDA automatice firewood processor with John Deere power unit with low hours. Control panel includes tach, oil pressure, water temp and amp gauges. Cuts logs up to 16”. One owner and comes with all manuals and receipts. Purchased new for $32,500. Item ID 13865. Sam x702

2011 John Deere 750J has 4200 original hours, enclosed cab with heat/air, strong winch. Undercarriage is around 80%. Working until sold.

LOGGING EQUIPMENT

BANDIT

Item ID 100015. Austin x703

1999 Bandit 1900 Tracked Disc Chipper - Cat Under Carriage at 50% or better. 475 hp Cummins Diesel. 7500 Hours. One owner. Well maintained. Item ID 13294. Sam x702

JOHN DEERE 650H

2003 John Deere 650H has around 8000 frame hours, Undercarriage is around 60%, has full forestry package with winch. Dozer was never logged with until this past year.

Item ID 99876. Austin x703

JOHN DEERE 650G

90's model John Deere 650G Long Track Full forestry Dozer with winch. undercarriage is at about

2004 Bandit Beast Model 46803412 Caterpillar Diesel engine with 850 HP. 5300 hrs. Mill in good condition. Just finished 10 Acre clearing job, ready to work! Remote control. Big production

‘95 John Deere C6 Tree Farmer

Item ID: 13920

They put it to work, bought brand new in 2013 -66 inch -8 knife -Bottom discharge -Extra parts come with it (worth about $5,000) -Owner is done with project and so selling it -Machine is as good as new, everything works on it.

Contact: Austin Ph: (888) 401-6367 x703

Item ID 100116. Joe x709

BANDIT GRINDER - CHIPPER

capacity!. Item ID 13421. Sam x702

PRICE REDUCED $165,000

BARKO

1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous grapple, 5,000 original hours. (excellent condition.). Item ID 13238. Chris x700

1995 Barko 775 B Feller Buncher -Pumps recently redone. 400 hrs on injection pump. always started good. in good working order. 22in kohing head. head works great. Item ID 13185. Sam x702

This is a 2017 Bandit 3680 875 hp CAT bought it new 10-17 it has 1000hrs+\- Still running it some. It has the new design 30 tooth mill and also had a new tail shaft and new anvil and gate. Also has a set of 3” baffled screens for it that only have about 30hrs on them. This is a strong tier 2 machine owner operated they are selling because they upgraded to a 1200hp machine, there is nothing wrong with this machine and it is ready to work! If sold they can transport anywhere in Florida or to the FL state line to reduce transportation cost for the buyer. You won’t find a grinder in this good of shape anywhere.

Item ID 72593. Austin x703

FELLER BUNCHERS

1999 Barko 160D - new engine with approximately 1500 hours. Hour meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks. Item ID 13694. Sam x702

08' JD 843J ($49.5K)

94 Barko 275 - Excellent value with low at hours at 3,500. 5.9 CUMMINS continuous grapple. Runs Great!. Item ID 13740. Sam x702

BELL

4 Brand new tires, 28L’s -Enclosed CAB -Center section is tight, too -A/C - Heat works no problem -2yrs owner, getting out of logging, going a different route -Cutter is ready to go to work, tight machine -Everything works as it should, really, really good cutter

1990 Bell Super T - This Bell has a brand new Duetz engine. Lever control, 33” bar, pump and tranny

Item ID 100122. Joe x709

13' JOHN DEERE 643K

2013 John Deere 643K with 6300 original hours, joystick control. Cab has heat/air, tires have good tread at 30.5 size. Cutter is in excellent shape, well maintained. Call for more info.

Item ID 100115. Austin x703

07' TIMBCO 445EXL

2007 Timbco 445 Exl with 8000 original hours, cutter has new chains, and sprockets. UC is around 80%. Barsaw Head will rotate 45 degrees, but is plumbed for 360 degree rotation. Cutter is in great

shape and is woods ready. Call for more info

Item ID 100104. Austin x703

15' TIGERCAT 724G

2015 Tigercat 724G has 8500 original hours, has the big hardwood head on it, cutter has been well maintained and is turn key ready. Call for more info.

Item ID 100101. Austin x703

96' CAT 312 TRACK BUNCHER

1996’ Cat 312 Feller Buncher with Timbco head. Buncher has 8000 original hours with no oil

leaks. Tracks are good, head was re-bearinged, with new bushings. Rails 95% on one side, 40% on the other. Brand new AC unit and has good heat. Complete service was just completed 20 hours ago. Also Comes with 24” bucket. Call for more info. Item ID 100088. Austin x703

‘16 Halverson H140 Skidsteer (DEMO)

Item ID:

'05 JD 643H ($29.5K)

Contact: J Williams Ph: (888) 401-6367

Hours Meter Reading: 8324 -John Deere bunching head -Tires size: 28L-26 Tires -A/C - heat both work good -Center section is tight -Pins & bushings are good -It has a new saw disk -Kept really,

really well. Good cutter.

Item ID 100072. Joe x709

TIMBCO 425C

with 1700

Brewco Saws - Two

2010 Shop Built Wood Processor -It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot

KMC 2500 Track

Item ID: 14078

Contact: Austin Ph: (888) 401-6367

off onto a conveyor. This is a very well built processor. Item ID 13820. Sam x702

Firewood Processor - This is a Chomper Model 16 PDA automatice firewood processor with John Deere power unit with low hours. Control panel includes tach, oil pressure, water temp and amp gauges. Cuts logs up to 16”.

‘93 Barko 180B

Item ID: 14077

Contact: Austin Ph: (888) 401-6367

2003 Timbco 425C has around 10900 frame hours, new teeth for the head, 8.3 cummins motor, one side final drive has been replaced, the other side one final drive is a little weak, still running fine but starting to show some wear. Overall buncher is in good shape. Call for more info.

Item ID 100028. Austin x703

CAT 563C

2016 Cat 563C Has right around 6400 frame hours

Joystick control New style bunching head In great shape everything works like it should.

‘95 John Deere C6 Tree Farmer

Item ID 99970. Austin x703

Item ID: 13920

Contact: Austin Ph: (888) 401-6367 x703

445B

98’ Timbco 445B auto leveling, new undercarriage, has hot saw head, and new 8.3 cummins engine in it. Head is in good shape, no cracks in the disc, and new teeth.

capacity!. Item ID 13421. Sam x702 BARKO

1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous

Item ID 99934. Austin x703

on injection pump. always started good. in good working order. 22in

1999 Barko 160D - new engine with meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks. a brand new Duetz engine. Lever control, 33” bar, pump and tranny

JOHN DEERE 753J

2014 John Deere 753j buncher well maintained. 10,826hrs great shape undercarriage at 50% Main boom and stick boom have been updated with strengthening plates 1,000hrs ago. New Stickboom cylinder. Heads is in good shape. Everything is tight and dry.

Item ID 99917. Austin x703

14' TIGERCAT 720E

2014 Tigercat 720E has 10000 frame hours, and new reman motor with 150 hours on it, with receipts. Cutter is tight,

dry, and a clean machine inside and out. Also has new style joysticks and new saw pump. Needs nothing to get in the woods.

Item ID 99916. Austin x703

JOHN DEERE 643K

2012 John Deere 643K with 6500 hours just had new cutting edge installed. This cutter has been garage kept half of its life and is very clean inside and out, meticulously maintained with absolutely no issues. Comes with brand new 43" wide tires for front axle,

along with good 28L tires with original rims. Call for more pics and info.

Item ID 99905. Austin x703

JOHN DEERE 753J

grab arms are in good working order. Heat, air conditioning, & lights all work.

Item ID 99902. Austin x703

JOHN DEEERE 643G

‘93 Barko 180B

with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703

Brewco Saws - Two Brewco Saws in excellent condition. Runs great. Item ID 13644. Sam x702

2010 Shop Built Wood Processor

-It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot

‘16 Halverson H140 Skidsteer (DEMO)

Item ID: JW-909632

Contact: J Williams Ph: (888) 401-6367 x701

2013 John Deere 753J Feller Buncher with a FR21B Felling Head. It has 8500 hours, runs and starts good, resealed gear box, strong hydraulics and drive, new saw pump. Boom has tight pins and bushings, Bigfoot undercarriage will need to be replaced soon, and will also need a new saw disc soon. It has 24" single grouser pads.

well

Item ID: 14077

Contact: Austin Ph: (888) 401-6367 x703

1996 model John Deere 643G feller buncher its a one owner machine, has good hydraulics, it starts, runs, and cuts as it should. Call for more info.

Item ID 99897. Austin x703

JOHN DEERE 843J

2008 model John Deere 843J machine is tight, dry, and works perfect, running everyday, size 28L tires. Cab has heat/ ac. Frame hours are right at 10,000.

Item ID 99879. Austin x703

‘95 John Deere C6 Tree Farmer

Item ID: 13920

JOHN DEERE 643K

Contact: Austin Ph: (888) 401-6367 x703

2013 model John Deere 643K currently has 8600 hours on it, buncher is tight and dry, with no leaks or blow by. Averaging 30-40 loads a week. Call for more info.

capacity!. Item ID 13421. Sam x702 BARKO

Item ID 99866. Austin x703

1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous

on injection pump. always started good. in good working order. 22in

1999 Barko 160D - new engine with meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks. a brand new Duetz engine. Lever control, 33” bar, pump and tranny

BELL ULTRA T

1997 Bell Ultra T has new Deutz engine in it with 15 hours on it. Tracks and undercarriage are in excellent condition. Cab has AC and joystick control. Woods ready. Video available if interested

Item ID 99865. Austin x703

HYDRO AX 721E

around and is 100% ready to go to work.

Item ID 99826. Austin x703

CAT 573

2006 model which is the first year Hydro ax bought Cat so technically it is a Hydro ax cutter with Cat decals, but it has 8700 hours on it, and is in real good shape. Woods ready.

80. has new rails, rollers, and sprockets, Hardly any leaks around pump system, ac just recharged. working daily. Call for more pics and info. Item ID 98053. Austin x703

tires on it. Call for more info. Item ID 100093. Austin x703

JOHN DEERE 1010D

‘93 Barko 180B

‘16 Halverson H140 Skidsteer (DEMO)

CAT 563C

Item ID: JW-909632

Contact: J Williams Ph: (888) 401-6367 x701

2004 Hydro ax 721 E is in excellent condition, it has only had two owner/ operators its entire life. It has a 8.3 cummins engine, and the machine itself has around 6000 original frame hours. New upgrades include a new windshield, new batteries, and new blades and teeth on the mowing deck. There are no leaks, and all of the pins and bushings are very tight. Unit Includes a bunching head and mower deck. The tires are size 28L and are basically new. And it includes a set of chains for the front tires. Machine is really in excellent shape all

Item ID 59580. Austin x703

JOHN DEERE 848L

2015 model with 3600 hours in excellent condition. Call for more pictures and information.

Item ID 83128. Austin x703

HYDRO AX 411

411 Hydro ax comes with log forks, a morbark sheer, and a 8 foot mower deck. All is work ready.

Item ID 98954. Austin x703

Victory Ln. // PO Box 124

Center, NY

TIMBCO 425D

1995 Timbco 425D has around 10000 frame hours. Head is a quadco 22" hotsaw, 40 degree tilt, UC % is around

2016 Cat 563C wheeled buncher with 2010 original hours, size 28L tires, in excellent condition inside and out.

Item ID 2594. Austin x703

FORWARDERS

TIMBERJACK 610

2000 model 610 Timberjack forwarder with joystick control, 13000 frame hours. Cummins engine, brand new rubber. Has good AC/Heat. Loading logs daily.

John Deere 4850

Item ID: Contact: Ph: (888) 401-6367

with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703

EDGERS & GANGS

Brewco Saws - Two Brewco Saws in excellent condition. Runs great. Item ID 13644. Sam x702

FIREWOOD PROCESSORS

2010 Shop Built Wood Processor -It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot

‘05 Gehl CTL 70

Item ID: JW-986495

Contact: J Williams Ph: (888) 401-6367 x701

but electronic option is available. Has Log Lift. Uses 4-way wedge adjustable to single two way. Great Value! PA. Item ID 12062. Sam x702 Firewood Processor - This is a homemade processor with a 10’ log deck. Has a hydraulic grapple, chain and kicker that all runs off of a 4 cylinder Mercedes power unit. Has a 4’ chain saw that kicks

‘13 KMC 2500 Track Skidder

Item ID 100095. Austin x703

FRANKLIN 132

Item ID: 14078

Contact: Austin Ph: (888) 401-6367 x703

1994 model Franklin 132 forwarder with 6500 original hours on it, has cummins engine, clean cab with new glass all around. 12' 8'' log bunk. Heat/air, and good 23.1

off onto a conveyor. This is a very well built processor. Item ID 13820. Sam x702

Firewood Processor - This is a Chomper Model 16 PDA automatice firewood processor with John Deere power unit with low hours. Control panel includes tach, oil pressure, water temp and amp gauges. Cuts logs up to 16”. One owner and comes with all manuals and receipts. Purchased new for $32,500. Item ID 13865.

LOGGING EQUIPMENT

BANDIT

1999 Bandit 1900 Tracked Disc Chipper - Cat Under Carriage at with 850 HP. 5300 hrs. Mill in good condition. Just finished 10 Acre clearing job, ready to work! Remote control. Big production

Item ID: 14077

Contact: Austin Ph: (888) 401-6367 x703

2005 John Deere 1010/D Has 14000 frame hours Dry machine, with good pumps. In the woods working now. It comes with two sets of tires (23inch & 43s) Injector pump (Brand New) Turbo Injectors (Brand New) Ready for the Woods!

Item ID 100022. Austin x703

VALMET 644

‘95 John Deere C6 Tree Farmer

Item ID: 13920

Contact: Austin Ph: (888) 401-6367 x703

capacity!. Item ID 13421. Sam x702

BARKO

2002 Valmet 644 forwarder in excellent condition it has a cummins engine with a powershift transmission, joystick controls, and extenda boom. Recent work includes: new center bearing redone, brand new rack, new main pump, new valve bank, new brake pump up by the motor, and new clam cylinder. Has new 23.1 tires on the back. Overall very clean and in great shape.

Item ID 99837. Austin x703

1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous grapple, 5,000 original hours. (excellent condition.). Item ID 13238. Chris x700

1995 Barko 775 B Feller Buncher -Pumps recently redone. 400 hrs on injection pump. always started good. in good working order. 22in kohing head. head works great. Item ID 13185. Sam x702

1999 Barko 160D - new engine with approximately 1500 hours. Hour meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks. Item ID 13694. Sam x702

94 Barko 275 - Excellent value with low at hours at 3,500. 5.9 CUMMINS continuous grapple. Runs Great!. Item ID 13740. Sam x702

BELL

1990 Bell Super T - This Bell has a brand new Duetz engine. Lever control, 33” bar, pump and tranny

VALMET 840.4

fuel pump installed.

Item ID 79249. Austin x703

Tree that Started it All!

2009 Valmet 840.4 6 wheel forwarder. Sisu 6 cylinder diesel motor. 28L size front tires at 75%, 710/45X26.5 rear tires at 60%. fuel fired diesel heater. CRF8.1 Cranab loader, G36 Grapple with protec system. Recent work includes brand new hydro stats, along with new drive motor and new injection pump. Running gears have been gone through from one end to the other. Not a leak on this machine. Also had new

TIMBERKING 458

2005 Timberking 458 forwarder with 17,750 frame hours, had new engine installed 1000 hours ago, new super grip grapple 1000 hours ago as well. Very well maintained and straight machine, working daily.

NY STATE WOODSMEN'S FIELD D AYS

Fri, 18 August - S un, 20 August Boonville, New York www.starwebhosting.net/woodsmen/

SOUTHWEST FOREST PRODUCTS EXPO

Fri, 25 August - Sat, 26 August Hot Springs, Arkansas www.arkloggers.com

frame hours, has new trunnion, has new rear bogie brakes that were installed last spring. New loader mast put on a year ago, comes with 1 set of ice chains, and 1 set of bear paws, and 1 set of tracks. Tires are 600's rears are 80% fronts are 40% comes with extra hoses, and extra lights.

Item ID 9770. Austin x703

Item ID 171. Austin x703

VALMET 840.2 FORWARDER

2005 Valmet 8 wheel double bunk forwarder, around 18000

GRAPPLE SKIDDERS

07' JD 748G III ($49.5K)

Have videos available

72ND ANNUAL GREAT LAKES LOGGING & HEAVY EQUIPMENT EXPO Thurs, 7 Sept - Sat, 9 Sept Escanaba, Michigan

MID-ATLANTIC

-Meter reads 1hr, because it was just replaced, but it

& BIOMASS Fri, 15 Sept - Sat, 16 Sept

showed those hours before install -Tires size: 30.5’s -Tires tread: 80% -Gears shift smoothly -Dual arch -A/C and heat both work -Winch and grapple work -Engine & transmission rebuilt by John Deere 1yr prior to owner buying it about a year ago. -Reason for selling: he mostly cuts small tracts and mostly by himself. Too big for what he does -Everything works as it should.

BANDMILLS & HEADSAWS

Danckaert Band Resaw Roughly 10 hours on this machine since it has been rebuilt, it has a 24foot in feed deck 20 foot out feed deck with 44 inch wheels, and all the bells and whistles, its a production machine, with air strain conveyers that go up and down, with airbags, it includes two sets of Mcdonough

Item ID 100127. Joe x709

83' TJ 380A ($29.5K)

New winch drive shaft -New injection pump -Bushings replaced in spring 2020 -Tiny slop in the center section -New glass in the cab -Motor is from a 93’ dodge pick-up truck with low hours installed in summer 2019 -Owner ran it two seasons, then bought a bigger skidder in 2020 -New cylinders for the grapple, -4 speed clark powershift -Tires size: 24.5 x 32, -Owner will put a brand new tire on before sale -4 chains come with sale -2yrs owner -Owner went pretty much thru everything, machine is at work everyday right now. It's ready to go make $$$$ elsewhere.

Item ID 100126. Joe x709

13' CAT 545C ($64.5K)

Tires size: 35.5’s -A/C works -It’s got new injectors, too -Center Section is good -Blade is fine -Enclosed cab -Tight machine. Everything works as it should -Reason for selling: owner is a Tigercat fellow. Wanted to try CAT and

compare. He’s sticking with Tigercat, this can go.

Item ID 100123. Joe x709

TJ 450 (FOR PARTS OR FIXING)

Engine is in good working conditions. Machine cranks up but doesn't move, it just idles. Grapple works, no winch, good tires tread still. Can be a fixer upper or used for parts

Item ID 100112. Joe x709

2009 CAT 545C ($48K)

Meter reads: 12000 +/- -Center section has no slack -Brand new transmission in 2019. HOLT CAT in TX installed it -All bearings and selas replaced -All braces and supports replaced -Machine is good to go. -Everything works as it should -Owner is not into logging anymore

Item ID 100109. Joe x709

13428 Victory Ln. // PO Box 124 Adams Center, NY 13606

98' TIMBERJACK 460C

1998 Timberjack 460C grapple and winch skidder, has under 500 hours on a new crate engine, machine starts, runs, and shifts great. Has new lexan

glass, all cylinders have been recently repacked, tight center section, the oil cooler leaks a bit, and could be replaced but that is the only repair that it could use. Other than that it is woods ready. Call for more information.

with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703

Brewco Saws - Two Brewco Saws in excellent condition. Runs great. Item ID 13644. Sam x702

2010 Shop Built Wood Processor

-It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot

‘16 Halverson H140 Skidsteer (DEMO)

Item ID 100106. Austin x703

Item ID: JW-909632

Contact: J Williams Ph: (888) 401-6367 x701

14' JOHN DEERE 748H

2014 model John Deere 748H with 13000 original hours, has the sweda axles, with 44'' tires.

One owner/operator skidder, that has been well maintained. Call for more info.

Item ID 100099. Austin x703

15' CAT 545D

‘13 KMC 2500 Track Skidder

Item ID: 14078

Contact: Austin Ph: (888) 401-6367 x703

2015 Cat 545D grapple skidder with winch, and 44'' flotation tires, skidder has 4000 original hours, and all of the components work like they should, good center pins, no bad leaks, heat/ ac works. Working daily. Call for more info.

Item ID 100098. Austin x703

CTR 950 CTR 950 Grapple and winch

off onto a conveyor. This is a very well built processor. Item ID 13820.

‘93 Barko 180B

skidder has 5.9 cummins engine, john deere winch, two sets of diamond double chains. Rebuilt the grapple controls recently as well as new fuel pump. Skidder has been well kept and is ready for work.

Item ID 100097. Austin x703

Item ID: 14077

Contact: Austin Ph: (888) 401-6367 x703

06' JD 648G III ($37.5K)

Single arch -Winch doesn't have cable from lever to the winch -A/C works, heat good -Center pins have a little slack, not horrible -Tires size: 30.5 -Direct Drive machine

-Owner is downgrading, down to 1 crew -3yrs owner -Good skidder, will go right to work

Item ID 100077. Joe x709

‘95 John Deere C6 Tree Farmer

Item ID: 13920

10' JOHN DEERE 648H

2010 model John Deere 648H

Contact: Austin Ph: (888) 401-6367 x703

capacity!. Item ID 13421. Sam x702

BARKO

-Torque Converter machine -Has 7500 frame hours -New 210 HP engine installed at 5000 hours -Good Rubber -New windows -Cold AC -Owner operator machine -Working daily Call for more info.

1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous

Item ID 100064. Austin x703

on injection pump. always started good. in good working order. 22in

1999 Barko 160D - new engine with meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks.

a brand new Duetz engine. Lever control, 33” bar, pump and tranny

LINK-BELT

JOHN DEERE 648H

2008 Model John Deere 648H it has the heavy axles, and around 100 hours on a complete powertrain warranty, the motor, transmission, fuse panel, center section, glass, and all of the pins and bushings have either been replaced, or rebuilt. It is as close to a new skidder on the used market as you can get. Call for more info.

winch that has been all rebuilt. Working daily.

Item ID 100048. Austin x703

info@empirehyd.com

TIGERCAT 610C

Tigercat 610C nice tight machine with 7800 hours currently, has good center pins, and doesn't burn any oil. Working daily. Call for more info.

Item ID 100046. Austin x703

CLARK 666C

Item ID 100051. Austin x703

TIMBERJACK 460

Timberjack 460 has 5,9 cummins, 3 speed trans, esco grapple, strong winch, dry skidder doesn't burn oil. Working daily, video available if interested.

Item ID 100049. Austin x703

TIMBERJACK 240A GRAPPLE

1992 model Timberjack 240A all original factory made grapple skidder, hour meter shows 2800 hours, but has rolled over, so around 12800 original frame hours. runs great, tight pins and bushings, no leaks, strong gearmatic

13428 Victory Ln. // PO Box 124 Adams Center, NY 13606

CAT 515

2000 model Cat 515 skidder with winch It will include a professionally made arch, so that one could use it as a cable machine if wanted. It currently sits right at 5900 original frame hours. Tire size 28L and the front two tires are going to be replaced with brand new ones before purchase. Inside the cab has good heat/ac and all good glass. This skidder has been meticulously maintained, and every component works like it should. Call for more info.

Item ID 100029. Austin x703

with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703

Brewco Saws - Two Brewco Saws in excellent condition. Runs great. Item ID 13644. Sam x702

2010 Shop Built Wood Processor

-It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot

‘16 Halverson H140 Skidsteer (DEMO)

Item ID: JW-909632

Contact: J Williams Ph: (888) 401-6367 x701

Clark 666C grapple and winch skidder, just had the 453 Detroit engine overhauled a few hundred hours ago, center section is tight, has new center pins in the front end, along with new pivot pins, also replaced all the cylinders in the continuous grapple. has new 23.1 firestone tires on the back. Everything else works as it should, no bad leaks, it is woods ready.

Item ID 99903. Austin x703

TIMBERJACK 450C

‘93 Barko 180B

Item ID: 14077

Contact: Austin Ph: (888) 401-6367 x703

‘13 KMC 2500 Track Skidder

Item ID: 14078

Contact: Austin Ph: (888) 401-6367 x703

95 Timberjack 450C Grapple / Winch Skidder. Has a Prolenc snubber that was installed in October 2014. Installed a reman Cummins engine (purchased from Cummins) that now has only 1,800 hours on it. New “Heavy Duty” radiator was installed at the same time as the engine. Both rear-ends have been re-built. Transmission has been rebuilt about 4,000 hour ago. Center pins have been replaced and are tight. New suspension seat. Has no leaks /

off onto a conveyor. This is a very well built processor. Item ID 13820.

machine is dry all over. The hour meter reads 3,900 hours but previous owner said he replaced the meter at around 4,000 hours so machine is around 8000 frame hours. Has heat but no air conditioning. Winch was rebuilt by Holt Equipment. 28L X 26 tires at 90%. This machine is in excellent shape. Everything operates as it should. This was the main machine until they updated to a feller buncher and bogie skidder. Whenever it needed anything it was fixed back to new condition. This will make someone an excellent machine that will provide them years of service.

Item ID 100026. Austin x703

‘95 John Deere C6 Tree Farmer

JOHN DEERE 548G2

Item ID: 13920

Contact: Austin Ph: (888) 401-6367 x703

capacity!. Item ID 13421. Sam x702

BARKO

1997 John Deere 548G2 in mint condition, skidder has 8800 original frame hours. Pins and bushings are tight, with new center pins put in 1000 hours ago. Also has all new hydraulic lines and hoses. Skidder has always been greased and serviced regularly.

1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous

Item ID 99972. Austin x703

good. in good working order. 22in

1999 Barko 160D - new engine with meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks.

control, 33” bar, pump and tranny

Tree Started

All!

PUBLISHER

cutter is in excellent condition with new 30” pads, pump, batteries and

Waratah 624 Super - New Computer for head (Logrite). 10500 hours. New main pump and auxiliary pump. New rebuilt engine with only 300 hours. New drive motors on head for 18'/sec. Almost brand new rails on 90% UC. New front window. Super tight machine. Item ID 13595. Sam x702

Processor - This is a Chomper super 14, with a 60hp engine. In very nice shape. Only 171 hours, comes with green chain conveyer. All of the manuals for the engine, and the chopper itself come with it, as well as all of the electrical schematics. Item ID 13894. Austin x703

2007 John Deere 160 - Track excavator with a waratah processor. Owner retired. Located in Montana. Item ID 13789. Sam x702

with

disc. Undercarriage at 75%. 9400 hours. Item ID 13796. Sam x702

Manufacturing a full line of biomass fired combustion systems backed with fifty years of innovative clean-burn design. Diverse in every way with multi-fuel blending capability. Hurst stokers utilize hundreds of common and abundant solid biomass fuels. Large or small scale, project management is eased with the impressively short installation time required with prefabricated modular components.

2005 John Deere 903G Feller Buncher - GN Roy 22’’ continuous saw head. Heated & A/C cab. Standard boom. Medium pads. Operator, service, and parts books included. Item ID 13203. Sam x702

2006 JD 2554 Processor with 624 Waratah ‘Super’ Processing Head. 10500 hours. New pumps. New engine. New drive motors on head. Almost new rails. New front window. Super tight machine. Runs great. One owner!. Item ID 13550. Sam x702

2006 JD 2554 Processor with

2006 John Deere 700J Dozer - This work horse comes with a winch, and new undercarriage, it is tight and dry & running daily with 4500 hours. Item ID 13883. Austin x703

2006 John Deere 748GIII - 8700 hours, running daily. Item ID 13881. Austin x703

2006 John Deere 748GIII - This skidder comes equipped with a fire suppression system. Hour meter reads 11000 hours, but is inop now, but had a new engine at 5000 hours. Tires are 30.5 X 32 at 20% and chains on all 4 that are still in good shape. All pins are tight, very little slack in the cradle. Item ID 13930. Sam x702

2006 John Deere Firewood

2007 John Deere 2554 with 624 Waratah processor - New sprockets, rollers, and chain. 10900 hours on this machine. This machine is in excellent condition. Item ID 13760. Sam x702

2007 John Deere 648GIII - Dual arch with winch and dualing rings. Tires are 30.5’s at 50%. Straight sheet metal, glass is good, and interior is in good shape. This unit has been very well taken care of. 13,500 hours. Item ID 13710. Sam x702

2008 JD 648H w/Swing Boom Grapple - Very clean and unique machine. 6800 hours and well maintained by one owner. Young Swing Boom grapple gives you

JOHN DEERE 748G3

05’ JD 748G3 Currently working daily Skidder has 6600 original frame hours Used a backup skidder most it’s life. John Deere rebuilt front cradle roughly 10 hours ago, it also had a new wiring harness, and 2 new shift solenoids put on 2 months ago. Transmission was rebuilt 2 years ago. Ac and heat works. One back tire is 100% other back is 60% front two are 30% Skidder has always been Kept serviced and greased. Runs good, shifts good.. Operates good VIDEOS AVAILABLE.

Item ID 99967. Austin x703

JOHN DEERE 848H

2012 John Deere 848H Has 12,000 frame hours Motor and transmission were rebuilt 2 years ago. Everything works as it should, skidding wood daily.

Item ID 99963. Austin x703

TIGERCAT 610E

Tigercat 610E dual arch and grapple skidder. Everything works and is woods ready. Has new 30.5 tires on front, and

rears are at 40%, 5900 total frame hours, always greased, and well maintained.

Item ID 99935. Austin x703

JOHN DEERE 748H

2010 John Deere 748H 12000 frame hours, motor just rebuilt with low hours on it, center section is tight, has new windshield. All the other components works like they should. Call for more info.

Item ID 99920. Austin x703

JOHN DEERE 648E

John Deere 648E dual arch grapple skidder, has the 6068T motor in it, doesn't burn or use any oil, motor rebuilt a few thousand hours ago, cab has new glass. Only thing it doesn't have is a winch.

Item ID 99894. Austin x703

TIMBERJACK 450C

1996 model Timberjack 450C it has brand new 23.1 primex tires on it, with a set of ice chains. New motor installed two years ago but still has low

&

FIREWOOD PROCESSORS

2010 Shop Built Wood Processor

Lift. Uses 4-way wedge adjustable to single two way. Great Value! PA. Item ID 12062. Sam x702 Firewood Processor - This is a homemade processor with a 10’ log deck. Has a hydraulic grapple, chain and kicker that all runs off of a 4 cylinder Mercedes power unit. Has a 4’ chain saw that kicks

‘16 Halverson H140 Skidsteer (DEMO)

Item ID: JW-909632

Contact: J Williams Ph: (888) 401-6367 x701

hours on it, transmission was gone through at that time, as well as the radiator. Has enclosed cab with heat and air. This skidder has been used as a backup most of the time and is in really good shape. The only flaw is that the owner used it as a cable machine and actually sold the grapple, if someone was interested, we could help locate a grapple for you. Call for more info.

Item ID 99889. Austin x703

TIMBERJACK 240C

GRAPPLE WITH WINCH

Skidder. New center pins last year, had a new AC pump put in not too long ago... Grapple works good with no issues, cable works good too. Ready to hit the woods! call for more info.

‘93 Barko 180B

Item ID 99856. Austin x703

Item ID: 14077

Contact: Austin Ph: (888) 401-6367

2011 CAT 525C

703

‘13 KMC 2500 Track Skidder

Item ID: 14078

Contact: Austin Ph: (888) 401-6367 x703

1997 Timberjack 240C Grapple with winch, approx 9,500 hours, recently had $20,000 of work (New torque converter and anything else it needed, hoses, fitting, etc.) excellent 4BT Cummins motor, good 23.1 tires, power shift machine, meticulous maintenance, and upkeep. Super Rare Skidder! Call for more pictures!

Item ID 99861. Austin x703

‘95 John Deere C6 Tree Farmer

Item ID: 13920 Contact: Austin Ph: (888) 401-6367 x703

LUMBERMEN’S Equipment Digest PO Box 1146 Columbia, TN 38402-1146 1-800-477-7606 Fax (931) 388-3564 www.lumbermenonline.com

CAT 515 1998 CAT 515 single arch Grapple

off onto a conveyor. This is a very well built processor. Item ID 13820. Sam x702

Firewood Processor - This is a Chomper Model 16 PDA automatice firewood processor with John Deere power unit with low hours. Control panel includes tach, oil pressure, water temp and amp gauges. Cuts logs up to 16”. One owner and comes with all manuals and receipts. Purchased new for $32,500. Item ID 13865. Sam x702

LOGGING EQUIPMENT

1999 Bandit 1900 Tracked Disc Chipper - Cat Under Carriage at 50% or better. 475 hp Cummins Diesel. 7500 Hours. One owner. Well maintained. Item ID 13294. Sam x702

2004 Bandit Beast Model 46803412 Caterpillar Diesel engine with 850 HP. 5300 hrs. Mill in good condition. Just finished 10 Acre clearing job, ready to work! Remote control. Big production

capacity!. Item ID 13421. Sam x702

BARKO

2011 Cat 525C dual arch grapple skidder it has 13000 frame hours on it but has a new reman engine installed from caterpillar that is still under warranty along with a rebuilt transmission. All pins and bushings have been redone, front axle center bearing has been changed also. All pins in grapple, arch, and center section have been redone. Just calibrated it and it shifts and pulls flawlessly. Just had new injectors installed as well. Brand new 30.5 tires on the back, everything works, heat, air, radio, etc. This skidder has been totally gone through end to end and is in excellent shape. Call for more info.

Item ID 99835. Austin x703

1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous grapple, 5,000 original hours. (excellent condition.). Item ID 13238. Chris x700

1995 Barko 775 B Feller Buncher -Pumps recently redone. 400 hrs on injection pump. always started good. in good working order. 22in kohing head. head works great.

1999 Barko 160D - new engine with approximately 1500 hours. Hour meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks.

94 Barko 275 - Excellent value with low at hours at 3,500. 5.9 CUMMINS continuous grapple. Runs Great!. Item ID 13740. Sam

1990 Bell Super T - This Bell has a brand new Duetz engine. Lever control, 33” bar, pump and tranny

in

will

to closest US entry

ID

tracks like new he will add for additional $20,000. Item ID 13494. Sam x702

1999 Timbco TF-820D Forwarder11k hrs on machine, new Cummins engine at around 8k hrs and has fresh drive pump & imp. pump. 28L 26 tires some great, some decent. Machine is ready to work, but could use a little fixing here and there. the bucket is sloppy could stand to be pinned and bushed. No major issues!. Item ID 13212. Sam x702

Mag 64-knive Source Grinder

Item ID: 14007 Contact: Austin Ph: (888) 401-6367 x703

swing motor. Has new jet fit system. This machine is loaded... has pro-heat system for cold weather start. Has fire suppression system. All working! Hydraulic Oil just totally changed (100 new gallons) with new filters. Item ID 13598.

2000 Timbco 425D w/33" Bar Saw Head. 40 degree tilt on head. 540 degree rotation on upper body. One year old Cummins 6CT8.3 engine. Resealed pumps. Rebuilt valve bank. 90% undercarriage. Can accept hot saw. Fire suppression system. Auxiliary oil cooler. Good running machine. Item ID 13549. Sam x702

1998

215 HP. Machine runs great. Working in select hardwood today.

ID

1997 Timbco 820C Clam Bunk Forwarder - “4000” original hours. 20.3 x 25 rubber at 70%. Hand sanded and painted, brand new

hours.

-

at 60%. Will crank

run. Owner retired. Machine idle for past year. Item ID 13599. Sam x702

1999 Timbco 820D Clam Bunk Forwarder - 10,300 hours. New engine less than 500 hours ago. Can accept bunks, but none with machine. Owner has two sets of

2000 Timbco 415D w/2005 Fabtek 4-Roller Processor - 21,000 hours on meter. New JD 6 cylinder engine in 2011 has 7000 hours. U/C at 65%. Extensively rebuilt with new swing motor, new charge pump, new high speed saw motor, new main hydraulic pump, new oil cooler, all main cylinders repacked. Package includes extra final drive, extra computer screen, and extra

2000 Timbco 445D - Recent engine and pump last winter. New sprockets and rollers. 22” quadco hot saw. Owner retired. Located in Montana. Item ID 13790. Sam x702

2005 TimberPro 830TF Forwarder - 6580 hours. Very good condition. Tracks for all bogies. 710/45-26 tires at 70%. Includes bolsters and back rest. Comes with 36” grapple with grapple saw option.

240

Timberjack 240 grapple skidder has cummins motor, and 3 speed transmission. Recently rebuilt the winch and installed a new cable. As well has put new hydraulic lines underneath it. Has new heater inside the cab, and replaced drive shaft with a heavier one. It also has new center pins, and new master cylinder on the brakes. Its only had around 3000 hours put on it in the past 10 years.

Item ID 99828. Austin x703

TIMBERJACK 380A

Timberjack 380A has brand new 5.9 cummins motor with a 4 speed clark transmission, and a John Deere winch. Cab has Heat, windows, and full doors. Machine will continue working a job until sold. Also note that the grapple is not on in the pictures but does come with the skidder.

Item ID 79616. Austin x703

11' JOHN DEERE 648H

2011 John Deere 648H dual

arch grapple skidder, in 2015 it was refurbished through River Ridge in, Rising, AR and that was about 4000 hours ago. It has 30.5 dualing rings, heat, air, lights, radio, all work good. Everything motor, and transmission was replaced and refurbished 4000 hours ago, as well as lots of other work. Now Center sectioin has a little slack, that;s about all it could use. Woods ready machine still dragging about 5 loads a day. only Reason for selling, Owner downsized to a one man operation. Call for more pictures!

Item ID 74017. Austin x703

TIGERCAT 630E

2017 Tigercat 630E with 2400 hours on it, in excellent condition. Everything works as it should. Call for more pictures.

Item ID 84473. Austin x703

HARVESTERS & PROCESSORS

2004 TIMBCO 425EXL

2004 Timbco 425EXL with rolly processing head, the head

was rebuilt in 2016 and has the eaton measuring computer system on it. Call for more information.

Item ID 100108. Austin x703

08 ROTTNE H14

‘16 Halverson H140 Skidsteer (DEMO)

Item ID: JW-909632

Contact: J Williams Ph: (888) 401-6367 x701

2008 Rottne H14 6 wheel drive harvester, equipped with an SP6451 harvesting head, machine has 12000 frame hours, has been well kept and maintained. All major components work like they should. Call for more info.

Item ID 100107. Austin x703

KOMATSU 931.1

This machine is in really good condition with a motivated seller, financing available thru Lumbermens. Call to discuss. We have more videos upon request.

‘13 KMC 2500 Track Skidder

Item ID: 14078

Item ID 99949. Austin x703

Contact: Austin Ph: (888) 401-6367 x703

08' TIMBCO 415EX

2008’ Valmet 415Ex in excellent condition, it has just basically been completely

EQUIPMENT

BANDIT

1999 Bandit 1900 Tracked Disc Chipper - Cat Under Carriage at 50% or better. 475 hp Cummins Diesel. 7500 Hours. One owner. Well maintained. Item ID 13294. Sam x702

2004 Bandit Beast Model 46803412 Caterpillar Diesel engine with 850 HP. 5300 hrs. Mill in good condition. Just finished 10 Acre clearing job, ready to work! Remote control. Big production

gone through, has new undercarriage, new hydraulic pumps, Rolly 2 head just all rebushed. Amount of work that has recently been done to it totals close to $100,000. It has 11000 total frame hours. In the woods working now.

‘93 Barko 180B

Item ID: 14077

Item ID 99923. Austin x703

Contact: Austin Ph: (888) 401-6367 x703

VOLVO DELIMBER

2011 Volvo delimber 16,644hrs well maintained great shape. Engine has 9,500hrs on it, pins and bushings in boom recently replaced everything is tight and dry ready to work.

Item ID 99919. Austin x703

John Deere C6 Tree Farmer

TIMBCO 425 EXL

Item ID: 13920

Contact: Austin Ph: (888) 401-6367 x703

capacity!. Item ID 13421. Sam x702

BARKO

2004 Timbco 425 EXL has 7400 hours currently with a new undercarriage installed 500 hours ago. Hydraulic pumps and drive motors have been replaced as well less than 1000 hours ago. Has new saw motor also. Is ready to work all it needs is a job.

Item ID 99855. Austin x703

1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous grapple, 5,000 original hours. (excellent condition.). Item ID

1995 Barko 775 B Feller Buncher -Pumps recently redone. 400 hrs on injection pump. always started good. in good working order. 22in kohing head. head works great. Item ID 13185. Sam x702

1999 Barko 160D - new engine with approximately 1500 hours. Hour meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks. Item ID 13694. Sam x702

94 Barko 275 - Excellent value with low at hours at 3,500. 5.9 CUMMINS continuous grapple. Runs Great!. Item ID 13740. Sam x702

Bell Super T - This Bell has a brand new Duetz engine. Lever control, 33” bar, pump and tranny

Mortgage Rates Surge, Lumber Prices Fall

Lumber prices declined after the

info@empirehyd.com

hiked interest rates by 75 basis points. The aggressive interest rate hike from the Fed helped solidify the recent surge in

rates to above 6 percent.

‘93 Barko 180B

“The lumber market continues to be in a state of overall malaise as buyers anticipate lower overall demand going forward,” Sherwood Lumber told Insider.

‘16 Halverson H140 Skidsteer (DEMO)

Item ID: 14077

Contact: Austin Ph: (888) 401-6367 x703

Item ID: JW-909632

The aggressive interest rate hikes from the Fed have helped solidify the ongoing surge in mortgage rates, which jumped above 6 percent for the first time since 2008 earlier this month and have doubled over the past year. The average 30-year fixed mortgage rate surged another 27 basis points to 6.29 percent, according to data from Freddie Mac.

Contact: J Williams Ph: (888) 401-6367 x701

The surge in mortgage rates has taken a significant bite out of home sales, which has in-turn led to price cuts and has dented homebuilder sentiment.

“The lumber market continues to be in a state of overall malaise as buyers anticipate lower overall demand going forward. Many yards are trying to pare their inventories to minimum levels and have really no fear of price upside,” Sherwood Lumber’s director of risk management Steve Loebner told Insider.

“This has taken all of the urgency of the past two years out of the market,” said Loebner.

“We have had a few supply and transportation scares which caused short term rallies However, these have all been quickly shrugged off. Home prices are resetting to reflect the higher mortgage rates, and this is a process which can take some time.”

‘95 John Deere C6 Tree Farmer

The housing market has not completely fallen apart, and after a more than 70 percent decline from its record high, lumber prices can still catch a bid going forward.

‘13 KMC 2500 Track Skidder

“There is still a solid backlog of demand on existing single and multi-family [housing] projects,” noted Loebner.

Item ID: 13920 Contact: Austin Ph: (888) 401-6367 x703

“Multi-family demand in particular has been very robust, and many traders report near record backlogs of projects on the books which will be starting over the next few quarters.

Item ID: 14078

We have also started to see some modest [lumber] production curtailments, which over time will become more prevalent if pricing remains depressed.”

13428 Victory Ln. // PO Box 124 Adams Center, NY 13606

capacity!. Item ID 13421. Sam x702

BARKO

Steady demand for the essential building commodity, combined with declining supply due to potential production curtailments, could ultimately spell upside for lumber in the future, at least as long as demand holds up.

off onto a conveyor. This is a very well built processor. Item ID 13820. Sam x702

TimberPro Expanding Factory

‘05 Gehl CTL 70

“We are in for a slower grind and a more challenging market environment. However with many of the benchmark commodity lumber items already down approximately 70 percent from their levels earlier this year, the pervasive bearish sentiment, and the likelihood of less supply, traders would be well advised to consider the risk/reward of being overly negative at this point,” Loebner concluded.

Item ID: JW-986495

1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous grapple, 5,000 original hours. (excellent condition.). Item ID 13238. Chris x700

TimberPro, a manufacturer of forestry equipment, will significantly expand its factory in Shawano, Wisconsin. The $8 million construction project will add more than 48,000 square feet to the company’s existing facility.

‘83 John Deere 4850

Contact: J Williams Ph: (888) 401-6367 x701

“Forestry is very important to our state’s economy, and expanding our operation will enable us to provide more good, familysupporting jobs in northern Wisconsin,” said Lee Crawford, CEO of TimberPro. “This expansion will also allow us to enhance our research and development capabilities and significantly increase our production of existing and new products.”

Item ID: 14073

Contact: Austin Ph: (888) 401-6367 x703

chain conveyer, 8 way splitter, on 20,000lb goose neck trailer. Item ID 13916. Austin x703

1995 Barko 775 B Feller Buncher -Pumps recently redone. 400 hrs on injection pump. always started good. in good working order. 22in kohing head. head works great. Item ID 13185. Sam x702

The expansion will enable TimberPro to double its production capacity to help meet market demand for the equipment and attachments manufactured at the facility. In conjunction with the expansion, the company anticipates adding new positions for assemblers, welders, machinists and office staff. The expansion project should be completed and ready for occupancy in the summer of 2023.

Brewco Saws - Two Brewco Saws in excellent condition. Runs great. Item ID 13644. Sam x702

FIREWOOD PROCESSORS

2010 Shop Built Wood Processor -It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot

Best Value Portable Log Splitter -Small manufacturer in PA has made the best valued log splitter. Handles logs up to 32”. Uses 13HP Honda motor. Manual start but electronic option is available. Has Log Lift. Uses 4-way wedge adjustable to single two way. Great Value! PA. Item ID 12062. Sam x702

Firewood Processor - This is a Chomper Model 16 PDA automatice firewood processor with John Deere power unit with low hours. Control panel includes tach, oil pressure, water temp and amp gauges. Cuts logs up to 16”. One owner and comes with all manuals and receipts. Purchased new for $32,500. Item ID 13865. Sam x702

Founded by the Crawford family in 2002, TimberPro is a Wisconsin-based manufacturer of purpose-built forest machines and attachments, offering track feller bunchers and harvesters, forwarders, wheel harvesters, and felling heads. TimberPro was acquired by Komatsu in 2019.

LOGGING EQUIPMENT

BANDIT

Contact: Austin Ph: (888) 401-6367 x703 with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703

1999 Bandit 1900 Tracked Disc Chipper - Cat Under Carriage at 50% or better. 475 hp Cummins Diesel. 7500 Hours. One owner. Well maintained. Item ID 13294. Sam x702

Firewood Processor - This is a homemade processor with a 10’ log deck. Has a hydraulic grapple, chain and kicker that all runs off of a 4 cylinder Mercedes power unit. Has a 4’ chain saw that kicks

2004 Bandit Beast Model 46803412 Caterpillar Diesel engine with 850 HP. 5300 hrs. Mill in good condition. Just finished 10 Acre clearing job, ready to work! Remote control. Big production

1999 Barko 160D - new engine with approximately 1500 hours. Hour meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks. Item ID 13694. Sam x702

94 Barko 275 - Excellent value with low at hours at 3,500. 5.9 CUMMINS continuous grapple. Runs Great!. Item ID 13740. Sam x702

1990 Bell Super T - This Bell has a brand new Duetz engine. Lever control, 33” bar, pump and tranny

CALENDAR**

NY STATE WOODSMEN'S FIELD D AYS

Wood-Mizer Introduces Planer-Moulder Rip Saw

Fri, 18 August - S un, 20 August Boonville, New York www.starwebhosting.net/woodsmen/

FOR

See pictures, prices, and Location of all equipment at www.LumberMB\ISmagazine.com

Wood-Mizer has introduced the MP220 Planer-Moulder Rip Saw, a versatile three-in-one woodworking machine able to produce finished wood trim, flooring, dimensional lumber and more from rough sawn material.

SOUTHWEST FOREST PRODUCTS EXPO

BANDMILLS & HEADSAWS

The MP220 Planer-Moulder Rip Saw can plane and rip in one pass or mould and rip in one pass, saving time and increasing production and profitability.

The Tree that Started it All!

Fri, 25 August - Sat, 26 August Hot Springs, Arkansas www.arkloggers.com

“In addition to three-in-one versatility for planing, moulding, and rip sawing, woodworkers will appreciate the simple and efficient operation to save time, the precision to produce high-quality and value-added finished products, and the compact design to free up valuable workshop space,” said Chad Sanders, Wood-Mizer woodworking product specialist.

Since 1986, Lumbermens has published a monthly circular reaching sawmills, loggers, pallet makers, recyclers and industrial woodworking plants worldwide.

72ND ANNUAL GREAT LAKES LOGGING & HEAVY EQUIPMENT EXPO

Thurs, 7 Sept - Sat, 9 Sept Escanaba, Michigan

The MP220 features one horizontal cutter for planing or moulding and one circular saw blade for rip sawing or resawing material. The horizontal cutter can be fitted with planing knives or moulding profile knives to produce finished boards and mouldings with a capacity of \!-inch to 15-¾ inches wide by ]!-inch to 9-½ inches high. Edging or rip sawing of material is accomplished by the adjustable 9-inch diameter circular saw blade with a rip sawing capacity of 4-1/2 inches to 11 inches wide by 3-1/8 inches high.

MID-ATLANTIC LOGGING & BIOMASS

PUBLISHER

Woods Publishing

ADVERTISING SALES

MID-ATLANTIC LOGGING

EXPO

Fri, 15 Sept - Sat, 16 Sept Selma, North Carolina www.midatlantic-logging-biomassexpo.com/

For accurate, consistent results, two steel and one polyurethane feed rollers efficiently move material on the heavy-duty cast-iron table through the horizontal cutter and rip saw blade at a variable speed, from 6 to 36 feet per minute. The compact size and optional casters save floor space and provide flexibility to move the MP220 around the workshop.

Morris Woods (888) 401-6367 ext. 704 morris@lumbermens.co

The MP220 can use either single phase or 3-phase electric power.

KENTUCKY WOOD EXPO

The MP220 joins the established Wood-Mizer range of woodworking equipment that includes jointer/planers, two-sided planer/ moulders, four-sided planer/moulders, slab flattening machines, dust collection systems, planer blades, moulder knives, and more.

MARKETING DIRECTOR

John Williams (888) 401-6367 ext. 701 j@lumbermens.co

Fri, 15 Sept - Sat, 16 Sept Lexington, Kentucky http://www.kfia.org/ KentuckyWoodExpo.aspx

Danckaert Band Resaw Roughly 10 hours on this machine since it has been rebuilt, it has a 24foot in feed deck 20 foot out feed deck with 44 inch wheels, and all the bells and whistles, its a production machine, with air strain conveyers that go up and down, with airbags, it includes two sets of Mcdonough pressure guides. To p Casting wheel is supported on both sides. This is an extremely accurate machine in ve1y good condition, Cuts 130 feet a minute also has CLT presses. Item ID 13876. Austin x703

The MP220 Planer-Moulder Rip Saw is available to order worldwide. Planer blades, circular saw blades, moulder knives, and dust collection systems are also available from Wood-Mizer.

For more information, visit woodmizer.com or contact your local Wood-Mizer representative.

DESIGN DIRECTOR

Donna Heninger

THE PAUL BUNYAN SHOW

Maine Industry to Get $14 Million in Grants

EQUIPMENT REPS

Sam Wall (888) 401-6367 ext. 702 sam@lumbermens.co

Fri, 6 Oct - Sun, 8 Oct Cambridge, Ohio www.ohioforest.org

Maine Gov. Janet Mills announced $14 million in grant funding is now available for Maine forestry companies from the second round of the Forest Recovery Initiative of her Maine Jobs & Recovery Plan.

S & W 125 Band Mill with Caterpillar generator Low hours on the mill, electronic computer Set works,1 1/2" or 2" band, 22ft. track Cat 3406 140KW Genset, 12,400 hours ready to run. Item ID 13434. Sam x702

CARRIAGES & DRIVES

Austin Woods (888) 401-6367 ext. 703 austin@lumbermens.co

Mills announced the $20 million Forest Recovery Initiative grant program through her Maine Jobs & Recovery Plan in November 2021. The first phase of the program provided financial relief to 219 forest products industry businesses that experienced negative impacts from the pandemic to help them sustain the viability of their business. Of the 219 companies awarded grants, 83 percent have ten employees or fewer.

MAILING ADDRESS P.O. Box 1916 Columbia, TN 38402-1916 (888) 401-6367

The second and final phase of the program, administered by the Maine Technology Institute (MTI), will provide grants ranging from $250,000 to $2,000,000 to forestry companies to support forward-looking projects that address new market demands, provide new sustainable products, or otherwise advance the long-term stability of the forestry industry.

AD SUBMISSIONS

May be sent tomorris@lumbermens.co

Funds may also support infrastructure upgrades that strengthen the supply chain and help businesses pivot to new products and markets.

POSTMASTER

2010 Cardinal HD Carriage Carriages (Sawmill) Cardinal Carriage line it includes carriage with onboard log turners, carriage drive, hyd pac for carriage, sawyers cab, computer controls, cabinet with electronic drives for carriage knees, husk including 48" bottom saw and 36" top saw

These new grants are dedicated to supporting innovative businesses in our forest products sector that are already making Maine’s heritage industry more competitive on the world stage,” said Mills. “My Administration will continue to support our forest products industry and the people it employs across our state.”

Send address changes to: Lumberman's Exchange P.O. Box 1916 Columbia, TN 38402

The published Publishing, Columbia, reserved. submissions discretion be and been content submitted and Exchange, associates, errors in out

BANDSAW BLADES

All Sizes Available!

SAFETY ALERT

Dusty Haul Road Leads to Accident

‘16 Halverson H140

BACKGROUND

Skidsteer (DEMO)

‘93 Barko 180B

Item ID: 14077

Contact: Austin Ph: (888) 401-6367 x703

Item ID: JW-909632

Contact: J Williams Ph: (888) 401-6367 x701

On a late spring day in the Pacific Northwest, two pickup trucks loaded with ATVs were traveling down a major haul road at the end of the day, one behind the other. Dry weather had resulted in dusty road surface conditions.

PERSONAL CHARACTERISTICS

The drivers’ experience and training were unknown.

UNSAFE ACTS AND CONDITIONS

‘95 John Deere C6

Tree Farmer

Item ID: 13920

‘13 KMC 2500 Track Skidder

Item ID: 14078

Contact: Austin Ph: (888) 401-6367 x703

The trucks were traveling together, although they were a considerable distance apart. The lead truck stirred up considerable dust, making it difficult for trailing vehicles to see. The dust and a crest of a hill in the road severely limited visibility. Spring road maintenance work had created a large depression in the road surface.

ACCIDENT

capacity!. Item ID 13421. Sam x702

Brewco Saws - Two Brewco Saws in excellent condition. Runs great. Item ID 13644. Sam x702

2010 Shop Built Wood Processor -It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot

off onto a conveyor. This is a very well built processor. Item ID 13820. Sam x702

BARKO

The first truck came over the crest of a hill, and the driver saw the large depression in the road and slammed on the brakes. The truck still hit the depression hard. The driver slowed down to assess if the straps had loosened on the ATV from the impact, but there was no safe place to pull over. The second truck was a few minutes behind. As it came over the crest of the hill, the driver could see the brake lights of the stopped truck in very thick dust. He tried to stop but rear-ended the first truck, causing significant damage.

INJURY

1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous grapple, 5,000 original hours. (excellent condition.). Item ID 13238. Chris x700

1995 Barko 775 B Feller Buncher -Pumps recently redone. 400 hrs on injection pump. always started good. in good working order. 22in kohing head. head works great. Item ID 13185. Sam x702

The driver of the second truck cut his hand on glass when the windshield blew out. Fortunately, his injuries were not more serious. No one else was hurt.

RECOMMENDATIONS FOR CORRECTION

Firewood Processor - This is a Chomper Model 16 PDA automatice firewood processor with John Deere power unit with low hours. Control panel includes tach, oil pressure, water temp and amp gauges. Cuts logs up to 16”. One owner and comes with all manuals and receipts. Purchased new for $32,500. Item ID 13865. Sam x702

• Leave a safe margin of distance between vehicles. Factors to consider:

LOGGING EQUIPMENT BANDIT

Contact: Austin Ph: (888) 401-6367 x703 with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703

–dust and the crest of

1999 Bandit 1900 Tracked Disc Chipper - Cat Under Carriage at 50% or better. 475 hp Cummins Diesel. 7500 Hours. One owner. Well maintained. Item ID 13294. Sam x702

hill

1999 Barko 160D - new engine with approximately 1500 hours. Hour meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks. Item ID 13694. Sam x702

narrow road –traveling downhill –rough road conditions –weight of ATV affects braking distance

on

• Slow down to reduce collision potential and give

enough time to react.

94 Barko 275 - Excellent value with low at hours at 3,500. 5.9 CUMMINS continuous grapple. Runs Great!. Item ID 13740. Sam x702

• If dust is extremely bad, immediately pull over and stop until visibility has cleared. Look for a turnout or wide spot.

BELL

• Drive with headlights and taillights on.

2004 Bandit Beast Model 46803412 Caterpillar Diesel engine with 850 HP. 5300 hrs. Mill in good condition. Just finished 10 Acre clearing job, ready to work! Remote control. Big production

1990 Bell Super T - This Bell has a brand new Duetz engine. Lever control, 33” bar, pump and tranny

• Let others know by calling on the radio if you encounter a hazard or plan to slow down or pull over, especially in dusty conditions.

EQUIPMENT

BANDIT

Tree that Started

Morbark PS8 Post Peeler

Contact:

Fence

Contact:

Woodmizer Smart Log Processing

Pak

Cornell Sizer

Contact:

Baker Notcher

Contact:

Morbark Stac Trac

&

Precision Husky Chipper

Tajfun 480 Plus Joy

Contact: AUSTIN

Email: Austin@lumbermensco.com

Phone: 888-401-6367

931-797-8029

Bandit Grinder - Chipper

Contact: AUSTIN

Email: Austin@lumbermensco.com Phone: 888-401-6367

2008

Contact:

289C

Morbark 30/60 Chipper

Tajfun 400 Joy

Item ID:

Contact: AUSTIN

Email: Austin@lumbermensco.com

Phone: 888-401-6367

931-797-8029

2008 Cat Skid Steer 289C

Contact:

chain and kicker that all runs off of a 4 cylinder Mercedes power unit. Has a 4’ chain saw that kicks

off onto a conveyor. This is a very well built processor. Item ID 13820.

H240 John Deere Tractor

Contact: AUSTIN

Email: Austin@lumbermensco.com

Phone: 888-401-6367

931-797-8029

Firewood Processor - This is a Chomper Model 16 PDA automatice firewood processor with John Deere power unit with low hours. Control panel includes tach, oil pressure, water temp and amp

Cuts logs up to 16”. One owner and

with all

for $32,500. Item ID

x702

LOGGING EQUIPMENT

BANDIT

Ford Bucket / Boom Truck

Contact: AUSTIN

grapple, 5,000 original hours. (excellent condition.). Item ID 13238.

Email: Austin@lumbermensco.com

Phone: 888-401-6367

931-797-8029

John Deere 85D

CAT 318CL

Contact:

1999 Bandit 1900 Tracked Disc Chipper - Cat Under Carriage at 50% or better. 475 hp Cummins Diesel. 7500 Hours. One owner. Well maintained. Item ID 13294. Sam x702 2004 Bandit Beast Model 46803412 Caterpillar Diesel engine with 850 HP. 5300 hrs. Mill in good condition. Just finished 10 Acre clearing job, ready to work! Remote control. Big production

John Deere 700J LGP

Contact:

Phone:

& B Mfg.

Mfg.

‘93 Barko 180B

with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703

Brewco Saws - Two Brewco Saws in excellent condition. Runs great. Item ID 13644. Sam x702

2010 Shop Built Wood Processor

-It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot

Value! PA.

H. Payne

Inc.

‘16 Halverson H140 Skidsteer (DEMO)

Equipment Inc.

800-752-0627

Item ID: 14077

888-775-4883

Contact: Austin Ph: (888) 401-6367 x703

704-651-6061

Force

Item ID: JW-909632

Contact: J Williams Ph: (888) 401-6367 x701

800-803-3365

715-678-0037 Buck Equipment (AIM)

Cord King

CW Mill

10, 39

423-698-0284

888-219-WOOD Corley Mfg

800-743-3491

800-355-1250 GoFast Manufacturing 17 800-854-7439 Great Lakes Mfg.

F&R Mfg.

877-248-5677 Holtec

Hurdle Machine Works Inc

‘95 John Deere C6 Tree Farmer

holtecusa.com

901-877-6251

Hurst Boiler.

Item ID: 13920

425-486-1246

877-774-8778 James G. Murphy Co.

Kilgore Saw Company

Contact: Austin Ph: (888) 401-6367 x703

888-857-5153

‘13 KMC 2500 Track Skidder

Lignomat

Item ID: 14078

800-227-2105 Lumbermens Equipment Sale 25 888-401-MENS Lumbermens Wanted

Menominee Saw......................

Contact: Austin Ph: (888) 401-6367 x703

931-797-8029

capacity!. Item ID 13421. Sam x702

BARKO

800-582-0470

Metal Detectors, Inc.

541-345-7454 Midwest Sharpening

231-924-5953

Multitek North America LLC

off onto a conveyor. This is a very well built processor. Item ID 13820. Sam x702

Piper’s Saw Shop.....................

800-211-9468

800-243-5438 Pantron Automation, Inc.

800-845-6075

Rawlings Wood Hogs

1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous grapple, 5,000 original hours. (excellent condition.). Item ID 13238. Chris x700

866-762-9327 Row Electric..............................

800-248-4479 Ryan's Equipment....................

Sawmill Service

Firewood Processor - This is a Chomper Model 16 PDA automatice firewood processor with John Deere power unit with low hours. Control panel includes tach, oil pressure, water temp and amp gauges. Cuts logs up to 16”. One owner and comes with all manuals and receipts. Purchased new for $32,500. Item ID 13865. Sam x702

LOGGING EQUIPMENT

BANDIT

1999 Bandit 1900 Tracked Disc Chipper - Cat Under Carriage at 50% or better. 475 hp Cummins Diesel. 7500 Hours. One owner. Well maintained. Item ID 13294. Sam x702

2004 Bandit Beast Model 46803412 Caterpillar Diesel engine with 850 HP. 5300 hrs. Mill in good condition. Just finished 10 Acre clearing job, ready to work! Remote control. Big production

1995 Barko 775 B Feller Buncher -Pumps recently redone. 400 hrs on injection pump. always started good. in good working order. 22in kohing head. head works great. Item ID 13185. Sam x702

989-427-2829 Smith Machine Worx..............

205-620-4455

1999 Barko 160D - new engine with approximately 1500 hours. Hour meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks. Item ID 13694. Sam x702

94 Barko 275 - Excellent value with low at hours at 3,500. 5.9 CUMMINS continuous grapple. Runs Great!. Item ID 13740. Sam x702

BELL

1990 Bell Super T - This Bell has a brand new Duetz engine. Lever control, 33” bar, pump and tranny