Material Safety Data Sheet May be used to comply with OSHA's Hazard Communication Standard, 29 CFR 1910. 1200. Standard must consulted for specific requirements. IDENTIFY (As used on Label and List): SLV-105, Extruded PVC Tubing Section I Manufacturer's Name:
Phone Number for Information:
Insulation Sources Inc. DBA: ICO RALLY
650-856-9900
Address:
Date Prepared
2575 E Bayshore Rd Palo Alto, CA 94303
07/19/02
Section II - - - Hazardous Ingredients/Identify Information Hazardous Components (Specific Chemical Identity): OSHA PEL ACGIH TVL NOT APPLICABLE
NONE
Other Limits %(optional)
NONE
NONE
NONE
(REFER TO ATTACHED NOTES 1 & 3) ALL OF THE INGREDIENTS CONTAINED IN THIS COMPOUND ARE LISTED N I THE CANADIAN DSL, AND THUS ARE EXEMPT FROM REPORTING.
Section III - - - Physical / Chemical Characteristics Boiling Point Greater than 500∞F Vapor Density (mm HG)
N/A
Specific Gravity (Water = 1)
N/A
N/A
N/A
Vapor Density (Air = 1)
N/A
Melting Point Greater than 350∞F Evaporation Rate (Butyl Acetate = 1)
Solubility in water
N/A
N/A
Appearance and Odor PELLETS, VERY SLIGHT ODOR Section IV - - - Fire and Explosion Hazard Data Flash Point (Method Used) Temperature Greater Than 500∞F (Open Cup)
N/A
Flammable Limits N/A
LEL N/A
UEL N/A
Extinguishing Media CO2, Water, Dry Chemical
Special Fire Fighting Procedures NONE
Unusual Fire and Explosion Hazards NONE Page 1 of 4
Section V - - - Reactivity Data Stability Unstable
Conditions to Avoid
NO
NONE Stable YES Incompatabilities (Materials to Avoid) NONE Hazardous Decomposition Products HYDROGEN CHLORIDE (HCL), CARBON DIOXIDE, CARBON MONOXIDE (SEE ATTACHED NOTE 5) Hazardous Polymerization
May Occur
NO
Will Not Occur
YES
Conditions to Avoid NONE
Section VI - - - Health Hazard Data Route(s) of Entry: Inhalation? (REFER TO ATTACHED NOTES 2, 3, & 5)
YES
Skin?
YES
Ingestion?
YES
Health Hazards (Acute and Chronic) (REFER TO ATTACHED NOTES 3 & 5) Carcinogenicity:
NTP?
NONE
ARC?
NONE
OSHA Reg?
NONE
Signs and Symptoms of Exposure (REFER TO ATTACHED NOTES 3 & 5) Medical Conditions Generally Aggravated by Exposure (REFER TO ATTACHED NOTE 3) Emergency and First Aid Procedures (REFER TO ATTACHED NOTE 4) Section VII - - - Precautions for Safe Handling and Use Steps to Be Taken in Case Material is Released or Spilled SWEEP UP
Waste Disposal Method RECYCLE IN PLANT OR SELL FOR RECYCLING. IF DISPOSING ASWASTE, DISPOSE OF IN ACCORDANCE WITH FEDERAL, STATE AND LOCAL LAWS. Precautions to be Taken in Handling and Storing NONE
Other Precautions NONE Section VIII - - - Control Measures Respiratory Protection (Specialty Type) NIOSH APPROVED ORGANIC MIST MASK IF TEMPERATURES EXCEED 500∞F Ventilation
Special
NONE
Other
NONE
Local Exhaust at Processing Point Mechanical (General): Depends on Plant Conditions
Protective Gloves: IF HANDLING HOT PLASTIC ONLY Other Protective Clothing or Equipment: NONE
Eye Protection: RECOMMENDED FOR ALL INDUSTRIAL AREAS
Work / Hygienic Practices: NONE Page 2 of 3
ADDITIONAL NOTES 1.
Although this compound may have individual components which are defined as hazardous by the OSHA Standard CFR Title 29. 1910. 1200, their concentrations fall below the 1% cut-off level, are not carcinogenic, or are bound into the non-leachable plastic matrix.
2.
EXPOSURE TO PELLITIZED PRODUCT AT AMBIENT TEMPERATURES AND CONDITIONS Lynn Plastics has submitted various compounds for dermatological and single dose oral toxicity testing to an accredited independent laboratory with results as follows: (a) The test materials are non-irritating when tested in laboratory animals according to the Toxic Substances Control Act (TSCA) test guidelines, and, (b) The test materials, based on standards set by TSCA guidelines, 40 CFR 798.1175 are define d as non-toxic.
3. EXPOSURE TO PROCESSING VAPORS AT ELEVATED TEMPERATURES Processing vapors may produces acute health effects in some individuals. These effects relate primarily to eye, nose, and throat irritation. Individuals with bronchial asthmaand other types of chronic obstructive respiratory disease may develop bronchospasm if exposure is prolonged. 4. EMERGENCY AND FIRST AID PROCEDURES If irritation persists, remove the affected individual from the area. Call a physician. Provide protec tion before re-entry. If over-exposure occurs, leave the area. 5.
HAZARDOUS DECOMPOSITION PRODUCTS Under abnormal processing conditions (including equipment malfunctions of plug-up) decomposition of PVC compound may occur in an extruder, injection molding machine, or other processing equipment, resulting in a characteristic whitish smoke which will contain hydrogen chloride and vapors from metallic stabilizers and other ingredients. Inhalation will result in irritation of the respiratory tract, eyes,and skin resulting in coughing, pain, and inflammation. Employees involved in removing decomposing materials should be provided with suitable air supplied respirators. Decomposing compound should be removed to a well ventilated area, preferably outdoors and thoroughly soaked with water. Stand safely back while dosing since water contacting the hot decomposing compound may result in an explosion like burst of steam. The process of regrinding PVC scrap for extrusion of waste disposal may result in some dusting conditions. Local ventilation as well as NIOSH approved respiratory masks is advisable to prevent inhalation of dust.
HMIS RATING HEALTH
0
FLAMMABILITY
0
REACTIVITY
0
PERSONAL PROTECTION: REFER TO MSDS
Page 3 of 4
ICO RALLY 2575 E Bayshore Road Palo Alto, CA 94303 DATE:
07/19/02 The purpose of this attachment is to inform you that the product we sell to you,SLV-105, Clear, extruded PVC tubing, contains the following substances which appear in Section 313 of the Emergency Planning and Community Right To Know Act of 1986.
CAS #
NO MORE THAN (% BY WEIGHT)
BARRIUM COMPOUND(S)
N/A
3.00
ZINC COMPOUND(S)
N/A
3.00
SUBSTANCE
This law requires certain manufacturers to report on annual emissions of specific toxic chemicals and chemical categories. If you are unsure if you must report or require more information, call ht e EPA Emergency Planning and Community Right To Know Hotline:
800-535-0202
End.
Page 4 of 4