Made in Italy ED FACTUR D MANU N A D E ITALY DESIGN ASM AT R A
n째
FLUID TRANSFER EQUIPMENT
601-M
INSTALLATION AND OPERATION SIMPLE AND EFFECTIVE (1:1 RATIO)
2
4
1
3
The slide valve of the air motor sends air (blue) to the left chamber which, pushing the membrane outwards, compressing the previously filled liquid (green). Through the effect of the pressure created valve 1 closes and valve 2 opens allowing the liquid to dispense (green). The right membrane then carries out the same movement by the shaft joining it to the left membrane, creating a vacuum. Through the effect of the vacuum, the valve 3 opens and the valve 4 closes, enabling suction of the liquid (orange).
2
4
1
3
The slide valve of the air motor sends air (blue) to the right chamber which, pushing the membrane outwards, compressing the previously filled liquid (green). Through the effect of the pressure created valve 3 closes and valve 4 opens allowing the liquid to dispense (green). The left membrane then carries out the same movement by the shaft joining it to the right membrane, creating a vacuum. Through the effect of the vacuum, the valve 1 opens and the valve 2 closes, enabling suction of the liquid (orange).
HOW TO INSTALL THE PUMP PUMP INSTALLED ON DRUM
TOP FEED
PUMP INSTALLED ON A MOBILE UNIT
(it is necessary to check the chemical compatibility between pump material and liquid)
SUBMERGED PUMP
BOTTON FEED
BULK TANK
PUMP CONFIGURATION Exploded view of the pump, showing its main parts and thereby facilitating the choice for a custom configuration.
The table summarises the pump configurations available, allowing the user to create his own personalised code whenever the models listed on the leaflet do not meet the specific requirements.
MOTOR INNER FLANGES
PARTS IN CONTACT WITH THE FLUID
MEMBRANE BALLS
PARTS IN CONTACT WITH THE FLUID
Two types of Atex certifications are available, for zone 2 or for zone 1, depending on the materials making up the pump. II 3GD T4 cIIB X (for zone 2) II 2GD T4 cIIB X (for zone 1)
SEATS
The valve seats are to be coupled to the balls and must ensure correct closing. Like the balls, they must be made from a material suitable for the fluid they come into contact with. They open and close the flow of liquid as a result of the reciprocating movement of the follower plates. The material they are made from must be compatible with the fluid being pumped.
They can be threaded (NPT) or flanged, single, multiple and modular.
Defines the inside diameter of the manifold.
This is the heart of the pump, responsible for the reciprocating movement that create the flow of liquid.
MATERIALS AND ATEX VERSIONS
MANIFOLD FOR INLET AND OUTLET
2B = plastic for Zone 2 A/ = NPT threaded connection 3C = aluminium for Zone 1 C/ = mult. NPT threaded con. D/ = connection with flange F/ = multiple modular connection with flange
G/ = dual inlet connection
FLOW INSIDE DIAMETER
They are the only elastic parts of the pump, that suck and pump the liquid with their movement. The material they are made from must be selected in order to obtain the correct chemical compatibility with the liquid to be pumped. These are all the rigid parts such as external flanges, manifolds and sleeves which are constantly in contact with the liquid to be pumped. Available in various materials, depending on the type of liquid. These are not in contact with the pumped liquid, but only with the compressed air feeding the motor. KIND OF MATERIALS
MOTOR
INNER FLANGES
PARTS IN CONTACT WITH THE FLUID
16 = 1/2” 1 = nichel plat. 1 = nichel plat. 1 = nichel plated aluminium aluminium aluminium 26 = 1” 30 = 1.1/4” 7 = polypropylene 40 = 1.1/2” 50 = 2”
MEMBRANE
BALLS
SEATS
E = EPDM H = hytrel N = NBR S = santoprene
A = acetalic H = hytrel S = santoprene T = PTFE
A = acetalic H = hytrel P = polypropylene S = santoprene 1 = cylindrical
T = PTFE + hytrel
acetalic
2 = cylindrical
with flange H/ = dual inlet NPT threaded connection
EXAMPLE 3C1/16111E A A plat. 1 = nichel plat. 1 = nichel plated 3C = aluminium for Zone 1 A/ = NPT threaded connection 16 = 1/2” 1 = nichel E = EPDM aluminium aluminium aluminium
polypropylene
A = acetalic
A = acetalic
Diaphragm pumps R. 1:1 for transfer industrial fluids compatible with the materials of the pumps, made from die-cast aluminium or molding injected Polypropylene, with high quality components, they ensure lasting and reliable operation even in extreme conditions.
1/2” - 16 gpm
1” - 45 gpm
1/2” - 18.5 gpm
1” - 45 gpm
1.1/4” - 52.5 gpm
1.1/2” - 126.5 gpm
2” - 161 gpm
2” - 153 gpm
2” F
MODULAR WITH FLANGE 2”
2.1/2” F
MODULAR WITH FLANGE 2”
1.1/2” F WITH FLANGE 1” 1/2” F
1.1/4” F
WITH FLANGE 1”
1” F 1/2” F
1/2” F
DESIGN Note: The max flow rate shown in the below graphics has been obtained by laboratory test.
3/4” F
Series membrane
Balls for inlet and outlet
TESTING
in EPDM Hytrel NBR Santoprene PTFE+Hytrel ***
1” F
3/4” F
120-PB
Polypropylene - motor Aluminium
P/N 2BC/16117EA1-55
membrane ” P/N 2BC/16117NH2-55 ” P/N 2BC/16117SS2-55 ” P/N 2BC/16117TT2-55 ” P/N 2BC/16117HH2-55
Max. pressure Max cycles per min * Gal per cycle Max suction lift Max size pumpable solids Max working temperature Noise level ** Max air consumption (m3/min) Air working pressure Air inlet connection Air outlet connection (muffler)
EPDM Hytrel NBR Santoprene PTFE+Hytrel
in
3/4” F
120-PB
Polypropylene - motor Aluminium
P/N 2BH/16117EA1-55 P/N 2BH/16117HH2-55 P/N 2BH/16117NH2-55 P/N 2BH/16117SS2-55 P/N 2BH/16117TT2-55
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
120 psi 330 cpm 0.05 gal dry column 15’ - wet column 25’ 0.06” 149° F 75 dB 18 cfm 30 - 90 psi F 3/8” NPT F 1/2” G
120 psi 330 cpm 0.05 gal dry column 15’ - wet column 25’ 0.06” 149° F 75 dB 18 cfm 30 - 90 psi F 3/8” NPT F 1/2” G
Fluid inlet connection
F 3/4” NPT (F 1” NPT for drum)
dual inlet F 3/4” NPT
Fluid outlet connection
F 1/2” NPT
F 1/2” NPT
WITH FLANGE 1” in
1000-PB
Polypropylene - motor Aluminium
P/N 2BD/26117EAA-55 P/N 2BD/26117HHH-55 P/N 2BD/26117NHH-55 P/N 2BD/26117SSS-55 P/N 2BD/26117TTP-55
3/4” F
WITH FLANGE 1”
membrane ” ” ” ”
in
EPDM Hytrel NBR Santoprene PTFE+Hytrel
120 psi 300 cpm 0.15 gal dry column 16.4’ - wet column 25’ 0.12” 149° F 75 dB 57 cfm 30 - 90 psi F 3/8” NPT F 1/2” G ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm) proneness to 1.1/4” thread ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm) proneness to 1.1/4” thread
1000-PB
120-AB
Polypropylene - motor Aluminium
P/N 2BG/26117EAA-55 P/N 2BG/26117HHH-55 P/N 2BG/26117NHH-55 P/N 2BG/26117SSS-55 P/N 2BG/26117TTP-55
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
1.1/4” F 1000-AB
all Aluminium P/N 3CA/16111EAA-55 P/N 3CA/16111HHH-55 P/N 3CA/16111NHH-55 P/N 3CA/16111SSS-55 P/N 3CA/16111TTP-55
120 psi 300 cpm 0.15 gal dry column 16.4’ - wet column 25’ 0.12” 149° F 75 dB 57 cfm 30 - 90 psi F 3/8” NPT F 1/2” G dual inlet ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm) proneness to 1.1/4” thread ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm) proneness to 1.1/4” thread
1.1/4” F 1140-AB
all Aluminium
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
P/N 3CA/26111EAA-55 P/N 3CA/26111HHH-55 P/N 3CA/26111NHH-55 P/N 3CA/26111SSS-55 P/N 3CA/26111TTP-55
2” F 1120-AB
all Aluminium
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
P/N 3CA/30111EAA-55 P/N 3CA/30111HHH-55 P/N 3CA/30111NHH-55 P/N 3CA/30111SSS-55 P/N 3CA/30111TTP-55
2000-AB
all Aluminium
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
2000-AB
all Aluminium
P/N 3CA/40111EAA-55
membrane ” P/N 3CA/40111NHH-55 ” P/N 3CA/40111SSS-55 ” P/N 3CA/40111TTP-55 ” P/N 3CA/40111HHH-55
EPDM Hytrel NBR Santoprene PTFE+Hytrel
all Aluminium
P/N 3CA/50111EAA-55
membrane ” P/N 3CA/50111NHH-55 ” P/N 3CA/50111SSS-55 ” P/N 3CA/50111TTP-55 ” P/N 3CA/50111HHH-55
EPDM Hytrel NBR Santoprene PTFE+Hytrel
P/N 3CF/50111EAA-55 P/N 3CF/50111HHH-55 P/N 3CF/50111NHH-55 P/N 3CF/50111SSS-55 P/N 3CF/50111TTP-55
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
120 psi 400 cpm 0.05 gal dry column 15’ - wet column 25’ 0.06” 212° F 75 dB 21 cfm 30 - 90 psi F 3/8” NPT F 1/2” G
120 psi 300 cpm 0.15 gal dry column 15’ - wet column 25’ 0.12” 212° F 75 dB 57 cfm 30 - 90 psi F 3/8” NPT F 1/2” G
120 psi 260 cpm 0.21 gal dry column 16.4’ - wet column 25’ 0.12” 212° F 75 dB 64 cfm 30 - 90 psi F 3/4” NPT F 1” G
120 psi 220 cpm 0.57 gal dry column 16.4’ - wet column 25’ 0.22” 212° F 78 dB 120 cfm 30 - 90 psi F 3/4” NPT F 1” G
120 psi 147 cpm 1.1 gal dry column 16.4’ - wet column 25’ 0.26” 212° F 82 dB 141 cfm 30 - 90 psi F 3/4” NPT F 1” G
120 psi 147 cpm 1.05 gal dry column 16.4’ - wet column 25’ 0.12” 212° F 82 dB 141 cfm 30 - 90 psi F 3/4” NPT F 1” G
F 3/4” NPT
F 1.1/4” NPT
F 1.1/4” NPT
F 2” NPT
F 2.1/2” NPT
ANSI 150 - DIN PN 10 - JIS 10K 2” (50 mm)
F 1/2” NPT
F 1” NPT
F 1.1/4” NPT
F 1.1/2” NPT
F 2” NPT
ANSI 150 - DIN PN 10 - JIS 10K 2” (50 mm)
Balls for inlet and outlet
ASSEMBLY
A
0 15 (4)
30 (8)
45 (12)
60 (16)
KIND OF FLUID: Water 68 °F SAE30 oil: (ISO VG 100) 68 °F
m3/min
A B
1,6 (56) 1,2 (42) 0,8 (28)
C
0,4 (14) 0 45 (12)
90 (24)
135 (36)
bar (psi)
300 (cfm)
225
2 (29) 0 l/min gpm
lb 110
180 (48)
KIND OF FLUID: Water 68 °F SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min 105
8 (116)
A
6 (87)
B
4 (58)
C
210
420 (cfm) 0,65 A (23)
315
0,49 (17.2)
B
0,32 (11.5)
C
2 (29) 0 l/min gpm
0,16 (5.75) 0 20 (5.4)
40 (10.7)
60 (16)
80 (21)
KIND OF FLUID: Water 68 °F SAE30 oil: (ISO VG 100) 68 °F
bar (psi)
m3/min
cycles/min 75
8 (116)
A
6 (87)
B
4 (58)
C
150
A B
1,6 (56) 1,2 (42) 0,8 (28)
C
2 (29) 0 l/min gpm
0,4 (14) 0 45 (12)
90 (24)
135 (36)
bar (psi)
300 (cfm)
225
180 (48)
KIND OF FLUID: Water 68 °F SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min 65
8 (116)
A
6 (87)
B
4 (58)
C
130
1,8 (64)
A B
1,35 (48) 0,9 (32)
C
2 (29) 0 l/min gpm
0,45 (16) 0 50 (13)
100 (26)
150 (40)
bar (psi)
260 (cfm)
195
200 (52)
KIND OF FLUID: Water 68 °F SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min 55
8 (116)
A
6 (87)
B
4 (58)
C
110
A B
3,4 (120) 2,55 (90) 1,7 (60)
C
2 (29) 0 l/min gpm
0,85 (30) 0 120 (32)
240 (64)
360 (96)
bar (psi)
220 (cfm)
165
480 (128)
KIND OF FLUID: Water 68 °F
m3/min
cycles/min 38
8 (116)
A
6 (87)
B
4 (58)
C
75
4 (140)
A B
3 (105) 2 (70)
C
2 (29) 0 l/min gpm
1 (35) 0 155 (41.5)
310 (83)
465 (125)
bar (psi)
150 (cfm)
113
620 (166)
KIND OF FLUID: Water 68 °F
m3/min
cycles/min 38
75
150 (cfm)
113
8 (116)
A
A
4 (140)
6 (87)
B
B
3 (105)
4 (58)
C
2 (70)
C
2 (29) 0 l/min gpm
1 (35) 0 150 (40)
300 (80)
450 (120)
600 (160)
KIND OF FLUID: Water 68 °F
AIR CONSUMPTION
C
N° 1 packing cf 5.6
FLUID OUTLET PRESSURE
0,13 (4.7)
4 (58)
lb 95
AIR CONSUMPTION
2 (29) 0 l/min gpm
B
0,27 (9.5)
C
B
16.1” x 17” x 28”
N° 1 packing cf 5.6
FLUID OUTLET PRESSURE
C
6 (87)
18.2” x 17” x 24.2”
lb 56
AIR CONSUMPTION
4 (58)
0,4 (14.2)
N° 1 packing cf 2.3
FLUID OUTLET PRESSURE
4 bar (58 psi)
B
13.8” x 15.8” x 20.2” lb 42
AIR CONSUMPTION
C
B
N° 1 packing cf 1.35
FLUID OUTLET PRESSURE
C
6 (87)
A
11.3” x 9.4” x 15.2” lb 30
AIR CONSUMPTION
6 bar (87 psi)
8 (116)
150
N° 1 packing cf 0.9
*** With PTFE membrane flow rate is 10 % lower
cycles/min 75
10.3” x 7.9” x 13.6” lb 17.6
FLUID OUTLET PRESSURE
B
A
340 (cfm) 0,53 A (19)
N° 1 packing cf 0.5
AIR CONSUMPTION
B
8 (116)
255
7.9” x 6.3” x 10” lb 26.5
FLUID OUTLET PRESSURE
8 bar (116 psi)
170
bar (psi)
m3/min
cycles/min 85
FLUID OUTLET PRESSURE
A
FLUID OUTLET PRESSURE
C
A
bar (psi)
AIR CONSUMPTION
PUMP AIR FEEDING PRESSURE
14” x 7.8” x 16.5” N° 1 packing cf 0.9
AIR CONSUMPTION
Overall dimensions (A x B x C) 8.6” x 7” x 12.8” 8.6” x 7” x 12.8” 11.8” x 7.9” x 17.9” Packing - Weight N° 1 packing cf 0.9 lb 26 N° 1 packing cf 0.5 lb 15.4 N° 1 packing cf 0.5 lb 15.4 ** Different kind of muffler are available on request for special use or hard work * Displacement per cycle may be influenced by suction lift, fluid viscosity, air pressure, number of cycles per minute
Diaphragm pumps R. 1:1 for transfer industrial fluids compatible with the materials of the pumps, made from die-cast aluminium or molding injected Polypropylene, with high quality components, they ensure lasting and reliable operation even in extreme conditions.
1/2” - 16 gpm
1” - 45 gpm
1/2” - 18.5 gpm
1” - 45 gpm
1.1/4” - 52.5 gpm
1.1/2” - 126.5 gpm
2” - 161 gpm
2” - 153 gpm
2” F
MODULAR WITH FLANGE 2”
2.1/2” F
MODULAR WITH FLANGE 2”
1.1/2” F WITH FLANGE 1” 1/2” F
1.1/4” F
WITH FLANGE 1”
1” F 1/2” F
1/2” F
DESIGN Note: The max flow rate shown in the below graphics has been obtained by laboratory test.
3/4” F
Series membrane
Balls for inlet and outlet
TESTING
in EPDM Hytrel NBR Santoprene PTFE+Hytrel ***
1” F
3/4” F
120-PB
Polypropylene - motor Aluminium
P/N 2BC/16117EA1-55
membrane ” P/N 2BC/16117NH2-55 ” P/N 2BC/16117SS2-55 ” P/N 2BC/16117TT2-55 ” P/N 2BC/16117HH2-55
Max. pressure Max cycles per min * Gal per cycle Max suction lift Max size pumpable solids Max working temperature Noise level ** Max air consumption (m3/min) Air working pressure Air inlet connection Air outlet connection (muffler)
EPDM Hytrel NBR Santoprene PTFE+Hytrel
in
3/4” F
120-PB
Polypropylene - motor Aluminium
P/N 2BH/16117EA1-55 P/N 2BH/16117HH2-55 P/N 2BH/16117NH2-55 P/N 2BH/16117SS2-55 P/N 2BH/16117TT2-55
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
120 psi 330 cpm 0.05 gal dry column 15’ - wet column 25’ 0.06” 149° F 75 dB 18 cfm 30 - 90 psi F 3/8” NPT F 1/2” G
120 psi 330 cpm 0.05 gal dry column 15’ - wet column 25’ 0.06” 149° F 75 dB 18 cfm 30 - 90 psi F 3/8” NPT F 1/2” G
Fluid inlet connection
F 3/4” NPT (F 1” NPT for drum)
dual inlet F 3/4” NPT
Fluid outlet connection
F 1/2” NPT
F 1/2” NPT
WITH FLANGE 1” in
1000-PB
Polypropylene - motor Aluminium
P/N 2BD/26117EAA-55 P/N 2BD/26117HHH-55 P/N 2BD/26117NHH-55 P/N 2BD/26117SSS-55 P/N 2BD/26117TTP-55
3/4” F
WITH FLANGE 1”
membrane ” ” ” ”
in
EPDM Hytrel NBR Santoprene PTFE+Hytrel
120 psi 300 cpm 0.15 gal dry column 16.4’ - wet column 25’ 0.12” 149° F 75 dB 57 cfm 30 - 90 psi F 3/8” NPT F 1/2” G ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm) proneness to 1.1/4” thread ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm) proneness to 1.1/4” thread
1000-PB
120-AB
Polypropylene - motor Aluminium
P/N 2BG/26117EAA-55 P/N 2BG/26117HHH-55 P/N 2BG/26117NHH-55 P/N 2BG/26117SSS-55 P/N 2BG/26117TTP-55
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
1.1/4” F 1000-AB
all Aluminium P/N 3CA/16111EAA-55 P/N 3CA/16111HHH-55 P/N 3CA/16111NHH-55 P/N 3CA/16111SSS-55 P/N 3CA/16111TTP-55
120 psi 300 cpm 0.15 gal dry column 16.4’ - wet column 25’ 0.12” 149° F 75 dB 57 cfm 30 - 90 psi F 3/8” NPT F 1/2” G dual inlet ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm) proneness to 1.1/4” thread ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm) proneness to 1.1/4” thread
1.1/4” F 1140-AB
all Aluminium
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
P/N 3CA/26111EAA-55 P/N 3CA/26111HHH-55 P/N 3CA/26111NHH-55 P/N 3CA/26111SSS-55 P/N 3CA/26111TTP-55
2” F 1120-AB
all Aluminium
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
P/N 3CA/30111EAA-55 P/N 3CA/30111HHH-55 P/N 3CA/30111NHH-55 P/N 3CA/30111SSS-55 P/N 3CA/30111TTP-55
2000-AB
all Aluminium
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
2000-AB
all Aluminium
P/N 3CA/40111EAA-55
membrane ” P/N 3CA/40111NHH-55 ” P/N 3CA/40111SSS-55 ” P/N 3CA/40111TTP-55 ” P/N 3CA/40111HHH-55
EPDM Hytrel NBR Santoprene PTFE+Hytrel
all Aluminium
P/N 3CA/50111EAA-55
membrane ” P/N 3CA/50111NHH-55 ” P/N 3CA/50111SSS-55 ” P/N 3CA/50111TTP-55 ” P/N 3CA/50111HHH-55
EPDM Hytrel NBR Santoprene PTFE+Hytrel
P/N 3CF/50111EAA-55 P/N 3CF/50111HHH-55 P/N 3CF/50111NHH-55 P/N 3CF/50111SSS-55 P/N 3CF/50111TTP-55
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
120 psi 400 cpm 0.05 gal dry column 15’ - wet column 25’ 0.06” 212° F 75 dB 21 cfm 30 - 90 psi F 3/8” NPT F 1/2” G
120 psi 300 cpm 0.15 gal dry column 15’ - wet column 25’ 0.12” 212° F 75 dB 57 cfm 30 - 90 psi F 3/8” NPT F 1/2” G
120 psi 260 cpm 0.21 gal dry column 16.4’ - wet column 25’ 0.12” 212° F 75 dB 64 cfm 30 - 90 psi F 3/4” NPT F 1” G
120 psi 220 cpm 0.57 gal dry column 16.4’ - wet column 25’ 0.22” 212° F 78 dB 120 cfm 30 - 90 psi F 3/4” NPT F 1” G
120 psi 147 cpm 1.1 gal dry column 16.4’ - wet column 25’ 0.26” 212° F 82 dB 141 cfm 30 - 90 psi F 3/4” NPT F 1” G
120 psi 147 cpm 1.05 gal dry column 16.4’ - wet column 25’ 0.12” 212° F 82 dB 141 cfm 30 - 90 psi F 3/4” NPT F 1” G
F 3/4” NPT
F 1.1/4” NPT
F 1.1/4” NPT
F 2” NPT
F 2.1/2” NPT
ANSI 150 - DIN PN 10 - JIS 10K 2” (50 mm)
F 1/2” NPT
F 1” NPT
F 1.1/4” NPT
F 1.1/2” NPT
F 2” NPT
ANSI 150 - DIN PN 10 - JIS 10K 2” (50 mm)
Balls for inlet and outlet
ASSEMBLY
A
0 15 (4)
30 (8)
45 (12)
60 (16)
KIND OF FLUID: Water 68 °F SAE30 oil: (ISO VG 100) 68 °F
m3/min
A B
1,6 (56) 1,2 (42) 0,8 (28)
C
0,4 (14) 0 45 (12)
90 (24)
135 (36)
bar (psi)
300 (cfm)
225
2 (29) 0 l/min gpm
lb 110
180 (48)
KIND OF FLUID: Water 68 °F SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min 105
8 (116)
A
6 (87)
B
4 (58)
C
210
420 (cfm) 0,65 A (23)
315
0,49 (17.2)
B
0,32 (11.5)
C
2 (29) 0 l/min gpm
0,16 (5.75) 0 20 (5.4)
40 (10.7)
60 (16)
80 (21)
KIND OF FLUID: Water 68 °F SAE30 oil: (ISO VG 100) 68 °F
bar (psi)
m3/min
cycles/min 75
8 (116)
A
6 (87)
B
4 (58)
C
150
A B
1,6 (56) 1,2 (42) 0,8 (28)
C
2 (29) 0 l/min gpm
0,4 (14) 0 45 (12)
90 (24)
135 (36)
bar (psi)
300 (cfm)
225
180 (48)
KIND OF FLUID: Water 68 °F SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min 65
8 (116)
A
6 (87)
B
4 (58)
C
130
1,8 (64)
A B
1,35 (48) 0,9 (32)
C
2 (29) 0 l/min gpm
0,45 (16) 0 50 (13)
100 (26)
150 (40)
bar (psi)
260 (cfm)
195
200 (52)
KIND OF FLUID: Water 68 °F SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min 55
8 (116)
A
6 (87)
B
4 (58)
C
110
A B
3,4 (120) 2,55 (90) 1,7 (60)
C
2 (29) 0 l/min gpm
0,85 (30) 0 120 (32)
240 (64)
360 (96)
bar (psi)
220 (cfm)
165
480 (128)
KIND OF FLUID: Water 68 °F
m3/min
cycles/min 38
8 (116)
A
6 (87)
B
4 (58)
C
75
4 (140)
A B
3 (105) 2 (70)
C
2 (29) 0 l/min gpm
1 (35) 0 155 (41.5)
310 (83)
465 (125)
bar (psi)
150 (cfm)
113
620 (166)
KIND OF FLUID: Water 68 °F
m3/min
cycles/min 38
75
150 (cfm)
113
8 (116)
A
A
4 (140)
6 (87)
B
B
3 (105)
4 (58)
C
2 (70)
C
2 (29) 0 l/min gpm
1 (35) 0 150 (40)
300 (80)
450 (120)
600 (160)
KIND OF FLUID: Water 68 °F
AIR CONSUMPTION
C
N° 1 packing cf 5.6
FLUID OUTLET PRESSURE
0,13 (4.7)
4 (58)
lb 95
AIR CONSUMPTION
2 (29) 0 l/min gpm
B
0,27 (9.5)
C
B
16.1” x 17” x 28”
N° 1 packing cf 5.6
FLUID OUTLET PRESSURE
C
6 (87)
18.2” x 17” x 24.2”
lb 56
AIR CONSUMPTION
4 (58)
0,4 (14.2)
N° 1 packing cf 2.3
FLUID OUTLET PRESSURE
4 bar (58 psi)
B
13.8” x 15.8” x 20.2” lb 42
AIR CONSUMPTION
C
B
N° 1 packing cf 1.35
FLUID OUTLET PRESSURE
C
6 (87)
A
11.3” x 9.4” x 15.2” lb 30
AIR CONSUMPTION
6 bar (87 psi)
8 (116)
150
N° 1 packing cf 0.9
*** With PTFE membrane flow rate is 10 % lower
cycles/min 75
10.3” x 7.9” x 13.6” lb 17.6
FLUID OUTLET PRESSURE
B
A
340 (cfm) 0,53 A (19)
N° 1 packing cf 0.5
AIR CONSUMPTION
B
8 (116)
255
7.9” x 6.3” x 10” lb 26.5
FLUID OUTLET PRESSURE
8 bar (116 psi)
170
bar (psi)
m3/min
cycles/min 85
FLUID OUTLET PRESSURE
A
FLUID OUTLET PRESSURE
C
A
bar (psi)
AIR CONSUMPTION
PUMP AIR FEEDING PRESSURE
14” x 7.8” x 16.5” N° 1 packing cf 0.9
AIR CONSUMPTION
Overall dimensions (A x B x C) 8.6” x 7” x 12.8” 8.6” x 7” x 12.8” 11.8” x 7.9” x 17.9” Packing - Weight N° 1 packing cf 0.9 lb 26 N° 1 packing cf 0.5 lb 15.4 N° 1 packing cf 0.5 lb 15.4 ** Different kind of muffler are available on request for special use or hard work * Displacement per cycle may be influenced by suction lift, fluid viscosity, air pressure, number of cycles per minute
Diaphragm pumps R. 1:1 for transfer industrial fluids compatible with the materials of the pumps, made from die-cast aluminium or molding injected Polypropylene, with high quality components, they ensure lasting and reliable operation even in extreme conditions.
1/2” - 16 gpm
1” - 45 gpm
1/2” - 18.5 gpm
1” - 45 gpm
1.1/4” - 52.5 gpm
1.1/2” - 126.5 gpm
2” - 161 gpm
2” - 153 gpm
2” F
MODULAR WITH FLANGE 2”
2.1/2” F
MODULAR WITH FLANGE 2”
1.1/2” F WITH FLANGE 1” 1/2” F
1.1/4” F
WITH FLANGE 1”
1” F 1/2” F
1/2” F
DESIGN Note: The max flow rate shown in the below graphics has been obtained by laboratory test.
3/4” F
Series membrane
Balls for inlet and outlet
TESTING
in EPDM Hytrel NBR Santoprene PTFE+Hytrel ***
1” F
3/4” F
120-PB
Polypropylene - motor Aluminium
P/N 2BC/16117EA1-55
membrane ” P/N 2BC/16117NH2-55 ” P/N 2BC/16117SS2-55 ” P/N 2BC/16117TT2-55 ” P/N 2BC/16117HH2-55
Max. pressure Max cycles per min * Gal per cycle Max suction lift Max size pumpable solids Max working temperature Noise level ** Max air consumption (m3/min) Air working pressure Air inlet connection Air outlet connection (muffler)
EPDM Hytrel NBR Santoprene PTFE+Hytrel
in
3/4” F
120-PB
Polypropylene - motor Aluminium
P/N 2BH/16117EA1-55 P/N 2BH/16117HH2-55 P/N 2BH/16117NH2-55 P/N 2BH/16117SS2-55 P/N 2BH/16117TT2-55
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
120 psi 330 cpm 0.05 gal dry column 15’ - wet column 25’ 0.06” 149° F 75 dB 18 cfm 30 - 90 psi F 3/8” NPT F 1/2” G
120 psi 330 cpm 0.05 gal dry column 15’ - wet column 25’ 0.06” 149° F 75 dB 18 cfm 30 - 90 psi F 3/8” NPT F 1/2” G
Fluid inlet connection
F 3/4” NPT (F 1” NPT for drum)
dual inlet F 3/4” NPT
Fluid outlet connection
F 1/2” NPT
F 1/2” NPT
WITH FLANGE 1” in
1000-PB
Polypropylene - motor Aluminium
P/N 2BD/26117EAA-55 P/N 2BD/26117HHH-55 P/N 2BD/26117NHH-55 P/N 2BD/26117SSS-55 P/N 2BD/26117TTP-55
3/4” F
WITH FLANGE 1”
membrane ” ” ” ”
in
EPDM Hytrel NBR Santoprene PTFE+Hytrel
120 psi 300 cpm 0.15 gal dry column 16.4’ - wet column 25’ 0.12” 149° F 75 dB 57 cfm 30 - 90 psi F 3/8” NPT F 1/2” G ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm) proneness to 1.1/4” thread ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm) proneness to 1.1/4” thread
1000-PB
120-AB
Polypropylene - motor Aluminium
P/N 2BG/26117EAA-55 P/N 2BG/26117HHH-55 P/N 2BG/26117NHH-55 P/N 2BG/26117SSS-55 P/N 2BG/26117TTP-55
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
1.1/4” F 1000-AB
all Aluminium P/N 3CA/16111EAA-55 P/N 3CA/16111HHH-55 P/N 3CA/16111NHH-55 P/N 3CA/16111SSS-55 P/N 3CA/16111TTP-55
120 psi 300 cpm 0.15 gal dry column 16.4’ - wet column 25’ 0.12” 149° F 75 dB 57 cfm 30 - 90 psi F 3/8” NPT F 1/2” G dual inlet ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm) proneness to 1.1/4” thread ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm) proneness to 1.1/4” thread
1.1/4” F 1140-AB
all Aluminium
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
P/N 3CA/26111EAA-55 P/N 3CA/26111HHH-55 P/N 3CA/26111NHH-55 P/N 3CA/26111SSS-55 P/N 3CA/26111TTP-55
2” F 1120-AB
all Aluminium
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
P/N 3CA/30111EAA-55 P/N 3CA/30111HHH-55 P/N 3CA/30111NHH-55 P/N 3CA/30111SSS-55 P/N 3CA/30111TTP-55
2000-AB
all Aluminium
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
2000-AB
all Aluminium
P/N 3CA/40111EAA-55
membrane ” P/N 3CA/40111NHH-55 ” P/N 3CA/40111SSS-55 ” P/N 3CA/40111TTP-55 ” P/N 3CA/40111HHH-55
EPDM Hytrel NBR Santoprene PTFE+Hytrel
all Aluminium
P/N 3CA/50111EAA-55
membrane ” P/N 3CA/50111NHH-55 ” P/N 3CA/50111SSS-55 ” P/N 3CA/50111TTP-55 ” P/N 3CA/50111HHH-55
EPDM Hytrel NBR Santoprene PTFE+Hytrel
P/N 3CF/50111EAA-55 P/N 3CF/50111HHH-55 P/N 3CF/50111NHH-55 P/N 3CF/50111SSS-55 P/N 3CF/50111TTP-55
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
120 psi 400 cpm 0.05 gal dry column 15’ - wet column 25’ 0.06” 212° F 75 dB 21 cfm 30 - 90 psi F 3/8” NPT F 1/2” G
120 psi 300 cpm 0.15 gal dry column 15’ - wet column 25’ 0.12” 212° F 75 dB 57 cfm 30 - 90 psi F 3/8” NPT F 1/2” G
120 psi 260 cpm 0.21 gal dry column 16.4’ - wet column 25’ 0.12” 212° F 75 dB 64 cfm 30 - 90 psi F 3/4” NPT F 1” G
120 psi 220 cpm 0.57 gal dry column 16.4’ - wet column 25’ 0.22” 212° F 78 dB 120 cfm 30 - 90 psi F 3/4” NPT F 1” G
120 psi 147 cpm 1.1 gal dry column 16.4’ - wet column 25’ 0.26” 212° F 82 dB 141 cfm 30 - 90 psi F 3/4” NPT F 1” G
120 psi 147 cpm 1.05 gal dry column 16.4’ - wet column 25’ 0.12” 212° F 82 dB 141 cfm 30 - 90 psi F 3/4” NPT F 1” G
F 3/4” NPT
F 1.1/4” NPT
F 1.1/4” NPT
F 2” NPT
F 2.1/2” NPT
ANSI 150 - DIN PN 10 - JIS 10K 2” (50 mm)
F 1/2” NPT
F 1” NPT
F 1.1/4” NPT
F 1.1/2” NPT
F 2” NPT
ANSI 150 - DIN PN 10 - JIS 10K 2” (50 mm)
Balls for inlet and outlet
ASSEMBLY
A
0 15 (4)
30 (8)
45 (12)
60 (16)
KIND OF FLUID: Water 68 °F SAE30 oil: (ISO VG 100) 68 °F
m3/min
A B
1,6 (56) 1,2 (42) 0,8 (28)
C
0,4 (14) 0 45 (12)
90 (24)
135 (36)
bar (psi)
300 (cfm)
225
2 (29) 0 l/min gpm
lb 110
180 (48)
KIND OF FLUID: Water 68 °F SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min 105
8 (116)
A
6 (87)
B
4 (58)
C
210
420 (cfm) 0,65 A (23)
315
0,49 (17.2)
B
0,32 (11.5)
C
2 (29) 0 l/min gpm
0,16 (5.75) 0 20 (5.4)
40 (10.7)
60 (16)
80 (21)
KIND OF FLUID: Water 68 °F SAE30 oil: (ISO VG 100) 68 °F
bar (psi)
m3/min
cycles/min 75
8 (116)
A
6 (87)
B
4 (58)
C
150
A B
1,6 (56) 1,2 (42) 0,8 (28)
C
2 (29) 0 l/min gpm
0,4 (14) 0 45 (12)
90 (24)
135 (36)
bar (psi)
300 (cfm)
225
180 (48)
KIND OF FLUID: Water 68 °F SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min 65
8 (116)
A
6 (87)
B
4 (58)
C
130
1,8 (64)
A B
1,35 (48) 0,9 (32)
C
2 (29) 0 l/min gpm
0,45 (16) 0 50 (13)
100 (26)
150 (40)
bar (psi)
260 (cfm)
195
200 (52)
KIND OF FLUID: Water 68 °F SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min 55
8 (116)
A
6 (87)
B
4 (58)
C
110
A B
3,4 (120) 2,55 (90) 1,7 (60)
C
2 (29) 0 l/min gpm
0,85 (30) 0 120 (32)
240 (64)
360 (96)
bar (psi)
220 (cfm)
165
480 (128)
KIND OF FLUID: Water 68 °F
m3/min
cycles/min 38
8 (116)
A
6 (87)
B
4 (58)
C
75
4 (140)
A B
3 (105) 2 (70)
C
2 (29) 0 l/min gpm
1 (35) 0 155 (41.5)
310 (83)
465 (125)
bar (psi)
150 (cfm)
113
620 (166)
KIND OF FLUID: Water 68 °F
m3/min
cycles/min 38
75
150 (cfm)
113
8 (116)
A
A
4 (140)
6 (87)
B
B
3 (105)
4 (58)
C
2 (70)
C
2 (29) 0 l/min gpm
1 (35) 0 150 (40)
300 (80)
450 (120)
600 (160)
KIND OF FLUID: Water 68 °F
AIR CONSUMPTION
C
N° 1 packing cf 5.6
FLUID OUTLET PRESSURE
0,13 (4.7)
4 (58)
lb 95
AIR CONSUMPTION
2 (29) 0 l/min gpm
B
0,27 (9.5)
C
B
16.1” x 17” x 28”
N° 1 packing cf 5.6
FLUID OUTLET PRESSURE
C
6 (87)
18.2” x 17” x 24.2”
lb 56
AIR CONSUMPTION
4 (58)
0,4 (14.2)
N° 1 packing cf 2.3
FLUID OUTLET PRESSURE
4 bar (58 psi)
B
13.8” x 15.8” x 20.2” lb 42
AIR CONSUMPTION
C
B
N° 1 packing cf 1.35
FLUID OUTLET PRESSURE
C
6 (87)
A
11.3” x 9.4” x 15.2” lb 30
AIR CONSUMPTION
6 bar (87 psi)
8 (116)
150
N° 1 packing cf 0.9
*** With PTFE membrane flow rate is 10 % lower
cycles/min 75
10.3” x 7.9” x 13.6” lb 17.6
FLUID OUTLET PRESSURE
B
A
340 (cfm) 0,53 A (19)
N° 1 packing cf 0.5
AIR CONSUMPTION
B
8 (116)
255
7.9” x 6.3” x 10” lb 26.5
FLUID OUTLET PRESSURE
8 bar (116 psi)
170
bar (psi)
m3/min
cycles/min 85
FLUID OUTLET PRESSURE
A
FLUID OUTLET PRESSURE
C
A
bar (psi)
AIR CONSUMPTION
PUMP AIR FEEDING PRESSURE
14” x 7.8” x 16.5” N° 1 packing cf 0.9
AIR CONSUMPTION
Overall dimensions (A x B x C) 8.6” x 7” x 12.8” 8.6” x 7” x 12.8” 11.8” x 7.9” x 17.9” Packing - Weight N° 1 packing cf 0.9 lb 26 N° 1 packing cf 0.5 lb 15.4 N° 1 packing cf 0.5 lb 15.4 ** Different kind of muffler are available on request for special use or hard work * Displacement per cycle may be influenced by suction lift, fluid viscosity, air pressure, number of cycles per minute
Diaphragm pumps R. 1:1 for transfer industrial fluids compatible with the materials of the pumps, made from die-cast aluminium or molding injected Polypropylene, with high quality components, they ensure lasting and reliable operation even in extreme conditions.
1/2” - 16 gpm
1” - 45 gpm
1/2” - 18.5 gpm
1” - 45 gpm
1.1/4” - 52.5 gpm
1.1/2” - 126.5 gpm
2” - 161 gpm
2” - 153 gpm
2” F
MODULAR WITH FLANGE 2”
2.1/2” F
MODULAR WITH FLANGE 2”
1.1/2” F WITH FLANGE 1” 1/2” F
1.1/4” F
WITH FLANGE 1”
1” F 1/2” F
1/2” F
DESIGN Note: The max flow rate shown in the below graphics has been obtained by laboratory test.
3/4” F
Series membrane
Balls for inlet and outlet
TESTING
in EPDM Hytrel NBR Santoprene PTFE+Hytrel ***
1” F
3/4” F
120-PB
Polypropylene - motor Aluminium
P/N 2BC/16117EA1-55
membrane ” P/N 2BC/16117NH2-55 ” P/N 2BC/16117SS2-55 ” P/N 2BC/16117TT2-55 ” P/N 2BC/16117HH2-55
Max. pressure Max cycles per min * Gal per cycle Max suction lift Max size pumpable solids Max working temperature Noise level ** Max air consumption (m3/min) Air working pressure Air inlet connection Air outlet connection (muffler)
EPDM Hytrel NBR Santoprene PTFE+Hytrel
in
3/4” F
120-PB
Polypropylene - motor Aluminium
P/N 2BH/16117EA1-55 P/N 2BH/16117HH2-55 P/N 2BH/16117NH2-55 P/N 2BH/16117SS2-55 P/N 2BH/16117TT2-55
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
120 psi 330 cpm 0.05 gal dry column 15’ - wet column 25’ 0.06” 149° F 75 dB 18 cfm 30 - 90 psi F 3/8” NPT F 1/2” G
120 psi 330 cpm 0.05 gal dry column 15’ - wet column 25’ 0.06” 149° F 75 dB 18 cfm 30 - 90 psi F 3/8” NPT F 1/2” G
Fluid inlet connection
F 3/4” NPT (F 1” NPT for drum)
dual inlet F 3/4” NPT
Fluid outlet connection
F 1/2” NPT
F 1/2” NPT
WITH FLANGE 1” in
1000-PB
Polypropylene - motor Aluminium
P/N 2BD/26117EAA-55 P/N 2BD/26117HHH-55 P/N 2BD/26117NHH-55 P/N 2BD/26117SSS-55 P/N 2BD/26117TTP-55
3/4” F
WITH FLANGE 1”
membrane ” ” ” ”
in
EPDM Hytrel NBR Santoprene PTFE+Hytrel
120 psi 300 cpm 0.15 gal dry column 16.4’ - wet column 25’ 0.12” 149° F 75 dB 57 cfm 30 - 90 psi F 3/8” NPT F 1/2” G ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm) proneness to 1.1/4” thread ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm) proneness to 1.1/4” thread
1000-PB
120-AB
Polypropylene - motor Aluminium
P/N 2BG/26117EAA-55 P/N 2BG/26117HHH-55 P/N 2BG/26117NHH-55 P/N 2BG/26117SSS-55 P/N 2BG/26117TTP-55
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
1.1/4” F 1000-AB
all Aluminium P/N 3CA/16111EAA-55 P/N 3CA/16111HHH-55 P/N 3CA/16111NHH-55 P/N 3CA/16111SSS-55 P/N 3CA/16111TTP-55
120 psi 300 cpm 0.15 gal dry column 16.4’ - wet column 25’ 0.12” 149° F 75 dB 57 cfm 30 - 90 psi F 3/8” NPT F 1/2” G dual inlet ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm) proneness to 1.1/4” thread ANSI 150 - DIN PN 10 - JIS 10K 1” (25 mm) proneness to 1.1/4” thread
1.1/4” F 1140-AB
all Aluminium
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
P/N 3CA/26111EAA-55 P/N 3CA/26111HHH-55 P/N 3CA/26111NHH-55 P/N 3CA/26111SSS-55 P/N 3CA/26111TTP-55
2” F 1120-AB
all Aluminium
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
P/N 3CA/30111EAA-55 P/N 3CA/30111HHH-55 P/N 3CA/30111NHH-55 P/N 3CA/30111SSS-55 P/N 3CA/30111TTP-55
2000-AB
all Aluminium
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
2000-AB
all Aluminium
P/N 3CA/40111EAA-55
membrane ” P/N 3CA/40111NHH-55 ” P/N 3CA/40111SSS-55 ” P/N 3CA/40111TTP-55 ” P/N 3CA/40111HHH-55
EPDM Hytrel NBR Santoprene PTFE+Hytrel
all Aluminium
P/N 3CA/50111EAA-55
membrane ” P/N 3CA/50111NHH-55 ” P/N 3CA/50111SSS-55 ” P/N 3CA/50111TTP-55 ” P/N 3CA/50111HHH-55
EPDM Hytrel NBR Santoprene PTFE+Hytrel
P/N 3CF/50111EAA-55 P/N 3CF/50111HHH-55 P/N 3CF/50111NHH-55 P/N 3CF/50111SSS-55 P/N 3CF/50111TTP-55
membrane ” ” ” ”
EPDM Hytrel NBR Santoprene PTFE+Hytrel
120 psi 400 cpm 0.05 gal dry column 15’ - wet column 25’ 0.06” 212° F 75 dB 21 cfm 30 - 90 psi F 3/8” NPT F 1/2” G
120 psi 300 cpm 0.15 gal dry column 15’ - wet column 25’ 0.12” 212° F 75 dB 57 cfm 30 - 90 psi F 3/8” NPT F 1/2” G
120 psi 260 cpm 0.21 gal dry column 16.4’ - wet column 25’ 0.12” 212° F 75 dB 64 cfm 30 - 90 psi F 3/4” NPT F 1” G
120 psi 220 cpm 0.57 gal dry column 16.4’ - wet column 25’ 0.22” 212° F 78 dB 120 cfm 30 - 90 psi F 3/4” NPT F 1” G
120 psi 147 cpm 1.1 gal dry column 16.4’ - wet column 25’ 0.26” 212° F 82 dB 141 cfm 30 - 90 psi F 3/4” NPT F 1” G
120 psi 147 cpm 1.05 gal dry column 16.4’ - wet column 25’ 0.12” 212° F 82 dB 141 cfm 30 - 90 psi F 3/4” NPT F 1” G
F 3/4” NPT
F 1.1/4” NPT
F 1.1/4” NPT
F 2” NPT
F 2.1/2” NPT
ANSI 150 - DIN PN 10 - JIS 10K 2” (50 mm)
F 1/2” NPT
F 1” NPT
F 1.1/4” NPT
F 1.1/2” NPT
F 2” NPT
ANSI 150 - DIN PN 10 - JIS 10K 2” (50 mm)
Balls for inlet and outlet
ASSEMBLY
A
0 15 (4)
30 (8)
45 (12)
60 (16)
KIND OF FLUID: Water 68 °F SAE30 oil: (ISO VG 100) 68 °F
m3/min
A B
1,6 (56) 1,2 (42) 0,8 (28)
C
0,4 (14) 0 45 (12)
90 (24)
135 (36)
bar (psi)
300 (cfm)
225
2 (29) 0 l/min gpm
lb 110
180 (48)
KIND OF FLUID: Water 68 °F SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min 105
8 (116)
A
6 (87)
B
4 (58)
C
210
420 (cfm) 0,65 A (23)
315
0,49 (17.2)
B
0,32 (11.5)
C
2 (29) 0 l/min gpm
0,16 (5.75) 0 20 (5.4)
40 (10.7)
60 (16)
80 (21)
KIND OF FLUID: Water 68 °F SAE30 oil: (ISO VG 100) 68 °F
bar (psi)
m3/min
cycles/min 75
8 (116)
A
6 (87)
B
4 (58)
C
150
A B
1,6 (56) 1,2 (42) 0,8 (28)
C
2 (29) 0 l/min gpm
0,4 (14) 0 45 (12)
90 (24)
135 (36)
bar (psi)
300 (cfm)
225
180 (48)
KIND OF FLUID: Water 68 °F SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min 65
8 (116)
A
6 (87)
B
4 (58)
C
130
1,8 (64)
A B
1,35 (48) 0,9 (32)
C
2 (29) 0 l/min gpm
0,45 (16) 0 50 (13)
100 (26)
150 (40)
bar (psi)
260 (cfm)
195
200 (52)
KIND OF FLUID: Water 68 °F SAE30 oil: (ISO VG 100) 68 °F
m3/min
cycles/min 55
8 (116)
A
6 (87)
B
4 (58)
C
110
A B
3,4 (120) 2,55 (90) 1,7 (60)
C
2 (29) 0 l/min gpm
0,85 (30) 0 120 (32)
240 (64)
360 (96)
bar (psi)
220 (cfm)
165
480 (128)
KIND OF FLUID: Water 68 °F
m3/min
cycles/min 38
8 (116)
A
6 (87)
B
4 (58)
C
75
4 (140)
A B
3 (105) 2 (70)
C
2 (29) 0 l/min gpm
1 (35) 0 155 (41.5)
310 (83)
465 (125)
bar (psi)
150 (cfm)
113
620 (166)
KIND OF FLUID: Water 68 °F
m3/min
cycles/min 38
75
150 (cfm)
113
8 (116)
A
A
4 (140)
6 (87)
B
B
3 (105)
4 (58)
C
2 (70)
C
2 (29) 0 l/min gpm
1 (35) 0 150 (40)
300 (80)
450 (120)
600 (160)
KIND OF FLUID: Water 68 °F
AIR CONSUMPTION
C
N° 1 packing cf 5.6
FLUID OUTLET PRESSURE
0,13 (4.7)
4 (58)
lb 95
AIR CONSUMPTION
2 (29) 0 l/min gpm
B
0,27 (9.5)
C
B
16.1” x 17” x 28”
N° 1 packing cf 5.6
FLUID OUTLET PRESSURE
C
6 (87)
18.2” x 17” x 24.2”
lb 56
AIR CONSUMPTION
4 (58)
0,4 (14.2)
N° 1 packing cf 2.3
FLUID OUTLET PRESSURE
4 bar (58 psi)
B
13.8” x 15.8” x 20.2” lb 42
AIR CONSUMPTION
C
B
N° 1 packing cf 1.35
FLUID OUTLET PRESSURE
C
6 (87)
A
11.3” x 9.4” x 15.2” lb 30
AIR CONSUMPTION
6 bar (87 psi)
8 (116)
150
N° 1 packing cf 0.9
*** With PTFE membrane flow rate is 10 % lower
cycles/min 75
10.3” x 7.9” x 13.6” lb 17.6
FLUID OUTLET PRESSURE
B
A
340 (cfm) 0,53 A (19)
N° 1 packing cf 0.5
AIR CONSUMPTION
B
8 (116)
255
7.9” x 6.3” x 10” lb 26.5
FLUID OUTLET PRESSURE
8 bar (116 psi)
170
bar (psi)
m3/min
cycles/min 85
FLUID OUTLET PRESSURE
A
FLUID OUTLET PRESSURE
C
A
bar (psi)
AIR CONSUMPTION
PUMP AIR FEEDING PRESSURE
14” x 7.8” x 16.5” N° 1 packing cf 0.9
AIR CONSUMPTION
Overall dimensions (A x B x C) 8.6” x 7” x 12.8” 8.6” x 7” x 12.8” 11.8” x 7.9” x 17.9” Packing - Weight N° 1 packing cf 0.9 lb 26 N° 1 packing cf 0.5 lb 15.4 N° 1 packing cf 0.5 lb 15.4 ** Different kind of muffler are available on request for special use or hard work * Displacement per cycle may be influenced by suction lift, fluid viscosity, air pressure, number of cycles per minute
IDEAL FOR ANY
INDUSTRY
GLASS INDUSTRY
PETROCHEMISTRY
CHEMICAL INDUSTRY
MINING AND BUILDING CONSTRUCTIONS PHARMACEUTICS INDUSTRY
SHIPYARD SEMICONDUCTOR INDUSTRY PAINT INDUSTRY
MOTOR INDUSTRY PAPER MILL TEXTILE INDUSTRY
PRINT INDUSTRY
CERAMIC INDUSTRY
FOOD INDUSTRY
ELECTRONIC INDUSTRY
RAASM USA, Inc. 1704 East Blvd, Suite 101 Charlotte, NC 28203 USA Phone +1 704 370 1906 Fax +1 704 373 2603 info@raasmusa.com www.raasmusa.com
All rights reserved to Raasm S.p.A.
WRUDA/D.P.2010-USA
Authorized distributor