INDECO 2014 EN A800

INDECO TECHNICAL CATALOGUE 2014 as at 1 January 2014

PN-EN 1527:2000

ITB AT-15-7902/2009

BUILDING RESEARCH INSTITUTE (ITB) PL 00-611 WARSAW, ul. FILTROWA 1 Member of Union Européenne pour L’Agrément Technique dans la construction - UEAtc Member of the European Organisation for Technical Approvals – EOTA Series:

TECHNICAL APPROVALS

ITB TECHNICAL APPROVAL AT-15-7902/2009 Pursuant to the Regulation of the Minister of Infrastructure of 8th November 2004 on technical approvals and bodies authorised to issue such approvals (Journal of Laws No 249, item 2497) and upon completion of an approval procedure carried out by the Building Research Institute in Warsaw acting upon request of: INDECO S.A. ul. Bukowiecka 92, 03-893 Warsaw the following products are declared suitable for use in the building industry: ®

INDECO Sliding, Folding and Pivoted Doors WR WKH H[WHQW DQG XQGHU WKH FRQGLWLRQV VSHFL¿HG LQ WKH $SSHQGL[ IRUPLQJ DQ LQWHJUDO SDUW RI WKLV ITB Technical Approval.

Expiry date: 30th January 2014

DIRECTOR Building Research Institute

Appendix: General and Technical Provisions Warsaw, 30th January 2009 ITB Technical Approval AT-15-7902/2009 is an amendment of Technical Approval AT-06-0482/2001 issued by COBR “Metalplast”. ITB Technical Approval AT-15-7902/2009 comprises 33 pages. The text of this document may be copied only in its entirety. Publication or dissemination of excerpts from the Technical Approval must be agreed in writing with the Building Research Institute.

Types of INDECO Door Systems

Bottom Roller Sliding Doors - Convenient access to the closet/wardrobe - A wide range of designs - Any front width, any number of door leaves - All leaves can be slid to one side in a multiple-track system

Bottom Roller Slant Sliding Doors - Full use of space in rooms with lowered, slant ceilings (attics, lofts) - Doors fitted to slant walls

Top Roller Sliding Doors - Suspended doors without the bottom track - Can also be used as pocket doors - Any front width, any number of door leaves - Excellent both for very wide and for very narrow doors - Can be easily trimmed at the bottom

2

Top and Bottom Roller Sliding Doors - The highest strength and durability - The door can be trimmed at the bottom - The door can be out-of-plumb - Special decorative effects can be obtained, such as inclined doors

Walk-through Sliding Doors without Thresholds - Full access to a walk-in closet - Can be used as pocket doors - No threshold

Pivoted Doors - Single and double, left-hand and right-hand doors - Access to the entire wardrobe content - A good solution for narrow doors

Folding Doors without Thresholds - Full access to the entire wardrobe content - Large wardrobe widths possible - Need half the space to open compared to pivoted doors with the same wardrobe width - No threshold

www.indeco.eu

INDECO A800 SERIES ALUMINIUM SYSTEM folding doors

Boundary conditions:

- maximum dimensions of the opening for the folding system: 3000 mm in height and 2000 mm in width (for double bi-fold doors).

- maximum dimensions of a bi-fold door: 3000 mm in height, 1000 mm in width (two leaves of 500 mmm each).

- maximum weight of 45 kg.

- panel thickness of 4 mm or 10 mm.

www.indeco.eu

INDECO A800 SERIES ALUMINIUM SYSTEM folding doors Basic Dimensions 35.8

35.8

41.5

‘

35.7

35.7

43.2

.2 ‘ 6

28.7

51.5

40.7

0

28.6

Q

P

0

80

3 . 5

36.5

0

P

‘

11.5

15.3

0

5.5

P

40.7

27.4

6.1

25.8

6/9.7 ‘

INDECO A800 SERIES ALUMINIUM SYSTEM folding doors Components 24 15/1 15/11 15/2 9

25

21 17

15/5 22 15/7

13

23

15/6

14

15/3

10

19 15/10

18

15/4 1

8

5 7

6 81

11

20

16

12

2-4 15/8 15/9

Rysunek złożeniowy 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 15/1 15/2

153152xx 153204xx 153205xx 153206xx 153352xx 153351xx 153353xx 156310xx 156200 16000101 156300xx 16000080 160000xx 895001xx 89500050ZL

Aluminium Rail, Wide Aluminium Stile Aluminium Stile Aluminium Stile Aluminium Connector Rail Narrow Aluminium Connector Rail 4 mm Aluminium Connector Rail 18 mm Decorative Strip Suspended Top Track Suspended Top Track End Cap Aluminium Decorative Profile Plug Gasket Hinge A800 Hardware Set - Top Pivot Socket - Top Pivot Pin Block

15/3 15/4 15/5 15/6 15/7 15/8 15/9 15/10 15/11 16 17 18 19 20 21 22 23 24 25

16000062A 156210xx 16000090 16000085 880000xx 16000005 810000xx 099249 099249A 156230AS 89500004

- Bottom Pivot Pin Block - Bottom Pivot Socket - Roller - Roller Mounting Block - Positioner - Locating Screw Block - Locator - 4.8 x 25 Self-tapping Screw - Toothed Spring Washer 4.8 x 25 Self-tapping Screw Suspended Top Track Fascia Self-adhesive Cap INDECO Self-adhesive Cap Protective Backing Double-sided Self-adhesive Tape Buffer Strip Buffer Strip Clip Buffer Strip Clip Suspended Track Holder Facia Suspended Track Holder

INDECO A800 SERIES ALUMINIUM SYSTEM folding doors Fabrication Instructions 1

Calculate door front dimensions > see page 5

2

Define the number of door leaves Define the number of single door leaves fixed to one top track. n – number of leaves

3

profile Calculate door leaf dimensions Door leaf width: n = 2 (2 leaves) DW = (OW – 10) / 2 n = 3 (3 leaves) DW = (OW – 10) / 3 n = 4 (4 leaves) DW = (OW – 10) / 4 Door leaf height: DH = OH – 65 mm

Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW – 45 mm mirror: PW = DW – 49 mm Panel length: board: PL = DH – 89 mm mirror: PL = DH – 93 mm Rail length: RL = DW – 61 mm Stile length: SL = DH

4

profile Calculate door leaf dimensions Door leaf width: n = 2 (2 leaves) DW = (OW – 10) / 2 n = 3 (3 leaves) DW = (OW – 10) / 3 n = 4 (4 leaves) DW = (OW – 10) / 4 Door leaf height: DH = OH – 65 mm

Cut components Based on door leaf dimensions, cut the components to the following dimensions: Panel width: board: PW = DW – 34 mm mirror: PW = DW – 38 mm Panel length: board: PL = DH – 89 mm mirror: PL = DH – 93 mm Rail length: RL = DW – 50 mm Stile length: SL = DH

82

Advice: For combination panels (board/board or board/mirror), make calculations in accordance with the “Combination panels” section in system A100.

5

Combination panels > see page 27

6

Mirror protection > see page 6

7

Drill installation holes > see page 76

8

Install connector rails > see page 28

9

Install stiles > see page 28

10 Install rails > see page 67 11 Structural reinforcement > see page 29

DW

www.indeco.eu

PW

PL

SL

3 4

DH

2

RL

INDECO A800 SERIES ALUMINIUM SYSTEM folding doors

Fabrication Instructions 12 Connect the leaves Insert the caps and lay both leaves next to each other with the back facing upwards, so that the caps abut. Use a power screwdriver to fix the hinges 895001xx to both leaves, providing for a distance of about 130 mm from the stile ends. Two hinges can be used for door heights of less than 1600 mm. To fix the hinges, use 3.9 x 16 self-tapping screws 87000055.

Advice: Make sure that the door leaves abut tightly when fixing the hinges. This will guarantee smooth operation of the door.

12

INDECO A800 SERIES ALUMINIUM SYSTEM folding doors

Installation Instructions 1

Cut the top track > see page 68

2

Install the top track Before fixing the top track, insert the top pivot socket, the roller and the positioner into the track. Fix the top track with screws, offsetting its face by: x = 9 mm profiles

83

Advice: Avoid applying excessive force when tightening screws to prevent track deformation. Use cheese-head screws for best result. The surface to which the track is fixed must not be curved.

Note: Before inserting the rollers, clean the inside of the suspended top track of any dirt that might accumulate during its installation.

3

Install the bottom pivot socket Determine a plane running vertically along the centre of the top track (e.g. using a plumb line). Position the bottom pivot socket at a distance of “y” mm from the side wall of the recess (the dimension allows for 5 mm buffer strip thickness). y = 39 mm – y = 45 mm –

profile profile

Advice: When fixing the hinge, set the screws at the centres of the oblong holes, which will enable you to adjust the position in both directions.

2

3

9

4

Y

INDECO A800 SERIES ALUMINIUM SYSTEM folding doors

Installation Instructions 4

Set the door in place Fold the door and set it in place so that the bottom pivot pin 15/3 sits in the socket 15/4 (see the assembly drawing). Screw the top roller 15/5 bolt into the mounting block 15/6 using a 7 mm open-ended spanner. Using a 13 mm open-ended spanner, unscrew the pivot pin of top pivot pin block 15/2 into the socket 15/1. Move the locating screw block 15/8 to the stile and fasten the block. Determine the final door height and set it symmetrically in the opening. Use a level to plumb the door, repositioning the top pivot socket if necessary. Fasten the top pivot socket 15/1 and all lock-nuts.

Advice: Exercise special care when installing doors. This operation should be performed by two persons.

5

Adjust the door By turning the top and bottom pivot pins (right-left), adjust the door vertically so that it is about 3 mm away from the wall when closed (this space will be filled by the dust-stop brush strip). Fasten the top and bottom pivot sockets to keep them in place. Close the door and adjust the top roller axle so that the door weight is distributed evenly between the hinge and the roller. By turning the pivot pins, door-to-floor clearance can be adjusted between 7 and 17 mm.

6

Fix the locator Close the door when adjusted. Align the locator 15/9 with the locating screw. Mark the position of the locator and open the door. Fix the locator to the floor with screws.

Note: The locator ensures stable position of the door when closed.

84

7

Fix the caps > see page 32

8

Fix buffer strips > see page 77

9

Fix the buffer strip clip > see page 10

10 Fix the positioner > see page 69 11 Fix the suspended top track fascia > see page 70 12 Fix the suspended top track fascia > see page 70

4

www.indeco.eu

5

6

INDECO A800 SERIES ALUMINIUM SYSTEM folding doors

System Components 1 153152xx > see page 37 Wide Aluminium Rail.

15 89500050ZL

2 153204xx > see page 37 Aluminium Stile.

3 153205xx > see page 37 Aluminium Stile.

4 153206xx > see page 37 Aluminium Stile.

5 153352xx > see page 38 Aluminium Connector Rail.

A800 Hardware Set A hardware set for A800 aluminium folding door systems. Twin-bearing rollers.

Accessories: 13 mm spanner 89500091, 6/10 mm spanner 89500093 Packaging: 1 set Weight: ~0.24 kg/set Availability: continuous

6 153351xx > see page 38 Aluminium Connector Rail.

7 153353xx > see page 38 4 mm Aluminium Connector Rail.

8 156310xx > see page 38 18 mm Decorative Strip.

9 156200 > see page 71 Aluminium Suspended Top Track.

10 16000101 > see page 71 Suspended Top Track End Cap. 11 156300xx > see page 38 Aluminium Decorative Profile.

12 16000080 > see page 38 Transparent Plug for Aluminium Profiles.

16 16000062A > see page 39 4.8 x 25 Allen-head Self-tapping Screw.

17 156210xx > see page 71 Aluminium Suspended Top Track Fascia.

13 160000xx > see page 39 Gasket.

18

14 895001xx

19 880000xx > see page 40 Self-adhesive Safety Backing.

16000090 > see page 40 16000085 Self-adhesive Cap.

20 16000005 > see page 41 Double-sided Self-adhesive Tape, 0.8 mm.

21 810000xx > see page 39 Self-adhesive Buffer Strip.

Self-aligning hinge for A800 aluminium system Colours: xx: SR-Silver, SA-Satin Packaging: 1 pce Weight: ~0.07 kg/pce Availability: continuous

22 099249 > see page 41 Buffer Strip Clip.

23 099249A > see page 41 Buffer Strip Clip.

24 156230AS > see page 71 Suspended Top Track Holder Fascia.

25 89500004 > see page 71 Suspended Top Track Holder.

www.indeco.eu

85

INDECO Aluminium profiles

Material

INDECO aluminium profiles are extruded from refined aluminium. This ensures excellent physical properties of profiles – better rigidity and strength.

Printed simulated wood decorative film Decorative film adhesive layer Satin anodized layer Anodized layer Conversion layer Aluminium Conversion layer Anodized layer

Properties

Properties that ensure corrosion resistance and colour fastness over the useful life of the product.

- Corrosion protection – anodized layer.

- Resistance to UV radiation.

Surface finish

90

The profiles have a coloured anodized surface. The anodizing process hardens the profile surface, which makes INDECO aluminium profiles highly resistant to mechanical damage. Four surface finish techniques are offered: 1. Anodizing. Formation of an oxide protective layer by galvanizing. A double satin finish provides attractive appearance.

2. Brushed anodizing. Surface brushing followed by anodizing, which produces a special decorative effect by adding a “third dimension” to the surface.

3. Laminating. Simulated wood finish is obtained by applying high-impact decorative film hot-applied with the use of thermosetting polymer adhesive.

4. Painting. A special technique of stoving paint powder coating produces the highest quality simulated wood finish.

Colours, colour abbreviations The following colours / finish types are available on standing offer:

Anodized, double satin: AS - Natural Anodized ASZ - Champagne

Brushed anode: ASSZ – Natural Anodized ASZSZ – Champagne

AO -Olive AZ - Gold

Simulated wood paint: DB – White SRP - Polished Silver SRM - Metallic Silver GRP - Polished Graphite

Any other colour/pattern is available to order.

Compliance: The anodized coat is anodized to Grade 15 in accordance with EN 12373-1:2001 and has a minimum average thickness of 15 μm.

www.indeco.eu

Aluminium Profile Colour Range

AS Natural Anodized AZ Gold ASZ Champagne AO Olive ASSZ Brushed Anodized ASZSZ Brushed Champagne

Note: The profile lengths stated in the catalogue represent usable lengths.

In fact, the profiles are 10 cm longer for manufacturing reasons.

DB White SRP Polished Silver SRM Silver metallic GRP Polished Graphite XX any colour/pattern available to order

www.indeco.eu

91

Indeco S.A. ul. Kaczorowa 37, 03-046 Warsaw, tel. (0-22) 313 0 313, fax (0-22) 313 0 314 www.indeco.eu e-mail: info@indeco.pl Helpline 022 313 0 313 (Mon-Fri 8:00-17:00)

www.indeco.eu