Issuu on Google+

Contents 1x Assembled Multi-stand bottom 1x Assembled Multi-stand top 3x Marquee signs 3x Panel stickers 4x Plastic label holders 4x Fixing bolts 6x Screws 1x Subwoofer (QB69) plate 2x 6� ONLY baffle boards

Multi-stand

Dealer Display Unit


Multi-stand - Dealer Display Unit Stand Assembly 1.

• Turn the top half of the cabinet upside down. • Fix the stand support brackets to the inside of the top half of the cabinet using 2x screws on each side. • Place the top half of the cabinet on top of the base.

X

2. • Insert 4x retaining bolts to secure the two parts of the stand.


Multi-stand - Dealer Display Unit

3. • Connect the two parts of the speaker connector, ensuring that the correct polarity is observed.

4. • To make the baffles for the speaker, cut the vinyl material with a sharp craft knife. • The baffles have been pre-routered with the speaker locations. These locations can be felt with your finger by pressing on the vinyl. • The speaker locations that will need to be removed is dependant on your speaker configuration. Please see configuration guide for more information.


Multi-stand - Dealer Display Unit Suggested Brand Layouts The stand can be customised in a variety of different ways. Detailed below are some standard layouts for VIBE, FLI and EDGE stands.

4”

1”

4”

5”

5” 1”

5”

6”

6”

6”

6x9”

6x9”

6x9”

1”

1”

5” 1”

5” 1”

6”

6” 1” 1”

4” (1”) 5” (*1”) 6” 6x9” *Tweeter hole required for FLI Comps


Multi-stand - Dealer Display Unit Power Supply Insert the power supply (supplied separately) into the lower part of the stand as shown in the diagram. Connect the red wires in the lower compartment to the positive terminal of the power supply and the black wires to the negative terminal.

Head Unit Insert fitting cage into the compartment shown in the diagram. Conenct the ISO block to the wiring harness of the head unit. Connect the RCA leads to the low-level output of the head unit.

Speakers Each speaker compartment is pre-wired for easy installation of the speakers. Connect the (solid/striped) wire to the positive speaker terminal. Connect the (solid) wire to the negative speaker terminal.

Switches Each speaker pair is connected to a single switch, as shown in the diagram. These can be used to turn the speakers on and off. DO NOT SWITCH ON MORE THAN ONE SET OF SPEAKERS AT ANY ONE TIME AS THIS MAY CAUSE DAMAGE TO THE AMPLIFIER

I O


Multi-stand - Dealer Display Unit Amplifier Mounting In addition to the board mounted amplifier, two amplifiers can be mounted to the bars between the speaker enclosures. • Retract the screws on the support bars. • Position the support bars in-line with the amplifier mounting holes. • Tighten the screws into the amplifier mounting holes.

Amplifier Wiring The lower, board mounted, amplifier is used to drive the speakers and a subwoofer (if required). Typically this will be a four channel amplifier. • Connect RCA inputs from the head unit. • Connect positive power, ground and remote cables. • Connect speaker cables. Refer to the amplifier manual for wiring configurations.

Illuminated Header The stand is equipped with an illuminated header sign. The required header sign can be slid into position and is held at the sides with the wooden batons.


Multi-stand - Dealer Display Unit Illuminated Header To power the lights in the header unit: • Connect the two parts of the power connector as detailed in the diagram ensuring that the correct polarity is observed. • Plug into a mains socket and power on.

Price Labels Price labels can be downloaded from www.midbass.com • Go to www.midbass.com • Register or login using your Midbass dealer login details • Click on ‘Useful Downloads’ • Download the relevant PDF document for your stand • Print onto A4 paper at 100% scale • Trim, price and fix the labels into position


Midbass Multi Stand Instructions