>> VM137 THERMOSTAT 5~30°C (41~86°F) Thermostat or controller for various applications, for regulation or Hi/Lo alarm. • temp. range: 5 to 30°C approx. (41 to 86°F) • output relay with LED-indicator • relay power rating: 3A normal open and normal closed contact • power supply: 12VDC / 100mA • hysteresis: 1°C ( 1.8°F) • dimensions: 54 x 62 x 28mm / 2.1 x 2.4 x 1.1"
Warmly recommended ! >> VM145 DIGITAL PANEL THERMOMETER WITH MIN/MAX READ-OUT
>> VM148 PANEL THERMOSTAT MODULE
Small multi-purpose LED digital panel thermometer, stores the lowest and highest measured temp until reset. (°C or °F) Wide power supply range: 9 to 24VDC or 7 to 17VAC. • power and temperature sensor connection via board-to-wire connector (20cm supplied) • temperature range: -30°C (-22°F) to + 120°C (248°F) • accuracy: - room temperature range: ± 1°C (2°F) - full range: ± 2°C ( +/- 4°F ) • distance between sensor and display unit: tested up to 10m (33ft) • current consumption: 40mA maximum • dimensions: - panel module: 67 x 40.5 mm / 2.6 x 1.6" - cut-out: 54 x 37 mm / 2.1 x 1.5" - sensor: 51 x 11 x 3 mm / 2 x 0.4 x 0.11" - mounting depth: 42mm / 1.65"
General purpose panel mount thermostat.Usable for heating or cooling purposes, (central heating, airco, incubator,… ). • temperature range: - °C: -18°C ~ + 60°C - °F: 0°F ~ +146°F • temperature resolution: ± 0.5°C or ± 2°F • accuracy: +/- 2°C, fine tune till +/- 0,5°C • readout update interval: 1 second • relay contact: NO - 3A (max. 230V) • power supply: 9 - 12V DC • power consumption: < 70mA • dimensions: - panel module: 67x40.5 mm / 2.6x1.6" - cut-out: 54x37 mm / 2.1x1.5" - mounting depth: 40mm / 1.6"
In-circuit programming connector
On-board PICKit2™ firmware port
External ICSP VDDCORE/VCAP selection for 28 pin 28 PIN PIC 16/18 series
Programming Busy 20 PIN PIC 16/18 series Output current selection 4 inputs for voltage sensing 5 to 24 Vdc
18 PIN PIC 16/18 series
4 outputs + 1 relay Direct LED drive or open collector selection
8 PIN PIC 10 series
14 PIN PIC 16 series 8 PIN PIC 18 series
>> VM142 MINI PIC(*)-PLC APPLICATION MODULE
>> VM203 USB PIC® PROGRAMMER
Create your own microcontroller project, without the need to develop hardware. This module has all you need. 4 inputs, 5 outputs, free to use LED and buzzer. • power supply: 12V DC (unregulated) / 100mA • 4 inputs (voltage sensing inputs) • input signal voltage: 5 - 24VDC, @ 4K7 • 4 NPN transistor outputs (open-collector, sink outputs).: - transistor output current: max. 100mA each - direct 12V relay drive possible (no need for protection diode) • 1 relay output with NO/NC contact (2A) • MCU speed: fixed 4MHz internal oscillator
This PICKit™2 Development Programmer is very versatile. It features on board sockets for many types of PIC® microcontrollers. Also provided is an ICSP connector, to program your onboard device. It is compatible with the free tools from Microchip such as the MPLAB® IDE environment. Check Microchip.com for PICKit™2 compatible devices. PICKit, PIC and MPLAB are trademarks or registered trademarks of Microchip Technology Inc. • USB powered • power output to target is supported • indicator LEDs for power supply and programming mode • USB driven alternative for K8048