Page 1

UPONOR INFRASTRUCTURE Technical literature

461


13. Technical literature A list of the publications referred to in the Uponor Technical Manual, and of other relevant publications, is presented below. • Uponor, Kunnallistekniset putkistot, Asentajan käsikirja (Uponor, Municipal Pipe Systems, Installer’s Manual) (In Finnish). • Uponor, Kunnallistekniset putkistot, Suunnittelijan käsikirja (Uponor, Municipal Pipe Systems, Designer’s Manual) (In Finnish). • RIL 77 Thermoplastic pipes installed underground or under water. Laying instructions. Association of Finnish Civil Engineers RIL ry, 2005 • SFS Handbook 102, Plastic pipes. Finnish Standards Association SFS, 2nd Revised Edition, 2005 • Kunnallisteknisten töiden yleinen työselostus 02, KT02, Suomen Kuntaliitto, 2002 (General Work Description for Public Utility Construction 02, KT02. Association of Finnish Local and Regional Authorities, 2002) (in Finnish)

462

• Muoviputkijärjestelmät, Muoviteollisuus Ry, 2003 (Plastic Piping and Ducting Systems, Finnish Plastics Industries Federation 2003) (in Finnish) • Viherrakentajan käsikirja, Timo Soini, 2005 (A Landscaper's Handbook, Timo Soini, 2005) (in Finnish) • Rakennuspohjan ja piha-alueiden maarakenne- ja kuivatusopas, MaKu 2001 (A Guide to Soil Structure and Drainage for Building Foundations and Green Areas, MaKu 2001. Finnish Ministry of the Environment, Finnish Association of Consulting Firms SKOL, Finnish Geotechnical Society, Innogeo Oy 2000) (in Finnish) • Tien kuivatustarvikkeet, Suunnitteluja valintaperusteita, (Road Drainage Equipment, Design and Selection Criteria, Finnish Road Administration 1993) (in Finnish)

Technical Literature


14. Standards Product standards for building sewerage systems EN 1329-1:2000)

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Unplasticised polyvinyl chloride (PVC-U). Part 1: Specifications for pipes, fittings and the system.

ENV 1329-2:2001

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Unplasticised polyvinyl chloride (PVC-U). Part 2: Guidance for the assessment of conformity

EN 1451-1:2000)

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polypropylene (PP). Part 1: Specifications for pipes, fittings and the system.

ENV 1451-2:2001

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polypropylene (PP). Part 2: Guidance for the assessment of conformity

Product standards for land drainage systems EN 1451-1:2000)

Plastic piping systems for non-pressure underground drainage and sewerage. Unplasticised polyvinyl chloride (PVC-U). Part 1: Specifications for pipes, fittings and the system.

ENV 1401-2:2000

Plastic piping systems for non-pressure underground drainage and sewerage. Unplasticised polyvinyl chloride (PVC-U). Part 2: Guidance for the assessment of conformity

ENV 1401-3:2001

Plastic piping systems for non-pressure underground drainage and sewerage. Unplasticised polyvinyl chloride (PVC-U). Part 3: Guidance for installation

EN 1456-1:2001

Plastics piping systems for buried and above-ground drainage and sewerage under pressure. Unplasticised polyvinyl chloride (PVC-U). Unplasticised polyvinyl chloride (PVC-U). Part 1: Specifications for piping components and the system

CEN/TS 1456-2:2003

Plastics piping systems for buried and above-ground drainage and sewerage under pressure. Unplasticised polyvinyl chloride (PVC-U). Unplasticised polyvinyl chloride (PVC-U). Part 2: Guidance for the assessment of conformity

EN 1852-1:1997

Plastic piping systems for non-pressure underground drainage and

+ EN 1852-1/A1:2002

sewerage. Polypropylene (PP). Part 1: Specifications for pipes, fittings and the system.

standards

463


ENV 1852-2:2000

Plastic piping systems for non-pressure underground drainage and sewerage. Polypropylene (PP). Part 2: Guidance for the assessment of conformity

CEN/TS 1852-3:2003

Plastics piping systems for non-pressure underground drainage and

+ CEN/TS 1852-3/A1:2005

sewerage. Polypropylene (PP) Part 3: Guidance for installation

EN 12666-1:2006

Plastics piping systems for non-pressure underground drainage and sewerage. Polyethylene (PE) Part 1: Specifications for pipes, fittings and the system

CEN/TS 12666-2:2006

Plastics piping systems for non-pressure underground drainage and sewerage. Polyethylene (PE) Part 2: Guidance for the assessment of conformity

EN 13244-1:2003

Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) Part 1: General

EN 13244-2:2003

Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) Part 2: Pipes

EN 13244-3:2003

Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) Part 3: Fittings

EN 13244-4:2003

Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) Part 4: Valves

EN 13244-5:2003

Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) Part 5: Fitness for purpose of the system

CEN/TS 1852-3:2003

Plastic piping systems for non-pressure underground drainage and

+ CEN/TS 1852-3/A1:2005

sewerage. Polypropylene (PP). Part 3: Guidance for installation

EN 12666-1:2006

Plastics piping systems for non-pressure underground drainage and sewerage. Polyethylene (PE). Polyethylene (PE). Part 2: Guidance for the assessment of conformity.

EN 13244-1:2003

Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage. Polyethylene (PE). Polyethylene (PE). Part 1: General

EN 13244-2:2003

Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage. Polyethylene (PE). Polyethylene (PE). Part 2: Pipes

EN 13244-3:2003

Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage. Polyethylene (PE). Polyethylene (PE). Part 3: Fittings

464

standards


EN 13244-4:2003

Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage. Polyethylene (PE). Part 4: Valves

EN 13244-5:2003

Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage. Polyethylene (PE). Part 5: Fitness for purpose of the system

CEN/TS 13244-7:2003

Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage. Polyethylene (PE). Part 7: Guidance for the assessment of conformity

EN 13476-1:2007

Plastics piping systems for non-pressure underground drainage and sewerage. Structured-wall piping systems of unplasticised poly (vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE). Polyethylene (PE). Part 1: General requirements and performance characteristics

EN 13476-2:2007

Plastics piping systems for non-pressure underground drainage and sewerage. Structured-wall piping systems of unplasticised poly (vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE). Polypropylene (PP). Polyethylene (PE). Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system, Type A

EN 13476-3:2007

Plastics piping systems for non-pressure underground drainage and sewerage. Structured-wall piping systems of unplasticised poly (vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE). Polypropylene (PP). Part 3: Specifications for pipes and fittings with smooth internal and profiled external surface and the system, Type B

EN 13566-1:2003

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks. Part 1: General

EN 13566-2:2006

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks. Part 2: Lining with continuous pipes

EN 13566-3:2003

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks. Part 3: Lining with close-fit pipes

EN 14758-1:2006

Plastics piping systems for non-pressure underground drainage and sewerage. Polypropylene with mineral modifiers (PP-MD). Part 1: Specifications for pipes, fittings and the system

prCEN/TS 14758-2

Plastics piping systems for non-pressure underground drainage and sewerage. Polypropylene with mineral modifier(s) (PP-MD). Part 2: Guidance for the assessment of conformity.

CEN/TS 14758-3:2006

Plastics piping systems for non-pressure underground drainage and sewerage. Polypropylene with mineral modifier(s) (PP-MD). Part 3: Guidance for installation Plastics piping systems for buried and above-ground pressure systems for water for general purposes. Drainage and sewerage - Polyethylene (PE) Part 3: Lining with close-fit pipes

standards

465


EN 14758-1:2006

Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD). Part 1: Specifications for pipes, fittings and the system

prCEN/TS 14758-2

Plastics piping systems for non-pressure underground drainage and sewerage. Polypropylene with mineral modifier(s) (PP-MD). Part 2: Guidance for the assessment of conformity.

CEN/TS 14758-3:2006

Plastics piping systems for non-pressure underground drainage and sewerage. Polypropylene with mineral modifier(s) (PP-MD). Part 3: Guidance for installation

Product standards for household water systems EN 1452-1:2000

Plastics piping systems for water supply. Unplasticised polyvinyl chloride (PVC-U). Part 1: General

EN 1452-2:2000

Plastics piping systems for water supply. Unplasticised polyvinyl chloride (PVC-U). Part 2: Pipes

EN 1452-3:2000

Plastics piping systems for water supply. Unplasticised polyvinyl chloride (PVC-U). Part 3: Fittings

EN 1452-4:2000

Plastics piping systems for water supply. Unplasticised polyvinyl chloride (PVC-U). Part 4: Valves and ancillary equipment

EN 1452-5:2000

Plastics piping systems for water supply. Unplasticised polyvinyl chloride (PVC-U). Part 5: Fitness for purpose of the system.

ENV 1452-6:2002

Plastics piping systems for water supply. Unplasticised polyvinyl chloride (PVC-U). Part 6: Guidance for installation

ENV 1452-7:2001

Plastics piping systems for water supply. Unplasticised polyvinyl chloride (PVC-U). Part 7: Guidance for the assessment of conformity

EN 12201-1:2003

Plastic piping systems for water supply. Polyethylene (PE). Part 1: General

EN 12201-2:2003

Plastic piping systems for water supply. Polyethylene (PE). Part 2: Pipes

EN 12201-3:2003

Plastic piping systems for water supply. Polyethylene (PE). Part 3: Fittings

EN 12201-4:2003

Plastics piping systems for water supply. Polyethylene (PE). Part 4: Valves

EN 12201-5:2003

Plastic piping systems for water supply. Polyethylene (PE). Part 5: Fitness for purpose of the system.

CEN/TS 12201-7:2003

Plastics piping systems for water supply. Polyethylene (PE). Part 7: Guidance for the assessment of conformity

466

standards


Product standards for land drainage systems DS 2077.1:1983

Plastic pipes. - Drain pipes and fittings - Requirements

DS 2077.2:1983

Plastic pipes. - Drain pipes and fittings - Testing and inspections

SFS 5211

Plastic pipes. PVC field drainage drainage systems.

SFS 5675

Plastic pipes. Double-wall pipe drainage pipes and pipe fittings.

Product standards for cable ducting systems EN 50086-2-4:1995

Conduit systems for electrical installations. Part 2−4: Particular requirements for conduit systems buried underground.

Testing and other standards EN ISO 527-1:1996

Plastics. Determination of tensile properties. Part 1: General principles

EN ISO 527-2:1996

Plastics. Determination of tensile properties. Part 2: Test conditions for moulding and extrusion plastics.

EN 681-1:1996

Elastomeric seals. Materials requirements for pipe joint seals used in

+ EN 681-1/A1:1998

water and drainage applications.

+ EN 681-1/AC:2002

Part 1: Vulcanised rubber

+ 681-1/A2:2003 + EN 681-1/A3:2005 EN 681-2:2000

Elastomeric seals. Material requirements for pipe joint seals used in

+ EN 681-2/A1:2003

water and drainage applications.

+ 681-2/A2:2005

Part 2: Thermoplastic elastomers

EN 681-3:2000

Elastomeric seals. Material requirements for pipe joint seals used in

+ EN 681-3/A1:2003

water and drainage applications.

+ 681-3/A2:2005

Part 3: Cellular materials of vulcanised rubber

EN 681-4:2000

Elastomeric seals. Material requirements for pipe joint seals used in

+ EN 681-4/A1:2003

water and drainage applications.

+ 681-4/A2:2005

Part 4: Cast polyurethane sealing elements

EN 728:1997

Plastics piping and ducting systems. Polyolefin pipes and fittings. Determination of oxidation induction time.

DS 735:1982

Colours for identification purposes

EN 744:1995

Plastics piping and ducting systems. Thermoplastics pipes. Test method for resistance to external blows using the round-the-clock method.

EN ISO 1133:2005

Determination of the melt mass-flow rate (MFR) and the melt volumeflow rate (MVR) of thermoplastics.

EN ISO 1183-1:2004

Plastics. Methods for determining the density of non-cellular plastics. Immersion method, liquid pyknometer method and titration method.

EN ISO 1183-2:2004

Plastics. Methods for determining the density of non-cellular plastics. Part 2: Density gradient column method.

standards

467


EN ISO 1183-3:1999

Plastics. Methods for determining the density of non-cellular plastics. Part 3: Gas pyknometer method.

EN 1277:2004

Plastics piping systems - Thermoplastics piping systems for buried nonpressure applications - Test methods for leaktightness of elastomeric sealing ring type joints.

EN 1411:1996

Plastics piping and ducting systems. Thermoplastics pipes. Determination of resistance to external blows by the staircase method.

EN 1437:2002

Plastics piping systems. Piping systems for underground drainage and sewerage. Test method for resistance to combined temperature cycling and external loading.

DIN 2501-1

Flanges; Connecting Dimensions

SFS 3115:en

Plastic pipes. Tightness test for pressure pipes.

(SFS 3115:E:1976) ISO 7005-1:1992

Metallic flanges. Part 1: Steel flanges

EN ISO 9001:2000

Quality management systems - Requirements

EN ISO 9080:2003

Plastics piping and ducting systems. Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation.

EN ISO 9969:1995

Thermoplastics pipes. Determination of ring stiffness.

EN ISO 14001:2004

Environmental management systems — Requirements with guidance for use.

EN 14741:2006

Thermoplastics piping and ducting systems. Joints for buried nonpressure applications. Test method for the long-term sealing performance of joints with elastomeric seals by estimating the sealing pressure.

DIN 52612-1

Testing of Thermal Insulating Materials; Determination of Thermal Conductivity by the Guarded Hot Plate Apparatus; Test Procedure and Evaluation.

468

standards

Profile for Uponor Finland

13 14 technical literature and standards  

https://www.uponor.fi/-/media/country-specific/finland/download-centre/technical-handbook-eng/13-14_technical_literature_and_standards.pdf?v...

13 14 technical literature and standards  

https://www.uponor.fi/-/media/country-specific/finland/download-centre/technical-handbook-eng/13-14_technical_literature_and_standards.pdf?v...

Profile for uponorfi