Page 1

Uponor Smatrix Move PRO H E AT I N G / C O O L I N G A P P L I C AT I O N E N I N S TA L L AT I O N A N D O P E R AT I O N MANUAL

12 | 2016


UK

Table of contents

CZ DE

1 2

DK

Copyright and disclaimer......................................3

6

Preface...................................................................4

7 Operate the Uponor Smatrix Move PRO ­controller.............................................................51

2.1 2.2

EE

Safety instructions.....................................................4 Correct disposal of this product (Waste Electrical and Electronic Equipment)........................................4

Installation procedure..............................................12 Prepare for installation............................................12 Installation examples...............................................12

7.1 Principle of operation..............................................51 7.2 Controller layout......................................................51 7.3 Navigating the menu system...................................51 7.4 Start up...................................................................52 7.5 Information button..................................................52 7.6 Main menu..............................................................53 7.7 System Overview.....................................................53 7.8 Information..............................................................53 7.9 Alarms.....................................................................61 7.10 Settings...................................................................62 7.11 Pre Heating Info....................................................131 7.12 Pre Heating Settings.............................................133 7.13 Menu tree..............................................................140

5 Install Uponor Smatrix Move PRO ­controller.....23

8 Maintenance......................................................150

3

Uponor Smatrix Move PRO...................................5 3.1 System overview........................................................5 3.2 Example of a system..................................................6 3.3 Uponor Smatrix Move PRO components...................7 3.4 Accessories..............................................................10 3.5 Functions................................................................10

ES FI

4

Install Uponor Smatrix Move PRO system.........12 4.1 4.2 4.3

FR

5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8

HR HU IT

5.9 5.10

LT

5.11 5.12 5.13 5.14 5.15 5.16 5.17 5.18

LV NL

Finishing installation..........................................50

Placement of controller...........................................23 Select controller application....................................23 Attach stickers.........................................................23 Insert microSD card.................................................23 Attach controller to the wall....................................24 Terminal cover.........................................................24 Connect sensors to controller..................................24 Connect external signal for heating/cooling switch to the controller............................................36 Connect mixing valve actuators to the controller.....36 Connect diverting valve actuators to the controller.................................................................37 Connect circulation pumps to the controller............38 Connect a dehumidifier to the controller.................39 Connect Uponor Smatrix Base PRO controller.........40 Connect Modbus RTU interface...............................40 Connect the controller to AC power.........................41 Alternate power inputs............................................41 Startup wizard.........................................................41 Pre heating concrete slab (DIN 1264-4)..................48

8.1 8.2 8.3 8.4

Manual preventive maintenance............................150 Automatic preventive maintenance.......................150 Corrective maintenance.........................................150 Controller display...................................................150

9 Troubleshooting................................................151 9.1 9.2 9.3

Troubleshooting after installation..........................152 Contact the installer..............................................152 Installer instructions..............................................152

10 Technical data....................................................153 10.1 10.2 10.3 10.4

Technical data........................................................153 Technical specifications.........................................154 Controller layout....................................................154 Wiring diagram, Uponor Smatrix Move PRO controller...............................................................155 10.5 Dimensions............................................................156

11 Installation report.............................................157

NO PL PT RO RU SE SK 2

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK

1

Copyright and disclaimer

CZ DE

Uponor has prepared this installation and operation manual and all the content included solely for information purposes. The contents of the manual (including graphics, logos, icons, text, and images) are copyrighted and protected by worldwide copyright laws and treaty provisions. You agree to comply with all copyright laws worldwide in your use of the manual. Modification or use of any of the contents of the manual for any other purpose is a violation of Uponor’s copyright, trademark and other proprietary rights. The presumption for the manual is that the safety measures have been fully complied with and, further, that Uponor Smatrix Move PRO, including any components that are part of such system, covered by the manual: • is selected, planned and installed and put into operation by a licensed and competent planner and installer in compliance with current (at the time of installation) installation instructions provided by Uponor as well as in compliance with all applicable building and plumbing codes and other requirements and guidelines; • has not been (temporarily or continuously) exposed to temperatures, pressure and/or voltages that exceed the limits printed on the products or stated in any instructions supplied by Uponor; • remain in its originally installed location and is not repaired, replaced or interfered with, without prior written consent of Uponor;

While Uponor has made efforts to ensure that the manual is accurate, Uponor does not guarantee or warrant the accuracy of the information contained herein. Uponor reserves the right to modify the specifications and features described herein, or discontinue manufacture of Uponor Smatrix Move PRO described at any time without prior notice or obligation. The manual is provided “as is” without warranties of any kind, either expressed or implied. The information should be independently verified before using it in any manner.

DK EE ES FI

To the fullest extent permissible, Uponor disclaims all warranties, expressed or implied, including, but not limited to, the implied warranties of merchantability, fitness for particular purpose and non-infringement.

FR HR

This disclaimer applies to, but is not limited to, the accuracy, reliability or correctness of the manual. Under no circumstances shall Uponor be liable for any indirect, special, incidental or consequential damages or loss that result from the use of or the inability to use the materials or information in the manual, or any claim attributable to errors, omission or other inaccuracies in the manual, even if Uponor has been advised of the possibility of such damages.

HU IT LT

This disclaimer and any provisions in the manual do not limit any statutory rights of consumers.

LV

• is connected to potable water supplies or compatible plumbing, heating and/or cooling products approved or specified by Uponor;

NL

• is not connected to or used with non-Uponor products, parts or components except for those approved or specified by Uponor; and

NO PL

• does not show evidence of tampering, mishandling, insufficient maintenance, improper storage, neglect or accidental damage before installation and being put into operation.

PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

3


UK

2

CZ

Preface

DE This installation and operation manual describes how to install and operate the components of the system.

DK

2.1 Safety instructions EE

Warnings used in this manual

ES

The following symbols are used in the manual to indicate special precautions when installing and operating any Uponor equipment:

W arning !

FI

Risk of injury. Ignoring warnings can cause injury or damage components.

FR

C aution ! Ignoring cautions can cause malfunctions.

HR

Safety measures Conform to the following measures when installing and operating any Uponor equipment:

HU

• Read and follow the instructions in the installation and operation manual.

IT

• Installation must be performed by a competent person in accordance with local regulations.

LT

2.2 Correct disposal of this product (Waste Electrical and Electronic Equipment) N OT E ! Applicable in the European Union and other European countries with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed with other household wasted at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes of disposal.

• It is prohibited to make changes or modifications not specified in this manual. • All power supplies must be switched off before starting any wiring work.

LV

• Do not use water to clean Uponor components.

NL

• Do not expose the Uponor components to flammable vapours or gases. Uponor cannot accept any responsibility for damage or breakdown that can result from ignoring these instructions.

NO PL

Power

W arning !

PT

The Uponor system uses 50 Hz, 230 V AC power. In case of emergency, immediately disconnect the power.

RO

Technical constraints

RU

C aution ! To avoid interference, keep installation/data cables away from power cables of more than 50 V.

SE SK 4

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK

3

Uponor Smatrix Move PRO

CZ DE

Uponor Smatrix Move PRO is a supply temperature control system for use in different zones. The number of zones and setup vary depending on which application package (supplied with the controller) has been installed (inserting the microSD card into the controller). This manual only reflects the installation of the controller together with the heating/cooling application package. Heating application Using the heating application, enables up to four zones to be setup for heating with different radiant systems (such as underfloor loops, radiators etc.), domestic hot water, or snow melting (keeping large areas clear of snow). Heating/cooling application Using the heating/cooling application enables up to three zones to be setup for heating and/or cooling with different radiant systems (such as underfloor loops, ceiling panels etc.), domestic hot water, or snow melting (keeping large areas clear of snow)

3.1 System overview Uponor Smatrix Move PRO consists of a controller and a wide array of sensors. Together they control the supply temperature in each zone by managing the connected valve actuators and circulation pumps. The zones can be setup as follows. Zone

Setup alternatives

1

Stand Alone Control

Stand Alone Control If the zone is setup as Stand Alone Control, the controller operates without individual room control. The supply temperature setpoint is calculated using an outdoor sensor and a room temperature sensor (optional for heating only, mandatory together with humidity sensor S-157 for heating/cooling).

DK

The zone can switch between heating and cooling using one of the following functions (set in the startup wizard):

ES

EE

FI

• Indoor and Outdoor uses the indoor and outdoor temperatures to switch the zones between heating and cooling.

FR

• Supply Water Temp. uses the supply water temperature to switch the zones between heating and cooling.

HR

• Contact Input uses an external signal to switch the zones between heating and cooling.

HU

• Force Heating sets the zones in forced heating. • Force Cooling sets the zone in forced cooling.

IT

The optional room temperature sensor is placed in a reference area and enables an indoor temperature setpoint parameter. It is used to keep the indoor temperature as close as possible to the indoor temperature setpoint.

LT LV

A relative humidity sensor is used to avoid condensation problems while in cooling mode. An optional condesation sensor can be installed for added security.

NL

Smatrix Base PRO

2

NO

Stand Alone Control Smatrix Base PRO

PL

Domestic Hot Water

3

Stand Alone Control Smatrix Base PRO

PT

Meltaway

RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

5


UK CZ DE DK

Smatrix Base PRO

Meltaway

If the zone is setup as Smatrix Base PRO, individual room control in the zone is enabled via an integrated Uponor Smatrix Base PRO system. The supply temperature setpoint is calculated using sensor data and current mode from the Base PRO system.

If the zone is setup as Meltaway, snow melting (keeping large areas clear of snow) is enabled in the zone. The supply temperature setpoint is calculated using an outdoor sensor, a ground temperature sensor, and a ground moisture sensor.

Heating/cooling mode is set from the Smatrix Base PRO system.

When to start or stop snow melting (status: Stop, Idle or Meltaway) is determined by using an outdoor temperature sensor and two Uponor Smatrix Move PRO Sensor Snow S-158 sensors. One of S-158 sensors is used for measuring the ground temperature and the other one is used for measuring the ground moisture level.

The outdoor temperature sensor is connected to the Base PRO system via a thermostat, registered as a system device. The thermostat is preferably placed in a non-public area such as a technical room. The outdoor temperature sensor data will also be used by the other zones.

EE ES

This requires the Move PRO controller to be connected to a Smatrix Base PRO bus.

FI

A relative humidity sensor within the Smatrix Base PRO system is used to avoid condensation problems while in cooling mode.

FR

Domestic Hot Water

HR

If the zone is setup as Domestic Hot Water, hot water regulation is enabled in the zone. The supply temperature setpoint is set in the Move PRO controller display.

HU

The return temperature sensor is used to calculate the difference between the supply and return temperature and tripps an alarm if the difference is too high. The primary return sensor is used to protect the heat source from too low return temperatures.

3.2 Example of a system The illustration below shows a property divided into different zones. All zones are controlled by the Uponor Smatrix Move PRO. N OT E ! This is an example. The Move PRO controller can be setup in a wide array of combinations.

N OT E ! If the zone is setup as Domesitc Hot Water without a return sensor, the zone will work with reduced functionality. Functions such as BoostPower and hot water recirculation requires a return sensor to work properly.

IT LT

1 3

LV

2

NL NO PL PT RO

Zone

Description

1

The zone (underfloor heating in a warehouse) is setup as Stand Alone Control.

2

The zone (domestic hot water production) is setup as Domestic Hot Water.

3

The zone (keeping a parking lot and a large court yard clear of snow) is setup as Meltaway.

RU SE SK 6

U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK

3.3 Uponor Smatrix Move PRO components C ontroller The controller operates the valve actuators and circulation pumps, which in turn affect the supply water temperature to the zone.

Components of the controller The illustration below shows the controller and its components with the heating/cooling application package.

CZ DE

The temperature in up to three zones can be regulated by the controller.

DK

Uponor Smatrix Move PRO Controller X-159 Main characteristics:

2 1 15VDC GND 12VDC IN GND 24VAC IN 1 2 3 4 5 6 7 8 9

10 11 12 13 14 15 16 17 18

- +

42 43

• Integrated display with menu system.

- +

- +

45 46

48 49

52 53 54 55 56

21 22 23 24 25 26

72 73

75 76

B

T

microSD

N L 125 mA 230 V ±10% 50/60 Hz

77 78

- A B

1 2

L N PRO PRO

L N

PRO PRO

3

L N

PRO PRO

06 | 2016

4

5

5

6

6

7

7

8

8

9

10 11 12 13 14 15 16 17 18 10 11 12 13 14 15 16 17 18

9

41

42

43

44

45

46

48

47

49

50

51

52

53

54

55

56

ES 56

1T

L

L

55

N

N

54 53

80

GND

52

GND

15VDC

230 V ± 10% 50/60 Hz

24VAC IN

12VDC IN

N L

3

IIN ≤ 6A

50

2

IIN ≤ 6A

!

77

N L

76

46

2

1

3

45

2

74

1

44

3

N L

1/2

73

3

43

2

30

Base PRO

26

3

29 28

25

3 1/2

27 26

3

25 24

1/2

8 8 7 7

T

4 3 3

1

2

microSD

2

27

28

71

72

73

74

75

76

77

78

79

80

125 mA

microSD

1

26

1

25

Base PRO

24

• Heating/cooling curve (Stand Alone Control and Smatrix Base PRO zones only).

Item A

Uponor Smatrix Move PRO Controller X-159

• Connection of maximum three actuators (one per zone).

B

Heating/cooling application package (microSD card, application diagram, connection stickers)

• Connection of maximum three circulation pumps (one per zone).

FI

23

3B A

22

Base PRO

-

L

21

N

9

N L

SMATRIX BASE PRO – BUS

≤ 1A

10 11 12 13 14 15 16 17 18 10 11 12 13 14 15 16 17 18

≤ 6A

N L

9

≤ 6A

N L

2

30

L

6

29

N

6

B 23

230 V ± 10% 50/60 Hz

5

A 22

2

5

21

26

3

4

microSD

25

2

!

Base PRO SMATRIX BASE PRO – BUS

1

!

3

!

41

71

42

72

1

1

75

47

48

3

49

78

IIN ≤ 1A

! !

1

51

Base PRO

79

15VDC

Base PRO

125 mA

2

3

4

GND

2

3

GND

1

2

24VAC IN

1

12VDC IN

• Control of supply temperature for up to three zones (up to three heating systems, one snow melting zone, and one domestic hot water zone).

EE

A

3

microSD

Description

FR HR

The box also contains a heating application package which is explained in another installation and operation manual.

HU

• Pump exercise. • Change supply temperature using customizable schedules (ECO mode).

IT

• Initial setup done via startup wizard. • BMS ready via Modbus and KNX interfaces.

LT

• Integration with Uponor Smatrix Base PRO via system bus.

LV

Options: • Cabinet or wall mounted using a DIN rail (not supplied).

NL NO PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

7


UK R oom

H umidity

sensor

N OT E ! The room sensor is affected by the temperature of the surrounding surfaces as well as the ambient air temperature.

CZ DE DK EE ES

Uponor Smatrix Move PRO Sensor Humidity S-157 The sensor is designed to measure the relative humidity within the zone.

Uponor Smatrix Move PRO Sensor Room S-155

The sensor is only used in zones setup as Stand Alone Control.

The sensor is designed to measure the indoor reference temperature within the zone.

Main characteristics:

The sensor is only used in zones setup as Stand Alone Control.

• Prepared for wall or connection box mounting.

• Sensor range is 0 – 100 %.

Main characteristics:

Components of the humidity sensor:

• Sensor range is 0 – 60 °C.

The illustration below shows the humidity sensor and its components.

• Prepared for wall or connection box mounting.

FI

sensor

Components of the room sensor: The illustration below shows the room sensor and its components.

FR

A HR

Item A

HU

Description Smatrix Move PRO Sensor Humidity S-157

A Item

IT

A

Description Smatrix Move PRO Sensor Room S-155

LT LV NL NO PL PT RO RU SE SK 8

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK C ondensation

S now

sensor

and ice sensor

Uponor Smatrix Condensation Set S-159

Uponor Smatrix Move PRO Sensor Snow S-158

CZ

The sensor set is designed to detect and prevent condensation while the zone is in cooling mode.

The sensor is designed to be embedded into outdoor surfaces to measure the ground temperature and moisture level.

DE

The sensor is only used in zones setup as Stand Alone Control or Smatrix Base PRO.

DK

• Sensor range: Condensation detected, Yes/No.

The sensor is only used in zones setup as Meltaway. To ensure the snow melting function, two Uponor Smatrix Move PRO Sensor Snow S-158 and three supply/return sensors must be installed.

• Converter for cooling allowed signal.

Main characteristics:

EE

Components of the condensation sensor:

• Detects moisture.

The illustration below shows the condensation sensor and its components.

• Detects temperature.

Main characteristics:

ES

• Horizontal installation to ensure collection of draining melt water.

FI

Options:

A Item

B

Description

A

Condensation sensor

B

Converter

• The sensor can be used as either ground temperature sensor or ground moisture sensor. It cannot be used for both at once.

FR HR

Components of the snow sensor: The illustration below shows the snow sensor and its components.

HU IT

A Item

B

LT

Description

A

Smatrix Move PRO Sensor Snow & Ice S-158

B

Mounting socket

LV NL NO PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

9


UK CZ

3.4 Accessories

3.5 Functions

Uponor offers a wide variety of accessories for use with the standard portfolio.

H eating / cooling

DE

A

DK

B

C

N OT E ! Some of these accessories may be included in the system.

EE ES

Item Component A

FI

Uponor Smatrix Sensor Outdoor S-1XX

Description Outdoor sensor for use with system without a zone setup as Smatrix Base PRO.

curve

The Move PRO controller use a heating/cooling curve to calculate the supply temperature setpoint. This requires the zone to be setup as Stand Alone Control or Smatrix Base PRO. The heating/cooling curve for the Uponor Smatrix Move PRO controller is shown in the diagram below. The diagram shows the calculated supply temperature, for each curve, at different outdoor temperatures. The controller uses the selected curve to operate the mixing valve, which in turn adjusts the supply temperature to the system. Supply temperature 5 4,5 4 3,5

80

3

2,5

2

70

(outdoor sensor S-1XX)

FR

B

HR

Uponor Smatrix Move Sensor Supply/Return S-152

C

Uponor Smatrix Bus cable A-145

1 0,8

50

0,7 0,6

40 0,4 30

0,2

20

(supply/return sensor S-152)

HU

1,2

60

Sensor that can be used as either a supply or return sensor.

1,5

10

Bus cable for use with integration of Uponor Smatrix Base PRO system

36 34 32 30 28 26 24 22 20 18 16 14 12 10 8

6

4

2

0 -2 -4 -6 -8 -10 -12 -14 -16 -18 -20

Outdoor temperature

IT

The choice of curve depends on a combination of different factors, such as how well insulated the house is, geographical location, type of heating/cooling system etc.

LT

Example: A poorly insulated house heated by a radiator system requires a higher curve value than an equivalent house with underfloor heating.

LV

The curves in the diagram are also limited by maximum and minimum parameters set in the system (marked in the diagram with extra thick lines).

NL NO PL PT RO RU SE SK 10

U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK R eal

S ystem

time clock

To facilitate accurate scheduling, the controller contains a real time clock. If an Uponor Smatrix Base PRO system is connected it will act as a time master, pushing the current time setting to the Move PRO controller.

C omfort

and

ECO

modes

( scheduling )

With the integrated timer in the controller, it is possible to change the temperature setpoint modes between two different temperatures. To utilise the Comfort and ECO modes in a zone, the zone must be setup as Stand Alone Control and using an room sensor. Available modes are Comfortand ECO (economy). See example of Comfort and ECO mode below. Schedule 1

integration with

B ase PRO

systems

The system can be integrated with an Uponor Smatrix Base PRO system to enable individual room control in the zone.

CZ

The outdoor temperature sensor is connected to the Base PRO system, and an additional outdoor temperature sensor connected to the Move PRO controller is not needed. The outdoor temperature sensor data will also be used by the other zones.

DE DK

The integration is activated when a zone is setup as Smatrix Base PRO (requires that the wiring is done and that Supply Water Controller is activated in the Integration menu in the Base PRO interface) in the startup wizard on the Move PRO controller.

EE ES

See section 5.10 Connect Uponor Smatrix Base PRO controller for more information.

Comfort ECO night 0 h 00

morning 6 h 00

afternoon 12 h 00

night

18 h 00

24 h 00

Other zones can, depending on system setup, simultaneously switch between Comfort and ECO mode according to their own programmed schedules.

FI

See section 5.13 Startup wizard for more information. See Uponor Smatrix Base PRO documentation for more information.

FR HR

Schedule 2 Comfort ECO night 0 h 00

morning 6 h 00

afternoon 12 h 00

18 h 00

HU

night 24 h 00

IT

Even if programmed schedules exist in the system, some zones may still operate without any scheduling. These zones will operate in constant Comfort mode and is not affected by the programming of other zones.

LT LV NL NO PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

11


UK

4

CZ

Install Uponor Smatrix Move PRO system

DE

4.1 Installation procedure DK

To determine where to best place the Uponor Smatrix Move PRO components, follow these guidelines:

U ponor S matrix M ove PRO Uponor recommends following the process described below to guarantee the best possible installation results.

EE

Stage

ES FI FR

IT

Page

• Ensure that the controller can be mounted close to 230 V AC supply.

1

Prepare for installation

12

2

Install Uponor Smatrix Move PRO controller

23

3

Connect sensors to the controller

24

4

Connect mixing valve actuators to the controller

36

4.3 Installation examples

5

Connect diverting valve actuators to the controller

37

The following sections describe a selection of installation examples with the Move PRO controller:

6

Connect circulation pumps to the controller

38

• Heating/cooling 2-pipe system in three different zones

7

Connect Uponor Smatrix Base PRO controller

40

• Heating/cooling 2-pipe system together with domestic hot water and meltaway production

8

Connect the controller to AC power

41

9

Startup wizard

41

10

Finishing installation

50

HR HU

Procedure

• Ensure that the controller can be installed close to the valve actuators, if possible.

4.2 Prepare for installation LT

Before starting the installation:

LV

• Verify the contents of the package with the packing list. See also section 3.3 Uponor Smatrix Move PRO components for identification of components.

NL

• Study the wiring diagram in the end of this manual or on the controller.

NO

2 230

-24

0V

Hz 50 L N

N 79 77 74

PL

21

22

23

24

25

26

27

28

29

72

75

• Heating/cooling 4-pipe system in three different zones • Heating/cooling 4-pipe system together with domestic hot water production

W arning ! Electrical installation and service behind secured 230 V AC covers must be carried out under the supervision of a qualified electrician. N OT E ! These are outline diagrams. Real systems must be installed according to applicable norms and regulations.

T

125

71

• Ensure that installed Uponor Smatrix Move PRO components are protected from running or dripping water, preferably in a cabinet.

mA

L

80

78

76

73

30

microSD

PT RO RU SE SK 12

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK H eating / cooling 2- pipe

The supply is routed to the zones from the heating and cooling sources using two diverting valves. This enables switching between heating and cooling in all zones simultaneously.

system in three

different zones

3

A

B

Base PRO

2

A

The zone temperatures are regulated using a wide range of sensors, by using either a three-way mixing valve (B) or a two-way valve together with a heat exchanger (A), set temperatures (setpoints), and other zone specific parameter settings.

DE

Example specific electrical connections

EE

DK

• The supply line diverting valve is connected to the terminals labelled 24 and 26.

B

Base PRO

1

CZ

ES

• The return line diverting valve is connected to the terminals labelled 25 and 26.

A

FI

• External signal for heating/cooling switch in all zones are connected to the terminals labelled 17 and 17 .

B

Base PRO

FR

See section 5 Install Uponor Smatrix Move PRO ­controller for more information.

HR

See also the wiring diagram in the end of the manual. Example specific system settings in startup wizard

HU

Operation Mode: Standard System Type: 2 Pipe

IT

Indoor Cooling Only: No Enable Zone # (# = 1, 2, and 3): Yes C

W arning ! Electrical installation and service behind secured 230 V AC covers must be carried out under the supervision of a qualified electrician.

Zone setup: Stand Alone Control, or Smatrix Base PRO

LT

HC Switchover: Indoor and Outdoor, Supply Water Temp., Contact Input, Force Heating, or Force Cooling.

LV

See section 4.3 Installation examples > Zone setup for more zone specific startup wizard settings.

NL

See section 5.13 Startup wizard for more information.

NO

See section 7.10 Settings for more information.

N OT E ! These are outline diagrams. Real systems must be installed according to applicable norms and regulations.

PL PT

This connection example shows an Uponor Smatrix Move PRO Controller (with the heating/cooling application installed) regulating three different heating/ cooling zones in a 2-pipe system.

RO

• Zone 1 is setup as Stand Alone Control or Smatrix Base PRO for heating/cooling.

RU

• Zone 2 is setup as Stand Alone Control or Smatrix Base PRO for heating/cooling.

SE

• Zone 3 is setup as Stand Alone Control or Smatrix Base PRO for heating/cooling.

SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

13


UK H eating / cooling 2- pipe

system together with

domestic hot water and meltaway production

CZ

3

DE

A

B

2

This connection example shows an Uponor Smatrix Move PRO Controller (with the heating/cooling application installed) regulating three different zones in a 2-pipe system.

ES

1

FI

Electrical installation and service behind secured 230 V AC covers must be carried out under the supervision of a qualified electrician. N OT E ! These are outline diagrams. Real systems must be installed according to applicable norms and regulations.

DK EE

W arning !

FR

A

• Zone 1 is setup as Stand Alone Control or Smatrix Base PRO for heating/cooling.

B

• Zone 2 is setup for Domestic Hot Water production. Base PRO

• Zone 3 is setup for melting snow with Meltaway. The supply is routed to zone 1 from the heating and cooling sources using two diverting valves, switching the zone between heating and cooling. Zones 2 and 3 are installed between the diverting valves and the heat source. This enables zones 2 and 3 to be operated independently from zone 1 (regardless if it is in heating or cooling mode).

HR HU IT

1

LT C

LV

The zone temperatures are regulated using a wide range of sensors, by using either a three-way mixing valve (B) or a two-way valve together with a heat exchanger (A), set temperatures (setpoints), and other zone specific parameter settings. N OT E ! When using a 3-way mixing valve (option B) in a meltaway zone, a heat exchanger may be needed. This creates a secondary loop where water mixed with antifreeze additives circulate.

NL NO PL PT RO RU SE SK 14

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Example specific electrical connections • The zone 1 supply and return line diverting valves are connected to the terminals labelled 24 and 26. Note! An external relay may be needed when connecting two diverting valves to the connection terminals.

CZ DE

• External signal for heating/cooling switch in zone 1 is connected to the terminals labelled 17 and 17 .

DK

See section 5 Install Uponor Smatrix Move PRO ­controller for more information.

EE

See also the wiring diagram in the end of the manual.

ES

Example specific system settings in startup wizard Operation Mode: Standard

FI

System Type: 2 Pipe Indoor Cooling Only: No Enable Zone # (# = 1, 2, and 3): Yes

FR

Zone setup (zone 1): Stand Alone Control, or Smatrix Base PRO

HR

Zone setup (zone 2): Domestic Hot Water Zone setup (zone 3): Meltaway

HU

HC Switchover: Indoor and Outdoor, Supply Water Temp., Contact Input, Force Heating, or Force Cooling.

IT

See section 4.3 Installation examples > Zone setup for more zone specific startup wizard settings.

LT

See section 5.13 Startup wizard for more information. See section 7.10 Settings for more information.

LV NL NO PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

15


UK H eating / cooling 4- pipe

system in three

W arning !

different zones

CZ

3

DE

Electrical installation and service behind secured 230 V AC covers must be carried out under the supervision of a qualified electrician.

A

B

Base PRO

DK

2

EE

A

B

ES

Base PRO

1

FI FR

N OT E ! These are outline diagrams. Real systems must be installed according to applicable norms and regulations. This connection example shows an Uponor Smatrix Move PRO Controller (with the heating/cooling application installed) regulating three different heating/ cooling zones in a 4-pipe system.

A

• Zone 1 is setup as Stand Alone Control or Smatrix Base PRO for heating/cooling.

B

• Zone 2 is setup as Stand Alone Control or Smatrix Base PRO for heating/cooling. Base PRO

HR

• Zone 3 is setup as Stand Alone Control or Smatrix Base PRO for heating/cooling. The supply is routed to the zones from the heating and cooling sources using four diverting valves. This enables zone 3 to be switched between heating and cooling independently from in zones 1 and 2 (which switch simultaneously).

HU IT

3

The zone temperatures are regulated using a wide range of sensors, by using either a three-way mixing valve (B) or a two-way valve together with a heat exchanger (A), set temperatures (setpoints), and other zone specific parameter settings.

1&2

LT C

LV NL NO PL PT RO RU SE SK 16

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Example specific electrical connections • The zone 1&2 supply and return line diverting valves are connected to the terminals labelled 24 and 26. Note! An external relay may be needed when connecting two diverting valves to the connection terminals.

CZ

• The zone 3 supply and return line diverting valves are connected to the terminals labelled 25 and 26. Note! An external relay may be needed when connecting two diverting valves to the connection terminals.

DK

• External signal for heating/cooling switch in zone 1 and 2 are connected to the terminals labelled 17 and 17 .

ES

• External signal for heating/cooling switch in zone 3 is connected to the terminals labelled 18 and 18 .

FI

DE

EE

See section 5 Install Uponor Smatrix Move PRO ­controller for more information.

FR

See also the wiring diagram in the end of the manual.

HR Example specific system settings in startup wizard Operation Mode: Standard

HU

System Type: 4 Pipe Indoor Cooling Only: No

IT

Enable Zone # (# = 1, 2, and 3): Yes Zone setup: Stand Alone Control, or Smatrix Base PRO

LT

Z1&2 Operation Mode: Heating And Cooling Z3 Operation Mode: Heating And Cooling

LV

See section 4.3 Installation examples > Zone setup for more zone specific startup wizard settings.

NL

See section 5.13 Startup wizard for more information. See section 7.10 Settings for more information.

NO PL PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

17


UK H eating / cooling 4- pipe

system together with

domestic hot water production

CZ

3

DE

W arning ! Electrical installation and service behind secured 230 V AC covers must be carried out under the supervision of a qualified electrician.

A

B

Base PRO

DK

2

EE

This connection example shows an Uponor Smatrix Move PRO Controller (with the heating/cooling application installed) regulating three different zones in a 4-pipe system.

ES

1

FI FR

A

• Zone 1 is setup as Stand Alone Control or Smatrix Base PRO for heating/cooling.

B

• Zone 2 is setup for Domestic Hot Water production. Base PRO

HR

3

1

LT C

LV

• Zone 3 is setup as Stand Alone Control or Smatrix Base PRO for heating/cooling. The supply is routed to zone 1 and 3 from the heating and cooling sources using four diverting valves, switching the zones between heating and cooling independently. Zone 2 is installed close to the heat source in permanent heating mode. This enables zones 2 to be operated independently from zones 1 and 3 (regardless if they are in heating or cooling mode).

HU IT

N OT E ! These are outline diagrams. Real systems must be installed according to applicable norms and regulations.

The zone temperatures are regulated using a wide range of sensors, by using either a three-way mixing valve (B) or a two-way valve together with a heat exchanger (A), set temperatures (setpoints), and other zone specific parameter settings.

NL NO PL PT RO RU SE SK 18

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Example specific electrical connections • The zone 1 supply and return line diverting valves are connected to the terminals labelled 24 and 26. Note! An external relay may be needed when connecting two diverting valves to the connection terminals.

CZ DE

• The zone 3 supply and return line diverting valves are connected to the terminals labelled 25 and 26. Note! An external relay may be needed when connecting two diverting valves to the connection terminals.

DK EE

• External signal for heating/cooling switch in zone 1 is connected to the terminals labelled 17 and 17 .

ES

• External signal for heating/cooling switch in zone 3 is connected to the terminals labelled 18 and 18 .

FI

See section 5 Install Uponor Smatrix Move PRO ­controller for more information.

FR

See also the wiring diagram in the end of the manual. Example specific system settings in startup wizard

HR

Operation Mode: Standard System Type: 4 Pipe

HU

Indoor Cooling Only: No Enable Zone # (# = 1, 2, and 3): Yes

IT

Zone setup (zone 1): Stand Alone Control, or Smatrix Base PRO Z1&2 Operation Mode: Heating And Cooling

LT

Zone setup (zone 2): Domestic Hot Water Zone setup (zone 3): Stand Alone Control, or Smatrix Base PRO

LV

Z3 Operation Mode: Heating And Cooling

NL

See section 4.3 Installation examples > Zone setup for more zone specific startup wizard settings.

NO

See section 5.13 Startup wizard for more information. See section 7.10 Settings for more information.

PL PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

19


UK Z one

setup

The zones can be setup as:

CZ

• Stand Alone Control • Smatrix Base PRO

DE

• Domestic Hot Water • Meltaway

DK

Stand Alone Control

The zone can switch between heating and cooling using one of the following functions (set in the startup wizard): • Indoor and Outdoor uses the indoor and outdoor temperatures to switch the zones between heating and cooling. • Supply Water Temp. uses the supply water temperature to switch the zones between heating and cooling. • Contact Input uses an external signal to switch the zones between heating and cooling.

EE

• Force Heating sets the zones in forced heating.

ES

• Force Cooling sets the zone in forced cooling. The outdoor temperature sensor is not needed if the Move PRO controller is integrated with an Uponor Smatrix Base PRO system (with outdoor temperature sensor).

FI FR

See section 5 Install Uponor Smatrix Move PRO controller for more information.

HR

If the zone (1 through 3) is setup as Stand Alone Control, basic control of the zone is enabled. The following components are required or optional for heating/cooling operation in the zone (regulate the zone temperature using a mixing valve).

HU IT

Required: • Supply sensor S-152 • Room sensor S-155 (optional for heating only)

LT

• Humidity sensor S-157 (optional for heating only) Optional:

LV

• Condensation sensor S-159 • Heating/Cooling Switch

NL

• Dehumidifier The optional dehumidifier can be connected to the controller instead of the circulation pump. If that option is chosen, then the circulation pump cannot be controlled by the Move PRO controller.

NO PL

SYSTEM SETTINGS IN STARTUP WIZARD Enable Zone # (# = 1, 2, or 3): Yes Zone setup: Stand Alone Control Z1&2 (or Z3) Operation Mode (4-pipe system only): Only Heating, Only Cooling, or Heating And Cooling Heating Mode: Outdoor (outdoor temperature sensor only) Outdoor + Indoor comp. (outdoor temperature sensor with optional room temperature sensor) Z1&2 (or Z3) HC Switchover (4-pipe system only): Indoor and Outdoor, Supply Water Temp., Contact Input, Force Heating, or Force Cooling Dehumidifier Control: Disable/Enable Condensation Sensor: No/Yes Other zone settings can be found in the menu system Settings > Zone # Setting (where # is the zone where Stand Alone Control is activated). See section 5.13 Startup wizard for more information.

PT

See section 7.10 Settings for more information.

RO RU SE SK 20

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Smatrix Base PRO

The optional dehumidifier can be connected to the controller instead of the circulation pump. If that option is chosen, then the circulation pump cannot be controlled by the Move PRO controller.

CZ DE

C aution ! PRO PRO

D

The integration is activated when a zone is setup as Smatrix Base PRO (requires that the wiring is done and that Supply Water Controller is activated in the Integration menu in the Base PRO interface) in the startup wizard on the Move PRO controller.

DK EE

See section 5 Install Uponor Smatrix Move PRO controller for more information.

ES

SYSTEM SETTINGS IN STARTUP WIZARD If the zone (1 through 3) is setup as Smatrix Base PRO, individual room control in the zone is enabled.

Enable Zone # (# = 1, 2, or 3): Yes

The controller is connected to an Uponor Smatrix Base PRO system, via the Smatrix Base PRO bus, utilising its components to regulate the zone temperature.

Z1&2 (or Z3) Operation Mode (4-pipe system only): Only Heating, Only Cooling, or Heating And Cooling

The following components are required or optional for heating/cooling operation in the zone (regulate the zone temperature using a mixing valve).

Heating Mode: Outdoor (outdoor temperature sensor only) Outdoor + Indoor comp. (outdoor temperature sensor with optional room temperature sensor)

Required: • Supply sensor S-152 • Smatrix Base PRO system Optional: • Condensation sensor S-159 • Heating/Cooling Switch • Dehumidifier The outdoor temperature sensor is connected to the Base PRO system via a thermostat, registered as a system device. The thermostat is preferably placed in a non-public area such as a technical room. Heating/cooling mode is set from the Smatrix Base PRO system.

FI

Zone setup: Smatrix Base PRO

FR HR HU

Smatrix Indoor Temperature: Worst Case (the measured worst case temperature in the zone), or Average (the calculated average temperature in the zone).

IT

Z1&2 (or Z3) HC Switchover (4-pipe system only): Indoor and Outdoor, Supply Water Temp., Contact Input, Force Heating, or Force Cooling

LT LV

Dehumidifier Control: Disable/Enable Condensation Sensor: No/Yes

NL

Assign Controller to zone: Assign connected Smatrix Base PRO controllers to zones.

NO

Other zone settings can be found in the menu system Settings > Zone # Setting (where # is the zone where Smatrix Base PRO is activated).

PL

See section 5.13 Startup wizard for more information. See section 7.10 Settings for more information.

PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

21


UK Domestic Hot Water

Meltaway

CZ DE DK EE ES

If the zone is setup as Domestic Hot Water, hot water production is enabled in the zone.

FI

C aution !

FR

The Domestic Hot Water function requires a constant delivery of heating supply water, such as district heating.

HR

The following components are required for regulating the hot water temperature in the zone (regulate the supply temperature using a mixing valve). Required:

HU

• Supply sensor S-152 • Return sensor S-152

IT

N OT E ! If the zone is setup as Domesitc Hot Water without a return sensor, the zone will work with reduced functionality. Functions such as BoostPower and hot water recirculation requires a return sensor to work properly.

LT LV

See section 5 Install Uponor Smatrix Move PRO controller for more information.

NL

SYSTEM SETTINGS IN STARTUP WIZARD Enable Zone 2: Yes

NO

Zone setup: Domestic Hot Water Other zone settings can be found in the menu system Settings > Zone # Setting (where # is the zone where Domestic Hot Water is activated).

PL

See section 5.13 Startup wizard for more information.

PT

See section 7.10 Settings for more information.

RO

If the zone is setup as Meltaway, hot water production for snow melting (keeping large areas clear of snow) is enabled in the zone. The following components are required for snow melting hot water production in the zone (regulate the supply temperature using a mixing valve). Required: • Supply sensor S-152 • Return sensor S-152 • Primary return sensor S-152 (not shown in illustration) • Snow sensor S-158 used as ground temperature sensor • Snow sensor S-158 used as ground moisture sensor The outdoor temperature sensor is not needed if the Move PRO controller is integrated with an Uponor Smatrix Base PRO system (with outdoor temperature sensor). See section 5 Install Uponor Smatrix Move PRO controller for more information. SYSTEM SETTINGS IN STARTUP WIZARD Enable Zone 3: Yes Zone setup: Meltaway Other zone settings can be found in the menu system Settings > Zone # Setting (where # is the zone where Melt away is activated). N OT E ! When using a 3-way mixing valve (option B) a heat exchanger may be needed, creating a secondary loop where water mixed with antifreeze additives circulate. See section 5.13 Startup wizard for more information.

RU

See section 7.10 Settings for more information.

SE SK 22

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK

5 Install Uponor Smatrix Move PRO ­controller

CZ DE

5.1 Placement of controller

5.3 Attach stickers

Refer to the installation preparation guidelines (see section 4.2 Prepare for installation), and use the following guidelines when positioning the controller:

Attach the stickers from the application package to the controller.

DK EE

• Position the controller close to at least one of the actuators, preferably inside a cabinet. Check the position of the 230 V AC supply.

ES 4

4 5

5 6

6 7

7 8

8 9

9 10

10 11

11 12

12 13

13 14

14 15

15 16

16

18 17 18 17

FI

41

42

43

44

45

46

47

48

49

15VDC

3

50

51

52

GND

3

53

54

GND

2

12VDC IN

2

55

24VAC IN

1

• Check that connectors and switches are easily accessible.

1

1

• Check that the terminal cover can be easily removed from the controller.

56

FR

1

5.2 Select controller application

1

The controller is delivered with two packages containing applications for different use of the controller. The package contains a microSD card, electrical connection stickers, and an application diagram depicting installation examples.

HR

2 2

2

N

L

T 125

N 79

Select the package containing the heating and cooling application and discard the other one.

75

74 71

21

22

23

24

25

26

76

73

72

30

29

28

27

HU

mA

L

80

78

77

IT

oSD micr

1T L

L

Hz

56 55 49

77

3 48

N L

2

47 46

75

2 45

74

44

1

73

43

1 72 71

41 Base PRO

30 29

27 26

3

25 24

1/2

12 13

23

3B

BASE – BUS

A

22

Base

PRO

-

10 11 11 12

LV

21

PRO SMATRIX

5.4 Insert microSD card

7 8

2

6 7 3 4

1

2 3 1 2

microSD

Base PRO

Base PRO

1

1

1

microSD

microSD

2

3 4

4 5

4 5

5 6

5 6

6 7

3

7 8

8 9

8 9

9

9

10

28

1/2

3

25

13 14 14 15 15 16 16 17 17 18 18

3

26

44

72

42

71

41

30

Base PRO

29 28 27 26

3/4

4

25

13 14 14 15 15 16 16 17 17 18 18

3

24

12 13

23

4B A

22 21

BASE – BUS

42

1

1

43

73

IIN ≤ 6A

Base

76

76

2

46

75

2 45

74 N L

!

PRO

N L

49

3

77

3 48

N L

IIN ≤ 6A

47

!

-

N

N

V± 50/60 10%

54 53

230

80

52

79

51

3

50

78

IIN ≤ 1A

78

!

PRO SMATRIX

IIN ≤ 6A

10 10 11 11 12

!

2 3

IIN ≤ 6A

1 2

!

microSD

mA 125

mA

L

4

79

51

4 N L

N L

Hz

55

L

N

N

V± 50/60 10%

54

230

53

N L

80

IIN ≤ 1A

52

!

50

GND 12VDC IN GND

15VDC

IIN ≤ 1A

GND 12VDC IN GND

15VDC

24VAC IN

!

56

125

1T

2

2

LT 24VAC IN

Insert the microSD card from the application package in to the controller.

NL 2

N

L

T 125

N 79 77 74 71

21

micro

22

23

24

25

26

27

28

29

72

75

mA

NO

L

80

78

76

73

30

PL

SD

PT

microSD

RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

23


UK

5.5 Attach controller to the wall

5.6 Terminal cover

CZ

DIN

DE

Attach the controller to a DIN rail in a cabinet (recommended), or to a DIN rail attached to a wall using screws and wall plugs.

The illustration below shows how to remove and reattach the terminal cover.

DK

The figure below shows how to attach the controller using a DIN rail.

rail

2

N

T 125

N 79 77 74 71

21

EE

L

22

23

24

25

26

27

28

29

72

75

mA

L

80

78

76

73

30

SD

micro

ES

A 5.7 Connect sensors to controller

B

FI

The following sensors can be connected to the system: • Uponor Smatrix Outdoor S-1XX

FR

A

2

HR

• Uponor Smatrix Move Sensor Supply/Return S-152

B

• Uponor Smatrix Move PRO Sensor Room S-155 • Uponor Smatrix Move PRO Sensor Humidity S-157

1

HU

3

3

2 1

C aution !

LT

Make sure the controller cannot slide off the DIN rail if mounting it in any other position than horizontal.

LV NL

• Uponor Smatrix Condensation Set S-159

W arning !

CLICK

IT

• Uponor Smatrix Move PRO Sensor Snow S-158

Electrical installation and service behind secured 230 V AC covers must be carried out under the supervision of a qualified electrician.

C aution ! Make sure shielded cables are used when connecting sensors to the controller to prevent interference from power sources and cables.

NO PL PT RO RU SE SK 24

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK O utdoor

Connect outdoor sensor to controller

sensor

The outdoor sensor is mandatory and must always be installed. Either directly to the Move PRO controller or via an integrated Uponor Smatrix Base PRO controller. If a Base PRO controller is integrated to the system, it is a requirement to connect the outdoor temperature sensor to the Base PRO controller via a thermostat, registered as a system device. The thermostat is preferably placed in a non-public area such as a technical room.

The illustration below shows the outdoor sensor connected to the controller.

CZ DE

S-1XX DK #

Placement of outdoor sensor

16

Refer to the installation preparation guidelines (see section 4.2 Prepare for installation), and use the following guidelines when positioning the outdoor sensor: 1. Attach the outdoor sensor to the north side of the building where it is unlikely to be exposed to direct sunlight. 2. Ensure that the outdoor sensor is placed away from doors, windows, or air outlets.

X-159

ES

To connect an outdoor sensor to the controller:

FI

1. Ensure that the power is disconnected from the controller.

FR

2. Remove the terminal cover. See section 5.6 Terminal cover for more information. 3. Study the wiring diagram to locate the connection terminal positions.

N W

EE

E S

HR

4. Connect the wires from the outdoor sensor to terminals 16 and 16 on the controller.

HU

5. Tighten the screws fixing the wires to the connector.

IT LT LV NL NO PL PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

25


UK S upply

R eturn

sensor

The supply sensor needs to be installed in all zones.

CZ

sensor

The return sensor only needs to be installed in zones setup as Meltaway or DHW (domestic hot water).

Connect supply sensor to controller The illustration below shows supply sensors connected to the controller.

DE

1

DK

2

3

S-152

Connect return sensor to controller The illustration below shows return sensors connected to the controller.

2

3

6

10

S-152

EE #

ES

1

FI

5

9

#

X-159 X-159

FR

To connect a supply sensor to the controller: 1. Study the wiring diagram to locate the connection terminal positions.

HR

2. Ensure that the power is disconnected from the controller.

HU

3. Remove the terminal cover. See section 5.6 Terminal cover for more information.

IT

4. Connect the wires from the supply sensor to the controller.

LT LV

• ZONE 1: Terminals 1 and 1 .

• ZONE 2: Terminals 5 and 5 .

• ZONE 3: Terminals 9 and 9 .

5. Tighten the screws fixing the wires to the connector.

To connect a return sensor to the controller: 1. Study the wiring diagram to locate the connection terminal positions. 2. Ensure that the power is disconnected from the controller. 3. Remove the terminal cover. See section 5.6 Terminal cover for more information. 4. Connect the wires from the return sensor to the controller.

• ZONE 2: Terminals 6 and 6 .

• ZONE 3: Terminals 10 and 10 .

5. Tighten the screws fixing the wires to the connector.

NL NO PL PT RO RU SE SK 26

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK R oom

Label room sensor

sensor

The room sensor only needs to be installed in zones setup as Stand Alone, with Heating Mode setup as Outdoor + Indoor comp.. N OT E ! The sensor is required in zones where heating/cooling (or cooling only) is enabled. Otherwise (heating only) it is only optional. Placement of room sensor

Label the room sensors, where suitable, with the zone numbers they are to control, for example, #02, #03.

CZ

Attach room sensor to the wall

DE

The illustration below shows room sensor mounting hole positions and how to attach it to the wall using screws and wall plugs. 60

DK

mm

EE

Refer to the installation preparation guidelines (see section 4.2 Prepare for installation), and use the following guidelines when positioning the room sensors:

ES

1. Select an indoor wall and a position 1.3 m to 1.5 m above the floor.

FI

2. Ensure that the room sensor is away from direct solar radiation. 3. Ensure that the room sensor will not be heated through the wall by sunshine.

FR

4. Ensure that the room sensor is away from any source of heat, for example television set, electronic equipment, fireplace, spotlights, and so on.

HR

5. Ensure that the room sensor is away from any source of humidity and water splashes (IP20).

HU IT LT

1.3–1.5 m LV NL NO PL PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

27


UK CZ

Connect room sensor to controller

To connect a room sensor to the controller:

The illustration below shows room sensors connected to the controller.

1. Study the wiring diagram to locate the connection terminal positions.

1

DE

2

S-155

3

2. Ensure that the power is disconnected from the controller. 3. Remove the terminal cover. See section 5.6 Terminal cover for more information.

DK

4. Route the wires through points A or B. #

EE

2

ES

6

5. Connect the wires from the room sensor to the controller.

10

X-159

FI

1

FR HR

A

• ZONE 1: Terminals 2 and 2 .

• ZONE 2: Terminals 6 and 6 .

• ZONE 3: Terminals 10 and 10 .

6. Tighten the screws fixing the wires to the connector.

S-155

B

HU C aution !

IT

Do not change the jumper setting, otherwise the function of the sensor will be compromised.

LT

Default setting:

LV NL NO PL PT RO RU SE SK 28

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK H umidity

sensor

The humidity sensor only needs to be installed in zones setup as Stand Alone. N OT E ! The sensor is required in zones where heating/cooling (or cooling only) is enabled. Placement of humidity sensor Refer to the installation preparation guidelines (see section 4.2 Prepare for installation), and use the following guidelines when positioning the humidity sensors:

Label humidity sensor Label the humidity sensors, where suitable, with the zone numbers they are to control, for example, #02, #03.

The illustration below shows humidity sensor mounting hole positions and how to attach it to the wall using screws and wall plugs. 60

3

2. Ensure that the humidity sensor is away from direct solar radiation.

DK EE

mm

A

ES

10 V 0V +24 V

3. Ensure that the humidity sensor will not be heated through the wall by sunshine.

5. Ensure that the humidity sensor is away from any source of humidity and water splashes (IP30).

DE

Attach humidity sensor to the wall

1. Select an indoor wall and a position 1.3 m to 1.5 m above the floor.

4. Ensure that the humidity sensor is away from any source of heat, for example television set, electronic equipment, fireplace, spotlights, and so on.

CZ

1

FI

2

FR

60 mm

HR 50 mm

HU IT LT

1.3–1.5 m

LV NL NO PL PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

29


UK CZ

Connect humidity sensor to controller

To connect a humidity sensor to the controller:

The illustrations below shows humidity sensors connected to the controller.

1. Study the wiring diagram to locate the connection terminal positions.

1

DE

2

S-157

3 10 V 0V +24 V

10 V 0V +24 V

10 V 0V +24 V

3. Remove the terminal cover. See section 5.6 Terminal cover for more information.

DK

4. Route the wires through one of the points A. See Attach humidity sensor to the wall for more information.

#

EE

4

8

2. Ensure that the power is disconnected from the controller.

12

5. Connect the wires from the humidity sensor to the controller.

ES

X-159

FI 1

2

S-157

3

10 V 0V +24 V 10 V 0V +24 V 10 V 0V +24 V

FR HR

41

44

47

HU

ZONE 1:

• Control signal wires to terminals 4 and 4 .

• 24 V AC wire to terminal 41

ZONE 2:

• Control signal wires to terminals 8 and 8 .

• 24 V AC wire to terminal 44

ZONE 3:

• Control signal wires to terminals 12 and 12 .

• 24 V AC wire to terminal 47

6. Tighten the screws fixing the wires to the connector.

IT 10 V 0V

LT

+24 V

S-157

24 VAC

#

LV NL NO PL PT RO RU SE SK 30

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK S now

sensor

The snow sensor only needs to be installed in zones setup as Meltaway.

CZ

C aution !

DE

Two snow sensors are needed to guarantee the Meltaway function. One of them is used as a ground temperature sensor and the other one as a ground moisture sensor. When installing the snow and ice sensors in a zone a primary return sensor, and secondary supply and return temperature sensors are needed. See section 5.7 Connect sensors to controller for more information.

≥ 0,2 m

DK

≥ 0,1 m

EE m 3m

≤2

≤2

00m

ES FI

Placement of the snow sensor sensors The following requirements must be met when installing the snow sensor.

FR

• The snow sensor must be installed within the area to be heated. • The snow sensor must be installed levelled horizontally and embedded in a hard surface (such as concrete or asphalt). • The snow sensor must not protude from the surface. It can be recessed a few millimeters into the surface to allow draining melt water to collect on the sensor surface. Not too deep though. • The snow sensor must be installed in an open unsheltered position away from walls and exposed to the elements (eg. not close to walls, fan outlets, or other sources which can affect the sensors).

HR

A

HU IT

B LT LV

• If the snow sensor is to be used as a ground temperature sensor it must not be installed closer than 20 cm to the heating loop.

NL

• If the snow sensor is to be used as a ground moisture sensor it must not be installed closer than 10 cm to the heating loop.

NO

• If the ground is not horizontal, then the ground moisture sensor must be installer lower than the ground temperature sensor.

PL

• Use a cable conduit with a diameter of up to 23 mm when routing the sensor cables.

PT

• The sensor cable (supplied with 25 m) can be extended to up to 200 m using standard installation cable (6x1.5 mm2). The total resistance of the cable must be less than 10 ohm.

RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

31


UK Install snow sensor into the ground surface The following illustrations show how to install the snow sensor into the ground surface. 1. Create a notch for the cable conduit (maximum diameter of 23 mm). It is recommended to use a cable conduit equipped with a cord, in order to make it easier to pull the cable through when installed.

CZ DE DK

5. Remove the wood plug when the concrete/asphalt has cured.

EE 6. Ensure that the sunsor tube is clean.

ES m

3m

FI

≤2

FR

2. Insert the sensor tube in the hole where the sensor is to be installed. Make sure it is securely embedded in relation to the expected surface load.

HR

7. Insert the sensor cable and route it into the cable conduit. Ensure that the cable is not damaged on any sharp edges.

HU IT LT 3. Insert the supplied wood plug into the sensor tube before applying the concrete/asphalt.

LV NL

8. Place the snow sensor into the tube. Make sure that the cable easily fits in the hole in the bottom.

NO

Secure the sensor (in the middle of the sensor) with the supplied screw.

PL PT 4. Apply the concrete/asphalt.

RO RU SE SK 32

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Connect snow sensor, used as ground temperature sensor, to controller

Connect snow sensor, used as ground moisture sensor, to controller.

The illustration below shows the snow sensor, used as ground temperature sensor, connected to the controller.

The illustration below shows the snow sensor, used as ground moisture sensor, connected to the controller.

S-158

S-158

3

CZ DE

3

DK EE #

#

14

13

ES

X-159

X-159

FI

To connect a snow sensor to the controller:

FR

25 26

1. Study the wiring diagram to locate the connection terminal positions.

S-158 HR

2. Ensure that the power is disconnected from the controller. 3. Remove the terminal cover. See section 5.6 Terminal cover for more information. 4. Connect the wires from the snow sensor to the controller.

ZONE 3:

• Pink wire to terminal 13

• Grey wire to terminal 13

5. Tighten the screws fixing the wires to the connectors.

3

HU

To connect a snow sensor to the controller: 1. Study the wiring diagram to locate the connection terminal positions.

IT

2. Ensure that the power is disconnected from the controller.

LT

3. Remove the terminal cover. See section 5.6 Terminal cover for more information.

LV

4. Connect the wires from the snow sensor to the controller.

ZONE 3:

• White wire to terminal 14

• Yellow wire to terminal 14

• Brown wire to terminal 25

• Green wire to terminal 26

NL NO PL

5. Tighten the screws fixing the wires to the connectors.

PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

33


UK P rimary

C ondensation

return sensor

The primary return sensor may only need to be installed in zones setup as Meltaway.

CZ

3

The condensation kit consist of a relative humidity sensor connected to a converter, which in turn is connected to the Move PRO controller. The sensor measures the relative humidity of the air flowing through its capilary tubes and translates it to electrical resistance. If the electrical resistance drops to about 8 MΩ (about 80-85 % relative humidity) the converter opens the signal to the Move PRO controller, which shuts of cooling. When the electrical resistance reaches approximately 16 MΩ the signal to the controller is closed and cooling is allowed again.

15

Cut capilary tubes on the condensation sensor

Connect primary return sensor to controller

DE

The illustration below shows a primary return sensor connected to the controller.

DK

S-152

EE ES

sensor kit

The condensation sensor kit is optional for zones setup as Stand Alone or Smatrix Base PRO.

#

FI X-159 FR

The illustration below shows the capilary tubes beeing cut to allow air flow through the sensor (to measure relative humidity).

To connect a primary return sensor to the controller: 1. Study the wiring diagram to locate the connection terminal positions.

HR

2. Ensure that the power is disconnected from the controller.

HU

3. Remove the terminal cover. See section 5.6 Terminal cover for more information.

IT

4. Connect the wires from the primary return sensor to the controller.

LT

• ZONE 3: Terminals 15 and 15 .

Attach condensation sensor to the supply pipe The illustration below shows the condensation sensor attached to the supply pipe using cable straps.

5. Tighten the screws fixing the wires to the connector.

LV

S econdary

supply and return sensors

The secondary supply or return sensor is connected as a standard supply or return sensor.

NL

See section 5.7 Connect sensors to controller > Supply sensor for more information.

NO

See section 5.7 Connect sensors to controller > Return sensor for more information.

PL PT RO RU SE SK 34

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Attach converter to DIN rail

C aution !

The illustration below shows the attached to a DIN-rail.

Maximum lenght of the sensor cable is 10 meters.

CZ

To connect a condensation sensor kit to the controller:

DE

1. Study the wiring diagram to locate the connection terminal positions.

B 2

A 1

2. Ensure that the power is disconnected from the controller.

A B

3. Remove the terminal cover. See section 5.6 Terminal cover for more information.

EE

3

4. Connect the condensation sensor to terminals 1 and 2 on the the converter.

ES

3

2

CLICK

1 The illustration below shows a condensation sensor kit connected to the controller.

2 24 V AC

3

24 V AC

Note! Use one condensation sensor kit (converter and sensor) per zone where it is to be used.

FI

5. Connect the the converter to the controller.

Connect condensation sensor kit to controller

1

DK

S-159

ZONE 1:

• Converter terminal 3 to controller terminal 3.

• Converter terminal 4 to controller terminal 3

ZONE 2:

• Converter terminal 3 to controller terminal 7.

• Converter terminal 4 to controller terminal 7

FR HR HU

24 V AC

7 6 24V~

7 6 24V~

7 6 24V~

ZONE 3:

1 2 3 4 5

1 2 3 4 5

1 2 3 4 5

• Converter terminal 3 to controller terminal 11.

• Converter terminal 4 to controller terminal 11

IT LT

6. Connect the converter to 24 V AC. # 3

7

11

X-159

• L to converter terminal 6.

• N to converter terminal 7.

LV

Note! Use one condensation sensor kit (converter and sensor) per zone where it is to be used.

NL

7. Tighten the screws fixing the wires to the connectors.

NO PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

35


UK

5.8 Connect external signal for heating/cooling switch to the controller

5.9 Connect mixing valve actuators to the controller

DE

The external signal for heating/cooling switch is optional for zones setup as Stand Alone.

The illustration below shows actuators connected to the controller.

DK

A total of two external signals for heating/cooling switch can be connected to the controller. One external signal controls zone 1 and/or zone 2, depending on zone setup. The other one controls zone 3.

CZ

EE

The controller can control up to 3 different zones.

1 -

2 +

-

3 +

-

+

The illustration below shows external signals for heating/cooling switch connected to the controller.

ES

1&2

42 43

3

45 46

48 49

X-159

FI

W arning !

FR

#

Electrical installation and service behind secured 230 V AC covers must be carried out under the supervision of a qualified electrician.

17 18

HR X-159

N OT E ! Only the control signals from the vavle acutators are connected to the Move PRO controller. Power must be obtained from an external source.

HU To connect an external signal for heating/cooling switch to the controller:

IT

1. Ensure that the power is disconnected from the controller. 2. Remove the terminal cover. See section 5.6 Terminal cover for more information.

LT LV

3. Study the wiring diagram to locate the connection terminal positions.

NL

4. Connect the wires for heating/cooling switch to the controller.

NO

• ZONE 1&2: Terminals 17 and 17 .

• ZONE 3: Terminals 18 and 18 .

5. Tighten the screws fixing the wires to the connector.

To connect valve actuators to the controller: 1. Ensure that the power is disconnected from both the controller and the actuator. 2. Remove the terminal cover. See section 5.6 Terminal cover for more information. 3. Study the wiring diagram to locate the connection terminal positions. 4. Connect the wires from the actuator to the controller.

ZONE 1: • 0...10 V wire to terminal 43.

• Ground wire (   ) to terminal 42.

ZONE 2: • 0...10 V wire to terminal 46.

• Ground wire (   ) to terminal 45.

RO

ZONE 3: • 0...10 V wire to terminal 49.

RU

• Ground wire (   ) to terminal 48.

PL PT

5. Tighten the screws fixing the wires to the connector.

SE SK 36

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK

5.10 Connect diverting valve actuators to the controller

W arning ! Electrical installation and service behind secured 230 V AC covers must be carried out under the supervision of a qualified electrician.

The controller can control up to 3 different zones. The illustration below shows actuators in a 2 pipe setup connected to the controller.

CZ DE

N OT E ! Only the control signals from the vavle acutators are connected to the Move PRO controller. Power must be obtained from an external source.

X-159

24 25 26

DK EE

To connect valve actuators or external relays to the controller:

ES

1. Ensure that the power is disconnected from both the controller and the actuator.

3 1&2

FI

2. Remove the terminal cover. See section 5.6 Terminal cover for more information.

C aution !

3. Study the wiring diagram to locate the connection terminal positions.

An external relay may be needed when connecting two diverting valves to the connection terminals (24 V AC output). The illustration below shows diverting valves in a 4 pipe setup connected to the controller using external relays.

X-159

24 25 26

3

FR

4. Connect the wires from the actuator (or relay) to the controller.

ZONE 1&2 (4 pipe)/Supply line (2 pipe):

• 24 V AC wire to terminal 24.

• Ground wire (   ) to terminal 26.

ZONE 3 (4 pipe)/Return line (2 pipe):

• 24 V AC wire to terminal 25.

• Ground wire (   ) to terminal 26.

HR HU IT LT

5. Tighten the screws fixing the wires to the connector.

LV NL 1&2

NO PL PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

37


UK

5.11 Connect circulation pumps to the controller

CZ

W arning ! Electrical installation and service behind secured 230 V AC covers must be carried out under the supervision of a qualified electrician.

The controller can control either a circulation pump or a dehumidifier in up to 3 different zones.

DE

The illustration below shows circulation pumps connected to the controller.

DK

1. Ensure that the power is disconnected from the controller.

X-159

2. Remove the terminal cover. See section 5.6 Terminal cover for more information.

EE 75 76

72 73

To connect circulation pumps or external relays to the controller:

77 78

3. Study the wiring diagram to locate the connection terminal positions.

ES L N

L N

24 V AC / 230V AC

L N

FI 1

FR

2

3

C aution ! The terminals are limited to 1A. An external relay might be needed.

HR

The illustration below shows a circulation pump connected to the controller using external relays.

HU

X-159

IT LT

L

LV

N N L

NL

24 V AC / 230V AC

4. Connect power (max 230VAC) to the circulation pumps/external relays via connection terminals on the controller. Caution! The terminals are limited to 1A. An external relay might be needed.

ZONE 1:

• Power (L) from the circulation pump to terminal 72.

• External 24 or 230 V A C (L) to terminal 73.

ZONE 2:

• Power (L) from the circulation pump to terminal 75.

• External 24 or 230 VAC (L) to terminal 76.

ZONE 3:

• Power (L) from the circulation pump to terminal 77.

• External 24 or 230 VAC (L) to terminal 78.

5. Connect the common wire (N) from the circulation pumps to external connection. 6. Tighten the screws fixing the wires to the connector.

NO PL PT RO RU SE SK 38

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK

5.12 Connect a dehumidifier to the controller

W arning ! Electrical installation and service behind secured 230 V AC covers must be carried out under the supervision of a qualified electrician.

The controller can control either a dehumidifier or a circulation pump in up to 3 different zones. The illustration below shows dehumidifiers connected to the controller.

CZ DE

To connect dehumidifiers or external relays to the controller:

DK

1. Ensure that the power is disconnected from the controller.

X-159

75 76

72 73

L N

2. Remove the terminal cover. See section 5.6 Terminal cover for more information.

77 78

L N

24 V AC / 230V AC

L N

3. Study the wiring diagram to locate the connection terminal positions.

2

3

C aution ! The terminals are limited to 1A. An external relay might be needed. The illustration below shows dehumidifiers connected to the controller via dry contact.

ES

4. Connect the dehumidifier to the controller.

1

EE

FI

4.1 Connect power (max 230VAC) to the dehumidifiers/external relays via connection terminals on the controller. Caution! The terminals are limited to 1A. An external relay might be needed.

FR

ZONE 1: • Power (L) from the dehumidifier to terminal 72.

HR

HU

• External 24 or 230 VAC (L) to terminal 73.

ZONE 2: • Power (L) from the dehumidifier to terminal 75.

X-159

72 73

75 76

77 78

IT

• External 24 or 230 VAC (L) to terminal 76.

LT

ZONE 3: • Power (L) from the dehumidifier to terminal 77.

1

2

3

The illustration below shows a dehumidifier connected to the controller using external relays.

X-159

LV

• External 24 or 230 VAC (L) to terminal 78.

4.2 Connect the dry contact in the dehumidifiers to the connection terminals on the controller.

NL

ZONE 1: • Dry contact to terminals 72-73.

NO

ZONE 2: • Dry contact to terminals 75-76.

PL

ZONE 3: • Dry contact to terminals 77-78. L N

24 V AC / 230V AC

N L

PT

5. Connect the common wire (N) from the dehumidifiers to external connection. 6. Tighten the screws fixing the wires to the connector.

RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

39


UK CZ DE DK

5.13 Connect Uponor Smatrix Base PRO controller

4. Study the wiring diagrams of both controllers to locate the connection terminal positions.

The controller can be connected to an Uponor Smatrix Base PRO system bus for integration with Base PRO controllers and thermostats.

5. Connect the wires from the Base PRO controller to the Move PRO controller.

Uponor Smatrix Base PRO:

The illustration below shows the Uponor Smatrix Base Pro system bus connected to the controller.

• Communication wire to system bus terminal A, B and -.

Uponor Smatrix Move PRO:

• Communication wire to system bus terminal 21 (-), 22 (A) and 23 (B).

X-159 EE - A B 21 22 23

ES

- A B 21 22 23

FI

6. Tighten the screws fixing the wires to the connector. Enable the Move PRO controller in the Smatrix Base PRO interface I-147: 7. Go to the Integration menu (Main menu > Integration).

FR

A B - A B -

A B - A B -

X-147

HR

8. Press Supply Water Controller: Disable. 9. Press Enable to activate communication between the interface and the Move PRO controller. 10. Assign controllers at the end of the Startup Wizard in the Move PRO controller. Connected Smatrix Base PRO controllers will be shown in a list automatically. See section 5.14 Startup wizard for more information.

HU IT

W arning ! Electrical installation and service behind secured 230 V AC covers must be carried out under the supervision of a qualified electrician.

LT LV

To connect an Uponor Smatrix Base PRO system bus to the controller:

NL

1. Ensure that the power is disconnected from all controllers.

NO

2. Remove the terminal cover on the Move PRO controller. See section 5.6 Terminal cover for more information.

5.14 Connect Modbus RTU interface The controller can be connected and integrated to a building management system (BMS) through a Modbus-RTU interface over RS-232. See separate documentation for more information about BMS integration.

3. Remove the cover on (one of) the Base PRO controllers. See Uponor Smatrix Base PRO documentation for more information.

PL PT RO RU SE SK 40

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK

5.15 Connect the controller to AC power

5.17 Startup wizard

The illustration below shows the the controller connected to AC power.

The controller initiates a startup wizard the first time it is started, or after a factory reset. This wizard is designed to configure the controller zones. Further settings can be done in the Settings menu.

X-159

N L

CZ DE

It can also be started manually through the menu system, Settings > Installer Settings > Restart wizard.

DK

N OT E ! The display on the controller can start flashing when powered on. This is completely normal and the regular operation will continue shortly after.

N L 230 V 50 Hz

EE ES

C aution !

W arning !

FI

At least one zone must be enabled when setting up the controller. Otherwise a configuration error will appear and the startup wizard is restarted.

Electrical installation and service behind secured 230 V AC covers must be carried out under the supervision of a qualified electrician. To connect the controller to AC power:

N avigating

1. Check that all wiring is complete and correct:

Select/change

• Sensors • Valve actuators • Circulation pump

Turn the control wheel to select an option, or to change a parameter setting.

FR

the startup wizard

HR HU

2. Connect the 230 V AC power cable to connection terminals N (blue) and L (brown).

IT

3. Ensure that all terminal covers are attached correctly.

LT

4. Connect the power cable to a 230 V AC wall socket, or if required by local regulations, to a junction box.

LV

5.16 Alternate power inputs The controller has connection terminals for alternate power inputs (connection terminals 52 – 56).

C aution ! Do not use these input terminals, unless instructed to by Uponor technical support.

NL Confirm

NO

Press the control wheel to confirm a selection or parameter setting.

PL PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

41


UK CZ

1. Set language

4. Select Operation Mode

Select operation mode of the controller.

• Select Standard to continue setting up the controller for heating/cooling operation.

• Select Pre Heating to enable pre heating operation mode in the controller.

DE

Select the language which is to be used in the controllers menu system. Language English Deutsch Espanol Swedish

DK

See section 5.17 Pre heating concrete slab (DIN 1264-4) for more information.

2. Set the time

EE

Set the time of the system, starting with the hours.

Time

Standard Pre Heating

Enter the hours

12:34

ES

hh:mm

FI

Time Enter the minutes

12:34 hh:mm

FR

5. System Type

Select system type, 2 Pipe or 4 Pipe hydraulic delivery system.

• 2 Pipe means that all zones setup as Stand Alone Control or Smatrix Base PRO switches between heating and cooling at the same time.

• 4 Pipe means that zones 1 and 2, and zone 3, switches between heating and cooling independently from each other.

Individual zones can still be setup as Domestic Hot Water or Meltaway if needed. Those zones will not be affected by this setting, as long as their supply pipes are placed before the heating/cooling diverting valves..

3. Set the date HR

Set the date of the system, starting with the day. Date Enter the day

Tue 01.06.2016

HU IT

Date Enter the month

Tue 01.06.2016

LT

LV

System Type 2 Pipe 4 Pipe

Date Enter the year

Tue 01.06.2016

6. Indoor Cooling Only

NL

Operation Mode

This setting is only shown if 2 Pipe is selected in the System Type menu.

Select Yes to enable cooling only (No enables heating/cooling) in the system.

NO

PL PT

Individual zones can still be setup as Domestic Hot Water or Meltaway if needed. Those zones will not be affected by this setting, as long as their supply pipes are placed before the heating/cooling diverting valves.. Indoor Cooling Only No Yes

RO RU SE SK 42

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK 7. Enable Zone 1 7.1 Select Yes to enable zone 1 in the controller.

Enable Zone 1 No Yes

7.2 Select the setup of the zone. Stand Alone Control only uses the sensors and components connected to the controller. Smatrix Base PRO uses a connected Uponor Smatrix Base PRO system.

Zone Setup Stand Alone Control Smatrix Base PRO

7.3 Select operation mode of the zone. The setting affects both zone 1 and 2, if the system is installed and setup accordingly.

This setting is only shown if 4 pipe is selected in the System Type menu. Z1&2 Operation Mode Only Heating Only Cooling Heating And Cooling

7.4 Select heating mode. Outdoor only uses an outdoor sensor, and Outdoor + Indoor comp. also uses a room sensor to calculate the supply temperature. The sensor/sensors are connected to either the Move PRO controller (Stand Alone Control) or to a connected Base PRO controller (Smatrix Base PRO).

See section 5.7 Connect sensors to controller > Outdoor sensor for more information Heating Mode

7.5 Select which indoor temperature data in the Smatrix Base PRO system to use when calculating the supply temperature.

CZ

• Worst Case uses the room temperature from the room (only rooms with a heating demand) with the highest setpoint value (heating mode), or with the highest measured relative humidity value (cooling), in the zone.

DE DK

• Average calculates,only in heating mode, the average from all connected room thermostats in the zone (selected in the Smatrix Base PRO interface I-147).

EE

ES

This setting is only shown if Smatrix Base PRO is selected in the Zone Setup menu, and if Outdoor + Indoor comp. is selected in Heating Mode.

FI

Smatrix Indoor Temperature Worst Case Average

FR 7.6 Select how to switch zone 1 and 2 between heating and cooling.

HR

• Indoor and Outdoor uses the indoor and outdoor temperatures to switch the zone between heating and cooling.

HU

• Supply Water Temp. uses the supply water temperature to switch the zone between heating and cooling.

IT

• Contact Input uses an external signal to switch the zone between heating and cooling.

LT

• Force Heating sets the zone in forced heating.

• Force Cooling sets the zone in forced cooling.

LV

This setting is only shown if 4 pipe is selected in the System Type menu, and if Z1&2 Operation Mode is set to Heating And Cooling.

NL

Outdoor Outdoor + Indoor comp.

Z1&2 HC Switchover Indoor and Outdoor Supply Water Temp. Contact Input Force Heating

NO PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

43


UK 7.7 Set minimum and maximum allowed supply temperature when in heating and/or cooling mode.

CZ

DE

DK

The heating minimum and maximum supply temperatures can only be set if heating is allowed in the zone. The cooling minimum and maximum supply temperatures can only be set if cooling is allowed in the zone. Heating Min. Supply Temp.

EE

15˚C min: 5

ES

max: 70

Heating Max. Supply Temp.

8. Enable Zone 2 8.1 Select Yes to enable zone 2 in the controller.

No Yes

8.2 Select the setup of the zone. Stand Alone Control only uses the sensors and components connected to the controller. Smatrix Base PRO uses a connected Uponor Smatrix Base PRO system. Domestic Hot Water (DHW) regulates the supply temperature for DHW in the zone.

min: 15

max: 70

Cooling Min. Supply Temp.

FR

8.0˚C min: 5.0

HR

max: 25.0

8.3 Select operation mode of the zone. The setting affects both zone 1 and 2, if the system is installed and setup accordingly.

Cooling Max. Supply Temp.

25.0˚C

HU

min: 8.0

max: 40.0

7.8 Select Enable to enable dehumidifier control in the zone.

IT

LT

LV

Note! Enabling dehumidifier disables circulation pump control in the zone (except for zones setup as Smatrix Base PRO where the circulation pump is controlled by the Base PRO controller). Dehumidifier Control Disable Enable

NL 7.9 Select Yes if a condensation sensor is installed in the zone and connected to the controller.

NO

Condensation Sensor No Yes

PL

Zone Setup Stand Alone Control Smatrix Base PRO Domestic Hot Water

70˚C

FI

Enable Zone 2

This setting is only shown if 4 pipe is selected in the System Type menu, zone 1 is not enabled, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO. Z1&2 Operation Mode Only Heating Only Cooling Heating And Cooling

8.4 Select heating mode. Outdoor only uses an outdoor sensor, and Outdoor + Indoor comp. also uses an room sensor to calculate the supply temperature. The sensor/sensors are connected to either the Move PRO controller (Stand Alone Control) or to a connected Base PRO controller (Smatrix Base PRO).

See section 5.7 Connect sensors to controller > Outdoor sensor for more information

This setting is not shown if Domestic Hot Water is selected in the Zone Setup menu.

Heating Mode Outdoor Outdoor + Indoor comp.

PT RO RU SE SK 44

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK 8.5 Select which indoor temperature data in the Smatrix Base PRO system to use when calculating the supply temperature. • Worst Case uses the room temperature from the room (only rooms with a heating demand) with the highest setpoint value (heating mode), or with the highest measured relative humidity value (cooling), in the zone. • Average calculates,only in heating mode, the average from all connected room thermostats in the zone (selected in the Smatrix Base PRO interface I-147).

This setting is only shown if Smatrix Base PRO is selected in the Zone Setup menu, and if Outdoor + Indoor comp. is selected in Heating Mode.

8.6 Select how to switch zone 1 and 2 between heating and cooling.

• Supply Water Temp. uses the supply water temperature to switch the zone between heating and cooling.

• Force Cooling sets the zone in forced cooling.

This setting is only shown if 4 pipe is selected in the System Type menu, zone 1 is not enabled, Zone Setup is set to Stand Alone Control or Smatrix Base PRO, and Z1&2 Operation Mode is set to Heating And Cooling. Z1&2 HC Switchover Indoor and Outdoor Supply Water Temp. Contact Input Force Heating

DE

The cooling minimum and maximum supply temperatures can only be set if cooling is allowed in the zone.

DK

Heating Min. Supply Temp.

EE

15˚C min: 5

max: 70

ES

Heating Max. Supply Temp.

70˚C min: 15

FI

max: 70

Cooling Min. Supply Temp.

FR

8.0˚C min: 5.0

max: 25.0

HR

Cooling Max. Supply Temp.

25.0˚C min: 8.0

HU

max: 40.0

8.7 Select Enable to enable dehumidifier control in the zone.

• Contact Input uses an external signal to switch the zone between heating and cooling. • Force Heating sets the zone in forced heating.

CZ

The heating minimum and maximum supply temperatures can only be set if heating is allowed in the zone.

• Indoor and Outdoor uses the indoor and outdoor temperatures to switch the zone between heating and cooling.

Smatrix Indoor Temperature Worst Case Average

8.7 Set minimum and maximum allowed supply temperature when in heating and/or cooling mode.

IT

Note! Enabling dehumidifier disables circulation pump control in the zone (except for zones setup as Smatrix Base PRO where the circulation pump is controlled by the Base PRO controller).

LT

Dehumidifier Control

LV

Disable Enable

NL 8.8 Select Yes if a condensation sensor is installed in the zone and connected to the controller.

NO

Condensation Sensor No Yes

PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

45


UK 9. Enable Zone 3 9.1 Select Yes to enable zone 3 in the controller.

CZ

Enable Zone 3 No Yes

DE

9.2 Select the setup of the zone. Stand Alone Control only uses the sensors and components connected to the controller. Smatrix Base PRO uses a connected Uponor Smatrix Base PRO system. Meltaway uses snow sensors to keep large areas clear of snow.

DK EE

ES

Zone Setup Stand Alone Control Smatrix Base PRO Meltaway

FI

9.3 Select operation mode of the zone. The setting affects zone 3, if the system is installed and setup accordingly.

FR

HR

This setting is only shown if 4 pipe is selected in the System Type menu and if Zone Setup is set to Stand Alone Control or Smatrix Base PRO. Z3 Operation Mode Only Heating Only Cooling Heating And Cooling

HU IT

9.4 Select heating mode. Outdoor only uses an outdoor sensor, and Outdoor + Indoor comp. also uses an room sensor to calculate the supply temperature. The sensor/sensors are connected to either the Move PRO controller (Stand Alone Control) or to a connected Base PRO controller (Smatrix Base PRO).

LT LV

See section 5.7 Connect sensors to controller > Outdoor sensor for more information

This setting is not shown if Meltaway is selected in the Zone Setup menu.

NL NO

Heating Mode Outdoor Outdoor + Indoor comp.

9.5 Select which indoor temperature data in the Smatrix Base PRO system to use when calculating the supply temperature. • Worst Case uses the room temperature from the room (only rooms with a heating demand) with the highest setpoint value (heating mode), or with the highest measured relative humidity value (cooling), in the zone. • Average calculates,only in heating mode, the average from all connected room thermostats in the zone (selected in the Smatrix Base PRO interface I-147).

This setting is only shown if Smatrix Base PRO is selected in the Zone Setup menu, and if Outdoor + Indoor comp. is selected in Heating Mode. Smatrix Indoor Temperature Worst Case Average

9.6 Select how to switch zone 3 between heating and cooling.

• Indoor and Outdoor uses the indoor and outdoor temperatures to switch the zone between heating and cooling.

• Supply Water Temp. uses the supply water temperature to switch the zone between heating and cooling.

• Contact Input uses an external signal to switch the zone between heating and cooling.

• Force Heating sets the zone in forced heating.

• Force Cooling sets the zone in forced cooling.

This setting is only shown if Z3 Operation Mode is set to Heating And Cooling, and if the zone is setup as Stand Alone Controller or Smatrix Base PRO.

HC Switchover Indoor and Outdoor Supply Water Temp. Contact Input Force Heating

PL PT RO RU SE SK 46

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK 9.7 Set minimum and maximum allowed supply temperature when in heating and/or cooling mode.

The cooling minimum and maximum supply temperatures can only be set if cooling is allowed in the zone. Heating Min. Supply Temp.

min: 5

max: 70

70˚C Cooling Min. Supply Temp.

min: 5.0

max: 25.0

Cooling Max. Supply Temp.

• Indoor and Outdoor uses the indoor and outdoor temperatures to switch the zones between heating and cooling.

EE

FI

• Force Heating sets the zones in forced heating.

FR

• Force Cooling sets the zone in forced cooling. HC Switchover

HR

Indoor and Outdoor Supply Water Temp. Contact Input Force Heating

HU

11. Assign Controller to zone

If the Move PRO controller is connected to a Smatrix Base PRO system, the connected controllers can be assigned to the different zones. This requires the zone setup to be set to Smatrix Base PRO.

IT LT

N OT E ! The controllers in the Base PRO system must be registered to the Smatrix Base PRO interface I-147. Otherwise they will not appear in this menu.

Dehumidifier Control Disable Enable

9.9 Select Yes if a condensation sensor is installed in the zone and connected to the controller.

This setting is only shown if Smatrix Base PRO is selected in the Zone Setup menu.

Select a connected Smatrix Base PRO controller and assign it to a zone.

No Yes

DK

• Contact Input uses an external signal to switch the zones between heating and cooling.

Note! Enabling dehumidifier disables circulation pump control in the zone (except for zones setup as Smatrix Base PRO where the circulation pump is controlled by the Base PRO controller).

Condensation Sensor

DE

max: 40.0

9.8 Select Enable to enable dehumidifier control in the zone.

CZ

ES

25.0˚C min: 8.0

Select how to switch the zones in a 2 pipe system between heating and cooling (requires Indoor Cooling Only to be set to No). This only affects zones set to Stand Alone Control. If one of the zones is set to Smatrix Base PRO this setting will not be shown, as the heating/cooling swtiching will be performed by the Base PRO system.

• Supply Water Temp. uses the supply water temperature to switch the zones between heating and cooling.

max: 70

8.0˚C

Heating Max. Supply Temp.

min: 15

The heating minimum and maximum supply temperatures can only be set if heating is allowed in the zone.

15˚C

10 HC Switchover

LV NL NO

Assign Controller to zone Controller 1 Controller 2

PL

Zone 1 > Zone 2 >

PT

Controller 1 Not Assigned Zone 1 Zone 2 Zone 3

RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

47


UK CZ DE

5.18 Pre heating concrete slab (DIN 1264-4)

3. Set the date

The controller can be setup to pre heat a concrete slab before a property is finished.

Set the date of the system, starting with the day. Date Enter the day

Tue 01.06.2016

Pre heating is run in three different phases.

DK

Pase 1: The supply temperature setpoint is set to 25 ˚C for 3 days (can be set in the Settings menu).

Pase 2: The supply temperature setpoint is set to maximum allowed calculated setpoint for 4 days (can be set in the Settings menu).

Pase 3: The controller enters Standby mode until the startup wizard is restarted (Settings > Installer Settings > Restart wizard). Frost protection is active during this final phase.

EE ES FI FR

Enter the month

Tue 01.06.2016

In order to setup the controller zones, after pre heating, the startup wizard must be restarted.

Select Pre Heating to enable pre heating operation mode in the controller.

Select the language which is to be used in the controllers menu system. Language

LV

5. Enable Pre Heating Zone 1 5.1 Select Enable to enable pre heating zone 1 in the controller.

Pre-Heating Zone 1 Disable Enable

Set the time of the system, starting with the hours. 5.2 Set a maximum allowed calculated supply setpoint.

Time Enter the hours

12:34

NL

hh:mm

Operation Mode Standard Pre Heating

2. Set the time

LT

Enter the year

4. Select Operation Mode

English Deutsch Espanol Swedish

IT

Date

Tue 01.06.2016

1. Set language

HU

Date

C aution !

To setup the controller for pre heating:

HR

Z1 Max. Calc. Supply Setpoint

45.0˚C min: 5.0

Time

max: 70.0

Enter the minutes

NO

12:34 hh:mm

PL PT RO RU SE SK 48

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK 6. Enable Pre Heating Zone 2 6.1 Select Enable to enable pre heating zone 2 in the controller.

CZ

Pre-Heating Zone 2

DE

Disable Enable

DK

6.2 Set a maximum allowed calculated supply setpoint.

Z2 Max. Calc. Supply Setpoint

EE

45.0˚C min: 5.0

max: 70.0

ES

7. Enable Pre Heating Zone 3 7.1 Select Enable to enable pre heating zone 3 in the controller.

FI

Pre-Heating Zone 3 Disable Enable

FR HR

7.2 Set a maximum allowed calculated supply setpoint.

Z3 Max. Calc. Supply Setpoint

45.0˚C min: 5.0

HU

max: 70.0

IT LT LV NL NO PL PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

49


UK

6

CZ

Finishing installation

DE Make a complete check up of the installation:

5 DK

1. Make sure all wiring is done correctly and that the wires are thoroughly fastened.

3 1

EE

2

N

L

74 71

ES

S BMdbus

Mo

21

22

23

24

25

26

27

28

29

72

75

3. Check the mixing valves.

T

125 N 79 77

2. Re-attach the terminal covers to the controller.

mA

L

80

78

76

73

30

Increase the setpoints in each zone to make sure the mixing valves are opening correctly.

D microS

5 RJ4

4. Check the diverting valves.

FI

Base PRO

2 FR

6

4

Go to Settings > Zone # Settings (# = 1 – 3) > Manual Operation > Mixing valve and make sure the diverting valves are operating correctly.

5. Set system parameters in the controller to the defined operating settings. 6. Print and fill in the “Installation report” located at the end of the manual.

HR

7. Give the manual and all information about the system to the user.

HU IT

7

LT LV NL NO PL PT RO RU SE SK 50

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK

7 Operate the Uponor Smatrix Move PRO ­controller

CZ DE

7.1 Principle of operation

7.2 Controller layout

The controller calculates the supply temperature for up to 3 different zones using a wide array of sensors. The calculated supply temperature is compared to the measured supply temperature. If the measured temperature differs from the calculated, the controller adjusts the mixing valve to raise or lower the supply temperature in the zone.

The illustration below shows parts of the controller.

A

C

DK

B EE ES

H eating / cooling The zones (if set to Stand Alone Control and heating/ cooling enabled) can switch between heating and cooling using one of the following functions (set in the startup wizard): • Indoor and Outdoor uses the indoor and outdoor temperatures to switch the zones between heating and cooling. • Supply Water Temp. uses the supply water temperature to switch the zones between heating and cooling.

FI

D FR Item

Description

A

Display

B

Navigation wheel/ OK button Used for navigating the menu system, selecting options and confirming selections.

C

• Force Cooling sets the zone in forced cooling. If one of the zones is set to Smatrix Base PRO the Base PRO system will perform the heating/ cooling swtiching. The optional room temperature sensor is placed in a reference area and enables an indoor temperature setpoint parameter. It is used to keep fluctuations in the indoor temperature close to a minimum and as close as possible to the indoor temperature setpoint. In cooling mode it is also used for dew point calculation.

HU

Information button Used for showing current zone information such as supply temperature, pump status etc.

• Contact Input uses an external signal to switch the zones between heating and cooling. • Force Heating sets the zones in forced heating.

HR

IT

Push the button repeatedly to switch zones. D

Back button

LT

7.3 Navigating the menu system S elect / change

LV

Turn the control wheel to select an option, or to change a parameter setting.

NL NO PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

51


UK CZ

C onfirm

S tand A lone C ontrol

Press the control wheel to confirm a selection or parameter setting.

The following information is shown if the zone is setup as Stand Alone Control. • Supply Temperature (current supply temperature)

DE

• Indoor Temperature (current indoor temperature in the reference room requires a room temperature sensor).

DK

If System Type is set to 4 Pipe, and Operation Mode for the zone is set to Only Heating, then Heating Mode for the zone must be set to Outdoor + Indoor comp. to show this information.

EE

• Outdoor Temperature (current outdoor temperature)

ES

7.4 Start up

FI

When starting up, the controller shows the Uponor logo before entering the main menu.

FR

N OT E ! The display on the controller may start flashing when powered on. This only occurs after a firmware update and regular operation will continue shortly after.

HR HU

7.5 Information button

IT

• Pump (status). This information is not shown if a dehumidifier is enabled in the zone. • Mixing valve (status)

S matrix B ase PRO The following information is shown if the zone is setup as Smatrix Base PRO. • Supply Temperature (current supply temperature) • Indoor Temperature (current indoor temperature, worst case or average temperature from integrated Smatrix Base PRO system is used). This information is only shown when there is a heating/cooling demand in the Smatrix Base PRO system. If System Type is set to 4 Pipe, and Operation Mode for the zone is set to Only Heating, then Heating Mode for the zone must be set to Outdoor + Indoor comp. to show this information.

LT

• Outdoor Temperature (current outdoor temperature)

LV

• Mixing valve (status)

D omestic H ot W ater

NL The information button can be pressed anytime to get instant access to a summary of current information in the zones. Press the button several times to toggle between the different zones. Press the back button to return to the menu system.

NO PL

The following information is shown if the zone is setup as Domestic Hot Water. • Supply Temperature (current supply temperature) • Return Temperature (current return temperature) • Pump (status) • Mixing valve (status)

PT RO RU SE SK 52

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK

7.7 System Overview

M eltaway The following information is shown if the zone is setup as Meltaway.

This menu shows the current outdoor temperature, and supply temperatures for enabled zones.

CZ

Z# - S upply T emperature

DE

• Supply Temperature (current supply temperature) • Outdoor Temperature (current outdoor temperature) • Status (current meltaway statu:, Stop, Idle, Melting, Protection) • Pump (status)

The current supply temperature is shown. The temperature is measured by the supply temperature sensor wired to the controller.

DK

O utdoor T emperature

• Mixing valve (status)

7.6 Main menu The main menu is the base of the menu system, giving access to 4 different menu alternatives. Use the navigation wheel to navigate the menus and parameter settings. System Overview Z1 - Supply Temperature

35.5 °C

Z2 - Supply Temperature

30.1 °C

Z3 - Supply Temperature

18.9 °C

Outdoor Temperature

27.4 °C

The current outdoor temperature is shown. The temperature is measured by an outdoor temperature sensor wired to either the controller or to a connected Smatrix Base PRO system.

EE ES

7.8 Information FI

This menu shows information about the system, enabled zones and the controller (when the operating mode is set to Standard in the startup wizard).

FR

Menu tree*

HR

Information System information

Icon

Zone 1 Information

Description

Zone 3 Information

- Current outdoor temperature, and supply temperatures for enabled zones are shown.

Controller Information

Information

*

- System, zone (enabled zones only) and controller information are shown in this menu.

S ystem

Alarms

The system information menu shows the current time and date.

- Active alarms and alarm history are shown in this menu. Acknowledge alarms and/or reset alarm history. Settings - System, zone (enabled zones only) and controller parameters can be set in this menu.

HU

Zone 2 Information

System Overview

IT

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

LT

information

LV

If Operating Mode is set to Standard the measured outdoor temperature (from either the controller of from a connected Smatrix Base PRO system, see section 5.7 Connect sensors to controller > Outdoor sensor for more information) is also shown.

NL NO PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

53


UK Z one 1 I nformation

Operating Mode

This menu shows information about zone 1.

CZ

Menu tree*

DE

Supply temperature

Zone 1 Information Zone Setup Heating Mode

DK

Operating Mode Supply temperature Indoor temperature

EE

Mixing Valve Pump

ES

Heating Cooling

FI

*

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

Zone Setup

FR

The selected zone setup is shown: • Stand Alone Control

HR

• Smatrix Base PRO (integrated with a Smatrix Base PRO system)

HU

The current operating mode (heating or cooling) for the zone is shown:

Heating Mode The selected heating mode for the zone is shown:

IT

• Outdoor (only the outdoor temperature sensor is used)

LT

• Outdoor + Indoor comp. (the outdoor temperature sensor is used together with room temperature data)

LV

This information is only shown if one of the following conditions is met:

NL

• System Type is set to 4 Pipe, and Z1&2 Operation Mode is set to Only Heating or Heating and Cooling.

NO

• System Type is set to 2 Pipe, and Indoor Cooling Only is set to No.

The current supply temperature is shown. The temperature is measured by the supply temperature sensor wired to the controller. Indoor temperature The current indoor temperature for the zone is shown. If the zone is setup as Stand Alone Control the temperature is measured by a room temperature sensor wired to the Move PRO controller. This information is always shown, except if System Type is set to 4 Pipe, Z1&2 Operation Mode is set to Only Heating, and Heating Mode is set to Outdoor. If the zone is setup as Smatrix Base PRO the Base PRO controller sends either Average or Worst Case (setup in the startup wizard) temperatures from the Base PRO system. This information is shown when there is a heating/cooling demand in the zone, except if System Type is set to 4 Pipe, Z1&2 Operation Mode is set to Only Heating, and Heating Mode is set to Outdoor. Mixing Valve The status of the mixing valve is shown. 0 % (supply from heat source closed) – 100 % (supply from heat or cooling source fully opened). Pump The status of the circulation pump is shown (on/off). This information is only shown if Zone Setup is set to Stand Alone Control, and if Dehumidifier Control is Disabled.

PL PT RO RU SE SK 54

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Heating

MENU TREE*

This menu shows current heating mode information in the zone.

CZ

Cooling Cooling Curve

This information is only shown if one of the following conditions is met:

Calculated Supply Setpoint

• System Type is set to 4 Pipe, and Z1&2 Operation Mode is set to Only Heating or Heating and Cooling.

Relative Humidity

• System Type is set to 2 Pipe, and Indoor Cooling Only is set to No.

Dew Point Temperature

DK

Dehumidifier *

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

EE

COOLING CURVE

MENU TREE*

This menu shows the cooling curve, and max/min supply temperature limits, for the zone.

Heating Heating Curve Calculated Supply Setpoint ECO-Comf Status *

DE

Condensation

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

ES

CALCULATED SUPPLY SETPOINT

FI

The calculated supply temperature for cooling is shown. CONDENSATION

FR

HEATING CURVE

The current condensation status (Yes/No) in the zone is shown.

This menu shows the heating curve, and max/min supply temperature limits, for the zone.

This menu is only shown if Condensation Sensor is enabled in the startup wizard for the zone.

HR

CALCULATED SUPPLY SETPOINT

RELATIVE HUMIDITY

HU

The calculated supply temperature is shown. The setpoint is calculated using the sensor setup selected in Heating Mode.

The relative humidity level in the zone is shown.

ECO-COMF STATUS The current ECO/Comfort status for the zone is shown. This information is only shown if Zone Setup is set to Stand Alone Control and Heating Mode is set to Outdoor + Indoor comp..

If the zone is setup as Stand Alone Control the relative humidity is measured by a relative humidity sensor wired to the Move PRO controller.

IT

If the zone is setup as Smatrix Base PRO the Base PRO controller sends the highest relative humidity level from the Base PRO system (measured at thermostats with RH sensors and an active cooling demand).

LT LV

DEW POINT TEMPERATURE Cooling This menu shows current cooling mode information in the zone. This information is only shown if one of the following conditions is met: • System Type is set to 4 Pipe, and Z1&2 Operation Mode is set to Only Cooling or Heating and Cooling.

NL

The current dew point temperature in the zone is shown. DEHUMIDIFIER

NO

The status of the dehumidifier in the zone is shown (on/off).

PL

This information is only shown if Dehumidifier Control is Enabled.

PT

• System Type is set to 2 Pipe.

RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

55


UK Z one 2 I nformation

Operating Mode

This menu shows information about zone 2.

CZ

Menu tree*

DE

Supply temperature

Zone 2 Information Zone Setup Heating Mode

DK

Operating Mode Supply temperature Indoor temperature

EE

DHW Circ. Return Temp Mixing Valve

ES

Pump Heating Cooling

FI *

FR

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

Zone Setup The selected zone setup is shown:

HR

• Stand Alone Control • Smatrix Base PRO (integrated with a Smatrix Base PRO system)

HU

• Domestic Hot Water (DHW)

IT

Heating Mode The selected heating mode for the zone is shown: • Outdoor (only the outdoor temperature sensor is used)

LT

• Outdoor + Indoor comp. (the outdoor temperature sensor is used together with room temperature data)

LV

This information is only shown if one of the following conditions is met:

NL

• System Type is set to 4 Pipe, Z1&2 Operation Mode is set to Only Heating or Heating and Cooling, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO.

NO PL

• System Type is set to 2 Pipe, Indoor Cooling Only is set to No, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO.

PT

The current operating mode (heating or cooling) for the zone is shown:

The current supply temperature is shown. The temperature is measured by the supply temperature sensor wired to the controller. Indoor temperature The current indoor temperature for the zone is shown. If the zone is setup as Stand Alone Control the temperature is measured by a room temperature sensor wired to the Move PRO controller. This information is always shown, except if System Type is set to 4 Pipe, Z1&2 Operation Mode is set to Only Heating, and Heating Mode is set to Outdoor. If the zone is setup as Smatrix Base PRO the Base PRO controller sends either Average or Worst Case (setup in the startup wizard) temperatures from the Base PRO system. This information is shown when there is a heating/cooling demand in the zone, except if System Type is set to 4 Pipe, Z1&2 Operation Mode is set to Only Heating, and Heating Mode is set to Outdoor. DHW Circ. Return Temp The current return temperature is shown. This information is only shown if Zone Setup is set to Domestic Hot Water. Mixing Valve The status of the mixing valve is shown. 0 % (supply from heat source closed) – 100 % (supply from heat or cooling source fully opened). Pump The status of the circulation pump is shown (on/off). This information is only shown if Zone Setup is set to Stand Alone Control or Domestic Hot Water, and if Dehumidifier Control is Disabled.

RO RU SE SK 56

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Heating

MENU TREE*

This menu shows current heating mode information in the zone.

CZ

Cooling Cooling Curve

This information is only shown if one of the following conditions is met:

Calculated Supply Setpoint

• System Type is set to 4 Pipe, and Z1&2 Operation Mode is set to Only Heating or Heating and Cooling.

Relative Humidity

• System Type is set to 2 Pipe, and Indoor Cooling Only is set to No.

Dew Point Temperature

DK

Dehumidifier *

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

EE

COOLING CURVE

MENU TREE*

This menu shows the cooling curve, and max/min supply temperature limits, for the zone.

Heating Heating Curve Calculated Supply Setpoint ECO-Comf Status *

DE

Condensation

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

ES

CALCULATED SUPPLY SETPOINT

FI

The calculated supply temperature for cooling is shown. CONDENSATION

FR

HEATING CURVE

The current condensation status (Yes/No) in the zone is shown.

This menu shows the heating curve, and max/min supply temperature limits, for the zone.

This menu is only shown if Condensation Sensor is enabled in the startup wizard for the zone.

HR

CALCULATED SUPPLY SETPOINT

RELATIVE HUMIDITY

HU

The calculated supply temperature is shown. The setpoint is calculated using the sensor setup selected in Heating Mode.

The relative humidity level in the zone is shown.

ECO-COMF STATUS The current ECO/Comfort status for the zone is shown. This information is only shown if Zone Setup is set to Stand Alone Control and Heating Mode is set to Outdoor + Indoor comp..

If the zone is setup as Stand Alone Control the relative humidity is measured by a relative humidity sensor wired to the Move PRO controller.

IT

If the zone is setup as Smatrix Base PRO the Base PRO controller sends the highest relative humidity level from the Base PRO system (measured at thermostats with RH sensors and an active cooling demand).

LT LV

DEW POINT TEMPERATURE Cooling This menu shows current cooling mode information in the zone. This information is only shown if one of the following conditions is met: • System Type is set to 4 Pipe, and Z1&2 Operation Mode is set to Only Cooling or Heating and Cooling.

NL

The current dew point temperature in the zone is shown. DEHUMIDIFIER

NO

The status of the dehumidifier in the zone is shown (on/off).

PL

This information is only shown if Dehumidifier Control is Enabled.

PT

• System Type is set to 2 Pipe.

RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

57


UK Z one 3 I nformation

Operating Mode

This menu shows information about zone 3.

CZ

Menu tree*

DE

Supply temperature

Zone 3 Information Zone Setup Heating Mode

DK

Operating Mode Supply temperature Indoor temperature

EE

Calculated Supply Setpoint Indoor temperature

ES

Meltaway Curve Return temperature

FI

Heating Cooling Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

Zone Setup

IT

The selected zone setup is shown: • Stand Alone Control

LT

• Smatrix Base PRO (integrated with a Smatrix Base PRO system)

LV NL

If the zone is setup as Stand Alone Control the temperature is measured by a room temperature sensor wired to the Move PRO controller. This information is always shown, except if System Type is set to 4 Pipe, Z3 Operation Mode is set to Only Heating, and Heating Mode is set to Outdoor. If the zone is setup as Smatrix Base PRO the Base PRO controller sends either Average or Worst Case (setup in the startup wizard) temperatures from the Base PRO system. This information is shown when there is a heating/cooling demand in the zone, except if System Type is set to 4 Pipe, Z3 Operation Mode is set to Only Heating, and Heating Mode is set to Outdoor.

• Meltaway

Meltaway Curve

Heating Mode

This menu shows the meltaway curve, and max/min supply temperature limits, for the zone.

The selected heating mode for the zone is shown:

NO

• Outdoor (only the outdoor temperature sensor is used)

PL

• Outdoor + Indoor comp. (the outdoor temperature sensor is used together with room temperature data)

PT

This information is only shown if one of the following conditions is met:

RO

• System Type is set to 4 Pipe, Z3 Operation Mode is set to Only Heating or Heating and Cooling, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO.

RU

This information is only shown if Zone Setup is set to Meltaway.

The current indoor temperature for the zone is shown.

Pump

*

The calculated supply temperature for meltaway is shown.

Indoor temperature

Mixing Valve

HU

Calculated Supply Setpoint

Ground Moisture Status

HR

The current supply temperature is shown. The temperature is measured by the supply temperature sensor wired to the controller.

Ground Temperature Primary Return Temperature

FR

The current operating mode (heating or cooling) for the zone is shown:

This information is only shown if Zone Setup is set to Meltaway. Return temperature The current return temperature is shown. This information is only shown if Zone Setup is set to Meltaway.

• System Type is set to 2 Pipe, Indoor Cooling Only is set to No, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO.

SE SK 58

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Ground Temperature

Pump

The current temperature in the ground around the snow sensor is shown.

The status of the circulation pump is shown (on/off).

CZ

This information is only shown if Zone Setup is set to Meltaway.

This information is only shown if Zone Setup is set to Stand Alone Control or Meltaway, and if Dehumidifier Control is Disabled.

DE

Ground Moisture

Heating

This parameter shows if there is moisture around the snow sensor.

This menu shows current heating mode information in the zone.

This information is only shown if Zone Setup is set to Meltaway.

This information is only shown if one of the following conditions is met:

DK EE

The current primary return temperature is shown.

• System Type is set to 4 Pipe, and Z3 Operation Mode is set to Only Heating or Heating and Cooling.

This information is only shown if Zone Setup is set to Meltaway.

• System Type is set to 2 Pipe, and Indoor Cooling Only is set to No.

FI

Status

MENU TREE*

FR

Primary Return temperature

This parameter shows the current meltaway status.

Heating

Stop: Meltaway is inactive.

Heating Curve

Idle: Meltaway is idle and the supply temperature is kept low to keep the zone from getting too cold.

Calculated Supply Setpoint

Melting: M  eltaway is active. Protection: Protecting the heat source from low return temperatures. The status may change, in case of sensor fault. An alarm will also be shown in the display if that is the case. This information is only shown if Zone Setup is set to Meltaway. Mixing Valve The status of the mixing valve is shown. 0 % (supply from heat source closed) – 100 % (supply from heat or cooling source fully opened).

ES

HR

ECO-Comf Status *

HU

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

HEATING CURVE

IT

This menu shows the heating curve, and max/min supply temperature limits, for the zone.

LT

CALCULATED SUPPLY SETPOINT The calculated supply temperature is shown. The setpoint is calculated using the sensor setup selected in Heating Mode.

LV

ECO-COMF STATUS

NL

The current ECO/Comfort status for the zone is shown. This information is only shown if Zone Setup is set to Stand Alone Control and Heating Mode is set to Outdoor + Indoor comp..

NO PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

59


UK Cooling

DEW POINT TEMPERATURE

CZ

This menu shows current cooling mode information in the zone.

The current dew point temperature in the zone is shown.

DE

This information is only shown if one of the following conditions is met:

DEHUMIDIFIER

DK

• System Type is set to 4 Pipe, and Z3 Operation Mode is set to Only Cooling or Heating and Cooling.

The status of the dehumidifier in the zone is shown (on/off). This information is only shown if Dehumidifier Control is Enabled.

• System Type is set to 2 Pipe.

EE

C ontroller I nformation MENU TREE*

This menu shows information about the controller.

Cooling

ES

Menu tree Cooling Curve Calculated Supply Setpoint

FI

Controller Information Language

Condensation

About...

Relative Humidity Dew Point Temperature

FR

Dehumidifier *

HR HU

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

Language This menu show the set display language for the controller.

COOLING CURVE

About...

This menu shows the cooling curve, and max/min supply temperature limits, for the zone.

This menu shows the serial number, software versions, and hardware versions of the controller.

CALCULATED SUPPLY SETPOINT

IT

The calculated supply temperature for cooling is shown. CONDENSATION

LT

The current condensation status (Yes/No) in the zone is shown.

LV

This menu is only shown if Condensation Sensor is enabled in the startup wizard for the zone. RELATIVE HUMIDITY

NL

The relative humidity level in the zone is shown. If the zone is setup as Stand Alone Control the relative humidity is measured by a relative humidity sensor wired to the Move PRO controller.

NO

If the zone is setup as Smatrix Base PRO the Base PRO controller sends the highest relative humidity level from the Base PRO system (measured at thermostats with RH sensors and an active cooling demand).

PL PT RO RU SE SK 60

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK

7.9 Alarms

A larm

This menu shows the current active alarms and the alarm history. A possibility of acknowleding all alarms and reseting the alarm histroy is also available. Active alarms are always indicated with a ! and an number (of alarms) in the upper right corner of the display. Acknowledge the active alarms to remove the alarm indicator. Menu tree Alarms Active alarms Alarm history Acknowledge all alarms Reset alarm history

A ctive

alarms

This menu shows a list of all active alarms in the controller. Each active alarm is presented with a short description about when it was logged, why it occured, and if it has been acknowledged (indicated with a !). Detailed information is available via button press. The detailed information shows alarm type, time and date when it was logged, the source of the alarm with severity (PR1 to PR5, where PR5 is the worst), and which alarm group it belongs to (1 to 10). The alarm can alse be acknowledged in the detailed information. To access detailed alarm information: 1. Select an alarm. 2. Press the navigation wheel to confirm selection.

history

This menu shows a list of the 10 latest alarms in the controller. Each active alarm is presented with a short description about when it was logged and why it occured. Detailed information is available via button press.

CZ DE

The detailed information shows alarm type, time and date when it was logged, the source of the alarm with severity (PR1 to PR5, where PR5 is the worst), and which alarm group it belongs to (1 to 10).

DK

To access detailed alarm information:

EE

1. Select an alarm.

ES

2. Press the navigation wheel to confirm selection.

A cknowledge

all alarms

FI

This menu enables to acknowledge all active alarms. To acknowledge all active alarms:

FR

1. Select Acknowledge all alarms. 2. Press the navigation wheel to confirm selection.

HR

3. Select Yes.

Setting range: No (default)/Yes

4. Press the navigation wheel to confirm selection.

R eset

HU

alarm history

This menu enables to reset the alarm history.

IT

To reset the alarms history: 1. Select Reset alarm history.

LT

2. Press the navigation wheel to confirm selection. 3. Select Yes.

LV

Setting range: No (default)/Yes

4. Press the navigation wheel to confirm selection.

NL NO PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

61


UK CZ DE

7.10 Settings

T Outdoor Fallback

In this menu installer settings, enabled zone settings, and controller settings can be changed (when the operating mode is set to Standard in the startup wizard).

In this menu the fallback temperature for the outdoor temperature sensor is set. This value will be used if the connection to the outdoor temperature sensor is lost.

Menu tree*

To set the fallback temperature for the outdoor temperature sensor: 1. Select T Outdoor Fallback.

DK

Settings Installer Settings

EE ES

Zone 1 Settings

3. Set the value.

Zone 2 Settings

Default: 0 ˚C

Zone 3 Settings

Setting range: -50 – 50 ˚C, 1 ˚C increments

HC Switchover

4. Confirm the new setting by pressing the navigation wheel again.

Controller Settings *

FI

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

I nstaller S ettings In this menu lock codes (to gain access to locked parameter settings) can be set or changed, factory settings can be restored, backup of controller parameter settings can be managed, or the setup wizard can be restarted.

FR HR

Menu tree

HU

LT

A lock code can be used to block a user from changing parameter settings. The menu system is fully accessible, but the lock code is required to enter and change parameter settings. The default lock code is 0000. It is recommended to change this code if using this function.

T Outdoor Fallback

To enable lock code in the controller:

Lock code

1. Select Lock code.

Change lock code

2. Press the navigation wheel to confirm selection.

Display settings Restore factory settings Restore backup

LV

Lock code

The controller locks itself when it has been left untouched for about 10 minutes.

Installer Settings

IT

2. Press the navigation wheel to confirm selection.

3. Select Enable. 4. Press the navigation wheel to confirm selection.

New backup Restart wizard

NL NO PL PT RO RU SE SK 62

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK ENTERING A MENU WHEN LOCK CODE IS ENABLED

Display settings

To enter a lock code:

This menu enables display settings, such as contrast, and it also shows the version number of the display software.

CZ

To set the display contrast:

DE

1. Select the parameter. 2. Press the navigation wheel to confirm selection. 3. Enter the lock code in the boxes using the navigation wheel.

Turn the navigation wheel to either select a box, or to increase/decrease a value in edit mode.

Press the navigation wheel to enter edit mode or to confirm the new setting.

Default: 0000

1. Select Display settings.

3. Select Display contrast.

5. Set the display contrast.

Setting range: -50 – 100 %, 1 % increments

6. Press the navigation wheel to confirm selection.

5. Change the parameter setting and exit.

Restore factory settings

Change lock code

This menu enables all parameter settings in the controller to be reset to the factory default settings.

This menu is only shown when Lock code has been enabled in the Lock code menu. N OT E ! If the controller display is already locked, it has to be unlocked before entering the new lock code. To change the lock code:

EE

4. Press the navigation wheel to confirm selection.

4. Confirm the lock code by pressing and holding the navigation wheel for a number of seconds.

The standard lock code which is used to block a user from changing parameter settings, can be changed in this menu.

DK

2. Press the navigation wheel to confirm selection.

ES FI FR

To restore the factory settings: 1. Select Restore factory settings.

HR

2. Press the navigation wheel to confirm selection. 3. Select Yes.

HU

Setting range: No (default)/Yes

4. Press the navigation wheel to confirm selection.

IT

5. All parameters in the controller are being restored to factory settings.

LT

1. Select Change lock code. 2. Press the navigation wheel to confirm selection.

LV

3. Enter the new lock code in the boxes using the navigation wheel.

Turn the navigation wheel to either select a box, or to increase/decrease a value in edit mode.

NL

Press the navigation wheel to enter edit mode or to confirm the new setting.

NO

Default: 0000

PL

4. Confirm the new lock code by pressing and holding the navigation wheel for about 8 seconds.

PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

63


UK Restore backup

CZ

This menu enables the controller to restore all parameter settings from a previously created backup located on the microSD-card.

DE

To restore from a backup: 1. Make sure the microSD-card with the backup is inserted into the controller.

DK EE

Z one 1 S ettings In this menu parameter settings for zone 1 can be set or changed. Menu tree* Zone 1 Settings Supply Temp. Settings

2. Select Restore backup.

Heating Indoor Temp. Settings

3. Press the navigation wheel to confirm selection.

Comf. - ECO Heating Curve

4. Select Yes.

ES

Cooling Curve

Setting range: No (default)/Yes

Manual Operation

5. Press the navigation wheel to confirm selection.

Pump

6. All parameters in the controller are being restored from backup.

FI

Mixing Valve Dehumidifier Control Seasonal Shut Off

New backup

FR

This menu enables the controller to save a backup of all parameter settings to the microSD-card.

HR

H/C Switchover Condensation Delay *

To save from a backup: 1. Make sure a microSD-card, where the backup is to be saved, into the controller.

HU IT

Supply Temp. Settings

2. Select New backup.

This menu enables access to settings related to the supply temperature in the zone.

3. Press the navigation wheel to confirm selection.

MENU TREE*

4. Select Yes.

LT

Supply Temp. Settings Heating

Setting range: No (default)/Yes

Cooling

5. Press the navigation wheel to confirm selection. 6. All parameters in the controller are being saved to the microSD card.

LV

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

*

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

Restart wizard

NL

This menu enables the controller to restart the setup wizard.

NO

To restart the setup wizard: 1. Select Restart wizard.

PL

2. Press the navigation wheel to confirm selection. 3. Select Yes.

PT

Setting range: No (default)/Yes

4. Press the navigation wheel to confirm selection. 5. The setup wizard is now being restarted.

RO RU SE SK 64

U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK HEATING

H E AT I N G M A X . S U P P LY T E M P.

This menu enables access to settings related to the heating supply temperature in the zone.

In this menu the maximum allowed supply temperature for the zone can be set. The supply temperature is not allowed to rise above this value.

CZ

This menu is only shown if one of the following requirements are met:

To set the maximum allowed supply temperature:

DE

• System Type is set to 2 Pipe and Indoor Cooling Only is set to No. • System Type is set to 4 Pipe and Z1&2 Operation Mode is set to Only Heating or Heating And Cooling.

1. Select Heating Max. supply temp. 2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 70.0 ˚C

Setting range: 5.0 (or min. supply temp) – 70.0 ˚C, 0.1 ˚C increments

MENU TREE

Heating Calculated Supply Setpoint

D E V I AT I O N A L A R M L I M I T

Heating Max. Supply Temp.

In this menu the deviation alarm limit for the supply temperature in the zone is set. If the difference between the measured and the calculated supply temperatures are higher than the set limit during the time set in Deviation alarm delay, the alarm is triggered.

Deviation alarm delay C A L C U L AT E D S U P P LY S E T P O I N T

In this menu the calculated supply setpoint for the zone can be overidden. This temperature is used as setpoint for the supply temperature.

To set the deviation alarm limit:

To override the calculated supply setpoint:

2. Press the navigation wheel to confirm selection.

1. Select Calculated supply setpoint.

3. Set the value.

2. Press the navigation wheel to confirm selection. 3. Select Manual. 4. Set the override value.

Setting range: -5.0 – 70.0 ˚C, 0.1 ˚C increments

5. Confirm the new setting by pressing the navigation wheel again. H E AT I N G M I N . S U P P LY T E M P.

In this menu the minimum allowed supply temperature for the zone can be set. The supply temperature is not allowed to fall below this value.

EE ES

4. Confirm the new setting by pressing the navigation wheel again.

Heating Min. Supply Temp. Deviation alarm limit

DK

FI FR HR

1. Select Deviation alarm limit.

Default: 10.0 ˚C

Setting range: 0.0 – 50.0 ˚C, 0.1 ˚C increments

HU IT

4. Confirm the new setting by pressing the navigation wheel again.

LT

D E V I AT I O N A L A R M D E L AY

In this menu the deviation alarm delay for the deviation alarm limit in the zone is set. If the difference between the measured and the calculated supply temperatures are higher than Deviation alarm limit during the set delay, the alarm is triggered.

LV

To set the deviation alarm delay:

NO

To set the minimum allowed supply temperature:

1. Select Deviation alarm delay.

1. Select Heating Min. supply temp.

2. Press the navigation wheel to confirm selection.

2. Press the navigation wheel to confirm selection.

3. Set the value.

3. Set the value.

Default: 5 min

Default: 15.0 ˚C

Setting range: 0 – 30 min, 1 min increments

Setting range: 5.0 – 35.0 ˚C (or max. supply temp), 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again.

NL

PL PT RO

4. Confirm the new setting by pressing the navigation wheel again.

RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

65


UK COOLING

C O O L I N G M I N . S U P P LY T E M P.

CZ

This menu enables access to settings related to the cooling supply temperature in the zone.

In this menu the minimum allowed supply temperature for the zone can be set. The supply temperature is not allowed to fall below this value.

DE

This menu is only shown if one of the following requirements are met:

To set the minimum allowed supply temperature:

• System Type is set to 2 Pipe.

DK

• System Type is set to 4 Pipe and Z1&2 Operation Mode is set to Only Cooling or Heating And Cooling.

EE

MENU TREE

1. Select Cooling Min. supply temp. 2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 8.0 ˚C

Setting range: 5.0 – 40.0 ˚C (or max. supply temp), 0.1 ˚C increments

Cooling

ES

Calculated Supply Setpoint Cooling Min. Supply Temp.

FI

Cooling Max. Supply Temp.

C O O L I N G M A X . S U P P LY T E M P.

Dew Point Margin

In this menu the maximum allowed supply temperature for the zone can be set. The supply temperature is not allowed to rise above this value.

Dew Point Offset

FR

C A L C U L AT E D S U P P LY S E T P O I N T

In this menu the calculated supply setpoint for the zone can be overidden. This temperature is used as setpoint for the supply temperature.

HR HU IT

To set the maximum allowed supply temperature: 1. Select Cooling Max. supply temp. 2. Press the navigation wheel to confirm selection.

To override the calculated supply setpoint:

3. Set the value.

1. Select Calculated supply setpoint.

Default: 25.0 ˚C

2. Press the navigation wheel to confirm selection.

Setting range: 5.0 (or min. supply temp) – 40.0 ˚C, 0.1 ˚C increments

3. Select Manual. 4. Set the override value.

LT

4. Confirm the new setting by pressing the navigation wheel again.

4. Confirm the new setting by pressing the navigation wheel again.

Setting range: -5.0 – 70.0 ˚C, 0.1 ˚C increments

5. Confirm the new setting by pressing the navigation wheel again.

LV NL NO PL PT RO RU SE SK 66

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK DEW POINT MARGIN

Heating Indoor Temp. Settings

In this menu the dew point margin for the zone can be set. The dew point temperature is calculated using the current room temperature and relative humidity.

This menu enables access to settings related to the room temperature sensor in the zone.

CZ

This menu and its submenus are only shown if Heating Mode is set to Outdoor + Indoor comp. for the zone.

DE

When the calculated supply temperature is lower than the dew point temperature + Dew Point Offset this value is added to the calculated supply temperature.

MENU TREE*

To set the dew point margin:

DK

Heating Indoor Temp. Settings

1. Select Dew Point Margin.

Indoor Setpoint

2. Press the navigation wheel to confirm selection.

Calculated Indoor Setpoint

3. Set the value.

ECO-Comf. Status

Default: 4.0 ˚C

Setting range: -1.0 – 10.0 ˚C

Indoor Setpoint Influence (Lower)

4. Confirm the new setting by pressing the navigation wheel again.

*

DEW POINT OFFSET

The offset is used together with the dew point temperature to decide when to increase the calculated supply temperature with the value set in Dew Point Margin.

This information is only shown if Zone Setup is set to Stand Alone Control for the zone.

To set the dew point offset:

1. Select Indoor Setpoint.

1. Select Dew Point Offset.

2. Press the navigation wheel to confirm selection.

2. Press the navigation wheel to confirm selection.

3. Set the value.

Default: 1.0 ˚C

Setting range: 0.0 – 4.0 ˚C

4. Confirm the new setting by pressing the navigation wheel again.

FI

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

INDOOR SETPOINT

ES

Indoor Setpoint Influence (Upper)

In this menu the dew point offset for the zone can be set. The dew point temperature is calculated using the current room temperature and relative humidity.

3. Set the value.

EE

FR

In this menu the indoor temperature setpoint for the zone is set.

HR HU

To set the indoor temperature setpoint:

Default: 21.0 ˚C

Setting range: 5.0 – 35.0 ˚C, 0.1 ˚C increments

IT LT

4. Confirm the new setting by pressing the navigation wheel again.

LV

CALCULATED INDOOR SETPOINT

NL

This menu shows the calculated indoor setpoint for the zone.

NO

This information is only shown if Zone Setup is set to Stand Alone Control and if ECO-Comf mode is set to ECO for the zone.

PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

67


UK CZ

ECO-COMF STATUS

INDOOR SETPOINT INFLUENCE (UPPER)

This menu shows if the zone is set in ECO mode.

In this menu the indoor setpoint influence (upper) is set. If the measured indoor temperature is lower than the indoor temperature setpoint, the supply temperature sepoint will be increased using this value.

This information is only shown if ECO-Comf mode is set to ECO for the zone.

DE

INDOOR SETPOINT INFLUENCE (LOWER) In this menu the indoor setpoint influence (lower) is set. If the measured indoor temperature is higher than the indoor temperature setpoint, the supply temperature sepoint will be lowered using this value.

DK EE

This menu is used to to keep the measured room temperature as close as possible to the indoor temperature setpoint.

ES

N OT E ! If the value is set too high it can lead to the system being unstable and the room temperature will start fluctuating.

FI FR HR

N OT E ! If the value is set too high it can lead to the system being unstable and the room temperature will start fluctuating. To set the indoor setpoint influence (upper): 1. Select Indoor Setpoint Influence (Upper). 2. Press the navigation wheel to confirm selection. 3. Set the value.

To set the indoor setpoint influence (lower):

Default: 4.0 ˚C

1. Select Indoor Setpoint Influence (Lower).

Setting range: 0.0 – 10.0 ˚C, 0.1 ˚C increments

2. Press the navigation wheel to confirm selection.

4. Confirm the new setting by pressing the navigation wheel again.

3. Set the value.

HU

This menu is used to to keep the measured room temperature as close as possible to the indoor temperature setpoint.

Default: 4.0 ˚C

Setting range: 0.0 – 10.0 ˚C, 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again.

IT LT LV NL NO PL PT RO RU SE SK 68

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Comf. - ECO

To edit/create the ECO-Comf Schedule:

This menu enables access to settings related to the controller Comfort/ECO modes.

1. Select ECO-Comf Schedule.

This menu and its submenus are only shown if Zone Setup is set to Stand Alone Control and if Heating Mode is set to Outdoor + Indoor comp. for the zone.

CZ

2. Press the navigation wheel to confirm selection.

The current schedule is showing.

DE

3. Select a day. 4. Press the navigation wheel to confirm selection.

MENU TREE

Comf. - ECO ECO Setback ECO-Comf Status ECO-Comf Schedule

ECO SETBACK In this menu the ECO setback temperature is set. The parameter reduces the current setpoint with the set value. If the setback is set to 0 the zone will resume its normal operation, even if it is set in ECO mode. To set the ECO setback value: 1. Select ECO Setback. 2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 4.0 ˚C

Setting range: 0.0 – 10.0 ˚C, 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again. ECO-COMF STATUS This menu shows if the zone is set in ECO or Comf (comfort) mode. ECO-COMF SCHEDULE In this menu a schedule for switching between Comfort and ECO mode can be created. The default schedule is set to Comfort mode 24h a day, 7 days a week.

W arning ! Ensure that different schedules cannot enable ECO and Comf and the same time. This may cause an error where the controller must be reset to factory default values.

DK

All current schedule settings are shown, each line representing a switch between Comfort and ECO mode. If entering the menu for the first time only one line is present, showing Comf starting at 00:00 every day of the week.

EE ES

5. Select an existing line to edit or 00:00 Add new to add a new setting.

FI

6. Select wether to edit the hours, minutes, mode or day of the week. HOURS: Set at which hour the mode will start and press the navigation wheel to confirm selection.

FR

MINUTES: Set at which minte of the hour the mode will start and press the navigation wheel to confirm selection.

HR HU

MODE: Select a mode which should start at the set time and press the navigation wheel to confirm selection. Select between Comf, ECO and Delete switch time. Delete switch time erases the current line when selecting OK and pressing the navigation wheel.

IT LT

DAY OF THE WEEK:

Select which days of the week, at the set time the selected mode should start.

LV

7. Select OK at the end of the line, when done, and press the navigation wheel to confirm selection.

NL

A new line has been added to the schedule.

NO

8. Redo steps 5 and 6 until the schedule is complete. 9. Press the back button on the controller to exit the schedule setup.

PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

69


UK Heating Curve

Cooling Curve

CZ

This menu enables access to heating curve settings for the zone. Settings such as the slope (Setting) and offset of the heating curve.

This menu enables access to cooling curve settings for the zone. Settings such as the slope (Setting) and offset of the heating curve.

DE

This menu is only shown if one of the following requirements are met:

This menu is only shown if one of the following requirements are met:

DK

• System Type is set to 2 Pipe, and Indoor Cooling Only is set to No.

• System Type is set to 2 Pipe.

EE

• System Type is set to 4 Pipe, and Z1&2 Operation Mode is set to Only Heating or Heating And Cooling.

• System Type is set to 4 Pipe, and Z1&2 Operation Mode is set to Only Cooling or Heating And Cooling. MENU TREE

MENU TREE

ES

Cooling Curve

Heating Curve

FI

Setting Setting

Offset

Offset

Cooling Curve

Heating Curve

SETTING

FR

SETTING In this menu the slope of the heating curve is selected.

HR

To select a heating curve: 1. Select Setting.

HU

2. Press the navigation wheel to confirm selection.

IT LT

Default: 0.2

Setting range: 0.1 – 1.6, 0.1 increments

Setting range: 0.1 – 1.6, 0.1 increments

1. Select Offset. 2. Press the navigation wheel to confirm selection.

PT

3. Set the value.

To offset the heating curve:

PL

2. Press the navigation wheel to confirm selection.

Default: 0.9

In this menu the the heating curve can be offset. The offset can be used for temporary changes to the heating curve.

NO

1. Select Setting.

OFFSET

NL

To select a heating curve:

3. Set the value.

4. Confirm the new setting by pressing the navigation wheel again.

LV

In this menu the slope of the heating curve is selected.

4. Confirm the new setting by pressing the navigation wheel again. OFFSET In this menu the the heating curve can be offset. The offset can be used for temporary changes to the heating curve. To offset the heating curve: 1. Select Offset. 2. Press the navigation wheel to confirm selection. 3. Set the value.

3. Set the value.

Default: 0

Default: 0

Setting range: -8 – 8, 1 increments

Setting range: -8 – 8, 1 increments

4. Confirm the new setting by pressing the navigation wheel again.

RO

HEATING CURVE

RU

This menu shows the heating curve, and max/min supply temperature limits, for the zone.

4. Confirm the new setting by pressing the navigation wheel again. COOLING CURVE This menu shows the cooling curve, and max/min supply temperature limits, for the zone.

SE SK 70

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Manual Operation

MIXING VALVE

This menu enables access to manual operation mode in the zone.

In this menu the mixing valve can be overriden opened or closed manually.

When manual operation mode is activated, access to manual control (override) of the circulation pump and mixing valve is enabled.

This menu is only shown if Manual Mode is set to On.

DE

To override the mixing valve setting: 1. Select Mixing valve.

MENU TREE*

DK

2. Press the navigation wheel to confirm selection.

Manual Operation Manual Mode

*

CZ

3. Select Manual.

Pump

4. Set the override value.

Mixing valve

Default: 0 %

Setting range: 0 – 100 %, 1 % increments.

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

To activate manual operation mode:

EE ES

5. Confirm the new setting by pressing the navigation wheel again.

FI

1. Select Manual Mode. 2. Press the navigation wheel to confirm selection.

FR

3. Select On. 4. Confirm the new setting by pressing the navigation wheel again.

HR

PUMP

HU

In this menu the pump can be overidden and turned on or off manually. This menu is only shown if Zone Setup is set to Stand Alone Control, Dehumidifier is set to Disable, and Manual Mode is set to On.

IT LT

To override the circulation pump operation: 1. Select Pump. 2. Press the navigation wheel to confirm selection.

LV

3. Select Manual. 4. Select On.

Default: Off

Setting range: Off/On

NL NO

5. Confirm the new setting by pressing the navigation wheel again.

PL PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

71


UK Pump

Pump Exercise.

CZ

This menu enables access to pump settings in the zone.

To select a day of the week for pump exercise: 1. Select Exercise Day of the Week.

DE

This menu is only shown if Zone Setup is set to Stand Alone Control, and if Dehumidifier is disabled for the zone.

3. Select a day.

MENU TREE*

DK

Pump Pump Exercise Exercise Day of the Week

EE

Exercise Hour Exercise Min

ES

*

FI FR HR HU

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

EXERCISE HOUR In this menu the hour of the day for pump exercise is set.

In this menu pump exercise can be activated.

To select an hour of the day for pump exercise:

To activate pump exercise:

1. Select Exercise Hour.

1. Select Pump Exercise.

2. Press the navigation wheel to confirm selection.

2. Press the navigation wheel to confirm selection.

3. Set the value.

3. Select Pump Exercise.

Default: 8 h

Setting range: 0 – 23 h, 1 h increments

Default: No Exercise

Setting range: No Exercise/Pump Exercise

In this menu the day of the week for pump exercise is set. This menu is only shown if Pump Exercise is set to

LV

4. Confirm the setting by pressing the navigation wheel again.

PUMP EXERCISE

EXERCISE DAY OF THE WEEK

LT

Setting range: Monday – Sunday

This menu is only shown if Pump Exercise is set to Pump Exercise.

4. Confirm the new setting by pressing the navigation wheel again.

IT

2. Press the navigation wheel to confirm selection.

4. Confirm the setting by pressing the navigation wheel again. EXERCISE MIN In this menu the minute of the hour for pump exercise is set. This menu is only shown if Pump Exercise is set to Pump Exercise. To select a minute of the hour for pump exercise: 1. Select Exercise Min. 2. Press the navigation wheel to confirm selection.

NL

3. Set the value.

NO

Default: 0 min

Setting range: 0 – 59 min, 1 min increments

4. Confirm the setting by pressing the navigation wheel again.

PL PT RO RU SE SK 72

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK I-TIME

Mixing Valve This menu enables access to mixing valve settings in the zone.

CZ

To set the I-time:

MENU TREE*

DE

1. Select I-time.

Mixing Valve

*

In this menu the I-time for the mixing valve regulation is set.

Heating

2. Press the navigation wheel to confirm selection.

Cooling

3. Set the value.

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

HEATING This menu enables access to mixing valve settings in the zone while in heating mode.

Default: 35 seconds

Setting range: 5 – 300 seconds, 1 second increments

• System Type is set to 2 Pipe and Indoor Cooling Only is set to No.

To set the actuator running time:

Heating P-area I-time

ES

A C T U AT O R R U N N I N G T I M E

In this menu the actuator running time for the mixing valve regulation is set.

MENU TREE

EE

4. Confirm the setting by pressing the navigation wheel again.

This menu is only shown if one of the following requirements are met:

• System Type is set to 4 Pipe and Z1&2 Operation Mode is set to Only Heating or Heating And Cooling.

DK

FI

1. Select Actuator running time.

FR

2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 120 seconds

Setting range: 0 – 500 seconds, 1 second increments

HR HU

4. Confirm the setting by pressing the navigation wheel again.

Actuator running time

IT

P-AREA

In this menu the P-area for the mixing valve regulation is set.

LT

To set the P-area:

LV

1. Select P-area. 2. Press the navigation wheel to confirm selection.

NL

3. Set the value.

Default: 140.0 ˚C

Setting range: 2.0 – 500.0 ˚C, 0.1 ˚C increments

NO

4. Confirm the setting by pressing the navigation wheel again.

PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

73


UK I-TIME

COOLING

CZ

This menu enables access to mixing valve settings in the zone while in cooling mode.

DE

This menu is only shown if one of the following requirements are met: • System Type is set to 2 Pipe and Indoor Cooling Only is set to Yes or No.

DK

• System Type is set to 4 Pipe and Z1&2 Operation Mode is set to Only Cooling or Heating And Cooling.

EE

Cooling P-area I-time

FI

Actuator running time P-AREA

FR

In this menu the P-area for the mixing valve regulation is set.

HR

2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 50 seconds

Setting range: 5 – 300 seconds, 1 second increments

A C T U AT O R R U N N I N G T I M E

In this menu the actuator running time for the mixing valve regulation is set. To set the actuator running time: 1. Select Actuator running time. 2. Press the navigation wheel to confirm selection. 3. Set the value.

1. Select P-area.

Default: 60 seconds

Setting range: 0 – 500 seconds, 1 second increments

3. Set the value.

IT

1. Select I-time.

To set the P-area:

2. Press the navigation wheel to confirm selection.

HU

To set the I-time:

4. Confirm the setting by pressing the navigation wheel again.

MENU TREE

ES

In this menu the I-time for the mixing valve regulation is set.

Default: 200.0 ˚C

Setting range: 2.0 – 500.0 ˚C, 0.1 ˚C increments

4. Confirm the setting by pressing the navigation wheel again.

4. Confirm the setting by pressing the navigation wheel again.

LT LV NL NO PL PT RO RU SE SK 74

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Dehumidifier Control

Seasonal Shut Off

This menu enables access to dehumidifier settings in the zone.

This menu enables access to seasonal shut off settings in the zone.

This menu is only shown if Dehumidifier Control is enabled in the startup wizard for the zone.

MENU TREE*

CZ DE

Seasonal Shut Off

MENU TREE

Heating

DK

Cooling

Dehumidifier Control Dew Point Margin

*

Dead Zone

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

EE

HEATING DEW POINT MARGIN In this menu the dew point margin, for controlling the dehumidifier, in the zone can be set. The dehumidifier is started when the supply temperature is equal or lower than the dew point temperature + dew point margin. The dehumidifier is shut off when the supply temperature is equal or higher than the dew point temperature + dew point margin + deadzone temperature.

This menu enables access to seasonal shut off settings in the zone, while in heating mode. This menu is only shown if one of the following requirements are met:

To set the dew point margin: 1. Select Dew Point Margin.

MENU TREE*

Setting range: -1.0 – 10.0 ˚C

Shut Off Outdoor Temp.

DEAD ZONE

T. Indoor Delay

1. Select Dead Zone. 2. Press the navigation wheel to confirm selection. 3. Set the value.

LT

Shut Off Indoor Temp.

*

LV

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

PUMP STOP

In this menu a function to stop the circulation pump, when requirements are met, is enabled.

NL

This menu is only shown if Zone Setup is set to Stand Alone Control, and Dehumidifier is set to Disable.

Default: 2.0 ˚C

To enable the function:

Setting range: 1.0 – 5.0 ˚C

1. Select Pump Stop.

4. Confirm the new setting by pressing the navigation wheel again.

IT

T. Outdoor Setpoint T. Outdoor Delay

To set the dead zone:

HU

Valve Close

4. Confirm the new setting by pressing the navigation wheel again.

In this menu the dead zone (hysteresis) for when to shut off the dehumidifier in the zone can be set.

HR

Pump Stop

3. Set the value.

FR

Heating

2. Press the navigation wheel to confirm selection.

Default: 4.0 ˚C

FI

• System Type is set to 2 Pipe, and Indoor Cooling Only is set to No. • System Type is set to 4 Pipe, and Z1&2 Operation Mode is set to Only Heating or Heating And Cooling.

ES

NO PL

2. Press the navigation wheel to confirm selection.

PT

3. Select Enable.

Default: Disable

Setting range: Disable/Enable

RO

4. Confirm the setting by pressing the navigation wheel again.

RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

75


UK CZ

VA LV E C LO S E

T. O U T D O O R S E T P O I N T

In this menu a function to close the mixing valve, when requirements are met, is enabled.

In this menu the outdoor temperature setpoint for stopping the circulation pump, and/or closing the mixing valve, in the zone is set.

To enable the function:

DE

1. Select Valve Close. 2. Press the navigation wheel to confirm selection.

DK

3. Select Enable.

EE

Default: Disable

Setting range: Disable/Enable

4. Confirm the setting by pressing the navigation wheel again.

ES

S H U T O F F O U T D O O R T E M P.

This menu is only shown if Shut Off Outdoor Temp. is enabled. To set an outdoor temperature setpoint: 1. Select T Outdoor Setpoint. 2. Press the navigation wheel to confirm selection. 3. Select Enable.

Default: 17.0 ˚C

Setting range: 0.0 – 40.0 ˚C, 0.1 ˚C increments

FI

In this menu the function to stop the circulation pump and/or when to close the mixing valve, at an outdoor temperature setpoint is enabled/disabled for the zone.

4. Confirm the setting by pressing the navigation wheel again.

FR

This menu is only shown if Pump Stop and/or Valve Close is enabled.

In this menu the time delay for how long the outdoor temperature must be equal or higher than T Outdoor Setpoint before stopping the circulation pump, and/or closing the mixing valve, in the zone is set.

To set an shut off outdoor temperature:

HR

1. Select Shut Off Outdoor Temp..

HU IT

2. Press the navigation wheel to confirm selection.

This menu is only shown if Shut Off Outdoor Temp. is enabled.

3. Select Enable.

To set the delay:

Default: Disable

1. Select T. Outdoor Delay.

Setting range: Disable/Enable

4. Confirm the setting by pressing the navigation wheel again.

LT

T. O U T D O O R D E L AY

2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 24 h

Setting range: 0 – 24 h, 1 h increments

4. Confirm the setting by pressing the navigation wheel again.

LV NL NO PL PT RO RU SE SK 76

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK S H U T O F F I N D O O R T E M P.

COOLING

In this menu the function to stop the circulation pump, and/or when to close the mixing valve, at an indoor temperature setpoint is enabled/disabled for the zone.

This menu enables access to seasonal shut off settings in the zone, while in cooling mode.

CZ

This menu is only shown if one of the following requirements are met:

DE

This menu is only shown if Pump Stop and/or Valve Close is enabled, and if Heating Mode is set to Outdoor + Indoor comp. for the zone. To set an shut off outdoor temperature: 1. Select Shut Off Outdoor Temp.. 2. Press the navigation wheel to confirm selection.

• System Type is set to 2 Pipe.

EE

MENU TREE*

3. Select Enable.

Cooling

Default: Disable

Pump Stop

Setting range: Disable/Enable

Valve Close

In this menu the time delay for how long the indoor temperature must be equal or higher than the indoor setpoint before stopping the circulation pump, and/or closing the mixing valve, in the zone is set.

ES

T. Outdoor Setpoint

4. Confirm the setting by pressing the navigation wheel again. T . I N D O O R D E L AY

DK

• System Type is set to 4 Pipe, and Z1&2 Operation Mode is set to Only Cooling or Heating And Cooling.

FI

T. Outdoor Delay *

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

FR

PUMP STOP

In this menu a function to stop the circulation pump, when requirements are met, is enabled.

This menu is only shown if Shut Off Indoor Temp. is enabled.

To enable the function:

To set the delay:

2. Press the navigation wheel to confirm selection.

1. Select T. Indoor Delay.

3. Select Enable.

2. Press the navigation wheel to confirm selection.

Default: Disable

3. Set the value.

Setting range: Disable/Enable

Default: 0 h

Setting range: 0 – 5 h, 1 h increments

4. Confirm the setting by pressing the navigation wheel again.

HR

1. Select Pump Stop.

HU IT LT LV

4. Confirm the setting by pressing the navigation wheel again.

NL NO PL PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

77


UK VA LV E C LO S E

In this menu a function to close the mixing valve, when requirements are met, is enabled.

CZ

To enable the function:

DE

1. Select Valve Close. 2. Press the navigation wheel to confirm selection.

DK

3. Select Enable.

EE

Default: Disable

Setting range: Disable/Enable

H/C Switchover This menu enables access to settings related to switching between heating and cooling in the zone. This menu is only shown if System Type is set to 4 Pipe and Z1&2 Operation Mode is set to Heating And Cooling. MENU TREE* H/C Switchover H/C Switchover Outdoor Trigger Temp.

4. Confirm the setting by pressing the navigation wheel again.

ES

Outdoor Trigger Delay Indoor Trigger Temp.

T. O U T D O O R S E T P O I N T

Indoor Trigger Delay.

In this menu the outdoor temperature setpoint for stopping the circulation pump, and/or closing the mixing valve, in the zone is set.

FI

To set an outdoor temperature setpoint:

FR

1. Select T Outdoor Setpoint. 2. Press the navigation wheel to confirm selection.

HR

3. Select Enable.

HU

Default: 17.0 ˚C

Setting range: 0.0 – 40.0 ˚C, 0.1 ˚C increments

4. Confirm the setting by pressing the navigation wheel again.

IT

T . O U T D O O R D E L AY

In this menu the time delay for how long the outdoor temperature must be equal or higher than T Outdoor Setpoint before stopping the circulation pump, and/or closing the mixing valve, in the zone is set.

LT LV

Supply Setpoint for HC Switch Hysteresis *

H/C SWITCHOVER In this menu settings for switching the zone between heating and cooling is set. To select heating/cooling swithover function for the zone: 1. Select H/C Switchover. 2. Press the navigation wheel to confirm selection. 3. Select heating/cooling switchover function for the zone.

• Indoor and Outdoor uses the indoor and outdoor temperatures and time delays to switch the zone between heating and cooling.

• Supply Water Temp. uses the supply water temperature and a hysteresis to switch the zone between heating and cooling.

• Contact Input uses an external signal to switch the zone between heating and cooling.

• Force Heating sets the zone in forced heating.

• Force Cooling sets the zone in forced cooling.

To set the delay: 1. Select T. Outdoor Delay.

NL

2. Press the navigation wheel to confirm selection. 3. Set the value.

NO PL

Default: 24 h

Setting range: 0 – 24 h, 1 h increments

4. Confirm the setting by pressing the navigation wheel again.

PT

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

4. Confirm the new setting by pressing the navigation wheel again.

RO RU SE SK 78

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK OUTDOOR TRIGGER TEMP.

INDOOR TRIGGER TEMP.

In this menu one of the triggers (outdoor temperature) for switching the zone between heating and cooling is set.

In this menu one of the triggers (indoor temperature) for switching the zone between heating and cooling is set.

N OT E ! All triggers and time delays must be met for the zone to switch heating/cooling mode.

N OT E ! All triggers and time delays must be met for the zone to switch heating/cooling mode.

This menu is only shown if H/C Switchover is set to Indoor and Outdoor.

This menu is only shown if H/C Switchover is set to Indoor and Outdoor.

To set the outdoor trigger temperature:

To set the indoor trigger temperature:

1. Select Outdoor Trigger Temp.

1. Select Indoor Trigger Temp.

2. Press the navigation wheel to confirm selection.

2. Press the navigation wheel to confirm selection.

3. Set the value.

3. Set the value.

Default: 20.0 ˚C

Default: 22.0 ˚C

Setting range: 5.0 – 30.0 ˚C, 0.1 ˚C increments

Setting range: 5.0 – 30.0 ˚C, 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again.

4. Confirm the new setting by pressing the navigation wheel again.

OUTDOOR TRIGGER DELAY

INDOOR TRIGGER DELAY

In this menu one of the triggers (delay for outdoor temperature) for switching the zone between heating and cooling is set.

In this menu one of the triggers (delay for indoor temperature) for switching the zone between heating and cooling is set.

N OT E ! All triggers and time delays must be met for the zone to switch heating/cooling mode.

N OT E ! All triggers and time delays must be met for the zone to switch heating/cooling mode.

This menu is only shown if H/C Switchover is set to Indoor and Outdoor.

This menu is only shown if H/C Switchover is set to Indoor and Outdoor.

To set the outdoor trigger delay:

To set the indoor trigger delay:

1. Select Outdoor Trigger Delay.

1. Select Indoor Trigger Delay.

2. Press the navigation wheel to confirm selection.

2. Press the navigation wheel to confirm selection.

3. Set the value.

3. Set the value.

Default: 24 h

Default: 24 h

Setting range: 1 – 48 h, 1 h increments

Setting range: 1 – 48 h, 1 h increments

4. Confirm the new setting by pressing the navigation wheel again.

CZ DE DK EE ES FI FR HR HU IT LT LV NL NO

4. Confirm the new setting by pressing the navigation wheel again.

PL PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

79


UK CZ

SUPPLY SETPOINT FOR HC SWITCH

HYSTERESIS

In this menu the supply temperature setpoint for switching between heating and cooling is set.

In this menu the hysteresis which is used to switch between heating and cooling using Supply Setpoint for HC Switch is set.

The zone switches to heating when the supply temperature is higher than Supply Setpoint for HC Switch. The zone switches back when the supply temperature is lower than Supply Setpoint for HC Switch - Hysteresis.

DE DK

The zone switches to cooling when the supply temperature is lower than Supply Setpoint for HC Switch. The zone switches back when the supply temperature is lower than Supply Setpoint for HC Switch + Hysteresis.

EE ES

N OT E ! When using this switch mode, the heating/ cooling switch is done in the heat pump/ chiller. The Move PRO controller switches the operation mode when it detects the change in supply temperture.

FI FR

No diverting valves are controlled in this mode.

HR

This menu is only shown if H/C Switchover is set to Supply Water Temp..

HU

To set the supply temperature setpoint for HC switch: 1. Select Supply Setpoint for HC Switch.

IT

2. Press the navigation wheel to confirm selection. 3. Set the value.

LT LV

Default: 18 ˚C

Setting range: 5 – 30 ˚C, 1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again.

To set the hysteresis: 1. Select Hysteresis. 2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 2 ˚C

Setting range: 0 – 4 ˚C, 1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again. Condensation Delay In this menu the condensation delay in the zone is set. If condensation is not detected (by the condensation sensor in the zone) during the time set in the delay, the condensation status (in the zone information menu) switches to No. This menu is only shown if Condensation Sensor is enabled in the startup wizard for the zone. To set the condensation delay: 1. Select Condensation Delay. 2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 10 min

Setting range: 0 – 120 min, 1 min increments

4. Confirm the new setting by pressing the navigation wheel again.

NL NO PL PT RO RU SE SK 80

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Z one 2 S ettings

HEATING

In this menu parameter settings for zone 2 can be set or changed. Menu tree* Zone 2 Settings Supply Temp. Settings Heating Indoor Temp. Settings DHW Circ Return Settings Comf. - ECO Heating Curve Cooling Curve Manual Operation

This menu enables access to settings related to the heating supply temperature in the zone.

CZ

This menu is only shown if one of the following requirements are met:

DE

• System Type is set to 2 Pipe, Indoor Cooling Only is set to No, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone.

DK

• System Type is set to 4 Pipe, Z1&2 Operation Mode is set to Only Heating or Heating And Cooling, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone.

Heating

Mixing Valve

Calculated Supply Setpoint

Dehumidifier Control

Heating Min. Supply Temp.

Seasonal Shut Off

Heating Max. Supply Temp.

H/C Switchover

Deviation alarm limit

Condensation Delay

Deviation alarm delay

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

Supply Temp. Settings This menu enables access to settings related to the supply temperature in the zone. MENU TREE*

ES

MENU TREE

Pump

*

EE

FI FR HR

C A L C U L AT E D S U P P LY S E T P O I N T

In this menu the calculated supply setpoint for the zone can be overidden. This temperature is used as setpoint for the supply temperature.

HU

To override the calculated supply setpoint:

IT

1. Select Calculated supply setpoint. 2. Press the navigation wheel to confirm selection.

Supply Temp. Settings Heating Cooling DHW Supply Setpoint Overheating alarm limit Overheating alarm delay Deviation alarm limit

LT

3. Select Manual. 4. Set the override value.

LV

Setting range: -5.0 – 70.0 ˚C, 0.1 ˚C increments

5. Confirm the new setting by pressing the navigation wheel again.

NL

Deviation alarm delay *

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

NO PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

81


UK H E AT I N G M I N . S U P P LY T E M P.

D E V I AT I O N A L A R M L I M I T

CZ

In this menu the minimum allowed supply temperature for the zone can be set. The supply temperature is not allowed to fall below this value.

DE

To set the minimum allowed supply temperature:

In this menu the deviation alarm limit for the supply temperature in the zone is set. If the difference between the measured and the calculated supply temperatures are higher than the set limit during the time set in Deviation alarm delay, the alarm is triggered.

1. Select Heating Min. supply temp. 2. Press the navigation wheel to confirm selection.

DK

3. Set the value.

EE ES

Default: 15.0 ˚C

Setting range: 5.0 – 35.0 ˚C (or max. supply temp), 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again. H E AT I N G M A X . S U P P LY T E M P.

FI

In this menu the maximum allowed supply temperature for the zone can be set. The supply temperature is not allowed to rise above this value.

FR

HU IT

2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 10.0 ˚C

Setting range: 0.0 – 50.0 ˚C, 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again. D E V I AT I O N A L A R M D E L AY

1. Select Heating Max. supply temp. 2. Press the navigation wheel to confirm selection.

To set the deviation alarm delay:

3. Set the value.

1. Select Deviation alarm delay.

Default: 70.0 ˚C

Setting range: 5.0 (or min. supply temp) – 70.0 ˚C, 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again.

LT

1. Select Deviation alarm limit.

In this menu the deviation alarm delay for the deviation alarm limit in the zone is set. If the difference between the measured and the calculated supply temperatures are higher than Deviation alarm limit during the set delay, the alarm is triggered.

To set the maximum allowed supply temperature:

HR

To set the deviation alarm limit:

2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 5 min

Setting range: 0 – 30 min, 1 min increments

4. Confirm the new setting by pressing the navigation wheel again.

LV NL NO PL PT RO RU SE SK 82

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK COOLING

C O O L I N G M I N . S U P P LY T E M P.

This menu enables access to settings related to the cooling supply temperature in the zone.

In this menu the minimum allowed supply temperature for the zone can be set. The supply temperature is not allowed to fall below this value.

CZ

This menu is only shown if one of the following requirements are met:

To set the minimum allowed supply temperature:

DE

• System Type is set to 2 Pipe, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone. • System Type is set to 4 Pipe, Z1&2 Operation Mode is set to Only Cooling or Heating And Cooling, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone.

1. Select Cooling Min. supply temp. 2. Press the navigation wheel to confirm selection.

DK

3. Set the value.

Default: 8.0 ˚C

Setting range: 5.0 – 40.0 ˚C (or max. supply temp), 0.1 ˚C increments

EE ES

4. Confirm the new setting by pressing the navigation wheel again.

MENU TREE

Cooling

C O O L I N G M A X . S U P P LY T E M P.

Calculated Supply Setpoint Cooling Min. Supply Temp. Cooling Max. Supply Temp. Dew Point Margin Dew Point Offset C A L C U L AT E D S U P P LY S E T P O I N T

In this menu the calculated supply setpoint for the zone can be overidden. This temperature is used as setpoint for the supply temperature. To override the calculated supply setpoint: 1. Select Calculated supply setpoint. 2. Press the navigation wheel to confirm selection.

FI

In this menu the maximum allowed supply temperature for the zone can be set. The supply temperature is not allowed to rise above this value.

FR

To set the maximum allowed supply temperature: 1. Select Cooling Max. supply temp.

HR

2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 25.0 ˚C

Setting range: 5.0 (or min. supply temp) – 40.0 ˚C, 0.1 ˚C increments

HU IT

4. Confirm the new setting by pressing the navigation wheel again.

LT

3. Select Manual. 4. Set the override value.

LV

Setting range: -5.0 – 70.0 ˚C, 0.1 ˚C increments

5. Confirm the new setting by pressing the navigation wheel again.

NL NO PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

83


UK CZ

DEW POINT MARGIN

DHW SUPPLY SETPOINT

In this menu the dew point margin for the zone can be set. The dew point temperature is calculated using the current room temperature and relative humidity.

In this menu the supply temperature setpoint for domestic hot water production is set.

When the calculated supply temperature is lower than the dew point temperature + Dew Point Offset this value is added to the calculated supply temperature.

DE DK EE ES

1. Select Supply Setpoint.

1. Select Dew Point Margin.

2. Press the navigation wheel to confirm selection.

2. Press the navigation wheel to confirm selection.

3. Set the value.

3. Set the value.

Default: 60.0 ˚C

Setting range: 5.0 – 95.0 ˚C, 0.1 ˚C increments

Default: 4.0 ˚C

Setting range: -1.0 – 10.0 ˚C

DEW POINT OFFSET

FR

In this menu the dew point offset for the zone can be set. The dew point temperature is calculated using the current room temperature and relative humidity.

HR

The offset is used together with the dew point temperature to decide when to increase the calculated supply temperature with the value set in Dew Point Margin.

HU

To set the dew point offset:

IT

1. Select Dew Point Offset. 2. Press the navigation wheel to confirm selection.

LT

3. Set the value.

LV

To set the supply temperature setpoint:

To set the dew point margin:

4. Confirm the new setting by pressing the navigation wheel again.

FI

This menu is only shown if Zone Setup is set to Domestic Hot Water for the zone.

Default: 1.0 ˚C

Setting range: 0.0 – 4.0 ˚C

4. Confirm the new setting by pressing the navigation wheel again. OVERHEATING ALARM LIMIT In this menu the overheating alarm limit for domestic hot water production is set. If the supply temperature is higher than the set limit during the time set in Overheating alarm delay, the alarm is triggered. This menu is only shown if Zone Setup is set to Domestic Hot Water for the zone. To set the overheating alarm limit: 1. Select Overheating alarm limit. 2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 68.0 ˚C

Setting range: 65.0 – 120.0 ˚C, 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again.

4. Confirm the new setting by pressing the navigation wheel again.

NL NO PL PT RO RU SE SK 84

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK OVERHEATING ALARM DELAY

DEVIATION ALARM DELAY

In this menu the overheating alarm delay for the overheating alarm limit of the zone is set. If the supply temperature is higher than Overheating alarm limit, during the set delay, the alarm is triggered.

In this menu the deviation alarm delay for the deviation alarm limit in the zone is set. If the difference between the measured and the calculated supply temperatures are higher than Deviation alarm limit during the set delay, the alarm is triggered.

This menu is only shown if Zone Setup is set to Domestic Hot Water for the zone To set the overheating alarm delay: 1. Select Overheating alarm delay. 2. Press the navigation wheel to confirm selection. 3. Set the value.

DK

To set the deviation alarm delay:

EE

1. Select Deviation alarm delay. 2. Press the navigation wheel to confirm selection.

Default: 10 min

3. Set the value.

Setting range: 0 – 15 min, 1 min increments

Default: 60 seconds

Setting range: 0 – 600 seconds, 1 second increments

DEVIATION ALARM LIMIT

DE

This menu is only shown if Zone Setup is set to Domestic Hot Water for the zone.

4. Confirm the new setting by pressing the navigation wheel again.

CZ

ES FI

4. Confirm the new setting by pressing the navigation wheel again.

FR

In this menu the deviation alarm limit for the supply temperature in the zone is set. If the difference between the measured and the calculated supply temperatures are higher than the set limit during the time set in Deviation alarm delay, the alarm is triggered.

HR HU

This menu is only shown if Zone Setup is set to Domestic Hot Water for the zone. To set the deviation alarm limit:

IT

1. Select Deviation alarm limit. 2. Press the navigation wheel to confirm selection.

LT

3. Set the value.

Default: 10 ˚C

Setting range: 0.0 – 30.0 ˚C, 0.1 ˚C increments

LV

4. Confirm the new setting by pressing the navigation wheel again.

NL NO PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

85


UK Heating Indoor Temp. Settings

INDOOR SETPOINT INFLUENCE (LOWER)

CZ

This menu enables access to settings related to the room temperature sensor in the zone.

DE

This menu and its submenus are only shown if Heating Mode is set to Outdoor + Indoor comp. for the zone.

In this menu the indoor setpoint influence (lower) is set. If the measured indoor temperature is higher than the indoor temperature setpoint, the supply temperature sepoint will be lowered using this value. This menu is used to to keep the measured room temperature as close as possible to the indoor temperature setpoint.

MENU TREE*

DK

Heating Indoor Temp. Settings

N OT E ! If the value is set too high it can lead to the system being unstable and the room temperature will start fluctuating.

Indoor Setpoint

EE

Calculated Indoor Setpoint ECO-Comf. Status

ES

Indoor Setpoint Influence (Lower) Indoor Setpoint Influence (Upper)

FI *

FR HR

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

Default: 4.0 ˚C

In this menu the indoor temperature setpoint for the zone is set.

Setting range: 0.0 – 10.0 ˚C, 0.1 ˚C increments

2. Press the navigation wheel to confirm selection. 3. Set the value.

LV

3. Set the value.

1. Select Indoor Setpoint.

LT

2. Press the navigation wheel to confirm selection.

To set the indoor temperature setpoint:

IT

1. Select Indoor Setpoint Influence (Lower).

INDOOR SETPOINT

This information is only shown if Zone Setup is set to Stand Alone Control for the zone.

HU

To set the indoor setpoint influence (lower):

Default: 21.0 ˚C

Setting range: 5.0 – 35.0 ˚C, 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again. INDOOR SETPOINT INFLUENCE (UPPER) In this menu the indoor setpoint influence (upper) is set. If the measured indoor temperature is lower than the indoor temperature setpoint, the supply temperature sepoint will be increased using this value. This menu is used to to keep the measured room temperature as close as possible to the indoor temperature setpoint.

4. Confirm the new setting by pressing the navigation wheel again.

N OT E ! If the value is set too high it can lead to the system being unstable and the room temperature will start fluctuating.

CALCULATED INDOOR SETPOINT

NL

This menu shows the calculated indoor setpoint for the zone.

NO

This information is only shown if Zone Setup is set to Stand Alone Control and if ECO-Comf mode is set to ECO for the zone.

PL PT

To set the indoor setpoint influence (upper): 1. Select Indoor Setpoint Influence (Upper). 2. Press the navigation wheel to confirm selection. 3. Set the value.

ECO-COMF STATUS

Default: 4.0 ˚C

This menu shows if the zone is set in ECO mode.

Setting range: 0.0 – 10.0 ˚C, 0.1 ˚C increments

This information is only shown if ECO-Comf mode is set to ECO for the zone.

4. Confirm the new setting by pressing the navigation wheel again.

RO RU SE SK 86

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK DHW Circ Return Settings

Comf. - ECO

This menu enables access to settings related to the return temperature sensor.

This menu enables access to settings related to the controller Comfort/ECO modes.

CZ

This menu is only shown if Zone Setup is set to Domestic Hot Water for the zone.

This menu and its submenus are only shown if Zone Setup is set to Stand Alone Control and if Heating Mode is set to Outdoor + Indoor comp. for the zone.

DE

MENU TREE

DK

MENU TREE DHW Circ Return Settings

Comf. - ECO

DHW Circ Return Setpoint

ECO Setback

BoostPower

EE

ECO-Comf Status

DHW CIRC RETURN SETPOINT In this menu the return temperature setpoint for the zone is set.

ECO-Comf Schedule

ES

ECO SETBACK In this menu the ECO setback temperature is set. The parameter reduces the current setpoint with the set value.

FI

If the setback is set to 0 the zone will resume its normal operation, even if it is set in ECO mode.

FR

3. Set the value.

Default: 50.0 ˚C

To set the ECO setback value:

Setting range: 50.0 – 250.0 ˚C, 0.1 ˚C increments

1. Select ECO Setback.

To set the return temperature setpoint: 1. Select DHW Circ Return Setpoint. 2. Press the navigation wheel to confirm selection.

4. Confirm the new setting by pressing the navigation wheel again. BOOSTPOWER

2. Press the navigation wheel to confirm selection.

HU

3. Set the value.

Default: 4.0 ˚C

In this menu the boost power for domestic hot water production is set. The parameter is used to adjust the calculated supply temperature, if the difference between the supply and return temperatures is to large.

Setting range: 0.0 – 10.0 ˚C, 0.1 ˚C increments

This menu is only shown if Zone Setup is set to Domestic Hot Water for the zone.

ECO-COMF STATUS

To set the boost power:

HR

IT

4. Confirm the new setting by pressing the navigation wheel again.

LT

This menu shows if the zone is set in ECO or Comf (comfort) mode.

LV

1. Select BoostPower.

NL

2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 60 %

Setting range: 0 – 100 %, 1 % increments

NO PL

4. Confirm the new setting by pressing the navigation wheel again.

PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

87


UK ECO-COMF SCHEDULE

CZ

In this menu a schedule for switching between Comfort and ECO mode can be created.

DE

The default schedule is set to Comfort mode 24h a day, 7 days a week.

W arning !

DK

7. Select OK at the end of the line, when done, and press the navigation wheel to confirm selection.

A new line has been added to the schedule.

8. Redo steps 5 and 6 until the schedule is complete. 9. Press the back button on the controller to exit the schedule setup.

Ensure that different schedules cannot enable ECO and Comf and the same time. This may cause an error where the controller must be reset to factory default values.

EE

To edit/create the ECO-Comf Schedule: 1. Select ECO-Comf Schedule.

ES

2. Press the navigation wheel to confirm selection.

FI

The current schedule is showing.

3. Select a day. 4. Press the navigation wheel to confirm selection.

FR

HR HU

All current schedule settings are shown, each line representing a switch between Comfort and ECO mode. If entering the menu for the first time only one line is present, showing Comf starting at 00:00 every day of the week.

5. Select an existing line to edit or 00:00 Add new to add a new setting.

IT

6. Select wether to edit the hours, minutes, mode or day of the week.

LT

HOURS: Set at which hour the mode will start and press the navigation wheel to confirm selection.

LV

MINUTES: Set at which minte of the hour the mode will start and press the navigation wheel to confirm selection.

NL

MODE: Select a mode which should start at the set time and press the navigation wheel to confirm selection. Select between Comf, ECO and Delete switch time. Delete switch time erases the current line when selecting OK and pressing the navigation wheel.

NO PL PT

DAY OF THE WEEK:

Select which days of the week, at the set time the selected mode should start.

RO RU SE SK 88

U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Heating Curve

OFFSET

This menu enables access to heating curve settings for the zone. Settings such as the slope (Setting) and offset of the heating curve.

In this menu the the heating curve can be offset. The offset can be used for temporary changes to the heating curve.

CZ

This menu is only shown if one of the following requirements are met:

To offset the heating curve:

DE

• System Type is set to 2 Pipe, Indoor Cooling Only is set to No, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone. • System Type is set to 4 Pipe, Z1&2 Operation Mode is set to Only Heating or Heating And Cooling, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone. MENU TREE

1. Select Offset.

DK

2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 0

Setting range: -8 – 8, 1 increments

EE

4. Confirm the new setting by pressing the navigation wheel again.

ES

HEATING CURVE

Heating Curve Setting

FI

This menu shows the heating curve, and max/min supply temperature limits, for the zone.

Offset

FR

Heating Curve

SETTING

HR

In this menu the slope of the heating curve is selected. To select a heating curve:

HU

1. Select Setting. 2. Press the navigation wheel to confirm selection.

IT

3. Set the value.

Default: 0.9

Setting range: 0.1 – 1.6, 0.1 increments

LT

4. Confirm the new setting by pressing the navigation wheel again.

LV NL NO PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

89


UK Cooling Curve

OFFSET

CZ

This menu enables access to cooling curve settings for the zone. Settings such as the slope (Setting) and offset of the heating curve.

In this menu the the heating curve can be offset. The offset can be used for temporary changes to the heating curve.

DE

This menu is only shown if one of the following requirements are met:

To offset the heating curve:

DK

• System Type is set to 2 Pipe and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone.

EE

• System Type is set to 4 Pipe, Z1&2 Operation Mode is set to Only Cooling or Heating And Cooling, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone.

ES

MENU TREE

FI

1. Select Offset. 2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 0

Setting range: -8 – 8, 1 increments

4. Confirm the new setting by pressing the navigation wheel again. COOLING CURVE

Cooling Curve Setting

This menu shows the cooling curve, and max/min supply temperature limits, for the zone.

Offset

FR

Cooling Curve

SETTING

HR

In this menu the slope of the heating curve is selected. To select a heating curve:

HU

1. Select Setting. 2. Press the navigation wheel to confirm selection.

IT

3. Set the value.

LT

Default: 0.2

Setting range: 0.1 – 1.6, 0.1 increments

4. Confirm the new setting by pressing the navigation wheel again.

LV NL NO PL PT RO RU SE SK 90

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Manual Operation

MIXING VALVE

This menu enables access to manual operation mode in the zone.

In this menu the mixing valve can be overriden opened or closed manually.

When manual operation mode is activated, access to manual control (override) of the circulation pump and mixing valve is enabled.

This menu is only shown if Manual Mode is set to On.

DE

To override the mixing valve setting: 1. Select Mixing valve.

MENU TREE*

DK

2. Press the navigation wheel to confirm selection.

Manual Operation Manual Mode

*

CZ

3. Select Manual.

Pump

4. Set the override value.

Mixing valve

Default: 0 %

Setting range: 0 – 100 %, 1 % increments.

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

To activate manual operation mode:

EE ES

5. Confirm the new setting by pressing the navigation wheel again.

FI

1. Select Manual Mode. 2. Press the navigation wheel to confirm selection.

FR

3. Select On. 4. Confirm the new setting by pressing the navigation wheel again.

HR

PUMP

HU

In this menu the pump can be overidden and turned on or off manually. This menu is only shown if Zone Setup is set to Stand Alone Control or Domestic Hot Water, Dehumidifier is set to Disable, and Manual Mode is set to On.

IT LT

To override the circulation pump operation: 1. Select Pump.

LV

2. Press the navigation wheel to confirm selection. 3. Select Manual.

NL

4. Select On.

Default: Off

Setting range: Off/On

NO

5. Confirm the new setting by pressing the navigation wheel again.

PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

91


UK Pump

EXERCISE HOUR

CZ

This menu enables access to pump settings in the zone.

DE

This menu is only shown if Zone Setup is set to Stand Alone Control or Domestic Hot Water, and if Dehumidifier is disabled for the zone.

In this menu the hour of the day for pump exercise is set.

MENU TREE*

DK

To select an hour of the day for pump exercise: 1. Select Exercise Hour.

Pump

EE

Pump Exercise

2. Press the navigation wheel to confirm selection.

Exercise Day of the Week

3. Set the value.

Exercise Hour Exercise Min

ES

*

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

PUMP EXERCISE

FI

In this menu pump exercise can be activated. To activate pump exercise:

FR

1. Select Pump Exercise.

HR HU

Default: 8 h

Setting range: 0 – 23 h, 1 h increments

4. Confirm the setting by pressing the navigation wheel again. EXERCISE MIN In this menu the minute of the hour for pump exercise is set.

2. Press the navigation wheel to confirm selection.

This menu is only shown if Pump Exercise is set to Pump Exercise.

3. Select Pump Exercise.

To select a minute of the hour for pump exercise:

Default: No Exercise

1. Select Exercise Min.

Setting range: No Exercise/Pump Exercise

4. Confirm the new setting by pressing the navigation wheel again.

IT

This menu is only shown if Pump Exercise is set to Pump Exercise.

EXERCISE DAY OF THE WEEK

LT

In this menu the day of the week for pump exercise is set.

LV

This menu is only shown if Pump Exercise is set to Pump Exercise.

2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 0 min

Setting range: 0 – 59 min, 1 min increments

4. Confirm the setting by pressing the navigation wheel again.

To select a day of the week for pump exercise:

NL

1. Select Exercise Day of the Week. 2. Press the navigation wheel to confirm selection.

NO

3. Select a day.

Setting range: Monday – Sunday

4. Confirm the setting by pressing the navigation wheel again.

PL PT RO RU SE SK 92

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK I-TIME

Mixing Valve This menu enables access to mixing valve settings in the zone.

CZ

To set the I-time:

MENU TREE*

DE

1. Select I-time.

Mixing Valve Heating

2. Press the navigation wheel to confirm selection.

Cooling

3. Set the value.

P-area

Default: 35 seconds

I-time

Setting range: 5 – 300 seconds, 1 second increments

Actuator running time *

In this menu the I-time for the mixing valve regulation is set.

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

DK EE

4. Confirm the setting by pressing the navigation wheel again.

ES

A C T U AT O R R U N N I N G T I M E

HEATING This menu enables access to mixing valve settings in the zone while in heating mode. This menu is only shown if one of the following requirements are met:

In this menu the actuator running time for the mixing valve regulation is set.

FI

To set the actuator running time: 1. Select Actuator running time.

• System Type is set to 2 Pipe, Indoor Cooling Only is set to No, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone.

2. Press the navigation wheel to confirm selection.

Default: 120 seconds

• System Type is set to 4 Pipe, Z1&2 Operation Mode is set to Only Heating or Heating And Cooling, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone.

Setting range: 0 – 500 seconds, 1 second increments

FR

3. Set the value.

HR HU

4. Confirm the setting by pressing the navigation wheel again.

IT

MENU TREE

Heating

LT

P-area I-time Actuator running time

LV

P-AREA

In this menu the P-area for the mixing valve regulation is set.

NL

To set the P-area:

NO

1. Select P-area. 2. Press the navigation wheel to confirm selection.

PL

3. Set the value.

Default: 140.0 ˚C

Setting range: 2.0 – 500.0 ˚C, 0.1 ˚C increments

PT

4. Confirm the setting by pressing the navigation wheel again.

RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

93


UK I-TIME

COOLING

CZ

This menu enables access to mixing valve settings in the zone while in cooling mode.

DE

This menu is only shown if one of the following requirements are met:

DK

• System Type is set to 2 Pipe and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone. • System Type is set to 4 Pipe, Z1&2 Operation Mode is set to Only Cooling or Heating And Cooling, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone.

EE ES

MENU TREE

FR HR

2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 50 seconds

Setting range: 5 – 300 seconds, 1 second increments

4. Confirm the setting by pressing the navigation wheel again.

P-area I-time

To set the actuator running time:

Actuator running time

1. Select Actuator running time.

P-AREA

2. Press the navigation wheel to confirm selection.

In this menu the P-area for the mixing valve regulation is set.

3. Set the value.

1. Select P-area. 2. Press the navigation wheel to confirm selection.

IT

1. Select I-time.

In this menu the actuator running time for the mixing valve regulation is set.

To set the P-area:

HU

To set the I-time:

A C T U AT O R R U N N I N G T I M E

Cooling

FI

In this menu the I-time for the mixing valve regulation is set.

Default: 60 seconds

Setting range: 0 – 500 seconds, 1 second increments

4. Confirm the setting by pressing the navigation wheel again.

3. Set the value.

LT

Default: 200.0 ˚C

Setting range: 2.0 – 500.0 ˚C, 0.1 ˚C increments

4. Confirm the setting by pressing the navigation wheel again.

LV NL NO PL PT RO RU SE SK 94

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK P-AREA

ACTUATOR RUNNING TIME

In this menu the P-area for the mixing valve regulation is set.

In this menu the actuator running time for the mixing valve regulation is set.

CZ

This menu is only shown if Zone Setup is set to Domestic Hot Water for the zone.

This menu is only shown if Zone Setup is set to Domestic Hot Water for the zone.

DE

To set the P-area:

To set the actuator running time:

1. Select P-area.

1. Select Actuator running time.

2. Press the navigation wheel to confirm selection.

2. Press the navigation wheel to confirm selection.

3. Set the value.

3. Set the value.

Default: 70 ˚C

Default: 60 seconds

Setting range: 2.0 – 500.0 ˚C, 0.1 ˚C increments

Setting range: 0 – 300 seconds, 1 second increments

4. Confirm the setting by pressing the navigation wheel again.

DK EE ES

4. Confirm the setting by pressing the navigation wheel again.

FI

I-TIME In this menu the I-time for the mixing valve regulation is set.

FR

This menu is only shown if Zone Setup is set to Domestic Hot Water for the zone.

HR

To set the I-time: 1. Select I-time.

HU

2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 18 seconds

Setting range: 5 – 300 seconds, 1 second increments

IT LT

4. Confirm the setting by pressing the navigation wheel again.

LV NL NO PL PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

95


UK Dehumidifier Control

Seasonal Shut Off

CZ

This menu enables access to dehumidifier settings in the zone.

This menu enables access to seasonal shut off settings in the zone.

DE

This menu is only shown if Dehumidifier Control is enabled in the startup wizard for the zone.

This menu is only shown if Zone Setup is set to Stand Alone Control or Smatrix Base PRO.

MENU TREE

MENU TREE*

DK

Dehumidifier Control

EE

Seasonal Shut Off Dew Point Margin

Heating

Dead Zone

Cooling

DEW POINT MARGIN

ES

In this menu the dew point margin, for controlling the dehumidifier, in the zone can be set. The dehumidifier is started when the supply temperature is equal or lower than the dew point temperature + dew point margin. The dehumidifier is shut off when the supply temperature is equal or higher than the dew point temperature + dew point margin + deadzone temperature.

FI FR

To set the dew point margin:

HR

LT LV

HEATING This menu enables access to seasonal shut off settings in the zone, while in heating mode. This menu is only shown if one of the following requirements are met: • System Type is set to 2 Pipe, Indoor Cooling Only is set to No, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone.

3. Set the value.

Default: 4.0 ˚C

MENU TREE*

Setting range: -1.0 – 10.0 ˚C

2. Press the navigation wheel to confirm selection.

IT

Heating

4. Confirm the new setting by pressing the navigation wheel again.

Pump Stop

DEAD ZONE

Shut Off Outdoor Temp.

In this menu the dead zone (hysteresis) for when to shut off the dehumidifier in the zone can be set.

T. Outdoor Setpoint

Valve Close

T. Outdoor Delay Shut Off Indoor Temp.

To set the dead zone:

NL

1. Select Dead Zone. 2. Press the navigation wheel to confirm selection.

NO

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

• System Type is set to 4 Pipe, Z1&2 Operation Mode is set to Only Heating or Heating And Cooling, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone.

1. Select Dew Point Margin.

HU

*

T. Indoor Delay *

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

3. Set the value.

Default: 2.0 ˚C

PL

Setting range: 1.0 – 5.0 ˚C

PT

4. Confirm the new setting by pressing the navigation wheel again.

RO RU SE SK 96

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK PUMP STOP

T. O U T D O O R S E T P O I N T

In this menu a function to stop the circulation pump, when requirements are met, is enabled.

In this menu the outdoor temperature setpoint for stopping the circulation pump, and/or closing the mixing valve, in the zone is set.

CZ

This menu is only shown if Shut Off Outdoor Temp. is enabled.

DE

This menu is only shown if Zone Setup is set to Stand Alone Control, and Dehumidifier is set to Disable. To enable the function: 1. Select Pump Stop. 2. Press the navigation wheel to confirm selection. 3. Select Enable.

To set an outdoor temperature setpoint:

2. Press the navigation wheel to confirm selection.

Default: Disable

3. Select Enable.

Setting range: Disable/Enable

Default: 17.0 ˚C

Setting range: 0.0 – 40.0 ˚C, 0.1 ˚C increments

4. Confirm the setting by pressing the navigation wheel again. VA LV E C LO S E

In this menu a function to close the mixing valve, when requirements are met, is enabled. To enable the function: 1. Select Valve Close. 2. Press the navigation wheel to confirm selection. 3. Select Enable.

ES FI

T. O U T D O O R D E L AY

In this menu the time delay for how long the outdoor temperature must be equal or higher than T Outdoor Setpoint before stopping the circulation pump, and/or closing the mixing valve, in the zone is set.

FR HR

This menu is only shown if Shut Off Outdoor Temp. is enabled.

Default: Disable

To set the delay:

Setting range: Disable/Enable

1. Select T. Outdoor Delay.

4. Confirm the setting by pressing the navigation wheel again.

2. Press the navigation wheel to confirm selection.

S H U T O F F O U T D O O R T E M P.

Default: 24 h

Setting range: 0 – 24 h, 1 h increments

This menu is only shown if Pump Stop and/or Valve Close is enabled.

EE

4. Confirm the setting by pressing the navigation wheel again.

In this menu the function to stop the circulation pump and/or when to close the mixing valve, at an outdoor temperature setpoint is enabled/disabled for the zone.

DK

1. Select T Outdoor Setpoint.

HU IT

3. Set the value.

LT

4. Confirm the setting by pressing the navigation wheel again.

LV NL

To set an shut off outdoor temperature: 1. Select Shut Off Outdoor Temp..

NO

2. Press the navigation wheel to confirm selection. 3. Select Enable.

Default: Disable

Setting range: Disable/Enable

PL PT

4. Confirm the setting by pressing the navigation wheel again.

RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

97


UK CZ

S H U T O F F I N D O O R T E M P.

COOLING

In this menu the function to stop the circulation pump, and/or when to close the mixing valve, at an indoor temperature setpoint is enabled/disabled for the zone.

This menu enables access to seasonal shut off settings in the zone, while in cooling mode.

This menu is only shown if Pump Stop and/or Valve Close is enabled, and if Heating Mode is set to Outdoor + Indoor comp. for the zone.

DE DK

To set an shut off outdoor temperature: 1. Select Shut Off Outdoor Temp..

EE

2. Press the navigation wheel to confirm selection. 3. Select Enable.

ES

Default: Disable

Setting range: Disable/Enable

This menu is only shown if one of the following requirements are met: • System Type is set to 2 Pipe, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone.. • System Type is set to 4 Pipe, Z1&2 Operation Mode is set to Only Cooling or Heating And Cooling, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone.. MENU TREE*

Cooling

4. Confirm the setting by pressing the navigation wheel again.

FI

Pump Stop Valve Close

T . I N D O O R D E L AY

FR

T. Outdoor Setpoint

*

HR

In this menu the time delay for how long the indoor temperature must be equal or higher than the indoor setpoint before stopping the circulation pump, and/or closing the mixing valve, in the zone is set.

HU

This menu is only shown if Shut Off Indoor Temp. is enabled.

In this menu a function to stop the circulation pump, when requirements are met, is enabled.

To set the delay:

To enable the function:

1. Select T. Indoor Delay.

1. Select Pump Stop.

2. Press the navigation wheel to confirm selection.

2. Press the navigation wheel to confirm selection.

3. Set the value.

3. Select Enable.

Default: 0 h

Default: Disable

Setting range: 0 – 5 h, 1 h increments

Setting range: Disable/Enable

IT LT LV

4. Confirm the setting by pressing the navigation wheel again.

T. Outdoor Delay Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

PUMP STOP

4. Confirm the setting by pressing the navigation wheel again.

NL NO PL PT RO RU SE SK 98

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK VA LV E C LO S E

In this menu a function to close the mixing valve, when requirements are met, is enabled. To enable the function: 1. Select Valve Close. 2. Press the navigation wheel to confirm selection. 3. Select Enable.

Default: Disable

Setting range: Disable/Enable

H/C Switchover This menu enables access to settings related to switching between heating and cooling in the zone. This menu is only shown if System Type is set to 4 Pipe, Z1&2 Operation Mode (for Zone 1) is set to Only Heating or Only Cooling and Z1&2 Operation Mode (for Zone 2) is set to Heating And Cooling.

Outdoor Trigger Temp. Indoor Trigger Temp. Indoor Trigger Delay.

Hysteresis

1. Select T Outdoor Setpoint. 2. Press the navigation wheel to confirm selection.

H/C SWITCHOVER

3. Select Enable.

In this menu settings for switching the zone between heating and cooling is set.

T . O U T D O O R D E L AY

In this menu the time delay for how long the outdoor temperature must be equal or higher than T Outdoor Setpoint before stopping the circulation pump, and/or closing the mixing valve, in the zone is set.

1. Select H/C Switchover.

IT

2. Press the navigation wheel to confirm selection. 3. Select heating/cooling switchover function for the zone.

Setting range: 0 – 24 h, 1 h increments

4. Confirm the setting by pressing the navigation wheel again.

LT

• Indoor and Outdoor uses the indoor and outdoor temperatures and time delays to switch the zone between heating and cooling.

• Supply Water Temp. uses the supply water temperature and a hysteresis to switch the zone between heating and cooling.

NL

• Contact Input uses an external signal to switch the zone between heating and cooling.

NO

• Force Heating sets the zone in forced heating.

• Force Cooling sets the zone in forced cooling.

3. Set the value. Default: 24 h

HR HU

2. Press the navigation wheel to confirm selection.

FR

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

To select heating/cooling swithover function for the zone:

To set the delay: 1. Select T. Outdoor Delay.

FI

Supply Setpoint for HC Switch

*

4. Confirm the setting by pressing the navigation wheel again.

ES

Outdoor Trigger Delay

To set an outdoor temperature setpoint:

Setting range: 0.0 – 40.0 ˚C, 0.1 ˚C increments

EE

H/C Switchover

In this menu the outdoor temperature setpoint for stopping the circulation pump, and/or closing the mixing valve, in the zone is set.

DK

H/C Switchover

T. O U T D O O R S E T P O I N T

Default: 17.0 ˚C

DE

MENU TREE*

4. Confirm the setting by pressing the navigation wheel again.

CZ

LV

PL

4. Confirm the new setting by pressing the navigation wheel again.

PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

99


UK CZ

OUTDOOR TRIGGER TEMP.

INDOOR TRIGGER TEMP.

In this menu one of the triggers (outdoor temperature) for switching the zone between heating and cooling is set.

In this menu one of the triggers (indoor temperature) for switching the zone between heating and cooling is set.

DE

N OT E ! All triggers and time delays must be met for the zone to switch heating/cooling mode.

N OT E ! All triggers and time delays must be met for the zone to switch heating/cooling mode.

This menu is only shown if H/C Switchover is set to Indoor and Outdoor.

This menu is only shown if H/C Switchover is set to Indoor and Outdoor.

To set the outdoor trigger temperature:

To set the indoor trigger temperature:

1. Select Outdoor Trigger Temp.

1. Select Indoor Trigger Temp.

2. Press the navigation wheel to confirm selection.

2. Press the navigation wheel to confirm selection.

3. Set the value.

3. Set the value.

Default: 20.0 ˚C

Default: 22.0 ˚C

Setting range: 5.0 – 30.0 ˚C, 0.1 ˚C increments

Setting range: 5.0 – 30.0 ˚C, 0.1 ˚C increments

DK EE ES FI FR HR HU

4. Confirm the new setting by pressing the navigation wheel again.

4. Confirm the new setting by pressing the navigation wheel again.

OUTDOOR TRIGGER DELAY

INDOOR TRIGGER DELAY

In this menu one of the triggers (delay for outdoor temperature) for switching the zone between heating and cooling is set.

In this menu one of the triggers (delay for indoor temperature) for switching the zone between heating and cooling is set.

N OT E ! All triggers and time delays must be met for the zone to switch heating/cooling mode.

N OT E ! All triggers and time delays must be met for the zone to switch heating/cooling mode.

This menu is only shown if H/C Switchover is set to Indoor and Outdoor.

This menu is only shown if H/C Switchover is set to Indoor and Outdoor.

To set the outdoor trigger delay:

To set the indoor trigger delay:

1. Select Outdoor Trigger Delay.

1. Select Indoor Trigger Delay.

2. Press the navigation wheel to confirm selection.

2. Press the navigation wheel to confirm selection.

3. Set the value.

3. Set the value.

Default: 24 h

Default: 24 h

Setting range: 1 – 48 h, 1 h increments

Setting range: 1 – 48 h, 1 h increments

IT LT LV NL NO

4. Confirm the new setting by pressing the navigation wheel again.

4. Confirm the new setting by pressing the navigation wheel again.

PL PT RO RU SE SK 100

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK SUPPLY SETPOINT FOR HC SWITCH

HYSTERESIS

In this menu the supply temperature setpoint for switching between heating and cooling is set.

In this menu the hysteresis which is used to switch between heating and cooling using Supply Setpoint for HC Switch is set.

CZ

To set the hysteresis:

DE

The zone switches to heating when the supply temperature is higher than Supply Setpoint for HC Switch. The zone switches back when the supply temperature is lower than Supply Setpoint for HC Switch - Hysteresis. The zone switches to cooling when the supply temperature is lower than Supply Setpoint for HC Switch. The zone switches back when the supply temperature is lower than Supply Setpoint for HC Switch + Hysteresis.

1. Select Hysteresis.

DK

2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 2 ˚C

Setting range: 0 – 4 ˚C, 1 ˚C increments

EE

4. Confirm the new setting by pressing the navigation wheel again.

ES

N OT E ! When using this switch mode, the heating/ cooling switch is done in the heat pump/ chiller. The Move PRO controller switches the operation mode when it detects the change in supply temperture.

FI FR

No diverting valves are controlled in this mode.

HR

This menu is only shown if H/C Switchover is set to Supply Water Temp..

HU

To set the supply temperature setpoint for HC switch: 1. Select Supply Setpoint for HC Switch.

IT

2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 18 ˚C

Setting range: 5 – 30 ˚C, 1 ˚C increments

LT LV

4. Confirm the new setting by pressing the navigation wheel again.

NL NO PL PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

101


UK Condensation Delay In this menu the condensation delay in the zone is set. If condensation is not detected (by the condensation sensor in the zone) during the time set in the delay, the condensation status (in the zone information menu) switches to No.

CZ DE

Z one 3 S ettings In this menu parameter settings for zone 3 can be set or changed. Menu tree* Zone 3 Settings Supply Temp. Settings

This menu is only shown if Condensation Sensor is enabled in the startup wizard for the zone.

DK

Heating Indoor Temp. Settings

To set the condensation delay:

EE

Comf. - ECO

1. Select Condensation Delay.

ES FI

Heating Curve

2. Press the navigation wheel to confirm selection.

Cooling Curve

3. Set the value.

Meltaway Curve (IDLE Status)

Default: 10 min

Setting range: 0 – 120 min, 1 min increments

Return Temperature Enter Stop State Conditions

4. Confirm the new setting by pressing the navigation wheel again.

Enter Idle State Conditions Enter Melting State Conditions

FR

Manual Operation Pump

HR

Mixing Valve Dehumidifier Control

HU

Seasonal Shut Off H/C Switchover Automatic Freeze Protection

IT

Condensation Delay *

LT

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

LV NL NO PL PT RO RU SE SK 102

U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Supply Temp. Settings

C A L C U L AT E D S U P P LY S E T P O I N T

This menu enables access to settings related to the supply temperature in the zone.

In this menu the calculated supply setpoint for the zone can be overidden. This temperature is used as setpoint for the supply temperature.

CZ

To override the calculated supply setpoint:

DE

MENU TREE* Supply Temp. Settings Heating Cooling

2. Press the navigation wheel to confirm selection.

Calculated Supply Setpoint

3. Select Manual.

Melting Supply Setpoint

4. Set the override value.

Heating Curve Meltaway

IDLE Supply Setpoint Min. Supply Temp. (IDLE Status) Max. Supply Temp. (IDLE Status) *

1. Select Calculated supply setpoint.

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

5. Confirm the new setting by pressing the navigation wheel again. H E AT I N G M I N . S U P P LY T E M P.

This menu enables access to settings related to the heating supply temperature in the zone.

1. Select Heating Min. supply temp.

• System Type is set to 4 Pipe, Z3 Operation Mode is set to Only Heating or Heating And Cooling, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone. MENU TREE

Heating Calculated Supply Setpoint

FI FR HR

2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 15.0 ˚C

Setting range: 5.0 – 35.0 ˚C (or max. supply temp), 0.1 ˚C increments

HU IT

4. Confirm the new setting by pressing the navigation wheel again. H E AT I N G M A X . S U P P LY T E M P.

LT

In this menu the maximum allowed supply temperature for the zone can be set. The supply temperature is not allowed to rise above this value.

LV

To set the maximum allowed supply temperature:

Heating Min. Supply Temp.

1. Select Heating Max. supply temp.

Heating Max. Supply Temp.

2. Press the navigation wheel to confirm selection.

Deviation alarm limit

3. Set the value.

Deviation alarm delay

ES

In this menu the minimum allowed supply temperature for the zone can be set. The supply temperature is not allowed to fall below this value. To set the minimum allowed supply temperature:

• System Type is set to 2 Pipe, Indoor Cooling Only is set to No, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone.

EE

Setting range: -5.0 – 70.0 ˚C, 0.1 ˚C increments

HEATING

This menu is only shown if one of the following requirements are met:

DK

Default: 70.0 ˚C

Setting range: 5.0 (or min. supply temp) – 70.0 ˚C, 0.1 ˚C increments

NL NO PL

4. Confirm the new setting by pressing the navigation wheel again.

PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

103


UK D E V I AT I O N A L A R M L I M I T

In this menu the deviation alarm limit for the supply temperature in the zone is set. If the difference between the measured and the calculated supply temperatures are higher than the set limit during the time set in Deviation alarm delay, the alarm is triggered.

CZ DE

To set the deviation alarm limit:

DK

1. Select Deviation alarm limit. 2. Press the navigation wheel to confirm selection.

EE

3. Set the value.

ES

Default: 10.0 ˚C

Setting range: 0.0 – 50.0 ˚C, 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again.

FI

COOLING This menu enables access to settings related to the cooling supply temperature in the zone. This menu is only shown if one of the following requirements are met: • System Type is set to 2 Pipe, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone. • System Type is set to 4 Pipe, Z3 Operation Mode is set to Only Cooling or Heating And Cooling, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone. MENU TREE

Cooling Calculated Supply Setpoint

D E V I AT I O N A L A R M D E L AY

Cooling Min. Supply Temp.

In this menu the deviation alarm delay for the deviation alarm limit in the zone is set. If the difference between the measured and the calculated supply temperatures are higher than Deviation alarm limit during the set delay, the alarm is triggered.

FR HR

To set the deviation alarm delay: 1. Select Deviation alarm delay.

HU

2. Press the navigation wheel to confirm selection. 3. Set the value.

IT LT

Dew Point Margin Dew Point Offset C A L C U L AT E D S U P P LY S E T P O I N T

In this menu the calculated supply setpoint for the zone can be overidden. This temperature is used as setpoint for the supply temperature. To override the calculated supply setpoint:

Default: 5 min

1. Select Calculated supply setpoint.

Setting range: 0 – 30 min, 1 min increments

2. Press the navigation wheel to confirm selection.

4. Confirm the new setting by pressing the navigation wheel again.

LV

Cooling Max. Supply Temp.

3. Select Manual. 4. Set the override value.

Setting range: -5.0 – 70.0 ˚C, 0.1 ˚C increments

5. Confirm the new setting by pressing the navigation wheel again.

NL NO PL PT RO RU SE SK 104

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK C O O L I N G M I N . S U P P LY T E M P.

DEW POINT MARGIN

In this menu the minimum allowed supply temperature for the zone can be set. The supply temperature is not allowed to fall below this value.

In this menu the dew point margin for the zone can be set. The dew point temperature is calculated using the current room temperature and relative humidity.

To set the minimum allowed supply temperature:

When the calculated supply temperature is lower than the dew point temperature + Dew Point Offset this value is added to the calculated supply temperature.

DE

To set the dew point margin:

DK

1. Select Cooling Min. supply temp. 2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 8.0 ˚C

Setting range: 5.0 – 40.0 ˚C (or max. supply temp), 0.1 ˚C increments

1. Select Dew Point Margin.

3. Set the value.

Default: 4.0 ˚C

Setting range: -1.0 – 10.0 ˚C

C O O L I N G M A X . S U P P LY T E M P.

4. Confirm the new setting by pressing the navigation wheel again.

To set the maximum allowed supply temperature: 1. Select Cooling Max. supply temp. 2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 25.0 ˚C

Setting range: 5.0 (or min. supply temp) – 40.0 ˚C, 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again.

EE

2. Press the navigation wheel to confirm selection.

4. Confirm the new setting by pressing the navigation wheel again. In this menu the maximum allowed supply temperature for the zone can be set. The supply temperature is not allowed to rise above this value.

CZ

ES FI

DEW POINT OFFSET

FR

In this menu the dew point offset for the zone can be set. The dew point temperature is calculated using the current room temperature and relative humidity.

HR

The offset is used together with the dew point temperature to decide when to increase the calculated supply temperature with the value set in Dew Point Margin.

HU

To set the dew point offset:

IT

1. Select Dew Point Offset. 2. Press the navigation wheel to confirm selection.

LT

3. Set the value.

Default: 1.0 ˚C

Setting range: 0.0 – 4.0 ˚C

LV

4. Confirm the new setting by pressing the navigation wheel again.

NL NO PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

105


UK CALCULATED SUPPLY SETPOINT

HEATING CURVE MELTAWAY

CZ

In this menu the calculated supply setpoint for the zone can be overidden. This temperature is used as setpoint for the supply temperature.

In this menu a heating curve for the zone, while meltaway status is IDLE, can be enabled.

DE

This menu is only shown if Zone Setup is set to Meltaway for the zone.

DK

To override the calculated supply setpoint: 1. Select Calculated supply setpoint. 2. Press the navigation wheel to confirm selection.

EE

3. Select Manual.

ES

This menu is only shown if Zone Setup is set to Meltaway for the zone. To enable the heating curve: 1. Select Heating Curve. 2. Press the navigation wheel to confirm selection. 3. Select Enable.

4. Set the override value.

4. Confirm the new setting by pressing the navigation wheel again.

IDLE SUPPLY SETPOINT

Setting range: -5.0 – 70.0 ˚C, 0.1 ˚C increments

5. Confirm the new setting by pressing the navigation wheel again. MELTING SUPPLY SETPOINT

In this menu a setpoint for the zone, while meltaway status is IDLE, can be set. This temperature is used as setpoint for the supply temperature.

FR

In this menu the supply temperature setpoint for meltaway in the zone is set.

This menu is only shown if Zone Setup is set to Meltaway for the zone.

HR

This menu is only shown if Zone Setup is set to Meltaway for the zone.

To set the IDLE supply setpoint:

To set the melting supply temperature setpoint:

2. Press the navigation wheel to confirm selection.

1. Select Supply Setpoint.

3. Set the override value.

2. Press the navigation wheel to confirm selection.

Default: 8.0 ˚C

3. Set the value.

Setting range: 1.0 – 15.0 ˚C, 0.1 ˚C increments

Default: 35 ˚C

Setting range: 5.0 – 35.0 ˚C, 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again.

FI

HU IT LT

1. Select IDLE supply setpoint.

4. Confirm the new setting by pressing the navigation wheel again.

LV NL NO PL PT RO RU SE SK 106

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK MIN. SUPPLY TEMP. (IDLE STATUS)

Heating Indoor Temp. Settings

In this menu the minimum available supply temperature for the zone, while meltaway status is IDLE, can be set. The supply temperature is not allowed to fall below this value.

This menu enables access to settings related to the room temperature sensor in the zone.

CZ

This menu and its submenus are only shown if Heating Mode is set to Outdoor + Indoor comp..

DE

This menu is only shown if Zone Setup is set to Meltaway for the zone.

MENU TREE*

DK

Heating Indoor Temp. Settings

To set the minimum allowed supply temperature: 1. Select Min. supply temp.

Indoor Setpoint

2. Press the navigation wheel to confirm selection.

Calculated Indoor Setpoint

3. Set the value.

ECO-Comf. Status

Default: 5.0 ˚C

Indoor Setpoint Influence (Lower)

Setting range: 0.0 – 25.0 ˚C, 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again. MAX. SUPPLY TEMP. (IDLE STATUS) In this menu the maximum available supply temperature for the zone, while meltaway status is IDLE, can be set. The supply temperature is not allowed to rise above this value. This menu is only shown if Zone Setup is set to Meltaway for the zone.

ES

Indoor Setpoint Influence (Upper) *

FI

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

FR

INDOOR SETPOINT In this menu the indoor temperature setpoint for the zone is set.

HR

This information is only shown if Zone Setup is set to Stand Alone Control for the zone.

HU

To set the indoor temperature setpoint:

To set the minimum allowed supply temperature:

1. Select Indoor Setpoint.

1. Select Max. supply temp.

2. Press the navigation wheel to confirm selection.

2. Press the navigation wheel to confirm selection.

3. Set the value.

3. Set the value.

Default: 21.0 ˚C

Default: 15.0 ˚C

Setting range: 5.0 – 35.0 ˚C, 0.1 ˚C increments

Setting range: 0.0 – 70.0 ˚C, 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again.

4. Confirm the new setting by pressing the navigation wheel again.

EE

IT LT LV

CALCULATED INDOOR SETPOINT

NL

This menu shows the calculated indoor setpoint for the zone.

NO

This information is only shown if Zone Setup is set to Stand Alone Control and if ECO-Comf mode is set to ECO for the zone.

PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

107


UK CZ

ECO-COMF STATUS

INDOOR SETPOINT INFLUENCE (UPPER)

This menu shows if the zone is set in ECO mode.

In this menu the indoor setpoint influence (upper) is set. If the measured indoor temperature is lower than the indoor temperature setpoint, the supply temperature sepoint will be increased using this value.

This information is only shown if ECO-Comf mode is set to ECO for the zone.

DE

INDOOR SETPOINT INFLUENCE (LOWER) In this menu the indoor setpoint influence (lower) is set. If the measured indoor temperature is higher than the indoor temperature setpoint, the supply temperature sepoint will be lowered using this value.

DK EE

This menu is used to to keep the measured room temperature as close as possible to the indoor temperature setpoint.

ES

N OT E ! If the value is set too high it can lead to the system being unstable and the room temperature will start fluctuating.

FI FR HR

N OT E ! If the value is set too high it can lead to the system being unstable and the room temperature will start fluctuating. To set the indoor setpoint influence (upper): 1. Select Indoor Setpoint Influence (Upper). 2. Press the navigation wheel to confirm selection. 3. Set the value.

To set the indoor setpoint influence (lower):

Default: 4.0 ˚C

1. Select Indoor Setpoint Influence (Lower).

Setting range: 0.0 – 10.0 ˚C, 0.1 ˚C increments

2. Press the navigation wheel to confirm selection.

4. Confirm the new setting by pressing the navigation wheel again.

3. Set the value.

HU

This menu is used to to keep the measured room temperature as close as possible to the indoor temperature setpoint.

Default: 4.0 ˚C

Setting range: 0.0 – 10.0 ˚C, 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again.

IT LT LV NL NO PL PT RO RU SE SK 108

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Comf. - ECO

To edit/create the ECO-Comf Schedule:

This menu enables access to settings related to the controller Comfort/ECO modes.

1. Select ECO-Comf Schedule.

This menu and its submenus are only shown if Zone Setup is set to Stand Alone Control and if Heating Mode is set to Outdoor + Indoor comp. for the zone.

CZ

2. Press the navigation wheel to confirm selection.

The current schedule is showing.

DE

3. Select a day. 4. Press the navigation wheel to confirm selection.

MENU TREE

Comf. - ECO ECO Setback ECO-Comf Status ECO-Comf Schedule

ECO SETBACK In this menu the ECO setback temperature is set. The parameter reduces the current setpoint with the set value. If the setback is set to 0 the zone will resume its normal operation, even if it is set in ECO mode. To set the ECO setback value: 1. Select ECO Setback. 2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 4.0 ˚C

Setting range: 0.0 – 10.0 ˚C, 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again. ECO-COMF STATUS This menu shows if the zone is set in ECO or Comf (comfort) mode. ECO-COMF SCHEDULE In this menu a schedule for switching between Comfort and ECO mode can be created. The default schedule is set to Comfort mode 24h a day, 7 days a week.

W arning ! Ensure that different schedules cannot enable ECO and Comf and the same time. This may cause an error where the controller must be reset to factory default values.

DK

All current schedule settings are shown, each line representing a switch between Comfort and ECO mode. If entering the menu for the first time only one line is present, showing Comf starting at 00:00 every day of the week.

EE ES

5. Select an existing line to edit or 00:00 Add new to add a new setting.

FI

6. Select wether to edit the hours, minutes, mode or day of the week. HOURS: Set at which hour the mode will start and press the navigation wheel to confirm selection.

FR

MINUTES: Set at which minte of the hour the mode will start and press the navigation wheel to confirm selection.

HR HU

MODE: Select a mode which should start at the set time and press the navigation wheel to confirm selection. Select between Comf, ECO and Delete switch time. Delete switch time erases the current line when selecting OK and pressing the navigation wheel.

IT LT

DAY OF THE WEEK:

Select which days of the week, at the set time the selected mode should start.

LV

7. Select OK at the end of the line, when done, and press the navigation wheel to confirm selection.

NL

A new line has been added to the schedule.

NO

8. Redo steps 5 and 6 until the schedule is complete. 9. Press the back button on the controller to exit the schedule setup.

PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

109


UK Heating Curve

OFFSET

CZ

This menu enables access to heating curve settings for the zone. Settings such as the slope (Setting) and offset of the heating curve.

In this menu the the heating curve can be offset. The offset can be used for temporary changes to the heating curve.

DE

This menu is only shown if one of the following requirements are met:

To offset the heating curve:

DK

• System Type is set to 2 Pipe, Indoor Cooling Only is set to No, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone.

EE

• System Type is set to 4 Pipe, Z1&2 Operation Mode is set to Only Heating or Heating And Cooling, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone.

ES

MENU TREE

FI

1. Select Offset. 2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 0

Setting range: -8 – 8, 1 increments

4. Confirm the new setting by pressing the navigation wheel again. HEATING CURVE

Heating Curve Setting

This menu shows the heating curve, and max/min supply temperature limits, for the zone.

Offset

FR

Heating Curve

SETTING

HR

In this menu the slope of the heating curve is selected. To select a heating curve:

HU

1. Select Setting. 2. Press the navigation wheel to confirm selection.

IT

3. Set the value.

LT

Default: 0.9

Setting range: 0.1 – 1.6, 0.1 increments

4. Confirm the new setting by pressing the navigation wheel again.

LV NL NO PL PT RO RU SE SK 110

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Cooling Curve

OFFSET

This menu enables access to cooling curve settings for the zone. Settings such as the slope (Setting) and offset of the heating curve.

In this menu the the heating curve can be offset. The offset can be used for temporary changes to the heating curve.

CZ

This menu is only shown if one of the following requirements are met:

To offset the heating curve:

DE

• System Type is set to 2 Pipe and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone. • System Type is set to 4 Pipe, Z1&2 Operation Mode is set to Only Cooling or Heating And Cooling, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone. MENU TREE

1. Select Offset.

DK

2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 0

Setting range: -8 – 8, 1 increments

EE

4. Confirm the new setting by pressing the navigation wheel again.

ES

COOLING CURVE

Cooling Curve Setting

FI

This menu shows the cooling curve, and max/min supply temperature limits, for the zone.

Offset

FR

Cooling Curve

SETTING

HR

In this menu the slope of the heating curve is selected. To select a heating curve:

HU

1. Select Setting. 2. Press the navigation wheel to confirm selection.

IT

3. Set the value.

Default: 0.2

Setting range: 0.1 – 1.6, 0.1 increments

LT

4. Confirm the new setting by pressing the navigation wheel again.

LV NL NO PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

111


UK Meltaway Curve (IDLE Status)

OFFSET In this menu the the meltaway heating curve can be offset. The offset can be used for temporary changes to the heating curve.

DE

This menu enables access to meltaway heating curve settings for the zone while in IDLE status. Settings such as the slope (Setting) and offset of the meltaway heating curve.

DK

This menu is only shown if Zone Setup is set to Meltaway and if Heating Curve Meltaway is enabled for the zone.

CZ

Meltaway Curve (IDLE Status) Setting

ES

Offset Heating Curve

FI

SETTING In this menu the slope of the meltaway heating curve is selected.

FR

1. Select Offset. 2. Press the navigation wheel to confirm selection. 3. Set the value.

MENU TREE

EE

To offset the meltaway heating curve:

Default: 0

Setting range: -8 – 8, 1 increments

4. Confirm the new setting by pressing the navigation wheel again. HEATING CURVE This menu shows the meltaway heating curve, and max/ min supply temperature limits, for the zone.

To select a meltaway heating curve:

HR

1. Select Setting. 2. Press the navigation wheel to confirm selection.

HU

3. Set the value.

IT

Default: 0.9

Setting range: 0.1 – 1.6, 0.1 increments

4. Confirm the new setting by pressing the navigation wheel again.

LT LV NL NO PL PT RO RU SE SK 112

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Return Temperature

Enter Stop State Conditions

This menu enables access to settings related to the return temperature sensor.

This menu enables access to parameters deciding when to switch the meltaway state in the zone between IDLE and STOP.

CZ

The zone switches from IDLE to STOP state when the measured outdoor temperature is higher than the value set in Outdoor Temperature, for the number of days set in Delay (days).

DE

This menu is only shown if Zone Setup is set to Meltaway for the zone. MENU TREE Return Temperature Max. Supply-Return Diff.

MAX. SUPPLY-RETURN DIFF. In this menu the maximum difference allowed between the supply and return temperature is set.

This menu is only shown if Zone Setup is set to Meltaway for the zone.

Enter Stop State Conditions

ES Outdoor Temperature Delay (days)

1. Select Max. Supply-Return Diff.. 2. Press the navigation wheel to confirm selection.

OUTDOOR TEMPERATURE

3. Set the value.

In this menu the outdoor temperature, used to switch meltaway state between IDLE and STOP, is set.

Default: 20 ˚C

Setting range: 0.0 – 80.0 ˚C, 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again.

EE

MENU TREE

To set the return temperature setpoint:

DK

FI FR

To set the outdoor temperature:

HR

1. Select Outdoor Temperature. 2. Press the navigation wheel to confirm selection.

HU

3. Set the value.

Default: 10.0 ˚C

Setting range: 0.0 – 15.0 ˚C, 0.1 ˚C increments

IT

4. Confirm the new setting by pressing the navigation wheel again.

LT

DELAY (DAYS) In this menu the number of delay days, used to switch meltaway state between IDLE and STOP, is set.

LV

To set the delay:

NL

1. Select Delay (days). 2. Press the navigation wheel to confirm selection.

NO

3. Set the value.

Default: 2 days

Setting range: 0 – 5 days, 1 day increments

PL

4. Confirm the new setting by pressing the navigation wheel again.

PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

113


UK CZ DE DK EE ES

Enter Idle State Conditions

DELAY (HOURS)

This menu enables access to parameters used when to switch the meltaway state in the zone to and from IDLE.

In this menu the number of delay hours, used to switch meltaway state from STOP to IDLE, is set.

The zone switches from STOP to IDLE state when the measured outdoor temperature is lower than the value set in Outdoor Temperature, for the number of hours set in Delay (hours).

To set the delay:

The zone switches from MELTING to IDLE state when no moisture has been detected (for the number of days set in Delay Surface Dry), when the outdoor temperature is higher than the value set in Outdoor Temperature, and when the ground temperature is higher than Enter Melting State Conditions > Ground Temperature Limit.

3. Set the value.

This menu is only shown if Zone Setup is set to Meltaway for the zone.

FI

MENU TREE

FR

Delay (hours) Delay Surface Dry

IT

Default: 1 hour

Setting range: 0 – 24 hours, 1 hour increments

4. Confirm the new setting by pressing the navigation wheel again. DELAY SURFACE DRY In this menu the number of delay days, used to switch meltaway state from MELTING to IDLE, is set.

1. Select Delay Surface Dry. Outdoor Temperature

HU

2. Press the navigation wheel to confirm selection.

To set the dry surface delay:

Enter Idle State Conditions

HR

1. Select Delay (hours).

2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 0 days

OUTDOOR TEMPERATURE

Setting range: 0 – 2 days, 1 day increments

In this menu the outdoor temperature, used to switch meltaway state from STOP or MELTING to IDLE, is set.

4. Confirm the new setting by pressing the navigation wheel again.

To set the outdoor temperature: 1. Select Outdoor Temperature.

LT

2. Press the navigation wheel to confirm selection. 3. Set the value.

LV NL

Default: 5.0 ˚C

Setting range: 0.0 – 15.0 ˚C, 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again.

NO PL PT RO RU SE SK 114

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Enter Melting State Conditions

GROUND TEMPERATURE LIMIT

This menu enables access to parameters used when to switch the meltaway state in the zone to and from MELTING. When entering MELTING state the zone stays in that condition until the min limit set in Min. Time in Melting is met.

In this menu the ground temperature limit, used to switch meltaway state between IDLE to MELTING , is set.

CZ

To set the ground temperature limit:

DE

The zone switches from IDLE to MELTING state when one of the following scenarios are met: 1. No ground moisture is detected and the measured ground temperature is lower than than the set limit in Ground Temperature Limit. 2. No ground moisture is detected and the measured outdoor temperature is lower than than the set limit in Outdoor Temperature Low Limit. The zone switches from PROTECTION to MELTING when the primary return sensor measures a supply temperature that is higher than PRIMARY RETURN TEMP. HIGH, set in Automatic Freeze Protection . This menu is only shown if Zone Setup is set to Meltaway for the zone.

1. Select Ground Temperature Limit.

DK

2. Press the navigation wheel to confirm selection. 3. Select Low Limit.

EE

4. Press the navigation wheel to confirm selection. 5. Set the value.

Default: 2 ˚C

Setting range: 0 – 10 ˚C, 1 ˚C increments

ES

6. Confirm the new setting by pressing the navigation wheel again.

FI

OUTDOOR TEMP. OFFSET

FR

In this menu the outdoor temperature offset, used to switch meltaway state from IDLE to MELTING, is set. To set the outdoor temperature offset:

MENU TREE

HR

1. Select Outdoor Temp. Offset.

Enter Melting State Conditions

2. Press the navigation wheel to confirm selection. Ground Temperature Limit

3. Set the value.

Outdoor Temp. Offset

Default: 1 ˚C

Outdoor Temperature Low Limit

Setting range: -5 – 5 ˚C, 1 ˚C increments

Min. Time in Melting

4. Confirm the new setting by pressing the navigation wheel again.

HU IT LT LV NL NO PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

115


UK CZ DE

OUTDOOR TEMPERATURE LOW LIMIT

Manual Operation

In this menu the lower outdoor temperature limit, used to switch meltaway state from IDLE to MELTING, is set.

This menu enables access to manual operation mode in the zone.

To set the lower outdoor temperature limit:

When manual operation mode is activated, access to manual control (override) of the circulation pump and mixing valve is enabled.

1. Select Outdoor Temperature Low Limit. 2. Press the navigation wheel to confirm selection.

DK

3. Set the value.

EE

Default: 1 ˚C

Setting range: -5 – 5 ˚C, 1 ˚C increments

Menu tree* Manual Operation Manual Mode Pump

4. Confirm the new setting by pressing the navigation wheel again.

ES

MIN. TIME IN MELTING In this menu the minimum number of hours the zone can be in meltaway state MELTING, is set.

FI

To set the minimum time:

FR

1. Select Min. Time in Melting. 2. Press the navigation wheel to confirm selection.

HR

3. Set the value.

HU

Default: 2 hour

Setting range: 0 – 10 hours, 1 hour increments

4. Confirm the new setting by pressing the navigation wheel again.

IT LT

Mixing valve *

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

To activate manual operation mode: 1. Select Manual Mode. 2. Press the navigation wheel to confirm selection. 3. Select On. 4. Confirm the new setting by pressing the navigation wheel again. PUMP In this menu the pump can be overidden and turned on or off manually. This menu is only shown if Zone Setup is set to Stand Alone Control or Meltaway, Dehumidifier is set to Disable, and Manual Mode is set to On. To override the circulation pump operation: 1. Select Pump.

LV

2. Press the navigation wheel to confirm selection. 3. Select Manual.

NL

4. Select On.

NO

Default: Off

Setting range: Off/On

5. Confirm the new setting by pressing the navigation wheel again.

PL PT RO RU SE SK 116

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK MIXING VALVE

Pump

In this menu the mixing valve can be overriden opened or closed manually.

This menu enables access to pump settings in the zone.

CZ

This menu is only shown if Zone Setup is set to Stand Alone Control or Meltaway, and if Dehumidifier is disabled for the zone.

DE

This menu is only shown if Manual Mode is set to On. To override the mixing valve setting: 1. Select Mixing valve.

MENU TREE*

Pump Exercise

3. Select Manual.

Exercise Day of the Week

4. Set the override value.

Default: 0 %

Setting range: 0 – 100 %, 1 % increments.

5. Confirm the new setting by pressing the navigation wheel again.

DK

Pump

2. Press the navigation wheel to confirm selection.

EE

Exercise Hour Exercise Min *

ES

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

PUMP EXERCISE

FI

In this menu pump exercise can be activated. To activate pump exercise:

FR

1. Select Pump Exercise. 2. Press the navigation wheel to confirm selection.

HR

3. Select Pump Exercise.

Default: No Exercise

Setting range: No Exercise/Pump Exercise

HU

4. Confirm the new setting by pressing the navigation wheel again.

IT

EXERCISE DAY OF THE WEEK In this menu the day of the week for pump exercise is set.

LT

This menu is only shown if Pump Exercise is set to Pump Exercise.

LV

To select a day of the week for pump exercise:

NL

1. Select Exercise Day of the Week. 2. Press the navigation wheel to confirm selection.

NO

3. Select a day.

Setting range: Monday – Sunday

4. Confirm the setting by pressing the navigation wheel again.

PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

117


UK EXERCISE HOUR

Mixing Valve

CZ

In this menu the hour of the day for pump exercise is set.

This menu enables access to mixing valve settings in the zone.

DE

This menu is only shown if Pump Exercise is set to Pump Exercise.

MENU TREE* Mixing Valve

To select an hour of the day for pump exercise:

DK EE

Heating

1. Select Exercise Hour.

Cooling

2. Press the navigation wheel to confirm selection.

P-area I-time

3. Set the value.

ES

Default: 8 h

Setting range: 0 – 23 h, 1 h increments

4. Confirm the setting by pressing the navigation wheel again.

FI FR HR

In this menu the minute of the hour for pump exercise is set.

This menu is only shown if one of the following requirements are met:

This menu is only shown if Pump Exercise is set to Pump Exercise.

• System Type is set to 2 Pipe, Indoor Cooling Only is set to No, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone.

2. Press the navigation wheel to confirm selection. 3. Set the value.

LT

HEATING This menu enables access to mixing valve settings in the zone while in heating mode.

1. Select Exercise Min.

IT

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

EXERCISE MIN

To select a minute of the hour for pump exercise:

HU

Actuator running time *

Default: 0 min

Setting range: 0 – 59 min, 1 min increments

4. Confirm the setting by pressing the navigation wheel again.

• System Type is set to 4 Pipe, Z1&2 Operation Mode is set to Only Heating or Heating And Cooling, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone. MENU TREE

Heating P-area I-time Actuator running time

LV NL NO PL PT RO RU SE SK 118

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK P-AREA

In this menu the P-area for the mixing valve regulation is set. To set the P-area: 1. Select P-area. 2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 140.0 ˚C

Setting range: 2.0 – 500.0 ˚C, 0.1 ˚C increments

COOLING This menu enables access to mixing valve settings in the zone while in cooling mode.

CZ

This menu is only shown if one of the following requirements are met:

DE

• System Type is set to 2 Pipe and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone.

DK

4. Confirm the setting by pressing the navigation wheel again.

• System Type is set to 4 Pipe, Z1&2 Operation Mode is set to Only Cooling or Heating And Cooling, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone.

I-TIME

MENU TREE

In this menu the I-time for the mixing valve regulation is set.

1. Select I-time.

Actuator running time

2. Press the navigation wheel to confirm selection.

P-AREA

3. Set the value.

In this menu the P-area for the mixing valve regulation is set.

Setting range: 5 – 300 seconds, 1 second increments

4. Confirm the setting by pressing the navigation wheel again.

Default: 200.0 ˚C

Setting range: 2.0 – 500.0 ˚C, 0.1 ˚C increments

1. Select Actuator running time.

4. Confirm the setting by pressing the navigation wheel again.

2. Press the navigation wheel to confirm selection.

I-TIME

3. Set the value.

In this menu the I-time for the mixing valve regulation is set.

Setting range: 0 – 500 seconds, 1 second increments

4. Confirm the setting by pressing the navigation wheel again.

HU

2. Press the navigation wheel to confirm selection.

In this menu the actuator running time for the mixing valve regulation is set.

Default: 120 seconds

HR

1. Select P-area.

3. Set the value.

FR

To set the P-area:

A C T U AT O R R U N N I N G T I M E

To set the actuator running time:

FI

P-area I-time

Default: 35 seconds

ES

Cooling

To set the I-time:

EE

IT LT LV NL

To set the I-time: 1. Select I-time.

NO

2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 50 seconds

Setting range: 5 – 300 seconds, 1 second increments

PL PT

4. Confirm the setting by pressing the navigation wheel again.

RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

119


UK A C T U AT O R R U N N I N G T I M E

In this menu the actuator running time for the mixing valve regulation is set.

CZ

To set the actuator running time:

DE DK EE

This menu is only shown if Zone Setup is set to Meltaway for the zone.

2. Press the navigation wheel to confirm selection.

To set the I-time:

3. Set the value.

1. Select I-time.

Default: 60 seconds

2. Press the navigation wheel to confirm selection.

Setting range: 0 – 500 seconds, 1 second increments

3. Set the value.

P-AREA In this menu the P-area for the mixing valve regulation is set.

FI

This menu is only shown if Zone Setup is set to Meltaway for the zone.

FR

To set the P-area:

HR HU IT

Default: 50 seconds

Setting range: 5 – 300 seconds, 1 second increments

4. Confirm the setting by pressing the navigation wheel again. ACTUATOR RUNNING TIME In this menu the actuator running time for the mixing valve regulation is set.

1. Select P-area.

This menu is only shown if Zone Setup is set to Meltaway for the zone.

2. Press the navigation wheel to confirm selection.

To set the actuator running time:

3. Set the value.

1. Select Actuator running time.

Default: 200.0 ˚C

2. Press the navigation wheel to confirm selection.

Setting range: 2.0 – 500.0 ˚C, 0.1 ˚C increments

3. Set the value.

4. Confirm the setting by pressing the navigation wheel again.

LT

In this menu the I-time for the mixing valve regulation is set.

1. Select Actuator running time.

4. Confirm the setting by pressing the navigation wheel again.

ES

I-TIME

Default: 60 seconds

Setting range: 0 – 500 seconds, 1 second increments

4. Confirm the setting by pressing the navigation wheel again.

LV NL NO PL PT RO RU SE SK 120

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Dehumidifier Control

Seasonal Shut Off

This menu enables access to dehumidifier settings in the zone.

This menu enables access to seasonal shut off settings in the zone.

CZ

This menu is only shown if Dehumidifier Control is enabled in the startup wizard for the zone.

This menu is only shown if Zone Setup is set to Stand Alone Control or Smatrix Base PRO.

DE

MENU TREE

MENU TREE*

Dehumidifier Control

DK

Seasonal Shut Off Dew Point Margin

Heating

Dead Zone

Cooling

DEW POINT MARGIN In this menu the dew point margin, for controlling the dehumidifier, in the zone can be set. The dehumidifier is started when the supply temperature is equal or lower than the dew point temperature + dew point margin. The dehumidifier is shut off when the supply temperature is equal or higher than the dew point temperature + dew point margin + deadzone temperature. To set the dew point margin:

*

ES

HEATING This menu enables access to seasonal shut off settings in the zone, while in heating mode.

Default: 4.0 ˚C

MENU TREE*

Setting range: -1.0 – 10.0 ˚C

HU IT

Pump Stop

DEAD ZONE

Shut Off Outdoor Temp.

In this menu the dead zone (hysteresis) for when to shut off the dehumidifier in the zone can be set.

T. Outdoor Setpoint

LT

Valve Close

LV

T. Outdoor Delay Shut Off Indoor Temp.

To set the dead zone:

2. Press the navigation wheel to confirm selection.

HR

Heating

4. Confirm the new setting by pressing the navigation wheel again.

1. Select Dead Zone.

FR

• System Type is set to 2 Pipe, Indoor Cooling Only is set to No, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone.

3. Set the value.

2. Press the navigation wheel to confirm selection.

FI

This menu is only shown if one of the following requirements are met:

• System Type is set to 4 Pipe, Z1&2 Operation Mode is set to Only Heating or Heating And Cooling, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone.

1. Select Dew Point Margin.

EE

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

NL

T. Indoor Delay *

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

NO

3. Set the value.

Default: 2.0 ˚C

Setting range: 1.0 – 5.0 ˚C

PL

4. Confirm the new setting by pressing the navigation wheel again.

PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

121


UK PUMP STOP

T. O U T D O O R S E T P O I N T

CZ

In this menu a function to stop the circulation pump, when requirements are met, is enabled.

DE

This menu is only shown if Zone Setup is set to Stand Alone Control, and Dehumidifier is set to Disable.

In this menu the outdoor temperature setpoint for stopping the circulation pump, and/or closing the mixing valve, in the zone is set.

To enable the function: 1. Select Pump Stop.

DK

2. Press the navigation wheel to confirm selection. 3. Select Enable.

EE ES

Setting range: Disable/Enable

Default: 17.0 ˚C

Setting range: 0.0 – 40.0 ˚C, 0.1 ˚C increments

To enable the function: 1. Select Valve Close. 2. Press the navigation wheel to confirm selection. 3. Select Enable.

HU

2. Press the navigation wheel to confirm selection. 3. Select Enable.

VA LV E C LO S E

HR

1. Select T Outdoor Setpoint.

Default: Disable

In this menu a function to close the mixing valve, when requirements are met, is enabled.

FR

To set an outdoor temperature setpoint:

4. Confirm the setting by pressing the navigation wheel again.

FI

This menu is only shown if Shut Off Outdoor Temp. is enabled.

4. Confirm the setting by pressing the navigation wheel again. T. O U T D O O R D E L AY

In this menu the time delay for how long the outdoor temperature must be equal or higher than T Outdoor Setpoint before stopping the circulation pump, and/or closing the mixing valve, in the zone is set. This menu is only shown if Shut Off Outdoor Temp. is enabled.

Default: Disable

To set the delay:

Setting range: Disable/Enable

1. Select T. Outdoor Delay.

IT

4. Confirm the setting by pressing the navigation wheel again.

2. Press the navigation wheel to confirm selection.

LT

S H U T O F F O U T D O O R T E M P.

Default: 24 h

Setting range: 0 – 24 h, 1 h increments

In this menu the function to stop the circulation pump and/or when to close the mixing valve, at an outdoor temperature setpoint is enabled/disabled for the zone.

LV

This menu is only shown if Pump Stop and/or Valve Close is enabled.

NL

3. Set the value.

4. Confirm the setting by pressing the navigation wheel again.

To set an shut off outdoor temperature: 1. Select Shut Off Outdoor Temp..

NO

2. Press the navigation wheel to confirm selection. 3. Select Enable.

PL PT

Default: Disable

Setting range: Disable/Enable

4. Confirm the setting by pressing the navigation wheel again.

RO RU SE SK 122

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK S H U T O F F I N D O O R T E M P.

COOLING

In this menu the function to stop the circulation pump, and/or when to close the mixing valve, at an indoor temperature setpoint is enabled/disabled for the zone.

This menu enables access to seasonal shut off settings in the zone, while in cooling mode.

CZ

This menu is only shown if one of the following requirements are met:

DE

• System Type is set to 2 Pipe, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone..

DK

This menu is only shown if Pump Stop and/or Valve Close is enabled, and if Heating Mode is set to Outdoor + Indoor comp. for the zone. To set an shut off outdoor temperature: 1. Select Shut Off Outdoor Temp.. 2. Press the navigation wheel to confirm selection. 3. Select Enable.

Default: Disable

Setting range: Disable/Enable

• System Type is set to 4 Pipe, Z1&2 Operation Mode is set to Only Cooling or Heating And Cooling, and Zone Setup is set to Stand Alone Control or Smatrix Base PRO for the zone..

ES

MENU TREE*

Cooling

4. Confirm the setting by pressing the navigation wheel again.

FI

Pump Stop Valve Close

T . I N D O O R D E L AY

T. Outdoor Setpoint

In this menu the time delay for how long the indoor temperature must be equal or higher than the indoor setpoint before stopping the circulation pump, and/or closing the mixing valve, in the zone is set.

*

This menu is only shown if Shut Off Indoor Temp. is enabled.

In this menu a function to stop the circulation pump, when requirements are met, is enabled.

To set the delay:

To enable the function:

1. Select T. Indoor Delay.

1. Select Pump Stop.

2. Press the navigation wheel to confirm selection.

2. Press the navigation wheel to confirm selection.

3. Set the value.

3. Select Enable.

Default: 0 h

Default: Disable

Setting range: 0 – 5 h, 1 h increments

Setting range: Disable/Enable

4. Confirm the setting by pressing the navigation wheel again.

EE

FR

T. Outdoor Delay Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

HR

PUMP STOP

HU IT LT LV

4. Confirm the setting by pressing the navigation wheel again.

NL NO PL PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

123


UK VA LV E C LO S E

In this menu a function to close the mixing valve, when requirements are met, is enabled.

CZ

To enable the function:

DE

1. Select Valve Close. 2. Press the navigation wheel to confirm selection.

DK

3. Select Enable.

EE

Default: Disable

Setting range: Disable/Enable

H/C Switchover This menu enables access to settings related to switching between heating and cooling in the zone. This menu is only shown if System Type is set to 4 Pipe and Z3 Operation Mode is set to Heating And Cooling. MENU TREE* H/C Switchover H/C Switchover Outdoor Trigger Temp.

4. Confirm the setting by pressing the navigation wheel again.

ES

Outdoor Trigger Delay Indoor Trigger Temp.

T. O U T D O O R S E T P O I N T

Indoor Trigger Delay.

In this menu the outdoor temperature setpoint for stopping the circulation pump, and/or closing the mixing valve, in the zone is set.

FI

To set an outdoor temperature setpoint:

FR

1. Select T Outdoor Setpoint. 2. Press the navigation wheel to confirm selection.

HR

3. Select Enable.

HU

Default: 17.0 ˚C

Setting range: 0.0 – 40.0 ˚C, 0.1 ˚C increments

4. Confirm the setting by pressing the navigation wheel again.

IT

T . O U T D O O R D E L AY

In this menu the time delay for how long the outdoor temperature must be equal or higher than T Outdoor Setpoint before stopping the circulation pump, and/or closing the mixing valve, in the zone is set.

LT LV

Supply Setpoint for HC Switch Hysteresis *

H/C SWITCHOVER In this menu settings for switching the zone between heating and cooling is set. To select heating/cooling swithover function for the zone: 1. Select H/C Switchover. 2. Press the navigation wheel to confirm selection. 3. Select heating/cooling switchover function for the zone.

• Indoor and Outdoor uses the indoor and outdoor temperatures and time delays to switch the zone between heating and cooling.

• Supply Water Temp. uses the supply water temperature and a hysteresis to switch the zone between heating and cooling.

• Contact Input uses an external signal to switch the zone between heating and cooling.

• Force Heating sets the zone in forced heating.

• Force Cooling sets the zone in forced cooling.

To set the delay: 1. Select T. Outdoor Delay.

NL

2. Press the navigation wheel to confirm selection. 3. Set the value.

NO PL

Default: 24 h

Setting range: 0 – 24 h, 1 h increments

4. Confirm the setting by pressing the navigation wheel again.

PT

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

4. Confirm the new setting by pressing the navigation wheel again.

RO RU SE SK 124

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK OUTDOOR TRIGGER TEMP.

INDOOR TRIGGER TEMP.

In this menu one of the triggers (outdoor temperature) for switching the zone between heating and cooling is set.

In this menu one of the triggers (indoor temperature) for switching the zone between heating and cooling is set.

N OT E ! All triggers and time delays must be met for the zone to switch heating/cooling mode.

N OT E ! All triggers and time delays must be met for the zone to switch heating/cooling mode.

This menu is only shown if H/C Switchover is set to Indoor and Outdoor.

This menu is only shown if H/C Switchover is set to Indoor and Outdoor.

To set the outdoor trigger temperature:

To set the indoor trigger temperature:

1. Select Outdoor Trigger Temp.

1. Select Indoor Trigger Temp.

2. Press the navigation wheel to confirm selection.

2. Press the navigation wheel to confirm selection.

3. Set the value.

3. Set the value.

Default: 20.0 ˚C

Default: 22.0 ˚C

Setting range: 5.0 – 30.0 ˚C, 0.1 ˚C increments

Setting range: 5.0 – 30.0 ˚C, 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again.

4. Confirm the new setting by pressing the navigation wheel again.

OUTDOOR TRIGGER DELAY

INDOOR TRIGGER DELAY

In this menu one of the triggers (delay for outdoor temperature) for switching the zone between heating and cooling is set.

In this menu one of the triggers (delay for indoor temperature) for switching the zone between heating and cooling is set.

N OT E ! All triggers and time delays must be met for the zone to switch heating/cooling mode.

N OT E ! All triggers and time delays must be met for the zone to switch heating/cooling mode.

This menu is only shown if H/C Switchover is set to Indoor and Outdoor.

This menu is only shown if H/C Switchover is set to Indoor and Outdoor.

To set the outdoor trigger delay:

To set the indoor trigger delay:

1. Select Outdoor Trigger Delay.

1. Select Indoor Trigger Delay.

2. Press the navigation wheel to confirm selection.

2. Press the navigation wheel to confirm selection.

3. Set the value.

3. Set the value.

Default: 24 h

Default: 24 h

Setting range: 1 – 48 h, 1 h increments

Setting range: 1 – 48 h, 1 h increments

4. Confirm the new setting by pressing the navigation wheel again.

CZ DE DK EE ES FI FR HR HU IT LT LV NL NO

4. Confirm the new setting by pressing the navigation wheel again.

PL PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

125


UK CZ

SUPPLY SETPOINT FOR HC SWITCH

HYSTERESIS

In this menu the supply temperature setpoint for switching between heating and cooling is set.

In this menu the hysteresis which is used to switch between heating and cooling using Supply Setpoint for HC Switch is set.

The zone switches to heating when the supply temperature is higher than Supply Setpoint for HC Switch. The zone switches back when the supply temperature is lower than Supply Setpoint for HC Switch - Hysteresis.

DE DK

The zone switches to cooling when the supply temperature is lower than Supply Setpoint for HC Switch. The zone switches back when the supply temperature is lower than Supply Setpoint for HC Switch + Hysteresis.

EE ES

N OT E ! When using this switch mode, the heating/ cooling switch is done in the heat pump/ chiller. The Move PRO controller switches the operation mode when it detects the change in supply temperture.

FI FR

No diverting valves are controlled in this mode.

HR

This menu is only shown if H/C Switchover is set to Supply Water Temp..

HU

To set the hysteresis: 1. Select Hysteresis. 2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 2 ˚C

Setting range: 0 – 4 ˚C, 1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again. Automatic Freeze Protection This menu decides when to activate automatic freeze protection during meltaway in the zone. The controller will kepp the return temperature between the low and high thersholds. This menu is only shown if Zone Setup is set to Meltaway for the zone. MENU TREE Automatic Freeze Protection

To set the supply temperature setpoint for HC switch:

Primary return Temp. Low

1. Select Supply Setpoint for HC Switch.

IT

Primary return Temp. High

2. Press the navigation wheel to confirm selection.

LT LV

3. Set the value.

PRIMARY RETURN TEMP. LOW

Default: 18 ˚C

In this menu the lower threshold is set.

Setting range: 5 – 30 ˚C, 1 ˚C increments

To set the low threshold:

4. Confirm the new setting by pressing the navigation wheel again.

NL

1. Select Primary return Temp. Low. 2. Press the navigation wheel to confirm selection. 3. Set a value.

NO

Default: 0.0 ˚C

Setting range: -5.0 – 5.0 ˚C, 0.1 ˚C increments

4. Confirm the setting by pressing the navigation wheel again.

PL PT RO RU SE SK 126

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK PRIMARY RETURN TEMP. HIGH

H/C S witchover

In this menu the higher threshold is set.

This menu enables access to settings related to switching between heating and cooling in the zone.

CZ DE

2. Press the navigation wheel to confirm selection.

This menu is only shown if System Type is set to 2 Pipe and one of the zones is not set to Smatrix Base PRO.

3. Set a value.

Menu tree*

DK

To set the high threshold: 1. Select Primary return Temp. High.

Default: 15.0 ˚C

Setting range: 15.0 – 45.0 ˚C, 0.1 ˚C increments

H/C Switchover H/C Switchover

4. Confirm the setting by pressing the navigation wheel again.

Outdoor Trigger Temp.

Condensation Delay

Indoor Trigger Temp.

In this menu the condensation delay in the zone is set. If condensation is not detected (by the condensation sensor in the zone) during the time set in the delay, the condensation status (in the zone information menu) switches to No.

Outdoor Trigger Delay

Supply Setpoint for HC Switch

FI

Hysteresis *

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

H/C Switchover

To set the condensation delay:

In this menu settings for switching the zone between heating and cooling is set.

2. Press the navigation wheel to confirm selection.

To select heating/cooling swithover function for the zone:

3. Set the value.

1. Select H/C Switchover.

Default: 10 min

2. Press the navigation wheel to confirm selection.

Setting range: 0 – 120 min, 1 min increments

3. Select heating/cooling switchover function for the zone.

4. Confirm the new setting by pressing the navigation wheel again.

ES

Indoor Trigger Delay.

This menu is only shown if Condensation Sensor is enabled in the startup wizard for the zone.

1. Select Condensation Delay.

EE

FR HR HU IT LT

• Indoor and Outdoor uses the indoor and outdoor temperatures and time delays to switch the zone between heating and cooling.

LV

• Supply Water Temp. uses the supply water temperature and a hysteresis to switch the zone between heating and cooling.

NL

• Contact Input uses an external signal to switch the zone between heating and cooling.

NO

• Force Heating sets the zone in forced heating.

• Force Cooling sets the zone in forced cooling.

PL

4. Confirm the new setting by pressing the navigation wheel again.

PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

127


UK CZ

Outdoor Trigger Temp.

Indoor Trigger Temp.

In this menu one of the triggers (outdoor temperature) for switching the zone between heating and cooling is set.

In this menu one of the triggers (indoor temperature) for switching the zone between heating and cooling is set.

DE

N OT E ! All triggers and time delays must be met for the zone to switch heating/cooling mode.

N OT E ! All triggers and time delays must be met for the zone to switch heating/cooling mode.

This menu is only shown if H/C Switchover is set to Indoor and Outdoor.

This menu is only shown if H/C Switchover is set to Indoor and Outdoor.

To set the outdoor trigger temperature:

To set the indoor trigger temperature:

1. Select Outdoor Trigger Temp.

1. Select Indoor Trigger Temp.

2. Press the navigation wheel to confirm selection.

2. Press the navigation wheel to confirm selection.

3. Set the value.

3. Set the value.

Default: 20.0 ˚C

Default: 22.0 ˚C

Setting range: 5.0 – 30.0 ˚C, 0.1 ˚C increments

Setting range: 5.0 – 30.0 ˚C, 0.1 ˚C increments

DK EE ES FI FR

4. Confirm the new setting by pressing the navigation wheel again.

4. Confirm the new setting by pressing the navigation wheel again.

HR

Outdoor Trigger Delay

Indoor Trigger Delay

HU

In this menu one of the triggers (delay for outdoor temperature) for switching the zone between heating and cooling is set.

In this menu one of the triggers (delay for indoor temperature) for switching the zone between heating and cooling is set.

IT

N OT E ! All triggers and time delays must be met for the zone to switch heating/cooling mode.

N OT E ! All triggers and time delays must be met for the zone to switch heating/cooling mode.

LT

This menu is only shown if H/C Switchover is set to Indoor and Outdoor.

This menu is only shown if H/C Switchover is set to Indoor and Outdoor.

To set the outdoor trigger delay:

To set the indoor trigger delay:

1. Select Outdoor Trigger Delay.

1. Select Indoor Trigger Delay.

2. Press the navigation wheel to confirm selection.

2. Press the navigation wheel to confirm selection.

3. Set the value.

3. Set the value.

Default: 24 h

Default: 24 h

Setting range: 1 – 48 h, 1 h increments

Setting range: 1 – 48 h, 1 h increments

LV NL NO

4. Confirm the new setting by pressing the navigation wheel again.

PL

4. Confirm the new setting by pressing the navigation wheel again.

PT RO RU SE SK 128

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Supply Setpoint for HC Switch

Hysteresis

In this menu the supply temperature setpoint for switching between heating and cooling is set.

In this menu the hysteresis which is used to switch between heating and cooling using Supply Setpoint for HC Switch is set.

CZ

To set the hysteresis:

DE

The zone switches to heating when the supply temperature is higher than Supply Setpoint for HC Switch. The zone switches back when the supply temperature is lower than Supply Setpoint for HC Switch - Hysteresis. The zone switches to cooling when the supply temperature is lower than Supply Setpoint for HC Switch. The zone switches back when the supply temperature is lower than Supply Setpoint for HC Switch + Hysteresis.

1. Select Hysteresis.

DK

2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 2 ˚C

Setting range: 0 – 4 ˚C, 1 ˚C increments

EE

4. Confirm the new setting by pressing the navigation wheel again.

ES

N OT E ! When using this switch mode, the heating/ cooling switch is done in the heat pump/ chiller. The Move PRO controller switches the operation mode when it detects the change in supply temperture.

FI FR

No diverting valves are controlled in this mode.

HR

This menu is only shown if H/C Switchover is set to Supply Water Temp..

HU

To set the supply temperature setpoint for HC switch: 1. Select Supply Setpoint for HC Switch.

IT

2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 18 ˚C

Setting range: 5 – 30 ˚C, 1 ˚C increments

LT LV

4. Confirm the new setting by pressing the navigation wheel again.

NL NO PL PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

129


UK CZ

C ontroller S ettings

Language

In this menu parameter settings for the controller can be set or changed.

In this menu the language of the system is set. To set the language:

Menu tree

DE

1. Select Language.

Controller Settings

2. Press the navigation wheel to confirm selection. Time

DK

Date Language

EE

3. Select a language. 4. Confirm the setting by pressing the navigation wheel again.

Time In this menu the time of the system is set.

ES

To set the time: 1. Select Time.

FI

2. Press the navigation wheel to confirm selection. 3. Set the hours.

FR

4. Press the navigation wheel to confirm selection. 5. Set the minutes.

HR

6. Confirm the setting by pressing the navigation wheel again.

HU

Date In this menu the date of the system is set.

IT

To set the date: 1. Select Date.

LT

2. Press the navigation wheel to confirm selection. 3. Set the day. 4. Press the navigation wheel to confirm selection.

LV

5. Set the month. 6. Press the navigation wheel to confirm selection.

NL

7. Set the year. 8. Confirm the setting by pressing the navigation wheel again.

NO PL PT RO RU SE SK 130

U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK

7.11 Pre Heating Info This menu shows information about the system, enabled zones and the controller (when the operating mode is set to Pre Heating in the startup wizard).

Z one 1 I nformation This menu shows information about zone 1.

CZ

Menu tree

DE

Zone 1 Information

Menu tree*

Supply temperature State

Pre Heating Info Zone 1 Information Zone 2 Information Zone 3 Information Controller Information *

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

S ystem

information

The system information menu shows the current time and date.

DK

Time Left

System information

Supply temperature

EE

The current supply temperature is shown. The temperature is measured by the supply temperature sensor wired to the controller.

ES

State The current pre-heating state (phase) in the zone is shown.

FI

Pre heating is run in three different phases.

FR

Pase 1: The supply temperature setpoint is set to 25 ˚C for 3 days (can be set in the Settings menu).

Pase 2: The supply temperature setpoint is set to maximum allowed calculated setpoint for 4 days (can be set in the Settings menu).

HR HU

Pase 3: The controller enters Standby mode until the startup wizard is restarted (Settings > Installer Settings > Restart wizard). Frost protection is active during this final phase.

IT LT

Time Left The time left of the current pre-heating phase in the zone is shown.

LV NL NO PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

131


UK CZ

Z one 2 I nformation

Z one 3 I nformation

This menu shows information about zone 2.

This menu shows information about zone 3.

Menu tree

Menu tree

DE

Zone 2 Information

DK EE ES FI FR HR

LT LV

Supply temperature

Supply temperature

State

State

Time Left

Time Left

Supply temperature

Supply temperature

The current supply temperature is shown. The temperature is measured by the supply temperature sensor wired to the controller.

The current supply temperature is shown. The temperature is measured by the supply temperature sensor wired to the controller.

State

State

The current pre-heating state (phase) in the zone is shown.

The current pre-heating state (phase) in the zone is shown.

Pre heating is run in three different phases.

Pre heating is run in three different phases.

Pase 1: The supply temperature setpoint is set to 25 ˚C for 3 days (can be set in the Settings menu).

Pase 1: The supply temperature setpoint is set to 25 ˚C for 3 days (can be set in the Settings menu).

Pase 2: The supply temperature setpoint is set to maximum allowed calculated setpoint for 4 days (can be set in the Settings menu).

Pase 2: The supply temperature setpoint is set to maximum allowed calculated setpoint for 4 days (can be set in the Settings menu).

Pase 3: The controller enters Standby mode until the startup wizard is restarted (Settings > Installer Settings > Restart wizard). Frost protection is active during this final phase.

Pase 3: The controller enters Standby mode until the startup wizard is restarted (Settings > Installer Settings > Restart wizard). Frost protection is active during this final phase.

HU IT

Zone 3 Information

Time Left

Time Left

The time left of the current pre-heating phase in the zone is shown.

The time left of the current pre-heating phase in the zone is shown.

NL NO PL PT RO RU SE SK 132

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK C ontroller I nformation This menu shows information about the controller. Menu tree Controller Information Language About...

Language This menu show the set display language for the controller.

7.12 Pre Heating Settings In this menu installer settings, enabled zone settings, and controller settings can be changed (when the operating mode is set to Pre Heating in the startup wizard).

CZ DE

See section 5.14 Pre heating concrete slab (DIN 1264-4) for more information.

DK

Menu tree*

EE

Pre Heating Settings Installer Settings Zone 1 Settings

About...

ES

Zone 2 Settings

This menu shows the serial number, software versions, and hardware versions of the controller.

Zone 3 Settings Controller Settings *

FI

Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

I nstaller S ettings

FR

In this menu lock codes (to gain access to locked parameter settings) can be set or changed, factory settings can be restored, backup of controller parameter settings can be managed, or the setup wizard can be restarted.

HR HU

Menu tree Installer Settings

IT Lock code Change lock code

LT

Display settings Restore factory settings Restore backup

LV

New backup Restart wizard

NL NO PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

133


UK Change lock code

A lock code can be used to block a user from changing parameter settings. The menu system is fully accessible, but the lock code is required to enter and change parameter settings.

The standard lock code which is used to block a user from changing parameter settings, can be changed in this menu.

CZ

Lock code

DE

This menu is only shown when Lock code has been enabled in the Lock code menu.

The default lock code is 0000. It is recommended to change this code if using this function.

DK

N OT E ! If the controller display is already locked, it has to be unlocked before entering the new lock code.

The controller will stay unlocked until it has been left untouched fro about 10 minutes. Then it will lock itself again.

EE

To change the lock code:

1. Select Lock code.

1. Select Change lock code.

2. Press the navigation wheel to confirm selection.

2. Press the navigation wheel to confirm selection.

3. Select Enable. 4. Press the navigation wheel to confirm selection.

3. Enter the new lock code in the boxes using the navigation wheel.

ENTERING A MENU WHEN LOCK CODE IS ENABLED

Turn the navigation wheel to either select a box, or to increase/decrease a value in edit mode.

Press the navigation wheel to enter edit mode or to confirm the new setting.

2. Press the navigation wheel to confirm selection.

Default: 0000

3. Enter the lock code in the boxes using the navigation wheel.

4. Confirm the new lock code by pressing and holding the navigation wheel for about 8 seconds.

ES

To enable lock code in the controller:

FI FR

To enter a lock code: 1. Select the parameter.

HR HU

Turn the navigation wheel to either select a box, or to increase/decrease a value in edit mode.

Display settings

Press the navigation wheel to enter edit mode or to confirm the new setting.

Default: 0000

This menu enables display settings, such as contrast, and it also shows the version number of the display software.

IT LT

4. Confirm the lock code by pressing and holding the navigation wheel for a number of seconds.

LV

5. Change the parameter setting and exit.

To set the display contrast: 1. Select Display settings. 2. Press the navigation wheel to confirm selection. 3. Select Display contrast.

NL

4. Press the navigation wheel to confirm selection. 5. Set the display contrast.

NO

Setting range: -50 – 100 %, 1 % increments

6. Press the navigation wheel to confirm selection.

PL PT RO RU SE SK 134

U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Restore factory settings

New backup

This menu enables all parameter settings in the controller to be reset to the factory default settings.

This menu enables the controller to save a backup of all parameter settings to the microSD-card.

To restore the factory settings:

To save from a backup:

1. Select Restore factory settings.

1. Make sure a microSD-card, where the backup is to be saved, into the controller.

2. Press the navigation wheel to confirm selection. 3. Select Yes.

Setting range: No (default)/Yes

4. Press the navigation wheel to confirm selection. 5. All parameters in the controller are being restored to factory settings. Restore backup This menu enables the controller to restore all parameter settings from a previously created backup located on the microSD-card. To restore from a backup: 1. Make sure the microSD-card with the backup is inserted into the controller. 2. Select Restore backup. 3. Press the navigation wheel to confirm selection. 4. Select Yes.

Setting range: No (default)/Yes

5. Press the navigation wheel to confirm selection.

CZ DE DK

2. Select New backup. 3. Press the navigation wheel to confirm selection.

EE

4. Select Yes.

Setting range: No (default)/Yes

5. Press the navigation wheel to confirm selection.

ES

6. All parameters in the controller are being saved to the microSD card.

FI

Restart wizard This menu enables the controller to restart the setup wizard.

FR

To restart the setup wizard:

HR

1. Select Restart wizard. 2. Press the navigation wheel to confirm selection.

HU

3. Select Yes.

Setting range: No (default)/Yes

IT

4. Press the navigation wheel to confirm selection. 5. The setup wizard is now being restarted.

6. All parameters in the controller are being restored from backup.

LT LV NL NO PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

135


UK Z one 1 S ettings

P-area

In this menu parameter settings for zone 1 can be set or changed.

CZ

To set the P-area:

Menu tree

DE

1. Select P-area.

Zone 1 Settings Z1 Max. Calc. Supply Setpoint

DK

Frost Protection Setpoint P-area

EE

I-time Actuator running time

ES

In this menu the P-area for the mixing valve regulation is set.

2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 140.0 ˚C

Setting range: 2.0 – 500.0 ˚C, 0.1 ˚C increments

4. Confirm the setting by pressing the navigation wheel again.

Z1 Max. Calc. Supply Setpoint In this menu the maximum allowed calculated supply setpoint for the zone can be set.

FI

To set the maximum allowed calculated supply setpoint:

FR

1. Select Z1 Max. Calc. Supply Setpoint. 2. Press the navigation wheel to confirm selection.

HR

3. Set the value.

HU

Default: 45.0 ˚C

Setting range: -5.0 – 70.0 ˚C, 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again.

IT

I-time In this menu the I-time for the mixing valve regulation is set. To set the I-time: 1. Select I-time. 2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 35 seconds

Setting range: 5 – 300 seconds, 1 second increments

4. Confirm the setting by pressing the navigation wheel again.

Frost Protection Setpoint In this menu the frost protection setpoint (minimum available supply temperature) for the zone can be set. The supply temperature is not allowed to fall below this value.

LT LV NL NO PL

Actuator running time In this menu the actuator running time for the mixing valve regulation is set. To set the actuator running time:

To set the frost protection setpoint:

1. Select Actuator running time.

1. Select Frost Protection Setpoint.

2. Press the navigation wheel to confirm selection.

2. Press the navigation wheel to confirm selection.

3. Set the value.

3. Set the value.

Default: 120 seconds

Default: 5.0 ˚C

Setting range: 0 – 500 seconds, 1 second increments

Setting range: 5.0 – 20.0 ˚C (or max. supply temp), 0.1 ˚C increments

4. Confirm the setting by pressing the navigation wheel again.

4. Confirm the new setting by pressing the navigation wheel again.

PT RO RU SE SK 136

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Z one 2 S ettings

P-area

In this menu parameter settings for zone 2 can be set or changed.

In this menu the P-area for the mixing valve regulation is set.

CZ

To set the P-area:

Menu tree

DE

1. Select P-area.

Zone 2 Settings Z2 Max. Calc. Supply Setpoint Frost Protection Setpoint P-area I-time Actuator running time

2. Press the navigation wheel to confirm selection.

DK

3. Set the value.

Default: 200.0 ˚C

Setting range: 2.0 – 500.0 ˚C, 0.1 ˚C increments

EE

4. Confirm the setting by pressing the navigation wheel again.

ES

Z2 Max. Calc. Supply Setpoint In this menu the maximum allowed calculated supply setpoint for the zone can be set. To set the maximum allowed calculated supply setpoint: 1. Select Z2 Max. Calc. Supply Setpoint. 2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 45.0 ˚C

Setting range: -5.0 – 70.0 ˚C, 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again.

I-time

FI

In this menu the I-time for the mixing valve regulation is set. To set the I-time:

FR

1. Select I-time. 2. Press the navigation wheel to confirm selection.

HR

3. Set the value.

Default: 50 seconds

Setting range: 5 – 300 seconds, 1 second increments

HU

4. Confirm the setting by pressing the navigation wheel again.

IT

Frost Protection Setpoint In this menu the frost protection setpoint (minimum available supply temperature) for the zone can be set. The supply temperature is not allowed to fall below this value.

Actuator running time In this menu the actuator running time for the mixing valve regulation is set.

LT

To set the actuator running time:

LV

To set the frost protection setpoint:

1. Select Actuator running time.

1. Select Frost Protection Setpoint.

2. Press the navigation wheel to confirm selection.

2. Press the navigation wheel to confirm selection.

3. Set the value.

3. Set the value.

Default: 60 seconds

Default: 5.0 ˚C

Setting range: 0 – 500 seconds, 1 second increments

Setting range: 5.0 – 20.0 ˚C (or max. supply temp), 0.1 ˚C increments

4. Confirm the setting by pressing the navigation wheel again.

NL NO PL

4. Confirm the new setting by pressing the navigation wheel again.

PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

137


UK Z one 3 S ettings

P-area

In this menu parameter settings for zone 3 can be set or changed.

CZ

To set the P-area:

Menu tree

DE

1. Select P-area.

Zone 3 Settings Z3 Max. Calc. Supply Setpoint

DK

Frost Protection Setpoint P-area

EE

I-time Actuator running time

ES

In this menu the P-area for the mixing valve regulation is set.

2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 200.0 ˚C

Setting range: 2.0 – 500.0 ˚C, 0.1 ˚C increments

4. Confirm the setting by pressing the navigation wheel again.

Z3 Max. Calc. Supply Setpoint In this menu the maximum allowed calculated supply setpoint for the zone can be set.

FI

To set the maximum allowed calculated supply setpoint:

FR

1. Select Z1 Max. Calc. Supply Setpoint. 2. Press the navigation wheel to confirm selection.

HR

3. Set the value.

HU

Default: 45.0 ˚C

Setting range: -5.0 – 70.0 ˚C, 0.1 ˚C increments

4. Confirm the new setting by pressing the navigation wheel again.

IT

I-time In this menu the I-time for the mixing valve regulation is set. To set the I-time: 1. Select I-time. 2. Press the navigation wheel to confirm selection. 3. Set the value.

Default: 50 seconds

Setting range: 5 – 300 seconds, 1 second increments

4. Confirm the setting by pressing the navigation wheel again.

Frost Protection Setpoint In this menu the frost protection setpoint (minimum available supply temperature) for the zone can be set. The supply temperature is not allowed to fall below this value.

LT LV NL NO PL

Actuator running time In this menu the actuator running time for the mixing valve regulation is set. To set the actuator running time:

To set the frost protection setpoint:

1. Select Actuator running time.

1. Select Frost Protection Setpoint.

2. Press the navigation wheel to confirm selection.

2. Press the navigation wheel to confirm selection.

3. Set the value.

3. Set the value.

Default: 60 seconds

Default: 5.0 ˚C

Setting range: 0 – 500 seconds, 1 second increments

Setting range: 5.0 – 20.0 ˚C (or max. supply temp), 0.1 ˚C increments

4. Confirm the setting by pressing the navigation wheel again.

4. Confirm the new setting by pressing the navigation wheel again.

PT RO RU SE SK 138

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK C ontroller S ettings

Language

In this menu parameter settings for the controller can be set or changed.

In this menu the language of the system is set.

CZ

To set the language: Menu tree

1. Select Language.

Controller Settings

DE

2. Press the navigation wheel to confirm selection. Time Date Language Operation mode

Time In this menu the time of the system is set.

3. Select a language.

EE Operation mode In this menu the operation mode of the system is set.

To set the time:

This setting is used to change from pre heating to standard mode, when done pre heating.

1. Select Time.

To set operation mode:

2. Press the navigation wheel to confirm selection. 3. Set the hours. 4. Press the navigation wheel to confirm selection. 5. Set the minutes.

In this menu the date of the system is set. To set the date:

ES FI

1. Select Operation mode.

FR

2. Press the navigation wheel to confirm selection. 3. Select an operation mode.

Standard: This selection will make the controller to restart the startup wizard, after a small delay.

Pre Heating: This selection will make the controller stay in Pre Heating mode.

6. Confirm the setting by pressing the navigation wheel again. Date

DK

4. Confirm the setting by pressing the navigation wheel again.

HR HU IT

4. Confirm the setting by pressing the navigation wheel again.

1. Select Date.

LT

2. Press the navigation wheel to confirm selection. 3. Set the day.

LV

4. Press the navigation wheel to confirm selection. 5. Set the month.

NL

6. Press the navigation wheel to confirm selection. 7. Set the year.

NO

8. Confirm the setting by pressing the navigation wheel again.

PL PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

139


UK

7.13 Menu tree CZ

N OT E ! Parts of the menu tree may only be visible in the Move PRO controller depending on its current configuration.

DE

S tandard O perating M ode DK

System Overview Information

System information

EE

Time Date Outdoor Temperature

ES

Zone 1 Information

Zone Setup Heating Mode

FI

Operating Mode Supply temperature Mixing Valve

FR

Pump Heating

HR

Heating Curve Calculated Supply Setpoint Indoor temperature

HU

ECO-Comf Status Cooling

IT

Cooling Curve Calculated Supply Setpoint Condensation

LT

Relative Humidity Dew Point Temperature Dehumidifier

LV Zone 2 Information

Zone Setup Heating Mode

NL

Operating Mode Supply temperature

NO

Calculated Supply Setpoint DHW Circ. Return Temperature

PL

Mixing Valve Pump

PT

Heating

Heating Curve Calculated Supply Setpoint

RO

Indoor temperature ECO-Comf Status

RU SE SK 140

U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Cooling

Cooling Curve Calculated Supply Setpoint

CZ

Condensation Relative Humidity

DE

Dew Point Temperature Dehumidifier Zone 3 Information

DK

Zone Setup Heating Mode

EE

Operating Mode Supply temperature Calculated Supply Setpoint

ES

Indoor temperature Meltaway Curve

FI

Return temperature Ground Temperature

FR

Ground Moisture Primary Return Temperature Status

HR

Mixing Valve Pump

HU

Status Heating

Heating Curve

IT

Calculated Supply Setpoint Indoor temperature ECO-Comf Status Cooling

LT

Cooling Curve

LV

Calculated Supply Setpoint Condensation Relative Humidity

NL

Dew Point Temperature Dehumidifier

NO Controller Information

Language About...

PL Alarms

Active alarms Alarm history

PT

Acknowledge all alarms Reset alarm history

RO RU SE SK U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

141


UK Settings

Installer Settings

T Outdoor Fallback Lock code

CZ

Change lock code Display settings

DE

Restore factory settings Restore backup

DK

New backup Restart wizard

EE

Zone 1 Settings

Supply Temp. Settings

Heating

Calculated Supply Setpoint Heating Min. Supply Temp. Heating Max. Supply Temp.

ES

Deviation alarm limit Deviation alarm delay

FI

Cooling

Calculated Supply Setpoint Cooling Min. Supply Temp.

FR

Cooling Max. Supply Temp. Dew Point Margin Dew Point Offset

HR Heating Indoor Temp. Settings

HU

Indoor Setpoint Calculated Indoor Setpoint ECO-Comf. Status Indoor Setpoint Influence (Lower)

IT

Indoor Setpoint Influence (Upper)

LT Comf. - ECO

ECO Setback ECO-Comf Status

LV

ECO-Comf Schedule Heating Curve

NL

Setting Offset Heating Curve

NO Cooling Curve

Setting Offset

PL

Cooling Curve Manual Operation

PT

Manual Mode Pump Mixing valve

RO Pump

Pump Exercise Exercise Day of the Week

RU

Exercise Hour Exercise Min

SE SK 142

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Mixing Valve

Heating

P-area I-time

CZ

Actuator running time Cooling

P-area

DE

I-time Actuator running time

DK Dehumidifier Control

Dew Point Margin Dead Zone

EE Seasonal Shut Off

Heating

Pump Stop Valve Close

ES

Shut Off Outdoor Temp. T. Outdoor Setpoint T. Outdoor Delay

FI

Shut Off Indoor Temp. T. Indoor Delay

FR Cooling

Pump Stop Valve Close

HR

T. Outdoor Setpoint T. Outdoor Delay HC Switchover

HU

H/C Switchover Outdoor Trigger Temp. Outdoor Trigger Delay

IT

Indoor Trigger Temp. Indoor Trigger Delay.

LT

Supply Setpoint for HC Switch Hysteresis

LV

Condensation Delay Zone 2 Settings

Supply Temp. Settings

Heating

Calculated Supply Setpoint

NL

Heating Min. Supply Temp. Heating Max. Supply Temp.

NO

Deviation alarm limit Deviation alarm delay Cooling

PL

Calculated Supply Setpoint Cooling Min. Supply Temp.

PT

Cooling Max. Supply Temp. Dew Point Margin Dew Point Offset

RO

DHW Supply Setpoint Overheating alarm limit

RU

Overheating alarm delay Deviation alarm limit

SE

Deviation alarm delay

SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

143


UK Heating Indoor Temp. Settings

CZ

Indoor Setpoint Calculated Indoor Setpoint ECO-Comf. Status

DE

Indoor Setpoint Influence (Lower) Indoor Setpoint Influence (Upper)

DK DHW Circ Return Settings

EE

DHW Circ Return Setpoint BoostPower

Comf. - ECO

ES

ECO Setback ECO-Comf Status ECO-Comf Schedule

FI

Heating Curve

Setting Offset Heating Curve

FR Cooling Curve

Setting Offset

HR

Cooling Curve

HU

Manual Operation

Manual Mode Pump Mixing valve

IT Pump

Pump Exercise Exercise Day of the Week

LT

Exercise Hour Exercise Min

LV Mixing Valve

Heating

P-area I-time

NL

Actuator running time Cooling

NO

P-area I-time Actuator running time

PL

P-area I-time

PT

Actuator running time Dehumidifier Control

RO

Dew Point Margin Dead Zone

RU SE SK 144

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Seasonal Shut Off

Heating

Pump Stop Valve Close

CZ

Shut Off Outdoor Temp. T. Outdoor Setpoint

DE

T. Outdoor Delay Shut Off Indoor Temp.

DK

T. Indoor Delay Cooling

Pump Stop

EE

Valve Close T. Outdoor Setpoint T. Outdoor Delay HC Switchover

ES

H/C Switchover Outdoor Trigger Temp.

FI

Outdoor Trigger Delay Indoor Trigger Temp.

FR

Indoor Trigger Delay. Supply Setpoint for HC Switch

HR

Hysteresis Condensation Delay Zone 3 Settings

Supply Temp. Settings

HU Heating

Calculated Supply Setpoint Heating Min. Supply Temp.

IT

Heating Max. Supply Temp. Deviation alarm limit

LT

Deviation alarm delay Cooling

Calculated Supply Setpoint

LV

Cooling Min. Supply Temp. Cooling Max. Supply Temp. Dew Point Margin

NL

Dew Point Offset Calculated Supply Setpoint

NO

Melting Supply Setpoint Heating Curve Meltaway

PL

IDLE Supply Setpoint Min. Supply Temp. (IDLE Status)

PT

Max. Supply Temp. (IDLE Status) Heating Indoor Temp. Settings

RO

Indoor Setpoint Calculated Indoor Setpoint

RU

ECO-Comf. Status Indoor Setpoint Influence (Lower)

SE

Indoor Setpoint Influence (Upper)

SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

145


UK Comf. - ECO

ECO Setback ECO-Comf Status

CZ

ECO-Comf Schedule

DE

Heating Curve

Setting Offset Heating Curve

DK Cooling Curve

Setting Offset

EE

Cooling Curve Meltaway Curve (IDLE Status)

ES

Setting Offset

FI

Heating Curve

FR

Return Temperature

Max. Supply-Return Diff.

Enter Stop State Conditions

Outdoor Temperature Delay (days)

HR

Enter Idle State Conditions

Outdoor Temperature Delay (hours)

HU

Delay Surface Dry Enter Melting State Conditions

IT

Ground Temperature Limit Outdoor Temp. Offset Outdoor Temperature Low Limit

LT

Min. Time in Melting

LV

Manual Operation

Manual Mode Pump Mixing valve

NL Pump

Pump Exercise

NO

Exercise Day of the Week Exercise Hour Exercise Min

PL Mixing Valve

Heating

P-area I-time

PT

Actuator running time Cooling

RO

P-area I-time Actuator running time

RU P-area I-time

SE

Actuator running time

SK 146

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Dehumidifier Control

Dew Point Margin Dead Zone

Seasonal Shut Off

Heating

CZ Pump Stop

DE

Valve Close Shut Off Outdoor Temp. T. Outdoor Setpoint

DK

T. Outdoor Delay Shut Off Indoor Temp.

EE

T. Indoor Delay Cooling

Pump Stop

ES

Valve Close T. Outdoor Setpoint T. Outdoor Delay HC Switchover

FI

H/C Switchover Outdoor Trigger Temp.

FR

Outdoor Trigger Delay Indoor Trigger Temp.

HR

Indoor Trigger Delay. Supply Setpoint for HC Switch

HU

Hysteresis Automatic Freeze Protection

Primary return Temp. Low

IT

Primary return Temp. High Condensation Delay HC Switchover

LT

H/C Switchover Outdoor Trigger Temp.

LV

Outdoor Trigger Delay Indoor Trigger Temp.

NL

Indoor Trigger Delay. Supply Setpoint for HC Switch

NO

Hysteresis Controller Settings

Time

PL

Date Language

PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

147


UK P re H eating O perating M ode System Overview

CZ

Pre Heating Info

System information

DE

Time Date

Zone 1 Information

DK

Z1 - Supply Temperature State Time Left

EE

Zone 2 Information

Z2 - Supply Temperature State

ES

Time Left Zone 3 Information

FI

Z3 - Supply Temperature State Time Left

FR

Controller Information

Language About...

HR

Alarms

Active alarms Alarm history Acknowledge all alarms

HU

Reset alarm history

IT LT LV NL NO PL PT RO RU SE SK 148

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK Pre Heating Settings

Installer Settings

Lock code Change lock code

CZ

Display settings Restore factory settings

DE

Restore backup New backup

Zone 1 Settings

Restart wizard

DK

Z1 Max. Calc. Supply Setpoint

EE

Frost Protection Setpoint P-area

ES

I-time Actuator running time Zone 2 Settings

FI

Z2 Max. Calc. Supply Setpoint Frost Protection Setpoint

FR

P-area I-time

Zone 3 Settings

Actuator running time

HR

Z3 Max. Calc. Supply Setpoint

HU

Frost Protection Setpoint P-area

IT

I-time Actuator running time

LT Controller Settings

Time Date

LV

Language Operation mode

NL NO PL PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

149


UK

8 Maintenance

CZ DE

The maintenance of Uponor Smatrix Move PRO includes the following:

DK

• Manual preventive maintenance • Automatic preventive maintenance

EE

• Corrective maintenance • Controller display

ES

8.1 Manual preventive maintenance Uponor Smatrix Move PRO requires no preventive maintenance except cleaning:

FI

1. Use a dry soft cloth to clean the components.

FR W arning ! Do not use any detergents to clean the Uponor Smatrix Move PRO components.

HR

8.2 Automatic preventive maintenance HU IT

Uponor Smatrix Move PRO is equipped with an automatic exercise function. This function consists of a test run designed to prevent the pump from seizing up due to inactivity.

LT

This exercise is run a fixed intervals, set in the menu system:

8.3 Corrective maintenance F allback

mode

If a sensor is malfunctioning or not detected, the controller triggers an alarm and executes the fallback mode to maintain the temperature in the zone until the problem is resolved.

R esetting

the controller

If the controller does not work as expected, for example due to a hang-up, it can be reset (requires a service level code) to solve the problem: See section 7.10 Settings > Installer Settings > Restore factory settings for more information.

8.4 Controller display It is recommended to occasionally check the display on the controller for alarms. The display flashes continuously for general alarms, until acknowledged. Determine what is causing the alarm by reading the alarm description. See section 7.8 Alarms for more information.

See section 7.10 Settings > Zone # Settings > Pump > Pump Exercise for more information.

LV

• The pump exercise operates only in the zone if enabled in the Move PRO controller display. The pump is activated for 1 minutes during the exercise.

NL NO PL PT RO RU SE SK 150

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK

9 Troubleshooting

CZ DE

The table below shows problems and alarms that can occur with Uponor Smatrix Move PRO and describes solutions. A common cause of a problem though may be due to wrongly installed loops or mixed up thermostats. Problem Fluctuating floor temperature

Indication Floor temperature is changing abnormally between hot and cold Room temperature does not match setpoint on the controller, and mixing valves open/close on a fixed interval Room temperature does not match setpoint on the controller

Probable cause Supply water temperature is too high

Solutions Check boiler or mixing valve

Heating fall back function is activated due to lost communication with an room sensor The room sensor is placed in direct sunlight or close to other heat sources

Check the connection of the room sensor

DK EE

The room sensor is placed in the wrong room. The indoor setpoint is too low

Reconnect if the connection is lost

ES

Check placement of the room sensor according to installation instructions and change location if needed Check the placement of the room sensor and change room if needed. Change the temperature setpoint

FI

The room is too Check the indoor setpoint in the menu cold (or too warm in system cooling mode) The temperature displayed in the controller The room sensor may be influenced by Change location of the room sensor menu system changes after the room an external heat source sensor is moved The indicator on the mixing valve actuator The mixing valve does not open 1. Check that the mixing valve is does not change/move correctly installed

FR HR

2. Contact the installer The room is too Corresponding loop is warm (or cold, in warm (or too cold in cooling mode) even after a long period heating mode) without heat call (or cooling call)

A mixing valve does not close

The floor is cold

No heat demand from the underfloor heating system

HU

3. Replace the mixing valve 1. Check that the mixing valve is correctly installed

IT

2. Contact the installer 3. Replace the mixing valve

All rooms are cold (or too warm in cooling mode)

Disturbing noise from the pump at the same time and day of the week No communication

The room temperature OK but the floor is cold

The room is heated by another heat source Check the indoor setpoint in the menu The indoor setpoint is too low (or too system high, in cooling mode) ECO mode for the zone programmed in the ECO mode controller

Alarm shown in controller display

LT LV

Change the temperature setpoint

NL

Change ECO profile or assign another profile to the room/system

Pump exercise is active

Reduce the ECO setback value for the zone Change time for pump exercise

Communication error

Contact the installer

NO PL

Software versions incompatible

PT RO RU SE SK U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

151


UK

9.1 Troubleshooting after installation CZ DE

Problem

Indication

Probable cause

Solutions

The system does not start

The controller display is off

There is no AC power to the controller

1. Check that the controller is connected to AC power 2. Check the wiring 3. Check that there is 230 V AC power in the wall socket

DK EE

The sensors are faulty

ES

There is 230 V AC power in the wall socket

Blown controller fuse or faulty power cable

1. Replace the fuse and/or power cable and plug

The controller display continue flashing and an alarm is displayed

The cable is not connected or a wire is damaged

Check the wiring

9.2 Contact the installer For installer contact information, see the installation report in the end of this document. Prepare the following information before contacting an installer:

FI

• Installation report

FR

• Drawings of the underfloor heating system (if available)

HR

• List of all alarms, including time and date

9.3 Installer instructions

HU

To determine if a problem is caused by the supply system or the control system, loosen the actuators from the manifold for the room concerned, wait a few minutes and check if the flow pipe of the underfloor heating loop becomes warm.

IT LT LV

If the pipe does not become warm, the problem is in the heating system. If the loop becomes warm, the cause could be the room control system.

NL

A supply system defect can be indicated by no warm water in the manifold. Check the boiler and circulation pump.

NO PL PT RO RU SE SK 152

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK

10 Technical data

CZ DE

10.1 Technical data

DK

General IP ErP (with room sensors) Operating temperature Storage temperature Mounting standard microSD

EE IP20 (IP: degree of inaccessibility to active parts of the product and degree of water) III (VII) 0 °C to +50 °C -20 °C to +70 °C EN 50022, DIN 46277-3 micro SDHC, UHS/Standard

ES FI

4...32 GB, FAT 32 Class 4...10 +

FR

230 V AC ±10%, 50/60 Hz (maximum 125 mA) 12 V DC / 125 mA 24 V AC / 0.7A (maximum 6 A) 125 mA

HR

Power Supply Operating voltage Battery input (UPS) Transformer input Internal fuse

HU

Sensor inputs Supply temperature sensor Return temperature sensor Room temperature sensor Outdoor temperature sensor Ground temperature sensor (Snow and ice sensor) Moisture sensor (Snow and ice sensor)

NTC 10

IT

-50 °C...+100 °C, ±0.1 °C

LT ROFF = ∞ Ω

Relative humidity sensor

RON < 2MΩ UIN = 0...10V

Condensation sensor

0...100% RH UO < 5 V

LV NL

IO < 0.5 A ROFF > 11 kΩ

NO

RON < 1.6 kΩ Outputs Mixing valves

UO = 0...10V

Diverting valves

IO < 10 mA UO = 24 V AC

Snow sensor

PO < 10 VA UO = 24 V AC

Circulation pumps/Dehumidifiers

PO < 10 VA UIN = 230 V AC

PL PT RO

IIN ≤ 1 A

RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

153


UK Communication

CZ

BMS interface

MODBUS-RTU (RS-232)

Uponor Smatrix Base PRO bus

RJ45 Galvanically isolated

DE

Terminals: –, A, B

10.2 Technical specifications

DK

Cables Cable from controller to valve actuator (shielded connected to ground) Cable to sensor input on controller (shielded connected to ground) Cable from output on controller to external devices

EE ES

Standard cable length

Maximum cable length

0.75 m

20 m

0.2 mm² to 1.5 mm²

5m

100 m

0.6 mm²

5m

20 m

Up to 4.0 mm² solid, or 2.5 mm² flexible with ferrules

-

5m

0.5 mm² to 2.5 mm²

2m

20 m

Up to 4.0 mm² solid, or 2.5 mm² flexible with ferrules

Communication cable

FI

Power cable

Wire gauge

10.3 Controller layout

FR

B

C

D

HR HU IT

L M N

A

LT LV

E

F

G

H

I

J

K

NL Item

NO

Description

A

Display

B

Sensor input connection terminals

C

Mixing valve output connection terminals

D

Battery and transformer input connection terminals

E

microSD

F

BMS, MODBUS-RTU (RS-232), connection

G

Uponor Smatrix Base PRO bus connection terminals

H

Diverting valves/Snow and ice sensor output connection terminals

I

Circulation pump/Dehumidifier output connection terminals

J

Power connection connection terminal

RU

K

Fuse (125 mA)

L

Information button

SE

M

Navigation wheel/ OK button

N

Back button

PL PT RO

SK 154

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK

10.4 Wiring diagram, Uponor Smatrix Move PRO controller

3

CZ 24VAC

DE

2 1

DK

24VAC

EE 24VAC

ES FI 15VDC GND

FR

12VDC IN GND 24VAC IN 1 2 3 4 5 6 7 8 9

10 11 12 13 14 15 16 17 18

- +

- +

HR

- +

41 42 43 44 45 46 47 48 49

52 53 54 55 56

HU IT LT LV NL T

microSD

72 73

21 22 23 24 25 26

75 76

77 78

N L 125 mA 230 V ±10% 50/60 Hz

NO

- A B

≤ 1A PRO PRO

!

PL

I > 1A

!

L N ≤ 1A

PRO PRO

PT

L N

!

1 2

L N

RO

≤ 1A

PRO PRO

L N

RU

!

3

L N

SE SK U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

155


UK

10.5 Dimensions CZ

C ontroller X-159 90 mm

DE

45 mm

DK

50 mm

93 mm

214 mm

EE R oom

temperature sensor 80 mm

S-155

ES

60 mm

30 mm

85 mm

FI FR HR

R elative

humidity sensor 85 mm

S-157

60 mm

HU

85 mm

IT

26 mm

LT 50 mm

20 mm

LV S now

sensor

S-158

NL

63.5 mm

78 mm

NO PL 60 mm

32 mm

PT RO RU SE SK 156

U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK

11 Installation report

CZ DE DK EE ES FI Zone 1

Zone 2

Zone 3

FR Setup

Sensors

HR Supply temperature sensor

HU

Indoor temperature sensor Condensation sensor

IT

Relative Humidity sensor

LT

Stand Alone Control

Outdoor temperature sensor

LV Yes

Yes

Yes

No

No

No

Yes

Yes

Yes

No

No

No

Yes

Yes

Yes

No

No

No

Yes

Yes

Yes

No

No

No

Yes

Yes

Yes

No

No

No

Mixing Valve

NL NO

Diverting Valve

PL

Circulation pump

PT

Dehumidifier

RO

Heating/Cooling switch/external signal

RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

157


UK CZ DE Setup

DK

Zone 1

Zone 2

Zone 3

Yes

Yes

Yes

No

No

No

Yes

Yes

Yes

No

No

No

Yes

Yes

Yes

No

No

No

Yes

Yes

Yes

No

No

No

Yes

Yes

Yes

No

No

No

Sensors Supply temperature sensor

EE Condensation sensor

ES Mixing valve

Smartix Base PRO

FI FR HR

Diverting Valve

Circulation pump

HU

Dehumidifier

IT Heating/Cooling switch/external signal

LT PRO PRO

LV

Smatrix Base PRO controller Supply temperature sensor

NL

Return temperature sensor Outdoor temperature sensor

NO

Ground temperature sensor

Meltaway

PL PT

Moisture sensor 1

Primary return sensor

RO

Yes Mixing valve No

RU

Yes Circulation pump No

SE Snow and ice sensor

SK 158

U P O N O R S M AT R I X M O V E P R O ¡ I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L


UK CZ Zone 1

Setup

Zone 2

Zone 3

DE

Sensors

DK

Domestic Hot Water

Supply temperature sensor

EE Return temperature sensor

ES

Yes Mixing valve No

FI

Yes Circulation pump No

FR HR HU IT LT LV NL NO PL PT RO RU SE SK

U P O N O R S M AT R I X M O V E P R O · I N S TA L L AT I O N A N D O P E R AT I O N M A N U A L

159


Production: Uponor AB, MRY, Virsbo; Sweden 1088471 12_2016_EN

Uponor Corporation www.uponor.com

Uponor reserves the right to make changes, without prior notification, to the specification of incorporated components in line with its policy of continuous improvement and development.

Uponor iom smatrix move pro hc en 1088471 122016  

https://www.uponor.com/~/media/uponor-global/download-centre/smatrix/smatrix-pro/uponor_iom_smatrix_move_pro_hc_en_1088471_122016.pdf?versio...

Read more
Read more
Similar to
Popular now
Just for you