Page 1

Uponor Smatrix Base PRO EN QUICK GUIDE

07 | 2016


QUICK GUIDE EN CZ

Contents

Uponor Smatrix Base PRO components

Uponor Smatrix Base PRO components........................2

An Uponor Smatrix Base PRO system may be a combination of the following components:

DE System example.................................................................2

DK

Copyright and disclaimer...............................................3 Preface...........................................................................4

EE

Safety instructions.............................................................4 Correct disposal of this product (Waste Electrical and Electronic Equipment)........................................................4

ES

Quick Guide....................................................................5 Interface and thermostat operating instruction..................5 Communications protocol..................................................5 Installation.........................................................................7 Register thermostat and/or system device to a controller..9 Register multiple controllers.............................................10 Unregister one channel or system device.........................10 Unregister all channels.....................................................10 Room bypass....................................................................10 Other functions................................................................10

FI FR HR

Technical data..............................................................11

• Uponor Smatrix Base PRO Controller X-147 (controller) • Uponor Smatrix Base PRO Interface I-147 (interface) • Uponor Smatrix Base Thermostat Standard T-145/T-145 POD (standard thermostat T-145/T-145 POD) • Uponor Smatrix Base Thermostat Dig T-146 (digital thermostat T-146) • Uponor Smatrix Base PRO Thermostat D+RH T‑147 (digital thermostat T-147) • Uponor Smatrix Base Thermostat Prog.+RH T-148 (digital thermostat T-148) • Uponor Smatrix Base Thermostat Public T‑143 (public thermostat T-143)

HU IT

• Uponor Smatrix Base Thermostat Flush T-144 (flush thermostat T-144)

LT

• Uponor Smatrix Base Slave Module M-140 (slave module M-140) • Uponor Smatrix Base Star Module M-141 (star module M-141)

LV

• Uponor Smatrix Transformer A-1XX (transformer A-1XX)

NL

System example NO PL PT Uponor Smatrix Uponor Smatrix Base/Base PRO Uponor Smatrix Base/Base PRO E N I N S TA L L AT I O N A N D O P E R AT I O N MANUAL PRO E N Base/Base I N S TA L L AT I O N A N D O P E R AT I O N

RO

1

2

3

4

MANUAL E N I N S TA L L AT I O N A N D O P E R AT I O N MANUAL

06 | 2016 06 | 2016 06 | 2016

RU

1

2

3

4

https://www.uponor.com/smatrix/downloads.aspx

SE SI SK 2

U P O N O R S M AT R I X B A S E P R O · Q U I C K G U I D E


QUICK GUIDE EN

Copyright and disclaimer

CZ DE

Uponor has prepared this installation and operation manual and all the content included solely for information purposes. The contents of the manual (including graphics, logos, icons, text, and images) are copyrighted and protected by worldwide copyright laws and treaty provisions. You agree to comply with all copyright laws worldwide in your use of the manual. Modification or use of any of the contents of the manual for any other purpose is a violation of Uponor’s copyright, trademark and other proprietary rights. The presumption for the manual is that the safety measures have been fully complied with and, further, that Uponor Smatrix Base PRO, including any components that are part of such system, covered by the manual: • is selected, planned and installed and put into operation by a licensed and competent planner and installer in compliance with current (at the time of installation) installation instructions provided by Uponor as well as in compliance with all applicable building and plumbing codes and other requirements and guidelines; • has not been (temporarily or continuously) exposed to temperatures, pressure and/or voltages that exceed the limits printed on the products or stated in any instructions supplied by Uponor; • remain in its originally installed location and is not repaired, replaced or interfered with, without prior written consent of Uponor;

While Uponor has made efforts to ensure that the manual is accurate, Uponor does not guarantee or warrant the accuracy of the information contained herein. Uponor reserves the right to modify the specifications and features described herein, or discontinue manufacture of Uponor Smatrix Base PRO described at any time without prior notice or obligation. The manual is provided “as is” without warranties of any kind, either expressed or implied. The information should be independently verified before using it in any manner.

DK EE ES FI

To the fullest extent permissible, Uponor disclaims all warranties, expressed or implied, including, but not limited to, the implied warranties of merchantability, fitness for particular purpose and non-infringement.

FR HR

This disclaimer applies to, but is not limited to, the accuracy, reliability or correctness of the manual.

HU

Under no circumstances shall Uponor be liable for any indirect, special, incidental or consequential damages or loss that result from the use of or the inability to use the materials or information in the manual, or any claim attributable to errors, omission or other inaccuracies in the manual, even if Uponor has been advised of the possibility of such damages.

IT LT LV

This disclaimer and any provisions in the manual do not limit any statutory rights of consumers.

NL

• is connected to potable water supplies or compatible plumbing, heating and/or cooling products approved or specified by Uponor;

NO

• is not connected to or used with non-Uponor products, parts or components except for those approved or specified by Uponor; and

PL

• does not show evidence of tampering, mishandling, insufficient maintenance, improper storage, neglect or accidental damage before installation and being put into operation.

PT RO RU SE SI SK

U P O N O R S M AT R I X B A S E P R O · Q U I C K G U I D E

3


QUICK GUIDE EN

Preface

CZ DE

This quick start guide to serves as a reminder for experienced installers. We strongly recommend reading the full manual before installing the control system.

DK

Safety instructions

EE

Warnings used in this manual

ES

The following symbols are used in the manual to indicate special precautions when installing and operating any Uponor equipment:

FI

W arning ! Risk of injury. Ignoring warnings can cause injury or damage components.

FR

C aution !

HR

Ignoring cautions can cause malfunctions. Safety measures

HU

Conform to the following measures when installing and operating any Uponor equipment:

IT

• Read and follow the instructions in the installation and operation manual.

LT

• Installation must be performed by a competent person in accordance with local regulations.

LV

• It is prohibited to make changes or modifications not specified in this manual.

NL

• All power supply must be switched off before starting any wiring work.

Correct disposal of this product (Waste Electrical and Electronic Equipment) N OT E ! Applicable in the European Union and other European countries with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed with other household wasted at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes of disposal.

• Do not use water to clean Uponor components.

NO

• Do not expose the Uponor components to flammable vapours or gases.

PL

We cannot accept any responsibility for damage or breakdown that can result from ignoring these instructions.

PT Power

RO

W arning !

RU

The Uponor system uses 50 Hz, 230 V AC power. In case of emergency, immediately disconnect the power. Technical constraints

SE C aution ! To avoid interference, keep installation/data cables away from power cables of more than 50 V.

SI SK 4

U P O N O R S M AT R I X B A S E P R O · Q U I C K G U I D E


QUICK GUIDE EN

Quick Guide

CZ DE W arning !

N OT E ! This is a quick start guide to serve as a reminder for experienced installers. We strongly recommend reading the full manual before installing the control system.

DK

Electrical installation and service behind secured 230 V AC covers must be carried out under the supervision of a qualified electrician.

EE ES

GPI 1

GPI

AB + - AB + - AB + - AB - AB -

FI

M-141*

GPI 2

FR HR

GPI 3

X-147

HU

M-140*

IT

* The illustration shows an installation example, with options.

Communications protocol

LT The wide array of connection possibilities presented with this communications protocol can be combined in any way best suited for the current system.

The system is based on a bus communications protocol (requires the thermostats unique ID to be registered to the controller), utilising daisy chain, direct or star topology connections. This allows serial and parallel connections, makes wiring and connection of thermostats and system devices much easier than connecting one thermostat per connection terminal.

LV NL NO

Interface and thermostat operating instruction I-147

T-148 T-147 T-146

T-145

T-144

T-143

PL PT

20

5

35

RO RU SE SI SK U P O N O R S M AT R I X B A S E P R O ¡ Q U I C K G U I D E

5


QUICK GUIDE EN

A

CZ

B

X-147 M-140*

DE DK EE

2

ES

1

*Option

C

FI

D

X-147 M-140*

3

FR

2

3

HR

M-141*

3

2

1 A B + - A B + - A B + -

IT *Option

LT

1

F T-143

4

ON

DIP

G

NL

2

T-148 T-147 1 T-146 T-143

PL

3

1

2

I

A B - A B -

N L

Option

J

K

1

A B -

1

Option

RO

I-147

3

3

PT

H

X-147

X-147 M-140* M-141*

1 2 3 4

NO

A B + -

2

*Option

E

LV

3

T-144

1

A B + - A B + -

HU

1

2

3 1

T-148 T-147 T-146 T-145 T-143

L

RU

2

T-148 T-147 T-146

SE X-147 SI

X-147

T-148

3s

SK 6

U P O N O R S M AT R I X B A S E P R O · Q U I C K G U I D E


QUICK GUIDE EN

Installation W arning !

E. Connect optional external sensor (compatible thermostats only) and set the DIP switch (public thermostat T-143 only).

The transformer module is heavy and might detach if the controller is held upside down without the cover on.

Switch

N OT E ! Connect only one actuator for each channel. Channels 01 and 02 have double outputs (a and b) for two actuators.

C aution ! Ensure that each actuator is connected to the correct channel so that the thermostats are controlling the correct loops.

C aution ! The switches in the public thermostat must be set before the thermostat is registered.

C aution ! The switches, in the public thermostat, must be set to one of the available functions, otherwise it cannot be registered. A. Attach the full assembly, or parts of it, to the wall either with a DIN rail or by using wall screws and plugs. B. Connect the actuators. C. Connect a thermostat communication cable to the controller, slave module, and/or the optional star module. Note: Daisy chain bus topology is recommended. See page 5, Communications protocol for more information. D. Connect a thermostat communication cable to the thermostat/timer.

1

2

3

4

Standard room thermostat

Off

Off

Off

Off

Standard room thermostat together with a floor temperature sensor

On

Off

Off

Off

Function*

N OT E ! Wires between transformer and controller card needs to be disconnected prior to detaching.

N OT E ! Registration of at least one thermostat must be done before registering a system device.

CZ DE DK EE

Standard room thermostat, or system device, together with an outdoor temperature sensor

Off

System device together with a supply temperature sensor for heating/cooling switch over function

Off

Off

On

Off

System device where the sensor input is used for Comfort/ECO switch over function

Off

Off

Off

On

FR

Remote sensor

Off

On

Off

On

HR

On

Off

Off

ES FI

* The thermostat can only be registered as a system device to a Base PRO system with multiple controllers, if it is registered to the master controller.

HU

F. Check that all wiring is complete and correct:

IT

• Actuators • Heating/cooling switch • Circulation pump

LT

G. Connect a system bus communication cable in between controllers and route one cable to the interface. Note: Daisy chain bus topology is recommended. See page 5, Communications protocol for more information.

LV NL

H. Connect a system bus communication cable (1) and a power cable (2) to the interface. I. Ensure that the 230 V AC compartment of the controller is closed and the fixing screw is tightened.

NO

J. Connect the power cable to a 230 V AC wall socket, or if required by local regulations, to a junction box.

PL

K. Set time and date on thermostats and timer (digital thermostat T-148 and timer only).

PT

L. Select thermostat control mode (settings menu 04, in digital thermostats only). Default: RT (standard room thermostat).

RO

M. Register thermostats, the timer and other system devices, in that order (next page).

RU SE SI SK

U P O N O R S M AT R I X B A S E P R O · Q U I C K G U I D E

7


QUICK GUIDE EN

1

CZ

2.1

2.2

2.3 2.1

DE DK

3s

EE

3

2.2

T-143 T-146 T-147 T-148

ES

T-144

5s

T-145

FI

5s

5s

FR

5s

HR

4

5.1

2

5.2

5.3

HU

3

IT LT

6

5.4

LV

6.1

T-143

NL

5s

I-147 NO

6.2

PL

Français

Svenska

English

Português

6.1 Italiano

Deutsch

Suomi

Español

Link Touch Screen to controller

Unlink controller

PT

6.3

RO

Link Touch Screen to controller

Link OK

Unlink controller

RU

7

SE SI

5

6

8 3s

SK 8

U P O N O R S M AT R I X B A S E P R O · Q U I C K G U I D E


QUICK GUIDE EN

Register thermostat and/or system device to a controller N OT E ! At least one thermostat must be registered before registering a system device. To register room thermostats and system devices (interface etc.) to the controller:

The selected channel LED in the controller turns fixed green and the registration is complete.

Register a thermostat 2. Select a thermostat channel.

2.1 Use buttons < or > to move the pointer (LED flashes red) to a preferred channel.

2.2 Press the OK button to select the channel for registration. The LED for the selected channel starts flashing green.

2.3 Repeat steps 2.1 and 2.2 until all channels to be registered with the thermostat are selected (LEDs flashing green).

Note! It is recommended to register all channels to the thermostat at the same time.

5. Make sure to be in registration mode (step 1).

5.1 Use buttons < or > to move the pointer to the power LED (LED flashes red).

DK

5.2 Press the OK button to enter system channel registration mode. The power LED flashes according to the pattern long blink, short pause, long blink and channel 1 LED flashes red.

EE

1 = Touch screen interface

2 = Not used

3 = Public thermostat with outdoor sensor

4 = Public thermostat with heating/cooling switch from sensor input.

5 = Public thermostat with Comfort/ECO switch

THERMOSTAT T-143 AS A THERMOSTAT, WITH VARIOUS FUNCTIONS

INTERFACE I-147

3.1 Gently press and hold the registration button on the thermostat, release when the LED starts flashing green (located in the hole above the registration button). The selected channel LED in the controller turns fixed green and the registration is complete.

6.1. Power up the interface and attach it to the charger.

6.2. Follow the startup guide in the interface up until registration.

THERMOSTAT T-144

3.1 Using a pointed instrument, gently press and hold the registration button on the thermostat, release when the LED above the dial starts flashing. The selected channel LED in the controller turns fixed green and the registration is complete.

THERMOSTAT T-145

3.1 Gently press and hold the registration button on the thermostat, release when the LED on the front of the thermostat starts flashing. The selected channel LED in the controller turns fixed green and the registration is complete.

FI FR HR

5.4 Press the OK button to select system device channel. The channel LED starts flashing green

3. Select a thermostat.

ES

5.3 Select a system channel, see list below.

6. Select a system device matching the system channel.

DE

Register a system device (I-147 etc)

Enter registration mode 1. Press and hold the OK button on the controller, for about 3 seconds, until the LED for channel 1 (or the first unregistered channel) flashes red.

CZ

4. Repeat steps 2 and 3 until all available thermostats are registered.

HU IT LT LV

6.3 Press Link Touch Screen to controller in the Startup guide, or Link menu (Main menu > Preferences), to initialize registration.

NL

6.4 The interface gets registered to the controller. The selected channel LED in the controller turns fixed green and the registration is complete.

THERMOSTAT T-143 AS A SYSTEM DEVICE, WITH VARIOUS FUNCTIONS

6.1 Gently press and hold the registration button on the thermostat, release when the LED starts flashing green (located in the hole above the registration button). The selected channel LED in the controller turns fixed green and the registration is complete.

NO PL PT RO

7. Repeat steps 5 and 6 until all available system devices are registered.

THERMOSTATS T-146, T-147 AND T-148

Exit registration mode

3.1 Press and hold both - and + buttons on the thermostat until the text CnF (configure) and a communication icon is displayed.

8. Press and hold the OK button on the controller, for about 3 seconds, until the green LEDs turn off to end registration and return to run mode.

RU SE SI SK

U P O N O R S M AT R I X B A S E P R O ¡ Q U I C K G U I D E

9


QUICK GUIDE EN CZ

Register multiple controllers

Unregister all channels

Up to 16 controllers can be registered to an interface.

When one or more channels are inaccurately registered, it is possible to remove all registrations at the same time.

All additional controllers in the system must be registered to the interface.

DE

N OT E ! At least one thermostat must be registered to the additional controller before registering to the interface.

DK EE

See steps 5 and 6 in the “Register thermostat and/ or system device to a controller” section for more information.

ES

Unregister one channel or system device When a channel or system device is inaccurately registered or if a thermostat registration needs to be redone, it is possible to remove the current registration from the controller.

FI FR

N OT E ! The controller must be unregistered in the interface as well. Go to menu Main menu > Preferences > Link and unregister.

HR HU

To unregister a channel: 1. Enter registration mode. Channel 1 LED flashes red/ green, or the first unregistered channel flashes red.

IT

LV

2. If a system device (timer etc) is to be unregistered, enter system channel registration mode. The power LED flashes according to the pattern long blink, short pause, long blink and channel 1 LED flashes red/green.

NL

3. Use buttons < or > to move the pointer (LED flashes red) to the selected channel (flashes green if registered) to unregister.

LT

N OT E ! The controller must be unregistered in the interface as well. Go to menu Main menu > Preferences > Link and unregister. To cancel all channel registrations: 1. Enter registration mode. Channel 1 LED flashes red/ green, or the first unregistered channel flashes red. 2. Press the < and > buttons simultaneously for about 10 seconds until the LEDs for all channels except one turn off. The one remaining flashes red.

Room bypass To reach the bypass settings, the controller must be registered to the interface. 1. In the interface, go to the Room bypass menu, Main menu > System settings > Room bypass. 2. Select a controller. 3. Select up to a maximum of two rooms. 4. Press the Confirm button to save and exit the menu.

Other functions See full manual for more information about Autobalancing of actuators (eliminating the need of manual balancing,on by default), Heat pump integration, Cooling, Comfort/ECO settings, KNX module, Room check, and Supply check etc.

4. Press the < and > buttons simultaneously for about 5 seconds until the LED for the selected channel starts flashing red.

NO PL PT RO RU SE SI SK 10

U P O N O R S M AT R I X B A S E P R O · Q U I C K G U I D E


QUICK GUIDE EN

Technical data

CZ

General IP Max. ambient RH (relative humidity)

IP20 (IP: degree of inaccessibility to active parts of the product and degree of water) 85% at 20 °C

DE

Thermostat CE marking ERP (thermostat only) Low voltage tests EMC (electromagnetic compatibility requirements) tests Power supply Voltage Operating temperature Storage temperature Connection terminals (thermostats only)

DK IV EN 60730-1* and EN 60730-2-9*** EN 60730-1 From controller 4.5 V to 5.5 V 0 °C to +45 °C -10 °C to +70 °C 0.5 mm² to 2.5 mm²

EE ES FI

Interface CE marking Low voltage tests EMC (electromagnetic compatibility requirements) tests Power supply Operating temperature Storage temperature

FR

EN 60730-1 and EN 60730-2-1 EN 60730-1 230 V AC +10/-15%, 50 Hz in wall box or mini USB connection 0 °C to +45 °C -20 °C to +70 °C

HR HU

Controller/interface SD card Type Capacity Speed

micro SDHC, UHS or Standard 4 GB to 32 GB, FAT 32 formatting Class 4 to 10 (or higher)

IT LT

Controller CE marking ERP Low voltage tests EMC (electromagnetic compatibility requirements) tests Power supply Internal fuse Operating temperature Storage temperature Maximum consumption Pump and boiler relay outputs General purpose input (GPI) Heat pump input Heat pump output Valve outputs Power connection Connection terminals for power, pump, GPI and boiler Connection terminals for bus communication Connection terminals for valve outputs *) EN 60730-1 Automatic electrical controls for household and similar use -- Part 1: General requirements **) EN 60730-2-1 Automatic electrical controls for household and similar use -- Part 2-1: Particular requirements for electrical controls for electrical household appliances ***) EN 60730-2-9 Automatic electrical controls for household and similar use -- Part 2-9: Particular requirements for temperature sensing controls

VIII EN 60730-1* and EN 60730-2-1** EN 60730-1 230 V AC +10/-15%, 50 Hz or 60 Hz T5 F3.15AL 250 V, 5x20 3.15A quick acting 0 °C to +45 °C -20 °C to +70 °C 45 W 230 V AC +10/-15%, 250 V AC 8 A maximum Only dry contact 12 – 24 V DC /5 – 20 mA 5 – 24 V DC /0.5 – 10 mA, current sink ≤ 100 mW 24 V AC, 0.2 A average, 0.4 A peak 1 m cable with europlug (except UK) Up to 4.0 mm² solid, or 2.5 mm² flexible with ferrules 0.5 mm² to 2.5 mm² 0.2 mm² to 1.5 mm²

LV NL NO PL PT RO RU

Usable in all Europe Declaration of conformity: We hereby declare under our own responsibility that products dealt with by these instructions satisfy all essential demands linked to the R&TTE 1999/5/CE Directive dated March 1999.

SE SI SK

U P O N O R S M AT R I X B A S E P R O · Q U I C K G U I D E

11


Production: Uponor AB, MRY, Virsbo; Sweden 1087356 07_2016_EN

Uponor Corporation www.uponor.com Uponor reserves the right to make changes, without prior notification, to the specification of incorporated components in line with its policy of continuous improvement and development.

Uponor qg smatrix base pro  

https://www.uponor.com/~/media/uponor-global/download-centre/smatrix/smatrix-pro/uponor-qg-smatrix-base-pro.pdf?version=2

Read more
Read more
Similar to
Popular now
Just for you