Issuu on Google+

TECHNICAL BULLETIN ®

ULTERION 8080

DURABLE PRESS RESIN PERFORMANCE FEATURES

MARKET USES

 

 

Low concentrations perform effectively giving excellent shrinkage control and appearance ratings. Wide choice of cure conditions provides opportunity to increase efficiency of finishing range while maintaining fabric performance. Excellent durability to laundering; maintains shrinkage control and appearance over extended washings, both home and industrial. Chlorine retention is low avoiding physical damage and discoloration when fabric is laundered and bleached. Highly concentrated - reduces shipping and usage costs

Product Description

Handling / Storage Stability

Ulterion® 8080 is a commercially pure, concentrated, unbuffered glyoxal-based reactant. It can be used with a variety of accelerators in pre-cure finishing processes. Ulterion® 8080 reactant may be cured over a wide range of cure conditions from 290°F to 410°F (143°C – 210°C).

Ulterion® 8080 should be used in a well ventilated working area. Wear suitable clothing and impervious gloves to prevent skin contact. Use chemical splash-proof goggles for operations where face and eye contact can occur. Use of a respirator is recommended where exposures exceed PEL or are unknown.

Typical Properties Solids, % pH, Value Appearance Density lb/gal. Origin

80 4.5 Slightly Yellow Liquid 11.5 USA

Typical Formulation Ulterion® 8080 reactant Magnesium Chloride* Ulterion International, Inc. Polyethylene Nonionic Softener P.O. Box 490 Polyethylene Cationic Softener Pendergrass, GA 30567 Nonionic/Non- Rewetting surfactant Telephone (706) 693-4900 Fax (706) 693-0052

www.ulterion.com

Denim finishing Textile finishing

% On Bath Wt. 3-7 2-4 1-3 2-4 0.1 - 0.5

*Magnesium Chloride is an Accelerator and should be used at 40% on reactant weight

In case of spill, cover the material with an inert absorbent, sweep up and place in a waste disposal container. Flush the area well with water. Storage stability is at least 6 months at 100°F (38°C). Will remain fluid and perform satisfactorily if held between 15°F (-10°C) and 120°F (49°C), but will darken slowly if held above 90°F (32°C).

Product Safety Liquid may be irritating to the skin, eyes and other tissues. Repeated dermal exposure may cause irritation or an allergic skin reaction. Vapor inhalation may cause irritation of the

The information contained herein is thought to be accurate in all aspects; however, the applications for these products mentioned are presented without guarantee or responsibility as to the suitability of our products whether used singly or in combination with other products. Nothing herein is to be taken as a license to operate under or as a recommendation to infringe any patents. The products are sold without warranty, expressed or implied, and are purchased at buyer’s risk.


TECHNICAL BULLETIN

ULTERION® 8080

DURABLE PRESS RESIN Application Methods

eyes and respiratory tract.

Make sure fabrics treated with Ulterion® 8080 reactant are neutral and relatively free of other processing agents. The presence of residual alkalinity in excess of 0.05% NaOH may cause yellowing and reduced shrinkage control.

Inhalation of formaldehyde vapor has been shown to produce cancer in laboratory animals.

Recommended Cure Conditions Time and temperature are optional depending upon equipment, although a minimum temperature of 325°F (163°C) is recommended for cure.

When considering the use of Ulterion International products, please refer to the latest Material Safety Data Sheets (MSDS). If you require an MSDS for this product; please call (770) 579-0552 or your Ulterion International Representative.

Recommended Bath Preparation  Add diluted wetting agent to about 50 gal. of water at 70°F - 110°F (21°C – 43°C).  Add Ulterion® 8080 reactant, with thorough stirring.  Dilute the softener(s) with warm water and add to bath with stirring.  Dilute the accelerator 1:1 with water and add to the bath with stirring.  Bulk to 100 gallons.

Recommendations for Successful Resin Finishing  Fabric must be suitable for end use.  Unfinished fabric tensile >30% of the finished tensile.  Bleached and dyed fabric must be clean and absorbent.  Fabric alkalinity <0.05% as NaOH.  Fabric pH should be 6.5-7.5.  Wetting speed <= 5 sec. @ 70-80°F.  Use reactant/cat stable components.  Use minimum tension in finishing.  Use accurate finish mixing procedures.  Control of all major variables in process. Ulterion International, Inc.  Wet-pick-up should be 60 - 75% OWG at the P.O. Box 490 resin pad. Pendergrass, GA 30567 Telephone (706) 693-4900 Fax (706) 693-0052

www.ulterion.com

The information contained herein is thought to be accurate in all aspects; however, the applications for these products mentioned are presented without guarantee or responsibility as to the suitability of our products whether used singly or in combination with other products. Nothing herein is to be taken as a license to operate under or as a recommendation to infringe any patents. The products are sold without warranty, expressed or implied, and are purchased at buyer’s risk.


Ulterion 8080