Issuu on Google+


BEFORE PLANNING YOUR HANDLE-LESS KITCHEN PLEASE CONSIDER THE ITEMS LISTED BELOW

BASE UNITS 1: ALL BASE & TALL UNITS WITH EXPOSED END PANELS WILL NEED TO BE COVERED WITH DECOR PANEL , NO PLINTH RETURNS TO BE SPECIFIED, ALWAYS USE DECOR PANELS. THE DECOR PANELS WILL BE USED TO COVER THE ENDS OF THE ALUMINIUM TRIMS. 2: DRAWER PACKS ARE ONLY AVAILABLE IN 500, 600, 800 & 1000mm WIDE, USING TWO 140mm & ONE 355mm HIGH DRAWERS. ‘DO NOT SPECIFY 300mm OR 400mm WIDE DRAWER PACKS AS THE DRAWER FRONTS ARE NOT AVAILABLE’ IN THESE SIZES. 3: NEW WORKTOP HEIGHT FOR HANDLE-LESS KITCHENS, THIS WILL BE SET AT 942mm, FROM THE FLOOR TO THE TOP EDGE OF THE WORKTOP. 4: ALL BASE UNIT DECOR PANELS, INFILL PANELS & FLY END PANELS WILL BE HIGHER TO SUIT THE NEW HEIGHT WORKTOP. 5: BASE OVEN HOUSING UNIT 4615 THAT USES A STANDARD SIZE SINGLE OVEN WILL HAVE TWO SMALL OVEN INFILL PANELS,

ONE PANEL FITTED ABOVE THE OVEN & ONE PANEL FITTED BELOW THE OVEN. 6: NEW FITTING POSITION FOR THE S’FRAME FRONT STRIP, POSITIONED FORWARD FLUSH WITH THE ADJACENT DOOR.

TALL UNIT 1: TALL UNIT HEIGHT TO SUIT 720mm WALL UNITS = 1970mm WITH PLINTH 2120mm. 2: TALL UNIT HEIGHT TO SUIT 900mm WALL UNITS = 2150mm WITH PLINTH 2300mm. 3: EXPOSED ENDS & END OF RUN TALL UNITS ‘DO NOT USE PLINTH RETURNS’ ALWAYS USE DECOR PANELS. THE DECOR PANELS WILL BE USED TO COVER THE ENDS OF THE ALUMINIUM TRIMS. 4: THE FRIDGE FREEZER HOUSING UNIT MUST BE SPECIFIED WITH VERTICAL ALUMINIUM TRIM TO ALLOW FOR ACCESS TO THE DOOR HANDLES PLEASE SEE PAGE 11 5: PLEASE SEE PAGE 10 FOR FULL DETAILS ON ALL TALL HOUSING UNITS 6: PLEASE NOTE: SHORT BASE UNIT DOORS WILL NO LONGER BE AVAILABLE FOR TALL HOUSING UNITS OR BASE UNITS 7: TO ALLOW FOR THE TOP DOORS OF THE OVEN HOUSING UNITS TO OPEN THE UNITS WILL BE FITTED WITH PUSH-FIT HINGES AND CATCHES.

WALL UNITS 1: ALL WALL UNITS HAVE TWO BOTTOM PANELS TO ALLOW FOR A FINGER RECESS TO OPEN THE DOORS. 2: THE NEW BOTTOM PANEL WILL BE AVAILABLE IN TWO OPTIONS. OPTION ONE: MADE WITH RECESSED LIGHTING WITH CHANNELS FOR CONCEALING THE LIGHTING WIRES OPTION TWO: MADE WITH OUT THE CHANNELS FOR CONCEALING THE LIGHTING WIRES

2

MANHATTAN SPECIFIER’S GUIDE


DETAILS SHOWING THE END ELEVATION OF HANDLE-LESS KITCHEN UNITS & HANDLE TRIM CONFIGURATIONS Top hung door opening with push catches Panel WORKTOP TRIM

DRAWER / DOOR TRIM

Top hung door opening with push catches Panel

Microwave Single oven

458mm

WALL UNITS SHOWING FINGER PULL

DRAWER PACK SHOWING DRAWER TRIM

2120mm

Single oven Panel Panel

BASE UNIT SHOWING THE WORKTOP TRIM

Long door Drawer pack

BASE UNITS DETAIL SHOWING THE HANDLESS TRIMS for LONG DOOR UNITS AND DRAWER PACK UNITS

HOUSING UNITS SHOWING THE HANDLESS TRIMS

440.00

WALL NOGGINS TO SUIT MANHATTAN’S RANGE OF KITCHEN UNITS. NOTE: WALL UNIT NOGGINS SHOULD BE A MINIMUM OF 440mm HIGH.

720 Wall Unit

575 Wall Unit

360 Wall Unit

900 Wall Unit 360 Wall Unit

Base Unit

Base Unit

Base Unit

Base Unit

Base Unit

2286.00 1561.00

1470.00

Housing Unit & Broom Units

918.00 NEW HEIGHT 839.00

1654.00

1619.00

2286.00

1846.00

Stainless Steel Hood

Base Unit

SIDE ELEVATION

UNDER WORKTOP APPLIANCE SPACE HEIGHTS

Top fixing panel

The space required for appliances that fit under worktops. With Handle-less kitchens the aluminium trim will run across the top of the appliance space, this will restrict the height for a number of appliances. The maximum height for appliances will be 847mm from the floor to the under side of the aluminium trim with the plinth set at 150mm high. Where appliances need a top fixing, a panel will need to be specified to allow for the fixing. This will change the maximum height for the appliance space to 831mm. The panel can be made from plinth material or can be specified as a 9036 panel size = 600mm x 200.8mm made from 16mm MFC with edging to the long edges

815mm TO 847mm

815mm TO 831mm

MANHATTAN SPECIFIER’S GUIDE

3


BASE UNITS

WIDTH

568 DEEP

300

800 900 1000 1200

Lt Hd 2077 Rt Hd 2078 Lt Hd 2079 Rt Hd 2080 Lt Hd 2081 Rt Hd 2082 Lt Hd 2083 Rt Hd 2084 Lt Hd 2085 Rt Hd 2086 2087 2088 2089 2090

BASE CORNER UNIT

WIDTH

568 DEEP

With full-height door

600 (min 336–378) 800 (min 236–278) 1000 (min 136–178) 1200 (min 36–78) **800 (min 286–328) *800 (min 336–378) *1000 (min 236–278) *1200 (min 236–278)

Lt Hd 2091 Rt Hd 2092 Lt Hd 2093 Rt Hd 2094 Lt Hd 2095 Rt Hd 2096 Lt Hd 2097 Rt Hd 2098 Lt Hd 2099 Rt Hd 2100 Lt Hd 2101 Rt Hd 2102 Lt Hd 2103 Rt Hd 2104 Lt Hd 2105 Rt Hd 2106

With full-height door

Door height 715mm

400 450 500 600 With full-height doors

Door height 715mm

600mm WIDE UNIT (300mm Wide door)

800mm WIDE UNIT (400mm Wide door)

1000mm WIDE UNIT (500mm Wide door)

1200mm WIDE UNIT (600mm Wide door)

**800mm WIDE UNIT (450mm Wide door)

*800mm WIDE UNIT (500mm Wide door)

*1000mm WIDE UNIT (600mm Wide door)

*1200mm WIDE UNIT (2 X 400mm Wide doors)

NOTE: MIN & MAX POSITIONS FROM THE WALL WITH THE FRONT STRIP SET IN THE VERTICAL POSITION RESULTING IN 636MM FROM THE OPPOSING WALL.

BASE BOTTLE STORAGE UNIT With full-height, pull-out door

Door height 715mm

DOOR TO MATCH RANGE

WIDTH

568 DEEP

150

2142

NOTE: IDEALLY TO BE FITTED EITHER SIDE OF A HOB OR BASE OVEN HOUSING UNIT. NOTE: 2700 UNIT - ONLY AVAILABLE WITH A STAINLESS STEEL DOOR. NOTE: 2719 UNIT - THE STYLE OF THE DOOR WILL DIFFER ACCORDING TO THE RANGE.

BASE UNIT S’FRAME

PLEASE NOTE: 1: THE TOP EDGE OF THE S’FRAME MID STRIP WILL HAVE TO BE NOTCHED ON SITE BY THE FITTER AFTER FINAL ADJUSTMENT OF THE S’FRAME. THIS MODIFICATION IS TO ALLOW FOR THE ALUMINIUM TRIM TO RUN BEHIND THE S’FRAME.

MID STRIP NOTCH

2: THE S’FRAME FRONT STRIP TO BE POSITIONED FLUSH WITH FRONT FACE OF THE ADJACENT DOOR, THIS MODIFICATION IS TO ALLOW FOR THE ALUMINIUM TRIM TO RUN BEHIND THE S’FRAME.

FRONT STRIP

4

MANHATTAN SPECIFIER’S GUIDE


BASE SINK UNITS With full-height door

WIDTH WIDTH

316 DEEP 568 DEEP

500

Lt Hd 2107 Rt Hd 2108 Lt Hd 2109 Rt Hd 2110

Door height 715mm

600

With full-height doors

Door height 715mm 800 900 1000 1200

2111 2112 2113 2114

WIDTH 568 DEEP 800 (min 236–278) **800 (min 286–328) 1000 (min 136–178) 1200 (min 36–78) *800 (min 336–378) *1000 (min 236–278) *1200 (min 236–278)

568 DEEP

WIDTH

568 DEEP

500 600 800 900 1000 1200

6705 6706 6708 6709 6710 6712

SINK BOTTOM LINERS

WIDTH

CODE

Optional extra

500 600 800 900 1000 1200

FACM355A FACM349A FACM350A FACM356A FACM351A FACM357A

BASE SINK CORNER UNITS WIDTH With full-height door

800mm WIDE UNIT (400mm Wide door)

**800mm WIDE UNIT (450mm Wide door)

1000mm WIDE UNIT (500mm Wide door)

*800mm WIDE UNIT (500mm Wide door)

*1000mm WIDE UNIT (600mm Wide door)

*1200mm WIDE UNIT (2 X 400mm Wide door)

1200mm WIDE UNIT (600mm Wide door)

Lt Hd 2115 Rt Hd 2116 Lt Hd 2117 Rt Hd 2118 Lt Hd 2119 Rt Hd 2120 Lt Hd 2121 Rt Hd 2122 Lt Hd 2125 Rt Hd 2126 Lt Hd 2127 Rt Hd 2128 Lt Hd 2129 Rt Hd 2130

NOTE: MIN & MAX POSITIONS FROM THE WALL WITH THE FRONT STRIP SET IN THE VERTICAL POSITION RESULTING IN 636MM FROM THE OPPOSING WALL.

BASE SINK BACK PANELS Optional extra

Height 430mm

MANHATTAN SPECIFIER’S GUIDE

5


BASE CORNER UNITS - WITH PULL-OUT ‘MAGIC CORNER’ MECHANISM

WIDTH

568 DEEP

With full-height door

1000 (min 136-178) *1000 (min 236-278)

Lt Hd 2131 Rt Hd 2132 Lt Hd 2133 Rt Hd 2134

CORNER BASE UNIT WITH LE MANS STORAGE MECHANISM

WIDTH

CODE

The Le Mans storage shelves move completely out of the unit for easy access to both shelves

1000 (min 136-178)

Lt Hd 2135 Rt Hd 2136

KITCHEN ACCESSORY - HALF CIRCLE, FULL EXTENSION CAROUSELS

SIZE

CODE

Carousels for use in corner units

000 X 000

MECH100A

HEIGHT

WIDTH

CODE

VARIABLE

VARIABLE

9036

1000mm WIDE UNIT (500mm Wide door)

Carcase height 720mm Door height 715mm

*1000mm WIDE UNIT (600mm Wide door)

NOTE: MIN & MAX POSITIONS FROM THE WALL WITH THE FRONT STRIP SET IN THE VERTICAL POSITION RESULTING IN 636MM FROM THE OPPOSING WALL.

NOTE: CAROUSEL TRAYS SUPPLIED AS A SINGLE ITEM, IT IS RECOMMENDED THAT YOU SUPPLY TWO CAROUSELS PER BASE CORNER UNIT. NOTE: CAROUSEL TRAYS WILL ONLY SUIT 1000MM BASE CORNER UNITS, WITH A DOOR SIZE OF 500MM.

BASE DISPLAY PENINSULAR BACK PANELS

[[[

NOTE: PENINSULAR BACK PANELS SHOULD BE SPECIFIED EITHER 751MM OR 934MM HIGH TO SUIT ADJACENT UNITS. REMEMBER TO SPECIFY HEIGHT, LENGTH AND GRAIN DIRECTION WHEN ORDERING. NOTE: WHEN USED IN CONJUNCTION WITH BASE DISPLAY PENINSULAR UNITS, A BACK PANEL FIXING KIT 6012 MUST BE SPECIFIED (SEE BELOW).

BASE DISPLAY PENINSULAR BACK PANEL FIXING KIT

CODE 6012

ALUMINIUM TRIM

ALUMINIUM TRIM

PENINSULAR

PENINSULAR

PENINSULAR

PENINSULAR

PANEL

PANEL

PANEL

PANEL

934mm HIGH

898mm HIGH

751mm HIGH

715mm HIGH

6012 PLINTH

6012 PLINTH

NOTE: TO BE SPECIFIED IN CONJUNCTION WITH A BASE PENINSULAR BACK PANEL (SEE ABOVE).

BASE FLY END PANELS Without notch

6

MANHATTAN SPECIFIER’S GUIDE

NEW HEIGHT 934mm

WIDTH

DEPTH

CODE

16

591 668

6328 6329


BASE DRAWER UNITS WITH ‘METAL-SIDED’ THREE-QUARTER OPENING DRAWERS

WIDTH

568 DEEP

Three drawer unit - comprising two top drawer and one high-sided drawer

500 600

2137 2138

BASE DRAWER UNITS WITH TWIN-WALLED, FULL EXTENSION, SOFT CLOSING DRAWERS

WIDTH

568 DEEP

Three drawer unit

800 1000

2139 2140

450mm deep drawer box, finished in white 2 X Drawer front, height 140mm 1 X Deep drawer fronts, height 355mm

450mm deep drawer box, finished in grey 2 X Drawer front, height 140mm 1 X Pan drawer fronts, height 355mm

SOFT CLOSING DOORS - UPGRADE OPTION

CODE

Available with to suit all base, wall, highboard and tall units as an optional upgrade

HINGE064A

NOTE: THE CODE HING064A = ALL THE DOORS IN ONE KITCHEN, MARK THE QUANTITY OF DOORS IN THE KITCHEN NEXT TO THE CODE HING064A NOTE: NOT SUITABLE FOR BI-FOLD WALL UNITS

DRAWER UNITS WITH TWIN-WALLED, FULL EXTENSION, SOFT CLOSING DRAWERS - UPGRADE OPTION

CODE

Available as up upgrade option to all base and tall units

MECH126A

NOTE: THE CODE MECH126A = ALL THE DOORS IN ONE KITCHEN, MARK THE QUANTITY OF DOORS IN THE KITCHEN NEXT TO THE CODE MECH126A NOTE: NOT SUITABLE FOR BI-FOLD WALL UNITS RAWER

DRAWERS - UPGRADE OPTION

UNITS WITH TWIN-WALLED, FULL EXTENSION, SOFT CLOSING

ENTRY LEVEL DRAWER UNITS WITH SINGLE-WALLED, SOFT CLOSING DRAWERS - UPGRADE OPTION

CODE

Available as up upgrade option to all base and tall units

SDRAWER10

NOTE: THE CODE MECH000A = ALL THE DRAWERS IN ONE KITCHEN, MARK THE QUANTITY OF DRAWERS IN THE KITCHEN NEXT TO THE CODE MECH000A

BASE OVEN HOUSING UNITS

WIDTH

568 DEEP

600

2141

HEIGHT

WIDTH

CODE

720

70

6019

To suit an integrated oven Aperture height 600mm Two infill panels height = 58mm each

NOTE: TOP RAIL TO BE REMOVED ON SITE.

BASE UNIT INTEGRATED APPLIANCE CONVERSION KIT

NOTE: USED TO CONVERT A FREE-STANDING APPLIANCE SPACE OF 620MM TO AN INTEGRATED SPACE OF 600MM. NOTE: STANDARD ‘S’ FRAME FRONT STRIP OF 50MM IS REPLACED WITH THIS SPECIAL FRONT STRIP OF 70MM ON SITE.

MANHATTAN SPECIFIER’S GUIDE

7


BASE UNIT INFILL PANELS New Panel height 715mm

WIDTH

715 HIGH

150 300 400

8001 8002 8003

WIDTH

568 DEEP

300

6001

SIZE

CODE

ALUMINIUM TRIM

PLEASE NOTE: THE INFILL TO BE POSITIONED FLUSH WITH FRONT FACE OF THE ADJACENT DOOR, THIS MODIFICATION IS TO ALLOW FOR THE ALUMINIUM TRIM TO RUN BEHIND THE INFILL PANEL.

NOTE: TO BE ASSEMBLED AND CUT DOWN ON-SITE TO SUIT THE REQUIRED WIDTH. NOTE: MINIMUM WIDTH IS 16MM.

BASE TRAY SPACE

NOTE: SUPPLIED 300MM WIDE, TO BE CUT DOWN ON-SITE TO REQUIRED WIDTH. NOTE: MINIMUM WIDTH IS 100MM.

WORKTOP ALUMINIUM TRIM & FIXING KIT

WORKTOP TRIM THE QUANTITY AND LENGTH MUST BE SPECIFIED THE PRICE FOR THE ALUMINIUM TRIM = PRICE PER LINEAR METER THE MAX LENGTH OF THE TRIM = 3M

TRIM 56mm High ONE PAIR OF FIXING CLIPS

6362 FITT 111A

FIXING CLIPS THE QUANTITY OF FIXING CLIPS MUST BE SPECIFIED ALLOW ONE PAIR OF FIXING CLIPS PER UNIT FIXING DETAILS FOR THE ALUMINIUM FINGER TRIM ‘A’ POSITION THE BLACK PLASTIC TRIM HOUSING INTO THE END CUT OUT OF ALL FOUR END PANELS. ‘B’ POSITION AND SLIDE THE FOUR SMALL BLACK PLASTIC TRIM RUNNERS ONTO THE ALUMINIUM TRIM. ‘C’ PUSH/HAMMER THE FOUR SMALL TRIM RUNNERS ONTO THE TRIM HOUSING, WHEN THE FITTING ARE LOCATED TOGETHER SCREW THE TRIM HOUSINGS TO THE END PANELS

DETAIL SHOWING THE ALUMINIUM TRIM AND PLASTIC FIXINGS

8

MANHATTAN SPECIFIER’S GUIDE

DETAIL ’A’

DETAIL ’B’

DETAIL ’C’


EXTRA DEEP BASE UNIT END PANELS - TO SUIT UNITS USING 650mm DEEP WORKTOPS

CODE Lt & Rt Hd 6337

How to order the extra deep end panels: 1: Order the base or tall unit that needs an extra deep end as a standard unit code. Then add SJC A5666 so the extra deep end can be added to the correct unit on the order 2: Order the extra deep end panel to suit that unit, using the new codes. Then add SJC A5666 so the extra deep end can be added to the order.

The base unit will be fitted with Two extra deep end panels per unit

3: The extra deep end panel will then be fitted to the required unit in the factory

EXTRA DEEP TALL UNIT END PANELS - TO SUIT UNITS USING 650mm DEEP WORKTOPS

2120mm

2300mm

CODE

1970 2300

6335 6336

WIDTH

2120 HIGH

2300 HIGH

300

Lt Hd 3451 Rt Hd 3452 Lt Hd 3453 Rt Hd 3454 Lt Hd 3455 Rt Hd 3456 Lt Hd 3457 Rt Hd 3458

Lt Hd 3459 Rt Hd 3460 Lt Hd 3461 Rt Hd 3462 Lt Hd 3463 Rt Hd 3464 Lt Hd 3465 Rt Hd 3466

The tall unit will be fitted with Two extra deep end panels per unit

TALL LARDER UNITS

Unit height 2120mm Carcase height 1970mm Top door height 1245mm Bottom door height 715mm One fixed shelf Two loose shelves For more shelves please see page 16

2120 high

HEIGHT

Unit height 2300mm Carcase height 2150mm Top door height 1245mm Bottom door height 895mm One fixed shelf Two loose shelves For more shelves please see page 16

400 500 600

2300 high

NOTE: LARDERS & BROOM UNITS MUST BE SPECIFIED WITH VERTICAL ALUMINIUM STRIP TO ALLOW ACCESS THE THE DOOR HANDLES PLEASE SEE PAGE 11 FOR DETAILS TALL UNIT INFILL PANELS

WIDTH

2120 HIGH

2300 HIGH

150 300 400

8032 8016 8092

8031 8014 8093

WIDTH

CODE

300 400 500 600

6027 6024 6028 6029

NOTE: TO BE ASSEMBLED AND CUT DOWN ON-SITE TO SUIT THE REQUIRED WIDTH. NOTE: MINIMUM WIDTH IS 16MM. NOTE: 1970MM HIGH INFILL PANEL TO BE USED WITH 2120MM HIGH TALL UNITS. NOTE: 2150MM HIGH INFILL PANEL TO BE USED WITH 2300MM HIGH TALL UNITS.

TALL UNIT SHELVES

NOTE: SHELVES MANUFACTURED FROM 16MM MELAMINE FACED CHIPBOARD, LIPPED WITH 0.6MM PVC EDGING. COLOUR DECIDED BY RANGE CHOICES. NOTE: SUPPLIED AS A PAIR WITH SHELF CLIPS. NOTE: SHELF WIDTH ANNOTATED IS NOMINAL TO SUIT UNITS.

MANHATTAN SPECIFIER’S GUIDE

9


SPECIFICATION OF APPLIANCES TO SUIT A HOUSING UNIT Manhattan can supply both highboard and tall housing units to accommodate a wide selection of built in ovens, refrigerators, freezers, microwaves and combinations. The appliance manufacturer and model must be specified when ordering to enable us to prepare exact sizes and if necessary, detail special units to suit individual requirements. Where the appliance height is less than the aperture size, an infill panel is fitted. All appliances must be fitted strictly in accordance with the manufacturer’s instructions. Please check the manufacturer’s appliance instructions with regard to specific ventilation requirements: it may be necessary to notch the plinth locally. TALL HOUSING UNITS with UPGRADED TOP DOOR STAY

DEPTH

WIDTH

2120 HIGH

2300 HIGH

To suit a single oven

568

600

Lt Hd 4601 Rt Hd 4602

Lt Hd 4607 Rt Hd 4608

568

600

4603

4611

568

600

4600

Lt Hd 4609 Rt Hd 4610

568

600

4604

4612

2120 high

Unit height 2120mm Carcase height 1970mm Top door height 450mm Top Infill panel to suit Bottom Infill panel 40mm Bottom door height 715mm

Unit height 2300mm Carcase height 2150mm Top door height 715mm Top Infill panel to suit Bottom Infill panel 40mm Bottom door height 715mm

To suit a single oven at 595mm high

To suit a single oven at 595mm high

2300 high

NOTE: TO ALLOW FOR THE TOP DOOR TO OPEN THE UNIT WILL BE FITTED WITH PUSH FIT HINGES AND CATCHES.

To suit a single oven and microwave

2120high

2300 high

Unit height 2120mm Carcase height 1970mm Top door height 283mm Top Infill panel to suit Bottom Infill panel 40mm Drawer height 140mm Pan drawer height 355m

Unit height 2300mm Carcase height 2150mm Top door height 450mm Top Infill panel to suit Bottom Infill panel 40mm Drawer height 140mm Pan drawer height 355m

To suit a single oven at 595mm high & microwave from 382mm to 454mm

To suit a single oven at 595mm high & microwave from 382mm to 454mm

NOTE: TO ALLOW FOR THE TOP DOOR TO OPEN THE UNIT WILL BE FITTED WITH PUSH FIT HINGES AND CATCHES.

To suit a oven

2120 high

Unit height 2120mm Carcase height 1970mm Top door height 355mm Top Infill panel to suit Bottom Infill panel 40mm Drawer height 140mm Pan drawer height 355m

Unit height 2300mm Carcase height 2150mm Top door height 570mm Top Infill panel to suit Bottom Infill panel 40mm Drawer height 140mm Pan drawer height 355m

To suit a double oven at 888mm high

To suit a double oven at 888mm high

2300 high

NOTE: TO ALLOW FOR THE TOP DOOR TO OPEN THE UNIT WILL BE FITTED WITH PUSH FIT HINGES AND CATCHES.

To suit a double oven and microwave

Unit height 2120mm Carcase height 1970mm Top infill panel to suit Bottom Infill panel 40mm Pan drawer height 355m To suit a double oven at 888mm high & microwave from 382mm to 454mm 2120 high

Unit height 2300mm Carcase height 2150mm Top door height 283mm Top Infill panel to suit Bottom Infill panel 40mm Pan drawer height 355m To suit a double oven at 888mm high & microwave from 382mm to 454mm

2300 high

NOTE: TO ALLOW FOR THE TOP DOOR TO OPEN THE UNIT WILL BE FITTED WITH PUSH FIT HINGES AND CATCHES.

10

MANHATTAN SPECIFIER’S GUIDE


TALL HOUSING UNITS - CONTINUED

DEPTH

To suit a refrigerator and /or freezer

568

2120 high

Unit height 2120mm Carcase height 1970mm Top door height 1245mm Bottom door height 715mm

Unit height 2300mm Carcase height 2150mm Top door height 1245mm Bottom door height 895mm

Aperture 1937mm

Aperture 2117mm

WIDTH 2300 HIGH 600

2120 HIGH Lt Hd 4605 Rt Hd 4606

2300 HIGH Lt Hd 4629 Rt Hd 4630

2300 high

TALL UNIT FRIDGE- FREEZERS MUST BE SPECIFIED WITH VERTICAL ALUMINIUM STRIP, PLEASE SEE DETAIL BELOW VERTICAL SPACING BATTENS & ALUMINIUM TRIM FOR JOINTING LARDER, BROOM & FRIDGE FREEZERS TALL UNITS

BATTEN

NOTE: THE BATTEN IS INCLUDED IN THE CODE FOR THE ALUMINIUM TRIMS

WIDTH

1970 HIGH

64 ALUMINIUM 6360 48 ALUMINIUM 6363

2150HIGH 6361 6364

64MM WIDE ALUMINIUM TRIM, PLEASE SEE DETAIL BELOW

BATTEN

48MM WIDE ALUMINIUM TRIM FOR FITTING AT THE END OF A RUN OF TALL UNITS WITH ADJACENT DECOR PANEL, PLEASE SEE DETAIL BELOW

1: VERTICAL SPACING BATTEN MADE IN TWO PARTS FROM 16mm ALUMINIUM GREY MFC WITH 0.4 MATCHING PVC EDGING TO THE FRONT EDGES. 2: THE BATTENS ARE MADE IN ONE LENGTH TO SUIT THE 2150mm HIGH TALL UNIT. THE BATTEN IS THEN REDUCED IN HEIGHT TO SUIT THE 1970mm HIGH TALL UNIT BY THE FITTER ON SITE. 3: THE TWO PART TO BE SCREWED TOGETHER ON SITE BY THE FITTER AND FITTED FLUSH WITH THE FRONT EDGES OF THE TALL UNIT END PANEL.. 4: THE ALUMINIUM TRIM TO BE FIXED TO THE FRONT EDGES OF THE TALL UNIT AND THE JOINTING BATTENS WITH DOUBLE SIDED TAPE. 5: WHEN DESIGNING THE KITCHEN WITH TALL UNIT ALLOW 32mm BETWEEN TALL UNITS FOR THE VERTICAL BATTENS, NOTE: THE ALUMINIUM FRONT STRIPS ARE DESIGNED TO COVER THE FRONT EDGES OF THE BATTENS AND ADJACENT TALL UNIT END PANELS . DETAIL SHOWING HOW THE LARDER, BROOM & FRIDGE FREEZERS WILL BE JOINTED TOGETHER

DETAIL SHOWING TALL FRIDGE / BROOM UNITS WITH THE 64mm VERTICAL ALUMINIUM TRIM & 32mm SPACING BATTENS FITTED

DETAIL SHOWING TALL FRIDGE - FREEZER UNIT NEXT TO A TALL OVEN HOUSING UNIT WITH THE 48mm VERTICAL ALUMINIUM TRIM & 32mm SPACING BATTEN

Detail showing the recessed handle for the Fridge Freezer & Broom units

DETAIL SHOWING END OF RUN TALL FRIDGE / BROOM UNIT WITH THE 48mm VERTICAL ALUMINIUM TRIM & 32mm SPACING BATTEN

MANHATTAN SPECIFIER’S GUIDE

11


ALL WALL UNITS ARE HANDLE-LESS

Detail showing the side view of the wall unit

Detail showing the optional bottom panel with lighting hole and channel, this will

Note: the double bottom panels this is to allow a finger space to open the door.

allow for one down lighter per unit, hole size for the light = 58mm dia.

RECESS SPOTLIGHTS & TRANSFORMERS ARE NOT PART OF THE UNIT CODE AND WILL NEED TO BE SPECIFIED : CODE FOR THE LED RECESS SPOTLIGHT ACCS180A CODE FOR THE LED DRIVER / TRANSFORMER ACCS181A WITH 1.8 OF MAINS LEAD NOTE: MAXIMUM 4 SPOTLIGHT PER LED DRIVER / TRANSFORMER WALL UNITS with UPGRADE TOP DOOR STAY

WIDTH

360 HIGH

BOTTOM WITHOUT LIGHT RECESS

With full-height, lift-up door

500 600 800 1000

1404 1405 1406 1407

WIDTH

575 HIGH

360 HIGH BOTTOM WITH LIGHT RECESS

1604 1605 1606 1607

NOTE: ON 800MM AND 1000MM WIDE UNITS SOME RANGES MAY HAVE TWO DOORS ATTACHED TO EACH OTHER SIDE BY SIDE. NOTE: ON 800MM AND 1000MM WIDE UNITS THERE WILL BE AN INTERNAL SUPPORT RAIL BETWEEN THE TOP AND BOTTOM OF THE UNIT.WALL

UNITS

WALL UNITS 575mm HIGH With full-height door

BOTTOM WITHOUT LIGHT RECESS

300 400 450 500 575 high

575 high

600 800 900 1000

WALL UNITS

WIDTH

720 HIGH

BOTTOM WITHOUT LIGHT RECESS

With full-height door

300

800 900 1000

Lt Hd 1423 Rt Hd 1424 Lt Hd 1425 Rt Hd 1426 Lt Hd 1427 Rt Hd 1428 Lt Hd 1429 Rt Hd 1430 Lt Hd 1431 Rt Hd 1432 1433 1434 1435

WIDTH

720 HIGH

400 450 500 720 high

720 high

900 high

600

Lt Hd 1623 Rt Hd 1624 Lt Hd 1625 Rt Hd 1626 Lt Hd 1627 Rt Hd 1628 Lt Hd 1629 Rt Hd 1630 Lt Hd 1631 Rt Hd 1632 1633 1634 1635

900HIGH BOTTOM WITHOUT LIGHT RECESS

Lt Hd 1443 Rt Hd 1444 Lt Hd 1445 Rt Hd 1446 N/A N/A Lt Hd 1449 Rt Hd 1450 Lt Hd 1451 Rt Hd 1452 1453 N/A 1455

Lt Hd 1609 Rt Hd 1610 Lt Hd 1611 Rt Hd 1612 Lt Hd 1613 Rt Hd 1614 Lt Hd 1615 Rt Hd 1616 Lt Hd 1617 Rt Hd 1618 1619 1620 1621 900HIGH BOTTOM WITH LIGHT RECESS

Lt Hd1643 Rt Hd1644 Lt Hd1645 Rt Hd1646 N/A N/A Lt Hd 1649 Rt Hd 1650 Lt Hd 1651 Rt Hd 1652 1653 N/A 1655

900 high

WALL UNITS - DUAL HANDED

BOTTOM WITHOUT LIGHT RECESS

With full-height, dual-handed doors

800 900 1000

NOTE: IDEALLY USED ADJACENT TO A COOKER HOOD TO PREVENT DOOR CLASHES, OR INTO A CORNER ALSO TO PREVENT DOOR CLASHES.

12

720 HIGH BOTTOM WITH LIGHT RECESS

Lt Hd 1409 Rt Hd 1410 Lt Hd 1411 Rt Hd 1412 Lt Hd 1413 Rt Hd 1414 Lt Hd 1415 Rt Hd 1416 Lt Hd 1417 Rt Hd 1418 1419 1420 1421

575 HIGH BOTTOM WITH LIGHT RECESS

MANHATTAN SPECIFIER’S GUIDE

Lt Hd 1437 Rt Hd 1438 Lt Hd 1439 Rt Hd 1440 Lt Hd 1441 Rt Hd 1442

720 HIGH BOTTOM WITH LIGHT RECESS

Lt Hd 1637 Rt Hd 1638 Lt Hd 1639 Rt Hd 1640 Lt Hd 1641 Rt Hd 1642

900 HIGH BOTTOM WITHOUT LIGHT RECESS

Lt Hd 1457 Rt Hd 1458 N/A N/A Lt Hd 1461 Rt Hd 1462

900 HIGH BOTTOM WITH LIGHT RECESS

Lt Hd1657 Rt Hd1658 N/A N/A Lt Hd 1661 Rt Hd 1662


WALL BOILER HOUSING UNITS

DEPTH

WIDTH

720 HIGH

900 HIGH

With full-height door

316

500

Lt Hd 8795 Rt Hd 8796 Lt Hd 8797 Rt Hd 8798

Lt Hd 8895 Rt Hd 8896 Lt Hd 8897 Rt Hd 8898

Lt Hd 8765 Rt Hd 8766 Lt Hd 8761 Rt Hd 8762

Lt Hd 8965 Rt Hd 8966 Lt Hd 8961 Rt Hd 8962

600

With full-height door

420

500 600

WALL MICROWAVE HOUSING UNIT with UPGRADED TOP DOOR STAY

WIDTH

720 HIGH

900 HIGH

To suit 316mm deep wall units

500 600

1463 1464

1465 1466

WIDTH

450 HIGH

600

CH700

WIDTH 600

175 HIGH 8168

720 high

900 high

NOTE: THE MICROWAVE MANUFACTURER AND MODEL NUMBER MUST BE SPECIFIED SO THAT THE INFILL CAN BE MANUFACTURED TO SUIT. NOTE: TO ALLOW FOR THE DOOR TO OPEN THE UNIT WILL BE FITTED WITH PUSH FIT HINGES AND CATCHES. NOTE: LIGHTING FOR THESE UNITS IS NOT AVAILABLE

INTEGRATED EXTRACTOR HOOD

NOTE: 450MM HIGH TO SUIT 720MM WALL UNITS. NOTE: WHEN USING 900MM WALL UNITS, AN INTEGRATED EXTRACTOR HOOD INFILL PANEL MUST BE SPECIFIED (SEE BELOW).

INTEGRATED EXTRACTOR HOOD INFILL PANEL

NOTE: 175MM INFILL TO BE USED IN CONJUNCTION WITH INTEGRATED EXTRACTOR HOOD TO SUIT 900MM WALL UNITS.

TELESCOPIC COOKER HOOD

WIDTH 600 900

600 wide

900 wide

600 wide

900 wide

575 HIGH Lt Hd 1467 Rt Hd 1468 1471

720 HIGH Lt Hd 1469 Rt Hd 1470 1472

900 HIGH N/A N/A N/A

NOTE: THE HEIGHT OF THE TELESCOPIC HOOD WILL BE CALCULATED TO ALLOW FOR THE BOTTOM EDGE OF THE HOODS PULL-OUT TRIM TO FINISH FLUSH WITH THE THE BOTTOM EDGE OF THE ADJACENT WALL UNITS.

NOTE: TO ALLOW FOR THE DOOR TO OPEN THE UNIT WILL BE FITTED WITH PUSH FIT HINGES AND CATCHES. NOTE: THESE COOKER HOODS CAN NOT BE USED WITH GAS HOBS AS IT WILL BREACH CORGI REGULATIONS AND BS6172. ELECTRIC, CERAMIC AND INDUCTION HOBS ARE FINE. NOTE: INTERNAL WALL UNIT SHELVING IS REDUCED DEPTH TO ALLOW FOR EXTRACTOR MECHANISM; BEST SUITED FOR USE WITH SMALL SPICE JARS, ETC.

MANHATTAN SPECIFIER’S GUIDE

13


WALL CORNER UNIT 575mm HIGH

DOOR WIDTH

WIDTH

575 HIGH BOTTOM WITHOUT LIGHT RECESS

With full-height door - 600mm carcase width

300 (min 36-78)

600

575 HIGH BOTTOM WITH LIGHT RECESS

Lt Hd 1473 Rt Hd 1474

Lt Hd 1673 Rt Hd 1674

UNITS 575 high

WALL CORNER UNITS

DOOR WIDTH

720 HIGH

900 HIGH

BOTTOM WITHOUT LIGHT RECESS

720 HIGH

BOTTOM WITHOUT LIGHT RECESS

900 HIGH

BOTTOM WITH LIGHT RECESS

BOTTOM WITH LIGHT RECESS

With full-height door - 600mm carcase width

300 (min 36-78)

Lt Hd 1475 Rt Hd 1476

Lt Hd 1489 Rt Hd 1490

Lt Hd 1675 Rt Hd 1676

Lt Hd 1689 Rt Hd 1690

With full-height door - 600mm carcase width

400 (min 136-178) 450 (min 186-228) 500 (min 236-278)

Lt Hd 1477 Rt Hd 1478 Lt Hd 1479 Rt Hd 1480 Lt Hd 1481 Rt Hd 1482

Lt Hd 1491 Rt Hd 1492 N/A N/A Lt Hd 1493 Rt Hd 1494

Lt Hd 1677 Rt Hd 1678 Lt Hd 1679 Rt Hd 1680 Lt Hd 1681 Rt Hd 1682

Lt Hd 1691 Rt Hd 1692 N/A N/A Lt Hd1693 Rt Hd1694

500 (min 36-78) 600 (min 136-178)

Lt Hd 1483 Rt Hd 1484 Lt Hd 1485 Rt Hd 1486

Lt Hd 1495 Rt Hd 1496 Lt Hd 1497 Rt Hd 1498

Rt Hd 1683 Rt Hd 1684 Rt Hd 1685 Rt Hd 1686

Lt Hd 1695 Rt Hd 1696 Lt Hd 1697 Rt Hd 1698

600 (min 36-78)

Lt Hd 1487 Rt Hd 1488

Lt Hd 1499 Rt Hd 1500

Lt Hd 1687 Rt Hd 1688

Lt Hd 1699 Rt Hd 1700

720 high 900 high With full-height door - 800mm carcase width

720 high 900 high With full-height door - 900mm carcase width

720 high

900 high

HORIZONTAL OPENING DUAL HANDED WALL UNITS

WIDTH

720 HIGH BOTTOM WITHOUT LIGHT RECESS

500 600 800 1000

NOTE: TO ALLOW FOR THE TOP DOOR TO OPEN THE UNIT WILL BE FITTED WITH PUSH FIT HINGES AND CATCHES.

14

MANHATTAN SPECIFIER’S GUIDE

1501 1502 1503 1504

720 HIGH BOTTOM WITH LIGHT RECESS

1701 1702 1703 1704


WALL CORNER POST

WIDTH

720 HIGH

900 HIGH

636 X 636

6018

6023

WIDTH

720 HIGH

900 HIGH

150 300 400

8754 8753 8096

8930 8931 8097

WIDTH DEPTH 316

720 HIGH WIDTH 1200 1600 2000 2400

900 HIGH CODE 6312 6316 6320 6324

WALL UNIT GLASS SHELVES

WIDTH

CODE

To suit 316mm deep wall units - Optional extra

400 500 600 800 900 1000

GLAS070B GLAS071A GLAS072A GLAS073A GLAS069A GLAS074A

NOTE: A CORNER POST IS FITTED BETWEEN TWO ADJACENT UNITS WHERE A VOID SPACE IS CREATED IN THE CORNER.

WALL UNIT INFILL PANELS

NOTE: TO BE ASSEMBLED AND CUT DOWN ON-SITE TO REQUIRED WIDTH. NOTE: MINIMUM WIDTH IS 16MM.

WINDOW SOFFITS Without pelmet

16mm soffit panel NOTE: SUPPLIED READY TO BE CUT TO SIZE ON-SITE.

NOTE: SUPPLIED WITH GLASS SHELF CLIPS. NOTE: SHELF WIDTH ANNOTATED IS NOMINAL TO SUIT UNITS. NOTE: 800 AND 1000MM WALL DISPLAY BI-FOLDING UNITS CANNOT BE UPGRADED TO HAVE INTERNAL GLASS SHELVING.

MANHATTAN SPECIFIER’S GUIDE

15


VERTICAL BASE UNIT DECOR PANEL (Available in all Price Groups) Decor panel style.

Decor Panels are Range Dependent;

HEIGHT

DEPTH

16mm PANEL

NEW 935

591 641

8215 8216

They are manufactured from either MFC panels, Foil Wrapped panels all with a PVC edge. NOTE: THE STYLE OF THE DECOR PANELS WILL DIFFER ACCORDING TO THE RANGE CHOICES. NOTE: PANEL DEPTH: D 591 NOTE: PANEL DEPTH: D 641 TO SUIT 650 DEEP WORKTOPS

VERTICAL BASE PENINSULAR UNIT DECOR PANEL (Available in all Price Groups)

Decor panel style.

HEIGHT

DEPTH

NEW 935

646

16mm PANEL 8218

Decor Panels are Range Dependent; They are manufactured from either MFC panels, Foil Wrapped panels all with a PVC edge.

NOTE: THE STYLE OF THE DECOR PANELS WILL DIFFER ACCORDING TO THE RANGE CHOICES. NOTE: PANEL DEPTH: D 646

VERTICAL TALL UNIT DECOR PANEL (Available in all Price Groups)

Decor panel style.

Decor Panels are Range Dependent; They are manufactured from either MFC panels, Foil Wrapped panels all with a PVC edge.

NOTE: FOR ‘16MM THICK’,

DECOR PANELS FOR 2120MM TALL UNITS ARE PROVIDED 2150MM HIGH, AND DECOR PANELS FOR 2300MM ARE PROVIDED 2330MM HIGH.

16

MANHATTAN SPECIFIER’S GUIDE

HEIGHT

DEPTH

16mm PANEL

FOR 2156mm TALL UNITS FOR 2336mm TALL UNITS

591 641 591 641

8017 8265 8067 8267


VERTICAL VARIABLE SIZE DECOR PANEL (Available in all Price Groups)

HEIGHT

16mm PANEL

VARIABLE

9021

Decor panel style. Decor Panels are Range Dependent; They are manufactured from either MFC panels, Foil Wrapped panels all with a PVC edge.

NOTE: MAXIMUM BOARD SIZE = 2300 X 1200MM, WITH THE GRAIN FOLLOWING THE LONGEST LENGTH. NOTE: LENGTH, HEIGHT AND GRAIN DIRECTION MUST BE SPECIFIED WHEN ORDERING.

HORIZONTAL VARIABLE SIZE FRAMING PANEL (Available in all Price Groups)

Decor panel style.

Decor Panels are Range Dependent;

DEPTH

LENGTH

16mm PANEL

VARIABLE 339 DEEP

VARIABLE

8066

They are manufactured from either MFC panels, Foil Wrapped panels all with a PVC edge.

NOTE: LENGTH, HEIGHT AND GRAIN DIRECTION MUST BE SPECIFIED WHEN ORDERING.

DECOR PANEL SELF-ADHESIVE COVER CAPS

Self-Adhesive PVC cover caps: For use when fitting Decor Panels to units, or to cover the cam in the Wall Unit bottom panel.

PROTECTION PACKS

CODE CODE PLAS267A PLAS265A PLAS270A PLAS269A PLAS266A PLAS262A PLAS268A PLAS261A

CODES

6900 PROTECTION PACK

6904 PROTECTION PACK

6902 PROTECTION PACK

6905 FIRE PROTECTION PACK

12 METERS OF BUBBLE WRAP 750 WIDE 12 METERS OF CORRUGATED CARDBOARD 2 POLY BAGS NOTE: IDEALLY TO BE FITTED EITHER SIDE F

COLOUR COLOUR WHITE VANILLA ALUMINIUM GREY OAK BEECH MAPLE NATURAL AIDA WALNUT FERRARA OAK

12 METERS OF BUBBLE WRAP 750 WIDE 20 LENGTHS OF PROPLEX / CORREX 600 X 1200 X 2mm 10 LENGTHS OF NOMAFOAM U-CHANNEL 2 POLY BAGS

12 METERS OF BUBBLE WRAP 750 WIDE 8 LENGTHS OF PROPLEX / CORREX 600 X 1200 X 2mm 2 POLY BAGS

2 ROLLS OF PROMESH = 1.5mm WIDE X 10m LONG

6901 PROTECTION PACK

12 METERS OF BUBBLE WRAP 750 WIDE 12 METERS OF CORRUGATED CARDBOARD 20 LENGTHS OF PROPLEX / CORREX 600 X 1200 X 2mm 10 LENGTHS OF NOMAFOAM U-CHANNEL 2 POLY BAGS

17 17

MANHATTAN SPECIFIER’S GUIDE

MANHATTAN SPECIFIER’S GUIDE

17


CORNICE STYLE, material and finish specific to individual range. Style, material and finish specific to individual range.

CODE 2.3 meters 6061

HALF SWING-OUT WIRE BASKETS For use in a base corner units 2663/64 2627/28 & 2189/90 only.

CODE MECH001A

NOTE: SUPPLIED AS A PAIR.

CONTINUOUS PLINTH - 150MM HIGH Colour specific to individual range, supplied in 2.5m lengths Optional extra, manufactured from MFC, supplied in 2.5m lengths Optional extra, manufactured from MFC,supplied in 2.5m lengths PLINTH SEALER

CODE Range specific 6094 Aluminium effect 6083 White High Gloss 6087 CODE

Transparent plastic extrusion which clips to the bottom edge of the plinth. The flexible lip then seals the gap between the floor and the plinth.

PLAS250A

BREAKFAST BAR LEGS - 895MM HIGH 895mm x 25mm diameter chrome plated steel tube with sockets.

BREAKFAST BAR LEGS - 870MM HIGH 870mm x 60mm diameter, adjustable height leg.

NOTE: SUPPLIED IN 3M LENGTHS, CUT ON SITE TO SUIT REQUIREMENTS.

PLINTH AND WORKTOP VENTILATION GRILLS To be fitted into a housing unit plinth or fitted into a worktop over a highboard housing unit. NOTE: * MANUFACTURED FROM PLASTIC. NOTE: ** MANUFACTURED FROM ALUMINIUM, AND THEN SPRAYED THE APPROPRIATE COLOUR.

CODE *White FACM060A **Silver FACM082B **Gold FACM083A **White FACM084A

8 mm THICK WORKTOP UPSTANDS

CODE

For positioning directly above the worktop The size 100mm high x 3000mm MAX long

9199

12V /1.25W LED RECESS SPOTLIGHT WITH 18 DIODES

CODE

EACH LED LIGHT SUPPLIED WITH 2M OF LEAD AND CONNECTOR

ACCS180A

240V / 6W LED SPOTLIGHT DRIVER / TRANSFORMER

CODE

EACH DRIVER / TRANSFORMER SUPPLIED WITH 1.8 OF BARE ENDED MAINS LEAD NOTE: MAXIMUM OF 4 LED LIGHTS PER DRIVER / TRANSFORMER

ACCS181A

18 18

MANHATTAN MANHATTAN SPECIFIER’S SPECIFIER’S GUIDE GUIDE

BREAKFAST BAR LEGS - 710MM HIGH 710mm x 60mm diameter, adjustable height leg.

STAINLESS STEEL PILASTERS Manufactured from 50 x 100mm tubing.

CODE

Chrome LEGS036A

CODE White LEGS032A S/Steel LEGS035A Oak LEGS031A

CODE White LEGS030A S/Steel LEGS034A Oak LEGS033A

CODE 870mm FACM232A 720mm FACM233A 900mm FACM234A


TIMBER BATTENS

CODE 50 x 50 x 2400mm timber batten for supporting 650mm deep of Granite worktops. 20 x 50 x 2400mm timber batten for supporting worktops over appliance spaces, soffit panels or infill panels.

50x50x2400 TIMB021A 20x50x2400 TIMB020A

SINGLE POSTFORMED WORKTOPS

38MM

38mm & 60mm Single postformed laminate worktop

Depth up to 600mm. 9086 Depth 601850mm. 9087

CABLE MANAGEMENT FOR LIGHTING - CABLE TIE

CODE

To be used in conjunction with Self Adhesive bases .

FITT090A

HINGE OPTION TWO

CODE 175 deg

NOTE: 3.6M MAXIMUM LENGTH

DOUBLE POSTFORMED WORKTOPS

38MM

HINGE OPTION THREE

CODE

Depth 670mm. 9088 Depth 900mm. 9089

NOTE: 3.6M MAXIMUM LENGTH

2MM ACRYLIC EDGED WORKTOPS 2mm Acrylic edged laminate worktop, acrylic edging available in: - Aluminium Wave - Beech multiplex - Beech/Steel multiplex - Walnut/Steel multiplex - Planked Cherry

CODE

107 deg

HINGE OPTION FOUR

CODE

Depth up to 850mm. 9120

107 deg Soft Close

NOTE: 3.6M MAXIMUM LENGTH

SQUARE EDGED WORKTOPS 38mm Square edged laminate worktop

CODE

HINGE OPTION SIX

CODE

Depth up to 850mm. 9061

175 deg Soft Close

NOTE: 3.0M MAXIMUM LENGTH

WORKTOP CONNECTOR BOLTS Each joint consists of a three butterfly bolts to be recessed into the worktop

CODE

SOFT CLOSING DOORS - UPGRADE OPTION Available with to suit

CODE

FACM009A

Available with to suit all base, wall, highboard and tall units as an optional upgrade

HING064A

NOTE: NOT SUITABLE FOR BI-FOLD WALL UNITS

CABLE MANAGEMENT FOR LIGHTING - SELF ADHESIVE BASE To be used in conjunction with cable ties .

CODE

SOFT CLOSING DRAWERS - UPGRADE OPTION DRAWER UNITS WITH TWIN-WALLED, FULL EXTENSION

CODE

Available as an upgrade option to all base and tall units

MECH126A

NOTE: THIS COMES AS STANDARD ON THE FULL EXTENSION DRAWERS

FITT091A ENTRY LEVEL DRAWER UNITS WITH SINGLE-WALLED, SOFT CLOSING DRAWERS - UPGRADE OPTION

CODE SDRAWER10

Available as an upgrade option to all base and tall units

MANHATTAN MANHATTAN SPECIFIER’S SPECIFIER’S GUIDE GUIDE

19 19


Product Selector for 2011

Linea Handle-less Kitchens Price Group

F Price Group

H

F16 DESCRIPTION

COLOURS CARCASE

Horizontal wood-grain effect MFC door with 2mm matching PVC edging Driftwood Aluminium Grey, Latte or White MFC

H11 DESCRIPTION

COLOURS CARCASE

Gloss ‘Slab-effect’ MFC door with 2mm matching PVC edging Gloss Aubergine Aluminium Grey, Latte or White MFC

H16 DESCRIPTION

COLOURS CARCASE

COLOURS CARCASE

Horizontal wood-grain effect MFC door with 2mm matching PVC edging Plum Wood Aluminium Grey, Latte or White MFC

H11 DESCRIPTION

COLOURS CARCASE

Gloss ‘Slab-effect’ MFC door with 2mm matching PVC edging Iridescent Gloss Anthracite Aluminium Grey, Latte or White MFC

H16 DESCRIPTION

COLOURS CARCASE

Gloss ‘Slab-effect’ design door with Glass effect PVC edging Gloss Red Aluminium Grey, Latte or White MFC

H19

DESCRIPTION

DESCRIPTION

CARCASE

Gloss Horizontal wood-grain effect MFC door, with matching edging Gloss Wenge Aluminium Grey, Latte or White MFC

M12 DESCRIPTION

COLOURS

M

DESCRIPTION

H19 COLOURS

Price Group

Gloss ‘Slab-effect’ design door with Glass effect PVC edging Gloss Magnolia Aluminium Grey, Latte or White MFC

F16

CARCASE

High gloss ‘Slab-effect’ design door High Gloss Black Aluminium Grey, Latte or White MFC

COLOURS CARCASE

Gloss Horizontal wood-grain effect MFC door, with matching edging Gloss Plum Aluminium Grey, Latte or White MFC

M12 DESCRIPTION

COLOURS CARCASE

High gloss ‘Slab-effect’ design door High-Gloss Latte Aluminium Grey, Latte or White MFC

F16 DESCRIPTION

COLOURS CARCASE

Horizontal wood-grain effect MFC door with 2mm matching PVC edging Ontario Walnut Aluminium Grey, Latte or White MFC

H11 DESCRIPTION

COLOURS CARCASE

Gloss ‘Slab-effect’ MFC door with 2mm matching PVC edging Gloss Mocha Aluminium Grey, Latte or White MFC

H16 DESCRIPTION

COLOURS CARCASE

Gloss ‘Slab-effect’ design door with Glass effect PVC edging Gloss White Aluminium Grey, Latte or White MFC

F07 DESCRIPTION

COLOURS CARCASE

Plain colour MFC door with 2mm matching PVC edging Lava Aluminium Grey, Latte or White MFC

H11 DESCRIPTION

COLOURS CARCASE

Gloss ‘Slab-effect’ MFC door with 2mm matching PVC edging Gloss Latte Aluminium Grey, Latte or White MFC

H18 DESCRIPTION

COLOURS CARCASE

Gloss Vertical wood -grain effect MFC door, with matching edging Gloss Olive Aluminium Grey, Latte or White MFC

H19 DESCRIPTION

COLOURS CARCASE

Gloss Horizontal wood-grain effect MFC door, with matching edging Gloss Silver Oak Aluminium Grey, Latte or White MFC

M12 DESCRIPTION

COLOURS CARCASE

High gloss ‘Slab-effect’ design door High-Gloss Ivory Aluminium Grey, Latte or White MFC

M12 DESCRIPTION

COLOURS CARCASE

High gloss ‘Slab-effect’ design door High-Gloss White Aluminium Grey, Latte or White MFC

H16 DESCRIPTION

COLOURS CARCASE

Gloss ‘Slab-effect’ design door with Glass effect PVC edging Gloss Black Aluminium Grey, Latte or White MFC

H19 DESCRIPTION

COLOURS CARCASE

Gloss Horizontal wood-grain effect MFC door, with matching edging Gloss Cordoba Aluminium Grey, Latte or White MFC


Linea Handless Range units