Page 1

Specification Sheet SS-2150-T

pressure

Model Type T

Hydraulic Deadweight Tester

Pressure Range 100 to 10,000 kPa (10 to 15,000 psi)

Accuracy to ±0.015% of Indicated reading Accuracy ±0.025 and 0.100% is also available

Repeatebility ±0.005% of Indicated reading

Available units psi, kg/cm2, bar, kPa

Flexible configurations to meet differing applications - single column for field use - dual column for lab use

Robust construction allows for repeated daily use Proven in design and application to meet your needs Complete tester with tools, cases, and fittings Traceable certification supplied with each tester

ISO 9001 Manufacturer

PRODUCT DESCRIPTION The M&G Type T Hydraulic Deadweight Tester offers laboratory accuracy in an instrument that is designed to withstand an industrial environment. These testers are designed to be primary pressure standards and are available in several ranges and engineering units Laboratory accuracy The M&G Type T Deadweight tester is available in ranges to 1,000 bar (15,000 psi). This robust tester has been engineered to withstand the stresses of daily operation in a manufacturing environment and still maintain its accuracy and repeatability. The Type T is constructed of 300 series stainless steel and Monel and is supplied with Buna N O-rings as a standard unit. Viton and EPT O-rings are optional. This deadweight can use a water/alcohol mix or hydraulic oils for the pressure medium.


Model T® Hydraulic Deadweight Tester

FEATURES Three accuracies available These instruments are available in ±0.100%, ±0.025%, and ±0.015% of reading. The accuracy stated is the overall accuracy of the tester. The accuracy takes into account linearity, hysteresis, and repeatability. It would also account for intrinsic corrections. Site corrections are the user’s responsibility and the unit will not perform as specified without them. The testers are manufactured to either International Standard Gravity of 9.80665 m/s2 or to a user specified local gravity.

Re-entrant piston / cylinders The Type T deadweight employs a re-entrant type piston/cylinder assembly. This design applies test fluid to the outside and inside of the cylinder. Unlike a simple piston/ cylinder, this configuration reduces clearance between the piston and cylinder as pressure increases. This reduces the rate of fluid leakage and increases float time, offers the technician more time for testing, and reduces the amount of pumping necessary to sustain the fluid loss.

Specification Sheet SS-2150-T

Configurations There are two important factors in the selection of the proper deadweight configuration for your application: ranges and location. If you have applications for a single range of tests, then a single piston/cylinder model is a good choice. However, if you have some high pressure and some low pressure testing, the Type T is available with dual piston/ cylinder assemblies that are interchangeable and operate using the same weight set (±0.100% and ±0.025% accuracies) or utilize dedicated weight sets for each piston/cylinder assembly (±0.015% accuracy). If you have the need to use the tester in a location other than a lab, you may need a smaller and more mobile configuration. The single column configuration will be your best selection. These are available with dual piston/cylinder assemblies. For the applications where the tester will be stationary, the dual column configuration is a good choice for those needing multiple ranges. These are supplied with two piston/cylinder assemblies and both columns are installed and ready for use. A selector valve is used to determine which column is in service at any given time.

Worldwide engineering units Re-entrant system

The M&G Type T deadweight tester can be manufactured in four different engineering units: psi, bar, kgt/cm2, and kPa. All of the different engineering units are available in any of the configurations.

Pressure media Because the Type T is manufactured using 300 series stainless steel and Monel, you can use either hydraulic fluids compatible with the material or a water/alcohol mixture. We also offer EPT and Viton® o-rings as options. This increases your media options. Additionally, we offer an isolation membrane to protect your piston/cylinder assemblies from abrasive media. This facilitates the use of other fluids as process media but allows for the benefits of MGAAA oil within the column, which preserves your calibrated parts.



www.ametekmg.com


Model T速 Hydraulic Deadweight Tester

Specification Sheet SS-2150-T

Overhung weight carriers Another feature of Type T deadweight tester is the way that the weights are positioned on the carrier. M&G utilizes an overhung weight carrier design. This design employs a tube carrier that is positioned over the column and onto the piston driver. The center of gravity for the stack of weights is lowered, reducing side thrust and friction; which lengthens the life of the piston/ cylinder assembly. This also improves measurement accuracy. Weight carrier

Deadweight piston & cylinder

Instrument under test

Venier

Pump

Test manifold

Weights

Check valves

Fluid reservoir

Protected piston/cylinder The piston and cylinder assembly are enclosed in the column of the tester. The weight carrier floats on the piston driver preventing damage to the piston/cylinder assembly. Additionally, the piston/cylinder assembly is engineered with positive over-pressure protection by restricting vertical movement. This protects the assembly from damage in the event of weight removal under pressure.

Dual volume pump The Type T pump offers a dual volume pumping feature that allows for large volume of fluid to be added at low pressures to fill the system and increase pressure rapidly. Once the system is filled, you can switch the output volume to a smaller volume. This eases pumping and also provides for finer control in higher pressure ranges. The reservoir is kept at atmospheric pressure meaning that you can also refill the tester during a calibration run.

Easy Leveling AMETEK floating ball testers incorporate a bulls-eye level for reference when preparing the unit for use. The tester also employs a 3-leg leveling system which is more convenient and is superior to a 4-leg system.

Small incremental weight sets Small incremental weight sets are avaliable to provide fractional output pressures. These are available for the Type T deadweight tester in psi, bar, kPa and kg/cm2.

www.ametekmg.com




Model T® Hydraulic Deadweight Tester

FUNCTIONAL SPECIFICATIONS

Specification Sheet SS-2150-T

Model:........................................................................ Type T

General Process Information for Calibrated Parts

Type:................................................ Hydraulic, piston gauge

Local gravity values must be specified by customer in gals, cm/sec sec, or m/sec sec.

Pressure range:.........................to 100,000 kPa / 15,000 psi ................................................................ (model dependent)

Include serial number, accuracy, gravity, and model number of deadweight tester when ordering weight sets or calibrated parts.

Masses for weights ordered separately, including tolerance, must be supplied by customer; unless combined with tester on same order.

Calibrated parts may be made to archival data if requested on the purchase order.

Calibrated parts are certified for physical dimension only (mass or area) and not for accuracy unless ordered with a new tester or the tester is returned for proper calibration of parts.

Weights for ±0.015% hydraulic testers cannot be purchased without the associated calibrated parts at AMETEK Calibration Instruments for calibration.

Accuracy (12 months):.................................to ±0.015% rdg Increments (low - min):.... 5 psi, 0.5 kg/cm2, 0.5 bar, 50 kPa Increments (high - min):.... 50 psi, 5 kg/cm2, 5 bar, 500 kPa Increments (small): Small incremental weight sets available Gravity:.......................9.80665 m/s2 (international standard) ....................Local gravity available (specify when ordering) Piston/cylinders:..........................Single or dual (as ordered) Columns:.....................................Single or dual (as ordered) Weight sets:................................Single or dual (as ordered) Pressure source:.....................Lever action, hand-actuated, .................................................dual volume hydraulic pump Medium:.....................Distilled water/alcohol mix (standard) ........................or AAA oil (optional) (specify when ordering) Reservoir capacity:...........................................1.23 l / 75 in3 Displacement (high range):................................................... .......................... 2.8 to 3.2 cm2 / 0.17 to 0.20 in3 per stroke

Certification of Accuracy and Traceability A Certification of Accuracy and Traceability to NIST is included with every AMETEK floating ball-type deadweight tester. An optional Certification of Accuracy with area, mass and intrinsic correction factors is available.

Displacement (low range):..................................................... .................. 0.30 to 0.40 cm2 / 0.018 to 0.024 in3 per stroke Wetted surfaces:............... 300 series stainless steel, monel O-rings:.......................... Buna N (standard), EPT (optional), ................................Viton (optional) (specify when ordering) Test connections: . ..............1/4” NPT, 1/2” NPT, 7/16 UNF .................... - 1/4” BSP and 1/2” BSP (with metric models) Weight material:.. Hard, non-magnetic alloy (imperial units), .......stainless steel ( ±0.015% imperial and metric models), ........................... aluminum (small incremental weight sets) Engineering units:................................ psi, kg/cm2, bar, kPa Cases:........... up to 4 (model and configuration dependent)

PHYSICAL SPECIFICATIONS Weight: Tester & Case:.............................................. 22.7 kg / 50 lbs Weight Sets:....................... 25 kg to 95.3 kg / 55 to 210 lbs Configuration:......................... Single or dual piston/cylinder ........................ single or dual column hydraulic deadweight Delivery:.......Pump, piston(s), weight set(s), tools, manifold, ........ adapters, column base, tubing (dual-column models), ..............................manual, and NIST traceable certification



www.ametekmg.com

Notes: For ±0.015% testers, ±0.025% accuracy below 30” H2O, 1 psi, 7 kPa, 100 cm H2O or 0.07 bar. Gravity 9.80665 cm/s2 or user’s local gravity when specified. H2O (water column) models are calibrated to water at 20°C (68°F) but can be calibrated to water at 60°F. Notes: Deadweight tester and deadweight gauge accuracy is expressed as “Percent of Indicated Pressure”. A 1.000 psi tester with an accuracy of ±0.01% of indicated pressure will have an allowable error of 0.1 psi at 10 psi, ±0.1 psi at 100 psi and ±1.0 psi at 1.000 psi. Generally, deadweight testers are used only in the upper 90% of the range.


Model T® Hydraulic Deadweight Tester

Specification Sheet SS-2150-T

ORDERING INFORMATION Single column / Single piston / cylinder units Model

Engineering units

Range area

Increments

Piston

T-5 T-10 T-15 T-20 T-30 T-55 T-110/TESTER T-155 TSQ-40M-1/C TSQ-70M-1/ C TSQ-100M-1/C TSQ-200M-1/C TSQ-400M-1/C TSQ-700M-1/C TSQ-100M-1/C TSQ-40B-1/C TSQ-70B-1/C TSQ-100B-1/C TSQ-200B-1/C TSQ-400B-1/C TSQ-700B-1/C TSQ-1000B-1/C TSQ-4000N-1/C TSQ-7000N-1/C TSQ-10000N-1/C TSQ-40000N-1/C TSQ-70000N-1/C TSQ-100000N-1/C

psi psi psi psi psi psi psi psi kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 bar bar bar bar bar bar bar kPa kPa kPa kPa kPa kPa

10 to 500 10 to 1,000 10 to 1,500 20 to 2,000 10 to 3,000 50 to 5,000 100 to 10,000 100 to 15,000 1 to 40 1 to 70 1 to 100 2 to 200 10 to 400 10 to 700 10 to 1,000 1 to 40 1 to 70 1 to 100 2 to 200 10 to 400 10 to 700 10 to1,000 100 to 4,000 100 to 7,000 100 to 10,000 1,000 to 40,000 1,000 to 70,000 1,000 to 100,000

5 5 5 10 10 25 50 50 0.5 0.5 0.5 1 5 5 5 0.5 0.5 0.5 1 5 5 5 50 50 50 500 500 500

0.10 0.10 0.10 0.20 0.20 0.50 0.01 0.01 0.10 0.10 0.10 0.20 0.01 0.01 0.01 0.10 0.10 0.10 0.20 0.01 0.01 0.01 0.10 0.10 0.10 0.01 0.01 0.01

in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2

Metric units are supplied with Complete Data Certifications as indicated by “/C’ Metric units are supplied with 0.025% of Reading Accuracy as indicated by “-1’

Single column / Dual piston / cylinder units Model

Engineering units

Range area

Increments

Piston

T-50 psi T-100 psi T-150/TESTER psi

10 to 500 100 to 5,000 10 to 1,000 100 to 10,000 10 to 1,500 100 to 15,000

5 50 5 50 5 50

0.10 0.01 0.10 0.01 0.10 0.01

in2 in2 in2 in2 in2 in2

www.ametekmg.com




Model T速 Hydraulic Deadweight Tester

Specification Sheet SS-2150-T

ORDERING INFORMATION - continued Single column / Dual piston / cylinder units Model

Engineering units

Range area

Increments

Piston

T-150 psi TQD-400M kg/cm2 TQD-700M kg/cm2 TQD-1000M kg/cm2 TQD-400B bar TQD-700B bar TQD-1000B bar TQD-40000N kPa TQD-70000N kPa TQD-100000N kPa

10 to 1,500 100 to 15,000 1 to 40 10 to 400 1 to 70 10 to 700 1 to 100 10 to 1,000 1 to 40 10 to 400 1 to 70 10 to 700 1 to 100 10 to 1,000 100 to 4,000 1,000 to 40,000 100 to 7,000 1,000 to 70,000 100 to 10,000 1,000 to 100,000

5 50 0.5 5 0.5 5 0.5 5 0.5 5 0.5 5 0.5 5 50 500 50 500 50 500

0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01

Engineering units

Range area

Increments

Piston

DM-T-50 psi DM-T-100 psi DM-T-150 psi DM-TQ-400M kg/cm2 DM-TQ-700M kg/cm2 DM-TQ-1000M kg/cm2 DM-TQ-400B bar DM-TQ-700B bar DM-TQ-1000B bar DM-TQ-40000N kPa DM-TQ-70000N kPa DM-TQ-100000N kPa

10 to 500 100 to 5,000 10 to 1,000 100 to 10,000 10 to 1,500 100 to 15,000 1 to 40 10 to 400 1 to 70 10 to 700 1 to 100 0. 10 to 1,000 1 to 40 10 to 400 1 to 70 10 to 700 1 to 100 10 to 1,000 100 to 4,000 1,000 to 40,000 100 to 7,000 1,000 to 70,000 100 to 10,000 1,000 to 100,000

5 50 5 50 5 50 0.5 5 0.5 5 5 5 0.5 5 0.5 5 0.5 5 50 500 50 500 50 500

0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01

in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2

Dual column / Dual piston / cylinder units Model



www.ametekmg.com

in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2


Model T® Hydraulic Deadweight Tester

Specification Sheet SS-2150-T

ORDERING INFORMATION - continued Special 0.015% Accuracy units Model

Engineering units

Range area

Increments

Piston

DM-T-150-1AL/C psi DM-TQ-400M kg/cm2 700M kg/cm2 1000M kg/cm2 400B bar 700B bar 1000B bar 40000N kPa 70000N kPa 100000N kPa

10 to 1,500 100 to 15,000 1 to 40 10 to 400 1 to 70 10 to 70 1 to 100 10 to 1,000 1 to 40 10 to 400 1 to 70 10 to 700 1 to 100 10 to 1,000 100 to 4,000 1,000 to 40,000 100 to 7,000 1,000 to 70,000 100 to 10,000 1,000 to 100,000

5 50 0.5 5 0.5 5 0.5 5 0.5 5 0.5 5 0.5 5 50 500 50 500 50 500

0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01 0.10 0.01

in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2 in2

These configurations are at Local Gravity (supplied on the Order) Units have one independent weight set for each piston/cylinder combination Other configurations are considered upon request

Options Accuracy: Gravity: Certification:

for 0.025% of Reading add “-1/C” to model number These units are all supplied with Data for 0.015% of Reading* add “-1AL/C” to model number 0.015% units are not considered standard and are subject to quotation of user specifications These units are all supplied with Data, Local gravity, and Special Weight Sets for Local Gravity add “L” to model number Gravity must be specified on order in gals. for Traceable Certification with Data add “/C” to model number

Examples T-50 with T-50 with T-50 with T-50 with

Local Gravity Certification with Data 0.025% Accuracy Local Gravity and 0.025% Accuracy

T-50/L T-50/C T-50-1/C T-50-1L/C

www.ametekmg.com




Accessories Order no.

Description

T-250 Pump rebuild kit - Type T Buna N (standard material) T-559 Pump rebuild kit - Type T VITON (optional material) T-326 Pump rebuild kit - Type T EPT (optional material) T-258 Piston/cylinder assembly kit - Type T Buna N (standard material) T-323 Piston/cylinder assembly kit - Type T VITON (optional material) T-576 Piston/cylinder assembly kit - Type T EPT (optional material) WG-109 Isolates media from piston/cylinder assembly - Buna N MGAAA/QT Tester oil - 0.95 l (1 qt) MGAAA/GL Tester oil - 3.79 l (1 gal) 99-90019 Oil dispenser T-134 Union body (15/16-20 UNEF male x 1/4” NPT female) T-135 Union body (15/16-20 UNEF male x 1/2” NPT female) T-186 Union body (15/16-20 UNEF male x 7/16” NPT female) T-331 Union body (15/16-20 UNEF male x 3/8” NPT female) T-863 Union body (15/16-20 UNEF male x 1/8” NPT female) T-786 Adapter (1/4” NPT male x 1/4” BSP female) T-787 Adapter (1/4” NPT male x 1/2” BSP female) 60I104 Roll of Teflon tape 101549 Bonded seal (1/2”) 60R120 Bonded seal (1/4”) 60R122 Bonded seal (1/8”) KH-18 Hose (0.46 m / 1.5 ft, 1/4” NPT male x 1/4” NPT male 700 bar / 10,000 psi Small incremental weight sets available in psi, bar, kPa and kg/cm2 Additional weight sets

AMETEK Calibration Instruments is one of the world’s leading manufacturers and developers of calibration instruments for temperature, pressure and process signals as well as for temperature sensors both from a commercial and a technological point of view. JOFRA Temperature Instruments Portable precision thermometers. Dry-block and liquid bath calibrators: 4 series, with more than 25 models and temperature ranges from -90° to 1205°C / -130° to 2200°F. All featuring speed, portability, accuracy and advanced documenting functions with JOFRACAL calibration software. JOFRA Pressure Instruments Convenient electronic systems ranging from -1 to 1000 bar (25 inHg to 14,500 psi) multiple choices of pressure ranges, pumps and accuracies, fully temperature-compensated for problem-free and accurate field use. JOFRA Signal Instruments Process signal measurement and simulation for easy control loop calibration and measurement tasks - from handheld field instruments to laboratory reference level bench top instruments. JOFRA / JF Marine Instruments A complete range of calibration equipment for temperature, pressure and signal, approved for marine use. FP Temperature Sensors A complete range of temperature sensors for industrial and marine use. M&G Pressure Testers Hydraulic floating-ball or hydraulic piston dead weight testers with accuracies to 0.015% of reading. M&G Pumps Pressure generators from small Hydraulic “bicycle” style pumps to hydraulic pumps generating up to 1,000 bar (15,000 psi).

...because calibration is a matter of confidence

www.ametekcalibration.com www.jofra.com Headquarter: AMETEK Denmark A/S Gydevang 32-34 • 3450 Allerød • Denmark Tel: +45 4816 8000 • ametek@ametek.dk Sales & Service: Europe, Asia, Africa, Middle East and South America

Information within this document is subject to change without notice. ©2007, by AMETEK, Inc., www.ametek.com. All rights reserved. Pub code SS-2150-T Issue 0710



www.jofra.com

Sales & Service Offices: AMETEK Mansfield & Green (North America) Tel: +1 800 527 9999 • cal.info@ametek.com AMETEK Singapore Pte. Ltd. (Singapore) Tel: +65 6 484 2388 • aspl@ametek.com.sg AMETEK Inc. Beijing Rep. Office (China) Tel: +86 10 8526 2111 • jofra@ametek.com.cn AMETEK GmbH (Germany) Tel: +49 2159 91360 • info@ametek.de AMETEK Lloyd Instruments (UK) Tel: +44 (0) 1489 486 404 • jofra@ametek.co.uk

Ametek Hydraulic Deadweight Tester  

Hydraulic Deadweight Tester

Read more
Read more
Similar to
Popular now
Just for you