Page 1

SGT HIGH SPEED IP RADIO

OUTDOOR IP Radio

802.11a/g/n Outdoor AP/CPE/Bridge The SGT-MN radios operate at 2.4/5GHz for distances up to 10km. The SGT-MN Series support all point-to-multipoint & point-to-point configurations.

Features

Rugged Outdoor Design Watertight housing: built-in lightning arrestor. The SGT-MN series are designed for the harshest outdoor environments.

Easy Installation A single Ethernet cable is required between the SGT-MN radio & LAN. There is a supplied outdoor mounting kit that allows a quick and simple installation.

There is a Buzzer that assists with the antenna panning

process. 

Mode Flexibility – PtMP AP, CPE, PtP Bridge Sagittar provides great flexibility for its IP products.

Based on the

customer’s requirements, the IP radios can be configured to work in the following modes: Bridge Mode-PtP, Access Point, CPE Mode 

Very intuitive Management & Maintenance interface


SGT HIGH SPEED IP RADIO

OUTDOOR IP Radio

Specifications Hardware Features

Additional Information

 IEEE802.3u 10/100 Fast Ethernet MDI(/IX)  IEEE802.11a WLAN interface  IEEE 802.11n Draft WLAN standard PoE 12W Power over Ethernet 12V Default Antenna 16dBi for 5GHz, 8dBi for 2.4GHz dual-polarity External Antenna SMA-type Connector (Plug) Connector -Switchable using software Antenna Conf. 2xT 2xR Ethernet Physical Interface 10/100, 2 Ports  Support for Web-based upgrade: Ethernet port or wireless network  Support for TFTP upgrade - Ethernet port System Update Options 12VDC @1.5A (switching). If there is a POE output, then POE input must be 15VDC. If there is no POE output, that means no other equipment is powered by the PoE Adapter Requirements MN radio; then a POE input of 12 VDC is used. Data Rates Draft 11n, MCS(0 to 7): HT20&40 11a: 54M/48M/36M/24M/18M/12M/9/6 Mbps auto adjust 11g: 54M/48M/36M/24M/18M/12M/9/6 Mbps auto adjust Data modulation OFDM 802.11a/g/n RF frequency range FCC :2.412-2.462MHz, 5725-5850 MHz Standards Compliance

CE: 2.412-2.472MHz, 5470-5725 MHz (DFS band), 5725-5850 (DFS band) Please note: Customization for 4.9-6.1GHz, thereby allowing radio operation in licensed bands is available UPON REQUEST.

Output Power & Sensitivity FCC @ 25C IEEE 802.11a 6-24Mbps 36Mbps 48Mbps 54Mbps IEEE 802.11n MCS0 MCS15

Tx Power 27dBm 25dBm 23dBm 22dBm

Sensitivity

27dBm 21dBm

-96dBm -75dBm

-94dBm -80dBm -77dBm -75dBm


SGT HIGH SPEED IP RADIO

OUTDOOR IP Radio

Firmware Functions

Details

Interface Language Status

System

English Information Statistics: Wireless and Ethernet Connection status Basic Settings: Device Name, Country/Domain, Time/NTP IP

Wireless

Radius Settings Wireless Settings

IP address (Manual and DHCP) Optionally: enabled/disabled Operation Modes: AP or CPE Date Rate Selection - MCS0…MCS7 : (Best, 1, 2, 5, 11, 6, 9, 12, 18, 24, 36, 48, 54 Mbps) Open System, Shared Key WEP (152/128/64-bits), 802.1X-only, WPA, WPA2, TKIP WPA-PSK, AES WPA2-PSK Deny or Allow Station List and Station Transmit Flow control (Support for 32 stations) WMM Modes (Enable/Disable WMM) Web Management, Telnet support (Password-protected). SNMP Management, FTP, TFTP/Web for firmware upgrades

Power Adapter Spec - Output12VDC, 1A Environmental Specifications Environment Specification Operating Temperature Storage Temperature Operating & Storage Humidity (non-condensing) RoHS Compliance Warranty

Description -20 ~+70C -30 ~+80C 5 to 95% R H RoHS Compliant 12 Months


SGT HIGH SPEED IP RADIO

OUTDOOR IP Radio

Field Test Results

5km Antenna Internal (16dBi) Internal (16dBi)

Reference Configuration Data rate Auto Bandwidth HT20 Data rate Auto Bandwidth HT40

Throughput

75Mbps 95Mbps

7km Antenna Internal (16dBi) Internal (16dBi)

Reference Configuration Data rate Auto Bandwidth HT20 Data rate Auto Bandwidth HT40

Throughput

45Mbps 70Mbps

10km Antenna Internal (16dBi) Internal (16dBi)

Reference Configuration Data rate Auto Bandwidth HT20 Auto Data rate HT40

Throughput

38Mbps 40Mbps


SGT HIGH SPEED IP RADIO

OUTDOOR IP Radio

Typical Application

Upon removing the bottom cover, as shown in the following photo, there are two “reverse SMA” connectors (for optional connection to an external antenna) and two RJ45 connectors.


SGT HIGH SPEED IP RADIO

OUTDOOR IP Radio

Although the radios have a built-in internal MIMO antenna, they are also designed for connection to an external antenna, which can be a Sector, Panel or Parabolic antenna. Use of external antennas allows use of higher gain, hence narrower antenna beamwidths which aid in the achievement of receive carrier level and C/I radio link engineering design goal objectives.

The radio is designed for direct connection to an IP camera. RJ45 connectors are shown.

In the photo below, two

The connection on the right (with a blue cable) is for PoE

supply and Ethernet connection to the radio. The connector on the left feeds DC power out and provides an Ethernet connection to an IP camera (thereby eliminating the need for additional Ethernet Switch equipment at the Radio/Camera location).

The above units are connected to 65 -3dB Beamwidth or 90 -3dB Beamwidth to create a multiple-sectored Base Station which aggregates traffic from multiple outlying CPE Radio terminals.

Depending on engineering design requirements, the remote CPE’s either use

their internal 35 V& H -3dB Beamwidth antennas or external panel or parabolic antenna.


SGT HIGH SPEED IP RADIO

OUTDOOR IP Radio

Mounting of a Radio Unit

The following photos show the connection method for the radios.

The mounting rings supports a pole diameter of 32mm to 70mm.

Sagittar MN IP Radio Series  

Sagittar MN IP Radio Series

Read more
Read more
Similar to
Popular now
Just for you