Page 1

Conventional Control Panels


CB200 1-8 Zone Conventional Control Panels

Key Features Built-in detector removal indication facility l

From 1 to 8 zones

l

4 Alarm circuits on 4-8 zone panels

l

Conforms to the requirements of EN54-2

l

User-friendly access code

l

One-man test facility

l

Non-latching zone feature

l

Class change input

l

Earth fault monitoring

l

Fully-functional repeater available (4 & 8 zone panels only)

l

Removable cable-entry grommets

l

User-friendly controls

l

Surface or semi-flush mounting as standard

l

Ample termination space

l

Flame-resistant polycarbonate enclosure

l

Log book and manual supplied

l

Complies with EMC and LVD directives

Introduction The CB200 conventional panel may be supplied in 1, 2, 4 or 8 zone formats. It complies with the requirements of EN54 Part 2. All zones and alarm circuits are monitored for open and short circuit fault conditions with detector removal facility also provided as standard. The cabinet will house 2 x 12V 2.1AH S.L.A. batteries wired in series, which will sustain an 8 zone panel for up to 24 hours. All panels have a zone 1 non-latch facility to enable panel interlinking without “lock-up� occurring. The class change input enables the alarm circuits to operate without panel indication or panel latching. The cabinet back-box houses only the transformer, thus providing a virtually empty enclosure for first fix installation. A steel gland plate, removable plastic grommets and ample space are designed to assist with cable termination. A slide-in insert is included for clear zone identification. The surface-mount electronics motherboard is fitted and terminated after first fix installation. Finally a terminal cover completes the panel installation.

Eurotech Fire Systems Limited www.eurotechfire.com | T +44 (0) 203 141 0999 | F +44 (0) 239 225 2554 | E info@eurotechfire.com


CB200 Specifications

Typical Connections

+

-

+

-

+

- 1A 2A +

- 1

+

2

+

DETECTOR BASE WITH SCHOTTKY DIODE

ALARMS 1, 2 & 3 SAME AS ALARM 4

CLASS CHANGE

-

+

ZONES 2-8 SAME AS ZONE 1

+

-

MANUAL CALL POINT WITH 680R RESISTOR

12V BATTERY

+

+

12V BATTERY

NORMALLY OPEN SWITCH

-

-

22uF CAPACITOR End-Of-Line Device

3K9 RESISTOR End-Of-Line Device

AUX FAULT N/O P N/C

AUX FIRE N/O P N/C

ALARM CIRCUITS AL4- AL4+ AL3- AL3+ AL2- AL2+ AL1- AL1+

ZONE 8 Z8- Z8+

ZONE 1 Z1- Z1+

REPEATER B A SCN

AUX 24V 0V

24V BAT- BAT+

SECONDARY EARTH AC IN .

~

~

.

LINK FOR BUZZER ENABLE

ON

1234

RA0 RA1 Z1NL NU

L E N 230V AC 50Hz 5A MAINS SUPPLY

230V AC TRANSFORMER

Technical Specifications 1 zone panel

2 zone panel

4 zone panel

Maximum field equipment load:

800mA

Auxiliary 24VDC output:

250mA

Mains failed current consumption:

35mA @24VDC

Maximum battery charger output:

40mA @24VDC

40mA @24VDC

8 zone panel

40mA @24VDC

500mA @27.5 VDC

Common fire output:

Volt-free contacts - 1A, 30V DC max.

Common fault output:

Volt-free contacts - 1A, 30V DC max.

Alarm circuit output:

2 at 250mA each @28VDC

4at 500mA each @28VDC

4at 500mA each @28VDC

4at 500mA each @28VDC

Battery size:

2 x 12V 2.1AH sealed lead acid

2 x 12V 2.1AH sealed lead acid

2 x 12V 2.1AH sealed lead acid

2 x 12V 2.1AH sealed lead acid

Cabinet Sizes (Back box only) Weight (excluding batteries):

245mmH x 287mmW x 66mmD (Excluding front cover) 2.3kg

2.3kg

2.3kg

2.3kg

Note: On the 4-8 zone panels the total current available for the field devices is 800mA at 24VDC. This current must be shared between the alarm and aux. supply.

Part No: 2500/383

1 zone control panel

2500/384

2 zone control panel

2500/385

4 zone control panel

2500/386

8 zone control panel

29


Excel 2-8 Zone Twin Wire Control Panel

Key features • ‘Activate Controls’ keyswitch • Twin Wire Alarm panels • 2, 4, 6 & 8 zones • Designed to EN54 pt. 2 & 4 • Fully programmable features for maximum flexibility • CE marked to EMC & LVD • Surface mount technology for increased reliability • Two wire repeaters • Keypad controls and programming • Comprehensive specification • All metal enclosure for durability • Integral event retrieval • Programming available with ‘windows’ based software

Excel. One of the most versatile panels of its type ever built. The Surveyor Excel-K offers a comprehensive specification, while remaining competitively priced and is designed to comply with the new EN54 Pt.2 & 4 requirements. Surface mount technology, together with a switch mode power supply, ensure the very latest techniques are used to increase reliability and performance. Twin Wire control panels enable sounders to be connected on the same pair of wires as the detectors and call points. Can save up to 40% in labour and materials, while presenting a neater installation. Two wire repeaters, detector removal and sounder walk tests are amongst the popular features of this panel.

Eurotech Fire Systems Limited www.eurotechfire.com | T +44 (0) 203 141 0999 | F +44 (0) 239 225 2554 | E info@eurotechfire.com


Excel 2-8 Zone Twin Wire Control Panel

Part No.

Sounder Circuits

Standby Current mA

Dimensions mm

Max Alarm Load

Battery Space

2

FCPXLK-2TW

4

91

460L x 310H x 85D

2A

7Ah x 2

4

FCPXLK-4TW

6

99

460L x 310H x 85D

2A

7Ah x 2

6

FCPXLK-6TW

8

107

460L x 310H x 85D

2A

7Ah x 2

8

FCPXLK-8TW

10

115

460L x 310H x 85D

2A

7Ah x 2

Detection Zones Twin-Wire

Main Features

Internal Controls – Level 3

Suitability ‘Twin Wire’

• ‘Activate Controls’ keyswitch • Twin Wire models • Suits many detectors (Conventional) • Integral detector removal monitoring (indicated zonally) • 3 amp switch mode power supply • Soft tactile keypad for controls & programing • Windows based programming software available • Designed to EN54 Pt.2 & 4 • Flash memory microprocessor for easy software upgrades • Remote silence • Event retrieval (last 32) • Minimum of 2 sounder outputs • Maximum of 10 sounder outputs • Set engineer’s access code • Two or four wire repeaters RS485 • Precinct/Class change • Common fire and fault relays, monitored • Voltage free aux. relays, programmable zonally • Zonal engineer's test • Sounder walk test • Detector removal walk test • Disable zones and sounder circuits • ‘Auto-learn’ repeater addressing

• • • •

Smoke/Heat Detectors: Eurotech Conventional range EURVC-P Optical EURVC-DP Dual Optical EURVC-H-A2S Heat EURVC-H-CS Heat EURB-4SE-SW Sav-wire Base Call Point: Must have 470 OHM Series resistor fitted and Polarising diode Sounders: Use polarised and suppressed, light current 24vdc electronic sounders or bells

Extrernal Indicators – Level 1 • Common Fire. Zonal Fire • Detector Removed, Common Fault • Remote Fire/Fault activated/disabled • Test Mode, Disabled • Sounder Fault, Program Mode • ARW, Earth, PSU • Supply healthy

Extrernal Indicators – Level 2 • Keyswitch ‘activate controls’ • Keypad for controls and programing • Keypad functions: ‘Silence Alarms’ ‘Reset’ ‘Sound Alarms’ ‘Isolate Remote’

Buzzer volume control Battery start switch Programming DIL switch PSU Voltage control

Keypad programming via engineers code or PC with ‘Windows’ based software • Quantity of Repeaters 0-8 units • Zone delay 0-255 seconds • Fault latch, for locating intermittent faults • Programmable outputs • Programmable monitored circuits • Invert common fault voltage output • Invert common fault monitored output • Zonal fire latch/non latch • Zonal pre-1988 (short circuit = fire) • Detector removal options, chottky, zener or none • Delayed zone operation • Sounder circuit responses (zonal), continuous, pulsing, or none • Sounder circuit responses (global), continuous, pulsing, or none • ‘Twin Wire’ sounder mode EN54 or BS5839 • Select zone of origin sounders • Select zonal sounders • Voltage output responses (zonal), continuous, pulsing, or none • Voltage output responses (global), continuous, pulsing, or none • Select voltage outputs, clear on silence or reset • Select voltage outputs, isolateable or not • Monitored circuit responses (zonal), continuous, pulsing, or none • Monitored circuit responses (global), continuous, pulsing, or none • Monitored circuits clear on silence or reset • Monitored circuits isolateable or not • Interrogate log • Set defaults • Set engineer’s access code • Remote fire/fault O/Ps convert to sounder circuits

Additional Specification • Power Supply: 230V 50Hz Current limited to 3 Amp 24V DC for SLA batteries • Cabinet: 18 swq mild steel 20mm knockouts, colour reference: Radon MW334E Interpon Powdercoat • End of Line: Sounder and Detection circuits 4K7 OHM

Additional Equiptment FCRPXLK-8

FCRPXLK-E

BDXLK-8 FMK-XLK-A USB-LEAD

RS-LEAD

Repeater panel, 8 zone, fully functional, 2 wire Connection, 2 Amp PSU Budget Repeater panel, 16 zone, silence and reset only, no PSU 8 way programmable bell driver unit, boxed Flush mounting kit for Excel 2-8 zone PC programming and download lead kit for USB port PC programming and download lead kit for Serial port

Internal Indicators – Level 3 • PSU Faults: battery, mains, earth and voltage (high/low) • Communications link TX/RX

31


Precept EN 2,4,8,16 & 32 Zone Conventional Panels

Hardware Sturdy 1.5mm mild steel enclosure with textured, off white, paint finish (RAL 7035 as standard) l

Top knockouts for 20mm cable glands, rear oval cable knockouts & one knockout provided at bottom of panel

l

Quality fibreglass circuit boards, surface mount components

l

Display mounted controls access keyswitch

l

Generous internal clearances for cabling and glanding

l

2,4,8 & 16 Zone models house up to 12Ah SLA battery set. 32 zone houses up to 18Ah set

l

Motherboard & power supply/transformer mounted on easily removable chassis for ease of installation

l

Text inserts used for zone descriptions

l

Insertable text option for controls & panel indications allowing easier multilingual support

Overview The Precept EN range of conventional control panels are powerful yet user friendly. They are designed and manufactured to a high standard and are approved by LPCB to EN54 parts 2 & 4. The original Precept panel had earned a reputation, over many years, for its reliability & quality and the Precept EN range is a worthy successor offering all the features you could wish for in one high quality, aesthetically pleasing and reliable package. Since its launch in 2003 it has proved to be an excellent product selling worldwide into many markets. These panels are available in 2,4,8,16 & 32 zone versions along with suitable repeaters for all models. The 8 - 32 zone panel models are capable to drive any combination of 8 channel output expansion boards (relays, alarm circuits & open collector 0v outputs) which can be set to be zonally activated or common output modes. Each panel has extensive configuration options but remains easy to install, program and operate. This is supported by comprehensive documentation on commissioning, operating and maintenance. The panels are designed to work with a wide range of manufacturers detectors and are able to cope with many types of installation (new or retrofit).

Eurotech Fire Systems Limited www.eurotechfire.com | T +44 (0) 203 141 0999 | F +44 (0) 239 225 2554 | E info@eurotechfire.com


Precept EN Specifications

Controls & Panel Connections Detection

Designed to work with a wide range of Indications manufacturers detectors (up to 32 detectors per zone) 2,4,8,16 & 32 zone versions available fully fault monitored Zone activation resistance typically 470 or 680 Ohms eg. callpoint or input signal 22 uF Capacitor zone EOL monitoring. IS (Intrinsically Safe) zones selectable In this mode the EOL device is changed to a 10K resistor NLZ (Non Latching Zones) selectable output relay disablement option for this function Short circuit activated zones selectable ‘Indication only’ zone mode option

Sounder O/P

4 fully monitored sounder (bell/alarm) circuits 24V active (2 zone panel has 2 circuits) Remote inputs for SILENCE, EVAC, RESET, CLASS CHANGE (0V applied activation) Monitored relay outputs for FAULT ROUTING, FIRE ROUTING & FIRE PROTECTION (configurable to volt free) Open Collector (0V switched) outputs for zones 1-4, disablement active, evacuate & buzzer active. Volt free reset relay - active for 10 Seconds on panel reset. Add-on 8 way expansion modules (sounders, LED driver & Volt free relays) for 8 - 32 zone panels. 1 x 8 way board can be fitted in standard panel and 2 x 8 way boards can be fitted in the large 8/16 zone panel enclosures. Separate expansion boxes are available for increased capacity. Auxiliary 24V DC output (electronically fused– clears on reset)

Inputs

Outputs

User Controls Controls Enable key switch Silence/Resound alarms Evacuate Reset System Disable & Enable Menu Up & Down Select On/Off Test Display Silence Buzzer Delay On/Off & Override Test

Panel Functions

Power Supply On Power supply fault Zone fire, Fault & Disabled Common Fire Fire routing active System fault General Fault Earth fault Fuse failed Repeater fault Sounder fault/disabled Sounder test Fire protection output fault/disabled Fire routing fault/disabled Fault routing fault/disabled Test mode active Disablement Buzzer silenced Delay on/off/override Select mode active Evacuate Extensive configuration and programming options to cater for individual requirements. Engineer can program the many settings via use of internal dip switches combined with front panel controls Numerous disablement options (sounder circuits, zones, relays, panel buzzer & earth fault monitoring) One man zone & sounder test modes (individual zones can be selected) Delay mode options - sounders and relay outputs can be disabled for a 1-9 minute time period if certain programmed zones are activated (not EN54 compliant in this mode) 2 stage delay mode - panel will delay sounding alarms etc. for 2 minutes, if acknowledged at the panel within that period then the delay mode reverts to continue remaining overall preprogrammed minutes Zonal or general alarm options with continuous or pulsed ‘non-alarm zone’ sounder modes Clock/timer module option

33


Precept EN Specifications

Panel Specifications Function

2 Zone

4 Zone

8 Zone

16 Zone

32 Zone

Mains Supply (tolerance +10 / -15%)

230V ac

230V ac

230V ac

230V ac

230V ac

85W

85W

165W

165W

240W

Mains Fuse (BEAB Approved Type)

1A 20mm

1A 20mm

3.15A 20mm

3.15A 20mm

3.15A 20mm

Battery Fuse

2A 20mm

2A 20mm

5A 20mm

5A 20mm

6.15A 20mm

Max. PSU/Batt. Charger Output

1.5V

1.5V

3A

3A

5A

Sounder Circuits (24V nominal)

2 @ 500 mA

4 @ 500 mA

4@1A

4@1A

500mA

500mA

1A

1A

1A

2 x 12 Ah

2 x 12 Ah

2 x 12 Ah

2 x 12 Ah

2 x 18 Ah

Mains Fail Batt. Current (no load)

45 mA

45 mA

45 mA

45 mA

55 mA

As Above - 1 Zone In Alarm

80 mA

80 mA

80 mA

80 mA

90 mA

Mains Failed Voltage Output

19.2 - 27V

19.2 - 27V

19.2 - 27V

19.2 - 27V

19.2 - 27V

Repeater Panel Option

Yes

Yes

Yes

Yes

Yes

Output Expansion Capability

No

No

Yes

Yes

Yes

Standard Zonal Outputs

Zones 1-2

Zones 1-2

Zones 1-4

Zones 1-4

Zones 1-4

Operating Temperature

-5° to 40°C

-5° to 40°C

-5° to 40°C

-5° to 40°C

-5° to 40°C

Operating Humidity

5% to 95%

5% to 95%

5% to 95%

5% to 95%

5% to 95%

Panel Dimensions (mm W x H x D)

325 x 370 x 126

325 x 370 x 126

325 x 370 x 126

325 x 370 x 126

400 x 441 x 131

6.2 Kg

6.2 Kg

7.1 Kg

7.1 Kg

10.25 Kg

RAL 7035 Lt. Grey

RAL 7035 Lt. Grey

RAL 7035 Lt. Grey

RAL 7035 Lt. Grey

RAL 7035 Lt. Grey

N/A

N/A

8 x 500 mA

8 x 500 mA

8 x 500 mA

Max. Power Consumption

Aux DC Output (24V nominal) Max. Size Battery Space

Native Panel Weight (no batteries or printer)

Enclosure Colour C1635 8 Way Sounder Module

4@1A

NOTE: Although the Aux DC and Sounder outputs are rated/fused at the above stated values it should be noted that the overall power drawn by ancillary equipment must not exceed the maximum overall PSU output .

Eurotech Fire Systems Limited www.eurotechfire.com | T +44 (0) 203 141 0999 | F +44 (0) 239 225 2554 | E info@eurotechfire.com


Precept EN Specifications

Typical Terminal Arrangement (Precept EN 16 Zone)

Outputs: DIS = Disablement active EVAC = Evacuation active BUZ Active = Buzzer active

-

+

-

+

-

+

-

+

1

-

+

+

2

-

+

3

-

+

4

-

+

-

EVAC

-

+

8

Repeater

Buz Active

-

+

7

DIS

-

+

6

Class change

4

Alarm Circuits

5

RST

3

4

EVAC

2

3

0V

1

2

SIL

1

24V

Zone Circuits

Zone O/Ps

Outputs

SCN

Inputs Aux DC

B

A

Reset N/C

Inputs: SIL = Silence alarms EVAC = Evacuate RST = Reset

Lower terminal tier

Lower terminal tier

Upper terminal tier

Upper terminal tier

15

-

+ 16

Aux DC

Fault Routing

P

-

+

N/O

14

O/-

Zone Circuits

-

+

P

13

O/-

-

+

C/+

12

P

-

+

O/-

11

C/+

-

+

P

10

0V

-

+

C/+

9

24 V

-

+

Reset Fire Fire Routing Protection

O/- = Normally Open or -ve P = Pole C/+ = Normally Closed or +ve

Part No: 2605100

Precept EN 2 Zone Panel

2605101

Precept EN 4 Zone Panel

2605102

Precept EN 8 Zone Panel

2605103

Precept EN 16 Zone Panel

2605104

Precept EN 32 Zone Panel

35


Duo-Cel 2 -8 Zone Conventional EN54 Approved Panels EN54 (with CPD) approval is pending and will be realised in the near future

General Features 2,4 & 8 Zone versions available in an aesthetically pleasing design. l

Sturdy, flame retardant, ABS plastic enclosure with controls, zone text insert & indications overlay

l

Easy to install, program and use. Key operated controls access (no ‘user confuser’ codes!)

l

Panel can be surface or semi flush mounted & has 20mm cable gland breakouts

l

Comprehensive LED indications and user/engineer controls

l

Low standby power consumption.

l

4 Sounder circuits 4 & 8 zone, 2 on 2 zone panel. Zonal & Alert sounder options configurable

l

1.5A switched mode power supply with temperature compensated battery charging

l

Enclosure houses 3.4Ah SLA batteries as standard

l

8 Zone repeaters available with 24V or mains operation (suitable for 4 & 8 zone panels only)

10uF Capacitor for zone EOL device 10K Resistor for sounder circuit EOL device

Overview Based on the technology of our top range panels the Duo-Cel has been developed to bring our budget panel range up to date regarding functionality, and necessary approvals. The panel supports a wide variety of commonly available detectors, callpoints and sounders from various manufacturers and has many useful configurable options, inputs and outputs to aid with installation and retrofitting. * We normally insist that training is received from us before issue of programming software. Please contact your usual supplier about obtaining training and software.

Zone 1 non latching option Zone dependency function Callpoint Discrimination function Alert/Evac. callpoint function Zones, sounders & fire signal disablement Independent zone testing Sounder test mode Fault monitored fire signal output Earth fault monitoring Short circuit zone activation option (global) EOL zone resistor option for retrofitting (global)

Eurotech Fire Systems Limited www.eurotechfire.com | T +44 (0) 203 141 0999 | F +44 (0) 239 225 2554 | E info@eurotechfire.com


Duo-Cel Specifications

Specifications Function Mains Supply Voltage Mains Frequency Mains Fuse (Non Servicable) Battery Fuse

Duo-Cel 2 - 8 Zone

Mains Repeater

DC Repeater

230V ac (-15% to +10%)

230V ac (-15% to +10%)

N/A

47.5 - 63 Hz

47.5 - 63 Hz

N/A

3A 20mm Glass

3A 20mm Glass

N/A

2A 20mm FB Glass 2A 20mm FB Glass

Operating Temperature Range

N/A

-5° to 40° C

-5° to 40° C

-5° to 40° C

95%

95%

95%

28.15VDC >1.4A

28.15VDC >1.4A

N/A

1.5A 18-29V

1.5A 18-29V

N/A

Conventional Sounder Circuits

4 (2 On 2 Zone)

N/A

N/A

Max. Alarm Circuit Output

28.4VDC 500mA

N/A

N/A

Max. Aux DC Output

28.4VDC 250mA

28.4VDC 250mA

N/A

Battery Type (Set required for 24V)

3.4Ah - 12Ah SLA

3.4Ah - 12Ah SLA

N/A

S/by / Mains Fail Alarm Current 2 Zone

22mA / 63mA

N/A

N/A

S/by / Mains Fail Alarm Current 4 Zone

28mA / 76mA

-

-

S/by / Mains Fail Alarm Current 8 Zone

36mA / 84mA

17mA / 22mA

8mA / 13mA

DC Repeater Supply

N/A

N/A

20 - 30VDC

IP Rating

30

30

30

365 x 273 x 110

365 x 273 x 110

365 x 273 x 110

2.2 Kg

2.2 Kg

1.8 Kg

Light Grey RAL 7035

Light Grey RAL 7035

Light Grey RAL 7035

Max. Operating Humidity Max. Batt. Charger Output Max. PSU Output

Panel Dimensions (mm W x H x D) Native Panel Weight (no batteries or printer) Panel Colour

Note that Max. values take into consideration normal operation running on lowest temperature compensation

Part No: 2605542

Duo-Cel 2 Zone Panel

2605543

Duo-Cel 4 Zone Panel

2605544

Duo-Cel 8 Zone Panel

37


Duo-Cel Specifications

Controls & Panel Connections User Controls Controls Access Keyswitch Panel Evacuate Silence Buzzer Silence/Resound Alarms Reset Disable Test Select Indications

Repeater Comms.

Supply On General Fire General Fault General Test General Disablement Alert/Evac On Fire Signal On Fire Signal Fault PSU Fault Fuse Failed Repeater Fault Remote Control Fault Controls On Repeater 1,2 & 3 Fault Zone Fires Zone Faults 2 core screened RS485 data cable, 4 core if powered from panel

Panel Terminals

Zones + & Fire Signal + & Fire Relay N/C,N/O & POLE Fault Relay N/C,N/O & POLE Remote Controls Input & 0V Disable, Evacuate & Buzzer Active Outputs Aux. 24VDC & 0V Outputs Repeater A & B Comms. Alarm Circuits + & -

Other Inputs & Controls

Battery Spade Connectors Mounted On PCB Molex Power Supply Connector Engineers Alarm Counter Reset Button Dip switch activated programming options Earth Fault Disable link Firmware Programming Header

Remote I/P Details

Input: Class Change Alert Evacuate Silence Reset

Remote O/P Details

Evacuate Activated 50mA (30V) Buzzer Activated 50mA (30V) Disabled 50mA (30V) Fire Signal 28V 250mA (Monitored)

Eurotech Fire Systems Limited www.eurotechfire.com | T +44 (0) 203 141 0999 | F +44 (0) 239 225 2554 | E info@eurotechfire.com

Trigger Resistor Value: 4K7 2K2 1K 470R 220R

Conventional control panels  
Conventional control panels  
Advertisement