Issuu on Google+

RF Series

Shaft Mounted Gear Units

Superior Gear Technology

www.renold.com


RF Series - Shaft Mounted Helical Gear Units GEARS Hardened and ground gears.

ALLOY HOUSING is vacuum impregnated with Resinol RT (MIL-STD 276) for protection and sealing. No secondary finish required but readily accepts paint

OIL SEAL Two oil seals on request.

FLANGE Fully modular to NEMA C flange

LARGE CENTER DISTANCE On low speed gears REMOVABLE INSPECTION COVER Allows periodic inspection of gearing during routine maintenance

Applications:

l Conveyor Drives

l Sewage Treatment

l Mixer Drives

l Water Treatment

l Mining Industry

l Packaging Machinery

l Textiles

www.renold.com 2


Contents Page No HP RATING TABLES A.G.M.A Service Factor How to Use 1/3 HP 1/2 HP 3/4 HP 1 HP 1 1/ 2 HP 2 HP 3 HP 5 HP 7 1/ 2 HP How to Order

4 6 7 8 9 10 12 13 14 15 17 18

MAXIMUM RATINGS TABLES How to Use

20

DIMENSIONS DOUBLE-TRIPLE REDUCTION ALUMINUM F32A F33A F42A F43A F52A F53A

22 22 24 24 26 26

DIMENSIONS DOUBLE-TRIPLE REDUCTION CAST IRON F62C F63C

28 28

SPECIAL SIZE Gearbox FS20 Gearbox FS50

30 31

TECHNICAL INFORMATION Lubrication Overhung Loads and Thrust Loads Radial and Axial Loads Available Reaction Arm Available Output Flange Face Mounting Dimensions Input Bore/Flange for IEC Motors (Metric) Oil Levels Plug for 402A - 603C Double Oil Seal Kit for Output Shaft Special Output Shaft Bearings Protection Cups Input Shaft Bushings Metric Output Shaft Maintenance Check Lists Selection Check List Installation Check List Parts List Motor Dimensions Reference

32 34 35 36 37 37 38 38 39 39 39 39 40 41 42 42 44 46

www.renold.com 3


A.G.M.A Service Factors

Service Factors

The gearbox speed reducer ratings in this catalogue are for a 1.00 service factor or( Class I )* service. A 1.00 service factor applies when the use of the reducer is for continuous service free from recurrent shock loading and does not exceed 8 hours per day for Aluminum and 10 hours per day for Cast Iron. When operating conditions are different from those described above, the input horsepower and torque ratings shown in this catalogue must be divided by the appropriate service factor indicated in the table below. The catalogue ratings may be used without adjustments if the actual driven machine horsepower and torque requirements are multiplied by the appropriate service factor indicated in the table below. * Class I: ( Minumum 0.8 Service Factor ) A gearmotor can operate with steady loads not exceeding the normal rating and 8-10 hours of running time per day.

A.G.M.A. GEAR REDUCER LOAD CLASSIFICATIONS This chart is a guideline for the types of loads applied to the following. Parallel ( helical ) reducers.

DURATION OF SERVICE ( HOURS PER DAY )

½ Hours or less 2 Hours Intermittently 10 Hours 24 Hours

LOAD CLASSIFICATION OF THE MACHINERY DESIGN

WHEN FREQUENT STOPS/STARTS ARE APPLIED IN EXCESS OF 10/HOUR

UNIFORM

MODERATE SHOCK

HEAVY SHOCK

UNIFORM

MODERATE SHOCK

HEAVY SHOCK

0.80

0.80

1.00

0.80

0.80

1.25

1.00

1.00

1.25

1.0

1.25

1.50

1.00

1.25

1.50

1.25

1.50

1.75

1.25

1.50

1.75

1.50

1.75

2.00

ENGINE DRIVEN APPLICATIONS For multiple cylinder engine drive applications, the service factors are greater then those shown above for electric drives. Service factors for multiple cylinder engine drives may be determined from the conversion table below. 8 - 10 HOUR SERVICE

24 HOUR SERVICE

LOADING

ELECTRIC MOTOR DRIVE

MULTIPLE CYLINDER ENGINE*

ELECTRIC MOTOR DRIVE

MULTIPLE CYLINDER ENGINE*

UNIFORM MODERATE HEAVY

1.00

1.25

1.25

1.50

1.25

1.50

1.50

1.75

1.75

2.00

1.75

2.00

* These service factors apply essentially to driven applications without extreme variations. For application assistance refer to Renold.

Normal starting or occasional peak loads, two or three times per day, up to 300% of catalogue rating at 1800 RPM are permissible. If either the frequency or the magnitude of these loads exceed the above limits, a higher service factor is required and the application should be referred to Renold. Gearbox reducers are not to be considered fail safe or self-locking devices. If these features are required, a properly sized, independent holding device should be utilized. Depending upon gear geometry and operating conditions, gearbox reducers may or may not backdrive. Special consideration should be given to high inertia loads connected to the reducer output shaft. Consult Renold for further details. Reducers driven by brakemotors must be sized to accomodate motor driving, brake and inertia loads to prevent the breaking torque or inertia loads from exceeding the motor rating. ! CAUTION For safety, purchaser or user should provide protective guards over shaft extensions and any couplings sheaves and belts, sprockets and chains, etc., mounted thereon. www.renold.com 4


A.G.M.A.

Service Factors

SPEED REDUCER LOAD CLASSIFICATION Application

Service Factor 8 to 10 Hour Service

1.00 1.25 1.75

1.25 1.50 Refer to factory

1.00 1.25

Centrifugal Lobe

1.00 1.25

Bottling Machinery Brew Kettles, continuos duty Cookers, continuos duty Mash Tubs, continuos duty Scale Hopper ( Frequent Starting )

1.25 Refer to factory 1.50 1.25

1.25 1.00 1.25 1.25

1.50 1.25 1.50 1.50

LAUNDRY WASHERS

1.25

1.50

LAUNDRY TUMBLERS

1.25

1.50

Centrifugal Cooling rowers Large ( Mine, etc. ) Light small diameter

1.25 1.50

HOISTS - See Cranes 1.00 1.00 1.00 1.00 1.25

1.25 1.25 1.25 1.25 1.50 1.75

CAR PULLERS

1.25

1.50

CLARIFIERS

1.00

1.25

CLASSIFIERS

1.25

1.50

CLAY WORKING MACHINERY 1.75 1.75 1.25 1.25

1.75 1.75 1.50 1.50

1.00 1.25

1.25 1.50

1.25 Refer to factory

1.50 Refer to factory

1.00

1.25

1.25 1.25 1.25 1.75

1.50 1.50 1.50 1.75

1.25 1.75 Refer to factory

1.50 1.75 Refer to factory

1.25 1.75 1.75 1.25 1.25

1.50 1.75 1.75 1.50 1.50

COMPRESSORS

8 to 10 24 Hour Hour Service Service

Punch Press (Gear connected to load ) Notching press ( Belt driven ) Plate planers Other machine tools main drives Auxiliary drives ( Feed Traverse, etc. ) METAL MILLS Draw Bench Carriages & Main Drives Forming Machines Pinch, Dryer and Scrubber Rolls ( Reversing ) Slitters Small rolling mill, drives Table Conveyors( Non reverse ) Table Conveyors( Reversing ) Wire Drawing & Flattening Machines

Mixer Rubber calender Rubber mill Tire building machines Tire and tube press openers Tubers or strainers

1.75 Refer to Factory -

1.75 1.75 1.75 Refer to Factory 1.50

1.00 1.00

1.25 1.25

2.00

2.00

1.25

1.50

1.00

2.00

1.25 Refer to Factory Refer to Factory

1.50 Refer to Factory Refer to Factory

1.00

1.25

1.25 1.00

1.50 1.25

1.75 1.25 1.25 1.25

1.75 1.50 1.50 1.50

1.25 1.25 1.25 1.25 1.25

1.50 1.50 1.50 1.50 1.50

PUMPS Centrifugal Gear and rotary Constant density fluid Gear and rotary Variable density fluid Proportioning pumps Reciprocating with open discharge Reciprocating multicylinder, double acting Reciprocating single cylinder Reversing duty

SEWAGE DISPOSAL EQUIPMENT

MACHINE TOOLS 1.75

Centrifugal Lobe Reciprocating Multi-cylinders ( within 3% cyclic variation ) Reciprocating, Single Cylinder

1.00 Refer to factory 1.25 1.00

FANS

Beet Slicers Cereal Cookers Dough Mixer Meal Grinders

CAR DUMPERS

Brick Press Briquette Machines Clay Working Machinery Plug Mill

Refer to factory

FOOD INDUSTRY

BREWING & DlSTILLING

Service Factor

RUBBER INDUSTRY Refer to factory

1.25 1.50

BLOWERS

Application

8 to 10 24 Hour Hour Service Service ( Conveyor type same as conveyors )

AGITATORS Pure liquids Liquids-Variable Densily

Service Factor

ELEVATORS

NORMAL INDUSTRIAL USAGE Steady load not exceeding normal rating of motor or intermittent shock. Moderate shock Heavy shock

Application

24 Hour Service

Inside service 1.75 Refer to factory 1.75 1.25

1.75 Refer to factory 1.75 1.50

1.00

1.25

1.00

1.25

1.75 Refer to factory 1.25 1.75 1.25 Refer to factory 1.25

1.75 Refer to factory 1.50 1.75 1.50 Refer to factory 1.50

1.25 1.75

1.50 1.50 1.50 1.75

1.25 1.00 1.00 1.25

1.50 1.25 1.50

1.25 1.00

1.50 1.25

1.00 1.00 1.00 1.25 1.25 1.25 1.25 1.25 1.25

1.25 1.25 1.25 1.50 1.50 1.50 1.50 1.75 1.50

SCREENS Rotary - Stone or gravel Traveling Water Intake

OIL INDUSTRY Oil well pumping ( Not over 150% peak torque ) Refineries Chillers, rotary kiln Paraffin filter press

TEXTILE INDUSTRY Batchers, calenders Card Machines, dry cans Dyeing Machinery, mangles Nappers, soapers Spinners tenter frames

CONVEYORS ( Uniformly loaded or Fed ) Flighl, Oven, Screw

MlLLS ( Rotary Type )

CONVEYORS ( Heavy duty or dual drive not uniformly fed ) Apron, Assembly, Belt, Bucket, Flight, Oven Screw, Reciprocating, Shaker

DREDGES Cable Reels, Conveyors Cutter Head Drives Jig Drives, Screen Drives Stackers Utilily Winches

MIXERS Concrete Mixers - continuos Concrete Mixers - intermittent Constant density Variable density

LINE SHAFTS

CRANES & HOISTS Main Hoists - Medium duty - Heavy duty Skip hoists Travel motion Trolley motion

Ball, dryer cooler Cement kilns, pebble rod Kilns Tumbling barrels

Driving processing equipment Other line shafts

PAPER MILL Bleacher presses Conveyors, suction roll Winders Agitators ( Mixers ) Dryer, felt stretcher Stock chest calenders Beater & Pulper Jordans Couch, cylinders

The application service factors shown above are considered typical for most applications. Where loads are lighter than normal, where units are operated seasonally, or where unusual severe conditions exist, refer to Renold. For application assistance refer to Renold.

www.renold.com 5


Selection by Hp and Speed Step 1:

1/3

HP

Find the desired HP and output speed from pages 07 to 17 NEMA Frame Selections 1750 RPM Input Nr° Red.

Output Shaft DIA

Cast Iron

Ratio

Aluminum

Two or Three Stages Two or Three Stages

Output Output Speed Service Torque (RPM) Factor (Ib-in)

Dim. on Page

Available Motor Flanges

218

15.96

91

8.03

2

F32

-

1.00

-

143-5TC

56C

168

13.42

118

10.40

2

F32

-

1.00

-

143-5TC

56C

35

*If the application requires a service factor greater than 1.0, select a higher horsepower rated reducer. For example, if the required horsepower is 1 but the service factor from the AGMA table is 2, select a reducer rated for 2 HP ( 1HP times Service Factor of 2 = 2HP ) and of the desired output speed. However, use a 1HP drive motor.

Step 2:

Select the reducer type: Two or three Stages

Nr° Red.

Output Shaft DIA

Cast Iron

Ratio

Aluminum

Two or Three Stages Two or Three Stages

Output Output Speed Service Torque (RPM) Factor (Ib-in)

Double and Triple Reduction (Alluminum)

Dim. on Page

Available Motor Flanges

Double and Triple Reduction (Cast Iron)

* As an alternative to Step 1 and 2 make a quick selection directly from the Hp tables on pages 22 to 29.

Step 3:

Check others selection details.

Nr° Red.

Output Shaft DIA

Cast Iron

Ratio

Aluminum

Two or Three Stages Two or Three Stages

Output Output Speed Service Torque (RPM) Factor (Ib-in)

Dim. on Page

Available Motor Flanges

218

15.96

91

8.03

2

F32

-

1.00

-

143-5TC

56C

168

13.42

118

10.40

2

F32

-

1.00

-

143-5TC

56C

Note the Ratio Read the Torque

Note the Note the Output Number (Stage) Shaft ( Diameter ) of reductions

Step 4:

Select the Motor Flange

See additional Selection Check List on page 44 See “How to Order” on pages 18 - 19 for product codes and options.

www.renold.com 6

See Pages for Dimensions

35


1/3

HP

NEMA Frame Selections 1750 RPM Input

Nr째 Red.

Output Shaft DIA

Cast Iron

Ratio

Aluminum

Two or Three Stages Two or Three Stages

Output Output Speed Service Torque (RPM) Factor (Ib-in)

Dim. on Page

Available Motor Flanges

218

15.96

91

8.03

2

F32

-

1.00

-

143-5TC

56C

23

168

13.42

118

10.40

2

F32

-

1.00

-

143-5TC

56C

23

120

10.38

165

14.53

2

F32

-

1.00

-

143-5TC

56C

23

104

8.96

192

16.84

2

F32

-

1.00

-

143-5TC

56C

23

103

11.08

194

17.02

2

F42

-

1.25

-

143-5TC

56C

25

89

7.63

225

19.76

2

F32

-

1.00

-

143-5TC

56C

23

74

6.39

269

23.59

2

F32

-

1.00

-

143-5TC

56C

23

54

4.68

367

32.20

2

F32

-

1.00

-

143-5TC

56C

23

47

13.63

411

37.23

3

-

F63

1.50

-

143-5TC

56C

29

45

3.28

445

39.05

2

F32

-

1.00

-

143-5TC

56C

23

42

3.62

475

41.68

2

F32

-

1.00

-

143-5TC

56C

23

41

3.55

484

42.48

2

F42

-

1.25

-

143-5TC

56C

25

33

3.54

599

52.62

2

F42

-

1.25

-

143-5TC

56C

25

32

2.77

619

54.39

2

F32

-

1.00

-

143-5TC

56C

23

29

4.38

661

59.92

3

F43

-

1.25

-

-

56C

25

27

3.22

726

65.81

3

F43

-

1.25

-

-

56C

25

25

1.95

791

69.49

2

F42

-

1.25

-

143-5TC

56C

25

25

3.78

766

69.45

3

F43

-

1.25

-

-

56C

25

24

1.99

818

71.82

2

F32

-

1.00

-

143-5TC

56C

23

21

1.54

946

83.04

2

F32

-

1.00

-

143-5TC

56C

23

21

3.22

899

81.52

3

F43

-

1.25

-

-

56C

25

18

2.70

1073

97.30

3

F43

-

1.25

-

-

56C

25

17

1.47

1170

106.07

3

F33

-

1.00

-

-

56C

23

16

1.17

1249

109.66

2

F32

-

1.00

-

143-5TC

56C

23

16

1.97

1183

107.22

3

F43

-

1.25

-

-

56C

25

15

1.32

1302

118.06

3

F33

-

1.00

-

-

56C

23

15

2.11

1260

114.22

3

F43

-

1.25

-

-

56C

25

13

1.12

1527

138.43

3

F33

-

1.00

-

-

56C

23

13

1.77

1504

136.33

3

F43

-

1.25

-

-

56C

25

12

1.10

1554

140.92

3

F33

-

1.00

-

-

56C

23

11

2.52

1740

157.74

3

F53

-

1.375

-

143-5TC

56C

27

10.3

2.65

1867

169.22

3

-

F63

1.50

-

143-5TC

56C

29

9.8

2.30

1975

179.06

3

F53

-

1.375

-

143-5TC

56C

27

9.5

2.11

2031

184.15

3

F53

-

1.375

-

143-5TC

56C

27

9.4

1.30

2053

186.09

3

F43

-

1.25

-

-

56C

25

8.5

1.93

2271

205.87

3

F53

-

1.375

-

143-5TC

56C

27

7.7

2.22

2511

227.69

3

-

F63

1.50

-

143-5TC

56C

29

7.6

1.15

2525

228.89

3

F43

-

1.25

-

-

56C

25

3

F53

-

1.375

-

143-5TC

56C

27

3

F43

-

1.25

-

-

56C

25

7.3

1.62

2651

240.34

7.2

0.99

2679

242.87

6.8

1.97

2837

257.23

3

-

F63

1.50

-

143-5TC

56C

29

6.4

1.46

2998

271.85

3

F53

-

1.375

-

143-5TC

56C

27

5.8

1.68

3316

300.66

3

-

F63

1.00

-

143-5TC

56C

29

See How To Order on pages 18 - 19 www.renold.com 7

Input shaft bushing required - see page 41.


1/3

HP

NEMA Frame Selections 1750 RPM Input

5.5

1.23

3500

Nr째 Red.

317.36

3

Output Shaft DIA

Cast Iron

Ratio

Aluminum

Two or Three Stages Two or Three Stages

Output Output Speed Service Torque (RPM) Factor (Ib-in)

F53

-

1.00

-

143-5TC

HP

56C

27

Input shaft bushing required - see page 41.

See How To Order on pages 18 - 19

1/2

Dim. on Page

Available Motor Flanges

NEMA Frame Selections 1750 RPM Input Output Shaft DIA

Cast Iron

Ratio

Nr째 Red.

Aluminum

Two or Three Stages Two or Three Stages

Output Output Speed Service Torque (RPM) Factor (Ib-in) 10.54

139

8.03

2

F32

-

1.00

-

168

8.86

179

10.40

2

F32

-

1.00

-

120

14.53

251

14.53

2

F32

-

1.00

-

104

5.91

290

16.84

2

F32

-

1.00

-

103

7.31

294

17.02

2

F42

-

1.25

-

89

5.04

341

19.76

2

F32

-

1.00

74

4.22

407

23.59

2

F32

-

1.00

54

3.09

555

32.20

2

F32

-

47

9.00

622

37.23

3

-

F63

45

2.17

674

39.05

2

F32

42

2.39

719

41.68

2

41

2.34

733

42.48

2

33

2.34

908

52.62

32

1.83

938

54.39

29

2.89

1001

27

2.12

1100

25

1.29

25

2.49

24 21

218

Dim. on Page

Available Motor Flanges 143-5TC

56C

23

143-5TC

56C

23

143-5TC

56C

23

143-5TC

56C

23

143-5TC

56C

25

-

143-5TC

56C

23

-

143-5TC

56C

23

1.00

-

143-5TC

56C

23

1.50

-

143-5TC

56C

29

-

1.00

-

143-5TC

56C

23

F32

-

1.00

-

143-5TC

56C

23

F42

-

1.25

-

143-5TC

56C

25

2

F42

-

1.25

-

143-5TC

56C

25

2

F32

-

1.00

-

143-5TC

56C

23

59.92

3

F43

-

1.25

-

-

56C

25

65.81

3

F43

-

1.25

-

-

56C

25

1199

69.49

2

F42

-

1.25

-

143-5TC

56C

25

1160

69.45

3

F43

-

1.25

-

-

56C

25

1.32

1239

71.82

2

F32

-

1.00

-

143-5TC

56C

23

1.02

1432

83.04

2

F32

-

1.00

-

143-5TC

56C

23

21

2.12

1362

81.52

3

F43

-

1.25

-

-

56C

25

18

1.78

1626

97.30

3

F43

-

1.25

-

-

56C

25

18

2.71

1618

96.82

3

F53

-

1.375

-

143-5TC

56C

27

17

0.97

1772

106.07

3

F33

-

1.00

-

-

56C

23

16

1.30

1792

107.22

3

F43

-

1.25

-

-

56C

25

15

2.27

1931

115.56

3

F53

-

1.375

-

143-5TC

56C

27

15

1.39

1908

114.22

3

F43

-

1.25

-

-

56C

25

14

2.28

2167

129.66

3

-

F63

1.50

-

143-5TC

56C

29

13

1.17

2278

136.33

3

F43

-

1.25

-

-

56C

25

13

1.98

2293

137.20

3

F53

-

1.375

-

143-5TC

56C

27

12

2.24

2494

149.26

3

-

F63

1.50

-

143-5TC

56C

29

11

1.66

2636

157.74

3

F53

-

1.375

-

143-5TC

56C

27

See How To Order on pages 18 - 19 www.renold.com 8

Input shaft bushing required - see page 41.


1/2

HP

NEMA Frame Selections 1750 RPM Input

Nr째 Red.

Output Shaft DIA

Cast Iron

Ratio

Aluminum

Two or Three Stages Two or Three Stages

Output Output Speed Service Torque (RPM) Factor (Ib-in)

Dim. on Page

Available Motor Flanges

10.3

1.75

2828

169.22

3

-

F63

1.50

-

143-5TC

56C

29

10

1.91

2915

174.46

3

-

F63

1.50

-

143-5TC

56C

29

9.8

1.52

2992

179.06

3

F53

-

1.375

-

143-5TC

56C

27

9.5

1.40

3077

184.15

3

F53

-

1.375

-

143-5TC

56C

27

9

1.72

3255

194.80

3

-

F63

1.50

-

143-5TC

56C

29

8.5

1.27

3440

205.87

3

F53

-

1.375

-

143-5TC

56C

27

7.7

1.46

3805

227.69

3

-

F63

1.50

-

143-5TC

56C

29

7.3

1.07

4016

240.34

3

F53

-

1.375

-

143-5TC

56C

27

6.8

1.30

4298

257.23

3

-

F63

1.50

-

143-5TC

56C

29

6.4

0.96

4542

271.85

3

F53

-

1.375

-

143-5TC

56C

27

5.8

1.11

5024

300.66

3

-

F63

1.50

-

143-5TC

56C

29

Input shaft bushing required - see page 41.

See How To Order on pages 18 - 19

3/4

HP

NEMA Frame Selections 1750 RPM Input

266

14.62

170

Output Shaft DIA

Cast Iron

Aluminum

Two or Thee Stages Two or Thee Stages

Output Output Speed Service Torque (RPM) Factor (Ib-in)

Dim. on Page

Available Motor Flanges

Ratio

Nr째 Red.

6.57

2

F52

-

1.375

182-4TC

143-5TC

-

27

232

13.15

196

7.56

2

F52

-

1.375

182-4TC

143-5TC

-

27

218

7.01

208

8.03

2

F32

-

1.00

-

143-5TC

56C

23

198

14.27

229

8.82

2

F52

-

1.375

182-4TC

143-5TC

-

27

168

5.90

269

10.40

2

F32

-

1.00

-

143-5TC

56C

23

120

4.56

376

14.53

2

F32

-

1.00

-

143-5TC

56C

23

104

3.94

436

16.84

2

F32

-

1.00

-

143-5TC

56C

23

89

3.35

512

19.76

2

F32

-

1.00

-

143-5TC

56C

23

83

4.97

546

21.08

2

F42

-

1.25

-

143-5TC

56C

25

74

2.81

611

23.59

2

F32

-

1.00

-

143-5TC

56C

23

68

2.59

663

25.58

2

F32

-

1.00

-

143-5TC

56C

23

54

2.06

834

32.20

2

F32

-

1.00

-

143-5TC

56C

23

47

2.28

941

37.47

3

F43

-

1.25

-

143-5TC

56C

25

45

1.44

1012

39.05

2

F32

-

1.00

-

143-5TC

56C

23

43

2.46

1045

40.32

2

F42

-

1.25

-

143-5TC

56C

25

42

1.59

1080

41.68

2

F32

-

1.00

-

143-5TC

56C

23

41

1.56

1101

42.48

2

F42

-

1.25

-

143-5TC

56C

25

36

1.92

1214

48.37

3

F43

-

1.25

-

143-5TC

56C

25

33

1.55

1364

52.62

2

F42

-

1.25

-

143-5TC

56C

25

32

1.22

1410

54.39

2

F32

-

1.00

-

143-5TC

56C

23

29

1.92

1504

59.92

3

F43

-

1.25

-

143-5TC

56C

25

29

2.49

1582

61.03

2

F52

-

1.375

182-4TC

143-5TC

-

27

25

1.66

1744

69.45

3

F43

-

1.25

-

143-5TC

56C

25

See How To Order on pages 18 - 19 www.renold.com 9

Input shaft bushing required - see page 41.


3/4

HP

NEMA Frame Selections 1750 RPM Input

Nr째 Red.

Output Shaft DIA

Cast Iron

Ratio

Aluminum

Two or Three Stages Two or Three Stages

Output Output Speed Service Torque (RPM) Factor (Ib-in)

Dim. on Page

Available Motor Flanges

25

2.30

1846

71.25

2

F52

-

1.375

182-4TC

143-5TC

-

27

21

1.41

2047

81.52

3

F43

-

1.25

-

143-5TC

56C

25

21

2.11

2071

82.48

3

F53

-

1.375

-

143-5TC

56C

27

19

2.43

2300

91.61

3

-

F63

1.50

-

143-5TC

56C

29

18

1.18

2443

97.30

3

F43

-

1.25

-

143-5TC

56C

25

18

1.80

2431

96.82

3

F53

-

1.375

-

143-5TC

56C

27

16

2.04

2745

109.35

3

-

F63

1.50

-

143-5TC

56C

29

15

0.93

2867

114.22

3

F43

-

1.25

-

143-5TC

56C

25

15

1.51

2901

115.56

3

F53

-

1.375

-

143-5TC

56C

27

14

1.52

3255

129.66

3

-

F63

1.50

-

143-5TC

56C

29

13

1.32

3444

137.20

3

F53

-

1.375

-

143-5TC

56C

27

12

1.49

3747

149.26

3

-

F63

1.50

-

143-5TC

56C

29

11

1.11

3960

157.74

3

F53

-

1.375

-

143-5TC

56C

27

10.3

1.16

4248

169.22

3

-

F63

1.50

-

143-5TC

56C

29

10

1.27

4380

174.46

3

-

F63

1.50

-

143-5TC

56C

29

9.8

1.01

4495

179.06

3

F53

-

1.375

-

143-5TC

56C

27

9.5

0.93

4623

184.15

3

F53

-

1.375

-

143-5TC

56C

27

8.9

1.14

4891

194.80

3

-

F63

1.50

-

143-5TC

56C

29

7.7

0.97

5716

227.69

3

-

F63

1.50

-

143-5TC

56C

29

Input shaft bushing required - see page 41.

See How To Order on pages 18 - 19

1 HP

NEMA Frame Selections 1750 RPM Input Output Shaft DIA

Cast Iron

Ratio

Nr째 Red.

Aluminum

Two or Three Stages Two or Three Stages

Output Output Speed Service Torque (RPM) Factor (Ib-in)

Dim. on Page

Available Motor Flanges -

27

143-5TC

-

27

143-5TC

56C

23

-

143-5TC

56C

23

-

143-5TC

56C

23

1.00

-

143-5TC

56C

23

1.00

-

143-5TC

56C

23

-

1.25

-

143-5TC

56C

25

F32

-

1.00

-

143-5TC

56C

23

2

F32

-

1.00

-

143-5TC

56C

23

29.54

2

F42

-

1.25

-

143-5TC

56C

25

32.20

2

F32

-

1.00

-

143-5TC

56C

23

266

10.98

227

6.57

2

F52

-

1.375

182-4TC

143-5TC

231

9.88

261

7.56

2

F52

-

1.375

182-4TC

218

5.27

277

8.03

2

F32

-

1.00

-

168

4.43

359

10.40

2

F32

-

1.00

120

3.43

501

14.53

2

F32

-

1.00

104

2.96

581

16.84

2

F32

-

89

2.52

682

19.76

2

F32

-

83

3.73

727

21.08

2

F42

74

2.11

814

23.59

2

68

1.95

882

25.58

59

2.61

1018

54

1.55

1111

53

2.61

1107

33.13

3

F43

-

1.25

-

143-5TC

56C

25

48

3.42

1256

36.43

2

-

F62

1.50

182-4TC

143-5TC

-

29

47

1.71

1252

37.47

3

F43

-

1.25

-

143-5TC

56C

25

See How To Order on pages 18 - 19 www.renold.com 10

Input shaft bushing required - see page 41.


1 HP

NEMA Frame Selections 1750 RPM Input Two or Three Stages Two or Three Stages

Dim. on Page

Ratio

Nr째 Red.

45

1.08

1347

39.05

2

F32

-

1.00

-

143-5TC

56C

23

45

2.94

1330

38.55

2

F52

-

1.375

182-4TC

143-5TC

-

27

43

1.85

1391

40.32

2

F42

-

1.25

-

143-5TC

56C

25

42

1.19

1438

41.68

2

F32

-

1.00

-

143-5TC

56C

23

41

1.17

1465

42.48

2

F42

-

1.25

-

143-5TC

56C

25

39

2.81

1529

44.32

2

F52

-

1.375

182-4TC

143-5TC

-

27

36

1.44

1617

48.37

3

F43

-

1.25

-

143-5TC

56C

25

34

2.38

1785

51.74

2

F52

-

1.375

182-4TC

143-5TC

-

27

33

1.17

1815

59.34

2

F42

-

1.25

-

143-5TC

56C

25

32

0.92

1876

54.39

2

F32

-

1.00

-

143-5TC

56C

23

30

1.87

1992

57.75

2

-

F62

1.50

182-4TC

143-5TC

-

29

30

2.53

1955

58.49

3

-

F63

1.50

-

143-5TC

56C

29

29

1.44

2002

59.92

3

F43

-

1.25

-

143-5TC

56C

25

29

1.87

2105

61.03

2

F52

-

1.375

182-4TC

143-5TC

-

27

28

2.20

2068

61.89

3

F53

-

1.375

-

143-5TC

56C

27

27

1.06

2199

65.81

3

F43

-

1.25

-

143-5TC

56C

25

26

1.87

2329

67.50

2

-

F62

1.50

182-4TC

143-5TC

-

29

26

2.49

2250

67.34

3

-

F63

1.50

-

143-5TC

56C

29

25

1.25

2321

69.45

3

F43

-

1.25

-

143-5TC

56C

25

25

1.73

2458

71.25

2

F52

-

1.375

182-4TC

143-5TC

-

27

25

1.84

2378

71.16

3

F53

-

1.375

-

143-5TC

56C

25

22

2.15

2608

78.05

3

-

F63

1.50

-

143-5TC

56C

29

21

1.06

2724

81.52

3

F43

-

1.25

-

143-5TC

56C

25

21

1.59

2756

82.48

3

F53

-

1.375

-

143-5TC

56C

27

19

1.83

3061

91.61

3

-

F63

1.50

-

143-5TC

56C

29

18

1.35

3235

96.82

3

F53

-

1.375

-

143-5TC

56C

25

16

1.53

3654

109.35

3

-

F63

1.50

-

143-5TC

56C

29

15

1.13

3862

115.56

3

F53

-

1.375

-

143-5TC

56C

25

14

1.14

4333

129.66

3

-

F63

1.50

-

143-5TC

56C

29

13

0.99

4585

137.20

3

F53

-

1.375

-

143-5TC

56C

25

12

1.12

4988

149.26

3

-

F63

1.50

-

143-5TC

56C

29

10

0.95

5830

174.46

3

-

F63

1.50

-

143-5TC

56C

29

Output Shaft DIA

Cast Iron

Aluminum

Output Output Speed Service Torque (RPM) Factor (Ib-in)

Available Motor Flanges

See How To Order on pages 18 - 19

www.renold.com 11

Input shaft bushing required - see page 41.


11/2 HP

NEMA Frame Selections 1750 RPM Input

Nr째 Red.

Output Shaft DIA

Cast Iron

Ratio

Aluminum

Two or Three Stages Two or Three Stages

Output Output Speed Service Torque (RPM) Factor (Ib-in)

Dim. on Page

Available Motor Flanges

266

7.32

340

6.57

2

F52

-

1.375

182-4TC

143-5TC

-

27

232

6.59

391

7.56

2

F52

-

1.375

182-4TC

143-5TC

-

27

218

3.51

416

8.03

2

F32

-

1.00

-

143-5TC

56C

23

216

3.88

420

8.12

2

F42

-

1.25

-

143-5TC

56C

25

174

3.30

520

10.06

2

F42

-

1.25

-

143-5TC

56C

25

168

2.95

538

10.40

2

F32

-

1.00

-

143-5TC

56C

23

120

2.28

752

14.53

2

F32

-

1.00

-

143-5TC

56C

23

104

1.97

871

16.84

2

F32

-

1.00

-

143-5TC

56C

23

103

2.44

881

17.02

2

F42

-

1.25

-

143-5TC

56C

25

89

1.68

1023

19.76

2

F32

-

1.00

-

143-5TC

56C

23

83

2.49

1091

21.08

2

F42

-

1.25

-

143-5TC

56C

25

74

1.41

1221

23.59

2

F32

-

1.00

-

143-5TC

56C

23

71

1.99

1281

24.75

2

F42

-

1.25

-

143-5TC

56C

25

68

1.30

1324

25.58

2

F32

-

1.00

-

143-5TC

56C

23

60

2.81

1513

29.23

2

F52

-

1.375

182-4TC

143-5TC

-

27

59

1.74

1528

29.54

2

F42

-

1.25

-

143-5TC

56C

25

57

2.71

1586

30.65

2

F52

-

1.375

182-4TC

143-5TC

-

27

54

1.03

1666

32.20

2

F32

-

1.00

-

143-5TC

56C

23

54

1.24

1684

32.55

2

F42

-

1.25

-

143-5TC

56C

25

53

1.74

1661

33.13

3

F43

-

1.25

-

143-5TC

56C

25

49

2.29

1851

35.78

2

F52

-

1.375

182-4TC

143-5TC

-

27

48

2.28

1885

36.43

2

-

F62

1.50

182-4TC

143-5TC

-

29

47

1.14

1878

37.47

3

F43

-

1.25

-

143-5TC

56C

25

45

1.96

1995

38.55

2

F52

-

1.375

182-4TC

143-5TC

-

27

44

2.22

1972

39.35

3

F53

-

1.375

-

143-5TC

56C

27

43

1.23

2086

40.32

2

F42

-

1.25

-

143-5TC

56C

25

42

2.45

2170

41.94

2

-

F62

1.50

182-4TC

143-5TC

-

29

40

2.55

2181

43.52

3

-

F63

1.50

-

143-5TC

56C

29

39

1.87

2293

44.32

2

F52

-

1.375

182-4TC

143-5TC

-

27

38

1.86

2303

45.93

3

F53

-

1.375

-

143-5TC

56C

27

36

0.96

2425

48.37

3

F43

-

1.25

-

143-5TC

56C

25

36

2.09

2536

49.02

2

-

F62

1.50

182-4TC

143-5TC

-

29

34

1.59

2677

51.74

2

F52

-

1.375

182-4TC

143-5TC

-

27

30

1.25

2988

57.75

2

-

F62

1.50

182-4TC

143-5TC

-

29

30

1.69

2932

58.49

3

-

F63

1.50

-

143-5TC

56C

29

29

0.96

3004

59.92

3

F43

-

1.25

-

143-5TC

56C

25

29

1.25

3158

61.03

2

F52

-

1.375

182-4TC

143-5TC

-

27

28

1.47

3103

61.89

3

F53

-

1.375

-

143-5TC

56C

27

26

1.25

3493

67.50

2

-

F62

1.50

182-4TC

143-5TC

-

29

26

1.66

3375

67.34

3

-

F63

1.50

-

143-5TC

56C

29

25

1.15

3687

71.25

2

F52

-

1.375

182-4TC

143-5TC

-

27

25

1.23

3567

71.16

3

F53

-

1.375

-

143-5TC

56C

27

22

1.43

3912

78.05

3

-

F63

1.50

-

143-5TC

56C

29

See How To Order on pages 18 - 19 www.renold.com 12

Input shaft bushing required - see page 41.


11/2 HP

NEMA Frame Selections 1750 RPM Input

Nr째 Red.

Output Shaft DIA

Cast Iron

Ratio

Aluminum

Two or Three Stages Two or Three Stages

Output Output Speed Service Torque (RPM) Factor (Ib-in)

Dim. on Page

Available Motor Flanges

21

1.06

4135

82.48

3

F53

-

1.375

-

143-5TC

56C

27

19

1.22

4592

91.61

3

-

F63

1.50

-

143-5TC

56C

29

18

0.90

4853

96.82

3

F53

-

1.375

-

143-5TC

56C

27

16

1.02

5481

109.35

3

-

F63

1.50

-

143-5TC

56C

29

Input shaft bushing required - see page 41.

See How To Order on pages 18 - 19

2 HP

NEMA Frame Selections 1750 RPM Input

Nr째 Red.

Output Shaft DIA

Cast Iron

Ratio

Aluminum

Two or Three Stages Two or Three Stages

Output Output Speed Service Torque (RPM) Factor (Ib-in)

Dim. on Page

Available Motor Flanges -

27

143-5TC

-

27

143-5TC

56C

23

266

5.49

453

6.57

2

F52

-

1.375

182-4TC

143-5TC

232

4.94

521

7.56

2

F52

-

1.375

182-4TC

218

2.63

554

8.03

2

F32

-

1.00

-

216

2.91

560

8.12

2

F42

-

1.25

-

143-5TC

56C

25

174

2.47

694

10.06

2

F42

-

1.25

-

143-5TC

56C

25

168

2.21

717

10.40

2

F32

-

1.00

-

143-5TC

56C

23

123

3.67

983

14.24

2

F52

-

1.375

182-4TC

143-5TC

-

27

120

1.71

1002

14.53

2

F32

-

1.00

-

143-5TC

56C

23

104

1.48

1162

16.84

2

F32

-

1.00

-

143-5TC

56C

23

103

1.83

1174

17.02

2

F42

-

1.25

-

143-5TC

56C

25

96

1.78

1255

18.19

2

F42

-

1.25

-

143-5TC

56C

25

91

3.23

1328

19.25

2

F52

-

1.375

182-4TC

143-5TC

-

27

89

1.26

1364

19.76

2

F32

-

1.00

-

143-5TC

56C

23

85

3.42

1420

20.58

2

-

F62

1.50

182-4TC

143-5TC

-

29

83

1.87

1455

21.08

2

F42

-

1.25

-

143-5TC

56C

25

80

2.89

1503

21.78

2

F52

-

1.375

182-4TC

143-5TC

-

27

78

2.74

1551

22.48

2

F52

-

1.375

182-4TC

143-5TC

-

27

74

1.05

1628

23.59

2

F32

-

1.00

-

143-5TC

56C

23

71

1.49

1707

24.75

2

F42

-

1.25

-

143-5TC

56C

25

70

2.48

1727

25.04

2

F52

-

1.375

182-4TC

143-5TC

-

27

68

0.97

1765

25.58

2

F32

-

1.00

-

143-5TC

56C

23

63

2.77

1911

27.69

2

-

F62

1.50

182-4TC

143-5TC

-

29

60

2.11

2017

29.23

2

F52

-

1.375

182-4TC

143-5TC

-

27

60

2.49

2001

29.00

2

-

F62

1.50

182-4TC

143-5TC

-

29

59

1.31

2038

29.54

2

F42

-

1.25

-

143-5TC

56C

25

57

2.03

2114

30.65

2

F52

-

1.375

-

143-5TC

56C

27

54

0.93

2246

32.55

2

F42

-

1.25

-

143-5TC

56C

25

53

1.31

2214

33.13

3

F43

-

1.25

-

143-5TC

56C

25

52

2.27

2339

33.90

2

-

F62

1.50

182-4TC

143-5TC

-

29

49

1.72

2469

35.78

2

F52

-

1.375

182-4TC

143-5TC

-

27

See How To Order on pages 18 - 19 www.renold.com 13

Input shaft bushing required - see page 41.


2 HP

NEMA Frame Selections 1750 RPM Input

Nr째 Red.

Output Shaft DIA

Cast Iron

Ratio

Aluminum

Two or Three Stages Two or Three Stages

Output Output Speed Service Torque (RPM) Factor (Ib-in)

Dim. on Page

Available Motor Flanges

48

1.71

2513

36.43

2

-

F62

1.50

182-4TC

143-5TC

-

29

47

2.25

2488

37.23

3

-

F63

1.50

-

143-5TC

56C

29

45

1.47

2660

38.55

2

F52

-

1.375

182-4TC

143-5TC

-

27

44

1.66

2630

39.35

3

F53

-

1.375

-

143-5TC

56C

27

43

0.93

2782

40.32

2

F42

-

1.25

-

143-5TC

56C

25

42

1.84

2893

41.94

2

-

F62

1.50

182-4TC

143-5TC

-

29

40

1.91

2909

43.52

3

-

F63

1.50

-

143-5TC

56C

29

39

1.40

3058

44.32

2

F52

-

1.375

182-4TC

143-5TC

-

27

38

1.40

3070

45.93

3

F53

-

1.375

-

143-5TC

56C

27

36

1.57

3382

49.02

2

-

F62

1.50

182-4TC

143-5TC

-

29

34

1.19

3570

51.74

2

F52

-

1.375

182-4TC

143-5TC

-

27

30

0.93

3984

57.75

2

-

F62

1.50

182-4TC

143-5TC

-

29

30

1.26

3910

58.49

3

-

F63

1.50

-

143-5TC

56C

29

29

0.93

4211

61.03

2

F52

-

1.375

182-4TC

143-5TC

-

27

28

1.10

4137

61.89

3

F53

-

1.375

-

143-5TC

56C

27

26

0.93

4657

67.50

2

-

F62

1.50

182-4TC

143-5TC

-

29

26

1.24

4501

67.34

3

-

F63

1.50

-

143-5TC

56C

29

25

0.92

4756

71.16

3

F53

-

1.375

-

143-5TC

56C

27

22

1.07

5216

78.05

3

-

F63

1.50

-

143-5TC

56C

29

19

0.91

6123

91.61

3

-

F63

1.50

-

143-5TC

56C

29

Input shaft bushing required - see page 41.

See How To Order on pages 18 - 19

3 HP

NEMA Frame Selections 1750 RPM Input

Nr째 Red.

Output Shaft DIA

Cast Iron

Ratio

Aluminum

Two or Three Stages Two or Three Stages

Output Output Speed Service Torque (RPM) Factor (Ib-in)

Dim. on Page

Available Motor Flanges

266

3.66

680

6.57

2

F52

-

1.375

182-4TC

143-5TC

-

27

232

3.29

782

7.56

2

F52

-

1.375

182-4TC

143-5TC

-

27

218

1.76

831

8.03

2

F32

-

1.00

-

143-5TC

56C

23

216

1.94

840

8.12

2

F42

-

1.25

-

143-5TC

56C

25

198

3.57

913

8.82

2

F52

-

1.375

182-4TC

143-5TC

-

27

174

1.65

1041

10.06

2

F42

-

1.25

-

143-5TC

56C

25

168

1.48

1076

10.40

2

F32

-

1.00

-

143-5TC

56C

23

141

2.68

1282

12.39

2

F52

-

1.375

182-4TC

143-5TC

-

27

123

2.45

1474

14.24

2

F52

-

1.375

182-4TC

143-5TC

-

27

120

1.14

1503

14.53

2

F32

-

1.00

-

143-5TC

56C

23

105

2.47

1721

16.63

2

F52

-

1.375

182-4TC

143-5TC

-

27

104

0.99

1742

16.84

2

F32

-

1.00

-

143-5TC

56C

23

103

1.22

1761

17.02

2

F42

-

1.25

-

143-5TC

56C

25

96

1.19

1882

18.19

2

F42

-

1.25

-

143-5TC

56C

25

See How To Order on pages 18 - 19 www.renold.com 14

Input shaft bushing required - see page 41.


3 HP

NEMA Frame Selections 1750 RPM Input

Nr째 Red.

Output Shaft DIA

Cast Iron

Ratio

Aluminum

Two or Three Stages Two or Three Stages

Output Output Speed Service Torque (RPM) Factor (Ib-in)

Dim. on Page

Available Motor Flanges

91

2.15

1993

19.25

2

F52

-

1.375

182-4TC

143-5TC

-

27

85

2.28

2130

20.58

2

F62

F62

1.50

182-4TC

143-5TC

-

29

83

1.24

2182

21.08

2

F42

1.25

-

143-5TC

56C

25

82

2.40

2204

21.29

2

F62

1.50

182-4TC

143-5TC

-

29

80

1.92

2254

21.78

2

F52

1.375

182-4TC

143-5TC

-

27

78

1.83

2326

22.48

2

F52

1.375

182-4TC

143-5TC

-

27

74

2.17

2452

23.69

2

F62

1.50

182-4TC

143-5TC

-

29

71

1.00

2561

24.75

2

F42

1.25

-

143-5TC

56C

25

70

1.66

2591

25.04

2

F52

1.375

182-4TC

143-5TC

-

27

63

1.85

2866

27.69

2

F62

1.50

182-4TC

143-5TC

-

29

60

1.40

3025

29.23

2

F52

1.375

182-4TC

143-5TC

-

27

60

1.66

3001

29.00

2

F62

1.50

182-4TC

143-5TC

-

29

57

1.35

3172

30.65

2

F52

1.375

182-4TC

143-5TC

-

27

51

1.51

3508

33.90

2

F62

1.50

182-4TC

143-5TC

-

29

49

1.15

3703

35.78

2

F52

1.375

182-4TC

143-5TC

-

27

48

1.14

3770

36.43

2

F62

F62

1.50

182-4TC

143-5TC

-

29

47

1.50

3733

37.23

3

F63

F63

1.50

-

143-5TC

56C

29

45

0.98

3989

38.55

2

F52

1.375

182-4TC

143-5TC

-

27

45

0.93

4605

45.93

3

F53

1.375

-

143-5TC

56C

27

42

1.23

4340

41.94

2

F62

F62

1.50

182-4TC

143-5TC

-

29

40

1.28

4363

43.52

3

F63

F63

1.50

-

143-5TC

56C

29

39

0.94

4587

44.32

2

F52

1.375

182-4TC

143-5TC

-

27

38

1.11

3945

39.35

3

F53

1.375

-

143-5TC

56C

27

36

1.04

5073

49.02

2

F62

1.50

182-4TC

143-5TC

-

29

F62

F62

F62 F62 F62

F62

Input shaft bushing required - see page 41.

See How To Order on pages 18 - 19

5 HP

NEMA Frame Selections 1750 RPM Input

Nr째 Red.

Output Shaft DIA

Cast Iron

Ratio

Aluminum

Two or Three Stages Two or Three Stages

Output Output Speed Service Torque (RPM) Factor (Ib-in)

Dim. on Page

Available Motor Flanges

282

2.56

1071

6.21

2

-

F62

1.50

182-4TC

143-5TC

-

29

266

2.20

1134

6.57

2

F52

-

1.375

182-4TC

143-5TC

-

27

245

2.57

1233

7.15

2

-

F62

1.50

182-4TC

143-5TC

-

29

232

1.98

1303

7.56

2

F52

-

1.375

182-4TC

143-5TC

-

27

209

2.57

1441

8.36

2

-

F62

1.50

182-4TC

143-5TC

-

29

198

2.14

1522

8.82

2

F52

-

1.375

182-4TC

143-5TC

-

27

150

2.49

2019

11.71

2

-

F62

1.50

182-4TC

143-5TC

-

29

141

1.61

2136

12.39

2

F52

-

1.375

182-4TC

143-5TC

-

27

130

2.29

2324

13.48

2

-

F62

1.50

182-4TC

143-5TC

-

29

123

1.47

2456

14.24

2

F52

-

1.375

182-4TC

143-5TC

-

27

See How To Order on pages 18 - 19 www.renold.com 15

Input shaft bushing required - see page 41.


5 HP

NEMA Frame Selections 1750 RPM Input

Nr째 Red.

Output Shaft DIA

Cast Iron

Ratio

Aluminum

Two or Three Stages Two or Three Stages

Output Output Speed Service Torque (RPM) Factor (Ib-in)

Dim. on Page

Available Motor Flanges

111

1.95

2717

15.75

2

-

F62

1.50

182-4TC

143-5TC

-

29

105

1.48

2868

16.63

2

F52

-

1.375

182-4TC

143-5TC

-

27

96

1.69

3142

18.22

2

-

F62

1.50

182-4TC

143-5TC

-

29

91

1.29

3321

19.25

2

F52

-

1.375

182-4TC

143-5TC

-

27

85

1.37

3550

20.58

2

-

F62

1.50

182-4TC

143-5TC

-

29

82

1.44

3673

21.29

2

-

F62

1.50

182-4TC

143-5TC

-

29

80

1.15

3756

21.78

2

F52

-

1.375

182-4TC

143-5TC

-

27

78

1.10

3877

22.48

2

F52

-

1.375

182-4TC

143-5TC

-

27

74

1.30

4087

23.69

2

-

F62

70

0.99

4319

25.04

2

F52

63

1.11

4776

27.69

2

-

60

1.00

5002

29.00

2

-

52

0.91

5847

33.90

2

-

1.50

182-4TC

143-5TC

-

29

1.375

182-4TC

143-5TC

-

27

F62

1.50

182-4TC

143-5TC

-

29

F62

1.50

182-4TC

143-5TC

-

29

F62

1.50

182-4TC

143-5TC

-

29

See How To Order on pages 18 - 19

www.renold.com 16

Input shaft bushing required - see page 41.


71/2 HP

NEMA Frame Selections 1750 RPM Input

Nr째 Red.

Output Shaft DIA

Cast Iron

Ratio

Aluminum

Two or Three Stages Two or Three Stages

Output Output Speed Service Torque (RPM) Factor (Ib-in)

Dim. on Page

Available Motor Flanges

282

1.71

1607

6.21

2

-

F62

1.50

182-4TC

143-5TC

-

29

266

1.46

1700

6.57

2

F52

-

1.375

182-4TC

143-5TC

-

27

245

1.71

1850

7.15

2

-

F62

1.50

182-4TC

143-5TC

-

29

232

1.32

1955

7.56

2

F52

-

1.375

182-4TC

143-5TC

-

27

209

1.71

2162

8.36

2

-

F62

1.50

182-4TC

143-5TC

-

29

198

1.43

2282

8.82

2

F52

-

1.375

182-4TC

143-5TC

-

27

150

1.66

3029

11.71

2

-

F62

1.50

182-4TC

143-5TC

-

29

141

1.07

3205

12.39

2

F52

-

1.375

182-4TC

143-5TC

-

27

130

1.53

3486

13.48

2

-

F62

1.50

182-4TC

143-5TC

-

29

123

0.98

3684

14.24

2

F52

-

1.375

182-4TC

143-5TC

-

27

111

1.30

4075

15.75

2

-

F62

1.50

182-4TC

143-5TC

-

29

105

0.99

4301

16.63

2

F52

-

1.375

182-4TC

143-5TC

-

27

96

1.13

4714

18.22

2

-

F62

1.50

182-4TC

143-5TC

-

29

85

0.91

5325

20.58

2

-

F62

1.50

182-4TC

143-5TC

-

29

82

0.96

5509

21.29

2

-

F62

1.50

182-4TC

143-5TC

-

29

See How To Order on pages 18 - 19

www.renold.com 17

Input shaft bushing required - see page 41.


Aluminum and Cast Iron Sizes

How To: Typical Product Code

P F32A - F33A

1773 Lb.in.

Input Style

M Motorized

F42A - F43A

3014 Lb.in.

P Predisposed

F52A - F53A

4167 Lb.in.

R Type “ R ”

B F62C - F63C

5763 Lb.in.

www.renold.com 18

Modular Base


Order Typical Product Code

F32A

ST

Reducer Type

Mounting

Aluminum

C

Q

3

Ratio

Shaft

Output Shaft Diameter

Output Flange Diameter

See technical data table Pages 07-17

ST Standard

F32A

1.57

C

X

Input Mounting Position Flange NEMA Frame See tables Size Page 32

Hollow Output Shaft Ø

Ø

F33A F42A Ø

F43A F52A F53A

S./B./L. On Request Special torque arm bores A

A Output Shaft

C

F32A - F33A 1=Dia 1”

N=Witout

F42A - F43A * 1=Dia 1” 2=Dia 1.25” F52A - F53A * 2=Dia 1.25” 3=Dia 1.375” F62C - F63C 4=Dia 1.50”

F32A - F33A F42A - F43A 2=Dia 6.30”

Cast Iron

Nema 56C

( 160 mm )

3=Dia 7.87”

X Nema143-5TC

( 200 mm )

F52A - F53A F62C - F63C 3=Dia 7.87” 4=Dia 9.84”

F63C

( 250 mm )

D

RX Shrink Disk

See code in the chart of the dimensions

F32/3 Standard Dimension Code S1

W

Y Nema 182-4TC

( 200 mm )

B

F62C

Flange

F27

A

B

ØC

25

140

14

F42A - F43A 5=Dia 1” F52A - F53A 6=Dia 1.25”

F32/3 On Request Code

A

B

S2

F37

31.5

158

B1

F10

35

B2

F20

40

N1

N0182

20

N2

N0282

28

D1

db.F04

L1

GFL04

F62C - F63C 7=Dia 1.50”

ØC

S

LX Shrink Disk Ø

See page 37

-F

F32A - F33A P=Dia 25mm

Output Flange Mounted

F42A - F43A Q=Dia 30mm

I Stainless

F52C - F53C R=Dia 35mm

steel hub F62C - F63C on request T=Dia 40mm * Standard www.renold.com 19

V6

M Without NEMA Flange


Selection By Size / Torque and Speed For example:

Step 1 Find the TORQUE / SIZE F32A

Be sure to consider Service Factor.

Lb.in. 1773

Output shaft Diameter 1”

1.0 Service Factor Aluminum Case Output Speed (RPM)

Output Torque (Ib-in)

Input HP

218

1459

5.25

168

1588

120

1717

Ratio

1750 RPM Input

Output Shaft ( ” )

Available Motor Flanges

Reduction bushing

Standard

Optional

8.03

1

-

56C

143/5TC

-

4.42

10.40

1

-

56C

143/5TC

-

3.42

14.53

1

-

56C

143/5TC

-

Step 2 Select the OUTPUT SPEED, and the RATIO F32A

Lb.in. 1773

Output shaft Diameter 1”

1.0 Service Factor Aluminum Case Output Speed (RPM)

Output Torque (Ib-in)

Input HP

218

1459

5.25

168

1588

120

Ratio

1750 RPM Input

Output Shaft ( ” )

Available Motor Flanges

Reduction bushing

Standard

Optional

8.03

1

-

56C

143/5TC

-

4.42

10.40

1

-

56C

143/5TC

-

1717

3.42

14.53

1

-

56C

143/5TC

-

104

1717

2.95

16.84

1

-

56C

143/5TC

-

89

1717

2.51

19.76

1

-

56C

143/5TC

-

74

1717

2.10

23.59

1

-

56C

143/5TC

-

68

1717

1.94

25.58

1

-

56C

143/5TC

-

54

1717

1.54

32.20

1

-

56C

143/5TC

-

45

1459

1.08

39.05

1

-

56C

143/5TC

-

42

1717

1.19

41.68

1

-

56C

143/5TC

-

32

1717

0.91

54.39

1

-

56C

143/5TC

-

24

1631

0.66

71.82

1

-

56C

143/5TC

-

21

1459

0.51

83.04

1

-

56C

143/5TC

-

16

1459

0.38

109.66

1

-

56C

143/5TC

-

www.renold.com 20


Step 3 Select the SHAFT MOUNT or OUTPUT SHAFT or SHRINK DISK B

Shaft Mount

E G

0.98

F 0.63

ø0.55

1/4-20x0.62

øD

C

øD1

R

1.22

3.94

3.01

ø1.00

ø1.57

ø2.91 g6

ø1.57

0.20

A

0.25

9.55

4.27

5.51

R2

R1

1.12

0.12

0.79

0.08 0.81

Nr°4 M8x0.47

2.09

5.79

3.54

B2

C

Type 143/5TC 56C

F33A

F32A

Output Shaft

6.50 8.76

Shrink Disk

B2

C

Type 143/5TC 56C

6.50 9.18 Nr°3 M5x0.47 5.51

C 3.70

3/8-16x0.87

ø25 mm

ø1.57

ø25 mm

1.12

ø3.23

3.38

ø1.00

2.91

1.97

0.25

0.79

Nr°4 M8x0.51 B2

0.98 5.04

Type 143/5TC 56C

C

B3

6.50 7.27

F33A

Flange Mount

F32A

Or select an OUTPUT FLANGE C

Type 143/5TC 56C

B3

6.50 7.66

B3

0.49

1.56 0.98

C

0.49

5.79 Square

ø4.33

ø5.12

j6

Nr°4 ø0.33

0.14

0 .3 ø6 Flange Output Optional see page 37

0.79 4.72

4.33

Step 4 Go to page 18 - 19 to see how to order / options / etc. www.renold.com 21

Only for F33A


F32A

Lb.in. 1773

Output shaft Diameter 1.00”

1.0 Service Factor Aluminum Case Output Speed (RPM)

Output Torque (Ib-in)

Input HP

218

1459

5.25

168

1588

120

Ratio

1750 RPM Input

Output Shaft ( ” )

Available Motor Flanges

Standard

Optional

8.03

1.00

-

-

143/5TC

56C

4.42

10.40

1.00

-

-

143/5TC

56C

1717

3.42

14.53

1.00

-

-

143/5TC

56C

104

1717

2.95

16.84

1.00

-

-

143/5TC

56C

89

1717

2.51

19.76

1.00

-

-

143/5TC

56C

74

1717

2.10

23.59

1.00

-

-

143/5TC

56C

68

1717

1.94

25.58

1.00

-

-

143/5TC

56C

54

1717

1.54

32.20

1.00

-

-

143/5TC

56C

45

1459

1.08

39.05

1.00

-

-

143/5TC

56C

42

1717

1.19

41.68

1.00

-

-

143/5TC

56C

32

1717

0.91

54.39

1.00

-

-

143/5TC

56C

24

1631

0.66

71.82

1.00

-

-

143/5TC

56C

21

1459

0.51

83.04

1.00

-

-

143/5TC

56C

16

1459

0.38

109.66

1.00

-

-

143/5TC

56C

With Motor Shaft Reduction Bushing

F33A

Output shaft Diameter 1.00”

Lb.in. 1773

1.0 Service Factor Aluminum Case Output Speed (RPM)

Output Torque (Ib-in)

Input HP

17

1717

0.47

15

1717

12.6

Ratio

1750 RPM Input

Output Shaft ( ” )

Available Motor Flanges

Standard

Optional

106.07

1.00

-

-

-

56C

0.42

118.06

1.00

-

-

-

56C

1717

0.36

138.43

1.00

-

-

-

56C

12.4

1717

0.35

140.92

1.00

-

-

-

56C

9.6

1717

0.27

182.80

1.00

-

-

-

56C

9.1

1717

0.26

192.36

1.00

-

-

-

56C

6.8

1717

0.19

265.12

1.00

-

-

-

56C

5.2

1717

0.15

331.50

1.00

-

-

-

56C

4.8

1201

0.10

361.22

1.00

-

-

-

56C

3.5

1459

0.08

506.11

1.00

-

-

-

56C

www.renold.com 22


F32A

F33A Lbs. F32A 15.86

Shaft Mount C 6.50 6.50

ø D1

Type

Type R

0.625 0.875 F33A 0.625

øD

R

0.625 1.56 0.750 1.95 F33A 0.625 1.52

F32A

F32A

B

R2

E

F

G

3/16 3/16 3/16

0.71 0.84 0.71

7.54 7.94 7.73

1.57 1.97 1.57

5.97 5.97 6.16

F 0.63

ø0.55

1/4-20x0.63

A

1.22 0.20

3.94

ø1.00

ø2.91 g6

9.55

0.25

ø1.57

5.51

4.27

ø1.57

øD

C

øD1

R

Nr°4 M8x0.47

0.08

R2

R1

3.54

0.04 2.09

5.79

Available Reaction Arms Positions see page 36

3.54

F32A

Output Shaft

B2

C

Type 143/5TC 56C

F33A

0.81

Lbs. F33A 16.74

E G

0.98 0.12

R1

2.94

F32A 143/5TC 56C F33A

B A 10.46 6.50 10.46 6.91

1.12

Input Flange Type

6.50 8.94

Shrink Disk

B2

C

Type 143/5TC 56C

Nr°3 M5x0.47

6.50 9.18 5.51

C 3.70

ø25 mm

ø1.57

ø25 mm

1.12

ø3.23

3.39

ø1.00

1.97

2.91

3/8-16x0.87 0.25

0.79

Nr°4 M8x0.51 B2

Type 143/5TC 56C

C

B3

6.50 7.46

F33A

F32A

Flange Mount

Type 143/5TC 56C

C

B3

6.50 7.70 0.49

B3 1.48 0.98

C

0.49

5.79 Square

ø5.12

j6

Nr°4 ø0.33

ø4.33 0.14

0 .3 ø6 Flange Output Optional see page 37

0.79 4.74

0.98 5.04

4.33

www.renold.com 23

Only for F33A


F42A

Lb.in. 3014

Output shaft Diameter 1.00”

1.0 Service Factor Aluminum Case Output Speed (RPM)

Output Torque (Ib-in)

Input HP

216

1631

5.81

174

1717

103

Ratio

1750 RPM Input

Output Shaft ( ” )

Available Motor Flanges

Standard

Optional

8.12

1.00

-

-

143/5TC

56C

4.93

10.06

1.00

-

-

143/5TC

56C

2146

3.64

17.02

1.00

-

-

143/5TC

56C

96

2232

3.55

18.19

1.00

-

-

143/5TC

56C

83

2713

3.72

21.08

1.00

-

-

143/5TC

56C

71

2550

2.98

24.75

1.00

-

-

143/5TC

56C

59

2661

2.60

29.54

1.00

-

-

143/5TC

56C

54

2095

1.86

32.55

1.00

-

-

143/5TC

56C

43

2576

1.85

40.32

1.00

-

-

143/5TC

56C

41

1717

1.17

42.48

1.00

-

-

143/5TC

56C

33

2121

1.16

52.62

1.00

-

-

143/5TC

56C

25

1545

0.64

69.49

1.00

-

-

143/5TC

56C

With Motor Shaft Reduction Bushing

F43A

Output shaft Diameter 1.00”

Lb.in. 3014

1.0 Service Factor Aluminum Case Output Speed (RPM)

Output Torque (Ib-in)

Input HP

53

2893

2.52

47

2146

36

Ratio

1750 RPM Input

Output Shaft ( ” )

Available Motor Flanges

Standard

Optional

33.13

1.00

-

-

143/5TC

56C

1.66

37.47

1.00

-

-

143/5TC

56C

2335

1.40

48.37

1.00

-

-

143/5TC

56C

29

2893

1.40

59.92

1.00

-

-

143/5TC

56C

27

2335

1.03

65.81

1.00

-

-

143/5TC

56C

25

2893

1.20

69.45

1.00

-

-

143/5TC

56C

21

2893

1.03

81.52

1.00

-

-

143/5TC

56C

18

2893

0.86

97.30

1.00

-

-

143/5TC

56C

16

2335

0.63

107.22

1.00

-

-

-

56C

15

2661

0.67

114.22

1.00

-

-

-

56C

13

2661

0.56

136.33

1.00

-

-

-

56C

9.4

2661

0.41

186.09

1.00

-

-

-

56C

7.7

2893

0.37

228.89

1.00

-

-

-

56C

7.2

2661

0.32

242.87

1.00

-

-

-

56C

5.5

2661

0.24

320.70

1.00

-

-

-

56C

With Motor Shaft Reduction Bushing

www.renold.com 24


F42A

Shaft Mount Lbs. F42A 17.18

Lbs. F43A 18.06 Type R

Input Flange Type

F42A 143/5TC F43A 143/5TC 56C F43A

B A 11.03 6.88 11.03 7.28 11.03 7.11

C 6.50 6.50 6.50

Type

ø D1

øD

Ratio

0.625 8.12-69.49 0.750 33.13-97.30 0.625 107.22-320.70 0.625

F42A

0.625 0.875 F43A 0.625 F42A

F43A F43A

B 1.24

F43A

R

R1

R2

E

F

G

1.56 1.95 1.52 1.52

3/16 3/16 3/16 3/16

0.71 0.84 0.71 0.71

7.90 8.30 8.31 8.14

1.57 1.97 1.57 1.57

6.33 6.33 6.74 6.57

E G

ø0.55

0.63

F 1/4-20x0.63 R1

B2

F43A

F42A

C

From ratio 33.13-97.30

6.50 9.11

C

Type 143/5TC 56C

Shrink Disk

From ratio 107.22-320.70

B2

6.50 9.52

C

Type 143/5TC 56C

For bore angle see Page 37

6.22

Available Reaction Arms Positions see page 36

Output Shaft Type

A

1.22

2.24 3.94

143/5TC 56C

4.53

3.94

F43A

0.89

0.20

3.17

0.20 0.08

0.10

1.12

ø1.77

10.30

Nr°4 M8x0.55

0.25

ø1.00

6.22

R2

4.61

ø1.77

øD

C øD1 R

B2

Nr°3 M6x0.47

6.50 9.35 5.79

B2

C

ø3.70

2.26 1.97

1.11

ø30 mm

ø1.77

ø3.23

3.70

ø1.00

0.25

0.79

C

B3

6.50 7.80

C

Type 143/5TC 56C

B3

F43A

Type 143/5TC 56C

6.50 8.21

From ratio 33.13-97.30

B3

1.04

Nr°4 bore ø0.43 ø6.49

ø5.12

j6

5.79 Square

0.43

0.94

4.88 Flange Output Optional see page 37

5.30

www.renold.com 25

Type 143/5TC 56C

C

B3

6.50 8.04

From ratio 107.22-320.70

1.32

0.14

1.22 5.12

F43A

Flange Mount

F42A

Nr°5 M8x0.59


F52A

Lb.in. 4167

Output shaft Diameter 1.250”

1.0 Service Factor Aluminum Case Output Speed (RPM)

Output Torque (Ib-in)

Input HP

266 232 198 141 123 105 91 80 78 70 60 57 49 45 39 34 29 25

2490 2576 3262 3434 3606 4250 4293 4336 4250 4292 4250 4292 4247 3906 4291 4247 3932 4247

10.95 9.85 10.69 8.01 7.32 7.39 6.44 5.75 5.46 4.95 4.20 4.05 3.43 2.93 2.80 2.37 1.86 1.72

Ratio

6.57 7.56 8.82 12.39 14.24 16.63 19.25 21.78 22.48 25.04 29.23 30.65 35.78 38.55 44.32 51.74 61.03 71.25

1750 RPM Input

Output Shaft ( ” ) Standard

Optional

1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250

1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375

Available Motor Flanges

182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC

143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC

56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C

With Motor Shaft Reduction Bushing

F53A

Lb.in. 4167

Output shaft Diameter 1.250”

1.0 Service Factor Aluminum Case Output Speed (RPM)

Output Torque (Ib-in)

Input HP

44 38 28 25 21 18 15 13 11 9.7 9.5 8.5 7.3 6.4 5.5

4378 4293 4550 4378 4378 4378 4378 4550 4378 4550 4293 4378 4293 4378 4293

3.22 2.70 2.12 1.78 1.53 1.31 1.09 0.96 0.80 0.73 0.67 0.61 0.52 0.47 0.39

Ratio

39.35 45.93 61.89 71.16 82.48 96.82 115.56 137.20 157.74 179.06 184.15 205.87 240.34 271.85 317.36

1750 RPM Input

Output Shaft ( ” ) Standard

Optional

1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250

1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375

Available Motor Flanges

-

143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC

56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C

With Motor Shaft Reduction Bushing

www.renold.com 26


F52A

F53A

Shaft Mount Input Flange Type

F52A 143/5TC F52A 182/4TC F53A 143/5TC

B A 12.03 8.19 13.22 8.90 12.03 8.51

C 6.50 8.88 6.50

Type

ø D1

Type R

0.750 0.875 F53A 0.625

R

0.750 0.875 0.625 1.56 F53A 0.750 1.95

F52A

F52A

B

Lbs. F52A 29.07

R1

R2

E

F

G

3/16 1/4 3/16 3/16

0.84 0.96 0.71 0.84

9.66 9.66 9.54 9.94

1.97 1.97 1.57 1.97

7.69 7.69 7.97 7.97

Lbs. F53A 29.52

E

4.72 1.26

øD

G

ø0.55

0.63

F 1/4-20x0.63 R1

0.12

R2

5.71

1.69 0.20

3.48

0.20 4.72

0.10 2.44

4.72

Output Shaft F52A

Type

C

B2

143/5TC

6.50 11.08

182/4TC

8.88 11.79

F53A

1.22

A

0.25

1.37

ø1.97

Nr°4 M8x0.55

ø1.250

11.75

6.69

5.30

ø1.97

øD

C øD1 R

Type 143/5TC

C

For bore angle see Page 37

7.09

Available Reaction Arms Positions see page 36

Shrink Disk

B2

6.50 11.40

Nr°3 M6x0.59

6.69

B2

C

ø4.02

2.89 2.36

ø35 mm

ø1.97

1.37

ø3.62

4.02

ø1.250

0.25

0.79

1.91

143/5TC

C

B3

6.50 9.17

Type 182/4TC

C

B3

8.88 9.88

F53A

Type

F52A

F52A

Flange Mount

1.26 6.16

Nr°8 M8x0.59

Type 143/5TC

C

6.50 9.49

B3

1.10 Nr°4 bore ø0.43 on ø6.50

0.39

ø5.12

j6

ø7.87

0.14

0.98

7.48 Square

5.71 5.98

Flange Output Optional see page 37

www.renold.com 27

B3


F62C

Lb.in. 5763

Output shaft Diameter 1.500”

1.0 Service Factor Cast Iron Case Output Speed (RPM)

Output Torque (Ib-in)

Input HP

282 245 209 150 130 111 96 85 82 74 63 60 52 48 42 36 30 26

2747 3164 3698 5025 5322 5298 5322 4861 5298 5322 5298 4982 5298 4293 5322 5298 3721 4349

12.78 12.79 12.79 12.41 11.41 9.72 8.44 6.83 7.19 6.49 5.53 4.96 4.52 3.41 3.67 3.12 1.86 1.86

Ratio

6.21 7.15 8.36 11.71 13.48 15.75 18.22 20.58 21.29 23.69 27.69 29.00 33.90 36.43 41.94 49.02 57.75 67.50

1750 RPM Input

Output Shaft ( ” ) Standard

Optional

1.500 1.500 1.500 1.500 1.500 1.500 1.500 1.500 1.500 1.500 1.500 1.500 1.500 1.500 1.500 1.500 1.500 1.500

-

Available Motor Flanges

182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC 182/4TC

143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC

56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C

With Motor Shaft Reduction Bushing

F63C

Lb.in. 5763

Output shaft Diameter 1.500”

1.0 Service Factor Cast Iron Case Output Speed (RPM)

Output Torque (Ib-in)

Input HP

47 40 30 26 22 19 16 14 12 10.3 10 9 7.7 6.8 5.8

5598 5563 4945 5598 5598 5598 5598 4945 5598 4945 5563 5598 5563 5598 5563

4.34 3.69 2.44 2.40 2.07 1.77 1.48 1.10 1.08 0.84 0.92 0.83 0.71 0.63 0.53

Ratio

37.23 43.52 58.49 67.34 78.05 91.61 109.35 129.66 149.26 169.22 174.46 194.80 227.69 257.23 300.66

1750 RPM Input

Output Shaft ( ” ) Standard

Optional

1.500 1.500 1.500 1.500 1.500 1.500 1.500 1.500 1.500 1.500 1.500 1.500 1.500 1.500 1.500

-

Available Motor Flanges

-

143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC 143/5TC

56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C 56C

With Motor Shaft Reduction Bushing

www.renold.com 28


F62C

F63C

Shaft Mount Input Flange Type

F62C 143/5TC F62C 182/4TC F63C 143/5TC

B A 12.78 8.61 13.97 9.31 12.78 8.92

C 6.50 8.88 6.50

ø D1

Type

Type R

0.875 1.125 F63C 0.625

R

0.750 0.875 0.625 1.56 F63C 0.750 1.95

F62C

F62C

B 4.92 1.59

øD

R1

R2

E

F

G

3/16 1/4 3/16 3/16

0.84 0.96 0.71 0.84

9.66 9.66 9.54 9.94

1.97 1.97 1.57 1.97

7.69 7.69 7.97 7.97

Lbs. F62C 40.02 Lbs. F63C 48.46

E

ø0.55

G

0.79

F 1/4-20x0.63 R1

R2

A 2.17

6.69

3.82

4.92 4.92

2.28

Output Shaft F62C

Type

C

B2

143/5TC

6.50 11.95

182/4TC

8.88 12.65

F63C

0.12

0.20

0.20

0.12

1.32

1.67

ø2.17

12.87

Nr°4 M12x0.55

0.38

ø1.500

7.80

5.71

ø2.17

øD

C øD1 R

Type 143/5TC

C

B2

For bore angle see Page 37

7.48

Available Reaction Arms Positions see page 36

Shrink Disk

6.50 12.26

Nr°3 M8x0.67

7.20

B2

C

ø4.92

3.29 2.76

ø40 mm

ø2.17

1.51

ø4.02

4.92

ø1.375

0.31

0.79

143/5TC

C

B3

6.50 9.55

Type 182/4TC

C

B3

8.88 10.25

F63C

Type

F62C

F62C

Nr°7 M12x0.67

Flange Mount

1.26 6.63

C

Type 143/5TC

6.50 9.86

B3 2.41 1.04 Nr°4 bore ø0.53 on ø8.46

ø9.84

ø7.09

0.59

0.16

0.93 6.32

5.85

7.48 Square Flange Output Optional see page 37

www.renold.com 29

B3


FS20

Lb.in. 798

1.0 Service Factor Aluminum Case Output Speed (RPM)

Output Torque (Ib-in)

Input HP

29.1 16.1 13.9 11.8 9.9 7.3 5.6 4.2

534 966 1120 1314 1568 2141 2795 3690

0.34 0.16 0.16 0.16 0.16 0.16 0.16 0.16

1750 RPM Input

Output Shaft ( ” )

Ratio

Standard (mm)

Optional For Q.ty

20 20 20 20 20 20 20 20

0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750

60.2 108.9 126.3 148.2 176.9 241.5 315.2 416.2

Available Motor Flanges

-

-

56C 56C 56C 56C 56C 56C 56C 56C

4.43 0.98

4.14

0.63

0.20

ø14mm

11.38

9.27 ø1.12

0.90

0.24

9.27

M5x0.51

5.67

0.93

Ø20 2.56 3.11 3.15

3.15 4.92

N.4 M8x0.47

Output Flange Kit

Torque Arm Kit 0.55

ø3.74

5.51

0.43 0.16

ø0.35 4.53

0.43 0.83 1.10

3.11

Synthetic oil for all positions.

1.42

5.51

Oil Q.ty

Oz.

Mod. Base 16.91

Special Size www.renold.com 30

Weight Lbs. Mod. Base

9.47


FS50

Lb.in. 3990

1.0 Service Factor Aluminum Case Output Speed (RPM)

Output Torque (Ib-in)

Input HP

5.31 7.01 9.15 12.5 14.9 17.5 20.3 36.7

2950 3628 4205 3678 3004 4100 3581 4728

1.47 1.00 1.00 0.74 0.50 0.50 0.34 0.34

1750 RPM Input

Output Shaft ( ” )

Ratio

Standard (mm)

Optional For Q.ty

30 30 30 30 30 30 30 30

1.125 1.125 1.125 1.125 1.125 1.125 1.125 1.125

47.7 86.3 100.0 117.4 140.1 191.2 249.6 329.6

1.42

Available Motor Flanges

-

-

5.66

56C 56C 56C 56C 56C 56C 56C 56C Part. X

14 mm

0.71

0.20

0.20 1.97

7.48

7.68

14,08

12.05

7.48

0.47

1.30

0.31

ø30 mm

0.12

0.53

0.12

Nr.6 M8x0.59

3.94

4.80

5.67

6.54 Part. X 0.43

0.79 1.18

0.31

Weight Lbs. 1.31

ø30 mm

2.36

Mod. Base 25.33

2.44

Oil Q.ty

Oz.

Mod. Base 25.36 Synthetic oil for all positions.

Special Size www.renold.com 31


Lubrication F32/3A-F42/3A-F52/3A-F62/3C These Aluminum reducers are supplied complete with synthetic oil satisfactory for the life of the reducer in most applications. The quantity is suitable for mounting positions H3. If the reducer is mounted in a different position, the quantity of oil must be corrected using the chart below. Upon request reducers can be supplied from the factory with the proper oil fill for the other mounting positions noted below. With synthetic oil, no breather type drain is required.

LUBRICATED FOR LIFE WITH SYNTHETIC OIL. THIS REDUCER CAN BE OPERATED WITH ALL OIL PLUGS.

ATTENZIONE

Quality Oilseals

ATTENTION

Plug

Quality Oilseals

Bearings Suitable for All Positions

Bearing

H8

H3 Standard

H8

OIL QUANTITY ( Ounces )

H3 Standard

H6

H6

H7

V5

V6

H7

V5

V6

Position / Type

F32A

F33A

F42A

F43A

F52A

F53A

F62C

F63C

H3 Standard

11.53

13.29

17.56

28.15

21.09

38.73

22.78

40.42

H8 H6 H7

13.29

15.06

21.09

28.15

31.67

33.44

33.36

35.13

16.82

18.58

38.73

42.25

40.42

43.94

16.82

18.58

40.49

42.25

44.02

45.78

45.71

47.47

V5 V6

16.82

18.58

40.49

44.02

44.02

47.55

45.71

49.24

20.35

22.11

42.25

44.02

45.78

49.31

47.47

51.00

36.96

www.renold.com 32


Lubrication Start-Up - Verify that the installed mounting position is the same as the nametag mounting position. If not, adjust the oil quantity accordingly.

Lubricant - All Renold reducers are shipped from the factory properly filled with synthetic lubricant for H3 mounting position.

Maintenance & Oil Specifications - For synthetic oils, the lube should be changed every 20000 service hours or after four years. In case of extreme operating ( e.g. high humidity, aggressive environment or large temperature variations), shorter intervals between changes are recommended.

Typical Oils Viscosity ISO NLGI

Suggested Standard Oil

Type Shell

VG 460

CLP HC

-22°F

+176°F

VG 320

CLP HC

-31°F

+176°F

VG 220

PAO= Poly Alpha Olefin

CLP HC

-30°F

VG 150

CLP HC

-35°F

+50°F

VG 100

CLP HC

-35°F

+50°F

VG 68

CLP HC

-40°F

+50°F

VG 32

CLP HC

-40°F

+50°F

+176°F

Mobilgear SHC 634 Mobilgear SHC 632 Mobilgear SHC 630 Mobilgear SHC 629 Mobilgear SHC 629 Mobilgear SHC 626 Mobilgear SHC 624

TEXACO

Omala 460 HD Omala 320 HD Omala 220 HD Omala 150 HD Omala 150 HD

Klubersynth EG 4-460 Klubersynth EG 4-320 Klubersynth EG 4-220 Klubersynth EG 4-150 Klubersynth EG 4-150

N/A

N/A

N/A

Kluber-Summit HySyn FG-32

Ambient Temperature CLP HC Synthetic Hydrocarbons

Insolube EP 460 Insolube EP 460 Insolube EP 220 Insolube EP 150 Insolube EP 150 Insolube EP 68 N/A

Tribol 1510/460 Tribol 1510/320 Tribol 1510/220

N/A N/A

-

N/A

N/A

N/A

N/A

Pinnacle EP 220 Pinnacle EP 150 Pinnacle EP 150

N/A

N/A

-

N/A

N/A

Cetus PAO 46

N/A

Synthetic Lubricant Reducers can be operated without an open breather plug. If mineral oils are required an open breather plug is required.

Special Purpose Lubricants Ambient Temperature

Oil Type

Manufacturer

Oil Brand Name

20°F to 104°F ( -5°C to 40°C )

Food Grade Oil - Synthetic

Chevron

FM ISO 220

20°F to 104°F ( -5°C to 40°C )

Food Grade Oil - Synthetic

OilJAX

Magnaplate 85W140-FG

Mobil

Mobilux EP023

5°F to 125°F ( -20°C to 50°C )

Fluid Grease

-30°F to 140°F ( -35°C to 60°C )

Fluid Grease - Synthetic

Mobil

Mobilith SHC 007

-30°F to 140°F ( -35°C to 60°C )

Fluid Grease - Synthetic

Shell

Albida LC

www.renold.com 33


General Tecnical Information Overhung Loads and Thrust Load An overhung load exists when a force is applied at right angle to the shaft’s outermost bearing. Pulleys, sheaves and sprockets will cause an overhung load when used as a power take-off. The amount of overhung load will vary, depending on the type of power take-off used and its mounting location on the shaft. The catalog overhung load ratings listed below and in selection tables are calculated at the centerline of the shaft. Overhung load ratings are listed for each reducer size and should not be exceeded. If the basic reducer is selected using a service factor, that factor must also be used in the equations below. Output Shaft OHL = 126000 x Input HP x Overhung Load Factor x Efficiency Pitch Diameter ( Of sprocket, pulley or sheave ) x Output RPM Input Shaft OHL = 126000 x Input HP x Overhung Load Factor Pitch Diameter ( Of sprocket, pulley or sheave ) x Input RPM

OVERHUNG LOAD AT CENTER OF SHAFT EXTENSION

Overhung Loads Factors Sprocket 1.00 Gear Pinion 1.25 V-Belt Sheave or Pulley 1.50 Flat Belt 2.50

Torque and Horsepower Torque as it is related to gear reducers is defined as a twisting motion resulting in rotational movement. Horsepower is a measure of the rate of doing work, and depends on speed of rotation and the ratio. HP = TQ x Speed ( RPM ) 63025

TQ = HP x 63025 RPM

Service Factor A service factor is selected to adjust a reducer’s load carrying characteristics to reflect the application load requirements. Reducer Service Factor = Reducer HP Rating Motor HP Rating

Efficiency The efficiency of an inline helical speed reducer is dependent on input speed, quality of gearing, type of lubricant, ambient temperature and many other variables. The efficiency for a speed reducer can be easily calculated as follows. Efficiency = Output HP Input HP Average efficiency of Renold double reduction inline reducers: 96% triple reduction inline reducers: 93%

NOTE: The overhung load capacities in the catalogue are calculated at centerline of shaft extension with no thrust load www.renold.com 34


Radial and Axial Loads Output shaft

FR

Feq

FA

X

= =

F32/3A

F42/3A

F52/3A

F62/3C

RPM

FA [Lb]

FR [Lb]

FA [Lb]

FR [Lb]

FA [Lb]

FR [Lb]

FA [Lb]

FR [Lb]

200

269.6 300.0 316.8 350.9 367.3 450.0 471.8

86.3 95.9 101.3 112.3 117.5 144.0 151.0

431.4

94.4 104.7 124.5 127.6 132.6 158.6 215.7

471.8

187.4 210.5 222.4 252.7 266.9 321.3 321.3

936.7

140 120 85 70 40 15

53.9 60.0 63.4 70.1 73.5 90.1 94.4

Feq=

FR

2.21 X+1.19

FR

479.9 506.9 561.2 587.7 719.8 754.9 2.68 X+1.50

FR

523.0 622.8 533.8 663.2 792.6 1078.4 2.72 X+1.54

FR

1052.8 1112.1 1260.4 1334.6 1606.4 1606.4 2.81 X+1.63

If your application requires higher radial loads contact our technical office, it is in practice often possible to apply higher loads.

Input shaft FR FA

F32/3A

F42/3A

F52/3A

F62/3C

RPM

FA [Lb]

FR [Lb]

FA [Lb]

FR [Lb]

FA [Lb]

FR [Lb]

FA [Lb]

FR [Lb]

1400

43.5 43.8 43.8

217.4 219.1

69.6 70.1 70.1

347.8 350.5

67.4 84.7 110.8

337.0 423.3

27.0 55.0 86.5

135.3 275.7

900 500

219.1

350.5

www.renold.com 35

554.1

432.5


Available Reaction Arms Positions D

ØC

A

31 30

U T

34 33

32

B

V

N

F32/3A Code ST

Sew F27

Standard Dimensions A 0.98

B 5.51

F32/3A Code S2 N1 N2 L1 B1 B2

Sew F37

Nord N0182

Nord N0282

Lenze GFL04

Bonfiglioli F10

Bonfiglioli F20

øC 0.55

D 0.39

N 0.20

F42/3A

See page 23

T 1.57

U 0.49

V

Code ST

0.79

On Request A 1.24

B 6.22

øC 0.55

D 0.39

N 0.20

T 1.57

U 0.49

V

Sew F47

Code S4

Sew

D1

David B.

0.79

N4

Nord

db.F04

1.26

6.69

0.43

0.47

0.10

1.57

0.49

0.79

Nord

1.10

6.22

0.43

0.47

0.10

1.18

0.43

0.79

1.34

6.50

0.43

0.47

0.10

1.18

0.43

0.79

1.34

6.50

0.43

0.47

0.10

1.18

0.43

0.79

0.89

5.04

0.49

0.47

0.10

1.18

0.43

0.79

1.14

6.10

0.55

0.47

0.10

1.18

0.43

0.79

1.38

5.51

0.43

0.47

0.10

1.18

0.43

0.79

1.57 B2 Bonfiglioli F20

6.30

0.43

0.47

0.10

1.18

0.43

0.79

6.18

0.41

0.47

0.10

1.57

0.49

0.79

0.49

0.79

N2

N0282

0.89

5.04

0.49

0.39

0.20

1.18

0.43

0.79

N3

N1282

1.38

5.51

0.43

0.39

0.20

1.18

0.43

0.79

N4

N1382

1.18

0.43

0.79

Standard Dimensions

L1

A

B

øC

D

N

T

U

V

1.25

6.69

0.55

0.47

0.12

1.57

0.49

0.79

A

B

T

U

V

0.43

0.47

0.12

1.57

0.49

0.79

1.34

6.50

0.43

0.47

0.12

1.18

0.43

0.79

1.14

6.10

0.55

0.47

0.12

1.18

0.43

0.79

1.14

6.10

0.55

0.47

0.12

1.18

0.43

0.79

B3 Bonfiglioli 2.13 F30

6.69

0.51

0.47

0.12

1.57

0.49

0.79

1.44

6.18

0.41

0.47

0.12

1.57

0.49

0.79

2.09

7.28

0.55

0.47

0.12

1.57

0.49

0.79

F2

Flender Fd38

Flender Fd48

Lenze GFL04

Lenze GFL05

Bonfiglioli F10

Flender Fd38

ST

Sew F57

1.44

Standard Dimensions

Code

A

B

øC

D

N

T

U

V

7.80

0.47

0.47

0.12

1.57

0.49

0.79

A

B

øC

D

N

T

U

V

8.58

0.47

0.47

0.12

1.57

0.49

0.79

8.31

0.47

0.47

0.12

1.57

0.49

0.79

6.10

0.47

0.47

0.12

1.18

0.43

0.79

7.68

0.47

0.47

0.12

1.57

0.49

0.79

6.69

0.47

0.47

0.12

1.57

0.49

0.79

8.58

0.47

0.47

0.12

1.57

0.49

0.79

7.28

0.47

0.47

0.12

1.57

0.49

0.79

On Request

D2 David B. 1.61 db.F06 N5 Nord 1.50 N2282 L2 Lenze 1.14 GFL05 L3 Lenze 1.38 GFL06 B3 Bonfiglioli 2.13 F30 B4 Bonfiglioli 2.22 F40 F2 Flender 2.09 Fd48

www.renold.com 36

See page 29

1.59

F62/3C N

6.69

F1

Nord

Code

On Request

1.26

Lenze

Nord

F62/3C

See page 27

0.79

GFL05

F47

David B.

1.57

0.20

On Request V

0.20

0.49

L2

0.79

0.79

0.39

1.57

GFL04

0.49

U

0.43

0.12

L1

1.57

0.49

6.22

0.47

Lenze

0.10

T

1.10

0.55

N1382

0.47

1.57

D1

7.80

db.F04

0.55

N

0.79

1.59

F57

6.22

0.10

0.49

D

1.24

D

1.57

øC

V

0.47

0.20

F52/3A

U

øC

F1

Code

T

0.55

0.39

0.39

N

B

0.43

0.43

D

6.69

4.72

6.30

øC

A

Sew

0.79

1.57

B

1.26

Code S3

B1

ST

F37

See page 25

A

F42/3A

L2

F52/3A

Sew

Standard Dimensions


Available Output Flanges Single Output Shaft

Double Output Shaft

D

D

F

F

E

E

U

Q

T

Q

Q

J

H

J

H

L

Type øM øA g6

C

D

E

F

ø0.98

0.31

1.10

1.56

0.39

0.98

ø1.18

0.31

1.30

1.95

ø1.38

0.39

1.50

1.95

F62C ø7.87 ø1.57 F63C ø9.84

0.47

1.69

2.75

ø6.30

F42A F43A

ø6.30

F52A F53A

ø7.87

ø7.87

ø7.87

ø9.84

øN P

S Z

B

F32A F33A

C

R

øM

B

øA g6

j6

øG

C

j6

øG

øA g6

R

øA g6

B

B

C

Nr°4 øO

0.39 0.43 0.39 0.59

øG j6

1.04

1.10

ø4.33 ø5.12 ø4.33 ø5.12

H

J

L

0.14

0.79

6.28

0.14

0.94

7.22

0.98

8.55

0.93

9.07

ø5.12

0.14

ø7.09

0.16

0.39

0.65

ø5.12

0.14

0.59

0.45

ø7.09

0.16

N

O

P

ø5.12 ø0.33

5.79

ø6.50 ø0.43

5.79

ø5.12 ø0.33

5.79

ø6.50 ø0.43

5.79

ø6.30 ø0.43

7.48

ø7.87 ø0.53

7.48

ø6.30 ø0.43

7.48

ø7.87 ø0.53

7.48

Q

R

S

T

U

Z

M8x0.79

2.05

2.03

1.94

1.51

7.87

M10x0.91

2.36

2.99

2.85

2.57

9.74

M10x0.91

2.36

3.58

3.38

2.91

11.10

M12x1.26

3.15

3.80

3.56

2.90

12.28

Output Flange Standard

Face Mounting Dimensions

F42/3A

F52/3A 45°

78°

F62/3C

45°

47°

47°

78° 45°

12°

45°

43°

43°

12° 35°

65°

35°

60°

60°

65° 50° 3.70

Nr° 5 M8x0.59

Nr° 8 M8x0.59

110° 4.02

60° 4.92

www.renold.com 37

Nr° 7 M12x0.67


Oil Levels Plugs for F32A - F63C For applications requiring mineral oils, gearboxes can be delivered with oil plugs ( level and leak ) as represented in figure, for the oil quantity, see on pages 45 - 46 Breather Plug

0

1

2

3

Open With Valve

4

Oil Level Drain Plug A Positions H3 / H5

B

D

C

H3 Standard

H8

H3 Standard

H8

H6

H6

H8

H6

H7

V5

V6

A

2 (3)

1

0

4

0

1

B

0

1

1

2 (3)

2 (3)

1

C

1

4

2 (3)

1

1

1

D

1

2 (3)

1

1

1

5+2(3)+4

H7

V5

V6

H7

V5

V6

IEC Metric Motor Input Flanges L

Input Bore / Flange for IEC Motors ( Metric )

for Nema

Motor Flange

ø2

ø1

BORE

90 B5 100/112 B5

100/112 B14

IEC Flange

63 B5

71 B5

80 B5

ø 1 ( ’’ )

5.51

6.30

7.87

7.87

9.84

3.15

3.54

4.13

4.72

5.51

6.30

ø 2 ( ’’ )

0.43

0.55

0.75

0.94

1.10

0.35

0.43

0.55

0.75

0.94

1.10

Type

63 B5

71 B5

80 B5

90 B5

100/112 B5

56 B14

63 B14

71 B14

80 B14

90 B14

100/112 B14

56 B14 63 B14 71 B14 80 B14 90 B14

F32A F33A F42A F43A F52A F53A F62C F63C

www.renold.com 38


Accessories and Optionals Double Oil Seal Kit for Output Shaft

Special Output Shaft Bearings

181 B

176 175 173 171

181 A

F32/3A 171

F42/3A

F52/3A

F62/3C

O Ring O Ring O Ring O Ring 63.17x2.62 68.26x3.53 73.03x3.53 89.69x5.34 181A 181B

173 F30.0.271 F40.0.271 F50.0.271 F60.0.271 175 176

Oil Seal 40/52/7

Oil Seal 45/60/7

Oil Seal 50/65/8

F32/3A

F42/3A

F52/3A

F62/3C

32008

32009

32010

30211

Oil Seal 55/80/8

Standard Protection Cups

Protection Cups for Shrink Disk

192

195 193

F32/3A

F42/3A

F52/3A

196

F62/3C

F32/3A

F42/3A

F52/3A

F62/3C

192 F30.9.209 F30.9.209 F50.9.209 F60.9.209

195 F40.9.210 F40.9.210 F50.0.210 F60.0.210

193

196

T.C.E.I. M6x10 T.C.E.I. M6x10 T.C.E.I. M6x10 T.C.E.I. M8x12

www.renold.com 39

T.C.E.I. M6x10 T.C.E.I. M6x10 T.C.E.I. M6x10 T.C.E.I. M8x12


Optional Accessories & Modifications.

BRU56143

143/5TC

182/4TC

BRU143182

56C

182/4TC

BRU56182

Metric Output Shaft For Type

Diameter (mm)

F32A / F33A

25 | 20 | 30

F42A / F43A

30 | 25 | 35

F52A / F53A

35 | 30 | 40

For Type

Diameter (mm)

F62C / F63C

D

40 |35

www.renold.com 40

1 1/8

143/5TC

1 1/8

56C

7/ 8

Code

5/ 8

Type

7/8

5/8

Input Shaft Bushings for Nema Electric Motors


Technical Information Gears

Bearings

Oil seals

Shafts

Housings Gaskets

Screws

OUTPUT

Q.ty Oil seals

High resistance Zinc-plated Class 8.8

Mat. : C40 Method of calculation: AISI / AGMA 2001-B88Gears Tolerance DIN 3967

Mat.: 16 Mn Cr5 DIN: 16Mn Cr5 AISI/SAE (5115) Core and surface hardening Surface hardness: 58/60 HRC Surface hardness dept 0.3 / 0.5 mm MACHINING Precision class: DIN 6/7 First pinion ground Excluded Z7-Z9 First wheel Ground

Input shaft CORTECO / CORCOS from Freudenberg (Germany) 70 Shore

Open type Or sealed

INPUT

Mat.: 39NiCrMo3 DIN: 36NiCrMo4 AISI/SAE: 9840

2RS For vertical mounting.

Hydro-Mec graphite gasket On the housing

NITRILE OUTPUT Oil seals Output shaft SIDAT / N.O.K. (JAPAN) 72 Shore

ALUMINIUM: GD-Al Si12 Cu2 Fe DIN 226A SAE 384.2/383

AREXONS S6A4P on the first pinion;

CAST IRON: G20 UNI-ISO 185 DIN 1691 ASTM A159-70

On request VITON seals for high temperature.

Slow pinion normal Slow wheel Grounded

Maintenance Check List Maintain lubricant in good condition and at proper level. Apply proper maintenance to attached equipment at prescribed intervals recommended by the manufacturer.

Oil change after 20,000 hr. ( if synthetic ) Oil change after 10,000 hr. ( if mineral ) Oil seals inspect change 5,000 hr. Screws check after 2,000 hr. ( for Motor Flange ) Shafts bearings play 3,000 hr. Dispose of used lubricant in accordance with applicable laws and regulations. Operate the equipment as it was designed to be operated. Do not overload. Run at correct speed. Our company will not be responsible for any direct or indirect damages, caused by improper application or for not observing the catalog specifications. www.renold.com 41


Selection Check List Written authorization from Renold is required to operate or use reducers in lifts or people moving devices. Check to make certain application does not exceed the allowable load capacities published in the current catalogue. Buyer shall be solely responsible for determining the adequacy of the product for any and all uses to which Buyer shall apply the product. The application by Buyer shall not be subject to any implied warranty of fitness for a particular purpose.

In case of high temperatures we advise to mount oil seal in VITON on the hub.

Specify with the order if a special low noise level is required.

Reducers are not to be considered fail safe or self-Iocking devices. If these features are required, a properly sized, independent holding device should be utilized. Reducers should not be used as a brake. Any brakes that are used in conjunction with a reducer must be sized or positioned in such a way so as to not subject the reducer to loads beyond the catalog rating.

2 poles can be used only for very intermittent applications only. Specify it in the order to select the most suitable ratios.

If the application subjects the reducer to shock loads and sudden stops it is advisable to use mechanical or eletronic torque limiting devices.

Do not change mounting positions without contacting Renold. Altering the mounting position may require special lubrication provisions which must be factory installed. When reducers are mounted in positions V5 or V6 and used in continuous duty applications, replace the upper bearing with a self lubricated style bearing, and we suggest double input seal for V6.

Installation Check List Do not change mounting positions without contacting Renold. Altering the positions may require special lubrication provisions which must be factory installed. When reducers are mounted in positions V5 or V6 and used in continuous duty applications, replace the upper bearing with a self lubricated style bearing, and we suggest double input seal for V6.

In applications where multiple starts, stops or reverses occur, it is advisable to use Loctite Code 270 or similar compounds on the fastening bolts of the output flange and feet.

When mounting a motor to reducers, the fastening bolts should not be tightened until both the reducer flange and motor face are in contact. When mounting is complete check by manually rotating the motor’s shaft to be sure the assembly turns freely.

Make sure that mounting of pulleys or pinions does not create overhung loads exceeding the capacity of the reducer.

www.renold.com 42


Installation Check List When mounting anything on the reducer’s shaft,protect the bearings from impact by using the appropriate pullers and threaded holes in the end of the reducer shaft.

Check shaft and coupling alignment.

When mounting items to the reducer shaft, appropriate anti-seize and oxidizer compounds should be used.

For safety, Buyer or User should provide protective guards over all shaft extensions and any moving apparatus mounted thereon. The User is responsible for checking all applicable safety codes in his area and providing suitable guards. Failure to do so may result in bodily injury and/or damage to equipment.

If the reducer is to painted, protect machined surfaces and oil seals from over-spray.

Test run the first unit to verify proper operation.

When installed outdoors, make sure protection is provided from atmospheric elements.

High speed motors, greater than 1800 rpm, can produce high operating temperatures within the reducer and should only be used for intermittent duty applications. Decrease the reducer’s lubricant levels and install a breather plug.

Make sure there is sufficient space between any obstructions and the motor’s air intake area to provide adequate cooling for the motor.

LOCK OUT POWER before any maintenance is performed. Make absolutely sure that no voltage is applied while work is being done on the gearbox.

For very heavy radial load, additional output shaft support may be required to prevent premature bearing failure or shaft breakage from bending fatigue.

The system of connected rotating parts must be free from critical speed, torsional or other type vibration, no matter how induced. The responsibility for this system analysis lies with the purchaser of the speed reducer.

www.renold.com 43


Spare Parts Lists For F52/3A - F62/3C Shaft Mount Key

F32A F42A F52A F62C

38 7

45

69

23

2 39

33

78 A 4

24 49 94

108

91

25

105 1

67

90

114

66

35 B

35 A

20

75

51

47

5 111

124 36

78 B

21 37

26

53 79 8 111 37 92 27 37

110 3 50 108

106

F33A F43A F53A F63C

46

41 B

24 90 29 41 A

108 48

24 90

35 B

25 35 A

23

33

80 A

11

51

12

112

114

66

43 A 28 42

112 43 B 95 30 42

www.renold.com 44

13

56

80 B


Spare Parts Lists F32A

F42A

F52A

F62C

35 / 47 / 7

35 / 47 / 7

45 / 62 / 7

45 / 62 / 7

20 / 30 / 7

20 / 30 / 7

20 / 30 / 7

25 / 35 / 7

40 / 68 / 8

45 / 75 / 8

50 / 80 / 7

55 / 100 / 8

40 / 55 / 7

45 / 62 / 7

50 / 65 / 7

55 / 80 / 8

Oil Seal Flange 3 stage

35 / 47 / 7 25 / 40 / 7

35 / 47 / 7 25 / 40 / 7

35 / 47 / 7

35 / 47 / 7

Oil Seal Type R 3 stage

20 / 30 / 7 25 / 40 / 7

20 / 30 / 7 25 / 40 / 7

20 / 30 / 7

20 / 30 / 7

F30.0.301

F40.0.301

F50.0.301

F60.0301

022.0.302

022.0.302

23.00.302

23.00.302

022.0.302 050.0.301

022.0.302 050.0.301

022.0.302

022.0.302

F30.0.300

F30.0.300

F50.0.300

F50.0.300

6202

6202

6302

6204

6202

6202

6204

6304

6007

6007

6009

6009

6004

6004

6205

6205

6008

6009

6010

6211

6008

6009

6010

6211

6202

6202

6302

6204

6202

6202

6204

6304

Input Bearing 3 Stage

6004 6202

6004 6202

6004

6004

Bearing Input Shaft 3 Stage

6007 6005

6007 6005

6007

6007

Bearing Type R 3 Stage

6004 6005

6004 6005

6004

6004

Nr. 75 79 78 A

Oil seal 78 B 80 A 80 B

110 111

Gasket 112 114

35A 35B 36 37 38

Bearings

39 41A 41B 42 43A 43B

Oil Seal Flange 2 stage

Oil Seal Type R 2 stage

Output Oil Seal

Output Oil Seal

Gasket Close Cover

Gasket Cover 2 stage

Gasket Cover 3 stage

Gasket Housing / Cover

Bearing

Bearing

Bearing Input Shaft 2 Stage

Input Bearing

Bearing Output Hub

Bearing Output Hub

Bearing

Bearing

www.renold.com 45


Nema Standard Motor Dimensions Reference AH N

W

S

U AK BD

TAP

d

45째

45째

N-W

AJ

NEMA SHAFT AND KEYWAY DIMENSIONS ( Inches ) NEMA SHAFT (U)

KEYWAY DIMENSIONS (Wxd) (S)

5/ 8

3/ x 3/ 16 32

7/ 8

3/ x 3/ 16 32

1 1 /8 3 1 /8 5 1 /8

1/ x 1/ 4 8

0.709 0.964 1.241 1.518 1.796

5/ x 5/ 16 32 3/ x 3/ 8 16

The condensed dimensions shown on these pages are for general reference only and are not for construction. Certified drawings of all rating are available for construction purposes.

NEMA DIMENSIONS ( Inches ) Nema Frame S56 56 143T 145T 182T 184T

U

N 15/ 16

1

5/

3 2 /8

7/

2

7/

8

1

N-W

8

1

8

2

1/

8

2

7/ 8 1/ 4

3/ 4

AH 2 2 2

AJ

1/ 16 1/ 8

5 5

5/ 8

7

7/ 8 7/ 8

1/ 4

www.renold.com 46

AK 4 4 8

1/ 2 1/ 2

1/ 2

BD 6 6 8

TAP

KEY

1/ 2

3/ -16 8

1/ 2

3/ -16 8

3/ 16

7/ 8

1/ 2 -13

1/ 4

3/ 16


Notes

www.renold.com 47


Notes

www.renold.com 48


Notes

www.renold.com 49


Worldwide Sales and Services ARGENTINA

BANGLADESH

DENMARK

INDIA

Bennett Anderson, Gonzales Y Cia SA, J.Aguero 1817 (1605) Munro Buenos Aires Tel: + 54 11 4761 5007/ 3531 Fax: + 54 11 4760 0866

Brady & Co (Bangladesh) Ltd, 31, Bangabandhu Avenue, Dhaka-1000 Tel: + 880 2802358 Fax: + 880 2802358

Renold A/S, Skelmarksvej 6, Postboks 90, 2605 Brøndby. Tel: +45 43 452611 Fax: +45 43 456592 Email: renold@post9.tele.dk

Los Ases Ketten SA, Avda Gaona 4046, 1407 Buenos Aires Tel: + 54 116710855 Fax: + 54 116713141

BELGIUM

EGYPT

Renold Continental Ltd Allée Verte 1,1000 Brussel. Tel: +32 (0) 2 2011262 Fax: +32 (0) 2 2032210 Email: info@renold.be

Itaco, Int’l for Trading & Agency, P.O. Box 7550, Nasr City, Cairo. Tel: + 20 2 2718036 Fax: + 20 2 2878089

Voltas Limited., Machine Tool Division, Voltas House B, 3rd Floor, TB Kadam Marg, Chinchpokli, Mumbai 400033 Tel: 091 22 370 0829 Fax: 091 22 371 4889 Email: mshaik@voltasltd.com

Renold Australia Proprietary Ltd 508-520 Wellington Road, Mulgrave, Victoria 3170, Mulgrave North Tel: +61 (0) 3 9262 3333 Fax: +61 (0) 3 9561 8561 Branch Tel: +61 (0) 3 9262 3355 Email: melcag@renold.com.au

CANADA

EL SALVADOR

Renold Canada Ltd 121 Roy Boulevard, Brantford, Ontario, N3T 5N4 Toll Free: 1-800-265-9970 Tel: +1 519 756 6118 Fax: +1 519 756 1767 Email: inquiry@renoldcanada.com

MVA & Cia Residencial San Luis, Avenida 4 #45 Block 2, San Salvador, El-Salvador, Central America Tel: + 503 274 649

Unit 1, 12-18 Victoria Street, Lidcombe, Sydney, NSW 2141. Tel: +61 (0) 2 9649 3122 Fax: +61 (0) 2 9646 1295 Email: nswsales@renold.com.au

622 rue De Hull, Ville La Salle, Quebec, H8R 1V9. Toll Free: 1-800-361-1414 Tel: +1 514 367 1764 Fax: +1 514 367 4993

Kraftmek Oy, Hitsaajankatu 9, P.O. Box 36, FIN-00811 Helsinki Tel: + 358 9 7557355 Fax: + 358 9 7550414

Technica J. Bokstein Co. Ltd, 3 Hatrupa Street, Netanya 42504 Tel: + 972 9 8850505 Fax: + 972 36131074

Unit 10, 31 Boyland Avenue, Coopers Plains, Brisbane, Queensland 4108. Tel: +61 (0) 7 3275 2155 Fax: +61 (0) 7 3875 1779

CHILE

FRANCE

ITALY

Brampton Renold, Zone Industrielle A, Rue de la Pointe, BP 359, 59473 Seclin Cedex. Tel: +33 (0) 320 16 29 29 Fax: +33 (0) 320 16 29 00

Bianchi Cuscinetti SpA Via Zuretti, 102, 20125 Milano, Tel: + 39 02 67861 Fax: + 39 02 66981669

AUSTRALIA

Corner Orsmond & George Sts. Hindmarsh, Adelaide, South Australia 5007. Tel: +61 (0) 8 8346 9077 Fax: +61 (0) 8 8340 1217 Unit 2, 127 Grandstand Street, Belmont, Perth, West Australia 6104. Tel: +61 (0) 8 9479 1388 Fax: +61 (0) 8 9479 1364 Unit 13 56 Industrial Drive, Mayfield, NSW 2304 Tel: +61 (0) 2 4960 8440 Fax: +61 (0) 2 4960 8455 PO Box 159, Unanderra, Wollongong, NSW 2526. Tel: +61 (0) 2 42 621771 Fax: +61 (0) 2 42 621772 Shop B, 247 Ingham Road, Garbutt, Townsville, QLD 4814. Tel: +61 (0) 7 4779 5922 Fax: +61 (0) 7 4775 1446

AUSTRIA Renold GmbH Rudolf Hausner Gasse 60/1 A-1220 Wien Austria. Tel: +43 (0) 1 3303484 0 Fax: +43 (0) 1 3303484 5

FINLAND

Sargent S.A., Avda. Presidente Bulnes No 205, Casilla 166-D, Santiago - Chile. Tel: (56 2) 510 3000 Fax: (56 2) 698 3989 Email: secventas@sargentagricola.cl

GERMANY Arnold & Stolzenberg, Juliusmühle, D37574 Einbeck. Postal address: PO Box 1635 + 1645 D37557 Einbeck. Tel: +49 (0) 5562 81248 Fax: +49 (0) 5562 81130 Email: arnoldandstolzenberg @t-online.de

CHINA Renold Transmission (Shanghai) Company Limited Unit 4A, Block 15 69 XiYa Road Waigaoqiao Free Trade Zone Shanghai 200131 Tel: +86 21 5046 2696 Fax: +86 21 5046 2695 Email: sales@renold.cn

GREECE Provatas Engineering 53/47 Dragatsaniou St, 185 - 45 Piraeus. Tel: + 30 1 4170266 Fax + 30 1 4170253

COLOMBIA Transmission de Potencia SA Carrera 68B No10 - 98 Apartado Aereo 6794 Santafe de Bogato DC Tel: + 571 2600100 Fax: + 571 2904823

HOLLAND Renold Continental Ltd, Jarmuiden 30c, 1046 AD Amsterdam. Tel: +31 (0) 20 614 6661 Fax: +31 (0) 20 614 6391 Email: info@renold.nl

Importadora Casa Sueca Ltda., Calle 52, No. 1N-74, Apartado Aereo 1208, Cali. Tel: 00 57 2346 4455 Fax: 00 57 2346 4967

HUNGARY

CZECH REPUBLIC

Renold GesmbH Technical Office, Ing. Havasi Janos, Ret Utca 25, H-6200 Kiskörös. Tel: +36 (0) 78 312483 Fax: +36 (0) 78 312484

Renold GesmbH Technical Office, Dipl. Ing. R. Badura, Jaroslavice 129, CZ-76001 Zlin. Tel: +42 67 7211074 Fax: +42 67 7211074

www.renold.com 50

NORTHERN IRELAND Henry R. Ayton Ltd, Derriaghy, Dunmurry, Belfast. Tel: 01232 618511 Fax: 01232 602436

SOUTHERN IRELAND Henry R. Ayton Ltd., Broomhill Drive, Tallagh, Dublin 24 Tel: + 353 (0) 1 4517922 Fax: + 353 (0) 1 4517922

ISRAEL

JAMAICA Masterton Ltd, 21-25 Hanover Street, P.O. Box 73 Kingston. Tel: + 18 767 540557 Fax: + 18 769 227807

KOREA S.S. Corporation, Yeouido, P.O. Box 60, Seoul. Tel: 00-822-783-6829 Fax: 00-822-784-9322 Email: sslcorp@chollian.net

MALAYSIA Renold (Malaysia) LOT 2, Jalan Kecapi 33/2, Eilte Industrial Park, Off Jalan Bukit, Kemuning, 40400 Shah Alam, Selangor, Malaysia. Tel: + 60 3 5122 9880 Fax: + 60 3 5191 9881 Email: malaysia@renold.com 201, Jalan Simbang, Taman Perling, 81200 Joho Bharu, Johor, Malaysia. Tel: + 60 (0) 7 2384152-3 Fax: + 60 (0) 7 2384155 Email: malaysia@renold.com 67A, Jalan Medan Ipoh 6, Bandar Baru Medan, 31400 Ipoh, Perak Tel: + 60 (0) 5 548 0059 Fax: + 60 (0) 5 548 0214 Email: malaysia@renold.com


Worldwide Sales and Services 28B Jalan Perai Jaya 3, Bandar Perai Jaya,13600 Perai, Penang, Malaysia Tel: + 604-399 9648 Tel: + 604-399 0648 Fax: + 604-399 5649 Email: malaysia@renold.com

MAURITIUS Dynamotors Ltd, P.O. Box 733, Bell Village, Tel: + 230 2122847/8/9 Fax: + 230 2088348

MEXICO Accessorios Automotrices y Rodamientos Industriales, S.A. de C.V., Calz Legaria 833-A Col Irigacion, Mexico DF 11500 Tel: + 52 5 395 6300 Fax: + 52 5 395 6370

NEW ZEALAND Renold New Zealand, 594 Rosebank Road, Avondale, Auckland. Postal Address: PO Box 19460, Avondale, Auckland. Tel: + 64 (0) 9 828 5018 Fax: + 64 (0) 9 828 5019 Email: aksales@renold.co.nz Christchurch Branch Office, 32 Birmingham Drive, Christchurch, PO Box 9006, Christchurch, Tel: + 64 03 338 2169 Fax: + 64 03 338 8663

NORWAY G. Heier A/S, Postal Address: Postboks 6615, Rodelokka, 0502 Oslo, Norway. Office Address: Thv, Meyersgt. 7, Oslo. Tel: + 47 232 34230 Fax: + 47 232 34242

PERU

SWEDEN

Corporacion Basco S.A.C. Av. Argentina 1165, Lima 1, RUC 25776186. Tel: + 51 1 4336633 Fax: + 51 1 4313188

Renold A/S Skelmarksvej 6, Postboks 90 2605 Brøndby Denmark. Tel: + 45 43 452611 Fax: + 45 43 456592 E-mail: renold@post9.tele.dk

PORTUGAL Harker, Sumner, S.A. Zona Industrial Maia 1 - Sector X 4475 - 132 Gemunde - Maia Portugal. Tel: + 351 229 4478 090 Fax: + 351 229 4478 098 E-mail: accionamantos.ind@harker.pt

SWITZERLAND Renold (Switzerland) Gmbh, Ringstrasse 16, Postfach 1115 CH-8600 Dübendorf 1. Tel: + 41 (0) 1 824 8484 Fax: + 41 (0) 1 824 8411 E-mail: info@renold-gmbh.ch

SINGAPORE Renold Transmission Limited 63 Hillview Avenue, #07-13, Lam Soon Industrial Building, Singapore 669569. Tel: + 65 6760 2422 Fax: + 65 6760 1507 E-mail: renold@mbox5.singnet.com.sg

Route De Prilly 25, CH-1023 Crissier. Tel: + 41 (0) 21 632 9460 Fax: + 41 (0) 21 632 9475 E-mail: crissier@renold-gmbh.ch

THAILAND United Power Engineering Co Ltd 4 Soi Sukhumvit 81 (Siripot) Sukhumvit Road Bangjak, Phrakhanong Bangkok 10260. Tel: + 66 2 7425366 Fax: + 66 2 7425379

SOUTH AFRICA Renold Croft (Pty) Limited, Corner Liverpool and Bolton Streets, Nestadt Industrial Sites, Benoni, 1501 Postal Address: Private Bag x 030, Benoni, 1500. Tel: + 27 (0) 11 747 9500 Fax: + 27 (0) 11 747 9505 E-mail: renold@iafrica.com

TRINIDAD Tracmac Engineering Ltd, P.O. Box 945, Port of Spain, Trinidad, West Indies. Tel: + 1 665 460 1532 Fax: + 1 868 671 0012

P.O. Box 2661, Witbank 1035, Mpumalanga, Republic of South Africa. Tel: +27 (0) 13 692 7760 Fax: +27 (0) 13 697 0546 Email: renoldwit@worldonline.co.za

TURKEY Glengo Ithalat lhracat Mumessillik AS, Gungoren Cad. No. 35 Bagcilar, 34560 Bakirkoy, Istanbul. Tel: + 90 212 4613970 Fax: + 90 212 4613972 www.glengo.com.tr

SPAIN Brown Pestell, Ctra N-11 Lm. 599.5 Nave 5, 08780 Palleja, Barcelona. Tel: + 34 93 6630740 Fax: + 34 93 6632057

UNITED KINGDOM

PAKISTAN

Renold Gears Holroyd Gears Works, Milnrow, Rochdale OL16 3LS Tel: +44 (0) 1706 751000 Fax: +44 (0) 1706 751001 E-mail: sales@gears.renold.com Web: www.renold.com

Brady & Co. of Pakistan Ltd, Shernaz House, P.O. Box 4453, West Wharf Road, Karachi 2. Tel: + 92 21.2310367/201712 Fax: + 92 21.2313376/2313378

Renold Clutches & Couplings Wentloog Corporate Park, Newlands Road, Cardiff CF3 2EU, Wales Tel: + 44 (0) 29 20792737 Fax: + 44 (0) 29 20793004 (Sales):+ 44 (0) 29 20791360 E-mail: couplings@cc.renold.com Web: www.renold.com Renold Hi-Tec Couplings 112 Parkinson Road Halifax HX1 3QH Tel: +44 (0) 1422 255000 Fax: +44 (0) 1422 320273 E-mail: sales@hitec.renold.com Web: www.renold.com Holroyd Harbour Lane North, Milnrow, Rochdale, OL16 3LQ. Tel: +44 (0) 1706 526 590 Fax: +44 (0) 1706 353 350 E-mail: info@holroyd.com Web: www.holroyd.com Renold Chain UK Sales, Horninglow Road, Burton upon Trent, Staffordshire, DE14 2PS. Tel: +44 (0) 1283 512 940 Fax: +44 (0) 1283 512 628 E-mail: enquiry@renold.com

USA Renold Inc Bourne Street, PO Box A, Westfield, New York, 14787-0546 Tel: + 1 716 326 3121 Fax: + 1 716 326 6121 E-mail: renold@cecomet.net

VENEZUELA Equipos Y Acessorios Astral CA, Apartado 1651 Valencia. Tel: + 584 1 332042 Fax: + 584 1 345641

WEB www.renold.com

Terms and Conditions • Whilst all reasonable care in compiling the information contained in this catalogue is taken, no responsibility is accepted for errors. • All information contained in this catalogue is subject to change without notice. • The illustrations used in this catalogue represent the type of product described but the goods supplied may vary in some detail from those illustrated. • The right is reserved to make modifications to the product to meet manufacturing conditions and/or developments (for example in design or materials). • Product can be supplied by Renold companies or representatives around the world on the standard terms and conditions of sale of the company or representative from which the product is purchased. • Copyright Renold Power Transmission Limited 2001. All rights reserved. Nothing contained in this publication shall constitute a part of any contract, express or implied.

• In the interests of safety, customers are reminded that when purchasing any technical product for use at work (or otherwise), any additional or up-to-date information and guidance, which it has not been possible to include in the publication, should be obtained by you from your local sales office in relation to the suitability and the safe and proper use of the product. All relevant information and guidance must be passed on by you to the person engaged in, or likely to be affected by or responsible for the use of the product • The performance levels and tolerances of our product stated in this catalogue (including without limitation, serviceability, wearlife, resistance to fatigue, corrosion protection) have been verified in a programme of testing and quality control in accordance with Renold, independent and/or international standard recommendations. No representations or warranties are given that our product shall meet the stated performance levels or tolerances for any given application outside the performance levels and tolerances for the product’s own specific application and environment.

www.renold.com 51


CANADA Renold Canada Ltd Head Office & Ontario District 121 Roy Boulevard, Brantford, Ontario N3T 5N4 Toll Free Tel: 800 265 9970 Tel: (519) 756 6118 Fax: (519) 756 1767 Email: inquiry@renoldcanada.com www.renoldcanada.com Quebec District 622 rue De Hull, Ville La Salle, Quebec H8R 1V9 Toll Free Tel: 800 361 1414 Tel: (514) 367 1764 Fax: (514) 367 4993 Western District Toll Free Tel: 800 265 9970 Fax: 800 661 6118 Atlantic and Manitoba District Toll Free Tel: 800 265 9970 Fax: 800 661 6118 USA Renold Incorporated 100 Bourne Street Westfield, NY 14787 Toll Free Tel: 1 800 879 2529 Fax: 716 326 8229 www.renoldajax.com WEB www.renold.com

For other country distributors please contact Renold UK.

Superior Gear Technology

www.renold.com


RENOLD helical gear shaft mounted RF series (réducteur de vitesse)