Page 1

DYNA-SYNC速 Drives

DYNA-SYNC

CONTENTS

Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-14 XL Pitch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-18 L Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-24 H Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-30 XH Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-36 Basic HP Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-40 Engineering/Technical Dimensions, Tolerances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-44 Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-44 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-45 Tensioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-45 Belt Working Tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-45 Part Number Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INDEX-1 Keyword Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INDEX-29

PT10-1

Sprockets Conveyor Components

Specification: Belts Dual DYNA-SYNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-11 XL Pitch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-12 L Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-12 H Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-13 XH Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-13 XXH Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-13

Engineering

Specification: Pulleys XL Pitch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-3 L Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-4 H Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-5 XH Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-7 Reborable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-9

HT Synchrous Belts

Features/Benefits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT10-2


DYNA-SYNC

FEATURES/BENEFITS DYNA-SYNC Drives The Original Timing Drive • Synchronized No-Slip Transmission • No Lubrication Required • Efficiency: Approximately 98% • Low Maintenance

HT Synchrous Belts

• Virtually No Backlash • Constant Linear Velocity • Drive Ratios to 8.5:1 • Pitches: XL, L, H, and XH

DYNA-SYNC Belts

DYNA-SYNC Pulleys Sprockets

• Tough, Tensile Cords, No-Stretch Fiberglass • Durable Neoprene Rubber Body • Long-Wearing Nylon Duck Facing • Oil, Heat, and Ozone Resistant

Conveyor Components

• Dual-Sided Teeth Available for Serpentine Drives

• Clean, Compact TAPER-LOCK Design • Easy-on/Easy-off • Precision Manufactured in ISO9000 Certified Plant • Flanged Design Standard on Driver Sizes

Engineering

PT10-2


DYNA-SYNC

SPECIFICATIONS DYNA-SYNC Pulleys - XL, L Pitch

HT Synchrous Belts

TYPE CF

TAPER-LOCK TAPER-LOCK

TYPE C

XL037 - 1/5” Pitch (.375" Wide Belt)

F= 0.56" Wt

32 36 40 42 44 48 60 72

TL32XL037-1108 TL36XL037-1108 TL40XL037-1108 TL42XL037-1108 TL44XL037-1108 TL48XL037-1108 TL60XL037-1210 TL72XL037-1610

113021 113022 113023 113024 113046 113047 113048 113049

.22 .30 .31 .31 .31 .38 .38 .50

Type †

None

TL-1 TL-1 TL-1 TL-1 TL-1 TL-1 TL-1 TL-1

L050 - 3/8” Pitch (.5" Wide Belt) No. Pitch Max. Part of Description Wt. Dia. Flg. No. Teeth (P.D.) O.D. 18 TL18L050-1108 113575 .45 2.149 2.39 20 TL20L050-1108 113581 .68 2.387 2.63 21 TL21L050-1108 113399 .80 2.507 2.87 22 TL22L050-1108 113588 .90 2.626 2.87 24 TL24L050-1210 113464 1.0 2.865 3.11 26 TL26L050-1210 113466 1.2 3.104 3.34 28 TL28L050-1210 113468 1.4 3.342 3.58 30 TL30L050-1610 113470 1.5 3.581 3.83 32 TL32L050-1610 113472 1.9 3.820 4.06 40 TL40L050-2012 113478 2.4 4.775 5.02 48 TL48L050-2012 113484 3.2 5.730 6.02 60 TL60L050-2012 113485 4.9 7.162 None 72 TL72L050-2012 113486 6.5 8.594 84 TL84L050-2517 113487 7.8 10.027 † Dash 1 = Block, 2 = Web, 3 = Arm. (See page PT10-3, V-Drives Section) Letter “F” indicates pulley is flanged.

FEATURES/BENEFITS PAGE PT10-2

Dimensions E

H

L

M

– 0.32 0.32 0.32 0.32 0.32 0.44 0.44

2.04 2.13 2.25 2.37 2.63 2.88 3.50 4.00

0.88 0.88 0.88 0.88 0.88 0.88 1.00 1.00

0 0 0 0 0 0 0 0

Sprockets

Part No.

Brushed Bore Range Min. Max. 1/2 1-1/8 1/2 1-1/8 1/2 1-1/8 1/2 1-1/8 1/2 1-1/8 1/2 1-1/8 1/2 1-1/4 1/2 1-11/16

F=0.75” Type † CF-1 CF-1 CF-1 CF-1 CF-1 CF-1 CF-1 CF-1 CF-1 CF-1 CF-1 C-2 C-2 C-2

BELT SPECIFICATIONS PAGES PT10-11

Bushed Dimensions Bore Range E H L Min. Max 1/2 1-1/8 .13 1.63 .88 1/2 1-1/8 .13 1.81 .88 1/2 1-1/8 .13 2.00 .88 1/2 1-1/8 .13 2.06 .88 1/2 1-1/4 .25 2.25 1.00 1/2 1-1/4 .25 2.56 1.00 1/2 1-1/4 .25 2.75 1.00 1/2 1-11/16 .25 2.88 1.00 1/2 1-11/16 .25 3.06 1.00 1/2 2-1/8 .50 3.94 1.25 1/2 2-1/8 .50 3.94 1.25 1/2 2-1/8 .25 4.38 1.25 1/2 2-1/8 .25 4.38 1.25 1/2 2-11/16 .50 4.38 1.75 ◊ See page PT10-8 - PT10-10 for MPB sizes.

SELECTION PAGES PT10-14

PT10-3

M 0 0 0 0 0 0 0 0 0 0 0 .25 .25 .50

ENGINEERING/TECHNICAL PAGES PT10-44

Conveyor Components

Description ◊

Max. Flg. O.D.

Engineering

No. of Teeth

Pitch Dia. (P.D.) 2.037 2.292 2.546 2.674 2.801 3.056 3.820 4.584


DYNA-SYNC

SPECIFICATIONS DYNA-SYNC Pulleys - L Pitch

HT Synchrous Belts

TYPE DF

TYPE CF

TYPE D

TYPE C

Sprockets

L075 - 3/8” Pitch (.75" Wide Belt) No. Description Part of ◊ No. Teeth 18 TL18L075-1108 113589 20 TL20L075-1108 113594 22 TL22L075-1108 113595 24 TL24L075-1210 113513 26 TL26L075-1210 113515 28 TL28L075-1610 113517 30 TL30L075-1610 113519 32 TL32L075-1610 113521 40 TL40L075-2012 113527 48 TL48L075-2012 113533 60 TL60L075-2012 113534 72 TL72L075-2012 113535 84 TL84L075-2517 113536

F=1.00” Wt. .45 .68 .90 1.0 1.2 1.2 1.5 1.9 2.4 3.2 4.9 6.5 7.8

Pitch Dia. (P.D.) 2.149 2.387 2.626 2.865 3.104 3.342 3.581 3.820 4.775 5.730 7.162 8.594 10.027

Max. Flg. O.D. 2.39 2.63 2.87 3.11 3.34 3.58 3.83 4.06 5.02 6.02 None

Conveyor Components Engineering

L100 - 3/8" Pitch (1" Wide Belt) No. Pitch Max. Description Part of Wt. Dia. Flg. ◊ No. Teeth (P.D.) O.D. 18 TL18L100-1108 113599 .7 2.149 2.39 20 TL20L100-1108 113641 1.0 2.387 2.63 22 TL22L100-1108 113669 1.3 2.626 2.87 24 TL24L100-1210 113562 1.3 2.865 3.11 26 TL26L100-1210 113564 1.7 3.104 3.34 28 TL28L100-1610 113566 1.7 3.342 3.58 30 TL30L100-1610 113568 2.2 3.581 3.83 32 TL32L100-1610 113570 2.7 3.820 4.06 40 TL40L100-2012 113576 3.6 4.775 5.02 48 TL48L100-2012 113582 5.1 5.730 6.02 60 TL60L100-2012 113583 6.0 7.162 72 TL72L100-2012 113584 8.0 8.594 None 84 TL84L100-2517 113585 9.2 10.027 † Dash 1 = Block, 2 = Web, 3 = Arm. (See page PT10-3, V-Drives Seciton) Letter "F" indicates pulley is flanged.

FEATURES/BENEFITS PAGE PT10-2

TYPE KF

Type † KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 CF-1 CF-1 C-2 C-1 C-1

Bushed Bore Range Min. Max. 1/2 1-1/8 1/2 1-1/8 1/2 1-1/8 1/2 1-1/4 1/2 1-1/4 1/2 1-11/16 1/2 1-11/16 1/2 1-11/16 1/2 2-1/8 1/2 2-1/8 1/2 2-1/8 1/2 2-1/8 1/2 2-11/16

Dimensions E

H

L

M

.06 .06 .06 0 0 0 0 0 .25 .25 .13 .13 .25

.... .... .... .... .... .... .... .... 3.94 3.94 4.38 4.38 4.88

.88 .88 .88 1.00 1.00 1.00 1.00 1.00 1.25 1.25 1.25 1.25 1.75

.06 .06 .06 .... .... .... .... .... 0 0 .13 .13 .50

F=1.25” Type † KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 C-2 C-2 C-1

BELT SPECIFICATIONS PAGES PT10-11

Bushed Dimensions Bore Range E H L Min. Max. 1/2 1-1/8 .06 ... .87 1/2 1-1/8 .06 ... .87 1/2 1-1/8 .06 ... .87 1/2 1-1/4 .06 ... 1 1/2 1-1/4 .06 ... 1 1/2 1-11/16 .11 ... 1 1/2 1-11/16 .11 ... 1 1/2 1-11/16 .25 ... 1 1/2 2-1/8 0 ... 1.25 1/2 2-1/8 0 ... 1.25 1/2 2-1/8 0 4.38 1.25 1/2 2-1/8 0 4.38 1.25 1/2 2-11/16 .55 4.88 1.75 ◊ See page PT10-8 - PT10-10 for MPB sizes.

SELECTION PAGES PT10-14

PT10-4

M .31 .31 .31 .19 .19 .15 .15 0 .... .... .... ....

ENGINEERING/TECHNICAL PAGES PT10-44


DYNA-SYNC

SPECIFICATIONS DYNA-SYNC Pulleys - L, H † Dash 1 = Block, 2 = Web, 3 = Arm. Letter "F" indicates pulley is flanged.

+ Available from stock in Min. Plain Bore (MPB) only. Max. bore is without keyway. (If keyway is used, reduce max. bore listed by twice the keyway depth.)

HT Synchrous Belts

◊ See page PT10-9 for additional MPB sizes.

113678 113684 113605 113608 113611 113642 113615 113617 113620 113623 113629 113635 113636 113637 113638 113639 113640

H150 - 1/2" Pitch (1.5" Wide Belt) No. Description Part of No. ◊ Teeth 14 16 18 20 22 24 26 28 30 32 40 48 60 72 84 96 120

TL14H150-1108 TL16H150-1108 TL18H150-1210 TL20H150-1210 TL22H150-1610 TL24H150-2012 TL26H150-2012 TL28H150-2012 TL30H150-2012 TL32H150-2517 TL40H150-2517 TL48H150-2517 TL60H150-3020 TL72H150-3020 TL84H150-3020 TL96H150-3020 TL120H150-3020 FEATURES/BENEFITS PAGE PT10-2

113691 113692 113693 113694 113695 113663 113665 113667 113670 113673 113679 113685 113686 113687 113688 113689 113690

.8 1.3 1.2 1.7 1.8 2.3 2.2 2.8 4.2 4.1 7.8 12.1 10.3 14 20 27 38

2.228 2.546 2.865 3.183 3.501 3.820 4.138 4.456 4.775 5.093 6.366 7.639 9.549 11.459 13.369 15.279 19.099

2.48 2.80 3.11 3.44 3.75 4.02 4.39 4.70 5.02 5.33 6.58 8.02

None

Min.

Max.

E

H

L

M

KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 CF-1 CF-1 CF-1 C-2 C-1 C-2 C-2 C-3

1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 7/8 7/8 7/8 7/8 7/8

1-1/8 1-1/8 1-1/4 1-1/4 1-11/16 1-11/16 2-1/8 2-1/8 2-1/8 2-11/16 2-11/16 2-11/16 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4

.06 .06 .06 .11 .11 .11 .06 .06 .06 .44 .44 .44 .34 .34 .34 .34 0

.... .... .... .... .... .... .... .... .... 4.44 4.44 4.44 6.25 6.25 6.25 6.25 6.25

.88 .88 1 1 1 1 1.25 1.25 1.25 1.75 1.75 1.75 2 2 2 2 2

.42 .42 .25 .25 .25 .25 0 0 0 0 0 0 .34 .34 .34 .34 .59

Type †

Bore Range Min.

Max.

E

H

L

M

KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 AF-2 C-2 C-2 C-3 C-3 C-3

1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 7/8 7/8 7/8 7/8 7/8

1 1 1-1/4 1-1/4 1-11/16 2-1/8 2-1/8 2-1/8 2-1/8 2-11/16 2-11/16 2-11/16 3-1/4 3-1/4 3-1/4 3-15/16 3-1/4

.47 .47 .11 .11 .11 .56 .56 .56 .56 .11 .11 0 .09 .09 .09 .09 .09

.... .... .... .... .... .... .... .... .... .... .... .... 6.25 6.25 6.25 6.25 6.25

.88 .88 1 1 1 1.25 1.25 1.25 1.25 1.75 1.75 1.75 2 2 2 2 2

.88 .88 .75 .75 .75 0 0 0 0 0 0 .06 .09 .09 .09 .09 .09

F=1.86” Wt. 1.0 1.5 1.6 2.2 2.5 2.2 3.2 4.1 5.1 4.6 8.6 13.6 12.3 17.0 21.5 31 40

Pitch Dia. (P.D.) 2.228 2.546 2.865 3.183 3.501 3.820 4.138 4.456 4.775 5.093 6.366 7.639 9.549 11.459 13.369 15.279 19.099

Max. Flg. O.D. 2.48 2.80 3.11 3.44 3.75 4.06 4.78 4.70 5.02 5.33 6.58 8.02

None

BELT SPECIFICATIONS PAGES PT10-11

SELECTION PAGES PT10-14

PT10-5

Dimensions

ENGINEERING/TECHNICAL PAGES PT10-44

Sprockets

TL14H100-1108 TL16H100-1108 TL18H100-1210 TL20H100-1210 TL22H100-1610 TL24H100-1610 TL26H100-2012 TL28H100-2012 TL30H100-2012 TL32H100-2517 TL40H100-2517 TL48H100-2517 TL60H100-3020 TL72H100-3020 TL84H100-3020 TL96H100-3020 TL120H100-3020

Dimensions

Conveyor Components

14 16 18 20 22 24 26 28 30 32 40 48 60 72 84 96 120

F=1.32” Bore Range

Type †

Engineering

H100 - 1/2" Pitch (1" Wide Belt) (for H075 & H100 Belts) Pitch Max. No. Description Part Wt. Dia. Flg. of No. ◊ (P.D.) O.D. Teeth


DYNA-SYNC

SPECIFICATIONS DYNA-SYNC Pulleys - H

HT Synchrous Belts

TYPE DF

TYPE CF

TYPE D

TYPE C

Sprockets

H200 - 1/2" Pitch (2" Wide Belt) No. Description Part of ◊ No. Teeth 16 TL16H200-1108 113072 18 TL18H200-1215 113704 20 TL20H200-1215 113707 22 TL22H200-1615 113710 24 TL24H200-2012 113712 26 TL26H200-2012 113714 28 TL28H200-2012 113716 30 TL30H200-2012 113719 32 TL32H200-2517 113722 40 TL40H200-2517 113728 48 TL48H200-3020 113734 60 TL60H200-3020 113735 72 TL72H200-3020 113736 84 TL84H200-3020 113737 96 TL96H200-3535 113738 120 TL120H200-3020 113739

TYPE AF

TYPE KF

F=2.34” Wt. 1.9 1.8 2.6 28 2.6 3.6 5.1 7.0 5.5 9.9 14.3 15.3 21 23 34 42

Pitch Dia. (P.D.) 2.546 2.865 3.183 3.501 3.820 4.138 4.456 4.775 5.093 6.366 7.639 9.549 11.459 13.369 15.279 19.099

Max. Flg. O.D. 2.80 3.11 3.44 3.75 4.06 4.78 4.70 5.02 5.33 6.58 8.02

None

Conveyor Components Engineering

BELT SPECIFICATIONS PAGES PT10-11

Bore Range MIn.

Max.

E

H

L

M

KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 A-2 A-2 A-3 C-3 A-3

1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 7/8 7/8 7/8 7/8 1-3/16 7/8

1-1/8 1-1/4 1-1/4 1-5/8 2 2 2 2 2-1/2 2-1/2 3 3 3-1/4 3-1/4 3-15/16 3-1/4

.75 .44 .42 .42 .55 .55 .55 1.09 .59 .59 .41 .17 0 0 .40 0

0 0 0 0 0 0 0 0 0 0 0 0 0 0 7.0 0

.88 1.5 1.5 1.5 1.25 1.25 1.25 1.25 1.75 1.75 2 2 2 2 3.5 2

.72 .41 .42 .42 .55 .55 .55 0 0 0 0 .17 .34 .34 .75 .34 F=3.38”

Bushed Dimensions Bore Range E H L Min. Max. 1/2 1-1/8 1.28 0 .87 1/2 1-1/4 .94 0 1.5 1/2 1-1/4 .94 0 1.5 1/2 1-11/16 .94 0 1.5 1/2 2-1/8 1.06 0 1.25 1/2 2-1/8 1.06 0 1.25 1/2 2-1/8 1.06 0 1.25 1/2 2-1/8 1.06 0 1.25 1/2 2-11/16 .81 0 1.75 1/2 2-11/16 .81 0 1.75 7/8 3-1/4 .69 0 2 7/8 3-1/4 .69 0 2 7/8 3-1/4 .31 0 2 7/8 3-1/4 .69 0 2 1-3/16 3-15/16 .06 0 3.5 1-3/16 3-15/16 .125 7.0 3.5 ◊ See page PT10-8 - PT10-10 for MPB sizes. SELECTION PAGES PT10-14

PT10-6

Dimensions

Type †

H300 - 1/2" Pitch (3" Wide Belt) No. Pitch Max. Description Part Type of Wt. Dia. Flg. ◊ No. † Teeth (P.D.) O.D. 16 TL16H300-1108 113073 2.5 2.546 2.80 KF-1 18 TL18H300-1215 113752 2.6 2.865 3.11 KF-1 3.9 3.183 3.44 KF-1 20 TL20H300-1215 113755 22 TL22H300-1615 113758 4.0 3.501 3.75 KF-1 24 TL24H300-2012 113760 4.3 3.820 4.06 KF-1 26 TL26H300-2012 113762 5.4 4.138 4.78 KF-1 28 TL28H300-2012 113764 6.8 4.456 4.70 KF-1 30 TL30H300-2012 113767 7.5 4.775 5.02 KF-1 32 TL32H300-2517 113770 7.4 5.093 5.33 KF-1 40 TL40H300-2517 113776 12.1 6.366 6.58 KF-1 48 TL48H300-3020 113782 16.3 7.639 8.02 KF-1 60 TL60H300-3020 113783 17.3 9.549 A-2 72 TL72H300-3020 113784 23 11.459 A-2 84 13.369 A-3 TL84H300-3020 113785 30 None 96 TL96H300-3535 113786 38 15.279 C-3 120 TL120H300-3535 113787 51 19.099 C-3 † Dash 1 = Block, 2 = Web, 3 = Arm. Letter "F" indicates pulley is flanged. FEATURES/BENEFITS PAGE PT10-2

TYPE A

M 1.23 .94 .94 .94 1.06 1.06 1.06 1.06 .81 .81 .69 .69 1.06 .69 .06 0

ENGINEERING/TECHNICAL PAGES PT10-44


DYNA-SYNC

SPECIFICATIONS DYNA-SYNC Pulleys - XH

TYPE D

TYPE C F=2.56”

None

Bore Range

Dimensions

Type †

Min.

Max.

E

H

L

M

KF-1 KF-1 KF-1 KF-1 KF-1 CF-1 CF-1 CF-1 CF-1 C-2 C-3

1/2 1/2 1/2 7/8 7/8 1-3/16 1-3/16 1-3/16 1-7/16 1-7/16 1-7/16

2-1/8 2-1/8 2-11/16 3-1/4 3-1/4 3-15/16 3-15/16 3-15/16 4-7/16 4-7/16 4-7/16

.84 .84 .81 .56 .56 .94 .94 .94 1.44 .72 .72

... ... .... .... .... 6.50 6.50 6.50 8.50 8.50 8.50

1.25 1.25 1.75 2.0 2.0 3.5 3.5 3.5 4.0 4.0 4.0

.47 .47 0 0 0 0 0 0 0 .72 .72

Sprockets

12 16 10.6 11.3 13.3 13.5 18.5 21.5 37.5 44.5 47

Max. Flg. O.D. 5.58 6.11 6.59 7.28 7.78 8.27 9.31 9.52 11.80

F=3.63” Type † KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 KF-1 CF-1 C-1 C-3

BELT SPECIFICATIONS PAGES PT10-11

Bore Range Min.

Max.

E

H

L

M

1/2 2-1/8 1.38 ... 1.25 1.0 1/2 2-1/8 1.38 ... 1.25 1.0 1/2 2-11/16 .94 .... 1.75 .94 7/8 3-1/4 .81 .... 2.0 .81 7/8 3-1/4 .81 .... 2.0 .81 1-3/16 3-15/16 .13 .... 3.5 .... 1-3/16 3-15/16 .13 .... 3.5 .... 1-3/16 3-15/16 .13 .... 3.5 .... 1-7/16 4-7/16 .38 7.50 4.0 .... 1-7/16 4-7/16 .19 8.50 4.0 .19 1-7/16 4-7/16 .19 8.50 4.0 .19 XXH Pullley Note: Discontinued Product. Recommend that drive be redesigned to HT100 or HT150. Refer to HT section of this catalog.

SELECTION PAGES PT10-14

PT10-7

Dimensions

ENGINEERING/TECHNICAL PAGES PT10-44

Conveyor Components

Wt.

Pitch Dia. (P.D.) 5.013 5.570 6.127 6.685 7.241 7.799 8.356 8.913 11.141 13.369 16.711

XH300 - 7/8" Pitch (3" Wide Belt) No. Pitch Max. Part of Description Wt. Dia. Flg. No. Teeth (P.D.) O.D. 5.013 5.58 18 TL18XH300-2012 113121 15 20 TL20XH300-2012 113122 19 5.570 6.11 22 TL22XH300-2517 113854 13.6 6.127 6.59 24 TL24XH300-3020 113857 15.3 6.685 7.28 26 TL26XH300-3020 113860 17.3 7.241 7.78 28 TL28XH300-3535 113863 17.3 7.799 8.27 30 TL30XH300-3535 113866 22.5 8.356 9.31 32 TL32XH300-3535 113869 26.5 8.913 9.52 43.5 11.141 11.80 40 TL40XH300-4040 113872 48 TL48XH300-4040 113873 51.5 13.369 None 60 TL60XH300-4040 113874 55.5 16.711 † Dash 1 = Block, 2 = Web, 3 = Arm. (See page PT10-3, V-Drives Seciton) Letter "F" indicates pulley is flanged.

FEATURES/BENEFITS PAGE PT10-2

TYPE KF

Engineering

XH200 - 7/8" Pitch (2" Wide Belt) No. Part of Description No. Teeth 18 TL18XH200-2012 113074 20 TL20XH200-2012 113120 22 TL22XH200-2517 113804 24 TL24XH200-3020 113807 26 TL26XH200-3020 113810 28 TL28XH200-3535 113813 30 TL30XH200-3535 113816 32 TL32XH200-3535 113819 40 TL40XH200-4040 113822 48 TL48XH200-4040 113823 60 TL60XH200-4040 113824

TYPE CF

HT Synchrous Belts

TYPE DF


DYNA-SYNC

SPECIFICATIONS DYNA-SYNC Pulleys - XL037 TYPE DF

HT Synchrous Belts

TYPE D Minimum Plain Bore

Minimum Plain Bore

Sprockets Conveyor Components

XL037 -1/5" Pitch (.375" Wide Belt) - MINIMUM PLAIN BORE No. Pitch Max. Part of Description Wt. Dia. Flg. No. Teeth (P.D.) O.D. 10 10XL037-MPB 114300 .03 .637 0.94 11 11XL037-MPB 113401 .03 .700 0.95 12 12XL037-MPB 113402 .06 .764 1.01 14 14XL037-MPB 113403 .06 .891 1.14 15 15XL037-MPB 113404 .09 .955 1.20 16 16XL037-MPB 113405 .09 1.019 1.27 18 18XL037-MPB 113406 .13 1.146 1.39 20 20XL037-MPB 113407 .19 1.273 1.52 21 21XL037-MPB 113408 .19 1.337 1.58 22 22XL037-MPB 113409 .22 1.401 1.64 24 24XL037-MPB 113410 .25 1.528 1.78 28 28XL037-MPB 113411 .34 1.783 2.03 30 30XL037-MPB 113412 .41 1.910 2.16 32 32XL037-MPB 113413 .22 2.037 36 36XL037-MPB 113414 .30 2.292 40 40XL037-MPB 113415 .31 2.546 42 42XL037-MPB 113416 .31 2.674 None 44 44XL037-MPB 113417 .31 2.801 48 48XL037-MPB 113418 .38 3.056 60 60XL037-MPB 113419 .38 3.820 72 72XL037-MPB 113420 .50 4.584 † Dash 1 = Block, 2 = Web, 3 = Arm. (See page PT10-3, V-Drives Seciton) Letter "F" indicates pulley is flanged.

F= 0.56 Type † DF-1 DF-1 DF-1 DF-1 DF-1 DF-1 DF-1 DF-1 DF-1 DF-1 DF-1 DF-1 DF-1 D-1 D-1 D-1 D-2 D-2 D-2 D-2 D-2

Reborable Bore* St'k. Max. 3/16 3/16 3/16 3/16 3/16 1/4 1/4 1/4 1/4 5/16 1/4 3/8 1/4 1/2 1/4 9/16 1/4 9/16 1/4 5/8 1/4 11/16 1/4 13/16 5/16 15/16 5/16 1-3/16 5/16 1-3/16 5/16 1-3/16 5/16 1-3/16 5/16 1-3/16 5/16 1-3/16 3/8 1-3/16 3/8 1-3/16

Dimensions E

H

L

0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.35 0.35 0.35 0.35 0.35 0.35 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44

0.49 0.49 0.50 0.56 0.63 0.69 0.81 0.94 0.94 1.00 1.06 1.19 1.38 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50

0.813 0.813 0.813 0.813 0.813 0.813 0.813 0.88 0.88 0.88 0.91 0.91 0.91 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00

* Max. bore is without keyway. (If keyway is used, reduce

max. bore listed by twice the keyway depth.) Standard keyways are listed above. Two hex-socket set screws furnished @ 90° are included in price of pulley.

Engineering FEATURES/BENEFITS PAGE PT10-2

BELT SPECIFICATIONS PAGES PT10-11

SELECTION PAGES PT10-14

PT10-8

ENGINEERING/TECHNICAL PAGES PT10-44


Diameter Pitch Flange

Wt.

Type

Stock

Bore Max.

H

Dimensions L

3/8 3/8 3/8 3/8 3/8 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2

1/2 3/4 3/4 7/8 7/8 1 1 1 1 1 1-1/4 1-1/4 1-3/8 1-3/8 1-3/8 1-3/8 1-5/8 2-5/16 2-3/8

.81 1.06 1.13 1.13 1.34 1.44 1.44 1.56 1.69 1.69 2.00 2.00 2.25 2.25 2.25 2.25 2.63 3.50 3.63

1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25

3/8 3/8 3/8 1/2 1/2 1/2 1/2 1/2 1/2 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8

13/16 3/4 7/8 7/8 1 1 1 1 1-1/4 1-1/4 1-1/4 1-3/8 1-3/8 1-3/8 1-3/8 1-5/8 2-5/16 2-3/8

1.06 1.13 1.13 1.34 1.44 1.44 1.56 1.69 1.69 2.00 2.00 2.25 2.25 2.25 2.25 2.63 3.50 3.63

1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50

3/8 3/8 1/2 1/2 1/2 1/2 1/2 1/2 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8

3/4 7/8 7/8 1 1 1 1 1 1-1/4 1-1/4 1-3/8 1-5/8 1-3/4 1-7/8 2 2-5/16 2-5/16

1.13 1.13 1.34 1.44 1.44 1.56 1.69 1.69 2.00 2.00 2.25 2.44 2.69 2.81 3.13 3.50 3.63

1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75

L050 (.5" Wide Belt) 113450+ 113451+ 114441+ 113452+ 114442+ 113453+ 114301+ 114302 114303 114304 114305 114306 114307 114308 114309 114310 114311 114443 114444

0.28 0.3 0.4 0.4 0.6 0.6 0.8 0.8 0.9 1.0 1.3 1.4 1.8 2.1 2.3 2.4 3.0 3.8 4.6

1.194 1.432 1.552 1.671 1.790 1.910 2.029 2.149 2.268 2.387 2.507 2.626 2.865 3.104 3.342 3.581 3.820 4.297 4.775

113500+ 114445+ 113501+ 114446+ 113502+ 114312+ 114313 114314 114315 114316 114317 114318 114319 114320 114321 114322 114447 114448

0.4 0.6 0.5 0.8 0.7 1.0 1.0 1.3 1.3 1.6 1.8 2.1 2.4 2.9 3.0 3.6 4.4 5.0

1.432 1.552 1.671 1.790 1.910 2.029 2.149 2.268 2.387 2.507 2.626 2.865 3.104 3.342 3.581 3.820 4.297 4.775

1.44 1.67 1.81 1.92 2.06 2.16 2.31 2.38 2.50 2.63 2.73 2.88 3.13 3.38 3.63 3.81 4.06 4.69 5.00

DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF

L075 (.75" Wide Belt) 12 13 14 15 16 17 18 19 20 21 22 24 26 28 30 32 36 40

12L075-MPB 13L075-MPB 14L075-MPB 15L075-MPB 16L075-MPB 17L075-MPB 18L075-MPB 19L075-MPB 20L075-MPB 21L075-MPB 22L075-MPB 24L075-MPB 26L075-MPB 28L075-MPB 30L075-MPB 32L075-MPB 36L075-MPB 40L075-MPB

1.67 1.81 1.92 2.06 2.16 2.31 2.38 2.50 2.63 2.73 2.88 3.13 3.38 3.63 3.81 4.06 4.69 5.00

DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF

L100 (1" Wide Belt) 13 13L100-MPB 114449+ 0.7 1.552 1.81 DF 14 14L100-MPB 113550+ 0.6 1.671 1.92 DF 15 15L100-MPB 114450+ 1.0 1.790 2.06 DF 16 16L100-MPB 113551+ 0.8 1.910 2.16 DF 17 17L100-MPB 114323+ 1.0 2.029 2.31 DF 18 18L100-MPB 114324 1.2 2.149 2.38 DF 19 19L100-MPB 114325 1.4 2.268 2.50 DF 20 20L100-MPB 114326 1.8 2.387 2.63 DF 21 21L100-MPB 114327 2.0 2.507 2.73 DF 22 22L100-MPB 114328 2.1 2.626 2.88 DF 24 24L100-MPB 114329 2.5 2.865 3.13 DF 26 26L100-MPB 114330 3.0 3.104 3.38 DF 28 28L100-MPB 114331 3.6 3.342 3.63 DF 30 30L100-MPB 114332 4.1 3.581 3.81 DF 32 32L100-MPB 114333 4.8 3.820 4.06 DF 36 36L100-MPB 114451 5.4 4.297 4.69 DF 40 40L100-MPB 114452 6.0 4.775 5.00 DF + Available from stock in Min. Plain Bore (MPB) only. Max. bore is without keyway. (If keyway is used, reduce max. bore listed by twice the keyway depth.)

FEATURES/BENEFITS PAGE PT10-2

BELT SPECIFICATIONS PAGES PT10-11

SELECTION PAGES PT10-14

PT10-9

E F=0.75" 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 F=1.00" 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 F=1.25" 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50

ENGINEERING/TECHNICAL PAGES PT10-44

Sprockets

Part No.

Conveyor Components

No. Description Teeth L Pitch - 3/8" Pitch 10 10L050-MPB 12 12L050-MPB 13 13L050-MPB 14 14L050-MPB 15 15L050-MPB 16 16L050-MPB 17 17L050-MPB 18 18L050-MPB 19 19L050-MPB 20 20L050-MPB 21 21L050-MPB 22 22L050-MPB 24 24L050-MPB 26 26L050-MPB 28 28L050-MPB 30 30L050-MPB 32 32L050-MPB 36 36L050-MPB 40 40L050-MPB

Engineering

DYNA-SYNC Pulleys - Reborable

HT Synchrous Belts

DYNA-SYNC

SPECIFICATIONS


DYNA-SYNC

SPECIFICATIONS DYNA-SYNC Pulleys - Reborable

TYPE DF

HT Synchrous Belts

TYPE D No. Description Teeth H Pitch - 1/2" Pitch

Part No.

Wt.

Diameter Pitch Flange

Type

Bore

Dimensions L

Sprockets Conveyor Components

Stock

Max.

H

5/8 5/8 5/8 5/8 5/8 5/8 3/4 3/4 3/4 3/4 3/4 3/4

7/8 1-1/8 1-1/4 1-3/8 1-1/2 1-5/8 1-11/16 1-3/4 1-7/8 2-1/4 2-5/16 2-3/8

1.63 1.88 2.00 2.25 2.38 2.50 2.66 2.75 3.00 3.38 3.50 3.63

1.88 2.00 2.00 2.00 2.00 2.13 2.13 2.25 2.25 2.38 2.38 2.38

3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4

7/8 1-1/8 1-1/4 1-3/8 1-1/2 1-5/8 1-11/16 1-3/4 1-7/8 2-1/4 2-5/16 2-3/8

1.63 1.88 2.00 2.25 2.38 2.50 2.66 2.75 3.00 3.38 3.50 3.63

2.38 2.50 2.50 2.50 2.50 2.63 2.63 2.75 2.75 2.75 2.88 2.88

3/4 3/4 3/4 3/4 3/4 3/4 1 1 1 1 1 1

7/8 1-1/8 1-1/4 1-3/8 1-1/2 1-5/8 1-11/16 1-3/4 1-7/8 2-1/4 2-5/16 2-3/8

1.63 1.88 2.00 2.25 2.38 2.50 2.66 2.75 3.00 3.38 3.50 3.63

2.91 3.03 3.03 3.03 3.03 3.16 3.16 3.28 3.28 3.41 3.41 3.41

3/4 3/4 3/4 3/4 3/4 1 1 1-1/8 1-1/8 1-1/8 1-1/8

1-1/8 1-1/4 1-3/8 1-1/2 1-5/8 1-11/16 1-3/4 1-7/8 2-1/4 2-5/16 2-3/8

1.88 2.00 2.25 2.38 2.50 2.66 2.75 3.00 3.38 3.50 3.63

4.06 4.06 4.06 4.06 4.19 4.19 4.31 4.31 4.44 4.44 4.44

H100 (1" Wide Belt)

14 16 17 18 19 20 21 22 24 26 28 30

14H100-MPB 16H100-MPB 17H100-MPB 18H100-MPB 19H100-MPB 20H100-MPB 21H100-MPB 22H100-MPB 24H100-MPB 26H100-MPB 28H100-MPB 30H100-MPB

114334 114335 114453 114336 114337 114338 114339 114340 114341 114342 114343 114454

1.4 2.0 2.3 2.8 3.1 3.6 3.9 4.5 5.6 7.0 8.0 9.1

2.228 2.546 2.706 2.865 3.024 3.183 3.342 3.501 3.820 4.138 4.456 4.775

14 16 17 18 19 20 21 22 24 26 28 30

14H150-MPB 16H150-MPB 17H150-MPB 18H150-MPB 19H150-MPB 20H150-MPB 21H150-MPB 22H150-MPB 24H150-MPB 26H150-MPB 28H150-MPB 30H150-MPB

114344 114345 114455 114346 114347 114348 114349 114350 114351 114352 114353 114456

1.8 2.5 3.0 3.4 3.9 4.5 5.0 5.8 6.9 8.5 10.1 11.5

2.228 2.546 2.706 2.865 3.024 3.183 3.342 3.501 3.820 4.138 4.456 4.775

14 16 17 18 19 20 21 22 24 26 28 30

14H200-MPB 16H200-MPB 17H200-MPB 18H200-MPB 19H200-MPB 20H200-MPB 21H200-MPB 22H200-MPB 24H200-MPB 26H200-MPB 28H200-MPB 30H200-MPB

114354 114355 114457 114356 114357 114358 114359 114360 114361 114362 114363 114458

2.3 3.3 3.8 4.4 5.0 5.3 5.9 6.9 8.3 10.2 11.8 13.5

2.228 2.546 2.706 2.865 3.024 3.183 3.342 3.501 3.820 4.138 4.456 4.775

16 17 18 19 20 21 22 24 26 28 30

16H300-MPB 17H300-MPB 18H300-MPB 19H300-MPB 20H300-MPB 21H300-MPB 22H300-MPB 24H300-MPB 26H300-MPB 28H300-MPB 30H300-MPB

114364 114459 114365 114366 114367 114368 114369 114370 114371 114372 114460

4.5 5.1 6.0 6.6 7.5 9.0 10.9 12.0 13.4 15.6 18.0

2.546 2.706 2.865 3.024 3.183 3.342 3.501 3.820 4.138 4.456 4.775

2.44 2.88 3.00 3.13 3.38 3.38 3.63 3.81 4.06 4.38 4.69 5.00

DF DF DF DF DF DF DF DF DF DF DF DF

H150 (1.5" Wide Belt) 2.44 2.88 3.00 3.13 3.38 3.38 3.63 3.81 4.06 4.38 4.69 5.00

DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF

Engineering

FEATURES/BENEFITS PAGE PT10-2

DF DF DF DF DF DF DF DF DF DF DF

BELT SPECIFICATIONS PAGES PT10-11

0.63 0.75 0.75 0.75 0.75 0.88 0.88 1 1 1.13 1.13 1.13

F=4.06"

SELECTION PAGES PT10-14

PT10-10

0.63 0.75 0.75 0.75 0.75 0.88 0.88 1 1 1 1.13 1.13

F=2.28"

H300 (3" Wide Belt) 2.88 3.00 3.13 3.38 3.38 3.63 3.81 4.06 4.38 4.69 5.00

0.63 0.75 0.75 0.75 0.75 0.88 0.88 1 1 1.13 1.13 1.13

F=1.75"

H200 (2" Wide Belt) 2.44 2.88 3.00 3.13 3.38 3.38 3.63 3.81 4.06 4.38 4.69 5.00

E F=1.25"

0.75 0.75 0.75 0.75 0.88 0.88 1 1 1.13 1.13 1.13

ENGINEERING/TECHNICAL PAGES PT10-44


Dual DYNA-SYNC Belts DXL Series Dual DYNA-SYNC Belts Belt Lgth.

DL Series Dual DYNA-SYNC Belts Belt Lgth. 15.0 18.7 21.0 22.5 24.0 25.5 27.0 28.5 30.0 32.2 34.5 36.7 39.0 42.0 45.0 48.0 51.0 54.0 60.0 66.0

L050 (1/2” Wide) Belt Part No. No. D150L050 110187 D187L050 110190 D210L050 110193 D225L050 110196 D240L050 110199 D255L050 110202 D270L050 110205 D285L050 110208 D300L050 110211 D322L050 110214 D345L050 110217 D367L050 110220 D390L050 110223 D420L050 110226 D450L050 110229 D480L050 110232 D510L050 110235 D540L050 110238 D600L050 110241 D660L050 110244 Avg. Wt. .14Lb.

3/8” Pitch (L) L075 (3/4” Wide) Belt Part No. No. D150L075 110158 D187L075 110191 D210L075 110194 D225L075 110197 D240L075 110200 D255L075 110203 D270L075 110206 D285L075 110209 D300L075 110212 D322L075 110215 D345L075 110218 D367L075 110221 D390L075 110224 D420L075 110227 D450L075 110230 D460L075 110233 D510L075 110236 D540L075 110239 D600L075 110242 D660L075 110245 Avg. Wt. .21Lb.

L100 (1” Wide) Belt Part No. No. D150L100 110189 D187L100 110192 D210L100 110195 D255L100 110198 D240L100 110201 D255L100 110204 D270L100 110207 D285L100 110210 D300L100 110213 D322L100 110216 D345L100 110219 D367L100 110222 D390L100 110225 D420L100 110228 D450L100 110231 D480L100 110234 D510L100 110237 D540L100 110240 D600L100 110243 D660L100 110246 Avg. Wt. .26Lb.

Sprockets

For Serpentine Drives

12.0 13.0 14.0 15.0 16.0 17.0 18.0 19.0 20.0 21.0 22.0 23.0 24.0 25.0 26.0 28.0 29.0 30.0 31.0 33.0

1/5” Pitch (XL) XL025 (1/4” Wide) XL037 (3/8” Wide) Belt Part Belt Part No. No. No. No. D120XL025 110132 D120XL037 110133 D130XL025 110134 D130XL037 110135 D140XL025 110136 D140XL037 110137 D150XL025 110138 D150XL037 110139 D160XL025 110140 D160XL037 110141 D170XL025 110142 D170XL037 110143 D180XL025 110144 D180XL037 110145 D190XL025 110146 D190XL037 110147 D200XL025 110148 D200XL037 110149 D210XL025 110150 D210XL037 110151 D220XL025 110152 D220XL037 110153 D230XL025 110154 D230XL037 110155 D240XL025 110156 D240XL037 110157 D250XL025 110158 D250XL037 110159 D260XL025 110160 D260XL037 110161 D280XL025 110162 D280XL037 110163 D290XL025 110164 D290XL037 110165 D300XL025 110166 D300XL037 110167 D310XL025 110168 D310XL037 110169 D330XL025 110170 D330XL037 110171 Avg. Wt. .03Lb. Avg. Wt. 0.5Lb.

HT Synchrous Belts

DYNA-SYNC

SPECIFICATIONS

H075 (3/4” Wide) Belt No. Part No. D240H075 110247 D270H075 110252 D300H075 110257 D330H075 110262 D360H075 110267 D390H075 110272 D420H075 110277 D450H075 110282 D480H075 110287 D510H075 110292 D540H075 110297 D570H075 110302 D600H075 110307 D630H075 110312 D660H075 110317 D700H075 110322 D750H075 110327 D800H075 110332 D850H075 110337 D900H075 110342 D1000H075 110347 D1100H075 110352 D1250H075 110357 D1400H075 110362 D1700H075 110367 Avg. Wt. .35Lb. FEATURES/BENEFITS PAGE PT10-2

H100 (1” Wide) Belt No. Part No. D240H100 110248 D270H100 110253 D300H100 110258 D330H100 110263 D360H100 110268 D390H100 110273 D420H100 110278 D450H100 110283 D480H100 110288 D510H100 110293 D540H100 110298 D570H100 110303 D600H100 110308 D630H100 110313 D660H100 110318 D700H100 110323 D750H100 110328 D800H100 110333 D850H100 110338 D900H100 110343 D1000H100 110348 D1100H100 110353 D1250H100 110358 D1400H100 110363 D1700H100 110368 Avg. Wt. .47Lb.

1/2” Pitch (H) H150 (1-1/2” Wide) Belt No. Part No. D240H150 110249 D270H150 110254 D300H150 110259 D330H150 110264 D360H150 110269 D390H150 110274 D420H150 110279 D450H150 110284 D480H150 110289 D510H150 110294 D540H150 110299 D570H150 110304 D600H150 110309 D630H150 110314 D660H150 110319 D700H150 110324 D750H150 110329 D800H150 110334 D850H150 110339 D900H150 110344 D1000H150 110349 D1100H150 110354 D1250H150 110359 D1400H150 110364 D1700H150 110369 Avg. Wt. .70Lb.

BELT SPECIFICATIONS PAGES PT10-11

H200(2” Wide) Belt No. Part No. D240H200 110250 D270H200 110255 D300H200 110260 D330H220 110565 D360H200 110270 D390H200 110275 D420H200 110280 D450H200 110285 D480H200 110290 D510H200 110295 D540H220 110300 D570H200 110305 D600H200 110310 D630H200 110315 D660H200 110320 D700H200 110325 D750H200 110330 D800H200 110335 D850H200 110340 D900H200 110345 D1000H200 110350 D1100H200 110355 D1250H200 110360 D1400H200 110365 D1700H200 110370 Avg. Wt. .94Lb.

SELECTION PAGES PT10-14

PT10-11

H300 (3” Wide) Belt No. Part No. D240H300 110251 D270H300 110256 D300H300 110261 D330H300 110266 D360H300 110271 D390H300 110276 D420H300 110281 D450H300 110269 D480H300 110291 D510H300 110296 D540H300 110301 D570H300 110306 D600H300 110311 D630H300 110316 D660H300 110321 D700H300 110326 D750H300 110331 D800H300 110336 D850H300 110341 D900H300 110346 D1000H300 110351 D1100H300 110356 D1250H300 110361 D1400H300 110366 D1700H300 110371 Avg. Wt. 1.41Lb. ENGINEERING/TECHNICAL PAGES PT10-44

Engineering

Belt Lgth. 24.0 27.0 30.0 33.0 36.0 39.0 42.0 45.0 48.0 51.0 54.0 57.0 60.0 63.0 66.0 70.0 75.0 80.0 85.0 90.0 100.0 110.0 125.0 140.0 170.0

Conveyor Components

DH Series Dual DYNA-SYNC Belts


DYNA-SYNC

SPECIFICATIONS DYNA-SYNC Belts XL Series DYNA-SYNC Belts Belt Length

HT Synchrous Belts

6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 19.0 20.0 21.0 22.0 23.0 24.0 25.0 26.0

Sprockets

XL025 Belt No. 60XL025 70XL025 80XL025 90XL025 100XL025 110XL025 120XL025 130XL025 140XL025 150XL025 160XL025 170XL025 180XL025 190XL025 200XL025 210XL025 220XL025 230XL025 240XL025 250XL025 260XL025

1/5” Pitch (XL) (1/4” Wide) XL037 Part Belt Wt. No. No. 465335 ... 60XL037 464501 ... 70XL037 464502 ... 80XL037 464503 ... 90XL037 464504 ... 100XL037 464505 ... 110XL037 464506 ... 120XL037 464507 .01 130XL037 464508 .01 140XL037 464509 .01 150XL037 464510 .01 160XL037 464511 .01 170XL037 464512 .01 180XL037 464513 .01 190XL037 464514 .01 200XL037 464515 .01 210XL037 464516 .01 220XL037 .01 230XL037 464517 464518 .01 240XL037 464519 .01 250XL037 464520 .02 260XL037

(3/8” Wide) Part No. 464521 464522 464523 464524 464525 464526 464527 464528 464529 464530 464531 464532 464533 464534 464535 464536 464537 464538 464539 464540 464541

Wt.

L Series DYNA-SYNC Belts Belt Length

Conveyor Components Engineering

12.4 15.0 18.7 21.0 22.5 24.0 25.5 27.0 28.5 30.0 32.2 34.5 36.7 39.0 42.0 45.0 48.0 51.0 54.0 60.0

Belt No. 124L050 150L050 187L050 210L050 225L050 240L050 255L050 270L050 285L050 300L050 322L050 345L050 367L050 390L050 420L050 450L050 480L050 510L050 540L050 600L050

FEATURES/BENEFITS PAGE PT10-2

L050 (1/2” Wide) Part No. 464542 464543 464544 464545 464546 464547 464548 464549 464550 464551 464552 464553 464554 464555 464556 464557 464558 464559 464560 464561

Wt. .03 .04 .05 .05 .06 .06 .06 .07 .07 .08 .08 .09 .09 .10 .11 .11 .12 .13 .14 .15

3/8” Pitch (L) L075 (3/4” Wide) Belt Part No. No. 124L075 464562 150L075 464563 187L075 464564 210L075 464565 225L075 464566 240L075 464567 255L075 464568 270L075 464569 285L075 464570 300L075 464571 322L075 464572 345L075 464573 367L075 464574 390L075 464575 420L075 464576 450L075 464577 480L075 464578 510L075 464579 540L075 464580 600L075 464581

BELT SPECIFICATIONS PAGES PT10-11

Wt. .05 .06 .07 .08 .09 .09 .10 .10 .11 .11 .12 .13 .14 .15 .16 .17 .18 .19 .21 .23

SELECTION PAGES PT10-14

PT10-12

Belt No. 124L100 150L100 187L100 210L100 225L100 240L100 255L100 270L100 285L100 300L100 322L100 345L100 367L100 390L100 420L100 450L100 480L100 510L100 540L100 600L100

L100 (1” Wide) Part No. 464582 464583 464534 464585 464586 464587 464588 464589 464590 464591 464592 464593 464594 464595 464596 464597 464598 464599 464600 464601

Wt. .06 .08 .10 .09 .11 .11 .13 .14 .14 .15 .16 .17 .19 .20 .21 .23 .24 .26 .27 .30

ENGINEERING/TECHNICAL PAGES PT10-44

... ... ... .01 .01 .01 .01 .01 .01 .01 .01 .01 .02 .02 .02 .02 .02 .02 .02 .02 .02


H Series DYNA-SYNC Belts Belt Length 24.0 27.0 30.0 33.0 36.0 39.0 42.0 45.0 48.0 51.0 54.0 57.0 60.0 63.0 66.0 70.0 75.0 80.0 85.0 90.0 100.0 110.0 125.0 140.0 170.0

H075 (3/4” Wide) Belt Part Wt. No. No. 240H075 464602 .11 270H075 464603 .12 300H075 464604 .14 330H075 464605 .14 360H075 464606 .15 390H075 464607 .18 420H075 464608 .19 450H075 464609 .20 480H075 464610 .23 510H075 464611 .23 540H075 464612 .24 570H075 464613 .26 600H075 464614 .27 630H075 464615 .29 660H075 464616 .30 700H075 464617 .32 750H075 464618 .34 800H075 464619 .36 850H075 464620 .38 900H075 464759 .41 1000H075 464760 .45 1100H075 464761 .50 1250H075 464762 .57 1400H075 464763 .63 1700H075 464764 .77

H100 (1” Wide) Belt Part Wt. No. No. 240H100 464621 .14 270H100 464622 .16 300H100 464623 .18 330H100 464624 .20 360H100 464625 .22 390H100 464626 .24 420H100 464627 .25 450H100 464628 .27 480H100 464629 .31 510H100 464630 .31 540H100 464631 .33 570H100 464632 .34 600H100 464633 .36 630H100 464634 .38 660H100 464635 .40 700H100 464636 .42 750H100 464637 .45 800H100 464638 .48 850H100 464639 .51 900H100 464640 .54 1000H100 464641 .60 1100H100 464642 .66 1250H100 464643 .75 1400H100 464644 .85 1700H100 464765 1.03

1/2” Pitch (H) H150 (1-1/2” Wide) Belt Part Wt. No. No. 240H150 464645 .22 270H150 464646 .24 300H150 464647 .27 330H150 464648 .30 360H150 464649 .33 390H150 464650 .35 420H150 464651 .38 450H150 464652 .41 480H150 464653 .46 510H150 464654 .46 540H150 464655 .49 570H150 464656 .52 600H150 464657 .54 630H150 464658 .57 660H150 464659 .60 700H150 464660 .63 750H150 464661 .68 800H150 464662 .72 850H150 464663 .77 900H150 464766 .82 1000H150 464767 .91 1100H150 464768 1.00 1250H150 464769 1.13 1400H150 464770 1.27 1700H150 464771 1.54

H200 (2” Wide) Belt Part Wt. No. No. 240H200 464772 .29 270H200 464773 .33 300H200 464774 .36 330H200 464775 .40 360H200 464664 .43 390H200 464665 .47 420H200 464666 .51 450H200 464667 .54 480H200 464668 .62 510H200 464669 .62 540H200 464670 .65 570H200 464671 .69 600H200 464672 .72 630H200 464673 .76 660H200 464674 .80 700H200 464675 .85 750H200 464676 .91 800H200 464677 .97 850H200 464678 1.03 900H200 464679 1.09 1000H200 464680 1.21 1100H200 464681 1.33 1250H200 464682 1.51 1400H200 464776 1.69 1700H200 464777 2.05

H300 (3” Wide) Belt Part Wt. No. No. 240H300 464778 .43 270H300 464779 .49 300H300 464780 .54 330H300 464781 .60 360H300 464736 .65 390H300 464737 .71 420H300 464738 .76 450H300 464739 .81 480H300 464740 .92 510H300 464741 .92 540H300 464683 .98 570H300 464684 1.03 600H300 464685 1.09 630H300 464686 1.14 660H300 464687 1.20 700H300 464688 1.27 750H300 464689 1.36 800H300 464742 1.45 850H300 464743 1.54 900H300 464744 1.63 1000H300 464745 1.81 1100H300 464746 1.99 1250H300 464747 2.26 1400H300 464748 2.54 1700H300 464749 3.08

Sprockets

DYNA-SYNC Belts

HT Synchrous Belts

DYNA-SYNC

SPECIFICATIONS

XH Series DYNA-SYNC Belts

50.7 56.0 63.0 70.0 77.0 84.0 98.0 112.0 126.0 140.0 154.0 175.0

(2” Wide) Part Wt. No. 464690 1.77 464691 1.95 464692 2.20 464693 2.33 464694 2.69 464695 2.79 464696 3.42 464697 3.72 464698 4.19 464699 4.65 464700 5.12 464701 5.82

7/8” Pitch (XH) XH300 (3” Wide) Belt Part No. No. 507XH300 464702 560XH300 464703 630XH300 464704 700XH300 464705 770XH300 464706 840XH300 464707 980XH300 464708 1120XH300 464709 1260XH300 464710 1400XH300 464711 1540XH300 464712 1750XH300 464713

Wt. 2.66 2.93 3.30 3.49 3.49 4.19 5.13 5.58 6.28 6.98 7.68 8.73

XH400 Belt No. 507XH400 560XH400 630XH400 700XH400 770XH400 840XH400 980XH400 1120XH400 1260XH400 1400XH400 1540XH400 1750XH400

(4” Wide) Part No. 464750 464751 464752 464753 464754 464755 464756 464757 464758 464782 464783 464784

Wt. 3.54 3.91 4.40 4.65 4.65 5.58 6.84 7.45 8.38 9.31 10.2 10.6

Conveyor Components

Belt Length

XH200 Belt No. 507XH200 560XH200 630XH200 700XH200 770XH200 840XH200 980XH200 1120XH200 1260XH200 1400XH200 1540XH200 1750XH200

XXH Series DYNA-SYNC Belts

70.0 80.0 90.0 100.0 120.0 140.0 160.0 180.0

XXH200 (2” Wide) Belt Part No. No. 700XXH200 465301 800XXH200 465305 900XXH200 465309 1000XXH200 465313 1200XXH200 465337 1400XXH200 465323 1600XXH200 465324 1800XXH200 465338

FEATURES/BENEFITS PAGE PT10-2

Wt. 3.23 3.70 4.38 4.87 5.54 6.47 7.39 8.32

1-1/4” Pitch (XXH) XXH300 (3” Wide) XXH400 (4” Wide) Belt Part Belt Part Wt. No. No. No. No. 700XXH300 465302 4.85 700XXH400 465303 800XXH300 465306 5.54 800XXH400 465307 900XXH300 465310 6.58 900XXH400 465311 1000XXH300 465314 7.31 1000XXH400 465315 1200XXH300 465317 8.32 1200XXH400 465318 1400XXH300 465320 9.70 1400XXH400 465321 1600XXH300 465325 11.1 1600XXH400 465326 1800XXH300 465329 12.5 1800XXH400 465330 BELT SPECIFICATIONS PAGES PT10-11

SELECTION PAGES PT10-14

PT10-13

Wt. 6.47 7.39 8.77 9.74 11.1 12.9 14.8 16.6

XXH500 (5” Wide) Belt Part No. No. 700XXH500 465304 800XXH500 465308 900XXH500 465312 1000XXH500 465316 1200XXH500 465319 1400XXH500 465322 1600XXH500 465327 1800XXH500 465331

Wt. 8.09 9.24 11.0 12.2 13.9 16.2 18.5 20.8

ENGINEERING/TECHNICAL PAGES PT10-44

Engineering

Belt Length


DYNA-SYNC

SELECTION DYNA-SYNC Drives USING STANDARD MOTOR SPEEDS Step 1–Determine Service Factor from steps on page PT10-16. Step 2–Compute Design HP. Multiply normal running HP required or nameplate rating by service factor obtained in Step 1.

HT Synchrous Belts

Step 3–Choose Belt Section. Using Table 1, read up from design HP figure obtained in Step 2 and over from the RPM of faster shaft. This intersection indicates belt section.

Sprockets

Step 4–Select the Drive, a). Using the belt section from Step 3, refer to Selection Tables beginning on page PT10-18. b). Under appropriate standard full-load motor RPM, find the driven RPM nearest to the desired speed. Trace right to columns headed “Pulley Combination.” If more than one is listed, the combination with the largest pulleys usually will offer the best belt life. (Note that one pulley must be flanged on all drives. If center distance exceeds 8 times P.D. of small pulley or shafts are vertical or inclined, both must be flanged.) c). On

same line trace right to the figure nearest the desired center distance and at top of column note belt number. d). Trace back on same line to appropriate column under heading “HP for a 1” Belt...” Divide the design HP obtained in Step 2 by the HP thus found in table. (Divide this value by Teeth in Mesh (T.I.M.) factor when applicable.) The result is the Belt Width Factor. Refer to table below right hand selection table to determine belt width required. If width shown is not stock go to next stock width listed. Add belt code, from table, to belt number found in Step 4c. (If wider stock belt is not shown in table, redesign drive to next larger pitch.) To check drive calculation: HP for a 1” Wide Belt x Belt Width factor x Teeth in Mesh factor = Actual HP rating of the drive. If actual rating is equal to or greater than Design HP, selection is O.K. NOTE: Good practice dictates that shaft and bushing system (or alternate shaft mounting method) be verified for adequate rating.

Conveyor Components Engineering FEATURES/BENEFITS PAGE PT10-2

PULLEY SPECIFICATIONS PAGES PT10-3

BELT SPECIFICATIONS PAGES PT10-11

PT10-14

ENGINEERING/TECHNICAL PAGES PT10-44


USING STANDARD MOTOR SPEEDS EXAMPLE OF SELECTION

combinations are listed. The 28H driver/120H driven is preferred. On the same line the nearest center distance to 25” is 25.45”. Note the 900 H belt at top of column. Tracing back on the same line, under 1160 RPM, the “HP for a 1” Belt” is 5.68. 11 design HP 5.68 = 1.937 Belt Width Factor. Belt Width Table indicates a 2” wide belt is required. Add code number 200 to belt and pulley number and order the following: (1) TL28H200 DYNASYNC Pulley, (1) 2012 Taper-Lock (1) TL120H200 pulley. (1) TAPER-LOCK 3020 bushing. (1) 900H200 DYNA-SYNC Belt. To facilitate delivery, order by part numbers listed in Pulley, Bushing and Belt sections of this catalog.

Select a drive for a 3 cylinder reciprocating compressor to run 8 hours a day at about 270 RPM and to be driven by a 5 HP, 1160 RPM Design B squirrel cage motor. Centers are about 25”. Step 1–Service Factor from page PT10-16 is 2.2. Step 2–Design HP = 5 x 2.2 = 11 HP. Step 3–An “H” Cross Section is shown in Table 1 when reading to the right of 1160 RPM of faster shaft and up from 11 design HP. Step 4–The H-Section drive tables begin on page PT10-30. On page PT10-34, the nearest driven speed for a 1160 RPM motor is 271 RPM. Two possible pulley

DYNA-SYNC

DYNA-SYNC Drives

HT Synchrous Belts

SELECTION

Table 1 – Synchronous Cross Section Selection Chart Sprockets

20,000 10,000

3,450 2,500 1,750 1,500 1,160 870 690 515 500 400 300

XL L

H XH XXH

200 100 .02 .03

.05

0.1

0.2 0.3 0.5

1

2

3

5

10

20 30

50

100

200 300

Engineering

.01

Conveyor Components

RPM of Faster Shaft

5,000

FEATURES/BENEFITS PAGE PT10-2

PULLEY SPECIFICATIONS PAGES PT10-3

BELT SPECIFICATIONS PAGES PT10-11

PT10-15

ENGINEERING/TECHNICAL PAGES PT10-14


DYNA-SYNC

SELECTION Service Factor To determine the service factor for a DYNA-SYNC drive follow the three steps below.

Table 4 – Service Factors* Application

Step 1. Determine the class of Driver from Table 2 below. Step 2. Use Class of Driver and Type of Application in Table 4 at right to find the tentative service factor. HT Synchrous Belts

Step 3. Add the Additional Service Factor, when applicable, from Table 3 at bottom of page to the tentative service factor from Step 2 to determine the service factor for the application. Table 2 – Class of Driver

Sprockets Conveyor Components

Driver Class I Class II Class III A-C Electric Motors, Single Phase. . . . . ........ ........ All Squirrel Cage, NEMA Design A, 3500 RPM . . . . 40 HP up 30 HP or less ........ 1750 RPM . . . . 100 HP up 5 to 75 HP 3 HP or less 1160 RPM . . . . 15 HP up 10 HP or less ........ 870 RPM . . . . . 5 HP up 3 HP or less ........ NEMA Design B, 3500 RPM . . . . . . . . . . . . 5 HP up 3 HP or less 1750 RPM . . . . . . . . . . . . 5 HP up 3 HP or less 1160 RPM . . . . . . . . . . . . 5 HP up 3 HP or less 870 RPM . . . . . . . . . . . . . 2 HP up 1-1/2 HP or less NEMA Design C, 1750 RPM . . . . . . . . . . . . 15 HP up 10 HP or less 1160 RPM . . . . . . . . . . . . 7-1/2 HP up 5 HP or less 870 RPM . . . . . . . . . . . . . All ........ NEMA Design D . . . . . . . . . ........ All NEMA Design F . All ........ ........ Wound Rotor, . . . . . . . . . . . 1750 RPM . . . . . . . . . . . . 20 HP 15 HP or less 1160 RPM . . . . . . . . . . . . 15 HP 10 HP or less 870 RPM . . . . . . . . . . . . . 7-1/2 HP 5 HP or less Synchronous . . . . . . . . . . . . Norm. Torque High Torque D-C Electric Motors Shunt Compound Series Engines-Int. Comb 8 Cyl. up 6 Cyl 4 Cyl. or less Hydraulic Motors . . ........ ........ All Line Shafts . . . . . . . ........ ........ All

Table 3 – Additional Service Factors† Condition 24 hour continuous operation . . . . . . . . . . . . . . . . Use of an idler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Intermittent or seasonal operation . . . . . . . . . . . Speed up drive: 1 to 1.24 ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.25 to 1.74 ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.75 to 2.49 ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.50 to 3.49 ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . Over 3.49 ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Additional Factor 0.2 0.2 ◊ 0.0 0.1 0.2 0.3 0.4

Engineering

†Additional service factors other than listed here are required for unusual condition such as torque reversal, heavy shock, when current to motor is reversed to either stop the motor rapidly or to run it in opposite direction, or when a brake is to be used. For such applications consult factory. ◊ Subtract 0.2 from tentative service factor. FEATURES/BENEFITS PAGE PT10-2

AGITATORS, MIXERS (Paddle or Propeller) Liquid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Semi-liquid . . . . . . . . . . . . . . . . . . . . . . . . . BAKERY MACHINERY DOUGH MIXERS . BRICK AND CLAY MACHINERY Augers, Mixers, Granulators . . . . . . . . . . . Pug Mills . . . . . . . . . . . . . . . . . . . . . . . . . . . CENTRIFUGES . . . . . . . . . . . . . . . . . . . . . . . COMPRESSORS Reciprocating . . . . . . . . . . . . . . . . . . . . . . . Centrifugal . . . . . . . . . . . . . . . . . . . . . . . . . . CONVEYORS Light-Package Belt, oven . . . . . . . . . . . . . Belt, Ore, Coal, Sand . . . . . . . . . . . . . . . . Apron, Bucket, Elevator, Pan . . . . . . . . . . Flight, Screw . . . . . . . . . . . . . . . . . . . . . . . . FANS, BLOWERS Centrifugal, Induced Draft Exhausters . . Propeller, Mine fans, Positive Blowers . . GENERATORS AND EXCITERS . . . . . . . . HAMMER MILLS . . . . . . . . . . . . . . . . . . . . . . LAUNDRY MACHINERY General . . . . . . . . . . . . . . . . . . . . . . . . . . . . Extractors, Washers . . . . . . . . . . . . . . . . . LINE SHAFTS . . . . . . . . . . . . . . . . . . . . . . . . MACHINE TOOLS Drill Presses, Lathes, Screw Machines . Boring Mills, Grinders . . . . . . . . . . . . . . . . Milling Machines, Shapers . . . . . . . . . . . . MILLS Ball, Rod, Pebble. etc. . . . . . . . . . . . . . . . . PAPER MACHINERY Agitators, Calenders, Dryers . . . . . . . . . . Beaters, Jordans, Nash Pumps, Pulpers PRINTING MACHINERY Presses: Newspaper, Rotary, Embossing, Flat Bed, Magazine; Linotype Machines; Cutters; Folders . . . . . . . . . . . PUMPS Centrifugal, Gear, Rotary, Pipeline . . . . . Reciprocating . . . . . . . . . . . . . . . . . . . . . . . RUBBER PLANT MACHINERY . . . . . . . . . SAW MILL MACHINERY . . . . . . . . . . . . . . . SCREENS Vibrating (Shakers) . . . . . . . . . . . . . . . . . . Drum, Conical . . . . . . . . . . . . . . . . . . . . . . TEXTILE MACHINERY Looms, Spinning Frames, Twisters . . . . . Wrappers, Reels . . . . . . . . . . . . . . . . . . . . WOODWORKING MACHINERY Lathes, Band Saws . . . . . . . . . . . . . . . . . . Jointers, Circular Saws, Planers . . . . . . .

PULLEY SPECIFICATIONS PAGES PT10-3

BELT SPECIFICATIONS PAGES PT10-11

PT10-16

I

Class II

III

1.4 1.5 1.4

1.6 1.7 1.6

1.8 1.9 1.8

1.5 1.8 1.8

1.7 2.0 1.9

1.9 2.2 ...

2.0 1.8

2.2 1.7

2.4 1.8

1.3 1.8 1.7 1.7

1.5 1.7 1.8 1.9

1.7 1.8 1.9 2.0

1.8 1.8 1.6 1.7

1.8 2.0 1.8 1.9

2.0 2.2 2.0 2.1

1.5 1.6 1.5

1.6 1.8 1.7

1.7 2.0 1.9

1.4 1.5 1.5

1.6 1.7 1.7

1.8 1.9 1.9

...

2.2

2.5

1.4 1.7

1.6 1.9

1.8 2.1

1.4

1.6

1.8

1.5 2.0 1.6 1.6

1.7 2.2 1.8 1.8

1.9 2.4 2.0 2.0

1.5 1.4

1.7 1.5

... ...

1.6 1.5

1.8 1.7

2.0 ...

1.3 1.4

1.4 1.6

... ...

ENGINEERING/TECHNICAL PAGES PT10-44


FOR SPEEDS OTHER THAN STANDARD MOTOR SPEEDS AND SPEED-UP DRIVES

Step 5–Select the Drive. a.) Using the belt section obtained in Step 4, refer to Selection Tables beginning on PT10-18. b.) Read down ratio column to the value nearest to one calculated in Step 1. Trace right to columns headed “Pulley Combinations.” If more than one is listed, the combination with the largest pulleys usually will offer the best belt life. (Note that one pulley must be flanged on all drives. If center distance exceeds 8 times P.D. of small pulley or shafts are vertical or inclined, both must be flanged.) c.) On the same line trace right to figure nearest the desired center distance and at top of column note belt number. d.) Now go to the HP Table for the appropriate belt section. Reading to the right of the speed of the faster pulley and down from the pulley size, the HP figure for a 1” belt will appear. Divide the design HP from Step 3 by the HP thus found in table. (Divide this value by Teeth in Mesh factor, when applicable.) The result is the Belt Width Factor. Refer to table below the HP Table to determine belt width factor required. If width shown is not in stock go to next stock width listed. Add belt code, from table, to belt number found in Step 5c. (If wider stock belt is not shown in table, redesign drive to next larger pitch). EXAMPLE OF SELECTION A printing machine embossing roll runs at 426 RPM, powered from an 800 RPM line shaft. The roll required 7 HP. Machine runs 8-10 hrs. a day. Center distance is approx. 20". 800 Step 1–Speed Ratio = = 1.88 426 Step 2–Service Factor = 1.8 Step 3–Design HP = 7 x 1.8 = 12.6 Step 4–Belt Selection from Table 1 = H

FEATURES/BENEFITS PAGE PT10-2

(1) TL32H300 DYNA-SYNC Pulley, (1) 2517 TAPER-LOCK bushing (Check to see if bushing will fit equipment shafts). (1) TL60H300 Pulley. (1) 3020 bushing (1) 630H300 DYNA-SYNC Belt. To facilitate delivery, use part numbers listed in Pulley, Bushing and Belt sections of this catalog. Example of a Speed-Up Drive Select a drive for a continuous duty liquid agitator to run at about 2000 RPM and to be driven by a 10 HP, 1750 RPM squirrel cage motor Centers are about 10”.

Sprockets

Step 4–Using Table 1 on page PT10-15 read up from design HP obtained in Step 3 and over from RPM of faster shaft. This intersection indicates belt section.

Step 1–Speed ratio is 2000 ÷ 1750 = 1.14. Step 2–Service factor from page PT10-3 is 1.8 Step 3–Design HP= 10 x 1.8= 18 HP. Step 4–An “H” Cross Section is shown in Table 1 when reading to the right of 2000 RPM and up from 18 design HP. Step 5–Speed ratio calculated in Step 1 appears in Selection Table on page PT10-30. Two possible pulley combinations are listed. The 28H driver/32H driven is preferred. In a Speed-Up Drive, the 28H becomes the driven, the 32H, the driver. On the same line the nearest center distance to 10” is 10.5. Note the 360H belt at top of column. Referring to HP table on page PT10-42, the rating for a 1” wide belt is shown as 9.60 for a 28H pulley at 2000 RPM. 18 design HP ÷ 9.601.875 Belt Width Factor Belt Width Table indicates a 2” wide belt is required. Add code number 200 to belt and pulley number and order the following: (1) TL32H200 DYNA-SYNC Pulley, (1) 2517 TAPER-LOCK Bushing. (Check to see if bushings will fit equipment shafts). (1) TL28H200 Pulley, (1) 2012 bushing (with 2, max. bore). (1) 360H200 DYNA-SYNC belt.

PULLEY SPECIFICATIONS PAGES PT10-3

BELT SPECIFICATIONS PAGES PT10-11

PT10-17

ENGINEERING/TECHNICAL PAGES PT10-14

Conveyor Components

Step 3–Calculate Design HP. Multiply normal running HP required or nameplate rating by service factor obtained in Step 2.

Step 5–The H Section Drive Tables begin on page PT10-30. The ratio of 1.88 obtained in Step 1 is found on page PT10-32. Two pulley combinations are listed. The 32H driver /60H driven is preferred. On the same line the nearest center distance to 20” is 19.88. Note the 630H belt at top of column. Refer to H section HP Tables on page PT10-42. Opposite 800 RPM of faster shaft and under 32H pulley, the HP 4.50 = 2.8. This is the belt width factor. Referring to the H belt width table a 3” wide belt is stock. Add the 300 Code Width to the pulley and belt numbers and order the following:

Engineering

For Speeds Other than Standard Motor Speeds: Driver RPM Step 1–Calculate Speed Ratio = Driven RPM Step 2–Determine Service Factor from steps on page PT10-16.

DYNA-SYNC

DYNA-SYNC Drives

HT Synchrous Belts

SELECTION


DYNA-SYNC

SELECTION

XL Stock Drive Selections Driven Speeds for Motor Speeds of

HT Synchrous Belts Sprockets Conveyor Components

3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3341 3333 3281 3281 3267 3267 3208 3208 3182 3150 3111 3063 3063 3063 3000 3000 3000 2917 2917 2917 2864 2800 2800 2800 2750 2750 2722 2722 2667 2625 2625 2625 2625 2625 2625 2567 2567 2545 2500 2500 2500 2450 2450 2450 2406 2406

1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1675 1667 1641 1641 1634 1634 1604 1604 1591 1575 1556 1532 1532 1532 1500 1500 1500 1458 1458 1458 1432 1400 1400 1400 1375 1375 1361 1361 1333 1313 1313 1313 1313 1313 1313 1283 1283 1273 1250 1250 1250 1225 1225 1225 1203 1203

1160 1160 1160 1160 1160 1160 1160 1160 1160 1160 1160 1160 1160 1107 1105 1088 1088 1083 1083 1063 1063 1055 1044 1031 1015 1015 1015 994 994 994 967 967 967 949 928 928 928 911 911 902 902 884 870 870 870 870 870 870 851 851 844 829 829 829 812 812 812 798 798

Speed Ratio 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.05 1.05 1.07 1.07 1.07 1.07 1.09 1.09 1.10 1.11 1.13 1.14 1.14 1.14 1.17 1.17 1.17 1.20 1.20 1.20 1.22 1.25 1.25 1.25 1.27 1.27 1.29 1.29 1.31 1.33 1.33 1.33 1.33 1.33 1.33 1.36 1.36 1.38 1.40 1.40 1.40 1.43 1.43 1.43 1.45 1.45

Pulley Combination Driver Driven No. of Pitch No. of Pitch Teeth Diam. Teeth Diam. 30XL 1.910 30XL 1.910 28XL 1.783 28XL 1.783 24XL 1.528 24XL 1.528 22XL 1.401 22XL 1.401 21XL 1.337 21XL 1.337 20XL 1.273 20XL 1.273 18XL 1.146 18XL 1.146 16XL 1.019 16XL 1.019 15XL .955 15XL .955 14XL .891 14XL .891 12XL .764 12XL .764 11XL .700 11XL .700 21XL 1.337 22XL 1.401 20XL 1.273 21XL 1.337 30XL 1.910 32XL 2.037 15XL .955 16XL 1.019 28XL 1.783 30XL 1.910 14XL .891 15XL .955 22XL 1.401 24XL 1.528 11XL .700 12XL .764 20XL 1.273 22XL 1.401 18XL 1.146 20XL 1.273 16XL 1.019 18XL 1.146 28XL 1.783 32XL 2.037 21XL 1.337 24XL 1.528 14XL .891 16XL 1.019 24XL 1.528 28XL 1.783 18XL 1.146 21XL 1.337 12XL .764 14XL .891 30XL 1.910 36XL 2.292 20XL 1.273 24XL 1.528 15XL .955 18XL 1.146 18XL 1.146 22XL 1.401 24XL 1.528 30XL 1.910 16XL 1.019 20XL 1.273 12XL .764 15XL .955 22XL 1.401 28XL 1.783 11XL .700 14XL .891 28XL 1.783 36XL 2.292 14XL .891 18XL 1.146 16XL 1.019 21XL 1.337 30XL 1.910 40XL 2.546 24XL 1.528 32XL 2.037 21XL 1.337 28XL 1.783 18XL 1.146 24XL 1.528 15XL .955 20XL 1.273 12XL .764 16XL 1.019 22XL 1.401 30XL 1.910 11XL .700 15XL .955 16XL 1.019 22XL 1.401 30XL 1.910 42XL 2.674 20XL 1.273 28XL 1.783 15XL .955 21XL 1.337 28XL 1.783 40XL 2.546 21XL 1.337 30XL 1.910 14XL .891 20XL 1.273 22XL 1.401 32XL 2.037 11XL .700 16XL 1.019

HP for a 1 Wide Belt for Motor Speeds of Δ 3500 2.11 1.98 1.71 1.57 1.49 1.42 1.28 1.15 1.07 1.00 .86 .79◊ 1.49 1.42 2.11 1.07 1.98 1.00 1.57 .79◊ 1.42 1.28 1.15 1.98 1.49 1.00 1.71 1.28 .86 2.11 1.42 1.07 1.28 1.71 1.15 .86 1.57 .79◊ 1.98 1.00 1.15 2.11 1.71 1.49 1.28 1.07 .86 1.57 .79◊ 1.15 2.11 1.42 1.07 1.98 1.49 1.00 1.57 .79◊

Engineering

Δ HP ratings are for conventional speed-reduction drives. For Speed-Up Drives refer to page PT10-17. ◊ Pulley Diameter is below recommended minimum. A reduction in belt life should be expected. Suggest alternate drive selection, whenever possible.

FEATURES/BENEFITS PAGE PT10-2

PULLEY SPECIFICATIONS PAGES PT10-3

1750 1.07 1.00 .86 .79 .75 .72 .64 .58 .53 .50 .43 .39 .75 .72 1.07 .53 1.00 .50 .79 .39 .72 .64 .58 1.00 .75 .50 .86 .64 .43 1.07 .72 .53 .64 .86 .58 .43 .79 .39 1.00 .50 .58 1.07 .86 .75 .64 .53 .43 .79 .38 .58 1.07 .72 .53 1.00 .75 .50 .79 .39

1160 .71 .66 .56 .52 .50 .46 .42 .38 .36 .33 .28 .26 .50 .46 .71 .36 .66 .33 .52 .26 .46 .42 .38 .66 .50 .33 .56 .42 .28 .71 .46 .36 .42 .56 .38 .28 .52 .26 .66 .33 .38 .71 .56 .50 .42 .36 .28 .52 .26 .38 .71 .46 .36 .66 .50 .33 .52 .26

Nominal C.D. Using DYNA-SYNC Belts 60XL .... .... .... .... .... .... .... 1.40 1.50 1.60 1.80 1.90† .... .... .... 1.45 .... 1.55 .... 1.85† .... .... .... .... .... 1.49 .... .... 1.69† .... .... 1.34 .... .... .... 1.6† .... 1.7† .... 1.39 .... .... .... .... .... .... 1.59† .... 1.69† .... .... .... .... .... .... .... .... 1.64†

80XL .... .... .... 1.80 1.90 2.00 2.20 2.40 2.50 2.60 2.80 2.90† 1.85 1.95 .... 2.45 .... 2.55 .... 2.85† 1.89 2.09 2.29 .... 1.74 2.49 .... 2.04 2.69† .... 1.79 2.34 1.99 .... 2.19 2.64† .... 2.74† .... 2.39 2.14 .... 1.89 .... .... 2.24 2.59† .... 2.69† 2.09 .... .... 2.19 .... .... 2.29 .... 2.64†

90XL .... .... 2.10 2.30 2.40 2.50 2.70 2.90 3.00 3.10 3.30 3.40† 2.35 2.45 .... 2.95 .... 3.05 2.19 3.35† 2.39 2.59 2.79 .... 2.24 2.99 .... 2.54 3.19† .... 2.29 2.84 2.49 .... 2.69 3.14† 1.99 3.24† .... 2.89 2.64 .... .... 2.03 2.39 2.74 3.09† .... 3.19† 2.59 .... 2.08 2.69 .... 1.92 2.79 .... 3.14†

100XL .... 2.20 2.60 2.80 2.90 3.00 3.20 3.40 3.50 3.60 3.80 3.90† 2.85 2.95 .... 3.45 2.09 3.55 2.69 3.85† 2.89 3.09 3.29 .... 2.74 3.49 2.39 3.04 3.69† .... 2.79 3.34 2.99 2.29 3.19 3.64† 2.49 3.74† .... 3.39 3.14 .... 2.18 2.54 2.89 3.24 3.59† 2.38 3.69† 3.09 .... 2.58 3.19 .... 2.43 3.29 2.27 3.64†

110XL 2.50 2.70 3.10 3.30 3.40 3.50 3.70 3.90 4.00 4.10 4.30 4.40† 3.35 3.45 2.39 3.95 2.59 4.05 3.19 4.35† 3.39 3.59 3.79 2.49 3.24 4.00 2.89 3.54 4.20† .... 3.29 3.84 3.49 2.79 3.69 4.14† 2.99 4.24† 2.28 3.89 3.64 .... 2.68 3.04 3.39 3.74 4.09† 2.88 4.19† 3.59 .... 3.09 3.69 .... 2.93 3.79 2.78 4.14†

† See Teeth in Mesh table on opposite page

BELT SPECIFICATIONS PAGES PT10-11

PT10-18

70XL .... .... .... .... .... .... 1.70 1.90 2.00 2.10 2.30 2.40{ .... .... .... 1.95 .... 2.05 .... 2.35† .... 1.59 1.79 .... .... 1.99 .... 1.54 2.19† .... .... 1.84 .... .... 1.69 2.14† .... 2.24† .... 1.89 1.64 .... .... .... .... 1.74 2.09† .... 2.19† 1.58 1.68 .... .... .... .... 1.79 .... 2.14†

ENGINEERING/TECHNICAL PAGES PT10-44


DYNA-SYNC

SELECTION

XL Stock Drive Selections 140XL 4.00 4.20 4.60 4.80 4.90 5.00 5.20 5.40 5.50 5.60 5.80 5.90† 4.85 4.95 3.89 5.45 4.10 5.55 4.70 5.85† 4.90 5.10 5.30 3.99 4.74 5.50 4.39 5.04 5.70{† 3.69 4.79 5.34 4.99 4.29 5.19 5.64† 4.49 5.74† 3.79 5.39 5.14 3.48 4.19 4.54 4.89 5.24 5.59† 4.39 5.89† 5.09 3.37 4.59 5.19 3.58 4.44 5.29 4.28 5.64†

150XL 4.50 4.70 5.10 5.30 5.40 5.50 5.70 5.90 6.00 6.10 6.30 6.40† 5.35 5.45 4.40 5.95 4.60 6.05 5.20 6.35† 5.40 5.60 5.80 4.49 5.24 6.00 4.89 5.54 6.20† 4.19 5.29 5.84 5.49 4.79 5.69 6.14† 4.99 6.24† 4.29 5.89 5.64 3.98 4.69 5.04 5.39 5.74 6.09† 4.89 6.19† 5.59 3.88 5.09 5.69 4.08 4.94 5.79 4.78 6.14†

160XL 5.00 5.20 5.60 5.80 5.90 6.00 6.20 6.40 6.50 6.60 6.80 6.90† 5.85 5.95 4.90 6.45 5.10 6.55 5.70 6.85† 5.90 6.10 6.30 4.99 5.74 6.50 5.39 6.04 6.70† 4.69 5.79 6.34 5.99 5.29 6.19 6.64† 5.49 6.74† 4.79 6.39 6.14 4.48 5.19 5.54 5.89 6.24 6.59† 5.39 6.69† 6.09 4.38 5.59 6.19 4.58 5.44 6.29 5.29 6.64†

170XL 5.50 5.70 6.10 6.30 6.40 6.50 6.70 6.90 7.00 7.10 7.30 7.40† 6.35 6.45 5.40 6.95 5.60 7.05 6.20 7.35† 6.40 6.60 6.80 5.49 6.24 7.00 5.89 6.54 7.20† 5.19 6.29 6.84 6.49 5.79 6.69 7.14† 5.99 7.24† 5.29 6.89 6.64 4.99 5.69 6.04 6.39 6.74 7.09† 5.89 7.19† 6.59 4.88 6.09 6.69 5.08 5.94 6.79 5.79 7.14†

180XL 6.00 6.20 6.60 6.80 6.90 7.00 7.20 7.40 7.50 7.60 7.80 7.90† 6.85 6.95 5.90 7.45 6.10 7.55 6.70 7.85† 6.90 7.10 7.30 5.99 6.74 7.50 6.39 7.04 7.70† 5.69 6.79 7.34 6.99 6.29 7.19 7.64† 6.49 7.74† 5.79 7.39 7.14 5.49 6.19 6.54 6.89 7.24 7.59† 6.39 7.69† 7.09 5.38 6.59 7.19 5.58 6.44 7.29 6.29 7.64†

190XL 6.50 6.70 7.10 7.30 7.40 7.50 7.70 7.90 8.00 8.10 8.30 8.40† 7.35 7.45 6.40 7.95 6.60 8.05 7.20 8.35† 7.40 7.60 7.80 6.49 7.24 8.00 6.89 7.54 8.20† 6.19 7.29 7.84 7.49 6.79 7.69 8.14† 6.99 8.24† 6.29 7.89 7.64 5.99 6.69 7.04 7.39 8.24 8.09† 6.89 8.19† 7.59 5.88 7.09 7.69 6.08 6.94 7.79 6.79 8.14†

200XL 7.00 7.20 7.60 7.80 7.90 8.00 8.20 8.40 8.50 8.60 8.60 8.90† 7.85 7.95 6.90 8.45 7.10 8.55 7.70 8.85† 7.90 8.10 8.30 6.99 7.74 8.50 7.39 8.04 8.70† 6.69 7.79 8.34 7.99 7.29 8.19 8.64† 7.49 8.74† 6.79 8.39 8.14 6.49 7.19 7.54 7.89 8.24 8.59† 7.39 8.69† 8.09 6.38 7.59 8.19 6.58 7.44 8.29 7.29 8.64†

210XL 7.50 7.70 8.10 8.30 8.40 8.50 8.70 8.90 9.00 9.10 9.30 9.40† 8.35 8.45 7.40 8.95 7.60 9.05 8.20 9.35† 8.40 8.60 8.80 7.49 8.24 9.00 7.89 8.54 9.20† 7.19 8.29 8.84 8.49 7.79 8.69 9.15† 7.99 9.25† 7.29 8.89 8.64 6.99 7.69 8.04 8.39 8.74 9.09† 7.89 9.19† 8.59 6.88 8.09 8.69 7.09 7.94 8.79 7.79 9.14†

220XL 8.00 6.20 6.60 8.80 8.90 9.00 9.20 9.40 9.50 9.60 9.80 9.90† 8.85 8.95 7.90 9.45 8.10 9.55 8.70 9.85† 8.90 9.10 9.30 7.99 8.74 9.50 8.39 9.05 9.70† 7.69 8.79 9.35 8.99 8.29 9.19 9.65† 8.49 9.75† 7.79 9.39 9.14 7.49 8.19 8.54 8.89 9.24 9.59† 8.39 9.69† 9.09 7.39 8.59 9.19 7.59 8.44 9.29 8.29 9.64†

230XL 8.50 8.70 9.10 9.30 9.40 9.50 9.70 9.90 10.00 10.10 10.30 10.40† 9.35 9.45 8.40 9.95 8.60 10.05 9.20 10.35† 9.40 9.60 9.80 8.49 9.25 10.00 8.89 9.55 10.20† 8.19 9.29 9.85 9.49 8.79 9.69 10.15† 8.99 10.25† 8.29 9.89 9.64 7.99 8.69 9.04 9.39 9.74 10.09† 8.89 10.19† 9.59 7.89 9.09 9.69 8.09 8.94 9.79 8.79 10.14†

240XL 9.00 9.20 9.60 9.80 9.90 10.00 10.20 10.40 10.50 10.60 10.80 10.90† 9.85 9.95 8.99 10.45 9.10 10.55 9.70 10.85† 9.90 10.10 10.30 8.99 9.75 10.50 9.39 10.05 10.70† 8.69 9.79 10.35 9.99 9.29 10.19 10.65† 9.49 10.75† 8.79 10.39 10.14 8.49 9.19 9.54 9.89 10.24 10.59† 9.39 10.69† 10.09 8.39 9.59 10.19 8.59 9.44 10.29 9.29 10.64†

250XL 9.50 9.70 10.10 10.30 10.40 10.50 10.70 10.90 11.00 11.10 11.30 11.40† 10.35 10.45 9.40 10.95 9.80 11.05 10.20 11.35† 10.40 10.60 10.80 9.49 10.25 11.00 9.89 10.55 11.20† 9.19 10.29 10.85 10.49 9.79 10.89 11.15† 9.99 11.25† 9.29 10.69 10.64 8.99 9.69 10.04 10.39 10.74 11.09† 9.89 11.19† 10.59 8.69 10.09 10.69 9.09 9.94 10.79 9.79 11.14†

260XL 10.00 10.20 10.60 10.80 10.90 11.00 11.20 11.40 11.50 11.60 11.80 11.90† 10.85 10.95 9.90 11.45 10.10 11.55 10.70 11.85† 10.90 11.10 11.30 9.99 10.75 11.50 10.39 11.05 11.70† 9.69 10.79 11.35 10.99 10.29 11.19 11.65† 10.49 11.75† 9.79 11.39 11.14 9.49 10.19 10.54 10.89 11.24 11.59† 10.39 11.69† 11.09 9.39 10.59 11.19 9.59 10.44 11.29 10.29 11.64†

Sprockets

130XL 3.50 3.70 4.10 4.30 4.40 4.50 4.70 4.90 5.00 5.10 5.30 5.40† 4.35 4.45 3.39 4.95 3.59 5.05 4.20 5.35† 4.40 4.60 4.80 3.49 4.24 5.00 3.89 4.54 5.20† 3.19 4.29 4.84 4.49 3.79 4.69 5.14† 3.99 5.24† 3.29 4.89 4.64 2.98 3.69 4.04 4.39 4.74 5.09† 3.89 5.19† 4.59 2.87 4.09 4.69 3.07 3.84 4.79 3.78 5.14†

Conveyor Components

120XL 3.00 3.20 3.60 3.80 3.90 4.00 4.20 4.40 4.50 4.60 4.80 4.90† 3.85 3.95 2.89 4.45 3.09 4.55 3.69 4.85† 3.89 4.10 4.30 2.99 3.74 4.50 3.39 4.04 4.70† 2.69 3.79 4.34 3.99 3.29 4.19 4.64† 3.49 4.74† 2.78 4.39 4.14 2.48 3.19 3.54 3.89 4.24 4.59† 3.39 4.69† 4.09 .... 3.59 4.19 2.57 3.43 4.29 3.28 4.64†

HT Synchrous Belts

Nominal Center Distance Using DYNA-SYNC Belts

Belt Width Factor Belt Width Belt Width Code

.15 1/4 025

.28 3/8 037

.35 7/16 043

.42 1/2 050

.57 5/8 062

Teeth in Mesh factor (T.I.M.) Table Symbol None †

FEATURES/BENEFITS PAGE PT10-2

.71 3/4 075

.86 7/8 087

1.00 1 100

1.29 1-1/4 125

1.56 1-1/2 150

Shaded area indicates stock belt widths.

No. of Teeth In Mesh In Small Pulley 6 or More 5

Factor 1.00 .80

PULLEY SPECIFICATIONS PAGES PT10-3

BELT SPECIFICATIONS PAGES PT10-11

PT10-19

ENGINEERING/TECHNICAL PAGES PT10-14

Engineering

XL Belt Width Table


DYNA-SYNC

SELECTION

XL Stock Drive Selections Driven Speeds for Motor Speeds of

HT Synchrous Belts Sprockets Conveyor Components

3500 2386 2386 2334 2334 2334 2334 2334 2334 2297 2250 2227 2227 2188 2188 2188 2139 2139 2100 2100 2100 2042 2042 2042 2000 2000 2000 1969 1944 1925 1925 1909 1909 1875 1867 1838 1833 1833 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1670 1666 1641 1833 1833 1604 1604 1591 1575 1556

1750 1193 1193 1167 1167 1167 1167 1167 1167 1148 1125 1114 1114 1094 1094 1094 1059 1069 1050 1050 1050 1021 1021 1021 1000 1000 1000 984 972 963 963 955 955 937 933 919 917 917 875 875 875 875 875 875 875 875 875 875 875 835 833 820 817 817 802 802 795 788 778

1160 791 791 773 773 773 773 773 773 761 746 738 738 725 725 725 709 709 696 696 696 677 677 677 663 683 663 653 644 637 637 633 633 621 619 609 607 607 580 580 580 580 580 580 580 580 580 580 580 554 552 544 542 542 532 532 527 523 516

Speed Ratio 1.47 1.47 1.50 1.50 1.50 1.50 1.50 1.50 1.52 1.56 1.57 1.57 1.60 1.60 1.60 1.64 1.64 1.67 1.67 1.67 1.71 1.71 1.71 1.75 1.75 1.75 1.78 1.80 1.82 1.82 1.83 1.83 1.87 1.88 1.90 1.91 1.91 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.10 2.10 2.13 2.14 2.14 2.18 2.18 2.20 2.22 2.25

Pulley Combination Driver Driven No. of Pitch No. of Pitch Teeth Diam. Teeth Diam. 15XL 1.901 44XL 2.801 30XL .955 22XL 1.401 28XL 1.783 42XL 2.674 24XL 1.528 36XL 2.292 20XL 1.273 30XL 1.910 16XL 1.019 24XL 1.528 14XL .891 21XL 1.337 12XL .764 18XL 1.146 21XL 1.337 32XL 2.037 18XL 1.146 28XL 1.783 28XL 1.783 44XL 2.801 14XL .891 22XL 1.401 30XL 1.910 48XL 3.056 20XL 1.273 32XL 2.037 15XL .955 24XL 1.528 22XL 1.401 36XL 2.292 11XL .700 18XL 1.146 24XL 1.528 40XL 2.546 18XL 1.146 30XL 1.910 12XL .764 20XL 1.273 28XL 1.783 48XL 3.056 21XL 1.337 36XL 2.292 14XL .891 24XL 1.528 24XL 1.528 42XL 2.674 16XL 1.019 28XL 1.783 12XL .764 21XL 1.337 18XL 1.146 32XL 2.037 20XL 1.273 36XL 2.292 22XL 1.401 40XL 2.546 11XL .700 20XL 1.273 24XL 1.528 44XL 2.801 12XL .764 22XL 1.401 15XL .955 28XL 1.783 16XL 1.019 30XL 1.910 21XL 1.337 40XL 2.546 22XL 1.401 42XL 2.674 11XL .700 21XL 1.337 30XL 1.910 60XL 3.820 24XL 1.528 48XL 3.056 22XL 1.401 44XL 2.801 21XL 1.337 42XL 2.674 20XL 1.273 40XL 2.546 18XL 1.146 36XL 2.292 16XL 1.019 32XL 2.037 15XL .955 30XL 1.910 14XL .891 28XL 1.783 12XL .764 24XL 1.528 11XL .700 22XL 1.401 21XL 1.337 44XL 2.801 20XL 1.273 42XL 2.674 15XL .955 32XL 2.037 28XL 1.783 60XL 3.820 14XL .891 30XL 1.910 22XL 1.401 48XL 3.056 11XL .700 24XL 1.528 20XL 1.273 44XL 2.801 18XL 1.146 40XL 2.546 16XL 1.019 36XL 2.292

HP for a 1 Wide Belt for Motor Speeds of Δ 3500 2.11 1.07 1.98 1.71 1.42 1.15 1.00 .86 1.49 1.28 1.98 1.00 2.11 1.42 1.07 1.57 .79◊ 1.71 1.28 .86 1.98 1.49 1.00 1.71 1.15 .86 1.28 1.42 1.57 .79◊ 1.71 .86 1.07 1.15 1.49 1.57 .79◊ 2.11 1.71 1.57 1.49 1.42 1.28 1.15 1.07 1.00 .86 .79◊ 1.49 1.42 1.07 1.98 1.08 1.57 .79◊ 1.42 1.28 1.15

Engineering

Δ HP ratings are for conventional speed-reduction drives. For Speed-Up Drives refer to page PT10-17. ◊ Pulley Diameter is below recommended minimum. A reduction in belt life should be expected. Suggest alternate drive selection, whenever possible.

FEATURES/BENEFITS PAGE PT10-2

PULLEY SPECIFICATIONS PAGES PT10-3

1750 1.07 .53 1.00 .86 .72 .58 .50 .43 .75 .64 1.00 .50 1.07 .72 .53 .79 .39 .86 .64 .43 1.00 .75 .50 .86 .58 .43 .64 .72 .79 .39 .86 .43 .53 .58 .75 .79 .39 1.07 .86 .79 .75 .72 .64 .58 .53 .50 .43 .39 .75 .72 .53 1.00 .50 .79 .39 .72 .64 .58

1160 .71 .36 .66 .56 .46 .38 .33 .28 .50 .42 .66 .33 .71 .46 .36 .52 .26 .56 .42 .28 .66 .50 .33 .56 .38 .28 .42 .46 .52 .26 .56 .28 .36 .38 .50 .52 .26 .71 .56 .52 .50 .46 .42 .38 .36 .33 .28 .26 .50 .46 .36 .66 .33 .52 .26 .46 .42 .38

Nominal C.D. Using DYNA-SYNC Belts 60XL .... .... .... .... .... .... .... 1.48† .... .... .... .... .... .... .... .... 1.53† .... .... 1.37† .... .... .... .... .... 1.31† .... .... .... 1.42‡ .... .... .... .... .... .... 1.36‡ .... .... .... .... .... .... .... .... .... .... 1.30‡ .... .... .... .... .... .... .... .... .... ....

80XL .... 2.13 .... .... .... 1.98 2.23 2.49† .... .... .... 2.18 .... .... 2.02 .... 2.54† .... .... 2.38† .... .... 2.07 .... 1.75 2.33† .... .... .... 2.43† .... 2.27† 1.80 .... .... .... 2.37‡ .... .... .... .... .... .... .... 1.68 1.84† 2.16† 2.32‡ .... .... .... .... 1.72† .... 2.21‡ .... .... ....

90XL .... 2.64 .... .... 1.97 2.48 2.74 2.99† .... 2.17 .... 2.68 .... 1.86 2.53 .... 3.64† .... 2.06 2.88† .... .... 2.58 .... 2.26 2.83† 1.94 .... .... 2.93† .... 2.78† 2.31 2.15 .... .... 2.88† .... .... .... .... .... .... 2.03 2.19 2.35 2.67† 2.82† .... .... 2.07 .... 2.24† .... 2.71‡ .... .... ....

100XL .... 3.14 .... .... 2.48 2.98 3.24 3.49† 2.32 2.68 .... 3.19 .... 2.36 3.03 .... 3.54† .... 2.57 3.39† .... 2.09 3.08 .... 2.77 3.33† 2.46 2.13 .... 3.43† .... 3.28† 2.82 2.66 .... .... 3.38† .... .... .... .... .... 2.22 2.54 2.70 2.86 3.17† 3.33† .... .... 2.59 .... 2.75 .... 3.22† .... .... 2.31

110XL .... 3.64 .... 2.47 2.98 3.49 3.74 3.99† 2.82 3.18 .... 3.69 .... 2.87 3.53 2.56 4.04† .... 3.07 3.89† .... 2.60 3.58 .... 3.27 3.83† 2.96 2.65 2.32 3.94† .... 3.78† 3.32 3.16 2.37 .... 3.88† .... .... .... 2.25 2.41 2.74 3.05 3.21 3.37 3.68† 3.83† .... 2.29 3.10 .... 3.26 .... 3.72† .... 2.50 2.82

† ‡ See Teeth in Mesh table on opposite page. ♥ Flanges Required on both pulleys.

BELT SPECIFICATIONS PAGES PT10-11

PT10-20

70XL .... 1.63 .... .... .... .... 1.73 1.99† .... .... .... 1.68 .... .... 1.52 .... 2.03† .... .... 1.88† .... .... 1.56 .... .... 1.82† .... .... .... 1.92‡ .... 1.77† .... .... .... .... 1.87‡ .... .... .... .... .... .... .... .... .... 1.65‡ 1.81‡ .... .... .... .... .... .... 1.69} .... .... ....

ENGINEERING/TECHNICAL PAGES PT10-44


DYNA-SYNC

SELECTION

XL Stock Drive Selections 140XL 3.27 5.14 3.47 3.98 4.48 4.99 5.24 5.49† 4.33 4.68 3.36 5.19 3.04 4.38 5.04 4.07 5.54† 3.76 4.58 5.39† 3.13 4.12 5.09 3.65 4.78 5.34† 4.47 4.16 3.85 5.44† 3.54 5.29† 4.83 4.67 3.90 3.74 5.39† ...... 3.31 3.63 3.79 3.94 4.26 4.57 4.72 4.88 5.18† 5.33† 3.67 3.83 4.61 ...... 4.77 3.39 5.23† 3.72 4.03 4.35

150XL 3.77 5.64 3.97 4.48 4.99 5.49 5.74 5.99† 4.83 5.19 3.86 5.69 3.55 4.88 5.54 4.57 6.04† 4.27 5.08 5.89† 3.64 4.62 5.59 4.16 5.28 5.84† 4.98 4.67 4.36 5.94† 4.05 5.79† 5.33 5.18 4.40 4.25 5.89† ...... 3.82 4.14 4.29 4.45 4.76 5.07 5.22 5.38 5.68† 5.84† 4.18 4.34 5.12 ...... 5.27 3.91 5.73† 4.23 4.54 4.85

160XL 4.27 6.14 4.47 4.98 5.49 5.99 6.24 6.49† 5.33 5.69 4.37 6.19 4.06 5.38 6.04 5.08 6.54† 4.77 5.58 6.39† 4.15 5.12 6.09 4.66 5.78 6.34† 5.48 5.17 4.86 6.44† 4.55 6.29† 5.83 5.68 4.91 4.75 6.39† 3.36 4.33 4.64 4.80 4.95 5.26 5.57 5.73 5.88 6.18† 6.34† 4.69 4.84 5.62 3.44 5.77 4.42 6.23† 4.73 5.05 5.36

170XL 4.77 8.64 4.98 5.48 5.99 8.49 8.74 6.99† 5.84 6.19 4.87 6.69 4.56 5.88 6.54 5.58 7.04† 5.27 6.08 6.89† 4.65 5.83 6.59 5.16 6.28 6.84† 5.98 5.67 5.36 6.94† 5.06 6.79† 6.33 6.18 5.41 5.26 6.89{ 3.88 4.64 5.15 5.30 5.46 5.77 6.07 6.23 6.38 6.68† 6.84† 5.19 5.35 6.12 3.96 6.27 4.93 6.73† 5.24 5.55 5.86

180XL 5.28 7.14 5.48 5.98 8.49 6.99 7.24 7.49† 6.34 6.69 5.37 7.19 5.06 6.38 7.04 6.08 7.54† 5.77 6.58 7.39† 5.16 6.13 7.09 5.67 6.78 7.34† 6.48 6.17 5.87 7.44† 5.56 7.29† 6.83 6.68 5.91 5.76 7.39† 4.39 5.34 5.65 5.81 5.96 6.27 6.58 6.73 6.88 7.19† 7.34† 5.70 5.85 6.62 4.48 6.78 5.43 7.23† 5.74 6.05 6.36

190XL 5.78 7.64 5.98 6.48 6.99 7.49 7.74 7.99† 6.84 7.19 5.87 7.69 5.57 6.88 7.54 6.58 8.04† 6.27 7.09 7.89† 5.66 6.63 7.59 6.17 7.29 7.84† 6.98 6.68 6.37 7.94† 6.06 7.79† 7.33 7.18 6.42 6.26 7.89† 4.90 5.85 6.16 6.31 6.46 6.77 7.08 7.23 7.38 7.69† 7.84† 6.20 6.36 7.12 4.99 7.28 5.94 7.73† 6.25 6.56 6.87

200XL 6.28 8.14 6.48 6.99 7.49 7.99 8.24 8.49† 7.34 7.69 6.38 8.19 6.07 7.39 8.04 7.08 8.54† 6.78 7.59 8.39† 6.16 7.13 8.09 6.67 7.79 8.34† 7.48 7.18 6.87 8.44† 6.56 8.29† 7.83 7.68 6.92 6.77 8.39† 5.41 6.35 6.66 6.81 6.97 7.27 7.58 7.73 7.88 8.19† 8.34† 6.71 6.86 7.83 5.50 7.78 6.44 8.24† 6.75 7.06 7.37

210XL 6.78 8.64 8.98 7.49 7.99 8.49 8.74 8.99† 7.84 8.19 6.88 8.69 6.57 7.89 8.54 7.58 9.04† 7.28 8.09 8.89† 6.67 7.63 8.59 7.17 8.29 8.84† 7.98 7.68 7.37 8.94† 7.07 8.79† 8.34 8.18 7.42 7.27 8.89† 5.92 6.85 7.16 7.31 7.47 7.77 8.08 8.23 8.38 8.69† 8.84† 7.21 7.36 8.13♥ 6.01 8.28 6.95 8.74† 7.26 7.56 7.87

220XL 7.28 9.14 7.48 7.99 8.49 8.99 9.24 9.49† 8.34 8.69 7.38 9.19 7.07 8.39 9.04 8.08 9.54† 7.78 8.59 9.39† 7.17 8.13 9.09 7.67 8.79 9.34† 8.48 8.18 7.87 9.44† 7.57 9.29† 8.84 8.68 7.92 7.77 9.39† 6.42 7.36 7.66 7.82 7.97 8.28 8.58♥ 8.73 8.88 9.19† 9.34† 7.71 7.86 8.63♥ 8.52 8.78 7.45 9.24† 7.76 8.07 8.37♥

230XL 7.78 9.64 7.98 8.49 8.99 9.49 9.74 9.99† 8.84 9.19 7.88 9.69 7.57 8.89 9.54 8.58 10.04† 8.28 9.09 9.89† 7.67 8.83 9.59 8.18 9.29 9.84† 8.98 8.68 8.38 9.94† 8.07 9.79† 9.34 9.18 8.42 8.27 9.89† 6.93 7.86 8.17 8.32 8.47 8.78 9.08♥ 9.23 9.38 9.69† 9.84† 8.21 8.37 9.13♥ 7.02 9.28 7.95 9.74† 8.26 8.57 8.87♥

240XL 8.28 10.14 8.48 8.99 9.49 9.99 10.24 10.49† 9.34 9.69 8.38 10.19 8.08 9.39 10.04 9.08 10.54† 8.78 9.59 10.39† 8.17 9.13 10.09 8.68 9.79 10.34† 9.49♥ 9.18 8.88 10.44† 8.57 10.29† 9.84 9.69 8.93 8.77 10.39† 7.43 8.38 8.67 8.82 8.97 9.28♥ 9.58♥ 9.73 9.89 10.19† 10.34† 8.71 8.87 9.63♥ 7.53 9.78 8.45 10.24† 8.76 9.07 9.37♥

250XL 8.78 10.64 8.98 9.49 9.99 10.49 10.74 10.99† 9.84 10.19 8.88 10.69 8.58 9.89 10.54 9.59 11.04† 9.28 10.09 10.89† 8.67 9.63 10.59 9.18 10.29 10.84† 9.99♥ 9.68 9.38 10.94† 9.07 10.79† 10.34 10.19 9.43 9.27 10.89† 7.94 8.86 9.17 9.32 9.47 9.78♥ 10.08♥ 10.23 10.39 10.69† 10.84† 9.22 9.37 10.13♥ 8.03 10.28 8.96 10.74† 9.26 9.57♥ 9.87♥

260XL 9.28 11.14 9.49 9.99 10.49 10.99 11.24 11.49† 10.34 10.69 9.38 11.19 9.08 10.39♥ 11.04 10.09 11.54† 9.78 10.59 11.39† 9.17 10.13 11.09 9.68 10.79 11.34† 10.49♥ 10.18 9.88 11.44† 9.57 11.29† 10.84 10.69 9.93 9.77 11.39† 8.44 9.36 9.67 9.82 9.98 10.28♥ 10.58♥ 10.73 10.89 11.19† 11.34† 9.72 9.87 10.63♥ 8.53 10.78 9.46 11.24† 9.77 10.07♥ 10.38♥

Sprockets

130XL 2.76 4.64 2.96 3.47 3.98 4.49 4.74 4.99† 3.83 4.18 2.85 4.69 ...... 3.88 4.54 3.57 5.04† 3.26 4.08 4.89† ...... 3.61 4.58 3.14 4.28 4.84† 3.97 3.66 3.35 4.94† 3.03 4.78† 4.33 4.17 3.39 3.23 4.89† ...... 2.79 3.12 3.28 3.44 3.75 4.06 4.22 4.37 4.68† 4.83† 3.16 3.32 4.11 ...... 4.27 2.88 4.73† 3.20 3.53 3.84

Conveyor Components

120XL ...... 4.14 2.46 2.97 3.48 3.99 4.24 4.49† 3.33 3.68 ...... 4.19 ...... 3.37 4.04 3.06 4.54† 2.75 3.58 4.39† ...... 3.11 4.08 2.63 3.78 4.34† 3.47 3.15 2.84 4.44† 2.51 4.28† 3.82 3.67 2.88 2.72 4.38† ...... ...... 2.60 2.76 2.93 3.24 3.56 3.71 3.87 4.18† 4.33† 2.64 2.81 3.60 ...... 3.76 ...... 4.23† 2.69 3.01 3.33

HT Synchrous Belts

Nominal Center Distance Using DYNA-SYNC Belts

Belt Width Factor Belt Width Belt Width Code

.15 1/4 025

.28 3/8 037

.35 7/16 043

.42 1/2 050

.57 5/8 062

Teeth in Mesh factor (T.I.M.) Table Symbol None † ‡ FEATURES/BENEFITS PAGE PT10-2

.71 3/4 075

.86 7/8 087

1.00 1 100

1.29 1-1/4 125

1.56 1-1/2 150

Shaded area indicates stock belt widths.

No. of Teeth In Mesh In Small Pulley 6 or More 5 4

Factor 1.00 .80 .80

PULLEY SPECIFICATIONS PAGES PT10-3

BELT SPECIFICATIONS PAGES PT10-11

PT10-21

ENGINEERING/TECHNICAL PAGES PT10-14

Engineering

XL Belt Width Table


DYNA-SYNC

SELECTION

XL Stock Drive Selections Driven Speeds for Motor Speeds of

HT Synchrous Belts Sprockets Conveyor Components

3500 1531 1531 1500 1500 1458 1458 1458 1432 1400 1400 1400 1375 1361 1361 1333 1312 1312 1312 1283 1283 1273 1250 1225 1225 1203 1193 1167 1167 1167 1167 1167 1114 1094 1089 1089 1050 1050 1021 1021 1000 972 963 955 933 917 875 875 875 875 817 802 778 730 700 681 642 584 535

1750 766 766 750 750 729 729 729 716 700 700 700 688 681 681 666 656 656 656 642 642 638 625 613 613 601 597 583 583 583 583 583 557 547 535 535 525 525 510 510 500 486 481 477 467 458 438 438 438 438 408 401 389 365 350 340 321 292 267

1160 508 508 498 498 483 483 483 475 464 464 464 456 451 451 442 435 435 435 425 425 422 414 406 406 399 396 387 387 387 387 387 370 363 355 355 348 348 338 338 331 322 319 316 309 304 290 290 290 290 270 266 258 242 232 226 213 193 177

Speed Ratio 2.29 2.29 2.33 2.33 2.40 2.40 2.40 2.44 2.50 2.50 2.50 2.55 2.57 2.57 2.63 2.67 2.67 2.67 2.73 2.73 2.75 2.80 2.86 2.86 2.91 2.93 3.00 3.00 3.00 3.00 3.00 3.14 3.20 3.27 3.27 3.33 3.33 3.43 3.43 3.50 3.60 3.64 3.67 3.75 3.82 4.00 4.00 4.00 4.00 4.29 4.36 4.50 4.80 5.00 5.14 5.45 6.00 6.55

Pulley Combination Driver Driven No. of Pitch No. of Pitch Teeth Diam. Teeth Diam. 21XL 1.337 48XL 3.056 14XL .891 32XL 2.037 18XL 1.146 42XL 2.674 12XL .764 28XL 1.783 30XL 1.910 72XL 4.584 20XL 1.273 48XL 3.056 15XL .955 36XL 2.292 18XL 1.146 44XL 2.801 24XL 1.528 60XL 3.820 16XL 1.019 40XL 2.546 12XL .764 30XL 1.910 11XL .700 28XL 1.783 28XL 1.783 72XL 4.584 14XL .891 36XL 2.292 16XL 1.019 42XL 2.674 18XL 1.146 48XL 3.056 15XL .955 40XL 2.546 12XL .764 32XL 2.037 22XL 1.401 60XL 3.820 11XL .700 30XL 1.910 16XL 1.019 44XL 2.801 15XL .955 42XL 2.674 21XL 1.337 60XL 3.820 14XL .891 40XL 2.546 11XL .700 32XL 2.037 15XL .955 44XL 2.801 24XL 1.528 72XL 4.584 20XL 1.273 60XL 3.820 16XL 1.019 48XL 3.056 14XL .891 42XL 2.874 12XL .764 36XL 2.292 14XL .891 44XL 2.801 15XL .955 48XL 3.056 22XL 1.401 72XL 4.584 11XL .700 36XL 2.292 18XL 1.146 60XL 3.820 12XL .764 40XL 2.546 21XL 1.337 72XL 4.584 14XL .891 48XL 3.056 12XL .764 42XL 2.874 20XL 1.273 72XL 4.584 11XL .700 40XL 2.546 12XL .784 44XL 2.801 16XL 1.019 60XL 3.820 11XL .700 42XL 2.674 18XL 1.146 72XL 4.584 15XL .955 60XL 3.820 12XL .764 48XL 3.056 11XL .700 44XL 2.801 14XL .891 60XL 3.820 11XL .700 48XL 3.056 16XL 1.019 72XL 4.584 15XL .955 72XL 4.584 12XL .764 60XL 3.820 14XL .891 72XL 4.584 11XL .700 60XL 3.820 12XL .764 72XL 4.584 11XL .700 72XL 4.584

HP for a 1 Wide Belt for Motor Speeds of Δ 3500 1.49 1.00 1.28 .86 2.11 1.42 1.07 1.28 1.71 1.15 .86 .79◊ 1.98 1.00 1.15 1.28 1.07 .86 1.57 .79◊ 1.15 1.07 1.49 1.00 .79◊ 1.07 1.71 1.42 1.15 1.00 .86 1.00 1.07 1.57 .79◊ 1.28 .86 1.49 1.00 .86 1.42 .79◊ .86 1.15 .79 1.28 1.07 .86 .79◊ 1.00 .79◊ 1.15 1.07 .86 1.00 .79◊ .86 .79◊

Engineering

Δ HP ratings are for conventional speed-reduction drives. For Speed-Up Drives refer to page PT10-17. ◊ Pulley Diameter is below recommended minimum. A reduction in belt life should be expected. Suggest alternate drive selection, whenever possible.

FEATURES/BENEFITS PAGE PT10-2

PULLEY SPECIFICATIONS PAGES PT10-3

1750 .75 .50 .64 .43 1.07 .72 .53 .64 .86 .58 .43 .39 1.00 .50 .58 .64 .53 .43 .79 .39 .58 .53 .75 .50 .39 .53 .86 .72 .58 .50 .43 .50 .53 .79 .39 .64 .43 .75 .50 .43 .72 .39 .43 .58 .39 .64 .53 .43 .39 .50 .39 .58 .53 .43 .50 .39 .43 .39

1160 .50 .33 .42 .28 .71 .46 .36 .42 .56 .38 .28 .26 .66 .33 .38 .42 .36 .28 .52 .26 .38 .36 .50 .33 .26 .36 .56 .46 .38 .33 .28 .33 .36 .52 .26 .42 .28 .50 .33 .28 .46 .26 .28 .38 .26 .42 .36 .28 .26 .33 .26 .38 .36 .28 .33 .26 .28 .26

Nominal C.D. Using DYNA-SYNC Belts 60XL .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ....

80XL .... .... .... 1.93‡ .... .... .... .... .... .... 1.80‡ 1.97‡ .... .... .... .... .... 1.67‡ .... 1.85‡ .... .... .... .... 1.71§ .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ....

90XL .... 2.12† .... 2.44† .... .... .... .... .... .... 2.32‡ 2.49‡ 1.86† .... .... .... .... 2. 20‡ .... 2.37‡ .... .... .... .... 2.25‡ .... .... .... .... .... 1.94‡ .... .... .... 1.98§ .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ....

100XL .... 2.63† .... 2.95† .... .... 2.35† .... .... 2.05† .... 2.84† 3.00‡ 2.39† .... .... 2.09† 2.72† .... 2.88‡ .... .... .... 2.13† 2.78‡ .... .... .... .... 1.99‡ 2.48‡ .... .... .... 2.52‡ .... 2.21‡ .... .... 2.07‡ .... 2.25§ .... .... 2.11§ .... .... .... 1.96§ .... .... .... .... .... .... .... .... ....

110XL .... 3.14† 2.37† 3.46† .... .... 2.87† 2.24† .... 2.58† 3.35† 3.50† 2.91† 2.45† .... .... 2.62† 3.23† .... 3.39‡ 2.32† 2.50† .... 2.67† 3.28‡ 2.36† .... .... .... 2.54† 3.00‡ 2.40‡ .... .... 3.04‡ .... 2.75‡ .... .... 2.82‡ .... 2.79‡ 2.48‡ .... 2.66‡ .... .... 2.19§ 2.52§ .... 2.23§ .... .... .... .... .... .... ....

† ‡ § See Teeth in Mesh table on opposite page. ♥ Flanges Required on both pulleys.

BELT SPECIFICATIONS PAGES PT10-11

PT10-22

70XL .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ....

ENGINEERING/TECHNICAL PAGES PT10-44


DYNA-SYNC

SELECTION

XL Stock Drive Selections

3.27‡ .... 2.67‡ 3.15‡ .... 3.32‡ 3.02‡ .... 3.19‡ .... .... 2.75‡ 3.06‡ 2.79§ .... .... .... .... .... .... ....

140XL 3.44 4.66 3.92 4.97† .... 3.48 4.39 3.81 .... 4.12 4.86† 5.02† .... 4.44 4.01 3.57 4.17 4.75† .... 4.91† 3.89 4.05 .... 4.21 4.80† 3.94 .... .... 3.65 4.10† 4.53† 3.98‡ 3.70 .... 4.58‡ 2.77 4.30‡ .... 3.74† 4.19† .... 4.35‡ 4.07‡ 2.84‡ 4.23‡ .... 2.88‡ 3.82‡ 4.11‡ 2.92‡ 3.86‡ .... .... 3.00 .... 3.04§ .... ....

150XL 3.95 5.16 4.43 5.47† .... 4.00 4.90 4.32 3.08 4.63 5.36† 5.52† .... 4.95 4.52 4.08 4.68 5.26† 3.16 5.41† 4.41 4.56 3.20 4.72 5.30† 4.45 .... 3.24 4.17 4.61 5.04† 4.49 4.21 .... 5.08‡ 3.32 4.81† .... 4.26† 4.70† .... 4.86‡ 4.58† 3.40‡ 4.74‡ .... 3.44‡ 4.34‡ 4.63‡ 3.48‡ 4.39† .... .... 3.56‡ .... 3.60§ .... ....

160XL 4.46 5.67 4.94 5.97† .... 4.51 5.40 4.82 3.61 5.14 5.87† 6.02† .... 5.45 5.03 4.60 5.18 5.76† 3.70 5.91† 4.91 5.07 3.74 5.23 5.81†♥ 4.96 .... 3.78 4.68 5.12 5.54† 5.00 4.73 .... 5.59‡ 3.86 5.32† .... 4.77† 5.21† .... 5.37‡ 5.09† 3.94 5.25‡ .... 3.99‡ 4.86‡ 5.14‡ 4.03‡ 4.90‡ 3.06‡ 3.10‡ 4.11‡ 3.14‡ 4.15‡ 3.21§ 3.25§

170XL 4.97 6.17 5.44 6.48† .... 5.02 5.91 5.33 4.14 5.64 6.37† 6.52† .... 5.95 5.53 5.11 5.69 6.26†♥ 4.22 6.42† 5.42 5.58 4.26 5.74 6.31†♥ 5.47 3.34 4.31 5.20 5.62 6.05† 5.51 5.24 3.42 6.09†♥ 4.39 5.83† 3.46 5.28 5.72† 3.50 5.87†♥ 5.60† 4.47 5.76‡ 3.57 4.52† 5.37‡ 5.65‡♥ 4.56† 5.42‡ 3.65† 3.69‡ 4.64‡ 3.73‡ 4.68‡ 3.81§ 3.84§

180XL 5.48 6.67 5.95 8.98† 3.65 5.52 8.41 5.84 4.65 6.15 6.87† 7.02† 3.73 6.46 6.04 5.61 6.19 6.77†♥ 4.74 6.92† 5.93 8.06 4.78 6.24 6.81†♥ 5.97 3.89 4.83 5.70 6.13 6.55†♥ 6.02 5.75 3.97 6.60†♥ 4.91 6.33†♥ 4.01 5.79 6.22†♥ 4.05 6.38‡♥ 6.11‡ 5.00 6.27♥ 4.13 5.04 5.88‡ 6.16‡♥ 5.08† 5.93‡♥ 4.21† 4.25† 5.17‡ 4.29‡ 5.21‡ 4.37‡ 4.41§

190XL 5.98 7.17♥ 6.45 7.48† 4.18 6.03 6.91 6.34 5.17 6.65 7.37† 7.53† 4.26 6.96 8.54 6.12 6.70 7.27†♥ 5.26 7.42† 6.43 6.59 5.30 6.74 7.31†♥ 6.48 4.43 5.34 6.21 6.64 7.05†♥ 6.53 6.26 4.51 7.10†♥ 5.43 6.84†♥ 4.55 6.30 6.73†♥ 4.59 6.88†♥ 6.62†♥ 5.52 6.77‡♥ 4.68 5.56 6.39†♥ 6.66‡♥ 5.60† 6.44‡♥ 4.76† 4.80† 5.69‡ 4.84† 5.73‡♥ 4.92‡ 4.96§

200XL 6.49 7.67♥ 6.95 7.98† 4.70 6.53 7.42 6.85 5.68 7.15 7.87† 8.03† 4.79 7.46♥ 7.05 6.63 7.20x 7.77†♥ 5.77 7.92† 6.94 7.09 5.81 7.25♥ 7.82†♥ 6.98 4.96 5.86 6.72 7.14♥ 7.56†♥ 7.03 6.76 5.04 7.60†♥ 5.94 7.34†♥ 5.08 6.81 7.23†♥ 5.13 7.39†♥ 7.12†♥ 6.03 7.28‡♥ 5.21 6.08 6.90‡♥ 7.17‡♥ 6.12† 6.95‡♥ 5.29 5.33† 6.21‡♥ 5.38‡ 6.25‡♥ 5.46‡ 5.50‡

210XL 6.99 8.18♥ 7.46 8.48† 5.22 7.00 7.92♥ 7.35 6.19 7.66 8.38† 8.53† 5.31 7.96♥ 7.55 7.13 7.70♥ 8.27†♥ 6.28 8.42† 7.44 7.60 6.32 7.75♥ 8.32†♥ 7.49 5.48 6.37 7.22 7.64♥ 8.06†♥ 7.53♥ 7.27 5.57 8.11†♥ 6.46 7.84†♥ 5.61 7.32♥ 7.74†♥ 5.65 7.89†♥ 7.63†♥ 6.55 7.78†♥ 5.74 8.59 7.41†♥ 7.67‡♥ 6.63† 7.45‡♥ 5.82 5.86† 6.72‡♥ 5.90† 6.77‡♥ 5.99‡ 6.03‡♥

220XL 7.50 8.68♥ 7.96 8.98† 5.74 7.54 8.42♥ 7.85 6.70 8.16♥ 8.88† 9.03† 5.83 8.47♥ 8.05 7.64 8.21♥ 8.77†♥ 6.79 8.93† 7.95 8.10♥ 8.83 8.25♥ 8.82†♥ 7.99♥ 6.00 6.88 7.73 8.15♥ 8.56†♥ 8.04♥ 7.77♥ 6.09 8.61†♥ 6.97 8.35†♥ 6.13 7.82♥ 8.24†♥ 6.17 8.39†♥ 8.13†♥ 7.06 8.29†♥ 6.26 7.10 7.91†♥ 8.18‡♥ 7.15♥ 7.96‡♥ 6.34 6.39 7.23‡♥ 8.43‡ 7.28‡♥ 6.51‡♥ 6.56‡♥

230XL 8.00 9.18♥ 8.46 9.48† 6.25 8.05 8.92♥ 8.35 7.20 8.66♥ 9.38† 9.53† 6.34 8.97♥ 8.56♥ 8.14 8.71♥ 9.27†♥ 7.30 9.43† 8.45♥ 8.60♥ 7.34 8.76♥ 9.32†♥ 8.50♥ 6.52 7.39 8.23♥ 8.65♥ 9.06†♥ 8.54♥ 8.26♥ 6.60 9.11†♥ 7.48 8.85†♥ 6.65 8.33♥ 8.74†♥ 6.69 8.90†♥ 8.64†♥ 7.57 8.79†♥ 6.78 7.61 8.42†♥ 8.68†♥ 7.66♥ 8.46♥ 6.86 6.91 7.74†♥ 8.95† 7.79‡♥ 7.03‡♥ 7.08‡♥

240XL 8.50 9.68♥ 8.96 9.98† 6.76 8.55 9.42♥ 8.86 7.71 9.16♥ 9.88† 10.03† 6.85 9.47♥ 9.06♥ 8.64 9.21♥ 9.77†♥ 7.80 9.93† 8.95♥ 9.11♥ 7.85 9.26♥ 9.82†♥ 9.00♥ 7.03 7.89 8.74♥ 9.15♥ 9.57†♥ 9.05♥ 8.78♥ 7.12 9.61†♥ 7.98 9.35†♥ 7.16 8.83♥ 9.25†♥ 7.20 9.40†♥ 9.14†♥ 8.07 9.29†♥ 7.29 8.12♥ 8.92†♥ 9.19†♥ 8.16♥ 8.97‡♥ 7.38 7.42 5.25†♥ 7.47†♥ 8.30‡♥ 7.55‡♥ 7.60‡♥

250XL 9.00 10.18♥ 9.46♥ 10.48† 7.27 9.05 9.92♥ 9.36♥ 8.22 9.67♥ 10.38† 10.53† 7.36 9.97♥ 9.56♥ 9.15 9.71♥ 10.28†♥ 8.31 10.43† 9.45♥ 9.61♥ 8.35 9.78♥ 10.32†♥ 9.50♥ 7.54 8.40 9.24♥ 9.65♥ 10.07†♥ 9.55♥ 9.29♥ 7.83 10.11†♥ 8.49 9.86†♥ 7.67 9.33♥ 9.75†♥ 7.72 9.90†♥ 9.64†♥ 8.55♥ 9.80†♥ 7.81 8.63♥ 9.43†♥ 9.69†♥ 8.67♥ 9.47†♥ 7.89 7.94♥ 8.76‡♥ 7.98†♥ 8.81‡♥ 8.07‡♥ 8.11‡♥

260XL 9.51 10.68♥ 9. 97♥ 10.98† 7.78 9.55 10.42♥ 9. 86♥ 8.72 10.17♥ 10.88† 11.03† 7.87 10.47♥ 10.06♥ 9.65♥ 10.21♥ 10.78†♥ 8.81 10.93† 9.96♥ 10.11♥ 8.86 10.26♥ 10.82†♥ 10.00♥ 8.05 8.90 9.74♥ 10.16♥ 10.57†♥ 10.05♥ 9.79♥ 8.14 10.62†♥ 9.00 10.36†♥ 8.18 9.84♥ 10.25†♥ 8.23 10.40†♥ 10.14†♥ 9.09♥ 10.30†♥ 8.32 9.13♥ 9.93‡ 10.19†♥ 9.18♥ 9.98†♥ 8.41♥ 8.45♥ 9.27†♥ 8.49†♥ 9.31‡♥ 8.58‡♥ 8.63‡♥

Sprockets

130XL 2.92 4.16 3.41 4.47† .... 2.96 3.89 3.29 .... 3.61 4.36† 4.51† .... 3.93 3.50 3.04 3.66 4.25† .... 4.40† 3.38 3.54 .... 3.70† 4.29‡ 3.42 .... .... 3.13 3.58† 4.02† 3.46† 3.17‡ .... 4.07‡ .... 3.79† .... 3.21† 3.67‡ .... 3.83‡ 3.55‡ ... 3.71‡ .... .... 3.29‡ 3.59‡ .... 3.34‡ .... .... .... .... .... .... ....

Conveyor Components

120XL 2.39 3.65 2.89 3.96† .... 2.43 3.38 2.77 .... 3.10 3.85† 4.01† .... 3.42 2.98 2.51 3.14 3.74† .... 3.90‡ 2.86 3.02 .... 3.19† 3.79‡ 2.90 .... .... 2.59‡ 3.07‡ 3.51‡ 2.94† 2.63† .... 3.56‡

HT Synchrous Belts

Nominal Center Distance Using DYNA-SYNC Belts

Belt Width Factor Belt Width Belt Width Code

.15 1/4 025

.28 3/8 037

.35 7/16 043

.42 1/2 050

.57 5/8 062

.71 3/4 075

Teeth in Mesh factor (T.I.M.) Table Symbol None †

1.00 1 100

1.29 1-1/4 125

1.56 1-1/2 150

Shaded area indicates stock belt widths.

No. of Teeth In Mesh In Small Pulley 6 or More 5

FEATURES/BENEFITS PAGE PT10-2

.86 7/8 087

Factor 1.00 .80

Table Symbol ‡ §

PULLEY SPECIFICATIONS PAGES PT10-3

No. of Teeth In Mesh In Small Pulley 4 3

BELT SPECIFICATIONS PAGES PT10-11

PT10-23

Factor .60 .40

ENGINEERING/TECHNICAL PAGES PT10-14

Engineering

XL Belt Width Table


DYNA-SYNC

SELECTION

L Stock Drive Selections Driven Speeds for Motor Speeds of

HT Synchrous Belts Sprockets Conveyor Components

3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 3500 .... .... 3281 3267 3250 3231 3208 3182 3150 3111 3063 3036 3033 3000 .... 2962 2917 2917 .... 2864 2844 2800 2800 2800 2800 2750 2722 2692 2625 2625 2625 .... 2567 2545 2500 .... 2450 2450

1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1641 1633 1625 1615 1604 1591 1575 1556 1531 1531 1517 1500 1500 1481 1458 1458 1458 1432 1422 1400 1400 1400 1400 1375 1361 1346 1313 1313 1313 1313 1283 1273 1250 1250 1225 1225

1160 1160 1160 1160 1160 1160 1160 1160 1160 1160 1160 1160 1160 1160 1160 1087 1083 1077 1071 1063 1055 1044 1031 1015 1015 1005 994 994 982 967 967 967 949 943 928 928 928 928 911 902 892 870 870 870 870 851 844 829 829 812 812

Speed Ratio 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.07 1.07 1.08 1.08 1.09 1.10 1.11 1.13 1.14 1.14 1.15 1.17 1.17 1.18 1.20 1.20 1.20 1.22 1.23 1.25 1.25 1.25 1.25 1.27 1.29 1.30 1.33 1.33 1.33 1.33 1.36 1.38 1.40 1.40 1.43 1.43

Pulley Combination Driver Driven No. of Pitch No. of Pitch Teeth Diam. Teeth Diam. 48L 5.730 48L 5.730 40L 4.775 40L 4.775 32L 3.820 32L 3.820 30L 3.581 30L 3.581 28L 3.342 28L 3.342 26L 3.104 26L 3.104 24L 2.865 24L 2.865 22L 2.626 22L 2.626 20L 2.387 20L 2.387 18L 2.149 18L 2.149 16L 1.910 16L 1.910 14L 1.671 14L 1.671 12L 1.432 12L 1.432 10L 1.194 10L 1.194 30L 3.581 32L 3.820 28L 3.342 30L 3.581 26L 3.104 28L 3.342 24L 2.865 26L 3.104 22L 2.626 24L 2.865 20L 2.387 22L 2.626 18L 2.149 20L 2.387 16L 1.910 18L 2.149 28L 3.342 32L 3.820 14L 1.671 16L 1.910 26L 3.104 30L 3.581 24L 2.865 28L 3.342 12L 1.432 14L 1.671 22L 2.626 26L 3.104 40L 4.775 48L 5.730 20L 2.387 24L 2.865 10L 1.194 12L 1.432 18L 2.149 22L 2.626 26L 3.104 32L 3.820 48L 5.730 60L 7.162 32L 3.820 40L 4.775 24L 2.865 30L 3.581 16L 1.910 20L 2.387 22L 2.626 28L 3.342 14L 1.671 18L 2.149 20L 2.387 26L 3.104 30L 3.581 40L 4.775 24L 2.865 32L 3.820 18L 2.149 24L 2.865 12L 1.432 16L 1.910 22L 2.626 30L 3.581 16L 1.910 22L 2.626 20L 2.387 28L 3.342 10L 1.194 14L 1.671 28L 3.342 40L 4.775 14L 1.671 20L 2.387

HP for a 1 Wide Belt for Motor Speeds of Δ 3500 6.27 5.87 5.10 4.86 4.71 4.35 4.06 3.77 3.46 3.15 2.83 2.49◊ .... .... 4.86 4.61 4.35 4.06 3.77 3.46 3.15 2.83 4.61 2.49◊ 4.35 4.06 .... 3.77 5.87 3.46 .... 3.15 4.35 6.27 5.10 4.06 2.83 3.77 2.49◊ 3.46 4.86 4.06 3.15 .... 3.77 2.83 3.46 .... 4.61 2.49◊

Δ HP ratings are for conventional speed-reduction drives. For Speed-Up Drives refer to page PT10-17. ◊ Pulley Diameter is below recommended minimum. A reduction in belt life should be expected. Suggest alternate drive selection, whenever possible.

1750 4.06 3.47 2.83 2.66 2.49 2.32 2.15 1.98 1.80 1.62 1.45 1.27 1.09◊ .91◊ 2.66 2.49 2.32 2.15 1.98 1.80 1.62 1.45 2.49 1.27 2.32 2.15 1.09◊ 1.62 3.47 1.80 .91◊ 1.62 2.32 4.06 2.83 2.15 1.45 1.98 1.27 1.80 2.66 2.15 1.62 1.09◊ 1.98 1.45 1.80 .91◊ 2.49 1.27

1160 2.81 2.36 1.91 1.79 1.67 1.56 1.44 1.32 1.20 1.08 .97 .85 .72 .60◊ 1.79 1.67 1.56 1.44 1.32 1.20 1.08 .97 1.67 .85 1.56 1.44 .72 1.32 2.36 1.20 .60◊ 1.08 1.56 2.81 1.91 1.44 .97 1.32 .85 1.20 1.79 1.44 1.08 .72 1.32 .97 1.20 .60◊ 1.67 .85

Nominal C.D. Using DYNA-SYNC Belts 124L .... .... .... .... .... .... .... .... .... 2.82 3.20 3.57 3.95 4.32† .... .... .... .... .... .... .... .... .... 3.38 .... .... 3.76† .... .... .... 4.13‡ .... .... .... .... .... 2.81 .... 3.19 .... .... .... 3.56† .... .... 2.61 .... 3.94‡ .... 2.99

150L .... .... .... .... .... .... .... 3.38 3.76 4.13 4.51 4.89 5.26 5.64† .... .... .... .... .... 3.57 3.94 4.32 .... 4.70 .... .... 5.07† .... .... 3.37 5.45‡ 3.75 .... .... .... .... 4.13 .... 4.50 .... .... .... 3.55 4.88† .... 3.93 .... 5.26‡ .... 4.31

187L .... .... .... .... 4.13 4.51 4.88 5.26 5.63 6.01 6.39 6.76 7.14 7.51◊ .... 3.94 4.32 4.69 5.07 5.45 5.82 6.20 .... 6.57 4.12 4.50 6.95† 4.88 .... 5.25 7.32‡ 5.63 .... .... .... 4.31 6.01 .... 6.38 5.06 .... 4.10 5.44 6.76† 4.48 5.81 4.86 7.13‡ .... 6.19

210L .... .... 4.51 4.88 5.26 5.83 6.01 6.39 6.76 7.14 7.51 7.89 8.26 8.64† 4.69 5.07 5.44 5.82 6.20 6.57 6.95 7.32 4.88 7.70 5.25 5.63 8.07† 6.00 .... 6.38 8.45‡ 6.76 5.06 .... .... 5.43 7.13 5.81 7.51 6.19 .... 5.24 6.56 7.88† 5.61 6.94 5.99 8.26‡ .... 7.32

225L .... .... 5.26 5.63 6.01 6.38 6.76 7.13 7.51 7.89 8.26 8.64 9.01 9.39† 5.44 5.82 6.19 6.57 6.95 7.32 7.70 8.07 5.63 8.45 6.00 6.38 8.83† 6.76 .... 7.13 9.20‡ 7.51 5.81 .... .... 6.19 7.88 6.56 8.26 6.94 4.66 5.99 7.31 8.63† 6.37 7.69 6.74 9.01‡ 4.83 8.07

240L .... .... 6.01 6.38 6.76 7.13 7.51 7.89 8.26 8.64 9.01 9.39 9.76 10.14† 6.19 6.57 6.95 7.32 7.70 8.07 8.45 8.82 6.38 9.20 6.75 7.13 9.57◊ 7.51 .... 7.88 9.95‡ 8.26 6.56 .... 5.29 6.94 8.63 7.31 9.01 7.69 5.41 6.74 8.06 9.38† 7.12 8.44 7.49 9.76‡ 5.59 8.82

† ‡ § See Teeth in Mesh table on opposite page.

Engineering FEATURES/BENEFITS PAGE PT10-2

PULLEY SPECIFICATIONS PAGES PT10-3

BELT SPECIFICATIONS PAGES PT10-11

PT10-24

ENGINEERING/TECHNICAL PAGES PT10-44


DYNA-SYNC

SELECTION

L Stock Drive Selections 285L .... 6.76 8.26 8.63 9.01 9.39 9.76 10.14 10.51 10.89 11.26 11.64 12.01 12.39† 8.45 8.82 9.20 9.57 9.95 10.32 10.70 11.07 8.63 11.45 9.01 9.38 11.83† 9.76 5.99 10.13 12.20‡ 10.51 8.81 .... 7.49 9.19 10.88 9.57 11.26 9.94 7.67 9.00 10.32 11.64† 9.37 10.69 9.75 12.01‡ 7.85 11.07

300L .... 7.51 9.01 9.39 9.76 10.14 10.51 10.89 11.26 11.64 12.01 12.39 12.76 13.14† 9.20 9.57 9.95 10.32 10.70 11.07 11.45 11.83 9.38 12.20 9.76 10.13 12.58† 10.51 6.74 10.88 12.95‡ 11.26 9.57 .... 8.25 9.04 11.64 10.32 12.01 10.69 8.43 9.75 11.07 12.39† 10.13 11.44 10.50 12.76‡ 8.60 11.82

322L 7.13 8.63 10.14 10.51 10.89 11.26 11.64 12.01 12.39 12.76 13.14 13.51 13.89 14.26† 10.32 10.70 11.07 11.45 11.82 12.20 12.57 12.95 10.51 13.33 10.88 11.26 13.70† 11.63 7.87 12.01 14.08‡ 12.39 10.69 .... 9.37 11.07 12.76 11.44 13.14 11.82 9.55 10.88 12.19 13.51† 11.25 12.57 11.63 13.89‡ 9.73 12.95

345L 8.26 9.76 11.26 11.64 12.01 12.39 12.76 13.14 13.51 13.89 14.26 14.64 15.01 15.39† 11.47 11.82 12.20 12.57 12.95 13.33 13.70 14.07 11.63 14.45 12.01 12.38 14.83† 12.76 9.00 13.13 15.20‡ 13.51 11.82 7.45 10.50 12.19 13.89 12.57 14.26 12.94 10.68 12.00 13.32 14.64† 12.38 13.70 12.75 15.01‡ 10.86 14.11

367L 9.38 10.88 12.39 12.76 13.14 13.51 13.89 14.26 14.64 15.01 15.39 15.76 16.14 16.51† 12.57 12.95 13.32 13.70 14.07 14.45 14.82 15.20 12.76 15.58 13.14 13.51 15.95† 13.88 10.12 14.26 16.33‡ 14.64 12.94 8.58 11.62 13.32 15.01 13.69 15.39 14.11 11.81 13.13 14.45 15.76† 13.50 14.82 13.88 16.14‡ 11.99 15.20

390L 10.51 12.01 13.51 13.89 14.26 14.64 15.01 15.39 15.76 16.14 16.51 16.89 17.26 17.64† 13.70 14.07 14.45 14.82 15.20 15.58 15.95 16.33 13.88 16.70 14.26 14.64 17.08† 15.01 11.25 15.38 17.45‡ 15.76 14.11 9.36 12.75 14.44 16.13 14.82 16.51 15.20 12.93 14.25 15.57 16.89† 14.63 15.95 15.00 17.26‡ 13.12 16.32

420L 12.01 13.51 15.01 15.39 15.76 16.14 16.51 16.89 17.26 17.64 18.01 19.89 18.40 19.14† 15.20 15.57 15.95 16.33 16.70 17.07 17.45 17.83 15.38 18.20 15.76 16.13 18.57† 16.51 12.75 16.89 18.95‡ 17.26 15.57 10.86 14.25 15.94 17.64 16.32 18.01 16.70 14.44 15.75 17.07 18.39† 16.13 17.45 16.51 18.76‡ 14.62 17.82

450L 13.51 15.01 16.51 16.89 17.26 17.64 18.01 18.39 18.76 19.14 19.51 19.89 20.26 20.64† 16.70 17.07 17.45 17.82 18.20 18.57 18.95 19.32 16.89 19.70 17.26 17.64 20.08† 18.01 14.25 18.39 20.45‡ 18.76 17.07 12.36 15.75 17.45 19.14 17.82 19.51 18.20 15.94 17.26 18.57 19.89† 17.63 18.95 18.01 20.26‡ 16.12 19.32

480L 15.01 16.51 18.01 18.39 18.76 19.14 19.51 19.89 20.26 20.64 21.01 21.39 21.76 22.14† 18.20 18.57 18.95 19.32 19.70 20.08 20.45 20.82 18.39 21.20 18.76 19.13 21.58† 19.51 15.75 19.89 21.95‡ 20.26 18.57 13.87 17.26 18.95 20.64 19.32 21.01 19.70 17.44 18.76 20.07 21.39† 19.13 20.45 19.51 21.77‡ 17.62 20.82

510L 16.51 18.01 19.51 19.89 20.26 20.64 21.01 21.39 21.76 22.14 22.51 22.89 23.26 23.64† 19.70 20.07 20.45 20.82 21.20 21.58 21.95 22.33 19.89 22.70 20.26 20.64 23.08† 21.01 17.25 21.39 23.45‡ 21.76 20.07 15.37 18.76 20.45 22.14 20.82 22.51 21.20 18.94 20.26 21.57 22.89† 20.63 21.95 21.01 23.36‡ 19.12 22.32

540L 18.01 19.51 21.01 21.39 21.76 22.14 22.51 22.89 23.26 23.64 24.01 24.39 24.76 25.14† 21.20 21.57 21.95 22.33 22.70 23.08 23.45 23.83 21.39 24.20 21.76 22.14 24.58† 22.51 18.76 22.89 24.95‡ 23.36 21.57 16.87 20.26 21.95 23.64 22.32 24.01 22.70 20.44 21.76 23.07 24.39† 22.13 23.45 22.51 24.76‡ 20.63 23.82

600L 21.01 22.51 24.01 24.39 24.76 25.14 25.50 25.89 26.26 26.64 27.01 27.39 27.76 28.14† 24.20 24.57 24.95 25.33 25.70 26.08 26.45 26.83 24.39 27.20 24.76 25.14 27.58 25.51 21.76 25.89 27.95‡ 26.26 24.57 19.87 23.26 24.95 26.64 25.32 27.01 25.70 23.44 24.76 26.07 27.39† 25.13 26.45 25.51 27.76‡ 23.63 26.82

Sprockets

270L .... 6.01 7.51 7.88 5.26 8.63 9.01 9.39 9.76 10.14 10.51 10.89 11.26 11.64† 7.69 8.07 8.45 8.82 9.20 9.57 9.95 10.32 7.88 10.70 8.26 8.63 11.07† 9.01 .... 9.38 11.45‡ 9.76 8.06 .... 6.74 8.44 10.13 8.81 10.51 9.19 6.92 8.25 9.57 10.88† 8.62 9.94 9.00 11.26‡ 7.10 10.32

Conveyor Components

255L .... 5.26 6.76 7.13 7.51 7.88 8.26 8.64 9.01 9.39 9.76 10.14 10.51 10.89† 6.94 7.32 7.70 8.07 8.45 8.82 9.20 9.57 7.13 9.95 7.51 7.88 10.32† 8.26 .... 8.63 10.70‡ 9.01 7.31 .... 5.99 7.69 9.38 8.06 9.76 8.44 6.17 7.49 8.82 10.13† 7.87 9.19 8.25 10.51‡ 6.34 9.57

HT Synchrous Belts

Nominal Center Distance Using DYNA-SYNC Belts

L Belt Width Table .28 3/8 037

.35 7/16 043

.45 1/2 050

.57 5/8 062

.71 3/4 075

.86 7/8 087

1.00 1 100

Teeth in Mesh factor (T.I.M.) Table Symbol None †

1.56 1-1/2 150

1.84 1-3/4 175

2.14 2 200

2.72 2-1/2 250

3.36 3 300

Shaded area indicates stock belt widths.

No. of Teeth In Mesh In Small Pulley 6 or More 5

FEATURES/BENEFITS PAGE PT10-2

1.29 1-1/4 125

Factor 1.00 .80

Table Symbol ‡

PULLEY SPECIFICATIONS PAGES PT10-3

No. of Teeth In Mesh In Small Pulley 4

BELT SPECIFICATIONS PAGES PT10-11

PT10-25

Factor .60

ENGINEERING/TECHNICAL PAGES PT10-14

Engineering

Belt Width Factor Belt Width Belt Width Code


DYNA-SYNC

SELECTION

L Stock Drive Selections Driven Speeds for Motor Speeds of

HT Synchrous Belts Sprockets Conveyor Components

3500 2423 2406 2333 2333 2333 2333 2333 .... 2275 2250 2227 2188 2188 .... 2154 2100 2100 .... 2042 2042 2000 2000 1969 1944 .... 1925 .... 1896 1885 1867 1867 1750 1750 1750 1750 1750 .... .... 1667 1633 1633 .... 1604 .... 1575 1556 1531 1517

1750 1212 1203 1167 1167 1167 1167 1167 1167 1138 1125 1114 1094 1094 1094 1077 1050 1050 1050 1021 1021 1000 1000 985 972 972 963 955 948 942 933 933 875 875 875 875 875 875 875 833 817 817 808 802 795 788 778 766 758

1160 803 798 733 733 733 733 733 733 754 746 738 725 725 725 714 696 696 696 677 677 663 663 652 644 644 638 633 628 625 619 619 580 580 580 580 580 580 580 552 541 541 535 532 527 522 516 507 503

Speed Ratio 1.44 1.45 1.50 1.50 1.50 1.50 1.50 1.50 1.54 1.56 1.57 1.60 1.60 1.60 1.63 1.67 1.67 1.67 1.71 1.71 1.75 1.75 1.78 1.80 1.80 1.82 1.83 1.85 1.86 1.88 1.88 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.10 2.14 2.14 2.17 2.18 2.20 2.22 2.25 2.29 2.31

Pulley Combination Driver Driven No. of Pitch No. of Pitch Teeth Diam. Teeth Diam. 18L 2.149 26L 3.104 22L 2.626 32L 3.820 48L 5.730 72L 8.594 40L 4.775 60L 7.162 32L 3.820 48L 5.730 20L 2.387 30L 3.581 16L 1.910 24L 2.865 12L 1.432 18L 2.149 26L 3.104 40L 4.775 18L 2.149 28L 3.342 14L 1.671 22L 2.626 30L 3.581 48L 5.730 20L 2.387 32L 3.820 10L 1.194 16L 1.910 16L 1.910 26L 3.104 24L 2.865 40L 4.775 18L 2.149 30L 3.581 12L 1.432 20L 2.387 28L 3.342 48L 5.730 14L 1.671 24L 2.865 48L 5.730 84L 10.027 16L 1.910 28L 3.342 18L 2.149 32L 3.820 40L 4.775 72L 8.594 10L 1.194 18L 2.149 22L 2.626 40L 4.775 12L 1.432 22L 2.626 26L 3.104 48L 5.730 14L 1.671 26L 3.104 32L 3.820 60L 7.162 16L 1.910 30L 3.581 30L 3.581 60L 7.162 24L 2.865 48L 5.730 20L 2.387 40L 4.775 16L 1.910 32L 3.820 14L 1.671 28L 3.342 12L 1.432 24L 2.865 10L 1.194 20L 2.387 40L 4.775 84L 10.027 28L 3.342 60L 7.162 14L 1.671 30L 3.581 12L 1.432 26L 3.104 22L 2.626 48L 5.730 10L 1.194 22L 2.626 18L 2.149 40L 4.775 32L 3.820 72L 8.594 14L 1.671 32L 3.820 26L 3.104 60L 7.162

HP for a 1 Wide Belt for Motor Speeds of Δ 3500 3.15 3.77 6.27 5.87 5.10 3.46 2.83 .... 4.35 3.15 2.49◊ 4.86 3.46 .... 2.83 4.06 3.15 .... 4.61 2.49◊ 6.27 2.83 3.15 5.87 .... 3.77 .... 4.35 2.49◊ 5.10 2.83 4.86 4.06 3.46 2.83 2.49 .... .... 5.87 4.61 2.49◊ .... 3.77 .... 3.15 5.10 2.49◊ 4.35

Δ HP ratings are for conventional speed-reduction drives. For Speed-Up Drives refer to page PT10-17. ◊ Pulley Diameter is below recommended minimum. A reduction in belt life should be expected. Suggest alternate drive selection, whenever possible.

1750 1.62 1.98 4.06 3.47 2.83 1.80 1.45 1.09◊ 2.32 1.62 1.27 2.66 1.80 .91◊ 1.45 2.15 1.62 1.09◊ 2.49 1.27 4.06 1.45 1.62 3.47 .91◊ 1.98 1.09◊ 2.32 1.27 2.83 1.45 2.66 2.15 1.80 1.45 1.27 1.09◊ .91◊ 3.47 2.49 1.27 1.09◊ 1.98 .91◊ 1.62 2.83 1.27 2.32

1160 1.08 1.32 2.81 2.36 1.91 1.20 .97 .72 1.56 1.08 .85 1.79 1.20 .60◊ .97 1.44 1.08 .72 1.67 .85 2.81 .97 1.08 2.36 .60◊ 1.32 .72 1.56 .85 1.91 .97 1.79 1.44 1.20 .97 .85 .72 .60◊ 2.36 1.67 .85 .72 1.32 .60◊ 1.08 1.91 .85 1.56

Nominal C.D. Using DYNA-SYNC Belts 124L .... .... .... .... .... .... .... 3.36† .... .... 2.78 .... .... 3.74‡ .... .... .... 3.16† .... .... .... .... .... .... 3.54‡ .... 2.95† .... .... .... .... .... .... .... .... .... 2.72† 3.33‡ .... .... .... .... .... 3.11‡ .... .... .... ....

150L .... .... .... .... .... .... 3.73 4.68† .... .... 4.11 .... .... 5.06‡ 3.52 .... 2.92 4.48† .... 3.90 .... .... .... .... 4.86‡ .... 4.28† .... 3.69 .... .... .... .... .... .... 3.47 4.07† 4.66‡ .... .... 3.24† 3.85† .... 4.45‡ .... .... .... ....

187L 5.24 4.28 .... .... .... 4.66 5.61 6.56† .... 5.04 5.99 .... 4.45 6.94‡ 5.41 .... 4.83 6.37† .... 5.79 .... 5.21 4.62 .... 6.74‡ .... 6.17† .... 5.59 .... 5.00 .... .... .... 4.79 5.38 5.97† 6.55‡ .... .... 5.17 5.76† .... 6.35‡ .... .... 4.95† ....

210L 6.37 5.41 .... .... .... 5.79 6.74 7.69† 4.24 6.07 7.12 .... 5.59 8.07‡ 6.55 4.40 5.97 7.50† .... 6.92 .... 6.34 5.76 .... 7.87‡ 4.57 7.50† .... 6.72 .... 6.14 .... .... 4.73 5.93 6.52 7.10† 7.68‡ .... .... 6.31 6.90† .... 7.48‡ 4.89 .... 6.10 ....

225L 7.12 6.17 .... .... .... 6.54 7.50 8.44† 5.00 6.92 7.87 .... 6.34 8.82‡ 7.30 5.17 6.72 8.25† .... 7.67 .... 7.10 6.52 .... 8.62‡ 5.34 8.05† .... 7.48 .... 6.90 .... .... 5.50 6.69 7.27 7.85† 8.43‡ .... .... 7.07 7.65† .... 8.23‡ 5.67 .... 6.86 ....

240L 7.87 6.92 .... .... .... 7.30 8.25 9.19† 5.76 7.67 8.62 .... 7.10 9.57‡ 8.05 5.93 7.48 9.00† 4.73 8.43 .... 7.85 7.27 .... 9.38‡ 6.10 8.80† 4.89 8.23 .... 7.65 .... 5.05 6.27 7.45 8.03 8.61† 9.18‡ .... .... 7.83 8.41† 5.21 8.98‡ 6.44 .... 7.62 ....

† ‡ See Teeth in Mesh table on opposite page.

Engineering FEATURES/BENEFITS PAGE PT10-2

PULLEY SPECIFICATIONS PAGES PT10-3

BELT SPECIFICATIONS PAGES PT10-11

PT10-26

ENGINEERING/TECHNICAL PAGES PT10-44


DYNA-SYNC

SELECTION

L Stock Drive Selections 285L 10.13 9.18 .... .... 6.69 9.55 10.50 11.44† 8.03 9.93 10.88 6.86 9.36 11.82‡ 10.31 8.20 9.73 11.25† 7.03 10.68 .... 10.11 9.53 .... 11.63‡ 8.38 11.06† 7.20 10.49 .... 9.91 .... 7.37 8.55 9.71 10.29 10.86† 11.43‡ .... 5.68 10.09 10.67† 7.54 11.24‡ 8.72 .... 9.89 5.84

300L 10.88 9.93 .... .... 7.45 10.31 11.24 12.20† 8.78 10.68 11.63 7.62 10.11 12.57‡ 11.06 8.96 10.49 12.00† 7.79 11.43 .... 16.86 10.29 .... 12.38‡ 9.13 11.81† 7.96 11.24 6.15 10.67 6.31 8.13 9.31 10.47 11.04 11.62† 12.19‡ .... 6.47 10.85 11.42† 8.30 11.99‡ 9.48 .... 10.64 6.63

322L 12.00 11.06 .... 6.65 8.58 11.43 12.38 13.32† 9.91 11.81 12.75 8.75 11.24 13.70‡ 12.19 10.09 11.61 13.13† 8.93 12.56 .... 11.99 11.42 .... 13.51‡ 10.27 12.94† 9.10 12.37 7.32 11.80 7.48 9.27 10.44 11.60 12.17 12.74† 13.31‡ .... 7.64 11.97 12.55† 9.44 13.12‡ 10.62 .... 11.77 7.80

345L 13.13 12.18 .... 7.79 9.71 12.56 13.50 14.45† 11.04 12.94 13.88 9.89 12.37 14.82‡ 13.31 11.22 12.74 14.25† 10.06 13.69 .... 13.12 12.55 .... 14.63‡ 11.40 14.06† 10.24 13.49 8.47 12.92 8.63 10.41 11.57 12.73 13.30 13.87† 14.44‡ .... 8.80 13.10 13.67† 10.58 14.24‡ 11.75 7.10 12.90 8.97

367L 14.25 13.31 .... 8.93 10.84 13.69 14.63 15.57† 12.17 14.06 15.00 11.02 13.49 15.95‡ 14.44 12.35 13.87 15.38† 11.20 14.81 .... 14.24 13.67 7.64 15.76‡ 12.53 15.19† 11.37 14.62 9.61 14.05 9.78 11.55 12.70 13.85 14.43 15.00† 15.56‡ .... 9.95 14.23 14.80† 11.72 15.37‡ 12.88 8.29 14.03 10.12

390L 15.38 14.44 8.13 10.06 11.97 14.81 15.76 16.70† 13.30 15.19 16.13 12.15 14.62 17.07‡ 15.56 13.48 14.99 16.51† 12.33 15.94 .... 15.37 14.80 8.80 16.88‡ 13.66 16.32† 12.50 15.75 10.75 15.18 10.92 12.68 13.83 14.98 15.55 16.12† 16.69‡ .... 11.69 15.36 15.93† 12.85 16.50‡ 14.01 9.45 15.16 11.26

420L 16.88 15.94 9.65 11.57 13.48 16.31 17.26 18.20† 14.80 16.69 17.63 13.66 16.12 18.57‡ 17.06 14.98 16.50 18.01† 13.83 17.44 8.35 16.87 16.30 10.33 18.38‡ 15.16 17.82† 14.01 17.25 12.27 16.68 12.44 14.19 15.34 16.48 17.05 17.62† 18.19‡ 9.00 12.61 16.86 17.43† 14.36 18.00‡ 15.52 11.00 16.67 12.79

450L 18.38 17.44 11.17 13.08 14.98 17.81 18.76 19.70† 16.30 18.19 19.13 15.16 17.62 20.07‡ 18.56 16.48 18.00 19.51† 15.34 18.94 9.90 18.37 17.80 11.85 19.88‡ 16.66 19.32† 15.52 18.75 13.78 18.18 13.96 15.70 16.84 17.99 18.56 19.13† 19.69‡ 10.55 14.13 18.36 18.93† 15.87 19.50‡ 17.02 12.53 18.17 14.30

480L 19.88 18.94 12.68 14.59 16.48 19.32 20.26 21.20† 17.80 19.69 20.63 16.66 19.12 21.57‡ 20.07 17.99 19.50 21.01† 16.84 20.44 11.43 19.88 19.31 13.37 21.38‡ 18.17 20.82† 17.02 20.25 15.29 19.68 15.47 17.20 18.35 19.49 20.06 20.63† 21.19‡ 12.10 15.64 19.86 20.43† 17.38 21.00‡ 18.53 14.06 19.67 15.82

510L 21.38 20.44 14.19 16.09 17.99 20.82 21.76 22.70† 19.31 21.19 22.13 18.17 20.63 23.07‡ 21.57 19.49 21.00 22.51† 18.35 21.94 12.96 21.38 20.81 14.89 22.88‡ 19.67 22.32† 18.53 21.75 16.80 21.18 16.98 18.71 19.85 29.99 21.56 22.13† 22.69‡ 13.63 17.15 21.37 21.94† 18.89 22.50‡ 20.03 15.58 21.17 17.33

540L 22.88 21.94 15.69 17.60 19.49 22.32 23.26 24.20† 20.81 22.69 23.63 19.67 22.13 24.57‡ 23.07 20.99 22.50 24.01† 19.85 23.44 14.47 22.88 22.31 16.40 24.38‡ 21.17 23.82† 20.03 23.25 18.31 22.68 18.49 20.21 21.35 22.49 23.06 23.62† 24.19‡ 15.16 18.66 22.87 23.44† 20.39 24.00‡ 21.53 17.09 22.68 18.84

600L 25.88 24.94 18.70 20.60 22.49 25.32 26.26 27.20† 23.81 25.69 26.63 22.67 25.13 27.57‡ 26.07 23.99 25.50 27.01† 22.86 26.44 17.50 25.88 25.31 19.42 27.39‡ 24.18 26.82† 23.04 26.25 21.32 25.69 21.50 23.22 24.36 25.50 26.06 26.63† 27.20‡ 18.19 21.68 25.87 26.44† 23.40 27.01‡ 24.54 20.12 25.68 21.85

Sprockets

270L 9.37 8.43 .... .... 5.93 8.80 9.75 10.69† 7.27 9.18 10.13 6.10 8.60 11.07‡ 9.55 7.45 8.98 10.50† 6.27 9.93 .... 9.36 8.78 .... 10.88‡ 7.62 10.13† 6.43 9.73 .... 9.16 .... 6.60 7.79 8.96 9.54 10.11† 10.68‡ .... .... 9.34 9.91† 6.77 10.49‡ 7.96 .... 9.13 ....

Conveyor Components

255L 8.62 7.67 .... .... 5.17 8.05 9.00 9.94† 6.52 8.43 9.37 5.34 7.85 10.32‡ 8.80 6.69 8.23 9.75† 5.50 9.18 .... 8.61 8.03 .... 10.13‡ 6.86 9.56† 5.67 8.98 .... 8.41 .... 5.83 7.03 8.20 8.78 9.36† 9.93‡ .... .... 8.58 9.16† 5.99 9.74‡ 7.20 .... 8.38 ....

HT Synchrous Belts

Nominal Center Distance Using DYNA-SYNC Belts

L Belt Width Table .28 3/8 037

.35 7/16 043

.45 1/2 050

.57 5/8 062

.71 3/4 075

.86 7/8 087

1.00 1 100

Teeth in Mesh factor (T.I.M.) Table Symbol None †

1.56 1-1/2 150

1.84 1-3/4 175

2.14 2 200

2.72 2-1/2 250

3.36 3 300

Shaded area indicates stock belt widths.

No. of Teeth In Mesh In Small Pulley 6 or More 5

FEATURES/BENEFITS PAGE PT10-2

1.29 1-1/4 125

Factor 1.00 .80

Table Symbol ‡

PULLEY SPECIFICATIONS PAGES PT10-3

No. of Teeth In Mesh In Small Pulley 4

BELT SPECIFICATIONS PAGES PT10-11

PT10-27

Factor .60

ENGINEERING/TECHNICAL PAGES PT10-14

Engineering

Belt Width Factor Belt Width Belt Width Code


DYNA-SYNC

SELECTION

L Stock Drive Selections Driven Speeds for Motor Speeds of

HT Synchrous Belts Sprockets Conveyor Components

3500 .... 1458 1458 .... 1400 1400 .... 1361 .... 1333 1312 .... 1283 1264 1250 .... 1225 1167 1167 1167 1167 .... .... 1684 1069 1050 .... 1021 1000 972 933 916 875 .... .... 833 817 778 749 .... .... 681 667 583 .... .... .... .... ....

1750 750 729 729 729 700 700 700 681 673 667 656 656 642 632 625 625 613 583 583 583 583 583 547 542 535 525 525 510 500 486 467 458 438 438 438 417 408 389 375 365 350 340 333 292 292 292 250 243 208

1160 497 483 483 483 464 464 464 451 446 442 435 435 425 419 414 414 406 387 387 387 387 387 363 359 354 348 348 338 331 322 309 304 290 290 290 276 271 258 248 242 232 226 221 193 193 193 166 161 138

Speed Ratio 2.33 2.40 2.40 2.40 2.50 2.50 2.50 2.57 2.60 2.63 2.67 2.67 2.73 2.77 2.80 2.80 2.86 3.00 3.00 3.00 3.00 3.00 3.20 3.23 3.27 3.33 3.33 3.43 3.50 3.60 3.75 3.82 4.00 4.00 4.00 4.20 4.29 4.50 4.67 4.80 5.00 5.14 5.25 6.00 6.00 6.00 7.00 7.20 8.40

Pulley Combination Driver Driven No. of Pitch No. of Pitch Teeth Diam. Teeth Diam. 12L 1.432 28L 3.342 30L 3.581 72L 8.594 20L 2.387 48L 5.730 10L 1.194 24L 2.865 24L 2.865 60L 7.162 16L 1.910 40L 4.775 12L 1.432 30L 3.581 28L 3.342 72L 8.594 10L 1.194 26L 3.104 32L 3.820 84L 10.027 18L 2.149 48L 5.730 12L 1.432 32L 3.820 22L 2.626 60L 7.162 26L 3.104 72L 8.594 30L 3.581 84L 10.027 10L 1.194 28L 3.342 14L 1.671 40L 4.775 28L 3.342 84L 10.027 24L 2.865 72L 8.594 20L 2.387 60L 7.162 16L 1.910 48L 5.730 10L 1.194 30L 3.581 10L 1.194 32L 3.820 26L 3.104 84L 10.027 22L 2.626 72L 8.594 18L 2.149 60L 7.162 12L 1.432 40L 4.775 14L 1.671 48L 5.730 24L 2.865 84L 10.027 20L 2.387 72L 8.594 16L 1.910 60L 7.162 22L 2.626 84L 10.027 18L 2.149 72L 8.594 12L 1.432 48L 5.730 10L 1.194 40L 4.775 20L 2.387 84L 10.027 14L 1.671 60L 7.162 16L 1.910 72L 8.594 18L 2.149 84L 10.027 10L 1.194 48L 5.730 12L 1.432 60L 7.162 14L 1.671 72L 8.594 16L 1.671 84L 10.027 14L 1.671 84L 10.027 12L 1.432 72L 8.594 10L 1.194 60L 7.162 12L 1.432 84L 10.027 10L 1.194 72L 8.594 10L 1.194 84L 10.027

HP for a 1 Wide Belt for Motor Speeds of Δ 3500 .... 4.86 3.46 .... 4.06 2.83 .... 4.61 .... 5.10 3.15 .... 3.77 4.35 4.86 .... 2.49◊ 4.61 4.06 3.46 2.83 .... .... 4.35 3.77 3.15 .... 2.49◊ 4.06 3.46 2.83 3.77 3.15 .... .... 3.46 2.49◊ 2.83 3.15 .... .... 2.49◊ 2.83 2.49◊ .... .... .... .... ....

Engineering

Δ HP ratings are for conventional speed-reduction drives. For Speed-Up Drives refer to page PT10-17. ◊ Pulley Diameter is below recommended minimum. A reduction in belt life should be expected. Suggest alternate drive selection, whenever possible.

FEATURES/BENEFITS PAGE PT10-2

PULLEY SPECIFICATIONS PAGES PT10-3

1750 1.09◊ 2.66 1.80 .91◊ 2.15 1.45 1.09◊ 2.49 .91◊ 2.83 1.62 1.09◊ 1.98 2.32 2.66 .91◊ 1.27 2.49 2.15 1.80 1.45 .91◊ .91◊ 2.32 1.98 1.62 1.09◊ 1.27 2.15 1.80 1.45 1.98 1.62 1.09◊ .91◊ 1.80 1.27 1.45 1.62 .91◊ 1.09◊ 1.27 1.45 1.27 1.09◊ .91◊ 1.09◊ .91◊ .91◊

1160 124L 150L 187L 210L 225L 240L .72 .... 3.63 5.55 6.69 7.45† 8.20† 1.79 .... .... .... .... .... .... 1.20 .... .... .... .... 4.57 5.37 .60◊ 2.89‡ 4.24‡ 6.14‡ 7.28‡ 8.03‡ 8.78‡ 1.44 .... .... .... .... .... .... .97 .... .... .... 5.05 5.83 6.60 .72 .... 3.40‡ 5.34† 6.43† 7.24† 8.00† 1.67 .... .... .... .... .... .... .60◊ 2.64§ 4.02‡ 5.93‡ 7.07‡ 7.83‡ 8.58‡ 1.91 .... .... .... .... .... .... 1.08 .... .... .... .... 4.73 5.53 .72 .... 3.15† 5.12† 6.27† 7.03† 7.79† 1.32 .... .... .... .... .... .... 1.56 .... .... .... .... .... .... 1.79 .... .... .... .... .... .... .60◊ .... 3.79‡ 5.72‡ 6.86‡ 7.62‡ 8.38‡ .85 .... .... .... 5.21 5.99 6.77 1.67 .... .... .... .... .... .... 1.44 .... .... .... .... .... .... 1.20 .... .... .... .... .... .... .97 .... .... .... .... 4.88 5.68 .60◊ .... 3.56§ 5.50‡ 6.65‡ 7.41‡ 8.17‡ .60◊ .... 3.30§ 5.28‡ 6.44‡ 7.20‡ 7.96‡ 1.56 .... .... .... .... .... .... 1.32 .... .... .... .... .... .... 1.08 .... .... .... .... .... .... .72 .... .... 4.17‡ 5.37‡ 6.15‡ 6.93‡ .85 .... .... .... 4.19‡ 5.03† 5.84† 1.44 .... .... .... .... .... .... 1.20 .... .... .... .... .... .... .97 .... .... .... .... .... .... 1.32 .... .... .... .... .... .... 1.08 .... .... .... .... .... .... .72 .... .... .... 4.34‡ 5.18‡ 5.99‡ .60◊ .... 4.33§ 5.53§ 6.32‡ 7.09‡ 1.20 .... .... .... .... .... .... .85 .... .... .... .... .... .... .97 .... .... .... .... .... .... 1.08 .... .... .... .... .... .... .60◊ .... .... .... 4.48§ 5.33§ 6.15§ .72 .... .... .... .... .... .... .85 .... .... .... .... .... .... .97 .... .... .... .... .... .... .85 .... .... .... .... .... .... .72 .... .... .... .... .... .... .60◊ .... .... .... .... .... 4.38♣ .72 .... .... .... .... .... .... .60◊ .... .... .... .... .... .... .60◊ .... .... .... .... .... .... † ‡ § ♣ See Teeth in Mesh table on opposite page. ♥ Flanges Required on both pulleys.

BELT SPECIFICATIONS PAGES PT10-11

PT10-28

Nominal C.D. Using DYNA-SYNC Belts

ENGINEERING/TECHNICAL PAGES PT10-44


DYNA-SYNC

SELECTION

L Stock Drive Selections 285L 10.47† .... 7.70 11.04‡ 5.99 8.89 10.27† .... 10.85‡ .... 7.87 10.07† 6.15 .... .... 10.65‡ 9.06 .... .... 6.30 8.03 10.44‡ 10.24‡ .... .... 6.45 9.23† 8.19† .... .... 6.60 .... .... 8.36‡ 9.40‡ .... 6.75† .... .... 8.52‡ 6.90‡ .... .... .... .... 7.05§ .... .... ....

300L 11.22† .... 8.47 11.80‡ 6.79 9.65 11.02† ... 11.60‡ .... 8.64 10.82† 6.95 .... .... 11.40‡ 9.83 .... .... 7.10 8.80 11.20‡ 11.00‡ .... .... 7.26 10.00† 8.97† .... .... 7.41 .... 5.61† 9.13† 10.17‡ .... 7.57† 5.75‡ .... 9.29‡ 7.72‡ 5.89‡ .... .... 6.03§ 7.87§ .... 6.17♣ ....

322L 12.35† .... 9.61 12.92‡ 7.97 10.79 12.15† 6.19 12.73‡ .... 9.78 11.95† 8.13 6.34 .... 12.53‡ 10.96 .... 6.49 8.29 9.95 12.33‡ 12.13‡ .... 6.64 8.45 11.14† 10.12 .... 6.78 8.60 .... 6.93 10.28† 11.31‡ .... 8.76† 7.08† .... 10.45‡ 8.92‡ 7.22‡ .... .... 7.37 9.08§ .... 7.51§ ....

345L 13.48† 7.26 10.75 14.05‡ 9.13 11.92 13.28† 7.41 13.85‡ .... 10.92 13.08† 9.29 7.56 .... 13.66‡ 12.10 .... 7.72 9.46 11.10 13.46‡ 13.26‡ .... 7.87 9.62 12.27† 11.26 .... 8.02 9.78 .... 8.18 11.43† 12.44‡ .... 9.94† 8.33† 6.45† 11.60‡ 10.10‡ 8.48† 6.58‡ 6.72‡ 8.63‡ 10.26†♥ 6.86§ 8.78§ 7.00§

367L 14.61† 8.44 11.89 15.18‡ 10.28 13.06 14.41† 8.60 14.98‡ .... 12.06 14.21† 10.45 8.76 .... 14.79‡ 13.23 7.08 8.92 10.61 12.24 14.59‡ 14.39‡ 7.22 9.07 10.78 13.40† 12.41 7.37 9.23 10.94 7.51 9.39 12.58† 13.58‡ 7.66 11.11† 9.54 7.80† 12.75‡ 11.274 9.70† 7.94† 8.09‡ 9.85‡ 11.43†♥ 8.23§ 10.00§♥ 8.37§

390L 15.73† 9.62 13.03 16.30‡ 11.43 14.19 15.54† 9.78 16.11‡ 8.02 13.20 15.34† 11.60 9.94 8.17 15.91‡ 14.36 8.33 10.10 11.77 13.37 15.72‡ 15.52‡ 8.48 10.26 11.93 14.54† 13.55 8.63 10.42 12.10 8.78 10.58 13.72† 14.72‡ 8.93 12.26† 10.73 9.08 13.89‡ 12.43†♥ 10.89† 9.22† 9.37‡ 11.05‡ 12.59†♥ 9.52‡ 11.20§♥ 9.67§♥

.71 3/4 075

.86 7/8 087

420L 17.24† 11.16 14.54 17.81‡ 12.96 15.70 17.04† 11.33 17.61‡ 9.63 14.72 16.85† 13.18 11.49 9.78 17.42‡ 15.87 9.94 11.65 13.29 14.89 17.22‡ 17.02‡ 10.10 11.82 13.46 16.05† 15.06 10.25 11.98 13.63 10.40 12.14 15.23† 16.23‡ 10.56 13.80♥ 12.30 10.71 15.41‡ 13.97†♥ 12.46† 10.87 11.02† 12.62†♥ 14.13‡♥ 11.17‡♥ 12.78‡♥ 11.32§♥

450L 18.74† 12.70 16.05 19.31‡ 14.48 17.20 18.54† 12.86 19.11‡ 11.20 16.23 18.35† 14.65 13.03 11.36 18.92‡ 17.38 11.52 13.20 14.82 16.40 18.73‡ 18.53‡ 11.68 13.36 14.99 17.56† 16.57 11.84 13.53 15.16 12.00 13.69 16.75† 17.73‡ 12.15 15.33♥ 13.85 12.31 16.92‡ 15.49†♥ 14.02†♥ 12.47 12.62† 14.18†♥ 15.66‡♥ 12.78‡♥ 14.34‡♥ 12.93§♥

480L 20.24† 14.23 17.56 20.81‡ 15.99 18.71 20.05† 14.39 20.62‡ 12.75 17.73 19.85† 16.16 14.56 12.92 20.42‡ 18.89 13.08 14.73 16.34 17.91 20.23‡ 20.03‡ 13.24 14.90 16.51 19.06† 18.08 13.40 15.06 16.68♥ 13.56 15.23 18.25† 19.24‡ 13.72 16.85♥ 15.40♥ 13.88 18.44‡ 17.02†♥ 15.56†♥ 14.04 14.20†♥ 15.73†♥ 17.19‡♥ 14.36‡♥ 15.89‡♥ 14.52‡♥

510L 21.74† 15.75 19.06 22.31‡ 17.50 20.21 21.55† 15.92 22.12‡ 14.30 19.24 21.36† 17.68 16.09 14.46 21.92‡ 20.39 14.63 16.26 17.85 19.42 21.73‡ 21.54‡ 14.79 16.43 18.02♥ 20.57† 19.59 14.95 16.59 18.20♥ 15.12 16.76 19.77† 20.75‡ 15.28 18.37♥ 16.93♥ 15.44 19.95‡ 18.54†♥ 17.10♥ 15.60♥ 15.76†♥ 17.26†♥ 18.71‡♥ 15.93‡♥ 17.43‡♥ 16.09‡♥

540L 23.24† 17.27 20.57 23.81‡ 19.01 21.72 23.05† 17.44 23.62‡ 15.83 20.75 22.86† 19.19 17.61 16.00 23.43‡ 21.89 16.16 17.78 19.36♥ 20.93 23.23‡ 23.04‡ 16.33 17.95 19.54♥ 22.08† 21.10 16.49 18.12 19.71♥ 16.66 18.29♥ 21.28† 22.25‡ 16.82 19.83♥ 18.46♥ 16.99 21.46‡ 20.06†♥ 18.63♥ 17.15♥ 17.32†♥ 18.79†♥ 20.23‡♥ 17.48†♥ 18.96‡♥ 17.64‡♥

600L 26.25† 20.29 23.58 26.81‡ 22.03 24.72 26.05† 20.47 26.62‡ 18.88 23.76 25.86† 22.21♥ 20.64 19.05 26.43‡ 24.90 19.22 20.81 22.38♥ 23.94 26.24‡ 26.04‡ 19.39 20.99 22.56♥ 25.08† 24.11 19.56 21.16 22.73♥ 19.18 21.33♥ 24.29† 25.26‡ 19.89♥ 22.91♥ 21.50♥ 20.06♥ 24.47‡ 23.08†♥ 21.67♥ 20.23♥ 20.39♥ 21.84†♥ 23.26‡♥ 20.56†♥ 22.01‡♥ 20.73‡♥

Sprockets

270L 9.71† .... 6.93 10.29‡ .... 8.13 9.51† .... 10.09‡ .... 7.09 9.31† 5.33 .... .... 9.89‡ 8.30 .... .... 5.48 7.26 9.69‡ 9.48‡ .... .... 5.62 8.47† 7.42† .... .... 5.77 .... .... 7.58‡ 8.64‡ .... 5.92‡ .... .... 7.74‡ 6.07‡ .... .... .... .... 6.21§ .... .... ....

Conveyor Components

255L 8.96† .... 6.15 9.54‡ .... 7.37 8.76† .... 9.34‡ .... 6.31 8.55† .... .... .... 9.14‡ 7.54 .... .... .... 6.47 8.93‡ 8.72‡ .... .... .... 7.70† 6.63† .... .... 4.91 .... .... 6.79‡ 7.87‡ .... 5.05‡ .... .... 6.95 5.19§ .... .... .... .... 5.33§ .... .... ....

HT Synchrous Belts

Nominal Center Distance Using DYNA-SYNC Belts

L Belt Width Table .28 3/8 037

.35 7/16 043

.45 1/2 050

.57 5/8 062

1.00 1 100

Teeth in Mesh factor (T.I.M.) Table Symbol None † ‡

1.56 1-1/2 150

1.84 1-3/4 175

2.14 2 200

2.72 2-1/2 250

3.36 3 300

Shaded area indicates stock belt widths.

No. of Teeth In Mesh In Small Pulley 6 or More 5 4

FEATURES/BENEFITS PAGE PT10-2

1.29 1-1/4 125

Factor 1.00 .80 .60

Table Symbol § ♣

PULLEY SPECIFICATIONS PAGES PT10-3

No. of Teeth In Mesh In Small Pulley 3 2

BELT SPECIFICATIONS PAGES PT10-11

PT10-29

Factor .40 .20

ENGINEERING/TECHNICAL PAGES PT10-14

Engineering

Belt Width Factor Belt Width Belt Width Code


DYNA-SYNC

SELECTION

H Stock Drive Selections Driven Speeds for Motor Speeds of

HT Synchrous Belts Sprockets Conveyor Components

3500 .... 3500 3500 3500 3500 3500 3500 3500 3500 3500 .... .... 3281 3267 3250 3231 3208 3182 3150 .... 3063 .... 3033 3000 2962 2917 2917 2864 2844 .... 2800 2800 .... 2750 .... 2692 2625 2625 2625 2567 .... 2500 2450 .... 2423 2406

1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 1750 .... 1641 1633 1625 1615 1604 1591 1575 1556 1531 .... 1517 1500 1481 1458 1458 1432 1422 1400 1400 1400 1400 1375 .... 1346 1313 1313 1313 1283 1273 1250 1225 .... 1212 1203

1160 1160 1160 1160 1160 1160 1160 1160 1160 1160 1160 1160 1160 1087 1083 1077 1071 1063 1055 1044 1031 1015 1015 1005 994 982 967 967 949 943 928 928 928 928 911 902 892 870 870 870 851 844 829 812 812 803 798

Speed Ratio 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.07 1.07 1.08 1.08 1.09 1.10 1.11 1.13 1.14 1.14 1.15 1.17 1.18 1.20 1.20 1.22 1.23 1.25 1.25 1.25 1.25 1.27 1.29 1.30 1.33 1.33 1.33 1.36 1.38 1.40 1.43 1.43 1.44 1.45

Pulley Combination Driver Driven No. of Pitch No. of Pitch Teeth Diam. Teeth Diam. 48H 7.839 48H 7.639 40H 6.366 40H 6.366 32H 5.093 32H 5.093 30H 4.775 30H 4.775 28H 4.456 28H 4.456 26H 4.138 26H 4.138 24H 3.820 24H 3.820 22H 3.501 22H 3.501 20H 3.183 20H 3.183 18H 2.865 18H 2.865 16H 2.546 16H 2.546 14H 2.228 14H 2.228 30H 4.775 32H 5.093 28H 4.456 30H 4.775 26H 4.138 28H 4.456 24H 3.820 26H 4.138 22H 3.501 24H 3.820 20H 3.183 22H 3.501 18H 2.865 20H 3.183 16H 2.546 18H 2.865 28H 4.456 32H 5.093 14H 2.228 16H 2.546 26H 4.138 30H 4.775 24H 3.820 28H 4.456 22H 3.501 26H 4.138 40H 6.366 48H 7.639 20H 3.183 24H 3.820 18H 2.865 22H 3.501 26H 4.138 32H 5.093 48H 7.639 60H 9.549 32H 5.093 40H 6.366 24H 3.820 30H 4.775 16H 2.546 20H 3.183 22H 3.501 28H 4.456 14H 2.228 18H 2.865 20H 3.183 26H 4.138 30H 4.775 40H 6.366 24H 3.820 32H 5.093 18H 2.865 24H 3.820 22H 3.501 30H 4.775 16H 2.546 22H 3.501 20H 3.183 28H 4.456 28H 4.456 40H 6.366 14H 2.228 20H 3.183 18H 2.865 26H 4.138 22H 3.501 32H 5.093

HP for a 1 Wide Belt for Motor Speeds of Δ 3500 .... 20.08 17.40 16.59 15.74 14.80 13.82 12.84 11.77◊ 10.71◊ .... .... 16.59 15.74 14.80 13.82 12.84 11.77◊ 10.71◊ .... 15.74 .... 14.80 13.82 12.84 20.08 11.77◊ 10.71◊ 14.80 .... 17.40 13.82 .... 12.84 .... 11.77◊ 16.59 13.82 10.71◊ 12.84 .... 11.77◊ 15.74 10.71◊ 12.84

1750 13.84 11.79 9.60 9.03 8.46 7.88 7.30 6.71 6.11 5.52◊ 4.91◊ .... 9.03 8.46 7.88 7.30 6.71 6.11 5.52◊ 4.91◊ 8.46 .... 7.88 7.30 6.71 11.79 6.11 5.52◊ 7.88 13.84 9.60 7.30 4.91◊ 6.71 .... 6.11 9.03 7.30 5.52◊ 6.71 4.91◊ 6.11 8.46 .... 5.52◊ 6.71

Δ HP ratings are for conventional speed-reduction drives. For Speed-Up Drives refer to page PT10-17. ◊ Pulley Diameter is below recommended minimum. A reduction in belt life should be expected. Suggest alternate drive selection, whenever possible.

1160 240H 270H 9.55 .... .... 8.03 .... .... 6.48 .... 5.51 6.08 .... 6.01 5.68 5.01 6.51 5.28 5.51 7.01 4.89 6.01 7.51 4.48 6.51 8.01 4.08 7.01 8.51 3.68 7.51 9.01 3.27◊ 8.01 9.51 2.86◊ 8.51 10.01 6.08 .... 5.75 5.68 .... 6.25 5.28 5.25 6.75 4.89 5.76 7.26 4.48 6.26 7.76 4.08 6.76 8.26 3.68 7.26 8.76 3.27◊ 7.76 9.26 5.68 .... 6.00 2.86◊ 8.26 9.76 5.28 5.00 6.50 4.89 5.50 7.00 4.48 6.00 7.50 8.03 .... .... 4.08 6.50 8.00 3.68 7.01 8.50 5.28 .... 6.24 9.55 .... .... 6.48 .... .... 4.89 5.24 6.40 3.27◊ 7.50 9.00 4.48 5.74 7.24 2.86◊ 8.00 9.50 4.08 6.24 7.74 6.08 .... .... 4.89 4.97 6.48 3.68 6.74 8.24 4.48 5.47 6.98 3.27◊ 7.24 8.75 4.08 5.97 7.48 5.68 .... .... 2.86◊ 7.75 9.25 3.68 6.48 7.98 4.48 5.20 6.71 ♥ Flanges Required on

Nominal C.D. Using DYNA-SYNC Belts 300H .... .... 7.01 7.51 8.01 8.51 9.01 9.51 10.01 10.51 11.01 11.51 7.25 7.26 8.26 8.76 9.26 9.76 10.26 10.76 7.50 11.26 8.00 8.50 9.00 .... 9.50 10.00 7.74 .... .... 8.24 10.50 8.74 11.01 9.25 6.20 7.98 9.75 8.48 10.25 8.99 6.50 10.75 9.49 8.22

330H .... .... 8.51 9.01 9.51 10.01 10.51 11.01 11.51 12.01 12.51 13.01 8.76 9.26 9.76 10.26 10.76 11.26 11.76 12.26 9.00 12.76 9.50 10.00 10.50 .... 11.00 11.51 9.24 .... 7.43 9.75 12.01 10.25 12.51 10.75 7.72 9.49 11.25 9.99 11.75 10.49 7.95 12.25 10.99 9.73

360H .... 8.01 10.01 10.51 11.01 11.51 12.01 12.51 13.01 13.51 14.01 14.51 10.26 10.76 11.26 11.76 12.26 12.76 13.26 13.76 10.50 14.26 11.00 11.50 12.01 .... 12.51 13.01 10.75 .... 8.98 11.25 13.51 11.75 14.01 12.25 9.22 10.99 12.75 11.49 13.25 11.99 9.46 13.75 12.49 11.23

390H .... 9.51 11.51 12.01 12.51 13.01 13.51 14.01 14.51 15.01 15.51 16.01 11.76 12.26 12.76 13.26 13.76 14.26 14.76 15.26 12.01 15.76 12.51 13.01 13.50 8.48 14.01 14.51 12.25 .... 10.49 12.75 15.01 13.25 15.51 13.75 10.73 12.49 14.25 12.99 14.75 13.49 10.97 15.25 14.00 12.73

420H 9.01 11.01 13.01 13.51 14.01 14.51 15.01 15.51 16.01 16.51 17.01 17.51 13.26 13.76 14.26 14.76 15.26 15.75 16.26 16.76 13.51 17.26 14.01 14.51 15.01 9.99 15.51 16.01 13.75 .... 11.99 14.25 16.51 14.75 17.02 15.26 12.24 14.00 15.76 14.50 16.25 15.00 12.47 16.75 15.50 14.24

both pulleys.

Engineering FEATURES/BENEFITS PAGE PT10-2

PULLEY SPECIFICATIONS PAGES PT10-3

BELT SPECIFICATIONS PAGES PT10-11

PT10-30

ENGINEERING/TECHNICAL PAGES PT10-44


DYNA-SYNC

SELECTION

H Stock Drive Selections 510H 13.51 15.51 17.51 18.01 18.51 19.01 19.51 20.01 20.51 21.01 21.51 22.01 17.76 18.26 18.76 19.26 19.76 20.36 20.76 21.26 18.01 21.76 18.51 19.01 19.51 14.49 20.01 20.51 18.25 11.97 16.50 18.80 21.01 19.25 21.51 19.76 16.74 18.50 20.26 19.00 20.76 19.50 16.98 21.26 20.00 18.74

540H 15.01 17.01 19.01 19.51 20.01 20.51 21.01 21.51 22.01 22.51 23.01 23.51 19.26 19.76 20.26 20.76 21.26 21.76 22.26 22.76 19.51 23.36 20.01 20.51 21.01 16.00 21.51 22.01 19.76 13.47 18.00 20.25 22.51 20.76 23.01 21.26 18.24 20.00 21.76 20.50 22.26 21.00 18.48 22.76 21.50 20.24

570H 16.51 18.51 20.51 21.01 21.51 22.01 22.51 23.01 23.51 24.01 24.51 25.01 20.76 21.26 21.76 22.26 22.76 23.26 23.76 24.26 21.01 24.76 21.51 22.01 22.51 17.50 23.01 23.51 21.25 14.98 19.50 21.76 24.01 22.26 24.51 22.76 19.74 21.50 23.26 22.00 23.76 22.50 19.99 24.26 23.00 21.75

600H 18.01 20.01 22.01 22.51 23.01 23.51 24.01 24.51 25.01 25.51 26.01 26.51 22.26 22.76 23.26 23.76 24.26 24.76 25.26 25.76 22.51 26.26 23.01 23.51 24.01 19.00 24.51 25.01 22.76 16.48 21.00 23.26 25.51 23.76 26.01 24.26 21.25 23.00 24.76 23.50 25.26 24.00 21.49 25.76 24.50 23.18

630H 19.51 21.51 23.51 24.01 24.51 25.01 25.51 26.01 26.51 27.01 27.51 28.01 23.76 24.26 24.76 25.26 25.76 26.26 26.76 27.26 24.01 27.76 24.51 25.01 25.51 20.50 26.01 26.51 24.26 17.98 22.50 24.76 27.01 25.26 27.51 25.76 22.75 24.50 26.25 25.00 26.76 25.50 22.99 27.26 26.01 24.75

660H 21.01 23.01 25.01 25.51 26.01 26.51 27.01 27.51 28.01 28.51 29.01 29.51 25.26 25.76 26.26 26.76 27.26 27.76 28.26 28.76 25.51 29.26 26.01 26.51 27.01 22.00 27.51 28.01 25.76 19.48 24.00 26.25 28.51 26.76 29.01 27.26 24.25 26.00 27.76 26.50 28.26 27.00 24.49 28.75 27.50 26.25

700H 23.01 25.01 27.01 27.51 28.01 28.51 29.01 29.51 30.01 30.51 31.01 31.51 27.26 27.76 28.26 28.76 29.26 29.76 30.26 30.76 27.51 31.26 28.01 28.51 29.01 24.00 29.51 30.01 27.76 21.49 26.00 28.26 30.51 28.76 31.01 29.26 26.25 28.00 29.76 28.50 30.26 29.01 26.49 30.76 29.51 28.25

1.29 1-1/4 125

1.56 1-1/2 150

750H 25.51 27.51 29.51 30.01 30.51 31.01 31.51 32.01 32.51 33.01 33.51 34.01 29.76 30.26 30.76 31.26 31.76 32.26 32.76 33.26 30.01 33.76 30.51 31.01 31.51 26.51 32.01 32.51 30.25 23.99 28.50 30.76 33.01 31.26 33.51 31.29 28.75 30.50 32.25 31.00 32.76 31.50 29.00 33.26 32.01 30.75

800H 28.01 30.01 32.01 32.51 33.01 33.51 34.01 34.51 35.01 35.51 36.01 36.51 32.26 32.76 33.26 33.76 34.26 34.76 35.26 35.76 32.51 36.26 33.01 33.51 34.01 29.00 34.51 35.01 32.76 26.49 31.00 33.26 35.51 33.76 36.01 34.26 31.25 33.00 34.76 33.51 35.26 34.01 31.50 35.76 34.51 33.25

850H 30.51 32.51 34.51 35.01 35.51 36.01 36.51 37.01 37.51 38.01 38.51 39.01 34.76 35.26 35.76 36.26 36.76 37.26 37.76 38.26 35.01 38.76 35.51 36.01 36.51 31.50 37.01 37.50 36.26 28.99 33.50 35.75 38.01 36.26 38.51 36.76 33.75 35.51 37.26 36.01 37.76 36.50 34.00 38.26 37.01 35.75

900H 33.01 35.01 37.01 37.51 38.01 38.51 39.01 39.51 40.01 40.51 41.01 41.51 37.26 37.76 38.26 38.76 39.26 39.76 40.26 40.76 37.51 41.26 38.01 38.51 39.01 34.00 39.51 40.01 37.76 31.50 36.01 38.26 40.51 38.76 41.01 39.25 36.25 38.01 39.76 38.50 40.26 39.01 36.50 40.77 39.51 38.25

1000H 38.01 40.01 42.01 42.51 43.01 43.51 44.01 44.51 45.01 45.51 46.01 46.51 42.26 42.76 43.26 43.76 44.26 44.76 45.26 45.76 42.51 46.26 43.01 43.51 44.01 39.01 44.51 45.01 42.76 36.50 41.00 43.26 45.51 43.76 46.01 44.26 41.25 43.00 44.76 43.51 45.26 44.00 41.50 45.76 44.51 43.25

1100H 43.01 45.01 47.01 47.51 48.01 48.51 49.01 49.51 50.01 50.51 51.01 51.51 47.26 47.76 48.26 48.76 49.26 49.76 50.26 50.76 47.51 51.26 48.01 48.51 49.01 44.00 49.51 50.01 47.76 41.50 46.01 48.26 50.51 48.76 51.01 49.26 46.25 48.01 49.76 48.51 50.26 49.01 46.50 50.76 49.51 48.25

1250H 50.51 52.51 54.51 55.01 55.51 56.01 56.51 57.01 57.51 58.01 58.51 59.01 54.16 55.26 55.76 56.26 56.76 57.26 57.76 58.26 55.01 58.76 55.51 56.01 56.51 51.51 57.01 57.51 55.26 49.00 53.51 55.76 58.01 56.26 58.51 56.76 53.75 55.51 57.26 56.01 57.76 56.51 54.00 58.26 57.01 55.76

1400H 1700H 58.01 73.01 60.01 15.01 62.01 77.01 62.51 77.51 63.01 78.01 63.51 78.51 64.01 79.01 64.51 79.51 65.01 80.01 65.51 80.51 66.01 81.01 66.51 81.51 62.26 77.26 62.76 77.76 63.26 78.26 63.76 78.76 64.26 79.26 64.76 79.76 62.26 80.26 65.76 80.76 62.51 77.51 66.26 81.26 63.01 78.01 63.51 78.51 64.01 79.01 59.01 74.01 64.51 79.51 65.01 80.01 62.76 77.76 56.50 71.50♥ 61.01 76.01 63.26 78.26 65.51 80.51 63.76 78.76 66.01 81.01 64.26 79.26 61.26 76.26 63.01 78.01 64.76 79.76 63.51 78.52 65.26 80.26 64.01 79.01 61.50 76.50 65.76 80.76 64.51 79.51 63.25 78.26

H Belt Width Table Belt Width Factor Belt Width Belt Width Code

.42 1/2 050

.57 5/8 062

.71 3/4 075

.86 7/8 087

1.00 1 100

1.84 1-3/4 175

2.14 2 200

2.72 2-1/2 250

3.36 3 300

4.06 3-1/2 350

4.76 4 400

6.15 5 500

7.50 6 600

8.89 7 700

Sprockets

480H 12.01 14.01 16.01 16.51 17.01 17.51 18.01 18.51 19.01 19.51 20.01 20.51 16.26 16.76 17.26 17.76 18.26 18.75 19.26 19.76 16.51 20.26 17.01 17.51 18.01 12.99 18.51 19.01 16.75 10.46 15.00 17.25 19.51 17.75 20.01 18.25 15.24 17.00 18.80 17.50 19.26 18.00 15.48 19.76 18.50 17.24

Conveyor Components

450H 10.51 12.51 14.51 15.01 15.51 16.01 16.51 17.01 17.51 18.01 18.51 19.01 14.76 15.26 15.76 16.26 16.76 17.26 17.76 18.26 15.01 18.76 15.51 16.01 16.51 11.49 17.01 17.51 15.24 8.95 13.49 15.75 18.01 16.25 18.51 16.75 13.74 15.50 17.25 16.00 17.76 16.50 13.98 18.26 17.00 15.74

HT Synchrous Belts

Nominal Center Distance Using DYNA-SYNC Belts

10.32 8 800

Engineering

Shaded area indicates stock belt widths.

FEATURES/BENEFITS PAGE PT10-2

PULLEY SPECIFICATIONS PAGES PT10-3

BELT SPECIFICATIONS PAGES PT10-11

PT10-31

ENGINEERING/TECHNICAL PAGES PT10-14


DYNA-SYNC

SELECTION

H Stock Drive Selections Driven Speeds for Motor Speeds of

HT Synchrous Belts Sprockets Conveyor Components

3500 .... 2333 2333 2333 .... 2275 2250 .... 2188 2188 .... 2100 2100 2042 .... .... .... 1969 1944 1925 1896 .... 1867 .... .... 1750 1750 1750 .... .... 1667 1633 .... 1604 1575 1556 .... 1517 1458 1458 1458 .... 1400 .... 1361 1333

1750 1167 1167 1167 1167 1167 1138 1125 .... 1094 1094 1077 1050 1050 1021 .... 1000 1000 985 972 963 948 .... 933 933 875 875 875 875 875 .... 833 817 .... 802 788 778 .... 758 729 729 729 700 700 700 681 667

1160 773 773 773 773 773 754 746 738 725 725 714 696 696 677 677 663 663 652 644 638 628 625 619 619 580 580 580 580 580 580 552 541 541 532 522 516 507 503 483 483 483 464 464 464 451 442

Speed Ratio 1.50 1.50 1.50 1.50 1.50 1.54 1.56 1.57 1.60 1.60 1.63 1.67 1.67 1.71 1.71 1.75 1.75 1.78 1.80 1.82 1.85 1.86 1.88 1.88 2.00 2.00 2.00 2.00 2.00 2.00 2.10 2.14 2.14 2.18 2.22 2.25 2.29 2.31 2.40 2.40 2.40 2.50 2.50 2.50 2.57 2.63

Pulley Combination Driver Driven No. of Pitch No. of Pitch Teeth Diam. Teeth Diam. 48H 7.639 72H 11.459 40H 6.366 60H 9.549 32H 5.093 48H 7.639 20H 3.183 30H 4.775 16H 2.546 24H 3.820 26H 4.138 40H 6.366 18H 2.865 28H 4.456 14H 2.228 22H 3.501 30H 4.775 48H 7.639 20H 3.183 32H 5.093 16H 2.546 26H 4.138 24H 3.820 40H 6.366 18H 2.865 30H 4.775 28H 4.456 48H 7.639 14H 2.228 24H 3.820 48H 7.639 84H 13.369 16H 2.546 28H 4.456 18H 2.865 32H 5.093 40H 6.366 72H 11.459 22H 3.501 40H 6.366 26H 4.138 48H 7.639 14H 2.226 26H 4.138 32H 5.093 60H 9.549 16H 2.546 30H 4.775 48H 7.639 96H 15.279 30H 4.775 60H 9.549 24H 3.820 48H 7.639 20H 3.183 40H 6.366 16H 2.546 32H 5.093 14H 2.228 28H 4.456 40H 6.366 84H 13.369 28H 4.456 60H 9.549 14H 2.228 30H 4.775 22H 3.501 48H 7.639 18H 2.865 40H 6.366 32H 5.093 72H 11.459 14H 2.228 32H 5.093 26H 4.138 60H 9.549 40H 6.366 96H 15.279 30H 4.775 72H 11.459 20H 3.183 48H 7.639 48H 7.639 120H 19.099 24H 3.820 60H 9.549 16H 2.546 40H 6.366 28H 4.456 72H 11.459 32H 5.093 84H 13.369

HP for a 1 Wide Belt for Motor Speeds of Δ 3500 .... 20.08 17.40 11.77◊ .... 14.80 10.71◊ .... 16.59 11.77◊ .... 13.82 10.71◊ 15.74 .... .... .... 10.71◊ 20.08 12.84 14.80 .... 17.40 .... .... 16.59 13.82 11.77◊ .... .... 20.08 15.74 .... 12.84 10.71◊ 17.40 .... 14.80 20.08 16.59 11.77◊ .... 13.82 .... 15.74 17.40

1750 13.84 11.79 9.60 6.11 4.91◊ 7.88 5.52◊ .... 9.03 6.11 4.91◊ 7.30 5.52◊ 8.46 .... 13.84 4.91◊ 5.52◊ 11.79 6.71 7.88 .... 9.60 4.91◊ 13.84 9.03 7.30 6.11 4.91◊ .... 11.79 8.46 .... 6.71 5.52◊ 9.60 .... 7.88 11.79 9.03 6.11 13.84 7.30 4.91◊ 8.46 9.60

Δ HP ratings are for conventional speed-reduction drives. For Speed-Up Drives refer to page PT10-17. ◊ Pulley Diameter is below recommended minimum. A reduction in belt life should be expected. Suggest alternate drive selection, whenever possible.

1160 240H 270H 9.55 .... .... 8.03 .... .... 6.48 .... .... 4.08 5.70 7.21 3.27◊ 6.98 8.48 5.28 .... .... 3.68 6.21 7.72 2.86◊ 7.48 8.99 6.08 .... .... 4.08 5.42 6.94 3.27◊ 6.71 8.22 4.89 .... .... 3.68 5.93 7.45 5.68 .... .... 2.86◊ 7.22 8.72 9.55 .... .... 3.27◊ 6.44 7.95 3.68 5.65 7.17 8.03 .... .... 4.48 .... 5.57 5.28 .... .... 2.86◊ 6.94 8.45 6.48 .... .... 3.27◊ 6.16 7.68 9.55 .... .... 6.08 .... .... 4.89 .... .... 4.08 .... 5.78 3.27◊ 5.87 7.40 2.66◊ 6.67 8.18 8.03 .... .... 5.68 .... .... 2.86◊ 6.38 7.90 4.48 .... .... 3.68 .... 6.00 6.48 .... .... 2.86◊ 6.09 7.62 5.28 .... .... 8.03 .... .... 6.08 .... .... 4.08 .... .... 9.55 .... .... 4.89 .... .... 3.27◊ .... 6.21 5.68 .... .... 6.48 .... .... ♥ Flanges Required on

Nominal C.D. Using DYNA-SYNC Belts 300H .... .... .... 8.72 9.99 6.66 9.22 10.49 .... 8.45 9.73 6.89 8.96 .... 10.23 .... 9.46 8.69 .... 7.11 .... 9.96 .... 9.19 .... .... .... 7.33 8.92 9.69 .... .... 9.42 .... 7.55 .... 9.15 .... .... .... 6.09 .... .... 7.77 .... ....

330H .... .... .... 10.23 11.49 8.18 10.73 11.99 6.60 9.96 11.23 8.41 10.46 6.82 11.74 .... 10.97 10.20 .... 8.64 7.04 11.47 .... 10.70 .... .... 7.25 8.86 10.43 11.20 .... .... 10.94 7.47 9.09 .... 10.66 .... .... .... 7.68 .... .... 9.31 .... ....

360H .... .... 7.90 11.73 12.99 9.69 12.23 13.50 8.13 11.47 12.73 9.93 11.97 8.35 13.24 .... 12.47 11.71 .... 10.16 8.58 12.97 .... 12.21 .... .... 8.80 10.39 11.94 12.71 .... .... 12.44 9.02 10.61 .... 12.18 .... .... .... 9.24 .... .... 10.84 .... ....

390H .... .... 9.42 13.24 14.50 11.20 13.74 15.00 9.65 12.97 14.24 11.44 13.48 9.88 14.74 .... 13.98 13.21 .... 11.67 10.11 14.48 7.68 13.71 .... 7.89 10.33 11.90 13.45 14.22 .... 8.10 13.95 10.55 12.13 .... 13.68 8.31 .... .... 10.78 .... 8.52 12.36 .... ....

420H .... 8.35 10.93 14.74 16.00 12.71 15.24 16.50 11.17 14.48 15.74 12.95 14.98 11.40 16.24 .... 15.48 14.72 .... 13.18 11.63 15.98 9.24 15.22 .... 9.45 11.85 13.41 14.96 15.72 .... 9.67 15.46 12.08 13.65 .... 15.19 9.88 .... .... 12.31 .... 10.10 13.88 .... ....

both pulleys.

Engineering FEATURES/BENEFITS PAGE PT10-2

PULLEY SPECIFICATIONS PAGES PT10-3

BELT SPECIFICATIONS PAGES PT10-11

PT10-32

ENGINEERING/TECHNICAL PAGES PT10-44


DYNA-SYNC

SELECTION

H Stock Drive Selections 510H 10.33 12.91 15.46 19.24 20.50 17.22 19.75 21.00 15.69 18.99 20.25 17.46 19.49 15.93 20.75 .... 19.99 19.23 11.22 17.70 16.16 20.49 13.83 19.73 .... 14.06 16.40 17.94 19.47 20.23 .... 14.28 19.97 16.66 18.18 12.08 19.70 14.51 .... 12.30 16.86 .... 14.73 18.41 12.51 10.15

540H 11.85 14.42 16.97 20.75 22.00 18.73 21.25 22.50 17.20 20.49 21.75 18.97 20.99 17.44 22.25 .... 21.49 20.73 12.75 19.21 17.67 21.99 15.35 21.23 .... 15.58 17.91 19.45 20.87 21.73 10.94 15.80 21.47 18.14 19.68 13.63 21.21 16.03 .... 13.85 18.37 .... 16.25 19.92 14.07 11.77

570H 13.37 15.93 18.47 22.25 23.50 20.23 22.75 24.00 18.70 21.99 23.18 20.47 22.49 18.94 23.75 11.65 22.99 22.23 14.28 20.71 19.18 23.49 16.86 22.73 .... 17.09 19.42 20.95 22.48 23.23 12.51 17.32 22.98 19.65 21.19 15.17 22.72 17.55 .... 15.39 19.89 .... 17.77 21.43 15.61 13.36

600H 14.88 17.44 19.97 23.75 25.00 21.73 24.25 25.50 20.21 23.49 24.75 21.97 23.99 20.45 25.25 13.19 24.49 23.73 25.81 22.21 20.68 24.99 18.37 24.24 .... 18.61 20.92 22.45 23.98 24.74 14.07 16.64 24.46 21.16 22.69 16.70 24.22 19.07 12.18 16.93 21.39 .... 19.30 22.93 17.15 14.93

630H 16.40 18.94 21.47 25.25 26.50 23.23 25.75 27.01 21.71 24.99 26.25 23.48 25.49 21.95 26.75 14.73 26.00 25.24 17.32 23.72 22.19 26.49 19.88 25.74 12.94 20.35 22.43 23.96 25.48 26.24 15.61 20.35 25.98 22.67 24.20 18.23 25.72 20.58 13.78 18.45 22.90 .... 20.81 24.44 18.68 16.49

660H 17.91 20.45 22.97 26.75 28.00 24.74 27.25 28.50 23.22 26.49 27.75 24.98 26.99 23.46 28.25 16.25 27.49 26.74 18.84 25.22 23.69 27.99 21.39 27.24 14.50 21.63 23.93 25.46 26.98 27.74 17.15 21.86 27.48 24.17 25.70 19.75 27.22 22.09 15.35 19.98 24.41 .... 22.33 25.94 20.20 18.03

700H 19.92 22.45 24.98 28.75 30.01 26.74 29.25 30.51 25.22 28.50 29.75 26.98 29.00 25.46 30.25 18.28 29.50 28.74 20.85 27.22 25.70 30.00 23.40 29.24 16.56 23.64 25.94 27.47 28.99 29.74 19.19 23.87 29.48 26.18 27.71 21.78 29.23 24.11 17.43 22.01 26.42 .... 24.34 27.95 22.23 20.08

1.29 1-1/4 125

1.56 1-1/2 150

750H 22.43 24.96 27.48 31.25 32.51 29.24 31.75 33.01 27.72 31.00 32.25 29.48 31.50 27.97 32.75 20.81 32.00 31.24 23.37 29.73 28.21 32.50 25.91 31.74 19.12 26.15 28.45 29.97 31.48 32.24 21.73 26.39 31.99 28.69 30.21 24.30 31.73 26.62 20.01 24.53 28.92 15.43 26.86 30.45 24.76 22.63

800H 24.94 27.46 29.98 33.75 35.01 31.74 34.25 35.51 30.23 33.50 34.75 31.99 34.00 30.47 35.25 23.33 34.50 33.74 25.88 32.23 30.71 35.00 28.42 34.24 21.67 28.66 30.95 32.47 33.99 34.74 24.26 28.90 34.49 31.19 32.71 26.82 34.23 29.13 22.57 27.05 31.43 18.09 29.37 32.96 27.28 25.17

850H 900H 1000H 1100H 1250H 27.44 29.95 34.96 39.96 47.47 29.97 32.47 37.48 42.48 49.98 32.49 34.99 39.99 44.99 52.50 36.25 38.75 43.76 48.76 56.27 37.50 40.01 45.02 50.01 57.51 34.24 36.75 41.75 46.75 54.25 36.49 39.25 44.26 49.25 56.75 38.01 40.51 45.51 50.50 58.02 32.13 35.23 40.24 45.24 52.74 36.00 38.50 43.50 48.50 56.00 37.25 39.76 44.76 49.76 57.25 34.49 36.99 41.99 47.00 54.50 36.50 39.00 44.00 49.00 56.51 32.97 35.48 40.48 45.48 52.99 37.75 40.25 45.26 50.27 57.76 25.85 28.34 33.39 38.40 45.92 37.00 39.50 44.50 49.50 57.01 36.24 38.75 43.75 48.75 56.25 28.40 30.90 35.92 40.93 48.44 34.73 37.23 42.24 47.24 54.74 33.21 35.72 40.72 45.73 53.24 37.50 40.00 45.00 50.00 57.50 30.93 33.44 38.45 43.45♥ 50.96♥ 36.75 39.25 44.25 49.25 56.15 24.21 26.74 31.78 36.81 44.35 31.17 33.68 38.69♥ 43.70♥ 51.21♥ 33.46 35.96 40.97 45.97 53.48 34.97 37.48 42.48 47.48 54.99 36.49 38.99 43.99 49.00 56.50 37.25 39.75 44.75 49.75 57.25 26.78 29.30 34.33 39.35 46.88 31.41 33.91 38.93♥ 43.94♥ 51.45♥ 36.99 39.49 44.49 49.50 57.01 33.70 36.20 41.21 46.22 53.72 35.22 37.72 42.73 47.73 55.23 29.34 31.85 36.87 41.89♥ 49.41♥ 36.73 39.24 44.24 49.24 56.75 31.64 34.15♥ 39.17♥ 44.18♥ 51.69♥ 25.11 27.65 32.71 37.75 45.29 29.57 32.09 37.11 42.13♥ 49.65♥ 33.94 36.44 41.45 46.46 53.97 20.71 23.30 28.43 33.52 41.11 31.88♥ 34.39♥ 39.41♥ 44.42♥ 51.93♥ 35.46 37.97 42.97 47.97 55.48 29.80 32.32 37.35♥ 42.37♥ 49.89♥ 27.70 30.23 35.22 40.30 47.83♥

1400H 54.98 57.49♥ 60.00 63.75 65.01 61.75 64.26 65.51 60.25 63.52 64.76 62.00 64.01 60.49 65.25 53.43 64.50 63.75 55.95♥ 62.25 60.74 65.00 58.47♥ 64.14 51.87 58.71♥ 60.98 62.49 64.00 64.75 54.40♥ 58.95♥ 64.50 61.23 62.74 56.92♥ 64.25 59.20♥ 52.82♥ 57.16♥ 61.47 48.67 59.44♥ 62.98 57.40♥ 55.36♥

1700H 69.99♥ 72.49♥ 74.99 78.76 80.01 76.75 79.26 80.51 75.25 78.51 79.77 77.01 79.01 75.49 80.26 68.45♥ 79.51 78.77 70.97♥ 77.25 75.74 80.01 73.48♥ 79.25 66.90 73.73♥ 75.99 77.50 79.01 79.75 69.42♥ 73.97♥ 79.50 76.24 77.74 71.94♥ 79.25 74.21♥ 67.87♥ 72.19♥ 76.48 63.75♥ 74.46♥ 77.99 72.43♥ 70.39♥

8.89 7 700

10.32 8 800

H Belt Width Table Belt Width Factor Belt Width Belt Width Code

.42 1/2 050

.57 5/8 062

.71 3/4 075

.86 7/8 087

1.00 1 100

1.84 1-3/4 175

2.14 2 200

2.72 2-1/2 250

3.36 3 300

4.06 3-1/2 350

4.76 4 400

6.15 5 500

7.50 6 600

Sprockets

480H .... 11.40 13.95 17.74 19.00 15.72 18.24 19.50 14.19 17.48 18.74 15.96 17.96 14.42 19.24 .... 18.49 17.73 9.67 16.20 14.65 18.99 12.31 18.23 .... 12.53 14.89 16.43 17.97 18.73 .... 12.75 18.47 15.12 16.67 10.52 18.20 12.97 .... 10.76 15.35 .... 13.20 16.90 10.94 ....

Conveyor Components

450H .... 9.88 12.44 16.24 17.50 14.21 16.74 18.00 12.68 15.98 17.24 14.45 16.48 12.91 17.74 .... 16.98 16.22 .... 14.69 13.14 17.49 10.78 16.72 .... 11.00 13.37 14.92 16.46 17.22 .... 11.21 16.96 13.60 15.16 8.93 16.70 11.44 .... 9.14 13.83 .... 11.65 15.39 9.34 ....

HT Synchrous Belts

Nominal Center Distance Using DYNA-SYNC Belts

Engineering

Shaded area indicates stock belt widths.

FEATURES/BENEFITS PAGE PT10-2

PULLEY SPECIFICATIONS PAGES PT10-3

BELT SPECIFICATIONS PAGES PT10-11

PT10-33

ENGINEERING/TECHNICAL PAGES PT10-14


DYNA-SYNC

SELECTION

H Stock Drive Selections Driven Speeds for Motor Speeds of

HT Synchrous Belts Sprockets Conveyor Components

3500 1312 1283 1264 1250 .... 1167 1167 1167 1167 1167 .... 1094 1084 1069 1050 1021 .... 1000 972 948 933 .... 916 875 875 875 833 817 .... 802 .... 758 749 729 700 .... .... 656 642 583 .... .... 525 .... .... ....

1750 656 642 632 625 .... 583 583 583 583 583 583 547 542 535 525 510 .... 500 486 474 467 467 458 438 438 438 417 408 .... 401 389 379 375 365 350 .... 333 323 321 294 292 .... 262 .... 233 ....

1160 435 425 419 414 406 387 387 387 387 387 387 363 359 354 348 338 338 331 322 314 309 309 304 290 290 290 276 271 271 266 258 251 248 242 232 226 221 217 213 193 193 193 174 169 155 135

Speed Ratio 2.67 2.73 2.77 2.80 2.86 3.00 3.00 3.00 3.00 3.00 3.00 3.20 3.23 3.27 3.33 3.43 3.43 3.50 3.60 3.69 3.75 3.75 3.82 4.00 4.00 4.00 4.20 4.29 4.29 4.36 4.50 4.62 4.67 4.80 5.00 5.14 5.25 5.33 5.45 6.00 6.00 6.00 6.67 6.86 7.50 8.57

Pulley Combination Driver Driven No. of Pitch No. of Pitch Teeth Diam. Teeth Diam. 18H 2.865 48H 7.639 22H 3.501 60H 9.549 26H 4.138 72H 11.459 30H 4.775 84H 13.369 14H 2.228 40H 6.366 40H 6.366 120H 19.099 32H 5.093 96H 15.279 28H 4.456 84H 13.369 24H 3.820 72H 11.459 20H 3.183 60H 9.549 16H 2.546 48H 7.639 30H 4.775 96H 15.279 26H 4.138 84H 13.369 22H 3.501 72H 11.459 18H 2.865 60H 9.549 28H 4.456 96H 15.279 14H 2.228 48H 7.639 24H 3.820 84H 13.369 20H 3.183 72H 11.459 26H 4.138 96H 15.279 32H 5.093 120H 19.099 16H 2.546 60H 9.549 22H 3.501 84H 13.369 30H 4.775 120H 19.099 24H 3.820 96H 15.279 18H 2.865 72H 11.459 20H 3.183 84H 13.369 28H 4.456 120H 19.099 14H 2.228 60H 9.549 22H 3.501 96H 15.279 16H 2.546 72H 11.459 26H 4.138 120H 19.099 18H 2.865 84H 13.369 20H 3.183 96H 15.279 24H 3.820 120H 19.099 14H 2.228 72H 11.459 16H 2.546 84H 13.369 18H 2.865 96H 15.279 22H 3.501 120H 19.099 20H 3.183 120H 19.099 16H 2.546 96H 15.219 14H 2.228 84H 13.369 18H 2.865 120H 19.099 14H 2.228 96H 15.279 16H 2.546 120H 19.099 14H 2.228 120H 19.099

HP for a 1 Wide Belt for Motor Speeds of Δ 3500 10.71◊ 12.84 14.80 16.59 .... 20.08 17.40 15.74 13.82 11.77◊ .... 16.59 14.80 12.84 10.71◊ 15.74 .... 13.82 11.77◊ 14.80 17.40 .... 12.84 16.59 13.82 10.71◊ 11.77◊ 15.74 .... 12.84 .... 14.80 10.71◊ 11.71◊ 13.82 .... .... 10.71◊ 12.84 11.77◊ .... .... 10.71◊ .... .... ....

1750 5.52◊ 6.71 7.88 9.03 .... 11.79 9.60 8.46 7.30 6.11 4.91◊ 9.03 7.88 6.71 5.52◊ 8.46 .... 7.30 6.11 7.88 9.60 4.91◊ 6.71 9.03 7.30 5.52◊ 6.11 8.46 .... 6.71 4.91◊ 7.88 5.52 6.11 7.30 .... 4.91◊ 5.52◊ 6.71 6.11 4.91◊ .... 5.52◊ .... 4.91◊ ....

Δ HP ratings are for conventional speed-reduction drives. For Speed-Up Drives refer to page PT10-17. ◊ Pulley Diameter is below recommended minimum. A reduction in belt life should be expected. Suggest alternate drive selection, whenever possible.

1160 3.68 4.48 5.28 6.08 2.86◊ 8.03 6.48 5.68 4.89 4.08 3.27◊ 6.08 5.28 4.48 3.68 5.68 2.86◊ 4.89 4.08 5.28 6.48 3.27◊ 4.48 6.08 4.89 3.68 4.08 5.68 2.86◊ 4.48 3.27◊ 5.28 3.68 4.08 4.89 2.86◊ 3.27◊ 3.68 4.48 4.08 3.27◊ 2.86◊ 3.68◊ 3.27◊ 2.86◊ ....

Nominal C.D. Using DYNA-SYNC Belts 240H .... .... .... .... 4.80† .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ....

270H .... .... .... .... 6.42† .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ....

300H 6.30 .... .... .... 7.99† .... .... .... .... .... 6.50 .... .... .... .... .... 6.70† .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ....

330H 7.89 .... .... .... 9.53 .... .... .... .... .... 8.10 .... .... .... .... .... 8.95† .... .... .... .... .... .... .... .... .... .... .... 6.12‡ .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ....

360H 9.45 7.10 .... .... 11.06 .... .... .... .... 7.30 9.67 .... .... .... 7.50 .... 9.88† .... .... .... .... 7.69† .... .... .... .... .... .... 7.89‡ .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ....

390H 420H 11.00 12.53 8.73 10.31 .... .... .... .... 12.59 14.11 .... .... .... .... .... .... .... 8.08 8.93 10.52 11.22 12.75 .... .... .... .... .... 8.28 9.14 10.77 .... .... 11.44† 12.98 .... .... .... 8.47 .... .... .... .... 9.34† 10.94 .... .... .... .... .... .... .... 8.67 .... .... .... .... 9.55† 11.15† .... .... .... 8.86† .... .... .... .... .... .... .... .... 7.22§ 9.05‡ .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ....

† ‡ § See Teeth in Mesh table on opposite page. ♥ Flanges Required on both pulleys.

Engineering FEATURES/BENEFITS PAGE PT10-2

PULLEY SPECIFICATIONS PAGES PT10-3

BELT SPECIFICATIONS PAGES PT10-11

PT10-34

ENGINEERING/TECHNICAL PAGES PT10-44


DYNA-SYNC

SELECTION

H Stock Drive Selections 540H 18.61 16.48 14.29 11.98 20.15 .... .... 12.18 14.50 16.70 18.84 .... 12.39 14.72 16.93 .... 19.07 12.59 14.93 10.19 .... 17.15 12.79 .... 10.38 15.14 12.99 .... 17.37 10.57 15.36 .... 13.20 10.75 .... 15.57† 13.40 10.94† .... .... 11.13‡ 13.60† 11.31‡ .... .... ....

570H 20.35 18.00 15.83 13.57 21.66 .... 11.34 13.78 16.05 18.23 20.35 11.54 13.99 16.27 18.46 11.73 20.58 14.20 16.49 11.93 .... 18.86 14.40 .... 12.12 16.70 14.61 .... 21.95♥ 12.32 16.92 .... 14.82 12.51 .... 17.13† 15.02 12.71† .... .... 12.90 15.23† 13.09‡ .... .... ....

600H 21.63 19.52 17.37 15.14 23.17 .... 12.99 15.36 17.59 19.75 21.86 13.20 15.57 17.81 19.98 13.40 22.09 15.78 18.03 13.60 .... 21.20 15.99 .... 13.80 18.25 16.20 .... 18.90♥ 14.00 18.47 .... 15.41 14.20 .... 18.69†♥ 16.62 14.40 .... .... 14.59† 16.83† .... 14.79‡ .... ....

.57 5/8 062

.71 3/4 075

630H 23.14 21.04 18.90 16.70 23.67 .... 14.81 16.92 19.13 21.27 23.37 14.81 17.13 19.35 21.50 15.02 23.61 17.35 19.57 15.23 .... 21.73♥ 17.56 .... 15.43 19.79 17.77 .... 20.43♥ 15.63 20.01 .... 17.99 15.84 .... 20.23†♥ 18.20 16.04 .... .... 16.24† 18.41†♥ .... 16.44† .... 11.49§

660H 24.64 22.56 20.43 18.25 26.18 .... 16.20 18.47 20.65 22.79 24.88 16.41 18.68 20.88 23.02♥ 16.62 25.11 18.90 21.10 16.83 .... 23.26♥ 19.12 .... 17.03 21.32 19.33 .... 23.47♥ 17.24 21.55♥ 12.43 19.55 17.45 .... 21.77♥ 19.76 17.65 12.79 12.98† 17.86 19.98†♥ 13.16† 18.07†♥ 13.64‡ 13.53§

700H 26.65 24.58 22.46 20.30 28.19 13.47 18.29 20.52 22.69 24.81 26.89 18.51 20.74 22.91 25.04♥ 18.72 27.13 20.96 23.14 18.93 14.25 25.27♥ 21.18 14.44 19.14 23.36♥ 21.40 14.63 25.50♥ 19.36 23.59♥ 14.82 21.62 19.57 15.02 23.81♥ 21.84♥ 19.78 15.21 15.40 19.99 22.05†♥ 15.59† 20.19†♥ 15.78† 15.97‡

750H 29.16 27.09 24.99 22.85 30.69 16.24 20.88 23.08 26.22 27.32♥ 29.40 21.10 23.30 25.45 27.56♥ 21.32 29.64 23.52 25.68♥ 21.53 17.05 27.79♥ 23.74 17.25 21.75 25.90♥ 23.97 17.45 28.02♥ 21.96 26.13♥ 17.65 24.19♥ 22.18 17.84 26.35♥ 24.39♥ 22.39 18.04 18.24 22.61♥ 24.63†♥ 18.44 22.82†♥ 18.64† 18.83‡♥

800H 31.67 29.61♥ 27.52 25.39 33.20 18.92 23.45 25.62 27.75 29.84♥ 31.91 23.67 25.85 27.98 30.07♥ 23.89 32.15 26.07 28.21♥ 24.11 19.75 30.31♥ 26.30 19.96 24.33 28.44♥ 26.52♥ 20.16 30.54♥ 24.55 28.66♥ 20.37 26.74♥ 24.77 20.57 28.89♥ 26.96♥ 24.98♥ 20.78 20.98 25.20♥ 27.19♥ 21.18 25.42†♥ 21.38†♥ 21.59†♥

850H 34.18 32.12♥ 30.04 27.95 35.70 21.56 26.01 28.16 30.27 32.35♥ 34.42 26.23 28.38 30.50♥ 32.59♥ 26.45 34.68 28.61 30.73♥ 26.67 22.40 32.82♥ 28.84♥ 22.61 27.00 30.96♥ 29.06♥ 22.82 33.06♥ 27.12 31.19♥ 23.03 29.29♥ 27.34♥ 23.24 31.42♥ 29.51♥ 27.56♥ 23.45 23.66 27.78♥ 29.74♥ 23.86♥ 27.99†♥ 24.07♥ 24.28†♥

900H 36.68 34.63♥ 32.55 30.46 38.21 24.16 28.55 30.69 32.79♥ 38.87♥ 36.92 28.79 30.91 33.02♥ 35.10♥ 29.00 37.16 31.14♥ 33.25♥ 29.23 25.02 35.34♥ 31.37♥ 25.23 29.45 33.48♥ 31.60♥ 25.45 35.57♥ 29.67♥ 33.72♥ 25.66 31.83♥ 29.90♥ 25.87 33.95♥ 32.08♥ 30.12♥ 26.08 26.29♥ 30.34♥ 32.28♥ 26.51♥ 30.56†♥ 26.72♥ 26.93†♥

1000H 41.69 39.65♥ 37.58♥ 35.50 43.21 29.31 33.62 35.73♥ 37.82♥ 39.88♥ 41.93 33.85 35.96♥ 38.05♥ 40.12♥ 34.08 42.17 36.20♥ 38.29♥ 34.31♥ 30.19 40.36♥ 36.43♥ 30.41 34.53♥ 38.52♥ 36.66♥ 30.63 40.60♥ 34.76♥ 38.75♥ 30.85 36.89♥ 34.99♥ 31.06♥ 38.99♥ 37.12♥ 35.21♥ 31.28♥ 31.50♥ 35.44♥ 37.34♥ 31.71♥ 35.66♥ 31.93♥ 32.14†♥

1100H 46.70 44.66♥ 42.60♥ 40.53♥ 48.22 34.42 38.67 40.77♥ 42.84♥ 44.90♥ 46.94 38.90♥ 41.00♥ 43.08♥ 45.14♥ 39.13♥ 47.18 41.23♥ 43.31♥ 39.36♥ 35.31 45.38♥ 41.47♥ 35.53 39.59♥ 43.55♥ 41.70♥ 35.76♥ 45.61♥ 39.82♥ 43.78♥ 35.98♥ 41.93♥ 40.05♥ 36.20♥ 44.02♥ 42.16♥ 40.28♥ 36.42♥ 36.64♥ 40.51♥ 42.39♥ 36.86♥ 40.74♥ 37.08♥ 37.30♥

1250H 54.21 52.17♥ 50.13♥ 48.07♥ 55.72 42.03 46.23♥ 48.31♥ 50.37♥ 52.42♥ 54.45 46.46♥ 48.54♥ 50.61♥ 52.66♥ 46.70♥ 54.70 48.78♥ 50.84♥ 46.93♥ 42.94♥ 52.90♥ 49.01♥ 43.16♥ 47.16♥ 51.08♥ 49.25♥ 43.39♥ 53.14♥ 47.39♥ 51.32♥ 43.62♥ 49.48♥ 47.63♥ 43.84♥ 51.55♥ 49.72♥ 47.86♥ 44.07♥ 44.29♥ 48.09♥ 49.95♥ 44.52♥ 48.32♥ 44.74♥ 44.97♥

1400H 61.71 56.69♥ 57.64♥ 55.59♥ 63.23 49.60 53.77♥ 55.83♥ 57.88♥ 59.93♥ 81.96 54.00♥ 56.07♥ 58.12♥ 60.17♥ 54.24♥ 62.20 56.35♥ 58.36♥ 54.48♥ 50.52♥ 60.41♥ 56.54♥ 50.75♥ 54.71♥ 58.60♥ 56.78♥ 50.98♥ 60.65♥ 54.94♥ 58.84♥ 51.21♥ 57.02♥ 55.18♥ 51.44♥ 59.08♥ 57.25♥ 55.41♥ 51.67♥ 51.90♥ 55.65♥ 57.49♥ 52.13♥ 55.88♥ 52.35♥ 52.58♥

1700H 76.73 74.70♥ 72.67♥ 70.63♥ 78.24 64.70♥ 68.62♥ 70.87♥ 72.91♥ 94.95♥ 76.97 69.06♥ 71.11♥ 73.15♥ 75.19♥ 69.30♥ 77.22♥ 71.35♥ 73.40♥ 69.54♥ 65.64♥ 75.43♥ 71.59♥ 65.87♥ 69.78♥ 73.64♥ 71.83♥ 66.11♥ 75.67♥ 70.01♥ 73.88♥ 66.34♥ 72.07♥ 70.25♥ 66.57♥ 74.12♥ 72.31♥ 70.49♥ 66.81♥ 67.04♥ 70.73♥ 72.55♥ 67.27♥ 70.96♥ 67.50♥ 67.74♥

7.50 6 600

8.89 7 700

10.32 8 800

H Belt Width Table Belt Width Factor Belt Width Belt Width Code

.42 1/2 050

.86 7/8 087

1.00 1 100

1.29 1-1/4 125

1.56 1-1/2 150

1.84 1-3/4 175

2.14 2 200

Teeth in Mesh factor (T.I.M.) Table Symbol None †

3.36 3 300

4.06 3-1/2 350

4.76 4 400

6.15 5 500

Shaded area indicates stock belt widths.

No. of Teeth In Mesh In Small Pulley 6 or More 5

FEATURES/BENEFITS PAGE PT10-2

2.72 2-1/2 250

Sprockets

510H 17.09 14.95 12.73 10.35 18.65 .... .... 10.55 12.94 15.17 17.32 .... 10.75 13.15 15.39 .... 17.55 10.95 13.36 .... .... 15.61 11.14 .... .... 13.57 11.34 .... 15.83† .... 13.78 .... 11.54 .... .... 13.99† 11.73† .... .... .... 9.20§ 11.93‡ 9.37§ .... .... ....

Conveyor Components

480H 15.58 13.42 11.15 .... 17.13 .... .... .... 11.36 13.63 15.80 .... 9.05 11.56 13.85 .... 16.03 9.24 11.77 .... .... 14.07 9.43 .... .... 11.98 9.62 .... 14.29† .... 12.1† .... 9.81† .... .... 12.39† 10.00† .... .... .... .... 10.19‡ .... .... .... ....

Factor 1.00 .80

Table Symbol ‡ §

PULLEY SPECIFICATIONS PAGES PT10-3

No. of Teeth In Mesh In Small Pulley 4 3

BELT SPECIFICATIONS PAGES PT10-11

PT10-35

Factor .60 .40

ENGINEERING/TECHNICAL PAGES PT10-14

Engineering

450H 14.06 11.87 9.55 .... 15.62 .... .... .... 9.75 12.09 14.28 .... .... 9.95 12.30 .... 14.51 .... 10.15 .... .... 12.51 .... .... .... 10.35 .... .... 12.73† .... 10.55† .... .... .... .... 10.75† .... .... .... .... .... 8.30§ .... .... .... ....

HT Synchrous Belts

Nominal Center Distance Using DYNA-SYNC Belts


DYNA-SYNC

SELECTION

XH Stock Drive Selections Pulley Combination

Driven Speeds for Motor Speeds of

HT Synchrous Belts

1750 1750 1750 1750 1750 1750 1750 1750 1750 1641 1633 1625 1615 1604 1591 1531 1517 1500 1481 1458 1458

Sprockets

1422 1400 1400 1375 1346 1313 1313 1283 1250 1225

Conveyor Components

1203 1167 1167 1167 1138 1094 1094 1050 1021 972 963

1160 1160 1160 1160 1160 1160 1160 1160 1160 1160 1088 1083 1077 1071 1063 1055 1044 1015 1005 994 982 967 967 949 943 928 928 911 892 870 870 870 851 829 812 803 798 773 773 773 754 746 725 725 696 696 677 653 644 638

Speed Ratio 870 870 870 870 870 870 870 870 870 870 816 812 808 803 798 791 783 761 754 746 736 725 725 712 707 696 696 684 669 653 653 653 638 621 609 602 598 580 580 580 566 559 544 544 522 522 508 489 483 479

1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.07 1.07 1.08 1.08 1.09 1.10 1.11 1.14 1.15 1.17 1.18 1.20 1.20 1.22 1.23 1.25 1.25 1.27 1.30 1.33 1.33 1.33 1.36 1.40 1.43 1.44 1.45 1.50 1.50 1.50 1.54 1.56 1.60 1.60 1.67 1.67 1.71 1.78 1.80 1.82

Driver No. of Teeth 40XH 32XH 30XH 28XH 26XH 24XH 22XH 20XH 18XH 30XH 28XH 26XH 24XH 22XH 20XH 18XH 28XH 26XH 24XH 22XH 40XH 20XH 18XH 26XH 32XH 24XH 22XH 20XH 30XH 24XH 18XH 22XH 20XH 28XH 18XH 22XH 40XH 32XH 20XH 26XH 18XH 30XH 20XH 24XH 18XH 28XH 18XH 40XH 22XH

Driven Pitch Diam. 11.141 8.913 8.356 7.799 7.241 6.685 6.127 5.570 5.013 8.356 7.799 7.241 6.685 6.127 5.570 5.013 7.799 7.241 6.685 6.127 11.141 5.570 5.013 7.241 8.913 6.685 6.127 5.570 8.356 6.685 5.013 6.127 5.570 7.799 5.013 6.127 11.141 8.913 5.570 7.241 5.013 8.356 5.570 6.685 5.013 7.799 5.013 11.141 6.127

Engineering

Δ HP ratings are for conventional speed-reduction drives. For Speed-Up Drives refer to page PT10-17. ◊ Pulley Diameter is below recommended minimum. A reduction in belt life should be expected. Suggest alternate drive selection, whenever possible.

FEATURES/BENEFITS PAGE PT10-2

PULLEY SPECIFICATIONS PAGES PT10-3

No. of Teeth 40XH 32XH 30XH 28XH 26XH 24XH 22XH 20XH 18XH 32XH 30XH 28XH 26XH 24XH 22XH 20XH 32XH 30XH 28XH 26XH 48XH 24XH 22XH 32XH 40XH 30XH 28XH 26XH 40XH 32XH 24XH 30XH 28XH 40XH 26XH 32XH 60XH 48XH 30XH 40XH 28XH 48XH 32XH 40XH 30XH 48XH 32XH 72XH 40XH

Pitch Diam. 11.141 8.913 8.356 7.799 7.241 6.685 6.127 5.570 5.013 8.913 8.356 7.799 7.241 6.685 6.127 5.570 8.913 8.356 7.799 7.241 13.369 6.685 6.127 8.913 11.141 8.356 7.799 7.241 11.141 8.913 6.685 8.356 7.799 11.141 7.241 8.913 16.711 13.369 8.356 11.141 7.799 13.369 8.913 11.141 8.356 13.369 8.913 20.054 11.141

1750 22.22 19.87 19.06 18.16 17.17 16.14◊ 15.03◊ 13.85◊ .... 19.06 18.16 17.17 16.14◊ 15.03◊ 13.85◊ .... 18.16 17.17 16.14◊ 15.03◊ 22.22 13.85 .... 17.17 19.87 16.14◊ 15.03◊ 13.85◊ 19.06 16.14◊ .... 15.03◊ 13.85◊ 18.16 .... 15.03◊ 22.22 19.87 13.85◊ 17.17 .... 19.06 13.85◊ 16.14◊ .... 18.16 .... 22.22 15.03◊

1160 17.44 14.57 13.79 12.97 12.13 11.29◊ 10.41◊ 9.51◊ 8.61 13.79 12.97 12.13 11.29 10.41◊ 9.51◊ 8.61◊ 12.97 12.13 11.29 10.41◊ 17.44 9.51◊ 8.61◊ 12.13 14.57 11.29 10.41◊ 9.51◊ 13.79 11.29 8.61◊ 10.41◊ 9.51◊ 12.97 8.61◊ 10.41◊ 17.44 14.57 9.51◊ 12.13 8.61◊ 13.79 9.51◊ 11.29 8.61◊ 12.97 8.61◊ 17.44 10.41◊

870 13.79 11.29 10.63 9.97 9.29 8.61 7.92 7.23◊ 6.52◊ 10.63 9.97 9.29 8.61 7.92 7.23◊ 6.52◊ 9.97 9.29 8.61 7.92 13.79 7.23◊ 6.52◊ 9.29 11.29 8.61 7.92 7.23◊ 10.63 8.61 6.52◊ 7.92 7.23◊ 9.97 6.52◊ 7.92 13.79 11.29 7.23◊ 9.29 6.52◊ 10.63◊ 7.23◊ 8.61 6.52◊ 9.97 6.52◊ 13.79 7.92

♥ Flanges Required on both pulleys.

BELT SPECIFICATIONS PAGES PT10-11

PT10-36

HP for a 1 Wide Belt for Motor Speeds of Δ

ENGINEERING/TECHNICAL PAGES PT10-44


DYNA-SYNC

SELECTION

XH Stock Drive Selections

14.37 10.76 15.24 .... 13.89 11.15 14.78 .... 14.30 .... 11.54

17.00 13.42 17.88 .... 16.54 13.82 17.42 11.02 16.95 .... 14.21

13.53 14.41 15.29

630XH 14.00 17.50 18.37 19.25 20.12 21.00 21.87 22.75 23.62 17.93 18.81 19.68 20.56 21.43 22.31 23.18 18.36 19.24 20.11 20.99 .... 21.86 22.74 18.79 15.71 19.67 20.54 21.42 16.12 19.21 22.29 20.09 20.97 16.54 21.84 19.63 .... 13.82 20.51 16.95 21.39 14.21 20.05 17.35 20.93 14.60 20.47 .... 17.76

700XH 17.50 21.00 21.87 22.75 23.62 24.50 25.37 26.25 27.12 21.43 22.31 23.18 24.06 24.93 25.81 26.68 21.86 22.74 23.61 24.49 15.71 25.36 26.24 22.29 19.21 23.17 24.04 24.92 19.63 22.72 25.79 23.59 24.47 20.05 25.35 23.14 .... 17.35 24.02 20.47 24.89 17.76 23.56 20.88 24.44 18.16 23.98 .... 21.29

770XH 21.00 24.50 25.37 26.25 27.12 28.00 28.87 29.75 30.62 24.93 25.81 26.68 27.56 28.43 29.31 30.18 25.36 26.24 27.12 27.99 19.21 28.87 29.74 25.79 22.72 26.67 27.55 28.42 23.14 26.22 29.30 27.10 27.97 23.56 28.85 26.65 16.38 20.88 27.52 23.98 28.40 21.29 27.07 24.39 27.95 21.69 27.49 .... 24.81

840XH 24.50 28.00 28.87 29.75 30.62 31.50 32.37 33.25 34.12 28.43 29.31 30.18 31.06 31.93 32.81 33.68 28.87 29.74 30.62 31.49 22.72 32.37 33.24 29.30 26.22 30.17 31.05 31.92 26.65 29.72 32.80 30.60 31.48 27.07 32.35 30.15 19.93 24.39 31.03 27.49 31.90 24.81 30.58 27.91 31.45 25.22 31.00 16.90 28.32

980XH 31.50 35.00 35.87 36.75 37.62 38.50 39.37 40.25 41.12 35.43 36.31 37.18 38.06 38.93 39.81 40.68 35.87 36.74 37.62 38.49 29.72 39.37 40.24 36.30 33.23 37.17 38.05 38.92 33.65 36.73 39.80 37.60 38.48 34.08 39.35 37.16 26.98 31.42 38.03 34.50 38.91 31.83 37.58 34.92 38.45 32.25 38.01 24.08 35.34

1120XH 38.50 42.00 42.87 43.75 44.62 45.50 46.37 47.25 48.12 42.43 43.31 44.18 45.06 45.93 46.81 47.68 42.87 43.74 44.62 45.49 36.73 46.37 47.24 43.30 40.23 44.18 45.05 45.93 40.66 43.73 46.80 44.61 45.48 41.09 46.36 44.16 34.01 38.43 45.04 41.50 45.91 38.85 44.59 41.94 38.46 39.27 45.02 31.18 42.36

1260XH 45.50 49.00 49.87 50.75 51.62 52.50 53.37 54.25 55.12 49.43 50.31 51.18 52.06 52.93 53.81 54.68 49.87 50.74 51.62 52.49 43.73 53.37 54.24 50.30 47.23 51.18 52.05 52.93 47.66 50.73 53.80 51.61 52.48 48.09 53.36 51.16 41.03 45.44 52.04 48.52 52.91 45.86 51.59 48.94 52.47 46.29 52.02 38.24 49.37

1400XH 52.50 56.00 56.87 57.75 58.62 59.50 60.37 61:25 62.12 56.43 57.31 58.18 59.06 59.93 60.81 61.68 56.87 57.74 58.62 59.49 50.73 60.37 61.24 57.30 54.23 58.18 59.05 59.93 54.67 57.74 60.80 58.61 59.49 55.10 60.36 58.17 48.04 52.45 59.04 55.52 59.92 52.87 58.60 55.95 59.47 53.30 59.03 45.28 56.38

1540XH 59.50 83.00 83.87 64.75 65.62 66.50 67.37 68.25 69.12 83.43 64.31 65.18 66.06 66.93 67.81 68.68 83.87 64.74 65.62 66.49 57.74 67.37 68.24 64.30 61.24 65.18 66.05 66.93 61.67 64.74 67.80 65.61 66.49 62.10 67.36 65.17 55.05 59.45 66.04 62.53 66.92 59.88 65.60 62.96 66.47 60.31 66.03 52.31 83.38

1750XH 70.00 73.50 74.37 75.25 76.12 77.00 77.87 78.75 79.62 73.93 74.81 75.68 76.56 77.43 78.31 79.18 74.37 75.24 76.12 76.99 68.24 77.87 78.74 74.80 71.74 75.68 76.55 77.43 72.17 75.24 78.30 76.11 76.99 72.60 77.86 75.67 65.56 69.96 76.55 73.03 77.42 70.39♥ 76.10 73.46 76.98 70.82♥ 76.53 62.84 73.89

Sprockets

13.07 16.16 13.95 14.83 10.36 15.71 13.49 ....

560XH .... 14.00 14.87 15.75 16.62 17.50 18.37 19.25 20.12 14.43 15.31 16.18 17.06 17.93 18.81 19.68 14.86 15.74 16.61 17.49 .... 18.36 19.24 15.29 12.19 16.16 17.04 17.91 12.61 15.71 18.79 16.58 17.46 13.01 18.34 16.12 ....

Conveyor Components

507XH .... 11.37 12.25 13.12 14.00 14.87 15.75 16.62 17.50 11.80 12.68 13.56 14.43 15.31 16.18 17.06 12.23 13.11 13.98 14.66 .... 15.74 16.61 12.66

HT Synchrous Belts

Nominal Center Distance Using DYNA-SYNC Belts

XH Belt Width Table Belt Width Factor 1.00 Belt Width 1 Belt Width Code 100

1.29 1-1/4 125

1.56 1-1/2 150

1.84 1-3/4 175

2.14 2 200

2.72 2-1/2 250

3.36 3 300

4.06 3-1/2 350

4.76 4 400

6.15 5 500

7.50 6 600

8.89 7 700

10.32 11.70 13.10 14.41 15.84 17.16 18.62 8 9 10 11 12 13 14 800 900 1000 1100 1200 1300 1400

FEATURES/BENEFITS PAGE PT10-2

Engineering

Shaded area indicates stock belt widths.

PULLEY SPECIFICATIONS PAGES PT10-3

BELT SPECIFICATIONS PAGES PT10-11

PT10-37

ENGINEERING/TECHNICAL PAGES PT10-14


DYNA-SYNC

SELECTION

XH Stock Drive Selections Pulley Combination

Driven Speeds for Motor Speeds of

HT Synchrous Belts Sprockets Conveyor Components

1750 948 933 875 875 875 833 817 802 .... 778 758 729 729 729 700 681 667 .... 642 632 625 583 583 583 583 583 547 542 535 .... 510 500 486 474 467 458 438 438 .... 416 408 401 379 .... 365 350 .... 321 292 ....

1160 628 618 580 580 580 552 541 531 523 516 502 483 483 483 464 451 442 434 425 419 414 387 387 387 387 387 363 359 355 348 338 331 322 314 309 304 290 290 290 276 270 266 251 249 242 232 217 212 193 174

Speed Ratio 870 471 464 435 435 435 414 407 399 392 387 377 363 363 363 348 339 331 326 319 314 311 290 290 290 290 290 272 269 266 261 254 249 242 236 232 228 218 218 218 207 203 200 188 186 181 174 162 159 145 130

1.85 1.88 2.00 2.00 2.00 2.10 2.14 2.18 2.22 2.25 2.31 2.40 2.40 2.40 2.50 2.57 2.63 2.67 2.73 2.77 2.80 3.00 3.00 3.00 3.00 3.00 3.20 3.23 3.27 3.33 3.43 3.50 3.60 3.69 3.75 3.82 4.00 4.00 4.00 4.20 4.29 4.36 4.62 4.67 4.80 5.00 5.33 5.45 6.00 6.67

Driver No. of Teeth 26XH 32XH 30XH 24XH 20XH 40XH 28XH 22XH 18XH 32XH 26XH 40XH 30XH 20XH 24XH 28XH 32XH 18XH 22XH 26XH 30XH 40XH 32XH 28XH 24XH 20XH 30XH 26XH 22XH 18XH 28XH 24XH 20XH 26XH 32XH 22XH 30XH 24XH 18XH 20XH 28XH 22XH 26XH 18XH 20XH 24XH 18XH 22XH 20XH 18XH

Driven Pitch Diam. 7.241 8.913 8.356 6.685 5.570 11.141 7.799 6.127 5.013 8.913 7.241 11.141 8.356 5.570 6.685 7.799 8.913 5.013 6.127 7.241 8.356 11.141 8.913 7.799 6.685 5.570 8.356 7.241 6.127 5.013 7.799 6.685 5.570 7.241 8.913 6.127 8.356 6.685 5.013 5.570 7.799 6.127 7.241 5.013 5.570 6.685 5.013 6.127 5.570 5.013

Engineering

Δ HP ratings are for conventional speed-reduction drives. For Speed-Up Drives refer to page PT10-17. ◊ Pulley Diameter is below recommended minimum. A reduction in belt life should be expected. Suggest alternate drive selection, whenever possible.

FEATURES/BENEFITS PAGE PT10-2

PULLEY SPECIFICATIONS PAGES PT10-3

No. of Teeth 48XH 60XH 60XH 48XH 40XH 84XH 60XH 48XH 40XH 72XH 60XH 96XH 72XH 48XH 60XH 72XH 84XH 48XH 60XH 72XH 84XH 120XH 96XH 84XH 72XH 60XH 96XH 84XH 72XH 60XH 96XH 84XH 72XH 96XH 120XH 84XH 120XH 98XH 72XH 84XH 120XH 96XH 120XH 84XH 96XH 120XH 96XH 120XH 120XH 120XH

Pitch Diam. 13.369 16.711 16.711 13.369 11.141 23.396 16.711 13.369 11.141 20.054 16.711 26.738 20.054 13.369 16.711 20.054 23.396 13.369 16.711 20.054 23.396 33.423 26.738 23.396 20.054 16.711 26.738 23.396 20.054 16.711 26.738 23.396 20.054 26.738 33.423 23.396 33.423 26.738 20.054 23.396 33.423 26.738 33.423 23.396 26.738 33.423 26.738 33.423 33.423 33.423

1750 17.17 19.87 19.06 16.14◊ 13.85◊ 22.22 18.16 15.03◊ .... 19.87 17.17 22.22 19.06 13.85◊ 16.14◊ 18.16 19.87 .... 15.03◊ 17.17 19.06 22.22 19.87 18.16 16.14◊ 13.85◊ 19.06 17.17 15.03◊ .... 18.16 16.14◊ 13.85◊ 17.17 19.87 15.03◊ 19.06 16.14◊ .... 13.85◊ 18.16 15.03◊ 17.17 .... 13.85◊ 16.14◊ .... 15.03 13.85◊ ....

1160 12.13 14.57 13.79 11.29 9.51◊ 17.44 12.97 10.41◊ 8.61◊ 14.57 12.13 17.44 13.79 9.51◊ 11.29 12.97 14.57 8.61◊ 10.41◊ 12.13 13.79 17.44 14.57 12.97 11.29 9.51◊ 13.79 12.13 10.41◊ 8.61◊ 12.97 11.29 9.51◊ 12.13 14.57 10.41 13.79◊ 11.29 8.61◊ 9.51◊ 12.97 10.41◊ 12.13 8.61◊ 9.51◊ 11.29 8.61◊ 10.41◊ 9.51◊ 8.61◊

870 9.29 11.29 10.63 8.61 7.23◊ 13.79 9.97 7.92 6.52◊ 11.29 9.29 13.79 10.63 7.23◊ 8.61 9.97 11.29 6.52◊ 7.92 9.29 10.63 13.79 11.29 9.97 8.61 7.23◊ 10.63 9.29 7.92 6.52◊ 9.97 8.61 7.23◊ 9.29 11.29 7.92 10.63 8.61 6.52◊ 7.23◊ 9.97 7.92 9.29 6.52◊ 7.23◊ 8.61 6.52◊ 7.92 7.23◊ 6.52◊

† ‡ See Teeth in Mesh table on opposite page. ♥ Flanges Required on both pulleys.

BELT SPECIFICATIONS PAGES PT10-11

PT10-38

HP for a 1 Wide Belt for Motor Speeds of Δ

ENGINEERING/TECHNICAL PAGES PT10-44


DYNA-SYNC

SELECTION

XH Stock Drive Selections 630XH 14.99 .... .... 15.38 18.16 .... .... 15.77 18.55 .... .... .... .... 16.15 .... .... .... 16.53 12.41 .... .... .... .... .... .... 12.76 .... .... .... 13.11 .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ....

700XH 18.55 14.34 14.71 18.95 21.69 .... 15.08 19.34 22.10 .... 15.45 .... .... 19.73 15.82 .... .... 20.12 16.19 .... .... .... .... .... .... 16.55 .... .... .... 16.91 .... .... .... .... .... .... .... .... 13.08† .... .... .... .... .... .... .... .... .... .... ....

770XH 22.10 17.95 18.33 22.50 25.22 .... 18.71 22.90 25.83 .... 19.09 .... 15.03 23.29 19.47 15.38 .... 23.69 19.85 15.74 .... .... .... .... 16.09 20.22 .... .... 16.44 20.60 .... .... 16.78 .... .... .... .... .... 17.13 .... .... .... .... .... .... .... .... .... .... ....

840XH 25.63 21.52 21.91 26.03 28.74 .... 22.30 26.43 29.15 18.40 22.69 .... 18.76 26.84 23.07 19.13 .... 27.24 23.46 19.50 .... .... .... .... 19.86 23.84 .... 15.82 20.22 24.22 .... 16.16 20.58 .... .... 16.49 .... .... 20.94 16.83 .... .... .... 17.16† .... .... .... .... .... ....

980XH 32.66 28.60 29.01 33.08 35.76 20.97 29.41 33.49 36.18 25.64 29.81 .... 26.02 33.90 30.20 26.41 22.44 34.30 30.60 26.79 22.81 .... 18.85 23.17 27.17 30.99 19.19 27.55 23.53 31.39 19.53 23.89 27.93 19.87 .... 24.25 .... 20.20 28.30 24.61 .... 20.54 .... 24.97 20.88 .... 21.21 .... .... ....

1120XH 39.69 35.66 36.07 40.11 42.78 28.20 36.47 40.52 43.20 32.77 36.88 25.02 33.17 40.94 37.28 33.56 29.73 41.35♥ 37.69 33.95 30.11 .... 26.48 30.49 34.34 38.09 26.84 34.73 30.87 38.49 27.21 31.25 35.12 27.57 .... 31.62 .... 27.93 35.51 32.00 .... 28.28 .... 32.37 28.64 .... 29.00 .... 20.40† 20.71‡

1260XH 46.71 42.69 43.11 47.13 49.79 35.34 43.52 47.54 50.21 39.86 43.93 32.30 40.26 47.96♥ 44.34 40.66 36.91 48.38♥ 44.74 41.06 37.30 25.52 33.81 37.69 41.46 45.15♥ 34.19 38.07 41.85 45.56♥ 34.57 38.46 42.25 34.94 26.90 38.84 27.25 35.31 42.64♥ 39.23 27.59 35.69 27.93 39.61 36.06 28.27 36.43 28.61 28.95 29.29

1400XH 53.72 49.72 50.13 54.14♥ 56.80 42.43 50.55 54.56♥ 57.23 46.91 50.96 39.47 47.32 54.98♥ 51.38 47.73 44.02 55.40♥ 51.79♥ 48.13 44.42 33.10 41.02 44.82 48.53 52.20♥ 41.41 48.94 45.21 52.61♥ 41.79 45.60 49.34♥ 42.18 34.55 46.00 34.91 42.56 49.74♥ 46.39♥ 35.27 42.94 35.83 46.78♥ 43.32 35.98 43.70♥ 36.34 36.69 37.05

1540XH 60.73 56.74 57.15 61.15♥ 63.81 49.49 57.57 61.58♥ 64.24 53.96 57.99♥ 46.59 54.37 62.00♥ 58.41♥ 54.78 51.11 62.42♥ 58.82♥ 55.19 51.51 40.45 48.17 51.91 55.59♥ 59.23♥ 48.56 52.31 56.00♥ 59.65♥ 48.95 52.71 56.41♥ 49.34 41.94 53.10♥ 42.31 49.73 56.81♥ 53.50♥ 42.68 50.12♥ 43.05 53.90♥ 50.51♥ 43.42 50.89♥ 43.79 44.16 44.52♥

1750XH 71.24 67.26 67.68♥ 71.67♥ 74.32 60.06 68.10♥ 72.09♥ 74.75 64.50 68.52♥ 57.21 64.92 72.52♥ 68.94♥ 65.33♥ 61.70 72.94♥ 69.36♥ 65.75♥ 62.10 51.28 58.82 62.51♥ 66.16♥ 69.77♥ 59.22 62.91♥ 66.57♥ 70.19♥ 59.62 63.32♥ 66.98♥ 60.01♥ 52.82 63.72♥ 53.20 60.41♥ 67.39♥ 64.13♥ 53.58 60.81♥ 53.96 64.53♥ 81.20♥ 54.34♥ 61.60♥ 54.72♥ 55.10♥ 55.48♥

Sprockets

560XH 11.39 .... .... 11.77 14.60 .... .... 12.14 14.99 .... .... .... .... 12.51 .... .... .... 12.87 .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ....

Conveyor Components

507XH .... .... .... .... 11.92 .... .... .... 12.30 .... .... .... .... .... .... .... .... 10.05 .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ....

HT Synchrous Belts

Nominal Center Distance Using DYNA-SYNC Belts

XH Belt Width Table 1.29 1-1/4 125

1.56 1-1/2 150

1.84 1-3/4 175

2.14 2 200

2.72 2-1/2 250

3.36 3 300

4.06 3-1/2 350

4.76 4 400

6.15 5 500

7.50 6 600

Teeth in Mesh factor (T.I.M.) Table Symbol None †

10.32 11.70 13.10 14.41 15.84 17.16 18.62 8 9 10 11 12 13 14 800 900 1000 1100 1200 1300 1400

Shaded area indicates stock belt widths.

No. of Teeth In Mesh In Small Pulley 6 or More 5

FEATURES/BENEFITS PAGE PT10-2

8.89 7 700

Factor 1.00 .80

Table Symbol ‡

PULLEY SPECIFICATIONS PAGES PT10-3

No. of Teeth In Mesh In Small Pulley 4

BELT SPECIFICATIONS PAGES PT10-11

PT10-39

Factor .60

ENGINEERING/TECHNICAL PAGES PT10-14

Engineering

Belt Width Factor 1.00 Belt Width 1 Belt Width Code 100


DYNA-SYNC

SELECTION

XL Basic Horsepower Ratings

HT Synchrous Belts Sprockets Conveyor Components

RPM of Faster Shaft 100 200 300 400 500 600 700 800 900 1000 1100 1160 1200 1300 1400 1500 1600 1700 1750 1800 2000 2200 2400 2600 2800 3000 3200 3400 3500 3600 3800 4000 4200 4400 4600 4800 5000 5500 6000 6500 7000 7500 8000 8500 9000 9500 10000

10XL .637 P.D. .02 .04 .06 .08 .10 .12 .14 .16 .18 .20 .22 .23 .24◊ .26◊ .28◊ .30◊ .33◊ .35◊ .36◊ .37◊ .41◊ .45◊ .49◊ .53◊ .57◊ .61◊ .65◊ .69◊ .72◊ .74◊ .78◊ .82◊ .86◊ .90◊ .94◊ .98◊ 1.02◊ .... .... .... .... .... .... .... .... .... ....

11XL .700 P.D. .02 .04 .07 .09 .11 .13 .15 .17 .20 .22 .25 .26 .27 .29 .31 .34 .36 .38 .39 .40◊ .45◊ .49◊ .54◊ .58◊ .63◊ .67◊ .72◊ .77◊ .79◊ .81◊ .83◊ .90◊ .94◊ .99◊ 1.03◊ 1.07◊ 1.12◊ .... .... .... .... .... .... .... .... .... ....

12XL .764 P.D. .02 .05 .07 .10 .12 .14 .17 .19 .22 .24 .26 .28 .29 .31 .34 .36 .40 .42 .43 .44 .49 .54 .59 .64 .69 .74 .79 .83 .86 .88◊ .93◊ .98◊ 1.03◊ 1.08◊ 1.13◊ 1.18◊ 1.23◊ .... .... .... .... .... .... .... .... .... ....

14XL .891 P.D. .03 .06 .09 .11 .14 .17 .20 .23 .26 .29 .31 .33 .34 .37 .40 .43 .46 .49 .50 .51 .57 .63 .68 .74 .80 .86 .91 .97 1.00 1.03 1.09 1.15 1.20 1.25◊ 1.31◊ 1.37◊ 1.42◊ .... .... .... .... .... .... .... .... .... ....

HP for a 1" Wide Belt for Various Pulleys 15XL 16XL 18XL 20XL 21XL .955 1.019 1.146 1.273 1.337 P.D. P.D. P.D. P.D. P.D. .03 .03 .04 .04 .04 .06 .07 .07 .08 .08 .09 .10 .11 .12 .13 .12 .13 .14 .16 .17 .15 .16 .18 .20 .21 .18 .19 .22 .24 .26 .21 .23 .26 .28 .30 .24 .26 .30 .33 .34 .27 .30 .33 .37 .39 .31 .33 .37 .41 .43 .34 .36 .40 .45 .47 .36 .38 .42 .46 .50 .37 .39 .44 .49 .52 .40 .42 .48 .53 .56 .43 .46 .52 .57 .60 .46 .49 .55 .61 .64 .49 .53 .59 .65 .69 .52 .56 .63 .67 .73 .53 .58 .64 .72 .75 .55 .59 .66 .74 .77 .62 .65 .74 .82 .86 .68 .72 .81 .90 .94 .74 .79 .88 .98 1.03 .80 .85 .96 1.06 1.12 .86 .92 1.03 1.15 1.20 .92 .98 1.10 1.23 1.28 .98 1.05 1.18 1.30 1.37 1.04 1.11 1.25 1.38 1.45 1.07 1.15 1.28 1.42 1.49 1.10 1.18 1.32 1.46 1.54 1.17 1.24 1.39 1.54 1.62 1.23 1.30 1.46 1.63 1.71 1.28 1.37 1.53 1.71 1.76 1.34 1.43 1.61 1.78 1.86 1.40 1.50 1.68 1.66 1.95 1.46 1.56 1.75 1.94 2.03 1.52 1.63 1.82 2.01 2.11 1.67◊ 1.78 2.00 2.20 2.30 1.82◊ 1.94 2.16 2.39 2.50 1.96◊ 2.09 2.34 2.57 2.69 2.11◊ 2.24◊ 2.50 2.75 2.87 2.25◊ 2.39◊ 2.66 2.92 3.05 3.10 3.23 .... .... 2.82◊ .... .... 2.97◊ 3.26 3.39 .... .... 3.13◊ 3.41◊ 3.55 .... .... 3.28◊ 3.56◊ 3.70 .... .... 3.41◊ 3.71◊ 3.84

22XL 1.401 P.D. .04 .09 .13 .17 .22 .27 .31 .36 .40 .45 .49 .52 .54 .58 .63 .67 .72 .77 .79 .81 .90 .99 1.07 1.17 1.26 1.34 1.43 1.52 1.57 1.61 1.70 1.78 1.86 1.95 2.04 2.13 2.20 2.41 2.61 2.80 2.99 3.18 3.34 3.52 3.68 3.83 3.97

24XL 1.528 P.D. .05 .10 .14 .19 .24 .29 .34 .40 .44 .49 .54 .56 .59 .64 .69 .74 .79 .83 .86 .88 .98 1.08 1.18 1.25 1.37 1.46 1.56 1.66 1.71 1.75 1.84 1.94 2.03 2.12 2.21 2.30 2.39 2.61 2.82 3.03 3.23 3.41 3.59 3.76 3.92 4.07 4.21

28XL 1.783 P.D. .06 .11 .17 .23 .29 .34 .40 .48 .51 .57 .63 .66 .68 .74 .80 .86 .91 .97 1.00 1.03 1.15 1.25 1.37 1.48 1.59 1.71 1.81 1.92 1.98 2.03 2.13 2.24 2.35 2.45 2.55 2.65 2.75 2.99 3.23 3.42 3.65 3.84 4.02 4.19 4.34 4.47 4.59

30XL 1.910 P.D. .06 .12 .18 .24 .30 .37 .43 .49 .55 .62 .68 .71 .74 .80 .86 .92 .98 1.04 1.07 1.10 1.23 1.34 1.46 1.58 1.71 1.82 1.94 2.05 2.11 2.16 2.27 2.39 2.50 2.61 2.71 2.82 2.92 3.18 3.41 3.64 3.84 4.03 4.21 4.37 4.51 4.63 4.72

XL Belt Width Table Belt Width Factor Belt Width Belt Width Code

.15 1/4 025

.28 3/8 037

.35 7/16 043

.42 1/2 050

.57 5/8 062

.71 3/4 075

.86 7/8 087

1.00 1 100

1.29 1-1/4 125

1.56 1-1/2 150

Shaded area indicates stock belt widths. Engineering

◊Pulley diameter is below recommended minimum. A reduction in belt life should be expected. Suggest alternate drive, when ever possible.

FEATURES/BENEFITS PAGE PT10-2

PULLEY SPECIFICATIONS PAGES PT10-3

BELT SPECIFICATIONS PAGES PT10-11

PT10-40

ENGINEERING/TECHNICAL PAGES PT10-44


12L 1.432 P.D. .06 .13 .19 .25 .31 .37 .44 .50 .54 .56 .62 .69 .72 .75◊ .81◊ .87◊ .94◊ 1.00◊ 1.06◊ 1.09◊ 1.12◊ 1.18◊ 1.24◊ 1.36◊ 1.49◊ 1.55◊ 1.61◊ 1.73◊ 1.85◊ .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ....

13LΔ 1552 P.D. .07 .14 .20 .27 .34 .41 .47 .54 .59 .61 .88 .75 .79 .81 .68 .95 1.02◊ 1.08◊ 1.15◊ 1.17◊ 1.21◊ 1.27◊ 1.35◊ 1.48◊ 1.61◊ 1.68◊ 1.74◊ 1.87◊ 2.00◊ 2.13◊ 2.26◊ 2.32◊ .... .... .... .... .... .... .... .... .... .... .... .... ....

14L 1.671 P.D. .07 .15 .22 .29 .37 .44 .51 .58 .63 .66 .73 .80 .85 .88 .95 1.02 1.09 1.16 1.23 1.27 1.30◊ 1.38◊ 1.45◊ 1.59◊ 1.73◊ 1.80◊ 1.87◊ 2.01◊ 2.15◊ 2.28◊ 2.42◊ 2.49◊ 2.55◊ 2.69◊ 2.83◊ .... .... .... .... .... .... .... .... .... ....

15LΔ 1.790 P.D. .08 .16 .23 .31 .39 .47 .55 .62 .68 .70 .78 .86 .91 .94 1.01 1.09 1.16 1.24 1.32 1.36 1.39 1.47 1.55 1.70 1.85 1.92◊ 2.00◊ 2.14◊ 2.29◊ 2.44◊ 2.58◊ 2.65◊ 2.73◊ 2.86◊ 3.00◊ 3.15◊ 3.28◊ 3.41◊ 3.54◊ 3.67◊ 3.81◊ 3.93◊ 4.05◊ 4.17◊ 4.29◊

16L 1.910 P.D. .08 .17 .25 .33 .42 .50 .58 .67 .73 .75 .83 .92 .97 1.00 1.08 1.16 1.24 1.32 1.41 1.45 1.49 1.57 1.65 1.81 1.97 2.05 2.13 2.29 2.44 2.60 2.75 2.83 2.90◊ 3.03◊ 3.20◊ 3.34◊ 3.49◊ 3.63◊ 3.77◊ 3.91◊ 4.03◊ 4.17◊ 4.29◊ 4.42◊ 4.55◊

HP for a 1" Wide Belt for Various Pulleys 17L 18L 19L 20L 21L 22L 24L 2.029 2.149 2.268 2.387 2.507 2.626 2.865 P.D. P.D. P.D. P.D. P.D. P.D. P.D. .09 .09 .10 .10 .11 .12 .13 .18 .19 .20 .21 .22 .23 .25 .27 .28 .30 .31 .33 .34 .38 .35 .38 .40 .42 .44 .46 .50 .44 .47 .50 .52 .55 .57 .63 .53 .56 .59 .63 .66 .69 .75 .62 .66 .69 .73 .77 .80 .87 .71 .75 .79 .83 .87 .92 1.00 .77 .82 .86 .91 .95 1.00 1.08 .80 .84 .89 .94 .98 1.03 1.12 .89 .94 .99 1.04 1.09 1.14 1.24 .97 1.03 1.08 1.14 1.20 1.25 1.36 1.03 1.08 1.14 1.20 1.26 1.32 1.44 1.06 1.12 1.18 1.24 1.30 1.36 1.49 1.15 1.21 1.28 1.34 1.41 1.48 1.61 1.23 1.30 1.38 1.45 1.52 1.59 1.73 1.32 1.40 1.47 1.55 1.62 1.70 1.85 1.41 1.49 1.57 1.65 1.73 1.81 1.97 1.49 1.58 1.66 1.75 1.83 1.92 2.09 1.54 1.62 1.71 1.80 1.89 1.98 2.15 1.58 1.67 1.76 1.85 1.94 2.03 2.21 1.66 1.76 1.85 1.95 2.04 2.14 2.32 1.75 1.85 1.95 2.05 2.15 2.25 2.44 1.92 2.03 2.14 2.25 2.35 2.46 2.67 2.09 2.21 2.32 2.44 2.56 2.67 2.90 2.17 2.30 2.42 2.54 2.66 2.78 3.01 2.26 2.38 2.51 2.63 2.76 2.88 3.12 2.42 2.56 2.69 2.82 2.96 3.09 3.34 2.59 2.73 2.87 3.01 3.15 3.29 3.55 2.74 2.90 3.04 3.19 3.34 3.48 3.76 2.91 3.07 3.22 3.37 3.53 3.67 3.97 2.99 3.15 3.31 3.46 3.62 3.77 4.06 3.07◊ 3.23 3.39 3.55 3.71 3.86 4.16 3.22◊ 3.40 3.56 3.73 3.89 4.05 4.35 3.37◊ 3.56 3.73 3.89 4.06 4.23 4.54 3.53◊ 3.72 3.88 4.06 4.23 4.40 4.72 3.67◊ 3.86 4.04 4.22 4.40 4.57 4.89 3.82◊ 4.01 4.20 4.38 4.56 4.73 5.05 3.96◊ 4.17 4.35 4.54 4.72 4.89 5.20 4.86 5.04 5.35 4.10◊ 4.31◊ 4.50◊ 4.68 4.23◊ 4.45◊ 4.63◊ 4.82 5.01 5.18 5.48 4.37◊ 4.59◊ 4.77◊ 4.96 5.14 5.31 5.61 4.50◊ 4.72◊ 4.91◊ 5.09 5.28 5.44 5.73 4.62◊ 4.84◊ 5.04◊ 5.22 5.40 5.57 5.84 4.75◊ 4.97◊ 5.15◊ 5.34 5.52 5.68 5.93

26L 3.104 P.D. .14 .27 .41 .54 .68 .81 .95 1.08 1.17 1.21 1.34 1.48 1.56 1.61 1.74 1.87 2.00 2.13 2.26 2.32 2.38 2.51 2.63 2.88 3.12 3.24 3.36 3.59 3.81 4.03 4.24 4.35 4.45 4.64 4.83 5.01 5.19 5.34 5.48 5.63 5.76 5.88 5.98 6.07 6.15

28L 3.342 P.D. .15 .29 .44 .58 .73 .87 1.02 1.16 1.26 1.30 1.45 1.59 1.67 1.73 1.87 2.01 2.15 2.28 2.42 2.49 2.56 2.69 2.82 3.08 3.34 3.47 3.59 3.83 4.06 4.29 4.50 4.61 4.72 4.91 5.10 5.28 5.44 5.59 5.73 5.86 5.98 6.07 6.16 6.23 6.28

30L 3.581 P.D. .16 .31 .47 .62 .78 .94 1.09 1.24 1.35 1.40 1.55 1.70 1.79 1.85 2.00 2.15 2.30 2.44 2.59 2.66 2.73 2.87 3.01 3.28 3.56 3.68 3.81 4.06 4.30 4.54 4.76 4.86 4.97 5.16 5.34 5.52 5.68 5.82 5.94 6.06 6.15 6.23 6.28 6.32 6.35

32L 3.820 P.D. .17 .33 .50 .67 .83 1.00 1.16 1.32 1.44 1.49 1.65 1.81 1.91 1.97 2.13 2.29 2.44 2.60 2.75 2.83 2.90 3.05 3.19 3.49 3.76 3.90 4.03 4.29 4.54 4.77 4.99 5.10 5.21 5.40 5.57 5.74 5.88 6.01 6.12 6.20 6.27 6.32 6.34 6.34 6.33

40L 4.775 P.D. .21 .42 .63 .83 1.04 1.24 1.45 1.85 1.79 1.65 2.05 2.25 2.36 2.44 2.63 2.82 3.01 3.20 3.38 3.47 3.55 3.73 3.89 4.23 4.54 4.69 4.83 5.10 5.35 5.57 5.78 5.87 5.95 6.09 6.21 6.28 6.33 6.35 6.32 6.26 6.16† 6.01† 5.83† 5.60† 5.32†

48L 5.730 P.D. .25 .50 .75 1.00 1.24 1.49 1.73 1.97 2.14 2.21 2.44 2.67 2.81 2.90 3.12 3.34 3.55 3.76 3.97 4.06 4.16 4.35 4.54 4.89 5.21 5.35 5.48 5.73 5.94 6.11 6.23 6.27 6.31 6.33 6.31 6.23 6.09† 5.89† 5.63† 5.30† 4.91† 4.44† 3.89† 3.27† 2.57†

L Belt Width Table Belt Width Factor Belt Width Belt Width Code

.28 3/8 037

.35 7/16 043

.45 1/2 050

.57 5/8 062

.71 3/4 075

.86 7/8 087

1.00 1 100

1.29 1-1/4 125

1.56 1-1/2 150

1.84 1-3/4 175

2.14 2 200

2.72 2-1/2 250

3.36 3 300

FEATURES/BENEFITS PAGE PT10-2

Engineering

Shaded area indicates stock belt widths. Δ Special non-stock sizes. † Belt Speed exceeds 6500 FPM – consult Dodge. ◊Pulley diameter is below recommended minimum. A reduction in belt life should be expected. Suggest alternate drive, when ever possible.

Sprockets

RPM of 10L Faster 1.194 Shaft P.D. 100 .05◊ 200 .10◊ 300 .16◊ 400 .21◊ 500 .26◊ 600 .31◊ 700 .37◊ 800 .42◊ 870 .45◊ 900 .47◊ 1000 .52◊ 1100 .57◊ 1160 .60◊ 1200 .63◊ 1300 .68◊ 1400 .73◊ 1500 .78◊ 1600 .83◊ 1700 .89◊ 1750 .91◊ 1800 .... 1900 .... 2000 .... 2200 .... 2400 .... 2500 .... 2600 .... 2800 .... 3000 .... 3200 .... 3400 .... 3500 .... 3600 .... 3800 .... 4000 .... 4200 .... 4400 .... 4600 .... 4800 .... 5000 .... 5200 .... 5400 .... 5600 .... 5800 .... 6000 ....

Conveyor Components

L Basic Horsepower Ratings

HT Synchrous Belts

DYNA-SYNC

SELECTION

PULLEY SPECIFICATIONS PAGES PT10-3

BELT SPECIFICATIONS PAGES PT10-11

PT10-41

ENGINEERING/TECHNICAL PAGES PT10-14


DYNA-SYNC

SELECTION

H Basic Horsepower Ratings

HT Synchrous Belts Sprockets Conveyor Components

RPM of Faster Shaft 100 200 300 400 500 600 700 800 870 900 1000 1100 1160 1200 1300 1400 1500 1600 1700 1750 1800 1900 2000 2100 2200 2300 2400 2500 2600 2800 3000 3200 3400 3500 3600 3800 4000 4200 4400 4600 4800 5000 5200 5400 5600 5800 6000

14H 2.228 P.D. .25 .50 .74 .99 1.24 1.49 1.73 1.98 2.15 2.23◊ 2.47◊ 2.72◊ 2.86◊ .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ....

16H 2.546 P.D. .28 .57 .85 1.13 1.41 1.70 1.98 2.26 2.46 2.54 2.82 3.10 3.27 3.38◊ 3.66◊ 3.94◊ 4.22◊ 4.50◊ 4.77◊ 4.91◊ 5.05◊ 5.42◊ 5.60 .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ....

17H 2.706 P.D. .30 .60 .90 1.20 1.50 1.80 2.10 2.40 2.61 2.70 3.00 3.30 3.47 3.59 3.89 4.19 4.48◊ 4.78◊ 5.07◊ 5.22◊ 5.36◊ 5.66◊ 5.95◊ .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ....

18H 2.865 P.D. .32 .64 .96 1.27 1.59 1.91 2.23 2.54 2.76 2.86 3.17 3.49 3.68 3.80 4.12 4.43 4.74 5.05 5.36 5.52 5.67◊ 5.98◊ 6.28◊ 6.59◊ 6.89◊ 7.20◊ 7.50◊ 7.80◊ 8.10◊ 8.69◊ 9.28◊ 9.85◊ 10.43◊ 10.71◊ .... .... .... .... .... .... .... .... .... .... .... .... ....

19H 3.024 P.D. .34 .67 1.01 1.34 1.68 2.02 2.35 2.68 2.91 3.01 3.35 3.68 3.88 4.01 4.34 4.67 5.00 5.33 5.65 5.81 5.98 6.30 6.62 6.94 7.26 7.58 7.90 8.21◊ 8.52◊ 9.14◊ 9.75◊ 10.36◊ 10.95◊ 11.24◊ .... .... .... .... .... .... .... .... .... .... .... .... ....

.71 3/4 075

.86 7/8 087

20H 3.183 P.D. .35 .71 1.06 1.41 1.77 2.12 2.47 2.82 3.07 3.17 3.52 3.87 4.08 4.22 4.57 4.91 5.26 5.60 5.94 6.11 6.28 6.62 6.96 7.29 7.63 7.96 8.29 8.62 8.95 9.59 10.23 10.85 11.47 11.77 12.07◊ 12.67◊ 13.24◊ 13.81◊ 14.36◊ 14.90◊ 15.42◊ 15.93◊ 16.41◊ 18.89◊ 17.34◊ 17.77◊ 18.19◊

HP for a 1" Wide Belt for Various Pulleys 21H 22H 24H 26H 28H 3.342 3.501 3.820 4.138 4.456 P.D. P.D. P.D. P.D. P.D. .37 .39 .42 .46 .50 .74 .78 .85 .92 .99 1.11 1.17 1.27 1.38 1.49 1.49 1.56 1.70 1.84 1.98 1.86 1.94 2.12 2.30 2.47 2.23 2.33 2.54 2.75 2.96 2.59 2.72 2.96 3.21 3.45 2.96 3.10 3.38 3.66 3.94 3.22 3.37 3.68 3.98 4.28 3.33 3.49 3.80 4.11 4.43 3.70 3.87 4.22 4.57 4.91 4.06 4.26 4.64 5.02 5.40 4.28 4.48 4.89 5.28 5.68 4.43 4.64 5.05 5.46 5.88 4.79 5.01 5.46 5.91 6.35 5.15 5.39 5.87 6.35 6.83 5.51 5.77 6.28 6.79 7.30 5.87 6.15 6.69 7.23 7.77 6.23 6.52 7.10 7.67 8.23 6.41 6.71 7.30 7.88 8.46 6.59 6.89 7.50 8.10 8.69 6.94 7.26 7.90 8.53 9.15 7.30 7.63 8.29 8.95 9.60 7.65 8.00 8.69 9.37 10.05 8.00 8.36 9.08 9.79 10.49 8.34 8.72 9.47 10.21 10.93 8.69 9.08 9.85 10.62 11.37 9.03 9.44 10.23 11.02 11.80 9.37 9.79 10.61 11.42 12.22 10.04 10.49 11.35 12.21 13.05 10.70 11.18 12.08 12.98 13.85 11.35 11.85 12.79 13.72 14.63 11.99 12.51 13.48 14.45 15.37 12.31 12.84 13.82 14.80 15.74 12.62 13.16 14.16 15.15 16.09 13.23 13.79 14.81 15.82 16.78 13.82 14.40 15.44 16.46 17.43 14.41 15.00 16.04 17.08 18.05 14.97 15.57 16.63 17.67 18.82 15.52◊ 16.13 17.18 18.22 19.16 16.05◊ 16.67 17.71 18.74 19.66 16.56◊ 17.19 18.22 19.23 20.12 17.05◊ 17.69 18.69 19.68 20.53 17.53◊ 18.16◊ 19.13 20.09 20.90 17.98◊ 18.61◊ 19.55 20.47 21.22† 18.41◊ 19.04◊ 19.93 20.80 21.49† 18.82◊ 19.41◊ 20.27 21.10† 21.70†

1.00 1 100

1.29 1-1/4 125

30H 4.775 P.D. .53 1.06 1.59 2.12 2.65 3.17 3.70 4.22 4.58 4.74 5.26 5.77 6.08 6.29 6.79 7.30 7.80 8.30 8.79 9.03 9.28 9.76 10.24 10.71 11.18 11.64 12.09 12.54 12.98 13.84 14.67 15.46 16.22 16.59 16.95 17.63 18.27 18.87 18.42 19.90 20.37 20.77 21.11† 21.39† 21.62† 21.78† 21.88†

32H 5.039 P.D. .57 1.13 1.70 2.26 2.82 3.38 3.94 4.50 4.89 5.05 5.60 6.15 6.48 6.69 7.23 7.77 8.30 8.82 9.34 9.60 9.86 10.36 10.87 11.36 11.85 12.33 12.80 13.27 13.72 14.61 15.46 18.27 17.03 17.40 17.75 18.42 19.04 19.61 20.12 20.57 20.96 21.29† 21.54† 21.73† 21.85† 21.89† 21.85†

36HΔ 5.730 P.D. .64 1.27 1.91 2.54 3.17 3.80 4.43 5.05 5.49 5.67 6.29 6.90 7.26 7.50 8.10 8.69 9.28 9.86 10.43 10.71 10.99 11.55 12.10 12.63 13.16 13.68 14.18 14.68 15.16 16.09 16.96 17.78 18.53 18.89 19.22 19.85 20.40 20.88 21.27† 21.58† 21.81† 21.95† 21.99† 21.93† 21.76† 21.50† 21.12†

40H 6.366 P.D. .71 1.41 2.12 2.82 3.52 4.22 4.91 5.60 6.08 6.29 6.96 7.63 8.03 8.30 8.95 9.60 10.24 10.87 11.49 11.79 12.09 12.69 13.27 13.84 14.40 14.94 15.46 15.98 16.47 17.41 18.27 19.06 19.76 20.08 20.37 20.89 21.31† 21.62† 21.83† 21.82† 21.89† 21.73† 21.44† 21.02† 20.45† 19.75† ....

4.76 4 400

6.15 5 500

7.50 6 600

44HΔ 7.003 P.D. .78 1.56 2.33 3.10 3.87 4.64 5.40 6.15 6.67 6.89 7.63 8.36 8.80 9.08 9.79 10.49 11.18 11.85 12.51 12.84 13.15 13.78 14.40 14.99 15.57 16.13 16.66 17.18 17.67 18.60 19.42 20.14 20.75 21.01 21.24† 21.60† 21.83† 21.93† 21.87† 21.67† 21.30† 20.77† 20.06† .... .... .... ....

48H 7.639 P.D. .85 1.70 2.54 3.38 4.22 5.05 5.88 6.69 7.26 7.50 8.30 9.08 9.55 9.86 10.62 11.36 12.09 12.80 13.50 13.84 14.18 14.83 15.46 16.08 16.66 17.23 17.76 18.27 18.75 19.63 20.38 20.99 21.46† 21.63† 21.77† 21.92† 21.90† 21.70† 21.32† 20.73† 19.93† .... .... .... .... .... ....

8.89 7 700

10.32 8 800

H Belt Width Table Belt Width Factor Belt Width Belt Width Code

.42 1/2 050

.57 5/8 062

1.56 1-1/2 150

1.84 1-3/4 175

2.14 2 200

2.72 2-1/2 250

3.36 3 300

4.06 3-1/2 350

Engineering

Shaded area indicates stock belt widths. Δ Special non-stock sizes. † Belt Speed exceeds 6500 FPM – consult Dodge. ◊Pulley diameter is below recommended minimum. A reduction in belt life should be expected. Suggest alternate drive, when ever possible.

FEATURES/BENEFITS PAGE PT10-2

PULLEY SPECIFICATIONS PAGES PT10-3

BELT SPECIFICATIONS PAGES PT10-11

PT10-42

ENGINEERING/TECHNICAL PAGES PT10-44


32 XH 8.913 P.D. 1.34 2.69 4.03 5.36 6.40 6.71 6.80 7.56 7.95 8.96 9.21 10.44 11.29 11.64 12.80 13.92 14.57 14.99 16.01 16.98 17.89 18.82 19.51 19.87 20.22 20.86 21.42 21.88 22.27 22.55 22.75 22.84 22.82 22.47† 21.65† 20.33† 18.48† .... .... .... .... .... ....

HP for a 1” Wide Belt for Various Pulleys RPM 40 18 20 22 24 26 30 32 of XH XXH XXH XXH XXH XXH XXH XXH Faster 11.141 7.162 7.958 8.753 9.549 10.345 11.937 13.528 Shaft P.D. P.D. P.D. P.D. P.D. P.D. P.D. P.D. 1.68 100 1.33◊ 1.48 1.83 1.77 1.92 2.21 2.51 3.37 200 2.66◊ 2.95 3.24 3.54 3.84 4.42 5.00 5.02 300 3.98◊ 4.42 4.85 5.29 5.72 6.58 7.45 6.66 400 5.29◊ 5.87 8.44 7.02 7.60 8.73 9.85 8.39 9.06 10.40 11.71 7.70 7.02 7.95 480 6.33◊ 8.26 500 6.63◊ 7.31◊ 8.02 8.73 9.43 10.81 12.17 8.42 510 6.72◊ 7.45◊ 8.17 8.89 9.61 11.02 12.39 9.36 570 7.50◊ 8.31◊ 9.11 9.90 10.68 12.23 13.73 9.82 600 7.88◊ 8.73◊ 9.57 10.40 11.22 12.83 14.39 11.04 680 8.89◊ 9.85◊ 10.78 11.71 12.62 14.39 16.09 11.35 700 9.15◊ 10.13◊ 11.09 12.03 12.96 14.77 16.51 12.80 800 10.40◊ 11.49◊ 12.56 13.62 14.64 16.62 18.49 13.79 870 10.85◊ 12.43◊ 13.56 14.70 15.79 17.88 19.78 14.18 900 11.69◊ 12.83◊ 14.00◊ 15.15 16.23 18.37 20.31 15.51 1000 12.83◊ 14.14◊ 15.40◊ 16.62 17.80 20.01 21.98 16.74 1100 14.00◊ 15.40◊ 16.94◊ 18.00 19.26 21.50 23.45 17.44 1160 14.70◊ 16.14◊ 17.52◊ 18.84 20.01 22.34 24.23 17.89 1200 .... 16.62◊ 18.03◊ 19.37◊ 20.62 22.88 24.71 18.94 1300 .... 17.80◊ 19.26◊ 19.88◊ 21.88 24.07 26.75 19.87 1400 .... 18.93◊ 20.41◊ 21.79◊ 23.03 26.10 26.54 20.71 1500 .... 19.19◊ 21.50◊ 22.88◊ 24.07 26.95 27.06 21.42 1600 .... 21.02◊ 22.52◊ 23.84◊ 24.98 26.62 27.32 21.99 1700 .... 21.99◊ 23.45◊ 24.71◊ 25.75 27.07 27.27 22.22 1750 .... 22.43◊ 23.88◊ 25.11◊ 26.08 27.22 27.12 22.35 1800 .... 22.87◊ 24.29◊ 26.47◊ 26.38◊ 27.31 26.89 22.70 1900 .... 23.69◊ 25.04◊ 26.11◊ 26.86◊ 27.31 26.18† 22.84 2000 .... 24.44◊ 25.70◊ 26.62◊ 27.18◊ 27.08 26.11† 22.81 2100 .... 25.11◊ 26.24◊ 27.00◊ 27.33◊ 26.56† 23.66† 22.61 2200 .... 25.70◊ 26.69◊ 27.24◊ 27.31◊ 26.79† .... .... 22.30† 2300 .... 26.21◊ 27.03◊ 27.33◊ 27.09◊ 24.74† 21.65† 2400 .... 26.62◊ 27.24◊ 27.28◊ 26.69† 23.36† .... 20.89† 2500 .... 29.95◊ 27.33◊ 27.06◊ 26.07† .... .... 19.92† 2600 .... 27.18◊ 27.30◊ 26.69† 25.25† .... .... .... 2800 .... 27.34◊ 26.83◊ 25.40† 22.95† .... .... .... 3000 .... 27.07◊ 26.79 23.36† .... .... .... .... 3200 .... .... .... .... .... .... .... .... 3400 .... .... .... .... .... .... .... .... 3500 .... .... .... .... .... .... .... .... 3600 .... .... .... .... .... .... .... .... 3800 .... .... .... .... .... .... .... .... 4000 .... .... .... .... .... .... .... .... 4200 .... .... .... .... .... .... .... .... 4400 .... .... .... .... .... .... ....

40 XXH 15.915 P.D. 2.95 5.87 8.73 11.49 13.61 14.13 14.39 15.89 16.62 18.49 18.93 21.02 22.34 22.86 24.44 25.70 26.29 26.62 27.18 27.33 27.05 26.33† 25.11† 24.31† 23.36† .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ....

XH, XXH Belt Width Table Belt Width Factor Belt Width Belt Width Code

1.00 1 100

1.29 1-1/4 125

1.56 1-1/2 150

1.84 1-3/4 175

2.14 2 200

2.72 2-1/2 250

3.36 3 300

4.06 3-1/2 350

4.76 4 400

6.15 5Δ 500

7.50 6 600

8.89 7 700

10.32 11.70 13.10 14.41 15.84 17.16 18.62 8 9 10 11 12 13 14 800 900 1000 1100 1200 1300 1400

Engineering

Shaded area indicates stock belt widths. † Belt Speed exceeds 6500 FPM – consult Dodge. ◊Pulley diameter is below recommended minimum. A reduction in belt life should be expected. Suggest alternate drive, when ever possible. Δ Stock with XXH Series only.

FEATURES/BENEFITS PAGE PT10-2

HT Synchrous Belts

20 XH 5.570 P.D. 0.84 1.68 2.52 3.37 4.03 4.20◊ 4.29◊ 4.77◊ 5.02◊ 5.68◊ 5.84◊ 6.66◊ 7.23◊ 7.46◊ 8.26◊ 9.05◊ 9.51◊ 9.83◊ 10.59◊ 11.35◊ 12.08◊ 12.80◊ 13.50◊ 13.85◊ .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ....

Ratings

HP for a 1” Wide Belt for Various Pulleys 22 24 26 28 30 XH XH XH XH XH 6.127 6.685 7.241 7.799 8.356 P.D. P.D. P.D. P.D. P.D. 0.93 1.01 1.11 1.18 1.26 1.85 2.02 2.19 2.36 2.52 2.78 3.03 3.28 3.54 3.78 3.70 4.03 4.37 4.70 5.02 4.43 4.82 5.22 5.62 6.00 4.61 5.02 5.44 5.85 6.26 4.71 5.12 5.54 5.97 6.37 5.25 5.72 6.17 6.65 7.10 5.52 6.00 6.50 6.98 7.47 6.24 6.80 7.34 7.88 8.42 6.42 6.98 7.54 8.10 8.66 7.31 7.95 8.59 9.21 9.83 7.92 8.61 9.29 9.97 10.63 8.19◊ 8.90 9.59 10.29 10.97 9.05◊ 9.82 10.59 11.35 12.08 9.91◊ 10.75 11.56 12.38 13.15 10.41◊ 11.29 12.13 12.97 13.79 10.75◊ 11.64◊ 12.51 13.37 14.29 11.57◊ 12.51◊ 13.44 14.32 15.18 12.37◊ 13.37◊ 14.32 15.25 16.14 13.15◊ 14.19◊ 15.18 16.14 17.03 13.92◊ 14.99◊ 16.01 16.98 17.14 14.66◊ 15.76◊ 16.80 17.78 18.68 15.03◊ 16.14◊ 17.17 18.16 19.06 15.37◊ 16.51◊ 17.56◊ 18.53 19.42 16.07◊ 17.22◊ 18.65◊ 19.23 20.69 16.74◊ 17.89◊ 18.94◊ 19.87 20.71 17.39◊ 18.53◊ 19.56◊ 20.48 21.25 18.00◊ 19.43◊ 20.14◊ 21.01 21.72 18.58◊ 19.70◊ 20.67◊ 21.47 22.11 19.13◊ 20.22◊ 21.14◊ 21.88 22.42 .... 20.71◊ 21.57◊ 22.22◊ 22.64 .... 21.14◊ 21.94◊ 22.49◊ 22.80 .... 21.89◊ 22.49◊ 22.81◊ 22.81 .... 22.42◊ 22.80◊ 22.81◊ 22.44† .... 22.75◊ 22.82◊ 22.47†◊ 21.65† .... 22.84◊ 22.58◊ 21.78†◊ 20.42† .... 22.81◊ 22.34†◊ 21.29†◊ 19.64† .... 22.71◊ 22.02†◊ 20.72†◊ 18.73† .... 22.31†◊ 21.41†◊ 19.22†◊ .... .... .... .... 21.65†◊ 19.92†◊ .... 20.71†◊ 18.33†◊ .... .... .... 19.47†◊ .... .... ....

Sprockets

Ratings

Conveyor Components

XXH Basic Horsepower

XH Basic Horsepower RPM 18 of XH Faster 5.013 Shaft P.D. 100 0.76◊ 200 1.51◊ 300 2.28◊ 400 3.03◊ 480 3.63◊ 500 3.78◊ 510 3.86◊ 570 4.30◊ 600 4.53◊ 680 5.12◊ 700 5.27◊ 800 6.00◊ 870 6.52◊ 900 6.74◊ 1000 7.47◊ 1100 8.19◊ 1160 8.61◊ 1200 .... 1300 .... 1400 .... 1500 .... 1600 .... 1700 .... 1750 .... 1800 .... 1900 .... 2000 .... 2100 .... 2200 .... 2300 .... 2400 .... 2500 .... 2600 .... 2800 .... 3000 .... 3200 .... 3400 .... 3500 .... 3600 .... 3800 .... 4000 .... 4200 .... 4400 ....

DYNA-SYNC

SELECTION

PULLEY SPECIFICATIONS PAGES PT10-3

BELT SPECIFICATIONS PAGES PT10-11

PT10-43

ENGINEERING/TECHNICAL PAGES PT10-14


DYNA-SYNC

ENGINEERING/TECHNICAL Dimensions, Tolerances, etc. Warning–Do not use DYNA-SYNC Pulleys with belt speeds exceeding 6500 fpm. May cause pulleys to fragment resulting in personal injury or property damage.

Concentricity and Face Run-Out Tolerances Runout (T.I.R.◊)

O.D.

Standard Keyways

HT Synchrous Belts

Bore Range 5/16 - 7/16 Incl. Over 7/16 - 9/16 Incl. Over 9/16 - 7/8 Incl. Over 7/8 - 1-1/4 Inc. Over 1-1/4 - 1-3/8 Inc. Over 1-3/8 - 1-3/4 Incl. Over 1-3/4 - 2-1/4 Inc. Over 2-1/4 - 2-3/4 Incl. Over 2-3/4 - 3-1/4 Incl.

Tol.

8” & under .005” Radial For each add'l. inch of O.D. add .0005” 1” & Under .001” Axial For each add'l. inch of O.D. thru 10” add .001” For each add'l. inch of O.D. over 10” add .0005” ◊ Total Indicator Reading

Reborable Pulley Bore Tolerances Bore Size 15/16” & Under 1” to 1-15/16” 2” to 2-15/16” 3” & Over

Tol. .0010” - .0000” .0015” - .0000” .0020” - .0000” .0025” - .0000”

Keyway 3/32 x 3/64 1/8 x 1/16 3/16 x 3/32 1/4 x 1/8 5/16 x 5/32 3/8 x 3/16 1/2 x 1/4 5/8 x 5/16 3/4 x 3/8

Pulley Outside Diameter/Diameter Over Belt

Sprockets

Pulley O.D. P.D.- 0.02" P.D.- 0.03" P.D.- 0.054" P.D.- 0.11" P.D.- 0.12"

Pitch XL L H XH XXH

Rebore Charges–Reborable pulley alteration charges are shown in MLP Price Book. TAPER-LOCK pulleys accommodate all common tolerance variations found in commercial shafting. Balancing–All DYNA-SYNC Pulleys have been given a careful static balance for operation up to 6500 FPM. When vibration is a problem, dynamic balancing is recommended – Consult price book MLP. (See Warning above)

Conveyor Components

Special Pulleys–In 1/5 thru 1-1/4” pitches, pulleys can be made to suit customer's specifications and may be furnished in sizes not listed on previous pages. Send us your inquiry.

NOMENCLATURE Pulleys TL Bush. System

30 No. of Teeth

3/8” pitch (L)

H Pitch Code

150 Belt Width (x100) = 1.5”

Belts 900 Belt Lgth. (x10) = 90.0”

1/5” pitch (XL)

Diameter Over Belt P.D.+0.08" P.D.+0.11" P.D.+0.11" P.D.+0.27" ......

1/2” pitch (H)

7/8” pitch (XH)

H Pitch Code

300 Belt Width (x100) - 3.0”

1-1/4” pitch (XXH)

Typical uses are shown below the Tooth Dimensions Sketches . . .

Engineering

Business machines, instrumentation, sound equipment.

FEATURES/BENEFITS PAGE PT10-2

FHP applications such as Machine tools, pumps, home appliances, small fans, presses, motortools, pumps, blowers. generator sets.

PULLE SPECIFICATIONS PAGES PT10-

Medium-torque applications – such as heavy industrial equipment.

BELT SPECIFICATIONS PAGES PT10-11

PT10-44

High-torque abolitions – such as heavy industrial equipment.

SELECTION PAGES PT10-14


DYNA-SYNC

ENGINEERING/TECHNICAL Installing / Tensioning DYNA-SYNC Drives Alignment

TENSIONING THE DRIVE – Simple Tensioning Procedure: Step 1 – Calculate the value of the deflection force "f" from the following formula, referring to drawing below. T + (S/L) K Force of Deflection f = 16 Where S = Span distance in inches T = Tension in Lbs. from Table below K = Constant from Table L = Length of Belt

Pulley Flanges At least one pulley must have flanges. If center distance is more than 8 times the diameter of the smallest pulley, both pulleys should be flanged. Vertical shaft drives may require flanges on both pulleys.

Step 2 – Using a straight edge as a reference, apply enough force to deflect belt 1/64" for every inch of center span. If this force is less than the calculated "f", increase center distance of pulleys. If more than "f", decrease center distance of pulleys.

Installation Reduce center distance so that belt can be slipped into place without forcing. Do not pry belt onto pulleys. Increase center distance to tighten belt. Belt should be snug, but not excessively tight. If belt has a tendency to "jump teeth" during operation, increase belt tension.

HT Synchrous Belts

Use straight edge to check parallel and offset alignment. Align pulleys within 1/4° or 1/16" per foot center distance. Supporting framework must be rigid.

Idlers Sprockets

Adjustable center distance is preferred over idlers to tension belt. Idlers should be positioned on the slack side of the drive. Inside idlers are preferred over outside idlers. Idler diameter should be at least as large as the smallest pulley. Belt Pitch

Values # 1/4 3/8 1/2 T 6.7 10 15 XL 1/5” K .85 1.7 2.7 T ... 11.4 17.1 L 3/8” K ... 8.5 9.9 T ... ... 39.3 H 1/2” K ... ... 17 T ... ... ... XH 7/8” K ... ... ... T ... ... ... XXH 1-1/4” K ... ... ... #T = Tension in Pounds; K = constant for above formula.

5/8 20 3.6 22.1 14 53.3 22 ... ... ... ...

3/4 24.2 4.7 27.9 17 66 32 ... ... ... ...

1 34.2 6.7 39.3 24 93.3 46 ... ... ... ...

Belt Width 1-1/2 2 2-1/2 ... ... ... ... ... ... 61.4 ... ... 37 ... ... 145.3 200 254 71 95 125 ... 227 288 ... 190 250 ... 556 707 ... 310 410

3 ... ... ... ... 313 152 356 305 873 500

4 ... ... ... ... 444 210 504 440 1238 710

5 ... ... ... ... 574 265 652 568 1599 920

Belt Width 2-1/2 ... 150 381 519 636

5 ... ... 861 1175 1439

6 ... ... 1050 1431 1755

8 ... ... ... 1969 2415

6 ... ... ... ... 700 320 795 700 1950 1100

8 ... ... ... ... ... ... 1094 1080 2683 1500

10 ... ... ... ... .... ... 1388 1330 3406

Allowable Working Tension (Ta) Lbs. 1/4 3/8 1/2 5/8 3/4 1 XL 1/5” 8 12 18 24 29 41 L 3/8” ... 16 24 31 39 55 H 1/2” ... ... 59 80 99 140 XH 7/8” ... ... ... ... ... ... XXH 1-1/4” ... ... ... ... ... ... Note: These values have not been corrected for centrifugal force loss.

FEATURES/BENEFITS PAGE PT10-2

1-1/2 ... 86 218 ... ...

2 ... 118 300 409 500

3 ... 185 470 641 786

4 ... ... 666 908 1114

10 ... ... ... 2499 3065

12 ... ... ... 3022 3706

14 .... .... .... 3552 4357

Engineering

Belt Pitch

Conveyor Components

Belt Deflection Force T and K Values

PULLE SPECIFICATIONS PAGES PT10-

BELT SPECIFICATIONS PAGES PT10-11

PT10-45

SELECTION PAGES PT10-14


DYNA-SYNC

NOTES

HT Synchrous Belts Sprockets Conveyor Components Engineering FEATURES/BENEFITS PAGE PT10-2

PULLE SPECIFICATIONS PAGES PT10-

BELT SPECIFICATIONS PAGES PT10-11

PT10-46

SELECTION PAGES PT10-14


HT Synchronous Belt Drives

DYNA-SYNC

CONTENTS

Features/Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT11-2

MPB & BTS Sprockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT11-9 Fin-Fan Sprockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT11-9 QD HTD Sprockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT11-10 HT200 Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT11-17

HT Synchrous Belts

Specification HT TAPER-LOCK Sprockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT11-4

14MM Ratio/Center Distance Tables . . . . . . . . . . . . . . . . . . . . . . PT11-48 20MM Ratio/Center Distance Tables . . . . . . . . . . . . . . . . . . . . . . PT11-60 Engineering/Technical Overhung Load Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT11-64 Installation and Tensioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT11-65 Software: VIA-SYNC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT11-67 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT11-67

Conveyor Components

HT200 Basic HP Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT11-22 HTD/HT100 Basic HP Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . PT11-27 5MM Ratio/Center Distance Tables . . . . . . . . . . . . . . . . . . . . . . . PT11-35 8MM Ratio/Center Distance Tables . . . . . . . . . . . . . . . . . . . . . . . PT11-38

Sprockets

Selection Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT11-19

Part Number Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INDEX-1

Engineering

Keyword Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INDEX-29

PT11-1


DYNA-SYNC

FEATURES/BENEFITS DODGE HT200 Drives High Torque Synchronous Belt Drives • 200% Rating of HTD • Quieter Operation • More Compact

HT Synchrous Belts

• 8MM & 14MM Pitch Plus all the benefits of standard HTD Drives: • Positive, non-slip drive • No lubrication required • Non-stretch • Corrosion resistant • Abrasion resistant • Virtually no backlash

Sprockets

• Clean operation • Long life • Low maintenance

THE TECHNOLOGY OF HT200 PERFORMANCE Advanced Tooth Profile Design • Optimizes distribution of load forces between belt and sprocket. • Improves dynamic efficiency between sprocket and belt. • Increases torque capacity.

Conveyor Components

• Allows more compact, narrower drive. • Operates more quietly. New Belt Construction • Tougher Chloroprene rubber resists tooth shear, increases load capacity. • Strong, stretch-resistant tensile cords. • Tough, wear-resistant nylon tooth facing keeps friction low, protects from wear. HT200: The Next Level • 200% rating at HTD • New Belt Construction

Engineering

• Compact Design • Uses HT TAPER-LOCK Sprockets • Competitvely Priced

PT11-2


HT TAPER-LOCK Sprockets • Torque Rated: Shaft gripping strength to meet the higher demands of the 200% rating of HT200 Belts. • Compatible: Accepts HT200 or standard HTD belts. • Compact: Save shaft space with compact TAPER-LOCK design. • Reduce Overhung Load: Compact design allows closer mounting to motor or reducer bearings. Improves bearing life, reduces maintenance costs.

Caution: Standard QD style HTD sprockets manufactured by DODGE or by others may not have the torque capacity for the higher rated HT200 belts. HT TAPER-LOCK sprockets from DODGE are designed to handle the higher loads.

Upgrade Roller Chain Drives to DODGE HT200

TAPER-LOCK THE Compact Synchronous Drive

TAPER-LOCK HT

FLANGE-BUSHED SPROCKET Compact TAPER-LOCK design takes up less shaft space than narrow width belts or products using flanged style bushing. The result is a more compact, economical synchronous drive.

• Clean: No lubrication required. No messy oil drips or spills. • Quiet: No metal-to-metal contact. • Smooth Operation: No chordal action of chain drive that results in vibration and speed variation. • Economical Drive Guard: Basic enclosed or ventilated guard will suffice. Oil seals, filler and drain plugs not required.

PT11-3

DYNA-SYNC HT Synchrous Belts Sprockets

DODGE QD HTD Sprockets • Rated for capacity of standard HTD belts. • Compatible for standard HTD belts. • Can run HT200 belts at HTD rating. • Use HT200 belts for quieter operation than with HTD belts.

Conveyor Components

DODGE HT200 Drives

Engineering

FEATURES/BENEFITS


DYNA-SYNC

SPECIFICATION HT TAPER-LOCK Sprockets TYPE A

TYPE B

TYPE D E

F M

HT Synchrous Belts

TYPE AF

TYPE BF

The figure following the sketch reference letter in the "Type" column indicates the construction of the sprocket (1 = Solid, 2 = Web, and 3 = Arms), and the letter "F" indicates that the sprocket has flanges.

5MM SPROCKETS SPROCKET NUMBER Sprockets Conveyor Components Engineering

5M-15 P32-5M-15-MPB P34-5M-15-MPB P36-5M-15-MPB P36-5M-15-1108 P38-5M-15-1108 P40-5M-15-1108 P44-5M-15-1108 P48-5M-15-1210 P52-5M-15-1210 P56-5M-15-1610 P60-5M-15-1610 P64-5M-15-1610 P68-5M-15-1610 P72-5M-15-1610 P80-5M-15-1610 P90-5M-15-1610 P112-5M-15-2012 5M-25 P32-5M-25-MPB P34-5M-25-MPB P36-5M-25-1108 P38-5M-25-1108 P40-5M-25-1108 P44-5M-25-1108 P48-5M-25-1210 P52-5M-25-1210 P56-5M-25-1610 P60-5M-25-1610 P64-5M-25-1610 P68-5M-25-2012 P72-5M-25-2012 P80-5M-25-2012 P90-5M-25-2012 P112-5M-25-2012

DIAMETERS

PART NO.

NO. OF TEETH

P.D.

O.D.

112465 112466 114640 112467 112468 112469 112470 112471 112472 112473 112474 112475 112476 112477 112478 112479 112480

32 34 36 36 38 40 44 48 52 56 60 64 68 72 80 90 112

2.005 2.130 2.256 2.256 2.381 2.506 2.757 3.008 3.258 3.509 3.760 4.010 4.261 4.511 5.013 5.639 7.018

1.960 2.085 2.211 2.211 2.336 2.461 2.712 2.963 3.213 3.464 3.715 3.965 4.216 4.466 4.968 5.594 6.973

112481 112482 112483 112484 112485 112486 112487 112488 112489 112490 112491 112492 112493 112494 112495 112496

32 34 36 38 40 44 48 52 56 60 64 68 72 80 90 112

2.005 2.130 2.256 2.381 2.506 2.757 3.008 3.258 3.509 3.760 4.010 4.261 4.511 5.013 5.639 7.018

1.960 2.085 2.211 2.336 2.461 2.712 2.963 3.213 3.464 3.715 3.965 4.216 4.466 4.968 5.594 6.973

FEATURES/BENEFITS PAGES PT11-2

DIMENSIONS (IN.)

FLANGE F = 0.89" 2.125 2.375 2.375 2.375 2.613 2.733 3.090 3.328 3.566 3.805 4.044 4.170 4.520 4.670 ... ... ... F = 1.28" 2.125 2.375 2.375 2.613 2.733 3.090 3.328 3.566 3.805 4.044 4.170 4.520 4.670 ... ... ...

TYPE

Bore Sizes

Approx. Approx. Weight WR^2 (LBS.) (Lb-Ft^2)

E

M

Min.

Max

A1F A1F A1F A1F B1F B1F B1F B1F B1F B1F B1F B1 B1 B1

0.50 0.50 0.50 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0.11 0.11 0.11 0.11 0.11 0.11 0.11 0.11 0.11 0.36

1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2

7/8 1 1-1/8 1-1/8 1-1/8 1-1/8 1-1/8 1-1/4 1-1/4 1-11/16 1-11/16 1-11/16 1-11/16 1-11/16 1-11/16 1-11/16 2-1/8

0.8 0.9 1.1 0.47 0.57 0.68 0.91 1.0 1.3 1.4 1.7 2.1 2.4 2.8 3.7 4.9 8.3

0.0016 0.0021 0.0028 0.0028 0.0036 0.0047 0.0072 0.0105 0.0153 0.0192 0.0267 0.0353 0.0458 0.0583 0.0906 0.1474 0.3750

A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1 A1 A1

0.50 0.50 0 0 0 0 0 0 0 0 0 0.03 0.03 0.03 0.03 0.03

0 0 0.41 0.41 0.41 0.41 0.28 0.28 0.28 0.28 0.28 0.00 0.00 0.00 0.00 0.00

1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2

7/8 1 1-1/8 1-1/8 1-1/8 1-1/8 1-1/4 1-1/4 1-11/16 1-11/16 1-11/16 2-1/8 2-1/8 2-1/8 2-1/8 2-1/8

1.1 1.2 0.65 0.73 0.85 1.1 1.2 1.6 1.6 2.1 2.4 2.7 3.3 4.5 6.2 10.7

0.0024 0.0031 0.0039 0.0048 0.0061 0.0091 0.0130 0.0185 0.0240 0.0335 0.0430 0.0571 0.0751 0.1215 0.2032 0.5102

SPECIFICATIONS: BELTS PAGES PT11-17

SELECTION PAGES PT11-19

PT11-4

ENGINEERING/TECHNICAL PAGES PT11-64


DYNA-SYNC

SPECIFICATION HT TAPER-LOCK Sprockets TYPE A

TYPE B

TYPE C

TYPE D E

F

TYPE CF

The figure following the sketch reference letter in the "Type" column indicates the construction of the sprocket (1 = Solid, 2 = Web, and 3 = Arms), and the letter "F" indicates that the sprocket has flanges.

8MM SPROCKETS PART NO.

NO. OF TEETH

DIAMETERS P.D.

O.D.

DIMENSIONS (IN.)

FLANGE

8M-20 F = 1.13" P22-8M-20-1108* 112850 22 2.206 2.152 2.559 P24-8M-20-1108 112851 24 2.406 2.352 2.756 P26-8M-20-1108 112852 26 2.607 2.553 2.953 P28-8M-20-1108 112853 28 2.807 2.753 3.150 P30-8M-20-1210 112854 30 3.008 2.954 3.346 P32-8M-20-1210 112855 32 3.208 3.154 3.543 P34-8M-20-1610 112856 34 3.409 3.355 3.819 P36-8M-20-1610 112857 36 3.609 3.555 3.937 P38-8M-20-1610 112858 38 3.810 3.756 4.134 P40-8M-20-1610 112859 40 4.010 3.956 4.331 P44-8M-20-2012 112860 44 4.411 4.357 4.764 P48-8M-20-2012 112861 48 4.812 4.758 5.157 P56-8M-20-2012 112862 56 5.614 5.560 5.945 P64-8M-20-2012 112863 64 6.416 6.362 6.772 P72-8M-20-2012 112864 72 7.218 7.164 7.598 P80-8M-20-2517 112865 80 8.020 7.966 8.386 P90-8M-20-2517 112866 90 9.023 8.969 ... 8M-30 F = 1.5" P22-8M-30-1108* 112867 22 2.206 2.152 2.559 P24-8M-30-1108 112868 24 2.406 2.352 2.756 P26-8M-30-1108 112869 26 2.607 2.553 2.953 P28-8M-30-1108 112870 28 2.807 2.753 3.150 P30-8M-30-1210 112871 30 3.008 2.954 3.346 P32-8M-30-1210 112872 32 3.208 3.154 3.543 P34-8M-30-1610 112873 34 3.409 3.355 3.819 P36-8M-30-1610 112874 36 3.609 3.555 3.937 P38-8M-30-1610 112875 38 3.810 3.756 4.134 P40-8M-30-2012 112876 40 4.010 3.956 4.331 44 4.411 4.357 4.764 P44-8M-30-2012 112877 P48-8M-30-2012 112878 48 4.812 4.758 5.157 P56-8M-30-2012 112879 56 5.614 5.560 5.945 P64-8M-30-2517 112880 64 6.416 6.362 6.772 P72-8M-30-2517 112881 72 7.218 7.164 7.598 P80-8M-30-2517 112882 80 8.020 7.966 8.386 P90-8M-30-2517 112883 90 9.023 8.969 ... P112-8M-30-2517 112884 112 11.229 11.175 ... P144-8M-30-2517 112849 114 14.437 14.383 ... TAPER-LOCK sprockets limited to torque capacity of bushing. FEATURES/BENEFITS PAGES PT11-2

TYPE

Bore Sizes

Approx. Approx. Weight WR^2 (LBS.) (Lb-Ft^2)

E

M

Min.

Max

A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F B1F B1F B1F B1F B1F B1F C2

0.00 0.00 0.00 0.26 0.13 0.00 0.13 0.13 0.13 0.13 0.00 0.00 0.00 0.00 0.00 0.00 0.31

0.26 0.26 0.26 0.00 0.00 0.13 0.00 0.00 0.00 0.00 0.12 0.12 0.12 0.12 0.12 0.62 0.31

1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2

1-1/8 1-1/8 1-1/8 1-1/8 1-1/4 1-1/4 1-11/16 1-11/16 1-11/16 1-11/16 2-1/8 2-1/8 2-1/8 2-1/8 2-1/8 2-11/16 2-11/16

0.5 0.7 0.9 1.2 1.2 1.4 1.4 1.7 2.0 2.4 2.7 3.7 5.6 7.7 10 13 12

0.0027 0.0044 0.0065 0.0093 0.0116 0.0157 0.0185 0.0246 0.0320 0.0406 0.0585 0.0916 0.1768 0.3075 0.4991 0.7725 0.9037

A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F B1F B1F B1F C2 C2 D3

0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.13 0.13 0.38

0.63 0.63 0.63 0.63 0.50 0.50 0.50 0.50 0.50 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.13 0.13 0.13

1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2

1-1/8 1-1/8 1-1/8 1-1/8 1-1/4 1-1/4 1-11/16 1-11/16 1-11/16 2-1/8 2-1/8 2-1/8 2-1/8 2-11/16 2-11/16 2-11/16 2-11/16 2-11/16 2-11/16

0.64 0.90 1.1 1.5 1.5 1.7 1.8 2.2 2.5 2.3 3.2 4.2 6.3 9.5 13 16 22 24 31

0.0036 0.0058 0.0082 0.0124 0.0152 0.0199 0.0241 0.0323 0.0409 0.0453 0.0712 0.1069 0.2087 0.4044 0.6599 1.019 1.650 1.764 6.014

SPECIFICATIONS: BELTS PAGES PT11-17

SELECTION PAGES PT11-19

PT11-5

ENGINEERING/TECHNICAL PAGES PT11-64

Sprockets

SPROCKET NUMBER

Conveyor Components

TYPE BF

Engineering

TYPE AF

HT Synchrous Belts

M


DYNA-SYNC

SPECIFICATION HT TAPER-LOCK Sprockets 8MM SPROCKETS SPROCKET NUMBER

HT Synchrous Belts Sprockets

8M-50 P28-8M-50-1108* P30-8M-50-1210 P32-8M-50-1210 P34-8M-50-1610 P36-8M-50-1610 P38-8M-50-1610 P40-8M-50-2012 P44-8M-50-2012 P48-8M-50-2012 P56-8M-50-2517 P64-8M-50-2517 P72-8M-50-2517 P80-8M-50-2517 P90-8M-50-3020 P112-8M-50-3020 P144-8M-50-3020 P192-8M-50-3020 8M-85 P34-8M-85-1615 P36-8M-85-1615 P40-8M-85-2012 P44-8M-85-2012 P48-8M-85-2012 P56-8M-85-2517 P64-8M-85-2517 P72-8M-85-3020 P80-8M-85-3020 P90-8M-85-3020 P112-8M-85-3020 P144-8M-85-3535 P192-8M-85-3535

DIAMETERS

PART NO.

NO. OF TEETH

P.D.

O.D.

112885 112886 114821 114822 112889 112890 112891 112892 112893 112894 112895 112896 112897 112898 112899 114833 112901

28 30 32 34 36 38 40 44 48 56 64 72 80 90 112 144 192

2.807 3.008 3.208 3.409 3.609 3.810 4.010 4.411 4.812 5.614 6.416 7.218 8.020 9.023 11.229 14.437 19.249

2.753 2.954 3.154 3.355 3.555 3.756 3.956 4.357 4.758 5.560 6.362 7.164 7.966 8.969 11.175 14.383 19.195

114823 114825 114828 114504 114505 114506 114507 114508 114509 114510 114511 114834 114513

34 36 40 44 48 56 64 72 80 90 112 144 192

3.409 3.609 4.010 4.411 4.812 5.614 6.416 7.218 8.020 9.023 11.229 14.437 19.249

3.355 3.555 3.956 4.357 4.758 5.560 6.362 7.164 7.966 8.969 11.175 14.383 19.195

DIMENSIONS (IN.)

FLANGE F = 2.38" 3.150 3.346 3.543 3.819 3.937 4.134 4.331 4.764 5.157 5.945 6.772 7.598 8.386 ... ... ... ... F = 3.75" 3.810 4.009 4.410 4.764 5.212 6.014 6.716 7.500 8.420 ... ... ... ...

TYPE

Bore Sizes

Approx. Approx. Weight WR^2 (LBS.) (Lb-Ft^2)

E

M

Min.

Max

A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1 A2 A3 A3

0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00

1.50 1.38 1.38 1.38 1.38 1.38 1.13 1.13 1.13 0.63 0.63 0.63 0.63 0.38 0.38 0.38 0.38

1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 7/8 7/8 7/8 7/8

1-1/8 1-1/4 1-1/4 1-11/16 1-11/16 1-11/16 2-1/8 2-1/8 2-1/8 2-11/16 2-11/16 2-11/16 2-11/16 3-1/4 3-1/4 3-1/4 3-1/4

2.1 2.2 2.3 4.0 2.7 3.1 3.5 4.3 5.5 8.1 12 16 20 27 30 49 108

0.0182 0.0231 0.0281 0.0457 0.0431 0.0540 0.0685 0.0999 0.1491 0.2957 0.5272 0.8625 1.343 2.277 3.746 8.988 32.21

A1F A1F A1F A1F A1F A1F A1F A1F A1F A1 A2 A3 A3

0.75 0.75 1.25 1.25 1.25 0.81 0.59 0.88 0.50 0.50 0.50 0.00 0.13

1.50 1.50 1.25 1.25 1.25 1.19 1.41 0.88 1.25 1.25 1.25 0.25 0.13

1/2 1/2 1/2 1/2 1/2 1/2 1/2 7/8 7/8 7/8 7/8 1-3/16 1-3/16

1-11/16 1-11/16 2-1/8 2-1/8 2-1/8 2-11/16 2-11/16 3-1/4 3-1/4 3-1/4 3-1/4 3-15/16 3-15/16

3.9 4.4 4.7 5.9 7.6 11 15 18 22 32 33 54 125

0.0547 0.0694 0.0970 0.1447 0.2146 0.4058 0.6987 1.121 1.642 2.846 4.621 11.06 39.63

14 MM SPROCKETS Conveyor Components

SPROCKET NUMBER

Engineering

14M-40 P28-14M-40-2012* P29-14M-40-2012 P30-14M-40-2012 P32-14M-40-2012 P34-14M-40-2012 P36-14M-40-2517 P38-14M-40-2517 P40-14M-40-2517 P44-14M-40-2517 P48-14M-40-2517 P52-14M-40-2517 P56-14M-40-2517 P60-14M-40-3020 P64-14M-40-3020 P68-14M-40-3020 P72-14M-40-3020 P80-14M-40-3020 P90-14M-40-3020 P112-14M-40-3020 P144-14M-40-3020 P168-14M-40-3020 P192-14M-40-3020

PART NO. 112902 112903 112904 112905 112906 112907 112908 112909 112910 112911 112912 112913 112914 112915 112916 112917 114840 114851 114470 114471 114852 114853

FEATURES/BENEFITS PAGES PT11-2

NO. OF TEETH 28 29 30 32 34 36 38 40 44 48 52 56 60 64 68 72 80 90 112 144 168 192

DIAMETERS P.D. 4.912 5.088 5.263 5.614 5.965 6.316 6.667 7.018 7.720 8.421 9.123 9.825 10.527 11.229 11.930 12.632 14.036 15.790 19.650 25.264 29.475 33.686

DIMENSIONS (IN.)

O.D.

FLANGE

4.802 4.978 5.153 5.504 5.855 6.206 6.557 6.908 7.610 8.311 9.013 9.715 10.417 11.119 11.820 12.522 13.926 15.680 19.540 25.154 29.265 33.576

F = 2.13" 5.560 5.560 6.125 6.125 6.500 6.875 7.219 7.500 8.343 8.937 9.687 10.375 11.062 11.750 12.500 13.187 14.625 ... ... ... ... ...

TYPE A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A2F A2F A2F A2F A3F A3 A3 A3 A3 A3

SPECIFICATIONS: BELTS PAGES PT11-17

E

M

Min.

Max

0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00

0.88 0.88 0.88 0.88 0.88 0.38 0.38 0.38 0.38 0.38 0.38 0.38 0.13 0.13 0.13 0.13 0.13 0.13 0.13 0.13 0.13 0.13

1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 7/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8

2-1/8 2-1/8 2-1/8 2-1/8 2-1/8 2-11/16 2-11/16 2-11/16 2-11/16 2-11/16 2-11/16 2-11/16 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4

SELECTION PAGES PT11-19

PT11-6

Bore Sizes

Approx. Approx. Weight WR^2 (LBS.) (Lb-Ft^2) 5.9 6.6 6.5 8.0 9.4 11 12 14 18 22 26 31 29 31 31 34 34 40 101 154 133 168

0.1531 0.1810 0.1935 0.2651 0.3498 0.4443 0.5658 0.7134 1.046 1.527 2.126 2.878 3.177 3.872 4.446 5.410 7.474 9.396 29.66 75.16 113.3 189.8

ENGINEERING/TECHNICAL PAGES PT11-64


DYNA-SYNC

SPECIFICATION HT TAPER-LOCK Sprockets TYPE A

TYPE B

TYPE C

14MM SPROCKETS SPROCKET NUMBER

PART NO.

NO. OF TEETH

DIAMETERS

TYPE

P.D. O.D. FLANGE 14M-55 F = 2.75" P28-14M-55-2012 112922 28 4.912 4.802 5.560 P29-14M-55-2012 112923 29 5.088 4.978 5.560 P30-14M-55-2517 114836 30 5.263 5.153 6.125 P32-14M-55-2517 112925 32 5.614 5.504 6.125 P34-14M-55-2517 112926 34 5.965 5.855 6.500 P36-14M-55-2517 112927 36 6.316 6.206 6.875 P38-14M-55-2517 112928 38 6.667 6.557 7.219 P40-14M-55-2517 112929 40 7.018 6.908 7.500 P44-14M-55-2517 112930 44 7.720 7.610 8.343 P48-14M-55-3020 112931 48 8.421 8.311 8.937 P52-14M-55-3020 112932 52 9.123 9.013 9.687 P56-14M-55-3020 112933 56 9.825 9.715 10.375 P60-14M-55-3020 112934 60 10.527 10.417 11.062 P64-14M-55-3020 112935 64 11.229 11.119 11.750 P68-14M-55-3020 112936 68 11.930 11.820 12.500 P72-14M-55-3020 112937 72 12.632 12.522 13.187 14.036 13.926 14.625 P80-14M-55-3020 114841 80 P90-14M-55-3020 114859 90 15.790 15.680 ... P112-14M-55-3020 114472 112 19.650 19.540 ... P144-14M-55-3020 114854 144 25.264 25.154 ... P168-14M-55-3020 114860 168 29.475 29.265 ... P192-14M-55-3535 114755 192 33.686 33.576 ... 14M-85 F = 4" P28-14M-85-2012* 112944 28 4.912 4.802 5.560 P29-14M-85-2012* 112945 29 5.088 4.978 5.560 P30-14M-85-2517 114837 30 5.263 5.153 6.125 P32-14M-85-2517 112947 32 5.614 5.504 6.125 34 5.965 5.855 6.500 P34-14M-85-2517 112948 P36-14M-85-3020 112949 36 6.316 6.206 6.875 P38-14M-85-3020 112950 38 6.667 6.557 7.219 P40-14M-85-3020 112951 40 7.018 6.908 7.500 P44-14M-85-3020 112952 44 7.720 7.610 8.343 P48-14M-85-3020 112953 48 8.421 8.311 8.937 P52-14M-85-3535 112954 52 9.123 9.013 9.687 P56-14M-85-3535 112955 56 9.825 9.715 10.375 P60-14M-85-3535 112956 60 10.527 10.417 11.062 11.229 11.119 11.750 64 P64-14M-85-3535 112957 P68-14M-85-3535 112958 68 11.930 11.820 12.500 P72-14M-85-3535 112959 72 12.632 12.522 13.187 P80-14M-85-3535 112960 80 14.036 13.926 14.625 P90-14M-85-3535 114474 90 15.790 15.680 ... P112-14M-85-3535 114844 112 19.650 19.540 ... P144-14M-85-4040 114855 144 25.264 25.154 ... P168-14M-85-4040 114489 168 29.475 29.265 ... P192-14M-85-4040 114850 192 33.686 33.576 ... TAPER-LOCK Sprockets limited to torque capacity of bushing.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS: BELTS PAGES PT11-17

DIMENSIONS (IN.) E M

Min.

Max

Approx. Approx. Weight WR^2 (LBS.) (Lb-Ft^2)

A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A2F A2F A3F A3 A3 A3 A3 C3

0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.19 0.00

1.50 1.50 1.00 1.00 1.00 1.00 1.00 1.00 1.00 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.56 0.75

1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 7/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8 1-3/16

2-1/8 2-1/8 2-11/16 2-11/16 2-11/16 2-11/16 2-11/16 2-11/16 2-11/16 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-15/16

7.4 8.4 7.4 9.3 11 12 14 17 20 24 30 35 42 48 40 45 42 45 117 98 146 432

0.1948 0.2314 0.2371 0.3276 0.4379 0.5400 0.6868 0.8719 1.234 1.840 2.573 3.489 4.647 6.012 5.909 7.387 9.021 12.36 36.86 65.38 150.2 404.3

A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A2F A1F A2F A2 A3 A3 A3 A3

1.31 1.31 0.50 0.81 0.81 0.53 0.53 0.53 0.53 0.53 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00

1.44 1.44 1.75 1.44 1.44 1.47 1.47 1.47 1.47 1.47 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.00 0.00 0.00

1/2 1/2 1/2 1/2 1/2 7/8 7/8 7/8 7/8 7/8 1-3/16 1-3/16 1-3/16 1-3/16 1-3/16 1-3/16 1-3/16 1-3/16 1-3/16 1-7/16 1-7/16 1-7/16

2-1/8 2-1/8 2-11/16 2-11/16 2-11/16 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-15/16 3-15/16 3-15/16 3-15/16 3-15/16 3-15/16 3-15/16 3-15/16 3-15/16 4-7/16 4-7/16 4-7/16

10 12 10 13 15 14 17 20 24 31 37 52 63 74 63 97 63 72 131 137 192 448

0.2787 0.3321 0.3326 0.4590 0.6143 0.6948 0.8975 1.161 1.615 2.432 3.356 5.300 7.128 9.334 9.169 15.19 13.04 18.14 44.18 92.10 194.5 444.6

SELECTION PAGES PT11-19

PT11-7

Bore Sizes

ENGINEERING/TECHNICAL PAGES PT11-64

Sprockets

TYPE CF

Conveyor Components

TYPE BF

Engineering

TYPE AF

HT Synchrous Belts

The figure following the sketch reference letter in the "Type" column indicates the construction of the sprocket (1 = Solid, 2 = Web, and 3 = Arms), and the letter "F" indicates that the sprocket has flanges.


DYNA-SYNC

SPECIFICATION HT TAPER-LOCK Sprockets NOMENCLATURE EXAMPLE P

44 — 8M — 20 — 2012 For 20 mm Wide Belt

44 Teeth HT Synchrous Belts

Sprocket

8 mm Pitch

Use 2012 Bushing (MPB - Minimum Plain Bore)

14MM SPROCKETS SPROCKET NUMBER

Sprockets Conveyor Components Engineering

14M-115 P30-14M-115-2517 P32-14M-115-2517 P34-14M-115-2517 P36-14M-115-3020 P38-14M-115-3020 P40-14M-115-3020 P44-14M-115-3535 P48-14M-115-3535 P52-14M-115-4040 P56-14M-115-4040 P60-14M-115-4040 P64-14M-115-4545 P68-14M-115-4545 P72-14M-115-4545 P80-14M-115-4545 P90-14M-115-4545 P112-14M-115-4545 P144-14M-115-4545 P168-14M-115-4545 P192-14M-115-4545 P216-14M-115-6050 14M-170 P40-14M-170-3535* P44-14M-170-3535 P48-14M-170-3535 P52-14M-170-4040 P56-14M-170-4040 P60-14M-170-4545 P64-14M-170-4545 P68-14M-170-4545 P72-14M-170-4545 P80-14M-170-4545 P90-14M-170-4545 P112-14M-170-4545 P144-14M-170-6050 P168-14M-170-6050 P192-14M-170-6050 P216-14M-170-6050

FEATURES/BENEFITS PAGES PT11-2

PART NO.

NO. OF TEETH

114838 114517 114518 114519 114494 114475 114522 114523 114524 114525 114526 114527 114528 114529 114530 114476 114477 114856 114848 114482 114857 114539 114540 114541 114542 114543 114544 114545 114546 114547 114548 114478 114479 114858 114499 117846 117848

DIAMETERS P.D.

O.D.

30 32 34 36 38 40 44 48 52 56 60 64 68 72 80 90 112 144 168 192 216

5.263 5.614 5.965 6.316 6.667 7.018 7.720 8.421 9.123 9.825 10.527 11.229 11.930 12.632 14.036 15.790 19.650 25.264 29.475 33.686 37.896

5.153 5.504 5.855 6.206 6.557 6.908 7.610 8.311 9.013 9.715 10.417 11.119 11.820 12.522 13.926 15.680 19.540 25.154 29.265 33.576 37.786

40 44 48 52 56 60 64 68 72 80 90 112 144 168 192 216

7.018 7.720 8.421 9.123 9.825 10.527 11.229 11.930 12.632 14.036 15.790 19.650 25.264 29.475 33.686 37.896

6.908 7.610 8.311 9.013 9.715 10.417 11.119 11.820 12.522 13.926 15.680 19.540 25.154 29.265 33.576 37.786

TYPE

FLANGE F = 5.25" 5.763 6.114 6.465 6.816 7.167 7.518 8.395 8.941 9.687 10.355 11.067 11.750 12.500 13.066 14.620 ... ... ... ... ... ... F = 7.38" 7.518 8.395 8.941 9.687 10.355 11.067 11.750 12.500 13.066 14.625 ... ... ... ... ... ...

SPECIFICATIONS: BELTS PAGES PT11-17

DIMENSIONS (IN.) E M

Min.

Max

Approx. Approx. Weight WR^2 (LBS.) (Lb-Ft^2)

A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A2F A2 A2 A3 A3 A3 A3

1.75 1.75 1.75 1.63 1.63 1.63 0.88 0.88 0.63 0.63 0.63 0.38 0.38 0.00 0.38 0.38 0.00 0.38 0.38 0.38 0.00

1.75 1.75 1.75 1.63 1.63 1.63 0.88 0.88 0.63 0.63 0.63 0.38 0.38 0.75 0.38 0.38 0.75 0.38 0.38 0.38 0.25

1/2 1/2 1/2 7/8 7/8 7/8 1-3/16 1-3/16 1-7/16 1-7/16 1-7/16 1-15/16 1-15/16 1-15/16 1-15/16 1-15/16 1-15/16 1-15/16 1-15/16 1-15/16 4-7/16

2-11/16 2-11/16 2-11/16 3-1/4 3-1/4 3-1/4 3-15/16 3-15/16 4-7/16 4-7/16 4-7/16 4-15/16 4-15/16 4-15/16 4-15/16 4-15/16 4-15/16 4-15/16 4-15/16 4-15/16 6

13 16 19 18 20 23 30 40 47 58 70 82 97 113 148 117 173 120 223 475 686

0.4386 0.5873 0.7908 0.8766 1.100 1.357 2.144 3.277 4.545 6.335 8.589 11.47 14.91 19.06 29.66 28.30 64.72 172.2 243.3 496.5 378.0

A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A2 D2 A3 A3 A3 A2

1.94 1.94 1.94 1.13 1.13 0.75 0.63 0.63 0.63 1.03 0.63 0.25 1.19 1.19 1.19 1.19

1.94 1.94 1.94 2.25 2.25 2.13 2.25 2.25 2.25 1.84 2.25 3.12 1.19 1.19 1.19 1.19

1-3/16 1-3/16 1-3/16 1-7/16 1-7/16 1-15/16 1-15/16 1-15/16 1-15/16 1-15/16 1-15/16 1-15/16 4-7/16 4-7/16 4-7/16 4-7/16

3-15/16 3-15/16 3-15/16 4-7/16 4-7/16 4-15/16 4-15/16 4-15/16 4-15/16 4-15/16 4-15/16 4-15/16 6 6 6 6

29 39 51 59 71 83 94 113 130 166 159 215 264 462 616 563

1.780 2.828 4.283 5.877 8.051 10.85 13.71 18.15 23.00 35.12 42.03 81.30 207.9 384.2 655.7 851.7

SELECTION PAGES PT11-19

PT11-8

Bore Sizes

ENGINEERING/TECHNICAL PAGES PT11-64


TYPE A

TYPE 6F

TYPE AF

PLAIN BORE HT SPROCKETS SPROCKET NUMBER

PART NO.

NO. OF TEETH

P22-8M-20-MPB P22-8M-30-MPB P24-8M-30-MPB P26-8M-30-MPB P28-8M-50-MPB P30-8M-50-MPB P38-8M-85-MPB

110700 110720 110721 110722 114484 110741 114827

22 22 24 26 28 30 38

P28-14M-85-MPB P29-14M-85-MPB P28-14M-115-MPB P29-14M-115-MPB P36-14M-170-MPB P38-14M-170-MPB P40-14M-170-MPB

110830 110831 110855 110856 110880 110881 110882

28 29 28 29 36 38 40

Pitch 8 MM 2.206 2.206 2.406 2.607 2.807 3.008 3.810 14 MM 4.912 5.088 4.912 5.088 6.316 6.667 7.018

FlN-FAN SPROCKETS 114852 114853 114860 114993 114994

168 192 168 192 216

114375 114376 114377 114378 114379 114380

168 192 144 168 192 216

O.D. Pitch 2.152 2.152 2.352 2.553 2.753 2.954 3.756 Pitch 4.802 4.978 4.802 4.978 6.206 6.557 6.908

FLANGE

Min.

Max

Approx. Weight (LBS.)

Bore Range

2.606 2.606 2.756 2.906 3.207 3.346 4.201

0.60 0.60 0.60 0.80 0.60 0.60 0.60

1.80 2.10 2.10 2.30 2.50 2.50 3.30

0.00 0.00 0.00 0.00 0.50 0.50 1.10

1/2 1/2 1/2 1/2 1/2 1/2 1/2

1-3/16 1-3/16 1-1/4 1-1/4 1-1/2 1-1/2 1-7/8

1.3 1.6 1.9 2.4 3.7 4.3 9.7

5.562 5.562 5.562 5.562 6.816 7.167 7.518

1.00 1.00 1.30 1.30 1.30 1.30 1.30

4.00 4.00 5.00 5.00 6.00 6.00 6.00

1.00 1.00 1.50 1.50 2.60 2.60 2.60

1-1/4 1-1/4 1-1/4 1-1/4 1-1/2 1-1/2 1-1/2

2-11/16 2-11/16 2-11/16 2-11/16 3-3/8 3-3/8 3-3/4

17 19 22 24 47 54 60

Approx. WR^2 (Lb-Ft^2)

Type 6F 0.0048 0.0060 0.0061 0.0087 0.0240 0.0319 0.1204 Type 6F 0.3128 0.3654 0.4077 0.4768 1.593 1.987 2.479

For Cooling Tower Drives 14 MM 29.475 33.686 29.475 33.686 37.896 14 MM 29.475 33.686 25.262 29.475 33.686 37.896

Pitch 29.265 33.576 29.265 33.576 37.786 Pitch 29.265 33.576 25.154 29.265 33.576 37.786

... ... ... ... ...

0.00 0.00 0.00 0.00 0.00

2.00 2.00 2.00 2.00 2.00

0.10 0.10 0.80 0.80 0.80

7/8 7/8 7/8 7/8 7/8

3-1/4 3-1/4 3-1/4 3-1/4 3-1/4

... ... ... ... ... ...

0.60 0.60 0.60 0.00 0.00 0.00

1.60 1.60 1.60 1.60 1.60 1.60

0.60 0.60 1.20 1.20 1.20 1.20

7/8 7/8 7/8 7/8 7/8 7/8

3-1/2 3-1/2 3-1/2 3-1/2 3-1/2 3-1/2

Type A 113.3 189.8 150.2 170.9 254.6 Type A 151.7 102.6 127.8 143.5 140.3 77.97 175.1 129.5 183.0 210.5 218.1 288.9 133 168 146 162 195

Engineering

TAPER-LOCK P168-14M-40-3020 P192-14M-40-3020 P168-14M-55-3020 F192-14M-55-3020 F216-14M-55-3020 QD F168-14M-55-E F192-14M-55-E F144-14M-85-E F168-14M-85-E F192-14M-85-E F216-14M-85-E

DIMENSIONS (INCHES) E L M

DIAMETERS

Sprockets

TYPE 6

Conveyor Components

HT Sprockets

HT Synchrous Belts

DYNA-SYNC

SPECIFICATION

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS: BELTS PAGES PT11-17

SELECTION PAGES PT11-19

PT11-9

ENGINEERING/TECHNICAL PAGES PT11-64


DYNA-SYNC

SPECIFICATION QD HTD Sprockets TYPE B F M

TYPE A M

K

F

K

K

OD

OD

OD

HT Synchrous Belts

TYPE AF

TYPE CF

TYPE BF TYPE E

TYPE D F M

F

K

The figure following the sketch reference letter in the "Type" column indicates the construction of the sprocket (1 = Solid, 2 = Web, and 3 = Arms), and the letter "F" indicates that the sprocket has flanges.

TYPE C F M

K

OD

OD

TYPE EF

TYPE DF

5MM QD HTD SPROCKETS SPROCKET NUMBER Sprockets Conveyor Components Engineering

5M-15 P38-5M-15-JA P40-5M-15-JA P44-5M-15-JA P48-5M-15-JA P52-5M-15-JA P56-5M-15-SH P60-5M-15-SH P64-5M-15-SH P68-5M-15-SDS P72-5M-15-SDS P80-5M-15-SDS P90-5M-15-SDS P112-5M-15-SDS 5M-25 P38-5M-25-JA P40-5M-25-JA P44-5M-25-JA P48-5M-25-JA P52-5M-25-JA P56-5M-25-SH P60-5M-25-SH P64-5M-25-SH P68-5M-25-SDS P72-5M-25-SDS P80-5M-25-SDS P90-5M-25-SDS P112-5M-25-SDS

PART NO.

NO. OF TEETH

114641 114642 114643 114644 114645 114646 114647 114648 114649 114650 114651 114652 114653 114655 114656 114657 114658 114659 114660 114661 114662 114663 114664 114665 114666 114667

FEATURES/BENEFITS PAGES PT11-2

DIAMETERS (INCHES) Pitch

O.D.

38 40 44 48 52 56 60 64 68 72 80 90 112

2.381 2.506 2.757 3.008 3.258 3.509 3.760 4.010 4.261 4.511 5.013 5.639 7.018

2.336 2.461 2.712 2.963 3.213 3.464 3.715 3.965 4.216 4.466 4.968 5.594 6.973

38 40 44 48 52 56 60 64 68 72 80 90 112

2.381 2.506 2.757 3.008 3.258 3.509 3.760 4.010 4.261 4.511 5.013 5.639 7.018

2.336 2.461 2.712 2.963 3.213 3.464 3.715 3.965 4.216 4.466 4.968 5.594 6.973

FLANGE F=0.89" 2.613 2.733 3.090 3.328 3.566 3.805 4.044 4.170 4.520 4.670 ... ... ... F=1.28" 2.613 2.733 3.090 3.328 3.566 3.805 4.044 4.170 4.520 4.670 ... ... ...

TYPE

DIMENSIONS (INCHES) M K

Bore Sizes Min.

Max

Approx. Approx. Weight WR^2 (LBS.) (Lb-Ft^2)

E1F E1F E1F D1F D1F E1F E1F E1F D1F D1F C1 C1 C1

0.00 0.00 0.00 0.31 0.31 0.00 0.00 0.00 0.14 0.14 0.14 0.14 0.14

0.51 0.51 0.51 0.20 0.20 0.68 0.68 0.68 0.56 0.56 0.56 0.56 0.56

1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2

1-1/4 1-1/4 1-1/4 1-1/4 1-1/4 1-11/16 1-11/16 1-11/16 2 2 2 2 2

0.6 0.7 0.9 0.9 1.1 1.5 1.8 2.1 2.1 2.4 3.1 4.1 6.9

0.0030 0.0039 0.0061 0.0076 0.0106 0.0169 0.0233 0.0312 0.0369 0.0463 0.0732 0.1204 0.3033

E1F E1F E1F B1F B1F C1F C1F C1F C1F C1F C1 C1 C1

0.00 0.00 0.00 0.72 0.72 0.47 0.47 0.47 0.53 0.53 0.53 0.53 0.53

0.51 0.51 0.51 0.21 0.21 0.21 0.21 0.21 0.17 0.17 0.17 0.17 0.17

1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2

1-1/4 1-1/4 1-1/4 1-1/4 1-1/4 1-11/16 1-11/16 1-11/16 2 2 2 2 2

0.9 1.0 1.3 1.1 1.3 1.7 2.1 2.4 2.6 2.8 3.6 4.7 7.7

0.0043 0.0056 0.0088 0.0097 0.0133 0.0206 0.0285 0.0379 0.0479 0.0564 0.0875 0.1414 0.3595

SPECIFICATIONS: BELTS PAGES PT11-17

SELECTION PAGES PT11-19

PT11-10

ENGINEERING/TECHNICAL PAGES PT11-64


DYNA-SYNC

SPECIFICATION QD HTD Sprockets K

M

TYPE B

F

M

K

K

OD

OD

OD

TYPE AF

TYPE C F M

F

TYPE CF

TYPE BF TYPE D F M

TYPE E F

K

K

OD

The figure following the sketch reference letter in the "Type" column indicates the construction of the sprocket (1 = Solid, 2 = Web, and 3 = Arms), and the letter "F" indicates that the sprocket has flanges.

OD

TYPE DF

HT Synchrous Belts

TYPE A

TYPE EF

NO. OF TEETH

110701 110702 110703 110704 110705 110706 110707 110708 111709 110710 110711 110712 110713 110714 110715 110716 110723 110724 110725 110726 110727 110728 110729 110730 110731 110732 110733 110734 110735 110736 110737

FEATURES/BENEFITS PAGES PT11-2

DIAMETERS (INCHES) Pitch

O.D.

FLANGE

24 26 28 30 32 34 36 38 40 44 48 56 64 72 80 90

2.406 2.607 2.807 3.008 3.208 3.409 3.609 3.810 4.010 4.411 4.812 5.614 6.416 7.218 8.020 9.023

2.352 2.553 2.759 2.958 3.156 3.355 3.555 3.756 3.956 4.357 4.758 5.560 6.362 7.164 7.966 8.969

28 30 32 34 36 38 40 44 48 56 64 72 80 90 112

2.807 3.008 3.208 3.409 3.609 3.810 4.010 4.411 4.812 5.614 6.416 7.218 8.020 9.023 11.229

2.759 2.958 3.156 3.355 3.555 3.756 3.956 4.357 4.758 5.560 6.362 7.164 7.966 8.969 11.175

2.756 2.906 3.207 3.408 3.608 3.810 4.009 4.210 4.410 4.764 5.212 6.014 6.716 7.500 8.420 ... F = 1.5" 3.207 3.408 3.608 3.810 4.009 4.210 4.410 4.764 5.212 6.014 6.716 7.500 8.420 ... ...

TYPE

DIMENSIONS (INCHES) M K

Bore Sizes Min.

Max

Approx. Approx. Weight WR^2 (LBS.) (Lb-Ft^2)

E1F E1F E1F E1F E1F E1F C1F C1F C1F C1F C1F C1F C1F C1F C1F C2

0.00 0.00 0.00 0.00 0.00 0.00 0.31 0.31 0.31 0.38 0.38 0.38 0.38 0.38 0.38 0.38

0.51 0.51 1.42 1.42 1.42 0.68 0.37 0.37 0.37 0.32 0.32 0.32 0.32 0.32 0.32 0.32

1/2 1/2 3/8 3/8 3/8 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2

1-1/4 1-1/4 1-1/2 1-1/2 1-1/2 1-11/16 1-11/16 2 2 2 2 2 2 2 2 2

0.8 1.0 1.1 1.3 1.6 1.6 1.7 2.0 2.3 2.6 3.4 4.6 6.8 8.8 11 12

0.0039 0.0059 0.0078 0.0110 0.0148 0.0181 0.0213 0.0272 0.0353 0.0490 0.0771 0.1370 0.2639 0.4298 0.6433 0.9369

E1F E1F E1F B1F B1F B1F B1F B1F B1F B1F C1F C1F C2 C2 C2

0.00 0.00 0.00 0.69 0.69 0.69 0.69 0.75 0.75 0.75 0.25 0.25 0.25 0.25 0.25

1.20 1.20 1.20 0.01 0.01 0.01 0.01 0.05 0.05 0.05 0.64 0.64 0.64 0.64 0.64

1/2 3/8 3/8 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2

1-1/2 1-1/2 1-1/2 1-11/16 1-11/16 1-11/16 1-11/16 2 2 2 2-5/8 2-5/8 2-5/8 2-5/8 2-5/8

1.4 1.8 2.1 1.6 2.0 2.3 2.8 3.0 3.8 5.2 8.6 12 11 16 22

0.0104 0.0146 0.0197 0.0186 0.0259 0.0328 0.0435 0.0595 0.0880 0.1633 0.3421 0.5710 0.6487 1.2862 2.703

SPECIFICATIONS: BELTS PAGES PT11-17

SELECTION PAGES PT11-19

PT11-11

ENGINEERING/TECHNICAL PAGES PT11-64

Conveyor Components

8M-20 P24-8M-20-JA P26-8M-20-JA P28-8M-20-QT P30-8M-20-QT P32-8M-20-QT P34-8M-20-SH P36-8M-20-SH P38-8M-20-SH P40-8M-20-SH P44-8M-20-SDS P48-8M-20-SDS P56-8M-20-SDS P64-8M-20-SDS P72-8M-20-SDS P80-8M-20-SDS P90-8M-20-SDS 8M-30 P28-8M-30-QT P30-8M-30-QT P32-8M-30-QT P34-8M-30-SH P36-8M-30-SH P38-8M-30-SH P40-8M-30-SH P44-8M-30-SDS P48-8M-30-SDS P56-8M-30-SDS P64-8M-30-SK P72-8M-30-SK P80-8M-30-SK P90-8M-30-SK P112-8M-30-SK

PART NO.

Engineering

SPROCKET NUMBER

Sprockets

8MM QD HTD SPROCKETS


DYNA-SYNC

SPECIFICATION QD HTD Sprockets TYPE A

K

TYPE C F M K

TYPE B F M

F M

K

OD

OD

HT Synchrous Belts

TYPE AF

OD

TYPE CF

TYPE BF TYPE E

TYPE D F M

F

K

K

OD

The figure following the sketch reference letter in the "Type" column indicates the construction of the sprocket (1 = Solid, 2 = Web, and 3 = Arms), and the letter "F" indicates that the sprocket has flanges.

OD

TYPE EF

TYPE DF

8MM QD HTD SPROCKETS SPROCKET NUMBER Sprockets Conveyor Components Engineering

8M-50 P28-8M-50-JA P30-8M-50-JA P32-8M-50-QT P34-8M-50-SH P36-8M-50-SH P38-8M-50-SH P40-8M-50-SH P44-8M-50-SD P48-8M-50-SD P56-8M-50-SK P64-8M-50-SK P72-8M-50-SK P80-8M-50-SF P90-8M-50-SF P112-8M-50-SF P144-8M-50-E P192-8M-50-E 8M-85 P34-8M-85-SH P36-8M-85-SH P38-8M-85-SH P40-8M-85-SD P44-8M-85-SD P48-8M-85-SD P56-8M-85-SK P64-8M-85-SK P72-8M-85-SF P80-8M-85-SF P90-8M-85-SF P112-8M-85-SF P144-8M-85-E P192-8M-85-E

PART NO.

NO. OF TEETH

110738 110739 110742 110743 110744 110745 110746 110747 110748 110749 110750 110751 110752 110753 110754 110755 110756 110760 110761 110762 110763 110764 110765 110766 110767 110768 110769 110770 110771 110772 110773

FEATURES/BENEFITS PAGES PT11-2

DIAMETERS (INCHES) PITCH

O.D.

28 30 32 34 36 38 40 44 48 56 64 72 80 90 112 144 192

2.807 3.008 3.208 3.409 3.609 3.810 4.010 4.411 4.812 5.614 6.416 7.218 8.020 9.023 11.229 14.437 19.249

2.759 2.958 3.156 3.355 3.555 3.756 3.956 4.357 4.758 5.560 6.362 7.164 7.966 8.969 11.175 14.383 19.195

34 36 38 40 44 48 56 64 72 80 90 112 144 192

3.409 3.609 3.810 4.010 4.411 4.812 5.614 6.42 7.218 8.020 9.023 11.229 14.437 19.249

3.355 3.555 3.756 3.956 4.357 4.758 5.560 6.362 7.164 7.966 8.969 11.175 14.383 19.195

FLANGE F = 2.38" 3.207 3.408 3.608 3.810 4.009 4.210 4.410 4.764 5.212 6.014 6.716 7.500 8.420 ... ... ... ... F = 3.75" 3.810 4.009 4.210 4.410 4.764 5.212 6.014 6.716 7.500 8.420 ... ... ... ...

TYPE

DIMENSIONS (INCHES) M K

BORE SIZES MIN.

MAX.

Approx. Approx. Weight WR^2 (Lbs.) (Lb-Ft^2)

A1F A1F A1F D1F D1F D1F D1F D1F D1F D1F D1F D1F D1F D1 D2 D3 D3

0.81 0.81 0.81 0.50 0.50 0.50 0.50 0.56 0.56 0.56 0.56 0.56 0.56 0.56 0.75 0.38 0.38

0.30 0.30 0.30 0.18 0.18 0.18 0.18 1.74 1.74 0.33 0.33 0.33 0.38 0.38 0.19 0.82 0.82

1/2 1/2 3/8 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 7/8 7/8

1-1/4 1-1/4 1-1/2 1-11/16 1-11/16 1-11/16 1-11/16 2 2 2-15/16 2-15/16 2-15/16 2-15/16 2-15/16 2-15/16 3-1/2 3-1/2

1.7 1.9 2.1 2.2 2.8 3.1 3.9 5.5 7.2 11 10 16 20 25 32 45 65

0.0127 0.0172 0.0214 0.0263 0.0367 0.0462 0.0632 0.1068 0.1644 0.3314 0.4400 0.8488 1.335 2.102 4.152 9.391 20.42

A1F A1F A1F A1F A1F A1F A1F A1F A1F A1F A1 A2 D3 D3

1.50 1.50 1.50 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.06 1.06

0.82 0.82 0.82 0.55 0.55 0.55 0.36 0.36 0.31 0.31 0.31 0.31 0.14 0.14

1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 7/8 7/8

1-11/16 1-11/16 1-11/16 2 2 2 2-5/8 2-5/8 2-15/16 2-15/16 2-15/16 2-15/16 3-1/2 3-1/2

3.1 3.9 4.4 4.9 7.8 11 12 17 19 29 26 38 61 76

0.0376 0.0535 0.0671 0.0836 0.1589 0.2496 0.4191 0.7664 1.114 1.982 2.253 5.286 14.031 26.80

SPECIFICATIONS: BELTS PAGES PT11-17

SELECTION PAGES PT11-19

PT11-12

ENGINEERING/TECHNICAL PAGES PT11-64


110780 110781 110782 110783 110784 110785 110786 110787 110788 110789 110790 110791 110792 110793 110794 110795 110796 110797 110798 110799 110759 110774

DIAMETERS (INCHES) PITCH

O.D.

28 29 30 32 34 36 38 40 44 48 52 56 60 64 68 72 80 90 112 144 168 192

4.912 5.088 5.263 5.614 5.965 6.316 6.667 7.018 7.720 8.421 9.123 9.825 10.527 11.229 11.930 12.632 14.036 15.790 19.650 25.264 29.475 33.686

4.808 4.983 5.157 5.507 5.858 6.208 6.559 6.909 7.610 8.311 9.013 9.715 10.417 11.119 11.820 12.522 13.926 15.680 19.540 25.154 29.265 33.576

110805 110806 110807 110808 110809 110810 110811 110812 110813 110814 110815 110816 110817 110818 110819 110820 110821 110822 110823 110824 110825 110826 110827

28 29 30 32 34 36 38 40 44 48 52 56 60 64 68 72 80 90 112 144 168 192 216

4.912 5.088 5.263 5.614 5.965 6.316 6.667 7.018 7.720 8.421 9.123 9.825 10.527 11.229 11.930 12.632 14.036 15.790 19.650 25.264 29.475 33.686 37.896

4.808 4.983 5.157 5.507 5.858 6.208 6.559 6.909 7.610 8.311 9.013 9.715 10.417 11.119 11.820 12.522 13.926 15.680 19.540 25.154 29.265 33.576 37.786

110832 110833 110834 110835 110836 110837 110838 110839 110840 110841 110842 110843 110852 110844 110845 110846 110847 110848 110849 110850 110851

30 32 34 36 38 40 44 48 52 56 60 64 68 72 80 90 112 144 168 192 216

5.263 5.614 5.965 6.316 6.667 7.018 7.720 8.421 9.123 9.825 10.527 11.229 11.930 12.632 14.036 15.790 19.650 25.264 29.475 33.686 37.896

5.157 5.507 5.858 6.208 6.559 6.909 7.610 8.311 9.013 9.715 10.417 11.119 11.820 12.522 13.926 15.680 19.540 25.154 29.265 33.576 37.786

FEATURES/BENEFITS PAGES PT11-2

FLANGE F = 2.13" 5.562 5.562 5.763 6.114 6.465 6.816 7.167 7.518 8.395 8.941 9.687 10.355 11.067 11.750 12.500 13.066 14.620 ... ... ... ... ... F = 2.75" 5.562 5.562 5.763 6.114 6.465 6.816 7.167 7.518 8.395 8.941 9.687 10.355 11.067 11.750 12.500 13.066 14.620 ... ... ... ... ... ... F = 4" 5.763 6.114 6.465 6.816 7.167 7.518 8.395 8.941 9.687 10.355 11.067 11.750 12.500 13.066 14.620 ... ... ... ... ... ...

TYPE

DIMENSIONS (INCHES) M K

MIN.

MAX.

Approx Weight (LBS.)

BORE SIZES

Approx. WR^2 (Lb-Ft^2)

E1F E1F D1F D1F D1F D1F D1F D1F D1F D1F D1F D1F D1F D1F D2F D2F D3F D3 D3 D3 C3 C3

0.00 0.00 0.44 0.44 0.44 0.44 0.44 0.44 0.38 0.38 0.25 0.25 0.44 0.44 0.44 0.31 0.44 0.25 0.25 0.25 0.37 0.37

0.89 0.89 0.45 0.45 0.45 0.50 0.50 0.50 0.82 0.82 0.95 0.95 0.76 0.76 0.76 0.89 0.76 0.95 0.95 0.95 1.79 1.79

0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.875 0.875 0.875 0.875 0.875 0.875 0.875 0.875 0.875 0.875 0.875 0.875 1 1

2-5/8 2-5/8 2-5/8 2-5/8 2-5/8 2-15/16 2-15/16 2-15/16 3-1/2 3-1/2 3-1/2 3-1/2 3-1/2 3-1/2 3-1/2 3-1/2 3-1/2 3-1/2 3-1/2 3-1/2 4 4

5.8 6.5 6.2 7.8 9.4 9.6 12 13 16 20 25 29 34 39 34 40 39 40 67 66 91 108

0.1301 0.1561 0.1629 0.2310 0.3113 0.3693 0.5080 0.6096 0.9305 1.360 1.991 2.583 3.494 4.489 4.368 5.811 7.005 8.633 21.62 38.99 74.83 117.1

E1F E1F D1F D1F D1F D1F D1F D1F D1F D1F D1F D1F D1F D1F D1F D1F D1F D2 D3 D3 D3 D3 D3

0.00 0.00 0.75 0.75 0.75 0.75 0.75 0.75 0.56 0.56 0.56 0.56 0.56 0.13 0.13 0.13 0.13 0.13 0.13 0.13 0.13 0.13 0.13

0.89 0.89 0.14 0.14 0.14 0.19 0.19 0.19 0.64 0.64 0.64 0.64 0.64 1.29 1.29 1.29 1.29 1.29 1.29 1.29 1.29 1.29 1.29

0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.875 0.875 0.875 0.875 0.875 1 1 1 1 1 1 1 1 1 1

2-5/8 2-5/8 2-5/8 2-5/8 2-5/8 2-15/16 2-15/16 2-15/16 3-1/2 3-1/2 3-1/2 3-1/2 3-1/2 4 4 4 4 4 4 4 4 4 4

7.3 8.2 7.5 9.5 11 11 14 15 19 23 30 32 38 54 62 71 89 61 80 90 111 134 159

0.1657 0.1991 0.1989 0.2868 0.3851 0.4515 0.6139 0.7440 1.136 1.641 2.454 3.030 4.038 6.267 8.029 10.32 15.76 12.67 25.72 55.45 95.26 149.7 223.9

A1F A1F A1F A1F A1F A1F D1F D1F D1F D1F D1F D1F D1F D1F D1F D3 D3 D3 D3 D3 D3

1.38 1.38 1.38 1.5 1.38 1.38 1.19 1.19 1.19 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.69 0.69 0.69

0.49 0.49 0.49 0.56 0.44 0.44 0.01 0.01 0.01 0.67 0.67 0.67 0.67 0.67 0.67 0.67 0.67 0.67 0.73 0.73 0.73

1/2 1/2 1/2 1/2 1/2 1/2 7/8 7/8 7/8 1 1 1 1 1 1 1 1 1 1 1 1

2-11/16 2-5/8 2-5/8 2-15/16 2-15/16 2-15/16 3-1/2 3-1/2 3-1/2 4 4 4 4 4 4 4 4 4 4 4 4

10 13 15 15 19 22 23 29 35 46 57 64 75 89 100 57 94 129 144 178 216

0.2715 0.3993 0.5387 0.6171 0.8559 1.097 1.390 2.133 2.972 4.426 6.259 7.866 10.40 13.74 18.65 12.19 32.92 73.66 126.7 203.8 315.6

SPECIFICATIONS: BELTS PAGES PT11-17

SELECTION PAGES PT11-19

PT11-13

ENGINEERING/TECHNICAL PAGES PT11-64

DYNA-SYNC

NO. OF TEETH

HT Synchrous Belts

14M-40 P28-14M-40-SK P29-14M-40-SK P30-14M-40-SK P32-14M-40-SK P34-14M-40-SK P36-14M-40-SF P38-14M-40-SF P40-14M-40-SF P44-14M-40-E P48-14M-40-E P52-14M-40-E P56-14M-40-E P60-14M-40-E P64-14M-40-E P68-14M-40-E P72-14M-40-E P80-14M-40-E P90-14M-40-E P112-14M-40-E P144-14M-40-E P168-14M-40-F P192-14M-40-F 14M-55 P28-14M-55-SK P29-14M-55-SK P30-14M-55-SK P32-14M-55-SK P34-14M-55-SK P36-14M-55-SF P38-14M-55-SF P40-14M-55-SF P44-14M-55-E P48-14M-55-E P52-14M-55-E P56-14M-55-E P60-14M-55-E P64-14M-55-F P68-14M-55-F P72-14M-55-F P80-14M-55-F P90-14M-55-F P112-14M-55-F P144-14M-55-F P168-14M-55-F P192-14M-55-F P216-14M-55-F 14M-85 P30-14M-85-SK P32-14M-85-SK P34-14M-85-SK P36-14M-85-SF P38-14M-85-SF P40-14M-85-SF P44-14M-85-E P48-14M-85-E P52-14M-85-E P56-14M-85-F P60-14M-85-F P64-14M-85-F P68-14M-85-F P72-14M-85-F P80-14M-85-F P90-14M-85-F P112-14M-85-F P144-14M-85-F P168-14M-85-F P192-14M-85-F P216-14M-85-F

PART NO.

Sprockets

SPROCKET NUMBER

Conveyor Components

14MM QD HTD Sprockets

Engineering

SPECIFICATION


DYNA-SYNC

SPECIFICATION QD HTD Sprockets TYPE A

TYPE B F M

F K

M

K

K

OD

OD

TYPE C F M

OD

TYPE CF

TYPE BF

TYPE AF

HT Synchrous Belts

TYPE D F M

TYPE E F

K

K

OD

The figure following the sketch reference letter in the "Type" column indicates the construction of the sprocket (1 = Solid, 2 = Web, and 3 = Arms), and the letter "F" indicates that the sprocket has flanges.

OD

TYPE DF

TYPE EF

14MM QD HTD SPROCKETS SPROCKET NUMBER

Sprockets Conveyor Components Engineering

14M-115 P30-14M-115-SK P32-14M-115-SK P34-14M-115-SK P36-14M-115-SF P38-14M-115-SF P40-14M-115-SF P44-14M-115-E P48-14M-115-E P52-14M-115-F P56-14M-115-F P60-14M-115-F P64-14M-115-J P68-14M-115-J P72-14M-115-J P80-14M-115-J P90-14M-115-J P112-14M-115-J P144-14M-115-J P168-14M-115-J P192-14M-115-J P216-14M-115-J 14M-170 P44-14M-170-E P48-14M-170-E P52-14M-170-F P56-14M-170-F P60-14M-170-J P64-14M-170-J P68-14M-170-J P72-14M-170-J P80-14M-170-J P90-14M-170-J P112-14M-170-M P144-14M-170-M P168-14M-170-M P192-14M-170-M P216-14M-170-M

PART NO.

NO. OF TEETH

110857 110858 110859 110860 110861 110862 110863 110864 110865 110866 110867 110868 110869 110870 110871 110872 110873 110874 110875 110876 110877 110883 110884 110885 110886 110887 110888 110897 110889 110890 110891 110892 110893 110894 110895 110896

FEATURES/BENEFITS PAGES PT11-2

DIAMETERS (INCHES) PITCH

O.D.

30 32 34 36 38 40 44 48 52 56 60 64 68 72 80 90 112 144 168 192 216

5.263 5.614 5.965 6.316 6.667 7.018 7.720 8.421 9.123 9.825 10.527 11.229 11.930 12.632 14.036 15.790 19.650 25.264 29.475 33.686 37.896

5.157 5.507 5.858 6.208 6.559 6.909 7.610 8.311 9.013 9.715 10.417 11.119 11.820 12.522 13.926 15.680 19.540 25.154 29.265 33.576 37.786

44 48 52 56 60 64 68 72 80 90 112 144 168 192 216

7.720 8.421 9.123 9.825 10.527 11.229 11.930 12.632 14.036 15.790 19.650 25.264 29.475 33.686 37.896

7.610 8.311 9.013 9.715 10.417 11.119 11.820 12.522 13.926 15.680 19.540 25.154 29.265 33.576 37.786

FLANGE F = 5.25" 5.763 6.114 6.465 6.816 7.167 7.518 8.395 8.941 9.687 10.355 11.067 11.750 12.500 13.066 14.620 ... ... ... ... ... ... F = 7.38" 8.395 8.941 9.687 10.355 11.067 11.750 12.500 13.066 14.620 ... ... ... ... ... ...

DIMENSIONS (INCHES) M K

MIN.

A1F A1F A1F A1F A1F A1F A1F A1F D1F D1F D1F D1F D1F D1F D2F D2 D3 D3 D3 D3 D3

2.00 2.00 2.00 2.00 2.00 2.00 2.00 1.94 1.38 1.38 1.38 1.00 1.00 1.00 1.00 1.00 1.00 1.06 1.06 1.06 1.06

1.11 1.11 1.11 1.06 1.06 1.06 0.80 0.74 0.05 0.05 0.05 0.20 0.20 0.20 0.20 0.20 0.20 0.14 0.14 0.14 0.14

A1F A1F A1F A1F A1F A1F A1F A1F A2F A2 D3 D3 D3 D3 D3

2.88 2.88 2.44 2.44 2.28 2.13 2.13 2.13 2.13 2.13 1.44 1.44 1.44 1.44 1.44

1.68 1.68 1.02 1.02 1.08 0.93 0.93 0.93 0.93 0.93 0.30 0.30 0.30 0.30 0.30

TYPE

SPECIFICATIONS: BELTS PAGES PT11-17

SELECTION PAGES PT11-19

PT11-14

MAX.

Approx. Weight (Lbs.)

Approx. WR^2 (Lb-Ft^2)

1/2 1/2 1/2 1/2 1/2 1/2 7/8 7/8 1 1 1 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2

2-5/8 2-5/8 2-5/8 2-15/16 2-15/16 2-15/16 3-1/2 3-1/2 4 4 4 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2

12 16 20 19 22 26 27 36 48 54 63 81 90 101 108 121 117 157 198 240 284

0.3441 0.5084 0.7035 0.7834 1.000 1.306 1.717 2.657 4.133 5.326 7.105 10.377 12.89 16.06 21.04 29.10 46.65 113.9 209.1 265.8 401.7

7/8 7/8 1 1 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 2 2 2 2 2

3-1/2 3-1/2 4 4 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 5-1/2 5-1/2 5-1/2 5-1/2 5-1/2

35 46 61 67 81 100 108 119 129 163 188 240 279 541 443

2.273 3.550 5.430 6.860 9.546 13.31 16.08 19.72 26.66 41.42 63.86 146.9 247.5 746.7 774.6

BORE SIZES

ENGINEERING/TECHNICAL PAGES PT11-64


20M-115 P34-20M-115-F P36-20M-115-F P38-20M-115-F P40-20M-115-F P44-20M-115-F P48-20M-115-J P52-20M-115-J P56-20M-115-J P60-20M-115-J P64-20M-115-J P68-20M-115-J P72-20M-115-J P80-20M-115-M P90-20M-115-M P112-20M-115-M P144-20M-115-N P168-20M-115-N P192-20M-115-N P216-20M-115-N 20M-170 P34-20M-170-MPB P36-20M-170-MPB P38-20M-170-J P40-20M-170-J P44-20M-170-J P48-20M-170-M P52-20M-170-M P56-20M-170-M P60-20M-170-M P64-20M-170-M P68-20M-170-M P72-20M-170-M P80-20M-170-M P90-20M-170-M P112-20M-170-N P144-20M-170-N P168-20M-170-P P192-20M-170-P P216-20M-170-P 20M-230 P38-20M-230-MPB P40-20M-230-MPB P44-20M-230-MPB P48-20M-230-M P52-20M-230-M P56-20M-230-M P60-20M-230-M P64-20M-230-M P68-20M-230-N P72-20M-230-N P80-20M-230-N P90-20M-230-N P112-20M-230-N P144-20M-230-P P168-20M-230-P P192-20M-230-W P216-20M-230-W

PART NO.

NO. OF TEETH

114668 114669 114670 114671 114672 114673 114674 114675 114676 114677 114678 114679 114680 114681 114682 114683 114684 114685 114686

34 36 38 40

DIAMETERS (INCHES) Pitch

O.D.

48 52 56 60 64 68 72 80 90 112 144 168 192 216

8.522 9.023 9.524 10.026 11.028 12.031 13.033 14.036 15.038 16.041 17.032 18.046 20.051 22.557 28.071 36.092 42.107 48.122 54.136

8.352 8.853 9.354 9.855 10.858 11.861 12.863 13.856 14.868 15.871 16.873 17.876 19.881 22.387 27.901 35.922 41.937 47.952 53.958

114687 114688 114689 114690 114691 114692 114693 114694 114695 114696 114697 114698 114699 114700 114701 114702 114703 114704 114705

34 36 38 40 44 48 52 56 60 64 68 72 80 90 112 144 168 192 216

8.522 9.023 9.524 10.026 11.028 12.031 13.033 14.036 15.038 16.041 17.032 18.046 20.051 22.557 28.071 36.092 42.107 48.122 54.136

8.352 8.853 9.354 9.855 10.858 11.861 12.863 13.856 14.868 15.871 16.873 17.876 19.881 22.387 27.901 35.922 41.937 47.952 53.958

114706 114707 114708 114709 114710 114711 114712 114713 114714 114715 114716 114717 114718 114719 114720 114721 114722

38 40 44 48 52

9.524 10.026 11.028 12.031 13.033 14.036 15.038 16.041 17.032 18.046 20.051 22.557 28.071 36.092 42.107 48.122 54.136

9.354 9.855 10.858 11.861 12.863 13.856 14.868 15.871 16.873 17.876 19.881 22.387 27.901 35.922 41.937 47.952 53.958

FEATURES/BENEFITS PAGES PT11-2

60 64 68 72 80 90 112 144 168 192 216

FLANGE F = 5.38" 9.449 9.843 10.443 10.827 11.811 12.795 13.764 14.764 15.927 16.929 17.927 18.898 20.866 23.425 ... ... ... ... ... F = 7.5" 9.449 9.843 10.443 10.827 11.811 12.795 13.764 14.764 15.927 16.929 17.927 18.898 20.866 23.425 ... ... ... ... ... F = 9.88" 10.443 10.827 11.811 12.795 13.764 14.764 15.927 16.929 17.927 18.898 20.866 23.425 ... ... ... ... ...

SPECIFICATIONS: BELTS PAGES PT11-17

TYPE

DIMENSIONS (INCHES) M K

Max

A1F A1F A1F A1F A1F D1F D2F D2F D2F D2F D2F D2F D2F D2F D3 C3 C3 C3 C3

1.44 1.44 1.44 1.44 1.44 1.19 1.19 1.19 1.19 1.19 1.19 1.19 0.19 0.19 0.19 0.00 0.00 0.00 0.00

0.02 0.02 0.02 0.02 0.02 0.01 0.01 0.01 0.01 0.01 0.01 0.01 1.55 1.55 1.55 2.05 2.05 2.05 2.05

1 1 1 1 1 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 2 2 2 2-7/16 2-7/16 2-7/16 2-7/16

4 4 4 4 4 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 5-1/2 5-1/2 5-1/2 5-7/8 5-7/8 5-7/8 5-7/8

42 50 55 61 74 100 96 103 110 119 125 135 216 247 273 392 469 552 618

6F 6F A1F A1F A1F D1F D1F D1F D1F D2F D2F D2F D2F D2F D3 D3 C3 C3 C3

2.25 2.25 2.19 2.19 2.19 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.25 1.25 1.06 1.06 1.06

1.25 1.25 0.99 0.99 0.99 0.24 0.24 0.24 0.24 0.24 0.24 0.24 0.24 0.24 0.80 0.80 1.24 1.24 1.24

2-1/8 2-1/8 1-1/2 1-1/2 1-1/2 2 2 2 2 2 2 2 2 2 2-7/16 2-7/16 2-7/16 2-7/16 2-7/16

4-3/8 4-1/2 4-1/2 4-1/2 4-1/2 5-1/2 5-1/2 5-1/2 5-1/2 5-1/2 5-1/2 5-1/2 5-1/2 5-1/2 5-7/8 5-7/8 7 7 7

81 93 72 80 97 148 175 204 233 210 222 230 249 285 361 478 658 739 901

6F 6F 6F A1F A1F A1F A1F A2F D1F D2F D2F D2F D3 D3 D3 C3 C3

2.63 2.63 2.63 2.00 2.00 2.00 2.00 2.00 1.81 1.81 1.81 1.81 1.81 1.31 1.31 1.50 1.50

1.25 1.25 1.25 0.26 0.26 0.26 0.26 0.26 0.24 0.24 0.24 0.24 0.24 0.99 0.99 1.06 1.06

2-7/8 2-7/8 2-7/8 2 2 2 2 2 2-7/16 2-7/16 2-7/16 2-7/16 2-7/16 2-15/16 2-15/16 4 4

5-1/4 5-7/8 6 5-1/2 5-1/2 5-1/2 5-1/2 5-1/2 5-7/8 5-7/8 5-7/8 5-7/8 5-7/8 7 7 8-1/2 8-1/2

120 147 180 164 193 224 252 233 375 339 331 370 409 622 742 1111 1238

SELECTION PAGES PT11-19

PT11-15

Min.

Approx. Weight (LBS.)

Bore Sizes

ENGINEERING/TECHNICAL PAGES PT11-64

Sprockets

SPROCKET NUMBER

Conveyor Components

20MM QD HTD Sprockets

Engineering

QD HTD Sprockets

HT Synchrous Belts

DYNA-SYNC

SPECIFICATION


DYNA-SYNC

SPECIFICATION QD HTD Sprockets TYPE A

TYPE C F M

TYPE B F M

F M

K

K

K

OD

OD

HT Synchrous Belts

TYPE AF

OD

TYPE CF

TYPE BF TYPE E

TYPE D F M

F

K

K

OD

The figure following the sketch reference letter in the "Type" column indicates the construction of the sprocket (1 = Solid, 2 = Web, and 3 = Arms), and the letter "F" indicates that the sprocket has flanges.

OD

TYPE EF

TYPE DF

20MM QD HTD SPROCKETS SPROCKET NUMBER Sprockets Conveyor Components Engineering

20M-290 P52-20M-290-N P56-20M-290-N P60-20M-290-N P64-20M-290-N P68-20M-290-N P72-20M-290-N P80-20M-290-N P90-20M-290-N P112-20M-290-P P144-20M-290-P P168-20M-290-W P192-20M-290-W P216-20M-290-W 20M-340 P52-20M-340-N P56-20M-340-N P60-20M-340-N P64-20M-340-N P68-20M-340-N P72-20M-340-N P80-20M-340-P P90-20M-340-P P112-20M-340-P P144-20M-340-W P168-20M-340-W P192-20M-340-S P216-20M-340-S

FEATURES/BENEFITS PAGES PT11-2

PART NO.

NO. OF TEETH

114723 114724 114725 114726 114727 114728 114729 114730 114731 114732 114733 114734 114735 114736 114737 114738 114739 114740 114741 114742 114743 114744 114745 114746 114747 114748

DIAMETERS (INCHES) Pitch

O.D.

52 56 60 64 68 72 80 90 112 144 168 192 216

13.033 14.036 15.038 16.041 17.032 18.046 20.051 22.557 28.071 36.092 42.107 48.122 54.136

12.863 13.856 14.868 15.871 16.873 17.876 19.881 22.387 27.901 35.922 41.937 47.952 53.958

52 56 60 64 68 72 80 90 112 144 168 192 216

13.033 14.036 15.038 16.041 17.032 18.046 20.051 22.557 28.071 36.092 42.107 48.122 54.136

12.863 13.856 14.868 15.871 16.873 17.876 19.881 22.387 27.901 35.922 41.937 47.952 53.958

FLANGE F = 12.25” 13.764 14.764 15.927 16.929 17.927 18.898 20.866 23.425 ... ... ... ... ... F = 14.25” 13.764 14.764 15.927 16.929 17.927 18.898 20.866 23.425 ... ... ... ... ...

TYPE

DIMENSIONS (INCHES) M K

Bore Sizes Min.

Max

WT. (LBS)

A1F A1F A1F A1F A1F A2F A2F A2F A2 A3 A3 A3 A3

2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.69 2.69 2.69

0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.25 0.25 0.19 0.19 0.19

2-7/16 2-7/16 2-7/16 2-7/16 2-7/16 2-7/16 2-7/16 2-7/16 2-15/16 2-15/16 4 4 4

5-7/8 5-7/8 5-7/8 5-7/8 5-7/8 5-7/8 5-7/8 5-7/8 7 7 8-1/2 8-1/2 8-1/2

202.7 238.8 276.5 319.8 367.9 364.0 369.6 424.3 614.6 679.8 1117.1 1281.0 1175.6

A1F A1F A1F A1F A1F A2F A1F A2F A2 A3 A3 D3 D3

2.50 2.50 2.50 2.50 2.50 2.50 3.50 3.50 3.50 2.63 2.63 1.13 1.13

0.50 0.50 0.50 0.50 0.50 0.50 1.25 1.25 1.25 0.13 0.13 2.38 2.38

2-7/16 2-7/16 2-7/16 2-7/16 2-7/16 2-7/16 2-15/16 2-15/16 2-15/16 4 4 5-1/2 5-1/2

5-7/8 5-7/8 5-7/8 5-7/8 5-7/8 5-7/8 7 7 7 8-1/2 8-1/2 10 10

221.0 258.0 293.4 337.9 388.1 393.1 560.0 497.3 653 3 851.0 1177.0 1519.4 1473.5

SPECIFICATIONS: BELTS PAGES PT11-17

SELECTION PAGES PT11-19

PT11-16

ENGINEERING/TECHNICAL PAGES PT11-64


Pitch Length (mm)

Tooth Pitch Spacing (mm)

Belt Width (mm)

5 MM Pitch HT200 Belts 15MM Wide Description P/N 300-5M-15 142100 355-5M-15 142101 375-5M-15 142102 400-5M-15 142103 405-5M-15 142145 425-5M-15 142104 450-5M-15 142105 500-5M-15 142106 535-5M-15 142107 565-5M-15 142108 580-5M-15 142146 600-5M-15 142109 625-5M-15 142147

Wgt. 0.04 0.05 0.05 0.05 0.05 0.06 0.06 0.07 0.07 0.08 0.08 0.08 0.09

15MM Wide Description P/N 650-5M-15 142110 700-5M-15 142111 750-5M-15 142112 800-5M-15 142113 850-5M-15 142148 900-5M-15 142114 1000-5M-15 142115 1150-5M-15 142116 1300-5M-15 142117 1450-5M-15 142118 1600-5M-15 142119 1720-5M-15 142120 2100-5M-15 142121

Wgt. 0.09 0.09 0.10 0.11 0.11 0.12 0.14 0.16 0.18 0.20 0.22 0.23 0.29

25MM Wide Description P/N 300-5M-25 142122 355-5M-25 142123 375-5M-25 142124 400-5M-25 142125 405-5M-25 142149 425-5M-25 142126 450-5M-25 142127 500-5M-25 142128 535-5M-25 142129 565-5M-25 142130 580-5M-25 142150 600-5M-25 142131 625-5M-25 142151

Wgt. 0.07 0.08 0.09 0.09 0.09 0.10 0.10 0.11 0.12 0.13 0.13 0.14 0.14

25MM Wide Description P/N 650-5M-25 142132 700-5M-25 142133 750-5M-25 142134 800-5M-25 142135 850-5M-25 142152 900-5M-25 142136 1000-5M-25 142137 1150-5M-25 142138 1300-5M-25 142139 1450-5M-25 142140 1600-5M-25 142141 1720-5M-25 142142 2100-5M-25 142143

Wgt. 0.15 0.15 0.17 0.18 0.19 0.20 0.23 0.26 0.29 0.34 0.36 0.39 0.47

Wt. 0.19 0.20 0.23 0.25 0.27 0.30 0.33 0.35 0.37 0.39 0.40 0.43 0.45 0.47 0.48 0.50 0.51 0.53 0.60 0.62 0.65 0.67 0.73 0.75 0.83 0.90 1.00 1.09 1.17 1.27 1.37 1.51 1.84

50MM Wide Description Part No. 384-8M-50 146466 480-8M-50 146467 560-8M-50 146468 600-8M-50 146469 640-8M-50 146470 720-8M-50 146471 800-8M-50 146472 840-8M-50 146473 880-8M-50 146474 920-8M-50 146475 960-8M-50 146476 1040-8M-50 146477 1064-8M-50 146478 1120-8M-50 146479 1160-8M-50 146480 1200-8M-50 146481 1224-8M-50 146482 1280-8M-50 146483 1440-8M-50 146484 1512-8M-50 146485 1584-8M-50 146486 1600-8M-50 146487 1760-8M-50 146488 1800-8M-50 146489 2000-8M-50 146490 2200-8M-50 146491 2400-8M-50 146492 2600-8M-50 146493 2800-8M-50 146494 3040-8M-50 146495 3280-8M-50 146496 3600-8M-50 146497 4400-8M-50 146498

Wt. 0.33 0.34 0.39 0.42 0.45 0.50 0.56 0.59 0.61 0.64 0.67 0.74 0.76 0.78 0.8 0.84 0.87 0.89 1.01 1.05 1.09 1.11 1.23 1.25 1.39 1.50 1.67 1.81 1.95 2.00 2.29 2.51 3.07

85MM Wide Description Part No. 384-8M-85 146499 480-8M-85 146500 560-8M-85 146501 600-8M-85 146502 640-8M-85 146503 720-8M-85 146504 800-8M-85 146505 840-8M-85 146505 880-8M-85 146507 920-8M-85 146508 960-8M-85 146509 1040-8M-85 146510 1064-8M-85 146511 1120-8M-85 146512 1160-8M-85 146513 1200-8M-85 146514 1224-8M-85 146515 1280-8M-85 146516 1440-8M-85 146517 1512-8M-85 146518 1584-8M-85 146519 1600-8M-85 146520 1760-8M-85 146521 1800-8M-85 146522 2000-8M-85 146523 2200-8M-85 146524 2400-8M-85 146525 2600-8M-85 146526 2800-8M-85 146527 3040-8M-85 146528 3280-8M-85 146529 3600-8M-85 146530 4400-8M-85 146531

Wt. 0.55 0.57 0.66 0.71 0.76 0.85 0.95 1.00 1.04 1.09 1.14 1.23 1.27 1.33 1.28 1.42 1.47 1.52 1.71 1.79 1.82 1.90 2.08 2.13 2.37 2.55 2.84 3.09 3.32 3.62 3.89 4.27 5.22

8 MM Pitch HT200 Belts 20MM Wide Description Part No. 384-8M-20 146400 480-8M-20 146401 560-8M-20 146402 600-8M-20 146403 640-8M-20 146404 720-8M-20 146405 800-8M-20 146406 840-8M-20 146407 880-8M-20 146408 920-8M-20 146409 960-8M-20 146410 1040-8M-20 146411 1064-8M-20 146412 1120-8M-20 146413 1160-8M-20 146414 1200-8M-20 146415 1224-8M-20 146416 1280-8M-20 146417 1440-8M-20 146418 1512-8M-20 146419 1584-8M-20 146420 1600-8M-20 146421 1760-8M-20 146422 1800-8M-20 146423 2000-8M-20 146424 2200-8M-20 146425 2400-8M-20 146426 2600-8M-20 146427 2800-8M-20 146428 3048-8M-20 146429 3280-8M-20 146430 3600-8M-20 146431 4400-8M-20 146432 FEATURES/BENEFITS PAGES PT11-2

Wt. 0.12 0.13 0.16 0.17 0.18 0.20 0.22 0.23 0.25 0.26 0.27 0.29 0.30 0.31 0.32 0.34 0.35 0.36 0.40 0.42 0.43 0.45 0.49 0.50 0.56 0.60 0.67 0.79 0.80 0.85 0.92 1.01 1.23

30MM Wide Description Part No. 384-8M-30 146433 480-8M-30 146434 560-8M-30 146435 600-8M-30 146436 640-8M-30 146437 720-8M-30 146438 800-8M-30 146439 840-8M-30 146440 880-8M-30 146441 920-8M-30 146442 960-8M-30 146443 1040-8M-30 146444 1064-8M-30 146445 1120-8M-30 146446 1160-8M-30 146447 1200-8M-30 146448 1224-8M-30 146449 1280-8M-30 146450 1440-8M-30 146451 1512-8M-30 146452 1584-8M-30 146453 1600-8M-30 146454 1760-8M-30 146455 1800-8M-30 146456 2000-8M-30 146457 2200-8M-30 146458 2400-8M-30 146459 2600-8M-30 146460 2800-8M-30 146461 3040-8M-30 146462 3280-8M-30 146463 3600-8M-30 146464 4400-8M-30 146465

SPECIFICATIONS: SPROCKETS PAGES PT11-4

SELECTION PAGES PT11-19

PT11-17

ENGINEERING/TECHNICAL PAGES PT11-64

DYNA-SYNC HT Synchrous Belts

1120 — 8M — 30

• 200% Rating of HTD Belts • For Use on TAPER-LOCK HT Sprockets Note: Belt length is in millimeters. To convert to inches, divide by 25.4. Example: 2600-8M-30 belt size 2600 ÷25.4 = 102.36 inches belt length

Sprockets

BELT NOMENCLATURE

Conveyor Components

DODGE HT200 Belts

Engineering

SPECIFICATION


DYNA-SYNC

SPECIFICATION DODGE HT200 Belts • 200% Rating of HTD Belts • For Use on TAPER-LOCK HT Sprockets 1120 — 8M — 30 Note: Belt length is in millimeters. Tooth To convert to inches, divide by 25.4 Pitch Belt Pitch Length Width Example: 2600-8M-30 belt size Spacing (mm) (mm) 2600 ÷25.4 = 102.36 inches belt length (mm) BELT NOMENCLATURE

HT Synchrous Belts

14 MM Pitch HT200 Belts

Sprockets

40MM Wide Description Part No. 966-14M-40 146532 1190-14M-40 146533 1400-14M-40 146534 1610-14M-40 146535 1778-14M-40 146536 1890-14M-40 146537 2100-14M-40 146538 2310-14M-40 146539 2450-14M-40 146540 2590-14M-40 146541 2800-14M-40 146542 3150-14M-40 146543 3360-14M-40 146544 3500-14M-40 146545 3850-14M-40 146546 4326-14M-40 146547 4578-14M-40 146548 4956-14M-40 146549 5320-14M-40 146550 5740-14M-40 146551 6160-14M-40 146552 6860-14M-40 146553

Wt. 0.84 1.03 1.21 1.40 1.54 1.64 1.82 2.00 2.13 2.25 2.43 2.73 2.91 3.03 3.33 3.74 3.96 4.29 4.61 4.97 5.33 5.94

55MM Wide Description Part No. 966-14M-55 146554 1190-14M-55 146555 1400-14M-55 146556 1610-14M-55 146557 1778-14M-55 146558 1890-14M-55 146559 2100-14M-55 146560 2310-14M-55 146561 2450-14M-55 146562 2590-14M-55 146563 2800-14M-55 146564 3150-14M-55 146565 3360-14M-55 146566 3500-14M-55 146567 3850-14M-55 146568 4326-14M-55 146569 4578-14M-55 146570 4956-14M-55 146571 5320-14M-55 146572 5740-14M-55 146573 6160-14M-55 146574 6860-14M-55 146575

Wt. 1.15 1.42 1.67 1.92 2.13 2.26 2.51 2.76 2.93 3.10 3.34 3.77 4.02 4.19 4.60 5.17 5.48 5.90 6.33 6.83 7.33 8.16

85MM Wide Description Part No. 966-14M-85 146576 1190-14M-85 146577 1400-14M-85 146578 1610-14M-85 146579 1778-14M-85 146580 1890-14M-85 146581 2100-14M-85 146582 2310-14M-85 146583 2450-14M-85 146584 2590-14M-85 146585 2800-14M-85 146586 3150-14M-85 146587 3360-14M-85 146588 3500-14M-85 146589 3850-14M-85 146590 4326-14M-85 146591 4578-14M-85 146592 4956-14M-85 146593 5320-14M-85 146594 5740-14M-85 146595 6160-14M-85 146596 6860-14M-85 146597

Wt. 1.78 2.20 2.58 2.97 3.28 3.49 3.88 4.26 4.52 4.78 5.17 5.82 6.20 6.46 7.10 8.00 8.45 9.11 9.28 10.55 11.32 12.61

115MM Wide Description Part No. 966-14M-115 146598 1190-14M-115 146599 1400-14M-115 146600 1610-14M-115 146601 1778-14M-115 146602 1890-14M-115 146603 2100-14M-115 146604 2310-14M-115 146605 2450-14M-115 146606 2590-14M-115 146607 2800-14M-115 146608 3150-14M-115 146609 3360-14M-115 146610 3500-14M-115 146611 3850-14M-115 146612 4326-14M-115 146613 4578-14M-115 146614 4956-14M-115 146615 5320-14M-115 146616 5740-14M-115 146617 6160-14M-115 146618 6860-14M-115 146619

Wt. 2.41 2.98 3.50 4.02 4.45 4.73 5.25 5.77 6.13 6.47 7.00 7.87 8.39 8.75 9.62 10.80 11.42 12.33 13.24 14.29 15.34 17.08

WT. 9.0 11.0 16.0 18.0 20.0 21.5 23.0 24.0 25.0 26.0 27.0 28.0 29.0 30.0 31.0

230MM Wide Size Part No. 2000-20M-230 142318 2500-20M-230 142319 3400-20M-230 142320 3800-20M-230 142321 4200-20M-230 142322 4600-20M-230 142323 5000-20M-230 142324 5200-20M-230 142325 5400-20M-230 142326 5600-20M-230 142327 5800-20M-230 142328 6000-20M-230 142329 8200-20M-230 142330 6400-20M-230 142331 6600-20M-230 142332

WT. 12.0 15.0 22.0 24.5 27.0 29.5 32.0 33.0 34.0 35.5 37.0 38.0 39.0 40.5 42.0

290MM Wide Size Part No. 2000-20M-290 142333 2500-20M-290 142334 3400-20M-290 142335 3800-20M-290 142336 4200-20M-290 142337 4600-20M-290 142338 5000-20M-290 142339 5200-20M-290 142340 5400-20M-290 142341 5600-20M-290 142342 5800-20M-290 142343 6000-20M-290 142344 6200-20M-290 142345 6400-20M-290 142346 6600-20M-290 142347

WT. 16.0 20.0 27.0 30.5 34.0 37.0 40.0 41.5 43.0 44.5 46.0 48.0 50.0 51 5 53.0

170MM Wide Description Part No. 966-14M-170 146620 1190-14M-170 146621 1400-14M-170 146622 1610-14M-170 146623 1778-14M-170 146624 1890-14M-170 146625 2100-14M-170 146626 2310-14M-170 146627 2450-14M-170 146628 2590-14M-170 146629 2800-14M-170 146630 3150-14M-170 146631 3360-14M-170 146631 3500-14M-170 146633 3850-14M-170 146634 4326-14M-170 146635 4578-14M-170 146636 4956-14M-170 146637 5320-14M-170 146638 5740-14M-170 146639 6160-14M-170 146640 6860-14M-170 146641

Wt. 3.56 4.39 5.16 5.95 6.56 6.97 7.75 8.53 9.04 9.55 10.33 11.62 12.39 12.90 14.20 15.96 16.90 18.23 19.57 25.00 22.67 25.25

20MM Pitch HTD Belts Conveyor Components Engineering

115MM Wide Size Part No. 2000-20M-115 142288 2500-20M-115 142289 3400-20M-115 142290 3800-20M-115 142291 4200-20M-115 142292 4600-20M-115 142293 5000-20M-115 142294 5200-20M-115 142295 5400-20M-115 142296 5600-20M-115 142297 5800-20M-115 142298 6000-20M-115 142299 6200-20M-115 142300 6400-20M-115 142301 6600-20M-115 142302

WT. 6.0 8.0 11.0 12.0 13.0 14.5 16.0 16.5 17.0 17.5 18 0 19.0 20 0 21.0 22 0

FEATURES/BENEFITS PAGES PT11-2

170MM Wide Size Part No. 2000-20M-170 142303 2500-20M-170 142304 3400-20M-170 142305 3800-20M-170 142306 4200-20M-170 142307 4600-20M-170 142308 5000-20M-170 142309 5200-20M-170 142310 5400-20M-170 142311 5600-20M-170 142312 5800-20M-170 142313 6000-20M-170 142314 6200-20M-170 142315 6400 20M 170 142316 6600-20M-170 142317

SPECIFICATIONS: SPROCKETS PAGES PT11-4

SELECTION PAGES PT11-19

PT11-18

340MM Wide Size Part No. 2000-20M-340 142348 2500-20M-340 142349 3400-20M-340 142350 3800-20M-340 142351 4200-20M-340 142352 4600-20M-340 142353 5000-20M-340 142354 5200-20M-340 142355 5400-20M-340 142356 5600-20M-340 142357 5800-20M-340 142358 6000-20M-340 142359 6200-20M 340 142360 6400-20M-340 142361 6600-20M-340 142362

WT. 19.0 24.0 32.0 35.5 39.0 43.0 47.0 49.0 51.0 52.5 54.0 56.0 58.0 60 0 62.0

ENGINEERING/TECHNICAL PAGES PT11-64


PROCEDURE

Example

1.

Step 1. Required Information: Select an HT200 drive to connect a 15HP APG gearmotor to a package conveyor headshaft. Reducer output is 125 RPM, shaft size is 2”. Headshaft is 2-3/4” and is to run at 70 RPM. Center distance is 19-23”, operation is 14 hrs/day.

5.

6. 7.

8.

9.

FEATURES/BENEFITS PAGES PT11-2

Step 4. Belt Pitch: Referring to page PT11-21, most probable belt pitch for 25.5 Des. HP at 125 RPM is 14MM. Step 5. Select Small Sprocket: Scan 14MM HP Tables. Since there is no 125 RPM line, it will be necessary to interpolate. Start with the 100 RPM line. Observe that a 38 tooth sprocket for a 115MM wide belt gives 22.3 HP. Interpolation for 125 RPM gives 27.5 HP. Other alternatives are also available (see below) Step 6. Drive Ratio: 125 / 70 RPM = 1.79:1 Step 7. Sprocket Selection: Refer to 14MM Ratio/Center Distance tables. For 1.79 ratio, note that there are 5 drive combinations in the 1.78 to 1.80 range. The 38 tooth DriveR and the 68 tooth DriveN combination appears to be good, however we need to account for the belt length correction factor of .95, which gives us a net design HP of 25.7. (Note 20.2 C.D. requires a 1778 length code belt)

Sprockets

4.

Step 3. Design HP: 1.7 x 15 = 25.5 HP.

Step 8. Finalize Selection: Select the 38 to 68 tooth combination with a 1778 length code belt for 20.2” C.D. From step 7, rated HP is 25.7 Alternatively, select the 40 to 72 tooth combination with a 1778 length code belt for 19.4 C.D. With interpolation and correction, the rated HP is 27.22. Step 9. Specify Drive: Original Selection: DriveR Sprocket: P38-14M-115-3020, P/N 114520 Bushing. 3020 x 2”, P/N 117118 DriveN Sprocket. P68-14M-115-4545, P/N 114528 Bushing. 4545 x 2-3/4”, P/N 117426 Belt: 1778-14M-115 HT200 Belt, P/N 146602 Shaft capacity is verified by availability of bore sizes.

Conveyor Components

3.

Step 2: Service Factor: Package Conveyor requires 1.4 basic Service Factor. Add 0.3 for slow speed drive application (step 2 at left). Net S.F. = 1.7

Alternative Selection: DriveR Sprocket: P40-14M-115-3020, P/N 114475 Bushing. 3020 x 2”, P/N 117118 DriveN Sprocket. P68-14M-115-4545, P/N 114529 Bushing. 4545 x 2-3/4”, P/N 117426 Belt: 1778-14M-115 HT200 Belt, P/N 146602 Shaft capacity is verified by availability of bore sizes.

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-19

ENGINEERING/TECHNICAL PAGES PT11- 4

Engineering

2.

Obtain required information: • Motor name plate HP • Motor or DriveR RPM and Shaft size • DriveN Machine RPM and Shaft size • Approximate center distance • Service factor information Determine Service Factor: (Page PT11-20) • Determine type of Driven Machine from Table 1 • Choose Basic Service Factor in appropriate column of the following S.F. Table • Add additional service factor for slow speed drives, idlers or speed up drives were applicable Calculate Design Horsepower: • Multiply Motor HP or normal running HP times Service Factor from Step 2 • Note: Recommended Min. Sprocket Diameter, if applicable, from NEMA table on page PT11-21. Determine Belt Pitch: (Page PT11-21) • Choose belt pitch based upon Design HP and RPM of faster shaft Select Smaller Sprocket: • Look at Basic HP rating tables of belt Pitch selected in Step 4 • Scan HP rating at RPM of faster shaft. (Pg. PT11-22 thru PT11-26) • Find sprocket size(s) that have HP rating at or above Design HP Calculate Drive Ratio: • Divide Fast Shaft RPM by Slow Shaft RPM Select Sprockets and Belt: • Refer to "Ratio/Center Distance" Tables for Belt pitch chosen in Step 4. (Pg. PT11-35 - PT11-63) • Trace down left hand column to approximate ratio calculated in Step 6 • Choose drive that has small sprocket at or above the number of teeth determined in Step 5 • On this same line, trace to the right until the number closest to the required center distance is reached • Trace to the top of this column and note the belt size that gives this center distance • Also note the "Belt Length Correction Factor" at the top or bottom of this same column Finalize Selection: • Multiply "Belt Length Correction Factor" times indicated rating obtained from HP table • Verify that Design HP is equal to or less than this corrected HP value • Note: If Correction Factor is greater than 1.0 corrected HP may allow selection of smaller less expensive drive Specify Drive: • DriveR Sprocket and Bushing • DriveN Sprocket and Bushing • Belt • Verify that bushing bore has capacity for shaft size

DYNA-SYNC

HT200/HTD Drive Selection Procedure

HT Synchrous Belts

SELECTION


DYNA-SYNC

SELECTION Service Factors Table 1 DriveN Machine The driveN machines listed below are representative samples only. Select a driveN machine whose load characteristics most closely approximate those of the machine being considered.

HT Synchrous Belts

DriveR AC Motors: High Torque, High Slip, RepulsionInduction, Single Phase, Series Wound, Slip Ring DC Motors: Series Wound, Compound Wound Servo Motors Engines: Single Cylinder Internal Combustion Line Shafts Clutches Continuous Intermittent Normal Continuous Service Service Service Service Up to 8 hours Daily or 8 - 16 hours 16 - 24 hours 16 - 24 hours Seasonal Daily Daily Daily

AC Motors: Normal Torque, Squirrel Cage, Synchronous, Split Phase, Inverter Controlled DC Motors: Shunt Wound Stepper Motors Engines: Multiple Cylinder Internal Combustion

Sprockets Conveyor Components

Intermittent Service Up to 8 hours Daily or Seasonal

8 - 16 hours Daily

1.0

1.2

1.4

1.2

1.4

1.6

1.1

1.3

1.5

1.3

1.5

1.7

1.2

1.4

1.6

1.6

1.8

2.0

1.3

1.5

1.7

1.6

1.8

2.0

1.4

1.6

1.8

1.8

2.0

2.2

1.5

1.7

1.9

1.9

2.1

2.3

1.6

1.8

2.0

2.0

2.2

2.4

1.7

1.9

2.1

2.1

2.3

2.5

Display, Dispensing Equipment, Instrumentation, Measuring Equipment, Medical Equipment, Office, Projection Equipment Appliances, Sweepers, Sewing Machines Screens, Oven Screens, Drum, Conical Woodworking Equipment (Light): Band Saws, Drills, Lathes Agitators for Liquids, Conveyors: Belt, Light Package, Drill Press, Lathes, Saws, Laundry Machinery, Wood Working Equipment (Heavy): Circular Saws, Jointers, Planers Agitators for Semi-Liquids, Compressor: Centrifugal, Conveyor Belt: Ore, Coal, Sand Dough Mixers, Line Shafts, Machine Tools: Grinder, Shaper, Boring Mill, Milling Machines, Paper Machinery (except Pulpers): Presses, Punches, Shears, Printing Machinery, Pumps: Centrifugal, Gear, Screens: Revolving, Vibratory Brick Machinery (except Pug Mills) Conveyor: Apron, Pan, Bucket, Elevator, Extractors, Washers, Fans, Centrifugal Blowers, Generators & Exciters, Hoists, Rubber Calender, Mills, Extruders Centrifuges, Screw Conveyors Hammer Mill, Paper Pulpers, Textile Machinery Blowers: Positive Displacement, Mine Fans, Pulverizers Compressors: Reciprocating, Crushers: Gyratory, Jaw, Roll, Mills: Ball, Rod, Pebble, etc., Pumps: Reciprocating Saw Mill Equipment

Normal Service

These service factors are adequate for most belt drive applications. Note that service factors cannot be substituted for good engineering judgment. Service factors may be adjusted based upon an understanding of the severity of actual drive operation conditions.

Additional Service Factors Low Speed Drives

Speed-up Drives

Engineering

8mm, 14,, & 20mm Belts Only Smaller Sprocket Speed Up to 200 rpm Add 0.3 201 to 400 rpm Add 0.2 401 to 600 rpm Add 0.1 Each Idler

Add 0.2

For speed up drives, add the basic service factor to the additional factor given below. Speed-up Ratio Range 1 to 1.24 1.25 to 1.74 1.75 to 2.49

Additional Factor none .10 .20

Speed-up Ratio Range 2.50 to 3.49 3.50 & over

Additional Factor .30 .40

Unusual Conditions Additional service factors are required for unusual conditions such as load reversal, heavy shock, plugged motor stop, electric brake. Consult factory for recommendation.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-20

ENGINEERING/TECHNICAL PAGES PT11- 4


Belt Pitch Selection Guide 10000

DYNA-SYNC

SELECTION

7000

5mm HT200

Synchronous belt drive noise increases as a function of Design Horsepower and operating RPM. This is indicated on the chart at the left. Provisions should be made to design drive guards for sound absorption accordingly.

1750 1160 870 600 400

8mm HT200 200

20mm HTD

14mm HT200

100 80 60 40

HT Synchrous Belts

5000

3450

20

10 0.1

0.2

0.4

0.6 0.8 1.0

2.0

4.0

6.0 8.0 10

20

40

60 80 100

200

400

600

1000

Design Horsepower

FEATURES/BENEFITS PAGES PT11-2

870

1160

1750

3450

2.25 2.25 2.75 2.75 3.38 3.38 4.0 4.0 4.63 4.63 5.25 5.25 5.87 5.88 7.25 7.25 8.5 8.5 8.5 11.63 11.63 11.63 -

2.25 2.25 2.75 2.75 3.38 3.38 4.0 4.0 4.63 4.63 5.25 5.25 5.88 5.88 7.25 7.25 8.5 8.5 8.5 11.63 11.63 11.63 11.63 -

2.25 2.25 2.25 2.75 2.75 3.38 3.38 4.0 4.0 4.63 4.63 5.25 5.25 5.88 5.88 7.25 7.25 8.5 11.63 9.38 11.63 11.63 11.63

2.25 2.25 2.25 2.75 2.75 3.38 3.38 4.0 4.0 -

SPECIFICATIONS SPROC ETS PAGES PT11-4

NOTE: For a given motor horsepower and speed, the total belt pull is related to the motor sprocket size. As this size decreases, the total belt pull increases. Therefore, to limit the resultant load on motor shaft and bearings, NEMA lists minimum sprocket sizes for the various motors. The sprocket on the motor (DriveR Sprocket) should be at least this large.

SPECIFICATIONS BELTS PAGES PT11-1

PT11-21

Conveyor Components

Maximum Face Width

Engineering

Motor Min. Sprocket Dia. (in.) Horse 870 1160 1750 3450 power 1/2 2.0 3/4 2.16 2.0 1 2.16 2.16 2.0 1-1/2 2.16 2.16 2.16 2.0 2 2.7 2.16 2.16 2.16 3 2.7 2.7 2.16 2.16 5 3.42 2.7 2.7 2.16 7-1/2 4.0 3.42 2.7 2.7 10 4.0 4.0 3.42 2.7 15 4.7 4.0 4.0 3.42 20 5.4 4.7 4.0 4.0 25 6.12 5.4 4.0 4.0 30 6.12 6.12 4.7 40 7.4 6.12 5.4 50 7.6 7.4 6.12 60 9.0 8.1 6.7 75 8.6 9.0 7.8 100 10.8 9.0 7.8 125 11.3 10.8 9.5 150 11.88 11.88 9.5 200 11.88 11.88 11.88 250 13.5 11.88 11.88 300 11.88 350 11.88 400 12.69 -

Sprockets

Recommended Minimum Sprocket Diameters & Face Width Synchronous Belt Drives Used On General Purpose Electric Motors

ENGINEERING/TECHNICAL PAGES PT11- 4


DYNA-SYNC

SELECTION HT200 Basic Horsepower Rating NOTE: Multiply rating by Belt Length Correction Factor from Ratio/Center Distance Tables 30 3.01 0.10 0.20 0.37 0.55 0.88 1.67 2.44 3.18 3.90 4.62 5.32 6.01 6.49 7.38 8.45 8.71 10.0 11.3 12.3 13.9 16.3 18.7 21.1 22.5 25.6 28.4 31.0 33.6

Rated Horsepower for Small Sprocket (Number of Teeth and Pitch Diameter, Inches) 32 34 36 38 40 44 3.21 3.41 3.61 3.81 4.01 4.44 0.11 0.12 0.13 0.14 0.15 0.16 0.21 0.23 0.25 0.27 0.28 0.32 0.41 0.44 0.48 0.51 0.54 0.61 0.60 0.65 0.69 0.74 0.79 0.89 0.96 1.04 1.12 1.20 1.28 1.44 1.83 1.98 2.14 2.29 2.45 2.75 2.66 2.89 3.12 3.35 3.57 4.02 3.48 3.78 4.07 4.37 4.67 5.26 4.27 4.64 5.01 5.38 5.74 6.47 5.06 5.50 5.93 6.37 6.80 7.67 5.83 6.34 6.84 7.35 7.85 8.85 6.59 7.17 7.74 8.31 8.88 10.0 7.12 7.74 8.36 8.98 9.60 10.8 8.09 8.80 9.50 10.2 10.9 12.3 9.26 10.1 10.9 11.7 12.5 14.1 9.56 10.4 11.2 12.1 12.9 14.6 11.0 12.0 12.9 13.9 14.9 16.8 12.4 13.5 14.6 15.7 16.8 19.0 13.5 14.7 15.9 17.1 18.2 20.6 15.2 16.6 17.9 19.3 20.6 23.2 17.9 19.5 21.1 22.7 24.3 27.4 20.6 22.4 24.2 26.0 27.8 31.4 23.2 25.2 27.3 29.3 31.3 35.3 24.8 27.0 29.1 31.3 33.5 37.7 28.2 30.7 33.1 35.6 38.0 42.8 31.1 33.9 36.6 39.3 42.0 47.2 34.0 37.0 40.0 42.9 45.7 51.3 36.8 40.0 43.2 46.3 49.3 55.3

30 3.01 0.16 0.31 0.59 0.86 1.38 2.63 3.82 4.99 6.13 7.25 8.35 9.44 10.2 11.6 13.3 13.7 15.7 17.8 19.3 21.8 25.6 29.4 33.1 35.4 40.3 44.5 48.7 52.7

Rated Horsepower for Small Sprocket (Number of Teeth and Pitch Diameter, Inches) 32 34 36 38 40 44 3.21 3.41 3.61 3.81 4.01 4.41 0.17 0.19 0.20 0.22 0.23 0.26 0.33 0.36 0.39 0.42 0.44 0.50 0.64 0.69 0.75 0.80 0.85 0.96 0.94 1.01 1.09 1.17 1.25 1.40 1.51 1.63 1.76 1.89 2.01 2.26 2.87 3.12 3.36 3.60 3.84 4.33 4.18 4.54 4.90 5.25 5.61 6.32 5.46 5.93 6.40 6.87 7.33 8.26 6.71 7.29 7.87 8.45 9.02 10.2 7.94 8.63 9.31 10.0 10.7 12.0 9.15 9.95 10.7 11.5 12.3 13.9 10.3 11.2 12.1 13.0 13.9 15.7 11.2 12.2 13.1 14.1 15.1 17.0 12.7 13.8 14.9 16.0 17.1 19.3 14.5 15.8 17.1 18.4 19.6 22.2 15.0 16.3 17.6 19.0 20.3 22.9 17.3 18.8 20.3 21.8 23.3 26.3 19.5 21.2 23.0 24.7 26.4 29.8 21.2 23.0 24.9 26.8 28.6 32.3 23.9 26.0 28.1 30.2 32.3 36.5 28.1 30.7 33.1 35.6 38.1 43.0 32.3 35.2 38.0 40.9 43.7 49.3 36.4 39.6 42.8 46.0 49.2 55.4 38.9 42.3 45.8 49.2 52.5 59.2 44.2 48.1 52.0 55.9 59.7 67.1 48.9 53.2 57.5 61.7 65.9 74.0 53.4 58.1 62.8 67.3 71.8 80.6 57.8 62.9 67.8 72.7 77.5 86.8

8M-20 RPM SMALL SHAFT

HT Synchrous Belts Sprockets

10 20 40 60 100 200 300 400 500 600 700 800 870 1000 1160 1200 1400 1600 1750 2000 2400 2800 3200 3450 4000 4500 5000 5500

22 2.21 0.07 0.12 0.24 0.35 0.55 1.04 1.51 1.96 2.40 2.83 3.26 3.68 3.96 4.49 5.13 5.29 6.07 6.84 7.41 8.35 9.81 11.2 12.6 13.5 15.3 16.9 18.5 20.0

24 2.41 0.07 0.14 0.27 0.40 0.63 1.20 1.74 2.27 2.78 3.28 3.78 4.26 4.60 5.22 5.97 6.15 7.07 7.97 8.64 9.73 11.4 13.1 14.8 15.8 17.9 19.8 21.7 23.5

26 2.61 0.08 0.16 0.31 0.45 0.72 1.36 1.97 2.57 3.16 3.73 4.29 4.85 5.23 5.94 6.80 7.01 8.06 9.09 9.86 11.1 13.1 15.0 16.9 18.0 20.5 22.7 24.8 26.9

28 2.81 0.09 0.18 0.34 0.50 0.80 1.52 2.20 2.87 3.53 4.17 4.80 5.43 5.86 6.66 7.62 7.86 9.04 10.2 11.1 12.5 14.7 16.9 19.0 20.3 23.1 25.5 27.9 30.2

8M-30 RPM SMALL SHAFT

Conveyor Components Engineering

10 20 40 60 100 200 300 400 500 600 700 800 870 1000 1160 1200 1400 1600 1750 2000 2400 2800 3200 3450 4000 4500 5000 5500

22 2.21 0.10 0.20 0.37 0.54 0.87 1.64 2.37 3.08 3.77 4.45 5.11 5.77 6.22 7.05 8.06 8.31 9.54 10.7 11.6 13.1 15.4 17.6 19.8 21.1 24.0 26.6 29.0 31.4

24 2.41 0.12 0.22 0.43 0.62 1.00 1.89 2.74 3.56 4.36 5.15 5.93 6.69 7.22 8.19 9.37 9.66 11.1 12.5 13.6 15.3 18.0 20.6 23.2 24.7 28.1 31.1 34.0 36.8

26 2.61 0.13 0.25 0.48 0.70 1.12 2.13 3.10 4.04 4.95 5.85 6.74 7.61 8.22 9.33 10.7 11.0 12.7 14.3 15.5 17.5 20.5 23.6 26.5 28.3 32.2 35.6 39.0 42.2

28 2.81 0.15 0.28 0.53 0.78 1.25 2.38 3.46 4.51 5.54 6.55 7.54 8.52 9.20 10.5 12.0 12.3 14.2 16.0 17.4 19.6 23.1 26.5 29.8 31.9 36.2 40.1 43.8 47.5

48 4.81 0.18 0.35 0.68 0.99 1.60 3.06 4.47 5.85 7.20 8.53 9.84 11.1 12.0 13.7 15.7 16.2 18.7 21.1 22.9 25.8 30.5 34.9 39.2 41.9 47.4 52.2 56.7

48 4.81 0.29 0.55 1.06 1.55 2.51 4.80 7.02 9.18 11.3 13.4 15.5 17.5 18.9 21.5 24.7 25.4 29.3 33.1 36.0 40.6 47.8 54.8 61.6 65.7 74.5 82.0 89.1

56 5.61 0.22 0.42 0.81 1.18 1.91 3.67 5.36 7.02 8.64 10.2 11.8 13.4 14.5 16.5 18.9 19.5 22.4 25.3 27.5 31.0 36.5 41.8 46.9 50.0 56.4

56 5.61 0.34 0.66 1.27 1.86 3.00 5.76 8.42 11.0 13.6 16.1 18.6 21.0 22.7 25.8 29.6 30.6 35.2 39.8 43.2 48.7 57.3 65.6 73.6 78.4 88.5

64 6.42 0.25 0.49 0.94 1.38 2.23 4.27 6.24 8.17 10.1 11.9 13.8 15.6 16.9 19.2 22.0 22.7 26.1 29.5 32.0 36.1 42.4 48.5 54.2 57.7

64 6.42 0.40 0.76 1.47 2.16 3.49 6.70 9.80 12.8 15.8 18.7 21.6 24.5 26.5 30.1 34.5 35.6 41.0 46.3 50.3 56.7 66.6 76.1 85.2 90.6

72 7.22 0.29 0.55 1.07 1.57 2.54 4.87 7.12 9.32 11.5 13.6 15.7 17.8 19.2 21.9 25.1 25.9 29.8 33.6 36.5 41.1 48.2 54.9 61.3 65.1

80 8.02 0.32 0.62 1.20 1.76 2.84 5.46 7.99 10.5 12.9 15.3 17.6 20.0 21.6 24.5 28.1 29.0 33.4 37.7 40.8 45.9 53.8 61.2

72 7.22 0.45 0.87 1.68 2.46 3.98 7.64 11.2 14.6 18.0 21.4 24.7 27.9 30.2 34.3 39.4 40.6 46.8 52.8 57.2 64.5 75.6 86.2 96.2 102.2

80 8.02 0.51 0.98 1.88 2.76 4.47 8.58 12.5 16.4 20.2 24.0 27.7 31.4 33.9 38.5 44.2 45.6 52.4 59.1 64.1 72.1 84.4 96.0

Operation in shaded area will result in a reduction of belt life. FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-22

ENGINEERING/TECHNICAL PAGES PT11- 4


HT200 Basic Horsepower Rating NOTE: Multiply rating by Belt Length Correction Factor from Ratio/Center Distance Tables 24 2.41 0.20 0.39 0.74 1.08 1.73 3.28 4.76 6.19 7.59 8.96 10.3 11.6 12.6 14.2 16.3 16.8 19.3 21.8 23.6 26.6 31.3 35.8 40.3 43.0 48.9 54.1 59.1 64.0

26 2.61 0.23 0.44 0.84 1.22 1.96 3.71 5.39 7.02 8.61 10.2 11.7 13.2 14.3 16.2 18.6 19.1 22.0 24.8 26.9 30.3 35.7 41.0 46.1 49.2 56.0 62.0 67.8 73.4

28 2.81 0.25 0.49 0.93 1.35 2.18 4.14 6.02 7.85 9.63 11.4 13.1 14.8 16.0 18.2 20.8 21.5 24.7 27.9 30.2 34.1 40.2 46.1 51.9 55.4 63.0 69.7 76.2 82.5

30 3.01 0.48 0.93 1.78 2.59 4.17 7.95 11.6 15.1 18.5 21.9 25.3 28.6 30.8 35.0 40.1 41.4 47.6 53.8 58.3 65.8 77.6 89.0 100.2 107.0 121.8 134.7 147.3 159.4

Rated Horsepower for Small Sprocket (Number of Teeth and Pitch Diameter, Inches) 32 34 36 38 40 44 3.21 3.41 3.61 3.81 4.01 4.41 0.53 0.57 0.61 0.65 0.70 0.78 1.01 1.09 1.18 1.26 1.34 1.50 1.94 2.10 2.26 2.42 2.57 2.89 2.83 3.07 3.30 3.53 3.77 4.23 4.56 4.94 5.32 5.70 6.08 6.84 8.69 9.43 10.2 10.9 11.6 13.1 12.7 13.7 14.8 15.9 17.0 19.1 16.5 17.9 19.4 20.8 22.2 25.0 20.3 22.1 23.8 25.6 27.3 30.8 24.0 26.1 28.2 30.3 32.3 36.4 27.7 30.1 32.5 34.9 37.3 42.0 31.3 34.0 36.8 39.5 42.2 47.6 33.8 36.8 39.7 42.7 45.6 51.4 38.4 41.8 45.1 48.5 51.8 58.5 44.0 47.9 51.7 55.6 59.4 67.0 45.4 49.4 53.4 57.4 61.3 69.2 52.3 56.9 61.5 66.1 70.6 79.7 59.0 64.3 69.4 74.6 79.8 90.1 64.0 69.7 75.4 81.0 86.6 97.7 72.3 78.7 85.1 91.4 97.8 110.3 85.2 92.8 100.3 107.8 115.2 130.0 97.8 106.5 115.1 123.7 132.3 149.2 110.0 119.9 129.6 139.3 148.8 167.7 117.6 128.1 138.4 148.7 158.9 179.1 133.7 145.6 157.4 169.0 180.5 203.1 147.9 161.0 173.9 186.7 199.3 224.0 161.7 175.9 189.9 203.7 217.3 243.8 174.9 190.2 205.2 220.0 234.4 262.5

8M-85 RPM SMALL SHAFT

10 20 40 60 100 200 300 400 500 600 700 800 870 1000 1160 1200 1400 1600 1750 2000 2400 2800 3200 3450 4000 4500 5000 5500

22 2.21 0.31 0.59 1.13 1.64 2.63 4.96 7.17 9.32 11.4 13.5 15.5 17.5 18.8 21.3 24.4 25.1 28.9 32.5 35.2 39.6 46.6 53.3 59.9 64.0 72.7 80.3 87.8 95.0

24 2.41 0.35 0.68 1.29 1.88 3.01 5.71 8.28 10.8 13.2 15.6 17.9 20.2 21.8 24.8 28.3 29.2 33.6 37.9 41.0 46.2 54.4 62.3 70.1 74.9 85.1 94.1 102.9 111.4

26 2.61 0.40 0.76 1.45 2.12 3.40 6.46 9.38 12.2 15.0 17.7 20.4 23.0 24.9 28.2 32.3 33.3 38.3 43.2 46.8 52.8 62.2 71.3 80.2 85.7 97.5 107.8 117.9 127.7

28 2.81 0.44 0.84 1.61 2.36 3.79 7.20 10.5 13.7 16.8 19.8 22.8 25.8 27.8 31.6 36.2 37.3 43.0 48.5 52.6 59.3 69.9 80.2 90.2 96.4 109.6 121.3 132.7 143.6

48 4.81 0.50 0.96 1.84 2.70 4.36 8.35 12.2 16.0 19.7 23.3 26.9 30.4 32.9 37.4 42.9 44.2 51.0 57.6 62.5 70.6 83.1 95.3 107.1 114.3 129.5 142.5 154.9

48 4.81 0.87 1.67 3.21 4.70 7.59 14.5 21.2 27.8 34.2 40.5 46.8 52.9 57.2 65.1 74.6 77.0 88.7 100.2 108.8 122.8 144.6 165.9 186.4 198.8 225.3 248.0 269.4

56 5.61 0.59 1.14 2.20 3.23 5.22 10.0 14.6 19.2 23.6 28.0 32.3 36.5 39.5 44.9 51.5 53.1 61.2 69.2 75.0 84.7 99.7 114.1 128.0 136.4 154.0

56 5.61 1.03 1.99 3.83 5.62 9.09 17.4 25.5 33.3 41.0 48.6 56.1 63.6 68.7 78.2 89.6 92.5 106.5 120.4 130.6 147.3 173.4 198.5 222.7 237.3 267.9

64 6.42 0.69 1.33 2.56 3.75 6.08 11.7 17.0 22.3 27.5 32.6 37.6 42.6 46.0 52.4 60.0 61.9 71.3 80.6 87.4 98.5 115.8 132.3 148.1 157.5

64 6.42 1.20 2.31 4.46 6.53 10.6 20.3 29.7 38.8 47.8 56.7 65.4 74.1 80.1 91.1 104.5 107.8 124.1 140.2 152.0 171.4 201.4 230.2 257.6 274.1

72 7.22 0.78 1.51 2.92 4.28 6.92 13.3 19.4 25.5 31.4 37.2 42.9 48.6 52.5 59.7 68.5 70.6 81.3 91.8 99.5 112.1 131.5 149.9 167.4 177.7

72 7.22 1.36 2.63 5.07 7.44 12.0 23.1 33.8 44.3 54.6 64.7 74.7 84.5 91.4 103.9 119.1 122.9 141.5 159.7 173.1 195.0 228.8 260.9 291.2 309.1

80 8.02 0.88 1.70 3.27 4.80 7.77 14.9 21.8 28.6 35.2 41.7 48.2 54.5 58.9 67.0 76.8 79.2 91.2 102.9 111.4 125.4 146.8 166.9

Sprockets

10 20 40 60 100 200 300 400 500 600 700 800 870 1000 1160 1200 1400 1600 1750 2000 2400 2800 3200 3450 4000 4500 5000 5500

22 2.21 0.18 0.34 0.65 0.94 1.51 2.85 4.12 5.36 6.56 7.74 8.89 10.0 10.8 12.3 14.0 14.4 16.6 18.7 20.2 22.8 26.8 30.7 34.4 36.8 41.8 46.2 50.5 54.6

80 8.02 1.53 2.95 5.69 8.34 13.5 25.9 38.0 49.7 61.2 72.6 83.8 94.9 102.5 116.6 133.6 137.8 158.6 179.0 193.9 218.2 255.4 290.5

Operation in shaded area will result in a reduction of belt life. FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-23

ENGINEERING/TECHNICAL PAGES PT11- 4

Conveyor Components

RPM SMALL SHAFT

Engineering

30 3.01 0.28 0.53 1.02 1.49 2.40 4.57 6.65 8.67 10.7 12.6 14.5 16.4 17.7 20.1 23.1 23.8 27.4 30.9 33.5 37.8 44.6 51.2 57.6 61.5 70.0 77.4 84.7 91.6

Rated Horsepower for Small Sprocket (Number of Teeth and Pitch Diameter, Inches) 32 34 36 38 40 44 3.21 3.41 3.61 3.81 4.01 4.44 0.30 0.33 0.35 0.38 0.40 0.45 0.58 0.63 0.68 0.72 0.77 0.86 1.11 1.21 1.30 1.39 1.48 1.66 1.63 1.76 1.90 2.03 2.17 2.43 2.62 2.84 3.06 3.28 3.50 3.93 4.99 5.42 5.84 6.26 6.68 7.52 7.27 7.90 8.52 9.14 9.75 11.0 9.49 10.3 11.1 11.9 12.7 14.4 11.7 12.7 13.7 14.7 15.7 17.7 13.8 15.0 16.2 17.4 18.6 20.9 15.9 17.3 18.7 20.1 21.4 24.2 18.0 19.6 21.1 22.7 24.2 27.3 19.4 21.1 22.8 24.5 26.2 29.5 22.1 24.0 25.9 27.9 29.8 33.6 25.3 27.5 29.7 32.0 34.1 38.5 26.1 28.4 30.7 33.0 35.2 39.8 30.0 32.7 35.3 38.0 40.6 45.8 33.9 36.9 39.9 42.9 45.9 51.8 36.8 40.1 43.3 46.6 49.8 56.2 41.5 45.2 48.9 52.6 56.2 63.4 48.9 53.3 57.6 62.0 66.2 74.7 56.2 61.2 66.2 71.1 76.0 85.7 63.2 68.9 74.5 80.0 85.5 96.4 67.6 73.6 79.6 85.5 91.3 102.9 76.9 83.7 90.4 97.1 103.7 116.8 85.0 92.6 100.0 107.3 114.5 128.7 92.9 101.1 109.1 117.1 124.9 140.1 100.5 109.3 117.9 126.4 134.7 150.9

8M-50

HT Synchrous Belts

DYNA-SYNC

SELECTION


DYNA-SYNC

SELECTION HT200 Basic Horsepower Rating NOTE: Multiply rating by Belt Length Correction Factor from Ratio/Center Distance Tables Rated Horsepower for Small Sprocket (Number of Teeth and Pitch Diameter, Inches)

14M-40

HT Synchrous Belts Sprockets

RPM SMALL SHAFT 10 20 40 60 100 200 300 400 500 600 800 870 1000 1160 1200 1400 1600 1750 2000 2400 2800 3200 3600 4000

28 4.91

29 5.09

30 5.26

32 5.61

34 5.97

36 6.32

38 6.67

40 7.02

44 7.72

48 8.42

52 9.12

56 9.82

60 10.53

64 11.23

68 11.93

72 80 12.63 14.04

0.56 1.04 1.95 2.81 4.44 8.21 11.7 15.1 18.3 21.4 27.5 29.5 33.2 37.7 38.7 44.1 49.3 53.1 59.2 68.5 77.3 85.5 93.2 100.4

0.58 1.09 2.04 2.94 4.64 8.58 12.3 15.8 19.1 22.4 28.7 30.9 34.8 39.4 40.6 46.2 51.6 55.5 61.9 71.7 80.9 89.5 97.5 105.0

0.60 1.13 2.12 3.06 4.83 8.94 12.8 16.4 20.0 23.4 30.0 32.2 36.3 41.1 42.3 48.2 53.9 58.0 64.7 74.9 84.4 93.4 101.7 109.5

0.65 1.22 2.29 3.30 5.22 9.67 13.8 17.8 21.6 25.3 32.5 34.9 39.3 44.6 45.9 52.3 58.4 62.9 70.1 81.2 91.5 101.1 110.0 118.2

0.70 1.31 2.46 3.54 5.60 10.4 14.9 19.1 23.3 27.3 35.0 37.6 42.3 48.0 49.4 56.3 62.9 67.7 75.5 87.3 98.4 108.6 118.1 126.7

0.74 1.40 2.62 3.78 5.98 11.1 15.9 20.5 24.9 29.2 37.4 40.2 45.3 51.4 52.9 60.3 67.3 72.5 80.8 93.4 105.2 116.0 125.9 134.8

0.79 1.48 2.79 4.02 6.36 11.8 16.9 21.8 26.5 31.1 39.9 42.9 48.3 54.8 56.4 64.2 71.7 77.2 86.1 99.4 111.8 123.2 133.5

0.83 1.57 2.95 4.26 6.74 12.5 17.9 23.1 28.1 33.0 42.3 45.5 51.2 58.1 59.8 68.1 76.1 81.9 91.3 105.3 118.3 130.1

0.92 1.74 3.27 4.73 7.49 13.9 20.0 25.7 31.3 36.7 47.1 50.6 57.1 64.7 66.6 75.8 84.7 91.1 101.4 116.8 130.9 143.5

1.01 1.91 3.60 5.19 8.23 15.3 22.0 28.3 34.5 40.4 51.9 55.7 62.8 71.2 73.3 83.4 93.1 100.1 111.3 127.9 142.9

1.10 2.08 3.92 5.66 8.97 16.7 23.9 30.9 37.6 44.1 56.6 60.8 68.5 77.6 79.9 90.8 101.3 108.9 120.9 138.6

1.19 2.25 4.24 6.12 9.71 18.1 25.9 33.4 40.7 47.7 61.2 65.8 74.1 84.0 86.4 98.1 109.4 117.4 130.2 148.8

1.28 2.42 4.55 6.58 10.4 19.4 27.9 35.9 43.7 51.3 65.8 70.7 79.6 90.2 92.8 105.3 117.2 125.8 139.3

1.37 2.59 4.87 7.03 11.2 20.8 29.8 38.4 46.8 54.8 70.3 75.6 85.0 96.3 99.0 112.3 125.0 134.0 148.0

1.46 2.75 5.18 7.49 11.9 22.1 31.7 40.9 49.8 58.4 74.8 80.4 90.4 102.3 105.2 119.2 132.5 141.9 156.5

1.55 2.92 5.49 7.94 12.6 23.5 33.6 43.4 52.8 61.9 79.3 85.1 95.7 108.3 111.3 126.0 139.8 149.6 164.6

Rated Horsepower for Small Sprocket (Number of Teeth and Pitch Diameter, Inches)

14M-55

Conveyor Components Engineering

RPM SMALL SHAFT 10 20 40 60 100 200 300 400 500 600 800 870 1000 1160 1200 1400 1600 1750 2000 2400 2800 3200 3600 4000

1.72 3.25 6.11 8.83 14.0 26.1 37.4 48.3 58.7 68.8 88.0 94.5 106.2 119.9 123.2 139.2 154.0 164.3

28 4.91

29 5.09

30 5.26

32 5.61

34 5.97

36 6.32

38 6.67

40 7.02

44 7.72

48 8.42

52 9.12

56 9.82

60 10.53

64 11.23

68 11.93

72 12.63

80 14.04

0.83 1.57 2.93 4.22 6.66 12.3 17.6 22.6 27.5 32.2 41.2 44.2 49.8 56.5 58.1 66.1 73.9 79.6 88.7 102.7 115.9 128.3 139.8 150.6

0.87 1.63 3.06 4.40 6.96 12.9 18.4 23.7 28.7 33.6 43.1 46.3 52.1 59.1 60.8 69.2 77.4 83.3 92.9 107.5 121.3 134.2 146.3 157.5

0.90 1.70 3.18 4.59 7.25 13.4 19.2 24.7 30.0 35.1 45.0 48.3 54.4 61.7 63.5 72.3 80.8 87.0 97.0 112.3 126.7 140.1 152.6 164.2

0.97 1.83 3.43 4.95 7.82 14.5 20.7 26.7 32.4 38.0 48.7 52.4 59.0 66.9 68.8 78.4 87.6 94.3 105.2 121.7 137.2 151.7 165.0 177.3

1.04 1.96 3.68 5.31 8.40 15.6 22.3 28.7 34.9 40.9 52.4 56.4 63.5 72.0 74.1 84.4 94.3 101.6 113.3 131.0 147.6 163.0 177.1 190.0

1.11 2.09 3.93 5.67 8.97 16.7 23.8 30.7 37.3 43.8 56.1 60.3 68.0 77.1 79.4 90.4 101.0 108.8 121.3 140.2 157.7 174.0 188.8 202.2

1.18 2.23 4.18 6.03 9.54 17.7 25.4 32.7 39.8 46.6 59.8 64.3 72.4 82.2 84.6 96.3 107.6 115.9 129.1 149.1 167.7 184.7 200.2

1.25 2.36 4.42 6.38 10.1 18.8 26.9 34.7 42.2 49.4 63.5 68.2 76.9 87.2 89.7 102.2 114.2 122.9 136.9 158.0 177.5 195.2

1.39 2.61 4.91 7.09 11.2 20.9 29.9 38.6 47.0 55.1 70.7 76.0 85.6 97.1 99.9 113.7 127.0 136.7 152.1 175.2 196.3 215.3

1.52 2.87 5.40 7.79 12.4 23.0 32.9 42.5 51.7 60.6 77.8 83.6 94.2 106.9 110.0 125.1 139.6 150.1 166.9 191.9 214.3

1.66 3.13 5.88 8.49 13.5 25.0 35.9 46.3 56.4 66.1 84.8 91.2 102.7 116.5 119.8 136.2 152.0 163.3 181.3 207.9

1.79 3.38 6.36 9.18 14.6 27.1 38.9 50.1 61.0 71.5 91.8 98.7 111.1 125.9 129.6 147.2 164.0 176.2 195.3 223.3

1.92 3.63 6.83 9.87 15.7 29.1 41.8 53.9 65.6 76.9 98.7 106.0 119.4 135.3 139.1 158.0 175.9 188.7 208.9

2.06 3.88 7.30 10.6 16.7 31.2 44.7 57.7 70.2 82.3 105.5 113.3 127.6 144.5 148.6 168.5 187.4 200.9 222.0

2.19 4.13 7.77 11.2 17.8 33.2 47.6 61.4 74.7 87.6 112.2 120.6 135.6 153.5 157.8 178.9 198.7 212.8 234.7

2.32 4.38 8.24 11.9 18.9 35.2 50.5 65.1 79.2 92.8 118.9 127.7 143.6 162.4 167.0 189.0 209.7 224.4

2.58 4.87 9.17 13.2 21.0 39.1 56.1 72.4 88.0 103.2 132.0 141.7 159.2 179.8 184.8 208.7 231.0 246.5

Operation in shaded area will result in a reduction of belt life.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-24

ENGINEERING/TECHNICAL PAGES PT11- 4


HT200 Basic Horsepower Rating NOTE: Multiply rating by Belt Length Correction Factor from Ratio/Center Distance Tables 29 5.09 1.45 2.72 5.10 7.34 11.6 21.5 30.7 39.4 47.9 56.1 71.8 77.2 86.9 98.5 101.4 115.4 129.0 138.8 154.9 179.2 202.2 223.7 243.8 262.4

30 5.26 1.51 2.83 5.30 7.64 12.1 22.4 32.0 41.1 49.9 58.5 74.9 80.5 90.7 102.9 105.8 120.5 134.7 145.0 161.7 187.2 211.1 233.5 254.4 273.6

32 5.61 1.62 3.05 5.72 8.25 13.0 24.2 34.6 44.5 54.1 63.3 81.2 87.3 98.3 111.5 114.7 130.6 146.0 157.2 175.3 202.9 228.7 252.8 275.1 295.5

Rated Horsepower for Small Sprocket (Number of Teeth and Pitch Diameter, Inches) 36 38 40 44 48 52 56 6.32 6.67 7.02 7.72 8.42 9.12 9.82

14M-115 RPM SMALL SHAFT 10 20 40 60 100 200 300 400 500 600 800 870 1000 1160 1200 1400 1600 1750 2000 2400 2800 3200 3600 4000

28 4.91

29 5.09

30 5.26

32 5.61

34 5.97

1.94 3.65 6.84 9.85 15.5 28.8 41.1 52.8 64.1 75.1 96.1 103.2 116.2 131.8 135.6 154.3 172.5 185.7 207.1 239.7 270.4 299.3 326.3 351.4

2.03 3.81 7.13 10.3 16.2 30.0 42.9 55.2 67.0 78.5 100.5 108.0 121.6 137.9 141.9 161.5 180.5 194.4 216.8 250.9 283.1 313.2 341.3 367.4

2.11 3.96 7.43 10.7 16.9 31.3 44.7 57.6 69.9 81.9 104.9 112.7 127.0 144.0 148.2 168.7 188.5 203.0 226.4 262.0 295.5 326.9 356.1 383.1

2.27 4.27 8.01 11.5 18.3 33.8 48.4 62.3 75.7 88.7 113.7 122.2 137.6 156.1 160.6 182.9 204.4 220.1 245.5 284.0 320.2 353.9 385.1 413.7

2.43 4.58 8.59 12.4 19.6 36.4 52.0 67.0 81.4 95.4 122.4 131.5 148.2 168.1 173.0 197.0 220.1 237.0 264.3 305.7 344.4 380.2 413.3 443.3

2.59 4.89 9.17 13.2 20.9 38.9 55.6 71.7 87.1 102.1 131.0 140.8 158.6 180.0 185.2 210.9 235.7 253.8 282.9 327.0 368.1 406.0 440.6 471.9

2.75 5.19 9.75 14.1 22.3 41.3 59.2 76.3 92.8 108.8 139.5 150.0 169.0 191.8 197.4 224.7 251.1 270.3 301.3 348.0 391.3 431.1 467.1

2.92 5.50 10.3 14.9 23.6 43.8 62.8 80.9 98.4 115.4 148.1 159.1 179.3 203.5 209.4 238.4 266.4 286.7 319.4 368.7 414.1 455.5

3.23 6.10 11.5 16.5 26.2 48.7 69.9 90.1 109.6 128.5 164.9 177.3 199.7 226.6 233.2 265.4 296.4 318.9 354.9 408.9 458.1 502.4

3.55 6.70 12.6 18.2 28.8 53.6 76.9 99.1 120.6 141.4 181.5 195.1 219.8 249.3 256.6 291.9 325.8 350.3 389.5 447.7 500.1

3.86 7.29 13.7 19.8 31.4 58.4 83.8 108.1 131.5 154.2 197.9 212.8 239.7 271.8 279.6 317.9 354.6 381.0 423.1 485.1

4.18 7.88 14.8 21.4 34.0 63.2 90.7 117.0 142.3 166.9 214.2 230.2 259.2 293.8 302.3 343.5 382.8 411.0 455.8 521.0

60 10.53 3.20 6.05 11.4 16.4 26.1 48.6 69.7 89.9 109.3 128.2 164.5 176.7 199.0 225.4 231.9 263.3 293.1 314.5 348.2

64 11.23 3.43 6.47 12.2 17.6 27.9 51.9 74.5 96.1 116.9 137.1 175.8 188.9 212.6 240.8 247.6 280.9 312.4 334.9 370.1

68 11.93 3.64 6.88 13.0 18.7 29.7 55.3 79.3 102.3 124.5 145.9 187.1 200.9 226.1 255.8 263.1 298.1 331.2 354.7 391.2

72 12.63 3.86 7.30 13.7 19.8 31.5 58.6 84.1 108.5 131.9 154.7 198.2 212.8 239.3 270.7 278.3 315.1 349.6 374.0

80 14.04 4.30 8.12 15.3 22.1 35.0 65.2 93.6 120.7 146.7 171.9 220.1 236.2 265.4 299.7 308.0 347.9 385.0 410.8

Sprockets

28 4.91 1.39 2.61 4.89 7.03 11.1 20.5 29.3 37.7 45.8 53.6 68.6 73.7 83.0 94.1 96.9 110.2 123.2 132.6 147.9 171.2 193.2 213.8 233.1 251.0

60 10.53

64 11.23

68 11.93

72 12.63

80 14.04

4.49 8.47 15.9 23.0 36.5 68.0 97.5 125.8 153.1 179.5 230.3 247.4 278.6 315.6 324.7 368.6 410.4 440.3 487.4

4.80 9.06 17.0 24.6 39.1 72.7 104.3 134.6 163.7 192.0 246.2 264.5 297.7 337.1 346.7 393.2 437.4 468.8 518.1

5.10 9.64 18.1 26.2 41.6 77.4 111.1 143.2 174.2 204.3 261.9 281.3 316.5 358.1 368.3 417.4 463.7 496.6 547.7

5.41 10.2 19.2 27.8 44.1 82.1 117.8 151.8 184.7 216.5 277.4 298.0 335.1 379.0 389.6 441.1 489.4 523.5

6.02 11.4 21.4 30.9 49.0 91.3 131.0 168.9 205.4 240.7 308.1 330.7 371.6 419.6 431.2 487.1 538.9 575.1

Operation in shaded area will result in a reduction of belt life.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-25

Conveyor Components

RPM SMALL SHAFT 10 20 40 60 100 200 300 400 500 600 800 870 1000 1160 1200 1400 1600 1750 2000 2400 2800 3200 3600 4000

Engineering

34 5.97 1.74 3.27 6.14 8.85 14.0 26.0 37.2 47.8 58.2 68.2 87.4 93.9 105.8 120.1 123.6 140.7 157.2 169.3 188.8 218.4 246.0 271.6 295.2 316.7

Rated Horsepower for Small Sprocket (Number of Teeth and Pitch Diameter, Inches) 36 38 40 44 48 52 56 6.32 6.67 7.02 7.72 8.42 9.12 9.82 1.85 1.97 2.08 2.31 2.54 2.76 2.98 3.49 3.71 3.93 4.36 4.78 5.21 5.63 6.55 6.96 7.37 8.19 8.99 9.80 10.6 9.45 10.0 10.6 11.8 13.0 14.1 15.3 15.0 15.9 16.8 18.7 20.6 22.4 24.3 27.8 29.5 31.3 34.8 38.3 41.7 45.2 39.7 42.3 44.8 49.9 54.9 59.9 64.8 51.2 54.5 57.8 64.3 70.8 77.2 83.6 62.2 66.3 70.3 78.3 86.1 93.9 101.7 72.9 77.7 82.4 91.8 101.0 110.2 119.2 93.6 99.7 105.8 117.8 129.6 141.4 153.0 100.6 107.1 113.7 126.6 139.4 152.0 164.4 113.3 120.7 128.1 142.7 157.0 171.2 185.2 128.6 137.0 145.3 161.9 178.1 194.1 209.9 132.3 141.0 149.6 166.6 183.3 199.7 215.9 150.6 160.5 170.3 189.6 208.5 227.1 245.3 168.4 179.4 190.3 211.7 232.7 253.3 273.4 181.3 193.1 204.8 227.8 250.2 272.2 293.6 202.1 215.2 228.1 253.5 278.2 302.2 325.6 233.6 248.6 263.3 292.1 319.8 346.5 372.1 262.9 279.5 295.8 327.2 357.2 290.0 307.9 325.4 358.8 314.7 333.7 337.1

14M-85

HT Synchrous Belts

DYNA-SYNC

SELECTION

ENGINEERING/TECHNICAL PAGES PT11- 4


DYNA-SYNC

SELECTION HT200 Basic Horsepower Rating NOTE: Multiply rating by Belt Length Correction Factor from Ratio/Center Distance Tables

14M-170

HT Synchrous Belts Sprockets

RPM SMALL SHAFT 10 20 40 60 100 200 300 400 500 600 800 870 1000 1160 1200 1400 1600 1750 2000 2400 2800 3200 3600 4000

28 4.91

29 5.09

30 5.26

32 5.61

34 5.97

2.96 5.55 10.4 15.0 23.6 43.7 62.4 80.3 97.4 114.1 146.1 156.9 176.7 200.3 206.1 234.6 262.1 282.2 314.7 364.3 411.0 454.9 496.0 534.2

3.08 5.79 10.8 15.6 24.7 45.6 65.2 83.9 101.9 119.3 152.8 164.2 184.9 209.7 215.7 245.5 274.4 295.5 329.5 381.4 430.3 476.1 518.8 558.5

3.20 6.03 11.3 16.3 25.7 47.6 68.0 87.5 106.3 124.5 159.5 171.4 193.0 218.9 225.2 256.4 286.6 308.6 344.1 398.3 449.2 496.9 541.3 582.3

3.45 6.50 12.2 17.6 27.8 51.4 73.6 94.7 115.0 134.8 172.8 185.7 209.2 237.3 244.2 278.0 310.7 334.6 373.1 431.7 486.7 537.9 585.3 628.9

3.70 6.96 13.1 18.8 29.8 55.3 79.1 101.8 123.8 145.0 186.0 199.9 225.2 255.5 262.9 299.4 334.6 360.3 401.8 464.7 523.4 578.0 628.2 673.9

Rated Horsepower for Small Sprocket (Number of Teeth and Pitch Diameter, Inches) 36 38 40 44 48 52 56 6.32 6.67 7.02 7.72 8.42 9.12 9.82

3.94 7.43 13.9 20.1 31.8 59.1 84.6 108.9 132.4 155.2 199.1 214.0 241.1 273.6 281.6 320.6 358.3 385.8 430.0 497.1 559.5 617.1 669.7 717.3

4.19 7.89 14.8 21.4 33.8 62.8 90.0 116.0 141.0 165.3 212.1 228.0 256.9 291.5 300.0 341.6 381.7 410.9 457.9 529.0 594.8 655.2 710.0

4.43 8.35 15.7 22.6 35.9 66.6 95.4 123.0 149.6 175.4 225.0 241.9 272.6 309.3 318.3 362.4 404.9 435.8 485.5 560.3 629.4 692.4

4.91 9.27 17.4 25.1 39.8 74.1 106.2 136.9 166.5 195.3 250.6 269.4 303.6 344.4 354.4 403.4 450.5 484.7 539.5 621.5 696.3 763.6

5.39 10.2 19.1 27.6 43.8 81.5 116.8 150.6 183.3 214.9 275.9 296.6 334.1 379.0 390.0 443.6 495.2 532.5 592.0 680.5 760.1

5.87 11.1 20.8 30.1 47.7 88.8 127.4 164.3 199.9 234.4 300.9 323.4 364.3 413.1 425.0 483.2 539.0 579.2 643.1 737.3

6.35 12.0 22.5 32.6 51.6 96.1 137.9 177.8 216.3 253.7 325.6 349.9 394.1 446.7 459.5 522.1 581.8 624.8 692.8 791.9

60 10.53

64 11.23

68 72 80 11.93 12.63 14.04

6.82 12.9 24.2 35.0 55.5 103.4 148.3 191.2 232.7 272.8 350.0 376.1 423.4 479.7 493.5 560.2 623.8 669.3 740.9

7.29 13.8 25.9 37.4 59.4 110.5 158.6 204.5 248.8 291.8 374.2 402.0 452.4 512.3 526.9 597.7 664.8 712.6 787.5

7.76 14.6 27.6 39.8 63.2 117.7 168.8 217.7 264.8 310.5 398.0 427.6 481.0 544.4 559.8 634.4 704.8 754.8 832.4

8.22 15.5 29.2 42.2 67.0 124.8 179.0 230.8 280.8 329.1 421.7 452.9 509.3 576.0 592.2 670.4 743.9 795.8

9.15 17.3 32.5 47.0 74.5 138.8 199.1 256.8 312.2 365.9 468.3 502.7 564.8 637.8 655.5 740.4 819.2 874.2

Operation in shaded area will result in a reduction of belt life.

Conveyor Components Engineering FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-26

ENGINEERING/TECHNICAL PAGES PT11- 4


HT100 Basic Horsepower Rating NOTE: Multiply rating by Belt Length Correction Factor from Ratio/Center Distance Tables 34 2.1 0.03 0.06 0.11 0.16 0.26 0.48 0.69 0.89 1.09 1.27 1.64 1.99 2.34 2.67 2.99 3.31 3.62 4.23 4.81 5.37 5.91 6.43 7.66 8.76 10.6 11.8

36 2.3 0.03 0.06 0.12 0.18 0.28 0.52 0.75 0.96 1.17 1.38 1.78 2.16 2.53 2.90 3.25 3.59 3.93 4.59 5.23 5.84 6.43 6.99 8.32 9.51 11.5 12.7

56 3.5 0.06 0.11 0.21 0.30 0.48 0.89 1.29 1.67 2.04 2.40 3.10 3.78 4.44 5.08 5.71 6.32 6.92 8.08 9.19 10.2 11.3 12.2 14.3 16.1

60 3.8 0.06 0.12 0.22 0.32 0.51 0.97 1.39 1.81 2.21 2.60 3.36 4.10 4.81 5.51 6.19 6.85 7.50 8.75 9.95 11.1 12.2 13.2 15.4 17.1

64 4.0 0.07 0.13 0.24 0.35 0.55 1.04 1.50 1.94 2.38 2.80 3.62 4.41 5.18 5.93 6.66 7.38 8.07 9.41 10.7 11.9 13.0 14.1 16.4 18.1

68 4.2 0.07 0.13 0.25 0.37 0.59 1.11 1.60 2.08 2.54 3.00 3.87 4.72 5.55 6.35 7.13 7.89 8.64 10.1 11.4 12.7 13.9 15.0 17.4

38 2.38 0.06 0.11 0.22 0.31 0.50 0.93 1.33 1.73 2.10 2.47 3.19 3.88 4.55 5.20 5.83 6.46 7.07 8.25 9.39 10.5 11.6 12.6 15.0 17.1 20.5 22.6

Rated Horsepower for Small Sprocket (Number of Grooves and Pitch Diameter, Inches) 40 44 45 48 50 52 2.5 2.8 2.8 3.0 3.1 3.3 0.06 0.07 0.07 0.08 0.08 0.09 0.12 0.14 0.14 0.15 0.16 0.17 0.23 0.26 0.27 0.29 0.30 0.31 0.33 0.37 0.38 0.42 0.44 0.46 0.53 0.60 0.61 0.66 0.69 0.73 0.99 1.12 1.15 1.24 1.30 1.36 1.43 1.61 1.65 1.79 1.88 1.97 1.84 2.08 2.14 2.32 2.43 2.55 2.25 2.54 2.61 2.83 2.97 3.11 2.64 2.99 3.07 3.33 3.50 3.67 3.41 3.86 3.97 4.30 4.52 4.74 4.15 4.70 4.83 5.24 5.50 5.77 4.87 5.51 5.67 6.15 6.46 6.78 5.57 6.31 6.49 7.04 7.40 7.76 6.25 7.08 7.29 7.90 8.31 8.71 6.92 7.84 8.07 8.75 9.20 9.65 7.58 8.59 8.84 9.58 10.1 10.6 8.85 10.0 10.3 11.2 11.8 12.3 10.1 11.4 11.8 12.7 13.4 14.0 11.3 12.8 13.1 14.2 14.9 15.7 12.4 14.0 14.4 15.6 16.4 17.2 13.5 15.3 15.7 17.0 17.9 18.7 16.0 18.1 18.6 20.1 21.1 22.0 18.3 20.6 21.1 22.8 23.8 24.8 21.8 24.3 24.9 26.6 27.6 23.9

56 3.5 0.10 0.18 0.34 0.50 0.79 1.49 2.15 2.78 3.40 4.00 5.17 6.30 7.40 8.47 9.52 10.5 11.5 13.5 15.3 17.1 18.8 20.3 23.9 26.8

60 3.8 0.10 0.20 0.37 0.54 0.86 1.61 2.32 3.01 3.68 4.33 5.60 6.83 8.02 9.18 10.3 11.4 12.5 14.6 16.6 18.5 20.3 21.9 25.7 28.6

64 4.0 0.11 0.21 0.40 0.58 0.92 1.73 2.50 3.24 3.96 4.66 6.03 7.35 8.64 9.89 11.1 12.3 13.5 15.7 17.8 19.8 21.7 23.5 27.3 30.2

68 4.2 0.12 0.22 0.42 0.62 0.98 1.85 2.67 3.47 4.24 4.99 6.46 7.87 9.25 10.6 11.9 13.2 14.4 16.8 19.0 21.2 23.1 25.0 28.9

5M-25 RPM SMALL SHAFT 10 20 40 60 100 200 300 400 500 600 800 1000 1200 1400 1600 1800 2000 2400 2800 3200 3600 4000 5000 6000 8000 10000 12000 14000

32 2.0 0.05 0.09 0.17 0.25 0.40 0.74 1.06 1.36 1.66 1.95 2.51 3.04 3.56 4.07 4.56 5.05 5.52 6.44 7.32 8.17 8.99 9.79 11.6 13.3 16.1 18.2 19.2

34 2.1 0.05 0.10 0.19 0.27 0.43 0.80 1.15 1.48 1.81 2.12 2.73 3.32 3.89 4.45 4.99 5.52 6.04 7.04 8.01 8.95 9.85 10.7 12.8 14.6 17.6 19.7

36 2.3 0.06 0.11 0.20 0.29 0.46 0.86 1.24 1.61 1.96 2.30 2.96 3.60 4.22 4.83 5.41 5.99 6.56 7.65 8.71 9.73 10.7 11.7 13.9 15.9 19.1 21.2

Shaded area indicates sprocket and RPM which can be used only if a reduction in belt life is allowable. FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-27

ENGINEERING/TECHNICAL PAGES PT11- 4

Conveyor Components

32 2.0 0.03 0.06 0.10 0.15 0.24 0.44 0.63 0.82 1.00 1.17 1.50 1.83 2.14 2.44 2.74 3.03 3.31 3.86 4.39 4.90 5.40 5.87 6.99 8.00 9.69 10.9 11.5

Engineering

RPM SMALL SHAFT 10 20 40 60 100 200 300 400 500 600 800 1000 1200 1400 1600 1800 2000 2400 2800 3200 3600 4000 5000 6000 8000 10000 12000 14000

Sprockets

38 2.38 0.04 0.07 0.13 0.19 0.30 0.56 0.80 1.04 1.26 1.48 1.91 2.33 2.73 3.12 3.50 3.87 4.24 4.95 5.64 6.30 6.93 7.54 8.97 10.2 12.3 13.6

Rated Horsepower for Small Sprocket (Number of Grooves and Pitch Diameter, Inches) 40 44 45 48 50 52 2.5 2.8 2.8 3.0 3.1 3.3 0.04 0.04 0.04 0.05 0.05 0.05 0.07 0.08 0.08 0.09 0.10 0.10 0.14 0.16 0.16 0.17 0.18 0.19 0.20 0.22 0.23 0.25 0.26 0.27 0.32 0.36 0.37 0.40 0.42 0.44 0.59 0.67 0.69 0.74 0.78 0.82 0.86 0.96 0.99 1.07 1.13 1.18 1.11 1.25 1.28 1.39 1.46 1.53 1.35 1.52 1.57 1.70 1.78 1.87 1.59 1.79 1.84 2.00 2.10 2.20 2.05 2.31 2.38 2.58 2.71 2.84 2.49 2.82 2.90 3.14 3.30 3.46 2.92 3.31 3.40 3.69 3.88 4.07 3.34 3.78 3.89 4.22 4.44 4.65 3.75 4.25 4.37 4.74 4.99 5.23 4.15 4.71 4.84 5.25 5.52 5.79 4.55 5.15 5.30 5.75 6.05 6.34 5.31 6.02 6.19 6.72 7.06 7.40 6.04 6.85 7.05 7.64 8.04 8.42 6.75 7.65 7.87 8.53 8.97 9.40 7.43 8.42 8.66 9.39 9.86 10.3 8.09 9.16 9.42 10.2 10.7 11.2 9.61 10.9 11.2 12.1 12.6 13.2 11.0 12.3 12.7 13.7 14.3 14.9 13.1 14.6 14.9 15.9 16.6 14.4

5M-15

HT Synchrous Belts

DYNA-SYNC

SELECTION


DYNA-SYNC

SELECTION HT100 Basic Horsepower Rating NOTE: Multiply rating by Belt Length Correction Factor from Ratio/Center Distance Tables

8M-20 RPM Small Sprocket

HT Synchrous Belts Sprockets

10 20 40 60 100 200 300 400 500 600 700 800 870 1000 1160 1200 1400 1600 1750 2000 2400 2800 3200 3500 4000 4500 5000 5500 PD: MM Inches

22

24

26

28

0.02 0.04 0.08 0.12 0.22 0.44 0.66 087 1.09 1.31 1.53 1.75 1.90 2.18 2.53 2.62 3.05 3.48 3.81 4.34 5.19 6.03

0.03 0.05 0.10 0.15 0.25 0.50 0.72 0.95 1.19 1.43 1.67 1.91 2.07 2.38 2.76 2.85 3.33 3.80 4.15 4.73 5.65 6.56

0.03 0.06 0.12 0.18 0.30 0.60 0.87 1.12 1.37 1.62 1.86 2.09 2.26 2.58 2.99 3.09 3.60 4.11 4.49 5.11 6.11 7.08 8.04

0.04 0.07 0.14 0.22 0.36 0.71 1.03 1.33 1.63 1.92 2.20 2.48 2.68 3.03 3.46 3.56 4.08 4.58 4.95 5.61 6.69 7.75 8.79

0.04 0.08 0.17 0.25 0.42 0.83 1.20 1.56 1.91 2.25 2.58 2.91 3.13 3.54 4.04 4.16 4.77 5.36 5.79 6.49 7.58 8.62 9.60 10.36

0.05 0.10 0.19 0.29 0.48 0.96 1.39 1.80 2.20 2.60 2.98 3.36 3.62 4.09 4.67 4.81 5.50 6.18 6.68 7.49 8.74 9.93 11.06 11.86 13.12

0.06 0.11 0.22 0.33 0.55 1.10 1.59 2.06 2.52 2.97 3.41 3.84 4.13 4.68 5.33 5.49 6.29 7.06 7.63 8.55 9.97 11.33 12.61 13.52 14.94 16.23

0.06 0.13 0.25 0.38 0.63 1.25 1.80 2.34 2.86 3.36 3.86 4.35 4.68 5.30 6.04 6.22 7.12 7.99 8.64 9.68 11.28 12.80 14.24 15.26 16.85 18.29 19.57

56.0 2.21

61.1 2.41

66.2 2.61

71.3 2.81

76.4 3.01

81.5 3.21

86.6 3.41

91.7 3.61

8M-30 RPM Small Sprocket

Conveyor Components Engineering

10 20 40 60 100 200 300 400 500 600 700 800 870 1000 1160 1200 1400 1600 1750 2000 2400 2800 3200 3500 4000 4500 5000 5500 PD: MM Inches

HT100 Horsepower Rating–20MM Wide Belt (.79 in.) No. Teeth 30 32 34 36 38 40 44 48 0.07 0.14 0.29 0.43 0.72 1.41 2.03 2.63 3.21 3.78 4.34 4.89 5.26 5.95 6.79 6.99 8.61 8.98 9.70 10.87 12.66 14.36 15.96 17.10 18.86 20.44 21.85 23.05 96.8 3.81

0.08 0.15 0.30 0.45 0.76 1.51 2.20 2.84 3.47 4.09 4.69 5.28 5.69 6.43 7.33 7.55 8.64 9.69 10.47 11.72 13.64 15.46 17.17 18.37 20.23 21.89 23.33 24.55 101.9 4.01

0.08 0.17 0.33 0.50 0.83 1.66 2.39 3.10 3.78 4.45 5.11 5.75 6.19 7.00 7.97 8.20 9.38 10.52 11.35 12.70 14.75 16.67 18.45 19.69 21.57 23.20 24.55 25.61 112.0 4.41

56

64

72

80

0.09 0.18 0.36 0.55 0.91 1.79 2.59 3.35 4.09 4.81 5.51 6.21 6.68 7.55 8.59 8.85 10.11 11.32 12.21 13.64 15.81 17.82 19.66 20.92 22.78 24.33 25.52

0.11 0.21 0.42 0.64 1.06 2.06 2.97 3.84 4.69 5.51 6.32 7.11 7.65 864 9.82 10.11 11.52 12.89 13.88 15.46 17.82 19.94 21.83 23.06 24.77

0.12 0.24 0.48 0.73 1.21 2.33 3.35 4.33 5.28 6.21 7.11 7.99 8.59 9.69 11.00 11.32 12.89 14.38 15.46 17.17 19.66 21.83 23.65 24.77

0.14 0.27 0.55 0.82 1.36 2.59 3.72 4.81 5.86 6.88 7.88 8.85 9.51 10.72 12.15 12.50 14.20 15.81 16.96 18.76 21.31 23.44 25.09

0.15 0.30 0.61 0.91 1.51 2.84 4.09 5.28 6.43 7.55 8.64 9.69 10.41 11.72 13.27 13.64 15.46 17.17 18.37 20.23 22.78 24.77

122.2 4.81

142.6 5.61

163.0 6.42

183.3 7.22

203.7 8.02

HT100 Horsepower Rating–30MM Wide Belt (1.18 in.) No. Teeth 30 32 34 36 38 40 44 48

22

24

26

28

0.03 0.07 0.13 0.20 0.34 0.69 1.03 1.38 1.72 2.07 2.41 2.76 3.00 3.44 3.99 4.13 4.81 5.49 6.00 6.85 8.19 9.52

0 04 0.08 0.16 0.24 0.40 0.78 1.13 1.50 1.88 2.26 2.63 3.01 3.27 3.76 4.35 4.50 5.25 5.99 6.54 7.46 8.92 10.35

0.05 0.10 0.19 0.29 0.48 0.94 1.37 1.77 2.17 2.55 2.93 3.30 3.56 4.07 4.71 4.87 5.68 6.48 7.08 8.07 9.64 11.18 12.70

0.06 0.11 0.23 0.34 0.57 1.12 1.62 2.10 2.57 3.03 3.48 3.92 4.22 4.78 5.45 5.62 6.43 7.23 7.82 8.85 10.56 12.24 13.89

0.07 0.13 0.26 0.40 0.66 1.31 1.90 2.46 3.01 3.54 4.07 4.58 4.94 5.59 6.37 6.57 7.52 8.45 9.13 10.25 11.96 13.60 15.17 16.38

0.08 0.15 0.31 0.46 0.76 1.52 2.19 2.84 3.48 4.09 4.70 5.29 5.70 6.45 7.36 7.58 8.68 9.75 10.54 11.82 13.80 15.68 17.47 18.75 20.76

0.09 0.17 0.35 0.52 0.87 1.74 2.51 3.25 3.98 4.68 5.37 6.05 6.52 7.38 8.41 8.66 9.92 11.14 12.04 13.50 15.75 17.89 19.92 21.37 23.64 25.71

0.10 0.20 0.40 0.59 0.99 1.97 2.85 3.69 4.51 5.31 6.09 6.86 7.39 8.36 9.52 9.81 11.23 12.61 13.63 15.28 17.81 20.22 22.50 24.13 26.66 28.98 31.05

56.0 2.21

61.1 2.41

66.2 2.61

71.3 2.81

76.4 3.01

81.5 3.21

86.6 3.41

91.7 3.61

0.11 0.23 0.45 0.68 1.13 2.22 3.20 4.15 5.07 5.96 6.84 7.71 8.30 9.39 10.70 11.03 12.62 14.17 15.30 17.15 19.99 22.68 25.22 27.03 29.85 32.40 34.67 36.64 96.8 3.81

0.12 0.24 0.48 0.72 1.19 2.39 3.46 4.48 5.48 6.45 7.40 8.33 8.97 10.15 11.56 11.91 13.62 15.29 16.51 18.50 21.55 24.43 27.14 29.06 32.03 34.70 37.04 39.05 101.9 4.01

0.13 0.26 0.53 0.79 1.31 2.62 3.77 4.89 5.97 7.02 8.05 9.06 9.76 11.03 12.57 12.94 14.80 16.60 17.91 20.04 23.29 26.34 29.18 31.17 34.19 36.83 39.05 40.82 112.0 4.41

56

64

72

80

0.14 0.29 0.57 0.86 1.43 2.83 4.08 5.28 6.45 7.59 8.70 9.79 10.54 11.91 13.56 13.96 15.95 17.87 19.28 21.55 24.98 28.17 31.11 33.13 36.15 38. 67 40.68

0 17 0.33 0.67 1.00 1.67 325 4.69 6.06 7.40 8.70 9.97 11.21 12.07 13.62 15.49 15.95 18.19 20.35 21.91 24.43 28.17 31.57 34.60 36.60 39.40

0.19 0.38 0.76 1.15 1.91 3.67 5.28 6.83 8.33 9.79 11.21 12.60 13.56 15.29 17.36 17.87 20.35 22.72 24.43 27.14 31.11 34.60 37.56 39.40

0.21 0.43 0.86 1.29 2.15 4.08 5.87 7.59 9.25 10.86 12.43 13.96 15.01 16.92 19.18 19.74 22.43 24.98 26.81 29.67 33.77 37.22 39.94

0.24 0.48 0.96 1.43 2.39 4.48 6.45 8.33 10.15 11.91 13.62 15.29 16.43 18.50 20.95 21.55 24.43 27.14 29.06 32.03 36.15 39.40

122.2 4.81

142.6 5.61

163.0 6.42

183.3 7.22

203.7 8.02

Operation in shaded area will result in a reduction of belt life.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-28

ENGINEERING/TECHNICAL PAGES PT11- 4


DYNA-SYNC

SELECTION HT100 Basic Horsepower Rating NOTE: Multiply rating by Belt Length Correction Factor from Ratio/Center Distance Tables

8M-50 32 0.13 0.26 0.53 0.79 1.32 2.63 3.80 4.93 6.02 7.09 8.14 9.17 9.88 11.18 12.75 13.13 15.04 16.89 18.26 20.48 23.91 27.19 30.30 32.53 36.04

34 0.15 0.30 0.60 0.91 1.51 3.01 4.35 5.63 6.89 8.11 9.31 10.48 11.29 12.78 14.57 15.01 17.18 19.30 20.86 23.39 27.29 31.01 34.54 37.07 41.03 44.67

36 0.17 0.34 0.69 1.03 1.71 3.41 4.93 6.39 7.80 9.19 10.54 11.88 12.79 14.47 16.50 17.00 19.45 21.85 23.61 26.47 30.87 35.06 39.03 41.86 46.30 50.35 53.99

71.3 2.81

76.4 3.01

81.5 3.21

86.6 3.41

91.7 3.61

8M-85 RPM Small Sprocket 10 20 40 60 100 200 300 400 500 600 700 800 870 1000 1160 1200 1400 1600 1750 2000 2400 2800 3200 3500 4000 4500 5000 5500 PD: MM Inches

38 0.20 0.39 0.79 1.18 1.96 3.84 5.54 7.18 8.78 10.33 11.85 13.35 14.38 16.27 18.54 19.10 21.85 24.54 26.51 29.72 34.64 39.32 43.75 46.91 51.82 56.30 60.30 63.81 96.8 3.81

40 0.21 0.41 0.83 1.24 2.07 4.13 6.00 7.77 9.49 11.17 12.81 14.43 15.54 17.58 20.03 20.63 23.60 26.49 28.61 32.06 37.35 42.35 47.08 50.43 55.63 60.32 64.47 68.04 101.9 4.01

44 0.23 0.45 0.91 1.36 2.27 4.53 6.53 8.46 10.33 12.16 13.95 15.70 16.91 19.11 21.77 22.42 25.63 28.75 31.04 34.74 40.38 45.69 50.65 54.12 59.42 64.08 68.04 71.25 112.0 4.41

48 0.25 0.50 0.99 1.49 2.48 4.90 7.07 9.15 11.17 13.14 15.06 16.95 18.25 20.63 23.48 24.18 27.63 30.97 33.41 37.35 43.32 48.89 54.02 57.57 62.88 67.37 70.99

56 0.29 0.58 1.16 1.74 2.89 5.63 8.12 10.50 12.81 15.06 17.26 19.42 20.90 23.60 26.83 27.63 31.52 35.27 37.99 42.35 48.89 54.83 60.14 63.68 68.68

64 0.33 0.66 1.32 1.98 3.31 6.35 9.15 11.83 14.43 16.95 19.42 21.83 23.48 26.49 30.09 30.97 35.27 39.38 42.35 47.08 54.02 60.14 65.38 68.58

72 0.37 0.74 1.49 2.23 3.72 7.07 10.16 13.14 16.01 18.81 21.53 24.18 26.01 29.31 33.25 34.21 38.88 43.32 46.50 51.51 58.69 64.78 69.65

80 0.41 0.83 1.65 2.48 4.13 7.77 11.17 14.43 17.58 20.63 23.60 26.49 28.47 32.06 36.31 37.35 42.35 47.08 50.43 55.63 62.88 68.68

122.2 4.81

142.6 5.61

163.0 6.42

183.3 7.22

203.7 8.02

HT Synchrous Belts

30 0.11 0.23 0.46 0.69 1.15 2.28 3.29 4.26 5.21 7.14 7.04 7.94 8.55 9.68 11.04 11.37 13.02 14.64 15.82 17.75 20.73 23.58 26.30 28.41

Sprockets

28 0.10 0.20 0.39 0.59 0.98 1.94 2.81 3.64 4.45 5.25 6.02 6.79 7.31 8.28 9.44 9.73 11.14 12.52 13.54 15.33 18.30 21.22 24.09

HT100 Horsepower Rating–85MM Wide Belt (3.35 in.) No. Teeth 34 0.26 0.53 1.05 1.58 2.63 5.24 7.56 9.80 11.98 14.10 16.19 18.23 19.65 22.23 25.34 26.11 29.89 33.58 36.29 40.70 47.50 53.98 60.14 64.55 71.47 77.84

36 0.30 0.60 1.19 1.79 2.98 5.94 8.57 11.11 13.58 15.98 18.34 20.66 22.26 25.18 28.70 29.57 33.84 38.01 41.07 46.06 53.73 61.03 67.95 72.90 80.65 87.75 94.15

86.6 3.41

91.7 3.61

38 0.34 0.68 1.37 2.05 3.42 6.68 9.64 12.49 15.26 17.97 20.62 23.22 25.02 28.30 32.25 33.23 38.02 42.70 46.13 51.71 60.29 68.45 76.18 81.69 90.29 98.13 105.17 111.35 96.8 3.81

40 0.36 0.72 1.44 2.16 3.60 7.19 10.43 13.51 16.50 19.43 22.29 25.10 27.03 30.57 34.84 35.89 41.06 46.09 49.79 55.79 65.00 73.73 81.98 87.83 96.92 105.15 112.46 118.77 101.9 4.01

44 0.40 0.79 1.58 2.37 3.96 7.88 11.36 14.72 17.97 21.15 24.26 27.31 29.41 33.25 37.87 39.01 44.60 50.03 54.01 60.45 70.30 79.55 88.21 94.28 103.58 111.77 118.77 124.50 112.0 4.41

48 043 0.86 1.73 2.59 4.32 8.53 12.29 15.91 19.43 22.85 26.21 29.49 31.76 35.89 40.85 42.08 48.07 53.89 58.14 65.00 75.42 85.13 94.11 100.32 109.65 117.59 124.03

56 0.50 1.01 2.01 3.02 5.40 9.80 14.12 18.27 22.29 26.21 30.03 33.78 36.36 41.06 46.69 48.07 54.84 61.37 66.12 73.73 85.13 95.53 104.84 111.07 119.91

64 0.58 1.15 2.30 3.45 5.75 11.05 15.91 20.58 25.10 29.49 33.78 37.97 40.85 46.09 52.35 53.89 61.37 68.55 73.73 81.98 94.11 104.84 114.07 119.91

72 0.65 1.29 2.59 3.88 6.47 12.29 17.68 22.85 27.86 32.72 37.45 42.08 45.25 51.00 57.86 59.53 67.67 75.42 80.97 89.71 102.29 113.00 121.64

80 0.72 1.44 2.88 4.32 7.19 13.51 19.43 25.10 30.57 35.89 41.06 46.09 49.54 55.79 63.19 65.00 73.73 81.98 87.83 96.92 109.65 119.91

122.2 4.81

142.6 5.61

163.0 6.42

183.3 7.22

203.7 8.02

Conveyor Components

10 20 40 60 100 200 300 400 500 600 700 800 870 1000 1160 1200 1400 1600 1750 2000 2400 2800 3200 3500 4000 4500 5000 5500 PD: MM Inches

HT100 Horsepower Rating–50MM Wide Belt (1.97 in.) No. Teeth

Engineering

RPM Small Sprocket

Operation in shaded area will result in a reduction of belt life.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-29

ENGINEERING/TECHNICAL PAGES PT11- 4


DYNA-SYNC

SELECTION HT100 Basic Horsepower Rating NOTE: Multiply rating by Belt Length Correction Factor from Ratio/Center Distance Tables

14M-40

HT Synchrous Belts Sprockets

RPM Small Sprocket 10 20 40 60 100 200 300 400 500 600 700 800 870 1000 1160 1200 1400 1600 1750 2000 2400 2800 *3200 *3500 PD: MM Inches

28 0.24 0.49 0.97 1.46 2.43 4.87 6.68 8.20 9.59 10.89 12.12 13.28 14 06 15.46 17.09 17.48 19.38 21.18 22.47 24.54 27.78

29 0.25 0.50 1.01 1.51 2.52 5.04 7.01 8.69 10.23 11.68 13.05 14.35 15.22 16.77 18.57 19.01 21.08 23.00 24.36 26.46 29.46 32.17

30 0.26 0.52 1.04 1.56 2.61 5.21 7.39 9.21 10.90 12.49 13.99 15.41 16.37 18.07 20.03 20.51 22.74 24.80 26.23 28.41 31.38 33.75

32 0.28 0.56 1.11 1.67 2.78 5.21 7.31 9.26 11.10 12.85 14.52 16.12 17.20 19.13 21.37 21.91 24.48 26.84 28.47 30.94 34.20 36.58 38.02

124.8 4.91

129.2 5.09

133.7 5.26

142.6 5.61

34 0.31 0.61 1.22 1.83 3.05 6.10 9.15 11.44 13.54 15.52 17.37 19.12 20.30 22.37 24.73 25.29 27.93 30.31 31.92 34.28 37.24 39.15 39.99 39.95 151.5 5.97

14M-55

Conveyor Components Engineering

RPM Small Sprocket 10 20 40 60 100 200 300 400 500 600 700 800 870 1000 1160 1200 1400 1600 1750 2000 2400 2800 *3200 *3500 PD: MM Inches

28 0.35 0.70 1.40 2.10 3.50 7.00 9.61 11.80 13.80 15.67 17.44 19.11 20.24 22.25 24.60 25.16 27.90 30.48 32.34 35.32 39.97

29 0.36 0.73 1.45 2.18 3.63 7.25 10.09 12.50 14.73 16.81 18.78 20.65 21.90 24.14 26.73 27.35 30.33 33.10 35.05 38.08 42.40 46.29

30 0.38 0.75 1.50 2.25 3.75 7.50 10.63 13.25 15.69 17.97 20.13 22.18 23.56 26.01 28.83 29.51 32.73 35.69 37.75 40.89 45.16 48.57

32 0.40 0.80 1.60 2.40 4.00 7.50 10.52 13.32 15.97 18.49 20.89 23.19 24.75 27.52 30.75 31.53 35.22 38.62 40.97 44.53 49.22 52.64 54.71

124.8 4.91

129.2 5.09

133.7 5.26

142.6 5.61

34 0.44 0.88 1.76 2.64 4.39 8.78 13.17 16.46 19.49 22.33 25.00 27.52 29.21 32.19 35.59 36.40 40.20 43.62 45.94 49.34 53.59 56.34 57.55 57.50 151.5 5.97

HT100 Horsepower Rating–40MM Wide Belt (1.57 in.) No. Teeth 36 38 40 44 48 52 56 0.36 0.42 0.50 0.55 0.60 0.65 0.70 0.72 0.84 1.00 1.10 1.20 1.30 1 40 1.44 1.68 2.00 2.20 2.40 2.60 2.80 2.16 2.52 3.00 3.30 3.61 3.91 4.21 3.61 4.20 5.01 5.51 6.01 6.51 7.01 7.21 8.40 9.79 10.75 12.01 13.01 14.01 10.81 12.16 13.16 14.36 17.08 19.50 20.99 14.40 14.96 16.13 17.52 20.58 25.91 25.83 16.91 17.49 18.81 20.36 23.67 29.43 29.52 19.15 19.82 21.27 22.95 26.43 32.49 32.76 21.21 21.97 23.54 25.33 28.93 35.18 35.63 23.14 23.98 25.64 27.52 31.19 37.56 38.16 24.40 25.31 27.02 28.95 32.66 39.05 39.76 26.61 27.61 29.42 31.43 35.14 41.50 42.38 29.07 30.19 32.10 34.15 37.80 43.99 45.03 29.65 30.79 32.72 34.78 38.41 44.53 45.60 32.32 33.58 35.58 47.64 41.07 46.76 47.91 34.64 36.00 38.04 40.02 43.18 48.27 49.36 36.17 37.59 39.63 41.51 44.39 48.94 49.90 38.32 39.80 41.79 43.43 45.76 49.23 49.77 40.76 42.25 44.04 45.04 46.18 47.55 46.88 41.99 43.33 44.74 44.77 44.41 42.01 43.02 43.88 41.28 41.89 160.4 169.3 178.3 196.1 213.9 231.7 249.6 6.32 6.67 7.02 7.72 8.42 9.12 9.82 HT100 Horsepower Rating–55MM Wide Belt (2.17 in.) No. Teeth 36 38 40 44 48 52 56 0.52 0.60 0.72 0.79 0.86 0.94 1.01 1.04 1.21 1.44 1.59 1.73 1.87 2.02 2.08 2.42 2.88 3.17 3.46 3.75 4.04 3.11 3.63 4.32 4.76 5.19 5.62 6.05 5.19 6.05 7.21 7.93 8.65 9.37 10.09 10.38 12.09 14.10 15.47 17.29 18.72 20.16 15.56 17.51 18.94 20.66 24.58 28.06 30.21 20.73 21.52 23.21 25.22 29.62 37.29 37.17 24.34 25.17 27.07 29.31 34.06 42.36 42.49 27.55 28.52 30.61 33.03 38.04 46.76 47.15 30.53 31.62 33.87 36.45 41.63 50.63 51.27 33.29 34.51 36.90 39.60 44.89 54.05 54.92 35.12 36.42 38.89 41.67 47.00 56.19 57.22 38.29 39.73 42.34 45.23 50.57 59.72 60.99 41.84 43.45 46.19 49.15 54.40 63.30 64.80 42.67 44.31 47.09 50.05 55.27 64.08 65.62 46.51 48.33 51.21 54.16 59.11 67.30 68.95 49.85 51.81 54.74 57.59 62.13 69.46 71.04 52.04 54.09 57.02 59.74 63.89 70.43 71.82 55.14 57.28 60.15 62.51 65.85 70.84 71.63 58.65 60.80 63.37 64.81 66.46 68.42 67.46 60.42 62.35 64.39 64.43 63.91 60.45 61.91 63.14 59.40 60.28 160.4 169.3 178.3 196.1 213.9 231.7 249.6 6.32 6.67 7.02 7.72 8.42 9.12 9.82

60 0.75 1.50 3.00 4.51 7.51 15.01 22.49 28.64 32.49 35.81 38.69 41.19 42.74 45.22 47.61 48.10 49.95 50.83 50.86 49.76

64 0.80 1.60 3.20 4.81 8.01 16.01 23.98 29.74 33.67 37.03 39.93 42.42 43.94 46.34 48.56 49.00 50.52 50.96 50.58 48.62

68 0.85 1.70 3.41 5.11 8.51 17.01 25.47 31.26 35.34 38.83 41.81 44.35 45.89 48.26 50.39 50.79 52.03 52.03 51.23 48.34

72 0.90 1.80 3.61 5.41 9.01 18.00 26.96 32.86 37.13 40.75 43.82 46.42 47.98 50.34 52.36 52.72 53.65 53.16 51.86

80 1.04 2.09 4.18 6.27 10.44 20.86 30.54 36.08 40.69 44.56 47.80 50.49 52.06 54.33 56.04 56.29 56.42 54.72

267.4 10.53

285 2 11.23

303.0 11.93

320.9 12.63

356 5 14.04

60 1.08 2.16 4.32 6.49 10.81 21.60 32.36 41.21 46.75 51.53 55.68 59.28 61.51 65.07 68.51 69.22 71.89 73.15 73.20 71.60

64 1.15 2.31 4.61 6.92 11.53 23.04 34.51 42.80 48.45 53.29 57.46 61.04 63.24 66.68 69.89 70.52 72.71 73.33 72.79 69.97

68 1.23 2.45 4.90 7.35 12.25 24.47 36.65 44.98 50.86 55.88 60.17 63.82 66.03 69.45 72.52 73.09 74.88 74.88 73.72 69.57

72 1.30 2.59 5.19 7.78 12.97 25.91 38.79 47.29 53.43 58.64 63.07 66.80 69.04 72.44 75.35 75.87 77.21 76.50 74.64

80 1.50 3.01 6.01 9.02 15.03 30.02 43.95 51.92 58.55 64.13 68.80 72.66 74.91 78.19 80.65 81.00 81.19 78.75

267.4 10.53

285.2 11.23

303.0 11.93

320.9 12.63

356.5 14.04

Operation in shaded area will result in a reduction of belt life. * Operation in this speed range may require sound dampening guard.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-30

ENGINEERING/TECHNICAL PAGES PT11- 4


RPM Small Sprocket 10 20 40 60 100 200 300 400 500 600 700 800 870 1000 1160 1200 1400 1600 1750 *2000 *2400 *2800 *3200 *3500 PD: MM Inches

28 0.58 1.15 2.30 3.46 5.76 11.52 15.80 19.40 22.70 25.78 28.68 31.43 33.29 36.60 40.45 41.39 45.88 50.14 53.20 58.09 65.74

29 0.60 1.19 2.39 3.58 5.97 11.93 16.60 20.56 24.22 27.65 30.88 33.96 36.02 39.70 43.96 44.99 49.88 54.44 57.65 62.63 69.74 76.13

30 0.62 1.23 2.47 3.70 6.17 12.34 17.48 21.80 25.80 29.56 33.11 36.48 38.75 42.77 47.42 48.54 53.83 58.70 62.09 67.25 74.28 79.89

32 0.66 1.32 2.63 3.95 6.58 12.34 17.30 21.91 26.27 30.41 34.36 38.14 40.70 45.27 50.58 51.85 57.93 63.52 67.39 73.23 80.96 86.59 89.98

124.8 4.91

129.2 5.09

133.7 5.26

142.6 5.61

14M-115 RPM Small Sprocket 10 20 40 60 100 200 300 400 500 600 700 800 870 1000 1160 1200 *1400 *1600 *1750 *2000 *2400 *2800 *3200 *3500 PD: MM Inches

28 0.81 1.63 3.26 4.88 8.14 16.27 22.32 27.41 32.07 36.42 40.51 44.41 47.03 51.70 57.15 58.47 64.82 70.83 75.15 82.07 92.88

29 0.84 1.69 3.37 5.06 8.43 16.85 23.45 29.05 34.22 39.06 43.63 47.97 50.89 56.08 62.10 63.55 70.47 76.91 81.44 88.48 98.53 107.6

30 0.87 1.74 3.49 5.23 8.72 17.43 24.70 30.80 36.45 41.76 46.78 51.54 54.74 60.43 66.99 68.57 76.05 82.93 87.71 95.00 104.9 112.9

32 0.93 1.86 3.72 5.58 9.30 17.43 24.44 30.96 37.11 42.95 48.54 53.89 57.50 63.96 71.45 73.26 81.84 89.74 95.21 103.5 114.4 122.3 127.1

124.8 4.91

129.2 5.09

133.7 5.26

142.6 5.61

34 0.72 1.45 2.89 4.34 7.23 14.45 21.66 27.07 32.06 36.72 41.11 45.26 48.04 52.94 58.54 59.87 66.12 71.74 75.55 81.15 88.14 92.66 94.66 94.57 151.5 5.97

HT100 Horsepower Rating–85MM Wide Belt (3.35 in.) No. Teeth 36 38 40 44 48 52 56 0.85 0.99 1.19 1.30 1.42 1.54 1.66 1.71 1.99 2.37 2.61 2.84 3.08 3.32 3.41 3.98 4.74 5.22 5.69 6.16 6.64 5.12 5.97 7.11 7.82 8.53 9.24 9.96 8.54 9.95 11.85 13.04 14.22 15.41 16.59 17.07 19.89 23.18 25.44 28.43 30.80 33.16 25.59 28.79 31.15 33.99 40.42 46.15 49.69 34.09 35.40 38.18 41.48 48.72 61.33 61.13 40.03 41.40 44.53 48.20 56.03 69.66 69.88 45.32 46.91 50.34 54.33 62.56 76.91 77.55 50.21 52.01 55.71 59.95 68.47 83.28 84.33 54.76 56.76 60.69 65.13 73.83 88.89 90.33 57.76 59.90 63.97 68.53 77.30 92.43 94.11 62.98 65.35 69.65 74.39 83.17 98.22 100.3 68.82 71.46 75.97 80.83 89.48 104.1 106.6 70.18 72.89 77.45 82.32 90.91 105.4 107.9 76.49 79.49 84.22 89.08 97.22 110.7 113.4 81.99 85.22 90.03 94.73 102.2 114.2 116.8 85.60 88.97 93.79 98.26 105.1 115.8 118.1 90.69 94.21 98.93 102.8 108.3 116.5 117.8 96.47 100.0 104.2 106.6 109.3 112.5 111.0 99.38 102.5 105.9 106.0 105.1 99.43 101.8 103.9 97.70 99.15 160.4 169.3 178.3 196.1 213.9 231.7 249.6 6.32 6.67 7.02 7.72 8.42 9.12 9.82

60 1.78 3.56 7.11 10.67 17.78 35.52 53.22 67.79 76.90 84.76 91.58 97.50 101.2 107.0 112.7 113.9 118.2 120.3 120.4 117.8

64 1.90 3.79 7.59 11.38 18.96 37.89 56.76 70.40 79.69 87.66 94.51 100.4 104.0 109.7 114.9 116.0 119.6 120.6 119.7 115.1

68 2.02 4.03 8.06 12.09 20.14 40.25 60.28 73.98 83.66 91.91 98.96 105.0 108.6 114.2 119.3 120.2 123.2 123.2 121.2 114.4

72 2.13 4.27 8.53 12.80 21.33 42.61 63.81 77.79 87.89 96.45 103.7 109.9 113.6 119.1 123.9 124.8 127.0 125.8 122.8

80 2.47 4.95 9.89 14.84 24.72 49.38 72.29 85.39 96.31 105.5 113.2 119.5 123.2 128.6 132.6 133.2 133.5 129.5

267.4 10.53

285.2 11.23

303.0 11.93

320.9 12.63

356.5 14.04

64 2.68 5.36 10.72 16.07 26.78 53.53 80.18 99.45 112.6 123.8 133.5 141.8 146.9 154.9 162.4 163.9 168.9 170.4 169.1 162.6

68 2.85 5.69 11.39 17.08 28.46 56.86 85.10 104.5 118.2 129.8 139.8 148.3 153.4 161.4 168.5 169.8 174.0 174.0 171.3 161.6

72 3.01 6.03 12.06 18.08 30.13 60.20 90.14 109.9 124.2 136.3 146.5 155.2 160.4 168.3 175.1 176.3 179.4 177.8 173.4

80 3.49 6.99 13.97 20.96 34.92 69.76 102.1 120.6 136.1 149.0 159.9 168.8 174.1 181.7 187.4 188.2 188.7 183.0

285.2 11.23

303.0 11.93

320.9 12.63

356.5 14.04

HT100 Horsepower Rating–115MM Wide Belt (4.53 in.) No. Teeth 34 36 38 40 44 48 52 56 60 1.02 1.21 1.41 1.67 1.84 2.01 2.18 2.34 2.51 2.04 2.41 2.81 3.35 3.68 4.02 4.35 4.69 5.02 4.08 4.82 5.62 6.70 7.37 8.04 8.71 9.38 10.05 6.12 7.24 8.43 10.05 11.05 12.06 13.06 14.06 15.07 10.21 12.06 14.05 16.74 18.42 20.09 21.76 23.44 25.11 20.41 24.11 28.09 32.75 35.94 40.16 43.51 46.85 50.19 30.60 36.15 40.68 44.00 48.01 57.11 65.20 70.20 75.19 38.25 48.16 50.01 53.93 58.59 68.83 86.65 86.36 95.76 45.29 56.55 58.48 62.90 68.10 79.15 98.42 98.72 108.6 51.88 64.02 66.27 71.12 76.75 88.39 108.7 109.6 119.7 58.08 70.93 73.47 78.70 84.69 96.73 117.6 119.1 129.4 63.95 77.36 80.18 85.73 92.02 104.3 125.6 127.6 137.7 67.87 81.60 84.62 90.37 96.82 109.2 130.6 133.0 142.9 74.79 88.97 92.32 98.39 105.1 117.5 138.8 141.7 151.2 82.69 97.22 100.9 107.3 114.2 126.4 147.1 150.6 159.2 84.57 99.15 103.0 109.4 116.3 128.4 148.9 152.5 160.8 93.41 108.1 112.3 119.0 125.8 137.3 156.4 160.2 167.0 101.4 115.8 120.4 127.2 133.8 144.4 161.4 165.1 170.0 106.7 120.9 125.7 132.5 138.8 148.4 163.7 166.9 170.1 114.6 128.1 133.1 139.8 145.2 153.0 164.6 166.4 166.4 124.5 136.3 141.3 147.3 150.6 154.4 159.0 150.7 130.9 140.4 144.9 149.6 149.7 148.5 133.7 140.5 143.9 146.7 133.6 138.0 140.1 151.5 160.4 169.3 178.3 196.1 213.9 231.7 249.6 267.4 5.97 6.32 6.67 7.02 7.72 8.42 9.12 9.82 10.53

Operation in shaded area will result in a reduction of belt life. * Operation in this speed range may require sound dampening guard. FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-31

ENGINEERING/TECHNICAL PAGES PT11- 4

Sprockets

14M-85

Conveyor Components

NOTE: Multiply rating by Belt Length Correction Factor from Ratio/Center Distance Tables

Engineering

HT100 Basic Horsepower Rating

HT Synchrous Belts

DYNA-SYNC

SELECTION


DYNA-SYNC

SELECTION HT100 Basic Horsepower Rating NOTE: Multiply rating by Belt Length Correction Factor from Ratio/Center Distance Tables

14M-170

HT Synchrous Belts Sprockets

RPM Small Sprocket 10 20 40 60 100 200 300 400 500 600 700 800 870 1000 1160 =1200 =1400 =1600 =1750 =2000 =2400 =2800 =3200 =3500 PD: MM Inches

36 1.89 3.77 7.54 11.31 18.85 37.69 56.51 75.29 88.40 100.1 110.9 120.9 127.6 139.1 152.0 155.0 168.9 181.1 189.0 200.3 213.1 219.5 219.6 215.8 160.4 6.32

38 2.20 4.39 8.79 13.18 21.96 43.92 63.59 78.19 91.43 103.6 114.9 125.3 132.3 144.3 157.8 161.0 175.5 188.2 196.5 208.1 220.8 226.5 224.9 219.0 169.3 6.67

40 2.62 5.24 10.47 15.71 26.17 51.20 68.78 84.31 98.34 111.2 123.0 134.0 141.3 153.8 167.8 171.0 186.0 198.8 207.1 218.5 230.2 233.9 229.4 178.3 7.02

20M-115

Conveyor Components Engineering

RPM Small Sprocket *10 *20 *30 *40 *50 *60 *80 *100 *150 *200 *300 *400 *500 *600 730 800 870 970 1170 =1200 =1460 =1600 =1750 =2000 PD: MM Inches

34 2.7 5.4 8.1 10.7 13.4 16.1 21.5 26.8 40.3 53.7 77.7 97.9 116.7 134.3 155.7 166.6 177.0 191.2 217.0 220.6 248.6 261.3 273.0 288.1 216.45 8.522

36 2.9 5.8 8.7 11.5 14.4 17.3 23.1 28.8 43.2 57.6 83.5 105.0 125.0 143.8 166.5 178.1 189.1 204.0 231.0 234.7 263.5 276.3 287.8 301.8 229.18 9.023

38 3.1 6.1 9.2 12.3 15.3 18.4 24.5 30.7 46.0 61.3 88.7 111.5 132.7 152.5 176.4 188.5 200.0 215.5 243.4 247.3 276.4 289.0 300.0 312.5 241.92 9.524

HT100 Horsepower Rating–170MM Wide Belt (6.69 in.) No. Teeth 44 48 52 56 60 64 2.88 3.14 3.40 3.66 3.93 4.19 5.76 6.28 6.81 7.33 7.85 8.38 11.52 12.56 13.61 14.66 15.71 16.75 17.28 18.85 20.42 21.99 23.56 25.13 28.79 31.41 34.02 36.64 39.26 41.87 56.19 62.79 68.01 73.23 78.46 83.68 75.06 89.27 101.9 109.7 117.5 125.3 91.60 107.6 135.5 135.0 149.7 155.5 106.5 123.7 153.9 154.3 169.8 176.0 120.0 138.2 169.9 171.3 187.2 193.6 132.4 151.2 183.9 186.2 202.2 208.7 143.8 163.1 196.3 199.5 215.3 221.7 151.4 170.7 204.1 207.9 223.4 229.7 164.3 183.7 216.9 221.5 236.4 242.2 178.5 197.6 229.9 235.4 248.9 253.9 181.8 200.8 232.8 238.4 251.4 256.1 196.7 214.7 244.4 250.4 261.1 264.1 209.2 225.7 252.3 258.0 265.7 266.4 217.0 232.1 255.8 260.9 265.9 264.4 227.0 239.2 257.3 260.2 260.1 254.2 235.4 241.4 248.5 245.0 234.0 232.1

68 4.45 8.90 17.80 26.70 44.49 88.89 133.1 163.4 184.8 203.0 218.5 231.8 239.9 252.3 263.4 265.5 272.0 272.0 267.8 252.7

72 4.71 9.42 18.85 28.27 47.10 94.11 140.9 171.8 194.1 213.0 229.1 242.6 250.8 263.1 273.7 275.6 280.4 277.9 271.1

80 5.46 10.92 21.84 32.76 54.59 109.1 159.6 188.6 212.7 232.9 249.9 263.9 272.1 284.0 292.9 294.2 294.9 286.1

196.1 7.72

303.0 11.93

320.9 12.63

356.5 14.04

213.9 8.42

231.7 9.12

249.6 9.82

267.4 10.53

285.2 11.23

HT100 Horsepower Rating–115MM Wide Belt (4.53 in.) No. Teeth 40 44 48 52 56 60 64 68 3.3 3.6 4.0 4.3 4.6 4.9 5.1 5.4 6.5 7.3 7.9 8.6 9.2 9.8 10.3 10.8 9.8 10.9 11.9 12.9 13.8 14.7 15.4 16.2 13.1 14.5 15.8 17.1 18.5 19.5 20.6 21.6 16.3 18.1 19.8 21.4 23.1 24.4 25.7 27.0 19.6 21.8 23.7 25.7 27.7 29.3 30.8 32.4 26.1 29.0 31.6 34.3 36.9 39.1 41.1 43.1 32.6 36.3 39.6 42.8 46.1 48.8 51.4 53.9 48.9 54.4 59.3 64.2 69.2 73.2 77.0 80.8 65.2 72.4 79.0 85.6 92.1 97.4 102.5 107.5 94.3 105.8 117.7 125.4 132.9 140.3 147.5 154.5 118.5 132.7 147.5 156.8 165.9 174.8 183.4 191.8 140.9 157.6 174.8 185.5 195.9 206.0 215.8 225.2 161.8 180.6 200.0 211.9 223.3 234.3 244.8 254.9 186.9 208.2 230.0 242.9 255.2 266.2 277.9 288.2 199.5 221.9 244.8 258.2 270.7 282.5 293.5 303.7 211.6 235.0 258.8 272.4 285.0 296.6 307.5 317.4 227.8 252.4 277.3 272.4 285.0 296.6 307.5 317.4 256.6 282.8 309.0 321.8 332.8 342.0 349.3 354.7 260.5 286.9 313.1 325.6 336.3 345.0 351.7 356.4 289.9 316.3 341.8 350.6 356.5 356.2 358.6 354.5 302.3 327.8 351.7 357.5 359.3 357.2 312.7 336.5 357.9 359.2 355.7 323.4 342.3 357.2 254.65 280.11 305.58 331.04 356.51 381.97 407.44 432.90 10.026 11.028 12.031 13.033 14.036 15.038 16.041 17.043

72 5.6 11.3 16.9 22.6 28.2 33.9 45.1 56.4 84.5 112.5 161.4 200.0 234.3 264.5 297.9 313.1 326.2 326.2 358.0 358.9

80 6.1 12.3 18.4 24.6 30.7 36.8 49.0 61.3 91.8 122.1 174.8 215.8 251.6 282.5 315.3 329.4 340.9 340.9 358.5 357.2

90 6.7 13.4 20.2 26.9 33.6 40.3 53.7 67.1 100.5 133.6 190.8 234.3 271.5 302.5 333.2 345.0 353.4 353.4

458.37 18.046

509.30 20.051

572.96 22.557

Operation in shaded area will result in a reduction of belt life. * Refer to page PT11-20 for additional Service Factors for speeds of 600 RPM or less. = Drives within this speed range may generate an objectionable noise level. This can be reduced by using commercially available acoustical damping material in the belt guard.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-32

ENGINEERING/TECHNICAL PAGES PT11- 4


34 4.2 8.3 12.5 16.7 20.8 25.0 33.4 41.7 62.5 83.3 120.7 152.1 181.2 208.7 242.0 258.9 275.1 297.3 337.7 343.3 387.3 407.5 426.3 450.8 216.45 8.522

36 4.5 9.0 13.4 17.9 22.4 26.9 35.8 44.8 67.2 89.5 129.6 163.1 194.3 223.4 258.8 276.8 293.9 317.2 359.5 365.4 410.7 431.1 449.7 472.8 229.18 9.023

38 4.8 9.5 14.3 19.1 23.8 28.6 38.1 47.6 71.4 95.2 137.8 173.2 206.2 236.9 274.1 293.0 310.9 335.2 379.0 385.0 431.0 451.2 469.1 490.1 241.92 9.524

40 7.0 14.1 21.1 28.1 35.2 42.2 56.3 70.3 105.5 140.6 203.4 255.5 303.9 349.1 403.5 430.9 457.1 492.4 555.6 564.2 629.7 657.8 682.2 709.0 254.65 10.026

HT100 Horsepower Rating–230MM Wide Belt (9.06 in.) No. Teeth 44 48 52 56 60 64 68 72 7.8 8.5 9.2 10.0 10.5 11.1 11.6 12.2 15.6 17.1 18.5 19.9 21.1 22.2 23.3 24.3 23.5 25.6 27.7 29.9 31.6 33.3 34.9 36.5 31.3 34.1 37.0 39.8 42.1 44.3 46.5 48.7 39.1 42.7 46.2 49.8 52.6 55.4 58.1 60.8 46.9 51.2 55.4 59.7 63.2 66.5 69.8 73.0 62.6 68.2 73.9 79.6 84.2 88.6 93.0 97.3 78.2 85.3 92.4 99.5 105.2 110.8 116.2 121.6 117.2 127.9 138.5 149.1 157.7 166.0 174.2 182.2 156.2 170.4 184.5 198.7 210.1 221.1 231.9 242.5 228.2 253.9 270.5 286.7 302.6 318.1 333.3 348.2 286.3 318.1 338.3 358.0 377.1 395.8 414.0 431.8 340.0 377.1 400.4 422.9 444.8 465.9 486.4 506.2 389.8 431.8 457.4 482.4 506.2 529.1 551.1 572.2 449.6 496.8 525.0 551.9 577.4 601.5 624.3 645.7 479.5 529.1 558.3 585.8 611.6 635.9 658.5 679.4 508.0 559.7 589.4 617.2 643.1 667.1 689.0 709.0 546.0 600.2 630.3 657.9 683.2 705.9 726.1 743.8 612.9 670.2 698.9 724.0 745.3 762.8 776.3 785.7 621.9 679.4 707.7 732.1 752.5 768.8 780.9 788.7 688.1 744.8 766.1 781.2 789.9 791.9 787.0 714.8 768.8 784.0 791.4 790.6 736.0 785.4 791.9 788.7 753.7 790.6 280.11 305.58 331.04 356.51 381.97 407.44 432.90 458.37 11.028 12.031 13.033 14.036 15.038 16.041 17.043 18.046

20M-230 RPM Small Sprocket *10 *20 *30 *40 *50 *60 *80 *100 *150 *200 *300 *400 *500 *600 730 800 870 =970 =1170 =1200 =1460 =1600 =1750 =2000 PD: MM Inches

38 6.6 13.2 19.8 26.5 33.1 39.7 52.9 66.1 99.2 132.1 191.3 240.5 286.3 329.1 380.8 406.9 432.0 465.8 526.9 535.3 599.8 628.2 653.6 683.8 241.92 9.524

40 5.1 10.1 15.2 20.3 25.3 30.4 40.5 50.7 76.0 101.2 146.5 184.0 218.8 251.3 290.5 310.2 329.0 354.3 399.6 405.8 452.4 472.3 489.4 507.8 254.65 10.026

HT100 Horsepower Rating–170MM Wide Belt (6.69 in.) No. Teeth 44 48 52 56 60 64 68 5.6 6.1 6.7 7.2 7.6 8.0 8.4 11.3 12.3 13.3 14.3 15.2 16.0 16.8 16.9 18.4 20.0 21.5 22.8 23.9 25.1 22.5 24.6 26.6 28.7 30.3 31.9 33.5 28.2 30.7 33.3 35.8 37.9 39.9 41.9 33.8 36.9 39.9 43.0 45.5 47.9 50.3 45.1 49.1 53.2 57.3 60.7 63.8 67.0 56.3 61.4 66.5 71.7 75.8 79.8 83.7 84.4 92.1 99.7 107.4 113.6 119.6 125.4 112.5 122.7 132.9 143.1 151.3 159.2 167.0 164.4 182.4 194.8 206.5 217.9 229.1 240.0 206.2 229.1 243.6 257.8 271.5 285.0 298.1 244.8 271.5 288.3 304.5 320.2 335.4 350.1 280.7 310.8 329.4 347.2 364.3 380.8 396.6 323.6 357.6 377.8 397.1 415.4 432.7 449.0 345.2 380.8 401.7 421.4 439.9 457.2 473.4 365.5 402.7 424.0 443.9 462.4 479.5 495.1 392.8 431.7 453.2 473.0 490.9 507.1 521.4 440.7 481.7 502.1 519.9 534.9 547.0 556.3 447.1 488.3 508.3 525.6 539.9 551.2 559.4 494.2 534.5 549.3 559.6 565.2 565.8 561.3 512.9 551.2 561.5 566.0 564.5 527.6 562.3 566.2 562.8 539.1 564.5 280.11 305.58 331.04 356.51 381.97 407.44 432.90 11.028 12.031 13.033 14.036 15.038 16.041 17.043

72 8.8 17.5 26.3 35.1 43.8 52.6 70.1 87.6 131.2 174.7 250.7 310.8 364.3 411.7 464.2 488.3 509.3 533.8 562.6 564.4

80 9.5 19.0 28.6 38.1 47.6 57.1 76.1 95.1 142.5 189.6 271.5 335.4 391.4 439.9 491.8 514.4 533.1 552.8 565.8 564.5

90 10.4 20.9 31.3 41.8 52.2 62.6 83.5 104.3 156.1 207.6 296.5 364.3 422.6 471.4 520.5 539.9 554.1

458.37 18.046

509.30 20.051

572.96 22.557

80 13.2 26.4 39.7 52.9 66.1 79.3 105.7 132.1 197.9 263.3 377.1 465.9 543.9 611.6 684.4 716.2 742.8 771.1 791.9 790.6

90 14.5 29.0 43.5 58.0 72.5 87.0 115.9 144.8 216.8 288.3 411.8 506.2 587.4 655.7 724.9 752.5 773.0

509.30 20.051

572.96 22.557

Operation in shaded area will result in a reduction of belt life. * Refer to page PT11-20 for additional Service Factors for speeds of 600 RPM or less. = Drives within this speed range may generate an objectionable noise level. This can be reduced by using commercially available acoustical damping material in the belt guard.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-33

ENGINEERING/TECHNICAL PAGES PT11- 4

Sprockets

RPM Small Sprocket *10 *20 *30 *40 *50 *60 *80 *100 *150 *200 *300 *400 *500 *600 730 800 870 970 1170 =1200 =1460 =1600 =1750 =2000 PD: MM Inches

Conveyor Components

20M-170

Engineering

HT100 Basic Horsepower Rating NOTE: Multiply rating by Belt Length Correction Factor from Ratio/Center Distance Tables

HT Synchrous Belts

DYNA-SYNC

SELECTION


DYNA-SYNC

SELECTION HT100 Basic Horsepower Rating NOTE: Multiply rating by Belt Length Correction Factor from Ratio/Center Distance Tables

20M-290

HT Synchrous Belts Sprockets

RPM Small Sprocket *10 *20 *30 *40 *50 *60 *80 *100 *150 *200 *300 *400 *500 *600 730 800 870 =970 =1170 =1200 =1460 =1600 =1750 =2000 PD: MM Inches

52 11.8 23.7 35.5 47.3 59.1 71.0 94.6 118.2 177.2 236.1 346.2 433.0 512.5 585.7 672.2 714.9 754.8 807.3 895.7 907.0 982.9 1006.5 1017.7

56 12.7 25.5 38.2 50.9 63.7 76.4 101.9 127.3 190.8 254.2 366.9 458.2 541.4 617.5 706.6 750.1 790.6 842.9 928.1 938.5 1002.9 1016.8 1014.6

331.04 13.033

356.51 14.036

20M-340

Conveyor Components Engineering

RPM Small Sprocket *10 *20 *30 *40 *50 *60 *80 *100 *150 *200 *300 *400 *500 *=600 =730 =800 =870 =970 =1170 =1200 =1460 =1600 =1750 =2000 PD: MM Inches

52 14.0 28.0 41.9 55.9 69.9 83.9 111.8 139.8 209.5 279.2 409.3 511.9 605.9 692.5 794.8 845.3 892.7 954.8 1059.7 1073.1 1163.5 1192.0 1205.8

56 15.1 30.1 45.2 60.2 75.3 90.3 120.4 150.5 225.6 300.5 433.8 541.7 640.1 730.1 835.6 887.1 935.0 997.0 1098.2 1110.6 1187.5 1204.6 1202.8

331.04 13.033

356.51 14.036

HT100 Horsepower Rating–290MM Wide Belt (11.42 in.) No. Teeth 60 64 68 72 13.5 14.2 14.9 15.6 27.0 28.4 29.8 31.1 40.4 42.6 44.7 46.7 53.9 56.7 59.5 62.3 67.4 70.9 74.4 77.9 80.8 85.1 89.3 93.4 107.8 113.4 119.0 124.5 134.7 141.8 148.7 155.6 201.9 212.4 222.9 233.2 268.9 282.9 296.8 310.4 387.2 407.1 426.6 445.6 482.7 506.6 529.9 552.7 569.4 596.4 622.7 648.1 648.1 677.5 705.7 732.8 739.3 770.3 799.6 827.1 783.4 814.5 843.6 870.6 823.8 854.6 882.9 908.7 875.4 904.7 930.9 953.8 955.7 978.5 996.3 1008.9 965.1 986.4 1002.4 1012.9 1014.7 1018.0 1016.7

80 16.9 33.8 50.8 67.7 84.6 101.5 135.3 169.0 253.2 336.9 482.7 596.4 696.4 783.4 877.0 918.1 952.4 989.4 1018.0 1016.7

90 18.6 37.1 55.7 74.2 92.7 111.1 148.3 185.3 277.4 368.9 527.1 648.1 752.3 840.1 929.2 965.1 992.0

381.97 15.038

509.30 20.051

572.96 22.557

HT100 Horsepower Rating–340MM Wide Belt (13.39 in.) No. Teeth 60 64 68 72 15.9 16.8 17.6 18.4 31.9 33.5 35.2 36.8 47.8 50.3 52.8 55.2 63.7 67.1 70.4 73.6 79.6 83.8 88.0 92.0 95.6 100.6 105.6 110.4 127.4 134.1 140.7 147.2 159.2 167.6 175.8 184.0 238.7 251.2 263.5 275.6 317.9 334.5 350.8 366.9 457.8 481.3 504.3 526.9 570.7 599.0 626.5 653.4 673.2 705.2 736.3 766.3 766.3 801.1 834.5 866.5 874.3 911.0 945.7 978.3 926.5 963.4 997.8 1029.8 974.4 1010.9 1044.5 1075.1 1035.6 1070.4 1101.5 1128.7 1131.1 1158.3 1179.6 1194.8 1142.2 1167.7 1187.0 1199.8 1202.0 1206.5 1200.6 1205.2

80 20.0 40.0 60.0 80.0 100.0 120.0 159.9 199.8 299.3 398.3 570.7 705.2 823.5 926.5 1037.4 1086.3 1127.2 1171.4 1206.4 1205.2

90 21.9 43.9 65.8 87.7 109.6 131.5 175.3 219.0 328.0 436.2 623.1 766.3 889.7 993.7 1099.5 1142.2 1174.4

381.97 15.038

509.30 20.051

572.96 22.557

407.44 16.041

407.44 16.041

432.90 17.043

458.37 18.046

432.90 17.043

458.37 18.046

Operation in shaded area will result in a reduction of belt life. * Refer to page PT11-20 for additional Service Factors for speeds of 600 RPM or less. = Drives within this speed range may generate an objectionable noise level. This can be reduced by using commercially available acoustical damping material in the belt guard.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-34

ENGINEERING/TECHNICAL PAGES PT11- 4


DYNA-SYNC

SELECTION 5MM Pitch HT200 Belt Drive Selection Table Center Distance, Inches

4 4 04 4 4 42 4 2 44 4 2

4 2

0.86 22 02 4 2 4 2 44 40 4

4 41

4

12

4 4 24 4 42 2 4 41 4 2 44 4 4 4 2 4 40 4 02

2

2

4

4 4

4

42

4

44 4 2 4 40

04

4

44

4 2

4 42 4 2 4 2

1 14

4 12 4 02 4 2 2

22

2 4 21

42 1 2 2 4 12 4 1 0.77 0.81 0.83 0.84 0.86

8005M

900- 1000- 1150- 1300- 1450- 1600- 1720- 21005M 5M 5M 5M 5M 5M 5M 5M

0.88 0.90 0.92 0.94 0.95 0.98 1.00 1.01 1.03 1.06 1.09 1.13 1.16 1.19 1.22 1.24 1 10 11 2 12 0 14 1 4 1 4 22 44 2 40 2 0 1 1 4 1 4 4 10 4 11 42 12 40 14 1 4 1 2 22 24 2 20 2 1 0 1 2 0 2 2 10 24 11 22 12 21 14 1 1 14 1 10 22 0 2 00 2 0 2 12 10 0 0 10 04 11 02 12 01 1 1 4 1 0 21 24 0 2 0 12 4 2 0 1 4 10 11 1 1 1 1 0 21 24 1 2 2 2 4 1 20 4 4 4 10 4 11 42 1 1 1 1 21 2 24 21 2 1 2 4 14 12 1 40 0 0 0 10 04 11 0 12 14 1 2 20 2 2 2 2 14 4 4 2 41 00 10 12 0 14 1 2 20 4 2 4 2 2 4 4 02 1 0 2 2 2 10 24 12 20 14 1 1 1 20 0 2 0 2 2 4 2 21 0 4 11 1 1 1 1 22 4 2 2 4 2 1 0 4 4 4 11 42 1 1 4 1 2 22 2 2 20 2 12 10 0 0 0 11 02 12 1 1 0 21 24 0 2 1 4 4 2 1 10 10 12 0 14 1 2 20 2 2 4 2 4 02 00 2 4 10 11 1 1 1 1 0 21 24 1 2 0 02 22 20 4 1 1 10 14 11 12 12 11 14 0 1 04 1 00 21 24 0 2 0 22 41 0 10 4 11 2 12 1 14 2 1 24 1 20 22 1 2 10 2 0 0 42 4 2 0 10 2 12 1 1 0 21 24 1 2 1 2 10 11 2 12 0 14 4 1 44 1 22 4 2 0 2 2 0 1 4 2 1 0 2 2 2 11 22 1 1 1 14 1 0 22 0 2 00 2 44 02 1 11 1 1 1 4 1 4 22 44 2 2 4 1 4 2 41 10 0 0 0 10 04 12 01 1 1 1 22 4 2 2 1 4 2 21 0 4 4 4 4 10 4 12 40 14 1 2 20 2 2 2 2 1 2 4 4 4 2 1 20 4 10 12 14 1 2 20 2 2 2 2 4 4 1 00 2 2 2 10 24 11 22 1 1 1 1 1 11 21 0 24 02 2 2 4 2 1 40 10 11 2 1 1 1 1 21 4 24 41 2 2 12 10 0 0 10 04 11 02 12 01 1 1 4 1 0 21 24 0 2 0 12 2 0 2 2 10 24 11 22 12 21 14 1 1 14 1 10 22 0 2 00 2 0 2 1 4 1 4 4 10 4 11 42 12 40 14 1 4 1 2 22 24 2 20 2 1 0 1 4 42 11 10 0 0 0 11 02 12 1 1 0 21 24 0 2 1 4 1 0 4 4 4 4 11 41 1 1 4 1 2 22 24 2 1 2 4 2 21 0 4 11 1 1 1 1 22 4 2 2 4 2 01 0 2 2 2 2 10 2 12 20 14 1 1 1 20 0 2 0 2 2 4 2 0 4 0 4 10 11 1 1 1 1 0 21 24 1 2 4 2 2 4 1 41 00 4 10 12 14 1 2 20 4 2 4 2 2 4 22 20 4 1 1 10 14 11 12 12 11 14 0 1 04 1 00 21 24 0 2 0 22 0 4 4 4 10 42 12 40 1 1 0 21 2 24 21 2 41 11 0 0 0 0 10 04 11 02 12 14 1 1 20 2 2 2 2 1 41 0 10 11 2 12 0 14 2 1 24 1 1 22 14 2 10 2 0 0 41 4 2 0 1 4 4 4 10 4 11 42 1 1 1 1 21 2 24 21 2 1 2 4 1 0 2 2 2 2 11 21 1 1 1 14 1 0 22 0 2 00 2 4 41 00 0 4 11 1 1 1 1 4 22 44 2 2 4 2 0 1 4 10 2 11 1 1 1 1 0 21 24 1 2 2 2 4 11 4 1 40 0 0 0 0 10 0 12 00 1 1 1 22 2 2 1 1 2 2 2 10 2 11 22 12 20 14 1 1 14 1 10 22 0 2 00 2 0 2 4 1 20 4 4 4 44 10 4 12 14 1 2 20 2 2 2 2 1 2 4 4 0 10 2 12 1 1 0 21 4 24 40 2 4 2 0 2 4 10 11 1 1 4 1 4 1 40 21 24 1 2 2 2 2 4 0 0 1 4 10 2 12 14 1 1 20 2 2 2 2 4 4 20 4 4 4 4 4 44 11 41 1 1 1 2 22 24 2 1 2 01 2 4 10 2 11 1 1 1 4 1 0 21 24 0 2 0 02 4 2 0 2 2 2 10 2 11 22 1 1 1 1 1 11 21 0 24 02 2 2 4 0 1 11 0 1 1 1 22 2 2 4 2 11 14 1 0 20 2 1 2 0 4 1 4 10 2 11 1 1 1 1 0 21 4 24 41 2 2 2 4 0 4 2 2 2 24 10 2 12 1 14 1 1 12 20 0 2 0 2 2 4 4 4 10 1 12 1 4 1 21 24 0 2 1 4 10 2 12 14 1 1 20 4 2 42 2 2 4 4 41 0 4 10 11 1 1 2 1 2 1 21 21 1 24 11 2 0 2 4 11 0 0 0 10 0 11 02 12 00 1 1 4 1 0 21 24 0 2 0 12 0.88 0.90 0.92 0.94 0.95 0.98 1.00 1.01 1.03 1.06 1.09 1.13 1.16 1.19 1.22 1.24

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-35

ENGINEERING/TECHNICAL PAGES PT11- 4

1.29 1 0 0 40 01 2 22 4 04 4 2 0 0 0

HT Synchrous Belts

1

0.84 4 4 4 41 4 4

7505M

44 0 4 4 24 02 42 1 21 0 0

Sprockets

0.77 0.81 0.83 2 4 42 2 4 40 4 4 2 4 0 44

7005M

4 04 4 0 22 0 40 1 01 4 4 24 40 0 02 42 11 42 04 0 1 4 20 2 4 44 22 1 0 1.29

Conveyor Components

300- 355- 375- 400- 425- 450- 550- 535- 565- 600- 6505M 5M 5M 5M 5M 5M 5M 5M 5M 5M 5M

Engineering

Sprocket Combinations Driver Driven Speed No. Pitch No. Pitch Ratio of Dia. of Dia. teeth In. teeth In. Length Factor* 1 00 2 2 00 2 2 00 1 00 4 21 0 4 21 0 1 00 22 22 1 00 2 1 2 1 1 00 40 2 0 40 2 0 1 00 44 2 44 2 1 00 4 00 4 00 1 00 2 2 2 2 1 00 0 0 1 00 0 0 0 0 1 00 4 4 010 4 4 010 1 00 42 1 42 1 1 04 0 1 2 2 10 2 1 40 2 0 10 22 2 1 10 4 21 0 22 10 4 2 1 2 4 11 10 2 2 00 4 21 0 10 4 4 010 42 1 10 0 0 4 4 010 10 0 0 0 10 2 2 0 10 4 00 2 2 10 44 2 4 00 1 10 40 2 0 44 2 1 11 22 40 2 0 1 12 4 21 0 2 1 11 2 2 00 22 11 4 4 010 2 4 11 11 0 0 42 1 1 14 0 4 4 010 11 2 2 0 0 11 2 1 44 2 11 4 00 0 11 4 2 1 0 40 2 0 11 42 1 0 01 11 44 2 2 2 11 2 2 00 2 1 1 20 40 2 0 4 00 1 20 0 0 2 4 11 1 21 0 42 1 1 22 22 44 2 12 2 2 4 4 010 12 2 2 00 40 2 0 12 4 00 0 0 12 4 4 010 0 01 12 2 1 4 00 12 44 2 0 12 0 2 4 11 12 4 2 1 0 44 2 1 0 40 2 0 2 2 1 1 2 2 42 1 1 2 42 1 0 1 22 4 00 1 4 00 4 4 010 1 0 0 0 01 1 44 2 0 0 1 2 1 2 2 1 2 2 00 44 2 Length Factor*


DYNA-SYNC

SELECTION 5MM Pitch HT200 Belt Drive Selection Table

HT Synchrous Belts Sprockets Conveyor Components Engineering

Sprocket Combinations Driver Driven Speed No. Pitch No. Pitch Ratio of Dia. of Dia. teeth In. teeth In. Length Factor* 1 2 2 2 4 11 1 40 40 2 0 0 1 41 4 4 010 0 1 41 4 21 0 4 00 1 42 4 00 42 1 14 0 0 01 1 44 22 2 2 14 44 2 4 4 010 14 2 1 0 1 0 2 2 00 4 00 1 0 40 2 0 0 0 1 0 4 00 2 4 11 1 0 0 0 0 1 4 21 0 2 2 1 4 2 2 0 01 1 44 2 42 1 1 22 0 1 2 1 0 0 1 0 40 2 0 4 4 010 1 1 0 0 1 2 2 00 2 2 1 4 44 2 2 4 11 1 4 21 0 0 1 4 2 1 112 01 1 22 0 0 1 4 00 0 01 1 2 1 4 4 010 1 0 40 2 0 42 1 1 2 2 0 1 2 2 00 0 1 4 4 010 112 01 1 4 21 0 0 0 1 22 4 4 010 1 2 1 42 1 1 0 40 2 0 2 4 11 1 0 0 1 0 1 2 44 2 0 01 1 0 0 112 01 1 2 2 00 0 0 1 4 00 0 1 4 2 1 0 4 4 010 1 22 42 1 1 0 2 1 2 4 11 2 00 2 2 00 4 4 010 2 00 4 21 0 42 1 2 00 22 2 4 11 2 00 40 2 0 0 01 2 00 0 112 01 20 44 2 0 2 11 2 1 0 01 2 12 4 2 1 0 2 4 11 21 2 2 00 42 1 21 2 2 112 01 2 22 22 0 01 22 2 2 00 2 4 11 22 40 2 0 0 2 4 00 112 01 2 4 21 0 0 01 2 2 1 0 Length Factor*

Center Distance, Inches 300- 355- 375- 400- 425- 450- 550- 535- 565- 600- 650- 7005M 5M 5M 5M 5M 5M 5M 5M 5M 5M 5M 5M

7505M

8005M

900- 1000- 1150- 1300- 1450- 1600- 1720- 21005M 5M 5M 5M 5M 5M 5M 5M

0.77 0.81 0.83 0.84 0.86 0.88 0.90 0.92 0.94 0.95 0.98 1.00 1.01 1.03 1.06 1.09 4 4 4 11 0 1 1 4 11 0 0 0 04 10 0 11 01 12 14 1 1 14 1 10 10 12 0 2 2 2 1 4 1 4 0 4 0 10 2 11 1 1 1 4 40 4 0 0 0 0 10 02 11 1 0 0 0 04 0 11 00 12 1 4 00 4 0 4 1 4 4 44 10 42 11 41 1 1 44 1 4 4 44 4 10 42 12 14 0 4 20 1 4 1 1 14 10 12 11 11 1 0 1 0 01 41 1 4 40 4 0 1 4 10 2 11 0 1 1 4 4 1 4 2 10 1 12 14 4 1 4 2 11 1 2 1 10 2 12 2 10 0 40 4 2 4 10 2 11 0 1 4 1 44 4 4 24 24 2 22 21 11 1 1 1 42 4 2 24 2 22 10 21 12 1 14 1 2 42 2 2 24 2 10 22 11 20 1 1 1 14 4 4 2 4 2 10 1 12 14 4 4 2 10 1 12 14 1 1 0 0 10 4 12 4 1 41 4 4 10 1 11 0 1 1 4 4 04 4 4 4 04 0 02 01 10 00 11 1 4 0 4 10 1 11 0 1 2 1 24 10 4 40 0 04 0 02 10 01 11 00 12 14 4 4 1 42 42 41 41 40 11 1 4 4 0 4 2 1 10 0 12 14 4 4 44 14 4 44 4 42 41 10 40 12 14 4 4 10 12 4 4 44 4 1 44 4 42 10 41 11 1 1 4 1 2 10 2 41 1 44 14 1 12 10 11 11 0 1 0 1 04 4 4 4 4 14 2 2 0 10 12 14 4 4 2 2 1 0 10 4 12 4 14 44 4 21 4 2 2 22 21 21 20 10 1 12 1 14 14 4 10 12 42 4 0 11 1 4 0 10 10 11 10 2 4 24 24 4 2 22 21 10 20 11 1 1 1 1 1 4 4 10 4 12 41 2 4 2 2 2 1 0 10 12 14 0 4 1 2 2 2 1 0 10 12 14 42 00 1 1 0 0 2 10 2 12 2 14 2 0 4 01 02 2 2 01 01 00 10 12 14 4 0 41 01 1 0 0 10 12 14 4 0 40 10 12 14 44 0 11 4 1 2 2 2 2 11 2 01 0 04 04 04 11 0 1 01 4 14 11 1 2 44 1 4 4 4 4 10 4 12 44 14 42 4 4 0 10 12 4 14 2 42 44 4 11 4 4 1 2 4 11 1 1 2 4 2 10 12 14 1 4 44 1 20 21 22 22 11 21 1 1 4 1 11 4 4 0 1 0 04 04 04 10 04 12 02 14 00 4 2 2 2 0 1 1 11 0 1 2 0.77 0.81 0.83 0.84 0.86 0.88 0.90 0.92 0.94 0.95 0.98 1.00 1.01 1.03 1.06 1.09

1.13 1 1 1 1 04 1 0 1 2 1 1 0 1 1 1 01 1 0 1 1 1 2 1 2 1 40 1 12 1 11 1 10 1 0 1 1 1 42 1 0 1 1 1 20 1 1 1 0 1 1 1 0 1 0 1 1 1 2 1 0 1 00 1 0 1 40 1 10 1 0 1 0 14 0 1 0 1 1 1 4 1 1 1 1 1 2 1 14 2 1 1 1 1 14 4 1 1 4 1 1 14 1 1 2 1.13

1.16 1 4 20 1 21 1 1 21 2 20 2 20 21 20 1 1 1 21 1 0 20 0 21 0 20 20 4 1 21 4 1 21 1 1 20 1 2 20 20 2 1 21 2 1 20 20 20 20 0 1 1 4 1 0 21 04 1 20 20 4 20 1 20 4 20 4 20 24 1 4 1 2 1 4 1 4 20 4 20 4 1 42 1 20 4 1 1 1 0 1 1 22 1.16

1.19 22 4 2 2 20 24 1 22 21 4 24 21 2 22 2 1 24 0 2 2 22 21 14 24 1 22 0 2 02 24 01 2 1 2 42 21 24 40 22 2 24 11 1 4 2 1 22 22 2 1 2 21 21 2 24 20 1 2 1 2 1 2 1 2 01 21 2 22 41 20 01 24 00 21 1 2 0 2 41 2 11 2 0 2 0 2 20 22 0 20 20 21 0 22 0 2 0 2 0 20 22 2 22 0 20 22 22 1 1.19

1.22 2 2 2 0 2 4 2 24 2 1 2 1 2 2 2 2 24 0 2 2 24 2 2 2 2 24 2 2 2 2 0 22 2 2 1 2 4 2 1 24 4 2 1 22 2 2 2 2 2 24 2 22 2 24 2 2 2 0 2 2 4 2 1 2 2 1 24 2 2 2 2 2 2 2 2 0 2 4 2 4 2 14 1.22

1.24 2 2 1 2 2 2 2 2 14 2 1 2 2 4 2 2 2 2 2 2 4 2 4 2 2 2 2 4 2 2 0 2 2 2 2 2 14 2 42 24 2 1 2 4 2 2 2 2 2 2 1 2 22 2 2 2 2 4 2 2 4 2 2 2 04 2 02 2 2 2 4 2 12 2 2 2 2 2 2 2 2 2 02 2 2 2 2 2 2 2 12 2 2 2 42 2 1 2 21 2 1 1.24

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-36

ENGINEERING/TECHNICAL PAGES PT11- 4

1.29 2 1 0 4 4 01 02 1 40 41 4 10 4 2 1 1 21 4 14 20 2 0 24 1 0 1 01 4 00 2 4 0 41 11 1 44 22 2 0 4 2 1 21 1 0 0 01 41 0 4 2 1 10 40 22 0 20 4 1 41 0 00 1.29


DYNA-SYNC

SELECTION 5MM Pitch HT200 Belt Drive Selection Table Center Distance, Inches 300- 355- 375- 400- 425- 450- 550- 535- 565- 600- 650- 700- 7505M 5M 5M 5M 5M 5M 5M 5M 5M 5M 5M 5M 5M

8005M

0.77 0.81 0.83 0.84 0.86 0.88 0.90 0.92 0.94 0.95 0.98 1.00 1.01 1.03 40 4 40 11 12 1 1 10 1 4 0 4 40 0 4 42 4 4 4 4 1 4 12 4 0 4 4 00 0 4 2 02 0 11 00 10 1 20 0 1 24 2 0.77 0.81 0.83 0.84 0.86 0.88 0.90 0.92 0.94 0.95 0.98 1.00 1.01 1.03

900- 1000- 1150- 1300- 1450- 1600- 1720- 21005M 5M 5M 5M 5M 5M 5M 5M

1.06 12 11 11 1 11 4 11 10 0 10 1 10 24 10 2 1.06

1.09 14 0 1 11 2 1 4 11 1 12 0 12 1 12 2 12 4 1.09

1.13 1 0 1 14 1 1 44 14 1 4 1 0 1 1 1 2 1 1.13

1.16 20 02 1 2 1 1 41 1 1 0 1 0 1 1 1 24 1 1.16

1.19 22 22 2 20 22 20 4 22 4 21 04 21 1 21 22 21 1 1.19

1.22 2 4 2 24 2 2 2 2 1 2 4 24 00 24 0 24 1 24 2 1.22

1.24 1.29 2 1 0 2 1 10 2 10 0 2 0 1 2 2 2 0 2 2 2 4 2 40 2 41 1.24 1.29

Engineering

Conveyor Components

Sprockets

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special.

HT Synchrous Belts

Sprocket Combinations Spee Driver Driven No. Pitch No. Pitch d Ratio of Dia. of Dia. teeth In. teeth In. Length Factor* 2 0 2 2 00 0 01 2 0 22 0 2 44 2 112 01 2 4 21 0 0 2 0 40 2 0 112 01 2 1 2 2 00 0 2 2 1 112 01 11 22 112 01 2 4 2 1 0 112 01 0 2 2 00 112 01 Length Factor*

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-37

ENGINEERING/TECHNICAL PAGES PT11- 4


DYNA-SYNC

SELECTION 8MM Pitch HT200 Belt Drive Selection Table Speed Ratio

HT Synchrous Belts Sprockets Conveyor Components

1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.05 1.06 1.06 1.06 1.07 1.07 1.08 1.08 1.09 1.09 1.10 1.11 1.11 1.12 1.13 1.13 1.13 1.13 1.14 1.14 1.15 1.16

Sprocket Combinations Driver Driven Pitch Pitch No. of No. of Dia. Dia. teeth teeth Inches Inches Length Factor* 22 2.206 22 2.206 24 2.406 24 2.406 26 2.607 26 2.607 28 2.807 28 2.807 30 3.008 30 3.008 32 3.208 32 3.208 34 3.409 34 3.409 36 3.609 36 3.609 38 3.810 38 3.810 40 4.010 40 4.010 44 4.411 44 4.411 48 4.812 48 4.812 56 5.614 56 5.614 64 6.416 64 6.416 72 7.218 72 7.218 80 8.020 80 8.020 38 3.810 40 4.010 36 3.609 38 3.810 34 3.409 36 3.609 32 3.208 34 3.409 30 3.008 32 3.208 28 2.807 30 3.008 26 2.607 28 2.807 24 2.406 26 2.607 22 2.206 24 2.406 44 4.411 48 4.812 40 4.010 44 4.411 36 3.609 40 4.010 72 7.218 80 8.020 34 3.409 38 3.810 32 3.208 36 3.609 64 6.416 72 7.218 80 8.020 90 9.023 30 3.008 34 3.409 28 2.807 32 3.208 56 5.614 64 6.416 26 2.607 30 3.008 38 3.810 44 4.411 Length Factor*

Center Distance, Inches 3848M

4808M

5608M

6008M

6408M

7208M

8008M

8408M

8808M

9208M

960- 1040- 1064- 1120- 1160- 12008M 8M 8M 8M 8M 8M

0.70 4.09 3.78 3.46 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 3.31 3.62 3.94 ... ... ... ... ... ... ... ... ... ... ... ... ... 0.70

0.80 5.98 5.67 5.35 5.04 4.73 4.41 4.10 ... ... ... ... ... ... ... ... ... ... ... ... 4.25 4.57 4.88 5.20 5.51 5.83 ... ... ... ... ... 4.09 ... ... 4.41 4.72 ... 5.04 ... 0.80

0.80 7.56 7.25 6.93 6.62 6.30 5.99 5.67 5.36 5.04 4.73 ... ... ... ... ... ... 4.88 5.20 5.51 5.83 6.14 6.46 6.77 7.09 7.40 ... ... 5.04 ... 5.35 5.67 ... ... 5.98 6.30 ... 6.61 ... 0.80

0.80 8.34 8.03 7.71 7.40 7.09 6.77 6.46 6.14 5.83 5.51 ... ... ... ... ... ... 5.67 5.98 6.30 6.61 6.93 7.24 7.56 7.87 8.19 ... 5.19 5.82 ... 6.14 6.45 ... ... 6.77 7.08 ... 7.40 5.34 0.80

0.90 9.13 8.82 8.50 8.19 7.88 7.56 7.25 6.93 6.62 6.30 5.67 ... ... ... ... ... 6.46 6.77 7.09 7.40 7.72 8.03 8.35 8.66 8.98 5.35 5.98 6.61 ... 6.93 7.24 ... ... 7.56 7.87 ... 8.19 6.14 0.90

0.90 10.71 10.40 10.08 9.77 9.45 9.14 8.82 8.51 8.19 7.88 7.25 6.62 ... ... ... ... 8.03 8.35 8.66 8.98 9.29 9.61 9.92 10.24 10.55 6.93 7.56 8.19 ... 8.50 8.82 ... ... 9.13 9.45 ... 9.76 7.71 0.90

0.90 12.28 11.97 11.65 11.34 11.03 10.71 10.40 10.08 9.77 9.45 8.82 8.19 6.93 ... ... ... 9.61 9.92 10.24 10.55 10.87 11.18 11.50 11.81 12.13 8.50 9.13 9.76 ... 10.08 10.39 ... ... 10.71 11.02 ... 11.34 9.29 0.90

0.90 13.07 12.76 12.44 12.13 11.81 11.50 11.18 10.87 10.55 10.24 9.61 8.98 7.72 ... ... ... 10.39 10.71 11.02 11.34 11.65 11.97 12.28 12.60 12.91 9.29 9.92 10.55 ... 10.86 11.18 ... ... 11.49 11.81 7.08 12.12 10.07 0.90

0.90 13.86 13.55 13.23 12.92 12.60 12.29 11.97 11.66 11.34 11.03 10.40 9.77 8.51 7.25 ... ... 11.18 11.50 11.81 12.13 12.44 12.76 13.07 13.39 13.70 10.08 10.71 11.34 ... 11.65 11.97 ... ... 12.28 12.60 7.87 12.91 10.86 0.90

1.00 14.64 14.33 14.01 13.70 13.39 13.07 12.76 12.44 12.13 11.81 11.18 10.55 9.29 8.03 ... ... 11.97 12.28 12.60 12.91 13.23 13.54 13.86 14.17 14.49 10.86 11.49 12.12 ... 12.44 12.75 7.39 ... 13.07 13.38 8.65 13.70 11.65 1.00

1.00 15.43 15.12 14.80 14.49 14.18 13.86 13.55 13.23 12.92 12.60 11.97 11.34 10.08 8.82 ... ... 12.76 13.07 13.39 13.70 14.02 14.33 14.65 14.96 15.28 11.65 12.28 12.91 ... 13.23 13.54 8.18 ... 13.86 14.17 9.44 14.49 12.44 1.00

1.00 17.00 16.69 16.37 16.06 15.75 15.43 15.12 14.80 14.49 14.17 13.54 12.91 11.65 10.39 9.13 ... 14.33 14.64 14.96 15.27 15.59 15.90 16.22 16.53 16.85 13.22 13.85 14.48 8.49 14.80 15.11 9.75 ... 15.43 15.74 11.01 16.06 14.01 1.00

1.00 17.48 17.17 16.85 16.54 16.22 15.91 15.59 15.28 14.96 14.65 14.02 13.39 12.13 10.87 9.61 ... 14.80 15.12 15.43 15.75 16.06 16.38 16.69 17.01 17.32 13.70 14.33 14.96 8.97 15.27 15.59 10.23 ... 15.90 16.22 11.49 16.53 14.49 1.00

1.00 18.58 18.27 17.95 17.64 17.32 17.01 16.69 16.38 16.06 15.75 15.12 14.49 13.23 11.97 10.71 9.45 15.90 16.22 16.53 16.85 17.16 17.48 17.79 18.11 18.42 14.80 15.43 16.06 10.07 16.37 16.69 11.33 ... 17.00 17.32 12.59 17.63 15.59 1.00

1.00 19.37 19.06 18.74 18.43 18.11 17.80 17.48 17.17 16.85 16.54 15.91 15.28 14.02 12.76 11.50 10.24 16.69 17.01 17.32 17.64 17.95 18.27 18.58 18.90 19.21 15.59 16.22 16.85 10.86 17.16 17.48 12.12 9.44 17.79 18.11 13.38 18.42 16.38 1.00

1.00 20.15 19.84 19.52 19.21 18.90 18.58 18.27 17.95 17.64 17.32 16.69 16.06 14.80 13.54 12.28 11.02 17.48 17.79 18.11 18.42 18.74 19.05 19.37 19.68 20.00 16.38 17.00 17.63 11.65 17.95 18.26 12.91 10.22 18.58 18.89 14.17 19.21 17.16 1.00

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. Engineering

* This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-38

ENGINEERING/TECHNICAL PAGES PT11- 4


DYNA-SYNC

SELECTION 8MM Pitch HT200 Belt Drive Selection Table Center Distance, Inches

1.10 21.73 21.42 21.10 20.79 20.47 20.16 19.84 19.53 19.21 18.90 18.27 17.64 16.38 15.12 13.86 12.60 19.05 19.37 19.68 20.00 20.31 20.63 20.94 21.26 21.57 17.95 18.58 19.21 13.22 19.52 19.84 14.48 11.80 20.15 20.47 15.74 20.78 18.74 1.10

1.10 24.88 24.57 24.25 23.94 23.62 23.31 22.99 22.68 22.36 22.05 21.42 20.79 19.53 18.27 17.01 15.75 22.20 22.52 22.83 23.15 23.46 23.78 24.09 24.41 24.72 21.10 21.73 22.36 16.37 22.67 22.99 17.63 14.95 23.30 23.62 18.89 23.93 21.89 1.10

1.10 26.30 25.99 25.67 25.36 25.04 24.73 24.41 24.10 23.78 23.47 22.84 22.21 20.95 19.69 18.43 17.17 23.62 23.94 24.25 24.57 24.88 25.20 25.51 25.83 26.14 22.52 23.15 23.78 17.79 24.09 24.41 19.05 16.37 24.72 25.04 20.31 25.35 23.31 1.10

1.10 27.71 27.40 27.08 26.77 26.46 26.14 25.83 25.51 25.20 24.88 24.25 23.62 22.36 21.10 19.84 18.58 25.04 25.35 25.67 25.98 26.30 26.61 26.93 27.24 27.56 23.94 24.57 25.20 19.21 25.51 25.83 20.47 17.79 26.14 26.46 21.73 26.77 24.72 1.10

1.10 28.03 27.72 27.40 27.09 26.77 26.46 26.14 25.83 25.51 25.20 24.57 23.94 22.68 21.42 20.16 18.90 25.35 25.67 25.98 26.30 26.61 26.93 27.24 27.56 27.87 24.25 24.88 25.51 19.52 25.82 26.14 20.78 18.10 26.45 26.77 22.04 27.08 25.04 1.10

1.10 31.18 30.87 30.55 30.24 29.92 29.61 29.29 28.98 28.66 28.35 27.72 27.09 25.83 24.57 23.31 22.05 28.50 28.82 29.13 29.45 29.76 30.08 30.39 30.71 31.02 27.40 28.03 28.66 22.67 28.97 29.29 23.93 21.25 29.60 29.92 25.19 30.23 28.19 1.10

1.20 31.97 31.66 31.34 31.03 30.71 30.40 30.08 29.77 29.45 29.14 28.51 27.88 26.62 25.36 24.10 22.84 29.29 29.61 29.92 30.24 30.55 30.87 31.18 31.50 31.81 28.19 28.82 29.45 23.46 29.76 30.08 24.72 22.04 30.39 30.71 25.98 31.02 28.98 1.20

1.20 35.90 35.59 35.27 34.96 34.65 34.33 34.02 33.70 33.39 33.07 32.44 31.81 30.55 29.29 28.03 26.77 33.23 33.54 33.86 34.17 34.49 34.80 35.12 35.43 35.75 32.13 32.76 33.39 27.40 33.70 34.02 28.66 25.98 34.33 34.65 29.92 34.96 32.91 1.20

1.20 39.84 39.53 39.21 38.90 38.58 38.27 37.95 37.64 37.32 37.01 36.38 35.75 34.49 33.23 31.97 30.71 37.16 37.48 37.79 38.11 38.42 38.74 39.05 39.37 39.68 36.06 36.69 37.32 31.33 37.63 37.95 32.59 29.92 38.26 38.58 33.85 38.89 36.85 1.20

1.20 43.78 43.47 43.15 42.84 42.52 42.21 41.89 41.58 41.26 40.95 40.32 39.69 38.43 37.17 35.91 34.65 41.10 41.42 41.73 42.05 42.36 42.68 42.99 43.31 43.62 40.00 40.63 41.26 35.27 41.57 41.89 36.53 33.86 42.20 42.52 37.79 42.83 40.79 1.20

1.20 47.71 47.40 47.08 46.77 46.46 46.14 45.83 45.51 45.20 44.88 44.25 43.62 42.36 41.10 39.84 38.58 45.04 45.35 45.67 45.98 46.30 46.61 46.93 47.24 47.56 43.94 44.57 45.20 39.21 45.51 45.83 40.47 37.79 46.14 46.46 41.73 46.77 44.72 1.20

1.20 51.65 51.34 51.02 50.71 50.40 50.08 49.77 49.45 49.14 48.82 48.19 47.56 46.30 45.04 43.78 42.52 48.98 49.29 49.61 49.92 50.24 50.55 50.87 51.18 51.50 47.88 48.51 49.14 43.15 49.45 49.77 44.41 41.73 50.08 50.40 45.67 50.71 48.66 1.20

1.20 56.53 56.22 55.90 55.59 55.28 54.96 54.65 54.33 54.02 53.70 53.07 52.44 51.18 49.92 48.66 47.40 53.86 54.17 54.49 54.80 55.12 55.43 55.75 56.06 56.38 52.76 53.39 54.02 48.03 54.33 54.65 49.29 46.61 54.96 55.28 50.55 55.59 53.54 1.20

1.20 61.10 60.79 60.47 60.16 59.84 59.53 59.21 58.90 58.58 58.27 57.64 57.01 55.75 54.49 53.23 51.97 58.42 58.74 59.05 59.37 59.68 60.00 60.31 60.63 60.94 57.32 57.95 58.58 52.60 58.89 59.21 53.86 51.18 59.52 59.84 55.12 60.15 58.11 1.20

1.20 67.40 67.09 66.77 66.46 66.14 65.83 65.51 65.20 64.88 64.57 63.94 63.31 62.05 60.79 59.53 58.27 64.72 65.04 65.35 65.67 65.98 66.30 66.61 66.93 67.24 63.62 64.25 64.88 58.90 65.19 65.51 60.16 57.48 65.82 66.14 61.42 66.45 64.41 1.20

1.20 83.15 82.84 82.52 82.21 81.89 81.58 81.26 80.95 80.63 80.32 79.69 79.06 77.80 76.54 75.28 74.02 80.47 80.79 81.10 81.42 81.73 82.05 82.36 82.68 82.99 79.37 80.00 80.63 74.65 80.94 81.26 75.91 73.23 81.57 81.89 77.17 82.20 80.16 1.20

Sprockets

1.00 20.63 20.32 20.00 19.69 19.37 19.06 18.74 18.43 18.11 17.80 17.17 16.54 15.28 14.02 12.76 11.50 17.95 18.27 18.58 18.90 19.21 19.53 19.84 20.16 20.47 16.85 17.48 18.11 12.12 18.42 18.74 13.38 10.70 19.05 19.37 14.64 19.68 17.64 1.00

HT Synchrous Belts

1224- 1280- 1440- 1512- 1584- 1600- 1760- 1800- 2000- 2200- 2400- 2600- 2800- 3048- 3280- 3600- 44008M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M

Conveyor Components

Sprocket Combinations Driver Driven Speed Ratio No. Pitch No. Pitch of Diam. Dia. of teeth Inches teeth Inches Length Factor* 1.00 22 2.206 22 2.206 1.00 24 2.406 24 2.406 1.00 26 2.607 26 2.607 1.00 28 2.807 28 2.807 1.00 30 3.008 30 3.008 1.00 32 3.208 32 3.208 1.00 34 3.409 34 3.409 1.00 36 3.609 36 3.609 1.00 38 3.810 38 3.810 1.00 40 4.010 40 4.010 1.00 44 4.411 44 4.411 1.00 48 4.812 48 4.812 1.00 56 5.614 56 5.614 1.00 64 6.416 64 6.416 1.00 72 7.218 72 7.218 1.00 80 8.020 80 8.020 1.05 38 3.810 40 4.010 1.06 36 3.609 38 3.810 1.06 34 3.409 36 3.609 1.06 32 3.208 34 3.409 1.07 30 3.008 32 3.208 1.07 28 2.807 30 3.008 1.08 26 2.607 28 2.807 1.08 24 2.406 26 2.607 1.09 22 2.206 24 2.406 1.09 44 4.411 48 4.812 1.10 40 4.010 44 4.411 1.11 36 3.609 40 4.010 1.11 72 7.218 80 8.020 1.12 34 3.409 38 3.810 1.13 32 3.208 36 3.609 1.13 64 6.416 72 7.218 1.13 80 8.020 90 9.023 1.13 30 3.008 34 3.409 1.14 28 2.807 32 3.208 1.14 56 5.614 64 6.416 1.15 26 2.607 30 3.008 1.16 38 3.810 44 4.411 Length Factor*

Engineering

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. * This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-39

ENGINEERING/TECHNICAL PAGES PT11- 4


DYNA-SYNC

SELECTION 8MM Pitch HT200 Belt Drive Selection Table Speed Ratio

HT Synchrous Belts Sprockets Conveyor Components

1.17 1.17 1.18 1.18 1.19 1.20 1.20 1.21 1.22 1.23 1.25 1.25 1.25 1.25 1.26 1.27 1.27 1.27 1.29 1.29 1.29 1.31 1.33 1.33 1.33 1.33 1.36 1.36 1.38 1.39 1.40 1.40 1.41 1.41 1.42 1.43 1.43 1.46

Sprocket Combinations Driver Driven Pitch Pitch No. of No. of Dia. Dia. teeth teeth Inches Inches Length Factor* 24 2.406 28 2.807 48 4.812 56 5.614 34 3.409 40 4.010 22 2.206 26 2.607 32 3.208 38 3.810 30 3.008 36 3.609 40 4.010 48 4.812 28 2.807 34 3.409 36 3.609 44 4.411 26 2.607 32 3.208 24 2.406 30 3.008 32 3.208 40 4.010 64 6.416 80 8.020 72 7.218 90 9.023 38 3.810 48 4.812 30 3.008 38 3.810 22 2.206 28 2.807 44 4.411 56 5.614 28 2.807 36 3.609 56 5.614 72 7.218 34 3.409 44 4.411 26 2.607 34 3.409 24 2.406 32 3.208 30 3.008 40 4.010 36 3.609 48 4.812 48 4.812 64 6.416 28 2.807 38 3.810 22 2.206 30 3.008 32 3.208 44 4.411 26 2.607 36 3.609 40 4.010 56 5.614 80 8.020 112 11.229 64 6.416 90 9.023 34 3.409 48 4.812 24 2.406 34 3.409 28 2.807 40 4.010 56 5.614 80 8.020 22 2.206 32 3.208 Length Factor*

Center Distance, Inches 384- 480- 5608M 8M 8M

6008M

6408M

7208M

8008M

8408M

8808M

9208M

960- 1040- 1064- 1120- 1160- 12008M 8M 8M 8M 8M 8M

0.70 3.46 ... ... 3.77 ... ... ... ... ... ... 3.29 ... ... ... ... ... 3.61 ... ... ... ... ... ... ... ... ... ... 3.44 ... ... ... ... ... ... ... ... ... 3.27 0.70

0.80 7.71 ... 5.98 8.03 6.29 6.61 ... 6.92 5.50 7.24 7.55 6.13 ... ... 5.01 6.44 7.87 ... 6.76 ... 5.65 7.07 7.39 6.28 5.16 ... 6.59 7.70 5.79 6.91 ... ... ... 5.31 7.23 6.43 ... 7.54 0.80

0.90 8.50 ... 6.77 8.82 7.08 7.40 5.66 7.71 6.29 8.03 8.34 6.92 ... ... 5.81 7.23 8.66 ... 7.55 ... 6.44 7.86 8.18 7.07 5.96 ... 7.39 8.50 6.59 7.70 ... ... ... 6.10 8.02 7.22 ... 8.33 0.90

0.90 10.08 5.97 8.34 10.39 8.66 8.97 7.24 9.29 7.87 9.60 9.92 8.50 ... ... 7.39 8.81 10.23 6.27 9.13 ... 8.02 9.44 9.76 8.65 7.54 ... 8.96 10.07 8.17 9.28 6.57 ... ... 7.69 9.59 8.80 ... 9.91 0.90

0.90 11.65 7.55 9.92 11.97 10.23 10.55 8.81 10.86 9.44 11.18 11.49 10.07 ... ... 8.96 10.39 11.81 7.85 10.70 ... 9.60 11.02 11.33 10.23 9.12 6.88 10.54 11.65 9.75 10.86 8.15 ... ... 9.27 11.17 10.38 ... 11.49 0.90

0.90 12.44 8.34 10.70 12.75 11.02 11.33 9.60 11.65 10.23 11.96 12.28 10.86 ... ... 9.75 11.17 12.59 8.64 11.49 ... 10.38 11.80 12.12 11.01 9.90 7.67 11.33 12.43 10.53 11.64 8.94 ... ... 10.05 11.96 11.16 ... 12.27 0.90

0.90 13.23 9.13 11.49 13.54 11.81 12.12 10.39 12.44 11.02 12.75 13.07 11.65 ... ... 10.54 11.96 13.38 9.43 12.28 7.20 11.17 12.59 12.91 11.80 10.69 8.47 12.12 13.22 11.33 12.43 9.73 ... ... 10.85 12.75 11.96 ... 13.06 0.90

1.00 14.01 9.91 12.28 14.33 12.59 12.91 11.17 13.22 11.80 13.54 13.85 12.43 ... ... 11.33 12.75 14.17 10.22 13.06 7.99 11.96 13.38 13.69 12.59 11.48 9.26 12.90 14.01 12.11 13.22 10.52 ... ... 11.63 13.53 12.74 ... 13.85 1.00

1.00 14.80 10.70 13.07 15.12 13.38 13.70 11.96 14.01 12.59 14.33 14.64 13.22 ... ... 12.12 13.54 14.96 11.01 13.86 8.79 12.75 14.17 14.49 13.38 12.27 10.05 13.69 14.80 12.90 14.01 11.31 ... ... 12.42 14.32 13.53 8.10 14.64 1.00

0.80 5.35 ... ... 5.67 ... 4.24 ... 4.56 ... 4.87 5.19 ... ... ... ... 4.08 5.50 ... 4.39 ... ... 4.71 5.02 ... ... ... 4.22 5.34 ... 4.54 ... ... ... ... 4.86 4.05 ... 5.17 0.80

0.80 6.93 ... 5.19 7.24 5.50 5.82 ... 6.14 4.71 6.45 6.77 5.34 ... ... ... 5.66 7.08 ... 5.97 ... 4.86 6.29 6.60 5.49 ... ... 5.81 6.92 5.00 6.12 ... ... ... ... 6.44 5.64 ... 6.75 0.80

1.00 16.37 12.27 14.64 16.69 14.96 15.27 13.54 15.59 14.17 15.90 16.22 14.80 9.10 ... 13.69 15.11 16.53 12.58 15.43 10.36 14.32 15.74 16.06 14.95 13.84 11.62 15.26 16.37 14.47 15.58 12.89 ... 8.24 14.00 15.89 15.10 9.69 16.21 1.00

1.00 16.85 12.75 15.12 17.16 15.43 15.75 14.01 16.06 14.64 16.38 16.69 15.27 9.57 ... 14.16 15.58 17.01 13.06 15.90 10.84 14.79 16.22 16.53 15.42 14.32 12.10 15.74 16.85 14.95 16.06 13.36 ... 8.72 14.47 16.37 15.58 10.17 16.69 1.00

1.00 17.95 13.85 16.22 18.26 16.53 16.85 15.11 17.16 15.74 17.48 17.79 16.37 10.68 9.25 15.27 16.69 18.11 14.16 17.00 11.94 15.90 17.32 17.63 16.53 15.42 13.20 16.84 17.95 16.05 17.16 14.46 ... 9.83 15.57 17.47 16.68 11.27 17.79 1.00

1.00 18.74 14.64 17.01 19.05 17.32 17.64 15.90 17.95 16.53 18.27 18.58 17.16 11.47 10.04 16.06 17.48 18.90 14.95 17.79 12.73 16.69 18.11 18.42 17.32 16.21 13.99 17.63 18.74 16.84 17.95 15.26 ... 10.63 16.36 18.26 17.47 12.07 18.58 1.00

1.00 19.52 15.43 17.79 19.84 18.11 18.42 16.69 18.74 17.32 19.05 19.37 17.95 12.26 10.83 16.84 18.26 19.68 15.73 18.58 13.52 17.47 18.89 19.21 18.10 17.00 14.78 18.42 19.52 17.63 18.73 16.04 ... 11.42 17.15 19.05 18.26 12.86 19.36 1.00

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. Engineering

* This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-40

ENGINEERING/TECHNICAL PAGES PT11- 4


DYNA-SYNC

SELECTION 8MM Pitch HT200 Belt Drive Selection Table Center Distance, Inches

1.10 21.10 17.00 19.37 21.41 19.68 20.00 18.26 20.31 18.89 20.63 20.94 19.52 13.83 12.41 18.42 19.84 21.26 17.31 20.15 15.10 19.05 20.47 20.78 19.68 18.57 16.36 19.99 21.10 19.20 20.31 17.62 9.95 13.00 18.73 20.62 19.83 14.44 20.94 1.10

1.10 24.25 20.15 22.52 24.56 22.83 23.15 21.41 23.46 22.04 23.78 24.09 22.67 16.99 15.56 21.57 22.99 24.41 20.46 23.30 18.25 22.20 23.62 23.93 22.83 21.72 19.51 23.14 24.25 22.35 23.46 20.77 13.13 16.17 21.88 23.77 22.98 17.60 24.09 1.10

1.10 25.67 21.57 23.94 25.98 24.25 24.57 22.83 24.88 23.46 25.20 25.51 24.09 18.41 16.99 22.99 24.41 25.83 21.88 24.72 19.67 23.62 25.04 25.35 24.25 23.14 20.93 24.56 25.67 23.77 24.88 22.19 14.56 17.59 23.30 25.19 24.40 19.02 25.51 1.10

1.10 27.08 22.99 25.35 27.40 25.67 25.98 24.25 26.30 24.88 26.61 26.93 25.51 19.83 18.40 24.40 25.82 27.24 23.30 26.14 21.09 25.03 26.45 26.77 25.66 24.56 22.35 25.98 27.08 25.19 26.29 23.61 15.98 19.01 24.71 26.61 25.82 20.44 26.92 1.10

1.10 27.40 23.30 25.67 27.71 25.98 26.30 24.56 26.61 25.19 26.93 27.24 25.82 20.14 18.72 24.72 26.14 27.56 23.61 26.45 21.40 25.35 26.77 27.08 25.98 24.87 22.66 26.29 27.40 25.50 26.61 23.92 16.30 19.33 25.03 26.92 26.13 20.75 27.24 1.10

1.10 30.55 26.45 28.82 30.86 29.13 29.45 27.71 29.76 28.34 30.08 30.39 28.97 23.29 21.87 27.87 29.29 30.71 26.76 29.60 24.55 28.50 29.92 30.23 29.13 28.02 25.81 29.44 30.55 28.65 29.76 27.07 19.46 22.48 28.18 30.07 29.28 23.91 30.39 1.10

1.20 31.34 27.24 29.61 31.65 29.92 30.24 28.50 30.55 29.13 30.87 31.18 29.76 24.08 22.66 28.66 30.08 31.50 27.55 30.39 25.34 29.29 30.71 31.02 29.92 28.81 26.60 30.23 31.34 29.44 30.55 27.86 20.25 23.27 28.97 30.86 30.07 24.70 31.18 1.20

1.20 35.28 31.18 33.54 35.59 33.86 34.17 32.44 34.49 33.07 34.80 35.12 33.70 28.02 26.60 32.59 34.01 35.43 31.49 34.33 29.28 33.22 34.64 34.96 33.85 32.75 30.54 34.17 35.27 33.38 34.48 31.80 24.20 27.21 32.91 34.80 34.01 28.64 35.11 1.20

1.20 39.21 35.11 37.48 39.52 37.79 38.11 36.37 38.42 37.00 38.74 39.05 37.63 31.96 30.54 36.53 37.95 39.37 35.43 38.26 33.22 37.16 38.58 38.89 37.79 36.69 34.48 38.10 39.21 37.32 38.42 35.74 28.14 31.15 36.84 38.73 37.95 32.57 39.05 1.20

1.20 43.15 39.05 41.42 43.46 41.73 42.05 40.31 42.36 40.94 42.68 42.99 41.57 35.90 34.48 40.47 41.89 43.31 39.37 42.20 37.16 41.10 42.52 42.83 41.73 40.63 38.42 42.05 43.15 41.26 42.36 39.68 32.09 35.10 40.78 42.67 41.89 36.52 42.99 1.20

1.20 47.09 42.99 45.35 47.40 45.67 45.98 44.25 46.30 44.88 46.61 46.93 45.51 39.83 38.41 44.41 45.82 47.24 43.30 46.14 41.09 45.04 46.45 46.77 45.67 44.56 42.35 45.98 47.08 45.19 46.30 43.61 36.03 39.03 44.72 46.61 45.82 40.45 46.93 1.20

1.20 51.03 46.93 49.29 51.34 49.61 49.92 48.19 50.24 48.82 50.55 50.87 49.45 43.77 42.35 48.35 49.76 51.18 47.24 50.08 45.03 48.98 50.39 50.71 49.61 48.50 46.29 49.92 51.02 49.13 50.24 47.55 39.97 42.97 48.66 50.55 49.76 44.40 50.87 1.20

1.20 55.91 51.81 54.17 56.22 54.49 54.80 53.07 55.12 53.70 55.43 55.75 54.33 48.66 47.24 53.23 54.64 56.06 52.12 54.96 49.92 53.86 55.27 55.59 54.49 53.38 51.18 54.80 55.90 54.01 55.12 52.44 44.85 47.86 53.54 55.43 54.64 49.28 55.75 1.20

1.20 60.47 56.38 58.74 60.78 59.05 59.37 57.63 59.68 58.26 60.00 60.31 58.89 53.22 51.80 57.79 59.21 60.63 56.69 59.52 54.48 58.42 59.84 60.15 59.05 57.95 55.74 59.37 60.47 58.58 59.68 57.00 49.42 52.42 58.10 60.00 59.21 53.84 60.31 1.20

1.20 66.77 62.68 65.04 67.08 65.35 65.67 63.93 65.98 64.56 66.30 66.61 65.19 59.52 58.10 64.09 65.51 66.93 62.99 65.82 60.78 64.72 66.14 66.45 65.35 64.25 62.04 65.67 66.77 64.88 65.98 63.30 55.72 58.72 64.40 66.30 65.51 60.14 66.61 1.20

1.20 82.52 78.43 80.79 82.83 81.10 81.42 79.69 81.73 80.32 82.05 82.36 80.95 75.27 73.85 79.84 81.26 82.68 78.74 81.57 76.53 80.47 81.89 82.20 81.10 80.00 77.79 81.42 82.52 80.63 81.73 79.05 71.48 74.48 80.16 82.05 81.26 75.90 82.36 1.20

Sprockets

1.00 20.00 15.90 18.27 20.31 18.58 18.90 17.16 19.21 17.79 19.53 19.84 18.42 12.73 11.30 17.32 18.74 20.16 16.21 19.05 13.99 17.95 19.37 19.68 18.58 17.47 15.26 18.89 20.00 18.10 19.21 16.52 ... 11.90 17.62 19.52 18.73 13.33 19.84 1.00

HT Synchrous Belts

1224- 1280- 1440- 1512- 1584- 1600- 1760- 1800- 2000- 2200- 2400- 2600- 2800- 3048- 3280- 3600- 44008M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M

Conveyor Components

Sprocket Combinations Driver Driven Speed Ratio No. Pitch No. Pitch Diam. of Dia. of teeth Inches teeth Inches Length Factor* 1.17 24 2.406 28 2.807 1.17 48 4.812 56 5.614 1.18 34 3.409 40 4.010 1.18 22 2.206 26 2.607 1.19 32 3.208 38 3.810 1.20 30 3.008 36 3.609 1.20 40 4.010 48 4.812 1.21 28 2.807 34 3.409 1.22 36 3.609 44 4.411 1.23 26 2.607 32 3.208 1.25 24 2.406 30 3.008 1.25 32 3.208 40 4.010 1.25 64 6.416 80 8.020 1.25 72 7.218 90 9.023 1.26 38 3.810 48 4.812 1.27 30 3.008 38 3.810 1.27 22 2.206 28 2.807 1.27 44 4.411 56 5.614 1.29 28 2.807 36 3.609 1.29 56 5.614 72 7.218 1.29 34 3.409 44 4.411 1.31 26 2.607 34 3.409 1.33 24 2.406 32 3.208 1.33 30 3.008 40 4.010 1.33 36 3.609 48 4.812 1.33 48 4.812 64 6.416 1.36 28 2.807 38 3.810 1.36 22 2.206 30 3.008 1.38 32 3.208 44 4.411 1.39 26 2.607 36 3.609 1.40 40 4.010 56 5.614 1.40 80 8.020 112 11.229 1.41 64 6.416 90 9.023 1.41 34 3.409 48 4.812 1.42 24 2.406 34 3.409 1.43 28 2.807 40 4.010 1.43 56 5.614 80 8.020 1.46 22 2.206 32 3.208 Length Factor*

Engineering

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. * This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-41

ENGINEERING/TECHNICAL PAGES PT11- 4


DYNA-SYNC

SELECTION 8MM Pitch HT200 Belt Drive Selection Table Speed Ratio

HT Synchrous Belts Sprockets Conveyor Components

1.46 1.46 1.47 1.47 1.50 1.50 1.50 1.54 1.55 1.56 1.56 1.57 1.58 1.60 1.60 1.61 1.64 1.64 1.65 1.67 1.67 1.68 1.69 1.71 1.73 1.75 1.75 1.78 1.80 1.80 1.82 1.82 1.83 1.85 1.87 1.88 1.88 1.90

Sprocket Combinations Driver Driven Pitch Pitch No. of No. of Dia. Dia. teeth teeth Inches Inches Length Factor* 44 4.411 64 6.416 26 2.607 38 3.810 30 3.008 44 4.411 38 3.810 56 5.614 24 2.406 36 3.609 32 3.208 48 4.812 48 4.812 72 7.218 26 2.607 40 4.010 22 2.206 34 3.409 36 3.609 56 5.614 72 7.218 112 11.229 28 2.807 44 4.411 24 2.406 38 3.810 30 3.008 48 4.812 40 4.010 64 6.416 56 5.614 90 9.023 22 2.206 36 3.609 44 4.411 72 7.218 34 3.409 56 5.614 24 2.406 40 4.010 48 4.812 80 8.020 38 3.810 64 6.416 26 2.607 44 4.411 28 2.807 48 4.812 22 2.206 38 3.810 32 3.208 56 5.614 64 6.416 112 11.229 36 3.609 64 6.416 40 4.010 72 7.218 80 8.020 144 14.437 22 2.206 40 4.010 44 4.411 80 8.020 24 2.406 44 4.411 26 2.607 48 4.812 30 3.008 56 5.614 48 4.812 90 9.023 34 3.409 64 6.416 38 3.810 72 7.218 Length Factor*

Center Distance, Inches 4808M

5608M

6008M

6408M

7208M

8008M

8408M

8808M

9208M

9608M

1040- 1064- 1120- 1160- 12008M 8M 8M 8M 8M

0.80 ... 4.37 ... ... 4.69 ... ... 4.19 5.00 ... ... ... 4.51 ... ... ... 4.83 ... ... 4.34 ... ... ... ... 4.66 ... ... ... ... ... 4.48 ... 3.97 ... ... ... ... ... 0.80

0.80 ... 5.95 5.15 ... 6.27 4.66 ... 5.79 6.59 ... ... 5.30 6.10 4.80 ... ... 6.42 ... ... 5.93 ... ... 5.44 4.94 6.25 ... ... ... ... ... 6.08 ... 5.58 5.08 ... ... ... ... 0.80

0.80 ... 6.74 5.94 ... 7.06 5.45 ... 6.58 7.38 ... ... 6.09 6.89 5.60 ... ... 7.21 ... ... 6.72 ... ... 6.23 5.74 7.04 ... ... ... ... ... 6.87 ... 6.38 5.88 4.86 ... ... ... 0.80

0.90 ... 7.54 6.74 ... 7.85 6.25 ... 7.37 8.17 5.26 ... 6.88 7.69 6.39 ... ... 8.00 ... 5.40 7.52 ... ... 7.03 6.54 7.83 5.54 ... ... ... ... 7.66 ... 7.18 6.68 5.68 ... ... ... 0.90

0.90 ... 9.12 8.32 6.71 9.43 7.84 ... 8.95 9.75 6.86 ... 8.47 9.27 7.98 5.86 ... 9.58 ... 7.00 9.10 ... 6.00 8.62 8.13 9.42 7.14 ... 6.14 ... ... 9.25 ... 8.76 8.27 7.29 ... 6.28 ... 0.90

0.90 7.18 10.69 9.90 8.30 11.01 9.42 ... 10.53 11.32 8.45 ... 10.05 10.85 9.57 7.46 ... 11.16 6.46 8.59 10.68 ... 7.61 10.20 9.71 11.00 8.74 ... 7.75 6.74 ... 10.83 ... 10.35 9.86 8.88 ... 7.89 6.88 0.90

0.90 7.97 11.48 10.69 9.09 11.80 10.20 6.98 11.32 12.11 9.24 ... 10.84 11.63 10.35 8.26 ... 11.95 7.27 9.38 11.47 ... 8.40 10.99 10.50 11.78 9.53 ... 8.55 7.55 ... 11.62 ... 11.14 10.65 9.68 ... 8.69 7.68 0.90

0.90 8.76 12.27 11.48 9.88 12.59 11.00 7.78 12.11 12.90 10.03 ... 11.63 12.42 11.15 9.06 ... 12.74 8.07 10.18 12.26 7.06 9.20 11.78 11.30 12.57 10.33 ... 9.35 8.35 ... 12.41 7.34 11.93 11.44 10.47 ... 9.49 8.49 0.90

1.00 9.55 13.06 12.26 10.67 13.37 11.78 8.58 12.89 13.69 10.82 ... 12.42 13.21 11.93 9.85 ... 13.52 8.87 10.97 13.05 7.87 9.99 12.57 12.08 13.36 11.12 ... 10.14 9.15 ... 13.20 8.15 12.72 12.23 11.26 ... 10.28 9.29 1.00

1.00 10.35 13.85 13.05 11.46 14.16 12.58 9.37 13.69 14.48 11.61 ... 13.21 14.00 12.73 10.64 ... 14.32 9.66 11.76 13.84 8.67 10.79 13.36 12.88 14.15 11.91 ... 10.94 9.95 ... 13.99 8.95 13.51 13.03 12.06 7.75 11.08 10.09 1.00

1.00 11.92 15.42 14.63 13.04 15.73 14.15 10.96 15.26 16.05 13.19 ... 14.78 15.57 14.30 12.22 8.81 15.89 11.25 13.34 15.41 10.27 12.37 14.93 14.45 15.72 13.49 ... 12.52 11.54 ... 15.56 10.55 15.08 14.60 13.64 9.37 12.66 11.68 1.00

1.00 12.40 15.89 15.10 13.51 16.21 14.62 11.43 15.73 16.52 13.66 ... 15.25 16.05 14.78 12.70 9.29 16.36 11.73 13.81 15.89 10.75 12.85 15.41 14.93 16.20 13.96 ... 13.00 12.02 ... 16.04 11.03 15.56 15.08 14.11 9.85 13.14 12.16 1.00

1.00 13.50 16.99 16.20 14.62 17.31 15.73 12.54 16.83 17.62 14.77 ... 16.36 17.15 15.88 13.80 10.41 17.46 12.83 14.92 16.99 11.86 13.95 16.51 16.03 17.30 15.07 ... 14.10 13.13 ... 17.14 12.15 16.66 16.18 15.22 10.98 14.25 13.27 1.00

1.00 14.30 17.78 16.99 15.41 18.10 16.52 13.33 17.62 18.42 15.56 ... 17.15 17.94 16.67 14.60 11.21 18.25 13.63 15.71 17.78 12.65 14.75 17.30 16.82 18.09 15.86 ... 14.90 13.92 ... 17.93 12.95 17.45 16.97 16.01 11.78 15.04 14.07 1.00

1.00 15.08 18.57 17.78 16.19 18.89 17.30 14.12 18.41 19.20 16.35 ... 17.93 18.72 17.45 15.38 12.00 19.04 14.42 16.50 18.56 13.45 15.53 18.09 17.61 18.88 16.65 9.45 15.68 14.71 ... 18.72 13.74 18.24 17.76 16.80 12.58 15.83 14.86 1.00

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. Engineering

* This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-42

ENGINEERING/TECHNICAL PAGES PT11- 4


DYNA-SYNC

SELECTION 8MM Pitch HT200 Belt Drive Selection Table Center Distance, Inches

1.10 16.66 20.15 19.36 17.77 20.46 18.88 15.70 19.99 20.78 17.92 10.51 19.51 20.30 19.03 16.96 13.59 20.62 16.00 18.07 20.14 15.03 17.11 19.66 19.18 20.45 18.23 11.07 17.26 16.30 ... 20.29 15.33 19.82 19.34 18.38 14.17 17.41 16.45 1.10

1.10 19.82 23.30 22.51 20.92 23.61 22.03 18.86 23.14 23.93 21.08 13.71 22.66 23.45 22.18 20.12 16.76 23.77 19.16 21.23 23.29 18.20 20.27 22.82 22.34 23.61 21.38 14.28 20.42 19.46 ... 23.45 18.49 22.97 22.49 21.53 17.35 20.57 19.61 1.10

1.10 21.24 24.72 23.93 22.35 25.03 23.45 20.28 24.56 25.35 22.50 15.14 24.08 24.87 23.61 21.54 18.19 25.19 20.58 22.65 24.71 19.62 21.69 24.24 23.76 25.03 22.80 15.72 21.85 20.88 11.68 24.87 19.92 24.39 23.91 22.96 18.78 22.00 21.03 1.10

1.10 22.65 26.13 25.34 23.76 26.45 24.87 21.70 25.97 26.76 23.92 16.57 25.50 26.29 25.02 22.96 19.61 26.60 22.00 24.07 26.13 21.04 23.11 25.65 25.18 26.44 24.22 17.15 23.26 22.30 13.15 26.28 21.34 25.81 25.33 24.37 20.20 23.42 22.45 1.10

1.10 22.97 26.45 25.66 24.08 26.76 25.18 22.01 26.29 27.08 24.23 16.89 25.81 26.60 25.34 23.28 19.93 26.92 22.32 24.38 26.44 21.36 23.43 25.97 25.49 26.76 24.54 17.47 23.58 22.62 13.47 26.60 21.66 26.12 25.64 24.69 20.52 23.73 22.77 1.10

1.10 26.12 29.60 28.81 27.23 29.91 28.33 25.17 29.44 30.23 27.38 20.06 28.96 29.75 28.49 26.43 23.09 30.07 25.47 27.54 29.60 24.51 26.58 29.12 28.64 29.91 27.69 20.65 26.73 25.78 16.70 29.75 24.82 29.27 28.80 27.84 23.69 26.89 25.93 1.10

1.20 26.91 30.39 29.60 28.02 30.70 29.13 25.96 30.23 31.02 28.17 20.85 29.76 30.54 29.28 27.22 23.88 30.86 26.26 28.33 30.39 25.31 27.37 29.91 29.43 30.70 28.48 21.44 27.53 26.57 17.50 30.54 25.61 30.06 29.59 28.63 24.48 27.68 26.72 1.20

1.20 30.85 34.32 33.54 31.96 34.64 33.06 29.90 34.17 34.95 32.11 24.80 33.69 34.48 33.22 31.16 27.82 34.80 30.20 32.26 34.32 29.25 31.31 33.85 33.37 34.64 32.42 25.40 31.47 30.51 21.49 34.48 29.55 34.00 33.53 32.57 28.43 31.62 30.66 1.20

1.20 34.79 38.26 37.47 35.89 38.58 37.00 33.84 38.10 38.89 36.05 28.75 37.63 38.42 37.15 35.10 31.76 38.73 34.14 36.20 38.26 33.19 35.25 37.78 37.31 38.57 36.36 29.35 35.40 34.45 25.46 38.41 33.49 37.94 37.46 36.51 32.37 35.56 34.60 1.20

1.20 38.73 42.20 41.41 39.83 42.52 40.94 37.78 42.04 42.83 39.99 32.70 41.57 42.36 41.09 39.04 35.71 42.67 38.09 40.14 42.20 37.13 39.19 41.72 41.25 42.51 40.30 33.30 39.35 38.39 29.43 42.35 37.44 41.88 41.40 40.45 36.32 39.50 38.55 1.20

1.20 42.66 46.14 45.35 43.77 46.45 44.87 41.71 45.98 46.77 43.92 36.64 45.50 46.29 45.03 42.97 39.65 46.61 42.02 44.08 46.13 41.07 43.13 45.66 45.18 46.45 44.23 37.24 43.28 42.33 33.39 46.29 41.38 45.81 45.34 44.39 40.26 43.44 42.48 1.20

1.20 46.61 50.08 49.29 47.71 50.39 48.81 45.66 49.92 50.71 47.87 40.58 49.44 50.23 48.97 46.92 43.59 50.55 45.97 48.02 50.07 45.01 47.07 49.60 49.13 50.39 48.18 41.19 47.23 46.27 37.34 50.23 45.32 49.76 49.28 48.33 44.20 47.38 46.43 1.20

1.20 51.49 54.96 54.17 52.59 55.27 53.70 50.54 54.80 55.59 52.75 45.47 54.33 55.11 53.85 51.80 48.47 55.43 50.85 52.90 54.96 49.90 51.95 54.48 54.01 55.27 53.06 46.08 52.11 51.16 42.24 55.11 50.20 54.64 54.16 53.21 49.09 52.26 51.31 1.20

1.20 56.05 59.52 58.73 57.16 59.84 58.26 55.10 59.36 60.15 57.31 50.04 58.89 59.68 58.42 56.36 53.04 59.99 55.41 57.47 59.52 54.46 56.52 59.05 58.57 59.83 57.62 50.65 56.67 55.72 46.82 59.68 54.77 59.20 58.73 57.78 53.66 56.83 55.88 1.20

1.20 62.35 65.82 65.03 63.46 66.14 64.56 61.40 65.66 66.45 63.61 56.34 65.19 65.98 64.72 62.66 59.34 66.29 61.72 63.77 65.82 60.77 62.82 65.35 64.87 66.14 63.92 56.96 62.98 62.03 53.13 65.98 61.08 65.50 65.03 64.08 59.96 63.13 62.18 1.20

1.20 78.11 81.57 80.79 79.21 81.89 80.31 77.16 81.41 82.20 79.36 72.10 80.94 81.73 80.47 78.42 75.10 82.04 77.47 79.52 81.57 76.52 78.57 81.10 80.62 81.89 79.68 72.72 78.73 77.78 68.90 81.73 76.83 81.25 80.78 79.83 75.72 78.88 77.94 1.20

Sprockets

1.00 15.56 19.05 18.25 16.67 19.36 17.78 14.60 18.88 19.68 16.82 ... 18.41 19.20 17.93 15.86 12.48 19.52 14.90 16.97 19.04 13.92 16.01 18.56 18.08 19.35 17.12 9.94 16.16 15.19 ... 19.19 14.22 18.71 18.23 17.27 13.06 16.31 15.34 1.00

HT Synchrous Belts

1224- 1280- 1440- 1512- 1584- 1600- 1760- 1800- 2000- 2200- 2400- 2600- 2800- 3048- 3280- 3600- 44008M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M

Conveyor Components

Sprocket Combinations Driver Driven Speed Ratio No. Pitch No. Pitch of Diam. Dia. of teeth Inches teeth Inches Length Factor* 1.46 44 4.411 64 6.416 1.46 26 2.607 38 3.810 1.47 30 3.008 44 4.411 1.47 38 3.810 56 5.614 1.50 24 2.406 36 3.609 1.50 32 3.208 48 4.812 1.50 48 4.812 72 7.218 1.54 26 2.607 40 4.010 1.55 22 2.206 34 3.409 1.56 36 3.609 56 5.614 1.56 72 7.218 112 11.229 1.57 28 2.807 44 4.411 1.58 24 2.406 38 3.810 1.60 30 3.008 48 4.812 1.60 40 4.010 64 6.416 1.61 56 5.614 90 9.023 1.64 22 2.206 36 3.609 1.64 44 4.411 72 7.218 1.65 34 3.409 56 5.614 1.67 24 2.406 40 4.010 1.67 48 4.812 80 8.020 1.68 38 3.810 64 6.416 1.69 26 2.607 44 4.411 1.71 28 2.807 48 4.812 1.73 22 2.206 38 3.810 1.75 32 3.208 56 5.614 1.75 64 6.416 112 11.229 1.78 36 3.609 64 6.416 1.80 40 4.010 72 7.218 1.80 80 8.020 144 14.437 1.82 22 2.206 40 4.010 1.82 44 4.411 80 8.020 1.83 24 2.406 44 4.411 1.85 26 2.607 48 4.812 1.87 30 3.008 56 5.614 1.88 48 4.812 90 9.023 1.88 34 3.409 64 6.416 1.90 38 3.810 72 7.218 Length Factor*

Engineering

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. * This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-43

ENGINEERING/TECHNICAL PAGES PT11- 4


DYNA-SYNC

SELECTION 8MM Pitch HT200 Belt Drive Selection Table

HT Synchrous Belts Sprockets Conveyor Components

Sprocket Combinations Driver Driven Speed Pitch Pitch Ratio No. of No. of Dia. Dia. teeth teeth Inches Inches Length Factor* 2.00 22 2.206 44 4.411 2.00 24 2.406 48 4.812 2.00 28 2.807 56 5.614 2.00 32 3.208 64 6.416 2.00 36 3.609 72 7.218 2.00 40 4.010 80 8.020 2.00 56 5.614 112 11.229 2.00 72 7.218 144 14.437 2.05 44 4.411 90 9.023 2.11 38 3.810 80 8.020 2.12 34 3.409 72 7.218 2.13 30 3.008 64 6.416 2.15 26 2.607 56 5.614 2.18 22 2.206 48 4.812 2.22 36 3.609 80 8.020 2.25 32 3.208 72 7.218 2.25 40 4.010 90 9.023 2.25 64 6.416 144 14.437 2.29 28 2.807 64 6.416 2.33 24 2.406 56 5.614 2.33 48 4.812 112 11.229 2.35 34 3.409 80 8.020 2.37 38 3.810 90 9.023 2.40 30 3.008 72 7.218 240 80 8.020 192 19.249 2.46 26 2.607 64 6.416 2.50 32 3.208 80 8.020 2.50 36 3.609 90 9.023 2.55 22 2.206 56 5.614 2.55 44 4.411 112 11.229 2.57 28 2.807 72 7.218 2.57 56 5.614 144 14.437 2.65 34 3.409 90 9.023 2.67 24 2.406 64 6.416 2.67 30 3.008 80 8.020 2.67 72 7.218 192 19.249 2.77 26 2.607 72 7.218 2.80 40 4.010 112 11.229 2.81 32 3.208 90 9.023 2.86 28 2.807 80 8.020 Length Factor*

Center Distance, Inches 5608M

6008M

6408M

7208M

8008M

8408M

8808M

9208M

9608M

1040- 1064- 1120- 1160- 12008M 8M 8M 8M 8M

0.80 5.72 5.22 ... ... ... ... ... ... ... ... ... ... ... 5.35 ... ... ... ... ... . . .. . . ... ... ... ... ... ... ... ... 4.56 ... ... ... ... ... ... ... ... ... ... ... 0.80

0.80 6.52 6.02 5.00 ... ... ... ... ... ... ... ... ... 5.13 6.16 ... ... ... ... ... 5.26 ... ... ... ... ... ... ... ... 5.40 ... ... ... ... ... ... ... ... ... ... ... 0.80

0.90 7.32 6.82 5.82 ... ... ... ... ... ... ... ... ... 5.95 6.97 ... ... ... ... ... 6.09 ... ... ... ... ... 5.16 ... ... 6.22 ... ... ... ... 5.29 ... ... ... ... ... ... 0.90

0.90 8.91 8.42 7.43 6.41 ... ... ... ... ... ... ... 6.55 7.57 8.56 ... ... ... ... 6.69 7.71 ... ... ... 5.75 ... 6.82 ... ... 7.85 ... 5.88 ... ... 6.96 ... ... 6.01 ... ... ... 0.90

0.90 10.50 10.01 9.03 8.03 7.01 ... ... ... ... ... 7.15 8.17 9.17 10.15 ... 7.28 ... ... 8.31 9.31 ... 6.35 ... 7.42 ... 8.45 6.48 ... 9.45 ... 7.55 ... ... 8.59 6.61 ... 7.68 ... ... 6.74 0.90

0.90 11.28 10.80 9.82 8.83 7.82 6.79 ... ... ... 6.92 7.96 8.97 9.96 10.95 7.05 8.10 ... ... 9.11 10.11 ... 7.19 ... 8.23 ... 9.25 7.32 ... 10.25 ... 8.37 ... ... 9.39 7.45 ... 8.50 ... ... 7.58 0.90

0.90 12.08 11.59 10.62 9.63 8.63 7.61 ... ... ... 7.75 8.77 9.77 10.76 11.74 7.88 8.91 ... ... 9.92 10.91 ... 8.01 6.74 9.05 ... 10.06 8.15 6.86 11.05 ... 9.19 ... 6.99 10.20 8.28 ... 9.32 ... 7.12 8.41 0.90

1.00 12.87 12.38 11.41 10.43 9.43 8.42 ... ... 7.19 8.56 9.57 10.57 11.56 12.53 8.70 9.71 7.45 ... 10.71 11.70 ... 8.83 7.58 9.85 ... 10.86 8.97 7.71 11.85 ... 9.99 ... 7.84 11.00 9.10 ... 10.13 ... 7.97 9.24 1.00

1.00 13.66 13.18 12.21 11.23 10.24 9.23 ... ... 8.01 9.37 10.38 11.37 12.35 13.32 9.51 10.52 8.28 ... 11.51 12.50 ... 9.65 8.41 10.66 ... 11.66 9.78 8.55 12.64 ... 10.80 ... 8.68 11.80 9.92 ... 10.94 ... 8.81 10.06 1.00

1.00 15.23 14.75 13.78 12.81 11.83 10.84 ... ... 9.64 10.98 11.97 12.96 13.93 14.90 11.12 12.12 9.92 ... 13.10 14.08 ... 11.26 10.05 12.26 ... 13.25 11.40 10.19 14.23 ... 12.40 ... 10.32 13.39 11.54 ... 12.54 ... 10.46 11.67 1.00

1.00 15.71 15.23 14.26 13.29 12.31 11.32 ... ... 10.13 11.46 12.45 13.44 14.41 15.38 11.60 12.60 10.41 ... 13.58 14.56 ... 11.74 10.54 12.74 ... 13.73 11.88 10.68 14.70 ... 12.88 ... 10.81 13.87 12.02 ... 13.02 8.16 10.95 12.16 1.00

1.00 16.81 16.33 15.37 14.40 13.42 12.43 ... ... 11.26 12.58 13.56 14.54 15.52 16.48 12.72 13.71 11.54 ... 14.69 15.66 8.86 12.86 11.67 13.85 ... 14.84 13.00 11.81 15.81 9.12 14.00 ... 11.95 14.98 13.14 ... 14.14 9.37 12.09 13.28 1.00

1.00 1.00 17.60 18.39 17.12 17.91 16.16 16.95 15.19 15.98 14.22 15.01 13.23 14.03 9.17 9.99 ... ... 12.06 12.86 13.38 14.17 14.36 15.15 15.34 16.13 16.31 17.10 17.27 18.06 13.52 14.32 14.51 15.30 12.34 13.14 ... ... 15.49 16.28 16.46 17.25 9.70 10.53 13.66 14.46 12.48 13.28 14.65 15.44 ... ... 15.63 16.42 13.81 14.60 12.62 13.43 16.61 17.39 9.96 10.79 14.80 15.59 ... ... 12.76 13.56 15.78 16.57 13.95 14.75 ... ... 14.94 15.73 10.22 11.06 12.90 13.70 14.09 14.89 1.00 1.00

Engineering

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. * This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-44

ENGINEERING/TECHNICAL PAGES PT11- 4


DYNA-SYNC

SELECTION 8MM Pitch HT200 Belt Drive Selection Table Center Distance, Inches

1.10 23.12 22.64 21.69 20.72 19.76 18.79 14.85 ... 17.64 18.94 19.91 20.87 21.84 22.80 19.08 20.06 17.93 11.24 21.02 21.99 15.41 19.23 18.08 20.20 ... 21.17 19.38 18.22 22.14 15.69 20.35 11.76 18.37 21.32 19.52 ... 20.50 15.97 18.51 19.67 1.10

1.10 24.54 24.07 23.11 22.15 21.18 20.22 16.29 12.22 19.07 20.36 21.33 22.30 23.26 24.22 20.51 21.48 19.37 12.75 22.45 23.41 16.86 20.66 19.51 21.63 ... 22.60 20.81 19.66 23.56 17.14 21.78 13.28 19.80 22.75 20.95 ... 21.93 17.42 19.95 21.10 1.10

1.10 25.96 25.48 24.53 23.57 22.60 21.64 17.73 13.69 20.50 21.79 22.75 23.72 24.68 25.63 21.94 22.90 20.79 14.23 23.87 24.83 18.30 22.08 20.94 23.05 ... 24.02 22.23 21.08 24.98 18.58 23.20 14.77 21.23 24.17 22.38 ... 23.35 18.86 21.38 22.53 1.10

1.10 26.27 25.80 24.84 23.88 22.92 21.96 18.05 14.02 20.82 22.10 23.07 24.03 24.99 25.95 22.25 23.22 21.11 14.56 24.18 25.14 18.62 22.40 21.26 23.37 ... 24.33 22.55 21.40 25.30 18.90 23.52 15.10 21.55 24.48 22.70 ... 23.67 19.19 21.69 22.84 1.10

1.10 29.43 28.95 28.00 27.04 26.08 25.12 21.23 17.26 23.98 25.27 26.23 27.19 28.15 29.10 25.42 26.38 24.28 17.81 27.34 28.30 21.81 25.56 24.43 26.53 ... 27.49 25.71 24.57 28.45 22.10 26.68 18.36 24.72 27.64 25.86 ... 26.83 22.38 24.87 26.01 1.10

1.20 30.22 29.74 28.79 27.83 26.87 25.91 22.03 18.07 24.78 26.06 27.02 27.98 28.94 29.89 26.21 27.17 25.07 18.62 28.13 29.09 22.61 26.36 25.22 27.32 ... 28.28 26.51 25.37 29.24 22.90 27.47 19.18 25.52 28.44 26.66 ... 27.62 23.18 25.66 26.80 1.20

1.20 34.16 33.68 32.73 31.77 30.81 29.85 25.99 22.07 28.73 30.00 30.97 31.92 32.88 33.83 30.16 31.12 29.03 22.64 32.08 33.03 26.58 30.31 29.17 31.27 17.04 32.23 30.46 29.32 33.18 26.87 31.42 23.20 29.47 32.38 30.61 17.56 31.57 27.16 29.62 30.76 1.20

1.20 38.09 37.62 36.66 35.71 34.75 33.80 29.94 26.05 32.67 33.95 34.91 35.86 36.82 37.77 34.10 35.06 32.97 26.62 36.02 36.97 30.54 34.25 33.12 35.21 21.16 36.17 34.40 33.27 37.12 30.83 35.36 27.20 33.42 36.32 34.55 21.70 35.51 31.13 33.57 34.70 1.20

1.20 42.03 41.56 40.61 39.65 38.70 37.74 33.90 30.02 36.62 37.90 38.85 39.81 40.76 41.71 38.05 39.00 36.92 30.60 39.96 40.91 34.50 38.20 37.07 39.16 25.21 40.11 38.35 37.23 41.07 34.79 39.31 31.18 37.38 40.27 38.50 25.77 39.46 35.09 37.53 38.65 1.20

1.20 45.97 45.50 44.54 43.59 42.64 41.68 37.85 33.98 40.56 41.84 42.79 43.75 44.70 45.65 41.99 42.94 40.87 34.57 43.90 44.85 38.45 42.14 41.02 43.10 29.24 44.05 42.29 41.17 45.01 38.75 43.25 35.15 41.32 44.21 42.44 29.80 43.40 39.04 41.47 42.60 1.20

1.20 49.91 49.44 48.49 47.53 46.58 45.63 41.80 37.94 44.51 45.78 46.73 47.69 48.64 49.59 45.93 46.89 44.81 38.53 47.84 48.79 42.40 46.09 44.97 47.04 33.24 48.00 46.24 45.12 48.95 42.70 47.19 39.12 45.27 48.15 46.39 33.81 47.35 43.00 45.42 46.54 1.20

1.20 54.79 54.32 53.37 52.42 51.46 50.51 46.69 42.84 49.40 50.67 51.62 52.57 53.52 54.47 50.82 51.77 49.70 43.44 52.73 53.68 47.29 50.97 49.85 51.93 38.18 52.88 51.12 50.01 53.83 47.59 52.08 44.03 50.16 53.03 51.28 38.76 52.23 47.90 50.31 51.43 1.20

1.20 59.36 58.88 57.93 56.98 56.03 55.08 51.26 47.42 53.96 55.23 56.19 57.14 58.09 59.04 55.39 56.34 54.27 48.02 57.29 58.24 51.87 55.54 54.42 56.49 42.79 57.45 55.69 54.58 58.40 52.17 56.65 48.62 54.73 57.60 55.85 43.37 56.80 52.47 54.88 56.00 1.20

1.20 65.66 65.18 64.24 63.29 62.34 61.38 57.57 53.74 60.27 61.54 62.49 63.44 64.39 65.34 61.69 62.64 60.58 54.34 63.60 64.55 58.18 61.85 60.73 62.80 49.14 63.75 62.00 60.88 64.70 58.48 62.95 54.94 61.04 63.90 62.15 49.73 63.11 58.79 61.19 62.31 1.20

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. * This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-45

ENGINEERING/TECHNICAL PAGES PT11- 4

1.20 81.41 80.94 79.99 79.04 78.09 77.14 73.33 69.51 76.03 77.30 78.25 79.20 80.14 81.09 77.45 78.40 76.34 70.12 79.35 80.30 73.95 77.60 76.49 78.56 64.97 79.51 77.76 76.65 80.46 74.25 78.71 70.73 76.80 79.66 77.91 65.56 78.86 74.56 76.95 78.07 1.20

Sprockets

1.10 19.97 19.49 18.53 17.56 16.59 15.62 11.63 ... 14.46 15.76 16.74 17.71 18.68 19.64 15.91 16.89 14.75 ... 17.86 18.83 12.17 16.05 14.89 17.03 ... 18.01 16.20 15.03 18.98 12.44 17.18 ... 15.17 18.16 16.34 ... 17.32 12.71 15.31 16.49 1.10

Conveyor Components

1.00 18.87 18.39 17.42 16.46 15.49 14.51 10.49 ... 13.34 14.65 15.63 16.61 17.57 18.54 14.80 15.78 13.63 ... 16.75 17.72 11.03 14.94 13.77 15.92 ... 16.90 15.08 13.91 17.87 11.29 16.07 ... 14.05 17.05 15.23 ... 16.21 11.56 14.19 15.37 1.00

HT Synchrous Belts

1224- 1280- 1440- 1512- 1584- 1600- 1760- 1800- 2000- 2200- 2400- 2600- 2800- 3048- 3280- 3600- 44008M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M

Engineering

Sprocket Combinations Driver Driven Speed Ratio No. Pitch No. Pitch of Diam. Dia. of teeth Inches teeth Inches Length Factor* 2.00 22 2.206 44 4.411 2.00 24 2.406 48 4.812 2.00 28 2.807 56 5.614 2.00 32 3.208 64 6.416 2.00 36 3.609 72 7.218 2.00 40 4.010 80 8.020 2.00 56 5.614 112 11.229 2.00 72 7.218 144 14.437 2.05 44 4.411 90 9.023 2.11 38 3.810 80 8.020 2.12 34 3.409 72 7.218 2.13 30 3.008 64 6.416 2.15 26 2.607 56 5.614 2.18 22 2.206 48 4.812 2.22 36 3.609 80 8.020 2.25 32 3.208 72 7.218 2.25 40 4.010 90 9.023 2.25 64 6.416 144 14.437 2.29 28 2.807 64 6.416 2.33 24 2.406 56 5.614 2.33 48 4.812 112 11.229 2.35 34 3.409 80 8.020 2.37 38 3.810 90 9.023 2.40 30 3.008 72 7.218 240 80 8.020 192 19.249 2.46 26 2.607 64 6.416 2.50 32 3.208 80 8.020 2.50 36 3.609 90 9.023 2.55 22 2.206 56 5.614 2.55 44 4.411 112 11.229 2.57 28 2.807 72 7.218 2.57 56 5.614 144 14.437 2.65 34 3.409 90 9.023 2.67 24 2.406 64 6.416 2.67 30 3.008 80 8.020 2.67 72 7.218 192 19.249 2.77 26 2.607 72 7.218 2.80 40 4.010 112 11.229 2.81 32 3.208 90 9.023 2.86 28 2.807 80 8.020 Length Factor*


DYNA-SYNC

SELECTION 8MM Pitch HT200 Belt Drive Selection Table Speed Ratio

HT Synchrous Belts Sprockets Conveyor Components

2.91 2.95 3.00 3.00 3.00 3.00 3.08 3.11 3.21 3.27 3.27 3.29 3.33 3.43 3.46 3.50 3.60 3.64 3.73 3.75 3.79 4.00 4.00 4.00 4.09 4.24 4.31 4.36 4.50 4.67 4.80 4.80 5.05 5.09 5.14 5.33 5.54 5.65 6.00 6.00 6.40 6.55 6.86

Sprocket Combinations Driver Driven Pitch Pitch No. of No. of Dia. Dia. teeth teeth Inches Inches Length Factor* 22 2.206 64 6.416 38 3.810 112 11.229 24 2.406 72 7.218 30 3.008 90 9.023 48 4.812 144 14.437 64 6.416 192 19.249 26 2.607 80 8.020 36 3.609 112 11.229 28 2.807 90 9.023 22 2.206 72 7.218 44 4.411 144 14.437 34 3.409 112 11.229 24 2.406 80 8.020 56 5.614 192 19.249 26 2.607 90 9.023 32 3.208 112 11.229 40 4.010 144 14.437 22 2.206 80 8.020 30 3.008 112 11.229 24 2.406 90 9.023 38 3.810 144 14.437 28 2.807 112 11.229 36 3.609 144 14.437 48 4.812 192 19.249 22 2.206 90 9.023 34 3.409 144 14.437 26 2.607 112 11.229 44 4.411 192 19.249 32 3.208 144 14.437 24 2.406 112 11.229 30 3.008 144 14.437 40 4.010 192 19.249 38 3.810 192 19.249 22 2.206 112 11.229 28 2.807 144 14.437 36 3.609 192 19.249 26 2.607 144 14.437 34 3.409 192 19.249 24 2.406 144 14.437 32 3.208 192 19.249 30 3.008 192 19.249 22 2.206 144 14.437 28 2.807 192 19.249 Length Factor*

Center Distance, Inches 7208M

8008M

8408M

8808M

9208M

9608M

10408M

10648M

11208M

11608M

12008M

0.90 7.09 ... 6.14 ... ... ... ... ... ... 6.27 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0.90

0.90 8.72 ... 7.82 ... ... ... 6.86 . . .. ... 7.95 ... ... 6.99 ... ... ... ... 7.12 ... ... ... ... ... ... 5.92 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0.90

0.90 9.53 ... 8.64 6.36 ... ... 7.71 ... 6.48 8.77 ... ... 7.84 ... 6.61 ... ... 7.97 ... 6.73 ... ... ... ... 6.85 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0.90

0.90 10.34 ... 9.46 7.24 ... ... 8.55 ... 7.37 9.59 ... ... 8.68 ... 7.49 ... ... 8.81 ... 7.62 ... ... ... ... 7.74 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0.90

1.00 11.14 ... 10.27 8.10 ... ... 9.37 ... 8.22 10.41 ... ... 9.50 ... 8.35 ... ... 9.64 ... 8.48 ... ... ... ... 8.61 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 1.00

1.00 11.94 ... 11.08 8.94 ... ... 10.19 ... 9.07 11.22 ... ... 10.33 ... 9.20 ... ... 10.46 ... 9.33 ... ... ... ... 9.46 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 1.00

1.00 13.53 ... 12.68 10.59 ... ... 11.81 7.88 10.73 12.82 ... 8.00 11.95 ... 10.86 8.12 ... 12.09 8.24 10.99 ... 8.36 ... ... 11.12 ... 8.48 ... ... 8.60 ... ... ... 8.72 ... ... ... ... ... ... ... ... ... 1.00

1.00 14.01 8.29 13.17 11.09 ... ... 12.30 8.41 11.22 13.31

1.00 15.13 9.50 14.28 12.22 ... ... 13.42 9.63 12.36 14.43 ... 9.75 13.56 ... 12.50 9.88 ... 13.70 10.01 12.63 ... 10.13 ... ... 12.77 ... 10.26 ... ... 10.38 ... ... ... 10.51 ... ... ... ... ... ... ... ... ... 1.00

1.00 15.92 10.35 15.08 13.04 ... ... 14.23 10.48 13.18 15.23 ... 10.61 14.37 ... 13.31 10.74 ... 14.51 10.87 13.45 ... 10.99 ... ... 13.59 ... 11.12 ... ... 11.25 ... ... ... 11.38 ... ... ... ... ... ... ... ... ... 1.00

1.00 16.72 11.19 15.88 13.84 ... ... 15.03 11.32 13.98 16.02 ... 11.45 15.17 ... 14.12 11.58 ... 15.31 11.71 14.26 ... 11.84 ... ... 14.40 ... 11.97 ... ... 12.10 ... ... ... 12.23 ... ... ... ... ... ... ... ... ... 1.00

8.54 12.44 ... 11.35 8.66 ... 12.58 8.78 11.49 ... 8.91 ... ... 11.62 ... 9.03 ... ... 9.15 ... ... ... 9.27 ... ... ... ... ... ... ... ... ... 1.00

Engineering

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. * This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-46

ENGINEERING/TECHNICAL PAGES PT11- 4


1224 -8M

1280 1440 1512- 1584- 1600- 1760- 1800- 2000- 2200- 2400- 2600- 2800- 3048- 3280- 3600- 44008M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M 8M

1.00 17.19 11.69 16.36 14.33 ... ... 15.51 11.82 14.47 16.50 ... 11.95 15.65 ... 14.61 12.08 ... 15.80 12.21 14.75 ... 12.35 ... ... 14.88 ... 12.48 ... ... 12.61 ... ... ... 12.74 ... ... ... ... ... ... ... 8.80 ... 1.00

1.10 18.30 12.84 17.47 15.45 ... ... 16.63 12.98 15.59 17.61 ... 13.11 16.77 ... 15.73 13.24 ... 16.91 13.38 15.87 ... 13.51 9.42 ... 16.01 9.53 13.64 ... 9.65 13.77 9.77 ... ... 13.90 9.89 ... 10.00 ... 10.12 ... ... 10.24 ... 1.10

1.10 21.47 16.10 20.65 18.65 12.27 ... 19.81 16.24 18.80 20.79 12.52 16.38 19.96 ... 18.94 16.52 12.78 20.10 16.65 19.08 12.90 16.79 13.03 ... 19.22 13.16 16.93 ... 13.28 17.06 13.41 ... ... 17.20 13.53 ... 13.66 ... 13.78 ... ... 13.91 ... 1.10

1.10 22.90 17.56 22.08 20.09 13.80 ... 21.25 17.70 20.23 22.22 14.06 17.84 21.39 ... 20.38 17.98 14.32 21.54 18.11 20.52 14.45 18.25 14.57 ... 20.66 14.70 18.39 ... 14.83 18.53 14.96 ... ... 18.67 15.09 ... 15.21 ... 15.34 ... ... 15.47 ... 1.10

1.10 24.32 19.01 23.50 21.52 15.30 ... 22.67 19.15 21.67 23.65 15.56 19.29 22.82 ... 21.81 19.43 15.82 22.96 19.56 21.95 15.96 19.70 16.09 ... 22.10 16.22 19.84 ... 16.35 19.98 16.48 ... ... 20.12 16.61 ... 16.74 ... 16.87 ... ... 17.00 ... 1.10

1.10 24.63 19.33 23.81 21.84 15.63 ... 22.99 19.47 21.98 23.96 15.89 19.61 23.14 ... 22.13 19.75 16.16 23.28 19.89 22.27 16.29 20.03 16.42 ... 22.42 16.55 20.17 ... 16.68 20.30 16.81 ... ... 20.44 16.94 ... 17.07 ... 17.20 ... ... 17.33 ... 1.10

1.10 27.79 22.53 26.98 25.01 18.91 ... 26.16 22.67 25.16 27.13 19.18 22.81 26.31 13.39 25.31 22.95 19.45 26.45 23.10 25.45 19.59 23.24 19.72 13.88 25.60 19.86 23.38 4.12 19.99 23.52 20.13 14.37 14.49 23.66 20.26 14.61 20.39 14.73 20.53 14.85 14.97 20.66 15.09 1.10

1.20 28.59 23.33 27.77 25.81 19.73 ... 26.95 23.47 25.96 27.92 20.00 23.61 27.10 14.29 26.10 23.76 20.27 27.25 23.90 26.25 20.41 24.04 20.54 14.78 26.40 20.68 24.18 15.03 20.81 24.32 20.95 15.27 15.40 24.47 21.08 15.52 21.22 15.64 21.35 15.76 15.89 21.49 16.01 1.20

1.20 32.53 27.31 31.72 29.77 23.76 18.08 30.90 27.45 29.92 31.87 24.04 27.60 31.05 18.60 30.06 27.74 24.32 31.20 27.88 30.21 24.46 28.03 24.60 19.12 30.36 24.74 28.17 19.38 24.88 28.32 25.01 19.63 19.76 28.46 25.15 19.89 25.29 20.02 25.43 20.14 20.27 25.56 20.40 1.20

1.20 36.47 31.27 35.67 33.72 27.77 22.23 34.85 31.42 33.87 35.82 28.05 31.57 35.00 22.77 34.02 31.71 28.34 35.15 31.86 34.17 28.48 32.00 28.62 23.30 34.32 28.76 32.15 25.57 28.90 32.29 29.04 23.83 23.96 32.44 29.18 24.09 29.32 24.23 29.46 24.36 24.49 29.60 24.62 1.20

1.20 40.42 35.24 39.61 37.68 31.76 26.31 38.80 35.39 37.83 39.76 32.05 35.53 38.96 26.86 37.98 35.68 32.34 39.11 35.83 38.13 32.48 35.97 32.62 27.41 38.27 32.76 36.12 27.68 32.91 36.27 33.05 27.95 28.08 36.41 33.19 28.22 33.33 28.35 33.47 28.49 28.62 33.62 28.75 1.20

1.20 44.36 39.19 43.55 41.62 35.74 30.36 42.75 39.34 41.77 43.71 36.03 39.49 42.90 30.91 41.92 39.64 36.32 43.05 39.79 42.07 36.46 39.93 36.61 31.47 42.22 36.75 40.08 31.74 36.89 40.23 37.04 32.02 32.15 40.38 37.18 32.29 37.32 32.43 37.47 32.56 32.70 37.61 32.84 1.20

1.20 48.30 43.15 47.50 45.57 39.71 34.37 46.70 43.30 45.72 47.65 40.00 43.45 46.85 34.94 45.87 43.60 40.29 47.00 43.75 46.02 40.44 43.89 40.59 35.50 46.17 40.73 44.04 35.78 40.88 44.19 41.02 36.05 36.19 44.34 41.17 36.33 41.31 36.47 41.45 36.61 36.75 41.60 36.89 1.20

1.20 53.19 48.05 52.39 50.46 44.62 39.33 51.58 48.20 50.61 52.54 44.92 48.35 51.74 39.90 50.76 48.50 45.21 51.89 48.64 50.92 45.36 48.79 45.50 40.47 51.07 45.65 48.94 40.75 45.80 49.09 45.94 41.03 41.18 49.24 46.09 41.32 46.23 41.46 46.38 41.60 41.74 46.53 41.88 1.20

1.20 57.75 52.62 56.96 55.03 49.21 43.95 56.15 52.77 55.19 57.11 49.51 52.92 56.31 44.53 55.34 53.07 49.80 56.46 53.22 55.49 49.95 53.37 50.10 45.10 55.64 50.25 53.52 45.39 50.39 53.67 50.54 45.67 45.82 53.82 50.69 45.96 50.83 46.10 50.98 46.24 46.38 51.13 46.53 1.20

1.20 64.06 58.94 63.26 61.34 55.54 50.31 62.46 59.09 61.50 63.41 55.84 59.24 62.61 50.89 61.65 59.39 56.13 62.77 59.54 61.80 56.28 59.69 56.43 51.47 61.95 56.58 59.84 51.76 56.73 59.99 56.88 52.05 52.19 60.14 57.02 52.34 57.17 52.48 57.32 52.63 52.77 57.47 52.91 1.20

1.20 79.82 74.71 79.02 77.11 71.33 66.16 78.22 74.86 77.26 79.17 71.64 75.02 78.38 66.75 77.41 75.17 71.94 78.53 75.32 77.57 72.09 75.47 72.24 67.34 77.72 72.39 75.63 67.63 72.54 75.78 72.69 67.93 68.08 75.93 72.84 68.22 72.99 68.37 73.14 68.52 68.66 73.29 68.81 1.20

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. * This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-47

ENGINEERING/TECHNICAL PAGES PT11- 4

Sprockets

2.91 2.95 3.00 3.00 3.00 3.00 3.08 3.11 3.21 3.27 3.27 3.29 3.33 3.43 3.46 3.50 3.60 3.64 3.73 3.75 3.79 4.00 4.00 4.00 4.09 4.24 4.31 4.36 4.50 4.67 4.80 4.80 5.05 5.09 5.14 5.33 5.54 5.65 6.00 6.00 6.40 6.55 6.86

Center Distance, Inches

Conveyor Components

Speed Ratio

Sprocket Combinations Driver Driven No. Pitch No. Pitch of Diam. Dia. of teeth Inches teeth Inches Length Factor* 22 2.206 64 6.416 38 3.810 112 11.229 24 2.406 72 7.218 30 3.008 90 9.023 48 4.812 144 14.437 64 6.416 192 19.249 26 2.607 80 8.020 36 3.609 112 11.229 28 2.807 90 9.023 22 2.206 72 7.218 44 4.411 144 14.437 34 3.409 112 11.229 24 2.406 80 8.020 56 5.614 192 19.249 26 2.607 90 9.023 32 3.208 112 11.229 40 4.010 144 14.437 22 2.206 80 8.020 30 3.008 112 11.229 24 2.406 90 9.023 38 3.810 144 14.437 28 2.807 112 11.229 36 3.609 144 14.437 48 4.812 192 19.249 22 2.206 90 9.023 34 3.409 144 14.437 26 2.607 112 11.229 44 4.411 192 19.249 32 3.208 144 14.437 24 2.406 112 11.229 30 3.008 144 14.437 40 4.010 192 19.249 38 3.810 192 19.249 22 2.206 112 11.229 28 2.807 144 14.437 36 3.609 192 19.249 26 2.607 144 14.437 34 3.409 192 19.249 24 2.406 144 14.437 32 3.208 192 19.249 30 3.008 192 19.249 22 2.206 144 14.437 28 2.807 192 19.249 Length Factor*

Engineering

8MM Pitch HT200 Belt Drive Selection Table

HT Synchrous Belts

DYNA-SYNC

SELECTION


DYNA-SYNC

SELECTION 14MM Pitch HT200 Belt Drive Selection Table Speed Ratio

HT Synchrous Belts Sprockets Conveyor Components

1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.03 1.04 1.05 1.06 1.06 1.06 1.06 1.06 1.07 1.07 1.07 1.07 1.08 1.08 1.09 1.10 1.10 1.11 1.11 1.12 1.13 1.13 1.13

Sprocket Combinations Driver Driven Pitch Pitch No. of No. of Dia. Dia. Teeth Teeth Inches Inches Length Factor* 28 4.912 28 4.912 29 5.088 29 5.088 30 5.263 30 5.263 32 5.614 32 5.614 34 5.965 34 5.965 36 6.316 36 6.316 38 6.667 38 6.667 40 7.018 40 7.018 44 7.720 44 7.720 48 8.421 48 8.421 52 9.123 52 9.123 56 9.825 56 9.825 60 10.527 60 10.527 64 11.229 64 11.229 68 11.930 68 11.930 72 12.632 72 12.632 80 14.036 80 14.036 29 5.088 30 5.263 28 4.912 29 5.088 38 6.667 40 7.018 36 6.316 38 6.667 34 5.965 36 6.316 68 11.930 72 12.632 32 5.614 34 5.965 64 11.229 68 11.930 30 5.263 32 5.614 60 10.527 64 11.229 28 4.912 30 5.263 56 9.825 60 10.527 52 9.123 56 9.825 48 8.421 52 9.123 44 7.720 48 8.421 40 7.018 44 7.720 29 5.088 32 5.614 36 6.316 40 7.018 72 12.632 80 14.036 34 5.965 38 6.667 32 5.614 36 6.316 64 11.229 72 12.632 80 14.036 90 15.790 Length Factor*

Center Distance, Inches 96614M

119014M

140014M

161014M

177814M

189014M

210014M

231014M

245014M

259014M

280014M

0.80 11.30 11.02 10.75 10.20 9.65 9.09 8.54 7.99 ... ... ... ... ... ... ... ... ... 10.88 11.16 8.26 8.82 9.37 ... 9.92 ... 10.47 ... 11.02 ... ... ... ... ... 10.61 8.54 ... 9.09 9.64 ... ... 0.80

0.80 15.71 15.43 15.16 14.61 14.06 13.50 12.95 12.40 11.30 10.20 ... ... ... ... ... ... ... 15.30 15.57 12.68 13.23 13.78 ... 14.33 ... 14.88 ... 15.43 ... ... 9.64 10.74 11.84 15.02 12.95 ... 13.5.0 14.05 ... ... 0.80

0.90 19.84 19.57 19.29 18.74 18.19 17.64 17.09 16.54 15.43 14.33 13.23 12.13 ... ... ... ... ... 19.43 19.71 16.81 17.36 17.91 ... 18.47 ... 19.02 ... 19.57 11.57 12.67 13.78 14.88 15.98 19.15 17.08 ... 17.64 18.19 ... ... 0.90

0.90 23.98 23.70 23.43 22.88 22.33 21.77 21.22 20.67 19.57 18.47 17.36 16.26 15.16 14.06 12.96 ... ... 23.57 23.84 20.95 21.50 22.05 ... 22.60 13.50 23.15 14.60 23.70 15.71 16.81 17.91 19.01 20.12 23.29 21.22 ... 21.77 22.32 12.94 ... 0.90

0.95 27.28 27.01 26.73 26.18 25.63 25.08 24.53 23.98 22.87 21.77 20.67 19.57 18.46 17.36 16.26 15.16 ... 26.87 27.15 24.25 24.80 25.35 15.71 25.91 16.81 26.46 17.91 27.01 19.01 20.12 21.22 22.32 23.42 26.59 24.52 14.04 25.08 25.63 16.24 ... 0.95

0.95 29.49 29.21 28.94 28.39 27.84 27.28 26.73 26.18 25.08 23.98 22.87 21.77 20.67 19.57 18.47 17.36 15.16 29.08 29.35 26.46 27.01 27.56 17.91 28.11 19.01 28.66 20.11 29.21 21.22 22.32 23.42 24.53 25.63 28.80 26.73 16.24 27.28 27.83 18.45 ... 0.95

1.00 33.62 33.35 33.07 32.52 31.97 31.42 30.87 30.32 29.21 28.11 27.01 25.91 24.80 23.70 22.60 21.50 19.29 33.21 33.49 30.59 31.14 31.69 22.05 32.25 23.15 32.80 24.25 33.35 25.35 26.46 27.56 28.66 29.76 32.93 30.87 20.38 31.42 31.97 22.59 17.89 1.00

1.00 37.75 37.48 37.20 36.65 36.10 35.55 35.00 34.45 33.34 32.24 31.14 30.04 28.93 27.83 26.73 25.63 23.42 37.34 37.62 34.72 35.27 35.82 26.18 36.38 27.28 36.93 28.38 37.48 29.48 30.59 31.69 32.79 33.89 37.06 35.00 24.51 35.55 36.10 26.72 22.03 1.00

1.00 40.51 40.24 39.96 39.41 38.86 38.31 37.76 37.21 36.10 35.00 33.90 32.80 31.69 30.59 29.49 28.39 26.18 40.10 40.38 37.48 38.03 38.58 28.94 39.14 30.04 39.69 31.14 40.24 32.24 33.35 34.45 35.55 36.65 39.82 37.76 27.28 38.31 38.86 29.48 24.79 1.00

1.05 43.27 42.99 42.72 42.17 41.62 41.06 40.51 39.96 38.86 37.76 36.65 35.55 34.45 33.35 32.25 31.14 28.94 42.86 43.13 40.24 40.79 41.34 31.69 41.89 32.79 42.44 33.90 42.99 35.00 36.10 37.20 38.31 39.41 42.58 40.51 30.03 41.06 41.61 32.24 27.55 1.05

1.05 47.40 47.13 46.85 46.30 45.75 45.20 44.65 44.10 42.99 41.89 40.79 39.69 38.58 37.48 36.38 35.28 33.07 46.99 47.27 44.37 44.92 45.47 35.83 46.03 36.93 46.58 38.03 47.13 39.13 40.24 41.34 42.44 43.54 46.71 44.65 34.17 45.20 45.75 36.37 31.68 1.05

Engineering

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. * This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-48

ENGINEERING/TECHNICAL PAGES PT11- 4


315014M

336014M

350014M

385014M

432614M

457814M

495614M

532014M

574014M

616014M

686014M

1.05 54.29 54.02 53.74 53.19 52.64 52.09 51.54 50.99 49.88 48.78 47.68 46.58 45.47 44.37 43.27 42.17 39.96 53.88 54.16 51.26 51.81 52.36 42.72 52.92 43.82 53.47 44.92 54.02 46.02 47.13 48.23 49.33 50.43 53.60 51.54 41.06 52.09 52.64 43.26 38.57 1.05

1.10 58.42 58.15 57.87 57.32 56.77 56.22 55.67 55.12 54.01 52.91 51.81 50.71 49.60 48.50 47.40 46.30 44.09 58.01 58.29 55.39 55.94 56.49 46.85 57.05 47.95 57.60 49.05 58.15 50.15 51.26 52.36 53.46 54.56 57.73 55.67 45.19 56.22 56.77 47.39 42.71 1.10

1.10 61.18 60.91 60.63 60.08 59.53 58.98 58.43 57.88 56.77 55.67 54.57 53.47 52.36 51.26 50.16 49.06 46.85 60.77 61.05 58.15 58.70 59.25 49.61 59.81 50.71 60.36 51.81 60.91 52.91 54.02 55.12 56.22 57.32 60.49 58.43 47.95 58.98 59.53 50.15 45.47 1.10

1.10 68.07 67.79 67.52 66.97 66.42 65.86 65.31 64.76 63.66 62.56 61.45 60.35 59.25 58.15 57.05 55.94 53.74 67.66 67.93 65.04 65.59 66.14 56.49 66.69 57.59 67.24 58.70 67.79 59.80 60.90 62.00 63.11 64.21 67.38 65.31 54.84 65.86 66.41 57.04 52.35 1.10

1.10 77.44 77.16 76.89 76.34 75.79 75.23 74.68 74.13 73.03 71.93 70.82 69.72 68.62 67.52 66.42 65.31 63.11 77.03 77.30 74.41 74.96 75.51 65.86 76.06 66.97 76.61 68.07 77.16 69.17 70.27 71.38 72.48 73.58 76.75 74.68 64.21 75.23 75.78 66.41 61.72 1.10

1.10 82.40 82.13 81.85 81.30 80.75 80.20 79.65 79.10 77.99 76.89 75.79 74.69 73.58 72.48 71.38 70.28 68.07 81.99 82.27 79.37 79.92 80.47 70.83 81.03 71.93 81.58 73.03 82.13 74.13 75.24 76.34 77.44 78.54 81.71 79.65 69.17 80.20 80.75 71.38 66.69 1.10

1.10 89.84 89.57 89.29 88.74 88.19 87.64 87.09 86.54 85.43 84.33 83.23 82.13 81.02 79.92 78.82 77.72 75.51 89.43 89.71 86.81 87.36 87.91 78.27 88.47 79.37 89.02 80.47 89.57 81.57 82.68 83.78 84.88 85.98 89.15 87.09 76.61 87.64 88.19 78.82 74.13 1.10

1.10 97.01 96.73 96.46 95.91 95.36 94.80 94.25 93.70 92.60 91.50 90.39 89.29 88.19 87.09 85.99 84.88 82.68 96.60 96.87 93.98 94.53 95.08 85.43 95.63 86.54 96.18 87.64 96.73 88.74 89.84 90.95 92.05 93.15 96.32 94.25 83.78 94.80 95.35 85.98 81.29 1.10

1.10 105.27 105.00 104.72 104.17 103.62 103.07 102.52 101.97 100.86 99.76 98.66 97.56 96.45 95.35 94.25 93.15 90.94 104.86 105.14 102.24 102.79 103.34 93.70 103.90 94.80 104.45 95.90 105.00 97.00 98.11 99.21 100.31 101.41 104.58 102.52 92.04 103.07 103.62 94.25 89.56 1.10

1.10 113.54 113.27 112.99 112.44 111.89 111.34 110.79 110.24 109.13 108.03 106.93 105.83 104.72 103.62 102.52 101.42 99.21 113.13 113.41 110.51 111.06 111.61 101.97 112.17 103.07 112.72 104.17 113.27 105.27 106.38 107.48 108.58 109.68 112.85 110.79 100.31 111.34 111.89 102.52 97.83 1.10

1.10 127.32 127.05 126.77 126.22 125.67 125.12 124.57 124.02 122.91 121.81 120.71 119.61 118.50 117.40 116.30 115.20 112.99 126.91 127.19 124.29 124.84 125.39 115.75 125.95 116.85 126.50 117.95 127.05 119.06 120.16 121.26 122.36 123.46 126.63 124.57 114.09 125.12 125.67 116.30 111.61 1.10

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. * This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-49

ENGINEERING/TECHNICAL PAGES PT11- 4

Sprockets

1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.03 1.04 1.05 1.06 1.06 1.06 1.06 1.06 1.07 1.07 1.07 1.07 1.08 1.08 1.09 1.10 1.10 1.11 1.11 1.12 1.13 1.13 1.13

Center Distance, Inches

Conveyor Components

Speed Ratio

Sprocket Combinations Driver Driven Pitch Pitch No. of No. of Dia. Dia. teeth teeth Inches Inches Length Factor* 28 4.912 28 4.912 29 5.088 29 5.088 30 5.263 30 5.263 32 5.614 32 5.614 34 5.965 34 5.965 36 6.316 36 6.316 38 6.667 38 6.667 40 7.018 40 7.018 44 7.720 44 7.720 48 8.421 48 8.421 52 9.123 52 9.123 56 9.825 56 9.825 60 10.527 60 10.527 64 11.229 64 11.229 68 11.930 68 11.930 72 12.632 72 12.632 80 14.036 80 14.036 29 5.088 30 5.263 28 4.912 29 5.088 38 6.667 40 7.018 36 6.316 38 6.667 34 5.965 36 6.316 68 11.930 72 12.632 32 5.614 34 5.965 64 11.229 68 11.930 30 5.263 32 5.614 60 10.527 64 11.229 28 4.912 30 5.263 56 9.825 60 10.527 52 9.123 56 9.825 48 8.421 52 9.123 44 7.720 48 8.421 40 7.018 44 7.720 29 5.088 32 5.614 36 6.316 40 7.018 72 12.632 80 14.036 34 5.965 38 6.667 32 5.614 36 6.316 64 11.229 72 12.632 80 14.036 90 15.790 Length Factor*

Engineering

14MM Pitch HT200 Belt Drive Selection Table

HT Synchrous Belts

DYNA-SYNC

SELECTION


DYNA-SYNC

SELECTION 14MM Pitch HT200 Belt Drive Selection Table Speed Ratio

HT Synchrous Belts Sprockets Conveyor Components

1.13 1.13 1.14 1.14 1.15 1.16 1.17 1.17 1.18 1.18 1.18 1.19 1.20 1.20 1.20 1.21 1.21 1.22 1.23 1.24 1.25 1.25 1.25 1.25 1.26 1.27 1.27 1.29 1.29 1.29 1.30 1.31 1.31 1.32 1.33 1.33 1.33 1.33 1.36 1.36

Sprocket Combinations Driver Driven Pitch Pitch No. of No. of Dia. Dia. Teeth Teeth Inches Inches Length Factor* 30 5.263 34 5.965 60 10.527 68 11.930 28 4.912 32 5.614 56 9.825 64 11.229 52 9.123 60 10.527 38 6.667 44 7.720 48 8.421 56 9.825 29 5.088 34 5.965 34 5.965 40 7.018 68 11.930 80 14.036 44 7.720 52 9.123 32 5.614 38 6.667 30 5.263 36 6.316 40 7.018 48 8.421 60 10.527 72 12.632 28 4.912 34 5.965 56 9.825 68 11.930 36 6.316 44 7.720 52 9.123 64 11.229 29 5.088 36 6.316 32 5.614 40 7.018 48 8.421 60 10.527 64 11.229 80 14.036 72 12.632 90 15.790 38 6.667 48 8.421 30 5.263 38 6.667 44 7.720 56 9.825 28 4.912 36 6.316 56 9.825 72 12.632 34 5.965 44 7.720 40 7.018 52 9.123 52 9.123 68 11.930 29 5.088 38 6.667 68 11.930 90 15.790 30 5.263 40 7.018 36 6.316 48 8.421 48 8.421 64 11.229 60 10.527 80 14.036 28 4.912 38 6.667 44 7.720 60 10.527 Length Factor*

Center Distance, Inches 96614M

119014M

140014M

161014M

177814M

189014M

210014M

231014M

245014M

259014M

280014M

0.80 10.19 ... 10.74 ... ... ... ... 10.32 8.80 ... ... 9.35 9.91 ... ... 10.46 ... 7.96 ... 10.04 9.07 ... ... ... ... 9.62 ... 10.17 ... 8.22 ... ... 9.75 ... 9.33 ... ... ... 9.88 ... 0.80

0.80 14.60 ... 15.15 ... ... 12.11 ... 14.74 13.22 ... 10.17 13.77 14.32 11.28 ... 14.87 ... 12.38 ... 14.46 13.49 ... ... ... 11.54 14.04 9.59 14.59 ... 12.65 10.70 ... 14.17 ... 13.75 11.80 ... ... 14.30 ... 0.80

0.90 18.74 ... 19.29 ... 12.11 16.25 13.21 18.87 17.36 ... 14.31 17.91 18.46 15.42 ... 19.01 ... 16.52 11.53 18.59 17.62 12.63 ... ... 15.69 18.18 13.74 18.73 ... 16.79 14.85 ... 18.31 ... 17.89 15.95 12.05 ... 18.45 13.15 0.90

0.90 22.87 14.04 23.43 15.14 16.25 20.39 17.35 23.01 21.49 ... 18.45 22.04 22.59 19.56 13.46 23.15 14.57 20.66 15.68 22.73 21.76 16.78 ... ... 19.83 22.31 17.88 22.87 13.99 20.93 18.99 15.09 22.45 ... 22.03 20.09 16.20 ... 22.58 17.31 0.90

0.95 26.18 17.35 26.73 18.45 19.55 23.69 20.66 26.32 24.80 14.57 21.76 25.35 25.90 22.86 16.78 26.45 17.88 23.97 18.99 26.04 25.07 20.09 15.09 ... 23.13 25.62 21.19 26.17 17.31 24.24 22.30 18.41 25.76 ... 25.34 23.40 19.52 15.61 25.89 20.62 0.95

0.95 28.38 19.55 28.94 20.66 21.76 25.90 22.86 28.52 27.00 16.78 23.97 27.55 28.11 25.07 18.99 28.66 20.09 26.17 21.19 28.24 27.27 22.30 17.30 14.80 25.34 27.83 23.40 28.38 19.52 26.44 24.51 20.62 27.96 15.31 27.55 25.61 21.73 17.83 28.10 22.83 0.95

1.00 32.52 23.69 33.07 24.79 25.90 30.04 27.00 32.66 31.14 20.92 28.10 31.69 32.24 29.21 23.13 32.79 24.23 30.31 25.33 32.38 31.41 26.44 21.45 18.95 29.48 31.96 27.54 32.51 23.66 30.58 28.64 24.77 32.10 19.47 31.68 29.75 25.87 21.98 32.23 26.97 1.00

1.00 36.65 27.82 37.20 28.93 30.03 34.17 31.13 36.79 35.27 25.05 32.23 35.82 36.37 33.34 27.26 36.92 28.36 34.44 29.47 36.51 35.54 30.57 25.59 23.09 33.61 36.09 31.67 36.64 27.80 34.71 32.78 28.90 36.23 23.62 35.81 33.88 30.00 26.12 36.37 31.11 1.00

1.00 39.41 30.58 39.96 31.69 32.79 36.93 33.89 39.55 38.03 27.82 34.99 38.58 39.13 36.10 30.02 39.68 31.13 37.20 32.23 39.27 38.30 33.33 28.35 25.86 36.37 38.85 34.43 39.41 30.56 37.47 35.54 31.66 38.99 26.39 38.57 36.64 32.77 28.88 39.13 33.87 1.00

1.05 42.17 33.34 42.72 34.44 35.54 39.68 36.65 42.30 40.78 30.57 37.75 41.34 41.89 38.85 32.78 42.44 33.88 39.95 34.98 42.02 41.06 36.09 31.11 28.62 39.13 41.61 37.19 42.16 33.32 40.23 38.29 34.42 41.75 29.15 41.33 39.40 35.52 31.64 41.88 36.63 1.05

1.05 46.30 37.48 46.85 38.58 39.68 43.82 40.78 46.44 44.92 34.71 41.89 45.47 46.02 42.99 36.92 46.57 38.02 44.09 39.12 46.16 45.19 40.22 35.25 32.76 43.26 45.74 41.33 46.30 37.46 44.36 42.43 38.56 45.88 33.29 45.47 43.53 39.66 35.79 46.02 40.76 1.05

Engineering

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. * This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-50

ENGINEERING/TECHNICAL PAGES PT11- 4


315014M

336014M

350014M

385014M

432614M

457814M

495614M

532014M

574014M

616014M

686014M

1.05 53.19 44.37 53.74 45.47 46.57 50.71 47.67 53.33 51.81 41.60 48.78 52.36 52.91 49.88 43.81 53.46 44.91 50.98 46.01 53.05 52.08 47.12 42.14 39.66 50.15 52.64 48.22 53.19 44.35 51.25 49.32 45.45 52.77 40.19 52.36 50.42 46.56 42.68 52.91 47.66 1.05

1.10 57.32 48.50 57.87 49.60 50.70 54.84 51.80 57.46 55.94 45.73 52.91 56.49 57.04 54.01 47.94 57.59 49.04 55.11 50.14 57.18 56.21 51.25 46.28 43.79 54.28 56.77 52.35 57.32 48.48 55.38 53.45 49.59 56.90 44.33 56.49 54.56 50.69 46.82 57.04 51.79 1.10

1.10 60.08 51.26 60.63 52.36 53.46 57.60 54.57 60.22 58.70 48.49 55.67 59.25 59.80 56.77 50.70 60.35 51.80 57.87 52.91 59.94 58.97 54.01 49.04 46.55 57.04 59.53 55.11 60.08 51.24 58.15 56.21 52.35 59.66 47.09 59.25 57.32 53.45 49.58 59.80 54.55 1.10

1.10 66.97 58.14 67.52 59.25 60.35 64.48 61.45 67.10 65.59 55.38 62.55 66.14 66.69 63.66 57.59 67.24 58.69 64.76 59.79 66.83 65.86 60.89 55.92 53.44 63.93 66.41 62.00 66.96 58.13 65.03 63.10 59.23 66.55 53.98 66.13 64.20 60.34 56.47 66.69 61.44 1.10

1.10 76.34 67.51 76.89 68.62 69.72 73.85 70.82 76.47 74.96 64.75 71.92 75.51 76.06 73.03 66.96 76.61 68.06 74.13 69.16 76.20 75.23 70.27 65.30 62.81 73.30 75.78 71.37 76.33 67.50 74.40 72.47 68.61 75.92 63.35 75.50 73.57 69.71 65.84 76.06 70.81 1.10

1.10 81.30 72.48 81.85 73.58 74.68 78.82 75.79 81.44 79.92 69.72 76.89 80.47 81.02 77.99 71.92 81.58 73.03 79.09 74.13 81.16 80.20 75.23 70.26 67.78 78.26 80.75 76.33 81.30 72.47 79.37 77.44 73.57 80.88 68.32 80.47 78.54 74.67 70.81 81.02 75.78 1.10

1.10 88.74 79.92 89.29 81.02 82.12 86.26 83.23 88.88 87.36 77.16 84.33 87.91 88.46 85.43 79.36 89.02 80.47 86.53 81.57 88.60 87.64 82.67 77.70 75.22 85.71 88.19 83.77 88.74 79.91 86.81 84.88 81.01 88.32 75.76 87.91 85.98 82.11 78.25 88.46 83.22 1.10

1.10 95.91 87.08 96.46 88.19 89.29 93.42 90.39 96.04 94.53 84.32 91.49 95.08 95.63 92.60 86.53 96.18 87.63 93.70 88.73 95.77 94.80 89.84 84.87 82.39 92.87 95.35 90.94 95.90 87.08 93.97 92.04 88.18 95.49 82.93 95.08 93.14 89.28 85.42 95.63 90.38 1.10

1.10 104.17 95.35 104.72 96.45 97.55 101.69 98.66 104.31 102.79 92.59 99.76 103.34 103.89 100.86 94.80 104.45 95.90 101.96 97.00 104.03 103.07 98.10 93.14 90.65 101.14 103.62 99.20 104.17 95.34 102.24 100.31 96.44 103.75 91.20 103.34 101.41 97.55 93.68 103.89 98.65 1.10

1.10 112.44 103.62 112.99 104.72 105.82 109.96 106.93 112.58 111.06 100.86 108.03 111.61 112.16 109.13 103.07 112.72 104.17 110.23 105.27 112.30 111.34 106.37 101.41 98.92 109.41 111.89 107.48 112.44 103.61 110.51 108.58 104.72 112.02 99.47 111.61 109.68 105.82 101.95 112.16 106.92 1.10

1.10 126.22 117.40 126.77 118.50 119.60 123.74 120.71 126.36 124.84 114.64 121.81 125.39 125.94 122.91 116.85 126.50 117.95 124.01 119.05 126.08 125.12 120.15 115.19 112.71 123.19 125.67 121.26 126.22 117.39 124.29 122.36 118.50 125.81 113.25 125.39 123.46 119.60 115.73 125.94 120.70 1.10

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. * This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-51

ENGINEERING/TECHNICAL PAGES PT11- 4

Sprockets

1.13 1.13 1.14 1.14 1.15 1.16 1.17 1.17 1.18 1.18 1.18 1.19 1.20 1.20 1.20 1.21 1.21 1.22 1.23 1.24 1.25 1.25 1.25 1.25 1.26 1.27 1.27 1.29 1.29 1.29 1.30 1.31 1.31 1.32 1.33 1.33 1.33 1.33 1.36 1.36

Center Distance, Inches

Conveyor Components

Speed Ratio

Sprocket Combinations Driver Driven Pitch Pitch No. of No. of Dia. Dia. teeth teeth Inches Inches Length Factor* 30 5.263 34 5.965 60 10.527 68 11.930 28 4.912 32 5.614 56 9.825 64 11.229 52 9.123 60 10.527 38 6.667 44 7.720 48 8.421 56 9.825 29 5.088 34 5.965 34 5.965 40 7.018 68 11.930 80 14.036 44 7.720 52 9.123 32 5.614 38 6.667 30 5.263 36 6.316 40 7.018 48 8.421 60 10.527 72 12.632 28 4.912 34 5.965 56 9.825 68 11.930 36 6.316 44 7.720 52 9.123 64 11.229 29 5.088 36 6.316 32 5.614 40 7.018 48 8.421 60 10.527 64 11.229 80 14.036 72 12.632 90 15.790 38 6.667 48 8.421 30 5.263 38 6.667 44 7.720 56 9.825 28 4.912 36 6.316 56 9.825 72 12.632 34 5.965 44 7.720 40 7.018 52 9.123 52 9.123 68 11.930 29 5.088 38 6.667 68 11.930 90 15.790 30 5.263 40 7.018 36 6.316 48 8.421 48 8.421 64 11.229 60 10.527 80 14.036 28 4.912 38 6.667 44 7.720 60 10.527 Length Factor*

Engineering

14MM Pitch HT200 Belt Drive Selection Table

HT Synchrous Belts

DYNA-SYNC

SELECTION


DYNA-SYNC

SELECTION 14MM Pitch HT200 Belt Drive Selection Table Speed Ratio

HT Synchrous Belts Sprockets Conveyor Components

1.37 1.38 1.38 1.39 1.40 1.40 1.41 1.41 1.42 1.43 1.43 1.44 1.46 1.47 1.47 1.50 1.50 1.50 1.50 1.52 1.53 1.54 1.55 1.56 1.56 1.57 1.58 1.60 1.60 1.61 1.63 1.64 1.65 1.65 1.66 1.67 1.67 1.68 1.70 1.71

Sprocket Combinations Driver Driven Pitch Pitch No. of No. of Dia. Dia. Teeth Teeth Inches Inches Length Factor* 38 6.667 52 9.123 32 5.614 44 7.720 29 5.088 40 7.018 52 9.123 72 12.632 40 7.018 56 9.825 80 14.036 112 19.650 64 11.229 90 15.790 34 5.965 48 8.421 48 8.421 68 11.930 28 4.912 40 7.018 56 9.825 80 14.036 36 6.316 52 9.123 44 7.720 64 11.229 30 5.263 44 7.720 38 6.667 56 9.825 32 5.614 48 8.421 40 7.018 60 10.527 48 8.421 72 12.632 60 10.527 90 15.790 29 5.088 44 7.720 34 5.965 52 9.123 52 9.123 80 14.036 44 7.720 68 11.930 36 6.316 56 9.825 72 12.632 112 19.650 28 4.912 44 7.720 38 6.667 60 10.527 30 5.263 48 8.421 40 7.018 64 11.229 56 9.825 90 15.790 32 5.614 52 9.123 44 7.720 72 12.632 34 5.965 56 9.825 68 11.930 112 19.650 29 5.088 48 8.421 36 6.316 60 10.527 48 8.421 80 14.036 38 6.667 64 11.229 40 7.018 68 11.930 28 4.912 48 8.421 Length Factor*

Center Distance, Inches 96614M

119014M

140014M

161014M

177814M

189014M

210014M

231014M

245014M

259014M

280014M

0.80 ... 8.48 9.46 ... ... ... ... ... ... 9.59 ... ... ... 8.73 ... 7.8.7 ... ... ... 8.86 ... ... ... ... ... 8.98 ... 8.11 ... ... ... ... ... ... 8.24 ... ... ... ... 8.36 0.80

0.80 10.95 12.91 13.88 ... 10.10 ... ... 12.06 ... 14.02 ... 11.21 ... 13.17 10.35 12.32 9.48 ... ... 13.30 11.47 ... ... 10.60 ... 13.43 9.73 12.58 ... ... 11.72 ... 10.85 ... 12.71 9.97 ... ... ... 12.83 0.80

0.90 15.11 17.05 18.03 ... 14.26 ... ... 16.21 11.44 18.16 ... 15.37 12.55 17.32 14.52 16.48 13.67 ... ... 17.45 15.63 ... 11.94 14.78 ... 17.58 13.92 16.74 13.06 ... 15.89 11.31 15.03 ... 16.87 14.17 ... 13.31 12.43 17.00 0.90

0.90 19.25 21.20 22.17 14.50 18.41 ... ... 20.36 15.61 22.30 12.78 19.52 16.72 21.46 18.68 20.62 17.83 15.01 ... 21.60 19.78 13.28 16.12 18.94 ... 21.73 18.09 20.89 17.24 ... 20.04 15.52 19.20 ... 21.02 18.35 13.77 17.49 16.63 21.15 0.90

0.95 22.57 24.50 25.47 17.83 21.73 ... ... 23.67 18.94 25.61 16.12 22.83 20.04 24.77 21.99 23.94 21.15 18.34 14.08 24.91 23.10 16.63 19.45 22.25 ... 25.04 21.41 24.20 20.56 14.58 23.36 18.86 22.52 ... 24.33 21.67 17.13 20.82 19.97 24.47 0.95

0.95 24.77 26.71 27.68 20.04 23.94 ... 15.82 25.88 21.15 27.82 18.34 25.04 22.25 26.98 24.20 26.14 23.36 20.56 16.32 27.11 25.31 18.86 21.67 24.46 ... 27.25 23.62 26.41 22.78 16.82 25.57 21.08 24.73 ... 26.54 23.88 19.36 23.04 22.19 26.68 0.95

1.00 28.91 30.85 31.82 24.19 28.08 ... 19.99 30.02 25.30 31.95 22.50 29.18 26.40 31.12 28.34 30.28 27.50 24.72 20.50 31.25 29.45 23.02 25.82 28.61 ... 31.39 27.77 30.55 26.93 21.01 29.71 25.24 28.87 ... 30.68 28.03 23.53 27.19 26.34 30.82 1.00

1.00 33.05 34.98 35.95 28.33 32.21 18.80 24.14 34.15 29.43 36.08 26.65 33.31 30.54 35.25 32.48 34.42 31.64 28.86 24.66 35.39 33.58 27.17 29.96 32.75 19.80 35.52 31.91 34.69 31.07 25.18 33.85 29.38 33.01 20.30 34.82 32.17 27.69 31.33 30.49 34.95 1.00

1.00 35.81 37.74 38.71 31.09 34.97 21.59 26.91 36.91 32.20 38.85 29.41 36.08 33.30 38.01 35.24 37.18 34.41 31.62 27.43 38.15 36.35 29.94 32.73 35.51 22.60 38.28 34.67 37.45 33.83 27.95 36.61 32.15 35.78 23.10 37.58 34.94 30.46 34.10 33.26 37.72 1.00

1.05 38.56 40.50 41.47 33.85 37.73 24.37 29.68 39.67 34.96 41.60 32.18 38.83 36.06 40.77 38.00 39.94 37.16 34.39 30.20 40.90 39.10 32.70 35.49 38.27 25.39 41.04 37.43 40.21 36.59 30.72 39.37 34.91 38.54 25.89 40.34 37.70 33.23 36.86 36.02 40.48 1.05

1.05 42.70 44.64 45.60 37.99 41.87 28.52 33.82 43.80 39.10 45.74 36.32 42.97 40.20 44.91 42.14 44.07 41.30 38.53 34.35 45.04 43.24 36.85 39.63 42.41 29.56 45.18 41.57 44.34 40.73 34.87 43.51 39.06 42.67 30.07 44.48 41.84 37.38 41.00 40.16 44.61 1.05

Engineering

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. * This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-52

ENGINEERING/TECHNICAL PAGES PT11- 4


315014M

336014M

350014M

385014M

432614M

457814M

495614M

532014M

574014M

616014M

686014M

1.05 49.59 51.53 52.49 44.89 48.76 35.44 40.73 50.70 45.99 52.63 43.22 49.86 47.09 51.80 49.03 50.97 48.20 45.43 41.26 51.93 50.14 43.75 46.53 49.30 36.49 52.07 48.47 51.24 47.63 41.79 50.41 45.96 49.57 37.01 51.37 48.74 44.28 47.90 47.06 51.51 1.05

1.10 53.72 55.66 56.62 49.02 52.89 39.58 44.86 54.83 50.13 56.76 47.35 54.00 51.23 55.93 53.16 55.10 52.33 49.56 45.39 56.07 54.27 47.89 50.66 53.43 40.63 56.20 52.60 55.37 51.77 45.93 54.54 50.10 53.70 41.16 55.51 52.87 48.42 52.03 51.20 55.64 1.10

1.10 56.49 58.42 59.38 51.78 55.65 42.35 47.62 57.59 52.89 59.52 50.12 56.76 53.99 58.69 55.92 57.86 55.09 52.32 48.16 58.83 57.03 50.65 53.43 56.20 43.40 58.96 55.36 58.13 54.53 48.69 57.30 52.86 56.47 43.93 58.27 55.63 51.19 54.80 53.96 58.40 1.10

1.10 63.37 65.30 66.27 58.67 62.54 49.25 54.52 64.47 59.78 66.41 57.01 63.64 60.88 65.58 62.81 64.75 61.98 59.21 55.05 65.71 63.92 57.54 60.32 63.08 50.31 65.85 62.25 65.02 61.42 55.59 64.19 59.75 63.35 50.84 65.15 62.52 58.08 61.69 60.85 65.29 1.10

1.10 72.74 74.68 75.64 68.05 71.91 58.63 63.89 73.85 69.15 75.78 66.38 73.02 70.25 74.95 72.18 74.12 71.35 68.59 64.43 75.08 73.29 66.92 69.69 72.46 59.70 75.22 71.62 74.39 70.79 64.97 73.56 69.13 72.73 60.23 74.53 71.90 67.46 71.06 70.23 74.66 1.10

1.10 77.71 79.64 80.61 73.01 76.88 63.60 68.86 78.81 74.12 80.74 71.35 77.98 75.22 79.91 77.15 79.08 76.32 73.55 69.40 80.05 78.25 71.89 74.66 77.42 64.67 80.19 76.59 79.36 75.76 69.94 78.53 74.09 77.69 65.20 79.49 76.86 72.43 76.03 75.20 79.63 1.10

1.10 85.15 87.08 88.05 80.45 84.32 71.05 76.31 86.25 81.56 88.18 78.79 85.42 82.66 87.35 84.59 86.53 83.76 81.00 76.85 87.49 85.70 79.33 82.10 84.86 72.12 87.63 84.03 86.80 83.20 77.38 85.97 81.54 85.14 72.65 86.93 84.31 79.87 83.47 82.64 87.07 1.10

1.10 92.32 94.25 95.21 87.62 91.49 78.22 83.47 93.42 88.72 95.35 85.96 92.59 89.83 94.52 91.76 93.69 90.93 88.16 84.01 94.66 92.86 86.50 89.27 92.03 79.29 94.79 91.20 93.96 90.37 84.55 93.13 88.71 92.30 79.83 94.10 91.47 87.04 90.64 89.81 94.24 1.10

1.10 100.58 102.51 103.48 95.89 99.75 86.49 91.74 101.68 96.99 103.61 94.23 100.85 98.09 102.79 100.02 101.96 99.19 96.43 92.28 102.92 101.13 94.77 97.53 100.30 87.57 103.06 99.47 102.23 98.64 92.82 101.40 96.97 100.57 88.10 102.37 99.74 95.31 98.91 98.08 102.50 1.10

1.10 108.85 110.78 111.75 104.16 108.02 94.76 100.01 109.95 105.26 111.89 102.50 109.13 106.36 111.06 108.30 110.23 107.47 104.70 100.56 111.19 109.40 103.04 105.81 108.57 95.84 111.33 107.74 110.50 106.91 101.10 109.67 105.25 108.84 96.38 110.64 108.01 103.58 107.18 106.35 110.77 1.10

1.10 122.63 124.56 125.53 117.94 121.80 108.55 113.80 123.74 119.04 125.67 116.28 122.91 120.14 124.84 122.08 124.01 121.25 118.49 114.34 124.97 123.18 116.83 119.59 122.35 109.63 125.11 121.52 124.28 120.69 114.88 123.45 119.03 122.62 110.17 124.42 121.79 117.37 120.96 120.13 124.56 1.10

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. * This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-53

ENGINEERING/TECHNICAL PAGES PT11- 4

Sprockets

1.37 1.38 1.38 1.39 1.40 1.40 1.41 1.41 1.42 1.43 1.43 1.44 1.46 1.47 1.47 1.50 1.50 1.50 1.50 1.52 1.53 1.54 1.55 1.56 1.56 1.57 1.58 1.60 1.60 1.61 1.63 1.64 1.65 1.65 1.66 1.67 1.67 1.68 1.70 1.71

Center Distance, Inches

Conveyor Components

Speed Ratio

Sprocket Combinations Driver Driven Pitch Pitch No. of No. of Dia. Dia. teeth teeth Inches Inches Length Factor* 38 6.667 52 9.123 32 5.614 44 7.720 29 5.088 40 7.018 52 9.123 72 12.632 40 7.018 56 9.825 80 14.036 112 19.650 64 11.229 90 15.790 34 5.965 48 8.421 48 8.421 68 11.930 28 4.912 40 7.018 56 9.825 80 14.036 36 6.316 52 9.123 44 7.720 64 11.229 30 5.263 44 7.720 38 6.667 56 9.825 32 5.614 48 8.421 40 7.018 60 10.527 48 8.421 72 12.632 60 10.527 90 15.790 29 5.088 44 7.720 34 5.965 52 9.123 52 9.123 80 14.036 44 7.720 68 11.930 36 6.316 56 9.825 72 12.632 112 19.650 28 4.912 44 7.720 38 6.667 60 10.527 30 5.263 48 8.421 40 7.018 64 11.229 56 9.825 90 15.790 32 5.614 52 9.123 44 7.720 72 12.632 34 5.965 56 9.825 68 11.930 112 19.650 29 5.088 48 8.421 36 6.316 60 10.527 48 8.421 80 14.036 38 6.667 64 11.229 40 7.018 68 11.930 28 4.912 48 8.421 Length Factor*

Engineering

14MM Pitch HT200 Belt Drive Selection Table

HT Synchrous Belts

DYNA-SYNC

SELECTION


DYNA-SYNC

SELECTION 14MM Pitch HT200 Belt Drive Selection Table Speed Ratio

HT Synchrous Belts Sprockets Conveyor Components

1.73 1.73 1.75 1.75 1.77 1.78 1.79 1.79 1.80 1.80 1.82 1.86 1.87 1.87 1.88 1.88 1.88 1.89 1.90 1.93 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.05 2.07 2.10 2.11 2.12 2.12 2.13 2.13 2.14 2.15 2.21 2.22

Sprocket Combinations Driver Driven Pitch Pitch No. of No. of Dia. Dia. Teeth Teeth Inches Inches Length Factor* 52 9.123 90 15.790 30 5.263 52 9.123 32 5.614 56 9.825 64 11.229 112 19.650 34 5.965 60 10.527 36 6.316 64 11.229 38 6.667 68 11.930 29 5.088 52 9.123 40 7.018 72 12.632 80 14.036 144 25.264 44 7.720 80 14.036 28 4.912 52 9.123 30 5.263 56 9.825 60 10.527 112 19.650 32 5.614 60 10.527 48 8.421 90 15.790 34 5.965 64 11.229 36 6.316 68 11.930 38 6.667 72 12.632 29 5.088 56 9.825 28 4.912 56 9.825 30 5.263 60 10.527 32 5.614 64 11.229 34 5.965 68 11.930 36 6.316 72 12.632 40 7.018 80 14.036 56 9.825 112 19.650 72 12.632 144 25.264 44 7.720 90 15.790 29 5.088 60 10.527 80 14.036 168 29.475 38 6.667 80 14.036 34 5.965 72 12.632 68 11.930 144 25.264 32 5.614 68 11.930 30 5.263 64 11.229 28 4.912 60 10.527 52 9.123 112 19.650 29 5.088 64 11.229 36 6.316 80 14.036 Length Factor*

Center Distance, Inches 96614M

119014M

140014M

161014M

177814M

189014M

210014M

231014M

245014M

259014M

280014M

0.80 ... ... ... ... ... ... ... ... ... ... ... 7.70 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0.80

0.80 ... 11.97 11.10 ... 10.22 ... ... 12.10 ... ... ... 12.22 11.34 ... 10.46 ... 9.56 ... ... 11.47 11.59 10.70 9.79 ... ... ... ... ... ... 10.82 ... ... ... ... ... 10.03 10.94 ... 10.14 ... 0.80

0.90 ... 16.15 15.29 ... 14.43 13.56 12.68 16.27 11.79 ... ... 16.40 15.54 ... 14.68 ... 13.80 12.92 12.03 15.67 15.79 14.93 14.05 13.17 12.27 ... ... ... ... 15.05 ... ... 12.51 ... 13.41 14.29 15.17 ... 14.42 10.88 0.90

0.90 ... 20.30 19.46 ... 18.60 17.74 16.88 20.43 16.02 ... 14.26 20.56 19.71 ... 18.86 ... 18.00 17.13 16.26 19.84 19.97 19.11 18.25 17.38 16.51 14.74 ... ... 12.58 19.24 ... 14.98 16.76 ... 17.63 18.50 19.37 ... 18.63 15.22 0.90

0.95 15.06 23.62 22.78 ... 21.93 21.08 20.22 23.75 19.36 ... 17.63 23.88 23.04 ... 22.19 15.55 21.33 20.48 19.62 23.17 23.30 22.44 21.59 20.73 19.87 18.12 ... ... 16.02 22.57 ... 18.37 20.12 ... 20.98 21.84 22.70 ... 21.97 18.61 0.95

0.95 17.32 25.83 24.99 ... 24.14 23.30 22.44 25.97 21.59 ... 19.87 26.10 25.25 ... 24.40 17.81 23.55 22.70 21.84 25.38 25.51 24.66 23.81 22.96 22.10 20.37 ... ... 18.29 24.79 ... 20.61 22.35 ... 23.21 24.07 24.92 ... 24.19 20.86 0.95

1.00 21.51 29.98 29.14 16.55 28.30 27.45 26.60 30.11 25.75 ... 24.05 30.24 29.40 17.02 28.56 22.02 27.71 26.86 26.01 29.53 29.66 28.82 27.97 27.12 26.27 24.55 17.50 ... 22.51 28.95 ... 24.81 26.52 ... 27.38 28.23 29.08 17.97 28.36 25.06 1.00

1.00 25.69 34.12 33.28 20.79 32.44 31.59 30.75 34.25 29.91 ... 28.21 34.38 33.54 21.28 32.70 26.20 31.86 31.01 30.17 33.67 33.81 32.96 32.12 31.27 30.42 28.72 21.76 ... 26.70 33.09 ... 28.98 30.68 ... 31.53 32.38 33.23 22.25 32.51 29.23 1.00

1.00 28.47 36.88 36.04 23.60 35.20 34.36 33.52 37.01 32.68 ... 30.98 37.15 36.31 24.10 35.47 28.98 34.63 33.78 32.94 36.44 36.57 35.73 34.89 34.04 33.20 31.50 24.59 ... 29.49 35.86 ... 31.76 33.46 ... 34.31 35.15 35.99 25.08 35.28 32.01 1.00

1.05 31.24 39.64 38.80 26.40 37.96 37.12 36.28 39.77 35.44 ... 33.75 39.91 39.07 26.90 38.23 31.76 37.39 36.55 35.70 39.20 39.33 38.49 37.65 36.81 35.96 34.27 27.39 20.23 32.27 38.63 ... 34.53 36.23 20.69 37.07 37.91 38.76 27.89 38.05 34.79 1.05

1.05 35.40 43.78 42.94 30.58 42.11 41.27 40.43 43.91 39.59 23.58 37.90 44.05 43.21 31.08 42.37 35.92 41.53 40.69 39.85 43.34 43.48 42.64 41.80 40.96 40.11 38.42 31.59 24.54 36.43 42.77 ... 38.68 40.38 25.01 41.22 42.06 42.90 32.09 42.19 38.94 1.05

Engineering

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. * This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-54

ENGINEERING/TECHNICAL PAGES PT11- 4


315014M

336014M

350014M

385014M

432614M

457814M

495614M

532014M

574014M

616014M

686014M

1.05 42.31 50.67 49.84 37.52 49.00 48.17 47.33 50.81 46.49 30.63 44.81 50.94 50.11 38.04 49.27 42.84 48.43 47.60 46.76 50.24 50.38 49.54 48.70 47.86 47.02 45.34 38.55 31.61 43.36 49.67 26.71 45.60 47.29 32.10 48.13 48.97 49.81 39.06 49.10 45.86 1.05

1.10 46.45 54.81 53.97 41.67 53.14 52.30 51.47 54.94 50.63 34.82 48.95 55.08 54.24 42.19 53.41 46.98 52.57 51.73 50.90 54.38 54.51 53.67 52.84 52.00 51.16 49.48 42.71 35.82 47.50 53.81 31.00 49.74 51.43 36.31 52.27 53.10 53.94 43.22 53.24 50.01 1.10

1.10 49.22 57.57 56.74 44.45 55.90 55.07 54.23 57.70 53.39 37.61 51.72 57.84 57.00 44.97 56.17 49.75 55.33 54.50 53.66 57.14 57.27 56.44 55.60 54.76 53.93 52.25 45.48 38.62 50.27 56.57 33.84 52.51 54.19 39.12 55.03 55.87 56.70 46.00 56.00 52.77 1.10

1.10 56.12 64.46 63.62 51.36 62.79 61.96 61.12 64.59 60.29 44.56 58.61 64.73 63.89 51.88 63.06 56.65 62.23 61.39 60.55 64.03 64.16 63.33 62.49 61.66 60.82 59.15 52.40 45.58 57.18 63.46 40.88 59.41 61.09 46.09 61.93 62.76 63.60 52.92 62.89 59.68 1.10

1.10 65.50 73.83 73.00 60.76 72.17 71.33 70.50 73.97 69.67 54.00 67.99 74.10 73.27 61.28 72.44 66.04 71.60 70.77 69.93 73.40 73.54 72.71 71.87 71.04 70.20 68.53 61.81 55.03 66.57 72.84 50.39 68.80 70.47 55.54 71.31 72.14 72.98 62.33 72.27 69.06 1.10

1.10 70.47 78.80 77.97 65.73 77.13 76.30 75.47 78.93 74.63 58.99 72.96 79.07 78.24 66.26 77.40 71.01 76.57 75.74 74.90 78.37 78.51 77.67 76.84 76.01 75.17 73.50 66.79 60.02 71.54 77.81 55.41 73.77 75.44 60.54 76.28 77.11 77.94 67.32 77.24 74.03 1.10

1.10 77.92 86.24 85.41 73.19 84.58 83.74 82.91 86.38 82.08 66.46 80.41 86.51 85.68 73.72 84.85 78.46 84.01 83.18 82.35 85.81 85.95 85.12 84.28 83.45 82.62 80.95 74.25 67.50 78.99 85.25 62.91 81.22 82.89 68.02 83.72 84.55 85.39 74.78 84.69 81.48 1.10

1.10 85.09 93.41 92.58 80.36 91.74 90.91 90.08 93.54 89.25 73.64 87.58 93.68 92.85 80.90 92.02 85.63 91.18 90.35 89.52 92.98 93.12 92.29 91.45 90.62 89.79 88.12 81.43 74.69 86.17 92.42 70.13 88.39 90.06 75.22 90.89 91.72 92.56 81.96 91.86 88.66 1.10

1.10 93.36 101.67 100.84 88.64 100.01 99.18 98.35 101.81 97.52 81.93 95.85 101.95 101.11 89.17 100.28 93.90 99.45 98.62 97.79 101.25 101.39 100.55 99.72 98.89 98.06 96.39 89.71 82.99 94.44 100.69 78.44 96.66 98.33 83.51 99.16 99.99 100.83 90.24 100.13 96.93 1.10

1.10 101.64 109.94 109.11 96.92 108.28 107.45 106.62 110.08 105.79 90.22 104.12 110.22 109.39 97.45 108.56 102.18 107.72 106.89 106.06 109.52 109.66 108.83 108.00 107.16 106.33 104.67 97.99 91.28 102.72 108.96 86.74 104.94 106.60 91.81 107.43 108.27 109.10 98.52 108.40 105.20 1.10

1.10 115.43 123.73 122.90 110.71 122.07 121.24 120.41 123.86 119.57 104.02 117.91 124.00 123.17 111.25 122.34 115.97 121.51 120.68 119.85 123.30 123.44 122.61 121.78 120.95 120.12 118.45 111.78 105.09 116.51 122.75 100.57 118.72 120.39 105.62 121.22 122.05 122.88 112.32 122.19 118.99 1.10

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. * This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-55

ENGINEERING/TECHNICAL PAGES PT11- 4

Sprockets

1.73 1.73 1.75 1.75 1.77 1.78 1.79 1.79 1.80 1.80 1.82 1.86 1.87 1.87 1.88 1.88 1.88 1.89 1.90 1.93 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.00 2.05 2.07 2.10 2.11 2.12 2.12 2.13 2.13 2.14 2.15 2.21 2.22

Center Distance, Inches

Conveyor Components

Speed Ratio

Sprocket Combinations Driver Driven Pitch Pitch No. of No. of Dia. Dia. teeth teeth Inches Inches Length Factor* 52 9.123 90 15.790 30 5.263 52 9.123 32 5.614 56 9.825 64 11.229 112 19.650 34 5.965 60 10.527 36 6.316 64 11.229 38 6.667 68 11.930 29 5.088 52 9.123 40 7.018 72 12.632 80 14.036 144 25.264 44 7.720 80 14.036 28 4.912 52 9.123 30 5.263 56 9.825 60 10.527 112 19.650 32 5.614 60 10.527 48 8.421 90 15.790 34 5.965 64 11.229 36 6.316 68 11.930 38 6.667 72 12.632 29 5.088 56 9.825 28 4.912 56 9.825 30 5.263 60 10.527 32 5.614 64 11.229 34 5.965 68 11.930 36 6.316 72 12.632 40 7.018 80 14.036 56 9.825 112 19.650 72 12.632 144 25.264 44 7.720 90 15.790 29 5.088 60 10.527 80 14.036 168 29.475 38 6.667 80 14.036 34 5.965 72 12.632 68 11.930 144 25.264 32 5.614 68 11.930 30 5.263 64 11.229 28 4.912 60 10.527 52 9.123 112 19.650 29 5.088 64 11.229 36 6.316 80 14.036 Length Factor*

Engineering

14MM Pitch HT200 Belt Drive Selection Table

HT Synchrous Belts

DYNA-SYNC

SELECTION


DYNA-SYNC

SELECTION 14MM Pitch HT200 Belt Drive Selection Table Speed Ratio

HT Synchrous Belts Sprockets Conveyor Components

2.25 2.25 2.25 2.27 2.29 2.33 2.33 2.35 2.35 2.37 2.40 2.40 2.40 2.43 2.47 2.48 2.50 2.50 2.55 2.57 2.57 2.63 2.65 2.67 2.67 2.70 2.76 2.77 2.80 2.80 2.81 2.82 2.86 2.95 3.00 3.00 3.00 3.00 3.00 3.10 3.11 3.20

Sprocket Combinations Driver Driven Pitch Pitch No. of No. of Dia. Dia. Teeth Teeth Inches Inches Length Factor* 32 5.614 72 12.632 40 7.018 90 15.790 64 11.229 144 25.264 30 5.263 68 11.930 28 4.912 64 11.229 48 8.421 112 19.650 72 12.632 168 29.475 29 5.088 68 11.930 34 5.965 80 14.036 38 6.667 90 15.790 30 5.263 72 12.632 60 10.527 144 25.264 80 14.036 192 33.686 28 4.912 68 11.930 68 11.930 168 29.475 29 5.088 72 12.632 32 5.614 80 14.036 36 6.316 90 15.790 44 7.720 112 19.650 28 4.912 72 12.632 56 9.825 144 25.264 64 11.229 168 29.475 34 5.965 90 15.790 30 5.263 80 14.036 72 12.632 192 33.686 80 14.036 216 37.896 29 5.088 80 14.036 52 9.123 144 25.264 40 7.018 112 19.650 60 10.527 168 29.475 32 5.614 90 15.790 68 11.930 192 33.686 28 4.912 80 14.036 38 6.667 112 19.650 30 5.263 90 15.790 48 8.421 144 25.264 56 9.825 168 29.475 64 11.229 192 33.686 72 12.632 216 37.896 29 5.088 90 15.790 36 6.316 112 19.650 60 10.527 192 33.686 Length Factor*

Center Distance, Inches 96614M

119014M

140014M

161014M

177814M

189014M

210014M

231014M

245014M

259014M

280014M

0.80 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0.80

0.80 ... ... ... 9.32 10.26 ... ... 9.43 ... ... ... ... ... 9.54 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0.80

0.90 12.74 ... ... 13.65 14.54 ... ... 13.77 11.11 ... 12.98 ... ... 13.89 ... 13.10 11.34 ... ... 13.21 ... ... ... 11.56 ... ... 11.67 ... ... ... ... ... 11.78 ... ... ... ... ... ... ... ... ... 0.90

0.90 17.00 13.04 ... 17.88 18.75 ... ... 18.00 15.46 13.27 17.25 ... ... 18.13 ... 17.37 15.69 13.49 ... 17.49 ... ... 13.72 15.93 ... ... 16.05 ... ... ... 13.95 ... 16.17 ... 14.17 ... ... ... ... 14.28 ... ... 0.90

0.95 20.37 16.50 ... 21.23 22.10 ... ... 21.36 18.86 16.74 20.62 ... ... 21.49

0.95 22.60 18.78 ... 23.46 24.32 ... ... 23.59 21.11 19.02 22.85 ... ... 23.72

1.00 26.78 23.01 ... 27.64 28.49 18.43 ... 27.76 25.31 23.25 27.03 ... ... 27.89

1.00 30.94 27.20 ... 31.79 32.64 22.73 ... 31.92 29.48 27.45 31.20 ... ... 32.05

1.00 33.72 30.00 ... 34.57 35.41 25.56 ... 34.70 32.27 30.25 33.98 18.64 ... 34.83

1.05 36.49 32.78 21.15 37.33 38.18 28.38 ... 37.46 35.04 33.03 36.75 21.61 ... 37.59

1.05 40.64 36.95 25.49 41.48 42.32 32.59 ... 41.61 39.20 37.20 40.90 25.96 ... 41.74

20.74 19.10 16.97 ... 20.86 ... ... 17.21 19.34 ... ... 19.46 ... ... ... 17.44 ... 19.58 ... 17.68 ... ... ... ... 17.79 ... ... 0.95

22.98 21.36 19.26 14.46 23.10 ... ... 19.50 21.60 ... ... 21.72 ... 14.90 ... 19.73 ... 21.85 15.12 19.97 ... ... ... ... 20.09 15.34 ... 0.95

27.16 25.56 23.50 18.89 27.29 ... ... 23.74 25.81 ... ... 25.93 ... 19.36 ... 23.99 ... 26.06 19.58 24.23 ... ... ... ... 24.35 19.81 ... 1.00

31.33 29.74 27.70 23.20 31.45 ... ... 27.95 29.99 ... ... 30.12 ... 23.68 ... 28.20 ... 30.24 23.91 28.45 ... ... ... ... 28.57 24.15 ... 1.00

34.10 32.52 30.50 26.05 34.23 19.09 ... 30.75 32.78 ... ... 32.91 19.53 26.53 ... 31.00 ... 33.03 26.77 31.25 19.97 ... ... ... 31.38 27.01 ... 1.00

36.87 35.30 33.29 28.87 37.00 22.06 ... 33.54 35.56 ... ... 35.68 22.51 29.36 ... 33.79 ... 35.81 29.60 34.04 22.97 ... ... ... 34.17 29.84 ... 1.05

41.03 39.46 37.46 33.08 41.16 26.43 21.15 37.71 39.72 ... ... 39.85 26.89 33.58 21.59 37.97 ... 39.98 33.83 38.22 27.36 22.02 ... ... 38.35 34.07 ... 1.05

Engineering

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. * This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-56

ENGINEERING/TECHNICAL PAGES PT11- 4


315014M

336014M

350014M

385014M

432614M

457814M

495614M

532014M

574014M

616014M

686014M

1.05 47.55 43.88 32.59 48.39 49.23 39.56 27.65 48.52 46.12 44.14 47.81 33.08 --48.66 28.11 47.94 46.39 44.40 40.07 48.08 33.56 28.57 44.65 46.65 ----46.78 34.04 40.57 29.03 44.91 23.63 46.91 40.82 45.17 34.52 29.49 24.14 --45.30 41.07 24.49 1.05

1.10 51.69 48.03 36.81 52.53 53.37 43.73 31.95 52.66 50.27 48.29 51.95 37.30 26.89 52.80 32.43 52.09 50.53 48.55 44.24 52.22 37.79 32.90 48.81 50.79 27.79 22.16 50.92 38.28 44.75 33.37 49.07 28.19 51.05 45.00 49.32 38.77 33.84 28.69 23.01 49.45 45.25 29.08 1.10

1.10 54.46 50.80 39.62 55.30 56.13 46.51 34.81 55.43 53.04 51.06 54.72 40.11 29.82 55.56 35.28 54.85 53.30 51.32 47.02 54.99 40.61 35.76 51.58 53.56 30.74 25.32 53.69 41.10 47.53 36.24 51.84 31.15 53.82 47.79 52.10 41.59 36.71 31.65 26.19 52.23 48.04 32.06 1.10

1.10 61.35 57.70 46.59 62.19 63.03 53.44 41.86 62.33 59.94 57.97 61.62 47.10 37.02 62.46 42.35 61.75 60.20 58.23 53.96 61.89 47.60 42.84 58.49 60.47 37.97 32.85 60.60 48.10 54.47 43.33 58.75 38.41 60.73 54.73 59.02 48.60 43.81 38.91 33.76 59.15 54.99 39.34 1.10

1.10 70.74 67.10 56.05 71.57 72.41 62.86 51.39 71.71 69.33 67.36 71.00 56.56 46.66 71.84 51.89 71.14 69.59 67.63 63.38 71.27 57.07 52.39 67.89 69.86 47.63 42.73 69.99 57.58 63.90 52.89 68.15 48.09 70.12 64.16 68.42 58.09 53.38 48.60 43.67 68.55 64.42 49.06 1.10

1.10 75.71 72.07 61.05 76.54 77.38 67.84 56.42 76.68 74.30 72.34 75.98 61.57 51.72 76.81 56.92 76.11 74.57 72.60 68.36 76.24 62.08 57.42 72.87 74.83 52.71 47.86 74.97 62.59 68.89 57.93 73.13 53.18 75.10 69.15 73.40 63.10 58.43 53.69 48.82 73.53 69.41 54.15 1.10

1.10 83.16 79.53 68.54 83.99 84.82 75.30 63.93 84.12 81.75 79.79 83.42 69.06 59.28 84.26 64.44 83.56 82.02 80.06 75.83 83.69 69.57 64.95 80.32 82.29 60.28 55.51 82.42 70.09 76.35 65.46 80.59 60.76 82.55 76.62 80.85 70.60 65.96 61.27 56.48 80.99 76.88 61.75 1.10

1.10 90.33 86.70 75.74 91.16 91.99 82.49 71.16 91.29 88.92 86.97 90.60 76.26 66.54 91.43 71.67 90.73 89.19 87.23 83.01 90.86 76.78 72.18 87.50 89.46 67.54 62.82 89.59 77.30 83.54 72.69 87.77 68.03 89.73 83.80 88.03 77.81 73.20 68.55 63.81 88.17 84.07 69.03 1.10

1.10 98.60 94.98 84.04 99.43 100.26 90.77 79.47 99.57 97.20 95.24 98.87 84.56 74.89 99.70 79.99 99.00 97.47 95.51 91.30 99.14 85.08 80.50 95.78 97.73 75.90 72.23 97.87 85.60 91.83 81.02 96.04 76.39 98.00 92.09 96.31 86.12 81.53 76.91 72.22 96.44 92.36 77.40 1.10

1.10 106.87 103.25 92.33 107.71 108.54 99.05 87.78 107.84 105.47 103.52 107.14 92.86 83.22 107.98 88.30 107.28 105.74 103.79 99.58 107.41 93.38 88.82 104.06 106.01 84.24 79.60 106.15 93.91 100.12 89.34 104.33 84.73 106.28 100.38 104.59 94.43 89.86 85.26 80.61 104.73 100.65 85.75 1.10

1.10 120.66 117.04 106.15 121.49 122.32 112.85 101.62 121.63 119.26 117.31 120.93 106.68 97.08 121.76 102.14 121.06 119.53 117.58 113.39 121.20 107.20 102.67 117.85 119.80 98.12 93.51 119.94 107.73 113.92 103.19 118.12 98.61 120.07 114.19 118.39 108.26 103.71 99.15 94.53 118.52 114.45 99.64 1.10

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. * This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-57

ENGINEERING/TECHNICAL PAGES PT11- 4

Sprockets

2.25 2.25 2.25 2.27 2.29 2.33 2.33 2.35 2.35 2.37 2.40 2.40 2.40 2.43 2.47 2.48 2.50 2.50 2.55 2.57 2.57 2.63 2.65 2.67 2.67 2.70 2.76 2.77 2.80 2.80 2.81 2.82 2.86 2.95 3.00 3.00 3.00 3.00 3.00 3.10 3.11 3.20

Center Distance, Inches

Conveyor Components

Speed Ratio

Sprocket Combinations Driver Driven Pitch Pitch No. of No. of Dia. Dia. teeth teeth Inches Inches Length Factor* 32 5.614 72 12.632 40 7.018 90 15.790 64 11.229 144 25.264 30 5.263 68 11.930 28 4.912 64 11.229 48 8.421 112 19.650 72 12.632 168 29.475 29 5.088 68 11.930 34 5.965 80 14.036 38 6.667 90 15.790 30 5.263 72 12.632 60 10.527 144 25.264 80 14.036 192 33.686 28 4.912 68 11.930 68 11.930 168 29.475 29 5.088 72 12.632 32 5.614 80 14.036 36 6.316 90 15.790 44 7.720 112 19.650 28 4.912 72 12.632 56 9.825 144 25.264 64 11.229 168 29.475 34 5.965 90 15.790 30 5.263 80 14.036 72 12.632 192 33.686 80 14.036 216 37.896 29 5.088 80 14.036 52 9.123 144 25.264 40 7.018 112 19.650 60 10.527 168 29.475 32 5.614 90 15.790 68 11.930 192 33.686 28 4.912 80 14.036 38 6.667 112 19.650 30 5.263 90 15.790 48 8.421 144 25.264 56 9.825 168 29.475 64 11.229 192 33.686 72 12.632 216 37.896 29 5.088 90 15.790 36 6.316 112 19.650 60 10.527 192 33.686 Length Factor*

Engineering

14MM Pitch HT200 Belt Drive Selection Table

HT Synchrous Belts

DYNA-SYNC

SELECTION


DYNA-SYNC

SELECTION 14MM Pitch HT200 Belt Drive Selection Table Speed Ratio

HT Synchrous Belts Sprockets Conveyor Components

3.21 3.23 3.27 3.29 3.38 3.43 3.50 3.50 3.60 3.69 3.73 3.79 3.82 3.86 3.86 4.00 4.00 4.00 4.20 4.24 4.36 4.42 4.50 4.50 4.67 4.80 4.80 4.91 4.94 4.97 5.05 5.14 5.25 5.33 5.40 5.60 5.65 5.65 5.79 6.00 6.00 6.00 6.35 6.40 6.62 6.75 6.86

Engineering

Sprocket Combinations Driver Driven Pitch Pitch No. of No. of Dia. Dia. Teeth Teeth Inches Inches Length Factor* 28 4.912 90 15.790 52 9.123 168 29.475 44 7.720 144 25.264 34 5.965 112 19.650 64 11.229 216 37.896 56 9.825 192 33.686 32 5.614 112 19.650 48 8.421 168 29.475 40 7.018 144 25.264 52 9.123 192 33.686 30 5.263 112 19.650 38 6.667 144 25.264 44 7.720 168 29.475 29 5.088 112 19.650 56 9.825 216 37.896 28 4.912 112 19.650 36 6.316 144 25.264 48 8.421 192 33.686 40 7.018 168 29.475 34 5.965 144 25.264 44 7.720 192 33.686 38 6.667 168 29.475 32 5.614 144 25.264 48 8.421 216 37.896 36 6.316 168 29.475 30 5.263 144 25.264 40 7.018 192 33.686 44 7.720 216 37.896 34 5.965 168 29.475 29 5.088 144 25.264 38 6.667 192 33.686 28 4.912 144 25.264 32 5.614 168 29.475 36 6.316 192 33.686 40 7.018 216 37.896 30 5.263 168 29.475 34 5.965 192 33.686 38 6.667 216 37.896 29 5.088 168 29.475 28 4.912 168 29.475 32 5.614 192 33.686 36 6.316 216 37.896 34 5.965 216 37.896 30 5.263 192 33.686 29 5.088 192 33.686 32 5.614 216 37.896 28 4.912 192 33.686 Length Factor*

Center Distance, Inches 96614M

119014M

140014M

161014M

177814M

189014M

210014M

231014M

245014M

259014M

280014M

0.80 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0.80

0.80 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0.80

0.90 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0.90

0.90 14.40 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0.90

0.95 17.91 ... ... ... ... ... 13.25 ... ... ... 13.46 ... ... 13.57 ... 13.67 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0.95

0.95 20.21 ... ... 15.56 ... ... 15.77 ... ... ... 15.99 ... ... 16.10 ... 16.21 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0.95

1.00 24.47 ... ... 20.04 ... ... 20.27 ... ... ... 20.50 ... ... 20.61 ... 20.72 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 1.00

1.00 28.69 ... 17.29 24.39 ... ... 24.62 ... 17.71 ... 24.85 17.92 ... 24.97 ... 25.09 18.13 ... ... 18.34 ... ... 18.55 ... ... 18.76 ... ... ... 18.86 ... 18.97 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 1.00

1.00 31.50 ... 20.41 27.25 ... ... 27.49 ... 20.85 ... 27.72 21.06 ... 27.84 ... 27.96 21.28 ... ... 21.50 ... ... 21.72 ... ... 21.93 ... ... ... 22.04 ... 22.15 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 1.00

1.05 34.29 ... 23.42 30.09 ... ... 30.33 ... 23.86 ... 30.57 24.09 ... 30.69 ... 30.81 24.31 ... 18.87 24.53 ... 19.08 24.76 ... 19.28 24.98 ... ... 19.48 25.09 ... 25.20 19.69 ... ... 19.89 ... ... 19.99 20.09 ... ... ... ... ... ... ... 1.05

1.05 38.48 22.46 27.82 34.32 ... ... 34.56 22.89 28.28 ... 34.81 28.51 23.32 34.93 ... 35.05 28.74 ... 23.75 28.97 ... 23.97 29.20 ... 24.18 29.43 ... ... 24.39 29.54 ... 29.66 24.61 ... ... 24.82 ... ... 24.93 25.03 ... ... ... ... ... ... 1.05

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. * This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-58

ENGINEERING/TECHNICAL PAGES PT11- 4


315014M

336014M

350014M

385014M

432614M

457814M

495614M

532014M

574014M

616014M

686014M

1.05 45.42 29.95 35.00 41.32 --25.01 41.57 30.41 35.48 25.35 41.82 35.71 30.86 41.95 --42.07 35.95 25.87 31.31 36.19 26.30 31.54 36.43 --31.76 36.66 26.73 --31.99 36.78 26.94 36.90 32.22 27.16 --32.44 27.26 --32.55 32.67 27.59 ----27.80 27.79 --28.01 1.05

1.10 49.58 34.30 39.25 45.51 23.85 29.58 45.76 34.77 39.73 29.96 46.01 39.98 35.23 46.14 24.69 46.26 40.22 30.47 35.70 40.46 30.91 35.93 40.70 25.53 36.16 40.94 31.35 25.95 36.39 41.06 31.57 41.18 36.62 31.80 26.36 36.85 31.94 26.57 36.96 37.08 32.24 26.78 26.99 32.46 32.49 27.20 32.67 1.10

1.10 52.36 37.18 42.08 48.30 27.05 32.56 48.55 37.66 42.56 32.96 48.80 42.81 38.12 48.93 27.91 49.05 43.05 33.46 38.59 43.29 33.91 38.83 43.54 28.76 39.06 43.78 34.36 29.19 39.29 43.90 34.58 44.02 39.53 34.81 29.62 39.76 34.97 29.83 39.87 39.99 35.25 30.04 30.25 35.48 35.53 30.47 35.70 1.10

1.10 59.28 44.30 49.09 55.24 34.66 39.85 55.50 44.78 49.59 40.28 55.75 49.84 45.26 55.88 35.56 56.01 50.08 40.78 45.74 50.33 41.24 45.98 50.58 36.45 46.22 50.82 41.70 36.89 46.46 50.94 41.93 51.07 46.69 42.17 37.34 46.93 42.35 37.56 47.05 47.17 42.63 37.78 38.00 42.86 42.93 38.22 43.09 1.10

1.10 68.68 53.88 58.59 64.67 44.60 49.57 64.93 54.37 59.10 50.02 65.19 59.35 54.86 65.32 45.53 65.45 59.60 50.52 55.35 59.85 51.00 55.60 60.10 46.46 55.84 60.35 51.48 46.92 56.08 60.47 51.72 60.60 56.33 51.95 47.38 56.57 52.16 47.61 56.69 56.81 52.43 47.85 48.08 52.67 52.75 48.30 52.90 1.10

1.10 73.66 58.92 63.61 69.67 49.77 54.66 69.93 59.42 64.12 55.12 70.18 64.37 59.92 70.31 50.71 70.44 64.62 55.63 60.41 64.87 56.11 60.66 65.13 51.66 60.91 65.38 56.60 52.13 61.15 65.50 56.84 65.63 61.40 57.08 52.59 61.64 57.29 52.83 61.77 61.89 57.56 53.06 53.30 57.80 57.89 53.53 58.04 1.10

1.10 81.12 66.46 71.11 77.14 57.45 62.26 77.40 66.97 71.62 62.73 77.66 71.88 67.47 77.79 58.41 77.92 72.13 63.24 67.97 72.39 63.73 68.22 72.64 59.37 68.47 72.90 64.22 59.85 68.72 73.02 64.47 73.15 68.97 64.71 60.33 69.22 64.93 60.56 69.34 69.46 65.20 60.80 61.04 65.44 65.54 61.28 65.68 1.10

1.10 88.30 73.71 78.33 84.33 64.79 69.55 84.59 74.21 78.84 70.02 84.85 79.10 74.72 84.98 65.77 85.11 79.36 70.54 75.22 79.61 71.03 75.48 79.87 66.74 75.73 80.12 71.53 67.22 75.98 80.25 71.78 80.38 76.23 72.02 67.71 76.48 72.25 67.95 76.61 76.73 72.52 68.19 68.43 72.76 72.86 68.67 73.01 1.10

1.10 96.58 82.04 86.64 92.62 73.21 77.92 92.88 82.55 87.16 78.40 93.15 87.42 83.06 93.28 74.20 93.41 87.67 78.93 83.57 87.93 79.43 83.83 88.19 75.19 84.08 88.45 79.93 75.68 84.33 88.58 80.18 88.71 84.59 80.43 76.17 84.84 80.65 76.41 84.97 85.09 80.92 76.66 76.90 81.17 81.28 77.15 81.42 1.10

1.10 104.86 90.37 94.95 100.91 81.61 86.28 101.17 90.89 95.47 86.77 101.44 95.73 91.40 101.57 82.61 101.70 95.99 87.29 91.91 96.25 87.80 92.17 96.51 83.60 92.42 96.77 88.30 84.10 92.68 96.90 88.55 97.03 92.93 88.80 84.59 93.19 89.04 84.84 93.32 93.44 89.31 85.09 85.33 89.56 89.66 85.58 89.81 1.10

1.10 118.66 104.23 108.78 114.72 95.55 100.17 114.98 104.75 109.30 100.67 115.25 109.57 105.26 115.38 96.56 115.51 109.83 101.20 105.78 110.09 101.71 106.04 110.35 97.57 106.30 110.61 102.22 98.07 106.56 110.74 102.47 110.87 106.81 102.73 98.57 107.07 102.96 98.82 107.20 107.33 103.23 99.07 99.32 103.49 103.60 99.58 103.74 1.10

Center distance is greater than eight times the Small Sprocket and the Large Sprocket is not flanged. Large Sprocket should be ordered with flanges as a special. * This length correction factor must be used to determine the proper belt width.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-59

ENGINEERING/TECHNICAL PAGES PT11- 4

Sprockets

3.21 3.23 3.27 3.29 3.38 3.43 3.50 3.50 3.60 3.69 3.73 3.79 3.82 3.86 3.86 4.00 4.00 4.00 4.20 4.24 4.36 4.42 4.50 4.50 4.67 4.80 4.80 4.91 4.94 4.97 5.05 5.14 5.25 5.33 5.40 5.60 5.65 5.65 5.79 6.00 6.00 6.00 6.35 6.40 6.62 6.75 6.86

Center Distance, Inches

Conveyor Components

Speed Ratio

Sprocket Combinations Driver Driven Pitch Pitch No. of No. of Dia. Dia. teeth teeth Inches Inches Length Factor* 28 4.912 90 15.790 52 9.123 168 29.475 44 7.720 144 25.264 34 5.965 112 19.650 64 11.229 216 37.896 56 9.825 192 33.686 32 5.614 112 19.650 48 8.421 168 29.475 40 7.018 144 25.264 52 9.123 192 33.686 30 5.263 112 19.650 38 6.667 144 25.264 44 7.720 168 29.475 29 5.088 112 19.650 56 9.825 216 37.896 28 4.912 112 19.650 36 6.316 144 25.264 48 8.421 192 33.686 40 7.018 168 29.475 34 5.965 144 25.264 44 7.720 192 33.686 38 6.667 168 29.475 32 5.614 144 25.264 48 8.421 216 37.896 36 6.316 168 29.475 30 5.263 144 25.264 40 7.018 192 33.686 44 7.720 216 37.896 34 5.965 168 29.475 29 5.088 144 25.264 38 6.667 192 33.686 28 4.912 144 25.264 32 5.614 168 29.475 36 6.316 192 33.686 40 7.018 216 37.896 30 5.263 168 29.475 34 5.965 192 33.686 38 6.667 216 37.896 29 5.088 168 29.475 28 4.912 168 29.475 32 5.614 192 33.686 36 6.316 216 37.896 34 5.965 216 37.896 30 5.263 192 33.686 29 5.088 192 33.686 32 5.614 216 37.896 28 4.912 192 33.686 Length Factor*

Engineering

14MM Pitch HT200 Belt Drive Selection Table

HT Synchrous Belts

DYNA-SYNC

SELECTION


DYNA-SYNC

SELECTION 20MM Ratio/Center Distance Tables Drive Ratio

HT Synchrous Belts Sprockets Conveyor Components Engineering

1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.05 1.06 1.06 1.06 1.06 1.07 1.07 1.08 1.08 1.09 1.10 1.11 1.11 1.12 1.13 1.13 1.13 1.14 1.15 1.16 1.17 1.18 1.18 1.18 1.20 1.20 1.21 1.22 1.23 1.24 1.25 1.25 1.25 1.26 1.27 1.29

Sprocket Combination Driver Driven No. Pitch No. Pitch Th. Dia. Th. Dia. Belt Length Factor —> 34 8.522 34 8.522 36 9.023 36 9.023 38 9.524 38 9.524 40 10.026 40 10.026 44 11.028 44 11.028 48 12.031 48 12.031 52 13.033 52 13.033 56 14.036 56 14.036 60 15.038 60 15.038 64 16.041 64 16.041 68 17.043 68 17.043 72 18.046 72 18.046 80 20.051 80 20.051 90 22.557 90 22.557 38 9.524 40 10.026 36 9.023 38 9.524 34 8.522 36 9.023 68 17.043 72 18.046 64 16.041 68 17.043 60 15.038 64 16.041 56 14.036 60 15.038 52 13.033 56 14.036 48 12.031 52 13.033 44 11.028 48 12.031 40 10.026 44 11.028 36 9.023 40 10.026 72 18.046 80 20.051 34 8.522 38 9.524 64 16.041 72 18.046 80 20.051 90 22.557 60 15.038 68 17.043 56 14.036 64 16.041 52 13.033 60 15.038 38 9.524 44 11.028 48 12.031 56 14.036 34 8.522 40 10.026 68 17.043 80 20.051 44 11.028 52 13.033 40 10.026 48 12.031 60 15.038 72 18.046 56 14.036 68 17.043 36 9.023 44 11.028 52 13.033 64 16.041 90 22.557 112 28.072 48 12.031 60 15.038 64 16.041 80 20.051 72 18.046 90 22.557 38 9.524 48 12.031 44 11.028 56 14.036 56 14.036 72 18.046 Belt Length Factor —>

Nominal Center Distance

2000 0.8 26.0 25.2 24.4 23.6 22.1 20.5 18.9 17.3 ... ... ... ... ... ... 24.0 24.8 25.6 ... ... ... 16.5 18.1 19.7 21.3 22.8 24.4 ... 25.2 ... ... ... ... 17.3 23.2 18.9 24.8 ... 20.5 22.0 ... ... 23.6 ... ... 18.1 ... ... 22.4 19.6 ... 0.8

2500 0.9 35.8 35.0 34.3 33.5 31.9 30.3 28.8 27.2 25.6 24.0 22.5 20.9 ... ... 33.9 34.7 35.4 21.7 23.2 24.8 26.4 28.0 29.5 31.1 32.7 34.3 ... 35.0 22.4 ... 24.0 25.6 27.2 33.1 28.7 34.6 ... 30.3 31.9 23.2 24.8 33.5 26.3 ... 27.9 20.8 ... 32.3 29.5 23.9 0.85

3400 0.95 53.6 52.8 52.0 51.2 49.6 48.0 46.5 44.9 43.3 41.7 40.2 38.6 35.4 31.5 51.6 52.4 53.2 39.4 41.0 42.5 44.1 45.7 47.3 48.8 50.4 52.0 37.0 52.8 40.2 33.5 41.7 43.3 44.9 50.8 46.5 52.4 37.8 48.0 49.6 40.9 42.5 51.2 44.1 ... 45.7 38.5 35.0 50.0 47.2 41.7 0.95

Belt Length Code Designation 3800 4200 4600 5000 5400 1.0 1.05 61.4 69.3 77.2 85.0 92.9 60.6 68.5 76.4 84.3 92.1 59.9 67.7 75.6 83.5 91.3 59.1 66.9 74.8 82.7 90.6 57.5 65.4 73.2 81.1 89.0 55.9 63.8 71.7 79.5 87.4 54.3 62.2 70.1 78.0 85.8 52.8 60.6 68.5 76.4 84.3 51.2 59.1 66.9 74.8 82.7 49.6 57.5 65.4 73.2 81.1 48.0 55.9 63.8 71.7 79.5 46.5 54.3 62.2 70.1 78.0 43.3 51.2 59.1 66.9 74.8 39.4 47.3 55.1 63.0 70.9 59.5 67.3 75.2 83.1 91.0 60.2 68.1 76.0 83.9 91.7 61.0 68.9 76.8 84.7 92.5 47.3 55.1 63.0 70.9 78.8 48.8 56.7 64.6 72.5 80.3 50.4 58.3 66.2 74.0 81.9 52.0 59.9 67.7 75.6 83.5 53.6 61.4 69.3 77.2 85.0 55.1 63.0 70.9 78.7 86.6 56.7 64.6 72.4 80.3 88.2 58.3 66.1 74.0 81.9 89.8 59.8 67.7 75.6 83.5 91.3 44.9 52.8 60.6 68.5 76.4 60.6 68.5 76.4 84.3 92.1 48.0 55.9 63.8 71.7 79.5 41.3 49.2 57.1 65.0 72.8 49.6 57.5 65.4 73.2 81.1 51.2 59.1 66.9 74.8 82.7 52.8 60.6 68.5 76.4 84.3 58.7 66.5 74.4 82.3 90.2 54.3 62.2 70.1 78.0 85.8 60.2 68.1 76.0 83.9 91.7 45.7 53.5 61.4 69.3 77.2 55.9 63.8 71.7 79.5 87.4 57.5 65.4 73.2 81.1 89.0 48.8 56.7 64.6 72.4 80.3 50.4 58.3 66.1 74.0 81.9 59.1 66.9 74.8 82.7 90.6 52.0 59.8 67.7 75.6 83.5 34.9 42.8 50.7 58.6 66.5 53.5 61.4 69.3 77.2 85.0 46.4 54.3 62.2 70.1 77.9 42.9 50.7 58.6 66.5 74.4 57.9 65.7 73.6 81.5 89.4 55.1 63.0 70.9 78.7 86.6 49.6 57.5 65.3 73.2 81.1 1.0 1.05

5800 100.8 100.0 99.2 98.4 96.9 95.3 93.7 92.1 90.6 89.0 87.4 85.8 82.7 78.8 98.8 99.6 100.4 86.6 88.2 89.8 91.3 92.9 94.5 96.1 97.6 99.2 84.3 100.0 87.4 80.7 89.0 90.6 92.1 98.0 93.7 99.6 85.0 95.3 96.9 88.2 89.8 98.4 91.3 74.4 92.9 85.8 82.3 97.2 94.5 89.0

6200 1.1 108.7 107.9 107.1 106.3 104.7 103.2 101.6 100.0 98.4 96.9 95.3 93.7 90.6 86.6 106.7 107.5 108.3 94.5 96.1 97.6 99.2 100.8 102.4 103.9 105.5 107.1 92.1 107.9 95.3 88.6 96.9 98.4 100.0 105.9 101.6 107.5 92.9 103.2 104.7 96.1 97.6 106.3 99.2 82.3 100.8 93.7 90.1 105.1 102.4 96.8 1.1

6600 116.5 115.8 115.0 114.2 112.6 111.0 109.5 107.9 106.3 104.7 103.2 101.6 98.4 94.5 114.6 115.4 116.1 102.4 103.9 105.5 107.1 108.7 110.2 111.8 113.4 115.0 100.0 115.8 103.2 96.5 104.7 106.3 107.9 113.8 109.5 115.4 100.8 111.0 112.6 103.9 105.5 114.2 107.1 90.1 108.7 101.6 98.0 113.0 110.2 104.7

NOTES: All 20MM HTD Drives operating above 1000 RPM may require a sound dampening guard. Belt lengths of 5200, 5600, 6000, and 6400 are also available. Interpolate center distance.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-60

ENGINEERING/TECHNICAL PAGES PT11- 4


DYNA-SYNC

SELECTION 20MM Ratio/Center Distance Tables

3400 0.95 51.6 48.8 43.3 35.7 50.4 44.8 39.3 46.4 49.2 42.5 48.0 28.9 36.5 50.8 44.0 40.0 49.6 45.6 48.4 47.2 43.2 37.2 50.0 40.8 44.8 48.8 30.3 47.6 46.4 ... 37.9 44.0 49.1 31.0 47.9 41.5 46.7 45.5 38.7 31.7 48.3 47.1 45.9 44.7 ... 42.3 32.4 ... 39.4 47.5 0.95

Belt Length Code Designation 4200 4600 5000 5400 1.0 1.05 59.4 67.3 75.2 83.1 90.9 56.7 64.6 72.4 80.3 88.2 51.2 59.0 66.9 74.8 82.7 43.6 51.5 59.4 67.3 75.2 58.3 66.1 74.0 81.9 89.8 52.7 60.6 68.5 76.4 84.2 47.2 55.1 63.0 70.8 78.7 54.3 62.2 70.1 77.9 85.8 57.1 64.9 72.8 80.7 88.6 50.3 58.2 66.1 74.0 81.9 55.9 63.8 71.6 79.5 87.4 36.8 44.7 52.6 60.5 68.4 44.4 52.3 60.2 68.0 75.9 58.6 66.5 74.4 82.3 90.1 51.9 59.8 67.7 75.6 83.4 47.9 55.8 63.7 71.6 79.5 57.5 65.3 73.2 81.1 89.0 53.5 61.4 69.3 77.1 85.0 56.3 64.1 72.0 79.9 87.8 55.1 62.9 70.8 78.7 86.6 51.1 59.0 66.9 74.7 82.6 45.1 53.0 60.9 68.8 76.7 57.8 65.7 73.6 81.5 89.3 48.7 56.6 64.5 72.4 80.2 52.7 60.6 68.4 76.3 84.2 56.6 64.5 72.4 80.3 88.2 38.2 46.2 54.1 62.0 69.9 55.4 63.3 71.2 79.1 87.0 54.3 62.1 70.0 77.9 85.8 ... 36.0 44.0 51.9 59.8 45.9 53.8 61.7 69.6 77.4 51.9 59.7 67.6 75.5 83.4 57.0 64.9 72.8 80.7 88.5 39.0 46.9 54.8 62.7 70.7 55.8 63.7 71.6 79.5 87.4 49.4 57.3 65.2 73.1 81.0 54.6 62.5 70.4 78.3 86.2 53.4 61.3 69.2 77.1 85.0 46.6 54.5 62.4 70.3 78.2 39.7 47.6 55.6 63.5 71.4 56.2 64.1 72.0 79.9 87.7 55.0 62.9 70.8 78.7 86.5 53.8 61.7 69.6 77.5 85.4 52.6 60.5 68.4 76.3 84.2 ... 37.7 45.7 53.7 61.7 50.2 58.1 66.0 73.9 81.8 40.4 48.4 56.3 64.2 72.1 ... ... 38.5 46.6 54.6 47.3 55.3 63.2 71.1 79.0 55.4 63.3 71.2 79.0 86.9 1.0 1.05

3800

5800 98.8 96.1 90.5 83.0 97.6 92.1 86.6 93.7 96.4 89.7 95.3 76.3 83.8 98.0 91.3 87.4 96.8 92.9 95.6 94.5 90.5 84.6 97.2 88.1 92.1 96.0 77.8 94.8 93.7 67.8 85.3 91.3 96.4 78.5 95.2 88.9 94.0 92.9 86.1 79.3 95.6 94.4 93.2 92.0 69.6 89.7 80.0 62.6 86.8 94.8

6200 1.1 106.7 103.9 98.4 90.9 105.5 100.0 94.5 101.6 104.3 97.6 103.1 84.2 91.7 105.9 99.2 95.2 104.7 100.8 103.5 102.3 98.4 92.5 105.1 96.0 100.0 103.9 85.7 102.7 101.5 75.7 93.2 99.2 104.3 86.4 103.1 96.8 101.9 100.7 94.0 87.2 103.5 102.3 101.1 99.9 77.5 97.5 87.9 70.6 94.7 102.7 1.1

6600 114.6 111.8 106.3 98.8 113.4 107.9 102.3 109.4 112.2 105.5 111.0 92.1 99.6 113.8 107.1 103.1 112.6 108.6 111.4 110.2 106.3 100.3 113.0 103.9 107.8 111.8 93.6 110.6 109.4 83.6 101.1 107.0 112.2 94.3 111.0 104.7 109.8 108.6 101.9 95.1 111.4 110.2 109.0 107.8 85.4 105.4 95.8 78.5 102.6 110.6

NOTES: All 20MM HTD Drives operating above 1000 RPM may require a sound dampening guard. Belt lengths of 5200, 5600, 6000, and 6400 are also available. Interpolate center distance. FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-61

ENGINEERING/TECHNICAL PAGES PT11- 4

HT Synchrous Belts

2500 0.9 33.8 31.1 25.5 ... 32.6 27.1 21.5 28.7 31.5 24.7 30.3 ... ... 33.0 26.3 22.2 31.8 27.8 30.6 29.4 25.4 ... 32.2 23.0 27.0 31.0 ... 29.8 28.6 ... ... 26.1 31.4 ... 30.2 23.7 28.9 27.7 20.7 ... 30.5 29.3 28.1 26.9 ... 24.4 ... ... 21.4 29.7 0.9

Sprockets

2000 0.8 24.0 21.2 ... ... 22.8 17.2 ... 18.8 21.6 ... 20.4 ... ... 23.2 ... ... 22.0 17.9 20.7 19.5 ... ... 22.3 ... 17.0 21.1 ... 19.9 18.6 ... ... ... 21.5 ... 20.2 ... 19.0 17.8 ... ... 20.6 19.4 18.1 16.8 ... ... ... ... ... 19.7 0.8

Conveyor Components

1.29 1.30 1.31 1.32 1.33 1.33 1.33 1.36 1.37 1.38 1.40 1.40 1.41 1.41 1.42 1.43 1.44 1.45 1.47 1.50 1.50 1.50 1.53 1.54 1.55 1.56 1.56 1.58 1.60 1.60 1.61 1.64 1.65 1.65 1.67 1.67 1.68 1.70 1.73 1.75 1.76 1.78 1.79 1.80 1.80 1.82 1.87 1.87 1.88 1.88

Nominal Center Distance

Engineering

Drive Ratio

Sprocket Combination Driver Driven No. Pitch No. Pitch Th. Dia. Th. Dia. Belt Length Factor —> 34 8.522 44 11.028 40 10.026 52 13.033 52 13.033 68 17.043 68 17.043 90 22.557 36 9.023 48 12.031 48 12.031 64 16.041 60 15.038 80 20.051 44 11.028 60 15.038 38 9.524 52 13.033 52 13.033 72 18.046 40 10.026 56 14.036 80 20.051 112 28.072 64 16.041 90 22.557 34 8.522 48 12.031 48 12.031 68 17.043 56 14.036 80 20.051 36 9.023 52 13.033 44 11.028 64 16.041 38 9.524 56 14.036 40 10.026 60 15.038 48 12.031 72 18.046 60 15.038 90 22.557 34 8.522 52 13.033 52 13.033 80 20.051 44 11.028 68 17.043 36 9.023 56 14.036 72 18.046 112 28.072 38 9.524 60 15.038 40 10.026 64 16.041 90 22.557 144 36.092 56 14.036 90 22.557 44 11.028 72 18.046 34 8.522 56 14.036 68 17.043 112 28.072 36 9.023 60 15.038 48 12.031 80 20.051 38 9.524 64 16.041 40 10.026 68 17.043 52 13.033 90 22.557 64 16.041 112 2.072 34 9.023 60 15.038 36 9.023 64 16.041 38 9.524 68 17.043 40 10.026 72 18.046 80 20.051 144 36.092 44 11.028 80 20.051 60 15.038 112 28.072 90 22.557 168 42.108 48 12.031 90 22.557 34 8.522 64 16.041 Belt Length Factor —>


DYNA-SYNC

SELECTION 20MM Ratio/Center Distance Tables Drive Ratio

HT Synchrous Belts Sprockets Conveyor Components Engineering

1.89 1.89 2.00 2.00 2.00 2.00 2.00 2.05 2.10 2.11 2.12 2.12 2.13 2.15 2.22 2.25 2.25 2.33 2.33 2.35 2.37 2.40 2.40 2.40 2.47 2.50 2.55 2.57 2.63 2.65 2.67 2.70 2.77 2.80 2.80 2.82 2.95 3.00 3.00 3.00 3.00 3.11 3.18 3.20 3.23 3.27 3.29 3.38 3.43 3.50

Sprocket Combination Driver Driven No. Pitch No. Pitch Th. Dia. Th. Dia. Belt Length Factor —> 36 9.023 68 17.043 38 9.524 72 18.046 34 8.522 68 17.043 36 9.023 72 18.046 40 10.026 80 20.051 56 14.036 112 28.072 72 18.046 144 36.092 44 11.028 90 22.557 80 20.051 168 42.108 38 9.524 80 20.051 34 8.522 72 18.046 68 17.043 144 36.092 90 22.557 192 48.123 52 13.033 112 28.072 36 9.023 80 20.051 40 10.026 90 22.557 64 16.041 144 36.092 48 12.031 112 28.072 72 18.046 168 42.108 34 8.522 80 20.051 38 9.524 90 22.557 60 15.038 144 36.092 80 20.051 192 48.123 90 22.557 216 54.139 68 17.043 168 42.108 36 9.023 90 22.557 44 11.028 112 28.072 56 14.036 144 36.092 64 16.041 168 42.108 34 8.522 90 22.557 72 18.046 192 48.123 80 20.051 216 54.139 52 13.033 144 36.092 40 10.026 112 28.072 60 15.038 168 42.108 68 17.043 192 48.123 38 9.524 112 28.072 48 12.031 144 36.092 56 14.036 168 42.108 64 16.041 192 48.123 72 18.046 216 54.139 36 9.023 112 28.072 68 17.043 216 54.139 60 15.038 192 48.123 52 13.033 168 42.108 44 11.028 144 36.092 34 8.522 112 28.072 64 16.041 216 54.139 56 14.036 192 48.123 48 12.031 168 42.108 Belt Length Factor —>

Nominal Center Distance

2000 0.8 18.4 17.2 18.8 17.5 ... ... ... ... ... ... 17.8 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0.8

2500 0.9 28.4 27.2 28.8 27.6 25.1 ... ... 22.1 ... 25.4 27.9 ... ... ... 25.8 22.7 ... ... ... 26.1 23.1 ... ... ... ... 23.4 ... ... ... 23.7 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0.9

3400 0.95 46.3 45.1 46.6 45.4 43.0 33.1 ... 40.1 ... 43.4 45.8 ... ... 33.8 43.7 40.8 ... 34.5 ... 44.1 41.2 ... ... ... ... 41.5 35.1 ... ... 41.9 ... ... ... 35.8 ... ... 36.2 26.4 ... ... ... 36.5 ... ... ... 27.1 36.8 ... ... ... 0.95

Belt Length Code Designation 4200 4600 5000 5400 1.0 1.05 54.2 62.1 70.0 77.9 85.7 53.0 60.9 68.8 76.7 84.5 54.6 62.5 70.3 78.2 86.1 53.3 61.2 69.1 77.0 84.9 50.9 58.8 66.7 74.6 82.5 41.1 49.1 57.0 65.0 72.9 30.9 39.1 47.1 55.1 63.1 48.1 56.0 63.9 71.8 79.7 ... ... 40.2 48.3 56.4 51.3 59.2 67.1 75.0 82.9 53.7 61.6 69.5 77.4 85.3 31.6 39.8 47.8 55.8 63.8 ... ... ... 40.9 49.1 41.8 49.8 57.8 65.7 73.6 51.7 59.6 67.5 75.4 83.3 48.8 56.7 64.6 72.6 80.5 32.3 40.4 48.5 56.5 64.5 42.5 50.5 58.5 66.4 74.4 ... 33.2 41.5 49.7 57.7 52.0 59.9 67.9 75.8 83.7 49.2 57.1 65.0 72.9 80.8 32.9 41.1 49.2 57.3 65.2 ... ... ... 42.5 50.7 ... ... ... ... 43.1 ... 33.9 42.2 50.3 58.4 49.5 57.5 65.4 73.3 81.2 43.2 51.2 59.2 67.1 75.1 33.6 41.8 49.9 58.0 66.0 ... 34.5 42.8 51.0 59.1 49.9 57.8 65.7 73.7 81.6 ... ... 35.4 43.8 52.1 ... ... ... ... 44.8 34.2 42.5 50.6 58.7 66.7 43.9 51.9 59.9 67.9 75.8 ... 35.2 43.5 51.7 59.8 ... ... 36.1 44.5 52.8 44.3 52.3 60.3 68.2 76.2 34.9 43.1 51.3 59.3 67.4 ... 35.8 44.2 52.4 60.5 ... ... 36.7 45.1 53.4 ... ... ... ... 46.1 44.6 52.6 60.6 68.6 76.5 ... ... ... 38.1 46.7 ... ... 37.3 45.8 54.1 ... 36.5 44.8 53.1 61.2 35.6 43.8 52.0 60.0 68.1 44.9 53.0 61.0 69.0 76.9 ... ... ... 38.8 47.3 ... ... 38.0 46.4 54.8 ... 37.1 45.5 53.7 61.9 1.0 1.05

3800

5800 93.6 92.4 94.0 92.8 90.4 80.8 71.1 87.6 64.4 90.8 93.2 71.8 57.2 81.5 91.2 88.4 72.5 82.3 65.8 91.5 88.7 73.2 58.9 51.4 66.5 89.1 83.0 73.9 67.2 89.5 60.3 53.1 74.7 83.7 67.9 60.9 84.1 75.4 68.6 61.6 54.4 84.5 55.1 62.3 69.3 76.1 84.8 55.7 63.0 70.0

6200 1.1 101.5 100.3 101.9 100.7 98.3 88.7 79.0 95.5 72.3 98.7 101.1 79.7 65.2 89.4 99.1 96.2 80.4 90.2 73.8 99.4 96.6 81.2 67.0 59.6 74.5 97.0 90.9 81.9 75.2 97.4 68.3 61.3 82.6 91.7 75.9 69.0 92.0 83.3 76.6 69.7 62.7 92.4 63.3 70.4 77.3 84.1 92.8 64.0 71.1 78.0 1.1

6600 109.4 108.2 109.8 108.6 106.2 96.6 86.9 103.4 80.3 106.6 109.0 87.6 73.2 97.3 106.9 104.1 88.4 98.1 81.7 107.3 104.5 89.1 75.0 67.8 82.5 104.9 98.8 89.8 83.2 105.3 76.4 69.5 90.6 99.6 83.9 77.1 99.9 91.3 84.6 77.8 70.8 100.3 71.5 78.5 85.3 92.0 100.7 72.2 79.2 86.0

NOTES: All 20MM HTD Drives operating above 1000 RPM may require a sound dampening guard. Belt lengths of 5200, 5600, 6000, and 6400 are also available. Interpolate center distance.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-62

ENGINEERING/TECHNICAL PAGES PT11- 4


DYNA-SYNC

SELECTION 20MM Ratio/Center Distance Tables

2000 0.8 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0.8

2500 0.9 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0.9

3400 0.95 27.7 ... ... 28.0 ... ... 28.3 ... ... ... 28.7 ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0.95

Belt Length Code Designation 4200 4600 5000 5400 1.0 1.05 36.2 44.5 52.6 60.7 68.8 ... ... ... 39.4 48.0 ... ... 38.6 47.1 55.4 36.5 44.8 53.0 61.1 69.1 29.1 37.8 46.1 54.4 62.6 ... ... ... 40.0 48.6 36.9 45.1 53.3 61.4 69.5 ... ... 39.2 47.7 56.1 ... ... ... 40.7 49.3 29.7 38.4 46.8 55.1 63.2 37.2 45.5 53.7 61.8 69.8 ... ... 39.9 48.4 56.7 30.1 38.7 47.1 55.4 63.6 ... ... ... 41.3 49.9 30.4 39.0 47.5 55.7 63.9 ... 31.7 40.5 49.0 57.4 ... ... ... 41.9 50.6 30.7 39.4 47.8 56.1 64.2 ... 32.0 40.8 49.4 57.7 ... 32.3 41.1 49.7 58.0 ... ... ... 42.5 51.2 ... 32.6 41.4 50.0 58.4 ... ... 33.9 42.9 51.5 ... ... 34.2 43.2 51.8 ... ... 34.5 43.5 52.1 1.0 1.05

3800

5800 76.8 56.4 63.6 77.1 70.6 57.0 77.5 64.3 57.7 71.3 77.8 65.0 71.7 58.3 72.0 65.6 59.0 72.4 66.0 66.3 59.6 66.6 60.0 60.3 60.6

6200 1.1 84.8 64.7 71.8 85.1 78.7 65.3 85.5 72.5 66.0 79.4 85.8 73.1 79.7 66.7 80.1 73.8 67.3 80.4 74.2 74.5 68.0 74.8 68.3 68.6 69.0 1.1

6600 92.7 72.9 79.9 93.1 86.7 73.5 93.4 80.6 74.2 87.4 93.8 81.2 87.8 74.9 88.1 81.9 75.6 88.5 82.3 82.6 76.2 83.0 76.6 76.9 77.2

HT Synchrous Belts

3.60 3.60 3.69 3.79 3.82 3.86 4.00 4.00 4.15 4.20 4.24 4.36 4.42 4.50 4.67 4.80 4.91 4.94 5.05 5.33 5.40 5.65 5.68 6.00 6.35

Nominal Center Distance

Sprockets

Drive Ratio

Sprocket Combination Driver Driven No. Pitch No. Pitch Th. Dia. Th. Dia. Belt Length Factor —> 40 10.026 144 36.092 60 15.038 216 54.139 52 13.033 192 48.123 38 9.524 144 36.092 44 11.028 168 42.108 56 14.036 216 54.139 36 9.023 144 36.092 48 12.031 192 48.123 52 13.033 216 54.139 40 10.026 168 42.108 34 8.522 144 36.092 44 11.028 192 48.123 38 9.524 168 42.108 48 12.031 216 54.139 36 9.023 168 42.108 40 10.026 192 48.123 44 11.028 216 54.139 34 8.522 168 4.108 38 9.524 192 48.123 36 9.023 192 48.123 40 10.026 216 54.139 34 8.522 192 48.123 38 9.524 216 54.139 36 9.023 216 54.139 34 8.522 216 54.139 Belt Length Factor —>

Engineering

Conveyor Components

NOTES: All 20MM HTD Drives operating above 1000 RPM may require a sound dampening guard. Belt lengths of 5200, 5600, 6000, and 6400 are also available. Interpolate center distance.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS SPROC ETS PAGES PT11-4

SPECIFICATIONS BELTS PAGES PT11-1

PT11-63

ENGINEERING/TECHNICAL PAGES PT11- 4


DYNA-SYNC

ENGINEERING/TECHNICAL Overhung Load Calculations

HT Synchrous Belts

Overhung load is an important consideration for drive design. Motor and reducer bearings are rated for specific load capacities to achieve calculated life. If the drive design is such that bearing loads are exceeded, life will be proportionally reduced. Likewise, if the drive exerts a lesser load on the bearings, life will be extended. Needless to say, drive design that keeps bearing loads below ratings can pay big dividends.

Now consider the same situation for a motor or gearbox. Referring to Fig. 2, it should be obvious that the HT/HTD sprocket should be mounted as close as possible to the face of the gearbox. As the distance between the gearbox face and HT/HTD sprocket increases, the bearing load is also increased, which leads to a reduction in bearing life.

BELT PULL: The basis for overhung load calculation is belt pull. Belt pull is the result of torque being transmitted when the belt exerts a pull on the sprocket diameter. EXAMPLE: 5 horsepower at 200 RPM is 1,575 inchpounds of torque. If a 6 inch diameter sprocket is used, (3 inch radius), 1,575/3 = 525 pounds effective belt pull is required. Note that if a larger diameter sprocket is used, belt pull is reduced accordingly. Belt pull can be calculated using the following formula: Fig. 2

Sprockets

Belt Pull (lbs) =126,000 x DHP x F RPM x PD Where:

Another warning from gearbox manufacturers is that the centerline of belt pull should not extend beyond the end of the shaft. Given a choice of a small diameter, wide facewidth drive design, or a larger diameter, narrower facewidth alternative, the latter would be preferable if bearing life is an important consideration.

DHP = Design Horsepower F = Drive Factor (1.3 for sync. belt) RPM = Shaft RPM PD = Pitch Diameter of Sprocket

Conveyor Components

BEARING LOAD: Belt pull translates into bearing load and is greatly affected by the location of the sprocket on the shaft. Fig. 1 shows an example of what happens as the distance between the centerline of belt pull and the adjacent bearing is extended.

DRIVE DESIGN CONSIDERATIONS For any given application, there are usually several possible drive alternatives. In some cases, the selection with the smallest diameter sprockets might be the least expensive. As can be seen from the previous discussion, this alternative could be a bad choice. Smaller diameter sprockets lead to higher belt pull; their greater width is also more sensitive to misalignment.

Fig. 1 Engineering

a 10 in. 10 in.

b 1 in. 5 in.

FEATURES/BENEFITS PAGES PT11-2

Belt Pull 500 lbs. 500 lbs.

Bearing Load “B� 550 lbs. 750 lbs.

SPECIFICATIONS: SPROCKETS PAGES PT11-4

SPECIFICATIONS: BELTS PAGES PT11-17

PT11-64

SELECTION PAGES PT11-19


HT/HTD Drive Installation SPROCKET INSTALLATION

SPROCKET ALIGNMENT

1. Thoroughly inspect the bore of the sprocket and the tapered surface of the bushing. Any paint, dirt, oil or grease must be removed.

HT/HTD sprocket alignment and parallelism of the shafts are very important. Proper alignment helps to equalize the load across the entire belt width, thereby reducing wear and extending belt life.

4. Line up assembly so as not to misalign belts and tighten screws evenly and progressively. Apply the recommended torque to screws.

After aligning the sprockets, check the rigidity of the supporting framework. Shafts should be well supported to prevent distortion and a resulting change in the center distance under load. Do not use spring-loaded or weighted idlers. Idler sprockets or pulleys must be locked into position after adjusting belt tension. Sprockets

3. With key in keyseat of shaft, slide sprocket to its desired position with screw heads to the outside. If it is hard to slide the bushing onto the shaft, check shaft for burrs, etc.

Place a straightedge against the outside edge of the sprockets and move sprockets until the straightedge touches the two outside and two inside edges of the sprockets. The straightedge should cross the sprockets as close to the shafts as possible. A string can be used if a straightedge is not available. Remember the string should contact at four points as explained above. (See illustration on page PT11-66.

BELT INSTALLATION & TENSIONING Do not pry or otherwise force the belt onto the sprockets, as this can result in permanent damage to the belt. Reduce the center distance between the pulleys so that the belt can be easily installed. HT 200 drives must be properly tensioned. If the belt is too loose, it may jump teeth when heavier loads are applied. If the belt is too tight, belt life will suffer, and bearings will be unnecessarily overloaded. Improper tension can result in excessive drive noise. Tensioning procedure: First, measure the span length and calculate the deflection distance of 1/64, per inch span (see illustration).

Engineering

Use the formula method on page PT11-66 to calculate recommended deflection forces.

Apply a force (from the table) at the center of the span. Measure the deflection with this force applied. Move the center distance until the proper deflection is obtained.

Conveyor Components

2. Assemble bushing into sprocket. Loosely insert the screws into assembly. At least one sprocket must have flanges.

HT Synchrous Belts

DYNA-SYNC

ENGINEERING/TECHNICAL

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS: SPROCKETS PAGES PT11-4

SPECIFICATIONS: BELTS PAGES PT11-17

PT11-65

SELECTION PAGES PT11-19


DYNA-SYNC

ENGINEERING/TECHNICAL Drive Alignment

HT Synchrous Belts

Good tracking of synchronous belts on their sprockets depends upon alignment to within 1/4 degree. This translates to a maximum “M” dimension of 0.05” per foot center distance.

Drive Tensioning Formula Method

Step 3.

The formula method for determining belt tension may be used for greater accuracy, or for applications that fall out of guidelines given for the Simplified Method on page PT11-65. Sprockets

Step 1.

Table 2 Belt

Calculate Min. Installation Tension:

Formula 1: Where:

T= 20 (HP) + mV2 V

HP = Horsepower V = Belt Velocity (in FPM) 1000 m = Value in Table 2.

Conveyor Components

Belt Velocity = PD x RPM x .262 (PD = Pitch Dia. in inches)

*Important! If formula calculation for "T" is less than "Min T. Value" (Table 2) use the "Min T. Value" for T. Always use the greater T value; i.e. from T Formula 1 or Table 2. Step 2.

Calculate Deflection Forces:

Formula 2:

Min Force = 1.0T + (K/L)Y 16

(lbs)

Formula 3:

Max Force = 1.1T + (K/L)Y 16

(lbs)

Note:

Adjust tension per Simplified Method Procedure on page PT11-65 using deflection forces from Step 2.

Pitch 5MM 5MM 8MM 8MM 8MM 8MM 14MM 14MM 14MM 14MM 14MM 20MM 20MM 20MM 20MM 20MM

Factors Width 15MM 25MM 20MM 30MM 50MM 85MM 40MM 55MM 85MM 115MM 170MM 115MM 170MM 230MM 290MM 340MM

m 0.28 0.47 0.58 0.88 1.46 2.45 1.78 2.44 3.77 5.11 7.55 7.24 10.71 14.49 18.27 21.42

Y 24.9 41.5 34.2 51.3 85.5 145.3 93.0 127.9 197.7 267.5 395.4 367.0 542.5 734.0 925.4 1085.0

Min. T Value* 14.1 23.4 18.5 30.0 52.0 94.5 76.5 120.0 205.5 291.0 447.0 391.5 603.0 834.0 1065.0 1257.5

Engineering

For used belt, use 0.7T to 0.8T instead of the 1.0T and 1.1T for new belts. T = Static tension, lbs K = Span length, inches L = Belt length, inches Y = Factor from Table 2.

FEATURES/BENEFITS PAGES PT11-2

SPECIFICATIONS: SPROCKETS PAGES PT11-4

SPECIFICATIONS: BELTS PAGES PT11-17

PT11-66

SELECTION PAGES PT11-19


DYNA-SYNC

ENGINEERING/TECHNICAL DODGE Software Computer Selection of DODGE Synchronous Belt Drives

VIA-SYNC® For any given synchronous drive application, there may be several DODGE HT/HTD* or DODGE DYNA-SYNC® product combinations that could satisfy the requirements. Finding the best drive can be a time-consuming and frustrating task.

VIA-SYNC calculates speed up drives or drives for nonstandard motor speeds. The most appropriate selection can then be specified using the computer printout, which contains sprocket, bushing and belt sizes and part numbers.

The DODGE VIA-SYNC program provides selections for DYNA-SYNC (timing) and HT/HTD drives and includes both TAPER-LOCK® and QD* type sprockets. All relevant data for up to ten alternative drive selections is presented in a format that allows quick and accurate analysis, whether based upon lowest price, minimum bearing load, highest service factor, etc.

VIA-SYNC has the capability of sharing data with DODGE T-A DISCovery™ or DODGE SCD DISCovery™ programs.

HT Synchrous Belts

Synchronous Belt Drive Selection

Remedy

Unusual Noise

Misaligned drive Hi or Low belt tension Backside idler Worn sprocket Bent sprocket flange Excessive belt speed Incorrect belt profile Subminimal spkt. dia. Excessive load Weak mntg. structure

Re-adjust alignment Adjust to recommended value Use inside idler Replace sprocket Replace or repair Redesign drive Replace with DODGE belt Redesign with lager spkts. Use higher capacity drive

Weak mntg. structure Excessive spkt. wear Fixed center drive Excessive debris Excessive load Subminimal spkt. dia. Drive running hot Belt degradation

Reinforce mounting structure Use wear-resistant sprockets Install inside idler Install adequate drive guard. Use higher capacity drive Redesign drive Use heat fingers on hot shaft Protect from excessive heat

Belt Edge Wear

Damaged flanges Low belt tension Poor tracking Guard interference

Repair or replace sprocket Adjust to recommended value Correct alignment Remove obstruction, add idler

Premature Tooth Wear

Improper tension Poor alignment Wrong belt type Worn sprocket Damaged sprocket Excessive load Dirt or debris Sprocket wobble

Correct drive tension Correct drive alignment Use correct DODGE belt Replace Replace Use higher capacity drive Install adequate drive guard Correct bushing installation

Loss of Belt Tension

FEATURES/BENEFITS PAGES PT11-2

Problem

Cause

Remedy

Tooth Shear

Shock loads Few teeth in mesh Worn sprocket Backside idler Wrong belt profile Low belt tension

Use higher capacity drive Redesign drive Replace Use inside idler Use correct DODGE belt Adjust to recommended value

Tensile Break

Shock load Subminimal spkt. dia. Debris in drive Improper belt handling, storage

Use higher capacity drive Redesign with larger spkts. Install adequate drive guard Do not crimp belt or subject it to sharp bends

Belt Subminimal spkt. dia. Cracking Backside idler Start-up temp below 180 degrees F Extended exposure to harsh chemicals

Redesign with larger spkts. Install inside idler Preheat drive before start-up

Bearing Failure

Adjust to recommended value Re-adjust alignment Redesign with larger spkts.

Excessive belt tension Drive misalignment Subminimal spkt. dia.

Vibration Wrong belt profile Hi or Low belt tension Loose key or bushing Loose mounting structure Belt not Tracking

SPECIFICATIONS: SPROCKETS PAGES PT11-4

Misalignment Long center distance Mtg. structure bending

SPECIFICATIONS: BELTS PAGES PT11-17

PT11-67

Protect drive

Conveyor Components

Cause

Install correct DODGE belt Adjust to recommended value Install per instructions Reinforce or tighten Re-adjust alignment Carefully adjust alignment Reinforce mounting structure

SELECTION PAGES PT11-19

Engineering

Problem

Sprockets

DRIVE TROUBLESHOOTING


DYNA-SYNC

NOTES

HT Synchrous Belts

Sprockets

Conveyor Components

Engineering

PT11-68


C

Related Products: Tensioner Frame. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-40 Idler Sprockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-40 Chain Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-41 Engineering/Technical Custom TAPER-LOCK Sprocket Data . . . . . . . . . . . . . . . . . . . . . . . . PT12-42 Sprocket Pitch Diameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-43 Sprocket and Chain Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-44 Installation & Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-45

Sprockets

Selection: Procedure, Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-28 Basic Horsepower Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-32

Conveyor Components

Specification: TAPER-LOCK, A, B: #35 Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-3 #41 Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-5 #40 Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-6 #50 Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-9 #60 Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-12 #80 Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-15 #100 Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-18 #120 Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-19 #140 Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-21 #160 Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-22 #180 Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-24 #200 Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-24 #240 Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-25 Double-Single Sprockets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-26 Extended Pitch Sprockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-27

HT Synchrous Belts

Features/Benefits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT12-2

Part Number Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .INDEX-1 Keyword Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .INDEX-29

PT12-1

Engineering

S

DYNA-SYNC

CONTENTS


DYNA-SYNC

FEATURES/BENEFITS Sprockets for Roller Chain FEATURING TAPER-LOCK SPROCKETS . . . Shaft Ready For low-speed roller chain drives, DODGE TAPER-LOCK sprockets are the perfect solution for extra muscle.

HT Synchrous Belts

Advantages • Features Compact design Single TAPER-LOCK Sprocket

• Installs easily • Fits shaft securely

Double Strand TAPER-LOCK Sprocket

• Comes in wide range of stock sizes • Allows exact ratio/rating required for your operation • Installation-ready, right from the box • Meets ANSI standards • B-reborable and A-plate sprockets available

HARDENED TOOTH SPROCKETS LIKE THIS

Hardened Teeth at No Extra Cost

Double-Single TAPER-LOCK Sprocket

Sprockets

Other Sprocket Types from Dodge

• Through 25 teeth • #40 through #160 • No price premium With Hardened Tooth Sprockets

Advantages

AVOID SPROCKET WEAR LIKE THIS

• Offers twice the wear life • Saves downtime and replacement costs • Equalizes wear between large and small sprocket

A-plate Sprockets

• Offers greater resistance against abrasive wear Conveyor Components

Without Hardened Tooth Sprockets

• Extends chain life

B-reborable Sprockets

Simple Mounting Easy On

Easy Off

• Insert bushing into sprocket.

• Take both screws out entirely.

• Match holes (not threads).

• Insert one screw into hole that is threaded in the bushing only.

• Put screws into holes that are farthest apart.

• Use as jackscrew to disengage bushing.

• Slip unit onto shaft. • Set drive alignment and tighten screws. Engineering

PT12-2


35 for 3/8” Pitch Single Strand Chain

TYPE A

TYPE B

FEATURES/BENEFITS PAGE PT12-2

SELECTION PAGES PT12-2

1

.88

1/2

1-1/4

1.0

1/2

1-11/16

1.0

PLATE–TYPE A C Descr. Part Stock Wt. Hub Dia. No. No. Bore ...... .... ..... ..... .75 .84◊ .79◊ ...... .... ..... ..... .75 1.06◊ ...... .... ..... ..... .75 1.22◊ ...... .... ..... ..... .75 1.25◊ ...... .... ..... ..... .75 1.25 ...... .... ..... ..... .75 1.38 .1 35A15 103001 1/2 .75 1.47 .1 35A16 103002 1/2 .75 1.63 .2 35A17 103003 1/2 .75 .2 1/2 .75 1.75 35A18 103004 .2 1/2 .75 1.88 35A19 103005 .2 1/2 .75 1.94 35A20 103006 .2 1/2 .75 2.13 35A21 103007 .2 1/2 .75 2.13 35A22 103008 .3 1/2 .75 2.13 35A23 103009 .3 1/2 .88 2.13 35A24 103010 .3 1/2 .88 2.13 35A25 103011 .4 1/2 1 2.25 35A26 103012 .4 1/2 1 2.25 35A28 103013 .5 1/2 1 2.25 35A30 103014 .5 1/2 1 2.25 35A32 103015 .7 1/2 1 2.25 35A35 103255 .7 1/2 1 2.25 35A36 103016 .9 5/8 1 2.25 35A40 103017 1.0 5/8 1 2.25 35A42 103018 1.1 5/8 1 2.25 35A45 103019 1.2 5/8 1 2.25 35A48 103020 1.5 5/8 1 2.25 35A54 103021 1.9 3/4 1 2.25 35A60 103022 2.5 3/4 1 2.25 35A70 103260 103023 2.7 3/4 1 2.25 35A72 3.3 3/4 1 2.25 35A80 103263 3.7 3/4 1 2.25 35A84 103024 4.7 3/4 1 2.25 35A96 103264 6.6 3/4 1 2.25 35A112 103025 See List Price Book MLP for alteration charges.

ENGINEERING/TECHNICAL PAGES PT12-42

HT Synchrous Belts

1/2

B

RELATE PRO UCTS PAGES PT12-40

PT12-3

B

Sprockets

REBORABLE SPROCKETS–TYPE B Bore No. Spkt. Part Descr. Wt. Teeth O.D. No. Stock Max. 9 105320 .1 1.256 3/8 35B9 3/8 10 .1 1.379 3/8 35B10 105300 9/16 11 .1 1.502 3/8 35B11 105301 5/8 12 .2 1.625 1/2 35B12 105302 3/4 13 .2 1.746 1/2 35B13 105303 3/4 14 .3 1.868 1/2 35B14 105304 3/4 15 .3 1.989 1/2 35B15 105305 13/16 16 .4 2.110 1/2 35B16 105306 7/8 17 .4 2.231 1/2 35B17 105307 1 .5 1/2 1-1/16 18 2.352 35B18 105001 .6 1/2 1-3/16 19 2.472 35B19 105002 .7 1/2 1-3/16 20 2.593 35B20 105003 .8 1/2 1-1/4 21 2.713 35B21 105004 .8 1/2 1-1/4 22 2.833 35B22 105005 .9 1/2 1-1/4 23 2.954 35B23 105321 .9 1/2 1-1/4 24 3.074 35B24 105006 .9 1/2 1-1/4 25 3.194 35B25 105322 .9 1/2 26 1-1/2 3.314 35B26 105007 1.0 1/2 28 1-1/2 3.553 35B28 105323 1.1 1/2 30 1-1/2 3.793 35B30 105008 1.1 1/2 32 1-1/2 4.032 35B32 105009 1.6 1/2 35 1-1/2 4.392 35B35 105010 1.7 1/2 36 1-1/2 4.511 35B36 105324 1.8 5/8 40 1-1/2 4.990 35B40 105011 1.9 5/8 42 1-1/2 5.229 35B42 105325 2.0 5/8 45 1-1/2 5.588 35B45 105012 2.1 5/8 48 1-1/2 5.946 35B48 105013 2.4 5/8 54 1-1/2 6.663 35B54 105326 2.8 3/4 60 1-1/2 7.380 35B60 105327 3.7 3/4 70 1-1/2 8.575 35B70 105328 3.9 105329 3/4 72 1-1/2 8.814 35B72 4.5 3/4 80 1-1/2 9.770 35B80 105330 4.9 3/4 84 1-1/2 10.247 35B84 105331 6.0 3/4 96 1-1/2 11.680 35B96 105332 6.6 3/4 112 1-1/2 13.590 35B112 105333 ◊ Hub grooved for chain clearance.

Bore Range Min. Max.

Conveyor Components

TYPE BTL

TAPER-LOCK SPROCKETS Wt. C No. Spkt. Description Part No. w/o Bush. Hub Dia. Teeth O.D. 18 100350 .5 2.352 1.88◊ 35BTL18-1008 1.81 19 100351 .6 2.472 35BTL19-1008 1.94 20 100352 .7 2.593 35BTL20-1008 2.06 21 100353 .8 2.713 35BTL21-1008 100354 .9 22 2.38◊ 2.833 35BTL22-1210 2.50◊ 100343 1.0 23 2.954 35BTL23-1210 2.44 100355 1.0 24 3.074 35BTL24-1210 2.44 100344 1.3 25 3.194 35BTL25-1210 100356 1.3 26 2.88◊ 3.314 35BTL26-1610 2.88 100345 1.3 28 3.553 35BTL28-1610 3.13 100357 1.4 30 3.793 35BTL30-1610 3.25 100358 1.5 32 4.032 35BTL32-1610 3.25 100359 1.6 35 4.392 35BTL35-1610 3.25 100346 1.6 36 4.511 35BTL36-1610 100360 2.1 40 3.25 4.990 35BTL40-1610 100347 2.2 42 3.25 5.229 35BTL42-1610 100361 2.3 45 3.25 5.588 35BTL45-1610 100362 2.5 48 3.25 5.946 35BTL48-1610 100363 2.8 54 3.25 6.663 35BTL54-1610 100364 3.2 60 3.25 7.380 35BTL60-1610 100365 3.3 3.25 70 8.575 35BTL70-1610 100348 4.1 3.25 72 8.814 35BTL72-1610 100366 4.2 3.25 80 9.770 35BTL80-1610 100349 5.1 3.25 84 10.247 35BTL84-1610 100367 6.2 3.25 96 11.680 35BTL96-1610 8.0 3.25 112 13.590 35BTL112-1610 100368 ◊ Hub grooved for chain clearance.

Engineering

No.

DYNA-SYNC

SPECIFICATION


DYNA-SYNC

SPECIFICATION No.

35-2 for 3/8” Pitch Double Strand Chain .561"

HT Synchrous Belts

C

B TYPE BTL

TAPER-LOCK–DOUBLE Wt. No. Spkt. Description Part w/o Teeth O.D. + No. Bush. D35BTL19H-1008 2.472 19 101150 .6 D35BTL20H-1008 2.593 20 101151 .8 D35BTL21H-1008 2.713 21 101152 1.4 D35BTL22H-1008 2.833 22 101153 1.7 D35BTL24H-1210 3.074 24 101154 1.8 D35BTL26-1210 3.314 26 101155 2.0 D35BTL30-1610 3.793 30 101156 1.8 D35BTL32-1610 4.032 32 101157 2.0 D35BTL35-1610 4.392 35 101158 2.3 D35BTL40-1610 4.990 40 101159 2.9 D35BTL45-1610 5.588 45 101160 3.2 D35BTL48-1610 5.946 48 101161 3.5 D35BTL54-1610 6.663 54 101162 3.9 D35BTL70-1610 8.575 70 101164 6.3 D35BTL80-1610 9.770 80 7.9 101165 96 11.680 D35BTL96-1610 101166 9.9 112 13.590 D35BTL112-1610 101167 10.9 + “H” suffix indicates Hardened Teeth.

Sprockets

No. Teeth

.561

C Conveyor Components

B TYPE B

Spkt. O.D.

Bore Range Min. Max. 1 1/2 1 1/2 1 1/2 1 1/2 1-1/4 1/2 1-1/4 1/2 1-11/16 1/2 1-11/16 1/2 1-11/16 1/2 1-11/16 1/2 1-11/16 1/2 1-11/16 1/2 1-11/16 1/2 1-11/16 1/2 1-11/16 1/2 1/2 1-11/16 1/2 1-11/16

REBORABLE SPROCKETS–TYPE B Bore Part Wt. No. Stock Max.

Description +

D35B12H 1.630 12 D35B13H 1.750 13 D35B14H 1.870 14 D35B15H 1.990 15 D35B16H 2.110 16 D35B17H 2.230 17 D35B18H 2.350 18 D35B19H 2.470 19 D35B20H 2.590 20 D35B21H 2.710 21 D35B22H 2.830 22 D35B23H 2.950 23 D35B24H 3.070 24 D35B25H 3.190 25 D35B26 3.310 26 D35B30 3.790 30 D35B36 4.510 36 D35B42 5.230 42 D35B48 5.950 48 D35B52 6.430 52 D35B60 7.380 60 D35B68 8.340 68 D35B72 8.810 72 D35B76 9.290 76 D35B84 10.250 84 D35B95 11.560 95 D35B96 11.680 96 D35B102 12.400 102 + “H” suffix indicates Hardened Teeth.

105525 105526 105527 105181 105182 105183 105184 105528 105529 105530 105531 105532 105533 105534 105535 105536 105537 105538 105539 105540 105541 105542 105543 105544 105545 105546 105547 105548

.32 .36 .44 .56 .64 .74 .84 .96 1.08 1.24 1.42 1.54 1.62 1.66 1.98 2.34 3.00 3.80 4.66 5.40 6.84 10.01 11.04 11.94 14.98 17.42 18.14 19.92

B 0.88 0.88 0.88 0.88 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00

C Hub Dia. 1.81 1.88 1.81 1.81 2.47 2.47 3.06 3.25 3.25 3.25 3.25 3.25 3.25 3.25 3.25 3.25 3.25

C Hub Dia. 0.98 1.25 9/16 1/2 1.13 1.25 3/4 1/2 1.25 1.25 13/16 1/2 1.41 1.25 7/8 1/2 1.47 1.25 15/16 1/2 1.59 1.25 1-1/16 1/2 1.72 1.25 1-1/8 1/2 1.84 1.25 1-1/4 1/2 1.97 1.38 1-5/16 1/2 2.06 1.38 1-5/8 1/2 2.19 1.38 1-7/16 1/2 2.31 1.38 1-1/2 1/2 2.44 1.38 1-5/8 1/2 2.56 1.38 1-11/16 1/2 2.69 1.38 3/4 1/2 3.16 1.38 2 1/2 2.50 1.38 1-3/4 11/16 2.50 1.38 1-3/4 11/16 2.50 1.38 1-3/4 11/16 2.50 1.38 1-3/4 11/16 2.50 1.38 1-3/4 11/16 3.50 1.50 2-3/8 15/16 3.50 1.50 2-3/8 15/16 3.50 1.50 2-3/8 15/16 3.50 1.50 2-3/8 15/16 3.50 1.50 2-3/8 15/16 3.50 1.50 2-3/8 15/16 3.50 1.50 2-3/8 1 See List Price Book MLP for alteration charges. B

Engineering FEATURES/BENEFITS PAGE PT12-2

SELECTION PAGES PT12-2

RELATE PRO UCTS PAGES PT12-40

PT12-4

ENGINEERING/TECHNICAL PAGES PT12-42


41 for 1/2” Pitch Single Strand Chain

TYPE A

FEATURES/BENEFITS PAGE PT12-2

Spkt. O.D.

100387 100388 100389 100395 100390 100391

REBORABLE SPROCKETS–TYPE B Wt. Bore Part Descr. No. Stock Max.

105297 9 1.674 41B9 10 1.839 41B10 105308 11 2.003 41B11 105309 12 2.166 41B12 105310 13 2.328 41B13 105311 14 2.490 41B14 105014 15 2.652 41B15 105015 16 2.814 41B16 105016 17 2.974 41B17 105017 18 3.136 41B18 105018 19 3.292 41B19 105019 20 3.457 41B20 105020 21 3.618 41B21 105021 22 3.778 41B22 105022 23 3.938 41B23 105334 24 4.098 41B24 105023 25 4.258 41B25 105335 26 4.418 41B26 105024 28 4.738 41B28 105337 30 5.057 41B30 105025 32 5.376 41B32 105026 35 5.586 41B35 105027 36 6.015 41B36 105338 40 6.653 41B40 105339 45 7.450 41B45 105340 48 7.928 41B48 105341 54 8.884 41B54 105342 60 9.840 41B60 105343 72 11.752 80 13.026 96 15.573 ◊ Hub grooved for chain clearance.

.2 .2 .3 .4 .5 .6 .7 .8 .9 1.0 1.3 1.5 1.5 1.8 2.1 2.2 2.3 2.5 2.7 2.7 2.9 3.5 3.5 4.1 4.3 4.7 5.2 6.5

1/2 1/2 1/2 1/2 1/2 1/2 1/2 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 3/4 3/4 3/4 3/4 3/4

SELECTION PAGES PT12-2

5/8 3/4 7/8 1 1 1 1-5/16 1-3/8 1-1/2 1-5/8 1-3/4 1-7/8 1-7/8 1-3/4 1-3/4 1-3/4 1-3/4 1-3/4 1-3/4 1-3/4 1-3/4 1-3/4 1-3/4 2 2 2 2 2

B

Min.

Max.

1/2

1

.88

1/2

1-1/4

1.0

1/2

1-11/16

1.0

1/2

1-11/16

1.0

5.1 5.9 7.6 8.4 9.8 11.3

PLATE–TYPE A B 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.13 1.13 1.13 1.13 1.13

C Hub. Dia. 1.13◊ 1.25◊ 1.47◊ 1.56◊ 1.56◊ 1.75 1.91 2.06 2.23 2.38 2.47 2.75 2.88 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 3.00 3.00 3.00 3.00 3.00

Spkt. No.

Part No.

Wt.

Stock Bore

.28 1/2 41A15 103026 .34 1/2 41A16 103027 .36 1/2 41A17 103028 .44 5/8 41A18 103029 .46 5/8 41A19 103030 .52 5/8 41A20 103031 .60 5/8 41A21 103032 .66 5/8 41A22 103033 .72 5/8 41A23 103034 .82 5/8 41A24 103035 .88 5/8 41A25 103036 .94 5/8 41A26 103037 1.08 5/8 41A28 103038 1.20 5/8 41A30 103039 1.44 3/4 41A32 103040 1.70 3/4 41A35 103268 1.84 3/4 41A36 103041 2.22 3/4 41A40 103042 2.92 3/4 41A45 103043 2.50 3/4 41A48 103044 3.54 3/4 41A54 103045 4.60 3/4 41A60 103046 6.7 1 41A72 103047 8.1 1 41A80 103245 11.7 1 41A96 103246 See List Price Book MLP for alteration charges.

RELATE PRO UCTS PAGES PT12-40

PT12-5

Bore Range

HT Synchrous Belts

14 2.490 41BTL14-1008 15 2.652 41BTL15-1008 16 2.814 41BTL16-1008 17 2.974 41BTL17-1210 18 3.136 41BTL18-1210 19 3.292 41BTL19-1210 20 3.457 41BTL20-1610 21 3.618 41BTL21-1610 22 3.778 41BTL22-1610 23 3.938 41BTL23-1610 24 4.098 41BTL24-1610 25 4.258 41BTL25-1610 26 4.418 41BTL26-1610 28 4.738 41BTL28-1610 30 5.057 41BTL30-1610 32 5.376 41BTL32-1610 35 5.856 41BTL35-1610 36 6.015 41BTL36-1610 40 6.653 41BTL40-1610 45 7.450 41BTL45-1610 48 7.928 41BTL48-1610 54 8.725 41BTL54-1610 60 9.840 41BTL60-1610 70 11.433 41BTL70-1610 72 11.752 41BTL72-1610 80 13.026 41BTL80-1610 96 15.573 41BTL96-1610 ◊ Hub grooved for chain clearance.

No. Teeth

TYPE B

Description

Sprockets

TYPE BTL

Spkt. O.D.

ENGINEERING/TECHNICAL PAGES PT12-42

Conveyor Components

No. Teeth

TAPER-LOCK SPROCKETS Wt. C Part w/o Hub No. Bush. Dia. 100369 .5 1.87◊ 1.00 100370 .6 2.00 100371 .7 100372 .8 2.38◊ 2.38◊ 100373 1.0 2.50 100374 1.2 100375 1.3 2.88◊ 3.00◊ 100376 1.4 3.00 1.5 100377 3.00 100392 1.6 3.25 100378 1.6 3.25 100393 1.7 3.25 100379 1.7 100380 1.9 100381 2.0 100382 2.1 100383 2.5 100394 2.6 100384 2.9 100385 3.7 3.25 100386 4.3

Engineering

No.

DYNA-SYNC

SPECIFICATION


DYNA-SYNC

SPECIFICATION No.

40 for 1/2” Pitch Single Strand Chain No. Teeth

HT Synchrous Belts Sprockets

TYPE BTL

Spkt. O.D.

Description +

Conveyor Components

40BTL14H-1008 2.490 14 40BTL15H-1008 2.652 15 40BTL16H-1008 2.814 16 40BTL17H-1210 2.974 17 40BTL18H-1210 3.136 18 40BTL19H-1210 3.292 19 40BTL20H-1610 3.457 20 40BTL21H-1610 3.618 21 40BTL22H-1610 3.778 22 40BTL23H-1610 3.938 23 40BTL24H-1610 4.098 24 40BTL25H-1610 4.258 25 40BTL26-1610 4.418 26 40BTL27-1610 4.578 27 40BTL28-1610 4.738 28 40BTL29-1610 4.898 29 40BTL30-1610 5.057 30 40BTL32-1610 5.376 32 40BTL33-1610 5.536 33 40BTL34-1610 5.696 34 40BTL35-1610 5.856 35 40BTL36-1610 6.015 36 40BTL37-1610 6.174 37 40BTL38-1610 6.334 38 40BTL40-1610 6.653 40 40BTL41-1610 6.812 41 40BTL42-1610 6.972 42 40BTL44-1610 7.291 44 40BTL45-1610 7.450 45 40BTL47-1610 7.769 47 40BTL47-2012 7.769 47 40BTL48-1610 7.928 48 40BTL50-1610 8.248 50 40BTL54-1610 8.725 54 40BTL60-1610 9.840 60 40BTL70-2012 11.433 70 40BTL72-2012 11.752 72 40BTL80-2012 13.026 80 40BTL84-2012 13.663 84 40BTL96-2012 15.573 96 112 18.121 40BTL112-2517 ◊ Hub grooved for chain clearance. + “H” suffix indicates Hardened Teeth.

TAPER-LOCK SPROCKETS C Wt. Part Hub w/o No. Dia. Bush. 1.81◊ 100500 .4 100501 .4 1.81 100502 .5 1.94 2.38◊ 100503 .5 100504 .7 2.47◊ 100505 .8 2.47 2.78◊ 100506 .8 100507 .8 2.78◊ 100508 .8 2.78 100509 1.2 3.00 100510 1.5 3.25 100511 1.6 3.25 3.25 100512 1.5 3.25 104700 1.5 3.00 100513 1.5 3.00 104701 1.6 3.00 100514 1.7 3.00 100515 2.0 3.00 104702 2.1 3.00 104703 2.3 3.00 100516 2.4 3.00 100517 2.4 3.00 2.5 104704 3.00 2.6 104705 3.00 2.8 100518 3.00 2.9 104706 3.00 100519 3.0 3.00 104707 3.2 3.00 3.8 100520 3.00 3.8 104708 3.56 3.8 100450 3.00 3.9 100521 3.00 104709 4.5 3.00 5.0 100522 3.00 6.1 100523 3.56 100524 8.6 3.56 100525 8.7 3.56 100526 10.9 3.56 100527 11.8 3.56 100528 13.7 100529 21.3 4.25

Bore Range

B

Min.

Max.

1/2

1

0.88

1/2

1-1/4

1.00

1/2

1-11/16

1.00

1/2

1-11/16

1.00

1/2

1-11/16

1.00

1/2

1-11/16

1.00

1/2

1-11/16 2-1/8 1-11/16 1-11/16 1-11/16 1-11/16

1.00 1.25 1.00 1.00 1.00 1.00

1/2

2-1/8

1.25

1/2

2-11/16

1.75

Engineering FEATURES/BENEFITS PAGE PT12-2

SELECTION PAGES PT12-2

RELATE PRO UCTS PAGES PT12-40

PT12-6

ENGINEERING/TECHNICAL PAGES PT12-42


.88 .88 .88 .88 .88 .88 .88 .88 .88 .88 .88 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.13 1.13 1.13 1.13 1.13 1.13 1.13 1.13 1.13 1.13 1.13

4.00

B

Descr.

Part No.

Wt.

Stock Bore

.... .... .... 40A12 40A13 40A14 40A15 40A16 40A17 40A18 40A19 40A20 40A21 40A22 40A23 40A24 40A25 40A26 40A28 40A30 40A32 40A34 40A35 40A36 40A38 40A40 40A42 40A45 40A48 40A50 40A54 40A60 40A70 40A72 40A80 40A84 40A96 40A112

...... ...... ...... ...... .... .. ...... 103048 103049 103050 103051 103052 103053 103054 103055 103056 103057 103058 103059 103060 103061 103062 103063 103064 103065 103066 103067 103068 103069 103070 103071 103072 103073 103075 103076 103077 103078 103277 103247

.... .... .... .2 .2 .3 .4 .4 .5 .5 .6 .6 .7 .7 .9 .9 1.0 1.1 1.1 1.3 1.5 1.7 1.7 1.8 2.2 2.3 2.5 2.9 3.3 3.9 4.2 5.2 7.5 8.0 9.8 11.0 14.0 19.5

.. .. .. 1/2 1/2 1/2 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 1 1 1 1 1 1

TYPE A

HT Synchrous Belts

PLATE–TYPE A C Hub Dia. 1.13◊ 1.25◊ 1.47◊ 1.56◊ 1.56 1.69 1.81 2.00 2.13 2.31 2.50 2.63 2.75 2.88 2.88 3.00 3.25 3.25 3.25 3.25 3.25 3.25 3.25 3.25 3.25 3.50 3.50 3.50 3.50 3.50 3.50 3.50 4.00 4.00

Sprockets

TYPE B

REBORABLE SPROCKETS–TYPE B Bore No. Part Spkt. Wt. Descr. of No. O.D. Stock Max. Teeth 40B9 105312 5/8 1.674 1/2 9 .2 3/4 1.839 40B10 105313 1/2 10 .2 7/8 2.003 40B11 105314 1/2 11 .4 1 2.166 40B12 105315 1/2 12 .4 1 2.328 40B13 105316 1/2 13 .5 1 2.490 40B14 105028 1/2 14 .6 1-3/16 2.652 40B15 105029 1/2 15 .7 2.814 40B16 105030 1-1/4 16 5/8 .8 2.974 40B17 105031 1-5/16 17 5/8 .9 3.136 40B18 105032 1.0 1-1/2 18 5/8 3.292 40B19 105033 1.2 1-3/4 19 5/8 3.457 40B20 105034 1.5 1-3/4 20 5/8 3.618 40B21 105035 1.8 1-3/4 21 5/8 3.778 40B22 105036 1.7 1-3/4 22 5/8 3.938 40B23 105299 1.8 23 1-3/4 5/8 4.098 40B24 105037 1.9 24 1-3/4 5/8 4.258 40B25 105346 1.9 25 1-3/4 5/8 4.418 40B26 105038 2.0 26 1-3/4 5/8 4.738 40B28 105039 2.2 28 1-3/4 5/8 5.057 40B30 105040 2.4 1-3/4 30 5/8 5.376 40B32 105041 2.5 1-3/4 32 3/4 5.696 40B34 105347 3.3 34 1-3/4 3/4 5.856 40B35 105042 2.9 35 1-3/4 3/4 6.015 40B36 105043 3.0 36 1-3/4 3/4 6.334 40B38 105348 3.6 38 2 3/4 6.653 40B40 105044 3.8 2 40 3/4 6.972 40B42 105045 4.0 2 42 3/4 7.450 40B45 105046 4.4 2 45 3/4 7.928 40B48 105047 4.8 2 48 3/4 8.248 40B50 105349 5.2 2 50 3/4 8.884 40B54 105048 5.8 54 2 3/4 9.840 40B60 105049 6.8 60 2 3/4 11.433 40B70 105351 10.7 70 2 1 11.752 40B72 105050 9.6 72 2 1 13.026 80 13.663 40B84 105051 13.4 84 2 1 15.573 96 18.121 112 ◊ Hub grooved for chain clearance.

Conveyor Components

40 for 1/2” Pitch Single Strand Chain

Engineering

No.

DYNA-SYNC

SPECIFICATION

FEATURES/BENEFITS PAGE PT12-2

SELECTION PAGES PT12-2

RELATE PRO UCTS PAGES PT12-40

PT12-7

ENGINEERING/TECHNICAL PAGES PT12-42


DYNA-SYNC

SPECIFICATION No.

40-2 for 1/2” Pitch Double Strand Chain

.841"

HT Synchrous Belts

C

B

TYPE BTL 2

TYPE BTL 1

Sprockets

TYPE CTL

TAPER-LOCK SPROCKETS C Wt. No. Spkt. Description Part Hub w/o Teeth O.D. + No. Dia. Bush. 15 2.652 D40BTL15H-1008• 101001 .5 1.81 16 2.814 D40BTL16H-1008 101002 .7 1.27 17 2.974 D40BTL17H-1008 101003 .8 1.27 18 3.136 D40BTL18H-1210 101004 .7 2.29 19 3.292 D40BTL19H-1210 101005 .9 2.47 20 3.457 D40BTL20H-1610 101006 1.1 3.25 101007 1.1 2.69 21 3.618 D40BTL21H-1610 23 3.938 D40BTL23H-1610• 101008 1.4 3.00 24 4.098 D40BTL24H-1610• 104822 1.6 3.25 25 4.258 D40BTL25H-2012 101009 1.8 3.42 26 4.418 D40BTL26-2012• 104823 2.3 3.56 30 5.057 D40BTL30-2012• 101010 3.6 3.56 32 5.376 D40BTL32-2012• 104825 4.2 3.56 35 5.856 D40BTL35-2012• 104826 5.1 3.56 36 6.015 D40BTL36-2012• 101011 5.9 3.56 40 6.653 D40BTL40-2517• 104827 6.9 42 6.972 D40CTL42-2517 101012 7.4 45 7.450 D40BTL45-2517• 104828 8.5 48 7.928 D40BTL48-2517• 101013 9.4 52 8.566 D40BTL52-2517 101014 11.5 54 8.884 D40BTL54-2517• 104829 12.7 60 9.840 D40BTL60-2517• 101015 15.5 4.25 68 11.115 D40BTL68-2517• 101016 20.5 70 11.433 D40BTL70-2517• 104830 22.1 76 12.389 D40BTL76-2517• 101017 26.5 84 13.663 D40BTL84-2517• 101018 32.0 95 15.414 D40BTL95-2517• 101019 36.0 96 15.573 D40BTL96-2517• 104833 38.0 102 16.528 D40BTL102-2517• 101020 44.0 + “H” suffix indicates Hardened Teeth. • BTL2

Conveyor Components

.841 No. Teeth

C

B

Spkt. O.D.

Bore Range Min. Max. 1/2

1

0.88

1/2

1-1/4

1.00

1/2

1-11/16

1.00

1/2

2-1/8

1.25

1/2

2-11/16

1.75

REBORABLE SPROCKETS-TYPE B Bore Part Wt. No. Stock Max.

Description +

13 2.328 D40B13H 15 2.652 D40B15H 16 2.814 D40B16H 17 2.974 D40B17H 18 3.136 D40B18H 19 3.292 D40B19H 20 3.457 D40B20H 21 3.618 D40B21H 23 3.938 D40B23H + “H” suffix indicates Hardened Teeth.

105931 105185 105186 105187 105188 105189 105190 105191 105192

0.8 1.2 1.4 1.6 1.8 2.1 2.4 2.8 3.5

1/2 1/2 5/8 5/8 5/8 5/8 5/8 5/8 5/8

B

1 1-1/4 1-3/8 1-7/16 1-1/2 1-5/8 3/4 1-7/8 2

B 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.63 1.63

C Hub Dia. 1.50 1.81 1.97 2.16 2.31 2.47 2.63 2.78 3.09

TYPE B Engineering FEATURES/BENEFITS PAGE PT12-2

SELECTION PAGES PT12-2

RELATE PRO UCTS PAGES PT12-40

PT12-8

ENGINEERING/TECHNICAL PAGES PT12-42


50 for 5/8” Pitch Single Strand Chain

TYPE BTL 1

Spkt. O.D. 5.723 5.922 6.321 7.319 7.519 9.114 9.313 9.911

Bore Range Max.

1/2

1

0.88

1/2

1-1/4

1.00

1/2

1-11/16

1.00

1/2

2-1/8

1.25

1/2

2-11/16

1.75

TAPER-LOCK SPROCKETS–LARGE BORE SERIES Bore Range Hub Dia. Part Wt. C No. Min. Max. 2-11/16 1/2 4.25 3.5 100451 50BTL27L-2517 2-11/16 1/2 4.25 3.7 100452 50BTL28L-2517 2-11/16 1/2 4.25 3.9 100453 50BTL30L-2517 2-11/16 1/2 4.25 4.7 100454 50BTL35L-2517 2-11/16 1/2 4.25 5.2 100455 50BTL36L-2517 2-11/16 1/2 4.25 6.9 100456 50BTL44L-2517 2-11/16 1/2 4.25 7.0 100699 50BTL45L-2517 2-11/16 1/2 4.25 7.9 100457 50BTL48L-2517

B

Description

SELECTION PAGES PT12-2

RELATE PRO UCTS PAGES PT12-40

PT12-9

HT Synchrous Belts

B

Min.

Sprockets

Description

50BTL12H-1008 2.708 12 50BTL13H-1008 2.991 13 50BTL14H-1008 3.113 14 15 3.315 50BTL15H-1210 50BTL16H-1610 3.517 16 50BTL17H-1610 3.713 17 50BTL18H-1610 3.919 18 50BTL19H-1610 4.121 19 50BTL20H-1610 4.321 20 50BTL21H-1610 4.522 21 50BTL22H-1610 4.722 22 50BTL23H-2012 4.923 23 50BTL24H-2012 5.123 24 50BTL25H-2012 5.323 25 50BTL26-2012 5.523 26 50BTL27-2012 5.723 27 50BTL28-2012 5.922 28 50BTL29-2012 6.122 29 50BTL30-2012 6.321 30 50BTL31-2012 6.521 31 50BTL32-2012 6.721 32 50BTL33-2012 6.921 33 50BTL34-2012 7.120 34 50BTL35-2012 7.319 35 50BTL36-2012 7.519 36 50BTL37-2012 7.718 37 50BTL38-2012 9.918 38 50BTL39H-2012 8.117 39 50BTL40-2012 8.316 40 50BTL41-2012 8.516 41 50BTL42-2012 8.715 42 50BTL44-2012 9.114 44 50BTL45-2012 9.313 45 50BTL47-2012 9.711 47 50BTL48-2012 9.911 48 50BTL50-2012 10.309 50 50BTL54-2012 11.106 54 50BTL56-2012 11.504 56 50BTL60-2012 12.301 60 50BTL70-2517 14.292 70 50BTL72-2517 14.690 72 50BTL80-2517 16.283 80 50BTL84-2517 17.079 84 96 19.467 50BTL96-2517 112 22.651 50BTL112-2517 ◊ Hub grooved for chain clearance.

No. Teeth 27 28 30 35 36 44 45 48

FEATURES/BENEFITS PAGE PT12-2

Spkt. O.D.

Conveyor Components

No. Teeth

TAPER-LOCK SPROCKETS C Wt. Part Hub w/o No. Dia. Bush. 1.81◊ 100530 .5 100531 .5 1.81 100532 .6 1.81 100533 .6 2.47◊ 2.78◊ 100534 .8 100535 1.1 2.78◊ 100536 1.2 2.84 100537 1.3 3.03 3.25 100538 1.4 3.25 100539 1.5 3.25 100540 1.6 100541 2.2 100542 2.4 3.56 2.4 100543 2.5 100544 100675 2.8 100545 3.0 104712 3.1 3.2 100546 3.4 104713 3.5 100547 3.7 104714 3.9 104715 4.2 100548 4.7 100549 4.8 104716 5.1 104717 5.3 104718 5.5 100550 5.7 104719 6.0 100551 6.3 104720 6.5 100552 7.1 104721 7.4 100553 7.8 104722 8.7 100554 9.3 104723 10.5 100555 15.5 100556 16.5 100557 4.25 19.0 100558 23.1 100559 100560 32.5 100561 42.2

1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75

ENGINEERING/TECHNICAL PAGES PT12-42

Engineering

No.

DYNA-SYNC

SPECIFICATION


DYNA-SYNC

SPECIFICATION No.

50 for 5/8” Pitch Single Strand Chain No. Teeth

HT Synchrous Belts

TYPE A

Sprockets Conveyor Components

TYPE B

Spkt. O.D.

Descr.

REBORABLE-TYPE B Bore Part Wt. No. Stock Max.

9 2.093 50B9 105317 10 2.299 50B10 105318 11 2.504 50B11 105319 12 2.708 50B12 105052 13 2.911 50B13 105053 14 3.113 50B14 105054 15 3.315 50B15 105055 16 3.517 50B16 105056 17 3.718 50B17 105057 18 3.919 50B18 105058 19 4.121 50B19 105059 20 4.321 50B20 105060 21 4.522 50B21 105061 22 4.722 50B22 105062 23 4.923 50B23 105063 24 5.123 50B24 105064 25 5.323 50B25 105065 26 5.523 50B26 105066 27 5.723 50B27 105352 28 5.922 50B28 105067 30 6.321 50B30 105068 32 6.721 50B32 105069 35 7.319 50B35 105070 36 7.519 50B36 105071 40 8.316 50B40 105072 42 8.715 50B42 105073 45 9.313 50B45 105074 48 9.911 50B48 105075 50 10.309 50B50 105353 54 11.106 50B54 105076 60 12.301 50B60 105077 70 14.292 50B70 105354 72 14.690 50B72 105078 80 84 17.080 50B84 105254 96 19.470 50B96 105255 112 22.650 50B112 105219 ◊ Hub grooved for chain clearance.

.4 .5 .6 .8 .9 1.2 1.4 1.7 1.9 2.2 2.4 2.9 2.8 2.9 3.0 3.2 3.3 3.5 3.6 3.7 4.1 4.4 5.0 5.1 6.1 6.5 7.2 9.0 9.4 10.7 12.8 15.0 18.3 25.5 33.0 42.0

5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 1 1 1 1 1 1 1 1 1

3/4 7/8 31/32 1-1/4 1-1/4 1-1/4 1-1/2 1-9/16 1-7/8 1-7/8 2 2 2 2 2 2 2 2 2 2 2 2-1/8 2-1/8 2-1/8 2-1/8 2-1/4 2-1/8 2-1/8 2-1/8 2-1/8 2-1/8 2-1/8 2-1/8 2-3/4 2-3/4 2-3/4

PLATE-TYPE A B 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.13 1.13 1.13 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.63 1.63 1.63

C Hub Dia. 1.38◊ 1.56◊ 1.75◊ 2.0◊ 2.0◊ 2.13 2.63 2.50 2.69 2.88 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.25 3.25 3.25 3.25 3.25 3.25 3.25 3.25 3.25 3.25 3.25 3.25 4.0 4.0 4.0

Descr.

Part No.

Wt.

Stock Bore

.... .... .... 50A12 50A13 50A14 50A15 50A16 50A17 50A18 50A19 50A20 50A21 50A22 50A23 50A24 50A25 50A26 50A27 50A28 50A30 50A32 50A35 50A36 50A40 50A42 50A45 50A48 50A50 50A54 50A60 50A70 50A72 50A80 50A84 50A96 50A112

...... ...... ...... ...... ...... 103079 103080 103081 103082 103083 108084 103085 103086 103087 108098 103089 103090 103091 103092 103093 103094 103095 103096 103097 103088 103099 103100 103101 103102 103103 103104 103280 103105 103106 103283 103248 103249

.... .... .... .4 .5 .6 .7 .8 .8 .9 1.1 1.2 1.2 1.3 1.4 1.6 1.7 1.9 2.0 2.1 2.5 2.8 3.4 3.5 4.4 4.8 5.5 6.3 7.5 8 10 13 16 20 20 26 36

.... .... .... 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 1 1 1 1 1 1 1 1 1 1

Engineering FEATURES/BENEFITS PAGE PT12-2

SELECTION PAGES PT12-2

RELATE PRO UCTS PAGES PT12-40

PT12-10

ENGINEERING/TECHNICAL PAGES PT12-42


50-2 for 5/8” Pitch Double Strand Chain

C

B

TYPE BTL

14 3.113 D50ATL14H-1008 15 3.315 D50ATL15H-1210 16 3.517 D50ATL16H-1210 17 3.718 D50ATL17H-1610 18 3.919 D50ATL18H-1610 19 4.121 D50ATL19H-1610 20 4.321 D50BTL20H-2012 21 4.522 D50BTL21H-2012 22 4.722 D50BTL22H-2012 23 4.923 D50BTL23H-2012 24 5.123 D50BTL24H-2012 25 5.323 D50BTL25H-2012 26 5.523 D50BTL26-2012 28 5.922 D50BTL28-2012 30 6.321 D50BTL30-2517 32 6.721 D50BTL32-2517 35 7.319 D50BTL35-2517 36 7.519 D50BTL36-2517 40 8.316 D50BTL40-2517 42 8.715 D50BTL42-2517 45 9.313 D50BTL45-2517 48 9.911 D50BTL48-2517 52 10.708 D50BTL52-2517 54 11.106 D50BTL54-2517 60 12.301 D50BTL60-2517 68 13.894 D50BTL68-2517 70 14.292 D50BTL70-2517 72 14.329 D50BTL72-2517 76 15.486 D50BTL76-2517 80 16.283 D50BTL80-2517 84 17.079 D50BTL84-2517 95 19.268 D50CTL95-2517 102 20.661 D50CTL102-2517 + “H” suffix indicates Hardened Teeth.

Part No. 101031 101032 101033 101034 101035 101036 101037 101038 104834 104835 104836 101039 104837 104838 101040 104839 104840 101041 104841 101042 104842 101043 101044 104843 101045 101046 104844 104845 101047 104846 101048 101049 101050

Bore Range

C Hub Dia. .... .... .... .... .... ....

Wt. w/o Bush. .9 1.0 1.1 1.1 1.4 1.7 1.9 2.0 2.5 3.0 3.5 4.0 4.7 6.3 7.8 8.4 9.2 10.0 12.7 14.2 16.1 18.7 22.5 25.2 36.5 39.5 42.7 45.0 49.5 51.0 52 70 75

B

Min.

Max.

1/2

1.0

.88

1/2

1-1/4

1.0

1/2

1-11/16

1.0

3.56

1/2

1-11/16

1.25

4.25

1/2

2-11/16

1.75

REBORABLE–TYPE B

TYPE CTL

.1.045

C

B

No. Spkt. Description of O.D. + Teeth 13 2.911 D50B13H 14 3.113 D50B14H 15 3.315 D50B15H 16 3.567 D50B16H 17 3.718 D50B17H 18 3.919 D50B18H 19 4.121 D50B19H 20 4.321 D50B20H 21 4.522 D50B21H 26 5.523 D50B26 + “H” suffix indicates Hardened Teeth.

Bore

Part No.

Wt.

105932 105193 105194 105195 105196 105197 105198 105199 105200 105222

1.5 1.8 2.0 2.4 2.9 3.3 3.7 4.4 4.8 7.5

Stock

Max.

5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 3/4 15/16

1-5/16 1-3/8 1-1/2 1-5/8 1-7/8 1-15/16 2-1/8 2.25 2-3/8 2-1/2

B 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.88

C Hub Dia. 1.88 2.09 2.28 2.50 2.69 2.88 3.09 3.28 3.50 3.75

TYPE B

FEATURES/BENEFITS PAGE PT12-2

SELECTION PAGES PT12-2

RELATE PRO UCTS PAGES PT12-40

PT12-11

ENGINEERING/TECHNICAL PAGES PT12-42

HT Synchrous Belts

1.045"

Description +

Sprockets

TYPE ATL

Spkt. O.D.

Conveyor Components

No. Teeth

Engineering

No.

DYNA-SYNC

SPECIFICATION


DYNA-SYNC

SPECIFICATION No.

60 for 3/4” Pitch Single Strand Chain No. of Teeth

Spkt. O.D.

Description +

Part No.

Spkt. Wt. w/o Bush.

C Spkt. Hub Dia.

100562 100563 100564◊ 100565 100566◊ 100567 100568 100569 100570 100571 100572 100573 100574 100575 100576 100577 100676 100578 104725 100579 104726 100580 104727 104728 100581 100582 104729 104730 104731 100583 104732 100584 100585 104733 100586 104734 100587 104735 100588 100589 100590 100591 100592

.6 .7 1.1 1.2 1.4 1.9 2.0 2.2 2.4 2.5 2.9 3.0 3.2 3.2 3.8 4.1 4.2 4.2 4.9 5.5 5.8 6.0 6.3 6.8 7.0 7.0 7.5 8.0 8.3 8.7 9.2 9.7 10.7 12.8 13.5 15.4 17.8 19.5 20.7 30.0 31.6 34.7 44.7

1.81 1.81 2.47 2.47 2.94 2.94 3.25 3.25 3.25

1/2

1

.88

1/2

1-1/4

1.0

1/2

1-11/16

1.0

3.56

1/2

2-1/8

1.25

4.25

1/2

2-11/16

1.75

Bore Range Min. Max. 2-11/16 1/2 2-11/16 1/2 2-11/16 1/2 2-11/16 1/2 2-11/16 1/2 2-11/16 1/2 2-11/16 1/2 2-11/16 1/2

B Dim. 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75

TAPER-LOCK SPROCKETS-Large Bore Series Hub Dia. No. Spkt. Description Part Wt. C Teeth O.D. L No. 4.25 3.4 100696 60BTL21HL-2517 5.426 21 4.25 4.8 100458 60BTL27L-2517 6.867 27 4.25 4.8 100459 60BTL28L-2517 7.106 28 4.25 5.9 100460 60BTL30L-2517 7.756 30 4.25 7.5 100461 60BTL35L-2517 8.783 35 4.25 7.5 100462 60BTL36L-2517 9.023 36 4.25 8.8 104598 60BTL39L-2517 9.740 39 4.25 9.2 100463 60BTL40L-2517 9.980 40 + “H” suffix indicates Hardened Teeth.

HT Synchrous Belts Engineering

Max.

Conveyor Components

Min. 11 3.005 60BTL11H-1008 12 3.249 60BTL12H-1008 13 3.493 60BTL13H-1210 14 3.736 60BTL14H-1210 60BTL15H-1610 3.978 15 60BTL16H-1610 4.220 16 60BTL17H-1610 4.462 17 60BTL18H-1610 4.703 18 60BTL19H-1610 4.945 19 60BTL20H-2012 5.186 20 60BTL21H-2012 5.426 21 60BTL22H-2012 5.666 22 60BTL23H-2012 5.907 23 60BTL24H-2012 6.147 24 60BTL25H-2012 6.387 25 60BTL26-2012 6.627 26 60BTL27H-2012 6.867 27 60BTL28-2012 7.106 28 60BTL29H-2012 7.346 29 60BTL30-2012 7.586 30 60BTL31-2012 7.826 31 60BTL32H-2012 8.065 32 60BTL33H-2012 8.305 33 60BTL34-2012 8.544 34 60BTL35-2012 8.783 35 60BTL36H-2012 9.023 36 60BTL37-2012 9.262 37 60BTL38-2012 9.501 38 60BTL39-2012 9.740 39 60BTL40H-2012 9.980 40 60BTL41-2012 10.219 41 60BTL42-2012 10.458 42 60BTL45-2012 11.176 45 60BTL47-2012 11.654 47 60BTL48-2012 11.893 48 60BTL50-2517 12.371 50 60BTL54-2517 13.327 54 60BTL56-2517 13.805 56 60BTL60-2517 14.761 60 60BTL70-2517 17.150 70 60BTL72-2517 17.628 72 60BTL80-2517 19.539 80 60BTL84-2517 20.495 84 ◊ Hub grooved for chain clearance. + “H” suffix indicates Hardened Teeth.

Sprockets

TYPE BTL

FEATURES/BENEFITS PAGE PT12-2

SELECTION PAGES PT12-2

RELATE PRO UCTS PAGES PT12-40

PT12-12

B Lgth. Thru Bore

Bore Range

ENGINEERING/TECHNICAL PAGES PT12-42


TYPE B

TYPE A

Spkt. O.D.

Part No.

Wt.

Stock

Max.

B

C Hub Dia.

Spkt. No.

Part No.

Wt.

Stock Bore

9

2.511

60B9

105079

.6

3/4

1

1.25

1.69◊

....

......

....

....

10

2.759

60B10

105080

.8

3/4

1-3/16

1.25

1.94◊

....

......

....

....

11

3.005

60B11

105081

1.0

3/4

1-5/16

1.25

2.06◊

....

......

....

....

12

3.249

60B12

105082

1.3

3/4

1-3/8

1.25

2.38◊

....

......

....

....

13

3.493

60B13

105083

1.7

3/4

1-1/2

1.25

2.41

60A13

103107

1.0

3/4

14

3.736

60B14

105084

2.0

3/4

1-3/4

1.25

2.56

60A14

103108

1.2

3/4 3/4

15

3.978

60B15

105085

2.4

3/4

1-7/8

1.25

2.88

60A15

103109

1.3

16

4.220

60B16

105086

2.9

3/4

2

1.25

3.06

60A16

103110

1.5

3/4

17

4.462

60B17

105087

3.1

3/4

2-1/4

1.25

3.25

60A17

103111

1.7

3/4

18

4.703

60B18

105088

3.4

3/4

2-3/8

1.25

3.50

60A18

103112

1.8

3/4

19

4.945

60B19

105089

3.6

3/4

2-3/8

1.25

3.50

60A19

103113

2.0

3/4

20

5.186

60B20

105090

5.0

3/4

2-3/8

1.25

3.88

60A20

103114

2.2

3/4

21

5.426

60B21

105091

5.2

3/4

2-3/4

1.25

4.0

60A21

103115

2.5

1

22

5.666

60B22

105092

5.4

3/4

2-3/4

1.25

4.0

60A22

103116

2.8

1

23

5.907

60B23

105093

5.6

1

2-3/4

1.50

4.0

60A23

103117

3.1

1

24

6.147

60B24

105094

6.0

1

2-3/4

1.50

4.0

60A24

103118

3.3

1

25

6.387

60B25

105095

6.2

1

2-3/4

1.50

4.0

60A25

103119

3.6

1

26

6.627

60B26

105096

6.4

1

2-3/4

1.25

4.0

60A26

103120

3.9

1

27

6.867

60B27

105356

6.7

1

2-3/4

1.50

4.0

60A27

103121

4.2

1

28

7.106

60B28

105097

7.0

1

2-3/4

1.50

4.0

60A28

103122

4.6

1

30

7.586

60B30

105098

7.6

1

2-3/4

1.50

4.0

60A30

103123

5.3

1

32

8.065

60B32

105099

8.4

1

2-3/4

1.50

4.0

60A32

103124

5.9

1

34

8.540

60B34

105655

8.8

1

2-3/4

1.50

4.0

60A34

103293

7.0

1

35

8.783

60B35

105100

10

1

2-3/4

1.50

4.0

60A35

103125

7.2

1

36

9.023

60B36

105101

11

1

2-3/4

1.50

4.0

60A36

103126

7.6

1

40

9.980

60B40

105102

12

1

2-3/4

1.50

4.0

60A40

103127

9.4

1

42

10.458

60B42

105357

14

1

2-3/4

1.50

4.0

60A42

103128

10

1

45

11.176

60B45

105103

15

1

2-3/4

1.50

4.0

60A45

103129

12

1

48

11.893

60B48

105104

16

1

2-3/4

1.50

4.0

60A48

103130

14

1

54

13.327

60B54

105105

20

1-3/8

2-3/4

1.75

4.25

60A54

103131

17

1-3/8

60

14.761

60B60

105106

24

1-3/8

2-3/4

1.75

4.25

60A60

103132

20

1-3/8

70

17.150

60B70

105358

33

1-3/8

2-3/4

1.75

4.25

60A70

103133

25

1-3/8

72

17.628

60B72

105107

33

1-3/8

2-3/4

1.75

4.25

60A72

103286

28

1-3/8

80

19.539

60B80

105359

43

1-3/8

2-3/4

1.75

4.25

60A80

103134

34

1-3/8

84

20.518

60A84

103289

38

1-3/8

HT Synchrous Belts

No. Teeth

PLATE-TYPE A

Bore

Sprockets

REBORABLE SPROCKETS-TYPE B Descri ption +

Conveyor Components

60 for 3/4” Pitch Single Strand Chain

◊ Hub grooved for chain clearance. + “H” suffix indicates Hardened Teeth.

Engineering

No.

DYNA-SYNC

SPECIFICATION

FEATURES/BENEFITS PAGE PT12-2

SELECTION PAGES PT12-2

RELATE PRO UCTS PAGES PT12-40

PT12-13

ENGINEERING/TECHNICAL PAGES PT12-42


DYNA-SYNC

SPECIFICATION No.

60-2 for 3/4” Pitch Double Strand Chain 1.341

HT Synchrous Belts

TYPE ATL

Sprockets

TYPE BTL 1 1.341

C

TAPER-LOCK - DOUBLE STRAND C Wt. No. Spkt. Description Part Hub w/o Teeth O.D. + No. Dia. Bush. 2.46 1.4 101061 D60BTL13H-1215• 3.493 13 2.49 1.7 101062 D60BTL14H-1215• 3.736 14 2.74 1.7 101086 D60BTL14H-1615• 3.736 14T 2.47 1.8 101063 D60BTL15H-1615• 3.978 15 2.97 2.4 101064 D60BTL16H-1615• 4.220 16 3.25 2.6 101065 D60BTL17H-1615 4.462 17 18 4.703 D60ATL18H-2012 101066 2.8 ... 19 4.945 D60ATL19H-2012 101067 3.1 ... 3.95 3.3 101068 D60BTL20H-2517• 5.186 20 4.06 4.3 101069 D60BTL21H-2517• 5.426 21 4.25 5.5 104848 D60BTL22H-2517 5.666 22 4.25 6.1 104849 D60BTL23H-2517 5.907 23 7.2 104850 D60BTL24H-2517 6.147 24 8.0 101070 D60BTL25H-2517 6.387 25 10.2 104914 D60BTL26-2517 6.627 26 10.8 101083 D60BTL27-2517 6.867 27 11.9 104851 D60BTL28-2517 7.106 28 12.7 101084 D60BTL29-2517 7.346 29 13.4 101071 D60BTL30-2517 7.586 30 104852 15 D60BTL32-2517 8.065 32 104853 17 D60BTL35-2517 8.783 35 4.25 101072 18 D60BTL36-2517 9.023 36 23 104854 D60BTL40-2517 9.980 40 26 101073 D60BTL42-2517 10.458 42 30 101074 D60BTL45-2517 11.176 45 36 104855 D60BTL48-2517 11.893 48 41 101075 D60CTL52-2517 12.849 52 33 101076 D60BTL60-2517 14.761 60 37 101077 D60CTL68-2517 16.673 68 77 104857 D60BTL70-3020 17.150 70 83 5.25 104858 D60BTL72-3020 17.628 72 42 101078 D60BTL76-3020 18.584 76 + “H” suffix indicates Hardened Teeth. • BTL1

Bore Range Min. Max. 1-1/4 1/2 1-1/4 1-11/16

B

1.50

1/2

1-11/16

1.50

1/2

2-1/8

1.25

1/2

2-11/16

1.75

1/2

2-11/16

1.75

7/8

3-1/4

2.0

Conveyor Components

REBORABLE-TYPE B No. Teeth

B TYPE BTL 2

1.341

C

Spkt. O.D.

Description +

13 3.493 D60B13H 14 3.736 D60B14H D60B15H 3.978 15 D60B16H 4.220 16 D60B17H 4.462 17 18 4.703 D60B18H 19 4.945 D60B19H 20 5.186 D60B20H 21 5.426 D60B21H + “H” suffix indicates Hardened Teeth.

Bore

Part No.

Wt.

105201 105202 105203 105204 105205 105206 105207 105208 105209

2.6 3.2 3.8 4.5 5.3 6.5 7.2 7.7 9.0

Stock

Max

3/4 3/4 3/4 3/4 3/4 1 1 1 1

1-1/2 1-3/4 1-7/8 2 2-1/4 2-3/8 2-1/2 2-1/2 2-3/4

B 2.13 2.13 2.13 2.13 2.13 2.13 2.13 2.13 2.13

C Hub Dia. 2.25 2.50 2.75 3.00 3.22 3.44 3.69 3.75 4.13

Engineering

B

TYPE B

FEATURES/BENEFITS PAGE PT12-2

SELECTION PAGES PT12-2

RELATE PRO UCTS PAGES PT12-40

PT12-14

ENGINEERING/TECHNICAL PAGES PT12-42


80 for 1” Pitch Single Strand Chain

10 3.678 80BTL10H-1215 11 4.006 80BTL11H-1215 12 4.332 80BTL12H-1615 13 4.657 80BTL13H-1615 14 4.981 80BTL14H-1615 15 5.304 80BTL15H-1615 16 5.627 80BTL16H-2012 17 5.949 80BTL17H-2012 18 6.271 80BTL18H-2012 19 6.593 80BTL19H-2012 20 6.914 80BTL20H-2517 21 7.235 80BTL21H-2517 22 7.555 80BTL22H-2517 23 7.876 80BTL23H-2517 24 8.196 808TL24H-2517 25 8.516 80BTL25H-2517 26 8.836 80BTL26H-2517 27 9.156 80BTL27-2517 28 9.475 80BTL28-2517 29 9.795 80BTL29-2517 30 10.114 80BTL30-2517 31 10.434 80BTL31-2517 32 10.753 80BTL32-2517 33 11.073 80BTL33-2517 34 11.392 80BTL34-2517 35 80BTL35-2517 11.711 36 12.030 80BTL36-2517 37 12.349 80BTL37-2517 38 12.668 80BTL38-2517 39 12.987 80BTL39-2517 40 13.306 80BTL40-2517 41 13.625 80BTL41-2517 42 13.944 80BTL42-2517 44 14.582 80BTL44-2517 45 14.901 80BTL45-2517 48 15.857 80BTL48-2517 50 16.495 80BTL50-2517 54 17.769 80BTL54-2517 60 19.681 80BTL60-2517 70 22.867 80BTL70-3020 80 26.052 80BTL80-3020 ◊ Hub grooved for chain clearance. + “H” suffix indicates Hardened Teeth.

C Hub Dia.

Bore Range

B

Min.

Max.

1/2

1-1/4

1.50

1/2

1-11/16

1.50

3.56

1/2

2-1/8

1.25

4.25

1/2

2-11/16

1.75

5.25

7/8

3-1/4

2.00

2.38◊ 2.38◊ 2.94◊ 2.94 3.25 3.25

TAPER-LOCK SPROCKETS–Large Bore Series Bore Range Wt. C Hub No. Spkt. Description Part w/o Dia. Teeth O.D. + No. Min. Max. Bush. 21 7.235 80BTL21HL-3020 100695 6.8 5.25 7/8 3-1/4 36 12.030 80BTL36L-3020 100698 17.0 5.25 7/8 3-1/4 + “H” suffix indicates Hardened Teeth.

FEATURES/BENEFITS PAGE PT12-2

SELECTION PAGES PT12-2

RELATE PRO UCTS PAGES PT12-40

PT12-15

HT Synchrous Belts

Description +

Sprockets

TYPE BTL

Spkt. O.D.

B 2.0 2.0

ENGINEERING/TECHNICAL PAGES PT12-42

Conveyor Components

No. Teeth

TAPER-LOCK Spkt. Wt. Part w/o No. Bush. 100593 1.2 100594 1.5 100595 1.5 100596 2.5 100597 2.9 100598 3.0 100599 3.0 100600 3.5 100601 4.0 100602 4.5 100603 5.5 100604 6.1 100605 6.7 100606 7.2 100607 7.5 100608 8.5 100609 8.5 100678 9.8 100679 10.7 104738 11.5 100610 12.3 104739 12.8 100611 13.4 104740 14.1 104741 14.7 100612 15.6 100613 16.3 104742 17.2 104743 18.3 104744 19.4 100614 20.5 104745 22.2 104746 25.1 104747 28.4 100615 29.3 100616 34.6 104748 36.8 100617 39.0 100618 51.3 100619 65.8 100620 77.3

Engineering

No.

DYNA-SYNC

SPECIFICATION


DYNA-SYNC

SPECIFICATION No.

80 for 1” Pitch Single Strand Chain No. Teeth

HT Synchrous Belts

TYPE B

.575

Sprockets

TYPE A

Spkt. O.D.

REBORABLE SPROCKETS–TYPE B Bore Description Part Wt. + No. Stock Max.

Conveyor Components

9 3.348 80B9 105360 10 3.678 80B10 105361 11 4.006 80B11 105108 12 4.332 80B12 105109 13 4.657 80B13 105110 14 4.981 80B14 105111 15 5.304 80B15 105112 16 5.627 80B16 105113 17 5.949 80B17 105114 18 6.271 80B18 105115 19 6.593 80B19 105116 20 6.914 80B20 105117 21 7.235 80B21 105118 22 7.555 80B22 105119 23 7.876 80B23 105120 24 8.196 80B24 105121 25 8.516 80B25 105122 26 8.836 80B26 105123 27 9.156 80B27 105362 28 9.475 80B28 105363 30 10.114 80B30 105124 32 10.753 80B32 105125 35 11.711 80B35 105364 36 12.030 80B36 105126 40 13.306 80B40 105127 45 14.901 80B45 105128 48 15.857 80B48 105129 50 16.495 80B50 105365 54 17.769 80B54 105130 60 19.681 80B60 105131 70 22.867 80C70 105656 80 26.052 80C80 105657 ◊ Hub grooved for chain clearance. + “H” suffix indicates Hardened Teeth.

1.8 1.9 2.3 2.4 3.5 4.3 5.0 5.8 6.3 7.9 8.3 9.2 9.6 10 11 11 12 13 15 15 15 17 19 20 24 33 36 39 44 52 76 90

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8

1-3/8 1-1/2 1-5/8 1-7/8 2 2-1/4 2-3/8 2-7/16 2-7/16 2-7/16 2-7/16 2-15/16 2-15/16 2-15/16 2-15/16 2-15/16 2-15/16 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 4-1/8 4-1/8

PLATE–TYPE A C Stock Spkt. Part Wt. B Hub Bore No. No. Dia. 1.56 2.28◊ .... ...... .... .... 1.56 2.56◊ .... ...... .... .... 1.56 2.81◊ .... ...... .... .... 1.56 3.13◊ 80A12 103135 1.9 1 1.56 3.03 80A13 103136 2.2 1 1.56 3.25 80A14 103137 2.5 1 1.56 3.67 80A15 103138 2.7 1 1.63 3.75 80A16 103139 3.0 1 1.63 3.75 80A17 103140 3.5 1 1.63 3.75 80A18 103141 3.9 1 1.63 3.75 80A19 103142 4.3 1 1.63 4.50 80A20 103143 4.8 1 1.63 4.50 80A21 103144 5.2 1 1.63 4.50 80A22 103145 5.8 1 1.63 4.50 80A23 103146 6.3 1 1.63 4.50 80A24 103147 7.0 1 1.88 4.50 80A25 103148 7.6 1 1.88 4.75 80A26 103149 8.7 1-3/8 1.88 4.75 80A27 103150 9.3 1-3/8 1.88 4.75 80A28 103151 10 1-3/8 1.88 4.75 80A30 103152 12 1-3/8 1.88 4.75 80A32 103153 13 1-3/8 1.88 4.75 80A35 103154 16 1-3/8 1.88 4.75 80A36 103155 17 1-3/8 1.88 4.75 80A40 103156 21 1-3/16 1.88 4.75 80A45 103157 25 1-3/8 1.88 4.75 80A48 103158 28 1-3/8 1.88 4.75 80A50 103159 33 1-3/8 1.88 4.75 80A54 103160 35 1-3/8 1.88 4.75 80A60 103161 44 1-3/8 3.25 6.25 80A70 103162 57 1-3/8 3.25 6.25 80A80 103163 77 1-3/8 See List Price Book MLP for alteration charges.

TYPE C

Engineering FEATURES/BENEFITS PAGE PT12-2

SELECTION PAGES PT12-2

RELATE PRO UCTS PAGES PT12-40

PT12-16

ENGINEERING/TECHNICAL PAGES PT12-42


80-2 for 1” Pitch Double Strand Chain

TYPE BTL 1

1.708"

C

B

TYPE BTL 2

Spkt. O.D.

13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 30 32 35 36 40 42 48 54 60 68 76 95

4.657 4.981 5.304 5.627 5.949 6.271 6.593 6.914 7.235 7.555 7.876 8.196 8.516 8.836 9.156 9.475 10.114 10.753 11.711 12.030 13.306 13.944 15.857 17.769 19.681 22.230 24.778 30.828

Bore Range

B

Min.

Max.

1/2

1-11/16

1.50

1/2

2-1/8

1.25

1/2

2-11/16

1.75

7/8

3-1/4

2.00

7/8

3-1/4

2.00

7/8

3-1/4

2.00

HT Synchrous Belts

TYPE ATL

No. Teeth

TAPER-LOCK–DOUBLE STRAND Spkt. C Wt. Description Part Hub w/o + No. Dia. Bush. D80ATL13H-1615 101090 3.3 .... D80ATL14H-2012 101091 3.5 .... D80ATL15H-2012 101092 4.4 .... D80ATL16H-2517 101093 4.6 .... D80ATL17H-2517 101094 5.5 .... D80ATL18H-2517 101095 6.6 .... D80BTL19H-3020 101096 7.1 .... D80BTL20H-3020 101097 8.2 5.25 D80BTL21H-3020 101098 10.4 5.46 D80BTL22H-3020 104862 11.0 5.25 D80BTL23H-3020 104863 12.0 5.25 D80BTL24H-3020 104864 14.0 5.25 D80BTL25H-3020 101099 16.7 5.25 D80BTL26-3020 104865 21.3 5.25 D80BTL27-3020 101085 22.0 5.25 D80BTL28-3020 104866 22.5 5.25 D80BTL30-3020 101100 23 5.25 D80BTL32-3020 104867 33 D80BTL35-3020 104868 39 D80BTL36-3020 101101 40 D80BTL40-3020 104869 54 D80BTL42-3020 101102 56 D80BTL48-3020 104870 80 5.25 D80CTL54-3020 104871 51 D80CTL60-3020 101105 62 D80CTL68-3020 101106 75 D80CTL76-3020 101107 83 D80CTL95-3020 101108 100

Sprockets

No.

DYNA-SYNC

SPECIFICATION

REBORABLE SPROCKETS No. Teeth

C

Spkt. O.D.

Description +

13 4.657 D80B13H 14 4.981 D80B14H 15 5.304 D80B15H 16 5.627 D80B16H 17 5.949 D80B17H 18 6.271 D80B18H 19 6.593 D80B19H 20 6.914 D80B20H 21 7.235 D80B21H + “H” suffix indicates Hardened Teeth.

B TYPE B

Bore

Part No.

Wt.

105210 105211 105212 105213 105214 105215 105216 105217 105218

6.5 7.7 9.2 11.5 13.2 15 17 18 20

Stock

Max.

1 1 1 1 1 1 1 1 1

2 2-1/4 2-1/2 2-3/4 2-7/8 3-1/8 3-5/16 3-5/16 3-5/16

B 2.50 2.50 2.50 2.75 2.75 2.75 2.75 2.75 2.75

C Hub Dia. 3.03 3.31 3.63 4.00 4.31 4.63 4.94 5.00 5.00

Conveyor Components

1.708

Engineering

TYPE CTL

FEATURES/BENEFITS PAGE PT12-2

SELECTION PAGES PT12-2

RELATE PRO UCTS PAGES PT12-40

PT12-17

ENGINEERING/TECHNICAL PAGES PT12-42


DYNA-SYNC

SPECIFICATION No.

100 for 1-1/4” Pitch Single Strand Chain

HT Synchrous Belts

No. Teeth 11 12 13 14 15 16 17 18 19 20 21 21 22 23 24 25 26 28 30 32 35 36 40 42 45 48 54 60

TYPE BTL

Sprockets

TYPE B

Conveyor Components

TYPE C

Engineering

TYPE A

Spkt. O.D. 5.008 5.415 5.821 6.226 6.630 7.034 7.436 7.839 8.241 8.643 9.044 9.044 9.444 9.845 10.245 10.645 11.045 11.844 12.643 13.441 14.639 15.038 16.633 17.430 18.626 19.821 22.211 24.601

Description + 100BTL11H-1615 100BTL12H-1615 100BTL13H-2012 100BTL14H-2012 100BTL15H-2517 100BTL16H-2517 100BTL17H-2517 100BTL18H-2517 100BTL19H-2517 100BTL20H-2517 100BTL21H-2517 100BTL21HL-3020 100BTL22H-2517 100BTL23H-2517 100BTL24H-2517 100BTL25H-2517 100BTL26-2517 100BTL28-3020 100BTL30-3020 100BTL32-3020 100BTL35-3020 100BTL36-3020 100BTL40-3020 100BTL42-3020 100BTL45-3020 100BTL48-3020 100BTL54-3020 100BTL60-3020

TAPER-LOCK Part Wt. No. w/o Bush. 100621 2.7 100622 3.1 100623 3.0 100624 4.0 100625 5.5 100626 6.0 100627 7.0 100628 7.5 100629 9.7 100630 9.8 100631 10.6 100694 12.5 100632 11.4 104753 15.0 100633 14.3 104754 17.0 100634 16.0 100685 20.2 100635 21.5 100636 25.0 100637 30.2 100638 31.4 100639 36.6 104755 43 100640 47 100641 60 100642 77 100643 94

REBORABLE–TYPE B & C Bore Spkt. Descr. Part No. Wt. Type O.D. + No. Teeth Stock Max. 1-7/8 1 5.0 100B10 105366 4.598 B 10 2-1/4 1 5.2 100B11 105132 5.008 B 11 2-1/4 1 5.4 100B12 105133 5.415 B 12 2-3/8 1 6.6 100B13 105134 5.821 B 13 2-3/4 1-1/4 8.5 100B14 105135 6.226 B 14 3 1-1/4 9.4 100B15 105136 6.630 B 15 3 1-1/4 10 100B16 105137 7.034 B 16 3 1-1/4 11 100B17 105138 7.436 B 17 3 12 1-1/4 100B18 105139 7.839 B 18 3 13 1-1/4 100B19 105140 8.241 B 19 3 14 1-1/4 100B20 105141 8.643 B 20 3 1-1/4 16 100B21 105142 9.044 B 21 3 1-1/4 17 100B22 105143 9.444 B 22 3 1-1/4 18 100B23 105367 9.845 B 23 3 1-1/4 19 10.245 100B24 105144 B 24 1-3/8 3-5/16 21 11.045 100B26 105145 B 26 1-3/8 3-5/16 25 11.844 100B28 105368 B 28 1-3/8 3-5/16 27 12.643 100B30 105146 B 30 1-3/8 3-5/16 30 13.441 100B32 105147 B 32 1-3/8 3-5/16 34 14.639 100B35 105369 B 35 1-3/8 3-5/16 39 15.038 100B36 105148 B 36 1-3/8 3-5/16 47 16.633 100B40 105149 B 40 42 1-3/8 3-5/16 55 18.626 100B45 105371 B 45 4-1/8 1-3/8 66 19.821 100B48 105372 B 48 4-1/8 1-3/8 78 22.211 100C54 105411 C 54 4-1/8 1-3/8 90 24.601 100C60 105412 C 60 5-1/4 1-3/8 28.584 100C70 105220 125 C 70 5-1/4 1-3/8 32.565 100C80 105221 151 C 80 + “H” suffix indicates Hardened Teeth.

FEATURES/BENEFITS PAGE PT12-2

SELECTION PAGES PT12-2

Bore Range Min. Max.

B

1/2

1-11/16

1.50

3.56

1/2

2-1/8

1.25

4.25 4.25 4.25

1/2

2-11/16

1.75

4.25

1/2

2-11/16

1.75

5.25 4.25 4.25

7/8 1/2 1/2

3-1/4 2-11/16 2-11/16

2.0 1.75 1.75

4.50

1/2

2-11/16

1.75

5.25

7/8

3-1/4

2.0

PLATE–TYPE A Stock C Hub Spkt. Part Wt. Bore Dia. No. No. .... .... ...... ...... 3.25 1.88 1 3.4 100A11 103164 3.56 1.88 1 4.1 100A12 103165 4.00 1.88 1 4.7 100A13 103166 3.78 1.63 1-1/4 5.4 100A14 103167 4.19 1.63 1-1/4 6.2 100A15 103168 4.50 1.75 1-1/4 7.0 100A16 103169 4.50 1.75 1-1/4 7.8 100A17 103170 4.50 1.75 1-1/4 8.7 100A18 103171 4.50 1.75 1-1/4 9.6 100A19 103172 4.50 2.0 1-1/4 100A20 103173 10.6 4.50 2.0 1-1/4 100A21 103174 11.7 4.50 2.0 1-1/4 100A22 103175 12.7 4.50 2.0 1-1/4 13 100A23 103176 4.50 2.0 1-1/4 14 100A24 103177 4.50 2.0 1-3/8 17 100A26 103178 2.0 5.0 1-3/8 19 100A28 103179 2.0 5.0 1-3/8 22 100A30 103180 2.0 5.0 1-3/8 26 100A32 103181 5.0 2.0 1-3/8 30 100A35 103182 5.0 2.0 1-3/8 33 100A36 103183 5.0 2.50 1-3/8 40 100A40 103184 5.0 2.50 1-3/8 44 100A42 103185 1-3/8 50 100A45 103186 5.0 2.50 1-3/8 57 100A48 103187 6.25 2.75 1-3/8 71 100A54 103188 6.25 3.25 1-3/8 88 100A60 103189 6.25 3.75 1-3/8 118 100A70 103190 7.0 3.75 1-3/8 157 100A80 103191 7.0 3.75 See List Price Book MLP for alteration charges. B

RELATE PRO UCTS PAGES PT12-40

PT12-18

C. Hub Dia. 3.00 3.25

ENGINEERING/TECHNICAL PAGES PT12-42


100-2 for 1-1/4” Pitch Double Strand Chain REBORABLE–TYPE B & C C Hub Dia. 2.31 2.87 1-1/2 1 4.6 D100B9 101245 4.180 B 9 2.69 2.87 1-3/4 1 6.2 4.600 D100B10 101246 B 10 3.13 2.87 2-1/8 1 7.9 5.010 D100B11 101247 B 11 3.38 2.87 2-1/4 1-1/8 9.3 5.420 D100B12 101248 B 12 3.75 2.87 2-1/2 1-1/8 11.4 5.820 D100B13 101249 B 13 4.19 2.87 2-3/4 1-1/8 13.6 6.230 D100B14 101250 B 14 4.56 3.13 3-1/8 1-1/4 17.1 6.630 D100B15 101251 B 15 5.00 3.13 1-1/4 3-5/16 20.1 7.030 D100B16 101252 B 16 5.25 3.13 3-1/2 1-1/4 23.1 7.440 D100B17 101253 B 17 5.25 3.13 3-1/2 1-1/4 25.4 7.840 D100B18 101254 B 18 5.50 3.13 3-1/4 1-1/4 29.6 8.240 D100B19 101255 B 19 5.50 3.13 3-1/4 1-1/4 32.4 8.640 D100B20 101256 B 20 5.50 3.38 3-3/4 1-1/4 35.3 9.040 D100B21 101257 B 21 5.50 3.38 3-3/4 1-1/4 38.4 9.440 D100B22 101258 B 22 5.50 3.38 3-3/4 1-1/4 41.3 9.840 D100B23 101259 B 23 5.50 3.38 3-3/4 1-1/4 45.1 10.250 D100B24 101260 B 24 5.50 3.38 3-3/4 1-1/4 48.5 10.650 D100B25 101261 25 B 5.50 3.38 3-3/4 1-1/4 51.5 11.050 D100B26 101262 B 26 5.50 3.38 3-3/4 1-1/4 65.0 12.640 D100B30 101263 B 30 6.00 4.50 4 1-5/8 103 18.630 D100C45 101265 C 45 7.50 5.00 5 2 175 24.600 D100C60 101266 C 60 7.50 5.00 5 2 231 32.570 D100C80 101268 C 80 Maximum Bores shown will accommodate Standard Keyseat and Setscrew over Key seat. Slightly larger Bores are possible with no Ks., Shallow Ks., or S.S. at angle to Ks.

B

B

TYPE B

TYPE C

No.

Descr. +

Part No.

Bore

Wt.

Stock

B

Max.

120 for 1-1/2” Pitch Single Strand Chain No. of Teeth

TYPE BTL

TYPE CTL

FEATURES/BENEFITS PAGE PT12-2

Spkt. O.D.

Description +

12 6.498 120BTL12H-2012 120BTL13H-2517 6.989 13 120BTL14H-2517 7.472 14 120BTL15H-2517 7.956 15 120BTL16H-3020 8.441 16 120BTL17H-3020 8.924 17 120BTL18H-3020 9.407 18 120BTL19H-3020 9.890 19 120BTL20H-3020 10.371 20 120BTL21H-3020 10.853 21 120BTL22H-3020 11.333 22 120BTL23H-3020 11.814 23 12.294 120BTL24H-3020 24 120BTL25H-3020 25 12.774 120BTL26-3020 26 13.254 120BTL28-3020 28 14.213 120BTL30-3020 15.171 30 120BTL32-3020 16.130 32 120BTL35-3020 17.567 35 120BTL36-3020 18.045 36 120CTL45-3535 22.352 45 120CTL60-3535 29.522 60 120CTL70-3535 34.301 70 120CTL80-3535 39.078 80 + “H” suffix indicates Hardened Teeth.

SELECTION PAGES PT12-2

TAPER-LOCK Spkt. Wt. Part w/o No. Bush. 100396 8.0 6.4 100644 7.8 100645 9.6 100646 10.2 100647 11.6 100648 13.2 100649 11.2 100650 16 100397 18 100651 26 104761 28 104762 24 100398 32 104763 30 100652 41 104764 39.7 100399 38 100400 46 100232 75 100401 110 104765 120 100236 144 100238 164 100240

RELATE PRO UCTS PAGES PT12-40

PT12-19

Bore Range

C Hub Dia.

Min.

Max.

3.56

1/2

2-1/8

1.25

4.25

1/2

2-11/16

1.75

5.25

7/8

3-1/4

2.00

6.5

1-3/16

3-15/16

3.50

HT Synchrous Belts

C

C

Spkt. O.D.

Sprockets

2.077 2.077

Type

B

ENGINEERING/TECHNICAL PAGES PT12-42

Conveyor Components

No. Teeth

Engineering

No.

DYNA-SYNC

SPECIFICATION


DYNA-SYNC

SPECIFICATION A.S.A. No.

120 for 1-1/2” Pitch Single Strand Chain REBORABLE–TYPE B

HT Synchrous Belts

TYPE B

.894

TYPE A TYPE C Sprockets

No.

PLATE–TYPE A Bore

No. Tee th

Spkt. O.D.

Description +

Part No.

Wt.

11 12 13 14 15 16 17 18 19 20 21 24 26 30 32 35 36 40 45 60

6.009 6.498 6.986 7.472 7.956 8.441 8.924 9.407 9.890 10.371 10.853 12.294 13.254 15.171 16.130 17.567 18.045 19.959 22.352 29.522

120B11 120B12 120B13 120B14 120B15 120B16 120B17 120B18 120B19 120B20 120B21 120B24 120B26 120B30 120B32 120B35 120B36 120C40 120C45 120C60

105150 105151 105152 105153 105154 105155 105156 105157 105158 105375 105159 105376 105160 105377 105378 105379 105658 105659 105660 105661

7.8 10 13 14 16 20 22 23 25 27 29 35 40 50.2 56.2 63 66.4 92.0 99.2 160

Stock

Max.

1-1/4 1-1/4 1-1/4 1-1/4 1-1/4 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8

2-3/8 2-3/4 3 3-1/4 3-1/4 3-1/2 3-1/2 3-1/2 3-1/2 3-1/2 3-1/2 3-1/2 4-1/8 4-1/8 4-1/8 4-1/8 4-1/8 4-1/8 4-1/8 5-1/4

B 2.13 2.13 2.25 2.25 2.25 2.38 2.38 2.38 2.38 2.38 2.38 2.38 2.50 2.50 2.50 2.50 2.50 3.75 3.75 4.00

C Hub Dia. 3.56 4.13 4.56 4.75 4.75 5.25 5.25 5.25 5.25 5.25 5.25 5.25 6.25 6.25 6.25 6.25 6.25 6.25 6.25 7.00

Spkt. No.

Part No.

Wt.

120A11 120A12 120A13 120A14 120A15 120A16 120A17 120A18 120A19 120A20 120A21 120A24 120A26 120A30 120A32 120A35 120A36 120A40 120A45 120A60

103192 103193 103194 103195 103196 103197 103198 103199 103200 103201 103202 103203 103204 103205 103206 103207 103208 103209 103210 103211

5 6 7 8 10 11 12 14 16 18 19 25 30 41 45 54 55 71 97 170

Stock Bore 1-1/4 1-1/4 1-1/4 1-1/4 1-1/4 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8

1-3/8

120-2 for 1-1/2” Pitch Double Strand Chain REBORABLE–TYPE B & C No. Teeth 2.683 2.683

Conveyor Components

C

C

B

TYPE B

B

TYPE C

Engineering

Maximum Bores shown will accommodate Standard Keyseat and Setscrew over Key seat. Slightly larger Bores are possible with no Ks., Shallow Ks., or S.S. at angle to Ks.

FEATURES/BENEFITS PAGE PT12-2

Spkt. O.D.

Description +

11 6.010 D120B11 12 6 500 D120B12 13 6.990 D120B13 14 7.470 D120B14 15 7.960 D120B15 16 8.440 D120B16 17 8.920 D120B17 18 9.410 D120B18 19 9.890 D120B19 20 10.370 D120B20 21 10.850 D120B21 22 11.330 D120B22 23 11.810 D120B23 24 12.290 D120B24 25 12.770 D120B25 26 13.250 D120B26 30 15.170 D120B30 35 17.570 D120C35 45 22.350 D120C45 60 29.520 D120C60 + “H” suffix indicates Hardened Teeth.

SELECTION PAGES PT12-2

Part No 101270 101271 101272 101273 101274 101275 101276 101277 101278 101279 101280 101281 101282 101283 101284 101285 101286 101287 101288 101289

Bore

C Hub Stock Max. Dia. 13.6 1-1/2 2-3/8 3.75 3.56 17.3 1-1/2 2-3/4 3.75 4.06 21.1 1-1/2 3 3.75 4.50 25.6 1-1/2 3-5/16 3.75 5.00 29.9 1-1/2 3-5/8 3.75 5.50 33.8 1-1/2 3-1/2 3.75 5.25 36.9 1-1/2 3-1/2 3.75 5.25 41.9 1-1/2 3-1/2 3.75 5.25 46.5 1-1/2 3-1/2 3.75 5.25 50.2 1-1/2 3-1/2 3.75 5.25 55.6 1-1/2 3-1/2 3.75 5.50 64.0 1-1/2 3-13/16 4.00 5.75 75.0 1-1/2 4-1/4 4.00 6.50 79.0 1-1/2 4-1/4 4.00 6.50 84.0 1-1/2 4-1/4 4.00 6.50 90.0 1-1/2 4-1/4 4.00 6.50 119 1-1/2 4-1/2 4.00 6.50 148 2 5 6.00 7.50 188 2 5 6.00 7.50 307 2 6 6.25 9.00 See List Price Book MLP for alteration charges. Wt.

RELATE PRO UCTS PAGES PT12-40

PT12-20

B

ENGINEERING/TECHNICAL PAGES PT12-42


140 for 1-3/4” Pitch Single Strand Chain

TYPE B

TYPE A

No. Teeth

12 13 14 15 16 17 18 19 20 21 22 24 25 26 35 36 45 60

7.581 8.150 8.717 9.282 9.847 10.411 10.974 11.538 12.100 12.661 13.221 14.343 14.903 15.463 20.494 21.053 26.077 34.442

140BTL12H-2517 140BTL13H-3020 140BTL14H-3020 140BTL15H-3020 140BTL16H-3020 140BTL17H-3020 140BTL18H-3020 140BTL19H-3020 140BTL20H-3020 140BTL21H-3020 140BTL22H-3020 140BTL24H-3020 140BTL25H-3020 140BTL26-3020 140CTL35-3535 140CTL36-3535 140CTL45-4040 140CTL60-4040

Spkt. O.D.

REBORABLE–SPROCKETS Bore Description Part Wt. + No. Stock Max.

11 7.011 140B11 105161 12 7.581 140B12 105162 13 8.150 140B13 105163 14 8.717 140B14 105164 15 9.282 140B15 105165 16 9.847 140B16 105166 17 10.411 140B17 105167 18 10.974 140B18 105168 19 11.538 140B19 105169 20 12.100 140B20 105380 21 12.661 140B21 105170 26 15.463 140B26 105171 30 17.700 140B30 105382 32 18.820 140B32 105662 35 20.490 140C35 105663 36 21.053 40 23.286 140C40 105664 45 26.077 140C45 105665 48 27.750 140C48 105666 60 34.442 140C60 105667 70 40.020 140C70 105668 140C80 105669 80 45.590 + “H” suffix indicates Hardened Teeth.

11 13 17 19 24 27 29 31 32 36 39 59 70 76 108

1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8

2-3/4 3 3-3/4 3-3/4 4-1/4 4-1/4 4-1/4 4-1/4 4-1/4 4-1/4 4-1/4 4-1/4 4-1/4 4-1/4 5-1/4

121 142 150 220 282 331

1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8

5-1/4 5-1/4 5-1/4 5-3/8 5-3/8 5-3/8

Bore Range

C Hub Dia. 4.25

Min. 1/2

Max. 2-11/16

1.75

5.25

7/8

3-1/4

2.0

6.50

1-3/16

3-15/16

3.5

7.75

1-7/16

4-7/16

4.0

B

PLATE–TYPE A B 2.25 2.25 2.38 2.38 2.50 2.50 2.50 2.50 2.50 2.50 2.50 3.0 3.0 3.0 4.0

C Hub Dia. 4.25 4.25 5.25 5.25 6.25 6.25 6.25 6.25 6.25 6.25 6.25 6.25 6.25 6.25 7.0

Spkt. No.

Part No.

Wt.

140A11 140A12 140A13 140A14 140A15 140A16 140A17 140A18 140A19 140A20 140A21 140A26 140A30 140A32

103212 103213 103214 103215 103216 103217 103218 103219 103220 103221 103222 103223 103224 102250

7 9 10 11 12 15 17 19 21 23 26 41 56 60

Stock Bore

1-3/8

1-3/8 140A36 103225 83 4.0 7.0 140A40 103226 102 4.0 7.0 140A45 103227 122 4.0 7.0 140A48 102251 134 5.0 7.50 140A60 103228 230 1-3/8 5.0 7.50 140A70 102252 292 5.0 7.50 140A80 102253 402 See List Price Book MLP for alteration charges.

TYPE C

FEATURES/BENEFITS PAGE PT12-2

SELECTION PAGES PT12-2

RELATE PRO UCTS PAGES PT12-40

PT12-21

HT Synchrous Belts

Description +

Sprockets

TYPE CTL

Spkt. O.D.

ENGINEERING/TECHNICAL PAGES PT12-42

Conveyor Components

TYPE BTL

No. Teeth

TAPER-LOCK Wt. Part w/o No. Bush. 100653 7.6 100654 9.6 100655 11.3 100656 12.7 100657 14.6 100658 17.5 100659 19.3 100660 21.2 104769 26 100661 28 104770 34 104771 40 104772 43 100662 45 100264 80.3 104775 90 100266 120 100268 200

Engineering

No.

DYNA-SYNC

SPECIFICATION


DYNA-SYNC

SPECIFICATION No.

140-2 for 1-3/4” Pitch Double Strand Chain REBORABLE–TYPE B & C C Hub Stock Max. Dia. 13 8.150 B D140B13 101290 29 1-1/2 3-1/2 3.75 5.31 14 8.720 B D140B14 101291 34.8 1-1/2 4 3.75 5.88 15 9.280 B D140B15 101292 42.5 1-1/2 3-1/2 3.75 5.25 16 9.850 B D140B16 101293 48.1 1-1/2 4-1/4 4.0 6.25 17 10.410 B D140B17 101294 57.5 1-1/2 4-1/4 4.0 6.25 18 10.980 B D140B18 101295 65.6 1-5/8 4-3/4 4.0 7.0 19 11.540 B D140B19 101296 72.0 1-5/8 4-3/4 4.0 7.0 20 12.100 B D140B20 101297 76.0 1-5/8 4-3/4 4.0 7.0 21 12.660 B D140B21 101298 82.0 1-5/8 4-3/4 4.0 7.0 22 13.220 B D140B22 101299 94.0 1-5/8 4-3/4 4.0 7.0 23 13.780 B D140B23 101300 100 1-5/8 4-3/4 4.0 7.0 24 14.340 B D140B24 101301 104 1-5/8 4-3/4 4.0 7.0 25 14.900 B D140B25 101302 120 1-5/8 4-3/4 4.0 7.0 26 15.460 B D140B26 101303 128 1-5/8 4-3/4 4.0 7.0 35 20.490 C D140C35 101304 180 2 5 6.0 7.50 45 26.080 C D140C45 101305 232 2 5 5.0 7.50 60 34.440 C D140C60 101306 372 2 6 6.25 9.0 Maximum Bores shown will accommodate Standard Keyseat and Setscrew over Key seat. Slightly larger Bores are possible with no Ks., Shallow Ks., or S.S. at angle to Ks. No. Teeth

2.818

2.818

HT Synchrous Belts

C

Sprockets

No.

C

B

B

TYPE B

TYPE C

Spkt. O.D.

Type

Description +

Part No.

Bore

Wt.

B

160 for 2” Pitch Single Strand Chain No. Teeth

Conveyor Components

TYPE BTL

Spkt. O.D.

Description +

11 8.012 160BTL11H-2517 12 8.664 160BTL12H-3020 13 9.314 160BTL13H-3020 14 9.962 160BTL14H-3020 15 10.608 160BTL15H-3535 17 11.898 160BTL17H-3535 18 12.542 160BTL18H-3535 19 13.186 160BTL19H-3535 20 13.828 160BTL20H-3535 21 14.470 160BTL21H-3535 23 15.752 160BTL23H-3535 24 16.390 160BTL24H-3535 26 17.672 160BTL26-3535 35 23.422 160CTL35-4040 36 24.060 160CTL36-4040 60 39.362 160CTL60-4545 + “H” suffix indicates Hardened Teeth.

TAPER-LOCK Wt. Part w/o No. Bush. 100663 7.7 100664 11.5 100665 14.2 100666 17.1 100667 27.4 100669 33.9 100670 38.4 100671 41.7 104781 57 100672 50 104783 72 100407 85 100673 88 100294 106 104789 130 100298 253

Bore Range

C Hub Dia. 4.25

Min. 1/2

Max. 2-11/16

1.75

5.25

7/8

3-1/4

3.0

6.50

1-3/16

3-15/16

3.5

6.50

1-3/16

3-15/16

3.5

7.75 7.75 8.75

1-7/16 1-7/16 1-15/16

4-7/16 4-7/16 4-15/16

4.0 4.0 4.5

B

Engineering

TYPE CTL

FEATURES/BENEFITS PAGE PT12-2

SELECTION PAGES PT12-2

RELATE PRO UCTS PAGES PT12-40

PT12-22

ENGINEERING/TECHNICAL PAGES PT12-42


160 for 2” Pitch Single Strand Chain

TYPE B

No. Teeth

Spkt. O.D.

Description +

Part No.

Wt.

11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 30 35 40 45 54 60 70 80

8.012 8.664 9.314 9.962 10.608 11.254 11.898 12.542 13.186 13.830 14.470 15.110 15.750 16.390 17.030 17.670 18.310 18.950 20.230 23.420 26.610 29.800 35.540 39.360 45.730 52.100

160B11 160B12 160B13 160B14 160B15 160B16 160B17 160B18 160B19 160B20 160B21 160B22 160B23 160B24 160B25 160B26 160B27 160B28 160B30 160C35 160C40 160C45 160C54 160C60 160C70 160C80

105172 105173 105174 105175 105176 105177 105178 105179 105180 105670 105386 105383 105671 105384 105672 105385 105673 105674 105387 105675 105676 105677 105678 105679 105680 105681

17 21 29 31 39 41 44 48 52 56 59 65 68 77 81 86 91 98 108 154 196 234 276 329 446 612

1.156

TYPE A

TYPE C

No.

PLATE–TYPE A Bore

Stock

Max.

1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8

3-1/4 3-3/4 4 4-1/4 5-1/4 5-1/4 5-1/4 5-1/4 5-1/4 5-1/4 5-1/4 5-1/4 5-1/4 5-1/4 5-1/4 5-1/4 5-1/4 5-1/4 5-1/4 5-1/2 5-1/2 5-1/2 5-1/2 5-1/2 5-1/2 5-1/2

B 2.50 2.63 2.75 2.75 2.75 2.75 2.75 2.75 2.75 2.75 2.75 2.75 2.75 3.0 3.0 3.0 3.0 3.0 3.0 4.50 4.50 5.0 5.0 5.0 5.0 6.0

C Hub Dia. 4.75 5.25 6.0 6.25 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0

Spkt. No.

Part No.

Wt.

160A11 160A12 160A13 160A14 160A15 160A16 160A17 160A18 160A19 160A20 160A21 160A22 160A23 160A26 160A27 160A28 160A30 160A35 160A40 160A45 160A54 160A60 160A70 160A80

103229 103230 103231 103232 103233 103234 100235 103236 103237 102254 103238 103295 102255 103239 102256 102257 103240 103241 103242 103243 102258 103244 102259 102260

12 14 16 20 23 26 29 33 35 38 42 46 50 65 71 77 90 121 138 204 294 366 507 656

Stock Bore

1-3/8

HT Synchrous Belts

REBORABLE–TYPE B

1-3/8

Sprockets

No.

DYNA-SYNC

SPECIFICATION

160-2 for 2” Pitch Double Strand Chain

C

B TYPE B

C

B

TYPE C

Maximum Bores shown will accommodate Standard Keyseat and Setscrew over Key seat. Slightly larger Bores are possible with no Ks., Shallow Ks., or S.S. at angle to Ks.

FEATURES/BENEFITS PAGE PT12-2

No. Teeth

Type

Spkt. O.D.

Description +

13 B 9.310 D160B13 14 B 9.960 D160B14 15 B 10.610 D160B15 16 B 11.260 D160B16 17 B 11.900 D160B17 18 B 12.540 D160B18 19 B 13.190 D160B19 20 B 13.830 D160B20 21 B 14.470 D160B21 22 B 15.110 D160B22 23 B 15.750 D160B23 24 B 16.390 D160B24 25 B 17.030 D160B25 26 B 17.670 D160B26 35 C 23.420 D160C35 45 C 29.800 D160C45 60 C 39.360 D160C60 + “H” suffix indicates Hardened Teeth.

SELECTION PAGES PT12-2

Bore

Part No.

Wt.

101307 101308 101309 101310 101311 101312 101313 101314 101315 101316 101317 101318 101319 101320 101321 101322 101323

48 58 68 75 91 96 107 119 130 141 157 171 187 201 306 431 564

RELATE PRO UCTS PAGES PT12-40

PT12-23

Stock

Max.

2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2

3-1/2 3-1/2 3-1/2 4-3/4 4-3/4 4-3/4 4-3/4 4-3/4 5 5 5 5 5 5 6 6-3/4 6-3/4

B 4.75 4.75 4.75 4.75 4.75 4.75 4.75 4.75 5.0 5.0 5.0 5.0 5.0 5.0 6.25 7.13 7.13

C Hub Dia. 5.25 5.25 5.25 7.0 7.0 7.0 7.0 7.0 7.50 7.50 7.50 7.50 7.50 7.50 9.0 10.0 10.0

ENGINEERING/TECHNICAL PAGES PT12-42

Engineering

3.434

Conveyor Components

REBORABLE–TYPE B & C 3.434


DYNA-SYNC

SPECIFICATION No.

180 for 2-1/4” Pitch Single Strand Chain REBORABLE–TYPE B & C

1.301

No. Type Teeth

HT Synchrous Belts

TYPE A

TYPE C

Sprockets

TYPE B

No.

11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 28 30 35 40 45 54 60

B B B B B B B B B B B B B B B B C C C C C C

PLATE–TYPE A Bore

Spkt. O.D.

Description +

Part No.

Wt.

9.010 9.750 10.480 11.210 11.930 12.660 13.390 14.110 14.830 15.560 16.280 17.000 17.720 18.440 19.160 21.320 22.760 26.350 29.940 33.530 39.980 44.280

180B11 180B12 180B13 180B14 180B15 180B16 180B17 180B18 180B19 180B20 180B21 180B22 180B23 180B24 180B25 180B28 180C30 180C35 180C40 180C45 180C54 180C60

105682 105683 105684 105685 105686 105687 105688 105689 105690 105691 105692 105693 105694 105695 105696 105697 105698 105699 105745 105746 105747 105748

29 32 40 44 48 52 58 63 74 81 83 92 99 105 113 135 180 222 270 315 477 489

Stock

Max.

1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8

3-5/8 4 5-1/4 5-1/4 5-1/4 5-1/4 5-1/4 5-1/4 5-3/8 5-3/8 5-3/8 5-3/8 5-3/8 5-3/8 5-3/8 5-1/2 5-3/4 5-3/4 5-3/4 6 6 6-1/2

B 2.94 2.94 3.13 3.13 3.13 3.13 3.13 3.13 3.38 3.38 3.38 3.38 3.38 3.38 3.38 3.69 4.38 4.38 4.38 5.0 5.0 5.38

C Hub Dia. 5.50 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7.50 7.50 7.50 7.50 7.50 7.50 7.50 8.0 8.50 8.50 8.50 9.0 9.0 9.50

Spkt. No.

Part No.

Wt.

Stock Bore

180A11 180A12 180A13 180A14 180A15 180A16 180A17 180A18 180A19 180A20 180A21 180A22 180A23 180A24 180A25 180A28 180A30 180A35 180A40 180A45 180A54 180A60

102261 102262 102263 102264 102265 102266 102267 102268 102269 102270 102271 102272 102273 102274 102275 102276 102277 102278 102279 102280 102281 102282

14 16 20 24 28 32 37 43 47 53 57 62 69 77 84 104 120 172 229 284 420 505

1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8

200 for 2-1/2” Pitch Single Strand Chain REBORABLE–TYPE B & C

PLATE–TYPE A C Stock Spkt. Part No. Spkt. Description Part Wt. Type Wt. B Hub Bore No. No. Teeth O.D. + No. Stock Max. Dia. 5.50 200A10 102283 16 1-3/8 3.0 26 1-3/8 3-3/4 105750 B 200B10 9.200 10 200A11 102284 20 1-3/8 6.0 3.0 4 33 1-3/8 B 200B11 105751 10.020 11 200A12 102285 24 1-3/8 6.0 3.0 4 37 1-3/8 B 200B12 105752 10.830 12 6.25 200A13 102286 30 1-3/8 3.0 46 1-3/8 4-1/4 B 200B13 105753 11.640 13 7.50 200A14 102287 32 1-3/8 3.44 59 1-3/8 5-3/8 B 105754 200B14 12.460 14 7.50 200A15 102288 40 1-3/8 3.44 64 1-3/8 5-3/8 B 105755 200B15 13.260 15 7.50 200A16 102289 46 1-3/8 3.44 72 1-3/8 5-3/8 B 105756 200B16 14.070 16 7.50 200A17 102290 51 1-3/8 3.44 76 1-3/8 5-3/8 B 105757 200B17 14.870 17 7.50 200A18 102291 57 1-3/8 3.44 84 1-3/8 5-3/8 B 105758 200B18 15.680 18 7.50 200A19 102292 65 1-3/8 3.44 91 1-3/8 5-3/8 B 105759 200B19 16.480 19 7.50 200A20 102293 72 1-3/8 3.44 98 1-3/8 5-3/8 B 105760 200B20 17.290 20 7.50 200A21 102294 82 1-3/8 3.44 106 1-3/8 5-3/8 B 105761 200B21 18.090 21 8.50 200A22 102295 88 1-3/8 4.0 131 1-3/8 5-3/4 B 105762 200B22 18.890 22 8.50 200A23 102296 95 1-3/8 4.0 136 1-3/8 5-3/4 B 105763 200B23 19.690 23 8.50 200A24 102297 105 1-3/8 4.0 142 1-3/8 5-3/4 B 105764 200B24 20.490 24 8.50 200A25 102298 113 1-3/8 4.0 153 1-3/8 5-3/4 B 105765 200B25 21.290 25 8.50 200A26 102299 124 1-3/8 4.50 178 1-3/8 5-3/4 C 105766 200C26 22.090 26 8.50 200A28 102300 144 1-3/8 4.50 195 1-3/8 5-3/4 C 105767 200C28 23.690 28 8.50 200A30 102301 167 1-3/8 4.50 212 1-3/8 5-3/4 C 105768 200C30 25.290 30 8.50 200A32 102302 195 1-3/8 4.50 220 1-3/8 5-3/4 C 105769 200C32 26.880 32 8.50 200A35 102303 227 1-3/8 4.50 254 1-3/8 5-3/4 C 105770 200C35 29.280 35 200A40 102304 301 1-3/8 9.0 5.0 6 320 1-3/8 C 105771 200C40 33.270 40 200A45 102305 390 1-3/8 9.0 5.0 6 364 1-3/8 C 105772 200C45 37.250 45 9.50 200A54 102306 555 1-3/8 5.50 512 1-3/8 6-1/2 C 105773 200C54 44.420 54 9.50 200A60 102307 692 1-3/8 5.50 654 1-3/8 6-1/2 C 105774 200C60 49.200 60 + “H” suffix indicates Hardened Teeth. See List Price Book MLP for alteration charges. Maximum Bores shown will accommodate Standard Keyseat and Setscrew over Key seat. Slightly larger Bores are possible with no Ks., Shallow Ks., or S.S. at angle to Ks. Bore

Conveyor Components

TYPE B 1.389

TYPE A Engineering

TYPE C

FEATURES/BENEFITS PAGE PT12-2

SELECTION PAGES PT12-2

RELATE PRO UCTS PAGES PT12-40

PT12-24

ENGINEERING/TECHNICAL PAGES PT12-42


240 for 3” Pitch Single Strand Chain REBORABLE–TYPE B & C

TYPE A

TYPE B

Spkt. O.D.

Description +

Part No.

Wt.

10 11.030 240B10 105775 49 11 12.020 240B11 105776 66 12 13.000 240B12 105777 72 13 13.970 240B13 105778 81 14 14.940 240B14 105779 88 15 15.910 240B15 105780 98 16 16.880 240B16 105781 120 17 17.850 240B17 105782 137 18 18.810 240B18 105783 142 19 19.780 240B19 105784 154 20 20.740 240B20 105785 169 21 21.710 240B21 105786 186 25 25.550 240B25 105787 254 30 30.340 240C30 105788 398 35 35.130 240C35 105789 527 40 39.920 240C40 105790 672 45 44.700 240C45 105791 850 54 53.310 240C54 105792 1148 60 59.040 240C60 105793 1419 + “H” suffix indicates Hardened Teeth.

Type B B B B B B B B B B B B B C C C C C C

Stock

Max.

1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8

4-1/2 4-3/4 4-3/4 5-3/8 5-3/8 5-3/8 5-1/2 5-1/2 5-1/2 5-1/2 5-1/2 5-1/2 5-1/2 6 6 7 7 7 7

B 3.38 3.06 3.06 3.88 3.88 3.88 4.13 4.13 4.13 4.13 4.13 4.13 4.13 6.25 6.25 6.75 6.75 6.75 6.75

C Hub Dia. 6.25 7.0 7.0 7.50 7.50 7.50 8.0 8.0 8.0 8.0 8.0 8.0 8.0 9.0 9.0 10.0 10.0 10.0 10.0

Spkt. No. 240A10 240A11 240A12 240A13 240A14 240A15 240A16 240A17 240A18 240A19 240A20 240A21 240A25 240A30 240A35 240A40 240A45 240A54 240A60

Part No.

Wt.

102308 30 102309 37 102310 45 102311 54 102312 62 102313 68 102314 82 102315 93 102316 108 102317 120 102318 128 102319 148 102320 208 102321 310 102322 416 102323 548 102324 702 102325 1022 102326 1268

Stock Bore 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8 1-3/8

Sprockets

No. Teeth

1.738

PLATE–TYPE A Bore

HT Synchrous Belts

No.

DYNA-SYNC

SPECIFICATION

Engineering

Conveyor Components

TYPE C

FEATURES/BENEFITS PAGE PT12-2

SELECTION PAGES PT12-2

RELATE PRO UCTS PAGES PT12-40

PT12-25

ENGINEERING/TECHNICAL PAGES PT12-42


DYNA-SYNC

SPECIFICATION Double Single Sprockets No. 40

HT Synchrous Belts

No Teeth 18 19 20 21 22 23 24

Spkt. O.D. 3.136 3.300 3.460 3.620 3.780 3.940 4.100

No. 50 No Teeth 17 18 19 20 21 22 23 24

Sprockets

L1 W

L2

E

Conveyor Components

C TYPE ATL TAPER-LOCK

Spkt. O.D. 3.200 3.920 4.120 4.320 4.520 4.720 4.920 5.120

No. 60 No Teeth 17 18 19 20 21 22 23

Spkt. O.D. 4.460 4.700 4.950 5.190 5.430 5.910 6.150

No. 80 No Teeth 17 18 19 20 21 22 23

Spkt. O.D. 5.950 6.270 6.590 6.910 7.240 7.560 7.880

C=1.13 W=.284 E Dim. 2.31 2.50 2.63 2.78 2.94 3.09 3.27 C=1.31 W=.343 E Dim. 2.69 2.89 3.08 3.28 3.48 3.69 3.89 4.08

TAPER-LOCK* Spkt. No. .... DS40ATL19H DS40ATL20H DS40ATL21H .... DS40ATL23H DS40ATL24H

Bushing: No. Max. Bore ... ... 1-1/4 1215 1-1/4 1215 1-11/16 1615 ... ... 1-11/16 1615 1-11/16 1615

Part No. .... 101450 101451 101452 .... 101453 101454

L Dim. ... 1.41 1.41 1.41 ... 1.41 1.41

Wt. w/o Bush. ... 1.1 1.3 1.3 ... 1.5 1.7

L Dim. 1.64 1.64 1.64 ... 1.64 ... 1.64 1.64

Wt. w/o Bush. 1.8 2.2 2.7 ... 3.3 ... 3.7 4.1

L Dim. 1.94 1.94 1.94 1.94 1.94 1.94 1.94

Wt. w/o Bush. 4.5 5.0 5.8 5.6 6.4 7.3 8.2

L Dim. 2.19 2.19 2.19 2.19 2.19 ... 2.19

Wt. w/o Bush. 7.6 8.7 9.7 10 12 ... 14.5

L Dim. 2.69 2.69 2.69 2.69 ... 2.69

Wt. w/o Bush. 13 14 16 20 ... 27.5

TAPER-LOCK* Spkt. No. DS50ATL17H DS50ATL18H DS50ATL19H .... DS50ATL21H .... DS50ATL23H DS50ATL24H

Part No. 101455 101456 101457 .... 101458 .... 101459 101460

C=1.48 W=.459 E Dim. 3.22 3.47 3.70 3.95 4.19 4.67 4.91

Spkt. No. DS60ATL17H DS60ATL18H DS60ATL19H DS60ATL20H DS60ATL21H DS60ATL23H DS60ATL24H

Part No. 101461 101462 101463 101464 101465 101466 101467

C=1.63 W=.575 E Dim. 4.31 4.75 4.95 5.28 5.59 ... 6.23

Spkt. No. DS80ATL17H DS80ATL18H DS80ATL19H DS80ATL20H DS80ATL21H .... DS80ATL23H

Part No. 101468 101469 101470 101471 101472 .... 101473

Bushing: No. Max. Bore 1615 1-11/16 1-11/16 1615 1-11/16 1615 ... ... 2-1/8 2012 ... ... 2-1/8 2012 2-1/8 2012

TAPER-LOCK* Bushing: No. Max. Bore 1-11/16 1615 2-1/8 2012 2-1/8 2012 2-11/16 2517 2-11/16 2517 2-11/16 2517 2-11/16 2517

TAPER-LOCK* Bushing: No. Max. Bore 2-11/16 2517 2-11/16 2517 3-1/4 3020 3-1/4 3020 3-1/4 3020 ... ... 3-1/4 3020

C=2 TAPER-LOCK* W=.692 Bushing: No Spkt. E Spkt. Part Teeth O.D. Dim. No. No. No. Max. Bore 2-11/16 2517 101474 DS100ATL16H 5.00 7.030 16 3-1/4 3020 101475 DS100ATL17H 5.41 7.440 17 3-1/4 3020 101476 DS100ATL18H 5.80 7.840 18 3-1/4 3020 101477 DS100ATL19H 6.20 8.240 19 20 8.640 6.61 .... .... ... ... 21 9.040 7.00 DS100ATL21H 101478 3020 3-1/4 * TAPER-LOCK double single sprockets have hardened teeth.

No. 100

Engineering FEATURES/BENEFITS PAGE PT12-2

SELECTION PAGES PT12-2

RELATE PRO UCTS PAGES PT12-40

PT12-26

ENGINEERING/TECHNICAL PAGES PT12-42


• Special pitch diameter for Extended Pitch Roller Chain • Chain engages every other tooth • Effective no. of teeth equals 1/2 the actual no. of teeth. • Odd no. of teeth preferred to automatically balance wear on sprocket. • Use standard TAPER-LOCK sprockets for 35 for more teeth.

Part No.

2040BTL17H-1008 2040BTL19H-1210 2040BTL23H-1610 2040BTL25H-1610 2040BTL31H-1610

104877 104878 104879 104880 104881

No. Effective Outside Max. No. of of Diam. Bore. Teeth Teeth 1 2.97 8-1/2 17 1-1/4 3.29 9-1/2 19 1-11/16 3.93 11-1/2 23 1-11/16 4.26 12-1/2 25 1-11/16 5.85 17-1/2 35

for 1-1/4" Double Pitch Drive or Conveyor Chain

2050/C2050 Sprocket No.-Bushing +

Part No.

2050BTLI7H-1210 2050BTL18H-1210 2050BTL19H-1610 2050BTL20H-1610 2050BTL21H-1610 2050BTL25-2012 2O50BTL35-2012

104882 104883 104884 104885 104886 104887 104888

No. Effective Outside Max. No. of of Diam. Bore. Teeth Teeth 1-1/4 3.71 8-1/2 17 1-1/4 3.20 9 18 1-11/16 4.11 9-1/2 19 1-11/16 4.32 10 20 2-11/16 4.52 10-1/2 21 2-1/8 5.32 12-1/2 25 2-1/8 7.32 17-1/2 35

No. Effective Outside Max. No. of of Diam. Bore. Teeth Teeth 2-1/8 5.95 8-1/2 2080BTL17-2012 104898 17 2-11/16 6.59 9-1/2 2080BTL19-2517 104899 19 2-11/16 6.91 10 2080BTL20-2517 104900 20 2-11/16 7.24 10-1/2 2080BTL21-2517 104901 21 2080BTL23-2517 2-11/16 7.88 11-1/2 104902 23 2080BTL25-2517 2-11/16 8.52 12-1/2 104903 25 2080BTL27-2517 2-11/16 9.16 13-1/2 104904 27 2080BTL31-2517 10.43 2-11/16 15-1/2 104905 31 2080BTL35-2517 11.71 2-11/16 17-1/2 104906 35 TAPER-LOCK extended pitch sprockets are standard non-stock. Allow 2-4 weeks for delivery. Sprocket No.-Bushing +

Part No.

for 1-1/2" Double Pitch Drive or Conveyor Chain

2060/C2060

No. Effective Outside Max. No. of of Diam. Bore. Teeth Teeth 1-11/16 4.46 8-1/2 2060BTL17H-1610 104889 17 1-11/16 4.95 9-1/2 2060BTL19H-1610 104890 19 1-11/16 5.19 10 2060BTL20-1610 104891 20 2-1/8 5.43 10-1/2 2060BTL21-2012 104892 21 2060BTL23-2012 2-1/8 5.91 11-1/2 104893 23 2060BTL25-2012 2-1/8 6.39 12-1/2 104894 25 2060BTL27-2012 2-1/8 6.87 13-1/2 104895 27 2060BTL31-2012 2-1/8 7.83 15-1/2 104896 31 2060BTL35-2012 2-1/8 8.78 17-1/2 104897 35 + “H” suffix indicates Hardened Teeth.

FEATURES/BENEFITS PAGE PT12-2

Part No.

SELECTION PAGES PT12-28

Engineering

Sprocket No.-Bushing +

RELATED PRODUCTS PAGES PT12-40

PT12-27

Sprockets

Sprocket No.-Bushing +

for 2" Double Pitch Drive or Conveyor Chain

2080/C2080

Conveyor Components

for 1" Double Pitch Drive or Conveyor Chain

2040/C2040

DYNA-SYNC

TAPER-LOCK Type B Extended Pitch Sprockets

HT Synchrous Belts

SPECIFICATION

ENGINEERING/TECHNICAL PAGES PT12-42


DYNA-SYNC

SELECTION Roller Chain Drive Selection 3. Calculate Design Horsepower: Motor HP x Service Factor, or normal running HP x Service Factor.

HT Synchrous Belts

EASY SELECTION METHOD 1. Determine Class of Service: Refer to tabulation below, or select from the following: Class A: Fairly uniform running load. Start-up and peak loads occur infrequently. Class B: Variable running load. Higher starting and peak loads, occurring more frequently. Class C: Heavy starting loads. Peak loads and overloads occurring frequently. 2. Select Service Factor:

Sprockets

Type of Input Power Class Internal Combustion Electric Internal Combustion of Engine with or Engine with Service Hydraulic Drive Turbine Mechanical Drive A B C

1.0 1.2 1.4

1.0 1.3 1.5

1.2 1.4 1.7

4. Determine Chain Size and Smaller (Usually the Driver) sprocket number of teeth: Refer to "Recommended Smaller Sprocket" table on page PT12-30, PT12-31. Start at column that is at or above the calculated design HP. Trace down to the row that includes the RPM of the faster (Usually the Driver) shaft. The chain pitch and sprocket No. of Teeth are listed at this intersection. 5. Calculate Drive Ratio: Faster shaft Rpm divided be Slower shaft RPM. 6. Determine Size of Large Sprocket: Multiply smaller sprocket No.teeth by ratio. Select Closest stock available sprocket. 7. Calculate Chain Length "L": (D - d)2 L = 2c + 1.57 (D + d) + 4c Where: D = Pitch dia. large sprocket, (see page ) d = Pitch dia.small sprocket,(see page ) c = Proposed center distance (Accuracy is within .15% chain length) Divide chain length (inches) by chain pitch to determine number of pitches in the chain. Good practice is to use an even number of pitches, including connecting link.

Class of Service for Driven Machine C

Conveyor Components Engineering

Agitators, liquid or semi-liquid stock, paddle or propeller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bakery Machinery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Beaters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Blowers, Centrifugal . . . . . . . . . . . . . . . . . . . . . . . . . . . . Boat Paddle Wheels or Propellers . . . . . . . . . . . . . . . . Centrifuges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clay Working Machinery: Extruders, Granulators, Mixers, Pug Mills, Rolls Briquette Machine, Presses . . . . . . . . . . . . . . . . . . . . Compressors: Centrifugal, Rotary . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reciprocating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Conveyors: Uniformly or loaded. . . . . . . . . . . . . . . . . . . . . . . . . . . . Irregularly fed or loaded. . . . . . . . . . . . . . . . . . . . . . . . Reciprocating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cookers, Cereal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cranes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Crushers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Elevators: Uniformly fed or loaded. . . . . . . . . . . . . . . . . . . . . . . . Irregularly fed or loaded. . . . . . . . . . . . . . . . . . . . . . . Fans: Centrifugal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mine, Positive Blowers, Propeller . . . . . . . . . . . . . . . Feeders, Reciprocating. . . . . . . . . . . . . . . . . . . . . . . . . . Flour, Feed or Cereal Mill Machinery . . . . . . . . . . . . . Generators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hogs for Refuse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Kettles, Brew. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Kilns and Dryers, rotary. . . . . . . . . . . . . . . . . . . . . . . . . . Laundry Machinery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

FEATURES/BENEFITS PAGE PT12-2

C A B B A C C B C B C A B C A B C A B A C C B A C A B B

Line Shafts: Light or normal service . . . . . . . . . . . . . . . . . . . . . . . . . Unevenly loaded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Machines, Non-Reversing: Even load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pulsating load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Impact load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mills: Ball, Pebble, Rod, Tube . . . . . . . . . . . . . . . . . . . . . . . . Blooming, Hammer, Hardinge, Rolling . . . . . . . . . . . Paper Machinery: Agitators, Calenders, Dryers, Jordan Engines, Paper Machines, Pulp Grinders . . . . . . . . . . . . . . . . . . . . . . Beaters, Chippers, Nash Pumps, Washers, Winder Drums, Yankee Dryers . . . . . . . . . . . . . . . . . . . . . . . . Presses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printing Machinery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pumps: Centrifugal, Gear, Rotary . . . . . . . . . . . . . . . . . . . . . . Dredge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reciprocating, 1 or 2 cylinder . . . . . . . . . . . . . . . . . . Reciprocating, 3 or more cylinder . . . . . . . . . . . . . . . . Rubber Plant Machinery: Banbury Mills, Calenders, Mixers . . . . . . . . . . . . . . . . Screens: Air Washing, Water . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rotary (Stone or Gravel), Vibrating . . . . . . . . . . . . . . Textile Machinery: Batcher, Calender, Dry Can, Dyeing Machinery. Loom, Mangel, Napper, Soaper, Spinner, Tenter Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Card Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Woodworking Machinery . . . . . . . . . . . . . . . . . . . . . . . . .

SPECIFICATION PAGES PT12-

RELATE PRO UCTS PAGES PT12-40

PT12-28

A B A B C B C B C C B A C C B C A B

B C B

ENGINEERING/TECHNICAL PAGES PT12-42


SLOW SPEED DRIVES

A chain drive is required for a tumbling barrel for metal stampings. The barrel is to run at 24 RPM from a speed reducer output of 77 RPM. Center distance is 50". Input power is from a 5 HP electric motor. Starting loads are heavy, peak loads and overloads are frequent. 1. Service Factor: Class of service is not listed in table, so refer to Class Description. Class C is appropriate. Service Factor Table shows 1.5 Class C driven by an electric motor.

Where linear speed of the chain is under 100 fpm and loading is uniform, roller chain drives may be selected on the basis of chain pull rather than horsepower rating. This often results in significant savings. When chain length is more than 50 pitches, the maximum applied load may be as great as 1/7 of the ultimate tensile strength of the chain for speeds below 50 fpm to 100 fpm. Unusual load variations of peak loads require other methods of determining the maximum applied load. Chain pull may be calculated by the following formula: Design HP x 126,000 Chain Pull (lbs.) = rpm x Pitch diam. Table below offers a simplified method of determining allowable chain pull for slow speed drives. The table also shows revolutions per minute for a given pitch diameter at 50 and 100 feet per minute. Average tensile strength for all popular roller chain is given on PT12-44.

2. Design HP: Motor HP x S.F. 5 x 1.5 = 7.5 Design HP. 3. Chain and Small Sprocket Size: Refer to the 7-1/2 HP column of the Easy Selection Table. Trace down to the row that includes 77 RPM, "71-80 RPM". No. 100 chain and sprocket with 15 teeth is shown: select 100BTL15. 4. Drive Ratio: 77/24 = 3.21:1. 5. Large Sprocket: 15 x 3.21 = 48.15. Select a 48 tooth driven sprocket, 100BTL48, which is a stock size. 6. Chain Length:

DYNA-SYNC

SELECTION EXAMPLE

HT Synchrous Belts

SELECTION

Information for Slow Speed Drives

Choose 112 or 114 Pitches of chain, including Conn Link. 7. Verify that sprockets will fit shaft sizes.

40 50 60 80 100 120 140 160 180 200 240

DESIGN NOTES Small Sprocket Size: The higher RPM and the fewer the number of teeth on the small sprocket, the greater the wear. This leads to some general guidelines: • Use at least 17 teeth sprocket for 100+ RPM. • Avoid high ratios that require very small sprockets Lubrication: Chain drives must be lubricated and kept clean. The most effective method to accomplish this is to use an oil-tight chain guard with an oil sump. Manual lu brication is effective on slower speed drives, but exposure to dirt and contamination will be a problem for the drive. Design Refinement: The "Easy Selection Method" is a good starting point for further design refinement, if desired. Refer to the Chain HP Rating Tables on the following pages for more precise ratings. also refer to "Slow Speed Drives" which follows this section.

528 871 1214 2071 3428 4857 6571 8285 11,428 13,571 18,571

462 762 1062 1812 3000 4250 5750 7250 10,000 11,875 16,250

RPM for a Given Pitch Diam. at Various Speeds P.D. in inches

@ 50 fpm RPM

2 3 4 5 6 7 8 9 10 11 12

95.0 63.6 47.7 38.2 31.8 27.3 23.9 21.2 19.1 17.3 15.9

@ 100 fpm RPM 191.0 127.2 95.5 76.4 63.7 54.6 47.8 42.4 38.2 34.7 31.8

Note: Smaller sprockets can be used on slow speed drives as the effects of chordal action are not pronounced. However, small sprockets of fewer than 9 teeth should be avoided.

MULTIPLE STRAND CHAIN DRIVES Single Strand drives offer cost and availability advantages, and are more easily assembled. Multiple strand drives can be used to solve design problems of greater HP capacity or space constraints. For multiple strand drives, divide the calculated Design HP by the factors below, and select from the ratings for single strand drives:

Sprockets

Allowable Chain Pull for STD. Chain Max. Chain Pull Chain @ 50 fpm @ 50-100 No. or less fpm

Conveyor Components

(19.113 - 6.013)2 4 x 50 L = 140.31" (No.100 Chain has 1-1/4 or 1.25" Pitch) Length in pitches = 140.31/1.25 = 112.48 pitches. L = 2(50) + 1.57(19.113 + 6.013) +

FEATURES/BENEFITS PAGE PT12-2

SPECIFICATION PAGES PT12-

RELATE PRO UCTS PAGES PT12-40

PT12-29

1.0 1.9 2.8

ENGINEERING/TECHNICAL PAGES PT12-42

Engineering

Multiple Strand Factors Single: Double Triple:


DYNA-SYNC

SELECTION Easy Selection Table RECOMMENDED SMALL SPROCKET

HT Synchrous Belts Sprockets Conveyor Components

RPM of small Sprocket 951-1000 901-950 851-900 801-850 751-800 701-750 651-700 601-650 551-600 501-550 471-500 441-470 411-440 381-410 351-380 321-350 301-320 281-300 261-280 241-260 221-240 201-220 181-200 161-180 151-160 141-150 131-140 121-130 111-120 101-110 91-100 81-90 71-80 61-70 51-60 46-50 41-45 35-40 30-35 23-29 17-22 12-16 8-11 5-7

Chain Size and No. of Teeth for Design HP 1/4 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 40 40 40 40 40 50 50 60 80

17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 15 15 15 15 15 15 15 15 15 17 13 13 13 13 14 13 15 14 13

1/3 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 40 40 40 40 40 50 50 60 60 80

17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 15 15 15 15 15 15 15 17 19 13 13 13 14 16 13 14 13 18 13

1/2 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 40 40 40 40 40 40 40 40 40 40 50 50 50 60 60 80 100

17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 18 20 21 22 23 13 13 15 15 15 15 15 15 16 18 13 13 16 13 18 13 13

3/4 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 40 40 40 40 40 40 40 40 40 40 40 50 50 50 50 50 60 60 80 80 100

17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 18 18 18 18 18 18 18 15 15 16 19 13 13 16 16 18 14 19 13 18 13

1 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 40 40 40 40 50 40 50 50 50 50 50 60 60 60 60 80 80 100 100

1 -1/2 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 15 15 15 15 15 17 15 15 15 15 16 13 13 15 19 13 16 13 18

35 35 35 35 35 35 35 35 35 35 35 35 40 40 40 40 40 40 40 40 40 40 40 40 50 50 50 50 50 50 50 50 50 60 60 60 60 60 80 80 80 100 100 120

17 17 17 17 17 17 17 18 19 21 22 23 17 17 17 17 17 17 17 17 19 20 22 24 17 17 17 17 18 19 15 15 18 15 15 14 16 19 13 13 17 13 17 17

2 35 35 35 35 35 35 35 35 40 40 40 40 40 40 40 40 40 40 40 40 40 50 50 50 50 50 50 50 50 60 50 50 60 60 60 80 80 80 80 80 100 100 120 140

3 17 17 17 18 19 20 22 23 17 17 17 17 17 17 17 18 19 19 19 19 24 17 17 17 18 19 20 22 22 15 18 18 14 16 19 13 13 13 13 17 13 16 14 14

35 35 35 40 40 40 40 40 40 40 40 40 40 40 40 50 50 50 50 50 50 50 50 50 60 60 60 60 60 80 60 60 80 80 80 80 80 80 80 100 100 120 140 180

4 23 24 24 17 17 17 17 17 17 17 17 17 21 22 24 17 17 17 17 18 19 21 23 25 17 17 18 19 20 15 17 18 15 15 15 13 14 17 19 13 17 14 13 15

40 40 40 40 40 40 40 40 40 40 40 50 50 50 50 50 50 50 50 50 50 60 60 60 60 60 60 60 80 80 80 80 80 80 80 100 100 100 100 100 120 120 140 180

5 17 17 17 17 17 18 19 20 21 23 24 17 17 17 17 18 19 20 22 23 25 17 18 20 21 22 23 25 15 15 15 15 15 15 17 13 13 13 13 16 13 18 17 14

40 40 40 40 40 40 40 40 50 50 50 50 50 50 50 50 50 50 60 60 60 60 60 60 60 80 80 80 80 80 80 80 80 80 100 100 100 100 100 120 120 140 160 200

6 17 18 18 19 20 22 23 24 17 17 17 17 18 19 21 22 23 25 17 17 19 20 22 24 25 17 17 17 17 16 18 15 16 18 15 13 13 14 16 14 16 15 15 13

40 40 40 40 40 40 50 50 50 50 50 50 50 50 50 60 60 60 60 60 60 60 60 80 80 80 80 80 80 80 100 80 100 100 100 100 100 100 120 120 140 140 160 200

7 -1/2 20 21 22 23 24 25 17 17 17 18 19 20 22 23 24 17 17 18 19 20 22 24 26 17 17 17 17 17 18 19 15 16 15 15 15 14 16 18 13 15 13 17 18 15

40 40 50 50 50 50 50 50 50 50 50 50 60 60 60 60 60 60 60 80 80 80 80 80 80 80 80 80 80 100 100 100 100 100 100 100 120 120 120 120 140 160 180 240

24 25 17 17 17 17 18 19 21 22 24 25 17 17 18 20 21 22 23 17 17 17 17 17 17 18 19 20 22 15 15 15 15 15 16 17 13 14 14 18 16 15 18 13

Notes: 1. Apply Service Factor to obtain Design Horsepower. Select small sprocket based upon Design Horsepower and RPM on this chart.

3. To use this chart for double or triple strand chain, divide the design horsepower by the following factors: Double strand: 1.9, Triple strand: 2.9

Engineering

2. Sprocket selections are recommended minimum. Larger sizes may be selected if required to obtain desired ratio, etc.

FEATURES/BENEFITS PAGE PT12-2

SPECIFICATION PAGES PT12-

RELATE PRO UCTS PAGES PT12-40

PT12-30

ENGINEERING/TECHNICAL PAGES PT12-42


DYNA-SYNC

SELECTION Easy Selection Table RECOMMENDED SMALL SPROCKET Chain Size and No. of Teeth for Design HP

17 18 19 20 21 22 24 16 17 18 19 20 21 22 24 17 17 17 17 17 17 17 19 21 22 15 15 16 17 17 20 15 15 18 15 14 15 18 13 15 15 13 15 15

12 50 50 50 50 60 60 60 60 60 60 60 60 80 80 80 80 80 80 80 80 80 80 80 80 100 100 100 100 100 120 120 120 120 120 120 120 120 140 140 160 180 180 200 240

20 21 22 23 16 17 17 18 19 21 22 23 16 17 17 17 17 17 17 18 19 20 22 25 17 17 17 17 18 15 15 16 18 19 15 16 18 14 16 13 13 16 18 17

15 60 60 60 60 60 60 60 60 60 80 80 80 80 80 80 80 80 80 80 80 80 100 100 100 100 100 100 100 100 120 120 120 120 140 140 140 140 140 160 160 180 200 240 240

20

17 17 17 17 18 19 21 22 24 17 17 17 17 17 17 17 18 19 20 22 23 17 17 17 18 19 20 21 24 15 18 18 18 15 18 13 15 17 14 18 16 15 14 22

60 60 60 60 60 60 80 80 80 80 80 80 80 80 80 80 80 100 100 100 100 100 100 100 100 100 120 120 120 140 140 140 140 160 160 160 160 160 160 180 200 240 240 240

20 21 22 23 24 25 17 17 17 17 17 17 18 19 21 22 23 17 17 17 17 18 20 22 24 24 17 18 19 15 16 17 18 15 16 13 14 16 18 16 16 13 18 29

25

30

40

50

60

70

80

90

100

60 24 80 17 80 17 80 17 80 17 80 17 80 17 80 17 80 18 80 19 80 20 80 21 80 22 80 24 100 17 100 17 100 17 100 17 100 18 100 19 100 20 100 22 100 24 120 17 120 17 120 18 120 21 120 21 120 21 140 16 140 19 140 19 160 15 160 19 180 15 180 16 180 14 180 13 180 15 200 15 240 13 240 15 240 23 ....

80 17 80 17 80 17 80 17 80 17 80 17 80 18 80 19 80 21 80 22 80 23 100 17 100 17 100 17 100 17 100 18 100 19 100 20 100 21 100 22 100 24 120 17 120 18 120 21 120 21 140 16 140 17 140 17 140 18 140 19 160 16 160 17 160 18 180 15 180 18 200 15 200 16 180 15 180 18 200 17 240 13 240 21 .... ....

80 18 80 18 80 19 80 20 80 21 80 22 80 23 100 17 100 17 100 17 100 17 100 18 100 19 100 20 100 21 100 24 100 24 120 17 120 17 120 18 120 21 120 21 140 17 140 17 140 18 140 19 140 21 140 21 160 17 160 17 160 19 160 21 180 17 200 15 200 18 200 19 200 21 240 15 240 13 240 14 240 15 240 27 .... ....

100 17 100 17 100 17 100 18 100 20 100 21 100 22 120 17 120 17 120 18 120 19 120 21 120 21 120 21 140 17 140 17 140 17 140 19 140 21 160 19 160 19 160 19 160 19 160 21 180 16 180 19 200 15 200 17 200 19 240 15 240 15 240 17 240 19 240 21 240 18 240 24 .... .... ....

100 24 120 17 120 17 120 18 120 19 120 21 140 17 140 17 140 17 140 17 140 19 160 17 160 18 160 19 160 19 160 21 160 21 180 17 180 18 180 19 200 16 200 18 200 19 240 15 240 17 240 18 240 20 240 23 240 25 240 27 .... .... .... ....

120 17 120 18 120 21 120 21 140 17 140 17 140 17 140 18 140 19 140 21 160 17 160 17 160 18 160 21 160 21 180 17 180 18 180 19 180 21 200 17 200 18 200 21 240 15 240 17 240 19 240 20 240 23 240 26 .... .... .... .... .... ....

140 18 140 19 140 21 160 17 160 18 160 18 160 19 160 20 180 17 180 18 180 19 180 19 200 17 200 18 200 19 200 21 200 23 240 16 240 19 240 22 240 24 240 26 .... .... .... .... .... .... ....

140 21 140 21 160 17 160 17 160 18 160 20 180 17 180 18 180 19 180 20 200 16 200 18 200 19 200 20 200 21 240 15 240 18 240 19 240 21 240 25 .... .... .... .... .... .... .... .... ....

160 20 160 22 160 23 180 18 180 21 200 17 200 17 200 19 200 21 200 23 240 18 240 18 240 18 240 20 240 23 240 26 .... .... .... .... .... .... .... .... ....

4. Sprocket selections above the bold line are based upon ANSI horsepower ratings. Selections below the bold line are based upon the chain pull formula for slow speed drives.

FEATURES/BENEFITS PAGE PT12-2

HT Synchrous Belts

50 50 50 50 50 50 50 60 60 60 60 60 60 60 60 80 80 80 80 80 80 80 80 80 80 100 100 100 100 100 100 100 120 120 120 120 120 120 140 140 160 180 200 240

Sprockets

10 17 17 17 18 19 20 21 23 24 17 17 18 19 20 22 23 17 17 17 17 17 17 17 19 20 21 22 24 15 15 17 18 15 16 19 13 14 16 19 14 13 18 13 13

Conveyor Components

9 50 50 50 50 50 50 50 50 50 60 60 60 60 60 60 60 80 80 80 80 80 80 80 80 80 80 80 80 100 100 100 100 100 100 100 120 120 120 120 140 160 160 200 240

5. To achieve design life keep chain free of dirt and contaminants, and apply appropriate lubrication.

SPECIFICATION PAGES PT12-

Engineering

RPM of small Sprocket 951-1000 901-950 851-900 801-850 751-800 701-750 651-700 601-650 551-600 501-550 471-500 441-470 411-440 381-410 351-380 321-350 301-320 281-300 261-280 241-260 221-240 201-220 181-200 161-180 151-160 141-150 131-140 121-130 111-120 101-110 91-100 81-90 71-80 61-70 51-60 46-50 41-45 35-40 30-35 23-29 17-22 12-16 8-11 5-7

RELATE PRO UCTS PAGES PT12-40

PT12-31

ENGINEERING/TECHNICAL PAGES PT12-42


DYNA-SYNC

SELECTION Basic Horsepower Ratings 35

HT Synchrous Belts Sprockets

No. Teeth 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 28 30 32 35 40 45

41

Conveyor Components Engineering

No. Teeth 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 28 30 32 35 40 45

HORSEPOWER RATINGS

3/8” Pitch Single Strand Roller Chain 50 75 0.08 0.12 0.09 0.13 0.10 0.14 0.11 0.16 0.01 0.12 0.13 0.19 0.14 0.20 0.15 0.21 0.16 0.23 0.17 0.24 0.18 0.26 0.19 0.27 0.20 0.29 0.21 0.30 0.22 0.31 0.23 0.33 0.24 0.34 0.25 0.36 0.27 0.39 0.29 0.42 0.31 0.45 0.33 0.49 0.39 0.56 0.45 0.64 TYPE A

100 0.15 0.16 0.18 0.20 0.22 0.24 0.25 0.27 0.29 0.31 0.33 0.35 0.37 0.38 0.40 0.42 0.44 0.46 0.50 0.54 0.58 0.64 0.73 0.83

150 0.21 0.23 0.26 0.28 0.31 0.34 0.36 0.39 0.41 0.44 0.47 0.50 0.52 0.54 0.57 0.60 0.63 0.66 0.71 0.77 0.83 0.91 1.04 1.18

200 0.27 0.30 0.34 0.37 0.41 0.44 0.47 0.50 0.54 0.57 0.61 0.64 0.68 0.71 0.74 0.78 0.82 0.85 0.92 1.00 1.07 1.18 1.35 1.54

250 0.33 0.37 0.41 0.46 0.50 0.53 0.57 0.62 0.66 0.70 0.74 0.78 0.83 0.87 0.91 0.96 1.00 1.05 1.13 1.22 1.31 1.44 1.66 1.89

300 0.39 0.44 0.49 0.54 0.59 0.63 0.68 0.73 0.78 0.83 0.88 0.93 0.98 1.03 1.08 1.14 1.19 1.24 1.34 1.45 1.56 1.71 1.97 2.24

400 0.50 0.57 0.63 0.70 0.76 0.82 0.88 0.95 1.01 1.08 1.14 1.21 1.27 1.34 1.40 1.47 1.54 1.60 1.73 1.87 2.01 2.21 2.55 2.90

500 0.62 0.70 0.77 0.85 0.93 1.01 1.08 1.16 1.24 1.32 1.40 1.48 1.56 1.64 1.72 1.80 1.88 1.96 2.12 2.29 2.45 2.70 3.12 3.55

25 50 0.05 0.10 0.06 0.11 0.07 0.13 0.07 0.14 0.08 0.15 0.09 0.16 0.09 0.18 0.10 0.19 0.11 0.20 0.12 0.22 0.12 0.23 0.13 0.24 0.14 0.26 0.14 0.27 0.15 0.28 0.16 0.29 0.17 0.31 0.17 0.32 0.19 0.35 0.20 0.38 0.22 0.40 0.24 0.44 0.27 0.51 0.31 0.58 TYPE A

75 0.14 0.16 0.19 0.20 0.22 0.24 0.26 0.28 0.29 0.31 0.33 0.35 0.37 0.39 0.41 0.42 0.44 0.46 0.50 0.54 0.58 0.64 0.74 0.83

Lubrication Note TYPE A: Manual or Drip TYPE B: Bath or Disc TYPE C: Oil Stream

FEATURES/BENEFITS PAGE PT12-2

100 0.19 0.21 0.24 0.26 0.28 0.31 0.33 0.36 0.38 0.40 0.43 0.45 0.48 0.50 0.53 0.55 0.57 0.60 0.65 0.70 0.75 0.83 0.96 1.08

150 0.28 0.31 0.34 0.38 0.40 0.44 0.48 0.51 0.55 0.58 0.62 0.65 0.69 0.72 0.76 0.79 0.82 0.86 0.93 1.00 1.08 1.19 1.37 1.55

200 0.36 0.40 0.44 0.49 0.53 0.57 0.62 0.66 0.71 0.75 0.80 0.84 0.89 0.93 0.98 1.03 1.07 1.12 1.21 1.31 1.40 1.54 1.78 2.02

250 0.44 0.49 0.54 0.60 0.64 0.70 0.76 0.81 0.87 0.92 0.98 1.03 1.09 1.14 1.20 1.26 1.31 1.37 1.48 1.60 1.71 1.88 2.18 2.47

1000 1.21 1.28 1.51 1.66 1.81 1.96 2.11 2.26 2.42 2.57 2.70 2.88 3.03 3.19 3.35 3.51 3.66 3.82 4.14 4.46 4.79 5.23 6.09 6.91

1200 1.37 1.54 1.70 1.87 2.04 2.21 2.38 2.55 2.73 2.90 3.02 3.25 3.42 3.60 3.78 3.96 4.13 4.31 4.67 5.03 5.40 5.96 6.87 7.80

1500 1.68 1.88 2.08 2.29 2.49 2.70 2.91 3.12 3.33 3.45 3.76 3.97 4.19 4.40 4.62 4.84 5.05 5.27 5.71 6.15 6.60 7.27 8.40 9.53

1800 1.98 2.21 2.45 2.70 2.94 3.18 3.43 3.68 3.93 4.18 4.43 4.68 4.93 5.19 5.44 5.70 5.95 6.21 6.73 7.25 7.77 8.56 9.89 11.2

2100 2.27 2.54 2.82 3.10 3.38 3.66 3.94 4.22 4.51 4.80 5.09 5.38 5.67 5.96 6.25 6.55 6.84 7.13 7.73 8.33 8.93 9.84 11.4 12.9

2500 2.65 2.97 3.30 3.62 3.95 4.28 4.61 4.94 5.28 5.61 5.95 6.29 6.63 6.97 7.31 7.66 8.00 8.35 9.05 9.74 10.0 11.5 13.3 15.1

900 1.38 1.54 1.71 1.88 2.05 2.22 2.39 2.57 2.74 2.91 3.09 3.26 3.44 3.62 3.80 3.97 4.15 4.33 4.69 5.06 5.42 5.97 6.90 7.84

1000 1.52 1.70 1.88 2.07 2.25 2.44 2.63 2.82 3.01 3.20 3.40 3.59 3.78 3.98 4.17 4.37 4.57 4.76 5.16 5.56 5.96 6.57 7.59 8.62

1200 1.27 1.49 1.71 1.95 2.20 2.46 2.73 3.01 3.29 3.59 3.89 4.20 4.46 4.69 4.92 5.15 5.38 5.61 6.08 6.55 7.03 7.74 8.94 10.2

3000 3500 2.17 1.73 2.55 2.02 2.94 2.33 3.35 2.66 3.77 3.00 4.22 3.35 4.68 3.71 5.15 4.09 5.64 4.48 6.15 4.88 6.67 5.29 7.20 5.72 7.75 6.15 8.21 6.59 8.62 7.05 9.02 7.51 9.43 7.99 9.84 8.47 10.7 9.47 11.5 10.5 12.3 11.6 13.6 13.2 15.7 16.2 17.8 19.3 TYPE C

4000 1.41 1.65 1.91 2.17 2.45 2.74 3.04 3.35 3.67 3.99 4.33 4.68 5.03 5.40 5.77 6.15 6.54 6.93 7.75 8.59 9.47 10.8 13.2 15.8

HORSEPOWER RATINGS

1/2” Pitch Single Strand Roller Chain 10 0.02 0.03 0.03 0.03 0.03 0.03 0.04 0.04 0.05 0.05 0.05 0.06 0.06 0.06 0.06 0.07 0.07 0.07 0.08 0.08 0.09 0.10 0.12 0.14

Small Sprocket RPM 600 700 800 900 0.73 0.84 0.95 1.06 0.82 0.95 0.98 1.02 0.91 1.05 1.18 1.31 1.00 1.15 1.30 1.44 1.10 1.26 1.42 1.57 1.19 1.36 1.54 1.71 1.28 1.47 1.66 1.84 1.37 1.57 1.77 1.97 1.46 1.68 1.89 2.10 1.55 1.78 2.01 2.24 1.65 1.89 2.13 2.37 1.74 2.00 2.26 2.51 1.84 2.11 2.38 2.64 1.93 2.22 2.50 2.78 2.03 2.33 2.63 2.92 2.12 2.44 2.75 3.05 2.21 2.55 2.87 3.19 2.31 2.66 3.00 3.33 2.50 2.88 3.25 3.61 2.70 3.10 3.50 3.89 2.88 3.32 3.75 4.17 3.18 3.66 4.08 4.50 3.68 4.23 4.77 5.30 4.18 4.80 5.41 6.02 TYPE B

300 0.51 0.57 0.64 0.70 0.76 0.83 0.89 0.95 1.02 1.08 1.15 1.21 1.28 1.35 1.41 1.48 1.55 1.61 1.75 1.88 2.02 2.22 2.57 2.92

Small Sprocket RPM 350 400 450 500 0.59 0.66 0.74 0.81 0.66 0.74 0.83 0.91 0.73 0.82 0.92 1.01 0.81 0.91 1.01 1.11 0.88 0.99 1.10 1.21 0.95 1.07 1.19 1.31 1.02 1.15 1.28 1.41 1.10 1.24 1.38 1.51 1.17 1.32 1.47 1.61 1.24 1.40 1.56 1.72 1.32 1.49 1.65 1.82 1.39 1.57 1.75 1.92 1.47 1.66 1.85 2.03 1.55 1.74 1.94 2.13 1.62 1.83 2.04 2.24 1.70 1.92 2.13 2.34 1.77 2.00 2.23 2.45 1.85 2.09 2.32 2.55 2.01 2.26 2.52 2.77 2.16 2.44 2.71 2.98 2.32 2.61 2.91 3.20 2.55 2.88 3.20 3.52 2.95 3.33 3.70 4.07 3.35 3.78 4.20 4.62 TYPE B

600 0.96 1.07 1.19 1.31 1.42 1.54 1.66 1.78 1.89 2.02 2.14 2.26 2.39 2.51 2.64 2.76 2.88 3.01 3.26 3.51 3.77 4.14 4.79 5.44

700 1.10 1.23 1.37 1.50 1.63 1.77 1.91 2.05 2.18 2.32 2.46 2.60 2.74 2.89 3.03 3.17 3.31 3.46 3.74 4.03 4.33 4.76 5.50 6.25

800 1.24 1.39 1.54 1.69 1.84 2.00 2.15 2.31 2.46 2.62 2.78 2.93 3.09 3.26 3.42 3.57 3.73 3.90 4.22 4.55 4.88 5.37 6.20 7.05

1400 1.01 1.18 1.36 1.55 1.75 1.95 2.17 2.39 2.61 2.85 3.09 3.33 3.59 3.85 4.11 4.38 4.66 4.94 5.52 6.13 6.75 7.72 9.43 11.3

1600 1800 0.82 0.69 0.96 0.81 1.11 0.93 1.27 1.06 1.43 1.20 1.60 1.34 1.77 1.49 1.95 1.64 2.14 1.79 2.33 1.95 2.53 2.12 2.73 2.29 2.94 2.46 3.15 2.64 3.37 2.82 3.59 3.01 3.81 3.20 4.05 3.39 4.52 3.79 5.01 4.20 5.52 4.63 6.32 5.29 7.72 6.47 9.21 7.72 TYPE C

Multiple Strand Chain HP Factors: Single Strand 1.0 Double Strand 1.9 Triple Strand 2.8

SPECIFICATION PAGES PT12-

RELATE PRO UCTS PAGES PT12-40

PT12-32

ENGINEERING/TECHNICAL PAGES PT12-42


50 No. Teeth 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 28 30 32 35 40 45

HORSEPOWER RATINGS

1/2” Pitch Single Strand Roller Chain 10 0.04 0.05 0.05 0.06 0.06 0.07 0.07 0.08 0.09 0.09 0.10 0.11 0.11 0.12 0.13 0.13 0.14 0.15 0.16 0.16 0.17 0.19 0.22 0.25

25 50 0.10 0.19 0.11 0.21 0.12 0.23 0.14 0.25 0.15 0.28 0.16 0.30 0.17 0.32 0.19 0.35 0.20 0.37 0.21 0.39 0.22 0.42 0.24 0.44 0.25 0.46 0.26 0.49 0.27 0.51 0.29 0.54 0.30 0.56 0.31 0.58 0.34 0.63 0.37 0.68 0.39 0.73 0.43 0.81 0.50 0.93 0.57 1.06 TYPE A

75 0.27 0.30 0.33 0.36 0.40 0.43 0.46 0.50 0.53 0.56 0.60 0.63 0.67 0.70 0.74 0.77 0.80 0.84 0.91 0.98 1.05 1.16 1.34 1.52

100 0.35 0.38 0.43 0.47 0.52 0.56 0.60 0.65 0.69 0.73 0.78 0.82 0.87 0.91 0.96 1.00 1.05 1.09 1.18 1.27 1.36 1.50 1.74 1.97

150 0.50 0.56 0.62 0.68 0.74 0.80 0.86 0.93 0.99 1.05 1.12 1.17 1.25 1.31 1.37 1.43 1.50 1.57 1.69 1.83 1.96 2.16 2.49 2.83

200 0.65 0.73 0.80 0.88 0.96 1.04 1.12 1.20 1.29 1.37 1.45 1.53 1.62 1.70 1.78 1.87 1.95 2.04 2.20 2.38 2.55 2.81 3.24 3.68

250 0.79 0.89 0.98 1.08 1.17 1.27 1.37 1.47 1.57 1.66 1.77 1.87 1.98 2.08 2.18 2.28 2.38 2.49 2.69 2.90 3.11 3.43 3.95 4.49

300 0.93 1.04 1.16 1.27 1.39 1.50 1.62 1.74 1.85 1.95 2.09 2.21 2.33 2.45 2.57 2.69 2.81 2.93 3.18 3.42 3.67 4.04 4.67 5.30

Small Sprocket RPM 350 400 450 500 600 1.07 1.21 1.35 1.48 1.74 1.20 1.35 1.50 1.65 1.95 1.33 1.50 1.67 1.83 2.16 1.46 1.65 1.83 2.01 2.37 1.60 1.80 2.00 2.20 2.59 1.73 1.95 2.16 2.38 2.80 1.86 2.10 2.33 2.56 3.02 2.00 2.25 2.50 2.75 3.24 2.13 2.40 2.67 2.93 3.45 2.25 2.55 2.84 3.12 3.67 2.40 2.71 3.01 3.31 3.90 2.54 2.86 3.18 3.50 4.12 2.68 3.02 3.36 3.69 4.34 2.81 3.17 3.53 3.88 4.57 2.95 3.33 3.70 4.07 4.79 3.09 3.48 3.87 4.26 5.01 3.22 3.64 4.05 4.45 5.24 3.37 3.80 4.22 4.64 5.46 3.64 4.11 4.57 5.03 5.92 3.93 4.43 4.93 5.42 6.38 4.21 4.75 5.28 5.81 6.84 4.64 5.24 5.82 6.40 7.53 5.36 6.05 6.72 7.39 8.70 6.09 6.87 7.64 8.40 9.90 TYPE B

300 1.81 2.03 2.25 2.47 2.70 2.92 3.15 3.38 3.61 3.83 4.07 4.30 4.53 4.76 5.00 5.23 5.47 5.70 6.18 6.66 7.14 7.86 9.1 10.3

Small Sprocket RPM 350 400 450 500 2.08 2.35 2.61 2.87 2.33 2.63 2.93 3.22 2.59 2.92 3.25 3.57 2.84 3.21 3.57 3.92 3.10 3.50 3.89 4.27 3.36 3.79 4.21 4.63 3.62 4.08 4.54 4.99 3.88 4.37 4.86 5.35 4.14 4.67 5.19 5.71 4.40 4.97 5.52 6.07 4.67 5.27 5.86 6.44 4.94 5.57 6.19 6.80 5.20 5.87 6.52 7.17 5.47 6.17 6.86 7.54 5.74 6.47 7.19 7.91 6.01 6.78 7.54 8.29 6.28 7.08 7.87 8.66 6.55 7.39 8.21 9.03 7.10 8.01 8.90 9.79 7.65 8.6 9.6 10.5 8.20 9.3 10.3 11.3 9.03 10.2 11.4 12.5 10.4 11.8 13.1 14.4 11.9 13.4 14.9 16.3 TYPE B

25 50 0.19 0.36 0.22 0.41 0.24 0.45 0.26 0.49 0.29 0.54 0.31 0.58 0.34 0.63 0.36 0.67 0.39 0.72 0.41 0.76 0.43 0.81 0.46 0.86 0.48 0.90 0.51 0.95 0.53 1.00 0.56 1.04 0.58 1.09 0.61 1.14 0.66 1.23 0.71 1.33 0.76 1.42 0.84 1.57 0.97 1.81 1.10 2.06 TYPE A

75 0.52 0.58 0.65 0.71 0.77 0.84 0.90 0.97 1.03 1.10 1.16 1.23 1.30 1.36 1.43 1.50 1.56 1.63 1.77 1.90 2.04 2.25 2.60 2.95

Lubrication Note TYPE A: Manual or Drip TYPE B: Bath or Disc TYPE C: Oil Stream FEATURES/BENEFITS PAGE PT12-2

100 0.67 0.76 0.84 0.92 1.00 1.09 1.17 1.26 1.34 1.43 1.51 1.60 1.69 1.77 1.86 1.95 2.03 2.12 2.30 2.48 2.66 2.93 3.38 3.84

150 0.97 1.09 1.20 1.32 1.44 1.56 1.68 1.80 1.92 2.05 2.15 2.29 2.42 2.54 2.67 2.79 2.92 3.04 3.30 3.55 3.81 4.20 4.85 5.50

200 1.26 1.41 1.56 1.72 1.87 2.03 2.19 2.34 2.50 2.66 2.82 2.98 3.14 3.31 3.47 3.63 3.80 3.96 4.29 4.62 4.96 5.46 6.31 7.16

250 1.53 1.72 1.91 2.10 2.29 2.48 2.67 2.86 3.06 3.25 3.45 3.64 3.84 4.03 4.24 4.43 4.64 4.83 5.24 5.64 6.05 6.66 7.70 8.73

800 2.26 2.53 2.80 3.08 3.35 3.63 3.91 4.19 4.48 4.76 5.05 5.34 5.63 5.92 6.21 6.5 6.8 7.1 7.7 8.3 8.9 9.8 11.3 12.8

900 2.51 2.81 3.11 3.42 3.73 4.04 4.35 4.66 4.98 5.30 5.62 5.94 6.26 6.58 6.90 7.2 7.6 7.9 8.5 9.2 9.9 10.9 12.5 14.2

1000 2.75 3.09 3.42 3.76 4.10 4.44 4.78 5.13 5.48 5.82 6.17 6.53 6.88 7.23 7.59 8.0 8.3 8.7 9.4 10.1 10.8 11.9 13.8 15.7

1200 3.25 3.64 4.03 4.43 4.83 5.23 5.64 6.04 6.45 6.86 7.27 7.69 8.11 8.52 8.94 9.4 9.8 10.2 11.1 11.9 12.8 14.1 16.3 18.5

1400 3.73 4.18 4.63 5.09 5.55 6.01 6.47 6.94 7.41 7.88 8.4 8.8 9.3 9.8 10.3 10.8 11.2 11.7 12.7 13.7 14.7 16.2 18.7 21.2

900 4.88 5.46 6.06 6.65 7.25 7.86 8.47 9.08 9.69 10.3 10.9 11.5 12.2 12.8 13.4 14.1 14.7 15.3 16.6 17.9 19.2 21.1 24.4 27.7

1000 5.36 6.01 6.66 7.31 8.0 8.6 9.3 10.0 10.7 11.3 12.0 12.7 13.4 14.1 14.8 15.5 16.2 16.9 18.3 19.7 21.1 23.2 26.8 30.5

1200 1400 6.32 6.02 7.08 7.05 7.85 8.13 8.62 9.26 9.4 10.4 10.2 11.7 11.0 12.6 11.8 13.5 12.6 14.4 13.4 15.3 14.2 16.3 15.0 17.2 15.8 18.1 16.6 19.1 17.4 20.0 18.2 20.9 19.0 21.9 19.9 22.8 21.5 24.7 23.2 26.6 24.9 28.6 27.4 31.5 31.6 36.3 35.9 41.3 TYPE C

1600 1800 4.12 3.45 4.71 4.04 5.22 4.66 5.74 5.31 6.26 5.99 6.78 6.70 7.30 7.43 7.83 8.18 8.36 8.96 8.89 9.76 9.4 10.5 10.0 11.1 10.5 11.7 11.0 12.3 11.6 12.9 12.1 13.5 12.7 14.1 13.2 14.7 14.3 15.9 15.4 17.2 16.5 18.4 18.2 20.3 21.1 23.4 23.9 26.6 TYPE C

HORSEPOWER RATINGS

5/8” Pitch Single Strand Roller Chain 10 0.09 0.10 0.11 0.12 0.13 0.14 0.15 0.16 0.17 0.18 0.19 0.20 0.21 0.22 0.23 0.25 0.26 0.27 0.29 0.31 0.33 0.37 0.43 0.48

700 2.00 2.24 2.48 2.73 2.97 3.22 3.47 3.72 3.97 4.22 4.48 4.73 4.99 5.25 5.51 5.8 6.0 6.3 6.8 7.3 7.9 8.7 10.0 11.4

600 3.38 3.79 4.20 4.62 5.03 5.45 5.87 6.30 6.72 7.15 7.58 8.01 8.44 8.9 9.3 9.7 10.2 10.6 11.5 12.4 13.3 14.7 17.0 19.2

700 3.89 4.36 4.83 5.31 5.78 6.27 6.75 7.24 7.73 8.22 8.72 9.21 9.71 10.2 10.7 11.2 11.7 12.2 13.2 14.3 15.3 16.9 19.5 22.1

800 4.39 4.91 5.45 5.98 6.52 7.07 7.61 8.16 8.71 9.3 9.8 10.4 11.0 11.5 12.0 12.7 13.2 13.8 14.9 16.1 17.3 19.0 22.0 24.9

1600 4.92 5.77 6.65 7.58 8.6 9.6 10.6 11.7 12.8 13.9 15.1 16.3 17.6 18.8 20.1 21.4 22.8 24.2 27.0 30.0 32.2 35.5 41.0 46.5

1800 4.13 4.83 5.58 6.35 7.2 8.0 8.9 9.8 10.7 11.7 12.7 13.7 14.7 15.8 16.9 18.0 19.1 20.3 22.6 25.1 27.7 31.6 38.7 46.1

Multiple Strand Chain HP Factors: Single Strand 1.0 Double Strand 1.9 Triple Strand 2.8 SPECIFICATION PAGES PT12-

RELATE PRO UCTS PAGES PT12-40

PT12-33

ENGINEERING/TECHNICAL PAGES PT12-42

Sprockets

No. Teeth 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 28 30 32 35 40 45

Conveyor Components

40

Engineering

Basic Horsepower Ratings

HT Synchrous Belts

DYNA-SYNC

SELECTION


DYNA-SYNC

SELECTION Basic Horsepower Ratings 60

HT Synchrous Belts Sprockets

No. Teeth 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 28 30 32 35 40 45

80

HORSEPOWER RATINGS

3/4” Pitch Single Strand Roller Chain 10 25 0.15 0.33 0.16 0.37 0.18 0.41 0.20 0.45 0.22 0.50 0.24 0.54 0.25 0.58 0.27 0.62 0.29 0.66 0.31 0.70 0.33 0.75 0.35 0.79 0.36 0.83 0.38 0.87 0.40 0.92 0.42 0.96 0.44 1.00 0.46 1.05 0.50 1.13 0.54 1.22 0.57 1.31 0.63 1.44 0.73 1.67 0.83 1.89 TYPE A

50 0.62 0.70 0.77 0.85 0.92 1.00 1.08 1.16 1.24 1.31 1.39 1.47 1.55 1.63 1.71 1.79 1.87 1.95 2.12 2.28 2.45 2.69 3.11 3.53

75 0.89 1.00 1.11 1.22 1.33 1.44 1.55 1.66 1.78 1.88 2.00 2.11 2.23 2.34 2.45 2.57 2.68 2.80 3.04 3.27 3.51 3.86 4.46 5.07

100 1.16 1.30 1.44 1.58 1.73 1.87 2.01 2.16 2.31 2.45 2.60 2.75 2.90 3.05 3.19 3.35 3.50 3.65 3.95 4.26 4.56 5.03 5.81 6.60

125 1.42 1.59 1.76 1.93 2.11 2.28 2.46 2.64 2.82 2.99 3.17 3.36 3.54 3.72 3.90 4.09 4.27 4.45 4.82 5.20 5.57 6.14 7.09 8.05

150 1.67 1.87 2.07 2.28 2.49 2.69 2.90 3.11 3.32 3.53 3.74 3.96 4.17 4.39 4.60 4.82 5.04 5.25 5.69 6.13 6.57 7.24 8.37 9.50

175 1.91 2.15 2.38 2.62 2.86 3.09 3.33 3.57 3.81 4.05 4.30 4.55 4.79 5.04 5.28 5.53 5.78 6.03 6.53 7.04 7.55 8.31 9.59 10.9

Small Sprocket RPM 200 250 300 350 400 2.16 2.64 3.12 3.58 4.04 2.43 2.96 3.49 4.01 4.53 2.69 3.28 3.87 4.44 5.02 2.95 3.60 4.25 4.88 5.51 3.22 3.93 4.64 5.33 6.01 3.49 4.26 5.02 5.77 6.51 3.76 4.59 5.41 6.21 7.01 4.03 4.92 5.80 6.66 7.52 4.30 5.25 6.20 7.12 8.03 4.58 5.59 6.59 7.57 8.54 4.85 5.92 6.99 8.02 9.05 5.13 6.26 7.38 8.48 9.57 5.40 6.59 7.78 8.94 10.1 5.68 6.94 8.19 9.40 10.6 5.96 7.28 8.59 9.85 11.1 6.24 7.62 8.99 10.3 11.6 6.52 7.96 9.40 10.8 12.2 6.81 8.31 9.80 11.3 12.7 7.37 8.99 10.6 12.2 13.8 7.94 9.67 11.4 13.1 14.8 8.52 10.4 12.3 14.1 15.9 9.38 11.4 13.5 15.5 17.5 10.8 13.2 15.6 17.9 20.2 12.3 15.0 17.7 20.4 23.0 TYPE B

Conveyor Components Engineering

25 0.78 0.87 0.97 1.06 1.16 1.25 1.35 1.45 1.55 1.64 1.74 1.84 1.94 2.04 2.14 2.24 2.34 2.45 2.65 2.85 3.06 3.37 3.89 4.42

50 1.45 1.63 1.80 1.98 2.16 2.34 2.52 2.70 2.88 3.07 3.25 3.44 3.62 3.81 4.00 4.19 4.37 4.56 4.94 5.33 5.71 6.29 7.27 8.25

75 2.08 2.33 2.58 2.84 3.10 3.35 3.61 3.87 4.13 4.40 4.66 4.93 5.19 5.46 5.73 6.00 6.27 6.54 7.09 7.64 8.21 9.00 10.4 11.8

Lubrication Note TYPE A: Manual or Drip TYPE B: Bath or Disc TYPE C: Oil Stream

FEATURES/BENEFITS PAGE PT12-2

100 2.71 3.03 3.36 3.69 4.03 4.36 4.70 5.04 5.38 5.72 6.07 6.41 6.76 7.11 7.46 7.81 8.16 8.52 9.23 9.94 10.7 11.7 13.6 15.4

125 3.31 3.70 4.10 4.51 4.91 5.33 5.74 6.15 6.57 6.99 7.41 7.83 8.25 8.66 9.08 9.56 9.98 10.4 11.3 12.1 13.0 14.3 16.5 18.8

150 3.90 4.37 4.84 5.32 5.80 6.29 6.77 7.26 7.75 8.25 8.74 9.24 9.74 10.2 10.7 11.3 11.8 12.3 13.3 14.3 15.3 16.9 19.5 22.2

600 5.82 6.52 7.23 7.94 8.65 9.37 10.1 10.8 11.6 12.3 13.0 13.8 14.5 15.3 16.0 16.8 17.5 18.3 19.8 21.4 22.9 25.2 29.1 33.1

700 6.68 7.49 8.30 9.12 9.94 10.8 11.6 12.4 13.3 14.1 15.0 15.8 16.7 17.5 18.4 19.3 20.1 21.0 22.8 24.5 26.3 29.0 33.5 38.0

800 7.54 8.44 9.36 10.3 11.2 12.1 13.1 14.0 15.0 15.9 16.9 17.9 18.8 19.8 20.8 21.7 22.7 23.7 25.7 27.7 29.7 32.7 37.7 42.9

900 8.38 9.39 10.4 11.4 12.5 13.5 14.5 15.6 16.7 17.7 18.8 19.8 20.9 22.0 23.1 24.2 25.3 26.4 28.5 30.8 33.0 36.3 42.0 47.7

1000 1200 9.21 8.77 10.3 10.3 11.4 11.9 12.6 13.5 13.7 15.2 14.8 17.0 16.0 18.8 17.1 20.2 18.3 21.6 19.5 22.9 20.6 24.3 21.8 25.7 23.0 27.1 24.2 28.5 25.4 29.9 26.6 31.3 27.8 32.7 29.0 34.1 31.4 37.0 33.8 39.8 36.3 42.7 39.9 47.1 46.1 54.4 52.4 61.7 TYPE C

1400 6.96 8.15 9.4 10.7 12.1 13.5 15.0 16.5 18.1 19.7 21.4 23.1 24.8 26.6 28.4 30.3 32.2 34.2 38.2 42.4 46.7 53.4 62.5 70.9

1600 5.70 6.67 7.70 8.77 9.89 11.1 12.3 13.5 14.8 16.1 17.5 18.9 20.3 21.8 23.3 24.8 26.4 28.0 31.3 34.7 38.2 43.7 53.4 63.7

1400 8.76 10.3 11.8 13.5 15.2 17.0 18.9 20.8 22.7 24.8 26.9 29.0 31.2 33.5 35.8 38.2 40.6 43.0 48.1 53.3 58.7 67.2 82.1 98.0

1600 7.17 8.40 9.69 11.0 12.5 13.9 15.4 17.0 18.6 20.3 22.0 23.8 25.6 27.4 29.3 31.2 33.2 35.2 39.4 43.6 48.1 55.0 67.2 80.2

HORSEPOWER RATINGS

1” Pitch Single Strand Roller Chain

No. Teeth 10 9 0.34 10 0.38 11 0.42 12 0.47 13 0.51 14 0.55 15 0.59 16 0.63 17 0.68 18 0.72 19 0.76 20 0.81 21 0.85 22 0.90 23 0.94 24 0.98 25 1.03 26 1.07 28 1.16 30 1.25 32 1.34 35 1.48 40 1.71 45 1.94 TYPE A

500 4.94 5.53 6.13 6.74 7.34 7.96 8.57 9.19 9.81 10.4 11.1 11.7 12.3 13.0 13.6 14.2 14.9 15.5 16.8 18.1 19.4 21.4 24.7 28.1

175 200 4.48 5.05 5.02 5.66 5.56 6.28 6.11 6.89 6.66 7.52 7.22 8.14 7.77 8.77 8.34 9.41 8.88 10.0 9.48 10.7 10.0 11.3 10.6 12.0 11.2 12.6 11.8 13.3 12.3 13.9 13.0 14.6 13.5 15.2 14.1 15.9 15.3 17.2 16.4 18.5 17.6 19.9 19.4 21.9 22.4 25.3 25.5 28.7 TYPE B

Small Sprocket RPM 250 300 350 400 6.17 7.28 8.36 9.43 6.91 8.16 9.38 10.6 7.66 9.04 10.4 11.7 8.41 9.93 11.4 12.9 9.16 10.8 12.4 14.0 9.92 11.7 13.4 15.2 10.7 12.6 14.5 16.4 11.5 13.5 15.6 17.6 12.3 14.5 16.6 18.7 13.1 15.4 17.6 19.9 13.8 16.3 18.7 21.1 14.6 17.2 19.7 22.3 15.4 18.2 20.9 23.5 16.2 19.1 22.0 24.8 17.0 20.1 23.1 26.0 17.8 21.0 24.1 27.2 18.6 21.9 25.2 28.4 19.4 22.9 26.3 29.7 21.0 24.8 28.5 32.1 22.6 26.7 30.7 34.6 24.3 28.6 32.9 37.1 26.8 31.6 36.3 40.9 30.9 36.4 41.8 47.2 35.1 41.4 47.5 53.6

500 11.5 12.9 14.3 15.7 17.1 18.6 20.0 21.5 22.9 24.4 25.8 27.3 28.8 30.3 31.8 33.2 34.7 36.2 39.3 42.3 45.4 50.0 57.7 65.6

600 13.6 15.2 16.9 18.5 20.2 21.9 23.6 25.3 27.0 28.7 30.4 32.2 33.9 35.7 37.4 39.2 40.9 42.7 46.3 49.9 53.5 58.9 68.0 77.2

700 15.6 17.5 19.4 21.3 23.2 25.1 27.1 29.0 31.0 33.0 35.0 37.0 39.0 41.0 43.0 45.0 47.0 49.1 53.2 57.3 61.4 67.6 78.1 88.7

800 17.6 19.7 21.9 24.0 26.2 28.4 30.6 32.8 35.0 37.2 39.4 41.7 43.9 46.2 48.5 50.8 53.0 55.3 59.9 64.6 69.2 76.3 88.1 100

900 1000 17.0 14.5 19.9 17.0 23.0 19.6 26.2 22.3 29.1 25.2 31.5 28.2 34.0 31.2 36.4 34.4 38.9 37.7 41.4 41.1 43.8 44.5 46.3 48.1 48.9 51.7 51.4 55.5 53.9 59.3 56.4 62.0 59.0 64.8 61.5 67.6 66.7 73.7 71.8 78.9 77.0 84.6 84.8 93.3 99.0 108 111 122 TYPE C

1200 11.0 12.9 14.9 17.0 19.2 21.4 23.8 26.2 28.7 31.2 33.9 36.6 39.4 42.2 45.1 48.1 51.1 54.2 60.6 67.2 74.0 84.7 103 123

Multiple Strand Chain HP Factors: Single Strand 1.0 Double Strand 1.9 Triple Strand 2.8

SPECIFICATION PAGES PT12-

RELATE PRO UCTS PAGES PT12-40

PT12-34

ENGINEERING/TECHNICAL PAGES PT12-42


25 1.49 1.67 1.85 2.03 2.22 2.40 2.59 2.77 2.96 3.15 3.34 3.53 3.72 3.91 4.10 4.30 4.49 4.68 5.07 5.47 5.86 6.46 7.46 8.47

50 2.78 3.11 3.45 3.79 4.13 4.48 4.83 5.17 5.52 5.88 6.23 6.58 6.94 7.30 7.66 8.02 8.38 8.74 9.47 10.2 10.9 12.0 13.9 15.8

75 3.985 4.46 4.945 5.435 5.925 6.42 6.92 7.415 7.91 8.44 8.915 9.44 9.97 10.45 11.0 11.5 12.0 12.5 13.6 14.6 15.6 17.3 20.0 22.6

100 5.19 5.81 6.44 7.08 7.72 8.36 9.01 9.66 10.3 11.0 11.6 12.3 13.0 13.6 14.3 15.0 15.6 16.3 17.7 19.0 20.4 22.5 26.0 29.5

125 150 6.33 7.47 7.09 8.37 7.86 9.28 8.64 10.2 9.41 11.1 10.18 12.0 11.0 13.0 11.8 13.9 12.6 14.8 13.4 15.8 14.2 16.7 15.0 17.7 15.9 18.7 16.6 19.6 17.5 20.6 18.3 21.5 19.0 22.5 19.9 23.5 21.6 25.5 23.2 27.4 24.9 29.4 27.5 32.4 31.7 37.4 36.0 42.5 TYPE B

175 8.575 9.585 10.6 11.7 12.8 13.8 14.9 15.9 17.0 18.1 19.2 20.3 21.5 22.5 23.7 24.7 25.9 27.0 29.3 31.5 33.8 37.2 43.0 48.8

HORSEPOWER RATINGS 200 9.68 10.8 12.0 13.2 14.4 15.6 16.8 18.0 19.2 20.5 21.7 22.9 24.2 25.4 26.7 27.9 29.2 30.4 33.0 35.5 38.1 42.0 48.5 55.0

Small Sprocket RPM 250 300 350 400 11.8 13.9 16.0 18.1 13.2 15.6 17.9 20.2 14.6 17.3 19.8 22.4 16.1 19.0 21.8 24.6 17.5 20.7 23.8 26.9 19.0 22.5 25.8 29.1 20.5 24.2 27.8 31.4 22.0 26.0 29.8 33.6 23.5 27.7 31.8 35.9 25.0 29.5 33.8 38.2 26.5 31.2 35.8 40.5 28.0 33.0 37.9 42.8 29.5 34.8 39.9 45.1 31.0 36.6 42.0 47.4 32.6 38.4 44.1 49.8 34.0 40.2 46.2 52.1 35.6 42.0 48.2 54.4 37.1 43.8 50.3 56.8 40.3 47.5 54.5 61.5 43.3 51.2 58.8 66.3 46.5 54.9 63.0 71.1 51.2 60.4 69.4 78.3 59.2 69.8 80.1 90.4 67.2 79.3 91.2 103

200 16.3 18.3 20.3 22.3 24.3 26.3 28.4 30.4 32.5 34.6 36.6 38.7 40.8 42.9 45.0 47.1 49.3 51.4 55.7 60.0 64.3 70.9 81.8 92.9

Small Sprocket RPM 250 300 350 400 19.9 23.5 27.0 30.5 22.3 26.4 30.3 34.2 24.8 29.2 33.6 37.9 27.2 32.1 36.8 41.6 29.6 35.0 40.2 45.4 32.1 37.9 43.5 49.1 34.7 40.9 47.0 53.0 37.1 43.8 50.3 56.8 39.7 46.8 53.7 60.6 42.2 49.8 57.2 64.5 44.7 52.8 60.6 68.4 47.3 55.8 64.0 72.2 49.8 58.8 67.5 76.2 52.3 61.8 70.9 80.1 55.0 64.9 74.4 84.0 57.5 67.9 77.9 88.0 60.2 71.0 81.4 91.9 62.7 74.0 84.9 95.9 67.9 80.2 92.1 104 73.2 86.4 99.2 112 78.4 92.6 106.3 120 86.4 102 117 132 99.9 118 135.5 153 113 134 153.5 173

120 1-1/2” Pitch Single Strand Roller Chain No. Teeth 10 9 1.10 10 1.24 11 1.37 12 1.50 13 1.64 14 1.78 15 1.91 16 2.05 17 2.19 18 2.33 19 2.47 20 2.61 21 2.75 22 2.90 23 3.04 24 3.18 25 3.32 26 3.47 28 3.76 30 4.05 32 4.34 35 4.78 40 5.52 45 6.27 TYPE A

25 2.52 2.82 3.12 3.43 3.74 4.05 4.37 4.68 5.00 5.32 5.64 5.96 6.28 6.60 6.93 7.25 7.58 7.91 8.57 9.23 9.90 10.9 12.6 14.3

50 4.69 5.26 5.83 6.40 6.98 7.56 8.15 8.74 9.33 9.92 10.5 11.1 11.7 12.3 12.9 13.5 14.1 14.8 16.0 17.2 18.5 20.3 23.5 26.7

75 6.73 7.54 8.36 9.15 10.0 10.8 11.7 12.5 13.4 14.2 15.1 15.9 16.8 17.6 18.5 19.4 20.3 21.1 22.9 24.6 26.5 29.1 33.7 38.3

Lubrication Note TYPE A: Manual or Drip TYPE B: Bath or Disc TYPE C: Oil Stream FEATURES/BENEFITS PAGE PT12-2

100 8.76 9.81 10.9 11.9 13.0 14.1 15.2 16.3 17.4 18.5 19.6 20.7 21.9 23.0 24.1 25.3 26.4 27.5 29.8 32.1 34.5 38.0 43.9 49.8

125 150 10.7 12.6 12.0 14.1 13.3 15.7 14.6 17.2 15.9 18.8 17.2 20.3 18.5 21.9 19.9 23.5 21.3 25.1 22.6 26.7 24.0 28.3 25.3 29.9 26.7 31.5 28.0 33.1 29.5 34.8 30.9 36.4 32.2 38.0 33.6 39.7 36.4 43.0 39.2 46.3 42.0 49.6 46.3 54.7 53.6 63.2 60.8 71.7 TYPE B

175 14.4 16.2 18.0 19.7 21.5 23.3 25.1 27.0 28.8 30.6 32.4 34.3 36.2 38.0 39.9 41.8 43.7 45.6 49.3 53.2 57.0 62.8 72.5 82.3

450 20.1 22.5 24.9 27.4 29.8 32.3 34.8 37.3 39.9 42.5 45.0 47.5 50.1 52.7 55.3 57.9 60.5 63.1 68.3 73.7 79.0 87.0 101 114

500 22.1 24.7 27.4 30.1 32.8 35.6 38.3 41.1 43.9 46.7 49.5 52.3 55.1 58.0 60.8 63.7 66.6 69.4 75.2 81.0 86.9 95.7 111 126

600 700 26.0 29.6 29.2 33.5 32.3 37.1 35.5 40.8 38.7 44.5 41.9 48.2 45.2 51.9 48.4 55.6 51.7 59.4 55.0 63.2 58.3 67.0 61.6 70.8 65.0 74.6 68.3 78.5 71.7 82.3 75.0 86.2 78.4 90.1 81.8 94.0 88.6 102 95.5 110 102 118 113 130 130 150 148 170 TYPE C

800 24.2 28.4 32.8 37.3 42.1 47.0 52.2 57.5 63.0 68.6 74.4 79.8 84.2 88.5 92.8 97.2 102 106 115 124 133 146 169 192

900 20.3 23.8 27.5 31.3 35.3 39.4 43.7 48.2 52.8 57.5 62.3 67.3 72.4 77.7 83.0 88.5 94.1 99.8 112 124 136 156 188 213

1000 17.4 20.3 23.4 26.7 30.1 33.7 37.3 41.1 45.0 49.1 53.2 57.5 61.8 66.3 70.9 75.6 80.3 85.2 95.2 106 116 133 163 194

1100 15.0 17.6 20.3 23.2 26.1 29.2 32.4 35.7 39.0 42.5 46.1 49.8 53.6 57.5 61.4 65.5 69.6 73.8 82.5 91.5 101 115 141 168

1200 13.2 15.5 17.8 20.3 22.9 25.6 28.4 31.3 34.3 37.3 40.5 43.7 47.0 50.4 53.9 57.5 61.1 64.8 72.4 80.3 88.5 101 124 148

800 28.1 32.9 37.9 43.2 48.7 54.4 60.4 66.5 72.8 79.4 86.1 92.9 100 107 115 122 130 138 154 171 188 215 263 314

900 23.5 27.5 31.8 36.2 40.8 45.6 50.6 55.7 61.0 66.5 72.1 77.9 83.8 89.9 96.1 102 109 115 129 143 158 180 220 263

1000 20.1 23.5 27.1 30.9 34.9 39.0 43.2 47.6 52.1 56.8 61.6 66.5 71.6 76.7 82.0 87.4 92.9 98.6 110 122 135 154 188 224

1100 17.4 20.4 23.5 26.8 30.2 33.8 37.4 41.2 45.2 49.2 53.4 57.6 62.0 66.5 71.1 75.8 80.6 85.4 95.5 106 117 133 163 195

1200 15.3 17.9 20.6 23.5 26.5 29.6 32.9 36.2 39.6 43.2 46.8 50.6 54.4 58.4 62.4 66.5 70.7 75.0 83.8 92.9 102 117 143 171

HORSEPOWER RATINGS 450 33.9 38.0 42.1 46.3 50.5 54.6 58.8 63.1 67.3 71.7 76.0 80.3 84.6 89.0 93.5 98.0 102 106 115.5 124.5 133.5 147 170 192.5

500 37.3 41.8 46.3 50.9 55.5 60.1 64.7 69.4 74.1 78.8 83.6 88.3 93.1 97.9 103 108 112 117 127 137 147 162 187 212

600 700 43.2 34.3 49.2 40.1 54.6 46.3 59.9 52.8 65.3 59.5 70.8 66.5 76.3 73.8 81.8 81.3 87.3 89.0 92.9 97.0 98.5 105 104 114 110 122 115 131 121 139 127 146 132 152 138 159 150 172 161 185 173 199 190 219 220 253 250 287 TYPE C

Multiple Strand Chain HP Factors: Single Strand 1.0 Double Strand 1.9 Triple Strand 2.8 SPECIFICATION PAGES PT12-

RELATE PRO UCTS PAGES PT12-40

PT12-35

ENGINEERING/TECHNICAL PAGES PT12-42

Sprockets

No. Teeth 10 9 0.65 10 0.73 11 0.81 12 0.89 13 0.97 14 1.05 15 1.13 16 1.22 17 1.30 18 1.38 19 1.46 20 1.55 21 1.63 22 1.71 23 1.80 24 1.88 25 1.97 26 2.05 28 2.22 30 2.40 32 2.57 35 2.83 40 3.27 45 3.71 TYPE A

Conveyor Components

100 1-1/4” Pitch Single Strand Roller Chain

Engineering

Basic Horsepower Ratings

HT Synchrous Belts

DYNA-SYNC

SELECTION


DYNA-SYNC

SELECTION Basic Horsepower Ratings 140

1-3/4” Pitch Single Strand Roller Chain

HT Synchrous Belts Sprockets

No. Teeth 10 9 1.71 10 1.91 11 2.12 12 2.33 13 2.54 14 2.75 15 2.96 16 3.18 17 3.39 18 3.61 19 3.82 20 4.04 21 4.26 22 4.48 23 4.70 24 4.92 25 5.14 26 5.37 28 5.81 30 6.26 32 6.71 35 7.40 40 8.54 45 9.70 TYPE A

160

25 3.89 4.36 4.83 5.31 5.79 6.27 6.76 7.24 7.73 8.23 8.72 9.22 9.72 10.2 10.7 11.2 11.7 12.2 13.3 14.3 15.3 16.9 19.5 22.1

50 7.26 8.14 9.02 9.91 10.8 11.7 12.6 13.5 14.4 15.4 16.3 17.2 18.1 19.1 20.0 20.9 21.9 22.8 24.7 26.7 28.6 31.5 36.4 41.3

75 10.4 11.7 12.9 14.2 15.5 16.8 18.0 19.4 20.6 22.0 23.3 24.6 26.0 27.3 28.6 30.0 31.3 32.7 35.5 38.2 41.0 45.1 52.2 59.2

100 125 13.6 16.5 15.2 18.5 16.8 20.5 18.5 22.5 20.2 24.6 21.8 26.6 23.5 28.7 25.2 30.8 26.9 32.8 28.6 35.0 30.4 37.0 32.1 39.2 33.8 41.3 35.6 43.4 37.3 45.5 39.1 47.7 40.8 49.8 42.6 52.0 46.2 56.3 49.7 60.7 53.3 65.1 58.7 71.7 67.9 82.8 77.1 94.1 TYPE B

150 19.5 21.9 24.2 26.6 29.0 31.5 33.9 36.3 38.8 41.3 43.7 46.2 48.7 51.3 53.8 56.3 58.8 61.4 66.5 71.6 76.8 84.6 97.7 111

175 22.4 25.1 27.8 30.5 33.3 36.2 38.9 41.7 44.5 47.4 50.2 53.1 55.9 58.8 61.8 64.6 67.5 70.4 76.3 82.2 88.2 97.3 112 127.5

200 25.3 28.3 31.4 34.5 37.6 40.8 43.9 47.1 50.3 53.5 56.7 59.9 63.1 66.4 69.7 72.9 76.2 79.5 86.2 92.8 99.5 110 127 144

Conveyor Components Engineering

25 5.65 6.33 7.01 7.70 8.40 9.10 9.80 10.5 11.2 11.9 12.7 13.4 14.1 14.8 15.6 16.3 17.0 17.8 19.2 20.7 22.2 24.5 28.3 32.1

50 75 10.5 15.1 11.8 16.9 13.1 18.8 14.4 20.6 15.7 22.5 17.0 24.4 18.3 26.2 19.6 28.1 20.9 30.0 22.3 31.9 23.6 33.8 25.0 35.8 26.3 37.7 27.7 39.7 29.0 41.6 30.4 43.5 31.1 45.2 31.8 46.8 35.9 51.5 38.7 55.4 41.5 59.5 45.7 65.4 52.8 75.7 59.9 85.9 TYPE B

Lubrication Note TYPE A: Manual or Drip TYPE B: Bath or Disc TYPE C: Oil Stream

FEATURES/BENEFITS PAGE PT12-2

100 19.7 22.0 24.4 26.8 29.2 31.7 34.1 36.6 39.1 41.6 44.1 46.6 49.1 51.6 54.2 56.7 59.3 61.8 67.0 72.2 77.4 85.2 98.5 112

125 24.0 26.9 29.8 32.7 35.7 38.7 41.7 44.7 47.7 50.8 53.8 56.8 59.9 63.0 66.1 69.2 72.3 75.4 81.8 88.1 94.2 104 120 136

150 28.3 31.7 35.2 38.6 42.1 45.6 49.2 52.7 56.3 59.9 63.5 67.1 70.7 74.4 78.0 81.7 85.4 89.1 96.5 104 111 123 142 161

175 32.5 36.4 40.4 44.3 48.3 52.3 56.5 60.5 64.6 68.8 72.8 77.0 81.1 85.4 89.5 93.8 98.2 102 111 119 128 141 163 185

Small Sprocket RPM 225 250 275 300 28.1 30.9 33.7 36.4 31.4 34.6 37.7 40.8 34.9 38.4 41.8 45.2 38.3 42.2 46.0 49.7 41.8 46.0 50.1 54.2 45.3 49.8 54.3 58.7 48.8 53.7 58.5 63.2 52.3 57.5 62.7 67.8 55.8 61.4 66.9 72.4 59.4 65.3 71.2 77.0 63.0 69.3 75.4 81.6 66.6 73.2 79.8 86.3 70.1 77.2 84.1 91.0 73.8 81.2 88.4 95.6 77.4 85.2 92.6 100 81.1 89.2 97.1 105 84.7 93.2 102 110 88.3 97.2 106 115 95.6 105 114 124 102.9 113 124 134 111 122 132 143 122 134 146 158 141 155 168 182 160 176 192 207

325 39.1 43.8 48.6 53.4 58.2 63.1 67.9 72.9 77.8 82.8 87.7 92.7 97.5 103 107 113 118 124 134 144 154 169 196 222

350 400 41.8 47.2 46.9 52.9 52.0 58.6 57.1 64.4 62.2 70.2 67.4 76.0 72.7 81.9 77.9 87.8 83.2 93.8 88.5 99.8 93.8 106 99.1 112 104 118 110 124 115 130 121 136 126 142 132 148 143 161 154 173 165 186 181 205 210 236 238 268 TYPE C

450 52.5 58.8 65.2 71.6 78.0 84.5 91.1 97.7 104 111 118 124 131 138 145 151 158 165 179 193 206 227 263 298

500 57.7 64.6 71.6 78.7 85.8 93.0 100 107 115 122 129 137 144 151 159 166 174 181 197 212 227 250 289 328

550 55.7 65.2 75.2 85.7 93.5 101 109 117 125 133 141 149 157 165 173 181 189 198 214 231 247 272 315 357

600 48.9 57.2 66.0 75.2 84.8 94.8 105 116 127 138 150 161 170 178 187 196 205 214 232 249 267 295 340 387

700 38.8 45.4 52.4 59.7 67.3 75.2 83.4 91.9 101 110 119 128 138 148 158 169 180 190 213 236 260 297 363 434

800 31.7 37.2 42.9 48.9 55.1 61.6 68.3 75.2 82.4 89.8 97.4 105 113 121 130 138 147 156 174 193 213 243 297 355

400 450 500 550 600 68.5 76.1 71.5 62.0 54.4 76.7 85.3 83.7 72.6 63.7 85.0 94.5 96.6 83.7 73.5 93.4 104 110 95.4 83.7 102 113 124 108 94.4 110 123 135 120 105 119 132 145 133 117 127 142 156 147 129 136 151 166 161 141 145 161 177 175 154 153 171 188 190 167 162 180 198 205 180 171 190 209 221 194 180 200 220 237 208 189 210 231 251 222 197 220 241 263 237 206 229 252 275 252 215 239 263 287 267 233 259 285 311 298 251 279 307 336 331 269 300 329 359 365 297 330 363 395 417 343 381 419 457 494 389 433 476 519 561

700 43.2 50.5 58.3 66.4 74.9 83.7 92.8 102 112 122 132 143 154 165 176 188 200 212 237 263 289 331 404 482

HORSEPOWER RATINGS

2” Pitch Single Strand Roller Chain

No. Teeth 10 9 2.48 10 2.77 11 3.07 12 3.38 13 3.68 14 3.99 15 4.30 16 4.61 17 4.92 18 5.23 19 5.55 20 5.86 21 6.18 22 6.50 23 6.82 24 7.14 25 7.46 26 7.78 28 8.43 30 9.08 32 9.74 35 10.7 40 12.4 45 14.1 TYPE A

HORSEPOWER RATINGS

200 36.7 41.1 45.6 50.1 54.6 59.1 63.7 68.3 72.9 77.6 82.2 86.9 91.6 96.3 101 106 111 115 125 135 144 159 184 209

Small Sprocket RPM 225 250 275 300 40.8 44.8 48.8 52.8 45.7 50.3 54.8 59.2 50.7 55.7 60.7 65.6 55.7 61.2 66.7 72.1 60.6 66.7 72.6 78.6 65.7 72.3 78.8 85.2 70.8 77.9 84.8 91.7 75.9 83.5 90.9 98.4 81.0 89.1 97.1 105 86.2 94.8 103 112 91.6 101 109 118 96.4 106 115 125 102 112 122 132 107 118 128 139 112 124 135 146 117 129 141 152 123 135 147 159 128 141 153 166 139 153 166 180 150 165 179 194 160 176 192 208 176 194 212 229 205 225 245 265 232 255 278 301

325 350 56.8 60.7 63.6 68.0 70.5 75.4 77.4 82.8 84.4 90.3 91.5 97.8 98.3 105 106 113 113 121 120 128 127 136 135 144 142 152 149 159 156 167 163 175 171 183 179 191 193 207 209 223 223 239 246 263 284 304 323 345 TYPE C

375 64.6 72.3 80.2 88.1 96.2 104 112 120 128 136 145 153 162 169 178 186 195 203 220 237 254 280 324 367

Multiple Strand Chain HP Factors: Single Strand 1.0 Double Strand 1.9 Triple Strand 2.8

SPECIFICATION PAGES PT12-

RELATE PRO UCTS PAGES PT12-40

PT12-36

ENGINEERING/TECHNICAL PAGES PT12-42


Basic Horsepower Ratings

240

30 11.4 12.4 13.6 14.8 15.9 17.0 18.2 19.4 20.5 21.7 22.9 24.0 25.2 26.4 27.6 28.7 31.2 33.6 36.0 39.7

40 14.7 16.1 17.6 19.1 20.6 22.1 23.5 25.1 26.6 28.1 29.6 31.1 32.7 34.2 35.7 37.2 40.4 43.5 46.6 51.4

50 18.1 19.8 21.6 23.4 25.3 27.1 28.9 30.8 32.6 34.5 36.3 38.2 40.1 42.0 43.9 45.7 49.6 53.4 57.2 63.1 TYPE B

75 25.9 28.4 31.0 33.5 36.2 38.8 41.5 44.1 46.7 49.4 52.1 54.8 57.5 60.2 62.9 65.6 71.1 76.5 82.1 90.6

100 33.7 37.0 40.4 43.7 47.1 50.5 54.0 57.4 60.8 64.3 67.8 71.3 74.8 78.3 81.8 85.4 92.5 99.6 107 118

125 41.2 45.2 49.3 53.3 57.5 61.7 65.8 70.1 74.2 78.4 82.7 87.2 91.4 95.7 99.9 104 113 122 131 144

Small Sprocket RPM 150 175 200 48.6 55.7 62.9 53.4 61.3 69.1 58.2 66.8 75.4 63.0 72.3 81.6 67.9 77.9 88.0 72.8 83.6 94.3 77.7 89.3 101 82.7 94.8 107 87.6 101 114 92.6 106 120 97.6 112 126 103 118 133 108 124 140 113 129 146 118 135 153 123 141 159 133 153 173 144 165 186 154 176 199 170 195 220

15 8.12 8.92 9.72 10.5 11.3 12.2 13.0 13.8 14.6 15.5 16.3 17.2 18.0 18.9 19.7 20.6

20 10.5 11.6 12.6 13.6 14.7 15.8 16.8 17.9 19.0 20.1 21.1 22.2 23.3 24.4 25.5 26.6

30 15.1 16.6 18.1 19.7 21.2 22.7 24.2 25.8 27.3 28.9 30.5 32.0 33.6 35.2 36.8 38.4

40 19.6 21.6 23.5 25.5 27.4 29.4 31.4 33.4 35.4 37.4 39.5 41.5 43.5 45.6 47.6 49.7

50 24.0 26.4 28.7 31.1 33.5 36.0 38.4 40.8 43.3 45.8 48.2 50.7 53.2 55.7 58.2 60.7

60 28.3 31.0 33.8 36.6 39.5 42.3 45.2 48.0 50.9 53.8 56.8 59.7 62.6 65.6 68.5 71.4

Small Sprocket RPM 70 80 90 100 32.5 36.6 40.7 44.8 35.7 40.2 44.7 49.2 38.9 43.8 48.7 53.6 42.1 47.4 52.8 58.1 45.4 51.1 56.9 62.6 48.7 54.8 61.0 67.1 52.0 58.5 65.1 71.6 55.3 62.3 69.2 76.2 58.6 66.0 73.4 80.8 61.9 69.7 77.6 85.4 65.3 73.5 81.8 90.0 68.7 77.3 86.0 94.6 72.0 81.1 90.2 99.3 75.4 84.9 94.5 104 78.8 88.9 98.9 109 82.2 92.5 103 113 TYPE B

5 10 15 4.86 9.08 13.1 5.34 9.97 14.4 5.83 10.9 15.7 6.31 11.8 17.0 6.80 12.7 18.3 7.29 13.6 19.6 7.78 14.5 20.9 8.28 15.4 22.3 8.78 16.4 23.6 9.28 17.3 24.9 9.78 18.2 26.3 10.3 19.2 27.6 10.8 20.1 29.0 11.3 21.1 30.4 11.8 22.0 31.7 12.3 23.0 33.1 TYPE A Lubrication Note TYPE A: Manual or Drip TYPE B: Bath or Disc TYPE C: Oil Stream FEATURES/BENEFITS PAGE PT12-2

20 16.9 18.6 20.3 22.0 23.7 25.4 27.1 28.8 30.6 32.3 34.1 35.8 37.6 39.3 41.1 42.9

25 20.7 22.7 24.8 26.9 28.9 31.0 33.1 35.2 37.4 39.5 41.6 43.8 45.9 48.1 50.3 52.4

30 24.4 26.8 29.2 31.7 34.1 36.6 39.0 41.5 44.0 46.5 49.0 51.6 54.1 56.7 59.2 61.8

40 31.6 34.7 37.9 41.0 44.2 47.4 50.6 53.8 57.0 60.3 63.5 66.8 70.1 73.4 76.7 80.0

275 83.8 92.1 101 109 117 125 134 142 152 160 168 178 186 195 203 212 230 247 265 292 TYPE C

300 90.6 99.6 109 118 127 136 145 154 164 173 182 192 201 210 220 229 249 268 287 316

325 97.3 107 117 126 136 146 156 165 176 186 195 206 216 226 236 246 267 288 308 339

350 104 114 125 135 146 156 167 177 188 199 209 220 231 242 253 264 286 308 330 363

375 110 121 133 143 155 166 178 189 200 212 222 234 246 258 269 281 304 327 351 386

400 117 129 141 152 164 176 188 200 212 224 236 248 260 273 285 297 322 347 372 410

125 54.7 60.0 65.4 70.9 76.3 81.8 87.3 93.1 98.4 104 110 115 121 127 132 138

150 64.5 70.8 77.2 83.7 90.1 96.6 103 110 116 123 130 136 143 150 156 163

175 74.0 81.3 88.6 95.8 104 111 119 126 134 141 149 156 164 172 179 188

200 83.5 91.8 100 108 117 125 134 142 151 159 168 177 185 194 203 212

225 92.8 102 111 120 130 139 148 158 168 177 186 196 205 216 226 236

250 102 112 122 132 143 153 163 174 184 195 205 216 226 237 248 259 TYPE C

275 111 122 133 144 155 166 178 189 200 212 223 235 246 258 270 282

300 120 132 144 156 168 180 193 205 217 229 242 254 267 279 292 305

175 119 131 143 155 167 179 191 203 215 228 240 252 265 277 290 302

200 135 148 161 175 188 202 215 229 243 257 270 284 298 312 327 341 TYPE C

250 164 181 197 213 230 247 263 280 297 314 331 348 365 382 399 416

300 194 213 232 251 271 290 310 330 350 370 390 410 430 450 470 491

HORSEPOWER RATINGS

3” Pitch Single Strand Roller Chain

No. Teeth 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

250 76.9 84.5 92.1 99.8 108 115 123 131 139 147 155 163 171 179 187 195 211 227 244 268

HORSEPOWER RATINGS

2-1/2” Pitch Single Strand Roller Chain 10 5.64 6.19 6.75 7.31 7.88 8.45 9.02 9.59 10.2 10.7 11.3 11.9 12.5 13.1 13.7 14.3 TYPE A

225 69.9 76.8 83.8 90.7 98.0 105 112 119 126 134 141 148 155 162 170 177 192 206 222 244

Small Sprocket RPM 50 60 70 80 90 38.6 45.5 52.3 59.0 65.6 42.4 50.0 57.4 64.8 72.0 46.3 54.5 62.5 70.6 78.5 50.1 59.1 67.8 76.5 85.1 54.0 63.6 73.0 82.4 91.7 57.9 68.2 78.3 88.4 98.2 61.8 72.9 83.7 94.4 105 65.8 77.5 88.8 100 112 69.7 82.2 94.1 106 118 73.7 86.8 99.4 112 125 77.7 91.5 105 119 132 81.7 96.2 111 125 138 85.7 101 116 131 145 89.7 106 121 137 152 93.8 110 126 143 159 97.8 115 132 149 166 TYPE B Multiple Strand Chain HP Factors: Single Strand Double Strand Triple Strand

SPECIFICATION PAGES PT12-

100 72.1 79.2 86.4 93.6 101 108 115 123 130 138 145 152 160 167 175 183 1.0 1.9 2.8

RELATE PRO UCTS PAGES PT12-40

PT12-37

125 88.1 96.8 106 114 123 132 141 150 159 168 177 186 195 205 214 223

150 104 114 124 135 145 156 166 177 187 198 209 220 230 241 252 263

Shaded Area: Operation is in the galling range – consult factory ENGINEERING/TECHNICAL PAGES PT12-42

Sprockets

No. Teeth 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

20 7.87 8.62 9.43 10.2 11.0 11.8 12.6 13.4 14.2 15.0 15.8 16.7 17.5 18.3 19.1 19.9 21.6 23.2 24.9 27.5

Conveyor Components

No. Teeth 10 11 4.24 12 4.66 13 5.08 14 5.51 15 5.93 16 6.36 17 6.79 18 7.22 19 7.66 20 8.10 21 8.53 22 8.97 23 9.41 24 9.86 25 10.3 26 10.7 28 11.6 30 12.5 32 13.4 35 14.8 TYPE A

200

HORSEPOWER RATINGS

2-1/4” Pitch Single Strand Roller Chain

Engineering

180

HT Synchrous Belts

DYNA-SYNC

SELECTION


DYNA-SYNC

SELECTION Basic Horsepower Ratings 2040

HT Synchrous Belts Sprockets

No. of Effective Teeth, Small Spkt. 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 30

2050

— HP Ratings for 2040 Double Pitch Drive Chain HP Ratings @ Various RPM, Small Sprocket

Conveyor Components Engineering

25

50

100

150

200

250

300

350

400

450

500

550

600

700

800

900

.10 .12 .14 .16 .18 .20 .22 .24 .26 .28 .30 .32 .34 .36 .38 .40 .42 .44 .46 .48 .57

.17 .21 .25 .30 .34 .38 .42 .46 .50 .54 .57 .61 .65 .69 .72 .76 .79 .83 .87 .90 1.08 TYPE I

... .35 .64 .53 .61 .69 .77 .84 .92 .99 1.06 1.13 1.20 1.27 1.34 1.41 1.48 1.54 1.61 1.67 1.99

... .46 .72 .72 .82 .96 1.07 1.18 1.29 1.39 1.50 1.60 1.70 1.80 1.89 1.99 2.09 2.18 2.27 2.36 2.81

... .54 .82 .88 1.04 1.20 1.34 1.48 1.62 1.76 1.89 2.02 2.15 2.28 2.40 2.53 2.64 2.76 2.88 3.00 3.56

... ... .90 1.02 1.21 1.41 1.58 1.76 1.93 2.09 2.25 2.41 2.57 2.73 2.87 3.01 3.16 3.30 3.44 3.58 4.24

... ... ... 1.14 1.37 1.59 1.80 2.01 2.21 2.40 2.59 2.77 2.95 3.13 3.30 3.47 3.63 3.80 3.95 4.11 4.87

... ... ... 1.3 1.5 1.8 2.0 2.2 2.5 2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3 4.4 4.6 5.4

... ... ... ... ... ... 1.3 ... 1.6 1.7 1.9 2.0 2.2 2.3 2.4 2.6 2.7 2.9 2.9 3.2 3.2 3.4 3.4 3.7 3.6 3.9 3.9 4.2 4.1 4.4 4.3 4.6 4.5 4.9 4.7 5.1 4.9 5.3 5.1 5.5 6.0 6.5 TYPE Il

... ... ... ... 1.8 2.1 2.5 2.8 3.1 3.4 3.7 4.0 4.2 4.5 4.7 5.0 5.2 5.4 5.7 5.9 6.9

... ... ... ... 1.9 2.2 2.6 2.9 3.3 3.6 3.9 4.2 4.5 4.8 5.0 5.3 5.5 5.8 6.0 6.3 7.4

... ... ... ...

... ... ... ... ... ... 2.9 3.3 3.7 4.1 4.4 4.8 5.1 5.5 5.8 6.1 6.4 6.6 6.9 7.2 8.4

... ... ... ... ... ... 3.5 3.9 4.3 4.7 5.1 5.5 5.9 6.2 6.5 6.8 7.1 7.4 7.7 8.9

... ... ... ... ... ... ... ... 4.1 4.5 5.0 5.4 5.8 6.2 6.5 6.9 7.2 7.5 7.8 8.1 9.4

... ... ... ... ... ... ... ... ... 4.7 5.1 5.6 6.0 6.4 6.8 7.1 7.5 7.8 8.1 8.4 9.7 TYPE Ill

... ... ... ... ... ... ... ... ... ... ... 5.7 6.2 6.6 7.0 7.4 7.7 8.0 8.4 8.7 10.0

... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 6.7 ... 7.1 ... 7.5 ... 7.9 ... 8.2 8.3 8.5 8.6 8.8 8.9 10.1 10.1

700

750

800

850

900

... ... ... ... ... ... ... ... ... ... ... 8.62 9.28 9.90 10.49 11.06 11.59 12.10 12.59 13.05 15.06

... ... ... ... ... ... ... ... ... ... ... ... ... 10.08 10.69 11.28 11.83 12.35 12.85 13.33 15.30

2.3 2.7 3.1 3.4 3.8 4.1 4.4 4.7 5.0 5.3 5.6 5.8 6.1 6.4 6.6 7.8

1000 1100 1200 1300

— HP Ratings for 2050 Double Pitch Drive Chain

No. of Effective Teeth, 25 50 Small Spkt. 6 .18 .31 7 .22 .40 8 .26 .48 9 .31 .56 10 .35 .64 11 .39 .72 12 .43 .80 13 .47 .88 14 .51 .95 15 .55 1.02 16 .58 1.09 17 .62 1.17 18 .66 1.24 19 .70 1.31 20 .74 1.38 21 .77 1.45 22 .81 1.52 23 .84 1.59 24 .88 1.66 25 .91 1.72 30 1.09 2.05 TYPE I

FEATURES/BENEFITS PAGE PT12-2

HP Ratings @ Various RPM, Small Sprocket 100

150

200

250

300

350

400

... .65 .82 .98 1.14 1.30 1.45 1.59 1.73 1.87 2.01 2.14 2.27 2.40 2.53 2.66 2.79 2.92 3.05 3.17 3.77

... ... 1.08 1.32 1.55 1.77 1.99 2.20 2.41 2.62 2.82 3.01 3.20 3.39 3.57 3.75 3.92 4.10 4.27 4.45 5.29

... ... 1.28 1.59 1.89 2.19 2.47 2.74 3.01 3.27 3.52 3.77 4.01 4.25 4.48 4.71 4.93 5.15 5.37 5.59 6.62

... ... ... 1.82 2.19 2.55 2.90 3.23 3.55 3.87 4.17 4.46 4.75 5.04 5.32 5.59 5.85 6.11 6.37 6.62 7.82

... ... ... ... ... ... ... ... ... 1.99 ... ... 2.42 2.62 2.80 2.85 3.11 3.35 3.26 3.58 3.88 3.65 4.03 4.38 4.02 4.45 4.85 4.37 4.86 5.30 4.72 5.25 5.73 5.07 5.67 6.15 5.41 6.04 6.56 5.75 6.40 6.96 6.07 6.75 7.35 6.38 7.10 7.74 6.69 7.44 8.12 6.99 7.77 8.49 7.29 8.10 8.85 7.57 8.42 9.20 8.92 9.92 10.80 TYPE Il

450

500

550

600

650

... ... ... ... ... 3.55 4.12 4.66 5.17 5.67 6.15 6.61 7.07 7.51 7.94 8.36 8.77 9.16 9.54 9.91 11.65

... ... ... ... ... ... 4.31 4.90 5.47 6.01 6.53 7.05 7.54 8.01 8.46 8.90 9.33 9.75 10.16 10.56 12.32

... ... ... ... ... ... ... 5.11 5.73 6.31 6.87 7.42 7.95 8.46 8.94 9.40 9.84 10.27 10.70 11.12 12.99

... ... ... ... ... ... ... 5.30 5.95 6.57 7.17 7.74 8.29 8.82 9.33 9.82 10.29 10.74 11.18 11.61 13.55

... ... ... ... ... ... ... ... 6.09 6.75 7.39 7.99 8.56 9.12 9.65 10.16 10.65 11.12 11.57 12.01 13.96

SPECIFICATION PAGES PT12-

RELATE PRO UCTS PAGES PT12-40

PT12-38

... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 6.94 ... 7.61 7.79 8.24 8.46 8.84 9.08 9.42 9.68 9.97 10.25 10.50 10.80 11.01 11.32 11.50 11.82 11.97 12.30 12.42 12.75 14.39 14.76 TYPE Ill

950

... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 11.44 ... 12.00 ... 12.53 ... 13.03 ... 13.50 13.57 15.48 ...

ENGINEERING/TECHNICAL PAGES PT12-42


DYNA-SYNC

SELECTION Basic Horsepower Ratings

No. of Effective Teeth, Small Spkt. 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 30

25 .30 .37 .44 .52 .59 .66 .73 .79 .86 .92 .99 1.05 1.12 1.18 1.25 1.31 1.37 1.44 1.50 1.56 1.86

50

75

... ... .66 .88 .80 1.09 .94 1.30 1.08 1.51 1.21 1.71 1.34 1.90 1.47 2.09 1.60 2.27 1.72 2.45 1.85 2.64 1.97 2.82 2.10 3.00 2.22 3.17 2.34 3.34 2.46 3.51 2.58 3.67 2.69 3.84 2.80 4.00 2.92 4.17 3.48 4.96 TYPE I

100

125

150

175

200

... 1.06 1.34 1.62 1.89 2.15 2.41 2.66 2.90 3.14 3.37 3.59 3.82 4.04 4.25 4.48 4.70 4.91 5.12 5.32 6.32

... ... 1.56 1.90 2.23 2.54 2.85 3.15 3.45 3.74 4.02 4.29 4.56 4.83 5.09 5.36 5.62 5.87 6.12 6.36 7.58

... ... 1.74 2.15 2.54 2.92 3.29 3.65 4.00 4.34 4.67 4.99 5.31 5.62 5.93 6.24 6.54 6.83 7.12 7.41 8.78

... ... ... ... 1.89 ... 2.36 2.55 2.82 3.07 3.25 3.58 3.67 4.06 4.08 4.52 4.48 4.96 4.86 5.39 5.24 5.81 5.61 6.22 5.97 6.63 6.32 7.03 6.67 7.42 7.02 7.80 7.35 8.17 7.68 8.54 8.01 8.91 8.34 9.27 9.86 10.94

225 ... ... ... 2.72 3.29 3.84 4.37 4.88 5.37 5.85 6.32 6.78 7.23 7.67 8.09 8.50 8.90 9.30 9.69 10.08 11.85

250

275

... ... ... ... ... ... ... ... 3.50 3.68 4.12 4.34 4.71 4.97 5.27 5.59 5.80 6.17 6.32 6.73 6.82 7.27 7.32 7.80 7.81 8.32 8.29 8.83 8.74 9.33 9.19 9.81 9.63 10.28 10.06 10.74 10.48 11.19 10.89 11.62 12.76 13.71 TYPE II

300

350

400

450

500

550

... ... ... ... 3.83 4.56 5.24 5.91 6.54 7.14 7.72 8.29 8.84 9.38 9.91 10.43 10.93 11.42 11.90 12.37 14.55

... ... ... ... ... 4.93 5.71 6.46 7.17 7.86 8.52 9.16 9.78 10.38 10.95 11.53 12.08 12.62 13.15 13.58 15.98

... ... ... ... ... ... 6.06 6.92 7.72 8.48 9.21 9.91 10.58 11.23 11.86 12.47 13.06 13.63 14.18 14.72 17.28

... ... ... ... ... ... ... 7.25 8.10 8.92 9.71 10.47 11.21 11.93 12.62 13.28 13.92 14.54 15.15 15.75 18.40

... ... ... ... ... ... ... ... 8.51 9.40 10.25 11.06 11.84 12.60 13.34 14.05 14.73 15.39 16.03 16.65 19.40

225

250

600

... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 10.70 ... 11.59 11.99 12.42 12.88 13.22 13.73 13.99 14.54 14.73 15.31 15.44 16.05 16.12 16.76 16.77 17.44 17.40 18.09 20.22 20.92 TYPE III

650

700

... ... ... ... ... ... ... ... ... ... ... ... ... 14.14 14.99 15.80 16.57 17.30 18.00 18.67 21.32

... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 17.78 18.40 19.09 22.00

400

450

— HP Ratings for 2080 Double Pitch Drive Chain

HT Synchrous Belts

HP Ratings @ Various RPM, Small Sprocket

Sprockets

2080

— HP Ratings for 2060 Double Pitch Drive Chain

HP Ratings @ Various RPM, Small Sprocket 10

20

30

.32 .38 .46 .52 .59 .66 .72 .79 .85 .91 .98 1.04 1.11 1.17 1.23 1.29 1.36 1.42 1.48 1.54 1.84

.55 .70 .84 .98 1.11 1.24 1.37 1.49 1.62 1.74 1.87 1.99 2.11 2.23 2.35 2.47 2.58 2.70 2.82 2.93 3.50

.76 .98 1.18 1.39 1.58 1.77 1.96 2.15 2.33 2.52 2.70 2.88 3.05 3.23 3.40 3.57 3.74 3.90 4.05 4.20 5.02

40

50

... ... 1.22 1.44 1.50 1.78 1.76 2.11 2.02 2.43 2.27 2.76 2.52 3.08 2.77 3.38 3.01 3.67 3.25 3.96 3.48 4.24 3.71 4.52 3.94 4.80 4.17 5.08 4.40 5.35 4.62 5.62 4.84 5.89 5.06 6.16 5.27 6.43 5.48 6.70 6.54 7.96 TYPE I

60

70

... ... 1.63 1.80 2.04 2.28 2.43 2.74 2.82 3.18 3.20 3.60 3.56 4.02 3.81 4.44 4.26 4.85 4.60 5.25 4.94 5.64 5.28 6.02 5.61 6.40 5.94 6.77 6.26 7.13 6.58 7.49 6.89 7.84 7.20 8.19 7.51 8.54 7.81 8.89 9.29 10.59

80

90

100

125

150

175

... ... 2.50 3.02 3.53 4.02 4.50 4.97 5.42 5.86 6.29 6.72 7.14 7.56 7.98 8.39 8.79 9.18 9.56 9.94 11.74

... ... 2.70 3.29 3.85 4.38 4.92 5.45 5.96 6.45 6.93 7.40 7.87 8.33 8.78 9.23 9.67 10.10 10.53 10.95 12.97

... ... 2.88 3.53 4.16 4.77 5.36 5.93 6.49 7.03 7.56 8.09 8.60 9.10 9.60 10.09 10.57 11.05 11.52 11.98 14.23

... ... ... 4.08 4.85 5.60 6.33 7.02 7.69 8.34 8.98 9.61 10.23 10.84 11.44 12.03 12.62 13.20 13.77 14.33 16.98

... ... ... 4.54 5.45 6.33 7.19 8.02 8.82 9.60 10.36 11.10 11.82 12.52 13.20 13.87 14.53 15.18 15.82 16.45 19.46

... ... ... ... 5.98 6.98 7.95 8.89 9.80 10.68 11.53 12.36 13.18 13.98 14.76 15.52 16.27 17.01 17.74 18.46 21.79

Explanation of Lubrication: TYPE I: Steady Drip (4-10 drops/minute) shallow bath or manual w/ oil applied by brush or spout can to link plate edges when in lower span of chain.

FEATURES/BENEFITS PAGE PT12-2

SPECIFICATION PAGES PT12-

300

350

... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 7.56 8.07 ... ... ... ... ... 8.66 9.27 9.82 ... ... ... ... 9.72 10.42 11.08 ... ... ... ... 10.74 11.53 12.29 13.60 ... ... ... 11.73 12.60 13.46 14.94 ... ... ... 12.69 13.63 14.59 16.24 17.65 ... ... 13.62 14.63 15.69 17.50 19.04 ... ... 14.52 15.60 16.76 18.72 20.38 21.77 ... 15.39 16.55 17.80 19.90 21.67 23.18 ... 16.24 17.48 18.81 21.04 22.91 24.52 ... 17.07 18.39 19.79 22.14 24.11 25.80 ... 17.89 19.28 20.74 23.20 25.27 27.03 ... 18.70 20.15 21.66 24.23 26.40 28.22 ... 19.50 21.01 22.55 25.23 27.50 29.38 30.98 20.29 21.86 23.42 26.20 28.57 30.52 32.16 23.91 25.73 27.52 30.70 33.56 35.52 37.26 TYPE II TYPE III TYPE II: Rapid Drip (20 drops/minute, min.) or continuous w/ shallow bath, disc or slinger. TYPE III: Continuous w/disc, slinger or circulating pump. Additional Information–ANSI Roller Chain Standard B29.3, Section A1.3.

RELATE PRO UCTS PAGES PT12-40

PT12-39

200

ENGINEERING/TECHNICAL PAGES PT12-42

Conveyor Components

No. of Effective Teeth, Small Spkt. 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 30

Engineering

2060


DYNA-SYNC

RELATED PRODUCTS Tensioner Frame, Idler Sprockets Proper chain tension is necessary for normal life expectancy. It's also a prime consideration for the efficient, quiet operation of the drive.

HT Synchrous Belts

The tensioner frame shown below provides an economical means of locating an idler sprocket on a 1/2, diameter machine bolt or a 5/8, diameter spacer. Frame can be mounted in several positions on surfaces either parallel or perpendicular to the chain, suitable for either conventional or cantilever mounting.

CHAIN TENSIONER FRAME, P/N 102050 This formed steel frame has mounting holes in the bottom and one side so it can be mounted in several positions on surfaces parallel or perpendicular to the chain. Included is a 5/8” O.D. sleeve and a 1/2” diameter machine bolt to use with 1/2” and 5/8” bore idler sprockets. Spacer washers may be used to obtain the chain clearance required. Idler sprocket table below shows minimum space required for chain clearance. Part Number 102050, Weight .73 lbs.

Sprockets

IDLER SPROCKETS Although these idler sprockets are designed to be used with the frames shown above, they can be mounted on standard machine bolts as shown in table below.

Conveyor Components

Idler sprockets will operate at the same speeds permitted for driver sprockets of the same number of teeth. They are machined all over with teeth hardened to assure smoothrunning drives. They are available with either bronze sleeve or ball bearings in the sprocket bore. The sleeve bearing runs on a hardened and ground steel journal. The ball bearings are double-sealed and prelubricated. For Chain: No.

Pitch

35

3/8"

41-40 40 50

1/2”

5/8"

Engineering

60, 60H

3/4"

80,80H

1"

Description +

Part No.

31E20 35BB20H 41E15 40BB17H 40BB18H 51E15 50BB15H 50BB17H 61E14 60BB13H 60BB15H 80BB12H

102052 102060 102053 102061 102070 102054 102062 102073 102055 102063 Δ 102064

SLEEVE BEARING TYPE

No. of Spkt. Teeth

Spkt. O.D.

20

2.593

15 17 18

2.652 2.974 3.14

15

3.315

17 14 13 15 12

.372 3.736 3.493 3.98 4.332

* Minimum space required for chain clearance. † Size of standard machine bolt on which sprocket can be mounted.

FEATURES/BENEFITS PAGE PT12-2

SPECIFICATION PAGES PT12-3

Brg. Type

Wt.

Brz. Ball Brz. Ball Ball Brz Ball Ball Brz. Ball Ball Ball

53 .30 .58 .50 .53 .83 .60 .78 1.09 .90 1.06 1.5

A

*

B †

Ref. Old No.

.59 .44 .59 .44 .44 .72 .56 .56 .81 .66 .66 .69

1/2 5/8 1/2 5/8 5/8 1/2 5/8 5/8 1/2 5/8 5/8 5/8

CT320 320H CT415 417H ... CT515 515H ... CT614 613H ... 812H

Δ Non-Stock. Allow 2-4 weeks delivery. + "H" suffix indicates hardened teeth

SELECTION PAGES PT12-28

PT12-40

BALL BEARING TYPE

ENGINEERING/TECHNICAL PAGES PT12-42


Chain Pin Extractors (Chain Breaker)

Chain Assembly Tools

For Chain Nos. 35 thru 60 80 thru 240

Jaw Spread of Tool 2" 5"

Part No. 098190 098191

Wt, (Lbs,) .4 2.2

This fast working tool is practical for removing chain pins when roller chain needs to be disconnected or when various lengths of chain need to be made up. Three sizes of pin extractors are available to use on riveted and cottered chain, sizes 25 thru 160. This tool, if properly used, will not damage chain and pins can be reused. For Chain Nos.

Part No.

25 thru 50 098175 60 thru 100 098176 120 thru 160 098177

Ref. Model No. 101-1 101-2 101-3

Wt. (Lbs.) 1.0 1.9 8.5

Replacement Parts Screw & Tip Only Tip 391301* 098180 391304 098181 391308 098182

Sprockets

This unique tool was designed to make sizes 35 thru 240 chain installation easy. By hooking the two jaws into each end of the chain and turning the screw (handle) until the two ends almost meet, the connecting link can be inserted and fastened in place. The photo shows the Model 35 tool. The Model 80 uses aT-handle instead of a knob.

DYNA-SYNC

Chain Tools

HT Synchrous Belts

RELATED PRODUCTS

TORQUE-TAMER torque overload clutch offers thrifty overload protection that's a cinch to adjust.

Engineering

See TORQUE TAMER Section for complete specifications and ordering information.

Conveyor Components

* Includes handle.

FEATURES/BENEFITS PAGE PT12-2

SPECIFICATION PAGES PT12-3

SELECTION PAGES PT12-28

PT12-41

ENGINEERING/TECHNICAL PAGES PT12-42


DYNA-SYNC

ENGINEERING/TECHNICAL Custom TAPER-LOCK Sprockets Non-stock or special TAPER-LOCK sprockets may be fabricated from stock TAPER-LOCK hubs and A-Plate sprockets rebored to fit the hubs. This provides the capability for fabricating sprockets with larger bore capacity, or number of teeth that are stocked as A-Plate but not TAPER-LOCK. This operation can be done on location, or supplied by DODGE, price on application.

+

=

HT Synchrous Belts

DODGE TAPER-LOCK hubs are available in three types: S, K and W/WA. All are of quality steel bar stock or forgings, easily welded, and ready to accept TAPER-LOCK Bushings. For more detailed information and dimensions, refer to Bushings/Hubs section of this catalog. EXAMPLES

Sprockets

Chain No. TAPER-LOCK Pitch Teeth Hub 50 50 S30-6 60 34 S20-6 60 96 S35 100 42 835 140 80 WA60 240 54 WA70

A-Plate Sprocket 50A50 60A34 60A96 100A42 140A80 240A54

DODGE TAPER-LOCK WELD-ON HUB

Fabricated Sprocket 50BTL50 60BTL34 60BTL96 100BTL42 140CTL80 240CTL54

+

A-PLATE SPROCKET REBORE TO “G” DIMENSION, WELD

TAPER-LOCK SPROCKET

=

TAPER-LOCK Hub/A-Plate Data Table

Conveyor Components

Hub No. ◊

Part No.

S16-4 S16-6 S20-6 S20-8 S25-6 S25-8 S25-10 S25-16 S30-10 S30-16 S35 WA40 WA45 WA50 WA60 WA70 WA80 WA100

097023 097024 097025 097015 097016 097017 097018 097019 097020 097021 097022 228089 228090 228091 228092 228093 228094 228095

For Use Bushing With Bore Bush. Range + 1610 1/2 - 11/16 1610 1/2 - 11/16 2012 1/2 - 2-1/8 2012 1/2 - 2-1/8 2517 1/2 - 2-11/16 2517 1/2 - 2-11/16 2517 1/2 - 2-11/16 2517 1/2 - 2-11/16 3020 7/8 - 3-1/4 3020 7/8 - 3-1/4 3535 1-3/16 - 3-15/16 4040 1-7/16 - 4-7/16 4545 1-15/16 - 4-15/16 5050 2-7/16 - 5 6050 3-7/16 - 6 7060 3-15/16 - 7 8065 4-7/16 - 8 10085 7 - 10

Minimum Number Teeth for Chain Pitch No. A-Plate Rebore Dia. 2.875Δ 2.875Δ 3.4375Δ 3.4375Δ 4.125Δ 4.125Δ 4.125Δ 4.125Δ 5.125Δ 5.125Δ 6.375Δ 7.250Δ 8.000+ 8.750+ 12.250+ 13.500+ 14.250+ 18.750+

Engineering

◊ Refer to D1-12 & 13 for hub dimensions

FEATURES/BENEFITS PAGE PT12-2

35

40/41

50

60

80

100

120

140

160

180

200

240

31 – 36 – 42 – – – 49 – – – – – – – – –

24 – 28 – 33 – – – 39 – 44 – – – – – – –

– 21 24 – 27 – – – 32 – 38 45 50 52 – – – –

– 19 21 – 24 – – – 28 – 33 38 43 46 – – – –

– – – 17 – 19 – – 22 – 26 30 33 35 47 51 – –

– – – – – – 16 – 19 – 22 25 28 29 39 42 44 –

– – – – – – – 15 – – 20 22 24 26 34 36 38 47

– – – – – – – 13 – 17 17 20 21 23 29 32 33 41

– – – – – – – 12 – 15 16 18 20 21 26 28 30 36

– – – – – – – – – 14 – 17 18 19 24 26 27 33

– – – – – – – – – – – 15 17 18 22 24 25 30

– – – – – – – – – – – – 15 15 19 21 21 26

REBORE TOLERANCES Δ +.004 + .001 + +.010 + .004

SPECIFICATION PAGES PT12-

SELECTION PAGES PT12-2

PT12-42

RELATE PRO UCTS PAGES PT12-40


35 1.097 1.214 1.331 1.449 1.567 1.685 1.804 1.922 2.041 2.160 2.279 2.397 2.516 2.635 2.754 2.873 2.992 3.111 3.230 3.349 3.468 3.588 3.707 3.826 3.945 4.064 4.184 4.303 4.422 4.541 4.661 4.780 4.599 5.018 5.138 5.257 5.376 5.495 5.615 5.734 5.853 5.972 6.092 6.211 6.330 6.449 6.569 6.688 6.807 6.927 7.046 7.165 8.120 5.597 9.074 9.552 10.029 11.342 11.461 12.177 13.371

FEATURES/BENEFITS PAGE PT12-2

41 1.462 1.618 1.775 1.932 2.089 2.247 2.405 2.563 2.721 2.879 3.038 3.196 3.355 3.513 3.673 3.831 3.989 4.148 4.307 4.465 4.625 4.783 4.942 5.101 5.260 5.419 5.578 5.737 5.896 6.055 6.214 6.373 6.532 6.691 6.850 7.009 7.168 7.327 7.486 7.645 7.804 7.963 8.122 8.281 8.440 8.599 8.758 8.917 9.077 9.235 9.395 9.554 10.826 11.463 12.099 12.736 13.372 15.122 15.282 16.236 17.827

40 1.462 1.618 1.775 1.932 2.089 2.247 2.405 2.563 2.721 2.879 3.038 3.196 3.355 3.513 3.672 3.831 3.959 4.148 4.307 4.465 4.625 4.783 4.942 5.101 5.260 5.419 5.578 5.737 5.896 6.055 6.214 6.373 6.532 6.691 6.850 7.009 7.168 7.327 7.486 7.645 7.804 7.963 8.122 8.281 8.440 8.599 8.758 5.917 9.077 9.235 9.395 9.554 10.826 11.463 12.099 12.736 13.372 15.122 15.252 16.236 17.527

50 1.828 2.023 2.219 2.415 2.612 2.809 3.006 3.204 3.401 3.599 3.798 3.995 4.194 4.392 4.590 4.788 4.987 5.185 5.384 5.582 5.781 5.979 6.178 6.376 6.575 6.774 6.973 7.171 7.370 7.569 8.768 7.966 8.165 8.364 8.563 8.761 8.960 9.159 9.358 9.556 9.755 9.954 10.153 10.351 10.550 10.749 10.948 11.147 11.346 11.544 11.743 11.942 13.533 14.329 15.124 15.919 16.715 18.903 19.102 20.296 22.284

60 2.193 2.427 2.663 2.898 3.134 3.371 3.608 3.845 4.082 4.319 4.557 4.794 5.033 5.270 5.508 5.746 5.984 6.222 6.461 6.698 6.937 7.175 7.413 7.652 7.890 8.129 8.367 8.606 8.841 9.083 9.321 9.560 9.798 10.037 10.275 10.514 10.752 10.991 11.229 11.468 11.706 11.945 12.183 12.422 12.660 12.599 13.137 13.376 13.615 13.853 14.092 14.330 16.240 17.195 18.149 19.103 20.058 22.684 22.922 24.355 26.741

Chain Number 80 100 3.655 2.924 4.045 3.236 4.438 3.550 4.830 3.864 5.224 4.179 5.618 4.494 6.013 4.810 6.408 5.126 6.803 5.442 7.199 5.759 7.595 6.076 7.990 6.392 8.388 6.710 8.784 7.027 9.180 7.344 9.576 7.661 9.974 7.979 10.370 8.296 10.768 8.614 11.164 8.931 11.561 9.249 11.959 9.567 12.355 9.884 10.202 12.753 10.520 13.150 10.838 13.548 11.156 13.945 11.474 14.343 11.792 14.740 12.110 15.138 12.428 15.535 12.745 15.933 13.064 16.330 13.382 16.728 13.700 17.125 14.018 17.523 14.336 17.920 14.654 18.318 14.972 18.715 15.290 19.113 15.608 19.510 15.926 19.908 16.244 20.305 16.562 20.703 16.850 21.100 17.198 21.498 17.516 21.895 17.835 22.294 18.153 22.691 18.789 23.089 18.789 23.486 19.107 23.584 21.653 27.066 22.926 28.658 24.198 30.248 25.471 31.839 26.744 33.430 30.245 37.806 30.563 38.204 32.473 40.591 35.655 44.569

SPECIFICATION PAGES PT12-

120 4.356 4.854 5.325 5.796 6.269 6.741 7.215 7.698 8.163 8.639 9.114 9.588 10.065 10.541 11.016 11.492 11.969 12.444 12.921 13.397 13.874 14.351 14.826 15.303 15.780 16.257 16.734 17.211 17.688 18.165 18.642 19.119 19.596 20.073 20.550 21.027 21.504 21.981 22.458 22.935 23.412 23.889 24.366 24.843 25.320 25.797 26.274 26.753 27.230 27.707 28.184 28.661 32.480 34.359 36.297 38.207 40.116 45.368 45.845 48.710 53.483

SELECTION PAGES PT12-2

PT12-43

140 5.117 5.663 6.213 6.762 7.313 7.865 8.418 8.971 9.524 10.078 10.633 11.186 11.743 12.297 12.852 13.407 13.963 14.518 15.075 15.629 16.186 16.742 17.297 17.854 18.410 18.967 19.523 20.080 20.636 21.193 21.749 22.306 22.862 23.419 23.975 24.532 25.088 25.645 26.201 26.758 27.314 27.871 28.427 28.984 29.540 30.097 30.653 31.211 31.765 32.324 32.881 33.437 37.893 40.121 42.347 44.574 46.802 52.929 53.485 56.828 62.396

160 5.848 6.472 7.100 7.728 8.358 8.988 9.620 10.252 10.844 11.518 12.152 12.784 13.420 14.054 14.688 15.322 15.958 16.592 17.228 17.862 18.498 19.134 19.768 20.404 21.040 21.676 22.312 22.948 23.584 24.220 24.856 25.492 26.128 26.764 27.400 28.036 28.672 29.308 29.944 30.580 31.216 31.852 32.488 33.124 33.760 34.396 35.032 35.670 36.306 36.942 37.578 38.214 43.306 45.852 48.396 50.942 53.488 60.490 61.126 64.946 71.310

180 6.579 7.281 7.986 8.693 9.402 10.112 10.822 11.533 12.245 12.957 13.670 14.383 15.096 15.810 16.524 17.238 17.952 18.666 19.381 20.096 20.810 21.525 22.240 22.955 23.670 24.385 25.101 25.815 26.531 27.246 27.962 28.677 29.393 30.108 30.824 31.539 32.255 32.971 33.686 34.402 35.118 35.834 36.549 37.265 37.981 38.696 39.412 40.128 40.844 41.560 42.276 42.991 48.719 51.583 54.446 57.310 60.175 68.051 68.767 73.064 80.225

200 7.310 8.090 8.875 9.660 10.447 11.235 12.025 12.815 13.605 14.397 15.190 15.980 16.775 17.567 18.360 19.153 19.947 20.740 21.535 22.327 23.123 23.917 24.710 25.505 26.300 27.095 27.890 28.685 29.480 30.275 31.070 31.865 32.660 33.455 34.250 35.045 35.840 36.635 37.430 38.225 39.020 39.815 40.610 41.405 42.200 42.995 43.790 44.587 45.383 46.177 46.973 47.768 54.132 57.315 60.495 63.678 66.860 75.612 76.408 81.182 59.137

240 8.771 9.708 10.649 11.591 12.536 13.482 14.429 15.377 16.327 17.276 18.227 19.177 20.129 21.080 22.032 22.984 23.936 24.889 25.841 26.794 27.747 28.700 29.654 30.607 31.560 32.514 33.467 34.421 35.375 36.329 37.283 38.237 39.191 40.145 41.099 42.053 43.007 43.961 44.915 45.869 46.824 47.778 45.732 49.687 50.641 51.595 52.550 53.504 54.458 55.413 56.368 57.322 64.958 68.777 72.595 76.414 80.233 90.735 91.690 97.418 106.966

RELATE PRO UCTS PAGES PT12-40

Sprockets

25 .731 .809 .887 .996 1.045 1.124 1.203 1.282 1.361 1.440 1.519 1.598 1.678 1.757 1.836 1.915 1.995 2.074 .... 2.233 .... 2.392 .... 2.551 .... .... .... 2.869 .... .... ... 3.187 .... .... .... .... 3.584 .... .... 3.823 .... .... .... .... .... 4.300 .... .... .... .... .... 4.777 .... 5.732 .... .... .... .... .... .... ....

Conveyor Components

No. Teeth 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 55 59 60 68 72 76 80 84 95 96 102 112

Engineering

Sprocket Pitch Diameters

HT Synchrous Belts

DYNA-SYNC

ENGINEERING/TECHNICAL


DYNA-SYNC

ENGINEERING/TECHNICAL Sprocket Dimensions, Chain Data Sprocket Tooth Profile Dimensions Ref. For Single & Multiple Chain

HT Synchrous Belts

*

G

Chain No.

Pitch

Roller Dia.

Roller Width

35 41 40 50 60 80 100 120 140 160

3/8 1/2 1/2 5/8 3/4 1 1-1/4 1-1/2 1-3/4 2

.200 .306 .312 .400 .469 .625 .750 .875 1.000 1.125

3/16 1/4 5/16 3/8 1/2 5/8 3/4 1 1 1-1/4

3/64 1/16 1/16 5/64 3/32 1/8 5/32 3/16 7/32 1/4

H

3/16 1/4 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1

K

.399 .... .566 .713 .897 1.153 1.408 1.789 1.924 2.305

M2

R Max.

M3

.015 .020 .020 .025 .030 .040 .050 .060 .070 .080

.960 .... 1.407 1.758 2.238 2.863 3.485 4.472 4.742 5.729

.561 .... .841 1.045 1.341 1.710 2.077 2.683 2.818 3.424

Nominal Tooth Thickness (T) Using Using Single 2 and 3 Strand Strand Chain Chain .162 .168 .... .227 .275 .284 .332 .343 .444 .459 .557 .575 .669 .692 .894 .924 .894 .924 1.119 1.156

Tolerance on "T" For Machined Sprocket

* +.000–.008 +.000–.009 +.000–.009 +.000–.010 +.000–.011 +.000–.012 +.000–.014 +.000–.016 +.000–.016 +.000–.019

For Sprocket Which Is Not Machined† +.000–.027 +.000–.032 +.000–.035 +.000–.036 +.000–.036 +.000–.040 +.000–.046 +.000–.057 +.000–.057 +.000–.062

W Side Clearance 3/16 7/32 1/4 9/32 11/32 7/16 17/32 21/32 3/4 7/8

† Represents an "A" plate sprocket or a welded sprocket using an "A" plate.

Represents Type B or C hub type sprocket.

Sprockets

Roller Chain

Sprockets Conveyor Components

ANSI Standard Roller Chain Dimensions ANSI No.

Engineering

25-2 25-2 25-3 35 35-2 35-3 41 40 40-2 40-3 50 50-2 50-3 60 60-2 60-3 80 80-2 80-3

Roller Roller W D 1/8 1/8 1/8 3/16 3/16 3/16 1/4 5/16 5/16 5/16 3/8 3/8 3/8 1/2 1/2 1/2 5/8 5/8 5/8

.130 .130 .130 .200 .200 .200 .306 .312 .312 .312 .400 .400 .400 .469 .469 .469 .625 .625 .625

Inside Link Plate Height .237 .237 .237 .356 .356 .356 .383 .475 .475 .475 .594 .594 .594 .712 .712 .712 .950 .950 .950

Cottered Riveted Average Tensile Chain Chain Width* Width* Strength 875 .34 .37 1750 .59 .63 2626 .84 .88 2100 .50 .56 4200 .90 .96 6300 1.31 1.36 .65 .57 2000 3700 .67 .72 7400 1.24 1.29 11100 1.80 1.85 6600 .83 .89 13200 1.55 1.60 19800 2.26 2.31 8500 1.04 1.11 17000 1.94 2.01 25500 2.84 2.91 14500 1.32 1.44 29000 2.47 2.59 43500 3.62 3.74

* Dimensions are across pins. FEATURES/BENEFITS PAGE PT12-2

ANSI No.

Roller W

Roller D

100 100-2 100-3 120 120-2 120-3 140 140-2 140-3 160 160-2 160-3 180 180-2 180-3 200 200-2 200-3 240 240-2

3/4 3/4 3/4 1 1 1 1 1 1 1-1/4 1-1/4 1-1/4 1-13/32 1-13/32 1-13/32 1-1/2 1-1/2 1-1/2 1-7/8 1-7/8

.750 .750 .750 .875 .875 .875 1.000 1.000 1.000 1.125 1.125 1.125 1.406 1.406 1.406 1.562 1.562 1.562 1.875 1.875

SPECIFICATION PAGES PT12-

SELECTION PAGES PT12-2

PT12-44

Cottered Riveted Average Inside Chain Chain Tensile Link Plate Width* Width* Strength Height 24000 1.61 1.73 1.187 48000 3.02 3.14 1.187 72000 4.43 4.56 1.187 34000 2.00 2.14 1.425 68000 3.79 3.93 1.425 102000 5.58 5.72 1.425 46000 2.14 2.31 1.662 92000 4.07 4.24 1.662 138000 6.00 6.16 1.662 58000 2.54 2.73 1.900 116000 4.85 5.04 1.900 174000 7.16 7.35 1.900 76000 2.88 3.15 2.137 152000 5.48 5.75 2.137 228000 8.07 8.34 2.137 95000 3.12 3.44 2.375 190000 5.94 6.26 2.375 285000 8.76 9.08 2.375 2.812 4.06 3.72 130000 2.812 7.52 7.18 260000

RELATE PRO UCTS PAGES PT12-40


This is particularly true with drives of long center distance. When the centers are fixed it is advisable to use an idler sprocket to provide the proper chain tension originally, and also to compensate for natural chain wear. Hardened Teeth–The advantages gained by hardening the teeth of the small sprocket easily offset the hardening cost. Longer life, increased strength, equalized wear between small and large sprockets–all result in lower overall cost to the chain drive user. Hardened steel sprockets are recom mended for use under the following conditions: 1. Slow speed, heavily loaded drives where chains and sprockets are selected on the basis of chain tensile strengths; 2. Moderate speed drives where sprockets have 17 teeth or less; 3. High speed drives where sprockets have 25 teeth or less; 4. When speed ratios exceed 4 to 1; 5. When drives are operating exposed to dirty or dusty surroundings.

Lubrication of Roller Chain Drives Lubrication of roller chains is essential for effectively minimizing metal-to-metal bearing contact of pin-bushing joints of the chain. Oil should be applied to outside plate and inside plate edges, since access to pin-bushing areas is possible only through clearances between the outside plates and the inside plates. Oil applied on the center line of rollers cannot reach pin-bushing joints. Chain drives should be protected against dirt and moisture and the oil supply kept free of contamination. Periodic oil change is desirable. A good grade of non-detergent petroleum base oil is recommended. Heavy oils and greases are generally too stiff to enter and fill the chain joints. The following table indicates the proper lubricant viscosity for various surrounding temperatures. For higher temperatures– consult factory. Table 41–Chain Lubrication Viscosity for Surrounding Temperatures Temperature Degrees F. 20 to 40 40 to 100 100 to 120 120 to 140

Recommended Lubricant SAE 20 SAE 30 SAE 40 SAE 50

The method of lubrication, which is governed by the speed of the chain and the amount of power transmitted, is indicated in the HP Rating Tables. Note that these are minimum lubrication requirements and the use of a better type FEATURES/BENEFITS PAGE PT12-2

(for example, Type 4 instead of Type 3) is acceptable and may be beneficial. The four basic types of lubrication indicated are described below. Type A–Manual Lubrication–Oil is applied periodically with a brush or spout can, preferably once every 8 hours of operation. Volume and frequency should be sufficient to prevent discoloration of lubricant in the chain joints. Type A–Drip Lubrication–Oil drops are directed be tween the link plate edges from a drip lubricator, Volume and frequency should be sufficient to prevent discoloration of lubricant in the chain joints. Precaution must be taken against misdirection of the drops by windage, Type B–Bath or Disc Lubrication–With bath lubrica tion the lower strand of chain runs through a sump of oil in the drive housing. The oil level should reach the pitch line of the chain at its lowest point while operating. With disc lubrication, the chain operates above the oil level. The disc picks up oil from the sump and deposits it onto the chain, usually by means of a trough. The diameter of the disc should be such as to produce rim speeds between 600 fpm minimum and 8000 fpm maximum. Type C–Oil Stream Lubrication–The lubricant is usually supplied by a circulating pump capable of supplying each chain drive with a continuous stream of oil. The oil should be applied inside the chain loop evenly across the chain width, and directed at the lower strand.

SPECIFICATION PAGES PT12-

SELECTION PAGES PT12-2

PT12-45

RELATE PRO UCTS PAGES PT12-40

DYNA-SYNC HT Synchrous Belts

Shaft Alignment–Shafts must be parallel. The use of a spirit level is recommended to make sure shafts are horizontal; then, if the distance between the shafts are equal on both sides of the drive, the shafts are parallel. Shafts, bearings and supporting structure should be suitable to maintain this alignment. Sprocket Location–Locate each sprocket as close as possible to a bearing. Sprocket Alignment–Sprockets must be aligned accurately. This can best be accomplished by checking with a straight edge along the finished sides of the sprockets as shown in the drawing. Chain Tension–Chains should be installed fairly tight with only a small amount of slack. In the case of vertical drives the chain should be kept snug. New chains will loosen up slightly as the joints seat themselves, causing initial elongation which is many times greater than the elongation during the balance of the chain life. After the first several weeks of operation it is advisable to adjust the centers, particularly on long center drives. After this initial elongation, with proper care and lubrication, roller chains will give long service without undue elongation or wear. Center Distance–It is desirable to provide some means of adjusting the center distance between sprockets.

Sprockets

Installation of Roller Chain Drives

Conveyor Components

Installation, Maintenance

Engineering

ENGINEERING/TECHNICAL


DYNA-SYNC

NOTES

HT Synchrous Belts Sprockets Conveyor Components Engineering FEATURES/BENEFITS PAGE PT12-2

SPECIFICATION PAGES PT12-

SELECTION PAGES PT12-2

PT12-46

RELATE PRO UCTS PAGES PT12-40


Conveyor Components

DYNA-SYNC

CONTENTS

Features/Benefits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT13-2 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT13-4

Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT13-8 Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT13-9 Selection/Dimensions

HT Synchrous Belts

How To Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT13-6

Spiral Wing Pulleys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT13-29 Shafting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT13-29 Engineered Class Pulleys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT13-30 Super Pulleys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT13-31 Dead Shaft Pulleys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT13-32 Elevator Pulleys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT13-32 Steel Split Pulleys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT13-33 Modifications/Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT13-35 Related Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT13-40

Conveyor Components

Heavy Duty Drum Pulley Weights . . . . . . . . . . . . . . . . . . . . . . . .PT13-18 Heavy Duty Wing Pulleys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT13-22 Heavy Duty Wing Pulley Weights . . . . . . . . . . . . . . . . . . . . . . . . .PT13-24 Mine Duty Xtra Drum & Wing Pulleys. . . . . . . . . . . . . . . . . . . . . .PT13-28

Sprockets

Drum and Wing Pulleys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT13-10 Heavy Duty Drum Pulleys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT13-15

Engineering/Technical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT13-43

Keyword Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INDEX-29

PT13-1

Engineering

Part Number Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INDEX-1


DYNA-SYNC

FEATURES/BENEFITS Today, the industrial marketplace demands quality products and services. DODGE has the experience and expertise to meet those demands from engineering support to on-time delivery. DODGE offers the broadest range of conveyor pulleys with a combination of the best resources for pulley manufacturing. The DODGE Conveyor Components Team is ready to provide you the best customer service in the industry.

HT Synchrous Belts

T-Section Super Pulley Lagged Drum Pulley Sprockets Conveyor Components

Wing Pulley

Engineering

Mine Duty Xtra Pulley

Steel Split Pulley

PT13-2


Conveyor Pulley Locking Devices

DYNA-SYNC

FEATURES/BENEFITS

HE Bushing/Hub • Most dependable mounting system for conveyor pulleys • Flange mount design • Easy installation/removal • Shaft diameters to 12” • Taper angle of 14° reduces axial movement along the shaft to tighten the bushing • Disc deflection and prestressing are greatly reduced

HT Synchrous Belts

• Specifically designed for drum and wing pulleys

Keyless Locking Devices • No axial movement during assembly • Shrink fit design assures a tight mechanical fit • Easy installation/removal

Sprockets

• High torque capability

Conveyor Components

• No keyway stress

Details for TAPER-LOCK Bushings – See page PT6-2

Engineering

Details for QD Bushings – See page PT6-15

PT13-3


DYNA-SYNC

SPECIFICATIONS Belt Conveyor Pulleys

HT Synchrous Belts

DODGE offers two standard designs that are stocked for quick delivery, CEMA duty (Conveyor Equipment Manufacturers Association), HE (High Endurance) welded hub and Mine Duty Extra HE integral hub construction. These are available with a plain surface and rubber lagged. HE bushings with 14 degree taper and 1/2 inch 60 diameter SBR rubber with herring bone groove lagging, are standard, stocked features. DODGE recommends pulley designs within the four classes of service detailed below. All of our designs strive for balance between cost and reliability. When possible, welds are avoided or eliminated to maintain the full strength of the base metal. Our welded designs rely upon the chemistry of the base metal, the type of weld and the geometry of the structure to achieve optimum post-weld performance as explained below. (Detailed descriptions of the four service classes are available in the Rockwell Automation publication, DODGE Global Conveyor Pulley Specifications & Technical Aspects, Selection and Applications.)

WARRANTY Sprockets Conveyor Components

• Class IV and III pulleys are conditionally warranted against defects in material and workmanship for one year of operation. A two-year warranty is available when loading information is provided. Note: Special Construction features listed at the top of page PT13-6 can be added to both Class IV and III pulleys to extend service life. Because these pulleys are made-to-order, they will require longer lead-time for shipment. The Special Construction modifications must be quoted at the time of inquiry and before order entry. • Class II and I pulleys are conditionally warranted against defects in material and workmanship for two years of operation because loading information must be provided.

CLASS IV DODGE Heavy Duty CEMA Standard drum pulleys use 14 degree taper welded hubs and bushings, and certified steel with special consideration for post weld strength with submerged arc welds. These pulleys meet or exceed all

requirements for steel drum pulleys established by CEMA and as detailed in ANSI standard number B105.1. The standard establishes load ratings and dimensions for use with fabric belts rated to 750 PIW (Pounds per Inch of belt Width).

CLASS III DODGE Mine Duty Extra pulleys use a proprietary 14 degree one piece integral hub to accept HE bushings. This eliminates the two welds of the hub into the end disc and delivers 100% of the capacity of the end disc steel. There is not a universal standard published for this class of service. The DODGE MDX design gives much higher safety factors than pulleys designed to meet the CEMA load ratings while fitting into the CEMA dimensions.

CLASS II DODGE Engineered pulleys utilize one-piece integral huband-end-discs and either HE 14 degree taper compression bushings or keyless locking devices. They are designed specifically to meet customer supplied load and tension ratings. This class is for fabric or steel cable conveyor belts rating to 2,499 PIW. These pulleys incorporate machined rims and laggings, static balance, stress relieving, magnetic particle and/or ultrasonic weld testing.

CLASS I DODGE Engineered pulleys with one piece “T” section machined end discs are continuously butt welded to the pulley rim for fabric or steel cable belts rated over 2,500 PIW up to the maximum available from belt manufactures, currently in excess of 10,000 PIW. These pulleys use keyless locking devices for shafts up to 30" in diameter. These pulleys incorporate machined rims and lagging, static balance, stress relieving, magnetic particle and/or ultrasonic weld testing. All Class I pulleys are manufactured within a 60 step documented Quality Assurance Process. Important Note: To Ensure You Get The Right Class Of Pulley For Your Application, Please Fill Out And Send In Form DMR 1477, Shown On Page PT13-9.

Engineering

Bushing and End Disc Constructions

CLASS IV FEATURES/BENEFITS PAGE PT13-2

CLASS III

MODIFICATIONS/ACCESSORIES PAGE PT13-35

CLASS II RELATED PRODUCTS PAGE PT13-40

PT13-4

CLASS I ENGINEERING/TECHNICAL PAGE PT13-43


Dodge Conveyor Design Program

INPUT

OUTPUT • Motor Horsepower • Belt Width (if not input) • Idler Angle (if not input) • Belt Speed (if not input) • Drive Pulley RPM • Belt Tensions (& take-up weight)

• Conveyor Capacity (tons per hour) • Length of Conveyor

• Pulley Diameters, Face Width & Shaft Diameter • Bearing Centers

• Lift of Conveyor

• Lagging

• Basic Conveyor Profile (7 main profiles) • Materials to be Moved

• Shaft Lengths

HT Synchrous Belts

The DODGE Computerized Conveyor Design Program selects DODGE/RELIANCE drive products for simple horizontal or uphill conveyors up to 2500 feet long, 800 feet lift, and 2500 tons per hour. The program operates with a minimum of input information and provides detailed design and product information as output. Input variables and output data are:

DYNA-SYNC

SPECIFICATIONS

• Bearing Diameter with L10 Life

• Belt Speed (not required, can be selected by program) • Belt Width (not required, can be selected by program)

• Backstop Requirement • DODGE Torque-Arm Reducers Selected Sprockets

• Idler Angle (not required, can be selected by program)

• Maximum Running Belt Tension (PIW)

Pulley Profiles Only the seven types of profiles shown are available for design program analysis.

Engineering

Conveyor Components

Rockwell Automation has a conveyor design program for selecting pulleys for conveyor profiles shown. For more information and License Agreement, call 864-297-4800 or FAX 864-281-2318.

FEATURES/BENEFITS PAGE PT13-2

MODIFICATIONS/ACCESSORIES PAGE PT13-35

RELATED PRODUCTS PAGE PT13-40

PT13-5

ENGINEERING/TECHNICAL PAGE PT13-43


DYNA-SYNC

HOW TO ORDER Standard, Stocked CEMA and Mine Duty Extra Pulleys The DODGE Global Pulley Specifications on page PT13-4 direct customers to one of the four service or application classes. If customers know their pulley description and the dodge catalog, they can order pulleys for Class IV (CEMA Standard) and Class III (Mine Duty Extra) by part number, bare or lagged, flat faced or taper crowned.

HT Synchrous Belts

However, the DODGE part number is often not known and the customer will inquire based upon pulley diameter, face width and hub size. CEMA standards for pulley face width are belt width + 2 inches up to 42 inch belts and belt width + 3 inch from 48 inch to 60 inch belts. Drum and wing pulley diameters are dependent upon belting and the shaft diameter required for the application. Availability from stock is best for standard CEMA dimensions.

PULLEY ASSEMBLIES One of the most popular services we offer is to package and assemble pulleys, shaft, bearings and coupling halves for shipment, ready to install on the customer's conveyor truss. However, to do this we must have accurate shaft dimensions and tolerances at the time of order entry. These determine the hub size of the pulley and the bearing size. Bearings are ordered from another DODGE plant. The pulley assembly process can be shortened by providing the shaft details outlined in form DMR 1446 (page PTPT13-7). Please note – all pulley assemblies are considered non-standard because of the variability of size and weight.

Special Construction Pulleys Sprockets

There are Special Construction specifications that can be stipulated by the customer to extend the service life of Class IV CEMA and Class III Mine Duty Extra pulleys, for demanding applications, or to meet special job requirements. If these modifications are required, the products will become Special Construction made-to-order and identified by order number. These nonstandard modifications must be documented and quoted at the time of inquiry and before order entry.

6. Keyless locking devices with dust covers vs standard HE 14-degree compression bushings 7. Post weld thermal stress relieving before machining 8. Magnetic particle and/or ultra sonic weld inspections 9. Static or dynamic balancing 10. Identification tags 11. Export or other special packaging ENGINEERED, MADE-TO-ORDER PULLEYS

Special Construction Features Include But Are Not Limited To: Conveyor Components

1. Rim and rubber lagging thickness 2. Lagging rubber material and durometer 3. Turning steel rims and/or rubber lagging to a specified total indicated run-out (TIR) 4. End disc steel thickness 5. Shaft material surface finish (RMS) and turndown radii

All DODGE heavy duty CEMA or Mine Duty Extra pulleys are designed to meet or exceed the CEMA steel pulley ANSI standard B105.1. However, for pulleys engineered to the customer's application loads and tensions, we require completion of the Engineered Pulley Data Sheet, DMR 1447 (page PT13-9). The selection process recommended by Rockwell Automation for DODGE conveyor pulley is covered on page PT13-10.

Engineering FEATURES/BENEFITS PAGE PT13-2

SELECTION/DIMENSIONSS PAGE PT13-10

MODIFICATIONS/ACCESSORIES PAGE PT13-35

PT13-6

ENGINEERING/TECHNICAL PAGE PT13-40


Pulley Assemblies To order shafting, please copy and complete the sketches shown below (DMR1446).

DYNA-SYNC

HOW TO ORDER

DRIVE PULLEY & SHAFT DIMENSIONS

“A” PULLEY DIA. – FACE WIDTH – HUB TYPE

HT Synchrous Belts

“B” ___________ ___________ ___________

BRG. CENTERS

SHAFT DIA. AT HUB – SHAFT DIA. AT BRG. – SHAFT DIA. AT “A” – SHAFT DIA. AT “B” – NUMBER OF KEYSEATS –

___________ ___________ ___________ ___________ ___________

KEYSEAT “A” – _____ X _____ X _____ LONG KEYSEAT “B” – _____ X _____ X _____ LONG DIRECTION OF ROTATION ____________ (LOOKING AT DRIVEN END)

LAGGING –

THICKNESS – ____________ TYPE – ____________

Sprockets

OVERALL SHAFT LENGTH

NON-DRIVE PULLEY & SHAFT DIMENSIONS

PULLEY DIA. – FACE WIDTH – HUB TYPE

Conveyor Components

DRUM – WING –

___________ ___________ ___________

BRG. CENTERS

SHAFT DIA. AT HUB – SHAFT DIA. AT BRG. –

FEATURES/BENEFITS PAGE PT13-2

___________ ___________

KEYSEAT – 0 _____ , 1 _____ , 2 _____

SELECTION/DIMENSIONSS PAGE PT13-10

MODIFICATIONS/ACCESSORIES PAGE PT13-35

PT13-7

ENGINEERING/TECHNICAL PAGE PT13-40

Engineering

OVERALL SHAFT LENGTH


DYNA-SYNC

NO ENC

T

E

Pulleys (QTY) Diameter X Face Width • Face Type • Hub Type & Size • Class (QTY) Lagging Thickness & Type (QTY) Bushing Size & Bore

HT Synchrous Belts

Diameter:

6”-60” (Other diameters available upon request)

Face Width:

12”-78” (Other face widths available upon request)

Face Type:

CR – Crown Face ST – Straight Face

Pulley Type:

DR – Drum WI – Wing

Hub Type & Size:

HE – (High Endurance) and Size (HE25) T-L – (TAPER-LOCK) QD – (Quick Disconnect) Keyless Locking

Class:

CEMA (Heavy Duty) MDX (Mine Duty Extra) MD (Mine Duty) ENG (engineered)

Lagging Thickness:

1/4”, 3/8”, 1/2”, 3/4”, 1” (Standard) Other Thickness Available on Request

Sprockets

Lagging Material & (Durometer): SBR (60/45/70), D-LAG (60), Neoprene (60/45/70), Ceramic, Holz Lagging Pattern:

Plain, Herringbone, Chevron, Diamond, Tuff-Top, Concentric, Parallel, Lorig Aligner

Bushing Size:

HE25 (Max. Bore 2-1/2”) F30 (Max. Bore 3,) E (Max. Bore 2-15/16”)

Examples:

1-12 x 26 CR DR HE25 MDX 3/8” Herringbone Lagging 2-HE25 x 2-7/16” Bushings

Conveyor Components

1-14 x 42 CR WI T-L F25 2-2517 x 2-7/16” TAPER-LOCK Bushings 1-16 x 44 ST DR QD F 2-F x 3-7/16” QD Bushings

Shafting Diameter X Length • # of Keyseats • # of Turndowns x Turndown Diameters Examples:

2-7/16” x 63" 3-7/16” x 84”, 3KS 3-15/16” x 76”, 3KS, 2TD X 3-7/16”

Engineering

NOTE: All shafts require a drawing which indicates the location of keyseats, length of turndowns, bearing centers, turndown radii and location of pulley on the shaft.

FEATURES/BENEFITS PAGE PT1 -2

O IFICATIONS/ACCESSORIES PAGE PT1 -

RELATE PRO UCTS PAGE PT1 -40

PT13-8

ENGINEERING/TECHNICAL PAGE PT1 -4


Engineered Pulley Data Sheet LIMITED WARRANTY: Rockwell Automation offers a 2-year limited warranty and a serialized name plate for all engineered pulleys designed to customer supplied loading information.

DYNA-SYNC

SELECTION

Selection of DODGE Conveyor Pulleys can be simplified by supplying the information in the Application Data Sheet provided below (DMR1447). DODGE can then engineer the correct pulleys or pulley assemblies for your application. Company Name __________________________________ Date ______________ By ______________

Project _____________________________________________________________________________ Conveyor Information – Belt:

[

] Fabric

Take-Up:

[

[

] Screw

Drive Motor:

] Steel [

] Gravity

[

] Other ______________________ Belt Width ____________ in. [

] Hyd.

[

] Other ____________________________

HT Synchrous Belts

Address ________________________________________________ Est. No. _____________________

HP _____________ Belt Speed ______________ FPM Capacity _______________ TPH

Center to Center Distance __________________________ Lift in Feet _____________________________ Pulley Data:

Sprockets

Conveyor Identification Pulley Location (Drive, Tail, etc.) Pulley Quantity Pulley Type (Drum or Wing) Diameter x Face Crown or Straight Lagging Thickness - Type of Grooves Conveyor Components

Shaft Diameter through Pulley Shaft Diameter through Bearing Shaft Diameter at Drive Shaft Length Number of Keyseats Drive Type (Sprocket, Coupling, Shaft Mount Reducer, etc.) Bearing Centers Arc of Contact ________° T1 ________ Lbs. Engineering

T2 ________ Lbs.

Special Requirements:

FEATURES/BENEFITS PAGE PT1 -2

O IFICATIONS/ACCESSORIES PAGE PT1 -

RELATE PRO UCTS PAGE PT1 -40

PT13-9

ENGINEERING/TECHNICAL PAGE PT1 -4


DYNA-SYNC

SELECTION Drum and Wing Pulleys - CEMA, MDX, Mine Duty Proper selection of pulley diameter, face width and shaft diameter can easily be determined if the following information is known: Belt Width (BW) Bearing Centers (BC) Arc of Belt Contact (∝) Tight Side Belt Tension (T1) (for drive pulleys only)*

HT Synchrous Belts

Slack Side Belt Tension (T2)*

A = Moment arm for pulley (inches) BC = Bearing centers (inches) D = Shaft diameter (inches) F = Face width P = Overhung load R = Resultant pulley load (pounds)

Sprockets

STEP 1

STEP 3

Determine Required Pulley Face Width

Determine Pulley Pounds Per Inch of Belt Width

From:

From:

F = BW + 2” (for BW 42” and under) F = BW + 3” (for BW over 42”)

Where: F = Pulley face width BW = Belt width

PIW = T1 ÷ BW (for drive pulleys) PIW = T2 ÷ BW (for non-drive pulleys)

Conveyor Components

Where: PIW = Pounds per inch of width value T1 = Tight side tension T2 = Slack side tension BW = Belt Width

Note: For replacement pulleys use face width of existing pulleys.

STEP 4

STEP 2 Determine Bearing Center Minus Face Dimension

Determine Minimum Pulley Diameter

From:

(Drum pulleys only) Determine minimum pulley diameter using PIW, arc of belt contact (∝) and Table 1. Reading across table from proper arc of contact select pulley diameter with PIW rating greater than actual PIW. Final pulley diameter may be greater than the diameter selected from Table 1 and must be greater than the belt manufacturer's recommended minimum diameter.

BCMF=BC-F

Where: BCMF = Bearing center minus face dimension F = Face width BC = Bearing centerline to centerline dimension Note: This selection guide is for conveyors with fabric belting. For other conveyor systems, consult factory for pulley selection.

Engineering

*Note: If belt tensions T1 and T2 are not known, see page for determination.

FEATURES/BENEFITS PAGE PT1 -2

(Wing pulleys only) Determine minimum pulley diameter using PIW and Table 2. Select pulley diameter with PIW rating greater than actual PIW. Final pulley diameter may be greater than the diameter selected from Table 2 and must be greater than the belt manufacturer's recommended minimum diameter.

O IFICATIONS/ACCESSORIES PAGE PT1 -

RELATE PRO UCTS PAGE PT1 -40

PT13-10

ENGINEERING/TECHNICAL PAGE PT1 -4


DYNA-SYNC

SELECTION Drum and Wing Pulleys TABLE 1 Use in STEP 4 to determine minimum pulley diameter for Drum Pulleys Only MAXIMUM BELT TENSION (Pounds Per Inch of Belt Width) 10

12

14

16

18

20

24

30

36

42

48

54

60

80 60 55 45 40 40 40 45 45 50 55 55 60 70 75 85 95 105 95 85 75 70 60 55

95 75 65 55 45 45 50 50 55 60 65 65 75 80 90 100 115 125 115 100 90 80 75 65

120 95 80 70 60 60 60 65 70 75 80 85 95 105 115 130 145 160 145 130 115 105 95 85

145 115 100 85 70 70 75 80 85 90 100 105 115 125 140 160 175 195 175 160 140 125 115 105

175 135 115 100 85 85 85 95 100 110 115 120 135 150 170 185 205 230 205 185 170 150 135 120

205 160 140 120 100 100 105 115 120 130 140 145 160 180 200 225 250 275 250 225 200 180 160 145

260 200 175 150 130 125 130 140 150 160 175 185 200 225 250 280 310 345 310 280 250 225 200 185

345 265 230 200 170 165 175 190 200 215 230 245 265 300 335 375 415 460 415 375 335 300 265 245

430 335 290 245 215 205 220 235 255 270 290 305 335 375 420 465 520 575 520 465 420 375 335 305

520 400 345 295 255 250 260 285 305 325 345 365 400 450 505 560 620 690 620 560 505 450 400 365

605 465 405 345 300 290 305 330 355 380 405 425 465 525 590 650 725 805 725 650 590 525 465 425

690 535 460 395 340 330 350 375 405 430 460 490 535 600 670 745 830 920 830 745 670 600 535 490

775 600 520 445 385 375 395 425 455 485 520 550 600 675 755 840 930 1035 930 840 755 675 600 550

STEP 6

Determine Pulley Resultant Load

Determine Shaft Diameter

Determine pulley resultant load from belt tensions and arc of contact.

Determine shaft diameter from Table 3. Go down the proper pulley face width column and across from the bearing center minus face value (if the correct value is not listed, interpolate or use the next higher value) until a load rating greater than the resultant load calculated in Step 5 is found. The proper shaft diameter is then read from the vertical shaft diameter column.

Resultant load is calculated by: R = 2 x T2 X sin (∝/2) (non-drive)* R = (T1 + T2) x sin (∝/2) (drive)* Where: R = Pulley resultant load T1 = Tight side tension T2 = Slack side tension ∝ = Arc of contact

TABLE 2

*Note: If non-drive pulley is on tight side of belt, substitute T1 for T2. Wing pulleys should not be used as drive pulleys.

Use in STEP 4 to determine minimum pulley diameter for Wing Pulleys only MAXIMUM BELT TENSION (Pounds Per Inch of Belt Width) Dia. 8” 10” 12” 14” 16”

FEATURES/BENEFITS PAGE PT1 -2

O IFICATIONS/ACCESSORIES PAGE PT1 -

Pounds Per Inch 80# 100# 120# 140# 160#

RELATE PRO UCTS PAGE PT1 -40

PT13-11

Dia. 18” 20” 24” 30” 36”

Pounds Per Inch 180# 200# 240# 280# 350#

ENGINEERING/TECHNICAL PAGE PT1 -4

Conveyor Components

STEP 5

Sprockets

8 65 50 45 35 30 30 30 35 35 40 45 45 50 55 60 70 75 85 75 70 60 55 50 45

HT Synchrous Belts

PULLEY DIAMETER (Inches)

Engineering

Arc of Contact (Deg.) 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240


DYNA-SYNC

SELECTION Drum and Wing Pulleys TABLE 133 – Use in Step 6 to determine shaft diameter LOAD RATINGS (POUNDS) FOR PULLEY AND SHAFT COMBINATIONS

HT Synchrous Belts Sprockets Conveyor Components Engineering

SHAFT (L) BEARING DIAMETER CENTERS (Inches) MINUS FACE 2 6 1-3/16 10 14 3 6 1-7/16 10 14 3 6 1-11/16 10 16 3 6 1-15/16 10 16 3 8 2-3/16 12 18 4 8 2-7/16 12 18 4 8 2-11/16 12 18 4 8 2-15/16 14 20 6 10 3-7/16 14 20 6 10 3-15/16 14 20 8 12 4-7/16 16 22 8 12 4-15/16 16 22 10 14 5-7/16 18 24

FEATURES/BENEFITS PAGE PT1 -2

PULLEY FACE WIDTH (inches) 12

14

16

18

20

22

26

32

38

44

51

57

63

66

1000 570 400 300 1500 1000 700 540 2400 1600 1100 780 3700 2500 1700 1200 5300 2900 2200 1500 6300 4000 3000 2100 8100 5300 3900 2800 10600 6900 4600 3400 11600 8500 6700 5100 16700 12400 9800 7500 19600 15300 12500 9800

920 520 370 280 1500 1000 700 540 2400 1600 1100 780 3700 2500 1700 1200 5300 2900 7200 1500 6300 4000 3000 2100 8100 5300 3900 2800 10600 6900 4600 3400 11600 8500 6700 5100 16700 12400 9800 7500 19600 15300 12500 9800 25200 19900 16400 13000

780 440 310 240 1400 950 660 510 2400 1600 1100 780 3700 2500 1700 1200 5300 2900 2200 1500 6300 4000 3000 2100 8100 5300 3900 2800 10600 6900 4600 3400 11600 8500 6700 5100 16700 12400 9800 7500 19600 15300 12500 9800 25200 19900 16400 13000 26600 22000 18700 15300

670 380 270 200 1200 820 570 440 2300 1600 1100 750 3700 2500 1700 1200 5300 2900 2200 1500 6300 4000 3000 2100 8100 5300 3900 2800 10600 6900 4600 3400 11600 8500 6700 5100 16700 12400 9800 7500 19600 15300 12500 9800 25200 19900 16400 13000 26600 22000 18700 15300

590 340 230 180 1100 720 500 390 2000 1400 960 660 3500 2400 1700 1100 5300 2900 2200 1500 6300 4000 3000 2100 8100 5300 3900 2800 10600 6900 4600 3400 11600 8500 6700 5100 16700 12400 9800 7500 19600 15300 12500 9800 25200 19900 16400 13000 26600 22000 18700 15300

530 300 210 160 950 640 450 350 1800 1200 850 590 3100 2100 1500 1000 5100 2800 2100 1500 6300 4000 3000 2100 8100 5300 3900 2800 10600 6900 4600 3400 11600 8500 6700 5100 16700 12400 9800 7500 19600 15300 12500 9800 25200 19900 16400 13000 26600 20000 18700 15300

440 250 170 130 790 530 370 290 1500 1000 700 490 2600 1800 1200 840 4200 2300 1700 1200 5600 3600 2700 1900 8100 5300 3900 2800 10600 6900 4600 3400 11600 8500 6700 5100 16700 12400 9800 7500 19600 15300 12500 9800 25200 19900 16400 13000 26600 22000 18700 15300

350 700 140 110 620 420 290 230 1200 800 560 380 2100 1400 970 670 3300 1900 1400 980 4400 2900 2100 1500 6400 4200 3100 2200 9100 6000 3900 2900 11600 8500 6700 5100 16700 12400 9800 7500 19600 15300 12500 9800 25200 19900 16400 13000 26600 22000 18700 15300

290 160 110 87 510 350 240 190 980 660 460 320 1700 1100 800 550 2800 1500 1100 810 3700 2400 1700 1300 5300 3400 2600 1800 7500 4900 3200 2400 10100 7400 5800 4400 16700 12400 9800 7500 19600 15300 12500 9800 25200 19900 16400 13000 26600 22000 18700 15300

240 140 96 74 440 300 210 160 830 560 390 270 1400 980 680 470 2400 1300 970 690 3100 2000 1500 1100 4500 2900 2200 1600 6400 4200 2800 2000 8500 6300 4900 3800 14200 10600 8400 6400 19100 14800 12100 9500 25200 19900 16400 13000 26600 22000 18700 15300

210 170 82 63 370 250 180 140 710 480 340 230 1200 840 580 400 2000 1100 820 590 2700 1700 1300 910 3800 2500 1900 1300 5500 3600 2300 1700 7200 5300 4200 3200 12000 8900 7100 5400 16100 12500 10300 8100 23600 18600 15400 12200 26600 22000 18700 15300

180 100 73 56 330 220 160 120 630 430 300 210 1100 740 520 360 1800 990 730 530 2400 1500 1100 810 3400 2200 1600 1200 4900 3200 2100 1600 6400 4700 3700 2800 10600 7900 6300 4800 14200 11100 9100 7100 20800 16400 13500 10700 25100 20700 17700 14500

170 94 66 51 300 200 140 110 570 380 270 180 990 670 470 320 1600 890 660 470 2100 1400 1000 130 3100 2000 1500 1100 4400 2900 1900 1400 5700 4200 3300 2500 9500 7100 5600 4300 12700 9900 8100 6400 18500 14600 12100 9600 22300 18400 15700 12800

160 90 63 48 290 190 130 100 540 370 260 180 940 640 420 310 1500 850 630 450 2000 1300 910 690 2900 1900 1400 1000 4200 4700 1800 1300 5500 4000 3200 2400 9000 6700 5300 4100 12100 9400 7700 6000 17600 13900 11500 9100 21100 17500 14900 12200

O IFICATIONS/ACCESSORIES PAGE PT1 -

RELATE PRO UCTS PAGE PT1 -40

PT13-12

ENGINEERING/TECHNICAL PAGE PT1 -4


DYNA-SYNC

SELECTION Drum and Wing Pulleys TABLE 3 (cont'd) – Use in Step 6 to determine shaft diameter LOAD RATINGS (POUNDS) FOR PULLEY AND SHAFT COMBINATIONS 16

18

20

22

26

32

38

44

51

57

63

66

35700 29500 25100 20600

35700 29500 25100 20600 39200 33200 28800 24000 49000 41400 35900 29900 54100 46500 40800 34400 65700 56400 49500 41800

35700 29500 25100 20600 39200 33200 28800 24000 49000 41400 35900 29900 54100 46500 40800 34400 65700 56400 49500 41800

35700 29500 25100 20600 39200 33200 28800 24000 49000 41400 35900 20000 54100 46500 40800 34400 65700 56400 49500 41800 67700 59400 52900 45400 80400 70500 59500 51500 94500 78100 66500 57900 110000 91100 77600 64800

35700 29500 25100 20600 39200 33200 28800 24000 49000 41400 35900 29900 54100 48500 40800 34400 65700 56400 49500 41800 67700 59400 52900 45400 80400 70500 59500 51500 94500 78100 66500 57900 110000 91100 77600 64800

35700 29500 25100 20600 39200 33200 28800 24000 49000 41400 35900 29900 54100 48500 40800 34400 65700 56400 49500 41800 67700 59400 52900 45400 80400 70500 59500 51500 94500 78100 66500 57900 110000 91100 77600 64800

35700 29500 25100 20600 39200 33200 28800 24000 49000 41400 35900 29900 54100 46500 40800 34400 65700 56400 49500 41800 67700 59400 52900 45400 80400 70500 59500 51500 94500 78100 66500 57900 110000 91100 77600 64800

35700 29500 25100 20600 39200 33200 28800 24000 49000 41400 35900 29900 54100 46500 40800 34400 65700 56400 49500 41800 67700 59400 52900 45400 80400 70500 59500 51500 94500 78100 66500 57900 110000 91100 77600 64800

35700 29500 25100 20600 39200 33200 28800 24000 49000 41400 35900 29900 54100 46500 40800 34400 65700 56400 49500 41800 67700 59400 52900 45400 80400 70500 59500 51500 94500 78100 66500 57900 110000 91100 77600 64800

35700 29500 25100 20600 39200 33200 28800 24000 49000 41400 35900 29900 54100 46500 40800 34400 65700 56400 49500 41800 67700 59400 52900 45400 80400 70500 59500 51500 94500 78100 66500 57900 110000 91100 77600 64800

33100 27300 23300 19000 39200 33200 28800 24000 49000 41400 35900 29900 54100 46500 40800 34400 65700 56400 49500 41800 67700 59400 52900 45400 80400 70500 59500 51500 94500 78100 66500 57900 110000 91100 77600 64800

31300 25900 22100 19000 38000 32100 27800 23200 49000 41400 35900 29900 54100 46500 40800 34400 65700 56400 49500 41800 67700 59400 52900 45400 80400 70500 59500 51500 94500 78100 66500 57900 110000 91100 77600 64800

Sprockets

14

Conveyor Components

12

HT Synchrous Belts

PULLEY FACE WIDTH (inches)

Engineering

SHAFT (L) BEARING DIAMETER CENTERS (Inches) MINUS FACE 10 14 6 18 24 12 16 6-1/2 20 26 12 16 7 20 26 14 18 7-1/2 22 28 14 18 8 22 28 16 20 8-1/2 24 30 16 20 9 26 32 16 22 9-1/2 28 34 16 22 10 28 34

FEATURES/BENEFITS PAGE PT1 -2

O IFICATIONS/ACCESSORIES PAGE PT1 -

RELATE PRO UCTS PAGE PT1 -40

PT13-13

ENGINEERING/TECHNICAL PAGE PT1 -4


DYNA-SYNC

SELECTION Drum and Wing Pulleys STEP 7 Determine Drive Pulley Shaft Diameter (For drive pulleys only) The shaft diameter determined in Step 6 must be checked for torque capacity. The shaft diameter required for torque is determined from:

HT Synchrous Belts

16 x √(KB x A x R ÷ 2)2 + [(T1 – T2) x D ÷ 2]2 πxS Where: DT = Required shaft diameter from torque π = 3.1416 S = 8000 psi for 1042 -1045 shafting (10,000 for 4140) KB = 1.5* A = Moment arm (from Table 4) R = Resultant load from Step 5 T1 = Tight side tension T2 = Slack side tension D = Pulley Diameter *Note: Use KB = 2.5 for overhung load drive (chain, torque arm, etc.) If DT is greater than the shaft diameter from Step 6, round DT up to the next standard shaft diameter and use that value. If DT is less than the shaft diameter from Step 6, use the diameter selected from Step 6. Table 4 – A-Values DT = 3

Sprockets

Shaft Dia. (inches) 1 to 2-7/16 2-11/16 to 2-15/16 3-7/16 3-15/16 4-7/16

A N+1-5/8 N+1-3/4 N+2-1/2 N+2-3/4 N+3

Shaft Dia. (inches) 4-15/16 5-7/16 to 6 6-1/2 to 7 7-1/2 to 8 8-1/2 to 10

A N+3-1/4 N+4-1/2 N+5 N+5-1/4 N+6-1/4

N = BCMF÷2

STEP 8 Conveyor Components Engineering

Compare Pulley Diameter Compare the pulley diameter, face width combination selected with the standard drum pulley listing on pages PT13-15 - PT13-21 or the standard wing pulley listing on pages PT13-22 - PT13-27 to insure the selected combination is available. If the selected combination is not available increase shaft diameter or pulley diameter until a standard pulley is listed. Example 1 (Drive Pulley) Given: 36” belt width 3600 lb. T1 52” bearing centers 1600 lb. T2 210° arc of contact Step 1 Determine required face width from: F=BW+2” F=36+2=38 Step 2 Determine bearing center minus face dimension from: BCMF= BC-F BCMF=52-38= 14” Step 3 Determine pounds per inch of face width from: PIW=T1÷BW PIW=3600÷36=100 PIW Step 4 Determine minimum pulley diameter using Table 1. Since PIW = 100 and arc of contact is 210°, the minimum pulley diameter is 14”. FEATURES/BENEFITS PAGE PT1 -2

Step 5 Determine resultant load from: R=(T1 + T2) x sin (∝/2) R=(3600 + 1600) x sin (210/2)=5023 lb. Step 6 Determine shaft diameter using Table 3. Using a face width of 38” bearing center minus face dimension of 14” and a pulley resultant load of 5023 lbs., read down the 38” face width column until the load rating at BCMF = 14” exceeds 5023 lb. The first value to exceed 5023 lbs. is 5800 lbs. at a shaft diameter of 3-7/16. Step 7 Check torque capacity of selected shaft using: DT = 3 DT = 3

16 x √(KB x A x R ÷ 2)2 + [(T1 – T2) x D ÷ 2]2 πxS

16 x √(1.5 x 9.5 x 5023 ÷ 2)2 + [(3600 – 1600) x D ÷ 2]2 3.1416 x 8000

DT = 2.86” The 3-7/16 shaft diameter selected in Step 6 is greater than 2.86: therefore 3-7/16 is the final shaft diameter selection. Step 8 Checking the standard pulley listing on page PT13-18, a 14 x 38 pulley with 3-7/16 shaft (HE35 Hub) is a standard pulley. Example 2 (Non-drive wing pulley). Given: 54” belt width 1805 arc of contact 71 bearing centers 8600 lb. T2 Step 1 Determine required face width from: F = BW + 3, F = 54 + 3 = 57, Step 2 Determine bearing center minus face dimension from: BCMF=BC-F BCMF=71 -57=14, Step 3 Determine pounds per inch of face width from: PIW=T2÷BW PIW=8600÷54=159 PIW Step 4 Determine minimum pulley diameter using Table 2. Since PIW = 159 the minimum pulley diameter is 16”. Step 5 Determine resultant load from: R=2 x T2 x sin (∝/2) R = 2 x 8600 x sin (180/2) = 17,200 lbs. Step 6 Determine shaft diameter using Table 3. Using a face width of 57”, bearing center minus face dimension of 14” and a pulley resultant load of 17,200 lbs., read down the 57” face width column until the load rating at BCMF = 14” exceeds 17,200 lbs. The first value to exceed 17,200 lbs. is 20,700 lbs. at a shaft diameter of 5-7/16. Step 7 Checking the standard wing pulley listing on page PT13-24, a 16 x 57 wing pulley with 5-7/16 shaft (HE60 hub) is a standard pulley.

O IFICATIONS/ACCESSORIES PAGE PT1 -

RELATE PRO UCTS PAGE PT1 -40

PT13-14

ENGINEERING/TECHNICAL PAGE PT1 -4


DYNA-SYNC

SELECTION/DIMENSIONS HE Heavy Duty Drum Pulleys • HE mounting system designed specifically for conveyor pulleys • Most dependable mounting system for conveyor pulleys • Flange mount design • Designed to CEMA specifications • One piece die formed through 30” • Diameters to 60”, face widths exceeding 78” • Available from stock

HE Dimensions A

B

Bushing

Max. Bore

HE25 HE30 HE35 HE40 HE45 HE50 HE60 HE70 HE80 HE100 HE120

3/4 3/4 3/4 3/4 3/4 3/4 1 1 1-1/4 1-1/4 1-1/4

2-1/4 2-3/4 3 3-1/2 4 4-1/2 5-1/4 6-1/4 7 9 10

HE25 HE30 HE35 HE40 HE45 HE50 HE60 HE70 HE80 HE100 HE120

2-1/2 3 3-1/2 4 4-1/2 5 6 7 8 10 12

Screw Torque (in.-lb.) 360 710 1080 1680 1680 2400 4200 6000 6000 7200 7200

A

Engineering

Conveyor Components

Hub

Sprockets

HT Synchrous Belts

• Standard crown face or straight face available

FEATURES/BENEFITS PAGE PT13-2

MODIFICATIONS/ACCESSORIES PAGE PT13-35

RELATED PRODUCTS PAGE PT13-40

PT13-15

ENGINEERING/TECHNICAL PAGE PT13-43


DYNA-SYNC

SELECTION HE Heavy Duty Drum Pulley Part Numbers Dia. Hub 6 8 10 12

HT Synchrous Belts

14

16

18

Sprockets

20

24

30

12 14 16 18 20 HE25 206001 206003 203500 203501 HE25 206020 206022 206024 203516 HE25 206035 206039 206041 HE30 HE25 209716 206056 206057 206058 206060 HE30 HE35 HE25 203594 209726 206080 HE30 209727 HE35 HE40 209725 HE25 203651 206091 206092 HE30 209734 209775 HE35 HE40 HE25 206110 HE30 209745 HE35 HE40 HE45 HE25 209756 206125 HE30 209757 HE35 HE40 HE30 203815 HE35 HE40 HE45 HE50 HE35 HE40 209780

FACE WIDTH 22 24 26 30 206009 203502 206012 203503 206029 203519 206042 203530 206044 203533 209718 203561 206063 209720 206064 203565 206081 209730 206082

32 36 38 40 44 51 203504 203505 206014 203511 206031 206032 206033 206034 206046 206048 206049 206052 203538 203543 206051 206050 206066 206069 206072 206074 206067 206070 209722 206073 203587 203571 203577 203581 203588 206083 206084 203633 203642 203620 206085 203907 206087 203629 203634 203643 203630 203644 209736 206095 209749 206097 206099 203685 203695 209737 206096 206098 206100 206102 203696 203666 203674 203682 203686 206103 203675 203683 203687 206104 209746 206111 206114 206116 206112 206115 206117 203745 203756 206113 203729 206118 209751 206121 203757 203730 203740 206119 203746 206120 203741 209752 203758 206126 206089 206131 209758 206127 206129 206132 206134 203807 206128 206130 206133 206135 203808 209759 203790 203797 206136 203809 206140 206142 206145 206148 203848 206141 206143 206146 206149 203849 203908 206144 206147 203844 203850 203836 203841 206150 206151 203343 209742 209776 203879 203880 203888 209741

Note: All stock pulleys are crown face. Conveyor Components

HE Heavy Duty Lagged Drum Pulley Part Numbers Dia.

Hub

12 14

HE30 HE25 HE25 HE30 HE35 HE30 HE35 HE30 HE40 HE35 HE40 HE45

16 18 20 Engineering

24

Lagging 3/8 HBG 3/8 HBG 3/8 HBG 3/8 HBG 3/8 HBG 3/8 HBG 3/8 HBG 3/8 HBG 3/8 HBG 3/8 HBG 3/8 HBG 3/8 HBG

FEATURES/BENEFITS PAGE PT1 -2

26 206105 207954 207206 207207 206054 207211 206107 206078 207977 207978 206017

FACE WIDTH 32 38 206106 209907 207950 207951 207209 207208 207210 206075 206076 207212 207213 206077 206108 207214 209934 206079 206088 209938 209939 207215 207216 206018 206019

O IFICATIONS/ACCESSORIES PAGE PT1 -

RELATE PRO UCTS PAGE PT1 -40

PT13-16

44 209909 207205

51 209910 207952

209922

209923

209927

209940 206053

209941

ENGINEERING/TECHNICAL PAGE PT1 -4


TAPER-LOCK Heavy Duty Drum Pulleys

HT Synchrous Belts

• Flush mount, compact design mounting system • Designed to CEMA specifications • Standard crown face or straight face available • One piece die formed through 30” • Diameters to 60”, face widths exceeding 78” • Available from stock

TAPER-LOCK Dimensions A

B

Bushing

Max. Bore

K25 F25 F30 K35 K40 K45 K50 K60 K70 K80 K100 K120

1 1 1 1 1 1 1 2-1/4 2-1/4 2-1/4 2-1/4 2-1/4

1-3/4 1-3/4 2 3-1/2 4 4-1/2 5 5 6 6-1/2 8-1/2 10

2517 2517 3020 3535 4040 4545 5050 6050 7060 8065 10085 120100

2-1/2 2-1/2 3 3-1/12 4 4-1/2 5 6 7 8 10 12

Screw Torque (in.-lb.) 430 430 800 1000 1700 2450 3100 7820 7820 7820 13700 13700

A

F25 and F30

Sprockets

Hub

DYNA-SYNC

SELECTION/DIMENSIONS

A

K25 through K120

QD Heavy Duty Drum Pulleys • Flange mount bushing system

• One piece die formed through 30” • Diameters to 60”, face widths exceeding 78” • Available from stock

QD Dimensions QD Hub

A

B

Bushing

Max. Bore

SF E F JS MS NS PS WS SS ZS

7/8 1 1-1/16 1-1/8 1-1/4 1-5/16 1-3/8 1-9/16 1-5/8 1-9/16

2-1/16 2-3/4 3-3/4 3-3/8 4-13/16 6 6-1/2 7-1/4 8-3/4 8-3/4

SF E F J M N P W S Z

2-7/16 2-15/16 3-7/16 3-15/16 4-7/16 4-15/16 6 8 10 12

FEATURES/BENEFITS PAGE PT13-2

Screw Torque (in.-lb.) 360 720 900 1620 2700 3600 5400 7200 9000 7200

MODIFICATIONS/ACCESSORIES PAGE PT13-35

A

RELATED PRODUCTS PAGE PT13-40

PT13-17

ENGINEERING/TECHNICAL PAGE PT13-43

Engineering

• Standard crown face or straight face available

Conveyor Components

• Designed to CEMA specifications


DYNA-SYNC

SELECTION Heavy Duty Drum Pulley Average Weights – HE, TAPER-LOCK, QD Dia. 6 8 10 12

HT Synchrous Belts

14

16

18

Sprockets

20

24 Conveyor Components

30

Max. Bore 2.5 2.5 2.5 3 2.5 3 3.5 2.5 3 3.5 4 2.5 3 3.5 4 4.5 2.5 3 3.5 4 4.5 5 2.5 3 3.5 4 4.5 5 3 3.5 4 4.5 5 6 3 3.5 4 4.5 5 6 7 8

12 27 34 43 49 52 60 75 62 62 85 95 67 72 90 106 ... 77 90 100 123 ... ... 101 117 125 135 ... ... 149 167 177 ... ... ... 204 222 253 ... ... ... ... ...

14 29 37 46 53 56 64 79 67 67 90 100 72 77 96 112 126 83 97 107 131 145 ... 111 127 134 144 159 ... 160 179 188 202 ... ... 218 236 270 284 ... ... ... ...

16 31 40 50 56 60 68 83 72 72 95 105 78 83 101 117 131 89 103 113 139 154 192 120 136 144 154 168 207 171 190 199 213 274 ... 232 250 287 301 340 ... ... ...

18 33 42 53 60 64 72 87 77 77 100 110 83 88 107 123 137 96 109 119 148 162 201 129 145 153 163 177 216 183 201 211 224 287 386 246 264 305 319 357 462 536 ...

20 35 45 56 63 69 77 92 82 82 105 114 89 94 112 129 142 102 115 125 156 170 209 138 154 162 172 186 225 194 212 222 235 301 403 260 278 344 336 374 483 557 613

Face Width 22 37 48 60 67 73 81 96 87 86 110 119 94 99 118 134 148 108 122 132 164 179 217 148 164 171 181 196 234 205 223 233 247 315 419 274 292 340 353 392 504 578 634

24 39 51 63 70 77 85 100 91 91 114 124 100 105 124 140 153 114 128 138 173 187 226 157 173 181 191 205 244 216 234 244 258 329 436 288 306 357 371 409 524 598 655

26 41 53 67 74 81 89 104 96 96 119 129 105 111 129 145 159 121 134 144 181 193 234 166 182 190 200 214 253 227 245 255 269 343 453 301 320 374 388 427 545 619 676

30 45 59 74 80 89 97 112 106 106 129 139 117 122 140 156 170 133 147 157 198 212 251 185 201 208 218 233 271 249 268 277 291 371 486 329 348 409 423 461 587 703 758

32 47 62 77 84 93 102 116 111 111 134 144 122 127 146 162 176 139 153 163 206 220 259 194 210 218 228 242 281 260 279 288 302 385 502 343 362 426 440 479 608 724 779

36 52 69 88 94 107 115 129 128 128 150 160 144 148 166 182 195 165 178 188 235 248 286 229 245 252 261 275 313 307 325 334 347 434 561 409 427 498 512 550 693 765 820

• Crown face pulleys will be provided unless straight face is specified • These pulleys are designed to meet the CEMA Pulley Specification B105.1–1993. They are not to be used with steel cable belts or other high modulus belts. Engineering FEATURES/BENEFITS PAGE PT1 -2

SELECTION/ I ENSIONS PAGE PT1 -10

O IFICATIONS/ACCESSORIES PAGE PT1 -

PT13-18

ENGINEERING/TECHNICAL PAGE PT1 -4


44 60 80 101 108 124 135 146 148 162 170 179 166 190 189 204 217 190 212 213 268 281 320 266 282 289 298 312 350 351 369 378 391 490 627 465 483 568 581 619 777 849 904

46 62 83 105 111 128 139 150 153 166 175 184 171 196 194 210 223 197 218 219 276 290 350 275 291 298 308 321 360 362 380 389 403 504 644 479 497 585 599 637 797 869 925

51 67 90 113 120 138 149 161 165 179 187 196 185 210 214 224 237 212 234 243 297 311 371 299 314 321 331 344 383 390 408 417 430 538 685 514 532 629 642 680 849 921 977

54 71 96 122 128 150 160 171 180 193 201 210 204 228 232 241 254 235 256 265 321 334 394 329 344 351 360 373 411 431 448 457 470 581 735 573 590 692 705 742 925 995 1049

60 77 104 132 138 163 173 184 194 208 216 224 221 245 249 257 270 254 275 284 346 359 419 357 372 379 388 401 439 464 482 490 503 623 785 615 632 744 757 794 987 1057 1111

63 80 108 138 143 169 179 190 202 215 223 231 229 253 257 266 279 263 284 293 359 372 431 371 386 393 402 415 452 481 498 507 520 643 810 636 653 770 783 820 1018 1088 1142

66 83 112 143 149 175 185 196 209 222 230 239 237 261 266 274 287 273 294 303 371 384 444 385 400 406 415 429 466 497 515 524 536 664 834 657 674 796 809 847 1049 1120 1174

72 90 122 157 162 193 203 213 231 244 252 260 264 288 292 300 312 305 325 334 408 421 480 429 444 450 458 471 508 555 572 580 592 728 909 737 754 886 898 935 1156 1182 1236

75 93 127 162 167 199 209 220 239 251 259 267 273 296 300 308 320 314 335 343 421 433 492 443 457 464 472 485 522 571 589 597 609 749 934 757 775 912 924 961 1187 1213 1267

78 96 131 167 172 205 215 226 246 259 266 274 281 305 308 316 329 323 334 353 433 446 504 457 471 478 486 499 536 588 605 613 626 769 959 778 796 938 950 987 1218 1287 1339

DYNA-SYNC

Face Width 57 74 100 127 133 156 167 178 187 200 208 217 212 236 241 249 262 244 266 275 334 347 406 343 358 365 374 387 425 447 465 473 486 602 760 594 611 718 731 768 956 1026 1080

HT Synchrous Belts

40 56 75 94 101 116 123 138 138 137 160 169 155 159 177 193 206 178 191 200 251 265 303 248 263 270 280 294 332 329 347 356 369 462 594 437 455 533 547 584 735 807 862

Engineering

38 54 72 91 97 111 119 134 133 133 155 164 149 154 172 187 201 172 185 194 243 256 295 238 254 261 271 284 323 318 336 345 358 448 577 423 441 516 529 567 714 786 841

Sprockets

Heavy Duty Drum Pulley Average Weights – HE, TAPER-LOCK, QD

Conveyor Components

SELECTION

FEATURES/BENEFITS PAGE PT1 -2

SELECTION/ I ENSIONS PAGE PT1 -10

O IFICATIONS/ACCESSORIES PAGE PT1 -

PT13-19

ENGINEERING/TECHNICAL PAGE PT1 -4


DYNA-SYNC

SELECTION Heavy Duty Drum Pulley Average Weights – HE, TAPER-LOCK, QD Dia.

36 HT Synchrous Belts

42

48 Sprockets 54

Conveyor Components

60

Max. Bore 3 .5 4 4.5 5 6 7 8 10 3.5 4 4.5 5 6 7 8 10 4 4.5 5 6 7 8 10 4.5 5 6 7 8 10 4.5 5 6 7 8 10

12 292 310 320 ... ... ... ... ... ... 386 475 ... ... ... ... ... ... 579 ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ...

14 313 331 341 355 ... ... ... ... ... 411 504 468 ... ... ... ... ... 613 626 ... ... ... ... ... 745 ... ... ... ... ... 1283 ... ... ... ... ...

16 334 352 362 376 447 ... ... ... ... 435 534 497 536 ... ... ... ... 646 660 698 ... ... ... ... 783 821 ... ... ... ... 1338 1375 ... ... ... ...

18 355 373 383 397 472 546 620 ... ... 459 563 527 565 686 846 ... ... 680 693 731 803 976 ... ... 821 859 1124 ... ... ... 1394 1431 1497 1567 ... ...

20 376 394 404 417 497 571 645 702 ... 484 592 556 594 716 885 941 ... 713 727 765 837 1020 1076 ... 859 897 1174 1246 1301 ... 1450 1847 1552 1622 1676 ...

Face Width 22 397 415 425 438 522 596 670 727 ... 508 621 585 623 745 924 980 ... 747 760 798 870 1065 1120 ... 896 934 1124 1296 1351 ... 1506 1543 1608 1678 1732 ...

24 417 436 445 459 547 621 695 752 1221 533 651 614 653 774 963 1018 1398 780 794 832 904 1109 1165 1592 934 972 1274 1346 1401 1803 1561 1598 1664 1734 1788 2030

26 438 457 466 480 572 646 720 777 1254 557 680 644 682 803 1002 1057 1437 814 827 865 937 1154 1209 1636 972 1010 1324 1396 1451 1853 1617 1654 1720 1790 1844 2086

30 480 498 508 522 622 697 836 891 1321 606 738 702 740 862 1195 1249 1515 881 894 932 1004 1398 1452 1725 1047 1085 1425 1697 1750 1953 1729 1765 1831 2151 2204 2198

32 501 519 529 543 647 722 861 916 1423 630 768 731 770 891 1234 1288 1657 914 928 966 1038 1442 1497 1913 1085 1123 1475 1747 1800 2191 1784 1821 1887 2207 2259 2491

36 617 635 644 657 769 839 911 966 1490 780 926 889 927 1044 1312 1366 1735 1113 1126 1163 1231 1531 1586 2002 1327 1364 1777 1847 1901 2291 2155 2191 2251 2319 2371 2602

• Crown face pulleys will be provided unless straight face is specified • These pulleys are designed to meet the CEMA Pulley Specification B105.1–1993. They are not to be used with steel cable belts or other high modulus belts.

Engineering FEATURES/BENEFITS PAGE PT1 -2

SELECTION/ I ENSIONS PAGE PT1 -10

O IFICATIONS/ACCESSORIES PAGE PT1 -

PT13-20

ENGINEERING/TECHNICAL PAGE PT1 -4


44 701 718 727 740 869 939 1011 1066 1623 878 1043 1006 1044 1161 1467 1521 1890 1247 1259 1297 1364 1709 1764 2180 1478 1515 1978 2048 2101 2492 2378 2414 2474 2541 2594 2825

46 721 739 748 797 894 964 1036 1091 1656 902 1073 1085 1073 1190 1506 1560 1929 1280 1293 1330 1398 1754 1808 2224 1515 1553 2028 2098 2151 2542 2433 2469 2529 2597 2650 2881

51 774 791 800 850 957 1206 1099 1154 1739 1014 1046 1158 1146 1263 1603 1658 2026 1364 1377 1414 1462 1865 1919 2335 1610 1647 2153 2223 2277 2667 2573 2609 2669 2737 2789 3021

54 879 896 905 953 1066 1131 1201 1255 1858 1151 1290 1302 1289 1402 1777 1830 2188 1546 1558 1595 1658 2087 2140 2545 1833 1870 2431 2498 2550 2930 2915 2950 3005 3070 3121 3342

60 942 959 967 1016 1141 1206 1276 1330 1958 1225 1377 1390 1377 1490 1894 1947 2304 1646 1658 1695 1758 2221 2273 2679 1946 1983 2581 2649 2701 3080 3082 3117 3172 3238 3288 3509

63 973 990 999 1047 1178 1244 1314 1368 2008 1261 1421 1433 1421 1533 1952 2005 2362 1696 1709 1745 1808 2287 2340 2745 2003 2039 2656 2724 2776 3155 3166 3201 3256 3321 3372 3593

66 1004 1022 1030 1078 1216 1281 1351 1405 2058 1298 1465 1477 1464 1577 2011 2063 2421 1747 1759 1795 1859 2354 2407 2812 2059 2096 2732 2799 2851 3231 3249 3285 3339 3405 3456 3676

72 1141 1158 1165 1213 1362 1423 1427 1480 2157 1472 1653 1665 1651 1760 2127 2180 2538 1979 1990 2026 2085 2468 2540 2946 2339 2375 3084 2949 3001 3381 3675 3710 3759 3572 3623 3844

75 1173 1189 1197 1245 1400 1461 1464 1518 2207 1509 1697 1708 1696 1803 2186 2238 2596 2029 2040 2076 2135 2554 2607 3012 2396 2431 3160 3024 3077 3456 3759 3793 3843 3656 3707 3927

78 1204 1221 1228 1276 1437 1499 1567 1620 2326 1545 1741 1752 1739 1847 2360 2411 2758 2079 2091 2126 2186 2777 2828 3222 2452 2468 3235 3350 3550 3719 3843 3877 3926 3989 4039 4249

DYNA-SYNC

Face Width 57 910 928 936 984 1103 1169 1239 1293 1908 1188 1334 1346 1333 1446 1836 1888 2246 1596 1608 1645 1708 2154 2207 2612 1890 1926 2506 2573 2625 3005 2999 3034 3089 3154 3205 3426

HT Synchrous Belts

40 659 676 685 699 819 889 961 1016 1556 829 985 946 985 1103 1389 1444 1812 1180 1193 1230 1298 1620 1675 2091 1402 1440 1878 1947 2001 2391 2266 2302 2362 2430 2482 2714

Engineering

38 638 656 665 678 794 864 936 991 1523 805 956 919 956 1073 1351 1405 1773 1146 1159 1196 1264 1576 1630 2046 1365 1402 1827 1897 1951 2341 2210 2246 2306 2374 2427 2658

Sprockets

Heavy Duty Drum Pulley Average Weights – HE, TAPER-LOCK, QD

Conveyor Components

SELECTION

FEATURES/BENEFITS PAGE PT1 -2

SELECTION/ I ENSIONS PAGE PT1 -10

O IFICATIONS/ACCESSORIES PAGE PT1 -

PT13-21

ENGINEERING/TECHNICAL PAGE PT1 -4


DYNA-SYNC

SELECTION/DIMENSIONS HE Heavy Duty Wing Pulleys • HE mounting system designed specifically for conveyor pulleys • Most dependable mounting system for conveyor pulleys • Designed to CEMA specifications • Standard crown face or straight face available • Diameters to 60”, face widths exceeding 78”

HT Synchrous Belts

• Available with replaceable WING-LAG • Available from stock

HE Dimensions

Sprockets

Hub

A

B

Bushing

Max. Bore

HE25 HE30 HE35 HE40 HE45 HE50 HE60 HE70 HE80

1 3/4 3/4 3/4 3/4 3/4 1 1 1-1/4

2-1/4 2-3/4 3 3-1/2 4 4-1/2 5-1/4 6-1/4 7

HE25 HE30 HE35 HE40 HE45 HE50 HE60 HE70 HE80

2-1/2 3 3-1/2 4 4-1/2 5 6 7 8

Screw Torque (in.-lb.) 360 720 1080 1680 1680 2400 4200 6000 6000

A

HE Heavy Duty Wing Pulley Part Numbers Dia. 8 Conveyor Components

10 12 14 16

18

20 Engineering

24

Hub HE25 HE25 HE30 HE25 HE30 HE25 HE30 HE25 HE30 HE35 HE25 HE30 HE35 HE40 HE25 HE30 HE35 HE40 HE30 HE35 HE40

20 206196 206200

26 206199 206201

206205

206206 206212 206216 206387 206221 206222

206220

206231 206232

206240 206241

206447

FACE WIDTH 32 38 206213 206214 206202 206203 207566 206207 206208 206374 206209 206217 206218 206389 206392 206223 206225 206224 206226 206227 206233 206235 206234 206236 207402 206485 207569 206242 206334 207407 206243 206495 207572 206448 206245 206246 206527

44

51

206253 207567 206210 206211 206277 206394 206303 206408 206480 206320 206423 206487 207570 206336 206437 206497 207408

207418 207568 206264 206378 206278 206395

206247 206528

206410 206482

207571

206499 207410

206530

Note: All stock pulleys are crown face. FEATURES/BENEFITS PAGE PT13-2

MODIFICATIONS/ACCESSORIES PAGE PT13-35

RELATED PRODUCTS PAGE PT13-40

PT13-22

ENGINEERING/TECHNICAL PAGE PT13-43


• Flush mount, compact design mounting system • Designed to CEMA specifications • Standard crown face or straight face available • Diameters to 60”, face widths exceeding 78” • Available with replaceable WING-LAG • Available from stock

TAPER-LOCK Dimensions A

B

Bushing

Max. Bore

W16 W25 K30 K35 K40 K45 K50 K60 K70 K80

1-5/8 1-1/2 1-3/4 2-3/4 2-3/4 2-5/8 3-3/8 3-3/8 3-1/4 3-1/4

1-1/2 1-3/4 2 3-1/2 4 4-1/2 5 5 6 6-1/2

1615 2517 3020 3535 4040 4545 5050 6050 7060 8065

1-5/8 2-1/2 3 3-1/2 4 4-1/2 5 6 7 8

A

Screw Torque (in.-lb.) 175 430 1800 1000 1750 2450 3100 7820 7820 7820

W16 through K50

A

Sprockets

Hub

DYNA-SYNC

TAPER-LOCK Heavy Duty Wing Pulleys

HT Synchrous Belts

SELECTION/DIMENSIONS

K60 through K80

• Flange mount bushing system • Designed to CEMA specifications • Standard crown face or straight face available • Diameters to 60”, face widths exceeding 78” • Available with replaceable WING-LAG • Available from stock

Conveyor Components

QD Heavy Duty Wing Pulleys

QD Hub

A

B

Bushing

Max. Bore

SF E F JS MS NS PS

3/4 7/8 15/16 1-1/16 1-9/16 1-1/4 1

2-1/16 2-3/4 3-3/4 3-3/8 4-13/16 6 6-1/2

SF E F J M N P

2-7/16 3-7/16 3-15/16 4-7/16 5-7/16 6 7

FEATURES/BENEFITS PAGE PT13-2

Screw Torque (in.-lb.) 360 720 900 1620 2700 3600 5400

MODIFICATIONS/ACCESSORIES PAGE PT13-35

A

RELATED PRODUCTS PAGE PT13-40

PT13-23

ENGINEERING/TECHNICAL PAGE PT13-43

Engineering

QD Dimensions


DYNA-SYNC

SELECTION Heavy Duty Wing Pulley Average Weights – HE, TAPER-LOCK and QD Dia. 8 10

HT Synchrous Belts

12

14

16

Sprockets

18

20

Max. Bore 1.63 2.5 1.63 2.5 3 1.63 2.5 3 3.5 1.63 2.5 3 3.5 4 1.63 2.5 3 3.5 4 4.5 2.5 3 3.5 4 45 5 2.5 3 3.5 4 4.5 5

12 33 37 49 52 66 59 62 75 83 81 83 95 102 110 94 96 108 115 122 ... 109 121 128 135 ... ... 125 137 144 151 ... ...

14 38 42 58 59 72 69 70 83 90 94 94 106 112 121 108 108 120 126 135 148 123 135 141 149 162 ... 141 153 159 167 180 ...

16 44 46 66 66 79 78 78 91 98 107 106 117 123 133 123 121 132 138 148 162 138 149 154 164 177 210 158 169 174 184 197 210

18 49 51 74 73 85 88 87 99 106 120 117 128 133 145 137 135 145 150 162 175 152 163 168 179 192 225 174 185 189 200 214 225

Face Width 20 22 55 61 55 60 82 90 80 87 92 98 97 107 95 103 107 115 113 121 133 146 129 140 139 150 144 155 157 169 152 167 148 161 158 171 163 175 175 189 189 203 167 182 177 192 182 196 194 209 208 224 240 256 191 208 201 217 205 221 217 235 231 249 240 256

24 66 64 99 94 105 117 112 123 126 159 152 161 165 181 182 174 184 187 202 217 197 206 210 225 239 271 225 234 237 252 266 271

26 72 68 107 101 112 126 120 131 136 172 164 173 176 193 197 188 197 199 216 231 212 221 224 240 255 286 242 250 253 269 284 286

30 83 77 123 115 125 146 137 147 151 198 187 195 197 216 212 215 222 224 243 259 243 250 252 271 286 317 276 284 285 304 320 317

32 88 82 132 122 131 156 146 155 159 211 199 206 208 228 243 228 235 237 257 273 258 265 266 286 302 333 294 301 302 322 337 333

Conveyor Components

• Crown face pulleys will be provided unless straight face is specified • DODGE Heavy Duty wing Pulleys are designed to meet CEMA wing Pulley Specification 501.1–1988. They are not to be used with steel cable or other high modulus belting. They should not be used at belt speeds greater than 450 FPM.

Engineering FEATURES/BENEFITS PAGE PT13-2

SELECTION/DIMENSIONS PAGE PT13-10

MODIFICATIONS/ACCESSORIES PAGE PT13-35

PT13-24

RELATED PRODUCTS PAGE PT13-40


38 105 95 157 143 151 185 171 179 182 251 234 240 240 264 288 269 275 274 298 315 304 309 309 333 350 379 346 351 351 375 391 379

40 110 126 165 177 178 195 206 208 239 264 246 252 251 276 304 282 288 287 312 329 319 324 323 348 365 395 363 368 367 392 409 395

44 121 139 181 194 194 214 227 227 260 291 270 274 272 300 319 310 314 312 340 358 350 354 351 379 397 426 398 402 400 428 445 426

46 127 145 190 202 202 224 237 236 271 304 282 285 283 312 350 323 327 324 353 372 365 369 366 395 413 441 416 419 416 445 463 441

54 149 169 223 237 234 263 277 274 b14 357 329 331 326 360 403 378 379 374 409 428 426 428 423 457 476 504 486 487 482 516 535 504

57 157 178 235 250 245 278 292 288 330 377 347 348 342 378 426 398 399 393 429 449 450 450 444 481 500 527 512 513 507 543 562 527

60 166 188 248 263 257 292 308 302 346 396 364 365 358 396 451 418 419 412 450 470 473 473 466 504 524 550 538 538 531 569 589 615

63 174 197 260 276 269 307 323 316 362 416 382 382 374 414 473 439 438 431 471 492 496 495 487 527 548 574 565 564 556 596 616 642

66 182 206 272 289 281 322 338 330 378 436 400 399 390 432 496 459 458 449 491 513 519 517 509 551 572 597 591 589 581 622 644 669

DYNA-SYNC

Face Width 51 141 160 210 224 222 248 262 260 298 337 311 314 310 342 365 357 360 355 388 407 403 406 401 434 453 480 459 462 457 489 508 480

Engineering

Conveyor Components

36 99 91 148 136 145 175 163 171 174 238 223 229 229 252 258 255 262 262 285 301 288 294 294 317 334 364 328 334 334 357 373 364

HT Synchrous Belts

Heavy Duty Wing Pulley Average Weights – HE, TAPER-LOCK and QD

Sprockets

SELECTION

FEATURES/BENEFITS PAGES PT13-2

SELECTION/DIMENSIONS PAGE PT13-10

MODIFICATIONS/ACCESSORIES PAGE PT13-35

PT13-25

RELATED PRODUCTS PAGE PT13-40


DYNA-SYNC

SELECTION Heavy Duty Wing Pulley Average Weights – HE, TAPER-LOCK and QD Dia.

24

HT Synchrous Belts

30

36 Sprockets

Max. Bore 2.5 3 3.5 4 4.5 5 6 2.5 3 3.5 4 4.5 5 6 7 8 3 3.5 4 4.5 5 6 7 8

12 175 186 192 198 ... ... ... 281 291 295 298 ... ... ... ... 452 453 453 ... ... ... ... ...

14 198 208 213 220 232 ... ... 318 326 329 333 343 ... ... ... ... 510 509 509 517 ... ... ... ...

16 220 230 234 242 254 285 ... 354 362 363 368 378 406 ... ... 568 566 566 547 596 ... ... ...

18 243 253 256 265 277 307 375 391 398 398 404 414 441 503 559 ... 627 623 623 630 651 705 754 ...

Face Width 20 22 267 290 275 298 278 300 288 311 300 324 330 353 397 419 429 466 434 471 434 469 440 476 450 486 476 511 537 571 592 625 630 663 686 745 680 738 680 738 686 744 706 762 758 812 805 856 830 881

24 314 321 322 334 347 376 442 504 508 505 513 523 548 605 658 697 804 795 796 801 817 866 908 932

26 337 344 345 358 371 399 464 542 545 541 549 559 582 640 691 731 864 854 854 859 874 920 959 983

30 385 391 390 405 419 446 510 618 619 614 623 633 654 709 758 800 984 970 971 975 987 1028 1064 1086

32 409 414 412 429 443 470 533 656 657 650 660 670 691 744 792 834 1044 1029 1029 1033 1044 1083 1117 1138

• Crown face pulleys will be provided unless straight face is specified • DODGE Heavy Duty wing Pulleys are designed to meet CEMA wing Pulley Specification 501.1–1988. They are not to be used with steel cable or other high modulus belting. They should not be used at belt speeds greater than 450 FPM.

Conveyor Components Engineering FEATURES/BENEFITS PAGE PT13-2

SELECTION/DIMENSIONS PAGE PT13-10

MODIFICATIONS/ACCESSORIES PAGE PT13-35

PT13-26

RELATED PRODUCTS PAGE PT13-40


38 482 485 481 501 515 541 602 772 770 760 773 782 800 850 895 939 1225 1206 1207 1209 1215 1249 1276 1296

40 506 508 504 525 539 564 625 811 808 797 810 820 837 886 929 974 1286 1265 1266 1268 1273 1304 1329 1349

44 555 556 550 573 588 612 671 889 884 871 886 895 911 957 998 1044 1408 1384 1385 1386 1388 1415 1436 1454

46 579 579 573 597 612 636 694 928 922 908 923 933 948 993 1032 1079 1469 1443 1445 1446 1446 1471 1490 1508

54 676 674 665 694 710 731 787 1084 1074 1056 1075 1084 1095 1136 1170 1220 1713 1682 1684 1683 1677 1694 1705 1720

57 713 710 700 730 746 767 821 1142 1132 1112 1132 1141 1151 1190 1222 1272 1805 1772 1774 1772 1764 1778 1786 1800

60 750 746 734 766 783 803 856 1201 1189 1168 1189 1198 1207 1243 1274 1325 1897 1861 1864 1862 1852 1862 1867 1880

63 787 782 769 803 819 839 891 1260 1247 1224 1246 1255 1262 1297 1326 1378 1989 1951 1954 1951 1939 1946 1948 1961

66 823 818 804 839 856 875 926 1319 1304 1280 1303 1312 1318 1351 1378 1431 2082 2041 2044 2041 2026 2031 2029 2041

DYNA-SYNC

Face Width 51 640 639 630 657 673 695 752 1025 1017 1001 1018 1028 1040 1082 1119 1167 1621 1592 1594 1594 1590 1610 1624 1640

Engineering

Conveyor Components

36 457 461 458 477 491 517 579 733 732 723 735 745 764 815 860 904 1165 1147 1147 1150 1158 1193 1223 1243

HT Synchrous Belts

Heavy Duty Wing Pulley Average Weights – HE, TAPER-LOCK and QD

Sprockets

SELECTION

FEATURES/BENEFITS PAGES PT13-2

SELECTION/DIMENSIONS PAGE PT13-10

MODIFICATIONS/ACCESSORIES PAGE PT13-35

PT13-27

RELATED PRODUCTS PAGE PT13-40


DYNA-SYNC

SELECTION Mine Duty Extra Drum & Wing Pulleys • Greater capacity than standard mine duty pulleys • Rigid duty construction • Hub is integral to the end disc eliminating stresses at the hub weld • Standard crown face or straight face available

HT Synchrous Belts

• HE compression hubs • Diameters to 60”, face widths exceeding 78” Mine Duty Extra Drum Pulley

• Balanced design: all components have matched safety factors • Available in spiral drum and wing pulley construction

Sprockets

Mine Duty Extra Wing Pulley

Mine Duty Extra Drum Pulley

Mine Duty Pulley Types Conveyor Components Engineering

Mine Duty Extra (Integral Hub Design)

FEATURES/BENEFITS PAGE PT1 -2

Standard Mine Duty (Welded Design)

O IFICATIONS/ACCESSORIES PAGE PT1 -

RELATE PRO UCTS PAGE PT1 -40

PT13-28

ENGINEERING/TECHNICAL PAGE PT1 -4


Spiral Wing Pulleys • Self cleaning, maximizes belt life

DYNA-SYNC

SELECTION

HT Synchrous Belts

• Diameters to 60”, face widths exceeding 78”

Mine Duty Spiral Wing Pulley

Shafting

• Shafting up to 30” diameter, 22’ in length • Precision machined, custom designed • C1045 turned and polished through 5-15/16 • 4140 and stainless steel available upon request • Available from stock for stock CEMA drum and wing pulleys • Integrate shafting with other DODGE components

Sprockets

• C1045 hot rolled 6” and above

Engineering

Conveyor Components

• Shafting available for non conveyor component applications

FEATURES/BENEFITS PAGE PT1 -2

O IFICATIONS/ACCESSORIES PAGE PT1 -

RELATE PRO UCTS PAGE PT1 -40

PT13-29

ENGINEERING/TECHNICAL PAGE PT1 -4


DYNA-SYNC

SELECTION Engineered Class Pulleys • Maximum strength and reliability • Two year warranty • Serialized nameplate • Custom designed for specific applications • Bore range exceeding 23”

HT Synchrous Belts

• Integral hub design utilizing one of the styles shown below.

Sprockets Conveyor Components Welded Design

Integral Hub Design

T-Section Design

Engineering FEATURES/BENEFITS PAGE PT1 -2

O IFICATIONS/ACCESSORIES PAGE PT1 -

RELATE PRO UCTS PAGE PT1 -40

PT13-30

ENGINEERING/TECHNICAL PAGE PT1 -4


Super Pulleys • Proven leader in design and manufacturing

DYNA-SYNC

SELECTION

• 400+ successful super pulley installations • Dedicated manufacturing facility with complete in-house capabilities • 60-step quality control process including complete weld inspection and test • Finite element design HT Synchrous Belts

• Complete material certification • Certified welding

Engineering

Conveyor Components

Sprockets

• Technologically advanced lagging material

FEATURES/BENEFITS PAGE PT1 -2

O IFICATIONS/ACCESSORIES PAGE PT1 -

RELATE PRO UCTS PAGE PT1 -40

PT13-31

ENGINEERING/TECHNICAL PAGE PT1 -4


DYNA-SYNC

SELECTION Dead Shaft Pulleys • Compact design, used where space is critical • Shaft diameters exceeding 7-1/2” • Bearings are integral to the end disc allowing for shaft misalignment

HT Synchrous Belts

Elevator Pulleys Sprockets

• Heavy, all steel construction • Economical alternative in narrow belt applications • Standard crown face or available straight face • HE compression hubs • Diameters to 30”, face widths to 16”

Conveyor Components Engineering FEATURES/BENEFITS PAGE PT1 -2

O IFICATIONS/ACCESSORIES PAGE PT1 -

RELATE PRO UCTS PAGE PT1 -40

PT13-32

ENGINEERING/TECHNICAL PAGE PT1 -4


DYNA-SYNC

SELECTION/DIMENSIONS Steel Split Pulleys • Applied in narrow belt applications • Die formed, riveted construction • Provides the best possible weight to strength ratio • Interchangeable bushings for bores from 3/4” to 3-1/2”

Bore Size

P/N

3/4 1 1-3/16

051009 051020 051016

3/4 1 1-3/16 1-1/4 1-7/16 1-1/2 1-11/16

051029 051033 051036 051037 051040 051048 051044

3/4 1 1-3/16 1-1/4 1-7/16 1-1/2 1-15/16 2-3/16

051059 051063 051066 051067 051070 051071 051078 051082

L BUSHING Bushing Shaft Keyway Keyway 3/16 x 3/32 3/16 x 3/32 1/4 x 1/8 1/4 x 1/8 * * N BUSHING 3/16 x 3/32 3/16 x 3/32 1/4 x 1/8 1/4 x 1/8 1/4 x 1/8 1/4 x 1/8 1/4 x 1/8 1/4 x 1/8 3/8 x 1/8 3/8 x 1/16 3/8 x 1/16 3/8 x 1/8 * * SF BUSHING 3/16 x 3/32 3/16 x 3/32 1/4 x 1/8 1/4 x 1/8 1/4 x 1/8 1/4 x 1/8 1/4 x 1/8 1/4 x 1/8 3/8 x 1/8 3/8 x 1/16 3/8 x 1/8 3/8 x 1/16 1/2 x 1/8 1/2 x 1/8 * *

Key Required 3/16 x 3/16 1/4 x 1/4 * 3/16 x 3/16 1/4 x 1/4 1/4 x 1/4 1/4 x 1/4 3/8 x 5/8 3/8 x 5/16 * 3/16 x 3/16 1/4 x 1/4 1/4 x 1/4 1/4 x 1/4 3/8 x 5/16 3/8 x 5/16 1/2 x 3/8 *

Bore Size

P/N

1-3/16 1-1/4 1-7/16 1-1/2 1-11/16 1-15/16 2 2-3/16 2-7/16 2-15/16 3-7/16

051211 051212 051215 051216 051219 051223 051224 051227 051231 051250 051247

G BUSHING Bushing Shaft Keyway Keyway 1/4 x 1/8 1/4 x 1/8 1/4 x 1/8 1/4 x 1/8 3/8 x 1/8 3/8 x 3/16 3/8 x 1/8 3/8 x 3/16 3/8 x 1/8 3/8 x 3/16 1/2 x 1/8 1/2 x 1/4 1/2 x 1/8 1/2 x 1/4 1/2 x 1/8 1/2 x 1/4 5/8 x 3/16 5/8 x 5/16 3/4 x 3/16 3/4 x 3/8 * *

Key Required 1/4 x 1/4 1/4 x 1/8 3/8 x 5/16 3/8 x 5/16 3/8 x 5/16 1/2 x 1/8 1/2 x 1/8 1/2 x 1/8 5/8 x 1/2 3/4 x 9/16 *

* Keyways are not available in these sizes.

Sprockets

• Pulleys can be lagged with any standard lagging

Conveyor Components

• Max speed = 2500 ft/min

HT Synchrous Belts

• Available from stock

Engineering

Max bore does not use a bushing. Bushing can not be re-bored.

FEATURES/BENEFITS PAGE PT13-2

MODIFICATIONS/ACCESSORIES PAGE PT13-36

RELATED PRODUCTS PAGE PT13-41

PT13-33

ENGINEERING/TECHNICAL PAGE PT13-44


DYNA-SYNC

SELECTION/DIMENSIONS Steel Split Pulleys Face Width *

HT Synchrous Belts Sprockets Conveyor Components

Overall Bushing Face Overall Bushing Face Overall Bushing Part Wt. Max. Part Wt. Max. Hub Symbol Width Hub Symbol Width Hub Symbol No. Δ Bore No. Δ Bore ◊ Length * ◊ Length * ◊ Length 3” Diameter 12” Diameter 8” Diameter 3 203005 1.3 1-7/16 3 L 3 200050 13 3-1/2 3-5/8 G 4 203006 1.4 1-7/16 3 L 2 200017 5.6 2-7/16 2-3/8 SF 4 200051 14 3-1/2 3-5/8 G 5 203007 1.6 1-7/16 3 L 3 200018 7.7 3-1/2 3-5/8 G 5 200052 15 3-1/2 3-5/8 G 3 L 4 200019 8.5 3-1/2 3-5/8 G 6 200053 17 3-1/2 3-5/8 G 6 203008 1.7 1-7/16 4” Diameter 5 200020 9.3 3-1/2 3-5/8 G 8 200054 26 3-1/2 7-1/2 2-G 3 203015 1.7 1-15/16 3 N 6 200021 9.9 3-1/2 3-5/8 G 10 200055 29 3-1/2 9-1/2 2-G 4 203016 2.4 1-15/16 3 N 8 200022 16 3-1/2 7-1/21 2-G 12 200056 31 3-1/2 11-1/2 2-G 5 203017 3.2 1-15/16 3 N 10 200023 17 3-1/2 9-1/2 2-G 14” Diameter 6 203018 5.6 1-15/16 3 N 12 200024 19 3-1/2 11-1/2 2-G 3 200070 14 3-1/2 3-5/8 G 5” Diameter 4 200071 16 3-1/2 3-5/8 G 9” Diameter 3 203025 2.8 1-15/16 N 5 200072 18 3-1/2 3-5/8 G G 6 200073 19 3-1/2 3-5/8 G 4 203026 3.0 1-15/16 3 N 3 200026 8.9 3-1/2 3-5/8 5 203027 3.5 1-15/16 3 N 4 200027 9.5 3-1/2 3-5/8 G 7 200074 30 3-1/2 7-1/2 2-G 6 203028 6.3 1-15/16 3 N 5 200028 11 3-1/2 3-5/8 G 10 200075 32 3-1/2 9-1/2 2-G 6” Diameter 6 200029 12 3-1/2 3-5/8 G 12 200076 36 3-1/2 11-1/2 2-G 2 200001 4.3 2-7/16 2-3/8 SF 8 200030 18 3-1/2 7-1/2 2-G 16” Diameter 3 200002 4.5 2-7/16 2-3/8 SF 10 200031 20 3-1/2 9-1/2 2-G 3 200088 17 3-1/2 3-5/8 G 4 200003 5.3 2-7/16 2-3/8 SF 12 200032 22 3-1/2 11-1/2 2-G 4 200089 18 3-1/2 3-5/8 G 5 200004 6.0 2-7/16 2-3/8 SF 5 200090 19 3-1/2 3-5/8 G 10” Diameter G 6 200005 6.8 2-7/16 2-3/8 SF 6 200091 21 3-1/2 3-5/8 8 200006 10 2-7/16 6-3/4 2-SF 3 200034 9.7 3-1/2 3-5/8 G 8 200092 34 3-1/2 7-1/2 2-G 10 200007 12 2-7/16 8-3/4 2-SF 4 200035 9.5 3-1/2 3-5/8 G 10 200093 37 3-1/2 9-1/2 2-G G 12 200094 40 3-1/2 11-1/2 2-G 12 200008 14 2-7/16 10-3/4 2-SF 5 200036 11 3-1/2 3-5/8 7” Diameter 6 200037 12 3-1/2 3-5/8 G 18” Diameter 3 200010 5.1 2-7/16 2-3/8 SF 8 200038 18 3-1/2 7-1/2 2-G 3 200106 18 3-1/2 3-5/8 G 4 200011 6.0 2-7/16 2-3/8 SF 10 200039 20 3-1/2 9-1/2 2-G 4 200107 20 3-1/2 3-5/8 G 5 200012 7.0 2-7/16 2-3/8 SF 12 200040 22 3-1/2 11-1/2 2-G 5 200108 22 3-1/2 3-5/8 G G 6 200013 7.9 2-7/16 2-3/8 SF 6 200109 26 3-1/2 3-5/8 11” Diameter 8 200014 11 2-7/16 6-3/4 2-SF 20” Diameter 10 200015 13 2-7/16 8-3/4 2-SF 3 200042 11 3-1/2 3-5/8 G 3 200124 20 3-1/2 3-5/8 G 12 200016 15 2-7/16 10-3/4 2-SF 4 200043 9.5 3-1/2 3-5/8 G 4 200125 22 3-1/2 3-5/8 G 6 200045 12 3-1/2 3-5/8 G 5 200126 24 3-1/2 3-5/8 G 6 200127 25 3-1/2 3-5/8 G * Crown face will be furnished unless straight face is specifically Keyways – Pulleys are designed to transmit power by gripping the ordered. shaft, and the keyways are not ordinarily required. Bushings will not Δ Weight does not include weight of bushing. have a keyway unless requested. ◊ One bushing required per pulley except two required where figure 2 precedes bushing symbol. Part No.

Wt. Δ

Max. Bore

Bushings

Overall Pulley Face Widths

Overall Face Width for Various Nominal Face Widths Pulley Pulley Diam. 2 3 4 5 6 8 10 12 3 .... 3-11/16 4-11/16 5-11/16 6-11/16 .... .... .... 4 .... 3-9/16 4-7/16 5-7/16 6-5/16 .... .... .... L .4 5 .... 3-9/16 4-5/16 5-5/16 6-5/16 .... .... .... N 1.0 6-7 2-3/16 3-5/8 4-11/16 5-11/16 6-11/16 8-11/16 10-11/16 12-11/16 SF 1.3 8-11 2-3/16 4 4-11/16 5-11/16 6-11/16 8-11/16 10-11/16 12-11/16 G 2.7 12-11 .... 4 4-11/16 5-11/16 6-11/16 8-11/16 10-11/16 12-11/16 18-20 .... 4 4-11/16 5-11/16 6-11/16 .... .... .... Δ Bushing will not have a keyway unless requested. Keys are not included in price. For quantity of bushings required per pulley and symbol of bushing see table above. s in S o

Engineering

Max. Bore OutNo With Min. side Lgth. e a Key- Bore Diam. Δ way 1-3/16 1 3/4 1-7/16 3 1-11/16 1-1/2 3/4 1-15/16 3 2-3/16 1-15/16 3/4 2-7/16 2-3/8 3-7/16 2-15/16 1-3/16 3-1/2 3/5/8

Avg . Wt.

FEATURES/BENEFITS PAGE PT13-2

MODIFICATIONS/ACCESSORIES PAGE PT13-36

RELATED PRODUCTS PAGE PT13-41

PT13-34

ENGINEERING/TECHNICAL PAGE PT13-44

14 .... .... .... .... .... .... ....


Conveyor Pulley Lagging

DYNA-SYNC

MODIFICATIONS/ ACCESSORIES

• Increases belt tractions • Eliminates rim wear due to abrasive conditions • Promotes cleaning action

HT Synchrous Belts

• 60 durometer hardness standard, 70 and 45 available on request

Diamond Grooved

Lagging Styles • Vulcanized: plain or grooved • D-LAG: DODGE exclusive premium rubber polymer designed to maximize abrasion resistance • Neoprene: flame retardant and oil resistant Sprockets

• Tuff-Top: vulcanized with a rough top finish • Holz: replaceable slide on lagging can be installed or replaced with pulley installed • WING-LAG: replaceable high abrasion slide on wing pulley lagging • Wing Pulleys can have vulcanized lagging

D-LAG

Contact Bar Holz Slotted WING-LAG slides over contact bars FEATURES/BENEFITS PAGE PT1 -2

SELECTION/ I ENSIONS PAGE PT1 -10

RELATE PRO UCTS PAGE PT1 -40

PT13-35

ENGINEERING/TECHNICAL PAGE PT1 -4

Engineering

Plain

Conveyor Components

• Ceramic Lagging: For pulleys with slippage and high wear characteristics


DYNA-SYNC

MODIFICATIONS/ ACCESSORIES Lagging Weights 1/4” PLAIN VULCANIZED RUBBER LAGGING WEIGHTS Pulley Dia.

HT Synchrous Belts

6 8 10 12 14 16 18 20 24 30 36 42 48 54 60

12 3 4 6 6 7 8 9 10 12 16 18 ... ... ... ...

14 4 5 6 7 8 9 10 12 14 17 20 ... ... ... ...

16 4 6 6 8 9 11 12 14 16 20 24 29 32 36 40

18 5 6 7 9 11 12 14 16 18 23 27 32 36 40 46

20 5 6 8 10 12 14 15 17 20 26 30 36 40 45 51

22 6 7 9 11 13 15 16 18 22 28 33 40 44 50 56

24 6 8 10 12 15 17 18 20 24 30 36 43 48 64 61

Weights for Various Face Widths 26 30 32 36 38 44 6 7 8 9 10 11 9 10 11 12 13 15 11 13 14 16 17 18 13 15 16 18 19 22 16 17 19 21 23 26 17 20 22 25 26 30 19 22 25 28 29 34 22 26 28 30 32 41 26 30 32 36 38 44 33 39 40 45 49 56 39 45 49 55 58 67 46 53 57 64 68 78 52 60 63 72 75 87 60 64 74 82 87 101 66 76 82 92 97 102

46 12 16 19 23 28 31 35 40 46 59 71 82 92 106 118

51 13 17 22 26 30 35 39 43 51 65 78 92 104 117 130

54 14 18 23 27 32 37 41 46 54 69 83 97 111 124 138

57 15 19 24 29 34 39 43 49 57 73 87 102 116 131 145

60 16 20 26 30 36 41 45 51 60 76 92 107 122 137 153

63 17 21 27 32 38 43 48 53 64 80 97 112 129 144 161

66 17 23 28 33 40 45 51 56 66 84 101 118 135 152 168

NOTE: For weights of other lagging, multiply weight given above by factors listed below. Sprockets

3/8”, 1/2” VULCANIZED RUBBER LAGGING WEIGHT FACTORS Type 3/8” Plain 1/2” Plain

Weight Factor 1.49 1.99

Type 3/8” Grooved 1/2” Grooved

Weight Factor 1.40 1.89

See instructions in footnote above. Conveyor Components

Lagging Comparison Description DODGE D-LAG DODGE STD60 DOSGE STD 70 DODGE STD 45 DODGE NEO60 (MSHA) DODGE NEO 70

Compound

DURO

Abrasion Ranking

PROPRIETARY SBR SBR SBR NEOPRENE NEOPRENE

65 60 70 45 60 70

173 100 146 51 125 166

DIN Abrasion (mm^3) 117 202 138 393 162 122

Tensile (psi)

Elongation ( %)

2895 1660 2075 1753 1425 1528

600 380 400 650 350 275

Engineering FEATURES/BENEFITS PAGE PT1 -2

SELECTION/ I ENSIONS PAGE PT1 -10

RELATE PRO UCTS PAGE PT1 -40

PT13-36

ENGINEERING/TECHNICAL PAGE PT1 -4


SLIDE LAG速 Replaceable pads are designed to fit under the lips of the retainers, allowing the pads to slide in and out during installation. Slide Lag can be installed on conveyor systems without removing the pulleys from their operating positions.

DYNA-SYNC

MODIFICATIONS/ ACCESSORIES

Part Number

Description

207349

6" Diameter Style 5

207325

8" Diameter Style 5

207326

10" Diameter Style 5

207327

12" Diameter Style 5

207328

14" Diameter Style 5

Factory hot-vulcanization under pressure assures the best possible bond of rubber to backing plate. No lagging failures from loss of adhesion and separation-the most common problems associated with conventional lagging.

207329

16" Diameter Style 5

207330

18" Diameter Style 5

207331

20" Diameter Style 5

207332

24" Diameter Style 5

Steel backing plates are precision formed at the factory to fit the curved surface provided by each individual pulley diameter. Insures proper pad stability and long life.

207333

30" Diameter Style 5

207334

36" Diameter Style 5

Exclusive elastomer compounding provides a lagging pad with exceptional drive-pulley traction, abrasion resistance and extra long service life. The elastomer retains its integrity under the most severe operating conditions.

Other styles of Slide Lag are available upon request. DODGE conveyor pulleys can be readily obtained with Slide Lag pre-installed from the factory.

Sprockets

Rust resistant metal retainers are permanently welded or bolted to the pulley face to securely hold the lagging pads in place. When properly installed, lagging cannot shift or pull free from the effects of impact, trapped material or belt or product movement.

HT Synchrous Belts

Part Numbers for Style #5 Slide Lag

Ordering Slide Lag with Retainers

D I A M E T E R

12" 1 1 1 1 2 2 2 2 2 3 3 4 4 5 5 6

14" 1 1 1 2 2 2 2 2 3 3 4 5 5 6 6 7

FEATURES/BENEFITS PAGE PT1 -2

16" 1 1 2 2 2 2 2 3 3 4 4 5 6 6 7 8

18" 1 1 2 2 2 2 3 3 3 4 5 6 6 7 8 9

20" 1 2 2 2 2 3 3 3 4 5 5 6 7 8 9 10

22" 1 2 2 2 3 3 3 4 4 5 6 7 8 9 10 11

SELECTION/ I ENSIONS PAGE PT1 -10

38" 2 3 3 4 4 5 5 6 7 8 10 12 13 15 16 19

40" 2 3 3 4 4 5 5 6 7 9 10 12 14 15 17 20

RELATE PRO UCTS PAGE PT1 -40

PT13-37

44" 2 3 4 4 5 5 6 7 8 10 11 13 15 17 19 22

46" 2 3 4 4 5 6 6 7 8 10 12 14 16 18 20 23

51" 3 3 4 5 5 6 7 8 9 11 13 15 17 20 22 26

54" 3 3 4 5 6 6 7 8 9 12 14 16 18 21 23 27

60" 3 4 5 5 6 7 8 9 10 13 15 18 20 23 25 30

66" 3 4 5 6 7 8 9 10 11 14 17 20 22 25 28 33

ENGINEERING/TECHNICAL PAGE PT1 -4

72" 3 4 5 6 7 8 9 10 12 15 18 21 24 27 30 36

Engineering

P U L L E Y

6" 8" 10" 12" 14" 16" 18" 20" 24" 30" 36" 42" 48" 54" 60" 72"

PULLEY FACE WIDTH 24" 26" 30" 32" 36" 1 2 2 2 2 2 2 2 2 2 2 2 3 3 3 2 3 3 3 3 3 3 3 4 4 3 3 4 4 4 3 4 4 4 5 4 4 5 5 5 4 5 5 6 6 5 6 7 7 8 6 7 8 8 9 7 8 9 10 11 8 9 10 11 12 9 10 12 12 14 10 11 13 14 15 12 13 15 16 18

Conveyor Components

For the most common pulley sizes, select the number of 72" pads needed from the Table below.


DYNA-SYNC

MODIFICATIONS/ ACCESSORIES WING-LAG™ A space age poly-elastomer that improves the performance of conventional wing pulleys. Designed to beat the heat or cold...oil, chemicals or abrasivies...for any tough conveyor operation where the job calls for lagged wing pulleys...WING-LAG will do the job better and last longer. Tougher than rubber. WING-LAG will outlast rubber lagging 2-5 times.

HT Synchrous Belts

Resists chemicals and abrasives. WING-LAG is not affected by most oils, hydraulic fluids, fuels, chemicals and abrasives. Excellent temperature range. WING-LAG has an effective operating temperature range of -60 degrees F to +212 degrees F. WING-LAG grips the wing pulley and stays in place as if it were glued. However, it requires no special metal channeling, retaining grooves or other designed-in retaining feature, therefore it goes on easily and removes easily.

Contact Bar

Greater protection from foreign objects. Because of its tough composition, rocks, coal chunks and other debris trapped between the conveyor belt and the wing will simply be thrown out when the pulley has completed its turn.

Ordering WING-LAG Sprockets

For the most common pulley sizes, select the number of the wings from the Table below. To calculate the number of 72" pieces needed, multiple the number of wings by the face width and divide by 72. Round the number of pieces up to the next largest number.

10 12

Heavy Duty No. of Wings 7 8 8

14 16 18 20 24 30 36 42 48

Diameter 8

Conveyor Components

54 60

207300 207300 207300

Mine Duty No. of Wings 7 8 10

10 10 10 10

207300 207300 207300 207301

10 10 12 12

207301 207301 207301 207301

12 16 18 22 24 28

207301 207301 207301 207301 207301 207301

14 16 18 22 24 28

207301 207301 207301 207301 207301 207301

30

207301

30

207301

Part Number

Part Number 207301 207301 207301

Engineering

WING-LAG is available on standard or custom wing pulleys pre-installed at the factory or it can be retro-fit in the field. Either way a WING-LAG wing pulley will extend the life of conveyor belts and conventional wing pulleys under the most severe operating conditions.

FEATURES/BENEFITS PAGE PT1 -2

SELECTION/ I ENSIONS PAGE PT1 -10

RELATE PRO UCTS PAGE PT1 -40

PT13-38

ENGINEERING/TECHNICAL PAGE PT1 -4


Conveyor Pulley Assemblies

DYNA-SYNC

MODIFICATIONS/ ACCESSORIES

• Maximize return on investment • Single source supplier, single source warranty • Computer aided product selection • Complete package of bearing and power transmission components

Sprockets

Drum Pulley Assembly

HT Synchrous Belts

• No on-site component assembly

Engineered Class Pulley Assembly

Conveyor Components

Drum Pulley Assembly

Wing Pulley Assembly

Engineering

Spiral Wing Pulley Assembly

FEATURES/BENEFITS PAGE PT1 -2

SELECTION/ I ENSIONS PAGE PT1 -10

RELATE PRO UCTS PAGE PT1 -40

PT13-39

ENGINEERING/TECHNICAL PAGE PT1 -4


DYNA-SYNC

RELATED PRODUCTS HE Bushings HE BUSHING DIMENSIONS L (in.)

B.C. (in.)

F (in.)

H (in.)

Number of Bolts

HE-25 HE-30

Maximum Bore (in.) 2-1/2 3

2-1/4 2-3/4

3-15/16 4-11/16

3/4 7/8

4-5/8 5-5/8

4 4

Size of Bolts (in.) 3/8-16 x 1-3/4 1/2-13 x 2-1/4

HE-35 HE-40 HE-45 HE-50

3-1/2 4 4-1/2 5

3 3-1/2 4 4-1/2

5-9/16 6-5/16 7-5/16 8

7/8 1 1-1/4 1-1/2

6-5/8 7-1/2 8-3/4 9-5/8

4 4 6 6

9/16-12 x 2-1/4 5/8-11 x 2-1/2 5/8-11 x 2-1/2 3/4-10 x 3

HE-60 HE-70 HE-80

6 7 8

5-1/4 6-1/4 7

9-1/4 10-9/16 12-1/8

1-3/4 2 2-1/4

11-1/8 12-3/4 14-1/2

6 6 6

7/8-9 x 3-1/2 1-8 x 4 1-1/8-7 x 4-1/2

HE-100 HE-120

10 12

9 10

14-1/2 17-1/2

3 3

17 20

6 8

1-1/4-7 x 5-1/2 1-1/4-7 x 5-1/2

Bushing

HT Synchrous Belts Sprockets

Wrench Torque

HE-25

Wrench Torque (ft.-lbs.) 30

HE-30 HE-35 HE-40 HE-45

60 90 140 140

HE-50 HE-60

200 350

HE-70 HE-80

500 500

HE-100 HE-120

600 600

Bushing

Conveyor Components

HE-25 to HE120 Engineering

Details for TAPER-LOCK Bushings - See page PT6-2 Details for QD Bushings - See page PT6-15

FEATURES/BENEFITS PAGES PT13-2 - PT13-3

SELECTION/DIMENSIONS PAGE PT13-10

MODIFICATIONS/ACCESSORIES PAGE PT13-35

PT13-40

ENGINEERING/TECHNICAL PAGE PT13-43


HE-30

HE-35

HE-40

1 1-1/8 1-3/16 1-1/4 1-5/16 1-3/8 1-7/16 1-1/2 1-11/16 1-3/4 1-13/16 1-7/8 1-15/16 2 2-1/8 2-3/16 2-1/4 2-5/16 2-3/8 2-7/16 2-1/2 1-3/8 1-7/16 1-1/2 1-11/16 1-3/4 1-15/16 2 2-3/16 2-7/16 2-1/2 2-9/16 2-11/16 2-3/4 2-13/16 2-7/8 2-15/16 3 1-3/16 1-7/16 1-1/2 1-11/16 1-3/4 1-15/16 2 2-3/16 2-1/4 2-3/8 2-7/16 2-1/2 2-11/16 2-3/4 2-7/8 2-15/16 3 3-3/16 3-3/8 3-7/16 3-1/2 1-15/16 2-3/16 2-7/16 2-1/2 2-11/16 2-15/16 3-3/16 3-11/16 3-7/16 3-7/8 3-15/16 4

FEATURES/BENEFITS PAGES PT13-2 - PT13-3

Wt. 4 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 6 6 6 6 6 6 6 6 6 6 6 6 5 5 5 6 5 8 8 8 8 9 9 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 13 13 13 13 13 13 13 13 13 21 13 12

Bush. No.

Bushing Keyway

Shaft Keyway

1/4 x 1/8

1/4 x 1/8

5/16 x 5/32

5/16 x 5/32

3/8 x 3/16

3/8 x 3/16

HE-45

HE-50 1/2 x 1/4

1/2 x 1/4

5/8 x 3/16▲

5/8 x 5/16

5/16 x 5/32

5/16 x 5/32

3/8 x 3/16

3/8 x 3/16

HE-60

HE-70 1/2 x 1/4

5/8 x 5/16

1/2 x 1/4

5/8 x 5/16

HE-80 3/4 x 1/8▲

3/4 x 3/8

1/4 x 1/8

1/4 x 1/8

HE-100 3/8 x 3/16

3/8 x 3/16

1/2 x 1/4

1/2 x 1/4

5/8 x 5/16

5/8 x 5/16

HE-120

3/4 x 3/8

3/4 x 3/8

Bore 1-15/16 2-7/16 2-15/16 3-7/16 3-1/2 3-15/16 4-3/16 4-7/16 4-1/2 2-15/16 3-7/16 3-15/16 4-7/16 4-15/16 5 3-15/16 4-1/4 4-7/16 4-15/16 5-7/16 5-1/2 5-15/16 6 5-15/16 6 6-7/16 6-1/2 6-15/16 7 6-7/16 7-1/2 6-15/16 7-7/16 7-15/16 8 7-1/2 7-15/16 8 8-1/2 8-15/16 9 9-1/2 10 8-1/2 9 9-1/2 10 10-1/2 11 11-1/2 12

Part No. 206670 206660 206662 206664 206671 206666 206672 206668 206673 207998 206817 206818 206675 206677 206821 206686 206687 206688 206680 206682 206823 206684 206825 206690 207396 206692 206845 206694 206847 206700 206849 206702 206704 206706 206708 206710 206712 206718 206720 206714 206722 206724 206716 207380 207382 207384 207386 207388 207390 207392 207394

Wt. 22 22 22 22 22 21 21 21 21 30 40 35 29 23 50 47 65 50 49 40 49 38 72 71 71 71 69 69 111 105 108 105 102 100 200 198 195 193 196 191 189 190 415 395 375 353 330 308 285 261

Bushing Keyway 1/2 x 1/4 5/8 x 5/16 3/4 x 3/8

Shaft Keyway 1/2 x 1/4 5/8 x 5/16 3/4 x 3/8

7/8 x 7/16

7/8 x 7/16

1 x 1/2

1 x 1/2

1 x 1/4▲

1 x 1/2

7/8 x 7/16

7/8 x 7/16

1 x 1/2

1 x 1/2

1-1/4 x 1/4▲

1-1/4 x 5/8

1 x 1/2

1 x 1/2

1-1/4 x 5/8

1-1/4 x 5/8

1-1/2 x 1/4▲

1-1/2 x 3/4

1-1/2 x 3/4

1-1/2 x 3/4

1-3/4 x 1/4▲

1-3/4 x 3/4

1-1/2 x 3/4

1-1/2 x 3/4

1-3/4 x 3/4

1-3/4 x 3/4

2 x 3/4

2 x 3/4

1-3/4 x 3/4

1-3/4 x 3/4

2 x 3/4

2 x 3/4

2-1/2 x 7/8

2-1/2 x 7/8

2 x 3/4

2 x 3/4

2-1/2 x 7/8

2-1/2 x 7/8

3x1

3x1

▲ Keys Furnished For These Sizes Only

DYNA-SYNC

Part No. 206623 206744 206615 206745 206747 206748 206617 206750 206752 206754 206756 206758 206619 206760 205997 206763 206765 206767 206768 206621 206770 206635 206625 206637 206639 206772 206627 206774 206775 206629 206777 206838 206631 206778 206779 206780 206633 206781 206648 206649 206784 206786 206839 206640 206788 206790 206792 206794 206642 206795 206796 206798 206800 206644 206801 206803 206840 206646 206807 206658 206659 206810 206811 206650 206652 206812 206813 206654 206841 206656 206815

HT Synchrous Belts

HE-25

Bore

Reborable HE Bushings 7/8 x 3/16▲

7/8 x 7/16

1/2 x 1/4

1/2 x 1/4

5/8 x 5/16

5/8 x 5/16

3/4 x 3/8

3/4 x 3/8

7/8 x 7/16

7/8 x 7/16

1 x 1/4▲

1 x 1/2

Bushing

Part Number

Minimum Bore

HE25 HE30 HE35 HE40 HE45 HE50 HE60 HE70 HE80 HE100 HE120

207960 207961 207962 207963 230794 207965 207966 207967 207968 207969 207970

15/16 15/16 1-3/16 1-15/16 1-15/16 2-15/16 3-7/16 4-7/16 5-7/16 6-15/16 7-15/16

SELECTION/DIMENSIONS PAGE PT13-10

Maximum Bore (in.) Sq. Key 2-1/4 2-3/4 3-1/4 3-3/4 3-15/16 4-1/2 5-1/2 6-1/2 8 10 12

MODIFICATIONS/ACCESSORIES PAGE PT13-35

PT13-41

Inch Maximum Bore (in.) Shallow Key 2-1/2 3 3-1/2 4 4-1/2 5 6 7 -

Metric Minimum Maximum Bore Bore (mm) (mm) 24 60 24 75 32 85 50 100 50 110 75 125 90 150 120 170 140 200 180 250 220 300

ENGINEERING/TECHNICAL PAGE PT13-43

Engineering

Bush. No.

Sprockets

HE Bushings

Conveyor Components

RELATED PRODUCTS


DYNA-SYNC

RELATED PRODUCTS Keyless Locking Assemblies The DODGE Pulley Pros have been designing and fabricating special pulleys with Keyless Locking Assemblies for over 30 years. Hubs are computer designed for use with single or dual locking assemblies.

HT Synchrous Belts

Keyless locking assemblies are available in two basic configurations – short series and long series. Long series locking assemblies feature a longer length thru bore with a corresponding increase in contact area between the locking assembly and the shaft and hub. Most conveyor pulley applications require only one short series locking assembly in each pulley hub to transmit the bending and torsional moments. Heavier loaded pulleys require long series or dual short series locking assemblies to transmit increased loads. The DODGE Pulley Pros have the experience and expertise to determine the best keyless locking assembly configuration for any application.

Sprockets

DODGE Keyless Locking Assemblies are self-contained, high torque capacity, shaft-hub locking devices. They provide many features and benefits to conveyor pulley assemblies, including no keyway stress concentration, no axial movement during assembly, high torque capacity, and easy assembly and disassembly. The locking assembly design includes concentric, tapered rings. As the locking screws are torqued, the locking assembly clamps down on the shaft and expands into the hub bore, establishing a tight mechanical shrink fit.

Short Series Locking Assembly

Long Series Locking Assembly

Conveyor Components

Short Series

Duplex Series Locking Assembly

Long Series Locking Assembly

Engineering

Available in Weld On Hub, Integral Hub or T-Section. See Page PT13-30.

FEATURES/BENEFITS PAGES PT13-2 - PT13-3

SELECTION/DIMENSIONS PAGE PT13-10

MODIFICATIONS/ACCESSORIES PAGE PT13-35

PT13-42

ENGINEERING/TECHNICAL PAGE PT13-43


DYNA-SYNC

ENGINEERING/TECHNICAL Horsepower and Belt Tension for Simple Conveyors * Table 1 – HP Required to Operate Loaded Conveyor on the Level 350

400

500

600

700

800

900

1000

3.0 3.6 4.1 4.5 5.0 5.5 6.0 6.4 6.8 7.5 8.4 9.2 10.2 11.1 12.2

3.3 3.9 4.5 4.9 5.4 5.9 6.5 7.0 7.3 8.0 9.0 10.0 11.0 12.0 13.2

3.5 4.2 4.8 5.3 5.8 6.3 7.0 7.5 8.0 8.8 9.8 10.7 11.9 13.0 14.3

4.0 4.8 5.5 6.0 6.6 7.2 8.0 8.6 9.2 10.1 11.2 12.2 13.6 14.9 16.4

4.5 5.4 6.2 6.8 7.4 8.1 9.0 9.7 10.4 11.4 12.6 13.7 15.3 16.8 18.5

5.0 6.0 6.9 7.5 8.2 9.0 10.0 10.8 11.6 12.7 14.0 15.2 17.0 18.7 20.6

5.5 6.6 7.6 8.3 9.0 9.9 11.0 11.9 12.8 14.0 15.4 16.7 18.7 20.6 22.7

6.0 7.2 8.3 9.0 9.8 10.8 12.0 13.0 14.0 15.3 16.8 18.2 20.4 22.5 24.8

6.5 7.8 9.0 9.8 10.6 11.5 13.0 14.1 15.2 16.6 18.2 19.7 22.1 24.4 26.9

to Lift Load on Belt Conveyor

150

200

250

300

350

400

500

600

700

800

900

1000

1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0

1.5 3.0 4.5 6.0 7.5 9.0 10.5 12.0 13.5 15.0

2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0

2.5 5.0 7.5 10.0 12.5 15.0 17.5 20.0 22.5 25.0

3.0 6.0 9.0 12.0 15.0 18.0 21.0 24.0 27.0 30.0

3.5 7.0 10.5 14.0 17.5 21.0 24.5 28.0 31.5 35.0

4.0 8.0 12.0 16.0 20.0 24.0 28.0 32.0 36.0 40.0

5.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0 45.0 50.0

6.0 12.0 18.0 24.0 30.0 36.0 42.0 48.0 54.0 60.0

7.0 14.0 21.0 28.0 35.0 42.0 49.0 56.0 63.0 70.0

8.0 16.0 24.0 32.0 40.0 48.0 56.0 64.0 72.0 80.0

9.0 18.0 27.0 36.0 45.0 54.0 63.0 72.0 81.0 90.0

10.0 20.0 30.0 40.0 50.0 60.0 70.0 80.0 90.0 100.0

Where:

The belt tensions developed in a belt conveyor depend on the following: 1. Motor horsepower 2. Belt speed in feet per minute 3. Drive configuration To determine tight side (T1) and slack side (T2) operating tensions, first determine the effective tension (difference between T1 and T2) from: Te = 33,000 x HP/FPM Where: Te = Effective tension HP = Motor horsepower FPM = Belt speed The slack side belt tension is calculated from Te and the drive factor Cw (from Table 7) by: T2 = Te x Cw Where: T2 = Slack side tension Te = Effective tension Cw = Drive factor from Table 7

Table 7 – Drive Factor 0 Wrap 180° 200° 210° 220° 240°

T1 = Tight side tension Te = Effective tension T2 = Slack side tension

Example: Horsepower and Tension calculation Calculate horsepower and belt tensions for a conveyor given: 1. Capacity of 300 tons per hour 2. 300 ft. conveyor length 3. 20 ft. conveyor lift 4. Belt speed of 450 feet per minute 5. Screw take-up system 6. 1805 arc of contact on drive pulley 7. Lagged drive pulley

Horsepower: From Table 5 the horsepower required to operate the belt on the level is 8.4. From Table 6 the horsepower required for lift is 6.0. The total horsepower required is 8.4 + 6.0 = 14.4. (A 15 HP motor would be selected.)

Tension: Automatic takeup Bare Lagged Pulley Pulley 0.84 0.50 0.72 0.42 0.66 0.38 0.62 0.35 0.54 0.30

Manual takeup Bare Lagged Pulley Pulley 1.2 0.8 1.0 0.7 1.0 0.7 0.9 0.6 0.8 0.6

The tight side tension is calculated from Te and T2 by: T1 = Te + T2

FEATURES/BENEFITS PAGES PT1 -2 - PT1 -

Sprockets

Short Tons Per Hour (2000 lbs.)

100

Belt Tension:

Type of pulley drive Single no snub Single with snub

300

2.7 3.3 3.8 4.2 4.6 5.0 5.5 5.8 6.2 6.8 7.6 8.4 9.2 10.2 11.1

Conveyor Components

in Feet 10 20 30 40 50 60 70 80 90 100

250

HT Synchrous Belts

Short Tons Per Hour (2000 lbs.)

Length of

The horsepower required to operate a Conveyor 100 150 200 belt conveyor depends on the following: in feet 1. Maximum tonnage to be handled 25 2.0 2.3 2.5 50 2.4 2.7 3.0 2. Length of the conveyor 75 2.8 3.1 3.5 3. Vertical lift of the conveyor 100 3.0 3.4 3.8 125 3.4 3.8 4.2 To determine horsepower required for a 150 3.7 4.1 4.6 horizontal conveyor, use Table 1 only. 175 4.0 4.5 5.0 To determine horsepower required for an 200 4.3 4.8 5.3 inclined conveyor, use Table 1 and Table 2. 225 4.6 5.1 5.7 Figure each table separately and sum the 250 4.9 5.5 6.2 results to determine total horsepower 300 5.6 6.2 7.0 required. 350 6.2 6.9 7.7 400 6.8 7.6 8.5 Note: Other factors, such as conveyor 450 7.3 8.3 9.2 plows, scrappers, and skirt boards over 500 8.0 9.0 10.1 12 feet, will require additional factors for horsepower. See conveyor design Table 2 – HP Required program or call conveyor component Lift engineering for assistance.

First calculate effective tension from: 33000 x HP 33000 x 15 Te = Te = = 1100 lbs. FPM 450 Calculate T2 from Te and drive factor Cw (From Table 7 Cw = .8) T2=Cw x Te T2=.8 x 1100 = 880 lbs. Finally calculate T1 from T2 and Te T1=880+1100=1980 lbs. T1=T2+Te * These calculations are limited to level or uphill conveyors with single drive pulley and a maximum length of 500 ft. For other systems, consult DODGE.

SELECTION/ I ENSIONS PAGE PT1 -10

O IFICATIONS/ACCESSORIES PAGE PT1 -

PT13-43

RELATE PRO UCTS PAGE PT1 -40

Engineering

Horsepower


DYNA-SYNC

NOTES

HT Synchrous Belts Sprockets Conveyor Components Engineering FEATURES/BENEFITS PAGES PT1 -2 - PT1 -

SELECTION/ I ENSIONS PAGE PT1 -10

O IFICATIONS/ACCESSORIES PAGE PT1 -

PT13-44

RELATE PRO UCTS PAGE PT1 -40


DYNA-SYNC

CONTENTS ENGINEERING/TECHNICAL BEARING ENGINEERING SECTION Vibration Frequencies of Anti-Friction Mounted Bearings. . . . . . . . . . . . . . . . PT14-2 Bearing Life Adjustment Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT14-9 (Rolling Element Bearings)

V-Belt Sheave Groove Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT14-11 Conveyor Belt FPM to RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT14-12 Material Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT14-13 GENERAL ENGINEERING SECTION

HT Synchrous Belts

PT COMPONENT ENGINEERING SECTION

Shafting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT14-15 Expansion of Shafting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT14-20 Weights/Properties of Steel Shafting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT14-21

English Standard Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT14-24 Metric Standard Measurement & Conversion . . . . . . . . . . . . . . . . . . . . . . . . . PT14-26 Common Conversion Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT14-27

Sprockets

Oil Viscosity Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT14-23

Flywheel Formulas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT14-34 Centrifugal Force . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT14-34

Torque and Horsepower Equivalents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT14-35 Overhung Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT14-35 Mathematical Equations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT14-35 Strength and Physical Properties of Various Metals . . . . . . . . . . . . . . . . . . . . PT14-36 Properties of Sections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT14-37 Coefficients of Friction (f) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT14-38

Conveyor Components

Formulas and Constants. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT14-33

Hardness Comparison . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT14-38 U.S. Standard Sheet Metal Gages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT14-38

Part Number Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INDEX-1 Keyword Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INDEX-29

PT14-1

Engineering

Trigonometric Formula . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT14-39


DYNA-SYNC

ENGINEERING Vibration Frequencies Of DODGE Anti-Friction Mounted Bearings

HT Synchrous Belts

More and more manufacturing facilities are getting involved with plant-wide preventive maintenance programs. By monitoring vibration levels of motors, pumps, fans and compressors, maintenance supervisors can predict imminent failures. Knowing that a piece of equipment is showing signs of potential failure permits scheduling of maintenance at an appropriate time and avoids the consequences of catastrophic failures. Shown on Table 1 Table 10 are vibration frequencies generated by bearing components defects. All frequencies are based on unity inner ring or cone rotation.

Frequency Cup Nick or SpaII Cone Nick or SpaIl Roller Nick or Spail

1000 x 9.249 = 9249 RPM 1000 x 11.751 = 11751 RPM 1000 x 8.068 = 8068 RPM

Roll Size Variation

1000 x.440 = 440 RPM

Since all the values on Table 1 - Table 10 are based on unity inner ring or cone rotation, the vibration due to flaws will show up at the frequencies obtained by multiplying the RPM times the factors found on the appropriate table. The resulting product will have units of REV./MIN.

How to Use the Tables If a 2-7/16 Type E pillow block is rotating at 1000 RPM, the vibration due to a failed component will show up at the following frequencies: (Table 3 , Line 6)

Table 1: All Setscrew, Eccentric & D-Lok Ball Bearing Parameters For Vibration Analysis (1-RPS) Sprockets

Series 203 204 205

S ore 1/2 - 5/8 1/2 - 3/4 7/8 - 1

S M ore

a s 8 8 9

Dia eter o a s 17/64 5/16 5/16

Pitc Dia eter 1.1506 1.3251 1.5325

ter in re enc z 3.076569 3.056675 3.582382

nner in re enc z 4.923431 4.943325 5.417618

a Spin re enc z 2.050406 2.002244 2.350042

a e enc z 0.384571 0.382084 0.398042 re

Conveyor Components

206 207 208 209

1-1/6 - 1-1/4 1-1/4 - 1-7/16 1-1/2 - 1-5/8 1-11/16 - 1-3/4

1 1-3/16 1-7/16 - 1-1/2 1-1/2

9

3/8

1.823

3.574328

5.425672

2.327814

0.397148

9 9 9

7/16 1/2 13/25

2.136 2.387 2.5591

3.578301 3.557394 3.585616

5.421699 5.442606 5.414384

2.338732 2.282266 2.359075

0.397589 0.395266 0.398402

210 211 212 214

1-15/16 - 2 2 2-1/4 2-1/4 - 2-7/16 2-11/16

1-11/16 - 1-3/4 1-15/16 - 2 2-3/16 - 2-1/4 2-7/16 - 2-1/2

10 10 10 10

1/2 9/16 5/8 11/16

2.7645 3.092 3.385 3.775

4.095677 4.090395 4.076809 4.089404

5.904323 5.909605 5.923191 5.910596

2.674068 2.657484 2.615681 2.654395

0.409568 0.409039 0.407681 0.408940

215 216 218

2-15/16

2-11/16 2-15/16 - 3 3-7/16 - 3-1/2

11 11 11

11/16 3/4 27/32

4.085 4.33 4.9199

4.574357 4.547344 4.556764

6.425643 6.452656 6.443236

2.886760 2.800062 2.829748

0.415851 0.413395 0.414251

Table 2: CC Ball Bearing Parameters For Vibration Analysis (1-RPS)

Engineering

Series 205 206 207

S at Size 15/16 - 1 1-1/8 - 1-3/16 1-1/4 - 1-7/16

209 210 211

1-11/16 - 1-3/4 1-15/16 2-3/16

a s 9 9 9

Dia eter o a s 5/16 3/8 7/16

Pitc Dia eter 1.516 1.811 2.106

ter in re enc z 3.572394 3.568194 3.565171

nner in re enc z 5.427606 5.431806 5.434829

a Spin re enc z 2.322533 2.311133 2.302987

a e enc z 0.396933 0.396466 0.396130

9 10 10

1/2 1/2 9/16

2.362 2.756 3.051

3.547417 4.092888 4.078171

5.452583 5.907112 5.921829

2.256157 2.665289 2.619817

0.394157 0.409289 0.407817

PT14-2

re


DYNA-SYNC

ENGINEERING Table 3: Type E, K, DI, and TAF Tapered Roller Bearing Parameters For Vibration Analysis (1-RPS) Mean Dia eter o o ers 0.23 0.29

Pitc Dia eter 1.774 2.084

ontact n e 17.533 16.5

re

ore Size 1-3/16 - 1-1/4 1-3/8 - 1-7/16

o ers Per o 19 20

p enc z 8.325540 8.665750

one enc z 10.674460 11.334250

o er Spin re enc z 3.797580 3.529138

1-1/2 - 1-11/16 1-3/4 - 2 ‘2-3/16

18 17 19

0.35 0.41 0.41

2.411 2.709 3.014

16 12.033 13.283

7.744100 7.241814 8.242270

10.255900 9.758186 10.757730

3.377216 3.231274 3.611184

0.430228 0.425989 0.433804

2-1/4 - 2-1/2 2-11/16 - 3 3-3/16 - 3-1/2 3-15/16 - 4

21 24 26 26

0.41 0.41 0.46 0.51

3.337 3.9 4.78 5.12

14.5 16.733 18.167 17.567

9.251011 10.791879 11.811316 11.765467

11.748989 13.208121 14.188684 14.234533

4.011931 4.707891 5.152213 4.974340

0.440524 0.449662 0.454281 0.452518

4-7/16 - 4-1/2 4-15/16 - 5 5-7/16 - 6 6-7/16 - 7

25 25 32 27

0.59 0.68 0.67 0.93

5.727 6.568 8.444 9.791

18.983 17 17.75 19.167

11.282275 11.262395 14.790895 12.288783

13.717725 13.737605 17.209105 14.711217

4.807330 4.782071 6.265507 5.221605

0.450496 0.462215 0.455140

a e enc z 0.438186 0.433287 HT Synchrous Belts

re

0.451291

Pd = Pitch Diameter N = Number of rollers Bd = Roller Diameter a = Cup Angle (contact angle)

Sprockets

Cup Frequency = N * RPM * (1 - (Bd * cos a / Pd)) / 2 Cone Frequency = N * RPM * (1 + (Bd * cos a / Pd)) / 2 Roller Spin Frequency = Pd * RPM * (1 - (Bd * cos a / Pd) ^2) / (2 * Bd) Cage Frequency = RPM * (1 - (Bd * cos a / Pd)) / 2

re

Table 4: Type C Tapered Roller Bearing Parameters For Vibration Analysis (1-RPS) Pitc Dia eter 2.251 2.604 2.848

ontact n e 14.92 11.50 15.00

p enc z 8.235801 9.235581 9.768852

one enc z 10.764199 11.764419 12.231148

o er Spin re enc z 3.566352 4.009748 4.261097

2 - 2-1/4 2-3/16 - 2-7/16 2-1/2 - 2-11/16 2-7/16 - 2-15/16 3 - 3-3/16

21 25 23 26 22

0.40 0.35 0.43 0.42 0.55

3.335 3.533 3.827 4.22 4.612

16.83 18.00 16.50 16.50 16.50

9.294571 11.322284 10.261076 11.759442 9.742225

11.705429 13.677716 12.738924 14.240558 12.257775

4.113807 5.002340 4.398352 4.978061 4.137910

0.442599 0.452891 0.446134 0.452286 0.442828

3-1/4 - 3-7/16 3-1/2 - 4 4-7/16 - 4-1/2

24 25 33

0.51 0.59 0.46

4.761 5.727 3.109

16.42 18.98 11.50

10.766982 11.282253 14.107710

13.233018 13.717747 18.892290

4.618367 4.807328 3.308310

0.448624 0.451290 0.427506

11.796028 14.203972 Pd = Pitch Diameter N = Number of rollers Bd = Roller Diameter a = Cup Angle (contact angle)

5.090519

0.453693

4-15/16 - 5 26 0.68 6.983 18.00 Cup Frequency = N * RPM * (1 - (Bd * cos a / Pd)) / 2 Cone Frequency = N * RPM * (1 + (Bd * cos a / Pd)) / 2 Roller Spin Frequency = Pd * RPM * (1 - (Bd * cos a / Pd) ^2) / (2 * Bd) Cage Frequency = RPM * (1 - (Bd * cos a / Pd)) / 2

PT14-3

re

re

a e enc z 0.433463 0.439790 0.444039

re

Conveyor Components

Mean Dia eter o o ers 0.31 0.32 0.33

Engineering

ore Size 1-3/16 - 1-7/16 1-1/2 - 1-3/4 1-15/16

o ers Per o 19 21 22


DYNA-SYNC

ENGINEERING Table 5: Special Duty Tapered Roller Bearing Parameters For Vibration Analysis (1-RPS)

HT Synchrous Belts

Mean Dia eter o o ers 0.40

Pitc Dia eter 2.563

ontact n e 11.54

re

ore Size 1-3/8 - 1-1/2

o ers Per o 16

Sprockets

one enc z 9.223298

o er Spin re enc z 3.128839

1-9/16 - 1-3/4 1-7/8 - 2 2-1/8 - 2-1/4 2-3/8 - 2-1/2 2-5/8 - 3

18 19 22 20 22

0.40 0.41 0.41 0.46 0.51

2.854 3.014 3.475 3.695 4.336

12.72 13.28 15 14.38 15.07

7.769570 8.242255 9.746381 8.794078 9.750677

10.230430 10.757745 12.253619 11.205922 12.249323

3.500820 3.611183 4.182764 3.957897 4.196146

0.431643 0.433803 0.443017 0.439704 0.443213

3-3/16 - 3-1/2 3-11/16 - 4 4-7/16 - 4-1/2

23 23 26

0.59 0.68 0.68

5.22 5.942 6.983

17.42 15.50 18

10.259806 10.231809 11.796028

12.740194 12.768191 14.203972

4.372280 4.315984 5.090519

0.446079 0.444861 0.453693

4-15/16 - 5 5-7/16 - 6 6-1/2 - 7 7-15/16 - 8

24 24 29 27

0.81 0.93 0.93 1.12

7.537 9.123 10.19 11.471

16.42 17.33 19.23 12.42

10.762960 10.832249 13.250482 12.212741

13.237040 13.167751 15.749518 14.787259

4.603028 4.858391 5.437812 5.074422

0.448457 0.451344 0.456913 0.452324

19.276067 21.723933 17.150534 19.849466 Pd = Pitch Diameter N = Number of rollers Bd = Roller Diameter a = Cup Angle (contact angle)

8.005271 6.656476

0.470148 0.463528

8-1/2 - 10 41 0.87 13.979 16.40 11 - 12 37 1.20 16.061 12.50 Cup Frequency = N * RPM * (1 - (Bd * cos a / Pd)) / 120 Cone Frequency = N * RPM * (1 + (Bd * cos a / Pd)) / 120 Roller Spin Frequency = Pd * RPM * (1 - (Bd * cos a / Pd) ^2) / (120 * Bd) Cage Frequency = RPM * (1 - (Bd * cos a / Pd)) / 120

p enc z 6.776702

re

a e enc z 0.423544

re

Table 6: All Steel Tapered Roller Bearing Parameters For Vibration Analysis (1-RPS)

Conveyor Components Engineering

ontact n e 15.50

p re enc z 12.361632

one re enc z 14.638368

o er Spin re enc z 5.673261

5.120 5.814 6.503 7.355 8.272

17.57 12.50 12.92 12.50 12

11.765488 15.170061 13.196026 14.704466 12.159067

14.234512 17.829939 15.803974 17.295534 14.840933

4.974342 6.016904 5.375340 5.989163 4.875231

0.452519 0.459699 0.455035 0.459515 0.450336

8.323 9.748 11.471

12 12.50 12.42

11.701366 14.702011 12.212741

14.298634 17.297989 14.787259

4.847026 5.977683 5.074422

0.450053 0.459438 0.452324

9 - 10 32 1.28 14.026 12.03 Cup Frequency = N * RPM * (1 - (Bd * cos a / Pd)) / 120 Cone Frequency = N * RPM * (1 + (Bd * cos a / Pd)) / 120 Roller Spin Frequency = Pd * RPM * (1 - (Bd * cos a / Pd) ^2) / (120 * Bd) Cage Frequency = RPM * (1 - (Bd * cos a / Pd)) / 120

14.571921

17.428079 5.435259 Pd = Pitch Diameter N = Number of rollers Bd = Roller Diameter a = Cup Angle (contact angle)

0.455373

ore Size 2-11/16 - 3

o ers Per o 27

Mean Dia eter o o ers 0.36

Pitc Dia eter 4.114

3-1/4 - 3-1/2 3-15/16 - 4 4-7/16 - 4-1/2 4-15/16 - 5 5-7/16

26 33 29 32 27

0.51 0.48 0.60 0.61 0.84

5-15/16 - 6 6-7/16 - 7 7-1/2 - 8

26 32 27

0.85 0.81 1.12

PT14-4

a e enc z 0.457838

re


Table 7: Spherical Roller Bearing Parameters for Vibration Analysis (1-RPS) T

ore Sizes in

S2000 nisp ere

ore

Sizes in

Sizes in

1-3/8 - 1-1/2

1-1/8 - 1-1/2

22207E1ASKM 22208E1ASKM 22209E1ASKM

1-7/16

22210E1ASKM

1-11/16

22211E1ASKM 22213E1ASKM

1-11/16 - 1-3/4 1 5/8 - 1-3/4

o ers Dia eter Per o

o

Pitc

o ers Dia eter

ontact

re

enc

nner in re

enc

Spin re

enc

a e re

enc

n e

z

z

z

z

15

0.3937

2.166

11.750

6.165339

8.834661

2.663713

0.411023

15

0.4488

2.449

10.583

6.148942

8.851058

2.639849

0.409929

9.848843

17

0.4291

2.665

9.750

7.151157

3.027139

0.420656

18

0.4331

2.858

9.083

7.653247 10.346753 3.225588

0.425180

1-15/16 - 2

1 7/8 - 2

1-15/16

2-3/16

2-3/16 - 2-1/4

19

0.4646

3.189

8.750

8.132069 10.867931 3.360826

0.428004

2-3/16

2 -7/16

2-3/8 - 2-1/2

18

0.5827

3.795

9.083

7.635432 10.364568 3.181534

0.424191

2-11/16 - 3

2-11/16 - 3

20

0.5748

4.197

8.250

8.644623 11.355377 3.583768

0.432231

19

0.6535

4.48

8.167

8.128283 10.871717 3.356234

0.427804

22215E1ASKM 2 7/16 - 2-1/2 22216E1ASKM 2-11/16 - 2-3/4 22217E1ASKM

2-15/16 - 3

22218E1ASKM

3-3 /16

22220E1ASKM 3-7 /16 - 3-1 /2 22222E1ASKM

3-1 5/16 - 4

22224E1ASKM

4-3/16

22226E1ASKM 4-7/16 - 4-1/2 22228E1ASKM

4-15/16 - 5

22230E1ASKM

5-3/16

22232E1ASKM 5-7/16 - 5-1/2 22234E1ASKM

ter in

peria

3-7 /16

3-3/16 - 3-1 /2

0.7323

4.764

8.417

7.631462 10.368538 3.177554

0.423970

0.7795

5.079

8.833

7.635107 10.364893 3.182930

0.424173

3-1 5/16 - 4

3-1 1/16 - 4

18

0.878

5.705

9.000

7.631952 10.368048 3.173794

0.423997

4-7/16

4-7/16 - 4-1/2

17

1.0197

6.287

9.417

7.139947

3.003844

0.419997

18

1.0472

6.819

9.417

7.636487 10.363513 3.181095

0.424249

4-15/16

4-15/16 - 5

18

1.1181

7.307

9.750

7.642733 10.357267 3.193282

0.424596

5-7/16 - 5-1/2 5-15/16 - 6

5-15/16 - 6

22236E1ASKM 6-7/16 - 6-1/2

18 18

6-7/16 - 7

9.860053

18

1.2165

7.933

9.583

7.639139 10.360861 3.186035

0.424397

18

1.315

8.559

9.500

7.636209 10.363791 3.179646

0.424234

18

1.4094

9.189

9.667

7.639189 10.360811 3.185371

0.424399

17

1.5827

9.74

9.833

7.139085

2.998143

0.419946

18

1.5591

10.157

9.417

7.637116 10.362884 3.182632

0.424284

9.860915

22238E1ASKM

6-15/16 - 7

20

1.4961

10.669

10.667

8.621944 11.378056 3.497892

0.431097

22240E1ASKM

7-3/16

19

1.6142

11.021

10.833

8.133372 10.866628 3.343119

0.428072

22244E1ASKM

7-1/2 - 8

19

1.8504

12.48

10.833

8.116546 10.883454 3.300728

0.427187

23048KMB

8-7/16 - 9

29

1.1417

12.008

9.333

13.139616 15.860384 5.212536

0.453090

23052KMB

9-7/16 - 9-1/2

27

1.378

13.228

9.667

12.113633 14.886367 4.749092

0.448653

23056KMB

9-15/16 - 10-1/2

28

1.378

13.976

9.333

12.637908 15.362092 5.023115

0.451354

Outer Ring Frequency = N * RPM * (1 - (Bd * cos a / Pd)) / 120

Pd = Pitch Diameter

Inner Ring Frequency = N * RPM * (1 + (Bd * cos a / Pd)) / 120

N = Number of rollers Bd = Roller Diameter

Cage Frequency = RPM * (1 - (Bd * cos a / Pd)) / 120

a = Contact Angle

Engineering

Roller Spin Frequency = Pd * RPM * (1 - (Bd * cos a / Pd) ^2) / (120 * Bd)

HT Synchrous Belts

S

Sprockets

earin Series

S

Conveyor Components

asic

DYNA-SYNC

ENGINEERING

PT14-5


DYNA-SYNC

ENGINEERING Table 8: DODGE USAF Air Handling Spherical Roller Bearing Parameters For Vibration Analysis (1-RPS)

HT Synchrous Belts

ore Size

asic earin Series

1-7/16 1-11/16

Sprockets

10.0000 9.2500

ter in re enc z 7.231287 8.180471

nner in re enc z 9.768713 10.819529

o er Spin re enc z 3.225462 3.484413

0.425370 0.430551

3.0921 3.7110 4.1098 4.3638

8.9200 9.2500 8.3300 8.2500

7.698000 8.157076 9.156413 8.705275

10.302000 10.842924 11.843587 11.294725

3.342963 3.421302 3.802922 3.757794

0.427667 0.429320 0.436020 0.435264

4.6811 4.9602 5.5606 6.1559

8.5000 8.8300 9.0000 9.4200

8.669157 8.666651 8.204572 8.181428

11.330843 11.333349 10.795428 10.818572

3.649937 3.639636 3.554256 3.485342

0.433458 0.433333 0.431820 0.430601

8.194401 10.805599 8.209178 10.790822 8.211024 10.788976 Pd = Pitch Diameter N = Number of rollers Bd = Roller Diameter a = Contact Angle

3.519683 3.557887 3.565861

0.431284 0.432062 0.432159

o ers Per o

Dia eter o o ers

Pitc Dia eter

22209E1K 22210E1K

17 19

0.3937 0.3937

2.5976 2.7976

1-15/16 2-3/16 2-7/16 - 2-1/2 2-11/16 - 2-3/4

22211E1K 22213E1K 22215E1K 22216E1K

18 19 21 20

0.4528 0.5315 0.5315 0.5709

2-15/16 - 3 3-3/16 3-7/16 - 3-1/2 3-15/16 - 4

22217E1K 22218E1K 22220E1K 22222E1K

20 20 19 19

0.6299 0.6693 0.7677 0.8661

4-3/16 22224E1K 19 0.9252 6.6382 4-7/16 - 4-1/2 22226E1K 19 0.9843 7.1358 4-15/16 - 5 22228E1K 19 1.0630 7.7232 Outer Ring Frequency = N * RPM * (1 - (Bd * cos a / Pd)) / 120 Inner Ring Frequency = N * RPM * (1 + (Bd * cos a / Pd)) / 120 Roller Spin Frequency = Pd * RPM * (1 - (Bd * cos a / Pd) ^2) / (120 * Bd) Cage Frequency = RPM * (1 - (Bd * cos a / Pd)) / 120

ontact n e

9.5800 9.9200 9.6700

Conveyor Components Engineering

PT14-6

re

a e enc z


Table 9: Split-Spherical Roller Bearing Parameters For Vibration Analysis ore Size 2-3/16 2-7/16

asic earin Series 22213SS 22215SS

o ers Per o 17 18

Dia eter o o ers 0.559 0.551

Pitc Dia eter 3.414 3.748

ontact n e 9.000 9.083

ter in re enc z 7.125120 7.693012

nner in re enc z 9.874880 10.306988

o er Spin re enc z 2.973241 3.328155

2-11/16 2-15/16 3-3/16 3-7/16

22216SS 22217SS 22218SS 22220SS

19 20 19 18

0.579 0.575 0.654 0.780

3.950 4.153 4.435 5.079

8.667 8.250 8.167 8.833

8.124082 8.630263 8.114365 7.635107

10.875918 11.369737 10.885635 10.364893

3.341232 3.544783 3.321078 3.182930

0.427583 0.431513 0.427072 0.424173

3-15/16 - 4 4-3/16 4-7/16 - 4-1/2

22222SS 22224SS 22226SS

18 17 18

0.878 1.110 1.047

5.634 6.203 6.727

9.000 9.417 9.417

7.614712 6.999864 7.617839

10.385288 10.000136 10.382161

3.132415 2.707845 3.136146

0.423040 0.411757 0.423213

4-15/16 5-3/16 5-7/16 5-15/16 - 6

22228SS 22230SS 22232SS 22234SS

18 18 18 18

1.118 1.217 1.315 1.409

7.202 7.822 8.442 9.059

9.750 9.583 9.500 9.667

7.622945 7.619828 7.617307 7.619661

10.377055 10.380172 10.382693 10.380339

3.145244 3.139355 3.134123 3.138182

0.423497 0.423324 0.423184 0.423314

6-7/16 - 6-1/2 6-15/16 - 7 7-3/16 7-1/2 - 8

22236SS 22238SS 22240SS 22244SS

18 18 16 16

1.409 1.559 1.579 1.752

9.059 10.021 10.716 11.257

9.667 9.417 9.417 9.500

7.619661 7.618619 6.837308 6.771984

10.380339 10.381381 9.162692 9.228016

3.138182 3.138004 3.322243 3.136916

0.423314 0.423257 0.427332 0.423249

8.083 8.417 8.667

8.843406 11.156594 9.780985 12.219015 8.844916 11.155084 Pd = Pitch Diameter N = Number of rollers Bd = Roller Diameter a = Contact Angle

4.222831 4.408432 4.222170

0.442170 0.444590 0.442246

Conveyor Components

Sprockets

HT Synchrous Belts

re

Engineering

8-1/2 - 9 23048SS 20 1.307 11.189 9-1/2 23052SS 22 1.339 11.949 10 23056SS 20 1.539 13.175 Outer Ring Frequency = N * RPM * (1 - (Bd * cos a / Pd)) / 12 0Inner Ring Frequency = N * RPM * (1 + (Bd * cos a / Pd)) / 120 Roller Spin Frequency = Pd * RPM * (1 - (Bd * cos a / Pd) ^2) / (120 * Bd) Cage Frequency = RPM * (1 - (Bd * cos a / Pd)) / 120

a e enc z 0.419125 0.427390

DYNA-SYNC

ENGINEERING

PT14-7


DYNA-SYNC

ENGINEERING Table 10: USDAF Spherical Roller Bearing Parameters For Vibration Analysis (1-RPS)

HT Synchrous Belts Sprockets

9.5 9.333 9.5

ter in re enc z 12.108065 12.627248 12.144010

nner in re enc z 14.891935 15.372752 14.855990

o er Spin re enc z 4.732011 4.983368 4.860109

0.448447 0.450973 0.449778

17.793 18.587 19.822

9.333 9 9.167

12.655257 13.619458 13.106938

15.344743 16.380542 15.893062

5.089157 5.320311 5.090472

0.451973 0.453982 0.451963

1.929

20.609

9

13.613287

16.386713

5.296232

0.453776

23 24

1.693 1.732

13.914 14.711

12.5 12

10.133894 10.618053

12.866106 13.381947

4.051285 4.190502

0.440604 0.442419

23160K 23164K 23168K 23172K

23 23 23 24

1.89 2.087 2.244 2.244

15.923 17.044 18.272 19.077

12.333 12.833 12.833 12.333

10.166494 10.127024 10.122953 10.621032

12.833506 12.872976 12.877047 13.378968

4.155793 4.025170 4.012925 4.194537

0.442021 0.440305 0.440128 0.442543

13-15/16 - 14

23176K

25

2.323

19.833

12

11.067894

13.932106

4.212801

0.442716

8-15/16 - 9 9-7/16 - 9-1/2

23248K 23252K

20 19

1.929 2.126

13.523 14.745

14 14

8.615913 8.170935

11.384087 10.829065

3.438035 3.399907

0.430796 0.430049

10-7/16 - 10-1/2 10-15/16 - 11 11-15/16 - 12 12-7/16 - 12-1/2

23256K 23260K 23264K 23268K

20 20 20 20

2.126 2.323 2.441 2.638

15.537 16.706 17.878 19.048

13.583 13.833 14 14.167

8.669925 8.649811 8.675192 8.657198

11.330075 11.350189 11.324808 11.342802

3.589401 3.530230 3.597751 3.545213

0.433496 0.432491 0.433760 0.432860

ore Size

asic earin Series

o ers Per o

Dia eter o o ers

Pitc Dia eter

10-15/16 - 11 11-7/16 - 12 12-7/16 - 12-1/2

23060K 23064K 23068K

27 28 27

1.575 1.575 1.732

15.066 15.85 17.007

12-15/16 - 13-1/2 13-15/16 - 14 15

23072K 23076K 23080K

28 30 29

1.732 1.732 1.929

15-3/4

23084K

30

9-7/16 - 9-1/2 10-7/16 - 10-1/2

23152K 23156K

10-15/16 - 11 11-15/16 - 12 12-7/16 - 12-1/2 13-7/16 - 13-1/2

ontact n e

Conveyor Components

Outer Ring Frequency = N * RPM * (1 - (Bd * cos a / Pd)) / 120 Inner Ring Frequency = N * RPM * (1 + (Bd * cos a / Pd)) / 120 Roller Spin Frequency = Pd * RPM * (1 - (Bd * cos a / Pd) ^2) / (120 * Bd) Cage Frequency = RPM * (1 - (Bd * cos a / Pd)) / 120

Engineering

PT14-8

Pd = Pitch Diameter N = Number of rollers Bd = Roller Diameter a = Contact Angle

re

a e enc z


Mounted Bearings Life Adjustment Factor The life adjustment factors for reliability of Table 11 are recommended.

Bearing life calculated according to the RATING LIFE formula assumes proper application conditions. If lubrication is not adequate, loading unusual, or temperatures extreme, the ability of the bearing to attain or exceed the RATING LIFE is seriously impaired. Section 1.4 contains some basic recommendations concerning the effect of unusual application conditions on bearing life. 1.2 LIFE ADJUSTMENT FACTOR FOR RELIABILITY. Bearing life estimated in accordance with this standard is RATING LIFE; i.e., the life associated With 90% reliability or the life which 90% of a group of apparently identical bearings in a given application under similar conditions of load and speed will complete or exceed. While RATING LIFE has proven useful over a period of years as a criterion of performance, some applications require definition of life at reliabilities greater than 90%.

Life Adjustment Factor for Reliability a1

90

L10

1

95

L5

0.62

96

L4

97

L3

98

L2

0.33

99

L1

0.21

( Rating ) Life

0.53 0.44

1.3 LIFE ADJUSTMENT FACTOR FOR MATERIAL. For bearings, which incorporate improved materials and processing, the L10 (as previously calculated in Selection Procedure) must be adjusted by a factor a2. Factor a2 depends upon steel analysis, metallurgical processing, forming methods, heat treatment and manufacturing methods in general. Bearings fabricated from consumable vacuum remelted steels and certain other special analysis steels have demonstrated extraordinarily long endurance. These steels are of exceptionally high quality, and bearings fabricated from these are usually considered special manufacture. As such, a2 values will not be specified for such steels in this discussion. Generally, a2 values for such steels can be obtained from the bearing manufacturer.

Engineering

To determine bearing life with reliabilities other than 90% (as previously calculated from the Selection Procedure) the L10 must be adjusted by a factor a1, such that Ln=a1 x L10.

Ln

Sprockets

Reliability %

Some bearing steels; e.g., vacuum-melted steels, and improved processing techniques, permit manufacture of bearings which offer endurance greater than that calculated by the RATING LIFE formula. Section 1.3 recommends methods to incorporate life adjustment factors for bearing materials into the life formula.

HT Synchrous Belts

Table 11: Life Adjustment Factors For Reliability

Conveyor Components

1.1 GENERAL. For certain applications, it is desirable to specify life for reliability other than 90%. In such cases a life adjustment factor for reliability may be applied to the RATING LIFE. Section 1.2 discusses life adjustment factors for reliability.

DYNA-SYNC

ENGINEERING/TECHNICAL

PT14-9


DYNA-SYNC

ENGINEERING/TECHNICAL 1.4 LIFE ADJUSTMENT FACTOR FOR APPLICATION CONDITIONS. Application conditions which affect bearing life include: 1. 2.

3. HT Synchrous Belts Sprockets Conveyor Components

*

1.5 FACTOR COMBINATIONS. A fatigue life formula embodying the foregoing life adjustment factors is: For Ball Bearings:

Lubrication. Load distribution (including effects of clearance, misalignment, housing, and shaft stiffness, type of loading and thermal gradients). Temperature. Consideration of (1.2) and (1.3) above requires analytical and experimental techniques beyond the scope of this discussion, therefore, the user should consult the bearing manufacturer for evaluations and recommendations. In most bearing applications, lubrication serves to separate the rolling surfaces; i.e., rolling elements and raceways; to reduce retainer-rolling elements and retainer-land friction and sometimes to act as a coolant to remove frictional heat generated by the bearing. If all limitations and qualifications specified by this discussion are observed, then the life adjustment application factor for bearings which are adequately lubricated is 1; i.e., a3=1. Operating conditions where a3 might be less than 1 include: a. exceptionally low values of Ndm (rpm times bore diameter in mm); e.g., Ndm 1000. b. Lubricant viscosity less than 20.4 centistokes (100 SSU) at operating temperature. c. Excessively high operating temperatures. When a3 is less than 1, it may not be assumed that the deficiency in lubrication can be overcome by using an improved steel.

L n = a 1 x a 2 x a3

3

( CP* ) x (16,667) RPM

For Tapered Roller Bearings: C90 * 10/3 x P For Spherical Roller Bearings: C * 10/3 L n = a1 x a 2 x a3 x P Ln = a 1 x a 2 x a 3

(

)

(1,5000,000) RPM

(16,667) RPM Indiscriminate application of the life adjustment factors in this formula may lead to serious over-estimation of bearing endurance, since fatigue life is only one criterion for bearing selection.

( )

Care must be exercised to select bearings which are of sufficient size for the application. Undersizing of shaft and housing structures by using bearings which appear adequate from a life standpoint could lead to misalignment and fitting problems which could invalidate the formulas in this discussion.

C = Basic Load Rating computed in accordance with ABMA-ANSl Standards. C90 = C x.259

Engineering

PT14-10


V-Belt Drive Formulas V-belt tensioning In cases where tensioning of a drive effects belt pull and bearing loads, the following formulas may be

DYNA-SYNC

ENGINEERING/TECHNICAL

used. T1-T2

000

(HP)

T1

( GHP )

41 2 0

T1 HP

T1 T2 HP

T1 T2

000 2 -G

( GHP )

T2

000 1 2 -G

HT Synchrous Belts

G

( GHP )

T2 HP

T1 T2 HP

G G Belt Speed T1/T2

1 1-0 G A

P

T1/T2

2

T1 T2

P

2 2

P

-

Table 12: Arc of Contact Correction Factors G and R D-d C 00 10 20 0 40 0 0 0

Small Sheave Factor Arc of G Contact 1 0 1 00 1 4 1  1  1  4 1 1 14  1 1 

Factor R

D-d C

1 000

0 0 1 00 1 10 1 20 1 0 1 40 1 0

0 4

Small Sheave Factor Arc of G Contact 1  12  120 2 1 0 0 10   1 0 

T

12

Table 13: Allowable Sheave Rim Speed Rim Speed in Feet per Minute 00 000 10 000

Sheave Material

Factor R

C

1

S

I I

Note: A

I C

00 0 14 1

C C

Bearing Load Calculations To find actual bearing loads it is necessary to know machine component weights and values of all other forces contributing to the load. Sometimes it becomes desirable to know the bearing load

imposed by the V-belt drive alone. This can be done if you know bearing spacing with respect to the sheave center and shaft load and apply it to the following formulas:

Overhung Sheave

Sheave Between Bearings

Load at B, lbs. = Shaft Load X (a + b) a b Load at A, lbs = Shaft Load X a

Load at D, lbs. = Shaft Load X c c+d Shaft Load X d Load at C, lbs = c+d

Where: a and b = Spacing, inches

Where: c and d = Spacing, inches PT14-11

Conveyor Components

S

Engineering

12 0

Sprockets

G


DYNA-SYNC

ENGINEERING/TECHNICAL Nominal V-Belt Cross Sections Table 14: Nominal V-Belt Cross Sections Industry Standard Description

Belt Section L 4L HT Synchrous Belts

W

FHP S

L N

T A B C

C

Width W, in Inches / 1/2

Thickness T, in Inches / 2 /1

21/ 2 / / 1

/ /1 1 / 2 2 / 2

1/2 21/ 2 /

/1 1 / 2 1 / 2

1-1/4

/4

Sprockets

Conveyor Belt FPM to RPM Pulley Dia. Inches

FPM 100

150

4 4

2

Conveyor Components

200

250

300

350

400

500

12

1 11

1 1 14

22 1

2 4 1 1

2

2

11

1 4 111

1 12 10

1 1 1 1 11 10

10 12 14 1

2

4

2 24

41

1

21

2

20 24 0

1 1 1 11

2 24 1 1

2 2 21

4 40 2 2

42 4

14 12

1 1

2 20

4 0

11 10

14 1

1 1

4 4

0 0

2 2

42

4

1

4

4

4 1 42

4 2 2 24

2

4 40

2

Engineering

RP

I R

PT14-12

800

44

0

900

1000

42

4

2

22 1 1 1 4 14

2 22 1 1 1

0 2 4 21 1 1

44 2 24 21

2 2

12

14

1 0

1 1

212

11

1 4 111

1 12 102

1 2 14 11

4

4

1 1 1 12 10

4

2 2

1 0

4

1 4

4 4

21 2 2 42 1 22 2 2 For values not shown use formula below: SF 2 1 RP SF S P P

700

4

0 4

2 2

600

4 4

1

2 1


1 0- 0 4 - 0 0 0 - 120 4 - 0 20 - 2 - 40 4 - 0 -4 4 0 0 - 40 40 - 0 10 - 20

O S S S C C P P R

0 - 120 0-4 0-4 0 4 - 40 0- 0 0- 0 00- 0 1 2 - 0 40 0- 0 2

C C C N C F P F C G G C B B I C C P F L

P P

O C F L A A B B N

C L C L S

F R

B B

L P P

C C G O S

G O C

S

100 -120 - 0 0 -100 01 - 0 12 - 140 40 100 - 120 00- 0 0- 0 0- 0 4 - 0 - 40 20 - 2 0 - 40 22 - 0 2 - 2 2 -4 112 1 0 120 - 1 0 -1 4

4    0 0 4  4  4  4  40  4  4   4  2  2   2   2  4  4  4  4     4  4  2   2   4    4  4        0    4   2   4   0 0  0 4  0

10-12

C C C C C C C C C C C C

S S G

4 0 40 - 4 2- 40 -L N C H

E 2 10-1 20 -10

11-1

20-2 20-2 20 20-22 1 -20 1 1 1 1 10-1 1 20-22 20 12- 0 20 1

L P E E E F E E S F L F F F S F F F F F F L F R F S L F S R G G A G B F G B G B G A F G P G G L G F G P G O G S G G G L G G H L H P H H S H S I C I O I O O P I S I S

PT14-13

-L L

1 -2 40- 4 12 - 40 40 0-110 0-120 11- 14 0-100 4 0- 0 -110 022 40- 0 0-100 0-100 - 40 40- 0 4 2 - 40 0- 40 0-110 0- 0 0- 0 100-110 2 0 0 4 0-100 0-100 40 1 0 -1 0 40 0 10 0-100 100-120 0-100 - 0 2 - 0 2 - 0 - 40 140-1 0 120-1 0 120-140 0120-140

2      4   4        40  40 2  2    40 40 0 2   4  20 4  4    0  2  10  10 2    2   2        0 0  4  4  20     

RECOMMENDED MAXIMUM INCLINATION (DEG) 10 22 1 1 22 20 22 20 2 20 1

12 21

20-22

Sprockets

G L P

DENSITY (LB/fT3)

MATERIAL

ANGLE OF REPOSE (DEG)

Conveyor Components

A A A A A A A A A A A B B B B B B B B B B B B B B B B B B B B C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C

DENSITY (LB/fT3)

RECOMMENDED MAXIMUM INCLINATION (DEG)

1 -1 1 21

1 -20 1 -1

Engineering

MATERIAL

ANGLE OF REPOSE (DEG)

DYNA-SYNC

Table 15: Material Characteristics

HT Synchrous Belts

ENGINEERING/TECHNICAL


DYNA-SYNC

ENGINEERING/TECHNICAL Table 16: Material Characteristics MATERIAL

C

HT Synchrous Belts

L L L L L L L L L L L L L

O O S S

C

A G H P L P C S

O O S Sprockets

C F G

DENSITY (LB/fT3) 0 0 1 0-2 0 0-1 0 1 0-1 0 240 - 2 0 4 040 0 - 40 0 - 100 - 0 4 - 0 0 - 40 040 - 0 2 - 0 0- 40 12 - 140 120 0 2 00 20 1

F P O

Conveyor Components Engineering

N N -C S O O O R O C O A C O S G O S P P S P S P N S P P F P R C P P C P N P S P P G P L P P L S R H R R R G R C

2 20 - 0 - 0 100 - 110 1 0 0-1 0 2 20 0 0 0- 0 0 40 - 0 -4 1 - 20 4 - 0 0- 0 0 - 100 0- 0 120 - 1 0 - 0 4 4 40 - 4 1 - 14 120 - 1 0 - 100 0- 0 4 - 0 40 - 4 100 - 1 0

ANGLE OF REPOSE (DEG)   0 40 4    40 40 40  4  2   40  0 4   40   0   20   4  40  40 0   2   4     20   0   0  2  4  0 4  2   2  2  20   0

RECOMMENDED MAXIMUM INCLINATION (DEG) 1

2 21 1 20 1 20

2

MATERIAL

R R R R S S S S S S S S S S S S S S S S S S S S S S S S S S

P G

S

C C F L F

F R

R S S B C G B G G G L C

F

A A A

B H L A N P

S

G G C

10

0 2

S S S S S T T T T T T T T

P C T C G G C

R

L P G S L S S C L S C G C O G O

PT14-14

DENSITY (LB/fT3)

ANGLE OF REPOSE (DEG)

02 42 - 4 - 40 04 0- 0 110 - 1 0 0 - 110 0 - 100 100 - 110 0- 0 10 - 2 12 - 1 0 4 0- 0 0 - 100 - 0 4 0- 0 00 - 100 0- 0 1 - 0 10 - 2 0 20 2 0- 0 00 - 40 4 - 0 2 -4 100 - 1 0 0 - 120 01 -1 00- 0 120 - 140 0- 0 140 0- 0 14 1 -2 1 - 110 100 - 110 20 - 0 -4 4 40 - 4 20 - 0 10 - 0 1 0 10 -

 4  2  20 0   4    0  0 4    2  40  2  2  4  0 0 0  20 0   24   2  2   4  4   40 4     20  4  4  4  4    0  2   2  4   4 

RECOMMENDED MAXIMUM INCLINATION (DEG) 22 1 21 1 -22 11 20-22 1 -1 22 24 22

22 10 1 -1 20-22 1

1 22 11 1 -1 12-1 12 1

1 -1

12 2 22


Shaft Size Up to 1-1/2” Over 1-1/2 to 2-1/2”

Plus .000 .000

Minus .002 .003

Over 2-1/2 to 4” Over 4 to 6” Over 6 to 8”

.000 .000 .000

.004 .005 .006

Over 8 to 9” Over 9”

.000 .000

.007 .008

Special Shafting-While standard shafting is suitable for most installations, special shafting is sometimes required for certain chemical, temperature or physical requirements. Such materials as high carbon steel, alloy steel, stainless steel, brass, Monel metal, etc., can be furnished plain or heat treated. Stepped, flanged, hollow or other special forms are available.

Table 18: Shaft Tolerances Shaft Size Up to 1-1/2”

Tolerance, Inches +.0000 -.0005”

Special shafting should be avoided in favor of standard shafting wherever possible because special shafting is usually considerably more expensive and requires a greater length of time to obtain, which is an especially important consideration should quick replacement ever become necessary.

1-5/8 to 4” +.000 -.001” 4-7/16 to 6” +.000 -.0015” 6-7/16 to 8” +.000 -.002” Table 18 lists the recommended tolerances for all setscrew locking, eccentric locking and D-LOK locking ball and roller bearings

Ordering Shafting-Standard shafting can be obtained from most supply houses and dealers who handle power transmission material.

Table 19: Shaft Tolerances Shaft Size Up to 1-1/2” 1-9/16 to 2-1/2” 2-5/8 to 4”

Tolerance, Inches +.000 -.002” +.000 -.003” +.000 -.004”

4-3/16 to 6” +.000 -.005” 6-7/16” and above +.000 -.006” Table 19 list the recommended tolerances for all tapered adapter sleeve ball and roller bearings

Turning Down Shaft Ends-When necessary to turn down shaft ends, use as large a fillet as possible to keep the stress concentration to a minimum. The radius of this fillet should preferably be not less than the difference in the two diameters joined by the fillet. The fillet should be finished and polished as smoothly as possible to avoid scratches which might start cracks and failure of the shaft by fatigue.

Selection of Shaft Diameters Table 20 thru Table 23 inclusive can be used to find approximate shaft diameter for various service conditions For greater accuracy use chart under heading “Combined Torsion and Bending of Standard Shafts” (PT14-19).

DYNA-SYNC

When necessary to use other than standard shafting, find the required diameter for standard shafting as outlined above and multiply by proper factor shown in Table 24 , under heading “Factors for Shafting Other than Standard Shafting.”(PT14-18). Engineering

Tables and chart are based upon a safe shear stress of 6,000 pounds per square inch for standard keyseated shafting. Be generous in the selection of shaft diameters as

liberal diameters not only reduce deflection and vibration but also generally increase bearing life.

HT Synchrous Belts

Standard Shafting-Table 17 indicates standard shafting is cold drawn in the smaller sizes and turned and polished in the larger diameters. It has a smooth surface, is commercially straight and is readily machinable; suitable and recommended for general power transmission and material handling service.

Table 17: Typical Commercial Shaft Tolerances

Sprockets

Shafting

Conveyor Components

ENGINEERING/TECHNICAL

PT14-15


DYNA-SYNC

ENGINEERING/TECHNICAL Selection of Shaft Diameters (Cont’d) Table 20: No Bending Moment (Shafts without pulleys, sprockets or gears - Torsion only) Shaft Size

HT Synchrous Belts

1 /1 1- /1

25 0 0 0 0

50 0 0 1 0

1- /1 1-11/1 1-1 /1 2- /1

1 0 2 20 0 4 0

2 0 4 10 0 0 0 0 11 10 12 40 1 0 1 20 1 4 40 0 0 11 20 1 40 1 0 1 0 20 20 22 40 24 0 2 0 10 10 1 0 1 0 20 0 2 0 2 10 0 0 0 0 40 0 14 0 1 0 24 40 2 0 4 20 10 44 4 0 0

2- /1 2-11/1 2-1 /1

0 1 0 20 20 2 0 40 0 4 0 1 10 2 10 20 4 0 4 40 40 11 0 2 0 40 4 0 20 1 2 0

- /1 -1 /1 4- /1

1

75 1 10 2 0

100 1 0 10

125 1 0 0

Horse Power at Various Revolutions per Minute 150 175 200 225 250 275 300 350 400 500 600 700 800 900 2 0 2 0 40 0 4 20 4 0 0 10 0 20 10 0 12 0 1 0 4 0 40 20 0 0 0 10 0 12 0 1 0 1 0 21 0 2 2 10

0

2 0 40 0

0 4 0 11 0 114 142 1 1 1 0 122 1 204 24

1 2 1 2

0 1 40 22 20 2 0 1 40 0 44 0 4 0 4 0 0 40 20

4 10 0 0 0 4 40 1 20 4 0 10 2 0 1 0 0 0 0 10 12 14 4 0 10 11 1 0 142 1 1 1 1 22 2

1 0 2

1 2 40

20 1 44

22 42 4 0

2

0 0 0 44 40 4 0 0 0 2 0 1 0 0 0 0 1 0 10 10 122 0 11 1 1 1

1 1 1 2

0

1 2 21 2 4 4

4

0

2

21 2 0 1 1

4 0

1

1 2

114

0 12 1 0

24 2 42 102 14 0

Sprockets

Table 21: Limited Bending Moment (Pulleys, sprockets or gears near bearings. Ordinary line shafts.)

Conveyor Components

Shaft Size

25

50

1 /1 1- /1 1- /1 1-11/ 1-1 /1

0 20 0 0 0 0 1 40 2 20

0 0 1 1 0 2 0 4 0

20

0

2- /1 2- /1 2-11/1 2-1 /1 - /1 -1 /1 4- /1 4-1 /1 - /1 -1 /1 -1/2

75 0 1 2 4

100

0 0 0 0 0

1 2

0

1

125

Horse Power at Various Revolutions per Minute 150 175 200 225 250 275 300 350 400

1

0 1

0 22 0 2 10 2

0

2 0

1 0 1 22 0 2 1 0 10 40 0 4 10 4 12 10 1 10 24 20 0 20 0 42 0 4 40 4 40 0 0 0 1 0 2 0 1 0 0 4 40 0 20 1 10

0

0

600

700

800

900

1 20 1 0 1 0 2 2 0 2 0 2 0 0 4 10 10 10 10 20 20 2 0 10 0 4 10 4 0 20 0 20 0 0 10 40 12 0 14 0 1 0 1 0 0 4 0 0 40 40 0 20 10 10 11 10 12 0 14 0 1 0 22 20 2 0 2 0 0 0 40 0 10 40 11 0 1 40 14 0 1 40 1 0 20 0 2 0 2 0 0 41 0 4 0 0 11 0 1 0 1 0 1 10 20 40 22 0 24 0 2 20 1 0 20 4 0 4 40 40 2 0 1 0

4 0

12 0 2 0 1 2 4

500

100

1 112 1 0

0 0 0 0 0 10 4 10 114 1 10 1 1 1 0 1 0 1 22 2 2 200 2 0 00 0

1 0 1 1

1 2

2 1 42

2 42

1 1

4

101 1 2 21 00 400 22 4

11 1 1 24

12 1 0 2 2

4 1

01 2

Engineering

PT14-16

0 0 0 0

10 4

0

2 20

20

0

4 10 20 2 20 0 20 10 2 0 4 0 0 121 14 4 0 110 12 1 1

1 20 2 412 1

1 1 22 2 4 0 01

1 40

102

1 2 1 2 01 1 11

202 04 4 00 01

2

1 0 104 144 1 2 2

12 1 221

11 1 2 21 2 4

0 4

4 40 4 0 2 0 44 2 1 0 0 00 10 0 1200 1 0 1002 1202 140 1 0 1 04

1044 1 0 1 1 2 20 1 1 10 20 2 2 4 2

2 4 0


Table 22: Heavy Bending Moment. (Use for main or important shafts.) Shaft Size 1-11/1 1-1 /1 2- /1 2- /1 2-11/1 2-1 /1 - /1 -1 /1 4- /1 4-1 /1 - /1 -1 /1 -1/2

25 50 0 0 1 0 1 0 2 0 1 0 0 2 0 40 0 20 4 0 40 0 1 10 11 40 22 0 1 0 2 0 22 0 4 0 0

-1/2 -1/2 -1/2 10

1 4

102 12 1 1 1 22 2 2 20

0 0 114 1 1 0 1

75 2 0 4 0 10 10 0 14 10 22 0 4 20 4 0 0 0 11 1 1 2 2 2 4 40 4 0

Horse Power at Various Revolutions per Minute 100 125 150 175 200 225 250 275 300 350 0 4 40 0 20 10 0 0 10 0 12 0 40 0 10 0 10 0 12 20 1 0 14 0 1 0 1 0 0 11 0 1 0 1 0 1 0 1 0 21 0 2 40 2 40 10 0 1 0 1 20 1 0 21 0 24 0 2 2 0 2 40 0 14 0 1 10 21 0 2 40 2 2 0 20 0 4 0 0 0 1 0 2 0 2 40 10 0 42 0 4 0 2 10 0 0 0 0 0 4 0 10 0 0 0 0 0 1 10 10 4 0 40 0 1 0 102 114 12 1 1 0 1 0 114 1 0 14 1 1 1 22 0 112 1 1 1 0 202 22 24 2 0 1 120 1 0 1 0 210 240 2 0 00 0 0 420 1 1 2 4 2 1 2 1 4 0 4 4 20 2 0 410 4 2 1 4 1 1 2 20 4 44 1 41 0 1 4 4 2 1 0 4 1104 2 4 4 0 1 10 114 1 40 4 4 0 1 10 114 12 1 1 0 4 1 1 4 10 0 122 1 14 1 1 0 41 01 1 1122 12 2 1442 1 0 1 1 2 2244 4 4 1121 1 0 14 1 2 1 20 224 2 1

400 500 600 14 0 1 0 21 0 21 0 2 10 2 0 1 0 10 4 0 4 0 4 10 4 0 2 0 10 0 4 0 11 121 1 1 1 2 1 2 22 2 2 1 2 2 0 4 0 40 4 0 01 21 2 2 21 102 12 2 102 12 2 1 12 2 1 1 1 1 1 14 22 1 22 2 21 1 2 2 2 1 2 20 4 2 1 44

700 800 2 10 2 0 4 0 4 0 2 0 0 0 101 11 1 2 1 1 212 24 1 4 22 0 20 41 1 10 12 2 14 1 4 1 20 2 220 2 24 2 0 0 21 4 1 4 2 44 1 0 2

900 2 0 4 0 0 40 40 1 0 1 0 2 410 10 10 2 140 1 4 2 0 2 44 41 4 0 1 1

Sprockets

Selection of Shaft Diameters (Cont’d)

HT Synchrous Belts

DYNA-SYNC

ENGINEERING/TECHNICAL

1-11/1 1-1 /1 2- /1 2- /1 2-11/1 2-1 /1 - /1 -1 /1 4- /1 4-1 /1 - /1 -1 /1 -1/2 -1/2

25 04 0 0 0 1 0 1 0 2 0 0 0 10 11 20 1 1 0 2 0 2 20 4 0

-1/2 -1/2 10 Caution

0

50 0 1 1 0 2 0 0 4 0 0 11 40 1 0 22 0 0

75 12 2 2 0 4 40

100 1 2 0 40 20 40 1 1 22 2 4 0

11 0 1 10 24 40 0 4 0 1 0 102 4 0 12 0 11 1 0 14 1 1 114 1 1 22 1 204 2 2 1 0 240 20 1 2

125 22 4 0 0 11 1 2 40

0 0 0 0

10 12 1 0 1 2 2 40 400 4

Horse Power at Various Revolutions per Minute 150 175 200 225 250 275 300 350 2 1 4 44 4 2 4 4 4 1 4 1 0 0 0 0 0 10 0 11 0 1 0 10 40 10 0 12 10 1 0 14 0 1 20 1 0 10 0 12 0 14 0 1 0 1 10 1 0 21 0 2 40 14 20 1 0 1 0 21 0 2 0 2 2 40 10 22 0 2 0 0 0 4 10 0 41 0 4 0 4 20 0 4 0 1 2 0 0 4 0 1 0 0 114 0 0 0 101 112 12 1 1 0 10 120 1 1 0 1 1 0 210 11 1 1 1 1 1 21 2 4 2 1 4 1 20 2 1 2 2 2 0 1 2 224 2 2 20 2 4 44 2 2 1 4 4 4 4 2 2 2 4 0 4 2 4 0 44 401 4 1 4 1 0 40 4 4 1 1 4 1 4 4 0 1 41 21 01 1 1 1122 0 4 4 41 4 102 1121 1 0

-B S

PT14-17

400 500 600 1 10 10 1 1 1 0 1 0 2 40 21 0 2 2 40 2 20 4 0 0 4 0 0 0 0 0 1 1 114 1 1 0 1 1 1 0 22 2 0 240 00 0 1 1 4 410 1 1 1 41 1 4 114 1 114 1 10 0 1 1 12 2 1 0 1 2 14 1 224

700 800 900 12 14 1 10 1 21 24 40 2 40 1 0 20 0 4 0 4 0 0 0 0 10 121 1 1 1 2 20 22 2 1 2 4 1 0 40 420 4 0 41 4 2 04 1 21 24 102 11 4 1104 12 2 141 1 40 1 1 1 2 1 0 1 20 1 0 21 1 24 2244 2 2 2 1 2 1

Engineering

Shaft Size

Conveyor Components

Table 23: Severe Conditions (Heavy shock loads. Excessively tight belts. long clutch sleeves.)


DYNA-SYNC

ENGINEERING/TECHNICAL Selection of Shaft Diameters (Cont’d) Shaft Stiffness, Shaft Deflection-Standard shafting of adequate strength usually has a sufficiently large diameter to prevent excessive deflection in ordinary installations. It is wise to select shafting of generous diameter, as the greater the diameter, the greater the stiffness. A high tensile strength alloy shaft, although stronger, is no stiffer than a standard shaft of the same diameter.

HT Synchrous Belts

While it is sometimes possible to use an alloy shaft of less diameter than a standard shaft of equal strength, this practice is usually inadvisable, as the deflection is increased. Shafts carrying medium or long clutch sleeves should be especially generous. High Speed Shafts-High speed sometimes causes shaft whipping or vibration. Making the shaft diameter generous and the distance between bearing centers short usually prevents this trouble.

Sprockets

Location of the bearings close to wheels and couplings is advisable whether the shaft is transmitting heavy or light loads.

dangerous concentration of stress will occur at the fillet. See heading-”Turning Down Shaft Ends.” (PT14-15). Shaft Keyseats-Plain keyseats are preferable to round end keyseats in respect to causing the least concentration of stress. However, round end keyseats are often used because of design and assembly requirements. Ends left by the milling cutter should not project into babbitted or bronze bushed bearing, but may project under the sleeve of any Dodge anti-friction bearings. Shaft diameters obtained from the tables or chart allow for the use of keyseats. Shaft Bearings-On ordinary line shafting, bearings are commonly spaced about eight feet centers. On large diameter shafts, the spacing may be somewhat greater. Wheels and clutches should be located near bearings to avoid dangerous bending, deflection and vibration. Bearings should be mounted on adequate supports so that accurate alignment may be maintained. Shafting misalignment may cause shaft or bearing failure. Shaft Couplings-Where a rigid coupling is used, it is preferable to have a bearing fairly close. Where a cutoff coupling or a flexible coupling is used, locate bearings close to each end of the coupling.

The use of high tensile strength alloy shafting instead of standard shafting is of no help in preventing vibration as this will not improve the stiffness and deflection characteristics of the shaft. Stepped Shafts- For a heavily loaded wheel, a shaft with a boss or enlarged section under the wheel and turned to a smaller diameter at the bearings often provides the most economical installation. The two different diameters should be joined by a very generous fillet, as otherwise a

Conveyor Components

Expansion of Shafting-Where changes in the length of the shaft due to changes in temperature are to be expected and the bearings are mounted on supporting structures other than steel, consideration must be given to expansion. For more detailed information see PT14-20, headed: “Expansion of Shafting.”

Factors for Shafting Other Than Standard Shafting When it is necessary to use other than standard shafting, multiply required diameter for standard shafting as found in the tables or chart by proper factor from Table 24 below. Standard keyseated shafting, using a safe shear stress of 6,000 PSI is the basis of shafting tables and chart. For safe shear stress of other materials, use 1/10 of nominal ultimate tensile strength. For example, use 8,000 for C1045 and 10,000 for 4140 keyseated shafting. When definite physical specifications are known the least of 13.5% of minimum ultimate tensile strength and 22.5% of minimum

elastic limit in tension may be used for keyseated shafting; 18% and 30% respectively if not keyseated. Caution-As the deflection of steel shafting depends upon the diameter and not upon the analysis of the steel, care should be exercised in the use of alloy shafting not to reduce the diameter unduly. Deflection should not be excessive and bearing capacities should be adequate. It is usually best to use standard shafting instead of a smaller diameter alloy shaft. The smaller alloy shaft may safely transmit the torque but often is undesirable in respect to deflection, vibration and bearing life.

Engineering

Table 24: Shear Stress Factors Safe Shear Stress 00 1 000 1 00 2 000 2 00

Factor 22 1 1 1 1 442 1

Safe Shear Stress 000 00 4 000 4 00 000

Factor 12 0 11 1 14 1 101 10

Safe Shear Stress 00 000 00 000 000 PT14-18

Factor 1 02 1 000 4 0 0

Safe Shear Stress 000 10 000 11 000 12 000 1 000

Factor 4 4 1 4

Safe Shear Stress 14 000 1 000 1 000 1 000 1 000

Factor 4 21 0


Example: Engine extension shaft driving single cylinder compressor, 15,000 pound-inches torsional moment, 14,000 pound- inches bending moment. Because of the heavy shock running load conditions use scales designated “Light or Heavy Starting and Severe Shock Running”. Project a line down from 15,000 torsional moment. Project a line to the right from 14,000 bending

moment. The two lines intersect between 3-7/16 and 3-15/ 16 curves. Use 3-15/16 standard shafting. Note: The above chart is based on ASME approved standard ASA-B17C-1927 withdrawn in 1954. If the latest shaft selection analysis is required refer to ANSI/ASME B106.1M-1985. Note: If considering use of other shafting material refer to “Selection of Shaft Diameters” on page PT14-18. PT14-19

Engineering

Conveyor Components

Sprockets

HT Synchrous Belts

Combined Torsion and Bending of Standard Shafts (Based on a Safe Shear Stress of 6,000 PS for Keyseated Shafting)

DYNA-SYNC

ENGINEERING/TECHNICAL


DYNA-SYNC

ENGINEERING/TECHNICAL Expansion of Shafting Provision should be made to permit the free movement of shafting endwise due to temperature changes. One bearing should serve as an anchor bearing to locate the shaft endwise. All other bearings should permit the shaft to move freely endwise.

HT Synchrous Belts

The anchor bearing is often located near an important wheel. On long shafts it should preferably be located near the center of the shaft to keep the expansion of the two ends to a minimum. If the anchor bearing is babbitted it should be fitted with collars. If it is an anti-friction bearing it should be of the non-expansion type, which is the designation of Dodge roller and ball bearings for use as anchor bearings. All bearings on the shafting other than the anchor bearing should permit the shaft to move freely endwise. If babbitted there should be no thrust collars. If anti-friction these bearings should be of the expansion type.

Sprockets

Several shafts firmly fastened together expand as if one continuous shaft. An example of this is line shafting with flange couplings. If the expansion is considered excessive a long line shaft may be split into two or more sections, the sections being connected with expansion couplings. Amount of Expansion to be provided forThe amount of shafting expansion is given in Table 25 below. For example, with a 1005 temperature rise on a 150 ft. line shaft with the anchor bearing located 70 ft. from one end and 80 ft. from the other end the ends will move.529� and.605� respectively away from the anchor bearing. The

structure supporting the bearings may also expand but usually not as rapidly and as much as does the shafting. Several cases follow: Case 1-Bearings supported on steel structures, where the shaft and structure are exposed to the same temperatures, will expand at the same rate. Expansion allowance is usually not required. If the shaft is exposed to a higher temperature than the support, allowances should be made. For example, if the shaft temperature is expected to change 80, and the temperature of the structure 60, the resulting movement between shafting and support ends will be equivalent to a 20 change. Case 2-For bearings supported on wood, brick, or concrete walls, or on piers with foundations in the ground, the amount of expansion is usually considered negligible. Therefore, the full amount of shafting expansion as calculated in Table 25 below, may be accommodated. Case 3-Certain structural designs have built-in flexibility. Where this is the case, expansion type bearings are not necessary. Case 4-Short shafts with only two bearings are usually designed without compensation for expansion, if temperature variations are not excessive. Advice on Expansion ProblemsDodge power transmission engineers will gladly make recommendations concerning shafting expansion problems and the use of suitable bearings.

Conveyor Components

Table 25: Linear Expansion of Steel Shafting

Engineering

Base on Expansion In Inches = 0.0000063 x 12 x Length in Feet x Temp. Increase in Degrees Fahrenheit Length Temperature Increase-Degrees F. Length Temperature Increase-Degrees F. 20 40 60 80 100 20 40 60 80 (Feet) (Feet) 1 001 00 0 004 00 0 00 40 0 0 121 1 1 242 2 00 0 00 0 00 1 0121 01 1 4 0 1 204 2 2 004 00 1 01 01 1 022 0 0 1 1 22 02 4 00 0 0121 01 1 0242 0 02 0 1 24 00 01 1 022 0 02 0 0 0 1 1 1 2 2 00 1 01 1 02 2 0 04 4 0 1 2 010 0212 0 1 042 0 2 0 10 212 1 42 0121 0242 0 04 4 0 0 11 22 40 4 4 01 02 2 040 0 44 0 0 0 121 242 4 4 10 01 1 0 02 04 4 0 0 0 12 2 14 12 01 1 0 0 44 0 2 0 0 0 1 2 2 40 44 14 0212 042 0 0 4 10 144 2 4 1 1 024 04 0 0 121 100 1 1 02 4 4 0 1 02 0 4 0 2 10 1 110 1 4 20 0 0 0 0 0 1 121 1 1 120 1 1 44 2 2 0 0 11 1 1 1 1 0 1 0 0 04 0 1 1 1 1 22 140 212 42 4 0 10 1 212 2 1 0 22 4 4 0 0 PT14-20

100 02 40 41 4 4 4 1 2 0 4 0 1 2 0 10 11 4


Weights and Properties of Steel Shafting Table 26: Weight of Round Steel Shafting Shaft Size /4 / 1 /1 1 1-1/ 1- /1 1-1/4 1- / 1- /1 1-1/2 1-11/1 1-1 /1 2 2- /1 2- /1 2-1/2 2-11/1 2-1 /1 - /1 -1 /1 4- /1 4-1 / - /1

1 1 20 2 2 4

2 0 40 4

42 0 0 10 0 10 12 1 1 1 2 0 1 41 4 2 1 0

10 1 11 12 1 20 21 2 2 4

3 4 1 0 0 10 0 11 12 1 1 1 2 0 2

5 10 2 11 1 1 1 20 2 2 0

6 0 12 2 14 1 1 0 20 1 22 2 0 0 4

0

0 4

4

4 0

4 10 1 0 1 1 2

4 0 1 4 10 1 4 1 1 1 20 2 22 24 0 40 4 1

124 1 1 2 2

2 12 1 210 2 0 1 4

11 1 20 2 2 4 1

100 11 1 1 24 1 1 4 4

Weight of Shafting for Various Lengths in feet 7 8 9 10 12 10 12 0 1 1 1 14 1 1 4 20 2 1 1 21 2 2 2 1 21 24 0 2 2 2 4 2 01 4 41 2 4 01 40 4 2 2 42 0 4 40 4 4 4 0 0 44 0 42 4 4 0 2 1 1 0 0 0 100 120 10 12 0 102 11 12 1 111 12 14 1 1 0 11 1 4 1 0 1 200 1 1 4 1 4 1 2 2 1 1 1 4 20 2 1 2 221 2 2 4 1 2 0 1 414 4 421 4 2 1 4 21 1 1 2 11 0 4 1 11 4

14 21 2

16 24

18 2

4

42 4 1

4

4 0

1 4 10 140 1 0 1 222 2 4 2 0 2 442 0 11 110 1 4

1

1

122 1 1 1 1 20 2 4 2 0

10 1 1 1 1 2 2 0 2 01 4 41

0 2 41 1041 12 1

20 0 41 4

22

24

4

4 2 4 1 0 100 121 1 144 1 241 2 0 1 401 4

4 101 110 120 1 2 201 214 2 1 4 4 1 1 2 10 2 1 02 1 1 2

4 4 11 2 1421 1 0

2 111 121 1 2 1 221 2 2 1 4 42 0 11 11 14 2 1 211

4 12 2 1 2 1 4 2 0

Weight Per Inc. 12 1 0 1 22 2 1 14 4 420 4 0 00 4 0 10 1 2 1 1 1 1 2 2 4 4 42

HT Synchrous Belts

DYNA-SYNC

ENGINEERING/TECHNICAL

01

S

Table 27: Weight and Properties of Round Steel Shafting Shaft Size 1/1 1/ /1 1/4 /1 / /1 1/2 /1 / 11/1 /4 1 /1 / 1 /1 1 1-1/1 1-1/ 1- /1 1-1/4 1- /1 1- / 1- /1 1-1/2 1- /1 1- / 1-11/1 1- /4 1-1 /1 1- / 1-1 /1 2 2-1/1 2-1/ 2- /1 2-1/4 2- /1 2- /

Weight per Inch 000 00 00 01 021 0 1 042 0 0 0 0 10 1 12 14 1 01 1 4 22 2 2 1 42 4 0 4

4 1 00 10 11 11 12

Section Modulus Bending Torsion 000024 00004 0001 2 000 000 4 0012 4 001 4 00 0 002 00 2 00 1 010 4 00 221 01 442 012 024 01 0 4 0240 04 0 1 0 0414 0 2 0 2 10 0 1 1 0 0 1 1 0 2 1 11 2 1 2 1 44 2 1 1 2220 44 2 2 104 2 1 2 1 2 4 4 0 421 42 4 1 4 2 2 10 2 4 11 4 1 12 4 140 1 42 4 1 1 14 1 2 421 1 4 1 02 20 1 11 22 1 214 2 42 1 1 2 0

Moment of Inertia Bending Torsion 000001 000002 000012 000024 0000 1 000121 0001 2 000 0004 000 000 1 001 41 001 00 00 1 00 1 004 00 00 01 0 0110 021 01 0 11 0214 042 02 0 0 0 04 1 0 2 0 2 12 1 0 1 0 1 2 11 2 14 2 1 1 0 20 41 2 24 4 0 2 2 2 42 4 1 1 4 04 20 2 10 0 0 1 21 1 1 4 4 1 1 1 1 001 2 002 1 124 2 24 12 2 1 1 404 2 0 1 2 124

Shaft Size 2- /1 2-1/2 2- /1 2- / 2-11/1 2- /4 2-1 /1 2- / 2-1 /1 -1/1 -1/ - /1 -1/4 - /1 - / - /1 -1/2 - /1 - / -11/1 - /4 -1 /1 - / -1 /1 4 4-1/1 4-1/ 4- /1 4-1/4 4- /1 4- / 4- /1 4-1/2 4- /1 4- / 4-11/1 4- /4

PT14-21

Weight per Inch 1 2 1 14 1 1 1 1 1 1 4 1 2 2 00 20 21 22 2 2 44 2 2 2 2 2 2 2 2 02 1 2 4 4

Section Modulus Bending Torsion 1 422 2 44 1 4 0 1 2 04 1 2 1 0 11 2 042 40 4 21 4 4 2 4 24 4 2 1 01 2 20 40 2 2 1 0 40 1 4 4 4 20 44 4 4 2 1 440 12 2

0 4 01 41 42 4 4 0 4 4 4 01

2 1 20 4 221 4 24 1 10 11 10 2

41 4 10 10 11 42 11 12 1 1 1 14 42 1 0 1 1 44 1 1 1 1 1 4 20 22 21 04

Moment of Inertia Bending Torsion 1 4 1 1 2 11 42 2 1 4 1 2 1 122 2 0 1 0 1 14 4 0 10 2 4 1 4 1 0 10 1 4 10 10 11 2 12 4 4 1 1 14 0 1 1 4 1 0 1 1 0 1 41 10 20 4 11 0 22 14 11 0 2 0 12 2 1 1 2 4 14 21 2 42 1 0 01 1 01 20 1 1 1 0 0 20 1 40 2 21 2 42 4 22 4 44 2 2 0 4 40 24 4

Conveyor Components

U

Engineering

-1 /1

Sprockets

* Recommended Diameters T


DYNA-SYNC

ENGINEERING/TECHNICAL Table 27: Weight and Properties of Round Steel Shafting Shaft Size 4-1 /1 4- / 4-1 /1

HT Synchrous Belts

-1/1 -1/ - /1 -1/4 - /1 - / - /1 -1/2 - /1 - / -11/1 - /4 -1 /1 - / -1 /1

Sprockets

-1/1 -1/ - /1 -1/4 - /1 - / - /1 -1/2 - / - /4 - / -1/ -1/4 - / -1/2 - / - /4 - /

Conveyor Components

-1/ -1/4 - / -1/2 - / - /4 - /

Engineering

-1/ -1/4 - / -1/2 - / - /4 - / 10 10-1/4 10-1/2 10- /4 11 11-1/4 11-1/2 11- /4 12 12-1/4 12-1/2 12- /4 1 1 -1/4

Weight per Inch 1 2 42 0 4 1 2 42 2 0 1 1 4 00 1 4 1 0 21 10 10 10 0 10 0 11 0 11 0 12 10 12 0 12 0 1 0 1 0 14 0 14 0 1 10 1 0 1 10 1 0 1 00 1 0 1 00 1 0 1 00 1 0 20 10 20 0 21 10 21 0 22 20 2 40 24 0 2 0 2 0 2 10 2 40 0 0 2 00 40 4 0 10 0 00

Section Modulus Bending Torsion 10 4 21 11 22 11 2 2 12 2 24 4 12 4 2 4 1 22 2 4 1 0 2 41 14 21 2 41 14 2 2 44 1 2 04 1 1 1 2 1 0 1 4 4 1 0 12 1 1 2 1 1 2 20 41 10 21 21 42 41 21 4 22 4 12 2 2 4 1 2 4 4 24 4 2 44 0 2 1 2 2 2 2 0 01 0 1 0 0 1 41

1 02 4 2

41 42 4 2 4 0 4 02 2 1

2 4 0 1 40

02 2 1 4 0 0 41 4 0 4 4 1 10 2 11 121 1 0 1 14 1 1 2 1 1 04 1 1 20 4 21 22

100 0 10 0 110 0 11 0 120 0 12 00 1 1 0 1 0 14 10 14 20 1 40 1 1 0 1 0 1 10 1 2 00 1 10 1 0 211 40 22 0 24 0 2 1 0 2 0 2 0 1 0 0 0 0 0 40 00 4 1 40 4 0

Moment of Inertia Bending Torsion 2 2 2 2 4 2 1 0 1 2 24 44 2 10 40 42 1 44 2 4 4 14 1 0 4 1 01 2 1 0 1 4 0 4 10 4 0 2 4 101 0 10 0 11 0 12 0 1 0 14 20 1 0 1 0 1 10 1 0 201 10 21 0 22 40 241 0 2 20 2 1 0 2 0 04 0 22 10 40 0 40 20 0 421 0 44 0 4 0 4 0 0 41 0 0 0 1 0 0 0 0 101 110 11 12 1402 1 1

10 4 20 1 4 2 4 2 102 0 10 0 112 10 11 00 122 00 12 20 1 2 0 1 20 14 0 14 0 1 0 1 2 20 1 0 1 20 1 10 20 0 21 0 2 0 2 00 2 1 20 2 0 40 10 0 1 0 4 20 0 402 10 42 0 4 4 0 4 00 12 0 4 0 0 0 10 44 10 0 0 1 0 40 0 42 0 20 0 1 0 10 4 11 1 11 14 1 1 1 1 1 20 2211 2 2 4 2 04 02

Shaft Size 1 -1/2 1 - /4 14 14-1/4 14-1/2 14- /4 1 1 -1/4 1 -1/2 1 - /4 1 1 -1/4 1 -1/2 1 - /4 1 1 -1/4 1 -1/2 1 - /4 1 1 -1/4 1 -1/2 1 - /4 1 1 -1/4 1 -1/2 1 - /4 20 20-1/4 20-1/2 20- /4 21 21-1/4 21-1/2 21- /4 22 22-1/4 22-1/2 22- /4 2 2 -1/4 2 -1/2 2 - /4 24 24-1/4 24-1/2 24-1/4 2 2 -1/4 2 -1/2 2 - /4 2 2 -1/4 2 -1/2 2 - /4 2 2 -1/2 2 2 -1/2 2 2 -1/2 0 0-1/2 1 1-1/2 2 2-1/2 4

PT14-22

Weight per Inch 40 0 42 00 4 0 4 10 4 0 4 40 0 00 1 0 40 10 0 0 0 0 2 40 4 20 10 10 0 00 2 00 4 00 10 10 0 20 2 40 4 0 0 0 1 10 40 0 00 100 40 102 0 10 10 10 0 110 00 112 0 11 00 11 0 120 10 122 0 12 40 12 00 1 0 0 1 40 1 20 1 0 141 0 144 0 14 40 1 0 0 1 20 1 10 1 00 1 2 00 1 10 1 4 0 1 0 0 1 0 1 40 200 00 20 0 21 0 220 0 22 0 2 4 0 242 10 2 0 2 2 0

Section Modulus Bending Torsion 241 0 4 10 2 20 10 40 2 40 0 2 4 10 20 2 0 0 1 00 0 10 1 0 2 0 4 20 40 0 1 20 0 10 402 10 04 20 421 0 42 0 441 00 2 00 4 1 40 22 0 4 2 0 4 0 0 0 100 2 20 10 2 4 10 10 2 0 114 0 11 21 0 124 4 10 12 4 40 1 4 00 0 1401 2 00 14 0 1 1 40 1 1 1 20 1 0 4 0 1 2 10 1 4 0 20 1 1 42 10 1 4 0 1 1 1010 2020 104 20 1 10 1 21 111 22 11 2 12 11 4 2 12 4 24 12 4 2 4 1 1 2 0 1 2 14 1400 2 00 1444 2 14 2 1 4 0 1 0 1 1 1 2 2 1 2 1 2 4 1 1 2 1 2 4 1 1 2 2042 40 21 4 10 22 4 4 2 4 4 2 20 041 2 1 01 2 1 2 2 4 0 1 21 4 4 0 40 2 0 1 420 41

Moment of Inertia Bending Torsion 1 0 2 1 1 0 1 1 2024 404 21 0 4 40 2 24 4 4 24 4 0 2 10 2 021 041 21 4 4 422 4 2 4 2 4100 200 4 4 4 04 20 4 4 1 10 0 44 10 1 0 11 00 0 121 4 12 4 41 1 4 1 0 141 4 14 4 1 0 2 4 1 0 1 100 1 200 4 1 0 1000 2001 104 20 10 21 0 114 22 120 1 240 1 12 1 2 1 1 1 14 2 2 1 2 4 14 44 2 14 1 2 41 1 1 12 1 2 2 2 1 1 1 2 1 41 1 1 0 1 4 0 20 41 11 21 1 4 1 224 2 44 4 2 0 4 14 2420 4 41 2 1 4 02 2 0 21 4 2 0 4 14 01 2 0 44 2 4 1 4 1 4 1 4 1 1 22 424 4 4 0 4 2 14 2 102 44 4 10 0 214 11 42 1 11 4 2 14 24


Conveyor Components

Sprockets

HT Synchrous Belts

Viscosity Classification Equivalents

DYNA-SYNC

ENGINEERING/TECHNICAL

Rule-of-Thumb: The comparable ISO grade of a competitive product whose viscosity in SUS at 1005F is known can be determined by using the following conversion formula:

PT14-23

SUS @ 100F รท 5 = cSt @ 40C

Engineering

ISO VISCOSITY CLASSIFICATION SYSTEM All industrial oils are graded according to the ISO Viscosity Classification System, approved by the International Standards Organizations (ISO). Each ISO viscosity grade number corresponds to the mid-point of viscosity range expressed in centistokes (cSt) at 40C. For example, a lubricant with an ISO grade of 32 has a viscosity within the range of 28.80-35.2, the midpoint of which is 32.


DYNA-SYNC

ENGINEERING/TECHNICAL English Standard Measures Long Measure

Temperature The following equation will be found convenient for transforming temperature from one system to another: Let F = degrees Fahrenheit; C = degrees Centigrade; R = degrees Reamur. F-32 = C = R 180 100 80

1 mile = 1760 yards = 5280 feet. 1 yard = 3 feet = 36 inches. 1 foot = 12 inches.

Surveyor’s Measure

HT Synchrous Belts

1 mile = 8 furlongs = 80 chains. 1 furlong = 10 chains = 220 yards. 1 chain = 4 rods = 22 yards = 66 feet = 100 links. 1 link = 7.92 inches.

Avoirdupois or Commercial Weight

Square Measure 1 square mile = 640 acres = 6400 square chains. 1 acre = 10 square chains = 4840 square yards = 43,560 square feet. 1 square chain = 16 square rods = 484 square yards = 4356 square feet. 1 square rod = 30.25 square yards = 272.25 square feet = 625 square links. 1 square yard = 9 square feet. 1 square foot = 144 square inches. An acre is equal to a square, the side of which is 208.7 feet.

Dry Measure Sprockets

1 bushel (U.S. or Winchester struck bushel) = 1.2445 cubic foot = 2150.42 cubic inches. 1 bushel = 4 pecks = 32 quarts = 64 pints. 1 peck = 8 quarts = 16 pints. 1 quart = 2 pints. 1 heaped bushel = 1 1/4 struck bushel. 1 cubic foot = 0.8036 struck bushel. 1 British Imperial bushel=8 Imperial gallons=1.2837 cubic foot = 2218.19 cubic inches.

Liquid Measure

Conveyor Components

1 U.S. gallon = 0.1337 cubic foot = 231 cubic inches = 4 quarts = 8 pints. 1 quart = 2 pints = 8 gills. 1 pint = 4 gills. 1 British Imperial gallon=1.2003 U.S. gallon=277.27 cubic inches. 1 cubic foot = 7.48 U.S. gallons.

Circular and Angular Measure 60 seconds (“) 60 minutes 360 degrees 57.3 degrees 2 π radians

= = = = =

1 minute ( ‘) 1 degree (  ) 1 circumference (C) 1 radian 1 circumference (C)

1 gross or long ton = 2240 pounds. 1 net or short ton = 2000 pounds. 1 pound = 16 ounces = 7000 grains. 1 ounce = 16 drams = 437.5 grains.

Measures of Pressure 1 pound per square inch = 144 pounds per square foot = 0.068 atmosphere = 2.042 inches of mercury at 62 degrees F. = 27.7 inches of water at 62 degrees F. = 2.31 feet of water at 62 degrees F. 1 atmosphere = 30 inches of mercury at 62 degrees F. = 14.7 pounds per square inch = 2116.3 pounds per square foot = 33.95 feet of water at 62 degrees F. 1 foot of water at 62 degrees F. = 62.355 pounds per square foot = 0.433 pound per square inch. 1 inch of mercury at 62 degrees F. = 1.132 foot of water = 13.58 inches of water = 0.491 pound per square inch. Column of water 12 in. high, 1 in. dia. = .341 lbs.

Cubic Measure 1 cubic yard = 27 cubic feet. 1 cubic foot = 1728 cubic inches. The following measures are also used for wood and masonry: 1 cord of wood = 4 X 4 X 8 feet = 128 cubic feet. 1 perch of masonry = 16-1/2 X 1-1/2 X 1 foot = 24-3/4 cubic feet.

Shipping Measure For measuring entire internal capacity of a vessel: 1 register ton = 100 cubic feet. For measurement of cargo: 1 U.S. shipping ton = 40 cubic feet = 32.143 U.S. bushels = 31.16 Imperial bushels. British shipping ton = 42 cubic feet = 33.75 U.S. bushels = 32.72 Imperial bushels.

Troy Weight, Used for Weighing Gold and Silver

Specific Gravity

Engineering

The specific gravity of a substance is its weight as compared with the weight of an equal bulk of pure water. For making specific gravity determinations the temperature of the water is usually taken at 62 F. when 1 cubic foot of water weighs 62.355 lbs. Water is at its greatest density at 39.20 F. or 4 Centigrade.

1 pound = 12 ounces = 5760 grains. 1 ounce = 20 pennyweights = 480 grains. 1 pennyweight = 24 grains. 1 carat (used in weighing diamonds) = 3.086 grains. 1 grain Troy = 1 grain avoirdupois = 1 grain apothecaries’ weight.

Measure Used for Diameters and Areas of Electric Wires 1 circular inch = area of circle 1 inch in diameter = 0.7854 square inch. 1 circular inch = 1,000,000 circular mils. 1 square inch = 1.2732 circular inch = 1,273,239 circular mils. A circular mil is the area of a circle 0.001 inch in diameter.

Board Measure One foot board measure is a piece of wood 12 inches square by 1 inch thick, or 144 cubic inches. 1 cubic foot therefore equals 12 feet board measure.

PT14-24


Inches Fractions 1/ 4 1/ 2 / 4 1/1 / 4 / 2 / 4 1/ / 4 / 2 11/ 4 /1 1 / 4 / 2 1 / 4 1/41 / 4 / 2 1 / 4 /1 21/ 4

Decimals 01 2 0 12 04 0 2 0 12 0 10 12 140 2 1 2 1 1 1 20 12 21 2 4 2 0 2 2 2 12 2 12 2 12

Milli- meters 4 11 1 1 1 4 2 1 2 1 2

2 / 2 / 2 / 2 / 1/

4 4

/ 1 / 0 4 144 41

/ / 41/

4 4 /

Inches Fractions 11/ 2 4 / 4 1 / 2 4 /1 4 1 / 2 4 1/2 4 1 / 2 4 /1 4 1 / 2 4 / 4 21/ 2 4

Decimals 4 0 2 40 2 4 21 4 4 12 4 4 00 1 2 12 4 2 12 0 2 0 2 2 1

Milli-meters 1 12 2 22 10 1 10 1 11 11 11 0 11 0 12 0 12 00 1 0 1 4 4 1 1 14 2 14 4 14 0 1 1 4 1 1 2 2 1 1 0

4 / 4 / 4 / 1/ / / / / 1/ /

Inches Fractions 11/1 4 2 / 2 4 /4 4 2 / 2 4 1 /1 4 2 / 2 4 / 4 2 / 2 4 1 /1 4 1/ 2 4 1

Decimals

Milli-meters

4 1 000

1 4 1 1 2 1 1 0 0 1 44 1 44 20 241 20 21 0 4 21 4 1 21 2 22 22 22 22 2 01 2 41 2 1 24 20 24 0 2 00 2 400

Milli-meter

Decimal

0 12 1 4 0 2 12 12 2 12 4 0 2 0 24 21 12

DYNA-SYNC

Table 28: Decimal and Millimeter Equivalents of Fractions

HT Synchrous Belts

ENGINEERING/TECHNICAL

Milli-meter

Decimal

Milli-meter

Decimal

Milli-meter

0 0 4 11 11 1 4 1 2 22 2 14 4 0 4 0 4 244 11 1 11 0 2 2 2 0 4 0 40 2 14 0 1 44 42 1 02 2 10 2 1 102 1 141 1 1 110 1 2204 12 4 1 2 21 1 1 1 41 2 14 14 0 1 4 1 4 0 1 141 1 4 1 2 1 1 22 1 1 1 1102 1 0 1 1 2 1 1 0 2 00

2

2 04 24 20 1 2 12 21 2 204 2 2 2440 22 4 2 22 2 220 2 401 2 440 4 24 0 1 2 1 2 0 2 42 2 2 1 2 1 2 0 2 2 2 4 4 2 401 2 1 2 2 2 212 0 14 0 0 1102 14 0 1 22 4 2 1 0 0 4 4 2 42 1 4 4 0 4 0 2 2204 141 00 401 2 1 2

10 104 10 10 10 10 10 110 111 112 11 114 11 11 11 11 11 120 121 122 12 124 12 12 12 12 12 1 0 1 1 1 2 1 1 4 1 1 1 1 1 140 141 142 14 144 14 14 14 14 14 1 0 1 1 1 2 1

4 0 11 4 0 44 41 4 1 22 4 212 42 1 42 1 4 0 0 4 00 4 40 44 4 44 1 44 1 4 2 4 2 4 0 2 4 4 4 0 4 2440 4 4 0 1 4 42 2 4 1 4 212 4 0 00000 0 0 11 11 1 4 1 2 22 2 14 4 0 4 0 4 244 11 1 11 0 2 2 2 0 4 4 40 2 14 0 1 44 42 02 2

1 4 1 1 1 1 1 1 0 1 1 1 2 1 1 4 1 1 1 1 1 1 0 1 1 1 2 1 1 4 1 1 1 1 1 1 0 1 1 1 2 1 1 4 1 1 1 1 1 1 0 1 1 1 2 1 1 4 1 1 1 1 1 200 201 202 20 204

4

10 11 12 1 14 1 1 1 1 1 20 21 22 2 24 2 2 2 2 2 0 1 2 4

40 41 42 4 44 4 4 4 4 4 0 1

4

0 1 2 4

0 1 2 4

0 1 2 4

0 1 2 4

100 101 102

10 4 01 4

PT14-25

Decimal 0 2 102 141 1 110 2204 2 4 2 21 41 2 4 4 0 4 4 0 141 4 2 1 22 1 1102 0 2 1 0 00 04 24 0 1 12 1 204 2 2440 2 4 22 220 401 440 4 4 0 1 1 0 42 1 1 0 2 4 4 401 1 2 221 0 14

20 20 20 20 20 210 211 212 21 214 21 21 21 21 21 220 221 222 22 224 22 22 22 22 22 2 0 2 1 2 2 2 2 4 2 2 2 2 2 240 241 242 24 244 24 24 24 24 24 2 0 2 1 2 2 2 2 4 -

0 0 1102 14 0 1 22 4 2 1 0 0 4 4 2 42 1 4 4 0 4 0 2 2204 141 00 401 2 1 2 00 01 4 0 11 0 44 1 1 22 212 2 1 2 1 0 0 00 40 44 44 1 4 1 2 2 0 2 4 0 2440 0 1 42 2 1 212 0 10 00000 -

Conveyor Components

Decimal

1 2

Engineering

Milli-meter

Sprockets

Table 29: Millimeter-Inch Equivalents: 1� = 25.4mm (.03937� = 1mm)


DYNA-SYNC

ENGINEERING/TECHNICAL Metric System of Measurements Measures of Length 10 10 10 1000

Square Measure

1 1 1 1

100 100 100

2

2 2

1 1 1

2

Cubic Measure Measure of Weight

HT Synchrous Belts

10 10 10 10 10 10 1000

1 1 1 1 1 1 1

Dry and Liquid Measure H

10 10 10 100

T

Surveyor’s Square Measure 2

100 100 100

1 1 1

1 1 1

1000 1000 1000

1 1 1 1

1

1

1 2

F

2

Length Conversion Constants for Metric and U.S. Units 0

0

I I F

0 2 0 10 1 2 0 21

F S N

S N

2 4001 02 4 04 0 1440 000 04 1 0 1 2

Sprockets

Weight Conversion Constants for Metric and U.S. Units G G G G

1 1 4 2 0 2 0 1 2 2 204 2 T 1000 T 1000

G O F O O P N T G T

A A A 1 102 1 N T 421 G T

2000 2240

00101 0 4 A 2 2 A 02 A 4 2000 2240 I

0 1 1 01 0

T T

Area Conversion Constants for Metric and U.S. Units

Conveyor Components

S S S S H S S

001 1

S S S S A A S

10 11 2 4 104 24 104 1

I I F

4 1 4 1 0 2 1

404 00404 2

Volume Conversion Constants for Metric and U.S. Units C C C L L L L H H H H C C C

0 1 0 102 2 1 1 02 10 2 41 0 1 2 41 1 2 4 1 0 2 41 1 1 0

F C F C

O I

2 1

I

01 4

G C G C B C G C C

21 0 42

4 F

2

1 4 F 2 1 21 0 42 4 00 4 F 02 1 4 0

2

Engineering

Power and Heat Conversion Constants for Metric and U.S. Units C N C

0 00 H C R

B TU 1 H

1 4 H 41 B T U 1 2 22 2

B TU 2 2 P -F 1 P 112 N H 1 014 C H 4 B T U 0002 2 2 F - 2 F - 2 444

-

F F

PT14-26

-

C R

1000 1000

HI -


COMMON CONVERSION FACTORS USEFUL IN MECHANICAL POWER TRANSMISSION

DYNA-SYNC

ENGINEERING/TECHNICAL

Symbols and Abbreviations Used in Conversion Factors

Symbol G

Common prefixes and symbols used in the metric system are listed below. An example of use is 1000 meters is equivalent to 1 kilometer, and 1/1000 of one meter is equivalent to 1 millimeter.

Multiplication Factor-Decimal and Power of 10 1 000 000 000 1 000 000 1 000 100

μ

10

10

10 102

10

101

01

10-1

0 01

10-2

0 001

10-

0 000 001

Sprockets

Prefix

Prefixes Used in the Metric System

HT Synchrous Belts

This Handbook has retained use of familiar abbreviations consistent with existing product and trade literature rather than the abbreviations found in current publications of technical and scientific societies.

Symbols and abbreviations found in this section are those currently used in many texts and product publications. Considerable effort is underway to standardize on abbreviations for metric and English units of measurement. Recently, ASTM (American Society for Testing and Materials) and IEEE (Institute of Electrical and Electronic Engineers) published a standard practice on the metric system. † This publication consolidates a great deal of the current thinking and provides a system of abbreviations and symbols that differ somewhat from those used here.

10-

0 000 000 001

10-

Conveyor Components

N N T T

†ASTM/IEEE Standard Metric Practice, ASTM E 380-75, IEEE Std. 268-1976.

Engineering

“Reprinted with Permission of the Power Transmission Distributors Association”

PT14-27


DYNA-SYNC

ENGINEERING/TECHNICAL Symbol or Abbreviation

Symbol or Abbreviation

Term

Term

I C

C

-

C

2

HT Synchrous Belts

G N F

F

N -

-

P -I

P

-

Sprockets

2 R

Conveyor Components

-

R

-

Rounding of Numbers A 1 12

A 1

Engineering

11

0

11 4

0 12

44 14 0 04 1 00 2

PT14-28

-

-

F


centimeters per second (cm per sec) . . . . . . . . . . . feet per second (fps or ft per sec) . . . . . . . . . . . . . . . . . . . . . feet per second (fps) . . . . . . . . . . . . . . . . . . . . . . . . centimeters per second (cm per sec). . . . . . . . . . . . . . . . . . . meters per second (m per sec) . . . . . . . . . . . . . . . . . . . . . . . kilometers per hour (km per hr) . . . . . . . . . . . . . . . . . . . . . . . miles per hour (mph) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . kilometers per hour (km per hr). . . . . . . . . . . . . . . . knots (kn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . feet per second (fps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . kilometers per hour (km per hr) . . . . . . . . . . . . . . . . . . . . . . . feet per minute (ft per min.) . . . . . . . . . . . . . . . . . . . . . . . . . . knots (kn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . miles per hour (mph) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . kilometers per hour (km per hr) . . . . . . . . . . . . . . . . . . . . . . . radians per second (rad per sec) . . . . . . . . . . . . . . revolutions per minute (rpm) . . . . . . . . . . . . . . . . . . . . . . . . . degrees per minute (deg per min.). . . . . . . . . . . . . . . . . . . . . revolutions per minute (rpm) . . . . . . . . . . . . . . . . . . radians per second (rad per sec) . . . . . . . . . . . . . . . . . . . . . . degrees per minute (deg per min.). . . . . . . . . . . . . . . . . . . . .

0.3281 30.48 0.3048 1.097 0.6818 0.5396 1.467 1.609 88 1.152 1.853 9.55 3437.7 0.1047 360

DYNA-SYNC

VELOCITY

HT Synchrous Belts

ENGINEERING/TECHNICAL

ACCELERATION

To...

Multiply Col. A by

feet per second per second (ft per sec 2) m per sec2 revolutions per minute per second (rpm per sec) rad per sec2

meters per second per second (m per sec2) . . . . . . . . . . . . . ft per sec2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . radians per second per second (rad per sec2) . . . . . . . . . . . rpm per sec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

0.3048 3.281 0.1047 9.55

Engineering

Conveyor Components

To Convert From...

Sprockets

COLUMN A

PT14-29


DYNA-SYNC

ENGINEERING/TECHNICAL VOLUMETRIC FLOW RATES

HT Synchrous Belts

gallons per minute, US (gpm) . . . . . . . . . . . . . . . . .liters per second (l per sec) . . . . . . . . . . . . . . . . . . . . . . . . . . cubic feet per minute (cfm). . . . . . . . . . . . . . . . . . . . . . . . . . . cubic feet per hour (cu ft per hr) . . . . . . . . . . . . . . . . . . . . . . . gallons per minute, UK or Canadian (gpm) . . . . . .liters per second (l per sec) . . . . . . . . . . . . . . . . . . . . . . . . . . cubic feet per minute (cfm). . . . . . . . . . . . . . . . . . . . . . . . . . . cubic feet per hour (cu ft per hr) . . . . . . . . . . . . . . . . . . . . . . . cubic feet per second (cfs) gpm (UK or Canadian) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . gpm (US) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . liters per second (l per sec) . . . . . . . . . . . . . . . . . . . . . . . . . . liters per second (l per sec) cubic feet per minute (cfm). . . . . . . . . . . . . . . . . . . . . . . . . . . gpm (UK or Canadian) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . gpm (US) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . millions of gallons per day, US (MGD) liters per second (l per sec) . . . . . . . . . . . . . . . . . . . . . . . . . . cubic feet per minute (cfm). . . . . . . . . . . . . . . . . . . . . . . . . . . gallons per minute, US (gpm). . . . . . . . . . . . . . . . . . . . . . . . .

0.008434 0.1337 8.022 0.0101 0.1606 9.634 373.77 448.86 1699.2 2.119 13.20 15.85 43.81 92.85 694.44

PRESSURE

Sprockets Conveyor Components

pascals (Pa) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .pounds per square inch (psi) . . . . . . . . . . . . . . . . . . . . . . . . . pounds per square foot (lb per ft2) . . . . . . . . . . . . . . . . . . . . . newtons per square meter . . . . . . . . . . . . . . . . . . . . . . . . . . . pounds per square inch (psi). . . . . . . . . . . . . . . . . .atmospheres, std. (atm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pounds per square foot (lb per ft2) . . . . . . . . . . . . . . . . . . . . . pascals (Pa) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . foot of water (ft of H20) 60F . . . . . . . . . . . . . . . . . . . . . . . . . . atmospheres (atm), standard . . . . . . . . . . . . . . . . .psi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lb per ft2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . inch of water, 60F (in of H20) . . . . . . . . . . . . . . . . .psi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lb per ft2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . foot of water, 60F (ft of H20) . . . . . . . . . . . . . . . . . .psi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lb per ft2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

0.0001450 0.02089 1 0.0680 144 6894.8 2.301 14.70 2116.8 101325 0.03609 5.197 248.84 0.4331 62.36 2985.9

WEIGHT, MASS, INERTIA pounds (Ib)*. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .kilograms (kg). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ounces (oz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . kilograms (kg) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .pounds (lb) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ounces (oz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Engineering

PT14-30

0.4536 16 2.205 35.27


COLUMN A Multiply To Convert From... To Col. Aby tons (short) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . metric tons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.9072 kilograms (kg). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 907.2 pounds (lb) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000 metric tons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . tons (short). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.102 kilograms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000 pounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2205 pounds, weight (lb) . . . . . . . . . . . . . . . . . . . . . . . . . slugs, mass (lb-sec2 per ft) . . . . . . . . . . . . . . . . . . . . . . . . . . 0.03106 pound-foot2 (lb-ft2) . . . . . . . . . . . . . . . . . . . . . . . . . kilogram-meters2 (kg-m2). . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.04214 *pounds and ounces are avoirdupois

FORCE AND TORQUE pounds (lb) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . newtons(N). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . newtons (N). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pounds (lb) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . newton-meters (N-m) . . . . . . . . . . . . . . . . . . . . . . . pound-feet (lb-ft). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pound-inches (lb-in) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ounce-inches (oz-in) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ounce-inches (oz-in) . . . . . . . . . . . . . . . . . . . . . . . . Ib-ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N-m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lb-in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pound-inches (lb-in) . . . . . . . . . . . . . . . . . . . . . . . . Ib-ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N-m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . oz-In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pound-feet (lb-ft) . . . . . . . . . . . . . . . . . . . . . . . . . . . N-m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lb -in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . oz-In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.448 0.2248 0.7376 8.851 141.60 0.005208 0.007062 0.0625 0.0833 0.1298 16 1.356 12 192

Sprockets

WEIGHT, MASS, INERTIA, continued

HT Synchrous Belts

DYNA-SYNC

ENGINEERING/TECHNICAL

degrees Fahrenheit (F) . . . . . . . . . . . . . . . . . . . . . . degrees Celsius (C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . degrees Celsius (C) . . . . . . . . . . . . . . . . . . . . . . . . degrees Fahrenheit (F) . . . . . . . . . . . . . . . . . . . . . . . . . degrees Fahrenheit (F) . . . . . . . . . . . . . . . . . . . . . . degrees Rankine (R) . . . . . . . . . . . . . . . . . . . . . . . . . . . degrees Celsius (C) . . . . . . . . . . . . . . . . . . . . . . . . degrees Kelvin (K) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Examples:

1. Convert 12F to C. C = 5/9 (F-32) = 5/9 (12-32) = 5/9 (-20) Answer = -11.1C 2. Convert 40C to F. F = 9/5C + 32 = 9/5 (40) + 32 = 72 + 32 Answer = 104F

PT14-31

C =5/9 (F-32) F=9/5C+32 R =F+459.69 K=C+273.16

Engineering

horsepower (hp) . . . . . . . . . . . . . . . . . . . . . . . . . . . kilowatts (kW). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.7457 foot-pounds per second (ft-lb per sec) . . . . . . . . . . . . . . . . . . 550 foot-pounds per minute (ft-lb per min.). . . . . . . . . . . . . . . . . . 33000 kilowatts (kW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . horsepower (hp) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.341 Use This TEMPERATURE Relationship

Conveyor Components

POWER


DYNA-SYNC

ENGINEERING/TECHNICAL GRAVITATIONAL CONSTANT g

= 32.174 feet per second per second (ft per sec2) = 9.8067 meters per second per second (m per sec2)

APPROXIMATE DENSITIES OF COMMON MATERIALS REPRESENTATIVE DENSITIES Grams per cc lb per cu ft HT Synchrous Belts

GASES @ 68F, std atm Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.30 grams per liter Oxygen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.45 grams per liter Hydrogen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.09 grams per liter Nitrogen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.25 grams per liter All Other Materials grams per cc

........ ........ ........ ........

0.07528 0.08305 0.005234 0.07274

LIQUIDS

Sprockets

Water @ 4C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.000 grams per cc . . . . . . . . 20C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.998 . . . . . . . . . . . . . . . . . . . 40C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.992 . . . . . . . . . . . . . . . . . . . SeaWater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.02-1.03 . . . . . . . . . . . . . . . . Ethyl alcohol 100% . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.789 . . . . . . . . . . . . . . . . . . . Kerosene . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.78-0.82 . . . . . . . . . . . . . . . . Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.70-0.75 . . . . . . . . . . . . . . . .

62.43 62.32 61.94 64.00 49.2 50 45

METALS

Conveyor Components

Aluminum (95% Al) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.70 . . . . . . . . . . . . . . . . . . . . Bronze (90% Cu, 10% Zn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.80 . . . . . . . . . . . . . . . . . . . . Copper (Annealed, ACS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.89 . . . . . . . . . . . . . . . . . . . . Gold. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.32 . . . . . . . . . . . . . . . . . . . Iron, gray cast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.10 . . . . . . . . . . . . . . . . . . . . Lead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.36 . . . . . . . . . . . . . . . . . . . Magnesium . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.74 . . . . . . . . . . . . . . . . . . . . Steel (0.4-0.5%Carbon) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.80 . . . . . . . . . . . . . . . . . . . . Steel, 410 stainless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.70 . . . . . . . . . . . . . . . . . . . .

169 549 555 1206 443 709 109 487 480

ENGINEERING PLASTICS

Engineering

ABS, general purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.01-1.05 . . . . . . . . . . . . . . . . Acrylics, cast sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.19 . . . . . . . . . . . . . . . . . . . . Nylon 6/6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.13-1.15 . . . . . . . . . . . . . . . . Phenolic, general purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.35-1.46 . . . . . . . . . . . . . . . . Polycarbonates, general purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 . . . . . . . . . . . . . . . . . . . . . Polyesters, thermoplastic, unreinforced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.31 - 1.43 . . . . . . . . . . . . . . . Polyehtylene, medium density. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.926-0.940 . . . . . . . . . . . . . . Polyvinyl Chloride . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.30-1.58 . . . . . . . . . . . . . . . .

PT14-32

64 74 71 87 75 86 58 89


APPROXIMATE DENSITIES OF COMMON MATERIALS REPRESENTATIVE DENSITIES Grams per cc lb per cu ft

DYNA-SYNC

ENGINEERING/TECHNICAL

32 48 33 32 48 44 62 48

Formulas and Constants 1 Kilometer =.62137 miles. 1 Gallon = 231 cubic inches. 1 Barrel = 31.5 gallons. Atmospheric Pressure = 14.7 pounds per sq. in. = 29.92 inches mercury at 32F. 1 Lb. per Sq. In. Pressure = 2.3095 feet fresh water at 62F. = 2.0355 inches mercury at 32F. = 2.0416 inches mercury at 62F. Water Pressure (pounds per sq. in.) =.433 X height of water in feet (Fresh water at 62F.). Weight of 1 cu. ft. fresh Water = 62.355 Ibs. at 62F. = 59.76 lbs. at 212F. Weight of 1 cu. ft. Air at 14.7 Ibs. per sq. in. Pressure = .07608 Ibs. at 62F. =.08073 lbs. at 32F.

â€

Also look in the General Index under Weights, Measures, or the subject material required.

Engineering

1 HP = 33,000 Foot-pounds of work per minute. 1 HP =.746 K.W. = K.W.P 1.341. 1 HP = 2547 B.T.U. per hour. 1 B.T.U. = Heat required to raise 1 lb. water 1F. 1 B.T.U. = 777.6 Foot-pounds work. 1 Kilowatt Hour = 3415 B.T.U. Heat Value of Carbon = 14,600 B.T.U. per pound. Latent Heat of Fusion of Ice = 143.15 B.T.U. per pound. Latent Heat of Evaporation of Water at 212F. = 970.4 B.T.U. per pound. Total Heat of Saturated Steam at atmospheric pressure = 1,150.4 B.T.U. per pound. 1 Ton of Refrigeration = 288,000 B.T.U. per 24 hours. g = Acceleration of Gravity (commonly taken as 32.16 feet per second per second). 1 Radian = 57.296 degrees. 1 Meter = 100 cm. = 39.37 inches.

Sprockets

144 94 100 83 78

Conveyor Components

Concrete (stone and sand) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2-2.4 . . . . . . . . . . . . . . . . . . Limestone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 . . . . . . . . . . . . . . . . . . . . . Anthracite coal, not piled. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4-1.8 . . . . . . . . . . . . . . . . . . Bituminous coal, not piled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2-1.5 . . . . . . . . . . . . . . . . . . Lignite coal, not piled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1-1.4 . . . . . . . . . . . . . . . . . . Wood, air dried: Douglas fir. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.48-0.55 . . . . . . . . . . . . . . . . White oak . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.77 . . . . . . . . . . . . . . . . . . . . White maple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.53 . . . . . . . . . . . . . . . . . . . . Oregon pine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.51 . . . . . . . . . . . . . . . . . . . . Hickory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.74-0.80 . . . . . . . . . . . . . . . . Mahogany . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.56-0.85 . . . . . . . . . . . . . . . . African teak. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.99 . . . . . . . . . . . . . . . . . . . . Indian teak . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.66-0.88 . . . . . . . . . . . . . . . .

HT Synchrous Belts

OTHER MATERIALS

PT14-33


DYNA-SYNC

ENGINEERING/TECHNICAL Flywheel Formulas Flywheels are used on some machines, for example air compressors, to even out load pulsations. The following formulas are useful in designing entire flywheels and flywheel rims. A V-belt sheave may also be used as a flywheel eliminating the need for a separate flywheel in the system.

and F respectively. When arms are used instead of a web an approximate WR2 value of the arms is the total weight of the arms in pounds times the square of the radius in feet from the shaft center line to the mid point of the arms between hub and rim.

Table 30: Formulas for Flywheel Rims

Formulas for Entire Flywheel HT Synchrous Belts

Kinetic energy of rotation of a flywheel (foot pounds) =.0001705 N2(WR2)*.

Property

Torque to uniformly accelerate or decelerate a flywheel =

.03908 (N2-N1) (WR2), * pound-inches

C

t

Cast Iron Rim (Based on.26 Ibs. per cu. in.)

Steel Rim (Based on.283 lbs. per cu. in.)

4F 2- 2

4F 2- 2

2042F 2- 2

222 F 2- 2

Rim of any material weighing K pounds per cubic inch 4F 2- 2

I

where N2 = final R.P.M. and N1 = initial R.P.M. Velocity at outside diameter (feet per minute) = 0.2618 ND.

4F

2- 2

P R

Sprockets

W = weight (pounds). R = radius of gyration (feet). N = speed (R.P.M.) t = time to change from N1 to N2 (seconds).

2) 0 2) 2) 0 1( 2 1( 2 0 1( 2 --------------------------------------------- t --------------------------------------------- --------------------------------------------1000 1000 1000

R G F R2 S

F = face of rim (inches). D = outside diameter of rim (inches). d = inside diameter of rim (inches). K = weight per cubic inch of material (pounds).

Conveyor Components

*WR2 = flywheel effect (pounds X feet2). See table to the right for WR2 of rims. Ordinarily the WR2 of the rim only is considered. In unusual instances the relatively small WR2 values of the hub and arms or web can be added directly to the WR2 of the rim if desired. To find the WR2 of a hub or web use the WR2 formula for rims, substituting the hub or web outside diameter, inside diameter, and width for D, d

1 F 4- 4 1 2 F 4- 4 1 F 4- 4 R 1000 1000 1000 G L F 2 Tâ–˛ 0FN2 1 1 4F N2 0 FN2 T L 1 000 000 1 000 000 1 000 000 L â–˛ Centrifugal force causes this tensile load at each and every section of the rim. Hence, on rims split into two or more sections the fastening at each joint should be designed to take the full load as calculated from the formula here given.

Centrifugal Force

Engineering

R = Distance from the axis of rotation to the center of gravity of the body (feet). N = Revolutions per minute. v = Velocity of the center of gravity of the body (feet per second). g = Acceleration due to gravity (32.16 commonly).

F = Wv2 gR

= WRN2 =.000341 WRN2 2933

F = Centrifugal force tending to move the body outward from the axis of rotation (pounds). W = Weight of body (pounds).

PT14-34


DYNA-SYNC

ENGINEERING/TECHNICAL Torque and Horsepower Equivalents TORQUE It is: a turning moment or twisting effort. Is it expressed in foot-pounds? or pound-feet?

A pound-foot is the moment created a force of one pound applied to the end of a lever arm one

FOOT-POUNDS INDICATE ENERGY T

P T

F FP RP L

I P L

F R A

-I -F

POUND-FEET INDICATE TORQUE Example:-

02 HP RP F L A 2 2 HP RP F L A

2 HP 2 HP RP T

I I F I F

1 0 RP 1 0 RP

10 04 P 10 0 4 P

-I -I

T T

-I

T

RP

P

HT Synchrous Belts

A foot-pound is the amount of energy expended in lifting a one-pound mass a distance of one foot against the pull of gravity

Example:-

P

2 HP 1 0 RP 2 HP 1 0 RP 2 HP 1 0 RP

P F

I

F

10 04 P 10 0400 P 10 040 P

-I -I

T T

Sprockets

HORSEPOWER Common Unit of Mechanical power - (HP) One HP is the rate of work required to raise 33,000 pounds one foot in one minute

Overhung Loads A

T

I

F= O OHL HP N R F

000 HP N R

F

{

F F 1 00 1 TI ING B 12 1 0 2 0

Conveyor Components

-

HT 2 0

Example F 0 RP

T RP R F

T

10

1 Solution: O.H.L. =

000

1

12

= 4,780 lbs.

0

Mathematical Equations 141 1 1 4 1/2

2 141 2 1 4142 4 44

4

0 22 1 T

T T T A A

0 0 1 4 442 11 4

A A T

1 12 4 00 4

PT14-35

Engineering

T T T T T T T T


DYNA-SYNC

ENGINEERING/TECHNICAL Table 31: Strength and Physical Properties of Various Metals Metals and Alloys

HT Synchrous Belts Sprockets Conveyor Components

A A A A A A A A A A A B B B B B B B B B B B B B B B B B B B B C C I I I I I I I I I I I I I L

Engineering

N N S S S S S S S S S ✝ ▲C

T T T T T T T T T T T A A C C N N R R R R S S A C

1100 0 A 1100-H1 H 00 -0 A 00 -H1 H 0 2-0 A 0 2-H H 0 -0 A 2014-0 A 2014-T4 H T C4A C S S C A C A A 0 A 0 H A L

1 1 L L -R -R

A A H C C L L A H A C 10 A A

G G C C

H

4A 4B G G

T

A B

A

P T H L C T L C B A E T P A C S C S P E A S P E A C C 0 C C I H R C 2 10 C 01 N C 0-4 -10 N I C 0- 0P H R H R A E AST IA A E AST A IA-F A C AST IB A C AST A 2A A C AST A IA C S C S P E A E A S P C C S A C C C 0 000 N C L A C 100 000 N T C L A C 120 000 T C L A C 200 000 T S S A T 04 1 S T 41 S B B AST A S H S L A AST A242 C A III

Stress in Thousands of Pounds per Sq. Inch Tension Tension Compression Shear Ultimate Yield Point Ultimate Ultimate 1 24 22 1 1 11 2 2 1 2 1 1 42 24 42 22 2 2 14 1 2 42 2 1 1 ▲ 24 0 1 1 ▲ 1 22 0 2 44 11 2 44 ✝ 2 ✝ 40 ✝ ✝ 2 ✝ ✝ 10 1 0 42 -4 1 -24 10-12▲ 012-1 11-12▲ 2 1 -1 0-40 12-1 -10▲ 4 14 2 4 0 4 2 -4 ✝ 10✝ 2 ✝ ✝ 0✝ 42 ✝ 4014-24 2 11-22 12-1 ▲ -4 1 -2 -1 ▲ 0- 0 2 - ✝ 0- 0 ✝ 2✝ 10✝ 22 ✝ - 0 0-120 0-100 0-100✝ 0-4 ✝ 110-1 0✝ 4 - ✝ 0- 4 11 44 -40 12 4 44 2 0 0 4 0 1 0 4 120 0 0 1 0 0- 0 40- 0 4-4 2 -24 4 0-4 2 -2 2 -2 10-1 1 40-4 22- 2 1 -21 21 14 4 0 11 24 14 1 2 20 - 0 2-4 120-14 0-1 0 2 -4 ✝ 0- ✝ 0-10 ✝ 40- ✝ 2 4 21 40 01 - 0 4 - ✝ 1 - 0✝ 0 100 120 200 1 0 4 2 40 0- 2 - 0 41

PT14-36

42- 0

▲ 42- 0▲ 0▲

4 - 4 4 1

Modulus of Elasticity Elongation% Millions of PSI 10 4 10 1 10 40 10 10 10 20 0 10 20 10 0 10 0 1 10 0 20 0 1 1 1 1 1 1 1 1 1-14 -14 10-14 1 1 1 -1 1 1 1 -1 -1 10 -1 1 1 2 2 1 1 1 1 2 0 2 2 22-2 22-2 2 2 0 0 0 0 0 2 24 20 2 2 -4 1 21 0 1 -1 0 2 - 0 2 - 0 2 - 0 2 - 0 2 2 2 - 0 2 - 0

4 ✝ 40✝ 4 201 -2 1 - 0 204 ✝ ✝ 4 - 0 -20 1 -40 - 0✝ 4 ✝ 10-20 1- ✝ 40- ✝ 4 10-1 1 -2 10-2 -10 -12 1-4 -11 1 -1 2 4 20- 0 1-4 - 0✝ - ✝ 4 1 - 0 - 0 2 20 1 1 -2 - 0 0 21 1 -24 10


Table 32: Properties of Sections Z = section modulus π k = radius of gyration y = centroidal distance

A = area I = moment of inertia J = polar moment of inertia

DYNA-SYNC

ENGINEERING/TECHNICAL

Rectangle A = bh

I=

bh 3 12

Z=

bh 2 6

A=

bh 2

I=

bh3 36

Z=

bh2 24

A=

y=

HT Synchrous Belts

k = 0.289h h 2

Triangle k = 0.236h h 3

πd 2 4

J=

πd 4 32

I=

πd 4 64

k=

d 4

Z=

πd 3 32

y=

d 2

πd (d4 - d 4) i 32

Sprockets

y=

+

Conveyor Components

Circle

+

A=

πd (d2 - d 2) i 4

J=

I=

πd 4 (d - di4) 64

k=

Z=

πd 4 (d - di4) 32d

d2 + d ----------------------i 16 d y= 2

PT14-37

2

Engineering

Hollow Circle


DYNA-SYNC

ENGINEERING/TECHNICAL Hardness Comparison Chart

Table 33: Coefficients of Friction “f” Material A C C C C

Static LubriDry cated 1 0 0

Sliding Dry

Lubricated

0 20 0 22

0 10 0 10

0 HT Synchrous Belts Sprockets

C C C C C C C C C C C E G H N O O O R S S S S S S S S S S

1 10 10 0 0 01 0 0 2 -1 0 0 4 0 0-0 0 1 10 0 0-0 0 0 2 0 4 0 -0 0 -0 00 0 42-0 0 0 0 -0 2 0 0 11-0 2 0 1 0 1 0 0 4 0 0 01

0 0 -0 0 0 11

-0 40 0 0 0 22 0 0 -0 0 01 0 0 -0 10 02 04 0 1 -0 0 0-0 0 0 0 -0 20 02 02 1/0/00 11 0 2 0 21

0 40 0 40-0 0 0 0 12 0 0-0 0 04 01 0 2 00 0 -0 0 -0 0 01 0 -0 0 0 -0 1 0 42 0 0 -0 12 04 0 44 0 4 01 0 01 0 0 0 -0 1 01 0 44

0 0 -0 10

Conveyor Components

Table 34: U.S. Standard Sheet Metal Gages Gage No. 1 2 4

Engineering

10 11 12 1 14 1 1 1 1 1

Thickness in Decimal Parts of an Inch 2 1 2 2 1 2242 20 2 1 4 1 1 44 14 1 4 11 104 0 0 4 0 0 0 04 041

Gage No. 20 21 22 2 24 2 2 2 2 2 0 1 2 4

Thickness in Decimal Parts of an Inch 0 0 2 02 02 02 020 01 01 4 014 01 0120 010 0102 00 4 00 00 00 0 00 00

* Shaded area indicates values may vary depending on type of ball used ▲Example: A Brinell number of 245 is equal to 62

Rockwell “A”, 100 Rockwell “B”, 23 Rockwell “C”, 37 Shore with a tensile of approximately 120,000 psi.

PT14-38


DYNA-SYNC

ENGINEERING/TECHNICAL

SINE

To Find Angles To Find: Formulas

T L T L H

To Find Angles Formulas 2

C

2

---

COSINE C

C

C

C

C

S

B

S

TANGENT C

T

C

C

C

C

C

B

C

S

C

S

C

C

C

C

{ { {

H H S S H H S S S S S S

B

S C T C C S C T C S S C

C

B

T

B B

B

C

B

B

S

B

B

C

B

S

B

C

C

T

B

C

C

C

B

S

C

C

B

T

C

B

S

C

C

B

T

2– 2 C

C ---

2– 2

B

B

C

COSECANT S

B

S

SECANT

B

C

C

COTANGENT

Table 36: Formulas for Finding Sides of Right Angle Triangles with an Angle and Side Known T L

S

C

To Find:

Sprockets

S H S H S S S S H S H S

Table 37: To Find Angles and Sides of Right Angle Triangles

C ---

S

B

C

C

T

B

C

Conveyor Components

Table 35: Formulas for Finding Functions of Angles

HT Synchrous Belts

Trigonometric Formula

C

Table 38: To Find Angles and Sides of Oblique Angle Triangle

Oblique Angle Triangle

Known A B B A A C

T

A B

S

C A C

B

A

Formulas 1 0 A B S B S A S C S A S C C C 1 0 - A C S A PT14-39

To Find: A

Known B C

C

A

S

C

A

C

B

C C B

---

---

Formulas 1 0- B C 2 2- 2 2 S A C

Engineering

To find: C

C S

C C -----

B


DYNA-SYNC

ENGINEERING/TECHNICAL NEMA QUICK REFERENCE CHART

S

R

• •

Dimensins are for reference only Drawings represent standard TEFC genearl purpose motors Contact your local Rockwell Automation office or go to the Motor Information Cent at 222.reliance.com for “C” dimensions

FRAME

U

4

14 T 1 2T 21 T 2 4T

14 T 1 4T 21 T 2 T

TAP 4 HOLES

HT Synchrous Belts

C AB

C

4

NEMA SHAFT U 1/2 / / 1-1/ 1- / 1- /

FRAME 2 4T 24T 4T 404T 444T 44 T

2 T 2 T T 40 T 44 T 44 T

NEMA SHAFT U 1- / 2-1/ 2- / 2- / - / - /

KEYSEAT DIMENSIONS R S 1-1 / 2 1/2 1-2 / 2 1/2 2-1/ 4 / 2-2 / 4 /4 2- / / 2- / /

P AB

AH

P

KEYSEAT DIMENSIONS R S 2 / 4 FLAT / 4 /1 4 / 4 /1 / 4 1/4 1-1 / 4 /1 1-1 / 2 /

45 TAP 4 HOLES

NEMA C-FACE 14 TC - 14 TC 1 2TC - 1 4 TC 21 TC - 21 TC 2 4TC- 2 TC

O V N-W

D (2)

U

V

U

AK

E

BA

2F

H

AA

AA CONDUIT

N-W

NEMA Frame 4

Sprockets Conveyor Components Engineering

H 14 T 14 T 1 2 1 4 1 2T 1 4T 21 21 21 T 21 T 2 4U 2 U 2 4T 2 T 2 4U 2 U 2 4T 2 T 2 4TS 2 TS 24U 2 U 24T 2 T 24TS 2 TS 4U U 4T T 4TS TS 404U 40 U 404T 40 T 404TS 40 TS 444U 44 U 444T 44 T 44 T 44 T 444TS 44 TS 44 TS 44 TS

D -1/2 -1/2 -1/2 -1/2 4-1/2 4-1/2 4-1/2 4-1/2 -1/4 -1/4 -1/4 -1/4 -1/4 -1/4 -1/4 -1/4

E

2F

H

N-W

O

P

U

2-1/ 2- /1 2- /1 2- /1 2- /4 - /4 - /4 - /4 - /4 4-1/4 4-1/4 4-1/4 4-1/4

2- /4

11/ 2 SLOT 11/ 2 SLOT 11/ 2 11/ 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 1 / 2 21/ 2 21/ 2 21/ 2 21/ 2 21/ 2 21/ 2 21/ 2 21/ 2 21/ 2 21/ 2 21/ 2 21/ 2 1 /1 1 /1 1 /1 1 /1 1 /1 1 /1 1 /1 1 /1 1 /1 1 /1 1 /1 1 /1 1 /1 1 /1 1 /1 1 /1

1-1/2 1- / 1- / 2-1/4 2-1/4 2-1/4 2-1/4 2- /4 2- /4

-1 /1 - /1 - /1 - /1 - /1 - / - / - / - / 11-1/4 11-1/4 11-1/4 11-1/4 1 -1/4 1 -1/4 1 -1/4 1 -1/4 14- /4 14- /4 14- /4 14- /4 14- /4 14- /4 1 -11/1 1 -11/1 1 -11/1 1 -11/1 1 -11/1 1 -11/1 1 -1/2 1 -1/2 1 -1/2 1 -1/2 1 -1/2 1 -1/2 21- /1 21- /1 21- /1 21- /1 21- /1 21- /1 2 - / 2 - / 2 - / 2 - / 2 - / 2 - / 2 - / 2 - / 2 - / 2 - /

- / - / 2 - / 2 - / 2 - / 2 -1/4 -1/4 -1/4 -1/4 10-1/2 10-1/2 10-1/2 10-1/2 1 -1/4 1 -1/4 1 -1/4 1 -1/4 14- / 14- / 14- / 14- / 14- / 14- / 1 1 1 1 1 1 1 -1/2 1 -1/2 1 -1/2 1 -1/2 1 -1/2 1 -1/2 22-1/2 22-1/2 22-1/2 22-1/2 22-1/2 22-1/2 2 -1/4 2 -1/4 2 -1/4 2 -1/4 2 2 2 -1/4 2 -1/4 2 2

1/2 / / / / / / 1-1/ 1-1/ 1-1/ 1-1/ 1- / 1- / 1- / 1- / 1- / 1- / 1- / 1- / 1- / 1- / 1- / 1- / 1- / 1- / 2-1/ 2-1/ 1- / 1- / 2-1/ 2-1/ 2- / 2- / 1- / 1- / 2- / 2- / 2- / 2- / 2-1/ 2-1/ 2- / 2- / - / - / - / - / 2- / 2- / 2- / 2- /

-1/2 -1/2 -1/2 -1/2 -1/2 -1/2 -1/4 -1/4 -1/4 -1/4 -1/4 -1/4

10 10 10 10 10 10 11 11 11 11 11 11 11 11 11 11

AJ

4 4-1/2 -1/2 4-1/2 -1/2 -1/2 -1/2 -1/4 10 -1/4 10 -1/2 11 -1/2 11 -1/2 11 10-1/2 12 10-1/2 12 10-1/2 12 11-1/4 12-1/4 11-1/4 12-1/4 11-1/4 12-1/4 12-1/4 1 - /4 12-1/4 1 - /4 12-1/4 1 - /4 14-1/2 1 -1/2 14-1/2 1 -1/2 20 2 14-1/2 1 -1/2 20 2

- / - / - /4 - /4 4 4 4- / 4- / 4- / 4- / -1/4 -1/4 - / - / -1/4 -1/4 - /4 - /4 - / - / - / - / - /4 - /4 -1/ -1/ -1/4 -1/4 4-1/4 4-1/4 - / - / -1/2 -1/2 -1/2 -1/2 4- /4 4- /4 4- /4 4- /4

Keyway /1 /1 /1 /1 /1 /1 1/4 1/4 1/4 1/4 /1 /1 /1 /1 / / / / 1/2 1/2 / / 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 / / 1/2 1/2 / / /4 /4 1/2 1/2 /4 /4 / / / / / / / /

PT14-40

/ 2 / 2 / 2 / 2 / 2 / 2 1/ 1/ 1/ 1/ / 2 / 2 / 2 / 2 /1 /1 /1 /1 1/4 1/4 /1 /1 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 /1 /1 1/4 1/4 /1 /1 / / 1/4 1/4 / / /1 /1 /1 /1 /1 /1 /1 /1

V

AA

AB

AH

AJ

1-1/2 1- / 1- / 2-1/4 2-1/4 2-1/4 2-1/4 2- /4 2- /4

1/2 1/2 1/2 /4 /4 /4 /4 /4 /4 1 1 1 1 1-1/4 1-1/4 1-1/4 1-1/4 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 2 2 2 2 2 2 2-1/2 2-1/2 2-1/2 2-1/2 2-1/2 2-1/2

- /1 - /1 -1 /1 -1 /1 - /1 - /1 -11/1 -11/1 10-1 /1 10-1 /1 10- /4 10- /4 12- / 12- / 12- /4 12- /4 12- /4 12- /4 1 - /1 1 - /1 1 - /1 1 - /1 1 - /1 1 - /1 1 1 1 -1/1 1 -1/1 1 -1/1 1 -1/1 1 -1/4 1 -1/4 1 - /1 1 - /1 1 - /1 1 - /1 22- /1 22- /1 2 - / 2 - / 2 - / 2 - / 2 - / 2 - / 2 - / 2 - /

1-11/1 2-1/1 2-1/1 2-1/ 2-1/ 2-1/ 2-1/ 2- / 2- / 2- /4 2- /4 -1/ -1/ -1/2 -1/2 - /4 - /4 4- / 4- / 4- / 4- /

- /4 - / - / - / - / - / - / -1/4 -1/4 -1/4 -1/4 -1/4 -1/4 -1/4 -1/4 -1/4 -1/4

- / - /

11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 14 14 14 14 14 14 14 14 14 14

- / - / - /4 - /4 4 4 4- / 4- / 4- / 4- / -1/4 -1/4 - / - / -1/4 -1/4 - /4 - /4 - / - / - / - / - /4 - /4 -1/ -1/ -1/4 -1/4 4-1/4 4-1/4 - / - / -1/2 -1/2 -1/2 -1/2 4- /4 4- /4 4- /4 4- /4

4 NPT 4 NPT

-1/2 -1/2 -1/ -1/ - / - / -1/2 -1/2 - / - /

4 4 - / - / -1/4 -1/4 -1/4 -1/4 4-1/2 4-1/2 4-1/2 4-1/2

BA Dimensions 2- /4 -1/2 4-1/4 4- /4

AK

BA

4-1/4 4-1/2 4-1/2 4-1/2 4-1/2 4-1/2 -1/2 -1/2 -1/2 -1/2 -1/2 -1/2 -1/2 -1/2 -1/2 -1/2 10-1/2 10-1/2 10-1/2 10-1/2 10-1/2 10-1/2 12-1/2 12-1/2 12-1/2 12-1/2 12-1/2 12-1/2 12-1/2 12-1/2 12-1/2 12-1/2 12-1/2 12-1/2 12-1/2 12-1/2 12-1/2 12-1/2 12-1/2 12-1/2 1 1 1 1 1 1 1 1 1 1

2-1/2 2- /4 2- /4 2-1/4 2-1/4 2- /4 2- /4 2- /4 2- /4 -1/2 -1/2 -1/2 -1/2 4-1/4 4-1/4 4-1/4 4-1/4 4- /4 4- /4 4- /4 4- /4 4- /4 4- /4 -1/4 -1/4 -1/4 -1/4 -1/4 -1/4 - / - / - / - / - / - / - / - / - / - / - / - / -1/2 -1/2 -1/2 -1/2 -1/2 -1/2 -1/2 -1/2 -1/2 -1/2

Tap Size 1/4-20 / -1 / -1 / -1 / -1 / -1 / -1 1/2-1 1/2-1 1/2-1 1/2-1 1/2-1 1/2-1 1/2-1 1/2-1 1/2-1 1/2-1 1/2-1 1/2-1 1/2-1 1/2-1 1/2-1 1/2-1 / -11 / -11 / -11 / -11 / -11 / -11 / -11 / -11 / -11 / -11 / -11 / -11 / -11 / -11 / -11 / -11 / -11 / -11 / -11 / -11 / -11 / -11 / -11 / -11 / -11 / -11 / -11 / -11


DYNA-SYNC

ENGINEERING/TECHNICAL IEC QUICK REFERENCE CHART • Dimensins are for reference only • Drawings represent standard TEFC genearl purpose motors Contact your local Rockwell Automation office or go to the Motor Information Cent at 222.reliance.com for “L” dimensions

MOUNTING:B14 L S

N P M 45

MOUNTING:B5 L S

N P M

45

HT Synchrous Belts

V

V

1 0 0 100 112S 112 1 2S 1 2 1 0 1 0L 1 0 1 0L 200 200L 22 S 22 2 0S 2 0 2 0S 2 0 2 0 2 0H L2 0H

A 12 140 1 0 1 0 1 0 21 21 2 4 2 4 2 2 1 1

B3 RIGID BASE L10 L12 HD 100 100 112 114

12 140 140

0

14 14

140 1 210 2 4 241 2 2 0 2 11

40 40 4 4 4 4 4

1 20 22 01 01

C

11

00 0

4 41 -

4 4 4 4 4 4 1 1

10 10 121 121 1 1 14 14 1 1 1 0 1 0 1 0 1 0 202

SHAFT E D 40 0 0 0 0 0 0 110 110 110 110 110 110 140 140 140 140 140 140 140 140 20

1 24 2 2 2

42 42 4 4

0 0

N 110 1 0 1 0 1 0 1 0 1 0 2 0 2 0 2 0 2 0 2 0 2 0 00 00 0 0

KEY AND KEYSEAT DIMENSIONS F GD FRAME D 1 0 1 0 4 200 22 0 2 0 0 10 2 0 0

M 1 0 1 1 21 21 21 2 2 00 00 00 00 0 0 400 400

B5 FLANGE P 1 0 200 200 2 0 2 0 2 0 00 00 0 0 0 0 400 400 4 0 4 0

S

4 4 4 4 4

V 11 11 14 14 14 14 14 1 1 1 1 1 1 1 1

LEGEND 1

0

PT14-41

G 42 42 4

F 12 14 1 1 20 22

1

N 0 0

M

110 110 110 1 0 1 0 1 0 1 0

100 11 1 0 1 0 1 0 1 1 21 21

442 442 4 0 4 0

44 44 4 0 4 0

GD

Sprockets

G 11 1 20 24 24

10 11 12 14

B14 FACE P S 10 2 120 140 1 0 1 0 1 0 200 200 2 0 4 2 0 4 40 40 0 0 0 0

V

12 12

AC 14 14 1 1 24 24 2 2 24 24

442 442 4 0 4 0 00 00 0 0 0 0 0

GENERAL AD XX 1 1 1 1 210 2 210 2 24 2 24 2 20 40 20 40 40 40 44 0 44 0 4 0 0 4 0 0 10

Conveyor Components

Frame

D 14 1 24 2 2

Engineering

FRAME 1 0 0 100 112 1 2


DYNA-SYNC

NOTES

HT Synchrous Belts

Sprockets

Conveyor Components

Engineering

PT14-42


Part No.

E

Page Part No.

000423. . . . . . . . . PT4-10 000424. . . . . . . . . PT4-10 000426. . . . . . . . . PT4-10 000427. . . . . . . . . PT4-10 000429. . . . . . . . . PT4-10 000430. . . . . . . . . PT4-10 000431. . . . . . . . . PT4-10 000432. . . . . . . . . PT4-10 000433. . . . . . . . . PT4-10 000434. . . . . . . . . PT4-10 000435. . . . . . . . . PT4-10 000436 . . . . . . . . . PT4-10 000437. . . . . . . . . PT4-10 000438. . . . . . . . . PT4-10 000439. . . . . . . . . PT4-10 000440. . . . . . . . . PT4-10 000441. . . . . . . . . PT4-10 000442. . . . . . . . . PT4-10 000443. . . . . . . . . PT4-10 000444. . . . . . . . . PT4-10 000445. . . . . . . . . PT4-10 000454. . . . . . . . . PT4-10 000455. . . . . . . . . PT4-10 000457. . . . . . . . . PT4-10 000458 . . . . . . . . PT4-10 000460 . . . . . . . . PT4-10 000461. . . . . . . . . PT4-10 000462. . . . . . . . . PT4-10 000463. . . . . . . . . PT4-10 000464. . . . . . . . . PT4-10 000465. . . . . . . . . PT4-10 000466 . . . . . . . . PT4-10 000467 . . . . . . . . PT4-10 000468 . . . . . . . . PT4-10 000469 . . . . . . . . PT4-10 000470 . . . . . . . . PT4-10 000471. . . . . . . . . PT4-10 000472. . . . . . . . . PT4-10 000473 . . . . . . . . PT4-10 000474. . . . . . . . . PT4-10 000475. . . . . . . . . PT4-10 000476. . . . . . . . . PT4-10 000478. . . . . . . . . PT1-19 000479. . . . . . . . . PT1-25 000480. . . . . . . . . PT1-19 000481. . . . . . . . . PT1-19 000482. . . . . . . . . PT1-19 000490. . . . . . . . . PT1-25 000492. . . . . . . . . PT1-25 000493. . . . . . . . . PT1-25 000494. . . . . . . . . PT1-25 000496. . . . . . . . . PT1-25 000498. . . . . . . . . PT1-25 000573. . . . . . . . . PT1-19 000574. . . . . . . . . PT1-25 000575. . . . . . . . . PT1-19 000576. . . . . . . . . PT1-19 000577. . . . . . . . . PT1-19 000578. . . . . . . . . PT1-19 000579. . . . . . . . . PT1-19 000580. . . . . . . . . PT1-19 000581. . . . . . . . . PT1-19 000582. . . . . . . . . PT1-19 000583. . . . . . . . . PT1-19 000584. . . . . . . . . PT1-19 000585. . . . . . . . . PT1-19 000586. . . . . . . . . PT1-19 000587. . . . . . . . . PT1-19 000588. . . . . . . . . PT1-19 000589. . . . . . . . . PT1-19 000590. . . . . . . . . PT1-19

N E Page Part No.

000591 . . . . . . . . . PT1-19 000592 . . . . . . . . . PT1-19 000593 . . . . . . . . . PT1-19 000594 . . . . . . . . . PT1-19 000595 . . . . . . . . . PT1-19 000596 . . . . . . . . . PT1-19 000597 . . . . . . . . . PT1-19 000598 . . . . . . . . . PT1-19 000599 . . . . . . . . . PT1-19 000600 . . . . . . . . . PT1-19 000601 . . . . . . . . . PT1-19 000602 . . . . . . . . . PT1-19 000603 . . . . . . . . . PT1-19 000604 . . . . . . . . . PT1-19 000605 . . . . . . . . .PT1-19 000606 . . . . . . . . . PT1-19 000607 . . . . . . . . . PT1-19 000608 . . . . . . . . . PT1-19 000609 . . . . . . . . . PT1-19 000610 . . . . . . . . PT1-19 000611 . . . . . . . . . PT1-19 000612 . . . . . . . . . PT1-19 000613 . . . . . . . . . PT1-19 000614 . . . . . . . . . PT1-19 000615 . . . . . . . . . PT1-19 000616 . . . . . . . . . PT1-19 000617 . . . . . . . . . PT1-19 000618 . . . . . . . . . PT1-19 000619 . . . . . . . . . PT1-19 000620 . . . . . . . . . PT1-19 000621 . . . . . . . . . PT1-19 000622 . . . . . . . . . PT1-19 000623 . . . . . . . . . PT1-19 000624 . . . . . . . . . PT1-19 000625 . . . . . . . . . PT1-19 000626 . . . . . . . . . PT1-19 000627 . . . . . . . . . PT1-19 000628 . . . . . . . . . PT1-19 000629 . . . . . . . . . PT1-19 000630 . . . . . . . . . PT1-19 000631 . . . . . . . . . PT1-19 000632 . . . . . . . . . PT1-19 000633 . . . . . . . . . PT1-19 000634 . . . . . . . . . PT1-19 000635 . . . . . . . . . PT1-19 000636 . . . . . . . . . PT1-19 000637 . . . . . . . . . PT1-19 000638 . . . . . . . . . PT1-19 000639 . . . . . . . . . PT1-19 000640 . . . . . . . . . PT1-19 000641 . . . . . . . . . PT1-19 000642 . . . . . . . . . PT1-19 000643 . . . . . . . . . PT1-19 000644 . . . . . . . . . PT1-19 000645 . . . . . . . . . PT1-19 000646 . . . . . . . . . PT1-19 000647 . . . . . . . . . PT1-19 000648 . . . . . . . . . PT1-19 000649 . . . . . . . . . PT1-19 000650 . . . . . . . . . PT1-19 000651 . . . . . . . . . PT1-19 000652 . . . . . . . . . PT1-19 000653 . . . . . . . . . PT1-19 000654 . . . . . . . . . PT1-19 000655 . . . . . . . . . PT1-19 000656 . . . . . . . . . PT1-19 000657 . . . . . . . . . PT1-19 000658 . . . . . . . . . PT1-19 000659 . . . . . . . . . PT1-19 000660 . . . . . . . . . PT1-19 000661 . . . . . . . . . PT1-19

000662 . . . . . . . . . 000663 . . . . . . . . . 000664 . . . . . . . . . 000665 . . . . . . . . . 000666 . . . . . . . . . 000667 . . . . . . . . . 000668 . . . . . . . . 000669 . . . . . . . . . 000670 . . . . . . . . . 000671 . . . . . . . . . 000672 . . . . . . . . . 000673 . . . . . . . . . 000674 . . . . . . . . . 000675 . . . . . . . . . 000676 . . . . . . . . . 000677 . . . . . . . . . 000678 . . . . . . . . . 000679 . . . . . . . . . 000680 . . . . . . . . . 000681 . . . . . . . . . 000682 . . . . . . . . . 000683 . . . . . . . . . 000684 . . . . . . . . . 000685 . . . . . . . . . 000686 . . . . . . . . . 000687 . . . . . . . . . 000688 . . . . . . . . . 000689 . . . . . . . . . 000690 . . . . . . . . . 000691 . . . . . . . . . 000692 . . . . . . . . . 000693 . . . . . . . . . 000694 . . . . . . . . . 000695 . . . . . . . . . 000696 . . . . . . . . . 000697 . . . . . . . . . 000698 . . . . . . . . 000699 . . . . . . . . 000700 . . . . . . . . 000701 . . . . . . . . 000702 . . . . . . . . 000703 . . . . . . . . 000704 . . . . . . . . 000705 . . . . . . . . 000706 . . . . . . . . 000707 . . . . . . . . 000708 . . . . . . . . 000709 . . . . . . . . 000710 . . . . . . . . 000711 . . . . . . . . 000712 . . . . . . . . 000713 . . . . . . . . 000714 . . . . . . . . 000715 . . . . . . . . 000716 . . . . . . . . 000717 . . . . . . . . 000718 . . . . . . . . . 000719 . . . . . . . . . 000720 . . . . . . . . . 000721 . . . . . . . . . 000722 . . . . . . . . . 000723 . . . . . . . . . 000724 . . . . . . . . . 000725 . . . . . . . . . 000726 . . . . . . . . . 000727 . . . . . . . . . 000728 . . . . . . . . . 000729 . . . . . . . . . 000730 . . . . . . . . . 000731 . . . . . . . . . 000732 . . . . . . . . .

Page Part No. PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-19 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25

000733 . . . . . . . . . 000734 . . . . . . . . . 000735 . . . . . . . . . 000736 . . . . . . . . . 000737 . . . . . . . . . 000738 . . . . . . . . . 000739 . . . . . . . . . 000740 . . . . . . . . . 000741 . . . . . . . . . 000742 . . . . . . . . . 000743 . . . . . . . . . 000744 . . . . . . . . . 000745 . . . . . . . . . 000746 . . . . . . . . . 000747 . . . . . . . . . 000748 . . . . . . . . . 000749 . . . . . . . . . 000750 . . . . . . . . . 000751 . . . . . . . . . 000752 . . . . . . . . . 000753 . . . . . . . . . 000754 . . . . . . . . . 000755 . . . . . . . . . 000756 . . . . . . . . . 000757 . . . . . . . . . 000758 . . . . . . . . . 000759 . . . . . . . . . 000760 . . . . . . . . . 000761 . . . . . . . . . 000762 . . . . . . . . . 000763 . . . . . . . . . 000764 . . . . . . . . . 000765 . . . . . . . . . 000766 . . . . . . . . . 000767 . . . . . . . . . 000768 . . . . . . . . . 000769 . . . . . . . . . 000770 . . . . . . . . . 000771 . . . . . . . . . 000772 . . . . . . . . . 000773 . . . . . . . . . 000774 . . . . . . . . . 000775 . . . . . . . . . 000776 . . . . . . . . . 000777 . . . . . . . . . 000778 . . . . . . . . . 000779 . . . . . . . . . 000780 . . . . . . . . . 000781 . . . . . . . . . 000782 . . . . . . . . . 000783 . . . . . . . . . 000784 . . . . . . . . . 000785 . . . . . . . . . 000786 . . . . . . . . . 000787 . . . . . . . . . 000788 . . . . . . . . . 000789 . . . . . . . . . 000790 . . . . . . . . . 000791 . . . . . . . . . 000792 . . . . . . . . . 000793 . . . . . . . . . 000794 . . . . . . . . . 000795 . . . . . . . . . 000796 . . . . . . . . . 000797 . . . . . . . . . 000798 . . . . . . . . . 000799 . . . . . . . . . 000800 . . . . . . . . . 000801 . . . . . . . . . 000802 . . . . . . . . . 000803 . . . . . . . . .

INDEX-1

Page Part No. PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25 PT1-25

000804 000822 000823 000824 000825 000826 000827 000828 000829 000830 000831 000832 000833 000836 000837 000838 000839 000840 000841 000842 000843 000844 000845 000846 000847 000848 000849 000850 000851 000854 000857 000858 000859 000860 000861 000862 000863 000864 000865 002245 003001 003002 003003 003004 003005 003006 003007 003008 003009 003010 003011 003012 003013 003014 003015 003016 003251 003252 003253 003254 003283 003284 003285 003286 003287 003288 003289 003291 003293 003323 003324

Page Part No.

. . . . . . . . . PT1-25 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-25 . . . . . . . . . PT1-25 . . . . . . . . . PT1-25 . . . . . . . . . PT1-25 . . . . . . . . . PT1-25 . . . . . . . . . PT1-25 . . . . . . . . . PT1-25 . . . . . . . . . PT1-25 . . . . . . . . . PT1-25 . . . . . . . . . PT1-25 . . . . . . . . . PT1-25 . . . . . . . . . PT1-25 . . . . . . . . . PT1-22 . . . . . . . . . PT1-22 . . . . . . . . . PT1-27 . . . . . . . . . PT1-29 . . . . . . . . . PT1-28 . . . . . . . . . PT1-28 . . . . . . . . . PT1-28 . . . . . . . . . PT1-28 . . . . . . . . . PT1-28 . . . . . . . . . PT1-28 . . . . . . . . . PT1-28 . . . . . . . . . PT1-29 . . . . . . . . . PT1-29 . . . . . . . . . PT1-29 . . . . . . . . . PT1-13 . . . . . . . . . PT1-65 . . . . . . . . . PT1-65 . . . . . . . . . PT1-65 . . . . . . . . . PT1-65 . . . . . . . . . PT1-65 . . . . . . . . . PT1-65 . . . . . . . . . PT1-65 . . . . . . . . . PT1-65 . . . . . . . . . PT1-65 . . . . . . . . . PT1-65 . . . . . . . . . PT1-65 . . . . . . . . . PT1-65 . . . . . . . . . PT1-65 . . . . . . . . . PT1-65 . . . . . . . . . PT1-65 . . . . . . . . . PT1-65 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19

003326 003328 003356 003357 003359 003361 003402 003403 003405 003407 003450 003451 003453 003455 003501 003502 003504 003506 004208 004209 004210 004211 004212 004213 004215 004216 004217 004219 004220 004222 004242 004243 004246 004252 004254 004498 004500 004505 004508 004510 004511 004513 004515 004516 004517 004520 004521 004522 004523 004524 004525 004527 004528 004529 004531 004534 004536 004538 004539 004540 004542 004543 004544 004545 004546 004547 004548 004550 004551 004552 004559

Page

. . . . . . . . PT1-19 . . . . . . . . PT1-19 . . . . . . . . PT1-19 . . . . . . . . PT1-19 . . . . . . . . PT1-19 . . . . . . . . PT1-19 . . . . . . . . PT1-19 . . . . . . . . PT1-19 . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . PT1-19 . . . . . . . . . . PT1-7 . . . . . . . . . . PT1-7 . . . . . . . . . . PT1-7 . . . . . . . . . . PT1-7 . . . . . . . . . . PT1-7 . . . . . . . . . . PT1-7 . . . . . . . . . . PT1-7 . . . . . . . . . . PT1-7 . . . . . . . . . . PT1-7 . . . . . . . . . . PT1-7 . . . . . . . . . PT1-7 . . . . . . . . . . PT1-7 . . . . . . . . . . PT1-7 . . . . . . . . . . PT1-7 . . . . . . . . . . PT1-7 . . . . . . . . . . PT1-7 . . . . . . . . . . PT1-7 . . . . . . . . . PT1-11 . . . . . . . . . PT1-11 . . . . . . . . . PT1-11 . . . . . . . . . PT1-11 . . . . . . . . . PT1-11 . . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . PT1-11 . . . . . . . . . PT1-11

INDEX

TN


TN

E

INDEX

Part No.

Page Part No.

004562 004565 004567 004568 004570 004573 004574 004575 004579 004581 004582 004583 004586 004587 004588 004590 004591 004592 004593 004594 004595 004596 004598 004600 004602 004603 004604 004606 004607 004608 004611 004612 004614 004615 004616 004618 004619 004620 004622 004623 004624 004625 004627 004629 004632 004633 004636 004637 004639 004640 004641 004643 004644 004645 004648 004649 004651 004653 004654 004656 004657 004658 004659 004660 004663 004664 004667 004668 004671 004672 004675

PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11 PT1-11

......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... .........

N E Page Part No.

004676 . . . . . . . . . PT1-11 004678 . . . . . . . . . PT1-11 004679 . . . . . . . . . PT1-11 004680 . . . . . . . . . PT1-11 004683 . . . . . . . . . PT1-11 004684 . . . . . . . . . PT1-11 004686 . . . . . . . . . PT1-11 004688 . . . . . . . . . PT1-11 004689 . . . . . . . . . PT1-11 004691 . . . . . . . . . PT1-11 004692 . . . . . . . . . PT1-11 004693 . . . . . . . . . PT1-11 004694 . . . . . . . . . PT1-11 004696 . . . . . . . . . PT1-11 004698 . . . . . . . . . PT1-11 004699 . . . . . . . . . PT1-11 004700 . . . . . . . . . PT1-11 004703 . . . . . . . . . PT1-11 004704 . . . . . . . . . PT1-11 004707 . . . . . . . . . PT1-11 004708 . . . . . . . . . PT1-11 004711 . . . . . . . . . PT1-11 004712 . . . . . . . . . PT1-11 004714 . . . . . . . . . PT1-11 004715 . . . . . . . . . PT1-11 004716 . . . . . . . . . PT1-11 004719 . . . . . . . . . PT1-11 004720 . . . . . . . . . PT1-11 004722 . . . . . . . . . PT1-11 004724 . . . . . . . . . PT1-11 004725 . . . . . . . . . PT1-11 004727 . . . . . . . . . PT1-11 004728 . . . . . . . . . PT1-11 004730 . . . . . . . . . PT1-11 004731 . . . . . . . . . PT1-11 004732 . . . . . . . . . PT1-11 004734 . . . . . . . . . PT1-11 004735 . . . . . . . . . PT1-11 004871 . . . . . . . . . PT1-11 004872 . . . . . . . . . PT1-11 004875 . . . . . . . . . PT1-11 004876 . . . . . . . . . PT1-11 004885 . . . . . . . . . PT1-11 004886 . . . . . . . . . PT1-11 004887 . . . . . . . . . PT1-11 004889 . . . . . . . . . PT1-11 004890 . . . . . . . . . PT1-11 004920 . . . . . . . . . PT1-11 004921 . . . . . . . . . PT1-11 004922 . . . . . . . . . PT1-11 004923 . . . . . . . . . PT1-11 004925 . . . . . . . . . PT1-11 004927 . . . . . . . . . PT1-11 004976 . . . . . . . . . PT1-11 004977 . . . . . . . . . PT1-11 004978 . . . . . . . . . PT1-11 004979 . . . . . . . . . PT1-11 004980 . . . . . . . . . PT1-11 004981 . . . . . . . . . PT1-11 004982 . . . . . . . . . PT1-11 004983 . . . . . . . . . PT1-11 004993 . . . . . . . . . PT1-11 004994 . . . . . . . . . PT1-11 004995 . . . . . . . . . PT1-11 004996 . . . . . . . . . PT1-11 004997 . . . . . . . . . PT1-11 004998 . . . . . . . . . PT1-11 006245 . . . . . . . . . PT1-47 006250 . . . . . . . . PT1-47, . . . . . . . . PT1-49, PT1-68

Page Part No.

006251 . . . . . . . . PT1-47, . . . . . . . . PT1-49, PT1-68 006252 . . . . . . . . PT1-47, . . . . . . . . PT1-49, PT1-68 006253 . . . . . . . . PT1-47, . . . . . . . . PT1-49, PT1-68 006254 . . . . . . . . PT1-47, . . . . . . . . PT1-49, PT1-68 006255 . . . . . . . . PT1-47, . . . . . . . . . PT1-49, PT1-68 006256. . . . . . . . . PT1-47, . . . . . . . . . PT1-49, PT1-68 006257. . . . . . . . . PT1-47, . . . . . . . . PT1-49, PT1-68 006258 . . PT1-47, PT1-68 006259. . PT1-47, PT1-68 006260 . . PT1-47, PT1-68 006261. . PT1-47, PT1-68 006262 . . PT1-47, PT1-68 006263 . . PT1-47, PT1-68 006264 . . PT1-47, PT1-68 006265 . . PT1-47, PT1-68 006266 . . PT1-47, PT1-68 006267 . . PT1-47, PT1-68 006268 . . PT1-47, PT1-68 006269 . . PT1-47, PT1-68 006275. . . . . . . . . PT1-47, . . . . . . . . . PT1-49, PT1-68 006276 . . . . . . . . PT1-47, . . . . . . . . PT1-49, PT1-68 006277 . . . . . . . . PT1-47, . . . . . . . . . PT1-49, PT1-68 006278 . . . . . . . . PT1-47, . . . . . . . . PT1-49, PT1-68 006279 . . . . . . . . PT1-47, . . . . . . . . . PT1-49, PT1-68 006280 . . . . . . . . PT1-47, . . . . . . . . . PT1-49, PT1-68 006281 . . . . . . . . PT1-47, . . . . . . . . PT1-49, PT1-68 006282 . . . . . . . . PT1-47, . . . . . . . . . PT1-49, PT1-68 006283 . . PT1-47, PT1-68 006284. . PT1-47, PT1-68 006290 . . . . . . . . . PT1-47 006291 . . . . . . . . . PT1-47 006292 . . . . . . . . . PT1-47 006293 . . . . . . . . . PT1-47 006294 . . . . . . . . . PT1-47 006295 . . . . . . . . . PT1-47 006296 . . . . . . . . . PT1-47 006297 . . . . . . . . . PT1-47 006298 . . . . . . . . . PT1-47 006299 . . . . . . . . . PT1-47 006300 . . . . . . . . . PT1-47 006301 . . . . . . . . . PT1-47 006305 . . . . . . . . . PT1-49 006306 . . . . . . . . . PT1-49 006307 . . . . . . . . . PT1-49 006308 . . . . . . . . . PT1-49 006309 . . . . . . . . . PT1-49 006310 . . . . . . . . . PT1-49 006311 . . . . . . . . . PT1-49 006312 . . . . . . . . . PT1-49 006318 . . . . . . . . . PT1-47 006319 . . . . . . . . . PT1-47 006320 . . . . . . . . . PT1-47 006321 . . . . . . . . . PT1-47 006322 . . . . . . . . . PT1-47 006323 . . . . . . . . . PT1-47 006324 . . . . . . . . . PT1-47

Page Part No.

006325 . . . . . . . . .PT1-47 006326 . . . . . . . . . PT1-47 006328 . . . . . . . . . PT1-49 006330 . . . . . . . . . PT1-49 006331 . . . . . . . . . PT1-49 006332 . . . . . . . . . PT1-49 006333 . . . . . . . . . PT1-49 006334 . . . . . . . . . PT1-49 006335 . . . . . . . . . PT1-49 006396 . . . . . . . . . PT1-49 006397 . . . . . . . . . PT1-49 006398 . . . . . . . . . PT1-49 006399 . . . . . . . . . PT1-49 006400 . . . . . . . . . PT1-49 006401 . . . . . . . . . PT1-49 006402 . . . . . . . . . PT1-49 006411 . . . . . . . . . PT1-49 006412 . . . . . . . . . PT1-49 006413 . . . . . . . . . PT1-49 006414 . . . . . . . . . PT1-49 006415 . . . . . . . . . PT1-49 006416 . . . . . . . . . PT1-49 006417 . . . . . . . . .PT1-49 006418 . . . . . . . . .PT1-49 006419 . . . . . . . . . PT1-49 006429 . . . . . . . . . PT1-49 006430 . . . . . . . . . PT1-49 006431 . . . . . . . . . PT1-49 006432 . . . . . . . . . PT1-49 006433 . . . . . . . . . PT1-49 006434 . . . . . . . . . PT1-49 006435 . . . . . . . . . PT1-49 006436 . . . . . . . . . PT1-49 006437 . . . . . . . . . PT1-49 006438 . . . . . . . . . PT1-49 006439 . . . . . . . . . PT1-49 006440 . . . . . . . . . PT1-49 006451 . . . . . . . . . PT1-49 006452 . . . . . . . . . PT1-49 006453 . . . . . . . . . PT1-49 006454 . . . . . . . . .PT1-49 006455 . . . . . . . . . PT1-49 006456 . . . . . . . . . PT1-49 006457 . . . . . . . . . PT1-49 006458 . . . . . . . . . PT1-49 006460 . . . . . . . . . PT1-47 006461 . . . . . . . . . PT1-47 006462 . . . . . . . . . PT1-47 006463 . . . . . . . . . PT1-47 006464 . . . . . . . . . PT1-47 006465 . . . . . . . . . PT1-47 006466 . . . . . . . . . PT1-47 006467 . . . . . . . . . PT1-47 006468 . . . . . . . . . PT1-47 006469 . . . . . . . . . PT1-47 006470 . . . . . . . . . PT1-47 006471 . . . . . . . . . PT1-47 006472 . . . . . . . . . PT1-47 006473 . . . . . . . . . PT1-47 006474 . . . . . . . . . PT1-47 006475 . . . . . . . . . PT1-47 006476 . . . . . . . . . PT1-47 006480 . . . . . . . . . PT1-47 006481 . . . . . . . . . PT1-49 006482 . . . . . . . . . PT1-49 006484 . . . . . . . . . PT1-47 006485 . . . . . . . . . PT1-47 006486 . . . . . . . . . PT1-47 006487 . . . . . . . . . PT1-47 006488 . . . . . . . . . PT1-47 006489 . . . . . . . . . PT1-47

INDEX-2

Page Part No.

006490 . . . . . . . . PT1-47 006491 . . . . . . . . . PT1-47 006492 . . . . . . . . . PT1-47 006493 . . . . . . . . . PT1-47 006494 . . . . . . . . . PT1-47 006497 . . PT1-50, PT1-51 006498 . . PT1-50, PT1-51 006499 . .PT1-50, PT1-51 006504 . . PT1-50, PT1-51 006505 . . PT1-50, PT1-51 006506 . . PT1-50, PT1-51 006507 . .PT1-50, PT1-51 006516 . .PT1-50, PT1-51 006517 . .PT1-50, PT1-51 006518 . . PT1-50, PT1-51 006519 . . PT1-50, PT1-51 006520 . . PT1-50, PT1-51 006533 . . PT1-50, PT1-51 006534 . . PT1-50, PT1-51 006535 . . PT1-50, PT1-51 006536 . . PT1-50, PT1-51 006539 . . . . . . . . . PT1-47 006540 . . . . . . . . . PT1-47 006541 . . . . . . . . . PT1-47 006544 . . PT1-50, PT1-51 006545 . . PT1-50, PT1-51 006546 . . PT1-50, PT1-51 006550 . . . . . . . . . PT1-49 006553 . . PT1-50, PT1-51 006554 . . PT1-50, PT1-51 006555 . .PT1-50, PT1-51 006560 . . . . . . . . . PT1-49 006561 . . PT1-50, PT1-51 006562 . . PT1-50, PT1-51 006563 . . .PT1-50, PT1-51 006564 . . . . . . . . . PT1-49 006565 . . . . . . . . . PT1-49 006566 . . . . . . . . . PT1-49 006567 . . . . . . . . . PT1-49 006568 . . . . . . . . . PT1-49 006569 . . PT1-50, PT1-51 006570 . . PT1-50, PT1-51 006571 . . . . . . . . . PT1-47 006572 . . . . . . . . . PT1-47 006573 . . . . . . . . . PT1-47 006576 . . . . . . . . . PT1-47 006577 . . . . . . . . . PT1-47 006578 . . . . . . . . . PT1-47 006579 . . . . . . . . PT1-47 006580 . . . . . . . . . PT1-47 006581 . . . . . . . . . PT1-47 006582 . . . . . . . . . PT1-47 006583 . . . . . . . . . PT1-47 006584 . . . . . . . . . PT1-47 006585 . . . . . . . . . PT1-47 006586 . . . . . . . . . PT1-47 006587 . . . . . . . . . PT1-47 006588 . . . . . . . . . PT1-47 006589 . . . . . . . . . PT1-47 006590 . . . . . . . . . PT1-47 006591 . . . . . . . . . PT1-47 006592 . . . . . . . . . PT1-47 006593 . . . . . . . . . PT1-47 006594 . . . . . . . . . PT1-47 006595 . . . . . . . . . PT1-47 006596 . . . . . . . . . PT1-47 006597 . . . . . . . . . PT1-47 006598 . . . . . . . . . PT1-47 006599 . . . . . . . . . PT1-47 006600 . . . . . . . . . PT1-47 006601 . . . . . . . . . PT1-47

Page

006602 . . . . . . . . . PT1-47 006603 . . . . . . . . . PT1-47 006604 . . . . . . . . . PT1-47 006605 . . . . . . . . . PT1-47 006606 . . . . . . . . . PT1-47 006607 . . . . . . . . . PT1-47 006608 . . . . . . . . . PT1-47 006609 . . . . . . . . . PT1-47 006610 . . . . . . . . . PT1-47 006611 . . . . . . . . . PT1-47 006612 . . . . . . . . . PT1-47 006613 . . . . . . . . . PT1-47 006614 . . . . . . . . . PT1-47 006615 . . . . . . . . . PT1-47 006616 . . . . . . . . . PT1-47 006617 . . . . . . . . . PT1-47 006618 . . . . . . . . . PT1-47 006619 . . . . . . . . . PT1-47 006620 . . . . . . . . . PT1-47 006621 . . . . . . . . . PT1-47 006622 . . . . . . . . . PT1-47 006623 . . . . . . . . . PT1-47 006624 . . . . . . . . . PT1-47 006625 . . . . . . . . . PT1-47 006626 . . . . . . . . . PT1-47 006627 . . . . . . . . . PT1-47 006628 . . . . . . . . . PT1-47 006629 . . . . . . . . . PT1-47 006640 . . . . . . . . . PT1-47 006641 . . . . . . . . . PT1-47 006642 . . . . . . . . . PT1-47 006643 . . . . . . . . . PT1-47 006656 . . . . . . . . . PT1-47 006657 . . . . . . . . . PT1-47 006750 . . PT1-47, PT1-49 006751 . . PT1-47, PT1-49 006752 . . PT1-47, PT1-49 006753 . . PT1-47, PT1-49 006754 . . PT1-47, PT1-49 006755 . . PT1-47, PT1-49 006756 . . PT1-47, PT1-49 006757 . . PT1-47, PT1-49 006758 . . . . . . . . . PT1-47 006759 . . . . . . . . . PT1-47 006760 . . . . . . . . . PT1-47 006765 . . . . . . . . . PT1-47 006767 . . . . . . . . . PT1-47 006768 . . . . . . . . . PT1-47 006769 . . . . . . . . . PT1-47 006770 . . . . . . . . . PT1-47 006771 . . . . . . . . . PT1-47 006772 . . . . . . . . . PT1-47 006773 . . . . . . . . . PT1-47 006774 . . . . . . . . . PT1-47 006790 . . . . . . . . . PT1-47 006791 . . . . . . . . . PT1-47 006792 . . . . . . . . . PT1-47 006793 . . . . . . . . . PT1-47 006794 . . . . . . . . . PT1-47 006795 . . . . . . . . . PT1-47 006796 . . . . . . . . . PT1-47 006797 . . . . . . . . . PT1-47 006798 . . . . . . . . . PT1-47 006799 . . . . . . . . . PT1-47 006800 . . . . . . . . . PT1-47 006801 . . . . . . . . . PT1-47 006802 . . . . . . . . . PT1-47 006803 . . . . . . . . . PT1-47 006804 . . . . . . . . . PT1-47 006805 . . . . . . . . . PT1-68 006806 . . . . . . . . . PT1-68


Part No.

E

Page Part No.

006807. . . . . . . . . PT1-68 006808. . . . . . . . . PT1-68 006809. . . . . . . . . PT1-68 006810. . . . . . . . . PT1-68 006811. . . . . . . . . PT1-68 006812 . . . . . . . . . PT1-68 006813 . . . . . . . . . PT1-68 006814 . . . . . . . . . PT1-68 006815. . . . . . . . . PT1-68 006816. . . . . . . . . PT1-68 006817. . . . . . . . . PT1-68 006818. . . . . . . . . PT1-68 006819. . . . . . . . . PT1-68 006820. . . . . . . . . PT1-68 006821. . . . . . . . . PT1-68 006822. . . . . . . . . PT1-68 006823. . . . . . . . . PT1-68 006824. . . . . . . . . PT1-68 006894 . . . . . . . . . PT1-49 006903 . . . . . . . . . PT1-49 006904 . . . . . . . . . PT1-49 006905 . . . . . . . . . PT1-49 006906 . . . . . . . . . PT1-49 006907 . . . . . . . . . PT1-49 006908. . . . . . . . . PT1-49 006909. . . . . . . . . PT1-49 006950. . . . . . . . . PT1-47 006951. . . . . . . . . PT1-47 006952. . . . . . . . . PT1-47 006953 . . . . . . . . . PT1-47 006954. . . . . . . . . PT1-47 006955. . . . . . . . . PT1-47 006956 . . . . . . . . . PT1-47 006957 . . . . . . . . . PT1-47 006958 . . . . . . . . . PT1-47 006959. . . . . . . . . PT1-47 006960. . . . . . . . . PT1-47 006961. . . . . . . . . PT1-47 006962. . . . . . . . . PT1-47 006963. . . . . . . . . PT1-47 006964. . . . . . . . . PT1-47 006965. . . . . . . . . PT1-47 006966. . . . . . . . . PT1-47 006967. . . . . . . . . PT1-47 006968. . . . . . . . . PT1-47 006969. . . . . . . . . PT1-47 006970. . . . . . . . . PT1-49 006971. . . . . . . . . PT1-49 006972. . . . . . . . . PT1-49 006973. . . . . . . . . PT1-49 006974. . . . . . . . . PT1-49 006984. . . . . . . . . PT1-49 006985. . . . . . . . . PT1-49 006986. . . . . . . . . PT1-49 006987. . . . . . . . . PT1-49 006988. . . . . . . . . PT1-49 006989. . . . . . . . . PT1-49 006990. . . . . . . . . PT1-49 006991. . . . . . . . . PT1-49 006992. . . . . . . . . PT1-49 008030. . . . . . . . . PT1-64 008030. . . . . . . . . PT3-14 008031. . . . . . . . . PT1-64 008032 . . PT1-64, PT3-14 008033. . PT1-64, PT3-14 008034 . . PT1-64, PT3-14 008035. . PT1-64, PT3-14 008036. . . . . . . . . PT1-64 008040. . PT1-64, PT3-14 008041 . . PT1-64, PT3-14 008042 . . PT1-64, PT3-14

N E Page Part No.

008043 . . PT1-64, PT3-14 008044 . . PT1-64, PT3-14 008045 . . PT1-64, PT3-14 008046 . . PT1-64, PT3-14 008047 . . PT1-64, PT3-14 008048 . . . . . . . . . PT1-64 008049 . . . . . . . . . PT1-64 008057 . . PT1-64, PT3-14 008058 . . PT1-64, PT3-14 008059 . . . . . . . . . PT1-64 008060 . . . . . . . . . PT1-64 008980 . . . . . . . . . PT1-33 008981 . . . . . . . . . PT1-33 008982 . . . . . . . . . PT1-33 008983 . . . . . . . . . PT1-33 008984 . . . . . . . . . PT1-33 008985 . . . . . . . . . PT1-33 008986 . . . . . . . . . PT1-33 008987 . . . . . . . . . PT1-33 008988 . . . . . . . . . PT1-33 008989 . . . . . . . . . PT1-33 008990 . . . . . . . . . PT1-33 008991 . . . . . . . . . PT1-33 008992 . . . . . . . . . PT1-33 008993 . . . . . . . . . PT1-33 009001 . . . . . . . . . PT1-66 009002 . . . . . . . . . PT1-66 009004 . . . . . . . . . PT1-66 009005 . . . . . . . . . PT1-66 009006 . . . . . . . . . PT1-66 009007 . . . . . . . . . PT1-66 009008 . . . . . . . . . PT1-66 009009 . . . . . . . . . PT1-66 009010 . . . . . . . . . PT1-66 009011 . . . . . . . . . PT1-66 009012 . . . . . . . . . PT1-66 009013 . . . . . . . . . PT1-66 009014 . . . . . . . . . PT1-66 009015 . . . . . . . . . PT1-66 009016 . . . . . . . . . PT1-66 009017 . . . . . . . . . PT1-66 009019 . . . . . . . . . PT1-66 009020 . . . . . . . . . PT1-66 009021 . . . . . . . . . PT1-66 009022 . . . . . . . . . PT1-66 009023 . . . . . . . . . PT1-66 009024 . . . . . . . . . PT1-66 009025 . . . . . . . . . PT1-66 009026 . . . . . . . . . PT1-66 009027 . . . . . . . . . PT1-66 009028 . . . . . . . . . PT1-66 009029 . . . . . . . . . PT1-66 009031 . . . . . . . . . PT1-66 009042 . . . . . . . . . PT1-66 009043 . . . . . . . . . PT1-66 009044 . . . . . . . . . PT1-66 009050 . . . . . . . . . PT1-66 009054 . . . . . . . . . PT1-66 009199 . . . . . . . . . PT1-19 009214 . . . . . . . . . PT1-19 009215 . . . . . . . . . PT1-19 009223 . . . . . . . . . PT1-19 009230 . . . . . . . . . PT1-19 009419 . . . . . . . . . PT1-29 009420 . . . . . . . . . PT1-29 009421 . . . . . . . . . PT1-29 009422 . . . . . . . . . PT1-29 009423 . . . . . . . . . PT1-29 009424 . . . . . . . . . PT1-29 009425 . . . . . . . . . PT1-29 009426 . . . . . . . . . PT1-29

Page Part No.

009427 . . . . . . . . PT1-29 009428 . . . . . . . . . PT1-29 009429 . . . . . . . . PT1-29 009430 . . . . . . . . . PT1-29 009431 . . . . . . . . . PT1-29 009432 . . . . . . . . . PT1-29 009433 . . . . . . . . . PT1-29 009434 . . . . . . . . . PT1-29 009435 . . . . . . . . . PT1-29 009436 . . . . . . . . . PT1-29 009437 . . . . . . . . . PT1-29 009438 . . . . . . . . . PT1-29 009439 . . . . . . . . . PT1-29 009440 . . . . . . . . PT1-29 009441 . . . . . . . . . PT1-29 009442 . . . . . . . . . PT1-29 009443 . . . . . . . . . PT1-29 009444 . . . . . . . . . PT1-29 009445 . . . . . . . . . PT1-29 009446 . . . . . . . . . PT1-29 009447 . . . . . . . . . PT1-29 009448 . . . . . . . . . PT1-29 009449 . . . . . . . . PT1-29 009450 . . . . . . . . PT1-29 009451 . . . . . . . . . PT1-29 009452 . . . . . . . . . PT1-29 009453 . . . . . . . . . PT1-29 009454 . . . . . . . . . PT1-29 009455 . . . . . . . . . PT1-29 009456 . . . . . . . . . PT1-29 009457 . . . . . . . . . PT1-29 009903 . . . . . . . . . PT1-66 010019 . . . . . . . . . . PT9-7 010020 . . . . . . . . . . PT9-7 010021 . . . . . . . . . . PT9-7 010024 . . . . . . . . . . PT9-7 010028 . . . . . . . . . . PT9-7 010029 . . . . . . . . . . PT9-7 010032 . . . . . . . . . . PT9-7 010036 . . . . . . . . . . PT9-7 010039 . . . . . . . . . . PT9-7 010043 . . . . . . . . . . PT9-7 010048 . . . . . . . . . . PT9-7 010051 . . . . . . . . . . PT9-7 010054 . . . . . . . . . . PT9-7 010055 . . . . . . . . . . PT9-7 010056 . . . . . . . . . . PT9-7 010057 . . . . . . . . . . PT9-7 010058 . . . . . . . . . . PT9-7 010059 . . . . . . . . . . PT9-7 010060 . . . . . . . . . . PT9-7 010061 . . . . . . . . . . PT9-7 010075 . . . . . . . . . . PT9-7 010076 . . . . . . . . . . PT9-7 010077 . . . . . . . . . . PT9-7 010078 . . . . . . . . . . PT9-7 010080 . . . . . . . . . . PT9-7 010081 . . . . . . . . . . PT9-7 010084 . . . . . . . . . . PT9-7 010085 . . . . . . . . . . PT9-7 010088 . . . . . . . . . . PT9-7 010089 . . . . . . . . . . PT9-7 010092 . . . . . . . . . . PT9-7 010093 . . . . . . . . . . PT9-7 010096 . . . . . . . . . . PT9-7 010097 . . . . . . . . . . PT9-7 010100 . . . . . . . . . . PT9-7 010104 . . . . . . . . . . PT9-7 010105 . . . . . . . . . . PT9-7 010107 . . . . . . . . . . PT9-7 010110 . . . . . . . . . . PT9-7

Page Part No.

010112 . . . . . . . . . . PT9-7 010114 . . . . . . . . . . PT9-7 010117 . . . . . . . . . . PT9-7 010120 . . . . . . . . . . PT9-7 010123 . . . . . . . . . . PT9-7 010126 . . . . . . . . . . PT9-7 010127 . . . . . . . . . . PT9-7 010128 . . . . . . . . . . PT9-7 010129 . . . . . . . . . . PT9-7 010130 . . . . . . . . . . PT9-7 010131 . . . . . . . . . . PT9-7 010189 . . . . . . . . . PT1-34 010190 . . . . . . . . . PT1-34 010191 . . . . . . . . . PT1-34 010192 . . . . . . . . . PT1-34 010193 . . . . . . . . . PT1-34 010194 . . . . . . . . . PT1-34 010195 . . . . . . . . . PT1-34 010196 . . . . . . . . . PT1-34 010290 . . PT1-37, PT1-39 010291 . . PT1-37, PT1-39 010292 . . PT1-37, PT1-39 010293 . . PT1-37, PT1-39 010294 . . PT1-37, PT1-39 010295 . . PT1-37, PT1-39 010296 . . PT1-37, PT1-39 010297 . . PT1-37, PT1-39 010300 . . . . . . . . . PT1-31 010301 . . . . . . . . PT1-31, . . . . . . . . PT1-38, PT1-40 010302 . . . . . . . . PT1-31, . . . . . . . . PT1-38, PT1-40 010303 . . . . . . . . . PT1-31 010304 . . . . . . . . . PT1-31, . . . . . . . . PT1-38, PT1-40 010305 . . . . . . . . PT1-31, . . . . . . . . PT1-38, PT1-40 010306 . . . . . . . . . PT1-31 010471 . . . . . . . . . PT1-33 010472 . . . . . . . . . PT1-33 010473 . . . . . . . . . PT1-33 010474 . . . . . . . . . PT1-33 010475 . . . . . . . . . PT1-33 010476 . . . . . . . . . PT1-33 010477 . . . . . . . . . PT1-33 010478 . . . . . . . . . PT1-33 010479 . . . . . . . . . PT1-33 010480 . . . . . . . . . PT1-33 010508 . . PT1-38, PT1-40 010509 . . PT1-38, PT1-40 010510 . . . . . . . . . PT1-33 010511 . . . . . . . . . PT1-33 010512 . . . . . . . . . PT1-33 010513 . . . . . . . . . PT1-33 010514 . . . . . . . . . PT1-33 010515 . . . . . . . . . PT1-33 010516 . . . . . . . . . PT1-33 010524 . . . . . . . . . PT1-33 010525 . . . . . . . . . PT1-33 010526 . . . . . . . . . PT1-33 010528 . . PT1-31, PT1-34 010529 . . PT1-31, PT1-34 010530 . PT1-31, PT1-34, . . . . . . . . PT1-38, PT1-40 010531 . . . . . . . . . PT1-31, . . . . . . . . PT1-33, PT1-34, . . . . . . . . PT1-38, PT1-40 010532 . . . . . . . . . PT1-31, . . . . . . . . PT1-33, PT1-34 010533 . . PT1-31, PT1-34 010539 . . . . . . . . . PT1-28

INDEX-3

Page Part No.

010547 . . . . . . . . . PT1-28 010548 . . . . . . . . . PT1-28 010549 . . . . . . . . . PT1-28 010550 . . . . . . . . . PT1-28 010551 . . . . . . . . . PT1-28 010552 . . . . . . . . . PT1-28 010553 . . . . . . . . . PT1-28 010554 . . . . . . . . . PT1-28 010555 . . . . . . . . . PT1-28 010556 . . . . . . . . . PT1-28 010567 . . . . . . . . . PT1-29 010568 . . . . . . . . . PT1-29 010569 . . . . . . . . . PT1-29 010570 . . . . . . . . . PT1-29 010571 . . . . . . . . . PT1-29 010572 . . . . . . . . . PT1-29 010573 . . . . . . . . . PT1-29 010574 . . . . . . . . . PT1-29 010575 . . . . . . . . . PT1-29 010576 . . . . . . . . . PT1-29 010577 . . . . . . . . . PT1-29 010578 . . . . . . . . . PT1-29 010579 . . . . . . . . . PT1-29 010582 . . . . . . . . . PT1-29 010583 . . . . . . . . . PT1-29 010584 . . . . . . . . . PT1-29 010585 . . . . . . . . . PT1-29 010586 . . . . . . . . . PT1-29 010587 . . . . . . . . . PT1-29 010588 . . . . . . . . . PT1-29 010589 . . . . . . . . . PT1-29 010590 . . . . . . . . . PT1-29 010591 . . . . . . . . . PT1-29 010592 . . . . . . . . . PT1-29 010593 . . . . . . . . . PT1-29 010594 . . . . . . . . . PT1-29 010595 . . . . . . . . . PT1-29 010598 . . . . . . . . . PT1-34 010599 . . . . . . . . . PT1-34 010601 . . . . . . . . . PT1-22 010602 . . . . . . . . . PT1-22 010603 . . PT1-22, PT1-37, . . . . . . . . PT1-39, PT3-15 010604 . . PT1-22, PT1-37, . . . . . . . . PT1-39, PT3-15 010605 . . . . . . . . . PT1-22 010606 . . PT1-22, PT1-37, . . . . . . . . PT1-39, PT3-15 010607 . . PT1-22, PT1-37, . . . . . . . . PT1-39, PT3-15 010607 . . . . . . . . . PT3-15 010608 . . . . . . . . . PT1-22 010657 . . . . . . . . . PT1-34 010658 . . . . . . . . . PT1-34 010659 . . . . . . . . . PT1-34 010660 . . . . . . . . . PT1-34 010675 . . . . . . . . . PT1-29 010676 . . . . . . . . . PT1-29 010677 . . . . . . . . . PT1-29 010678 . . . . . . . . . PT1-29 010679 . . . . . . . . . PT1-29 010680 . . . . . . . . . PT1-29 010681 . . . . . . . . . PT1-29 010682 . . . . . . . . . PT1-29 010683 . . . . . . . . . PT1-29 010684 . . . . . . . . . PT1-29 010685 . . . . . . . . . PT1-29 010686 . . . . . . . . . PT1-29 010687 . . . . . . . . . PT1-29 010688 . . . . . . . . . PT1-29 010689 . . . . . . . . . PT1-29

Page

010690 . . . . . . . . . PT1-29 010691 . . . . . . . . PT1-29 010692 . . . . . . . . . PT1-29 010693 . . . . . . . . PT1-29 010694 . . . . . . . . PT1-29 010695 . . . . . . . . PT1-29 010696 . . . . . . . . . PT1-29 010697 . . . . . . . . . PT1-29 010698 . . . . . . . . . PT1-29 010699 . . . . . . . . . PT1-29 010723 . . . . . . . . PT1-28 010975 . . . . . . . . PT1-28 010976 . . . . . . . . PT1-28 010977 . . . . . . . . . PT1-29 010978 . . . . . . . . PT1-29 010979 . . . . . . . . PT1-29 010980 . . . . . . . . PT1-29 010981 . . . . . . . . PT1-29 010982 . . . . . . . . PT1-29 010983 . . . . . . . . PT1-29 010984 . . . . . . . . PT1-29 010985 . . . . . . . . PT1-29 010986 . . . . . . . . . PT1-29 010987 . . . . . . . . . PT1-29 010988 . . . . . . . . PT1-29 010989 . . . . . . . . PT1-29 010990 . . . . . . . . PT1-29 010991 . . . . . . . . PT1-29 010992 . . . . . . . . . PT1-29 010993 . . . . . . . . . PT1-29 010994 . . . . . . . . PT1-29 010995 . . . . . . . . . PT1-29 010996 . . . . . . . . PT1-29 010997 . . . . . . . . PT1-29 010998 . . . . . . . . PT1-29 011000 . . . . . . . . PT1-29 011001 . . . . . . . . PT1-29 011002 . . . . . . . . PT1-29 011005 . . . . . . . . PT1-29 011006 . . . . . . . . PT1-29 011012 . . . . . . . . PT1-29 011105 . . PT1-22, PT1-67 011106 . . . . . . . . PT1-22, . . . . . . . PT1-31, PT1-33, . . . . . . . . PT1-34, PT1-67 011107 . . . . . . . . PT1-22, . . . . . . . .PT1-31, PT1-33, . . . . . . . . PT1-34, PT1-67 011108 . . . . . . . . PT1-22, . . . . . . . .PT1-31, PT1-33, . . . . . . . . PT1-34, PT1-67 011109 . . . . . . . . PT1-22, . . . . . . . .PT1-31, PT1-33, . . . . . . . . PT1-34, PT1-67 011110 . . . . . . . . PT1-22, . . . . . . . PT1-31, PT1-33, . . . . . . . . PT1-34, PT1-67 011111 . . . . . . . . PT1-22, . . . . . . . .PT1-31, PT1-33, . . . . . . . . PT1-34, PT1-67 011112 . . . . . . . . PT1-22, . . . . . . . .PT1-31, PT1-33, . . . . . . . . PT1-34, PT1-67 011113 . . . . . . . . . PT1-29 011114 . . . . . . . . PT1-22, . . . . . . . PT1-31, PT1-33, . . . . . . . . PT1-34, PT1-67 011115 . . . . . . . . . PT1-29 011117 . . . . . . . . PT1-22, . . . . . . . PT1-31, PT1-33, . . . . . . . . PT1-34, PT1-67

INDEX

TN


TN INDEX

Part No.

E

Page Part No.

011119 . . . . . . . . . PT1-29 011120 . . . . . . . . .PT1-22, . . . . . . . . PT1-31, PT1-33, . . . . . . . . PT1-34, PT1-67 011121 . . . . . . . . . PT1-28 011124 . . . . . . . . PT1-22, . . . . . . . . PT1-31, PT1-33, . . . . . . . . PT1-34, PT1-67 011125 . . . . . . . . . PT1-28 011132 . . . . . . . . . PT1-28 011134 . . . . . . . . PT1-22, . . . . . . . . PT1-37, PT1-39 011137 . . . . . . . . .PT1-22, . . . . . . . . PT1-37, PT1-39 011140 . . . . . . . . . PT1-22 011144 . . . . . . . . . PT1-22 011145 . . . . . . . . . PT1-28 011152 . . . . . . . . . PT1-28 011154 . . . . . . . . .PT1-22, . . . . . . . . PT1-37, PT1-39 011157 . . . . . . . . PT1-22, . . . . . . . . PT1-37, PT1-39 011160 . . . . . . . . . PT1-22 011164 . . . . . . . . . PT1-22 011227 . . . . . . . . PT1-37, . . . . . . . PT1-38, PT1-39, . . . . . . . . PT1-40, PT1-67 011228 . . . . . . . . .PT1-37, . . . . . . . PT1-38, PT1-39, . . . . . . . . PT1-40, PT1-67 011230 . . . . . . . . .PT1-37, . . . . . . . PT1-38, PT1-39, . . . . . . . . PT1-40, PT1-67 011231 . . . . . . . . PT1-37, . . . . . . . PT1-38, PT1-39, . . . . . . . . PT1-40, PT1-67 011234 . . . . . . . . .PT1-37, . . . . . . . PT1-38, PT1-39, . . . . . . . . PT1-40, PT1-67 011236 . . . . . . . . PT1-37, . . . . . . . . PT1-38, PT1-39, . . . . . . . . PT1-40, PT1-67 011239 . . . . . . . . .PT1-37, . . . . . . . PT1-38, PT1-39, . . . . . . . . PT1-40, PT1-67 011242 . . . . . . . . .PT1-37, . . . . . . . PT1-38, PT1-39, . . . . . . . . PT1-40, PT1-67 011247 . . PT1-39, PT1-40 011248 . . PT1-39, PT1-40 011250 . . PT1-39, PT1-40 011251 . . PT1-39, PT1-40 011254 . . PT1-39, PT1-40 011256 . . PT1-39, PT1-40 011259 . . PT1-39, PT1-40 011262 . . PT1-39, PT1-40 011266 . . . . . . . . . PT1-67 011267 . . . . . . . . . PT1-67 011268 . . . . . . . . . PT1-67 011269 . . . . . . . . . PT1-67 011271 . . . . . . . . . PT1-67 011272 . . . . . . . . . PT1-67 011273 . . . . . . . . . PT1-67 011280 . . . . . . . . . PT1-67 011285 . . . . . . . . . PT1-67 011286 . . . . . . . . . PT1-67 011287 . . . . . . . . . PT1-67 011288 . . . . . . . . . PT1-67 011289 . . . . . . . . . PT1-67 011290 . . . . . . . . . PT1-67 011292 . . . . . . . . . PT1-67

N E Page Part No.

011296 . . . . . . . . . PT1-67 011297 . . . . . . . . . PT1-67 011298 . . . . . . . . . PT1-67 011299 . . . . . . . . . PT1-67 011300 . . . . . . . . . PT1-67 011301 . . . . . . . . . PT1-67 011302 . . . . . . . . . PT1-67 011303 . . . . . . . . . PT1-67 011304 . . . . . . . . . PT1-67 011305 . . . . . . . . . PT1-67 011306 . . . . . . . . . PT1-67 011307 . . PT1-37, PT1-38 011308 . . PT1-37, PT1-38 011310 . . PT1-37, PT1-38 011311 . . PT1-37, PT1-38 011312 . . . . . . . . . PT1-67 011313 . . . . . . . . . PT1-67 011314 . . PT1-37, PT1-38 011315 . . . . . . . . . PT1-67 011316 . . PT1-37, PT1-38 011319 . . PT1-37, PT1-38 011322 . . PT1-37, PT1-38 011455 . . . . . . . . . PT1-22 011456 . . . . . . . . . PT1-22 011457 . . . . . . . . PT1-22, . . . . . . . PT1-31, PT1-33, . . . . . . . . PT1-34, PT1-67 011463 . .PT1-22, PT1-31, . . . . . . . . PT1-34, PT1-67 011471 . . . . . . . . . PT1-22 011472 . . . . . . . . . PT1-22 011529 . . PT1-22, PT1-67 011555 . . . . . . . . . PT1-28 011564 . . . . . . . . . PT1-28 011565 . . . . . . . . . PT1-28 011567 . . . . . . . . . PT1-28 011569 . . . . . . . . . PT1-28 011571 . . . . . . . . . PT1-28 011579 . . . . . . . . . PT1-28 011580 . . . . . . . . . PT1-28 011581 . . . . . . . . . PT1-28 011582 . . . . . . . . . PT1-28 011583 . . . . . . . . . PT1-28 011584 . . . . . . . . . PT1-28 011586 . . . . . . . . . PT1-28 011587 . . . . . . . . . PT1-28 011589 . . . . . . . . . PT1-28 011602 . . . . . . . . . PT1-28 011603 . . . . . . . . . PT1-28 011604 . . . . . . . . . PT1-28 011605 . . . . . . . . . PT1-29 011606 . . . . . . . . . PT1-28 011607 . . . . . . . . . PT1-29 011620 . . . . . . . . . PT1-27 011621 . . . . . . . . . PT1-27 011622 . . . . . . . . . PT1-27 011623 . . . . . . . . . PT1-27 011624 . . . . . . . . . PT1-27 011625 . . . . . . . . . PT1-27 011626 . . . . . . . . . PT1-27 011627 . . . . . . . . . PT1-27 011628 . . . . . . . . . PT1-27 011700 . . . . . . . . . PT1-28 011701 . . . . . . . . . PT1-28 011702 . . . . . . . . . PT1-28 011703 . . . . . . . . . PT1-29 011705 . . . . . . . . . PT1-28 011706 . . . . . . . . . PT1-28 011707 . . . . . . . . . PT1-28 011708 . . . . . . . . . PT1-29 011709 . . . . . . . . . PT1-29

Page Part No.

011710. . . . . . . . . PT1-28 011711 . . . . . . . . . PT1-28 011712. . . . . . . . . PT1-29 011713 . . . . . . . . . PT1-29 011714 . . . . . . . . . PT1-34 011715 . . . . . . . . . PT1-34 011716 . . . . . . . . . PT1-34 011717 . . . . . . . . . PT1-34 011718 . . . . . . . . . PT1-34 011719 . . . . . . . . . PT1-34 011720 . . . . . . . . . PT1-28 011721 . . . . . . . . . PT1-28 011722 . . . . . . . . . PT1-28 011723 . . . . . . . . . PT1-28 011724 . . . . . . . . . PT1-28 011725 . . . . . . . . . PT1-28 011726 . . . . . . . . . PT1-28 011727 . . . . . . . . . PT1-28 011728 . . . . . . . . . PT1-28 011729 . . . . . . . . . PT1-28 011730 . . . . . . . . . PT1-28 011731 . . . . . . . . . PT1-28 011732 . . . . . . . . . PT1-28 011733 . . . . . . . . . PT1-28 011734 . . . . . . . . . PT1-28 011740 . . . . . . . . . PT1-28 011741 . . . . . . . . . PT1-28 011742 . . . . . . . . . PT1-28 011743 . . . . . . . . . PT1-28 011744 . . . . . . . . . PT1-28 011745 . . . . . . . . . PT1-28 011746 . . . . . . . . . PT1-28 011747 . . . . . . . . . PT1-28 011748 . . . . . . . . . PT1-28 011749 . . . . . . . . . PT1-28 011750 . . . . . . . . . PT1-28 011751 . . . . . . . . . PT1-28 011752 . . . . . . . . . PT1-28 011753 . . . . . . . . . PT1-28 011754 . . . . . . . . . PT1-28 011755 . . . . . . . . . PT1-28 011756 . . . . . . . . . PT1-28 011757 . . . . . . . . . PT1-28 011758 . . . . . . . . . PT1-28 011759 . . . . . . . . . PT1-28 011760 . . . . . . . . . PT1-28 011761 . . . . . . . . . PT1-28 011762 . . . . . . . . . PT1-28 011763 . . . . . . . . . PT1-28 011764 . . . . . . . . . PT1-28 011765 . . . . . . . . . PT1-28 011766 . . . . . . . . . PT1-28 011767 . . . . . . . . . PT1-28 011768 . . . . . . . . . PT1-28 011775 . . . . . . . . . PT1-28 011776 . . . . . . . . . PT1-28 011777 . . . . . . . . . PT1-28 011778 . . . . . . . . . PT1-28 011779 . . . . . . . . . PT1-28 011780 . . . . . . . . . PT1-28 011781 . . . . . . . . . PT1-28 011782 . . . . . . . . . PT1-28 011783 . . . . . . . . . PT1-28 011784 . . . . . . . . . PT1-28 011785 . . . . . . . . . PT1-28 011786 . . . . . . . . . PT1-28 011787 . . . . . . . . . PT1-28 011788 . . . . . . . . . PT1-28 011789 . . . . . . . . . PT1-28 011790 . . . . . . . . . PT1-28 011791 . . . . . . . . . PT1-28

Page Part No.

011792 . . . . . . . . . PT1-28 011793 . . . . . . . . . PT1-28 011794 . . . . . . . . . PT1-28 011795 . . . . . . . . . PT1-28 011796 . . . . . . . . . PT1-28 011797 . . . . . . . . . PT1-28 011798 . . . . . . . . . PT1-28 011799 . . . . . . . . . PT1-28 011800 . . . . . . . . . PT1-28 011801 . . . . . . . . . PT1-28 011802 . . . . . . . . . PT1-28 011803 . . . . . . . . . PT1-28 011804 . . . . . . . . . PT1-28 011805 . . . . . . . . . PT1-28 011806 . . . . . . . . . PT1-28 011807 . . . . . . . . . PT1-28 011810 . . . . . . . . . PT1-28 011811 . . . . . . . . . PT1-28 011812 . . . . . . . . . PT1-28 011813 . . . . . . . . . PT1-28 011814 . . . . . . . . . PT1-28 011815 . . . . . . . . . PT1-28 011816 . . . . . . . . . PT1-28 011817 . . . . . . . . . PT1-28 011818 . . . . . . . . . PT1-28 011819 . . . . . . . . . PT1-28 011820 . . . . . . . . . PT1-28 011821 . . . . . . . . . PT1-28 011822 . . . . . . . . . PT1-28 011823 . . . . . . . . . PT1-28 011824 . . . . . . . . . PT1-28 011825 . . . . . . . . . PT1-28 011826 . . . . . . . . . PT1-28 011827 . . . . . . . . . PT1-28 011828 . . . . . . . . .PT1-28 011829 . . . . . . . . .PT1-28 011830 . . . . . . . . .PT1-28 011831 . . . . . . . . .PT1-28 011832 . . . . . . . . .PT1-28 011833 . . . . . . . . .PT1-28 011834 . . . . . . . . .PT1-28 011835 . . . . . . . . .PT1-28 011836 . . . . . . . . .PT1-28 011837 . . . . . . . . .PT1-28 011838 . . . . . . . . .PT1-28 011839 . . . . . . . . .PT1-29 011840 . . . . . . . . .PT1-29 011841 . . . . . . . . .PT1-29 011842 . . . . . . . . .PT1-29 011847 . . . . . . . . .PT1-28 011850 . . . . . . . . .PT1-28 011851 . . . . . . . . .PT1-28 011852 . . . . . . . . .PT1-28 011853 . . . . . . . . .PT1-28 011854 . . . . . . . . .PT1-28 011855 . . . . . . . . .PT1-28 011856 . . . . . . . . .PT1-28 011857 . . . . . . . . .PT1-28 011858 . . . . . . . . .PT1-28 011859 . . . . . . . . .PT1-28 011860 . . . . . . . . .PT1-28 011861 . . . . . . . . .PT1-28 011862 . . . . . . . . .PT1-28 011863 . . . . . . . . .PT1-28 011864 . . . . . . . . .PT1-28 011865 . . . . . . . . .PT1-28 011866 . . . . . . . . .PT1-28 011867 . . . . . . . . .PT1-28 011868 . . . . . . . . .PT1-28 011869 . . . . . . . . .PT1-28 011870 . . . . . . . . .PT1-28

INDEX-4

011871 . . . . . . . . . 011872 . . . . . . . . 011873 . . . . . . . . . 011874 . . . . . . . . . 011875 . . . . . . . . . 011876 . . . . . . . . . 011877 . . . . . . . . . 011878 . . . . . . . . . 011879 . . . . . . . . . 011880 . . . . . . . . . 011890 . . . . . . . . . 011891 . . . . . . . . . 011892 . . . . . . . . . 011893 . . . . . . . . . 011894 . . . . . . . . . 011895 . . . . . . . . . 011896 . . . . . . . . . 011897 . . . . . . . . . 011898 . . . . . . . . . 011899 . . . . . . . . . 011900 . . . . . . . . . 011901 . . . . . . . . . 011902 . . . . . . . . . 011903 . . . . . . . . . 011904 . . . . . . . . . 011905 . . . . . . . . . 011906 . . . . . . . . . 011907 . . . . . . . . . 011908 . . . . . . . . . 011909 . . . . . . . . . 011910 . . . . . . . . . 011911 . . . . . . . . . 011912 . . . . . . . . . 011913 . . . . . . . . . 011914 . . . . . . . . . 011915 . . . . . . . . . 011916 . . . . . . . . . 011917 . . . . . . . . . 011918 . . . . . . . . . 011919 . . . . . . . . . 011920 . . . . . . . . . 011921 . . . . . . . . . 011922 . . . . . . . . . 011923 . . . . . . . . . 011924 . . . . . . . . . 011925 . . . . . . . . 011926 . . . . . . . . 011927 . . . . . . . . 011928 . . . . . . . . 011929 . . . . . . . . 011930 . . . . . . . . 011935 . . . . . . . . 011936 . . . . . . . . 011937 . . . . . . . . 011938 . . . . . . . . 011939 . . . . . . . . 011940 . . . . . . . . 011941 . . . . . . . . . 011942 . . . . . . . . 011943 . . . . . . . . 011944 . . . . . . . . 011945 . . . . . . . . 011946 . . . . . . . . 011947 . . . . . . . . 011948 . . . . . . . . 011949 . . . . . . . . . 011950 . . . . . . . . . 011951 . . . . . . . . . 011952 . . . . . . . . . 011953 . . . . . . . . . 011954 . . . . . . . . .

Page Part No. PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-29 PT1-29 PT1-29 PT1-29 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-29 PT1-29 PT1-29 PT1-29 PT1-29 PT1-29 PT1-29 PT1-29 PT1-29 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28 PT1-28

011955 . . . . . . . . . 011956 . . . . . . . . . 011957 . . . . . . . . . 011958 . . . . . . . . . 011959 . . . . . . . . . 011960 . . . . . . . . . 011961 . . . . . . . . . 011962 . . . . . . . . . 011963 . . . . . . . . . 011964 . . . . . . . . . 011965 . . . . . . . . . 011966 . . . . . . . . . 011967 . . . . . . . . . 012023 . . . . . . . . . 012024 . . . . . . . . . 012025 . . . . . . . . . 012026 . . . . . . . . . 012027 . . . . . . . . . 012028 . . . . . . . . . 012029 . . . . . . . . . 012289 . . . . . . . . . 012290 . . . . . . . . . 012291 . . . . . . . . . 012455 . . . . . . . . . 012456 . . . . . . . . . 012765 . . . . . . . . . 012766 . . . . . . . . . 012767 . . . . . . . . . 013040 . . . . . . . . . 013041 . . . . . . . . . 013042 . . . . . . . . . 013043 . . . . . . . . . 013044 . . . . . . . . . 013045 . . . . . . . . . 013046 . . . . . . . . . 013047 . . . . . . . . . 013048 . . . . . . . . . 013049 . . . . . . . . . 013095 . . . . . . . . . 013096 . . . . . . . . . 013110 . . . . . . . . . 013111 . . . . . . . . . 013112 . . . . . . . . . 013113 . . . . . . . . . 013114 . . . . . . . . . 013115 . . . . . . . . . 013116 . . . . . . . . . 013117 . . . . . . . . . 013118 . . . . . . . . . 013119 . . . . . . . . . 013120 . . . . . . . . . 013121 . . . . . . . . . 013122 . . . . . . . . . 013123 . . . . . . . . . 013124 . . . . . . . . . 013125 . . . . . . . . . 013126 . . . . . . . . . 013127 . . . . . . . . . 013128 . . . . . . . . . 013129 . . . . . . . . . 013130 . . . . . . . . . 013131 . . . . . . . . . 013132 . . . . . . . . . 013133 . . . . . . . . . 013134 . . . . . . . . . 013135 . . . . . . . . . 013136 . . . . . . . . . 013137 . . . . . . . . . 013138 . . . . . . . . . 013139 . . . . . . . . . 013140 . . . . . . . . .

Page PT1-28 PT1-28 PT1-28 PT1-28 PT1-29 PT1-29 PT1-29 PT1-29 PT1-29 PT1-29 PT1-29 PT1-29 PT1-29 PT1-29 PT1-29 PT1-29 PT1-29 PT1-29 PT1-29 PT1-29 PT1-28 PT1-28 PT1-28 PT1-67 PT1-67 PT1-28 PT1-28 PT1-28 PT1-23 PT1-23 PT1-23 PT1-23 PT1-23 PT1-23 PT1-23 PT1-23 PT1-23 PT1-23 PT1-23 PT1-23 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56 PT1-56


Part No.

E

Page Part No.

013141. . . . . . . . . PT1-56 013142 . . . . . . . . . PT1-56 013143. . . . . . . . . PT1-56 013144. . . . . . . . . PT1-56 013145. . . . . . . . . PT1-56 013146. . . . . . . . . PT1-56 013147. . . . . . . . . PT1-56 013148. . . . . . . . . PT1-56 013149. . . . . . . . . PT1-56 013150. . . . . . . . . PT1-56 013151. . . . . . . . . PT1-56 013152. . . . . . . . . PT1-56 013154. . . . . . . . . PT1-56 013155. . . . . . . . . PT1-56 013156. . . . . . . . . PT1-56 013157. . . . . . . . . PT1-56 019164. . . . . . . . . . PT4-8 019165. . . . . . . . . . PT4-8 021990. . . . . . . . . . PT1-7 021992. . . . . . . . . . PT1-7 021993. . . . . . . . . . PT1-7 021994. . . . . . . . . . PT1-7 021997. . . . . . . . . PT1-13 021998. . . . . . . . . PT1-13 022000. . . . . . . . . PT1-13 022004. . . . . . . . . PT1-13 022006. . . . . . . . . PT1-13 022007. . . . . . . . . PT1-13 022009. . . . . . . . . PT1-13 022010. . . . . . . . . PT1-13 022011. . . . . . . . . PT1-13 022012. . . . . . . . . PT1-13 022014. . . . . . . . . PT1-13 022015. . . . . . . . . PT1-13 022017. . . . . . . . . PT1-13 022183. . . . . . . . . . PT1-7 022184. . . . . . . . . . PT1-7 022185. . . . . . . . . . PT1-7 022187. . . . . . . . . . PT1-7 022188. . . . . . . . . . PT1-7 022189. . . . . . . . . . PT1-7 022190. . . . . . . . . . PT1-7 022191. . . . . . . . . . PT1-7 022192. . . . . . . . . . PT1-7 022193. . . . . . . . . . PT1-7 022194. . . . . . . . . . PT1-7 022196. . . . . . . . . . PT1-7 022197. . . . . . . . . . PT1-7 022198. . . . . . . . . . PT1-7 022211. . . . . . . . . . PT1-7 022212. . . . . . . . . . PT1-7 022213. . . . . . . . . . PT1-7 022214. . . . . . . . . . PT1-7 022216. . . . . . . . . . PT1-7 022217. . . . . . . . . . PT1-7 022219. . . . . . . . . . PT1-7 022220. . . . . . . . . PT1-13 022221. . . . . . . . . PT1-13 022222. . . . . . . . . PT1-13 022232. . . . . . . . . . PT1-7 022234. . . . . . . . . . PT1-7 022235. . . . . . . . . . PT1-7 022236. . . . . . . . . . PT1-7 022237. . . . . . . . . . PT1-7 022238. . . . . . . . . . PT1-7 022329. . . . . . . . . PT1-13 022331. . . . . . . . . PT1-13 022332. . . . . . . . . PT1-13 022335. . . . . . . . . PT1-13 022336. . . . . . . . . PT1-13 022337. . . . . . . . . PT1-13

N E Page Part No.

022339 . . . . . . . . . PT1-13 022340 . . . . . . . . . PT1-13 022341 . . . . . . . . .PT1-13 022342 . . . . . . . . .PT1-13 022344 . . . . . . . . .PT1-13 022345 . . . . . . . . .PT1-13 022346 . . . . . . . . .PT1-13 022349 . . . . . . . . .PT1-13 022351 . . . . . . . . .PT1-13 022352 . . . . . . . . .PT1-13 022353 . . . . . . . . .PT1-13 022354 . . . . . . . . .PT1-13 022355 . . . . . . . . .PT1-13 022357 . . . . . . . . .PT1-13 022358 . . . . . . . . .PT1-13 022359 . . . . . . . . .PT1-13 022362 . . . . . . . . .PT1-13 022363 . . . . . . . . .PT1-13 022364 . . . . . . . . .PT1-13 022365 . . . . . . . . .PT1-13 022368 . . . . . . . . .PT1-13 022370 . . . . . . . . .PT1-13 022371 . . . . . . . . .PT1-13 022372 . . . . . . . . .PT1-13 022374 . . . . . . . . .PT1-13 022375 . . . . . . . . .PT1-13 022376 . . . . . . . . .PT1-13 022377 . . . . . . . . .PT1-13 022378 . . . . . . . . .PT1-13 022379 . . . . . . . . .PT1-13 022380 . . . . . . . . .PT1-13 022381 . . . . . . . . .PT1-13 022382 . . . . . . . . .PT1-13 022384 . . . . . . . . .PT1-13 022386 . . . . . . . . .PT1-13 022387 . . . . . . . . .PT1-13 022388 . . . . . . . . . PT1-13 022389 . . . . . . . . . PT1-13 022391 . . . . . . . . . PT1-13 022392 . . . . . . . . . PT1-13 022393 . . . . . . . . . PT1-13 022394 . . . . . . . . . PT1-13 022395 . . . . . . . . . PT1-13 022396 . . . . . . . . . PT1-13 022397 . . . . . . . . . PT1-13 022398 . . . . . . . . . PT1-13 022399 . . . . . . . . . PT1-13 022400 . . . . . . . . . PT1-13 022402 . . . . . . . . . PT1-13 022404 . . . . . . . . . PT1-13 022405 . . . . . . . . . PT1-13 022406 . . . . . . . . . PT1-13 022408 . . . . . . . . . PT1-13 022409 . . . . . . . . . PT1-13 022410 . . . . . . . . . PT1-13 022411 . . . . . . . . . PT1-13 022412 . . . . . . . . . PT1-13 022413 . . . . . . . . . PT1-13 022414 . . . . . . . . . PT1-13 022415 . . . . . . . . . PT1-13 022416 . . . . . . . . . PT1-13 022417 . . . . . . . . . PT1-13 022418 . . . . . . . . . PT1-13 022420 . . . . . . . . . PT1-13 022429 . . . . . . . . . PT1-13 022430 . . . . . . . . . PT1-13 022432 . . . . . . . . . PT1-13 022433 . . . . . . . . . PT1-13 022434 . . . . . . . . . PT1-13 022435 . . . . . . . . . PT1-13 022453 . . . . . . . . . PT1-13

Page Part No.

022454 . . . . . . . . PT1-13 022455 . . . . . . . . PT1-13 022457 . . . . . . . . . PT1-13 022458 . . . . . . . . . PT1-13 022459 . . . . . . . . . PT1-13 022460 . . . . . . . . . PT1-13 022461 . . . . . . . . . PT1-13 022462 . . . . . . . . . PT1-13 022464 . . . . . . . . PT1-13 022467 . . . . . . . . . PT1-13 022468 . . . . . . . . . PT1-13 022470 . . . . . . . . PT1-13 022471 . . . . . . . . PT1-13 022472 . . . . . . . . . PT1-13 022473 . . . . . . . . . PT1-13 022475 . . . . . . . . . PT1-13 022476 . . . . . . . . . PT1-13 022478 . . . . . . . . . PT1-13 022480 . . . . . . . . . PT1-13 022482 . . . . . . . . . PT1-13 022483 . . . . . . . . . PT1-13 022484 . . . . . . . . . PT1-13 022485 . . . . . . . . . PT1-13 022487 . . . . . . . . PT1-13 022488 . . . . . . . . PT1-13 022489 . . . . . . . . PT1-13 022490 . . . . . . . . PT1-13 022491 . . . . . . . . PT1-13 022492 . . . . . . . . PT1-13 022493 . . . . . . . . PT1-13 022494 . . . . . . . . PT1-13 022496 . . . . . . . . PT1-13 022497 . . . . . . . . PT1-13 022498 . . . . . . . . PT1-13 022500 . . . . . . . . PT1-13 022502 . . . . . . . . . PT1-9 022504 . . . . . . . . . PT1-9 022508 . . . . . . . . . PT1-9 022509 . . . . . . . . . PT1-9 022510 . . . . . . . . . PT1-9 022700 . . . . . . . . . PT1-8 022703 . . . . . . . . . PT1-8 022704 . . . . . . . . . PT1-8 022709 . . . . . . . . . PT1-8 022712 . . . . . . . . . PT1-8 022713 . . . . . . . . . PT1-8 022714 . . . . . . . . . PT1-8 022715 . . . . . . . . . PT1-8 022716 . . . . . . . . . PT1-8 022721 . . . . . . . . . PT1-8 022722 . . . . . . . . . PT1-8 022727 . . . . . . . . . PT1-8 022728 . . . . . . . . . PT1-8 022776 . . . . . . . . PT1-13 022777 . . . . . . . . PT1-13 022780 . . . . . . . . PT1-13 022781 . . . . . . . . PT1-13 022782 . . . . . . . . PT1-13 022783 . . . . . . . . PT1-13 022784 . . . . . . . . PT1-13 022785 . . . . . . . . PT1-13 022786 . . . . . . . . PT1-13 022787 . . . . . . . . PT1-13 022788 . . . . . . . . PT1-13 022810 . . . . . . . . PT1-13 022811 . . . . . . . . PT1-13 022812 . . . . . . . . PT1-13 022813 . . . . . . . . PT1-13 022814 . . . . . . . . PT1-13 022816 . . . . . . . . PT1-13 022817 . . . . . . . . PT1-13

022818 . . . . . . . . . 024000 . . . . . . . . . 024001 . . . . . . . . . 024002 . . . . . . . . . 024003 . . . . . . . . . 024100 . . . . . . . . . 024101 . . . . . . . . . 024102 . . . . . . . . . 024103 . . . . . . . . . 024200 . . . . . . . . . 024201 . . . . . . . . . 024202 . . . . . . . . . 024203 . . . . . . . . . 024300 . . . . . . . . . 024301 . . . . . . . . . 024302 . . . . . . . . . 024303 . . . . . . . . . 024400 . . . . . . . . . 024401 . . . . . . . . . 024402 . . . . . . . . . 024403 . . . . . . . . . 024500 . . . . . . . . . 024501 . . . . . . . . . 024502 . . . . . . . . . 024503 . . . . . . . . . 024600 . . . . . . . . . 024602 . . . . . . . . . 024700 . . . . . . . . . 024701 . . . . . . . . . 024702 . . . . . . . . . 024703 . . . . . . . . . 024800 . . . . . . . . . 024801 . . . . . . . . . 024802 . . . . . . . . . 024803 . . . . . . . . . 024804 . . . . . . . . . 024805 . . . . . . . . . 024900 . . . . . . . . . 024901 . . . . . . . . . 024902 . . . . . . . . . 024903 . . . . . . . . . 025100 . . . . . . . . . 025101 . . . . . . . . . 025102 . . . . . . . . . 025103 . . . . . . . . . 025200 . . . . . . . . . 025201 . . . . . . . . . 025202 . . . . . . . . . 025203 . . . . . . . . . 025300 . . . . . . . . . 025301 . . . . . . . . . 025302 . . . . . . . . . 025303 . . . . . . . . . 025400 . . . . . . . . . 025401 . . . . . . . . . 025402 . . . . . . . . . 025403 . . . . . . . . . 025500 . . . . . . . . . 025501 . . . . . . . . . 025502 . . . . . . . . . 025503 . . . . . . . . . 025600 . . . . . . . . . 025601 . . . . . . . . . 025602 . . . . . . . . . 025603 . . . . . . . . . 025700 . . . . . . . . . 025701 . . . . . . . . . 025702 . . . . . . . . . 025703 . . . . . . . . . 025800 . . . . . . . . . 025801 . . . . . . . . .

INDEX-5

Page Part No. PT1-13 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-31 PT2-32 PT2-32 PT2-32 PT2-32 PT2-32 PT2-32 PT2-32 PT2-32 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34 PT2-34

025802 025803 025900 025901 025902 025903 026000 026001 026002 026003 026004 026005 026006 026007 026100 026101 026102 026103 026104 026105 026200 026201 026202 026203 026204 026205 026300 026301 026302 026303 026304 026305 026400 026401 026402 026403 026404 026405 026500 026501 026502 026503 026504 026505 026600 026601 026602 026603 026604 026605 026800 026801 026802 026803 026804 026805 027023 027024 027025 027026 027027 027028 027029 027030 027031 027032 027033 027034 027035 027036 027037

Page Part No.

. . . . . . . . . PT2-34 . . . . . . . . . PT2-34 . . . . . . . . . PT2-34 . . . . . . . . . PT2-34 . . . . . . . . . PT2-34 . . . . . . . . . PT2-34 . . . . . . . . . PT2-34 . . . . . . . . . PT2-34 . . . . . . . . . PT2-34 . . . . . . . . . PT2-34 . . . . . . . . . PT2-34 . . . . . . . . . PT2-34 . . . . . . . . . PT2-34 . . . . . . . . . PT2-34 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . PT2-35 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7

027038 027039 027040 027041 027042 027043 027044 027045 027046 027047 027048 027049 027050 027051 027052 027053 027054 027055 027056 027057 027058 027059 027060 027061 027062 027063 027064 027065 027066 027067 027068 027069 027070 027071 027072 027073 027074 027075 027076 027077 027078 027079 027080 027081 027082 027083 027084 027085 027500 027501 027502 027503 027506 027507 027550 027551 027552 027553 027556 027557 027600 027601 027602 027603 027604 027605 027609 027610 027611 027650 027651

Page

. . . . . . . . . PT2-7 . . . . . . . . . PT2-7 . . . . . . . . . PT2-7 . . . . . . . . . PT2-7 . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . . PT2-7 . . . . . . . . . PT2-22 . . . . . . . . . PT2-22 . . . . . . . . . PT2-22 . . . . . . . . . PT2-22 . . . . . . . . . PT2-22 . . . . . . . . . PT2-22 . . . . . . . . . PT2-23 . . . . . . . . . PT2-23 . . . . . . . . . PT2-23 . . . . . . . . . PT2-23 . . . . . . . . . PT2-23 . . . . . . . . . PT2-23 . . . . . . . . . PT2-22 . . . . . . . . . PT2-22 . . . . . . . . . PT2-22 . . . . . . . . . PT2-22 . . . . . . . . . PT2-22 . . . . . . . . . PT2-22 . . . . . . . . . PT2-22 . . . . . . . . . PT2-22 . . . . . . . . . PT2-22 . . . . . . . . . PT2-23 . . . . . . . . . PT2-23

INDEX

TN


TN

E

INDEX

Part No.

Page Part No.

027653 027700 027701 027702 027703 027704 027705 027706 027707 027712 027713 027714 027715 027750 027751 027753 027800 027801 027802 027803 027804 027805 027806 027807 027812 027813 027814 027815 027850 027851 028120 028121 028123 028125 028126 028128 028130 028131 028133 028140 028141 028143 028180 028220 028221 028223 028225 028226 028228 028230 028231 028233 028240 028241 028243 028280 028320 028321 028323 028325 028326 028328 028330 028331 028333 028340 028341 028343 028380 028761 028763

PT2-23 PT2-22 PT2-22 PT2-22 PT2-22 PT2-22 PT2-22 PT2-22 PT2-22 PT2-22 PT2-22 PT2-22 PT2-22 PT2-23 PT2-23 PT2-23 PT2-22 PT2-22 PT2-22 PT2-22 PT2-22 PT2-22 PT2-22 PT2-22 PT2-22 PT2-22 PT2-22 PT2-22 PT2-23 PT2-23 PT2-17 PT2-17 PT2-17 PT2-17 PT2-17 PT2-17 PT2-18 PT2-18 PT2-18 PT2-18 PT2-18 PT2-18 PT2-18 PT2-17 PT2-17 PT2-17 PT2-17 PT2-17 PT2-17 PT2-18 PT2-18 PT2-18 PT2-18 PT2-18 PT2-18 PT2-18 PT2-17 PT2-17 PT2-17 PT2-17 PT2-17 PT2-17 PT2-18 PT2-18 PT2-18 PT2-18 PT2-18 PT2-18 PT2-18 PT2-15 PT2-15

......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... ......... .........

028765 028766 028768 028770 028771 028773 028775 028776 028778 028780 028781 028783 028785 028820 028821 028823 028825 028826 028828 028851 028853 028855 028856 028858 028860 028861 028863 028865 028866 028868 028870 028871 028873 028875 028920 028921 028923 028977 028979 028981 029000 029001 029002 029003 029004 029005 029006 029007 029008 029009 029010 029011 029012 029013 029014 029015 029016 029017 029018 029019 029020 029021 029022 029023 029024 029025 029026 029027 029028 029029 029031

N E Page Part No.

. . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-17 . . . . . . . . . PT2-17 . . . . . . . . . PT2-17 . . . . . . . . . PT2-17 . . . . . . . . . PT2-17 . . . . . . . . . PT2-17 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-15 . . . . . . . . . PT2-17 . . . . . . . . . PT2-17 . . . . . . . . . PT2-17 . . . . . . . . . PT2-16 . . . . . . . . . PT2-16 . . . . . . . . . PT2-16 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33 . . . . . . . . . PT2-33

Page Part No.

029032. . . . . . . . . PT2-33 029034 . . . . . . . . . PT2-33 029035. . . . . . . . . PT2-33 029036. . . . . . . . . PT2-33 029037. . . . . . . . . PT2-33 029038. . . . . . . . . PT2-33 029039. . . . . . . . . PT2-33 029040. . . . . . . . . PT2-33 029041. . . . . . . . . PT2-33 029042. . . . . . . . . PT2-33 029043. . . . . . . . . PT2-33 029400. . . . . . . . . PT2-10 029401. . . . . . . . . PT2-10 029402. . . . . . . . . PT2-10 029403. . . . . . . . . PT2-10 029404. . . . . . . . . PT2-10 029405. . . . . . . . . PT2-10 029406. . . . . . . . . PT2-10 029407. . . . . . . . . PT2-10 029408. . . . . . . . . PT2-10 029409. . . . . . . . . PT2-10 029410. . . . . . . . . PT2-10 029411. . . . . . . . . PT2-10 029412. . . . . . . . . PT2-10 029413. . . . . . . . . PT2-10 029414. . . . . . . . . PT2-10 029415. . . . . . . . . PT2-10 029416. . . . . . . . . PT2-10 029417. . . . . . . . . PT2-10 029436. . . . . . . . . . PT2-9 029437. . . . . . . . . . PT2-9 029438. . . . . . . . . . PT2-9 029439. . . . . . . . . . PT2-9 029440. . . . . . . . . . PT2-9 029441. . . . . . . . . . PT2-9 029442. . . . . . . . . . PT2-9 029443. . . . . . . . . . PT2-9 029445. . . . . . . . . . PT2-9 029446. . . . . . . . . . PT2-9 029447. . . . . . . . . . PT2-9 029448. . . . . . . . . . PT2-9 029449. . . . . . . . . . PT2-9 029450. . . . . . . . . . PT2-9 029451. . . . . . . . . . PT2-9 029452. . . . . . . . . . PT2-9 029453. . . . . . . . . . PT2-9 029900. . . . . . . . . PT2-24 029901. . . . . . . . . PT2-24 029902. . . . . . . . . PT2-24 029903. . . . . . . . . PT2-24 029904. . . . . . . . . PT2-24 029905. . . . . . . . . PT2-24 029909. . . . . . . . . PT2-24 029910. . . . . . . . . PT2-24 029911. . . . . . . . . PT2-24 029912. . . . . . . . . PT2-24 029913. . . . . . . . . PT2-24 029914. . . . . . . . . PT2-24 029918. . . . . . . . . PT2-24 029919. . . . . . . . . PT2-24 029920. . . . . . . . . PT2-24 029921. . . . . . . . . PT2-24 029922. . . . . . . . . PT2-24 029923. . . . . . . . . PT2-24 030336. . . . . . . . . PT2-37 030337. . . . . . . . . PT2-38 030381. . . . . . . . . PT2-10 030382. . . . . . . . . PT2-10 030383. . . . . . . . . PT2-10 030384. . . . . . . . . PT2-10 030385. . . . . . . . . PT2-10

Page Part No.

030386 . . . . . . . . .PT2-10 030387 . . . . . . . . .PT2-10 030388 . . . . . . . . . PT2-10 030389 . . . . . . . . . PT2-10 030390 . . . . . . . . . PT2-10 030391 . . . . . . . . . PT2-10 030392 . . . . . . . . . PT2-10 030393 . . . . . . . . . PT2-10 030394 . . . . . . . . . PT2-10 030395 . . . . . . . . . PT2-10 030396 . . . . . . . . . PT2-10 030397 . . . . . . . . . PT2-10 030398 . . . . . . . . . PT2-10 031000 . . . . . . . . . . PT2-6 031001 . . . . . . . . . .PT2-6 031002 . . . . . . . . . . PT2-6 031003 . . . . . . . . . . PT2-6 031004 . . . . . . . . . . PT2-6 031005 . . . . . . . . . . PT2-6 031006 . . . . . . . . . . PT2-6 031007 . . . . . . . . . . PT2-6 031008 . . . . . . . . . . PT2-6 031009 . . . . . . . . . . PT2-6 031010 . . . . . . . . . . PT2-6 031011 . . . . . . . . . . PT2-6 031012 . . . . . . . . . . PT2-6 031013 . . . . . . . . . . PT2-6 031014 . . . . . . . . . . PT2-6 031015 . . . . . . . . . . PT2-6 031016 . . . . . . . . . . PT2-6 031017 . . . . . . . . . . PT2-6 031018 . . . . . . . . . . PT2-6 031019 . . . . . . . . . . PT2-6 031020 . . . . . . . . . . PT2-6 031021 . . . . . . . . . . PT2-6 031022 . . . . . . . . . . PT2-6 031023 . . . . . . . . . . PT2-6 031024 . . . . . . . . . . PT2-6 031025 . . . . . . . . . . PT2-6 031026 . . . . . . . . . . PT2-6 031027 . . . . . . . . . . PT2-6 031028 . . . . . . . . . . PT2-6 031029 . . . . . . . . . . PT2-6 031030 . . . . . . . . . . PT2-6 031031 . . . . . . . . . . PT2-6 031032 . . . . . . . . . . PT2-6 031033 . . . . . . . . . . PT2-6 031034 . . . . . . . . . . PT2-6 031035 . . . . . . . . . . PT2-6 031036 . . . . . . . . . .PT2-6 031037 . . . . . . . . . .PT2-6 031038 . . . . . . . . . .PT2-6 031039 . . . . . . . . . .PT2-6 031040 . . . . . . . . . .PT2-6 031041 . . . . . . . . . .PT2-6 031042 . . . . . . . . . .PT2-6 031043 . . . . . . . . . .PT2-6 031044 . . . . . . . . . .PT2-6 031045 . . . . . . . . . .PT2-6 031046 . . . . . . . . . .PT2-6 031047 . . . . . . . . . .PT2-6 031048 . . . . . . . . . .PT2-6 031049 . . . . . . . . . .PT2-6 031050 . . . . . . . . . .PT2-6 031051 . . . . . . . . . .PT2-6 031052 . . . . . . . . . .PT2-6 031053 . . . . . . . . . .PT2-6 031054 . . . . . . . . . .PT2-6 031055 . . . . . . . . . .PT2-6 031056 . . . . . . . . . .PT2-6 031057 . . . . . . . . . .PT2-6

INDEX-6

031058 . . . . . . . . . 031059 . . . . . . . . . 031060 . . . . . . . . . 031061 . . . . . . . . . 031062 . . . . . . . . . 031063 . . . . . . . . . 031064 . . . . . . . . . 031065 . . . . . . . . . 031066 . . . . . . . . . 031067 . . . . . . . . . 031068 . . . . . . . . . . 031069 . . . . . . . . . . 031070 . . . . . . . . . . 031071 . . . . . . . . . . 031072 . . . . . . . . . . 031073 . . . . . . . . . . 031074 . . . . . . . . . . 031075 . . . . . . . . . . 031076 . . . . . . . . . . 031077 . . . . . . . . . . 031078 . . . . . . . . . . 031079 . . . . . . . . . . 031080 . . . . . . . . . . 031081 . . . . . . . . . . 031082 . . . . . . . . . . 031083 . . . . . . . . . . 031084 . . . . . . . . . . 031085 . . . . . . . . . . 031086 . . . . . . . . . . 031087 . . . . . . . . . . 031088 . . . . . . . . . . 031089 . . . . . . . . . . 031090 . . . . . . . . . . 031091 . . . . . . . . . . 031092 . . . . . . . . . . 031093 . . . . . . . . . . 031094 . . . . . . . . . . 031095 . . . . . . . . . . 031096 . . . . . . . . . . 031097 . . . . . . . . . 031098 . . . . . . . . . . 031099 . . . . . . . . . . 031100 . . . . . . . . . . 031101 . . . . . . . . . . 031102 . . . . . . . . . . 031103 . . . . . . . . . . 031104 . . . . . . . . . . 031105 . . . . . . . . . . 031106 . . . . . . . . . . 031107 . . . . . . . . . . 031108 . . . . . . . . . . 031109 . . . . . . . . . . 031110 . . . . . . . . . . 031111 . . . . . . . . . . 031112 . . . . . . . . . . 031113 . . . . . . . . . . 031114 . . . . . . . . . . 031115 . . . . . . . . . . 031116 . . . . . . . . . . 031117 . . . . . . . . . . 031118 . . . . . . . . . . 031119 . . . . . . . . . . 031120 . . . . . . . . . . 031121 . . . . . . . . . . 031122 . . . . . . . . . . 031123 . . . . . . . . . . 031124 . . . . . . . . . . 031125 . . . . . . . . . . 031126 . . . . . . . . . . 031127 . . . . . . . . . . 031128 . . . . . . . . . .

Page Part No. PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-6 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8 PT2-8

Page

031129 . . . . . . . . . . PT2-8 031130 . . . . . . . . . . PT2-8 031131 . . . . . . . . . . PT2-8 031132 . . . . . . . . . . PT2-8 031133 . . . . . . . . . . PT2-8 031134 . . . . . . . . . . PT2-8 031135 . . . . . . . . . . PT2-8 031136 . . . . . . . . . . PT2-8 031137 . . . . . . . . . . PT2-8 031138 . . . . . . . . . . PT2-8 031139 . . . . . . . . . . PT2-8 031140 . . . . . . . . . . PT2-8 031141 . . . . . . . . . . PT2-8 031142 . . . . . . . . . . PT2-8 031143 . . . . . . . . . . PT2-8 031144 . . . . . . . . . . PT2-8 031145 . . . . . . . . . . PT2-8 031146 . . . . . . . . . . PT2-8 031147 . . . . . . . . . . PT2-8 031148 . . . . . . . . . . PT2-8 031149 . . . . . . . . . . PT2-8 031150 . . . . . . . . . . PT2-8 031151 . . . . . . . . . . PT2-8 031152 . . . . . . . . . . PT2-8 031153 . . . . . . . . . . PT2-8 031154 . . . . . . . . . . PT2-8 031155 . . . . . . . . . . PT2-8 031156 . . . . . . . . . . PT2-8 031157 . . . . . . . . . . PT2-8 031158 . . . . . . . . . . PT2-8 031159 . . . . . . . . . . PT2-8 031160 . . . . . . . . . . PT2-6 031161 . . . . . . . . . . PT2-6 031342 . . . . . . . . . . PT2-8 031343 . . . . . . . . . . PT2-8 031344 . . . . . . . . . . PT2-8 031345 . . . . . . . . . . PT2-8 031346 . . . . . . . . . . PT2-8 031347 . . . . . . . . . . PT2-8 031348 . . . . . . . . . . PT2-8 031349 . . . . . . . . . . PT2-8 031350 . . . . . . . . . . PT2-8 031351 . . . . . . . . . . PT2-6 031353 . . . . . . . . . . PT2-6 031355 . . . . . . . . . . PT2-6 031369 . . . . . . . . . . PT2-8 031371 . . . . . . . . . . PT2-8 031373 . . . . . . . . . . PT2-8 031375 . . . . . . . . . . PT2-8 031377 . . . . . . . . . . PT2-8 031379 . . . . . . . . . . PT2-8 031385 . . . . . . . . . PT2-11 031386 . . . . . . . . . PT2-11 031389 . . . . . . . . . PT2-11 031392 . . . . . . . . . PT2-11 031393 . . . . . . . . . . PT2-6 031395 . . . . . . . . . . PT2-6 031397 . . . . . . . . . . PT2-6 031411 . . . . . . . . . . PT2-8 031413 . . . . . . . . . . PT2-8 031415 . . . . . . . . . . PT2-8 031417 . . . . . . . . . . PT2-8 031419 . . . . . . . . . . PT2-8 031421 . . . . . . . . . . PT2-8 031424 . . . . . . . . . PT2-11 031425 . . . . . . . . . PT2-11 031435 . . . . . . . . . . PT2-6 031437 . . . . . . . . . . PT2-6 031439 . . . . . . . . . . PT2-6 031453 . . . . . . . . . . PT2-8 031455 . . . . . . . . . . PT2-8


Part No.

E

Page Part No.

031457. . . . . . . . . . PT2-8 031459. . . . . . . . . . PT2-8 031461. . . . . . . . . . PT2-8 031463. . . . . . . . . . PT2-8 031477. . . . . . . . . . PT2-6 031479. . . . . . . . . . PT2-6 031481. . . . . . . . . . PT2-6 031495. . . . . . . . . . PT2-8 031497. . . . . . . . . . PT2-8 031499. . . . . . . . . . PT2-8 031507. . . . . . . . . . PT2-6 031509. . . . . . . . . . PT2-6 031511. . . . . . . . . . PT2-6 031525. . . . . . . . . . PT2-8 031527. . . . . . . . . . PT2-8 031529. . . . . . . . . . PT2-8 031537. . . . . . . . . . PT2-6 031539. . . . . . . . . . PT2-6 031541. . . . . . . . . . PT2-6 031555. . . . . . . . . . PT2-8 031557. . . . . . . . . . PT2-8 031559. . . . . . . . . . PT2-8 031716. . . . . . . . . . PT2-9 031718. . . . . . . . . . PT2-9 031910. . . . . . . . . . PT2-9 031911. . . . . . . . . . PT2-9 031913. . . . . . . . . . PT2-9 031914. . . . . . . . . . PT2-9 031915. . . . . . . . . . PT2-9 031916. . . . . . . . . . PT2-9 031917. . . . . . . . . . PT2-9 031918. . . . . . . . . . PT2-9 031919. . . . . . . . . . PT2-9 031920. . . . . . . . . . PT2-9 031921. . . . . . . . . . PT2-9 031922. . . . . . . . . . PT2-9 031923. . . . . . . . . . PT2-9 031924. . . . . . . . . . PT2-9 031925. . . . . . . . . . PT2-9 031926. . . . . . . . . . PT2-9 032400. . . . . . . . . PT2-37 032401. . . . . . . . . PT2-37 032402. . . . . . . . . PT2-38 032408. . PT2-16, PT2-37 032525. . . . . . . . . PT2-11 032531. . . . . . . . . PT2-11 032552. . . . . . . . . PT2-11 040001. . . . . . . . . . PT9-7 040002. . . . . . . . . . PT9-7 040003. . . . . . . . . . PT9-7 040004. . . . . . . . . . PT9-7 040005. . . . . . . . . . PT9-7 040006. . . . . . . . . . PT9-7 040007. . . . . . . . . . PT9-7 040008. . . . . . . . . . PT9-7 040009. . . . . . . . . . PT9-7 040010. . . . . . . . . . PT9-7 040011. . . . . . . . . . PT9-7 040012. . . . . . . . . . PT9-7 040013. . . . . . . . . . PT9-7 040014. . . . . . . . . . PT9-7 040015. . . . . . . . . . PT9-7 040016. . . . . . . . . . PT9-7 040017. . . . . . . . . . PT9-7 040018. . . . . . . . . . PT9-7 040020. . . . . . . . . . PT9-7 040021. . . . . . . . . . PT9-7 040022. . . . . . . . . . PT9-7 040023. . . . . . . . . . PT9-7 040024. . . . . . . . . . PT9-7 040025. . . . . . . . . . PT9-7

N E Page Part No.

040026 . . . . . . . . . .PT9-7 040027 . . . . . . . . . .PT9-7 040028 . . . . . . . . . . PT9-7 040029 . . . . . . . . . . PT9-7 040030 . . . . . . . . . . PT9-7 040031 . . . . . . . . . . PT9-7 040032 . . . . . . . . . . PT9-7 040033 . . . . . . . . . . PT9-7 040034 . . . . . . . . . . PT9-7 051009 . . . . . . . . PT13-33 051016 . . . . . . . . PT13-33 051020 . . . . . . . . PT13-33 051029 . . . . . . . . PT13-33 051033 . . . . . . . . PT13-33 051036 . . . . . . . . PT13-33 051037 . . . . . . . . PT13-33 051040 . . . . . . . . PT13-33 051044 . . . . . . . . PT13-33 051048 . . . . . . . . PT13-33 051059 . . . . . . . . PT13-33 051063 . . . . . . . . PT13-33 051066 . . . . . . . . PT13-33 051070 . . . . . . . . PT13-33 051071 . . . . . . . . PT13-33 051078 . . . . . . . . PT13-33 051082 . . . . . . . . PT13-33 051211 . . . . . . . .PT13-33 051212 . . . . . . . .PT13-33 051215 . . . . . . . .PT13-33 051216 . . . . . . . .PT13-33 051219 . . . . . . . .PT13-33 051223 . . . . . . . .PT13-33 051224 . . . . . . . .PT13-33 051227 . . . . . . . .PT13-33 051231 . . . . . . . .PT13-33 051247 . . . . . . . .PT13-33 051250 . . . . . . . .PT13-33 096008 . . . . . . . . . .PT5-5 096009 . . . . . . . . . .PT5-5 096011 . . . . . . . . . .PT5-5 096014 . . . . . . . . . .PT5-5 096015 . . . . . . . . . .PT5-5 096016 . . . . . . . . . .PT5-5 096018 . . . . . . . . . .PT5-5 096019 . . . . . . . . . .PT5-5 096020 . . . . . . . . . .PT5-5 096021 . . . . . . . . . .PT5-5 096022 . . . . . . . . . .PT5-5 096023 . . . . . . . . . .PT5-5 096028 . . . . . . . . . .PT5-5 096029 . . . . . . . . . .PT5-5 096030 . . . . . . . . . .PT5-5 096031 . . . . . . . . . .PT5-5 096032 . . . . . . . . . .PT5-5 096034 . . . . . . . . . .PT5-5 096035 . . . . . . . . . .PT5-5 096036 . . . . . . . . . .PT5-5 096037 . . . . . . . . . .PT5-5 096038 . . . . . . . . . .PT5-5 096039 . . . . . . . . . .PT5-6 096041 . . . . . . . . . .PT5-6 096042 . . . . . . . . . .PT5-6 096043 . . . . . . . . . .PT5-6 096050 . . . . . . . . . .PT5-6 096051 . . . . . . . . . .PT5-6 096055 . . . . . . . . . .PT5-6 096056 . . . . . . . . . .PT5-6 096057 . . . . . . . . . .PT5-6 096062 . . . . . . . . . .PT5-6 096063 . . . . . . . . . .PT5-6 096064 . . . . . . . . . .PT5-6

Page Part No.

096065 . . . . . . . . . PT5-6 096066 . . . . . . . . . PT5-6 096067 . . . . . . . . . PT5-6 096068 . . . . . . . . . PT5-6 096070 . . . . . . . . . PT5-6 096071 . . . . . . . . . PT5-6 096072 . . . . . . . . . PT5-6 096135 . . . . . . . . . PT5-6 096136 . . . . . . . . . PT5-6 096137 . . . . . . . . . PT5-6 096138 . . . . . . . . . PT5-6 096139 . . . . . . . . . PT5-6 096140 . . . . . . . . . PT5-6 096141 . . . . . . . . . . PT5-6 096142 . . . . . . . . . . PT5-6 096143 . . . . . . . . . . PT5-6 096144 . . . . . . . . . . PT5-6 096150 . . . . . . . . . . PT5-6 096151 . . . . . . . . . . PT5-6 096152 . . . . . . . . . . PT5-6 096153 . . . . . . . . . . PT5-6 096154 . . . . . . . . . . PT5-6 096155 . . . . . . . . . . PT5-6 096156 . . . . . . . . . . PT5-6 096157 . . . . . . . . . . PT5-6 096158 . . . . . . . . . . PT5-6 096159 . . . . . . . . . . PT5-6 096165 . . . . . . . . . . PT5-6 096166 . . . . . . . . . . PT5-6 096167 . . . . . . . . . . PT5-6 096168 . . . . . . . . . . PT5-6 096169 . . . . . . . . . . PT5-6 096170 . . . . . . . . . . PT5-6 096171 . . . . . . . . . . PT5-6 096175 . . . . . . . . . . PT5-6 096176 . . . . . . . . . . PT5-6 096177 . . . . . . . . . . PT5-6 096178 . . . . . . . . . . PT5-6 096179 . . . . . . . . . . PT5-6 097015 . PT12-42, PT6-13 097016 . PT12-42, PT6-13 097017 . PT12-42, PT6-13 097018 . PT12-42, PT6-13 097019 . PT12-42, PT6-13 097020 . PT12-42, PT6-13 097021 . PT12-42, PT6-13 097022 . PT12-42, PT6-13 097023 . PT12-42, PT6-13 097024 . PT12-42, PT6-13 097025 . PT12-42, PT6-13 098175 . . . . . . . . PT12-41 098176 . . . . . . . . PT12-41 098177 . . . . . . . . PT12-41 098180 . . . . . . . . PT12-41 098181 . . . . . . . . PT12-41 098182 . . . . . . . . PT12-41 098190 . . . . . . . . PT12-41 098191 . . . . . . . . PT12-41 099024 . . PT1-62, PT1-68 099025 . . PT1-62, PT1-68 099026 . . PT1-62, PT1-68 099027 . .PT1-62, PT1-68 099028 . .PT1-62, PT1-68 099029 . .PT1-62, PT1-68 099048 . . . . . . . . PT1-61 099049 . . . . . . . . PT1-61 099054 . . . . . . . . PT1-61 099055 . . . . . . . . PT1-61 099056 . . . . . . . . PT1-61 099057 . . . . . . . . PT1-61 099060 . . . . . . . . PT1-61

099061 . . . . . . . . . 099062 . . . . . . . . . 099063 . . . . . . . . . 099100 . . . . . . . . . 099101 . . . . . . . . . 099102 . . . . . . . . . 099103 . . . . . . . . . 099104 . . . . . . . . . 099105 . . . . . . . . . 099106 . . . . . . . . . 099107 . . . . . . . . . 099108 . . . . . . . . . 099109 . . . . . . . . . 099110 . . . . . . . . . 099111 . . . . . . . . . 099112 . . . . . . . . . 099113 . . . . . . . . . 099114 . . . . . . . . . 099115 . . . . . . . . . 099116 . . . . . . . . . 099117 . . . . . . . . . 099118 . . . . . . . . . 099119 . . . . . . . . . 099120 . . . . . . . . . 099121 . . . . . . . . . 099122 . . . . . . . . . 099123 . . . . . . . . . 099124 . . . . . . . . . 099125 . . . . . . . . . 099126 . . . . . . . . . 099127 . . . . . . . . . 099128 . . . . . . . . . 099129 . . . . . . . . . 099130 . . . . . . . . . 099131 . . . . . . . . . 099132 . . . . . . . . . 099133 . . . . . . . . . 099134 . . . . . . . . . 099135 . . . . . . . . . 099136 . . . . . . . . . 099138 . . . . . . . . . 099139 . . . . . . . . . 099140 . . . . . . . . . 099141 . . . . . . . . . 099142 . . . . . . . . . 099143 . . . . . . . . . 099144 . . . . . . . . . 099145 . . . . . . . . . 099146 . . . . . . . . . 099147 . . . . . . . . . 099150 . . . . . . . . . 099151 . . . . . . . . . 099152 . . . . . . . . . 099153 . . . . . . . . . 099154 . . . . . . . . . 099161 . . . . . . . . . 099162 . . . . . . . . . 099163 . . . . . . . . . 099164 . . . . . . . . . 099190 . . . . . . . . . 099191 . . . . . . . . . 099192 . . . . . . . . . 099193 . . . . . . . . . 099194 . . . . . . . . . 099195 . . . . . . . . . 099196 . . . . . . . . . 099197 . . . . . . . . . 099198 . . . . . . . . . 099199 . . . . . . . . . 099200 . . . . . . . . . 099201 . . . . . . . . .

INDEX-7

Page Part No. PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61 PT1-61

099202 099203 099204 099205 099206 099207 099208 099209 099210 099211 099212 099213 099214 099215 099216 099217 099218 099219 099220 099221 099222 099223 099224 099225 100232 100235 100236 100238 100240 100264 100266 100268 100294 100298 100343 100344 100345 100346 100347 100348 100349 100350 100351 100352 100353 100354 100355 100356 100357 100358 100359 100360 100361 100362 100363 100364 100365 100366 100367 100368 100369 100370 100371 100372 100373 100374 100375 100376 100377 100378 100379

Page Part No.

. . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . . PT1-61 . . . . . . . . PT12-19 . . . . . . . . PT12-23 . . . . . . . . PT12-19 . . . . . . . . PT12-19 . . . . . . . . PT12-19 . . . . . . . . PT12-21 . . . . . . . . PT12-21 . . . . . . . . PT12-21 . . . . . . . . PT12-22 . . . . . . . . PT12-22 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-3 . . . . . . . . . PT12-5 . . . . . . . . . PT12-5 . . . . . . . . . PT12-5 . . . . . . . . . PT12-5 . . . . . . . . . PT12-5 . . . . . . . . . PT12-5 . . . . . . . . . PT12-5 . . . . . . . . . PT12-5 . . . . . . . . . PT12-5 . . . . . . . . . PT12-5 . . . . . . . . . PT12-5

100380 100381 100382 100383 100384 100385 100386 100387 100388 100389 100390 100391 100392 100393 100394 100395 100396 100397 100398 100399 100400 100401 100407 100450 100451 100452 100453 100454 100455 100456 100457 100458 100459 100460 100461 100462 100463 100480 100481 100482 100483 100489 100490 100491 100492 100493 100495 100496 100497 100500 100501 100502 100503 100504 100505 100506 100507 100508 100509 100510 100511 100512 100513 100514 100515 100516 100517 100518 100519 100520 100521

Page

. . . . . . . . . PT12-5 . . . . . . . . . PT12-5 . . . . . . . . PT12-5 . . . . . . . . PT12-5 . . . . . . . . PT12-5 . . . . . . . . PT12-5 . . . . . . . . PT12-5 . . . . . . . . PT12-5 . . . . . . . . PT12-5 . . . . . . . . PT12-5 . . . . . . . . PT12-5 . . . . . . . . PT12-5 . . . . . . . . PT12-5 . . . . . . . . PT12-5 . . . . . . . . PT12-5 . . . . . . . . PT12-5 . . . . . . . PT12-19 . . . . . . . PT12-19 . . . . . . . PT12-19 . . . . . . . PT12-19 . . . . . . . PT12-19 . . . . . . . PT12-19 . . . . . . . PT12-22 . . . . . . . . PT12-6 . . . . . . . . PT12-9 . . . . . . . . PT12-9 . . . . . . . . PT12-9 . . . . . . . . PT12-9 . . . . . . . . PT12-9 . . . . . . . . PT12-9 . . . . . . . . PT12-9 . . . . . . . PT12-12 . . . . . . . PT12-12 . . . . . . . PT12-12 . . . . . . . PT12-12 . . . . . . . PT12-12 . . . . . . . PT12-12 . . PT1-61, PT1-68 . . PT1-61, PT1-68 . . PT1-61, PT1-68 . . PT1-61, PT1-68 . . PT1-61, PT1-68 . . PT1-61, PT1-68 . . PT1-61, PT1-68 . . PT1-61, PT1-68 . . PT1-61, PT1-68 . . PT1-61, PT1-68 . . PT1-61, PT1-68 . . PT1-61, PT1-68 . . . . . . . . PT12-6 . . . . . . . . PT12-6 . . . . . . . . PT12-6 . . . . . . . . PT12-6 . . . . . . . . PT12-6 . . . . . . . . PT12-6 . . . . . . . . PT12-6 . . . . . . . . PT12-6 . . . . . . . . PT12-6 . . . . . . . . PT12-6 . . . . . . . . PT12-6 . . . . . . . . PT12-6 . . . . . . . . PT12-6 . . . . . . . . PT12-6 . . . . . . . . PT12-6 . . . . . . . . PT12-6 . . . . . . . . PT12-6 . . . . . . . . PT12-6 . . . . . . . . PT12-6 . . . . . . . . PT12-6 . . . . . . . . PT12-6 . . . . . . . . PT12-6

INDEX

TN


TN INDEX

Part No. 100522 100523 100524 100525 100526 100527 100528 100529 100530 100531 100532 100533 100534 100535 100536 100537 100538 100539 100540 100541 100542 100543 100544 100545 100546 100547 100548 100549 100550 100551 100552 100553 100554 100555 100556 100557 100558 100559 100560 100561 100562 100563 100564 100565 100566 100567 100568 100569 100570 100571 100572 100573 100574 100575 100576 100577 100578 100579 100580 100581 100582 100583 100584 100585 100586 100587 100588 100589 100590 100591 100592

E

Page Part No.

. . . . . . . . . PT12-6 . . . . . . . . . PT12-6 . . . . . . . . . PT12-6 . . . . . . . . . PT12-6 . . . . . . . . . PT12-6 . . . . . . . . . PT12-6 . . . . . . . . . PT12-6 . . . . . . . . . PT12-6 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . . PT12-9 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12 . . . . . . . . PT12-12

100593 100594 100595 100596 100597 100598 100599 100600 100601 100602 100603 100604 100605 100606 100607 100608 100609 100610 100611 100612 100613 100614 100615 100616 100617 100618 100619 100620 100621 100622 100623 100624 100625 100626 100627 100628 100629 100630 100631 100632 100633 100634 100635 100636 100637 100638 100639 100640 100641 100642 100643 100644 100645 100646 100647 100648 100649 100650 100651 100652 100653 100654 100655 100656 100657 100658 100659 100660 100661 100662 100663

N E Page Part No.

. . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-15 . . . . . . . . PT12-18 . . . . . . . . PT12-18 . . . . . . . . PT12-18 . . . . . . . . PT12-18 . . . . . . . . PT12-18 . . . . . . . . PT12-18 . . . . . . . . PT12-18 . . . . . . . . PT12-18 . . . . . . . . PT12-18 . . . . . . . . P