Issuu on Google+

SECO NEWS SUMMARY OF NEW PRODUCTS – MACHINING NAVIGATOR 2012

1


SECO NEWS NEW PRODUCTS: MILLING

PAGE ®

Minimaster Plus

3

Turbo 10

4

Square 6™-04

5

Highfeed2

6

TURNING TK1001 & TK2001

7

M5 Chipbreaker

8

FF2 Chipbreaker

9

SECOMAX™ CBN500

10

Small IC

11

R220.90 RANGE WITH ABEX26

CBN060K

Milling cutter and insert range for heavy duty applications. Fixed pocket cutter dimensions from Ø63 – 160mm including insert with a cutting edge length of 26mm (ABEX2606…).

Extended range. First choice for continuous to moderate interrupted cuts in hardened steel (ap <0,5 mm).

WIPER INSERT FOR SQUARE6-08 Wiper insert for (XNEX080608ZZR-M11) for Square6-08 cutters where excellent surface finish is needed. LIGHT CUTTING GEOMETRY FOR SQUARE6-08

SOLID END MILLS Jabro™ - solid2 JS530-series

12

Jabro™ JPD890

15

HOLEMAKING Crownloc® Plus

13

Seco Feedmax™ PCD drills

15

Precimaster

16

SERVICE SOLUTIONS

2

NEW ADDITIONS:

Seco Guide

17

Customer Zone

18

Threading Wizard

19

New addition of a geometry developed for exotic materials where a sharp edge is needed (XNEX080608R-M08).

HEAVY TURNING SOLID TOOL HOLDERS We offer 18 new tool holders for the heavy turning. It includes holders for both positive & negative inserts for shapes round & square. HEAVY TURNING INSERTS We are adding 25 different inserts in heavy turning which includes 3 new geometries for RCMX & 2 new geometries for SCMT 25 & 38.


MINIMASTER速 PLUS

MINIMASTER速 PLUS IS REACHING THE HIGHEST LEVEL OF PRECISION AND PRODUCTIVITY. THE SUCCESS CONTINUES Seco continues the success of Minimaster by launching the next generation. Once again showing the future direction of end mills with replaceable fluted inserts. SPEED? SURE! When a used Minimaster Plus insert is replaced with a new one, the axial and radial position remain the same for maximum precision. It is also possible to replace the insert without removing the shank from the holder or machine and re-measuring the whole assembly, speeding up the process considerably. COST EFFECTIVENESS? YOU GOT IT. You only pay for the replacement of the insert once it is worn out, instead of the complete tool (for example, HSS or solid end mill). Exchangeable inserts for different shanks allow for higher cutting data, thus avoiding regrinding and ensuring a consistent tool life.

3


TURBO 10

MAXIMUM PERFORMANCE IN SQUARE SHOULDER MILLING

HIGH PERFORMANCE SQUARE SHOULDER MILLING CUTTERS Turbo10 is a new high performance cutting tool for square shoulder milling, with improved tool life and precision. This is achieved through optimised cutting properties that reduce heat generation and cutting forces, and a new insert geometry that mills corner angles to 90 degrees. Turbo10 is very flexible and suitable for most milling operations, including roughing, semi-finishing, finishing by slotting, contouring, helical interpolation and ramping. Initially it will be available in diameters from 16 to 100 mm with 0.4 and 0.8 mm insert radii, two geometries and eight insert grades. Turbo10 can be mounted with cylindrical shank, Weldon, arbor and Combimaster.

4


SQUARE 6-04

THE SQUARE 6 SUCCESS CONTINIUE WITH A LITTLE BROTHER. THE SQUARE 6 SUCCESS CONTINUES WITH A LITTLE BROTHER. Here is the smaller size of Square 6 for square shoulder milling, Seco is adding Square 6-04 which is covering the main machining depth of cut with maximum 4mm capability. Square6-04 is well suited for small and medium milling machines. The inserts have six cutting edges and when combined with the maximum number of inserts on each cutter dimension it results in improved cost-efficiency and increased productivity. HIGH PERFORMANCE WITH SQUARE6-04 And with two different pitches - same diameter, different number of teeth - Square 6 gives the same high performance on a wide range of materials, operations and machining conditions. The 90째 setting angle ensures a true 90째 square in one operation, saving valuable production time.

Square 6-08

Square 6-04

5


HIGHFEED2

FIRST STEP OF NEXT GENERATION SOLUTIONS FOR HIGH FEED APPLICATIONS WITH PEAK PERFORMANCE AND RELIABILITY

EVEN FASTER WITH THIS NEW GENERATION Highfeed2 is a new range of small diameter high feed tools, intended for very high productivity in modern CNC machines. Highfeed2 enables a combination of strength and number of teeth versus diameter for maximum metal removal rate. The close pitch allows very fast feed rates and stable cutting performance even in very interrupted cuts. The “well balanced design” of both body and inserts gives free chip flow when copy milling in cavities, particularly when using tool holders with long overhang. Designed for very high feed rates with low depth of cut, Highfeed2 is available from diameter 16 to 35 mm and relevant imperial sizes with comprehensive insert grades and geometries to cover a wide spectrum of materials including superalloys.

6


TK1001 & TK2001

DURATOMIC® GRADES FOR CAST IRON

IT’S ALL ABOUT MAKING IT EASY How would you like to reduce your internal logistic costs, your stock handling costs, labour costs… the list goes on. With the new TK grades that’s exactly what you can do. The general application cast iron grade was designed for long tool life in various CIs, effectively reducing the number of grades needed in cast iron applications. DURATOMIC DOES IT AGAIN Decrease your cost per part with longer tool life due to the Duratomic coating. It offers superior wear resistance saving you money and increasing productivity.

7


M5 CHIPBREAKER ROBUST CHIPBREAKER FOR HIGHEST DEGREE OF EFFICIENCY

A STRONG GEOMETRY FOR HIGH METAL REMOVAL When productivity and strength is an issue then the rigid centre lock geometry M5 is the proper choice. This robust insert with its highly protected chip groove tackles the most demanding operations, heavy interruptions and rough skin successfully. An open chip groove with welladapted cutting angles ensures high feed rates and large cuts for efficient machining and best economy. Ductile materials can easily be handled with full control by the finetuned chip groove design. For obtaining optimal tool life in a variety of materials the balanced rake face minimizes the heat transferred to the insert. M5 is the unsurpassable geometry for a great variety of workpiece materials such as steel, stainless steel, cast iron and troublesome superalloys. Positive centre lock inserts are available in a wide range of chipbreakers to cover most materials and applications, F1, MF2, F2 and M3 are the foundation. The new M5 will complement these as the strongest geometry for the most testing environments and the heaviest applications.

8


FF2 CHIPBREAKER A GEOMETRY FOR FINISHING WHERE STRICT CHIP CONTROL IS A PRIORITY

A CHIP FORMER FOR SUPERIOR PERFORMANCE IN DUCTILE MATERIALS Chip control is highly important in modern production where less manned supervision is present. Selecting the FF2 geometry in negative insert style can prevent machining stops caused by unbroken chips which are hard to evacuate from the machine. An even more undesirable situation is when the uncontrolled swarf sticks to the cutting tool or the component causing sudden tool failures or poor part quality. The very tight, narrow chip groove of FF2 curls the chips firmly against the insert or component and compels them to break into easy-handled size. Even if the mechanical maneuvering of the chips is intensive the well-balanced design of the chip groove minimizes the cutting forces and reduces the heat transferred to the insert. When less heat is transferred tool life is improved. Low cutting forces generated by the insert enable operations to be performed in unstable set-ups and in thin-walled components. FF2 is an excellent complement to the existing FF1 and MF2 offering excellent opportunities in the finishing of ductile materials, steels and stainless steels.

9


SECOMAX CBN500

INVENTED EXCLUSIVELY FOR WHITE CAST IRON MACHINING HIGH CHROME HARD IRON - A HARD CHALLENGE TO MACHINE Compared to today’s standard solution for machining white cast iron components, CBN500 offers you more. A lot more. You can increase your tool life, and at the same time improve its repeatability – you can predict a long tool life, which will reduce downtime and insert consumption. The increased cutting time will give you reduced costs. There’s more – CBN500 is tougher than ever giving you fewer tool changes, less downtime and more savings.

10


SMALL IC NEW AND COST EFFECTIVE SOLUTIONS FOR SMALL INSERTS SMALL BUT TOUGH

A PERFECT BALANCE

With the full face format of the small IC insert there is no risk of debrazing, giving you maximum reliability in production. Also the cost per edge is normally lower compared to brazed single tip or multi corner inserts. As well as decreasing the cost per edge, we can increase your tool life. Weâ&#x20AC;&#x2122;ve given the Small IC inserts superior edge toughness and wear resistance using the latest technology for modern substrates and coating. This means long, predictable tool life, less down time and less dimensional adjustments.

Small ICs have unchamfered edges with optimized edge honing, meaning a reduction in rejected components due to less risk of vibrations. The radial and axial cutting forces are balanced so that even complex parts with a weak set up can successfully be machined. You can get holders and inserts from one supplier which makes ordering easy and lowers the risk of mixing up inserts, toolholder pockets and clamp screws, Simple.

SAVE 50% MACHINING TIME If you are brave enough to change your machining strategy we could help you save more than 50% machining time. Interested? No limitations on tip size give you full use of the cutting edge length and the possibility to use different machining strategies e.g. Plunge turning. Meaning you can decrease your machining time by more than 50% compared to conventional turning. Interested now?

11


JABRO™- SOLID2 JS530-SERIES

A FULL RANGE OF VERSATILE SOLID CARBIDE BALL NOSE CUTTERS

FEATURES & ADVANTAGES

JABRO™ SOLID2 BALL NOSE CUTTERS Jabro™-Solid2

solid2

ball nose (JS530 series), a full radius geometry in the range for general machining with flexibility, speed and efficiency. The JS530 series is designed for copy and profile milling as well as slotting and side milling operations.

• Radial relief o - Results in a strong cutting edge • Polished Siron-A coating o - Reduction of friction and heat build up • Increased core diameters related to number of teeth o - Adds stability, reduces deflection and reduces the risk of chips clogging the flute space • Edge Prep o - Result in a controlled wear pattern

12


CROWNLOC® PLUS EXCHANGEABLE TIP DRILLS CROWNLOC® PLUS

FEATURES

Crownloc® Plus is a new generation of Seco drills with exchangeable crowns. Featuring new geometry, coating and locking interface, Crownloc Plus improves chip evacuation and wear resistance in a variety of materials. Moreover, it requires no regrinding or resetting.

Strong drill body design

COST EFFICIENCY WITH CROWNLOC® PLUS Decrease your cost /hole with longer tool life using Crownloc Plus. It offers superior wear resistance as well as hole quality; increasing the output and saving you money.

- High strength locking interface - Deep and wide flutes - Polished body New optimised geometry - Improved chip formation - Enhanced entering capability - Increased wear resistance - TiAlN coating

CROWN

P-GEOMETRY – Universal geometry

13


PCD SOLUTIONS FOR COMPOSITE MACHINING

PCD SOLUTIONS PCD CHARACTERISTICS

SHARP CUTTING

PCD tools for thermosetting plastics and thermoplastics are characterized by five important features. These are;

The very sharp cutting edge compared to a CVD Dura coated tool allows a PCD tool to perform consistently and securely. This means that the workpiece will have equal surface finish showing no or minimum delamination. The narrow manufacturing tolerances make the process stable, predictable and repeatable.

1. Sharpness of the polycrystalline diamond results in an improved surface finish, a good fibre cut and low heat generation. These benefits minimize uncut fibres and delamination, increase productivity and improve process security 2. Hardness of the polycrystalline diamond makes the tools more wear resistant and increases the tool life 3. The accuracy of the PCD tools results in close dimensional tolerances increasing the reliability, allowing you to reduce finishing operations 4. The thermal conductivity of the polycrystalline material lowers process temperatures which enhances product stability and allows higher cutting speeds. 5. After-sales services: re-conditioning results in a new tool that increases tool life and reduces tool costs

14


PCD SOLUTIONS FOR COMPOSITE MACHINING

PCD SOLUTIONS

JABRO™- COMPOSITES JPD890 SERIES

SECO FEEDMAX PCD DRILLS

FLEXIBILITY

FLEXIBILITY

Optimized PCD milling geometry for composite materials The complete range of Jabro PCD cutters have a special PCD Blade design that improves the thermal wear resistance. This design allows a higher feed rate because of its resistance to cutting force effects. By offering 3 versions of shear angle the direction to guide the cutting forces can be chosen. Conventional

The new range of PCD drills have a special 120° drill point design that can be used in various applications. In addition, customized tools are available upon request. For example: chamfer drills, double point…

Tool picture

PERFORMANCE INCREASE Internal through coolant channels All standard PCD milling tools are equipped with two through coolant channels. By applying through coolant emulsion the cutting temperature can be reduced. A lowered process temperature reduces the risk of melting resin and allows an increase in cutting speed in comparison to PCD tools without through coolant channels.

PERFORMANCE INCREASE One of the strongest benefits with PCD drills is their ability to cut for long periods of time without needing replacement. The stock standard PCD drills are without coolant holes. The standard 30° helix angle secures the chip/dust evacuation. The sharpness and the excellent dimensional tolerance of a PCD tool improves workpiece quality in terms of surface finish and hole tolerances. Resulting in long tool life and an increased yield. The full potential and value of PCD drills over conventional drilling can be seen in enhanced productivity and tool life. For full cost efficiency when using PCD tools, a reconditioning service is available for all Seco PCD tools.

15


PRECIMASTER RX2000 & RX1500 HIGH PERFORMANCE GRADES FOR PRECIMASTER REDUCE YOUR REAMING RUNNING COSTS How important is it to you to lower your reaming operation costs? We can help you reduce your costs. The hardness of the new RX2000 has been increased by 30% compared to the existing CP20. This gives an increased tool life and performance and an improved wear resistance. Want to reduce your reaming costs? We can help. CUT THE SCRAP RX1500 grades will also help reduce your scrap costs. With improved chip control giving you improved application safety, problematic chip evacuation can be eliminated.

GRADES RX2000 RX1500

High performance coated carbide grade for steel and cast iron Wear resistant coated cermet grade for performance optimization in steel and cast iron

GEOMETRY CHOICE

EB45: Chip control +++ Surface finish: Ra 0,8 - 1,2 First Choice

16

EB845: Chip control ++ Surface finish: Ra 0,2 - 0,8

EB25: Feed +++ Chip control + Surface finish: Ra 0,4 - 0,8


SECO GUIDE

CUTS RIGHT TO THE EDGE • The Seco Guide enables the user to search for products via Product Group

• Can I search for my product in a fast way? Of course, by using Quick Search, just start typing and the hit list will find it for you

• What matches with what? You can look that up by using Tool Combination’s tab

• Find out which attributes our products have

• The Seco Guide enables the user to search for products via Seco Material Group • Create your favourite list and add your favourite products • Transfer your product to Seco Cut and calculate cutting data

• See our products in different ways with the images that the application holds • The Seco Guide gives the user opportunities to search for all of Seco Tools’ standard products ( approx. 33000 products) • It gives the user possibilities to combine multiple search methods to find just the tool you are looking for

• Transfer your threading product to the Threading Wizard • The Seco Guide enables the user to search for products via Cutting Method • What spare parts or accessories do I need? Check that out with the help of the Spare Parts/Accessories tab • Log in inside the application or log in via the Customer Zone to see the price and the recommended stock status of your product

17


CUSTOMER ZONE ALL SECO INTERACTIVE APPLICATIONS GATHERED IN ONE PLACE

THE CUSTOMER ZONE In the corporate websiteâ&#x20AC;&#x2122;s new Customer Zone, Seco Tools has gathered all the interactive applications needed for efficient component production. At the same time, the applications have been updated and upgraded with more functionality. Previously, Secoâ&#x20AC;&#x2122;s applications were not so easy to find; they had to be downloaded to your computer. Now all programs have been gathered into a comprehensive environment and can be run directly from a web browser. BE UP-TO-DATE One of the biggest differences is that the data surrounding an application is always up-to-date, regardless of the application. A personal login feature enables users to see the prices of all standard products and the applications that do not require online access can be used off line without a login, meaning that users can take laptops to the shop floor and use the programs there.

18


THREADING WIZARD

GENERATE YOUR OWN CNC THREADING PROGRAM

QUICK AND EASY TO USE

The new Seco Threading Wizard uses our global core systems for product and cutting data so that new products can be continually updated, giving you access to fast and reliable information. It will take you step by step through the process of generating a CNC program for your threading application whether it is a milling or turning task. The application starts with some basic information about the thread form and workpiece dimensions, and takes you through tool selections and machine tool parameters to create a customised CNC output tailored to your requirements. Finally you can save, print or import the code directly into your CNC control.

• Supports the following thread forms - ISO - UN - UNJ - MJ - BSW Whitworth - Round DIN 405 - Trapezoidal DIN 103 - ACME-G - Stub ACME - BSPT - Rc - NPT - NPTF

- Supports the following CNC controls • Fanuc G32 • Fanuc G33 • Hidenhaim • Mazatrol ISO/EIA • Siemens - Benefit from Seco’s unique experience of threading applications - Cutting data for the latest products - Multi language support - Tailored CNC program to suit your requirements

19


#4)'06+0#5GEQ6QQNU#TIGPVKPC5#6GN  

 (CZ  

#7564#.+#5GEQ6QQNU#WUVTCNKC2V[.VF6GN  

   NQECNVGN

 (CZ      NQECNHCZ

  #7564+#5GEQ6QQNU)GUOD*6GN    (CZ     $'.)+7/5GEQ6QQNU$GPGNWZ085#6GN   

 (CZ   

 $150+#5GG5QNXGPKC$4#<+.5GEQ 6QQNU+PFG%QO.VFC6GN   

(CZ   $7.)#4+#5GG5YGFGP%#0#&#5GEQ6QQNU%CPCFC+PE6GN

  (CZ

  %*+0#5GEQ6QQNU5JCPIJCK%Q.VF6GN   

(CZ      %1.1/$+#4GZEQ 6QQNU6GN   (CZ

%41#6+#5GG5NQXGPKC%<'%*4'27$.+%5GEQ6QQNU%<UTQ6GN  

 (CZ   

  &'0/#4-5GEQ6QQNU#56GN

(CZ  (+0.#0&5GEQ6QQNU1;6GN 

 

(CZ  

  (4#0%'5GEQ6QQNU(TCPEG5#6GN     (CZ     5GEQ'2$6GN   (CZ     5GEQ'VU2NCPEJG5#6GN  (CZ   )'4/#0;5GEQ6QQNU)OD*6GN     (CZ      )4''%'#VJGPU/GEJCPKEC6GN     (CZ     *70)#4;5GEQ6QQNU-(66GN    (CZ    +0&+#5GEQ6QQNU+PFKC2.VF6GN   

(CZ    +0&10'5+#5GEQ6QQNU5'#2VG .VF6GN       (CZ      +6#.;5GEQ6QQNU+VCNKC5R#6GN    (CZ     NQECNHCZ  

 ,#2#05GEQ6QQNU,CRCP--6GN  (CZ   /#%'&10+#5GG5NQXGPKC/#.#;5+#5GEQ6QQNU /CNC[UKC5&0$*&6GN 

  (CZ 

  /':+%15GEQ6QQNUFG/GZKEQ6GN(CZ     /106'0')41 5GG5NQXGPKC0'6*'4.#0&55GEQ6QQNU$GPGNWZ086GN   

(CZ    5GEQ,CDTQ6QQNUDX6GN  (CZ 0'9<'#.#0&5GEQ6QQNU0GY<GCNCPF.VF6GN   (CZ    0149#;5GEQ6QQNU #56GN  

(CZ   2*+.+22+0'55GG5KPICRQTG21.#0&5GEQ6QQNU2QNCPF5R\QQ6GN     (CZ    21467)#.5GEQ6QQNU2QTVWICN.FC6GN    (CZ    41/#0+#5GEQ6QQNU4QOCPKC 54.6GN   (CZ    4755+#5GEQ6QQNU4WUUKC6GN   (CZ   5'4$+#5GEQ 6QQNU54$FQQ6GN    (CZ   

5+0)#214'5GEQ6QQNU5'#2VG.VF6GN    (CZ   

5.18#-+#5GEQ6QQNU5-UTQ6GN (CZ  5.18'0+#5GEQ6QQNU5+FQQ6GN     (CZ     5176*#(4+%#5GEQ6QQNU5QWVJ#HTKEC2V[.VF6GN   (CZ   5176*-14'#5GEQ6QQNU -QTGC.VF6GN    (CZ  

52#+05GEQ6QQNU'URCÌC5#6GN (CZ  59'&'0 5GEQ6QQNU#$6GN  



(CZ    59+6<'4.#0&5GEQ6QQNU#)6GN    (CZ    6#+9#0 5GEQ6QQNU5'#6CKYCP6GN     (CZ     6*#+.#0&5GEQ6QQNU6JCKNCPF%Q.VF6GN     (CZ    674-';5GEQ6QQNU#56GN

   

(CZ

   7-4#+0'5GEQ6QQNU7MTCKPG6GN    

 (CZ   

 70+6'&-+0)&1/5GEQ6QQNU7-.VF6GN  (CZ   75#5GEQ6QQNU +PE6GN   

(CZ     8+'60#/5GEQ6QQNU5'#2VG.VF6GN      (CZ    

5GEQ6QQNU#$ (CIGTUVC5YGFGP6GN  



 YYYUGEQVQQNUEQO



 56   )$5'%1611.5#$2TKPVGFD['NCPFGTU 


GB Seco News Summary 2011 #2