Page 1

PRODUCT DATA SHEET

ELASTO-QOTE® GS Application Instruction: Surface Preparation Steel Product Information

General

®

Product description: Elasto-Qote GS is s solvent-free spray-applied aromatic pure Polyurea elastomeric coating system for the protection of steel and concrete substrates found in water-and waste water treatment plants, Offshore, power industry, mining, civil constructions and petrochemical industry where a fast return to service time is required. The Elasto-Qote® GS is excellent abrasion and impact resistant and has good crack-bridging properties on concrete substrates. Features:  100% Solids Pure Polyurea Elastomer  No VOC  User friendly 1:1 mixing ratio  Excellent water and waste water resistant  Very fast set-time for reducing handling and return to service  Not sensitive for humidity during application  Service temperature (dry) from -40 up to 130°C (-40 up to 266˚F)  Can be applied from -10 up to 49˚C (14 up to 120˚F)  Can be used to protect steel, concrete and various other substrates  Unlimited film-build in one single multi-pass application  Excellent impact and abrasion resistant  Available in multiple colours (RAL)  Topcoat available for optimum UV resistance and colour retention

Application examples Application: water-and waste water treatment services, secondary containment areas, manholes, pipelines, storage tanks, digesters, clarifiers, penstocks, cooling towers, sedimentation reservoirs, hoppers, platforms, biogas reactors, pools, park decks and ramps, bridge- and tunnel construction and many other services.

Preventing condensation on the substrate Abrasive Blasting Recommended Surface Profile

Application Instruction: Surface Preparation Concrete General

Preventing condensation on the substrate Recommended Surface Profile Abrasive Blasting

Test Method ASTM 1737 ASTM G14 ASTM D4541 ASTM D4541 ASTM D4060 ASTM D624 ASTM D638 ASTM D638 ASTM D570 ASTM D2240

Typical Value Pass 1/8” Mandrel >132 in-lb/>15Nm/>15J >1160 psi/>8MPa >217 psi/>1.5MPa 6mg. loss >256 in-lb/>45N/mm >3625psi/>25MPa >350% <1.80% 45 Shore D

General Product Information Colour Finish Primer

Dry Film Thickness Coverage Rate (theoretical)

Volume Solids VOC Content Flash Point Mixing Ratio Potlife

Grey or Black (other colors on request) Gloss Elasto-Qote® Epoxy Primer, Urethane Primer or VE Basecoat. Recommended primer depends on the specific substrate type and conditions. Consult your local Elasto-Qote® representative. Minimum 1000 micron (40 mil). Maximum: no limit. 54.2 sq.ft/USG at 30mils (500micron)DFT. 1,33m2/l at 30mils (750micron)DFT. 40.8 sq.ft/USG at 40mils (1000micron)DFT. 1,00m2/l at 40mils (1000micron)DFT. 100% 0 g/l. >200˚F (>93˚C) 1:1 (A to B in volume) NA

Concrete must be at least 28 days cured at 75˚F (24˚C). The area to be coated has to be clean, dry and free from oil, grease and dust. All contamination that could interfere with the adhesion of the coating has to be removed according to SSPC-SP1 or equal. Leaks and water infiltrations must be eliminated. Remove free-standing water, repair excessive cracks and resurface exposed aggregate and small voids with a suitable high-strength, fast curing, non-shrinking product. Prior and during the surface preparation, the temperature of the substrate(s) must be at least 5˚F (3˚C) above the dew point. CSP 4-6. Do not overblast the concrete. SSPC-SP13/NACE 6

Application Safety General

Product Performance Flexibility Impact Resistance Adhesion to Steel Adhesion to Concrete Abrasion Resistance Tear Strength Tensile Strength Elongation at break Water Absorption Hardness

The area to be coated has to be clean, dry and free from oil, grease and dust. All contamination that could interfere with the adhesion of the coating has to be removed according to SSPCSP1. Prior and during the surface preparation, the temperature of the substrate(s) must be at least 5˚F (3˚C) above the dew point. Minimum Sa2½ (SSPC-SP10/ NACE2) . 3-4mils (75-100micron) angular profile.

Read the Product Data Sheet and follow the caution statements on the Material Safety Data Sheet. Personnel who will come into contact with the product should be using appropriate protection equipment. Follow national safety guidelines

Application Conditions Product Surface Ambient Humidity 158-176˚F 70-90˚F 50-100˚F 0-50% (70-80˚C) (21-32˚C) (21-32˚C) Minimum 158˚F 14˚F 14˚F 0% (70˚C) (-10˚C) (-10˚C) Maximum 176˚F 120˚F 120˚F 98% (80˚C) (49˚C) (49˚C) Prior and during the application, the temperature of the substrate(s) must be at least 5˚F (3˚C) above the dew point. Optimum

Application Instruction: Plural Component Spray Step 1 Step 2

Step 3

Step 4

Mix the Part A (Resin) until uniform in consistency and keep it under agitation. Use only heated plural component Airless equipment capable to maintain a 1:1 ratio in volume and 1.25 Gallon/4,73 Liter per minute output, with heated drums, insulated (heated) hoses and minimum 130bar (1885psi.) fluid pressure for both Part A as well Part B. Use an impingement mix Airless spray-gun with preferably changeable spray tips. Consult Elasto-Qote® for specific information. Both part A and B must be heated up and maintained to a temperature of 70-80˚C (158176˚F). Apply Elasto-Qote® GS in the recommended DFT. Use a WFT gauge to check. Do not dilute the product.

DISCLAIMER: Seal For Life Industries warrants that the product(s) represented within conform(s) to its/their chemical and physical description and is appropriate for the use as stated on the respective technical data sheet when used in compliance with Seal For Life Industries written instructions. Since many installation factors are beyond the control of Seal For Life Industries, the user is obligated to determine the suitability of the products for the intended use and assume all risks and liabilities in connection herewith. Seal For Life Industries liability is stated in the standard terms and conditions of sale. Seal For Life Industries makes no other warranty either expressed or implied. All information contained in the respective technical data sheet(s) should be used as a guide and is subject to change without notice. This document supersedes all previous revisions. Please see revision date on the left. Elasto-Qote® is a registered trademark of Seal For Life Industries.

AUGUST 2013 (EN)

Page 1/2


Elasto-Qote® GS Curing Times at 70˚F (21˚C)

Additional Information

Gel Time Dry to Touch Dry to Handle Foot Traffic Industrial Traffic Recoat Time Full Cure

Documentation

5-15 seconds 15-30 seconds 5-10 minutes 1 hour 2 hours 0-12 hours 12 hours

(ready for Holiday test) Certified staff (without preparation) (ready for service)

Application instructions and other documentation can be obtained by contacting our head office, from our local distributor or by sending email to info@sealforlife.com Application of the described coating system should be carried out and inspected by certified personnel.

Inspection and Repair Inspection

Coating Thickness

Repair

The finished coating must be visually inspected for any defects, such as runs and sags, fisheyes, blistering, pinholes, missed spots and possible contaminants. Pinhole/Holiday detection must generated according to NACE SP0188 (for steel substrates only). The coating thickness (DFT) must be within the specified DFT range. Use calibrated equipment and measure according to SSPC-PA 2 or other specified standard. Pinholes/Holidays must be located and repaired with approved material. Consult Elasto-Qote® for specific information. Retest the repaired area.

Cleaning Cleanup

Use MEK or NMP.

Handling General

Transport and stacking is possible after full cure of the coating and generating a Holiday test (NACE SP0188). This time can be reduced by increasing the curing temperature. Consult Elasto-Qote® for specific information.

General Order Information Product

Elasto-Qote® GS. Product dimensions and contents:

Small Drum Part A (Resin) Part B (Iso)

5.28 gal/20 l 5.28 gal/20 l

(48.94 lb/22,2 kg) (44.97 lb/20,4 kg)

Drum Part A (Resin) Part B (Iso)

52.8 gal/200 l 52.8 gal/200 l

(489.42 lb/222 kg) (449.74 lb/204 kg)

Cartridges

Available on request.

Handling Storage

Handle with care. Keep containers upright. Store indoor, clean and dry, away from direct sunlight in a cool place between 65-85°F(1830°C). Keep from freezing. Shelf life 12 months in the original unopened containers.

Seal For Life Industries LLC Houston, TX, USA Tel: +1 713 676 0085 Toll Free: +1 888 676 7202 Fax:+1 713 676 0086 houston@sealforlife.com

Seal For Life Industries Tijuana, Mexico Tel USA: +1 858 633 9797 Fax USA: +1 858 633 9740 Tel Mx: +52 664 647 4397 Fax Mx: +52 664 607 9105 mexico@sealforlife.com

Seal For Life Industries BV Stadskanaal, the Netherlands Tel: +31 599 696 170 Fax: +31 599 696 177 info@sealforlife.com

Seal For Life Industries BVBA Westerlo, Belgium Tel: +32 14 722 500 Fax: +32 14 722 570 belgium@sealforlife.com

Seal For Life Private Ltd. Baroda, India Tel: +91 2667 264 721 Fax: +91 2667 264 724 india@sealforlife.com

Anodeflex® - Stopaq® - Polyken® - Covalence® - Powercrete® - Sealtaq® - Blockr® - Elasto-Qote® DISCLAIMER: Seal For Life Industries warrants that the product(s) represented within conform(s) to its/their chemical and physical description and is appropriate for the use as stated on the respective technical data sheet when used in compliance with Seal For Life Industries written instructions. Since many installation factors are beyond the control of Seal For Life Industries, the user is obligated to determine the suitability of the products for the intended use and assume all risks and liabilities in connection herewith. Seal For Life Industries liability is stated in the standard terms and conditions of sale. Seal For Life Industries makes no other warranty either expressed or implied. All information contained in the respective technical data sheet(s) should be used as a guide and is subject to change without notice. This document supersedes all previous revisions. Please see revision date on the left. Elasto-Qote® is a registered trademark of Seal For Life Industries.

AUGUST 2013 (EN)

Page 2/2

Elastoqote gs august 2013  
Read more
Read more
Similar to
Popular now
Just for you