Page 1

TEST REPORT Mechanical & Hardgoods Laboratory

Report No.: Page: Date:

TH50159B/2014 OF 6 JUN. 11 ,2014

PRO LITE 5F-128, FU CHIANG ST., TAICHUNG- TAIWAN The following merchandise was submitted and identified by the applicant as: Product Description: Frame Style/Item No.: CDS-233 (Menaggio) ManufacturerNendor: PRO-LITE Quantity: 3 pes of Frames We have tested the submitted sample(s) as requested and the following results were obtained: Test Requested: For compliance with Clause 4.8.2.2, Clause 4.8.3.2, Clause 4.8.4.2 and Clause 4.8.5.2 of EN 14781 :2005 Racing bicycles - Safety requirements and test methods. Test Method:

According to Clause 4.8.2.3, Clause 4.8.3.3, Clause 4 .8.4.3 and Clause 4.8.5.3 of EN 14781:2005 Racing bicycles - Safety requirements and test methods.

Sequence ofTesting:

Sample No. # 1 :Clause 4.8.5.3. Sample No. #3 :Clause 4.8.4.3 , Clause 4.8.2.3 and Clause 4.8.3.3.

Test Result:

--See following sheet(s)--

Date of Receipt:

MAY 19,2014, MAY 22, 2014, JUN. 05,2014

Testing Period: --- See Next Page ---

MAY 19, 2014 - JUN. 11, 2014

Signed for and on behalf of SGS Taiwan Ltd.

Testing Place: No. 9, 14th Rd., Taichung Ind. Park, Taichung City 40755, Taiwan

Kaini Chen Team Leader

Th1s document i~ issued by the Company_sub1ect to its General C~nd1tions of Service printed overleaf, available on reQuest or accessible ~~;t!Jtto;!Jwww sos.com/enfTecms:and·l;;onqitions aspx and. for electromc format documents, subject o Terms and ConditiOns for Electromc Documents at http·Uwww sgs co!!!len!Terms-and-Coqdii•~-!!:.Q!:>Ql!!i!!nt'JJ;JllL Attent1on IS drawn to the limitaUon of liability, Indemnification and jurisdiction Issues defined !herem. Any holder of this document is advised that information contained hereon reflects the Company's findings at the time of 1ts .Intervention only and Within the lim1ts of Client's instructions, if any. The Company's sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except In full. without prior written approval of the Company. Any unauthorized alterat,on, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. Q

T

, 1 l I. ~ ~ .ft.l!a #41~fif ;t) m, ;~ J)

3 5 g32 7

127. Wu Kung Road, NewTa1pei Industrial Park, NewTaip01 City. Taiwan/N!f:JI:. rpfffr:JI:.J.i "t'OO g.n..:r:.4127*. t 1886·2) 2299-3279 f (886·2) 2299·2920 www.sgs.tw Member ol SGS Group


TEST REPORT Mechanical & Hardgoods Laboratory

Report No.: Page:

TH50159B/2014 2 OF 6

Test Result: Clauses: 4.8.2 Frame and front fork assembly- impact test (falling mass) 4.8.2.2 Requirement When tested by the method described in 4.8.2.3, there shall be no visible cracks or fractures in the assembly and there shall be no separation of any parts of any suspension system. The permanent deformation measured between the axes of the wheel axles (the wheel-base see 3.23) shall not exceed the following values: a) 30 mm where a fork is fitted; b) 15 mm where a solid-steel bar is fitted in place of a fork.

Result Pass

4.8.2.3 Test method Figure:

5

A c t uaIF'm d m~: '

Test clause Clause 4.8.2.3 Remark

Requirement Test Result < 15mm 0.4mm There was no visible crack on the sample after testing.

Note:

1. Information of sample: Material (Carbon), Mass (1 ,670 g), Frame (560 mm). 2. The rigid fork which is needed to conduct the test was provided by SGS Taiwan and rigid fork is 357 mm in length. 3. Sample No. #3. --- See Next Page---

This document is issued by the Company sub1'ect to its General Conditions of Service printed overleaf, available on re uest or accessible at · . • ·· and for electronic format documents, subject o Terms and Conditions for Electronic Documents at · • • · . • Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company's findings at the time of its .intervention only and within the limits of Client's instructions, if any. The Company's sole responsibility is to its Client and this document does not exonerate part1es to a transaction from exerc1s1ng all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this documenl is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested.

3 5 Q9 3 2 8

~ ~:lk ~H~UH};t) ~~ .i)

127. Wu Kung Road, New Taipe1lndusmal Park. New Taipei City. Taiwan /HiT ;1:. rp HiT ;1:.,4.1: 00 g Ji...I-~127~ t 1886-2) 2299-3279

f (886·21 2299-2920

www.sgs.tw Member of SGS Group


TEST REPORT Report No.: Page:

Mechanical & Hardgoods Laboratory

TH50159B/2014 3 OF 6

Test Result: Clauses: 4.8.3 Frame and front fork assembly- impact test (falling frame) 4.8.3.2 Requirement When tested by the method described in 4.8.3.3, there shall be no visible cracks or fractures in the assembly and after the second impact, the permanent deformation measured between the axes of the wheel axles (the wheel-base - see 3.23) shall not exceed 15 mm for a frame-fork assembly and there shall be no separation of any parts of any suspension system.

Result

Pass

4.8.3.3 Test method Figure:

\ \

-~j \

I I I

A ctuaIF"m d.mg: Test clause Clause 4.8.3.3 Remark

3

Requirement Test Result I 0.2 mm < 15mm I There was no visible crack on the sample after testing.

1. Infonnation of sample: Material (Carbon), Mass (1,670 g), Frame (560 mm). 2. The rigid fork which is needed to conduct the test was provided by SGS Taiwan and rigid fork is 357 mm in length. 3. Sample No. #3. --- See Next Page --Note:

This document is issued by the Company sub1"ect to its General Conditions of Service printed overleaf, available on re uest or accessible at · • • ·· and for electronic format documents, subject o Terms and Conditions for Electronic Documents at · . • ·· . • Attention 1s drawn to the lim1tation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that infonmation contained hereon reflects the Company's findings at the time of its .intervention only and within the limits of Client's instructions, if any. The Company's sole responsibility is to its Client and this document does not exonerate parties to a transaction from exerc1s1ng all their nghts and obligations under the transaction documents. Th1s document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results Q shown in this lest report refer only to the sample(s) tested.

3 5 g 32g

{; ~oltAkH4Ul:{st.:tf ffl./~ J)

127. Wu Kung Road. New Tatpei Industrial Park. New Ta1pei City, Taiwan/ -8JT ;t, rp -liT;!:,;.{ 1: 00 g Ji.I.~l27~ t (886·21 2299 3279 f (886-2) 2299 2920 www.sgs.tw Member of SGS Group


TEST REPORT Mechanical & Hardgoods Laboratory

Report No.: Page:

TH50159B/2014 4 OF 6

Test Result: Clauses: 4.8.4 Frame - fatigue test with pedalling forces 4.8.4.2 Requirement When tested by the method described in 4.8.4.3, there shall be no visible cracks or fractures in the frame, and there shall be no separation of any parts of any suspension system. For carbon- fibre frames, the peak deflections during the test at the points where the test forces are applied shall not increase by more 20% of the initial values.

Result Pass

4.8.4.3 Test method Figure: A

c

r~7 A ctua IF.m d.mg:

Test clause Clause 4.8.4.3 Remark

----------Left Right Remark

Force

Test conditions Frequency

Cycles

Test Result (Cycles)

1,100 N

3Hz

100,000

100,000

There was no visible crack on the sample after testing. Peak deflections during_ the test Initial values Final values Test Result 20.55 mm 22.19 mm Pass Pass 22.59mm 24.34mm The peak deflections was no more than 20% of the initial values.

Note:

1. lnfonnation of sample: Material (Carbon), Mass (1 ,670 g), Frame (560 mm). 2. The rigid fork which is needed to conduct the test was provided by SGS Taiwan and rigid fork is 357 mm in length. 3. Sample No. #3. ---See Next Page---

This document Is ISsued by the Company sub!·ect to its General Conditions of Service printed overleaf, available on re uest or accessible at · ·· and. for electronic format documents. subject o Terms and Conditions for Electronic Documents at · . ·· - Attent on 1s rawn to the l1mitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is adv1sed that information contained hereon reflects the Company's find1ngs at the time of its intervention only and w1thin the limits of Client's instructions, If any. The Company's sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their nghts and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results Q shown in this test report refer only to the sample(s) tested. 1

3 5 Qg 3 3

~ ~4t-lla~HUHr;tr ffi_J~ J]

127. Wu Kung Road, New Tatpetlndusmal Park. New Tatpei City, Taiwan /-$f 31:. 'f1 -$f 31:....! "f l!J I;& Ji..J.4127*. t (886 2) 2299-3279 f (886·2) 2299-2920 www.sgs.tw Member ol SGS Group


TEST REPORT Mechanical & Hardgoods Laboratory

Report No.: Page:

TH50159B/2014 5 OF 6

Test Result: Clauses: 4.8.5 Frame- fatigue test with horizontal forces 4.8.5.2 Requirement

Result

Pass

When tested by the method described in 4.8.5.3, there shall be no visible cracks or fractures in the frame and there shall be no separation of any parts of any suspension system. For carbon- fibre frames, the peak deflections during the test in either direction from the mean position shall not increase by more than 20% of the initial values. 4.8.5.3 Test method

Figure:

2

A ctu a I F.m d.mg:

Test clause Clause 4.8.5.3 Remark

I -----------I s·

1 Pull(+) mg e Push(-) Remark

Test conditions Frequency

Force Cycles + 600N 3Hz 100,000 - 600N There was no visible crack on the sample after testing.

Test Result (Cycles) 100,000

Peak deflections during the test Test Result Initial values Final values Pass 3.29 mrn 3.25 mrn Pass 4.65 mrn 4.70 mrn The peak deflections was no more than 20% of the initial values.

1. Information of sample: Material (Carbon), Mass (1 ,557 g), Frame (535 mm). 2. The rigid fork which is needed to conduct the test was provided by SGS Taiwan and rigid fork is 353 mrn in length. 3. Sample No. # 1. --- See Next Page--Note:

This document is issued by the Company subl'ect to its General Conditions of Service printed overleaf, available on re uest or accessible at · • • ·· · ·· - ttent1on IS drawn to and for electronic format documents, subject o Terms and Conditions for Electronic Documents at the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised tha t information contained hereon reflects the Company's findings at the time of its .Intervention only and withil) th~ llm1ts of Ghent's instructions, if any. The Company's sole responsibility is to its Cli~nt and this docu.ment does not exonerate ~Jarties to a transaction from exerCISing all the1r nghts and obhgat1ons under the transaction documents. Th1s document cannot be reproduced except 1n full, w1thout pnor written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results Q shown 1n th1s lest report refer only to the sample(s) tested.

35 9 331

f:; JJ\';It~#~Uli~;IJ *'~ .ij

127, Wu Kung Road, New Taipei Industrial Park, New Taipei City, Taiwan I t 1886·2) 2299 3279 f 1886·2) 2299-2920

mr :11:. rfr mr :!I:. A. ;t 00 !& Ji..I.~ 127tt www.sgs.tw_ __

Member of SGS Group


TEST REPORT Report No.: Page:

Mechanical & Hardgoods Laboratory

TH50159B/2014

6

OF

6

- Picture(s) -

--- End of Report ---

This document is issued by the Company sub1'ect to its General Conditions of Service printed overleaf, available on re uest or accessible at 路 s com/encrerms-and-Condltjons aspx and. for electronic format documents, subject o Terms and Conditions for Electronic Documents at 路 路 - AHention is drawn to the limitation of liability, mdemnificat1on and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company's findings at the time of its intervention only and within the limits of Client's instructions, if any. The Company's sole responsibility is to its Client and this document does not exonerate f)arties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior wriHen approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this lest report refer only to the sample(s) tested. Q

35 9 332

f; ~:lt-l!a-:H4Ul:1;r .:tf RV~ .>]

127. Wu Kung Road. New Ta1pci lndustnal Park. New Taipei City. Taiwan /SIT ;1::. rp i/f;l::..ii 1: 00 g Ji_.:L~l27*. t (886-2) 2299-3279 f (886路2) 2299-2920 www.sgs.tw Member of SGS Group

Menaggio 2014 EN14781 Test Report from SGS  

This is a document of the testing performed to EN14781 standards on the Pro-Lite Menaggio GP frame. The frame passes all tests. CDS-233 ref...

Read more
Read more
Similar to
Popular now
Just for you