Issuu on Google+

Static and Dynamic Restraints Catalog 09S


WARRANTY Bergen-Power Pipe Supports, Inc. (“Bergen-Power”) warrants to the original buyer (the “Buyer”) of products manufactured by it that all such products will be free from defects in material and workmanship for a period of one (1) year after the date of shipment when used in the manner and for the purpose recommended by Bergen-Power. Bergen-Power does not warrant goods manufactured by other parties, except to the extent that such goods are covered by a warranty to Bergen-Power. Notice of a claim for a breach of a warranty must be given to Bergen-Power within thirty (30) days after the date that the Buyer first has knowledge of an alleged breach of warranty, but in no event later than one (1) year after the date of shipment. Bergen-Power’s obligations under this Warranty are limited to its repair or replacement of those products that it determines, to its satisfaction, are defective, and it shall not be liable for any charge or expense incurred by the Buyer in repairing or replacing said products. Notwithstanding anything else contained herein to the contrary, Bergen-Power’s liability under this Warranty for defective products is limited to the net sales price of such products. The foregoing constitutes the Buyer’s sole and exclusive remedy for defective products. In the event that Bergen-Power provides engineering design or fabrication services, the Buyer’s acceptance of Bergen-Power’s design or delivery of the products shall relieve Bergen-Power of all further obligations with respect to such design and fabrication, except to the extent that Bergen-Power may otherwise expressly provide in a product warranty. In no event, shall Bergen-Power be responsible for design errors due to inaccurate or incomplete information provided by the Buyer or its representatives. Bergen-Power reserves the right to revise product design without notification. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER MATTER. IN NO EVENT AND UNDER NO CIRCUMSTANCE SHALL BERGEN-POWER BE LIABLE FOR (A) PERSONAL INJURY OR PROPERTY DAMAGES OR (B) CONSEQUENTIAL, SPECIAL OR INCIDENTAL DAMAGES, WHETHER FOR BREACH OF CONTRACT OR WARRANTY, NEGLIGENCE OR ANY OTHER TORTIOUS ACT OR OMISSION. THIS WARRANTY SHALL NOT APPLY TO PRODUCTS THAT HAVE BEEN SUBJECT TO ALTERATION OR REPAIR MADE BY A PARTY OTHER THAN BERGEN-POWER, ACCIDENT, ABUSE, OR MISUSE. THIS WARRANTY SUPERCEDES ALL CONTRARY OBLIGATIONS IMPOSED ON BERGEN-POWER BY ANY PURCHASE ORDER. The terms of this Warranty may not be modified or changed except by a writing signed by an authorized officer of Bergen-Power.


STATIC AND DYNAMIC RESTRAINTS

B

ergen-Power Pipe Supports is a complete line manufacturing and engineering organization offering pipe hangers. supports, restraints and specialty devices to support and control piping and equipment used in fossil power generating stations, petro-chemical plants and other industrial processing piping systems. In addition to our product line, representing one of the most complete in the industry, Bergen-Power provides

complete engineering and technical services, including analysis, hanger design and detailing, and other construction support programs. To provide effective distribution of our products and services, engineering and sales offices are maintained in major cities throughout the continental United States.

INDEX Figure No.

Page

Introduction ..............................................2 Structural Attachment 1000 ..........................................................3 Rigid Strut Assemblies 2015 ..........................................................4 2250 ..........................................................5 2252 ..........................................................6 Vibration Check – Sway braces Introduction ..............................................7 2300 ..........................................................7 2301 ..........................................................8 2302 ..........................................................8 2303 ..........................................................9 2304 ........................................................10 2305 ........................................................10 Sway Brace Pipe Clamp 6180 ........................................................11 Hydraulic Shock and Sway Arrestors Introduction ............................................12 2525 ........................................................13 2530 ........................................................14

GENERAL NOTES Outline dimensions and data shown in this catalog are for reference only and are not intended for inspection purposes. Designs and dimensions are subject to change without notice. All hanger products shown herein are manufactured in accordance with industry standards and are for installation and service as described. When used for other purposes or in ways other than those for which designed and manufactured, Bergen-Power cannot be held responsible for product failure, injuries, or property damage. Cataloged products meet requirements of MSS-SP-58 and MSS-SP-69. Maximum rated loads for hangers are based on a safety factor applicable to the codes listed in this catalog or the allowable stresses specified in ASME B31.1, ASME B31.3, and MSS-SP-58.

Restraint Yoke Clamp 6175 ........................................................15 Restraint Pipe Clamp 6202 ........................................................17 6222 (Alloy) ...........................................17 Off-axis Restraint Pipe Clamp 6252 ........................................................19 Restraint Riser Clamp 6280 ........................................................21 6281 (Alloy) ...........................................21 Welding Lug Attachment 6410 ........................................................22 Typical Arrangements ............................24

1


STATIC AND DYNAMIC RESTRAINTS

INTRODUCTION Bergen-Power markets the widest selection of restraint assemblies and devices which allows the designer to select devices technically and economically suited for the specific application by type, size and configuration. Bergen-Power restraint systems now cover a broader range of load ratings and allow greater flexibility in field adjustment. High precision steel ball bushings and pins are now standard components throughout the line. Also included is a new series of restraint yoke clamps. Bergen-Power hydraulic snubbers have also been improved and are available with options to better suit the different conditions the application requires.

SPECIFICATIONS All Bergen-Power restraints are designed to meet requirements of: Manufacturers Standardization Society SP-58, Manufacturers Standardization Society SP-69 and ASME Code for Pressure Piping ASME B31.1 and Process Piping ASME B31.3. Units meeting the requirements of the ASME Boiler and Pressure Vessel Code, Section III are also available in accordance with Bergen-Power load capacity data sheets.

RIGID STRUT ASSEMBLIES RECOMMENDED SERVICE: Used to restrain movement of piping in one direction. Movement due to thermal expansion in other directions should be evaluated. STANDARD DESIGN FEATURES: • Designed to restrain tensile and/or compressive forces. • Tight fitting connections allow positive control of piping systems. • Spherical, self-aligning ball bushing at both ends of the strut allow for ± 5° of angular motion or misalignment. • Can be installed in any spatial orientation. • Field adjustment is available in all assemblies. • All welding work required in the field is recommended to be fillet welds. • Paint — Standard primer finish.

HYDRAULIC SNUBBER ASSEMBLIES GENERAL APPLICATION: Used for the control and protection of piping and equipment subject to shock (impulse) loading and swaying (cyclic) conditions. Its use transfers any imposed forces on the piping or equipment directly to the building structure at the instant of shock occurrence, while at all other times allowing free unrestricted movement through its normal operating range. SPECIFIC APPLICATIONS: • Earthquake protection. • To prevent damage by wind in outdoor installations. • Employed at points in piping systems subject to shock loadings generated by quick closing valves, water hammer, relief valve reaction or other applied shock loads. STANDARD DESIGN FEATURES: • Piping and/or equipment movement is controlled by tamper-proof dual stage flow control poppets designed with self-cleaning orifices. • Furnished as a complete, compact, and efficient unit, ready for immediate use. • Manifold configuration requiring no external piping. • Spherical, self-aligning ball bushings allow for ± 5° of angular motion or misalignment. • Pressurized hydraulic reservoir allows mounting in any spatial orientation. • Virtually no resistance to normal thermal movements of the piping. • Paint — standard primer finish. • Large restraining forces compared to size. • Functions in restraining tension and compression. • Stroke determination is made from built-in-datum point located on piston rod wrench flats. • Fluid Level Indicator — Provides concise determination of exact fluid level in the unit, thereby eliminating estimate of reserve fluid level. OPTIONAL DESIGN FEATURES: • Remote Reservoir Mounting – The snubber’s pressurized reservoir can be remotely mounted for snubber locations that are difficult to reach. • Integral Relief Valve — A non-adjustable valve, which is factory preset at 133%, or 200% of rated load. • Protective Boot – Installed over the piston rod for protection in corrosive and/or dusty areas. • Rigid Strut Application — When no thermal growth is anticipated after lock-up an optional poppet valve, without bleed, is furnished. Must be ordered with optional integral relief valve. For information concerning Bergen-Power snubbers and snubber assemblies please contact your local Bergen-Power Pipe Supports sales office.

2


STATIC AND DYNAMIC RESTRAINTS

STRUCTURAL ATTACHMENT Figure 1000 Size Range: 700 through 130,000 pounds ( 3,114 N  through 578,240 N) load. Material: Carbon steel except load pin which is stainless steel. Service: For attachment of struts to structures. Maximum Temperature.: 350°F (177°C) for the rated loads shown. Features: Can be used as a second end attachment. Used With: Bergen‐Power Figure Numbers 2015, 2250, 2252, 2525, 2530. Ordering: Specify Figure Number and size. For Metric applications specify Figure M1000 and size. NOTE: This product is designed to function with a  10° cone of action, and a 90° arc of loading.  Load‐ ing beyond this cone or arc is not recommended.

FIGURE 1000 ‐ STRUCTURAL ATTACHMENT SIZE

LOAD

E

G

L

N

P

R

T

W

Weight

.7 .7 1.5 1.5 4 4 7 7 12 12 25 25 35 35 60 60 80 80 130 130

700 3114 1,500 6673 4,000 17794 7,000 31139 12,000 53381 25,000 111210 35,000 155694 60,000 266904 80,000 355872 130,000 578292

1 7/8 48 2 1/4 57 2 1/4 57 2 7/8 73 2 7/8 73 3 7/8 98 4 1/4 108 5 5/8 143 6 1/4 159 8 1/2 216

1/2 13 5/8 16 5/8 16 7/8 22 7/8 22 1 3/8 35 1 1/2 38 1 11/16 43 1 13/16 46 2  1/16 52

1 1/8 29 1 1/2 38 1 1/2 38 3 1/2 89 3 1/2 89 5 127 5 3/4 146 7 1/4 184 9 1/4 235 11 5/8 295

9/16 14 3/4 19 3/4 19 1 1/2 38 1 1/2 38 2 1/8 54 2 3/8 60 3 76 3 5/8 92 4 5/8 117

3/8 10 1/2 13 1/2 13 3/4 19 3/4 19 1 25 1 1/4 32 1 1/2 38 1 3/4 44 2 1/2 64

1/2 13 3/4 19 3/4 19 1 25 1 25 1 1/2 38 1 3/4 44 2 1/4 57 2 1/2 64 3 1/4 83

1/2 13 1/2 13 1/2 13 3/4 19 3/4 19 1 25 1 1/4 32 1 1/2 38 1 3/4 44 1 3/4 44

1 1/2 38 1 3/4 44 1 3/4 44 3 1/4 83 3 1/4 83 4 1/4 108 5 127 6 152 7 3/4 197 8 7/8 225

0.50 0.23 1.0 0.5 1.0 0.5 4.0 1.8 4.0 1.8 10 4.5 18 8.2 36 16 76 34 125 57

DIMENSIONS INCHES MILLIMETERS

TEMPERATURE FAHRENHEIT CELSUIS

LOADS POUNDS NEWTONS

WEIGHT POUNDS KILOGRAMS

TORQUE INCH‐POUNDS NEWTON‐METERS

3


STATIC AND DYNAMIC RESTRAINTS

LIGHT DUTY  RIGID ROD STRUT Figure 2015 Size Range: 700 to 4,000 pounds ( 3,114 N to  17,792 N ) load. Material: Carbon steel except load pin which is  stainless steel. Service: For rigid restraint applications where  short pin to pin dimensions are required. Installation: Securely fasten end bracket to struc‐ ture.  Screw rod into paddles and adjust for the desired overall length.  Fasten strut to pipe attach‐ ment (in place).  After all minor adjustments are  made the unit is locked by tightening the hex nut against the paddle. NOTE: Rods should be visible in paddle sight holes to insure proper thread engagement. Field Adjustment: Plus or minus 1½ inch (38 mm). Used With: Bergen‐Power Figures 6175,6202, 6222, 6252. Ordering: Specify figure number, size, strut length  (pin to pin length) and customer mark number (if any).  Restraint attachments must be ordered sepa‐ rately.  For Metric applications specify Figure M2015.

FIGURE 2015‐ LIGHT DUTY RIGID ROD STRUT

4

SIZE .7 .7 1.5 1.5 4 4

LOAD 700 3114 1,500 6673 4,000 17794

DIMENSIONS INCHES MILLIMETERS

TEMPERATURE FAHRENHEIT CELSUIS

P TO P MIN. MAX. 10 3/4 33 273 838 10 3/4 33 273 838 13 1/4 36 337 914

LOADS POUNDS NEWTONS

WEIGHT POUNDS KILOGRAMS

A

E

P

3/4 19 3/4 19 1 25

1 7/8 48 2 1/4 57 2 1/4 57

3/8 10 1/2 13 1/2 13

TORQUE INCH‐POUNDS NEWTON‐METERS

R

S

1 1 1/2 25 38 1 1/8 1 1/2 29 38 1 1/4 1 3/4 32 44

T 1/2 13 5/8 16 5/8 16

WGT @ MIN.  P TO P 6 2.7 9 4.1 12 5.4

TORQUE (Q) (NOMINAL) 15 20 15 20 35 47


STATIC AND DYNAMIC RESTRAINTS

ADJUSTABLE RIGID STRUT Figure 2250 Size Range: 700 through 130,000 pounds ( 3,114 N  through 578,240 N) load. Material: Carbon steel except load pin which is stainless steel. Service: For rigid restraint applications allowing the greatest amount of field adjustment without field  welding. Installation: Securely fasten end bracket to struc‐ ture.  Attach strut paddle to end bracket.  Adjust strut for the desired overall length.  Fasten strut to pipe  attachment (in place).  After all minor adjustments are  made, the unit is locked by tightening the hex nuts  against the extension piece. NOTE: Rods should be visible in the sight holes at  each end of the strut to assure proper thread engage‐ ment.  Special lengths or other increments available  upon request. FIELD ADJUSTMENT: Plus or minus two inches (51 mm) (minimum). Used With: Bergen‐Power Figure Numbers 6175, 6202, 6222, 6252. Ordering: Specify figure number, size, strut length  (pin to pin length) and customer mark number (if  any).  For Metric applications specify Figure M2250.

                                                  

                                                                                                                                   

FIGURE 2250 ADJUSTABLE RIGID STRUT SIZE

 LOAD

.7 .7 1.5 1.5 4 4 7 7 12 12 25 25 35 35 60 60 80 80 130 130

700 3114 1,500 6673 4,000 17794 7,000 31139 12,000 53381 25,000 111210 35,000 155694 60,000 266904 80,000 355872 130,000 578292

P TO P MIN. 20 508 20 508 26 660 26 660 26 660 28 711 32 813 34 864 38 965 44 1118

MAX. 112 2844.8 112 2845 120 3048 120 3048 120 3048 120 3048 120 3048 120 3048 120 3048 120 3048

DIMENSIONS TEMPERATURE LOADS WEIGHT INCHES FAHRENHEIT POUNDS POUNDS MILLIMETERS CELSUIS NEWTONS KILOGRAMS

PIPE SIZE

E

P

R

S

T

1 7/8 48 2 1/4 57 2 1/4 57 2 7/8 73 2 7/8 73 3 7/8 98 4 1/4 108 5 5/8 143 6 1/4 159 8 1/2 216

3/8 10 1/2 13 1/2 13 3/4 19 3/4 19 1 25 1 1/4 32 1 1/2 38 1 3/4 44 2 1/2 64

1 25 1 1/8 29 1 1/4 32 2 51 2 51 2 5/8 67 2 5/8 67 3 5/8 92 4 1/8 105 6 152

1 1/2 38 1 1/2 38 1 3/4 44 2 1/2 64 2 1/2 64 3 76 3 1/2 89 3 1/2 89 4 102 5 1/4 133

1/2 13 5/8 16 5/8 16 7/8 22 7/8 22 1  3/8 35 1  1/2 38 1 11/16 43 1 13/16 46 2  1/16 52

D 1 1/2 40 1 1/2 40 2 50 2 1/2 65 2 1/2 65 3 80 3 1/2 90 5 125 6 150 8 200

S/40 S/40 S/40 S/40 S/80 S/80 S/80 S/80 S/80 S/80 S/80 S/80 S/80 S/80 S/80 S/80 S/80 S/80 S/80 S/80

W 2252 1/8 3 1/8 3 1/8 3 1/4 6 1/4 6 1/4 6 1/4 6 3/8 10 3/8 10 1/2 13

WGT. @ MIN. P TO P TORQUE (Q) (APPROX.) (NOMINAL) 8 15 4 20 8 15 4 20 15 35 7 47 32 100 15 136 32 100 15 136 61 100 28 136 92 100 42 136 181 100 82 136 296 100 134 136 560 100 254 136

TORQUE INCH‐POUNDS NEWTON‐METERS

5


STATIC AND DYNAMIC RESTRAINTS

FIELD WELDED ADJUSTABLE  RIGID STRUT Figure 2252 Size Range: 700 through 130,000 pounds ( 3,114 N  through 578,240 N) load. Material: Carbon steel except load pin which is stainless steel. Service: For rigid restraint applications where pin  to pin dimension is to be determined in the field. All struts will be shipped at maximum pin to pin  dimension. Installation: Determine pin to pin dimension, cut  strut tube to required length and weld adapter end to strut.  Securely fasten end bracket to structure.  Adjust strut to desired overall length.  Fasten strut to pipe  attachment (in place).  After all minor adjustments are made, the unit is locked by tightening the hex  nuts against the extension piece. Note: Rods should be visible in the sight holes at  each end of the strut to assure proper thread engage‐ ment.  One end shipped loose for field welding. Field Adjustment: Plus or minus four inches  (102 mm) after final welding.

Note: For sizes and dimensions refer to Figure 2250 on page 5.  For sizes 60 thru 130 insert field weld adapter into 1" pipe and weld.

Ordering: Specify part number, size, and customer  d f b d mark number (if any).  For Metric applications specify  Figure M2252.

DIMENSIONS INCHES MILLIMETERS

6

TEMPERATURE FAHRENHEIT CELSUIS

LOADS POUNDS NEWTONS

WEIGHT POUNDS KILOGRAMS

TORQUE INCH‐POUNDS NEWTON‐METERS


STATIC AND DYNAMIC RESTRAINTS

 

VIBRATION CHECK‐SWAY BRACES Bergen‐Power Pipe Supports has designed its units into six  sizes, based on past experience, relating to specific pipe  sizes.  In general, we recommend the use of these sizes. Size Range: Preloads from 60 to 2,000 pounds ( 267 N to  8,896 N) up to maximum forces of 240 to 8,000 pounds ( 1,068 N to 35, 584 N). Service: For controlling vibration, to prevent externally  caused pipe sway, as an energy resisting device to oppose  shock forces and as a guide or restraint to control pipe line  movements. Temperature: 350°F (177 °C) for all components except  pipe clamp and temperature effect on spring coil. Features:  •     Compact and suitable for use in a confined space. •     Each size has 3” (76mm) of travel in either direction. •     All steel construction to protect the spring against            damage and weather conditions. •     Nameplate and movement indicator plate are anti‐           corrosive.  These plates are mechanically fastened           to prevent accidental removal. •     Paint — standard primer finish. •     Rod coupling allows for field adjustment. Optional Feature: Corrosion Resistant — available for  protection against moderate corrosive conditions or severe  weather.  The unit is galvanized, per ASTM A‐153, except  the spring which is neoprene coated.  The final closure weld  at time of assembly is metalized at time of assembly is metalized.

Specifications: All Bergen‐Power Pipe Support Vibration  Check‐Sway Braces are designed to meet the requirement of: Manufacturers Standardization Society SP‐58  Manufacturers Standardization Society SP‐69,  and ASME Code for Pressure Piping ASME B31.1 and ASME B31.3. Type Selection: Specify a Figure 2303 where adjustability  of the preload is desired, in most other cases a Figure  2300 is usually sufficient. Size Selection: The size of the vibration check‐sway brace  is determined by calculating the amount of resistive force required by the sway brace to overcome the inertia force of  the vibrating object.  This is done by taking into considera‐ tion the mass, amplitude, frequency and angle of approach of the sway brace from the axis of movement. How To Size Assemblies: The Figures 2301 and 2304  assemblies are recommended where the pin to pin dimen‐ sions are small.  For assemblies with large pin to pin dimen‐ sions, use the Figure 2302 or 2305 assemblies.  Refer to the  individual assemblies for maximum lengths. Final Setting: The sway brace should be in the neutral  (zero force) position when the system is HOT and operat‐ ing.  If not, the rod coupling must be turned to readjust to  the neutral position. Ordering: Specify figure number, size, pipe size, preload a and length (pin to pin length), customer mark number (if  any).  Pipe clamp, Figure 6180, must be ordered separately.  For Metric applications specify Figures M2300 M2301 For Metric applications specify Figures M2300, M2301,  M2302, M2303, M2304, M2305.

SINGLE ADJUSTMENT  SWAY BRACE Figure 2300

FIGURE 2300 ‐ SINGLE ADJUSTMENT SWAY BRACE RATED LOAD SPRING  Size A INITIAL  MAX.  RATE LOAD LOAD 1 60 240 60 lbs./in. 3/4 1 267 1068 11 N/mm 19 2 175 700 175 lbs./in. 1 2 778 3114 31 N/mm 25 3 500 2000 500 lbs./in. 1 3 2224 8896 88 N/mm 25 4 1,000 4000 1000 lbs./in. 1 1/4 4 4448 17793 175 N/mm 32 5 1,500 6000 1500 lbs./in. 1 1/2 5 6672 26689 263 N/mm 38 6 2,000 8000 2000 lbs./in. 1 1/2 6 8896 35586 350 N/mm 38

E

H

J

L

W

12 1/4 311 13 1/8 333 17 7/8 454 17 1/8 435 19 3/8 492 21 1/4 540

1 1/2 38 1 3/4 44 1 3/4 44 2 51 2 1/2 64 2 1/2 64

1 25 1 1/4 32 1 1/4 32 1 1/2 38 2 51 2 51

8 5/8 219 9 229 13 3/4 349 12 5/8 321 13 7/8 352 15 3/4 400

4 3/8 111 4 3/8 111 4 3/8 111 6  1/2  165 6  1/2  165 6  1/2  165

LOADS POUNDS NEWTONS

WEIGHT POUNDS KILOGRAMS

NOTES:  1) Length adjustment is 1‐1/2" (38mm) in either direction when installed in an assembly.                2) Each size has 3" (76mm) travel in either direction.

DIMENSIONS TEMPERATURE INCHES FAHRENHEIT MILLIMETERS CELSUIS

TORQUE INCH‐POUNDS NEWTON‐METERS

7


STATIC AND DYNAMIC RESTRAINTS

SINGLE ADJUSTMENT SWAY BRACE ASSEMBLIES Figure 2301

Figure 2302

FIGURE 2301, 2302 ‐ SINGLE ADJUSTMENT SWAY BRACE ASSEMBLIES FIGURE 2301, 2302 SIZE 1 1 2 2 3 3 4 4 5 5 6 6

INCHES/MM FIGURE 2300† SIZE 1 1 2 2 3 3 4 4 5 5 6 6

E

E1

E2

12 1/4 311 13 1/8 333 17 7/8 454 17 1/8 435 19 3/8 492 21 1/4 540

18 1/2 470 19 5/8 498 24 3/8 619 24 1/8 613 27 1/8 689 29     737

2 1/2 64 3 76 3 76 3 76 3 76 3 76

* Minimum P to P for Part 2302 is maximum P to P for Part 2301. † Refer to Part 2300 for rated loads, complete dimensions and notes.

DIMENSIONS INCHES MILLIMETERS

8

TEMPERATURE FAHRENHEIT CELSUIS

LOADS POUNDS NEWTONS

WEIGHT POUNDS KILOGRAMS

TORQUE INCH‐POUNDS NEWTON‐METERS

MIN. 2301       19 1/2 495 21 3/8 543 26 1/8 664 26 3/8 670 29 5/8 752 31 1/2 800

P TO P MAX. 2301     36 1/4 921 37 1/8 943 41 7/8 1064 41 1/8 1045 43 3/8 1102 45 1/4 1149

MAX.* 2302     61     1549 69     1753 74     1880 84 2134 100 2540 102     2591

W1 1/8 3 1/8 3 1/8 3  3/16 5 1/4 6 1/4 6


STATIC AND DYNAMIC RESTRAINTS

DOUBLE ADJUSTMENT SWAY BRACE Figure 2303 Preload Adjustment:  Turn the adjuster nut  on the structural  attachment end until  the desired preload is  attained.  Turn the compression nut until  it takes up the slack.   Lock in position.   Note that the indicat‐ ed deflection must be  greater than the ther‐ mal movement. FIGURE 2303‐ DOUBLE ADJUSTMENT SWAY BRACE ASSEMBLY RATED LOAD SPRING INITIAL MAX. RATE LOAD LOAD SIZE A 1 60 240     60     lbs./in. 3/4 1 267 1068 11 N/mm 19 2 175 700     175     lbs./in. 1     2 778 3114 31 N/mm 25 3 500 2000     500     lbs./in. 1     3 2224 8896 88 N/mm 25 4 1,000 4000     1000     lbs./in. 1 1/4 4 4448 17793 175 N/mm 32 5 1,500 6000     1500     lbs./in. 1 1/2 5 6672 26689 263 N/mm 38 6 2,000 8000     2000     lbs./in. 1 1/2 6 8896 35586 350 N/mm 38

E 17 5/8 448 19 1/4 489 24     610 24     610 27 3/8 695 29 1/4 743

H 4 5/8 117 5 1/8 130 5 1/8 130 5 5/8 143 6 1/4 159 6 1/4 159

J 1     25 1 1/4 32 1 1/4 32 1 1/2 38 1 3/4 44 1 3/4 44

L 9 1/2 241 10     254 14 3/4 375 13 3/4 349 15 5/8 397 17 1/2 445

W 4 3/8 111 4 3/8 111 4 3/8 111 6 1/2 165 6 1/2 165 6 1/2 165

NOTES:   1) Length adjustment is 1‐1/2" (38mm) in either direction when installed in an assembly.                 2) Each size has 3" (76mm) travel in either direction.                 3) Either of the two forces is adjustable up to the maximum rated load.

DIMENSIONS TEMPERATURE INCHES FAHRENHEIT MILLIMETERS CELSUIS

LOADS POUNDS NEWTONS

WEIGHT TORQUE POUNDS INCH‐POUNDS KILOGRAMS NEWTON‐METERS

9


STATIC AND DYNAMIC RESTRAINTS

DOUBLE ADJUSTMENT SWAY BRACE ASSEMBLIES Figure 2304

Figure 2305

FIGURE 2304, 2305 ‐ DOUBLE ADJUSTMENT SWAY BRACE ASSEMBLIES FIGURE 2304, 2305 SIZE 1 1 2 2 3 3 4 4 5 5 6 6

INCHES/MM FIGURE 2303† SIZE 1 1 2 2 3 3 4 4 5 5 6 6

E 17 5/8 448 19 1/4 489 24     610 24     610 27 3/8 695 29 1/4 743

E1 23 5/8 600 25 3/4 654 30 1/2 775 31     787 35 1/8 892 37     940

E2 2 1/2 64 3 76 3 76 3 76 3 76 3 76

* Minimum P to P for Part 2305 is maximum P to P for Part 2304. † Refer to Part 2303 for rated loads, complete dimensions and notes.

DIMENSIONS INCHES MILLIMETERS

10

TEMPERATURE FAHRENHEIT CELSUIS

LOADS POUNDS NEWTONS

WEIGHT POUNDS KILOGRAMS

TORQUE INCH‐POUNDS NEWTON‐METERS

MIN. 2304       24 7/8 632 27 1/2 699 32 1/4 819 33 1/4 845 37 5/8 956 39 1/2 1003

P TO P MAX. 2304     41 5/8 1057 43 1/4 1099 48     1219 48     1219 51 3/8 1305 57 1/4 1454

MAX.* 2305     66     1676 75     1905 80     2032 91 2311 108 2743 110     2794

W1 1/8 3 1/8 3 1/8 3  3/16 5 1/4 6 1/4 6


STATIC AND DYNAMIC RESTRAINTS

SWAY BRACE PIPE CLAMP Figure 6180 Size Range: 2 through 24 inches (50 mm to 600 mm). Material: Carbon Steel Finish: Plain Service: For use with our standard line of sway brace . assemblies only, in the control of vibration and shock  loading. Maximum Temperature: 650ºF (343ºC) for rated  loads shown. Features: Tight fitting load pin. Size Selection: See the chart shown below to match  the appropriate clamp to the desired sway brace  assembly. Ordering: Specify figure number and pipe size.   For Metric applications specify Figure M6180.

FIGURE 6180 ‐ SWAY BRACE PIPE CLAMP ASSEMBLY SIZE

1

PIPE SIZE 2 50 2 1/2 65 3 80 3 1/2 90

E3

ASSEMBLY SIZE

5 1/8 130 5 1/2 140 5 15/16 151 6  3/16 157

2

PIPE SIZE 4 100 5     125 6 150 8     200

E3 6 1/2 165 7     178 8  5/8  219 9  9/16 243

ASSEMBLY SIZE

3

PIPE SIZE 10 250 12     300 14 350 16     400

E3 10 5/8 270 11 7/8 302 13       330 13 13/16 351

ASSEMBLY SIZE

4*

PIPE SIZE 18 450 20     500 22 550 24     600

E3 14 7/8 378 16 1/4 413 17  1/8  435 18  1/16 459

* Sizes 5 and 6 as specified by customer.

DIMENSIONS TEMPERATURE INCHES FAHRENHEIT MILLIMETERS CELSUIS

LOADS POUNDS NEWTONS

WEIGHT POUNDS KILOGRAMS

TORQUE INCH‐POUNDS NEWTON‐METERS

11


STATIC AND DYNAMIC RESTRAINTS

SHORT STRUT HYDRAULIC SNUBBER Figure 2525 Size Range: Available in seven sizes from 3,000  to 130,000 pounds (3,114 N through 578,240 N) load and stroke lengths of 6, 12, and 18 inches  (152 mm, 305 mm, and 457 mm). Service: For dynamic restraint applications requir‐ ing the smallest overall assembly length in tight fit  applications. Piston Rod Setting: The factory will preset and  clamp the piston rod at the proper cold installing  stroke position.  Unless specified otherwise, this setting will position the piston so that its calculat‐ ed thermal movement will straddle the mid‐stroke  position of the unit, giving equal reserve at each  end of the stroke.  See Installation Instructions to  determine or change piston rod setting. Used With: Bergen‐Power Figures 6175, 6202,  6222, 6252, 6520, 6521, 6525, 6526. Ordering: Specify figure number, size, cylinder  stroke, thermal movement and direction (tension  or compression), preset, overall assembly length  (pin to pin length), options (if any), and customer  mark number (if any).  Restraint attachments must  be ordered separately.  For Metric applications  specify Figure M2525.

                                                                                                               

FIGURE 2525 ‐ SHORT STRUT HYDRAULIC SNUBBER INCHES/MM SIZE

MAX. LOAD

3 3 10 10 20 20 30 30 50 50 70 70 130 130

3,000 13344 10,000 44480 20,000 88960 30,000 133440 50,000 222400 70,000 311360 130,000 578240

CYL.    BORE 1  1/2  38 2  1/2  64 3  1/4  83 4       102 5       127 6       152 8       203

P TO P† MIN.• 22  3/4  578 26       660 29       737 31  3/8  797 33       838 36  3/4  933 42  5/16 1075

E

H*

L•†

L1

2  1/4  5       18  1/4  4  1/2  57 127 464 114 2  7/8  6       19  3/4  6  1/4  73 152 502 159 3  7/8  6  3/8  21  3/8  7  5/8  98 162 543 194 4  1/4  8  1/2  22  1/2  8  7/8  108 216 572 225 5  5/8  10  1/4  23       10       143 260 584 254 6  1/4  11  7/8  25       11  3/4  159 302 635 298 8  1/2  16       28  7/16 13  7/8  216 406 722 352

P

R

S

T

 1/2  13  3/4  19 1       25 1  1/4  32 1  1/2  38 1  3/4  44 2  1/2  64

1  1/4  32 2       51 2  5/8  67 2  5/8  67 3  5/8  92 4  1/8  105 6       152

1  3/4  44 2  1/2  64 3       76 3  1/2  89 3  1/2  89 4       102 5  1/4  133

  5/8  16   7/8  22 1  3/8  35 1  1/2  38 1 11/16 43 1 13/16 46 2  1/16 52

WGT.•      PRESET (APPROX.) MIN. MAX.•   3/4  6  3/4  35 19 171 16   3/4  6  3/4  70 19 171 32   3/4  6  3/4  125 19 171 57   3/4  6  3/4  155 19 171 70   3/4  6  3/4  255 19 171 116   3/4  6  3/4  410 19 171 186   3/4  6  3/4  805 19 171 365

† Unit length fully retracted. •Dimensions shown are for 6"/152mm stroke unit.   For 12"/304mm and 18"/457mm stroke units add stroke difference. * Envelope radius.

 

DIMENSIONS INCHES MILLIMETERS

TEMPERATURE FAHRENHEIT CELSUIS

LOADS POUNDS NEWTONS

WEIGHT POUNDS KILOGRAMS

TORQUE INCH‐POUNDS NEWTON‐METERS

13


STATIC AND DYNAMIC RESTRAINTS

ADJUSTABLE STRUT HYDRAULIC SNUBBER Figure 2530 SIZE RANGE: Available in seven sizes from 3,000 to 130,000  pounds ( 3,114 N through 578,240 N) and stroke lengths of  6, 12, and 18 inches (152 mm, 305 mm, and 457 mm). SERVICE: For dynamic restraint applications allowing the  greatest amount of field adjustment or where the exact  overall length must be determined on‐site. USED WITH: Bergen‐Power Figures 6175, 6202, 6222,  6252, 6520, 6521, 6525, 6526.

ORDERING: Specify figure number, size, cylinder stroke,  thermal movement and direction (tension or compression),  preset, overall assembly length (pin to pin length), options  (if any), and customer mark number (if any).  Restraint  attachments must be ordered separately.  For Metric  applications specify Figure M2530.

FIGURE 2530 ‐ SHORT STRUT HYDRAULIC SNUBBER SIZE

MAX. LOAD

3 3 10 10 20 20 30 30 50 50 70 70 130 130

3,000 13344 10,000 44480 20,000 88960 30,000 133440 50,000 222400 70,000 311360 130,000 578240

INCHES/MM P TO P† E MAX. MIN.c 33  3/8  64       15 1/8 848 1626 384 36  7/8  88       17 1/8 937 2235 435 40  1/8  106       18 3/4 1019 2692 476 42  7/8  109       20 3/8 1089 2769 518 45  3/4  178       22 3/4 1162 4521 578 50  1/4  211       25 1/4 1276 5359 641 57 9/16 232       29 1/8 1462 5893 740

PIPE SIZE 2       50 2  1/2  65 3       80 3  1/2  90 5       125 6       150 8       200

For Dimensions not given refer to Figure 2525. † Unit length fully retracted. • Weight shown is for minimum P to P and 6"(152mm) stroke unit. cDimensions shown are for 6"/152mm stroke unit.   For 12"(304mm) and 18" (457mm) stroke units add stroke difference. DIMENSIONS INCHES MILLIMETERS

14

TEMPERATURE FAHRENHEIT CELSUIS

LOADS POUNDS NEWTONS

WEIGHT POUNDS KILOGRAMS

TORQUE INCH‐POUNDS NEWTON‐METERS

S/80 S/80 S/80 S/80 S/80 S/80 S/80 S/80 S/80 S/80 S/80 S/80 S/80 S/80

WEIGHT  (APPROX.) •

TORQUE  (NOMINAL)

40       18 75       34 130       59 200       91 330       150 530       240 1050       476

35       47 100       136 100       136 100       136 100       136 100       136 100       136


PIPE CLAMPS AND ATTACHMENTS

ON‐AXIS RESTRAINT YOKE CLAMPS

 

Figure 6175 Size Range: 700 to 130,000 pounds ( 3,114 N  through 578,240 N) load. Material: Carbon steel except U‐bolt which is  alloy steel, and load pin which is stainless   steel. Finish: Plain Max. Temp.: 650ºF (343ºC). Service: For non‐integral on‐axis attachment to  the piping system in restraint applications. Used With: Bergen‐Power Figures 2015,  2250, 2252, 2525, 2530. Ordering: Specify figure number, load size  and pipe size.  Strut assembly must be ordered  separately.  For Metric applications specify  Figure M6175. NOTE: This clamp is designed to function within  a 10º cone of action, perpendicular to the pipe.   Loading beyond this cone is not recommended.

FIGURE 6175 ‐ ON‐AXIS RESTRAINT YOKE CLAMPS SIZE

MAX. LOAD

0.7 0.7 1.5 1.5 4 4 7 7 12 12 25 25 35 35 60 60 80 80 130 130

700 3,114 1,500 6,672 4,000 17,792 7,000 31,136 12,000 53,376 25,000 111,200 35,000 155,680 60,000 266,880 80,000 355,840 130,000 578,240

INCHES/MM D  3/4 19  3/4 19  3/4 19 1 1/4 32 1 1/4 32 2     51 2 1/2 64 2 1/2 64 3 1/4 83 4     102

G 1/2 13 5/8 16 5/8 16 7/8 22 7/8 22 1 3/8 35 1 1/2 38 1 11/16 43 1 13/16 46 2 1/16 52

P 3/8 10 1/2 13 1/2 13 3/4 19 3/4 19 1     25 1 1/4 32 1 1/2 38 1 3/4 44 2 1/2 64

T 1     25 1     25 1 1/4 32 1 3/4 44 1 3/4 44 2 1/2 64 3     76 3 1/2 89 6     152 8     203

TORQUE Q  (NOMINAL) 7.5 10 32     43 32     43 125     169 125     169 200     271 600     813 1000     1356 525     712 835     1132

NOTE: "E" Dimension is shown on following page.

DIMENSIONS TEMPERATURE LOADS WEIGHT INCHES FAHRENHEIT POUNDS POUNDS MILLIMETERS CELSUIS NEWTONS KILOGRAMS

TORQUE INCH‐POUNDS NEWTON‐METERS

15


PIPE CLAMPS AND ATTACHMENTS

FIGURE 6175 – ON AXIS RESTRAINT YOKE CLAMPS YOKE SIZE MAX. LOAD PIPE SIZE 3 80 4 100 5 125 6 150 8 200 10 250 12 300 14 350 16 400 18 450 20 500 24 600 30 750 36 900

.7 .7 700 3,114

1.5 1.5 1,500 6,672

7 7 7,000 31,136

12 12 12,000 53,376

25 25 25,000 111,200

35 35 35,000 155,680

60 60 60,000 266,880

80 80 80,000 355,840

130 130 130,000 578,240

E WGT. E WGT. E WGT. E WGT. E WGT. E WGT. E WGT. E WGT. E WGT. E WGT. 6 4 6 4.5 6 5 8 13 8 13 152 1.8 152 2.0 152 2.3 203 5.9 203 5.9 61⁄2 5 61⁄2 5.5 6 1⁄ 2 6 81⁄2 15 81⁄2 15 165 2.3 165 2.5 165 2.7 216 6.8 216 6.8 71⁄16 6 71⁄16 6 71⁄16 6.5 179 2.7 179 2.7 179 2.9 79⁄16 6 79⁄16 7 79⁄16 8 99⁄16 24 99⁄16 24 109⁄16 34 192 2.7 192 3.2 192 3.6 243 11 243 11 268 15 99⁄16 9 99⁄16 10 99⁄16 11 109⁄16 24 109⁄16 24 119⁄16 40 243 4.1 243 4.5 243 5.0 268 11 268 11 294 18 105⁄8 10 105⁄8 11 105⁄8 12 115⁄8 28 115⁄8 28 125⁄8 48 270 4.5 270 5.0 270 5.4 295 13 295 13 321 22 115⁄8 13 115⁄8 15 115⁄8 16 125⁄8 33 125⁄8 33 135⁄8 53 133⁄8 66 151⁄8 145 153⁄8 200 295 5.9 295 6.8 295 7.3 321 15 321 15 346 24 340 30 384 66 391 91 121⁄4 17 131⁄4 33 131⁄4 33 141⁄4 54 14 70 16 155 17 225 19 400 311 7.7 337 15 337 15 362 24 356 32 406 70 432 102 483 181 131⁄4 19 141⁄4 36 141⁄4 36 151⁄4 57 15 78 171⁄4 175 18 285 20 500 337 8.6 362 16 362 16 387 26 381 35 438 79 457 129 508 227 151⁄4 36 151⁄4 36 161⁄4 65 16 86 181⁄2 185 19 295 21 510 387 16 387 16 413 29 406 39 470 84 483 134 533 231 161⁄4 41 161⁄4 41 171⁄4 70 17 96 193⁄4 205 20 320 23 620 413 19 413 19 438 32 432 44 502 93 508 145 584 281 181⁄4 48 181⁄4 48 211⁄4 96 20 140 221⁄4 270 23 420 25 690 464 22 464 22 540 44 508 64 565 122 584 191 635 313 231⁄4 72 231⁄4 72 241⁄4 124 24 175 26 310 27 540 29 925 591 33 591 33 616 56 610 79 660 141 686 245 737 420 271⁄4 156 271⁄4 220 29 330 321⁄2 730 32 1055 692 71 692 100 737 150 826 331 813 479

DIMENSIONS TEMPERATURE INCHES FAHRENHEIT MILLIMETERS CELSIUS 16

4 4 4,000 17,792

LOADS POUNDS NEWTONS

WEIGHT TORQUE POUNDS INCH-POUNDS KILOGRAMS NEWTON-METERS


PIPE CLAMPS AND ATTACHMENTS

RESTRAINT PIPE CLAMPS Figure 6202 ‐ Carbon Steel Size range: 700 to 130,000 pounds ( 3,114 N  through 578,240 N) of load in various pipe sizes  from ¾ (20 mm) through 36 inches (900 mm). Material: Carbon steel except the load pin which is stainless steel. Service: For non‐integral on‐axis attachment to the  piping system in restraint applications. Maximum Temperature: 650ºF (343ºC)for the  rated loads shown. Features:  • Designed for use with spherical ball bushings. • Tight tolerances provide for low lost motion. • Interchangeable with a variety of Bergen‐Power       struts. Used With: Bergen‐Power figures 2015, 2250,  2252, 2525, 2530. Ordering: Specify figure number, load size, and pipe  size.  Strut attachment must be ordered separately.   For Metric applications specify Figure M6202. Installation Note: Tension bolts to remove slack,  (while maintaining dim. “G”) plus ½ turn of the  nut Then lock jam nut to full nut nut.  Then lock jam nut to full nut. NOTE: This clamp is designed to function within a  10º cone of action, perpendicular to the pipe.  Loading beyond this cone is not recommended. NOTE: Dimensions are shown on the following page.

Figure 6222 ‐ Alloy Steel Size Range: Same as 6202 adjusted for temperature. Material: Chrome molybdenum steel. Maximum Temperature: 1100ºF (593ºC). Ordering: Made special to customer order.  Please  contact your local Bergen‐Power sales office for  details.  For Metric applications specify Figure M6222. NOTE: Dimensions shown on following page do not apply.

DIMENSIONS INCHES MILLIMETERS

TEMPERATURE FAHRENHEIT CELSUIS

LOADS POUNDS NEWTONS

WEIGHT POUNDS KILOGRAMS

TORQUE INCH‐POUNDS NEWTON‐METERS

17


PIPE CLAMPS AND ATTACHMENTS

FIGURE 6202 – RESTRAINT PIPE CLAMPS LOAD SIZE MAX. LOAD PIPE SIZE E 3⁄ 4 41⁄ 4 20 108 1 41⁄2 25 114 11⁄4 43⁄4 32 121 11⁄2 43⁄4 40 121 2 5 50 127 21⁄2 53⁄4 65 146 3 6 80 152 4 7 100 178 5 71⁄2 125 191 6 8 150 203 8 91⁄2 200 241 10 11 250 279 12 300 14 350 16 400 18 450 20 500 24 600 30 750 36 900

.7 .7 700 3,114 W 11⁄2 38 11⁄2 38 11⁄2 38 11⁄2 38 11⁄ 2 38 11⁄2 38 11⁄ 2 38 11⁄ 2 38 11⁄2 38 11⁄ 2 38 2 51 2 51

1.5 1.5 1,500 6,672 WGT. E 2 41⁄4 0.9 108 2 41⁄2 0.9 114 2 43⁄4 0.9 121 2 43⁄4 0.9 121 2 5 0.9 127 3 53⁄4 1.4 146 3 6 1.4 152 3 7 1.4 178 4 71⁄2 1.8 191 4 8 1.8 203 6 91⁄2 2.7 241 7 11 3.2 279 12 305

W 2 51 2 51 2 51 2 51 2 51 2 51 2 51 2 51 2 51 2 51 2 51 2 51 2 51

4 4 4,000 17,792 WGT. E 3 1.4 3 1.4 3 1.4 3 1.4 4 1.8 4 1.8 4 73⁄4 1.8 197 7 81⁄4 3.2 210 7 83⁄4 3.2 222 8 91⁄2 3.6 241 9 101⁄2 4.1 267 11 12 5.0 305 16 13 7.3 330 14 356 15 381 16 406 17 432 19 483 23 584 26 660

7 7 7,000 31,136

W WGT. E

21⁄2 64 21⁄2 64 3 76 3 76 4 102 4 102 5 127 4 102 4 102 41⁄2 114 5 127 41⁄2 114 41⁄2 114 5 127

17 7.7 18 8.2 23 10 24 11 35 16 40 18 55 25 58 26 63 29 76 34 91 41 125 57 151 68 194 88

12 12 12,000 53,376

W WGT. E

73⁄4 5 197 127 81⁄4 5 210 127 83⁄4 41⁄2 222 114 91⁄2 41⁄2 241 114 101⁄2 41⁄2 267 114 12 5 305 127 13 5 330 127 14 5 356 127 15 5 381 127 16 5 406 127 17 5 432 127 19 6 483 152 23 6 584 152 26 6 660 152

33 73⁄4 15 197 34 81⁄4 15 210 47 83⁄4 21 222 51 91⁄2 23 241 58 101⁄2 26 267 83 12 38 305 90 13 41 330 97 14 44 356 113 15 51 381 121 16 55 406 131 17 59 432 175 19 79 483 260 23 118 584 297 26 135 660

25 25 25,000 111,200

W WGT. E

5 127 5 127 41⁄2 114 41⁄2 114 41⁄2 114 5 127 5 127 5 127 5 127 5 127 5 127 6 152 6 152 6 152

33 15 34 91⁄4 15 235 47 10 21 254 51 11 23 279 58 12 26 305 83 131⁄2 38 343 90 141⁄2 41 368 97 16 44 406 113 17 51 432 121 18 55 457 131 19 59 483 175 22 79 559 260 25 118 635 297 28 135 711

35 35 35,000 155,680

W WGT. E

5 127 5 127 5 127 5 127 5 127 5 127 5 127 5 127 6 152 6 152 5 127 5 127 7 178

90 41 97 44 105 48 113 51 125 57 136 62 170 77 182 83 232 105 252 114 280 127 338 153 516 234

12 305 131⁄2 343 141⁄2 368 16 406 17 432 18 457 19 483 22 559 25 635 28 711

60 60 60,000 266,880

W WGT. E

6 152 5 127 5 127 6 152 6 152 7 178 7 178 6 152 7 178 8 203

141 64 158 131⁄2 72 343 171 151⁄4 78 387 215 16 3⁄4 98 425 230 173⁄4 104 451 306 183⁄4 139 476 326 193⁄4 148 502 345 223⁄4 156 578 487 253⁄4 221 654 621 283⁄4 282 730

80 80 80,000 355,840

W WGT. E

6 152 7 178 7 178 7 178 7 178 7 178 8 203 9 229 10 254

130 130 130,000 578,240

W WGT. E

176 15 80 381 241 16 109 406 258 17 117 432 277 18 126 457 342 19 155 483 364 20 165 508 475 23 215 584 611 26 277 660 766 291⁄4 347 743

9 229 9 229 10 254 10 254 11 279 11 279 11 279 11 279 11 279

W WGT.

292 132 316 143 368 191⁄4 167 489 394 201⁄4 179 514 459 211⁄4 208 540 489 221⁄4 222 565 653 241⁄4 296 616 754 281⁄4 342 718 981 311⁄2 445 800

10 447 254 203 10 479 254 217 10 512 254 232 10 543 254 246 14 826 356 375 14 993 356 450 15 1224 381 555

FIGURE 6202 – RESTRAINT PIPE CLAMPS Load Size Max. Load G G D D P P

.7 .7 700 3,114 17⁄ 32 13 5⁄ 8 16 3⁄ 8 10

DIMENSIONS TEMPERATURE INCHES FAHRENHEIT MILLIMETERS CELSIUS 18

1.5 1.5 1,500 6,672 21⁄ 32 17 3⁄ 4 19 1⁄ 2 13

LOADS POUNDS NEWTONS

4 4 4,000 17,792 21⁄ 32 17 7⁄ 8 22 1⁄ 2 13

7 7 7,000 31,136 29⁄ 32 23 11⁄4 32 3⁄ 4 19

12 12 12,000 53,376 29⁄ 32 23 11⁄4 32 3⁄ 4 19

WEIGHT TORQUE POUNDS INCH-POUNDS KILOGRAMS NEWTON-METERS

25 25 25,000 111,200 17⁄16 37 21⁄4 57 1 25

35 35 35,000 155,680 117⁄32 39 25⁄8 67 11/4 32

60 60 60,000 266,880 13⁄4 44 21⁄4 57 11⁄2 38

80 80 80,000 355,840 17⁄8 48 3 76 13⁄4 44

130 130 130,000 578,240 23⁄32 53 31⁄2 89 21⁄2 64


PIPE CLAMPS AND ATTACHMENTS

OFF‐AXIS RESTRAINT PIPE CLAMP Figure 6252 Size Range: 700 to 60,000 pounds (3,114N  to 266,880 N ) of load in various pipe sizes  from 1½" (40 mm) through 36 (900 mm) inches. Material: Carbon steel except the load pin which is  stainless steel. Service: For non‐integral off‐axis attachment to the  piping system in restraint applications. Maximum Temperature: 650ºF (343ºC )for the  rated loads shown. Used With: Bergen‐Power figures 2015, 2250,  2252, 2525, 2530. Ordering: Specify figure number, load size, and pipe  size.  Strut attachment must be ordered separately.  For Metric applications specify Figure M6252. Note: This clamp is designed to function within a  10º cone of action and a 90º arc of loading.   Loading beyond the cone or arc is not recommended. Installation note: Tension bolts to remove slack,  (while maintaining dim. “G”) plus ½ turn of nut.   Then lock jam nut to full nut.  This product must  be used with shear lugs supplied by others. Note: Dimensions are shown on the following page. i i h h f ll i

                                                                                                                                    

DIMENSIONS TEMPERATURE LOADS WEIGHT TORQUE INCHES FAHRENHEIT POUNDS POUNDS INCH‐POUNDS MILLIMETERS CELSUIS NEWTONS KILOGRAMS NEWTON‐METERS

19


PIPE CLAMPS AND ATTACHMENTS

FIGURE 6252 – OFF AXIS RESTRAINT PIPE CLAMP LOAD SIZE MAX. LOAD PIPE SIZE 11⁄2 40 2 50 21⁄2 65 3 80 4 100 5 125 6 150 8 200 10 250 12 300 14 350 16 400 18 450 20 500 22 550 24 600 26 650 28 700 30 750 32 800 34 850 36 900

.7 .7 700 3,114 E 43 ⁄ 4 121 5 127 53 ⁄ 4 146 6 152 7 178 71⁄2 191 8 203 91⁄2 241 11 279 12 305 13 330 14 356

1.5 1.5 1,500 6,672

W WGT. E W 2 6 51 2.7 2 6 5 3 51 2.7 127 76 21 ⁄ 2 8 53 ⁄ 4 3 64 3.6 146 76 21⁄2 9 6 3 64 4.1 152 76 21⁄2 10 7 3 64 4.5 178 76 21⁄2 11 71⁄2 3 64 5.0 191 76 3 15 8 3 76 6.8 203 76 3 19 91⁄2 3 76 8.6 241 76 3 28 11 4 76 13 279 102 3 31 12 4 76 14 305 102 3 34 13 4 76 15 330 102 3 37 14 4 76 17 356 102 15 5 381 127 16 5 406 127

4 4 4,000 17,792 WGT. E 12 5.4 13 5.9 14 6.4 19 8.6 21 9.5 27 12 32 15 48 22 53 24 57 26 63 29 84 38 90 41

7 3⁄ 4 197 8 1⁄ 4 210 8 3⁄ 4 222 91⁄2 241 101⁄2 267 12 305 13 330 14 356 15 381 16 406 17 432 18 457 19 483 20 508 22 559 23 584 24 610 25 635 26 660

7 7 7,000 31,136

W WGT.

6 152 5 127 5 127 5 127 5 127 6 152 6 152 6 152 7 178 7 178 7 178 7 178 7 178 7 178 7 178 7 178 7 178 7 178 8 203

57 26 66 30 71 32 78 35 89 40 122 55 137 62 145 66 165 75 195 88 210 95 265 120 295 134 310 141 383 174 405 184 425 193 446 202 463 210

E

8 1⁄ 4 210 8 3⁄ 4 222 9 1⁄ 2 241 101⁄2 267 12 305 13 330 14 356 15 381 16 406 17 432 18 457 19 483 20 508 22 559 23 584 24 610 25 635 26 660

12 12 12,000 53,376

W WGT.

7 178 7 178 7 178 7 178 8 203 8 203 7 178 7 178 7 178 8 203 8 203 8 203 9 229 8 203 8 203 8 203 9 229 9 229

104 47 114 52 125 57 143 65 187 85 212 96 241 109 261 118 283 128 346 157 371 168 395 179 471 214 526 239 556 252 583 264 685 311 717 325

E

81⁄ 4 210 83⁄ 4 222 91⁄ 2 241 101⁄2 267 12 305 13 330 14 356 15 381 16 406 17 432 18 457 19 483 20 508 22 559 23 584 24 610 25 635 26 660

25 25 25,000 111,200

W WGT.

7 178 7 178 7 178 7 178 8 203 8 203 7 178 7 178 7 178 8 203 8 203 8 203 9 229 8 203 8 203 8 203 9 229 9 229

104 47 114 52 125 57 143 65 187 85 212 96 241 109 261 118 283 128 346 157 371 168 395 179 471 214 526 239 556 252 583 264 685 311 717 325

E

10 254 11 279 12 305 131⁄2 343 15 381 16 406 17 432 18 457 19 483

35 35 35,000 155,680

60 60 60,000 266,880

W WGT. E

W WGT.

9 229 8 203 9 229 10 254 11 279 11 279 12 305 12 305 12 305

13 330 14 356 15 381 15 381 15 381 15 381 16 406

199 90 224 102 281 127 354 161 437 198 465 211 549 249 591 268 632 287

13 330 14 356 151⁄2 394 16 406 17 432 18 457 191⁄2 495

430 195 511 232 610 277 642 291 695 315 746 338 861 391

22 14 865 221⁄2 16 1258 559 356 392 572 406 571

25 15 1086 251⁄2 16 1474 635 381 493 648 406 669

28 16 1327 29 16 1695 711 406 602 737 406 769

E

W

WGT.

141⁄4 362 153⁄4 400 163⁄4 425 173⁄4 451 183⁄4 476 20 508 213⁄4 552 223⁄4 578 233⁄4 603 251⁄2 648 263⁄4 679 273⁄4 705 283⁄4 730 293⁄4 756

16 406 18 457 19 483 19 483 20 508 20 508 16 406 16 406 16 406 16 406 16 406 16 406 16 406 16 406

542 246 681 309 769 349 834 378 948 430 1016 461 1143 518 1214 551 1284 582 1530 694 1624 737 1698 770 1801 817 1854 841

Sizes above and to the left of solid line are Type I. Sizes to the right and below are Type II. Load Size Max. Load G G D D P P

20

.7 .7 700 3,114 17⁄ 32 13 7⁄ 16 11 3⁄ 8 10

1.5 1.5 1,500 6,672 21⁄ 32 17 5⁄ 8 16 1⁄ 2 13

4 4 4,000 17,792 21⁄ 32 17 7⁄ 8 22 1⁄ 2 13

7 7 7,000 31,136 29⁄ 32 23 11⁄4 32 3⁄ 4 19

12 12 12,000 53,376 29⁄ 32 23 11⁄4 32 3⁄ 4 19

25 25 25,000 111,200 17/16 37 21⁄4 57 1 25

35 35 35,000 155,680 117⁄32 39 25⁄8 67 11⁄4 32

60 60 60,000 266,880 13⁄4 44 21⁄4 57 11⁄2 38


PIPE CLAMPS AND ATTACHMENTS

RESTRAINT RISER CLAMPS Figure 6280 — Carbon Steel

Figure 6281 — Alloy Steel

Material: Carbon steel except load pin which is stainless steel Finish: Plain. Maximum Temperature: 650ºF (343ºC). Service: For axial restraint of vertical or horizontal piping  where two struts are required.  Load is carried by shear lugs  which are welded to the pipe. Ordering: Specify part number, exact pipe O.D., load,  operating temperature, C‐C dimension and strut size.  Strut  assembly must be ordered separately.  For Metric applica‐ tions specify Figure M6280.

Material: Chrome molybdenum  steel except load pin  which is stainless steel. Finish: Plain. Maximum Temperature: 1100ºF (593ºC). Service: For axial restraint of vertical or horizontal pipin where two struts are required.  Load is carried by shear lugs which are welded to the pipe. Ordering: Specify part number, exact pipe O.D., load, operating temperature, C‐C dimension and strut size.   Strut assembly must be ordered separately.  For Metric applications specify Figure M6281.

                                                  

DIMENSIONS INCHES MILLIMETERS

TEMPERATURE FAHRENHEIT CELSUIS

LOADS POUNDS NEWTONS

WEIGHT POUNDS KILOGRAMS

TORQUE INCH‐POUNDS NEWTON‐METERS

21


PIPE CLAMPS AND ATTACHMENTS

WELDING LUG ATTACHMENT Figure 6410 Size Range: 700 to 60,000 pounds (3,114 N to  266,880 N) load for various pipe sizes from 1½”  (40 mm) through 36” (900 mm). Material: Carbon steel except the load pin which is  stainless steel. Service: For integral attachment to a piping system in restraint applications. Maximum Temperature: 650ºF (343ºC) for the  rated loads shown. Ordering: Specify figure number, load size, and  pipe size.  Strut assembly must be ordered separately.   For Metric applications specify Figure M6410. Note: This product is designed to function within  a 10º cone of action and a 180º arc of loading.  Load‐ ing beyond the cone or arc is not recommended. FIGURE 6410 ‐ WELDING LUG ATTACHMENT YOKE  SIZE MAX.  LOAD PIPE  SIZE 1 1/2 40 2 50 2 1/2 65 3 80 4 100 5 125 6 150 8 200 10 250 12 300 14 350 16 400 18 450 20     500 24     600 30 750 36     900

.7 .7 700 3114

1.5 1.5 1500     6672

4 4 4000 17792

E

L

W

*Ins.

Wgt.

E

L

W

*Ins.

Wgt.

E

L

W

*Ins.

Wgt.

3 3/4 95 3 3/4 95 4 1/4 108 4 1/4 108 4 3/4 121 4 3/4 121 4 3/4 121 5 1/4 133 5 1/2 140 5 1/2 140

4 3/8 111 4 3/8 111 4 7/8 124 4 7/8 124 5 3/8 137 5 3/8 137 5 3/8 137 5 7/8 149 6 1/8 156 6 1/8 156

3     76 3     76 3     76 3     76 4     102 4     102 4     102 4     102 4     102 4     102

2 7/8 73 2 7/8 73 3 3/8 86 3 3/8 86 3 7/8 98 3 7/8 98 3 7/8 98 4 3/8 111 4 5/8 117 4 5/8 117  

1.4 0.6 1.4 0.6 1.5 0.7 1.5 0.7 2 0.9 2 0.9 2 0.9 2.3 1.0 2.4 1.1 2.4 1.1

3 3/4 95 3 3/4 95 4 1/4 108 4 1/4 108 4 3/4 121 4 3/4 121 4 3/4 121 5 1/4 133 5 1/2 140 5 1/2 140

4 5/8 117 4 5/8 117 5 1/8 130 5 1/8 130 5 5/8 143 5 5/8 143 5 5/8 143 6 1/8 156 6 3/8 162 6 3/8 162

3     76 3     76 3     76 3     76 4     102 4     102 4     102 4     102 4 1/8 105 4 1/8 105

2 5/8 67 2 5/8 67 3 1/8 79 3 1/8 79 3 5/8 92 3 5/8 92 3 5/8 92 4 1/8 105 4 3/8 111 4 3/8 111

1.6 0.7 1.6 0.7 1.8 0.8 1.8 0.8 2.4 1.1 2.4 1.1 2.4 1.1 2.6 1.2 2.7 1.2 2.7 1.2

3 3/4 95 3 3/4 95 4 1/4 108 4 1/4 108 4 3/4 121 4 3/4 121 4 3/4 121 5 1/4 133 5 1/2 140 5 1/2 140 6     152 6     152

5     127 5     127 5 1/2 140 5 1/2 140 6     152 6     152 6     152 6 1/2 165 6 3/4 171 6 3/4 171 7 1/4 184 7 1/4 184

3     76 3     76 3     76 3     76 4     102 4     102 4     102 4     102 4     102 4     102 5     127 5     127

2 1/8 54 2 1/8 54 2 5/8 67 2 5/8 67 3 1/8 79 3 1/8 79 3 1/8 79 3 5/8 92 3 7/8 98 3 7/8 98 4 3/8 111 4 3/8 111

2.8 1.3 2.8 1.3 3.1 1.4 3.1 1.4 4 1.8 4 1.8 4 1.8 4.4 2.0 4.6 2.1 4.6 2.1 5.6 2.5 5.6 2.5

* Maximum insulation thickness.

DIMENSIONS INCHES MILLIMETERS

22

7 7 7000 31136

TEMPERATURE FAHRENHEIT CELSUIS

LOADS POUNDS NEWTONS

WEIGHT POUNDS KILOGRAMS

TORQUE INCH‐POUNDS NEWTON‐METERS

E

L

W

*Ins.

Wgt.

6     152 6     152 6     152 6 1/4 159 6 1/4 159 6 3/4 171 6 3/4 171 7     178 7     178 7     178 7     178 7     178 8     203 8     203

7 1/2 191 7 1/2 191 7 1/2 191 7 3/4 197 7 3/4 197 8 1/4 210 8 1/4 210 8 1/2 216 8 1/2 216 8 1/2 216 8 1/2 216 8 1/2 216 9 1/2 241 9 1/2 241

6     152 6     152 6     152 6     152 6     152 6     152 6     152 6     152 6     152 6     152 6     152 6     152 7     178 7     178

3 7/8 98 3 7/8 98 3 7/8 98 4 1/8 105 4 1/8 105 4 5/8 117 4 5/8 117 4 7/8 124 4 7/8 124 4 7/8 124 4 7/8 124 4 7/8 124 5 7/8 149 5 7/8 149

9.2 4.2 9.2 4.2 9.2 4.2 9.5 4.3 9.5 4.3 10 4.6 10 4.6 11 4.8 11 4.8 11 4.8 11 4.8 11 4.8 12 5.3 12 5.3


PIPE CLAMPS AND ATTACHMENTS

FIGURE 6410 – WELDING LUG ATTACHMENT (CONT.) YOKE SIZE MAX. LOAD PIPE SIZE 11⁄2 40 2 50 21⁄2 65 3 80 4 100 5 125 6 150 8 200 10 250 12 300 14 350 16 400 18 450 20 500 24 600 30 750 36 900

12 12 12,000 53,376

25 25 25,000 111,200

E

L

W

*INS. WGT.

6 152 6 152 6 152 61⁄4 159 61⁄4 159 63⁄4 171 63⁄4 171 7 178 7 178 7 178 7 178 7 178 8 203 8 203

71 ⁄ 2 191 71 ⁄ 2 191 71 ⁄ 2 191 73⁄4 197 73⁄4 197 81⁄4 210 81⁄4 210 81⁄2 216 81⁄2 216 81⁄2 216 81⁄2 216 81⁄2 216 91⁄2 241 91⁄2 241

6 152 6 152 6 152 6 152 6 152 6 152 6 152 6 152 6 152 6 152 6 152 6 152 7 178 7 178

37⁄8 98 37⁄8 98 37⁄8 98 41⁄8 105 41⁄8 105 45⁄8 117 45⁄8 117 47⁄8 124 47⁄8 124 47⁄8 124 47⁄8 124 47⁄8 124 57⁄8 149 57⁄8 149

9.2 4.2 9.2 4.2 9.2 4.2 9.5 4.3 9.5 4.3 10 4.6 10 4.6 11 4.8 11 4.8 11 4.8 11 4.8 11 4.8 12 5.3 12 5.3

35 35 35,000 155,680

E

L

W

*INS. WGT.

7 178 7 1⁄ 4 184 7 3⁄ 4 197 7 3⁄ 4 197 8 203 8 203 9 229 9 229 9 229 9 229 10 254 10 254 10 254

9 1⁄ 2 241 93 ⁄ 4 248 101⁄4 260 101⁄4 260 101⁄2 267 101⁄2 267 111⁄2 292 111⁄2 292 111⁄2 292 111⁄2 292 121⁄2 318 121⁄2 318 121⁄2 318

9 229 9 229 9 229 9 229 9 229 9 229 9 229 9 229 9 229 9 229 10 254 10 254 10 254

37⁄8 98 41⁄8 105 45⁄8 117 45⁄8 117 47⁄8 124 47⁄8 124 57⁄8 149 57⁄8 149 57⁄8 149 57⁄8 149 67⁄8 175 67⁄8 175 67⁄8 175

26 12 27 12 28 13 28 13 29 13 29 13 32 15 32 15 32 15 32 15 37 17 37 17 37 17

60 60 60,000 266,880

E

L

W

*INS. WGT.

7 3⁄ 4 197 8 203 8 203 9 229 9 229 9 229 9 229 10 254 10 254 10 254

103⁄4 273 11 279 11 279 12 305 12 305 12 305 12 305 13 330 13 330 13 330

10 254 10 254 10 254 10 254 10 254 10 254 10 254 12 305 12 305 12 305

4 1⁄ 8 105 4 3⁄ 8 111 4 3⁄ 8 111 53⁄8 137 53⁄8 137 53⁄8 137 53⁄8 137 6 3⁄ 8 162 6 3⁄ 8 162 6 3⁄ 8 162

39 18 40 18 40 18 44 20 44 20 44 20 44 20 54 24 54 24 54 24

E

L

W

*INS. WGT.

8 203 8 203 9 229 9 229 9 229 9 229 10 254 10 254 10 254

11 279 11 279 12 305 12 305 12 305 12 305 13 330 13 330 13 330

12 305 12 305 12 305 12 305 12 305 12 305 15 381 15 381 15 381

3 7⁄ 8 98 3 7⁄ 8 98 4 7⁄ 8 124 4 7⁄ 8 124 4 7⁄ 8 124 4 7⁄ 8 124 5 7⁄ 8 149 5 7⁄ 8 149 5 7⁄ 8 149

51 23 51 23 56 25 56 25 56 25 56 25 71 32 71 32 71 32

* Maximum insulation thickness

FIGURE 6410 – WELDING LUG ATTACHMENT SIZE MAX. LOAD G G P P R1 R1 R2 R2 T T

.7 .7 700 3,114 1⁄ 2 13 3⁄ 8 10 5⁄ 8 16

1.5 1.5 1,500 6,672 5⁄ 8 16 1⁄ 2 13 7⁄ 8 22

4 4 4,000 17,792 5⁄ 8 16 1⁄ 2 13 11⁄4 32

1⁄ 4

1⁄ 4

6

6

3⁄ 8 10

7 7 7,000 31,136 7⁄ 8 22 3⁄ 4 19 11⁄2 38 1⁄ 2 13 1⁄ 2 13

12 12 12,000 53,376 7⁄ 8 22 3⁄ 4 19 11⁄2 38 1⁄ 2 13 1⁄ 2 13

DIMENSIONS TEMPERATURE INCHES FAHRENHEIT MILLIMETERS CELSIUS

25 25 25,000 111,200 13⁄8 35 1 25 21⁄2 64 3⁄ 4 19 3⁄ 4 19

LOADS POUNDS NEWTONS

35 35 35,000 155,680 11⁄2 38 11⁄4 32 3 76 7⁄ 8 22 7⁄ 8 22

60 60 60,000 266,880 111⁄16 43 11⁄2 38 3 76 1 25 1 25

WEIGHT TORQUE POUNDS INCH-POUNDS KILOGRAMS NEWTON-METERS 23


EXECUTIVE OFFICES MASSACHUSETTS 225 Merrimac Street Woburn, MA 01801 Tel: (781) 935-9550 Fax: (781) 938-0026 e-mail: bpwoburn@bergenpower.com

MANUFACTURING PLANT PENNSYLVANIA 484 Galiffa Drive Donora Industrial Park Donora, PA 15033


Bergen-Power Restraints Catalog 09S