Page 26

â—?J codes: Application Functions Func. Code

Name Braking signal (Released timer) (Putting on Frequency) (Putting on timer) Reserved *3

Data setting range 0.0 to 5.0 s 0.0 to 25.0 Hz 0.0 to 5.0 s -

Data Default setting copy*2

Min.

Unit

0.1 0.1 0.1 -

Hz s s -

Min.

Unit

1 -

-

Y Y

1 0

0.1 -

s -

Y Y

2.0 3

-

-

Y

0

-

-

Y

0

-

-

Y

0

1

s

Y

0

0.01 -

s -

Y Y

0.01 1

1 -

-

Y Y

1 0

0.1 -

s -

Y Y

2.0 3

-

-

Y

0

-

-

Y

0

-

-

Y

0

1

s

Y

0

0.01 -

s -

Y Y

0.01 0

-

-

Y

0

-

-

N

0

Y Y Y -

1.0 1.0 1.0 -

to

â—?y codes: Link Functions Name

Data setting range

RS485 Communication P (Station address) 1 to 255 (Mode selection on no response error) 0 : Immediately trip and alarm 1 : Trip and alarm after running for the period specified by timer y03 2 : Retry during the period specified by timer y03. If retry fails, trip and alarm . If it succeeds, continue to run. 3 : Continue to run (Timer) 0.0 to 60.0 s (Baud rate) 0 : 2,400 bps 1 : 4,800 bps 2 : 9,600 bps 3 : 19,200 bps 4 : 38,400 bps (Data length) 0 : 8 bits 1 : 7 bits (Parity check) 0 : None(With 2 stop bits for RTU) 1 : Even parity(With 1 stop bit for RTU) 2 : Odd parity(With 1 stop bit for RTU) 3 : None(With 1 stop bit for RTU) (Stop bits) 0 : 2 bits 1 : 1 bit (No-response error detection time) 0 : No detection 1 to 60 s (Response interval) 0.00 to 1.00 s (Protocol selection) 0 : Modbus RTU protocol 1 : FRENIC Loader protocol (SX protocol) 2 : Fuji general-purpose inverter protocol RS485 Communication Q (Station address) 1 to 255 (Mode selection on no response error) 0 : Immediately trip and alarm 1 : Trip and alarm after running for the period specified by timer y03 2 : Retry during the period specified by timer y03. If retry fails, trip and alarm . If it succeeds, continue to run 3 : Continue to run (Timer) 0.0 to 60.0 s (Baud rate) 0 : 2,400 bps 1 : 4,800 bps 2 : 9,600 bps 3 : 19,200 bps 4 : 38,400 bps (Data length) 0 : 8 bits 1 : 7 bits (Parity check) 0 : None(With 2 stop bits for RTU) 1 : Even parity(With 1 stop bit for RTU) 2 : Odd parity(With 1 stop bit for RTU) 3 : None(With 1 stop bit for RTU) (Stop bits) 0 : 2 bits 1 : 1 bit (No-response error detection time) 0 : No detection 1 to 60 s (Response interval) 0.00 to 1.00 s (Protocol selection) 0 : Modbus RTU protocol 2 : Fuji general-purpose inverter protocol Bus Link Function (Mode selection) Frequency command Run command 0 : Follow H30 data Follow H30 data 1 : Via field bus option Follow H30 data 2 : Follow H30 data Via field bus option 3 : Via field bus option Via field bus option Loader Link Function (Mode selection) Frequency command Run command 0 : Follow H30 and y98 data Follow H30 and y98 data 1 : Via RS485 link (Loader) Follow H30 and y98 data 2 : Follow H30 and y98 data Via RS485 link (Loader) 3 : Via RS485 link (Loader) Via RS485 link (Loader) *1 When you make settings from the keypad, the incremental unit is restricted by the number of digits that the LED monitor can display. (Example) If the setting range is from -200.00 to 200.00, the incremental unit is as follows: "1" for -200 to -100, "0.1" for -99.9 to -10.0, "0.01" for -9.99 to -0.01, "0.01" for 0.00 to 99.99, and "0.1" for 100.0 to 200.0 *2 Symbols in the "Data copy" column Y: Will be copied unconditionally. Y1: Will not be copied if the rated capacity differs from the source inverter. Y2: Will not be copied if the rated input voltage differs from the source inverter. N: Will not be copied.

Data Default setting copy*2

*3 Reserved for the maker. Do not set any data. <Changing, validating, and saving function code data when the motor is running> : Impossible, : Possible (Change data with keys and then save/validate it with key), : Possible (Change and validate data with keys and then save it with key)

Functions Settings

Func. Code

fuji frenic multi  
fuji frenic multi  

fuji frenic multi

Advertisement