Page 1

Technical Sheets Technical sheet products How to use it Certifications/Norms


Technical Sheets Next Tape

NM2BTS05

___________________________Pag 3

NM4BTS05

___________________________Pag 4

NM2BT15

___________________________Pag 5

NM3BT15

___________________________Pag 6

NM2BT25C105

___________________________Pag 7

NM2BT25

___________________________Pag 9

NM3BT25

___________________________Pag 10

TUV Certifications and Applied Norms

__________________Pag 12


NM2BTS05 TAPE DESCRIPTION

2

An adhesive electrical tape with 2 conductor tracks of 0,5 mm total width tape 25 mm wide.

POWER

Installation, change of position and control of LED lights or lights with working voltage < 50 Vac or < 75 Vdc. Installation, change of position ,control of switch/receiver to operate spot LED lights or lights with working voltage < 50 Vac or < 75 Vdc. Powering of Speaker with working voltage audio < 50 Vac o < 75Vdc. Conductor of audio signal from audio system/audio source to speakers. No impedance limits. Band 0…100kHz Conduction to plug, switch, socket or points with voltage< 50 Vac (transformer) or 75Vdc (feeder).

HOME AUTOMATION SYSTEM

Powering and Transmission of 2 cables home automation system signal to devices with voltage < 50 Vac or < 75Vdc..

LIGHTING

AUDIO

SECURITY NORMATIVE: PARTICULAR CHARATERISTICS

APPLYING CONDITIONS

HOW TO APPLY AND RULES

Powering and transmission of signals to and from fire sensors and security devices. Powering and transmission of signals for EVAC devices. see page n° 11 Warehousing and transport temperature:-10°C+50°C Maximum temperature of consecutive usage: +85°C Maximum temperature for usage in short period*: +105°C Maximum Humidity @ Tamb = +55°C: 93% Maximum altitude: 5.000m Insulation Voltage, Ui: 1.500V AC Voltage resistance to the impulse: 5.000V 2 Voltage density: 9A/mm * "short period" mean maximum 30 minutes continuously Minimum temperature for application: *+20°C First we recommend to study and measure the exact position where you want to install the product so mistakes can be avoided, be aware that this product cannot be applied more than once. To maximize adhesion the tape must be installed on an area that is dry and clean from powder and residuals. We recommend to use a primer substance (primer NEXT or something similar) to better guarantee it’s adhesion/resistance. *Minimum drying time for the adhesive is around 8 hours at a temperature of about +20°C. After application, you need to make a light friction movement over the surface of the tape using an instrument, for example a plastic/rubber roll. This not only helps the adhesion but it also removes eventual air bubbles. Note: If you choose to cover the tape with any type of filling you will need to apply a protective net prior


NM4BTS05 TAPE DESCRIPTION

LIGHTING

AUDIO

HOME AUTOMATION SYSTEM

POWER

SECURITY

2

An adhesive electrical tape with 4 conductor tracks of 0,5 mm total width tape 50 mm wide. Installation, change of position and control of LED lights or lights with working voltage < 50 Vac or < 75 Vdc. Installation, change of position ,control of switch/receiver to operate spot LED lights or lights with working voltage < 50 Vac or < 75 Vdc. Powering of Speaker with working voltage audio < 50 Vac o < 75Vdc. Conductor of audio signal from audio system/audio source to speakers. No impedance limits. Band 0…100kHz Powering and Transmission of 4 cables home automation system signal to devices with voltage < 50 Vac or < 75Vdc.. Conduction to plug, switch, socket or points with voltage< 50 Vac (transformer) or 75Vdc (feeder). Powering and transmission of signals to and from fire sensors and security devices. Powering and transmission of signals for EVAC devices.

NORMATIVE:

see page n° 11

PARTICULAR CHARATERISTICS

Warehousing and transport temperature:-10°C+50°C Maximum temperature of consecutive usage: +85°C Maximum temperature for usage in short period*: +105°C Maximum Humidity @ Tamb = +55°C: 93% Maximum altitude: 5.000m Insulation Voltage, Ui: 1.500V AC Voltage resistance to the impulse: 5.000V 2 Voltage density: 9A/mm * "short period" mean maximum 30 minutes continuously Minimum temperature for application: *+20°C First we recommend to study and measure the exact position where you want to install the product so mistakes can be avoided, be aware that this product cannot be applied more than once. To maximize adhesion the tape must be installed on an area that is dry and clean from powder and residuals. We recommend to use a primer substance (primer NEXT or something similar) to better guarantee it’s adhesion/resistance. *Minimum drying time for the adhesive is around 8 hours at a temperature of about +20°C. After application, you need to make a light friction movement over the surface of the tape using an instrument, for example a plastic/rubber roll. This not only helps the adhesion but it also removes eventual air bubbles. Note: If you choose to cover the tape with any type of filling you will need to apply a protective net prior

APPLYING CONDITIONS

HOW TO APPLY AND RULES


NM2BT15 TAPE DESCRIPTION

2

An adhesive electrical tape with 2 conductor tracks of 1,5 mm total width tape 75 mm wide.

LIGHTING

Installation, change of position and control of lights. Installation, change of position ,control of switch/receiver to operate lights

AUDIO

Powering of Speaker Conductor of audio signal from audio system/audio source to speakers. Conduction to plug, switch, socket or points.

POWER NORMATIVE: PARTICULAR CHARATERISTICS

APPLYING CONDITIONS

HOW TO APPLY AND RULES

see page n° 11 Warehousing and transport temperature:-10°C+50°C Maximum temperature of consecutive usage: +85°C Maximum temperature for usage in short period*: +105°C Maximum Humidity @ Tamb = +55°C: 93% Maximum altitude: 5.000m Insulation Voltage, Ui: 1.500V AC Voltage resistance to the impulse: 5.000V 2 Voltage density: 9A/mm * "short period" mean maximum 30 minutes continuously Minimum temperature for application: *+20°C First we recommend to study and measure the exact position where you want to install the product so mistakes can be avoided, be aware that this product cannot be applied more than once. To maximize adhesion the tape must be installed on an area that is dry and clean from powder and residuals. We recommend to use a primer substance (primer NEXT or something similar) to better guarantee it’s adhesion/resistance. *Minimum drying time for the adhesive is around 8 hours at a temperature of about +20°C. After application, you need to make a light friction movement over the surface of the tape using an instrument, for example a plastic/rubber roll. This not only helps the adhesion but it also removes eventual air bubbles. Note: If you choose to cover the tape with any type of filling you will need to apply a protective net prior For low tension application, after application we reccomend to cover with correct material, to guaratee mechanical protection for the product, as for Normative applied in the country where the product is installed


NM3BT15 TAPE DESCRIPTION

2

An adhesive electrical tape with 3 conductor tracks of 1,5 mm total width tape 75 mm wide.

LIGHTING

Installation, change of position and control of lights. Installation, change of position ,control of switch/receiver to operate lights

AUDIO

Powering of Speaker Conductor of audio signal from audio system/audio source to speakers. Conduction to plug, switch, socket or points.

POWER NORMATIVE: PARTICULAR CHARATERISTICS

APPLYING CONDITIONS

HOW TO APPLY AND RULES

see page n° 11 Warehousing and transport temperature:-10°C+50°C Maximum temperature of consecutive usage: +85°C Maximum temperature for usage in short period*: +105°C Maximum Humidity @ Tamb = +55°C: 93% Maximum altitude: 5.000m Insulation Voltage, Ui: 1.500V AC Voltage resistance to the impulse: 5.000V 2 Voltage density: 9A/mm * "short period" mean maximum 30 minutes continuously Minimum temperature for application: *+20°C First we recommend to study and measure the exact position where you want to install the product so mistakes can be avoided, be aware that this product cannot be applied more than once. To maximize adhesion the tape must be installed on an area that is dry and clean from powder and residuals. We recommend to use a primer substance (primer NEXT or something similar) to better guarantee it’s adhesion/resistance. *Minimum drying time for the adhesive is around 8 hours at a temperature of about +20°C. After application, you need to make a light friction movement over the surface of the tape using an instrument, for example a plastic/rubber roll. This not only helps the adhesion but it also removes eventual air bubbles. Note: If you choose to cover the tape with any type of filling you will need to apply a protective net prior For low tension application, after application we reccomend to cover with correct material, to guaratee mechanical protection for the product, as for Normative applied in the country where the product is installed


NM2BT25C105 Descrizione del cavo

LIGHTING AUDIO

2

An adhesive electrical tape with 2 conductor tracks of 2,5 mm + 1 of 0,5 2 mm total width tape 55 mm wide Installation, change of position and control of lights. Installation, change of position ,control of switch/receiver to operate lights Powering of Speaker Conductor of audio signal from audio system/audio source to speakers. Conduction to plug, switch, socket or points.

POWER LIGHTING

AUDIO

POWER HOME AUTOMATION SYSTEM SECURITY NORMATIVE: PARTICULAR CHARATERISTICS

APPLYING CONDITIONS

Follow next page

Installation, change of position and control of LED lights or lights with working voltage < 50 Vac or < 75 Vdc. Installation, change of position ,control of switch/receiver to operate spot LED lights or lights with working voltage < 50 Vac or < 75 Vdc. Powering of Speaker with working voltage audio < 50 Vac o < 75Vdc. Conductor of audio signal from audio system/audio source to speakers. No impedance limits. Band 0…100kHz Conduction to plug, switch, socket or points with voltage< 50 Vac (transformer) or 75Vdc (feeder). Powering and Transmission of 2 cables home automation system signal to devices with voltage < 50 Vac or < 75Vdc.. Powering and transmission of signals to and from fire sensors and security devices. Powering and transmission of signals for EVAC devices. see page n° 11 Warehousing and transport temperature:-10°C+50°C Maximum temperature of consecutive usage: +85°C Maximum temperature for usage in short period*: +105°C Maximum Humidity @ Tamb = +55°C: 93% Maximum altitude: 5.000m Insulation Voltage, Ui: 1.500V AC Voltage resistance to the impulse: 5.000V 2 Voltage density: 9A/mm * "short period" mean maximum 30 minutes continuously Minimum temperature for application: *+20°C First we recommend to study and measure the exact position where you want to install the product so mistakes can be avoided, be aware that this product cannot be applied more than once. To maximize adhesion the tape must be installed on an area that is dry and clean from powder and residuals. We recommend to use a primer substance (primer NEXT or something similar) to better guarantee it’s adhesion/resistance. *Minimum drying time for the adhesive is around 8 hours at a temperature of about +20°C.


HOW TO APPLY AND RULES

After application, you need to make a light friction movement over the surface of the tape using an instrument, for example a plastic/rubber roll. This not only helps the adhesion but it also removes eventual air bubbles. Note: If you choose to cover the tape with any type of filling you will need to apply a protective net prior For low tension application, after application we reccomend to cover with correct material, to guaratee mechanical protection for the product, as for Normative applied in the country where the product is installed


NM2BT25 TAPE DESCRIPTION

2

An adhesive electrical tape with 2 conductor tracks of 2,5 mm total width tape 50 mm wide.

LIGHTING

Installation, change of position and control of lights. Installation, change of position ,control of switch/receiver to operate lights

AUDIO

Powering of Speaker Conductor of audio signal from audio system/audio source to speakers. Conduction to plug, switch, socket or points.

POWER NORMATIVE: PARTICULAR CHARATERISTICS

APPLYING CONDITIONS

HOW TO APPLY AND RULES

see page n° 11 Warehousing and transport temperature:-10°C+50°C Maximum temperature of consecutive usage: +85°C Maximum temperature for usage in short period*: +105°C Maximum Humidity @ Tamb = +55°C: 93% Maximum altitude: 5.000m Insulation Voltage, Ui: 1.500V AC Voltage resistance to the impulse: 5.000V 2 Voltage density: 9A/mm * "short period" mean maximum 30 minutes continuously Minimum temperature for application: *+20°C First we recommend to study and measure the exact position where you want to install the product so mistakes can be avoided, be aware that this product cannot be applied more than once. To maximize adhesion the tape must be installed on an area that is dry and clean from powder and residuals. We recommend to use a primer substance (primer NEXT or something similar) to better guarantee it’s adhesion/resistance. *Minimum drying time for the adhesive is around 8 hours at a temperature of about +20°C. After application, you need to make a light friction movement over the surface of the tape using an instrument, for example a plastic/rubber roll. This not only helps the adhesion but it also removes eventual air bubbles. Note: If you choose to cover the tape with any type of filling you will need to apply a protective net prior For low tension application, after application we reccomend to cover with correct material, to guaratee mechanical protection for the product, as for Normative applied in the country where the product is installed


NM3BT25 TAPE DESCRIPTION

2

An adhesive electrical tape with 3 conductor tracks of 2,5 mm total width tape 75 mm wide.

LIGHTING

Installation, change of position and control of lights. Installation, change of position ,control of switch/receiver to operate lights

AUDIO

Powering of Speaker Conductor of audio signal from audio system/audio source to speakers. Conduction to plug, switch, socket or points.

POWER NORMATIVE: PARTICULAR CHARATERISTICS

APPLYING CONDITIONS

HOW TO APPLY AND RULES

see page n° 11 Warehousing and transport temperature:-10°C+50°C Maximum temperature of consecutive usage: +85°C Maximum temperature for usage in short period*: +105°C Maximum Humidity @ Tamb = +55°C: 93% Maximum altitude: 5.000m Insulation Voltage, Ui: 1.500V AC Voltage resistance to the impulse: 5.000V 2 Voltage density: 9A/mm * "short period" mean maximum 30 minutes continuously Minimum temperature for application: *+20°C First we recommend to study and measure the exact position where you want to install the product so mistakes can be avoided, be aware that this product cannot be applied more than once. To maximize adhesion the tape must be installed on an area that is dry and clean from powder and residuals. We recommend to use a primer substance (primer NEXT or something similar) to better guarantee it’s adhesion/resistance. *Minimum drying time for the adhesive is around 8 hours at a temperature of about +20°C. After application, you need to make a light friction movement over the surface of the tape using an instrument, for example a plastic/rubber roll. This not only helps the adhesion but it also removes eventual air bubbles. Note: If you choose to cover the tape with any type of filling you will need to apply a protective net prior For low tension application, after application we reccomend to cover with correct material, to guaratee mechanical protection for the product, as for Normative applied in the country where the product is installed


NORMATIVE

CEI EN 50395

CEI EN 50396 CEI EN 60811-1-1

CEI EN 60811-1-2

CEI EN 60811-1-3

CEI EN 60811-4: 2005

CEI EN 60811-4-1

CEI EN 60811-4-2

CEI EN 60332-1-1

CEI EN 60332-2

EN 50268 – 2 - (EN 61034-2)

CEI 20-37/7

EN 50200

Special Test Plane TÜV Intercert GmbH

YEAR

2006

2007

2001

2001

2001

2005

2005

2005

2006

2006

2000

2000

2000

2012

NEXT TAPE Flat CableTechnical Sheets  

How to use, Characteristics, Norms, for all the Next Tapes. the adhesive flat cable

Read more
Read more
Similar to
Popular now
Just for you