Page 1

Arms, Armor and Awesome

About Us

Cosplay

A cosplay blog.

Tutorials

← Queen o f Blades update: August 2

Queen o f Blades update: August 9 →

Arms , Armor and Awes ome

Resin and Pepakura : A simple guide to the safe use of fiberglass resin Po sted o n August 5, 20 11 by Ryitho s

There are lots of tutorials on “How to fiberglass” and ” How to create Pepakura” but there these seem to skip the steps between building the Pepakura pattern and laying the fiberglass.

Promote Your Page Too PDFmyURL.com


Our Triple A Cosplay Team! RampagingCoconut

Ryithos

Marine Helm from Halo: Combat Evolved (File from Halo costuming Wiki). This Tutorial will help walk you through the handling, set up and mixing of fiberglass resins along with a bit on how to coat your project to get full penetration of the resin in to the paper. !! Safety First!! 1. Ventilation: Always work in a well ventilated area, a garage will work but I strongly recomend a fan to help move the air around. Failure to do this will result in feeling faint, light headedness, and headaches. These are the first things that will occur when exposed to the fumes for to long. 2. Mask: This can be prevented through the use of a properly fitted respirator. Fit Test Guide An OV/P95 is ideal for this and should be used if at all possible. These are available from most home improvement warehouses for around $20. 3. Gloves: Can’t say enough about this, most people only get two hands and if you want them to stay in a useable condition you will want to protect them from the harsh chemicals in the resin. Nitrile Gloves and Latex Gloves work great and are cheap enough to use and discard. You may change your gloves 2-3 times every 20 min while working with fiberglass to keep your hands from becoming to sticky to handle your project.

lyeric

Search

Recent Posts Q ueen of Blades update: September 13 Q ueen of Blades update: September 7 Q ueen of Blades update: Augus t 28 Q ueen of Blades Update: Augus t 23 Q ueen of Blades update: Augus t 16

Subscribe! Enter your email addres s to s ubs cribe to this blog and receive notifications of new pos ts by email. Join 13 other followers

Sign me up!

Archives September 2011 Augus t 2011 July 2011 June 2011 PDFmyURL.com


Ok, now that you are safely outfitted with the proper personal protection equipment (PPE) we can start the project.

June 2011 May 2011 April 2011 March 2011 February 2011 January 2011 November 2010 O ctober 2010 September 2010 Augus t 2010

Categories Commis s ions Contes t Conventions Cos play

We start with a pepakura pattern printed out on cardstock. although a bit tougher to fold, this

Do's and Don'ts

thicker paper will help absorb more of the resin when we finish the project.

Female Witch Doctor Kerrigan Makeup Male Witch Doctor Q ueen of Blades update Review Sewing Shoulder Armor Tutorial Uncategoriz ed Weapon Wig Styling

Our Links! The O riginal Pocket Podcas t

Work in a controlled manner and make sure each piece is connected to the right tab. If you do

Raine’s Cos tumes

screw up, print off a new piece and try again. The amount of time spent getting this right will greatly improve the end project.

The Art of Jenny Harris Zerina Cos play Kamui Cos play Lyeric Cos play

!! Do not use tape of any sort to hold your project together!!

Arms , Armor and Awes ome Facebook Page PDFmyURL.com


All tapes will de-solve when the resin is applied and your item will fall apart. Hot glue works well but can be a bit thick at the joints. I have always used “gel style� superglue and it has produced great results.

Facebook Page Cos play Tutorial Cos play Tutorial (Facebook) Cos play Blog

These projects are as easy as fold on the dotted line, cut on the solid line, and match the numbers up and glue. A great project for the starting cosplayer. Several popular cosplays from Starwars Storm Troopers to Halo armor are avalible in Pepakura patterns.

PDFmyURL.com


Time to head out to our well ventalated area and do some work with the resins. A good measuring cup is important to ensure a good mix and proper measures. As you work more and more with the resins you begin to get a feel for how much you will need. In this case 4oz of resin will be required.

PDFmyURL.com


The resin used in this tutorial is a polyester resin that uses a catalyst to cause it harden. Although you technically cant add too much (there is a limit to how much can be mixed), you will want to do a few small test batches to find a good working time / cure for your area. Make sure to write down the ratio of resin to catalyst so you remember what’s best for your area. Humidity, elevation, and temperature all will effect the amount needed. A good rule of thumb is the more catalyst you add, the faster your resin will set up, and the hotter it will cure.

For my house in California at about 75ft of elevation and 65 degrees, I will be using a pretty simple formula to figure out the amount of catalyst needed. This is a good starting point and can be PDFmyURL.com


adjusted depending on your results. Amount of resin in ounces (OZ) / 2 = amount of catalyst in Cubic Centimeters (CC) 4OZ /2 = 2CC of catalyst. Once you mix the two parts you are at a point of no return, 45 second of mixing will help ensure that you have fully intigrated the two parts and that the resin will fully cure in aprox 15-20 min.

I have positioned the helmet on a silicone mat to prevent sticking to my work surface. When cured the resin peels off the mat and does no harm. A great investment for anyone working with resins and hotglue.

PDFmyURL.com


Libraly apply the resin over the project. You will begin to see it soak into the paper. It is key that the resin fully penetrates the cardstock. As it works into the material you will see the cardstock become slightly trasparent. it gets a “greasy napkin” look to it.

Once you have fully coated the inside and out of the object and you’re happy with the coverage, you will want to position the item where ever you will let it cure at and do one last brush over the surface to help remove any runs or puddles of resin that may be on your project.

PDFmyURL.com


Alright at this point you are done until the resin cures. It should set up and be able to be handled in about 30 min, full cure and durability won’t happen for almost 24 hours. Try to leave the item alone as long as possible to ensure the best results. I hope this helps you in your quest for awesome looking and pretty easy to create costume pieces. Don’t be scared of fiberglass resin and don’t assume its just for the “serious” cosplayers. Like all tools it needs to be understood and applied in the right situation but It is still easy enough for any one to use. I’ll make making a followup post on how to finish your helmet (paint, etc) soon. Good luck and good crafting, PDFmyURL.com


Good luck and good crafting, Mario “Ryithos” FEAT UR ED O N EC O PR ESSED

Barefoot math professor runs for environment Eco World Content From Acros s The Internet.

Be the first to like this po st. This entry was po sted in Co splay, Tuto rial and tagged co splay, fiberglass, halo armo r, pepakura, resin. Bo o kmark the permalink. ← Queen o f Blades update: August 2

Queen o f Blades update: August 9 →

One Response to Resin and Pepakura : A simple guide to the safe use of fiberglass resin catfetus says: August 5, 20 11 at 8 :26 am

Looking forward to the finishing tutorial (as I am currently having trouble with that)! Reply

Leave a Reply

PDFmyURL.com


Enter your comment here...

Guest

Lo g In

Lo g In

Email ( re q uire d )

Lo g In

(Not published)

Name ( re q uire d ) Website

No tify me o f fo llo w-up co mments via email.

Post Comment

No tify me o f new po sts via email.

Arms, Armor and Awesome

Theme: Twenty Ten

Blog at WordPress.com .

PDFmyURL.com

Resin & Pepakura - Helmet  

About Us Cosplay Tutorials PDFmyURL.com Arms, Armor and Awesome Posted on August 5, 2011 by Ryithos Queen of Blades update: August 9 → Promo...

Read more
Read more
Similar to
Popular now
Just for you