Issuu on Google+

INDEX

COMPANY INTRODUCTION CENTRIFUGAL PUMP DEEP WELL TURBINE PUMP 4” SUBMERSIBLE PUMP 6” SUBMERSIBLE PUMP 8” SUBMERSIBLE PUMP 10” SUBMERSIBLE PUMP 12” SUBMERSIBLE PUMP 4” , 6” , 8” , 10” SUBMERSIBLE MOTOR 3 PHASE MOTORS FOOT MOUNTED ASE FRAME AND COUPLING GASOLINE /PETROL GENERATORS OPEN TYPE DIESEL GENERATORS SOUND PROOF/WEATHER PROOF DG SET TRAILER MOUNTED DG SET CANOPIES FOR DG SET ATS/MCU ACCESSORIES TUBE WELL DRILLING OTHERS


Centrifugal Pump Fields of Application Water supply

Cooling water

Fire-fighting systems

Swimming pool water

Sprinkling

Sea water

Irrigation

Fire-fighting water

Drainage

Brackish water

Heating

Condensate

Air-conditioning systems

Brine

Drinking water

Oils

Service water

Cleaning agents

Hot water

Operating Data Q

up to

t

660 m3/h, 183 l/s

H

up to

102 m

-30째C to +140째C

p2

up to

6 bar

Design Horizontal volute casing pump, single-stage, with power ratings and main dimensions to EN 733, with bearing bracket, in back pull-out design. Shaft with replaceable shaft sleeve/shaft protecting sleeve in the shaft seal area. Volute casing and impeller with replaceable wear rings. Volute casing with integrally cast pump feet.

Coupling Flexible coupling with/without spacer sleeve

Contact Guard coupling guard as per EN 294.

Base plate Sectional steel / folded steel plate for the complete unit (pump and motor) in torsion-resistant design

Bearings Deep-groove ball bearings, grease-lubricated

Shaft Seal Mechanical seal to DIN 24 960 or gland packing.

Due to continuous efforts in improvements, information furnished above is subject to change without notice


DEEP WELL TURBINE PUMP

Application: These pumps are suitable for water supply schemes, Irrigation schemes, lowering of ground water level and dewatering of mines and construction sites. Deep well turbine pumps particularly suitable for barrow bore holes. Minimum bore sizes hole sizes range form 200mm to 675mm.

Operating Data:Capacity Q

up to

2600 m3/hr

Head H

up to

160 m

Speed n

up to

3500 RPM

Temperature t

up to

105 C

Suspended Depth

up to

120 m

Design:Main pump components are the pump bowl Assembly , column and shaft assembly, and the discharge head assembly. Single or multistage radically split, interchangeable intermediate bowls. Interchangeable lengths of the column assembly and variable setting depth.

Wet Pit Installation In normal operation, the pump body is submerged and suspended in the fluid pumped, supported by the discharge head.

Dry Pit Installation:The pump can also be installed in dry pits. For this purpose a foot cum elbow are fitted in the suction pipe, thus enabling the pump to be connected to the source. An adapter piece is also provided to cater for the possibility of expansion in the axial direction, when the temperature fluctuates.

Drives:DWT pumps are driven either by the vertical hollow/solid shaft electric motor or a diesel (IC) engine. If an IC engine is used as a drive the drive transmission can be affected via bevel gears. A torsion ally flexible card an shaft is fitted as a coupling in this case.

Due to continuous efforts in improvements, information furnished above is subject to change without notice


4” SUBMERSIBLE PUMP SINGLE PHASE & THREE PHASE Multistage submersible borehole pumps made of stainless steel and plastics for well diameters as from 100 mm (4 inch) available with single-phase a.c. and three-phase current motors with short cable. Applications: domestic water supply irrigation and spray irrigation, lowering ground water levels fire protection systems, cooling circuits, as well as fountain, pressure boosting and air-conditioning systems.

SINGLE PHASE SUBMERSIBLE PUMP DISCHARGE IN m³/hr. Head in meter

1C/7 1C/10

0.37/0.5 0.37/0.5

34 49

29 42

27 38

21 30

14 20

1C/13

0.55/0.75

64

55

50

39

26

1C/15

0.55/0.75

74

64

58

45

31

1C/18

0.55/0.75

89

76

69

54

37

1C/21 1C/25

0.75/1.0 0.75/1.0

104 124

90 107

81 97

64 76

43 52

SINGLE PHASE SUBMERSIBLE PUMP DISCHARGE IN m³/hr. HEAD IN METER Type 2C/7

KW/hp 0.37/0.5

1.1

1.6

2

2.5

2.8

34

30

27

20

13

0.55/0.75 2C/10 2C/11

0.55/0.75 0.75/1.0

49 55

44 49

38 42

29 32

19 21

2C/13 2C/15

0.75/1.0 0.75/1.0

65 74

57 66

50 58

38 43

25 29

2C/18 2C/21 2C/23 2C/25 2C/27 2C/30 2C/33 2C/38 2C/45

1.0/1.5 1.0/1.5 1.1/1.5 1.1/1.5 1.5/2 1.5/2 2.2/3.0 2.2/3.0 2.2/3.0

89 104 113 122 132 147 159 186 217

79 92 101 109 118 131 142 165 193

69 81 88 95 103 114 124 145 169

52 60 66 71 77 86 93 109 127

35 40 44 48 51 57 62 72 85

Due to continuous efforts in improvements, information furnished above is subject to change without notice


4” SINGLE & THREE PHASE PUMP SINGLE PHASE PUMPS SINGLE PHASE SUBMERSIBLE PUMP -DISCHARGE HEAD IN m³/hr, HEAD IN METER

Type 4C/5

2

KW/HP 0.37/0.5

3

4

5

6

29

27

24

20

14

0.55/0.75 4C/6

0.55/0.75 0.72/1.0

34

32

29

24

17

4C/8 4C/10

0.75/1.0 1.1/1.5

46 52

43 48

38 43

32 36

23 26

4C/12

1.1/1.5

69

64

57

48

34

4C/15 4C/17

1.5/2.0 2.2/3.0

86 97

80 91

71 81

60 68

43 49

4C/19 4C/23

2.2/3.0 2.2/3.0

109 130

101 122

90 109

76 91

54 65

SINGLE PHASE SUBMERSIBLE PUMP-DISCHARGE HEAD IN m³/hr, HEAD IN 4 5 8 Type KW/h METER 6 7 p

7C/5

0.75/1.0

29

27

25

23

20

7C/7

1.1/1.5

40

38

35

32

28

7C/10

1.5/2.0

57

53

50

46

40

7C/12

2.2/3.0

68

63

59

54

47

7C/13

2.2/3.0

73

68

63

59

51

SINGLE PHASE PUMP - DISCHARGE HEAD IN m³/hr , HEAD IN METER Pump Type

KW/H P

9

12

16

20

22

18C/4

1.5/2.0 1.1/1.5

19

17

14

11

10

18C/5

1.5/2.0

24

21

18

14

12

18C/6

2.2/3.0

28

25

21

17

14

18C/7

2.2/3.0

33

30

25

20

16


4” SINGLE & THREE PHASE SUBMERSIBLE PUMP THREE PHASE PUMP 3 PHASE SUBMERSIBLE PUMP- HEAD IN METERS, DISCHARGE IN m₃/hr Pump Type

KW/HP

0.5

0.8

0.9

1.1

1.3

1C/7

0.75/1.0

35

30

27

21

15

1C/10

0.75/1.0

50

43

39

31

21

1C/12

0.75/1.0

65

56

51

40

27

75

65

58

46

30

1C/15

0.75/1.0

1C/18 1C/21

0.75/1.0 0.75/1.0

90 105

77 90

70 82

55 64

37 44

1C/21 1C/25

0.75/1.0 0.75/1.0

105 125

90 108

82 97

64 76

44 52

1C/30 1C/35

0.75/1.0 1.1/1.5

150 171

129 147

117 133

92 105

62 71

1C/40 1C/50

1.1/1.5 1.5/2.0

196 245

168 211

152 191

120 150

82 102

3 PHASE SUBMERSIBLE PUMP Discharge in m³/hr, HEAD IN METERS TYPE KW/HP

0.5

1.2

2.0

2.5

3.0

2C/11 2C/13 2C/15 2C/18 2C/21

0.75/1.0 0.75/1.0 0.75/1.0 1.1/1.5 1.1/1.5

60 71 82 96 112

51 61 70 82 96

43 51 58 69 80

32 38 44 51 60

21 25 29

2C/23 2C/25 2C/27 2C/30 2C/33 2C/38 2C/45

1.1/1.5 1.1/1.5 1.5/2.0 1.5/2.0 2.2/3.0 2.2/3.0 2.2/3.0

123 133 144 160 175 202 239

105 114 124 137 150 173 205

88 95 103 114 125 144 171

66 71 77 86 94 108 128

44 48 51 57 63 72 85

2C/50

3.0/4.0

259

222

185

139

93

34 40

3 PHASE SUBMERSIBLE PUMP - DISCHARGE IN m³/hr, HEAD IN METERS

KW/hp

0.5

1.2

2.0

2.5

3.0

4C/6

0.75/1.0

34

32

28

25

18

4C/8

0.75/1.0

45

43

38

33

23

4C/10 4C/12

1.1/1.5 1.1/1.5

56 67

53 64

47 56

40 49

29 35

4C/15

1.5/2.0

84

79

70

61

43

4C/17

2.2/3.0

95

90

79

69

49

4C/19

2.2/3.0

107

100

88

77

55

4C/23 4C/25

2.2/3.0 3.0/4.0

129 139

121 131

107 115

93 100

66 71

4C/30

3.7/5.0

166

156

137

119

85

4C/35

3.7/5.0

194

182

160

139

100

4C/40

3.7/5.0

221

209

183

159

114

Type


4” SINGLE & 3 PHASE SUBMERSIBLE PUMP

THREE PHASE PUMP 3 PHASE SUBMERSIBLE PUMP- DISCHRAGE IN m³/hr, HEAD IN METERS

Type 7C/5

KW/HP

4

0.75/1.0 29

5

6

7

8

27

25

23

20

7C/7

1.1/1.5

40

37

35

32

28

7C/10 7C/12

1.5/2.0 2.2/3.0

57 68

53 64

50 59

46 55

40 48

7C/15

2.2/3.0

85

80

74

68

60

7C/19

3.0/4.0

106

99

92

84

74

7C/22 7C/25

3.7/5.0 3.7/5.0

122 138

114 129

106 120

97 111

85 97

7C/31

4.5/6.0

176

164

152

141

123

3 PHASE SUBMERSIBLE PUMP - DISCHRAGE IN m³/hr, HEAD IN METERS

Type

KW/hp

6

8

1 0

12

14

12C/10 12C/13

2.2/3.0 3.0/4.0

57 74

51 67

43 55

33 43

23 30

12C/17 12C/21

3.7/5.0 4.5/6.0

94 116

85 105

71 87

55 68

38 47

3 PHASE SUBMERSIBLE PUMP - DISCHRAGE IN m³/hr, HEAD IN METERS

Type

KW/hp

9

12

15

18

22

18C/6 18C/7

1.5/2.0 2.2/3.0

29 33

27 31

22 25

17 20

14 17

18C/9

3.0/4.0

42

39

32

25

21

18C/10

3.0/4.0

46

43

35

28

23

18C/11 18C/12

3.7/5.0 3.7/5.0

51 55

47 52

39 42

30 33

25 28

18C/13

4.5/6.0

61

57

47

37

31

18C/14

4.6/6.0

66

62

51

40

33


6” SUBMERSIBLE PUMP Application:Domestic and general water supply duties. Irrigation and sprinkling systems Ground water pumping Cooling water circulation Pressure boosting plants Air Conditioning systems Fountain etc. Pump Construction / Design:Single or multistage, single entry centrifugal pumps of ring section type with radial or mixed flow impellers. Radial impellers are with renewable/integral diffusers and mixed flow impellers with stage bowl. The plain bearings are water lubricated. Suction strainer fitted on suction casing prevents ingress of coarse impurities. Higher stage pumps are fitted with intermediate bearing. The axial thrust is balanced by thrust bearing in the motor.

Operating data ( 50 Hz ) Capacity Head Max. Power Required Temp of liquid pumped Nominal Speed

Q H p t n

up to 70 m³/hr. up to 300m. up to 18.5 kw 30°C 2900 rpm

Bearing & Lubrication:Radial-plain bearings are lubricated by the pumped water. Depending on no. of stages: additionally one intermediate bearing is used in the pump.

The axial thrust is carried by the thrust bearing in motor. Direction of Rotation & operational speed:Clockwise when viewed from the drive shaft end. The pump performance curves are drawn from a standard sped of 2900 rpm. While referring to these curves the required duty point should be converted to the actual speed of the motor selected. Model: UQ 2100-4 UQ 2100-5 UQ 2100-6 UQ 2100-7 UQ 2100-8 UQ 2100-10 UQ 2100-12 UQ 2100-14 UQ 2100-17 UQ 2100-18 UQ2100-20

Head up to Head Up to Head up to Head Up to Head Up to Head Up to Head Up to Head Up to Head Up to Head Up to Head Up to

150 feet 190 feet 230 feet 275 feet 310 Feet 340 feet 500 feet 610 Feet 660 feet 700 feet 730 feet

Motor: 5 Hp Motor: 5 HP Motor: 6 HP Motor: 7.5 HP Motor: 10 HP Motor: 10 HP Motor: 12.5 HP Motor: 15HP Motor:17.5 HP Motor:17.5 HP Motor: 20 HP

UQ 2100-24

Head Up to

900 feet

Motor: 25 HP


6” SUBMERSIBLE PUMP Domestic and general water supply duties. Irrigation and sprinkling systems Ground water pumping Cooling water circulation Pressure boosting plants Air Conditioning systems Fountain etc. Pump Construction / Design:Single or multistage, single entry centrifugal pumps of ring section type with radial or mixed flow impellers. Radial impellers are with renewable/integral diffusers and mixed flow impellers with stage bowl. The plain bearings are water lubricated. Suction strainer fitted on suction casing prevents ingress of coarse impurities. Higher stage pumps are fitted with intermediate bearing. The axial thrust is balanced by thrust bearing in the motor.

Operating data ( 50 Hz ) Capacity Head Max. Power Required Temp of liquid pumped Nominal Speed

Q H p t n

up to 70 m³/hr. up to 300m. up to 18.5 kw 30°C 2900 rpm

Bearing & Lubrication:Radial-plain bearings are lubricated by the pumped water. Depending on no. of stages: additionally one intermediate bearing is used in the pump.

The axial thrust is carried by the thrust bearing in motor. Direction of Rotation & operational speed:Clockwise when viewed from the drive shaft end. The pump performance curves are drawn from a standard sped of 2900 rpm. While referring to these curves the required duty point should be converted to the actual speed of the motor selected.

Model: BP 2400-4 BP 2400-5 BP 2400-6 BP 2400-8 BP 2400-10 BP 2400-12 BP 2400-14 BP 2400-15 BP 2400-18

Head Up to Head Up to Head Up to Head Up to Head Up to Head Up to Head Up to Head Up to Head Up to

160 feet 200 feet 240 feet 325 feet 410 feet 490 feet 575 feet 615 feet 740 feet

Motor: Motor: Motor: Motor: Motor: Motor: Motor: Motor: Motor:

5 HP 6 HP 7.5 HP 10 HP 12.5 HP 15 HP 17.5 HP 20 HP 25 HP


6” SUBMERSIBLE PUMP Application:Domestic and general water supply duties. Irrigation and sprinkling systems Ground water pumping Cooling water circulation Pressure boosting plants Air Conditioning systems Fountain etc. Pump Construction / Design:Single or multistage, single entry centrifugal pumps of ring section type with radial or mixed flow impellers. Radial impellers are with renewable/integral diffusers and mixed flow impellers with stage bowl. The plain bearings are water lubricated. Suction strainer fitted on suction casing prevents ingress of coarse impurities. Higher stage pumps are fitted with intermediate bearing. The axial thrust is balanced by thrust bearing in the motor.

Operating data ( 50 Hz ) Capacity Head Max. Power Required Temp of liquid pumped Nominal Speed

Q H p t n

up to 70 m³/hr. up to 300m. up to 18.5 kw 30°C 2900 rpm

Bearing & Lubrication:Radial-plain bearings are lubricated by the pumped water. Depending on no. of stages: additionally one intermediate bearing is used in the pump.

The axial thrust is carried by the thrust bearing in motor. Direction of Rotation & operational speed:Clockwise when viewed from the drive shaft end. The pump performance curves are drawn from a standard sped of 2900 rpm. While referring to these curves the required duty point should be converted to the actual speed of the motor selected. Model: BP 3000-3 BP 3000-4 BP 3000-5 BP 3000-6 BP 3000-7 BP 3000-8 BP 3000-9 BP 3000-10 BP 3000-12

Head Up to Head Up to Head Up to Head Up to Head Up to Head Up to Head Up to Head Up to Head Up to

105 feet 140 feet 175 feet 210 feet 245 feet 280 feet 315 feet 350 feet 420 feet

Motor: Motor: Motor: Motor: Motor: Motor: Motor: Motor: Motor:

6 HP 7.5 HP 10 HP 12.5 HP 15 HP 17.5 / 20 HP 20 HP 25 HP 25 HP


6” SUBMERSIBLE Pump Application:Domestic and general water supply duties. Irrigation and sprinkling systems Ground water pumping Cooling water circulation Pressure boosting plants Air Conditioning systems Fountain etc. Pump Construction / Design:Single or multistage, single entry centrifugal pumps of ring section type with radial or mixed flow impellers. Radial impellers are with renewable/integral diffusers and mixed flow impellers with stage bowl. The plain bearings are water lubricated. Suction strainer fitted on suction casing prevents ingress of coarse impurities. Higher stage pumps are fitted with intermediate bearing. The axial thrust is balanced by thrust bearing in the motor.

Operating data ( 50 Hz ) Capacity Head Max. Power Required Temp of liquid pumped Nominal Speed

Q H p t n

up to 70 m³/hr. up to 300m. up to 18.5 kw 30°C 2900 rpm

Bearing & Lubrication:Radial-plain bearings are lubricated by the pumped water. Depending on no. of stages: additionally one intermediate bearing is used in the pump.

The axial thrust is carried by the thrust bearing in motor. Direction of Rotation & operational speed:Clockwise when viewed from the drive shaft end. The pump performance curves are drawn from a standard sped of 2900 rpm. While referring to these curves the required duty point should be converted to the actual speed of the motor selected.

Model: BP 3200-1D BP 3200-2B BP 3200-3D BP 3200-3A BP 3200-3C BP 3200-4B BP 3200-4C BP 3200-5C BP 3200-6C

Head Up to Head Up to Head Up to Head Up to Head Up to Head Up to Head Up to Head Up to Head Up to

72 feet 90 feet 110 feet 130 feet 145 feet 180 feet 196 feet 250 feet 290 feet

Motor: Motor: Motor: Motor: Motor: Motor: Motor: Motor: Motor:

7.5 HP 7.5 HP 10 HP 10 HP 12.5 HP 15 HP 17.5 HP 20 HP 25 HP


4� SUBMERSIBLE MOTORS This 4" submersible motors has been designed and produced according to the market requirement. In design and material selection all efforts have been made to offer a product to our customers which stand for reliability, excellent quality, long and trouble free life.

Technical specification Motor casing: AISI 304 stainless steel. Shaft: AISI 304 stainless steel. Bottom: AISI 304 stainless steel. Shaft coupling: according to Nema Standard. Bearings: axial and radial thrust ball bearings. Seal: graphite/ceramic mechanical seal. Rubber diaphragm: over size rubber diaphragm allows water volume regulation inside the motor, according to external pressure and operating temperature. Upper bracket: high resistance cast iron nickel plated . Filling fluid: special fluid, for a better lubricant effect, increase life of moving parts. Connection: removable cable connector.

Degree of protection: IP 58 Insulation class: F Voltage tolerance: +6% / -10% Mounting position: horizontal up to 2,2 kW Minimum flow rate speed: 0,8 m/s Maximum deep head: 150 m Water temperature: 35°C maximum Starting per hour: 30


6� SUBMERSIBLE MOTORS This 6" submersible motors has been designed and produced according to the market requirement. In design and material selection all efforts have been made to offer a product to our customers which stand for reliability, excellent quality, long and trouble free life. 6" submersible motors are asynchronous three phase, with squirrel cage and wet type rewind able stator. Technical specification Winding: made of pure electrolytic copper wire sheeted with a non-hygroscopic PVC, very strong for high temperature. Stator: with low-loss magnetic sheet, fixed into a casing stainless made. Rotor: only with copper bars. All rotors are dynamically balanced for smooth and vibration free operation. Shaft: AISI 420 stainless steel made, is oversized designed to assure stiffness. Shaft coupling: according to Nema Standard. Shaft bearing: upper and lower double bronze bearings. Thrust bearing: thrust sliding block bearing, self aligning Mitchell type, suitable for 15500 N axial thrust. Seal: silicon carbide mechanical seal for normal and sandy wells. Rubber diaphragm: together with upper inside and outside filters, allows water volume regulation inside the motor, according to external pressure and operating temperature. Brackets: high resistance nickel plated cast iron for upper and lower brackets. Filling fluid: special water, developed for motor's corrosion inside parts prevent and excellent cooling quality. Degree of protection: Voltage tolerance: 10% Mounting position: horizontal Minimum flow rate speed: Maximum deep head: Water temperature: maximum Starting per hour:

IP 68 +6% / vertical / 0,3 m/s 150 m 30°C 20


8” , 10 “ SUBMERSIBLE MOTOR

These 8", 10” submersible motors has been designed and produced according to the market requirement. In design and material selection all efforts have been made to offer a product to our customers which stand for reliability, excellent quality, long and trouble free operation. 8" submersible motors are asynchronous three phase, with squirrel cage and wet type rewind able stator.

Technical specification Winding: made of pure electrolytic copper wire sheeted with a non-hygroscopic PVC, very strong for high temperature.

Stator: with low-loss magnetic sheet, fixed into a casing stainless made. Rotor: only with copper bars. All rotors are dynamically balanced for smooth and vibration free operation.

Shaft: SS 420, oversized designed to assure stiffness. Shaft coupling: 8" NEMA Standard. Shaft bearing: upper and lower double bronze bearings. Thrust bearing: thrust sliding block bearing, self aligning Mitchell type, suitable for 45000 N axial thrust. Seal: silicon carbide for normal and sandy wells. Rubber diaphragm: together with upper inside and outside filters, allows water volume regulation inside the motor, according to external pressure and operating temperature. Brackets: high resistance nickel plated cast iron for upper and lower brackets. Filling fluid: special water. Degree of protection: Voltage tolerance: Mounting position: Minimum flow rate speed: Maximum deep head: Water temperature: Starting per hour:

IP 68 +6% / -10% vertical ~ 0,2 m/s (30~52kw) 0,5 m/s (55 93kw) 150 m 30°C maximum 10


3 PHASE STANDARD MTORS

General description Increasing energy costs mean that energy consumption is of increasing significance in drive technology. It is essential to fully exploit potential for minimizing these costs in order to remain competitive now and in the future. Lower energy consumption also benefits the environment. It is against this background that we are developing a new generation of lowvoltage motors, enabling you to do more with your motors. Innovative copper rotors create the very best basis for highly efficient motors. The new motors for IE2 (high efficiency) thereby offer large energy savings and are better for the environment. Also, the modular design concept provides full flexibility: each motor is based on a standardized concept for all international markets.

Technical data overview ( Foot Mounted ) Totally Enclosed Fan cooled squirrel cage induction motors as per DIN VDE 0530/IEC 34-1 3 Phase 400 VAC , 50 Hz Suitable for VFD Operation Ambient Temperature 40 °C , Altitude 1000 m above sea level, Construction IM B3 ( Foot Mounted) , Degree of Protection IP 55 , Insulation Class ‘F’ Power Range : 1 KW to 100 Kw ,

Pole 2, 4, 6

Technical data overview (Vertical hollow shaft motors ) Totally enclosed fan cooled squirrel cage vertical hollow shaft induction motors as per DIN VDE 0530 / IEC 34—1 3 Phase 400 VAC , 50 Hz, Ambient Temperature 40 °C , Altitude 1000 m above sea level, Construction IMV1 ( flange mounted ) with NEMA Flanges Degree of protection IP 44 , Insulation Class “ F “ , Motors are protected with PTC Thermistators which protect the windings against excessive heating under changing load conditions. Power Range: Pole

7.5 KW 2,4

to

75 KW


GASOLINE/PETROL GENERATORS

Portable Standby Generators Portable standby generator units are the dependable workhorses of the field ‌ whenever you simply need raw power. They are easy to use, safe and reliable. Some of the standard features and benefits include:

Features Automatic "Low-Oil-Shutdown" features to prevent damage Circuit breaker protection to protect the unit itself as well as your devices Full perimeter safety frame to prevent harm from hot surfaces and moving parts Optional wheel kits to enhance portability This rugged gasoline gen set delivers reliable power anywhere for emergency or residential standby power, maintenance crews and light commercial applications.

Models:Rated Output 1.3 kVA Consumption 0.97 litre / hour Tank Capacity 3.7 litres Engine GX160 Noise Level 66 dB Dry Weight 33 kg

Rated Output 2 kVA Consumption 1.15 litre / hour Tank Capacity 15 litres Engine

GX160

Noise Level

65 dB

Dry Weight

45 kg

Rated Output 4 kVA Consumption 2.5 litre / hour Tank Capacity 25 litres Engine GX340 Noise Level 70 dB Dry Weight 82 kg

Rated Output 5 kVA Consumption 2.71 litre / hour Tank Capacity 25 litres Engine GX390 Noise Level 72 dB Dry Weight 89 kg


Open Type Diesel Generators Cummins Diesel Generator Set Introduction:Cummins Inc., a global power leader, is a corporation of complementary business units that design, manufacture, distribute and service engines and related technologies since 1919, headquartered in Columbus, Indiana(USA),Cummins serves customers in approximately 190 countries and territories through a network of more than 500 Company-owned and independent distributor locations and approximately 5,200 dealer locations.

Genset model

Engine model

Prime power

Standby Power

AC28 AC28 AC41-Ⅰ AC41-Ⅱ AC55 AC62 AC69 AC110 AC110 AC138 AC149 AC165 AC206 AC220 AC275 AC343 AC275 AC275 AC303 AC343 AC375 AC413 AC450 AC500 AC625 AC660 AC688 AC715 AC825 AC1000 AC1100 AC1238 AC1375

4B3.9-G1 4B3.9-G2 4BT3.9-G1 4BT3.9-G2 4BTA3.9-G2 4BTA3.9-G2 4BTA3.9-G2 6BT5.9-G1 6BT5.9-G2 6BTA5.9-G2 6BTAA5.9-G2 6CTA8.3-G2 6CTA8.3-G2 6CTAA8.3-G2 6LTAA8.9-G2 QSM11-G2 NT855-GA MTA11-G2A NTA855-G1A MTAA11-G3 NTA855-G2A NTAA855-G7A NTAA855-G7A KTA19-G3 KTAA19-G5 KTAA19-G6A KTAA19-G6A QSK19-G3 KTA38-G2 KTA38-G2A KTA38-G5 KTA38-G9 KTAA38-G9A

20/25 20/25 30/38 30/38 40/50 45/56 50/63 80/100 80/100 100/125 108/135 120/150 150/188 160/200 200/250 250/313 200/250 200/250 220/275 250/313 280/344 300/375 320/400 360/450 450/565 480/600 500/625 520/650 600/750 720/900 800/1000 900/1125 1000/1250

22/27.5 22/27.5 33/41 33/41 44/55 50/62 55/69 88/110 88/110 110/138 119/149 132/165 165/206 176/220 220/275 275/343 220/275 220/275 242/303 275/343 300/375 330/413 360/450 400/500 500/625 528/660 500/688 572/715 660/825 800/1000 880/1100 990/1238 1100/1375

For complete details/specifications and big power please contact us


Open Type Diesel Generators Perkins/Lovol Diesel Generator set

Genset model

Engine model

Prime power KW/KVA

Standby Power KW/KVA

Fuel Consumption ≤g/kw.h

dimension mm

Weight kg

AP10

403D-11

7/9

8/10

248

1280×500×860

330

AP14

403D-15

10/13

11/14

248

1280×500×950

390

AP22

404D-22

16/20

18/22

237

1420×500×1000

470

AP33

1103A-33G

24/30

26/33

235

1520×650×1200

750

AP50

1103A-33TG1

36/45

40/50

235

1520×650×1200

770

AP66

1103A-33TG2

48/60

53/66

235

1520×650×1200

770

AP72

1104A-44TG1

52/65

57/72

208

1800×650×1200

840

AP88

1104A-44TG2

64/80

70/88

208

1800×650×1200

850

AP110

1104C-44TAG2

80/100

88/110

205

1850×700×1200

1120

AP150

1006TAG

108/135

120/150

208

2250×800×1280

1200

AP165

1006TAG2

120/150

132/165

208

2300×900×1560

1400

AP220

1306C-E87TAG3

160/200

176/220

207

2530×900×1560

1640

AP248

1306C-E87TAG4

180/225

198/248

201

2530×900×1560

1725

AP259

1306C-E87TAG5

188/235

207/259

203

2530×900×1560

1800

AP880

4006-23TAG3A

640/800

704/880

210

3780×1710×2200

4960

AP990

4008TAG1A

720/900

792/990

206

4800×2030×2170

7100

AP1100

4008TAG2A

800/1000

880/1100

214

4800×2030×2170

7100

AP1375

4012-46TWG2A

1000/1250

1100/1375

212

5100×2050×2400

8600

AP1650

4012-46TAG2A

1200/1500

1320/1650

200

5310×2050×2400

9500

AP1925

4016TAG

1400/1750

1540/1925

205

5900×2300×3000

14500

AP2030

4016TAG1A

1476/1845

1624/2030

205

5900×2300×3000

14500

AP2263

4016TAG2A

1646/2058

1811/2263

209

6000×2300×3000

14800


Open Type Diesel Generators Doosan Daewoo Diesel Generators

Genset model

Engine model

Prime power KW/KVA

Standby

Fuel

Power KW/KVA

Consumption ≤L/h

dimension mm

Weight kg

AD66

DB58

48/60

53/66

18.1

2100×800×1400

1100

AD96

D1146

70/88

77/96

20.8

2350×900×1300

1500

AD138

D1146T

100/125

110/138

27

2400×900×1300

1600

AD186

P086TI-1

135/169

149/186

48.4

2600×950×1450

1750

AD220

P086TI

160/200

176/220

48.4

2600×950×1450

1825

AD303

P126TI

220/275

242/303

66.2

3000×1000×1650 2200

AD344

P126TI-II

250/313

275/344

77.6

3000×1000×1650 2300

AD413

P158LE-1

300/375

330/413

102.9

3100×1390×1700 2500

AD440

P158LE

320/400

352/440

102.9

3100×1400×1800 2800

AD495

P158LE-S

360/450

396/495

109.7

3300×1400×1800 3050


Sound Proof/ Weather Proof /Trailer Mounted DG Sets

Cummins Diesel Generator set

Introduction:Cummins Inc., a global power leader, is a corporation of complementary business units that design, manufacture, distribute and service engines and related technologies since 1919, headquartered in Columbus, Indiana(USA),Cummins serves customers in approximately 190 countries and territories through a network of more than 500 Company-owned and independent distributor locations and approximately 5,200 dealer locations.

Genset model

Engine model

Prime power

Standby Power

AC28 AC28 AC41-Ⅰ AC41-Ⅱ AC55 AC62 AC69 AC110 AC110 AC138 AC149 AC165 AC206 AC220 AC275 AC343 AC275 AC275 AC303 AC343 AC375 AC413 AC450 AC500 AC625 AC660 AC688 AC715 AC825 AC1000 AC1100 AC1238 AC1375

4B3.9-G1 4B3.9-G2 4BT3.9-G1 4BT3.9-G2 4BTA3.9-G2 4BTA3.9-G2 4BTA3.9-G2 6BT5.9-G1 6BT5.9-G2 6BTA5.9-G2 6BTAA5.9-G2 6CTA8.3-G2 6CTA8.3-G2 6CTAA8.3-G2 6LTAA8.9-G2 QSM11-G2 NT855-GA MTA11-G2A NTA855-G1A MTAA11-G3 NTA855-G2A NTAA855-G7A NTAA855-G7A KTA19-G3 KTAA19-G5 KTAA19-G6A KTAA19-G6A QSK19-G3 KTA38-G2 KTA38-G2A KTA38-G5 KTA38-G9 KTAA38-G9A

20/25 20/25 30/38 30/38 40/50 45/56 50/63 80/100 80/100 100/125 108/135 120/150 150/188 160/200 200/250 250/313 200/250 200/250 220/275 250/313 280/344 300/375 320/400 360/450 450/565 480/600 500/625 520/650 600/750 720/900 800/1000 900/1125 1000/1250

22/27.5 22/27.5 33/41 33/41 44/55 50/62 55/69 88/110 88/110 110/138 119/149 132/165 165/206 176/220 220/275 275/343 220/275 220/275 242/303 275/343 300/375 330/413 360/450 400/500 500/625 528/660 500/688 572/715 660/825 800/1000 880/1100 990/1238 1100/1375


Sound Proof/Weather Proof/Trailer Mounted DG Set Perkins Diesel Generator Set

Genset model

Engine model

Prime power KW/KVA

Standby

Fuel

Power KW/KVA

Consumption ≤g/kw.h

dimension mm

Weight kg

AP10

403D-11

7/9

8/10

248

1280×500×860

330

AP14

403D-15

10/13

11/14

248

1280×500×950

390

AP22

404D-22

16/20

18/22

237

1420×500×1000

470

AP33

1103A-33G

24/30

26/33

235

1520×650×1200

750

AP50

1103A-33TG1

36/45

40/50

235

1520×650×1200

770

AP66

1103A-33TG2

48/60

53/66

235

1520×650×1200

770

AP72

1104A-44TG1

52/65

57/72

208

1800×650×1200

840

AP88

1104A-44TG2

64/80

70/88

208

1800×650×1200

850

AP110

1104C-44TAG2

80/100

88/110

205

1850×700×1200

1120

AP150

1006TAG

108/135

120/150

208

2250×800×1280

1200

AP165

1006TAG2

120/150

132/165

208

2300×900×1560

1400

AP220

1306C-E87TAG3

160/200

176/220

207

2530×900×1560

1640

AP248

1306C-E87TAG4

180/225

198/248

201

2530×900×1560

1725

AP259

1306C-E87TAG5

188/235

207/259

203

2530×900×1560

1800

AP880

4006-23TAG3A

640/800

704/880

210

3780×1710×2200

4960

AP990

4008TAG1A

720/900

792/990

206

4800×2030×2170

7100

AP1100

4008TAG2A

800/1000

880/1100

214

4800×2030×2170

7100

AP1375

4012-46TWG2A

1000/1250

1100/1375

212

5100×2050×2400

8600

AP1650

4012-46TAG2A

1200/1500

1320/1650

200

5310×2050×2400

9500

AP1925

4016TAG

1400/1750

1540/1925

205

5900×2300×3000

14500

AP2030

4016TAG1A

1476/1845

1624/2030

205

5900×2300×3000

14500

AP2263

4016TAG2A

1646/2058

1811/2263

209

6000×2300×3000

14800


Sound Proof/Weather Proof/Trailer Mounted DG Set Doosan Daewoo Diesel Generator Sets

Genset model

Engine model

Prime power KW/KVA

Standby Power KW/KVA

Fuel Consumption ≤L/h

dimension mm

Weight kg

AD66

DB58

48/60

53/66

18.1

2100×800×1400

1100

AD96

D1146

70/88

77/96

20.8

2350×900×1300

1500

AD138

D1146T

100/125

110/138

27

2400×900×1300

1600

AD186

P086TI-1

135/169

149/186

48.4

2600×950×1450

1750

AD220

P086TI

160/200

176/220

48.4

2600×950×1450

1825

AD303

P126TI

220/275

242/303

66.2

3000×1000×1650 2200

AD344

P126TI-II

250/313

275/344

77.6

3000×1000×1650 2300

AD413

P158LE-1

300/375

330/413

102.9

3100×1390×1700 2500

AD440

P158LE

320/400

352/440

102.9

3100×1400×1800 2800

AD495

P158LE-S

360/450

396/495

109.7

3300×1400×1800 3050


Generator/Alternators

Little Introduction of An Alternator/Generator:In electricity generation, an electric generator is a device that converts mechanical energy to electrical energy. The reverse conversion of electrical energy into mechanical energy is done by a motor; motors and generators have many similarities. A generator forces electrons in the windings to flow through the external electrical circuit. It is somewhat analogous to a water pump, which creates a flow of water but does not create the water inside. The source of mechanical energy may be a reciprocating or turbine steam engine, water falling through a turbine or waterwheel, an internal combustion engine, a wind turbine, a hand crank, compressed air or any other source of mechanical energy.

Soherwardi Enterprises Pvt Ltd and Soherwardi Engineering supplies you a variety of world famous generators, from low power to high power and this is the honor of Soherwardi Enterprises Pvt Ltd and Soherwardi Engineering, our supplied generators are selected by our engineers and from well reputed manufacturers.

Our supply ability:Soherwardi Enterprises Pvt Ltd and Soherwardi Engineering can supply you various famous brands, such as:1. Leroysommer 2. Marathon 3. Stamford 4. Olympian 5. Kajieli And much more. Mostly we supply the power range from 10 kva to 2500 kva but on demand we can supply up to 4500 kva. We also provide the famous , Chinese generators with 100 % assurance of copper winding , and with best efficiency


ATS/MCU 01:

Diesel Generator Control System:-

The DEEPSEA 5110 control system is used to automatically start and stop the generator via remote control signal, configurable three position includes manual, auto and stop . Stop: stop generator/failure Manual: only green manual button to start generator Auto/remote control: Under working conditions when it is energized, automatically start generator if receiving remote control Microprocessor Control: The module features 16-bit microprocessor control and a comprehensive list of timers and pre-configured sequences. This allows demanding specifications to be achieved. Configurable expansion facilities are also provided. 02: The DEEPSEA 5220 control system is a low cost generator controller equipped with Auto start/stop functions, protections, alarms and annunciation etc,monitoring and protections include: running, over speed, high water temperature, low oil pressure, over crand, emergency stop, and low battery. All outputs function executed by a set of traditional relays which make it possible to support heavvy power handing capability, it designed to control engine by a key switch. Users only needs to switch the key to the manual position then the system will carry out whole function according to your setting. Besides, the DEEPSEA5220 control system applied with a high security continental terminal connector that provide easy plug-in and removal. SEC series Automatic Transfer Switches are an integral part of the power generation process, allowing smooth and immediate transfer of electrical current between multiple sources and the load. When the generator is operating, the transfer switch prevents dangerous feedback of current to the utility's system. It also ensures that different sources are fully synchronized before their power is combined or loads are transferred, which is imperative of safe operation. The transfer switch senses when utility power is interrupted, and starts up the generator if the utility power remains absent. In about five to ten seconds, when the generator is producing full power, the transfer switch disconnects the load from the utility and connects it to the generator, restoring electricity to the load. The transfer switch continues to monitor utility power, and when it is restored, switches the load from the generator back to the utility. Once the generator is disconnected, it goes through a cool-down routine and is automatically shut down. ATS size is availble from 30 to 3200Amp. Choosing the right ATS for the generator set,Generator Set Current: = Genset KVA*1000/Voltage/1.732 ATS Size sould be 120% of the generator set current

ATS Cuts Over System Features: For emergency power usage in building. Auto transfer switch (ATS) is essential ATS can auto transfer load from mains power supplying to emergency power When the main power supplying failure or voltage drop below 80% of normal voltage, ATS will auto start emergency generator set after a preset Time of 0-10sec(adjustable according to the users). Once generator reach reach at rated speed, the ATS will transfer the load to emergency generator sets automatically. The ATS has large variety current as well as load transform is feasible(20-2500A)


Parallel ATS

Generator Parallel Connection:-

Paralleling conditions: 1. -Generator sets should be equipped with electrical governor system -Incoming generator phase sequence must be same as main power -Voltage difference is in the limit between generator and main power -Frequency difference is in the limit between generator and main power -Frequency difference is in the limit between generator and main power -Phase angle difference is in the limit between generator and main power

1. Better reliability and continuity of electrical power: The paralleling of generator sets enhances system performance because they can stand much more load than one genset do.

1. Convenient maintenance and service: With generator sets operated in paralleling system, servicing generator sets will not interrupt emergency power to critical system.

1. More economic: 1. -Operator can manage the operating gensets according main power load. It eliminates the waste of fuel and lubrication oil while bigger power genset carry smaller load

More flexibility for future expansion: Paralleling system offer economy of installing only as much power as you need, then adding generator set as building power expands


Product Information