Page 1

MDT Datasheets 2012

Page

Contents Switch Actuators AKS/AKI NEW Switch Actuators AKS, new series Switch Actuators with current measurement AMI/AMS Switch Actuators compact AKK NEW Universal Actuators AKU Shutter Actuators JAL Heating Actuators AKH Dimming Actuator/Control device AKD DaliControl IP Gateway Binary Inputs BE, floating contacts, 230VAC, 12-24VDC Universal Interface USB Interface, IP Interfaces, Line Coupler Bus Power Supplies Temperature Controller/Sensor Room Temperature Controller 55mm/surface mounted Push Button 55mm/Push Button Plus 55mm with LED NEW Glas Push Buttons/Glas Push Buttons with temperature sensor NEW Presence Detectors ceiling mounted, new series Weather Station/Sun-/Rain Sensor VisuControl Touchpanel NEW KNX RF Line Coupler NEW KNX RF Glas Push Button with Actuator NEW KNX RF Push Button Plus 55mm with/without Actuator NEW KNX RF Switch Actuator NEW KNX RF Shutter Actuator

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

N

• knx@mdt.de •

www.mdt.de

-- Page 1 --

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Switch Actuator AKS/AKI

N

MDT Switch Actuator 4/8/12-fold, MDRC Version AKS-0416.01

Switch Actuator 4-fold

4SU MDRC, 230VAC, 16A, C-Load 100uF

AKS-0410.01

Switch Actuator 4-fold

4SU MDRC, 230VAC, 10A, C-Load 100uF

AKI-0416.01

Switch Actuator 4-fold

4SU MDRC, 230VAC, 16A, C-Load 200uF

AKS-0816.01

Switch Actuator 8-fold

8SU MDRC, 230VAC, 16A, C-Load 100uF

AKS-0810.01

Switch Actuator 8-fold

8SU MDRC, 230VAC, 10A, C-Load 100uF

AKI-0816.01

Switch Actuator 8-fold

8SU MDRC, 230VAC, 16A, C-Load 200uF

AKS-1216.01

Switch Actuator 12-fold

12SU MDRC, 230VAC, 16A, C-Load 100uF

AKS-1210.01

Switch Actuator 12-fold

12SU MDRC, 230VAC, 10A, C-Load 100uF

AKI-1216.01

Switch Actuator 12-fold

12SU MDRC, 230VAC, 16A, C-Load 200uF

The MDT Switch Actuator receives KNX/EIB telegrams and switches up to 12 independent electrical loads . Each output uses a bistable relay and can be operated manually via a push button. A green LED indicates the switching status of each channel. The outputs are parameterized individually via ETS3/4. The device provides extensive functions like logical operation, status response, block functions, central function, delay functions and staircase lighting function. Additionally the device provides several time and scene control. If the mains voltage fails, all outputs hold their current position. After bus voltage failure or recovery the relay position is selected in dependence on the parameterization. The MDT Switch Actuator has separate power supply terminals for each channel (AKS 08/12 Two contacts/phase, from Q3 each contact own phase). The MDT Switch Actuator is a modular installation device for fixed installation in dry rooms. It fits on DIN 35mm rails in power distribution boards or closed compact boxes. For project design and commissioning of the MDT Switch Actuator it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\Downloads.html

• • • • • • • • • • • • • • • • • •

AKI/AKS-08xx.01

AKI/AKS-12xx.01

Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices Push Button and LED indicator for each channel NO and NC contact operation Time functions (swich-on/switch-off delay, staircase light function) Status response (active/passive) for each channel Logical linking of binary data, 8 scenes per channel Central switching functions and block functions Programmable behavior in case of bus voltage failure or return AKI 04/08/12: Each contact has an own supply phase AKS 04: Each contact has an own supply phase AKS 08/12 Two contacts/phase, from Q3 each contact own phase AKI/AKS 04: Power supply via KNX bus AKI/AKS 08/12: Power supply 230VAC, from Q3 via KNX bus Modular installation device for DIN 35mm rails Integrated bus coupling unit 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 2 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Switch Actuator AKS/AKI AKS-0416.01 AKS-0816.01 AKS-1216.01

Technical Data

Number of outputs

4

N

AKS-0410.01 AKS-0810.01 AKS-1210.01

8

12

4

AKI-0416.01 AKI-0816.01 AKI-1216.01

8

12

4

8

12

Output switching ratings Ohmic load

16A

10A

16A/20A*

max. 100uF at 16A

max. 100uF at 10A

max. 200uF at 16A

230VAC

230VAC

230VAC

400A/150μs 200A/600μs

400A/150μs 200A/600μs

600A/150μs 300A/600μs

Incandescent lamps

2700W

2000W

3680W

Halogen lamps 230V

2500W

1500W

3680W

Halogen lamps, electronic transformer**

1000W

700W

2000W

Fluorescent lamps, not compensated

1800W

1600W

3680W

Fluorescent lamps, parallel comp.

1000W

700W

2500W

14

14

28

1.000.000

1.000.000

1.000.000

16A

10A

20A

Capacitive load Voltage Maximum inrush current Maximum load

Max. number of electronic transformers Output life expectancy (mechanical) Max. fuse per channel Permitted wire gauge

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

Screw terminal KNX busconnection terminal

0,8mm Ø, solid core

0,8mm Ø, solid core

0,8mm Ø, solid core

230VAC/50Hz

230VAC/50Hz

230VAC/50Hz

Power supply*** Power consumption

<0,3W

Operation temperature range

<0,3W

<0,3W

<0,3W

<0,4W

<0,3W

<0,3W

0 to + 45°C

0 to + 45°C

0 to + 45°C

IP 20

IP 20

IP 20

4/8/12SU

4/8/12SU

4/8/12SU

Enclosure Dimensions MDRC (Space Units)

<0,4W

<0,4W

* total current carrying capacity neighbouring outputs max. 32 A ** low voltage halogen lamps with electronic transformer *** AKI/AKS 08/12: Power supply 230VAC, from Q3 2012 via KNX Bus. AKS/AKI 04: Power supply via KNX bus

Examplary circuit diagram AKS-0816.01

Examplary circuit diagram AKI-0816.01

Note: AKI/AKS 08/12: Power supply 230VAC, from Q3 2012 via KNX Bus.

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 3 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


NEW MDT Switch Actuator AKS

N

MDT Switch Actuator 4/8/12/20-fold, MDRC Version AKS-0416.02

Switch Actuator 4-fold

4SU MDRC, 230VAC, 16A, C-Load 140uF

AKS-0816.02

Switch Actuator 8-fold

6SU MDRC, 230VAC, 16A, C-Load 140uF

AKS-1216.02

Switch Actuator 12-fold

8SU MDRC, 230VAC, 16A, C-Load 140uF

AKS-2016.02

Switch Actuator 20-fold

12SU MDRC, 230VAC, 16A, C-Load 140uF

The new AKS series offers more channels at less space. so lower costs per channel. The MDT Switch Actuator receives KNX/EIB telegrams and switches up to 20 independent electrical loads. Each output uses a bistable relay and can be operated manually via a push button. A green LED indicates the switching status of each channel. The outputs are parameterized individually via ETS3/4. The device provides extensive functions like logical operation, status response, block functions, central function, delay functions and staircase lighting function. Additionally the device provides several time and scene control. If the mains voltage fails, all outputs hold their current position. After bus voltage failure or recovery the relay position is selected in dependence on the parameterization. The MDT Switch Actuator has separate power supply terminals for each channel and are very space saving by ideal form factor. The MDT Switch Actuator is a modular installation device for fixed installation in dry rooms. It fits on DIN 35mm rails in power distribution boards or closed compact boxes. For project design and commissioning of the MDT Switch Actuator it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\Downloads.html

• • • • • • • • • • • • • • • • •

AKS-0816.02

AKS-2016.02

Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices Space saving by ideal form factor Push Button and LED indicator for each channel NO and NC contact operation Time functions (swich-on/switch-off delay, staircase light function) Status response (active/passive) for each channel Logical linking of binary data 8 scenes per channel Central switching functions and block functions Programmable behavior in case of bus voltage failure or return Each contact has an own supply phase Power supply via KNX bus Modular installation device for DIN 35mm rails Integrated bus coupling unit 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 4 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


NEW MDT Switch Actuator AKS

N

AKS-0416.02 AKS-0816.02 AKS-1216.02 AKS-2016.02

Technical Data

Number of outputs

4

8

12

20

Output switching ratings Ohmic load

16A

Capacitive load

max. 140uF at 16A

Voltage

230VAC 600A/150μs 250A/600μs

Maximum inrush current Maximum load Incandescent lamps

3000W

Halogen lamps 230V

3000W

Halogen lamps, electronic transformer*

1500W

Fluorescent lamps, not compensated

2500W

Fluorescent lamps, parallel comp.

1800W 20

Max. number of electronic transformers

1.000.000

Output life expectancy (mechanical)

16A

Max. fuse per channel Max. total current of the actuator

64A

96A

128A

192A

Permitted wire gauge 0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

Screw terminal

0,8mm Ø, solid core

KNX busconnection terminal Power supply

via KNX bus

Power consumption

<0,3W

<0,3W

<0,4W

<0,5W

0 to + 45°C

Operation temperature range

IP 20

Enclosure

4/6/8/12SU

Dimensions MDRC (Space Units) * low voltage halogen lamps with electronic transformer

Examplary circuit diagram AKS-0816.02

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 5 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Switch Actuator AMS/AMI

N

MDT Switch Actuator 4/8/12-fold with current measurement, MDRC Version AMS-0416.01

Switch Actuator 4-fold

4SU MDRC, 230VAC, 16A, C-Load 100uF, current measurement

AMI-0416.01

Switch Actuator 4-fold

4SU MDRC, 230VAC, 16A, C-Load 200uF, current measurement

AMS-0816.01

Switch Actuator 8-fold

8SU MDRC, 230VAC, 16A, C-Load 100uF, current measurement

AMI-0816.01

Switch Actuator 8-fold

8SU MDRC, 230VAC, 16A, C-Load 200uF, current measurement

AMS-1216.01

Switch Actuator 12-fold

12SU MDRC, 230VAC, 16A, C-Load 100uF, current measurement

AMI-1216.01

Switch Actuator 12-fold

12SU MDRC, 230VAC, 16A, C-Load 200uF, current measurement

The MDT Switch Actuator receives KNX/EIB telegrams and switches up to 12 independent electrical loads . Each output uses a bistable relay and can be operated manually via a push button. A green LED indicates the switching status of each channel. The outputs are parameterized individually via ETS3/4. The device provides extensive functions like logical operation, status response, block functions, central function, delay functions and staircase lighting function. Additionally the device provides several time and scene control. The MDT Switch Actuator offers current measurement for each channel and measurement of the total current. In dependence on the parameterization the measured data can be transmit in different data formats (mA/A/kW) onto the KNX bus. Additionally the device provides an hour/service interval meter. If the mains voltage fails, all outputs hold their current position. After bus voltage failure or recovery the relay position is selected in dependence on the parameterization. The MDT Switch Actuator is a modular installation device for fixed installation in dry rooms. It fits on DIN 35mm rails in power distribution boards or closed compact boxes. The MDT Switch Actuator has a separate power supply terminals for each channel. For project design and commissioning of the MDT Switch Actuator it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\Downloads.html

• • • • • • • • • • • • • • • • • •

AMS/AMI-04xx.01

AMS/AMI-08xx.01

Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices Push Button and LED indicator for each channel NO and NC contact operation Time functions (switch-on/switch-off delay, staircase light function) Status response (active/passive) for each channel Logical linking of binary data 8 scenes per channel Hour meter Central switching functions and block functions Programmable behaviour in case of bus voltage failure or return Each contact has an own supply phase Integrated current measurement (current, kWh, limit value) Power supply via KNX bus Modular installation device for DIN 35mm rails Integrated bus coupling unit 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 6 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Switch Actuator AMS/AMI AMS-0416.01 AMS-0816.01 AMS-1216.01

Technical Data Number of outputs

4

AMI-0416.01 AMI-0816.01 AMI-1216.01

8

Current measurement range

N

12

4

8

12

20mA - 16A

20mA - 16A

16A

16A

max. 100uF at 16A

max. 200uF at 16A

230VAC

230VAC

400A/150μs 200A/600μs

600A/150μs 300A/600μs

Incandescent lamps

2700W

3680W

Halogen lamps 230V

2500W

3680W

Halogen lamps, electronic transformer*

1000W

2000W

Fluorescent lamps, not compensated

1800W

3680W

Fluorescent lamps, parallel comp.

1000W

2500W

14

28

1.000.000

1.000.000

16A

16A

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

0,8mm Ø, solid core

0,8mm Ø, solid core

via KNX bus

via KNX bus

Output switching ratings Ohmic load Capacitive load Voltage Maximum inrush current Maximum load

Max. number of electronic transformers Output life expectancy (mechanical) Max. fuse per channel Permitted wire gauge Screw terminal KNX busconnection terminal Power supply Power consumption

<0,3W

<0,4W

Operation temperature range

<0,4W

<0,3W

<0,4W

0 to + 45°C

0 to + 45°C

IP 20

IP 20

4/8/12SU

4/8/12SU

Enclosure Dimensions MDRC (Space Units)

<0,4W

* low voltage halogen lamps with electronic transformer

Examplary circuit diagram AMS/AMI-0816.01

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 7 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Switch Actuator AKK

N

MDT Switch Actuator compact 2/4/8/16-fold, MDRC MDT Switch Actuator 1/2-fold, flush mounted MDT Switch Actuator 8-fold, surface mounted Version AKK-0216.01

Switch Actuator 2-fold

2SU MDRC, 230VAC, 16A

AKK-0406.01

Switch Actuator 4-fold

2SU MDRC, 230VAC, 6A

AKK-0816.01

Switch Actuator 8-fold

4SU MDRC, 230VAC, 16A

AKK-0810.01

Switch Actuator 8-fold

4SU MDRC, 230VAC, 10A

AKK-1616.01

Switch Actuator 16-fold

8SU MDRC, 230VAC, 16A

AKK-1610.01

Switch Actuator 16-fold

8SU MDRC, 230VAC, 10A

AKK-01UP.01

Switch Actuator 1-fold

Flush mounted, 230VAC, 16A

AKK-02UP.01

Switch Actuator 2-fold

Flush mounted, 230VAC, 6A

AKK-0810A.01

Switch Actuator 8-fold

Surface mounted, 230VAC, 10A

The MDT Switch Actuator AKK receives KNX/EIB telegrams and switches up to 16 independent electrical loads . Each output uses a monostable relay. The outputs are parameterized individually via ETS3/4. The device provides extensive functions like logical operation, status response, block functions, central function, delay functions and staircase lighting function. Additionally the device provides several time and scene control. If the mains voltage fails, all outputs were switched off. After mains voltage recovery the relay position will be restored. After bus voltage failure or recovery the relay position is selected in dependence on the parameterization. The MRDC Switch Actuators use a common power supply terminal for four channels. The surface mounted and flush mounted Switch Actuators have a common power supply terminal. This feature simplifies the wiring and increases clarity of the circuit. The MDT Switch Actuator AKK is available as modular installation device, surface mounted device and flush mounted device for fixed installation in dry rooms. For project design and commissioning of the MDT Switch Actuator AKK it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\downloads.html • Production in Germany, certified according to ISO 9001 AKK-0810.01 AKK-0810A.01 • Modern design • Fully compatible to all KNX/EIB devices • NO and NC contact operation • Time functions (switch-on/switch-off delay, staircase light function) • Status response (active/passive) for each channel • Logical linking of binary data • 8 scenes per channel • Central switching functions and block functions • Programmable behavior in case of bus voltage failure or return AKK-01UP.01 AKK-02UP.01 • Four contacts share one supply phase (MDRC device) • Common supply phase (UP and AP device) • Power supply 230VAC • Integrated bus coupling unit • 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 8 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Switch Actuator AKK AKK-01UP.01 AKK-02/08/1616.01

Technical Data Number of outputs

1

2

8

N

AKK-08/1610.01 AKK-0810A.01 16

8

16

AKK-02UP.01 AKK-0406.01 2

4

Output switching ratings Ohmic load Capacitive load Voltage

16A

10A**

6A**

21uF at 10A

21uF

7uF at 3A

230VAC

230VAC

230VAC

80A/150μs 40A/600μs

80A/150μs 40A/600μs

30A/150μs 15A/600μs

Incandescent lamps

2300W

1900W

1000W

Halogen lamps 230V

2000W

1400W

800W

Halogen lamps, electronic transformer

800W

500W

300W

Fluorescent lamps, not compensated

800W

500W

300W

Fluorescent lamps, parallel comp.

180W

120W

60W

3

3

1

1.000.000

1.000.000

1.000.000

16A

10A

6A

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

0,8mm Ø, solid core

0,8mm Ø, solid core

0,8mm Ø, solid core

AKK 01/02: via KNX bus AKK 08/16: 230VAC/50Hz

230VAC/50Hz

via KNX bus

Maximum inrush current Maximum load*

Max. number of electronic transformers Output life expectancy (mechanical) Max. fuse per channel Permitted wire gauge Screw terminal*** KNX busconnection terminal Power supply Power consumption

<0,5W <0,5W 0,5-2W 0,5-4W

Operation temperature range

Dimensions UP/AP (W x H x D)

0,5-4W

<0,5W

<0,5W

0 to + 45°C

0 to + 45°C

0 to + 45°C

IP 20

IP 20

IP 20

2/4/8SU

4/8SU

4SU

41mm x 41mm x 24mm

100mm x 40mm x 88mm

41mm x 41mm x 24mm

Enclosure Dimensions MDRC (Space Units)

0,5-2W

* the total current of each supply terminal should not exceed maximum output switching current. ** not suitable to switch AC outlets *** UP device with cable connections **** depends on the switching position of the output relays

Examplary circuit diagram AKK-0810.01

Examplary circuit diagram AKK-0810A.01

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 9 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


NEW MDT Universal Actuator

N

MDT Universal Actuator 8/16-fold, MDRC Version AKU-0816.01

Universalaktor 8-fold

4SU MDRC, 230VAC, 16A

AKU-1616.01

Universalaktor 16-fold

4SU MDRC, 230VAC, 16A

The MDT Universal Actuator receives KNX/EIB telegrams and can be used as Switch Actuator or Shutter Actuator. Mixed applications from Switch- and Shutter Actuator are possible. Each output uses a bistable relay and can be operated manually via a push button. A green LED indicates the switching status of each channel. Functions as Switch Actuator: The outputs are parameterized individually via ETS3/4. The device provides extensive functions like logical operation, status response, block functions, central function, delay functions and staircase lighting function. Additionally the device provides several time and scene control. If the mains voltage fails, all outputs hold their current position. After bus voltage failure or recovery the relay position is selected in dependence on the parameterization. Functions as Shutter Actuator: The outputs are parameterized individually via ETS3/4. The device provides extensive functions like status response, block functions, central function and positioning shutters, blinds and other hangings. Additionally the device provides up to 8 scenes per channel. If the mains voltage fails, all outputs are switched off. After bus voltage failure or recovery the position of the shutter is selected in dependence on the parameterization. The MDT Universal Actuator is a modular installation device for fixed installation in dry rooms. It fits on DIN 35mm rails in power distribution boards or closed compact boxes. For project design and commissioning of the MDT Universal Actuator it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\Downloads.html

• • • • • • • • • • • • • • • • • • • •

AKU-0816.01

AKU-1616.01

Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices Can be used as Switch Actuator or Shutter Actuator Mixed applications from Switch- and Shutter Actuator possible Push Button and LED indicator for each channel NO and NC contact operation Time functions (switch-on/switch-off delay, staircase light function) Status response (active/passive) for each channel Logical linking of binary data, 8 scenes per channel Central switching functions and block functions Operation mode blind/shutter programmable Travel-, pause-at-change-of-direction- and step time adjustable 1-bit automatic function and sun protection 8-bit positioning for shutter and blinds Programmable behaviour in case of bus voltage failure or return Four contacts share one supply phase Modular installation device for DIN 35mm rails Integrated bus coupling unit 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 10 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


NEW MDT Universal Actuator Technical Data

N

AKU-0816.01

AKU-1616.01

Number of Switching outputs

8

16

Number of Shutter outputs

4

8

16A

16A

max. 21uF at 16A

max. 21uF at 16A

Output switching ratings Ohmic load Capacitive load Voltage

230VAC

230VAC

80A/150μs 40A/600μs

80A/150μs 40A/600μs

Shutter motor*

600W

600W

Incandescent lamps

2300W

2300W

Halogen lamps 230V

2000W

2000W

Halogen lamps, electronic transformer**

800W

800W

Fluorescent lamps, not compensated

800W

800W

Fluorescent lamps, parallel comp.

180W

180W

3

3

1.000.000

1.000.000

16A

16A

Maximum inrush current Maximum load

Max. number of electronic transformers Output life expectancy (mechanical) Max. fuse per channel Permitted wire gauge

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

Screw terminal KNX busconnection terminal Power supply

0,8mm Ø, solid core

0,8mm Ø, solid core

230VAC/50Hz

230VAC/50Hz

<0,5-2W

<0,5-4W

0 to + 45°C

0 to + 45°C

IP 20

IP 20

4SU

8SU

Power consumption** Operation temperature range Enclosure Dimensions MDRC (Space Units) * no three-phase asynchronous

** Power consumption when operate as Shutter Actuator 0,5W. Power consumption when operate as Switch Actuator depends on relays position.

Examplary circuit diagram AKU-0816.01

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 11 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Shutter Actuator

N

MDT Shutter Actuator 2/4/8-fold, MDRC MDT Shutter Actuator 1-fold, flush mounted MDT Shutter Actuator 4-fold, surface mounted Version JAL-0206.01

Shutter Actuator 2-fold

2SU MDRC, 6A, shutter motors 230VAC up to 300W

JAL-0410.01

Shutter Actuator 4-fold

4SU MDRC, 10A, shutter motors 230VAC up to 600W

JAL-0810.01

Shutter Actuator 8-fold

8SU MDRC, 10A, shutter motors 230VAC up to 600W

JAL-0410D.01

Shutter Actuator 4-fold

4SU MDRC, 8A, shutter motors 24VDC up to 180W

JAL-0810D.01

Shutter Actuator 8-fold

8SU MDRC, 8A, shutter motors 24VDC up to 180W

JAL-01UP.01

Shutter Actuator 1-fold

Flush mounted, 6A, shutter motors 230VAC up to 300W

JAL-0410A.01

Shutter Actuator 4-fold

Surface mounted, 10A, shutter motors 230VAC up to 600W

The MDT Shutter Actuator receives KNX/EIB telegrams and controls up to 8 independent shutter or sunblind drives. Each output uses two monostable relays. The MDRC shutter Actuators can be operated manually via a push button. The outputs are parameterized individually via ETS3/4. The device provides extensive functions like status response, block functions, central function and positioning shutters, blinds and other hangings. Additionally the device provides up to 8 scenes per channel. If the mains voltage fails, all outputs are switched off. After bus voltage failure or recovery the position of the shutter is selected in dependence on the parameterization. The MRDC Shutter Actuators use a common power supply terminal for two channels. The surface mounted and flush mounted MDT Shutter Actuators have a common power supply terminal. This feature simplifies the wiring and increases clarity of the circuit. The MDT Shutter Actuator is available as modular installation device, surface mounted device and flush mounted device for fixed installation in dry rooms. For project design and commissioning of the MDT Shutter Actuator it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\Downloads.html JAL-0410.01

JAL-0410A.01

JAL-0206.01

JAL-01UP.01

• • • • • • • • • • • • • •

Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices Push Button and LED indicator for each channel ( Only MDRC device) Operation mode blind/shutter programmable Travel-, pause-at-change-of-direction and step time adjustable 1-bit automatic function and sun protection 8-bit positioning for shutter and blinds 8 scenes per channel, alarm, central- and block functions Programmable behavior in case of bus voltage failure or return Two contacts share one supply phase (MDRC device) Common supply phase (UP and AP device) Integrated bus coupling unit 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 12 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Shutter Actuator

N

JAL-0410.01 JAL-0810.01 JAL-0410A.01

JAL-0410D.01 JAL-0810D.01

JAL-0206.01 JAL-01UP.01

4/8

4/8

1/2

10A

8A

6A

230VAC

24VDC

230VAC

600W

180W

300W

1.000.000

1.000.000

1.000.000

16A

10A

10A

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

0,8mm Ø, solid core

0,8mm Ø, solid core

0,8mm Ø, solid core

230VAC/50Hz

230VAC/50Hz

via KNX Bus

< 0,5W

<0,5W

< 0,3W

0 to + 45°C

0 to + 45°C

0 to + 45°C

Enclosure

IP 20

IP 20

IP 20

Dimensions MDRC (Space Units)

4/8SU

4/8SU

2SU

100mm x 40mm x 88mm

--

41mm x 41mm x 24mm

Technical Data Number of channels Output switching ratings Ohmic load Voltage Maximum load Shutter motor* Output life expectancy (mechanical) Max. fuse per channel Permitted wire gauge Screw terminal KNX busconnection terminal Power Supply Power consumption Operation temperature range

Dimensions UP/AP (W x H x D) * no three-phase asynchronous motor

Examplary circuit diagram JAL-0410.01

Examplary circuit diagram JAL-0410D.01

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 13 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Heating Actuator

N

MDT Heating Actuator 4/8-fold, MDRC Version AKH-0400.01

Heating Actuator 4-fold

2SU MDRC, to control electrothermic valve drives 24-230VAC

AKH-0800.01

Heating Actuator 8-fold

4SU MDRC, to control electrothermic valve drives 24-230VAC

The MDT Heating Actuator receives KNX/EIB telegrams and controls up to independent electrical outputs . Each channel has its own LED indicator. Each channel supplies up to 5 electrothermic valve drives and can be parameterized individually via ETS3/4. The channels are controllable with PWM (1-bit) or 1-byte telegrams. The integrated temperature controller manages the actuating value given by external KNX temperature sensors. The temperature controller offers comfort-, night-, frost protection- and summer- /winter- operation. The MDT Heating Actuator detects mains voltage failure and has emergency operation if the cyclic telegram is missing. Additionally they provide objects for heating request and cyclic movement of the valves. The MDT Heating Actuator is a modular installation device for fixed installation in dry rooms. It fits on DIN 35mm rails in power distribution boards or closed compact boxes. For project design and commissioning of the MDT Heating Actuator it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\Downloads.html

AKH-0400.01

• • • • • • • • • • • • • • •

AKH-0800.01

Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices Each channel controls up to 5 electrothermic valve drives Controllable with 1-bit or 1-byte telegram Direct controllable by KNX temperature sensors Integrated temperature controller (PI, Two-position, PWM) Comfort-, night- and frost protection. Summer-/winter operation Emergency operation if cyclic telegram is missing Short-circuit detection of connected load Detection of 230VAC mains voltage failure Objects for heating request and cyclic movement of the valves Modular installation device for DIN 35mm rails Integrated bus coupling unit 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 14 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Heating Actuator

N

AKH-0400.01 AKH-0800.01

Technical Data Number of outputs

4/8

Output switching current 24VAC and ohmic load

500mA

230VAC and ohmic load

500mA

External switching voltage

24-230VAC

Maximum load 230VAC: 5 each channel 24VDC: 3 each channel

Number of electrotermic valves*

Triac output, wearless

Output life expectancy Permitted wire gauge

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

Screw terminal

0,8mm Ø, solid core

KNX busconnection terminal Power supply

via KNX bus

Power consumption KNX Bus

< 0,3W

Operation temperature range

0 to + 45°C

Enclosure

IP 20

Dimensions MDRC (Space Units)

2/4SU

* depends on manufacturer. Inrush current for 5 electrothermic valves has to be < 1A each electrothermic valve

Examplary circuit diagram AKH-0800.01

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 15 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Dimming Actuator

N

MDT Dimming Actuator 1/2/4-fold, MDRC Version AKD-0201.01

Dimming Actuator 2-fold

4SU MDRC, 230VAC, 250W

AKD-0401.01

Dimming Actuator 4-fold

8SU MDRC, 230VAC, 250W

AKD-0103.01

Dimming Actuator 1-fold

4SU MDRC, 230VAC, 600W

AKD-0203.01

Dimming Actuator 2-fold

8SU MDRC, 230VAC, 600W

AKD-0410V.01

Control Device 4-fold

4TE MDRC, 1-10V

The MDT Dimming Actuator receives KNX/EIB telegrams and dimms/switches up to 4 independent electrical loads. Each output can be operated manually via a push button. The outputs are for switching and dimming incandescent lamps, HV halogen lamps, LV halogen lamps (with conventionel or suitable electronic transformers), dimmable energy saving lamps and LED lightning. Leading or trailing edge principle can be chosen. The device has an integrated shortcircuit and excess temperature protection plus softstart function to increase lamp life time. Programmable performance after mains voltage failure, bus voltage failure or return. The 1-10V MDT Control Device has embedded switching relays for 30 ECG/30W, 20 ECG/58W, 15 ECG/2x36W or 10ECG/2x58W. Each channel offers control voltage up to 30 electronic transformers (ECG). The MDT Dimming Actuator is a modular installation device for fixed installation in dry rooms. It fits on DIN 35mm rails in power distribution boards or closed compact boxes. For project design and commissioning of the MDT Dimming Actuator it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\Downloads.html

AKD-0201.01

• • • • • •

AKD-0410V.01

• • • • • • •

AKD-0401.01

Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices 4W minimum load for LED lightning possible Push Button and LED indicator for each channel For dimming and switching incandescent lamps, HV halogen lamps, LV halogen lamps ( with conventional or suitable electronic transformers), dimmable energy saving lamps and LED lightning Dimming operation in leading or trailing edge Short circuit and temperature protection with alarm, softstart Time functions (swich-on/switch-off delay, staircase light function) Each contact has an own supply phase Modular installation device for DIN 35mm rails Integrated bus coupling unit 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 16 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Dimming Actuator Technical Data

AKD-0201.01 AKD-0401.01

AKD-0103.01 AKD-0203.01

2/4

1/2

230VAC

230VAC

Number of outputs Switching voltage outputs

N

Technical Data

AKD-0410V.01

Number of outputs

4

Switching voltage outputs

230VAC

Switching voltage control outputs Maximum lamp load*

250W

600W

Maximum number of ECG

Minimum lamp load**

12W

20W

Maximum current switching relais

Maximum fuse per channel

10A

10A

Maximum capacitive load

Permitted wire gauge

1-10V 30 16A 100uF

Permitted wire gauge 0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

Screw terminal

0,8mm Ø, solid core

KNX busconnection terminal Power supply

Screw terminal KNX busconnection terminal

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded 0,8mm Ø, solid core

via KNX bus

via KNX bus

Power consumption***

< 0,3W

< 0,3W

Power dissipation no load****

<0,5W

<0,5W

<4W

<8W

0 to + 45°C

0 to + 45°C

Enclosure

IP 20

IP 20

Enclosure

IP 20

Dimensions MDRC (Space Units)

4/8SU

4/8SU

Dimensions MDRC (Space Units)

4SU

Power dissipation nominal load**** Operation temperature range

Power supply Power consumption***

Operation temperature range

via KNX bus < 0,3W

0 to + 45°C

* Maximum load for dimmable energy saving lamps is 80W (AKD-xx01.01) or 200W (AKD-xx03.01) Maximum load for dimmable LED lamps is, depending on the LED lamp manufacturer, 25-80W (AKD-xx01.01) or 60-200W (AKD-xx03.01) ** Minimum load for dimmable LED lamps are 4-12W, depending on the LED lamp manufacturer *** Power consumption from KNX Bus **** Maximum power dissipation for each channel Note: Dimming Actuators AKD have separate Power supply terminals for each channel. The channel outputs can not be bridged.

Important assembly note: Conventionel transformers must be fused on primary side with adequate fuse according to the size of the transformator.

Examplary circuit diagram AKD-0201.01

Examplary circuit diagram AKD-0401.01

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 17 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Dali Gateway

N

MDT DaliControl IP Gateway with webinterface, MDRC Version SCN-DALI64.01

DaliControl IP gateway

6SU MDRC, up to 64 ECG

The MDT DaliControl IP Gateway receives KNX/EIB telegrams and enables the classic control of 16 DALI groups plus individual control of the ECG. An example is switching or dimming of 2x16 light in groups (advantage of synchronous switching inside the group) plus 32 individual lights. The MDT DaliControl IP Gateway detects light and ECG errors and releases telegrams in dependence of its parameterisation. The commisioning after installation and group attribution of the MDT DaliControl IP Gateway is done with the buttons on the device or with the integrated webinterface. Quick identification and group attribution of the connected DALI segments can be done without connection to the KNX bus. The network connection is realized with an RJ45 interface. Additionally the MDT DaliControl IP Gateway offers two binary inputs to connect push buttons or presence detectors. The MDT DaliControl IP Gateway is a modular installation device for fixed installation in dry rooms. It fits on 35mm rails in power distribution boards or closed compact boxes. For project design and commissioning of the MDT DaliControl IP Gateway it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\Downloads.html

• • • • • • • • • • • • • • • • • •

SCN-DALI64.01

Production in Germany certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices Supports diifferent light types Dimming curve matches the human perception Simultanous dimming Tracking of operating hours and switch cycles Display and reporting of light and ECG errors Simple change of the configuration without using ETS Setting of light scenes without any knx modules Simple group attribution directly on the device Dali Commissioning via Webbrowser or directly on the device display Dali Commissioning via softwaretool Individual control up to 64 EVG Operation via integrated binary inputs without knx Modular installation device for DIN 35mm rails Integrated bus coupling unit 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 18 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Dali Gateway Electrical Data

N SCN-DALI64.01

Outputs Number of groups

16

Number of ECG

64

Maximum Dali voltage

18-21VDC

Maximum Dali current

150mA

Inputs Number of inputs

2

Maximum cable lenght

15m 9-36VDC 9-24VAC

Maximum signal voltage Permitted wire gauge

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

Screw terminal

0,8mm Ø, solid core

KNX busconnection terminal Power Supply

230VAC

Power consumption

< 3W 0 bis + 45°C

Operation temperature range Enclosure

IP 20

Dimensions MDRC (Space Units)

6SU

Examplary circuit diagram SCN-DALI64.01

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 19 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Binary Input

N

MDT Binary Inputs 4/8/16-fold, MDRC Version BE-04000.01

Binary Input 4-fold

2SU MDRC, Inputs for floating contacts

BE-04024.01

Binary Input 4-fold

2SU MDRC, Inputs 24VAC/DC

BE-04230.01

Binary Input 4-fold

2SU MDRC, Inputs 230VAC

BE-08000.01

Binary Input 8-fold

4SU MDRC, Inputs for floating contac

BE-08024.01

Binary Input 8-fold

4SU MDRC, Inputs 24VAC/DC

BE-08230.01

Binary Input 8-fold

4SU MDRC, Inputs 230VAC

BE-16000.01

Binary Input 16-fold

8SU MDRC, Inputs for floating contacts

BE-16024.01

Binary Input 16-fold

8SU MDRC, Inputs 24VAC/DC

BE-16230.01

Binary Input 16-fold

8SU MDRC, Inputs 230VAC

The MDT Binary Input is available in 3 versions, input detection of 24VAC/DC signals, input detection of 230VAC signals and reading out of floating contacts. The Binary Input reacts depending on its programmed parameters and sends a telegram on the KNX bus. You can connect conventional push-buttons or auxiliary contacts (e.g. door and window contacts) to the device. The MDT Binary Inputs include four integrated logical modules to implement logical operations and logical control. These logical modules interpret all the inputs plus two external objects. So you can easily create KNX/EIB telegrams which are required in daily practice (e.g. fault telegrams or „all windows closed“). Each Input is parameterized individually via ETS3f/4. The device provides extensive functions like switching of lighting, operation of blinds and shutters, counting of pulses, debounce time, contact type and telegram rate limitation. The command for rising and falling edge can be defined independently and with the block communication object each channel can be blocked or released. The logic module can release two telegrams after receiving a trigger signal from the inputs. The MDT Binary Input is a modular installation device for fixed installations in dry rooms. It fits on DIN 35mm rails in power distribution boards or closed compact boxes. For project design and commissioning of the MDT Binary Input it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\Downloads.html

BE-04000.01

• • • • • • • • • • • • • • • •

BE-08000.01

BE-16000.01

Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices To connect conventional push buttons or window/auxiliary contacts 4 integrated logical modules Telegram rate limitation NO or NC contact operation, programmable length of button push Operation of blinds and shutters, 1 and 2 button operation Forced setting function for each output Operation with short/long button push and 2 objects Counting of pulses, suitable for 30ms S0 pulses Cyclical sending of contact state programmable Internal contact voltage 12V Modular installation device for DIN 35mm rails Integrated bus coupling unit 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 20 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Binary Input Electrical Data Number of inputs Signal voltage

BE-04000.01 BE-08000.01 BE-16000.01

BE-04230.01 BE-08230.01 BE-16230.01

BE-04230.01 BE-08024.01 BE-16024.01

4/8/16

4/8/16

4/8/16

For floating contacts

230VAC

12-24VDC / 24VAC

12V

--

--

100m

--

--

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

0,8mm Ø, solid core

0,8mm Ø, solid core

0,8mm Ø, solid core

via KNX bus

via KNX bus

via KNX bus

<0,3W

<0,3W

<0,3W

0 bis + 45°C

0 bis + 45°C

0 bis + 45°C

IP 20

IP 20

IP 20

2/4/8SU

2/4/8SU

2/4/8SU

Internal contact voltage Permitted input cable length

N

Permitted wire gauge Screw terminal KNX busconnection terminal Power Supply Power consumption Operation temperature range Enclosure Dimensions MDRC (Space Units)

Examplary circuit diagram BE-08000.01

Examplary circuit diagram BE-08024.01

Examplary circuit diagram BE-08230.01

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 21 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Universal Interface

N

MDT Universal Interface 2/4-fold, flush mounted Version BE-02001.01

Universal Interface 2-fold

Flush mounted, for floating contacts, with LED output

BE-04001.01

Universal Interface 4-fold

Flush mounted, for floating contacts, with LED output

The MDT Universal Interface is to be inserted in a wiring box or behind a push button or switch. The inputs react depending on their programmed parameters and and send a telegram on the bus. You can connect conventional push-buttons or auxiliary contacts (e.g. door and window contacts) to the device. The length of connection cables is 22cm. Each input can be set as a LED output and drive a low current LED. The MDT Universal Interface includes four integrated logical modules to implement logical operations and logical control. These logical modules interpret all the inputs plus two external objects. So you can easily create KNX/EIB telegrams which are required in daily practice (e.g. fault telegrams or „all windows closed“). Each input is parameterized individually via ETS3/4. The device provides extensive functions like switching of lighting, operation of blinds and shutters, counting of pulses, debounce time, contact typ and telegram rate limitation. The command for rising and falling edge can be defined independently and with the block communication object each channel can be blocked or released. The logic module can release two telegrams after receiving a trigger signal from the inputs. The MDT Universal Interface is a flush mounted device to be inserted in a wiring box or behind a push button or switch. It has to be installed in dry rooms. For project design and commissioning of the MDT Universal Interface it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\Downloads.html

BE-02001.01

• • • • • • • • • • • • • • • • •

BE-04001.01

Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices To connect conventional push-buttons or window/auxiliary contacts 4 integrated logical modules Telegram rate limitation NO or NC contact operation, programmable length of button push Operation of blinds and shutters, 1 and 2 button operation Forced setting function for each output Operation with short/long button push and 2 objects Counting of pulses Cyclical sending of contact state programmable Each output can be set as 1,5mA output for low current LED Flush mounted (length of connection cables: 22cm) Dimensions (W x H x D): 41mm x 41mm x 12mm Integrated bus coupling unit 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 22 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Universal Interface Electrical Data

N

BE-04000.01

BE-02000.01

4

2

0,8mm Ø, solid core

0,8mm Ø, solid core

via KNX bus

via KNX bus

<0,3W

<0,3W

Permitted input cable length

5m

5m

Operation temperature range

0 to + 45°C

0 to + 45°C

IP 20

IP 20

41mm x 41mm x 12mm

41mm x 41mm x 12mm

Number of Inputs Permitted wire gauge KNX busconnection terminal Power Supply Power consumption

Enclosure Dimensions UP (W x H x D)

Examplary circuit diagram BE-02001.01

Examplary circuit diagram BE-04001.01

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 23 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT USB/IP Interface

N

MDT Interface, MDRC Version SCN-USBR.01

USB Interface

2SU MDRC

SCN-IP000.01

IP Interface

2SU MDRC

SCN-IP100.01

IP Interface with Routing

2SU MDRC

SCN-LK001.01

Line Coupler

2SU MDRC

MDT technologies offers four KNX Interfaces to enable communication between PC and the KNX/EIB system. KNX USB Interface: The USB Interface enables the communication between the PC and the KNX/EIB system. The USB interface is galvanically isolated from the KNX/EIB bus. KNX IP Interface: The IP Interface enables the communication between the PC and the KNX/EIB system via LAN. 5 simultaneous connections possible. An external power supply (12 to 24VAC/DC) or power over ethernet is required. KNX IP Interface with routing: This interface offers the same functions as the IP Interface, but the device routes telegrams as a line coupler using the the LAN. KNX IP Line Coupler: The Line Coupler connects two KNX lines to each other. Electrical isolation between the lines and reduction of the busload by using the filter function. The MDT KNX Interfaces are modular installation devices for fixed installation in dry rooms. They fit on DIN 35mm rails in power distribution boards or closed compact boxes. For project design and commissioning of the MDT KNX Interfaces it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\Downloads.html

SCN-USBR.01

• Production in Germany, certified according to ISO 9001 • Modern design • Fully compatible to all KNX/EIB devices

SCN-LK001.01

USB Interface: • To enable bidirectional communication between PC and the KNX bus via USB • Fully compatible to ETS3f/4 IP Interface: • To enable bidirectional communication between PC and the KNX bus TCP/IP • 5 simultaneous connections possible (SCN-IP000.01 only) • Programming the KNX bus via TCP/IP • External power supply or PoE required • Modular installation device for DIN 35mm rails • Integrated bus coupling unit • 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 24 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT USB/IP Interface Electrical Data Interface

N

SCN-USBR.01

SCN-IP000.01

SCN-IP100.01

SCN-LK001.01

USB

Ethernet

Ethernet

KNX

Permitted wire gauge 0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

--

Screw terminal

--

0,8mm Ø, solid core

0,8mm Ø, solid core

0,8mm Ø, solid core

0,8mm Ø, solid core

via KNX bus

12 to 24VAC/DC

12 to 24VAC/DC

via KNX bus

< 0,3W

< 0,8W

< 0,8W

<0,3W each line

0 to + 45°C

0 to + 45°C

0 to + 45°C

0 to +45°C

Enclosure

IP 20

IP 20

IP 20

IP 20

Dimensions MDRC (Space Units)

2SU

2SU

2SU

2SU

KNX busconnection terminal Power Supply Power consumption Operation temperature range

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 25 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Power Supply

N

MDT Power Supply, MDRC Version STV-160.01

Power Supply

4SU MDRC, 160mA

STV-320.01

Power Supply

4SU MDRC, 320mA

STV-640.01

Power Supply

6SU MDRC, 640mA

The MDT KNX Power Supply with integrated choke produces the stabilized KNX system voltage (30VDC) to supply the connected KNX/EIB components. The operating status is indicated via 3 LED: • Red LED: Reset of the KNX/EIB bus • Green LED: Normal operation, no faults • Yellow LED: KNX/EIB bus overload Once the fault has been rectified, the Power Supply restarts itself. Additionally the Power Supply STV-640.01 offers a choke free output that can be used for a special battery module All devices able to supply 100% overload. The MDT KNX Power Supply is a modular installation device for fixed installation in dry rooms. It fits on DIN 35mm rails in power distribution boards or closed compact boxes.

STV-160.01

• • • • • • • • • • • • •

STV-320.01

STV-640.01

Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices KNX power supply with integrated choke Mains voltage 230VAC Short-circuit-proof 100% overload LED indicator for bus reset, normal operation and bus overload Button for bus reset on top Choke free output (STV-640.01 only) Modular installation device for DIN 35mm rails Integrated bus coupling unit 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 26 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Power Supply Technical Data

N

MDT STV-160.01

MDT STV-320.01

MDT STV-640.01

230VAC/50Hz

230VAC/50Hz

230VAC/50Hz

30VDC

30VDC

30VDC

--

--

30VDC

Nominal

160mA

320mA

640mA

Maximal

350mA

700mA

1200mA

--

--

1000mA

16A

16A

16A

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

0,8mm Ø, solid core

0,8mm Ø, solid core

0,8mm Ø, solid core

0 to + 45°C

0 to + 45°C

0 to + 45°C

Enclosure

IP 20

IP 20

IP 20

Dimensions MDRC (Space Units)

4SU

4SU

6SU

Power Supply Supply voltage KNX output voltage Choke free output voltage Output current

Max. total current of both outputs Mains fuse Permitted wire gauge Screw terminal KNX busconnection terminal Operation temperature range

Examplary circuit diagram STV-320.01

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 27 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Temperature Controller

N

MDT Temperature Controller 6-fold, MDRC MDT Temperature Controller/Sensor 6-fold, surface mounted Version SCN-RT6REG.01

Temperature Controller 6-fold 2SU MDRC

SCN-RT6AP.01

Controller/Sensor 6-fold

Surface mounted, for PT1000 sensors up to 12m cable length

Accessories SCN-RT6AP.001 SCN-PTST3.01

Sensor Standard

PT1000 sleeve probe with 3 m cable

SCN-PTAN3.01

Sensor strap on installation

PT1000 sleeve probe with 3 m cable

SCN-PTDE0.01

Sensor ceiling installation

PT1000 probe for ceiling installation

The MDT Temperature Controller is used for all purpose temperature control applications. The temperature is received as an KNX object, additionally the SCN-RT6AP.01 can manage up to 6 PT1000 temperature sensors. Depending on the adjusted parameters of the Temperature controller the actuating value is sent as 1-bit or 1-byte variable to the bus. The characteristic of the MDT Temperature Controller (Two-position, PI and PWM control) can be set in the ETS3/4. The thermostat stores the minimum and maximum temperature and releases an alarm telegram if the temperature differs from the programmed limit values. The temperature of the frost protection is parameterizable. The desired value can be given by MDT VisuControl touchpanel or the MDT pushbuttons. The MDT Temperature Controller Actuator REG is a modular installation device for fixed installation in dry rooms. It fits on DIN 35mm rails in power distribution boards or closed compact boxes. The Temperature Controller Actuator AP is a surface mounted device, the maximum length of the PT1000 temperature sensors should not exceed 12m. Both MDT Temperature Controllers are for fixed installations in dry rooms. For project design and commissioning of the MDT Temperature Controllers it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\Downloads.html

SCN-RT6REG.01

SCN-RT6AP.01

SCN-PTST3.01

SCN-PTDE0.01

• • • • • • • • • • • •

Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices Selectable temperature controller (PI,Two-position, PWM) Limit values min/max, Frost protection alarm, Memory for min/max Cyclical sending of contact state programmable Day-/night-/frost protection operation HVAC object and 1bit object to choose operation mode RHCC status and bit/byte objects to declare status Desired value can be given by visualisation, e.g. MDT VisuControl Integrated bus coupling unit 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 28 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Temperature Controller Electrical Data

N

SCN-RT6REG.01

SCN-RT6AP.01

Number of channels

6

6

Temperature sensors

--

connection for PT1000

0,8mm Ø, solid core

0,8mm Ø, solid core

via KNX bus

via KNX bus

<0,3W

<0,3W

Encosure

IP 20

IP 20

Dimensions (Space Units)

2SU

--

--

115mm x 64mm x 40mm

Permitted wire gauge KNX busconnection terminal Power supply Power consumption Operation temperature range

Dimensions (W x H x D)

Examplary circuit diagramm SCN-RT6REG.01

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 29 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT RTC

N

MDT Room Temperature Controller 1-fold, flush mounted MDT Room Temperature Controller 1-fold, surface mounted Version SCN-RT1UP.01

Room Temperature Controller 1-fold

Flush mounted, white, 55mm

SCN-TS1UP.01

Room Temperature Sensor

Flush mounted, white, 55mm

SCN-RT1UPE.01

Room Temperature Controller 1-fach with adjustment knob Flush mounted, white, 55mm

SCN-RT1APE.01

Room Temperature Controller 1-fach with adjustment knob Surface mounted, white

1-fold

The MDT Room Temperature Controller is used to control the indoor temperature, it has a working range from -10 to +50°C. The MDT Room Temperature Controller detects the temperature and releases telegrams in dependence on its parameterisation. The characteristic of the MDT Temperature Controller (Two-position, PI and PWM control) can be set in the ETS3/4. The MDT Room Temperature Controller stores the minimum and maximum temperature and releases an alarm telegram if the temperature differs from the programmed limit values. The temperature of the frost protection is parameterizable. Fits all switches with 55mm rocker: • BERKER S1, B1, B3, B7 glass • GIRA Standard 55, E2, Event, Esprit • JUNG A500, Aplus • MERTEN M-Smart, M-Arc, M-Plan The MDT Room Temperature Controller is a flush mounted device for fixed installations in dry rooms, it is delivered with support ring. For project design and commissioning of the MDT Room Temperature Controller it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\Downloads.html

SCN-RT1UP.01

SCN-RT1UPE.01

• • • •

SCN-TS1UP.01

• • • • • • • • • •

SCN-RT1APE.01

Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices Fits all switches with 55mm rocker: - BERKER S1, B1, B3, B7 - GIRA Standard 55, E2, Event, Esprit - JUNG A500, Aplus - MERTEN M-Smart, M-Arc, M-Plan Selectable temperature controller (PI,Two-position, PWM) For indoor temperature controlling, range -10° to +50°C Limit values min/max, Frost protection alarm, Memory for min/max Desired value can be given by visualisation, e.g. MDT VisuControl Day-, night- and frost protection operation HVAC object and 1bit object to choose operation mode RHCC status and bit/byte objects to declare status Installation with support ring (Included in delivery) Integrated bus coupling unit 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 30 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT RTC

N

Electrical Data

SCN-RT1UP.01

SCN-RT1UPE.01

SCN-TS1UP.01

SCN-RT1APE.01

Configuration

RTC

RTC

Temperature sensor

RTC

1

1

1

1

0,8mm Ø, solid core

0,8mm Ø, solid core

0,8mm Ø, solid core

0,8mm Ø, solid core

via KNX bus

via KNX bus

via KNX bus

via KNX bus

<0,3W

<0,3W

<0,3W

<0,3W

-10 to +50°C

-10 to +50°C

-10 to +50°C

-10 to +50°C

IP 20

IP 20

IP 20

IP 20

55mm x 55mm x 13mm

55mm x 55mm x 13mm

91mm x 85mm x 26mm

91mm x 85mm x 26mm

Number of Channels Permitted wire gauge KNX busconnection terminal Power Supply Power consumption Operating temperature range Enclosure Dimensions UP/AP (W x H x D)

Examplary circuit diagram SCN-xTxxxx.01

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 31 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Push Button

N

MDT Push Button 2/4/6/8-fold, flush mounted Version BE-TA5502.01

Push Button 2-fold

Flush mounted, white matt finish

BE-TA5504.01

Push Button 4-fold

Flush mounted, white matt finish

BE-TA5506.01

Push Button 6-fold

Flush mounted, white matt finish

BE-TA5508.01

Push Button 8-fold

Flush mounted, white matt finish

BE-TA55P2.01

Push Button 2-fold Plus

Flush mounted, white matt finish, status and orientation LED

BE-TA55P4.01

Push Button 4-fold Plus

Flush mounted, white matt finish, status and orientation LED

BE-TA55P6.01

Push Button 6-fold Plus

Flush mounted, white matt finish, status and orientation LED

BE-TA55P8.01

Push Button 8-fold Plus

Flush mounted, white matt finish, status and orientation LED

The MDT KNX Push Button releases KNX telegrams after pushing the buttons on top, 1 or 2 Button operation can be paramerized. The device provides extensive functions like switching of lighting, operation of blinds and shutters, contact type and block communication objects for each channel. The centered title block allows individually marking of the MDT KNX Push Button. You can use transparent or the lightgray film if no is marking is required. You find the marking draft in our download area. The MDT KNX Push Button from the Plus series has an additional orientation LED and a bicolored (red/green) LED for each rocker. These LED can be set from internal or external objects. The LED can display 3 situations like: LED off 0 „absent“, LED green „present“, LED red „window open“. The logic module can release a second telegrams after receiving a trigger signal from the inputs. Fits all 55mm frames: • BERKER S1, B1, B3, B7 glass • GIRA Standard 55, E2, Event, Esprit • JUNG A500, Aplus • MERTEN M-Smart, M-Arc, M-Plan The MDT KNX Push Button is a flush-mounted device for fixed installations in dry rooms, it is delivered with support ring. For project design and commissioning of the KNX Push Button it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\downloads.html BE-TA5502.01

BE-TA55P2.01

• • • •

BE-TA5508.01

• • • • • • • • •

BE-TA55P8.01

Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices Fits all switches with 55mm rocker: - BERKER S1, B1, B3, B7 - GIRA Standard 55, E2, Event, Esprit - JUNG A500, Aplus - MERTEN M-Smart, M-Arc, M-Plan Push Buttons can be parameterized for 1 or 2 button operation NO or NC contact operation, programmable length of button push Forced setting function for each output Operation with short/long button push and 2 objects Operation of blinds and shutters, 1 and 2 button operation Centered title block with cover film for individual marking Installation with support ring (included in delivery) Integrated bus coupling unit 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 32 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Push Button

N

BE-TA5502.01 BE-TA55P2.01

BE-TA5504.01 BE-TA55P4.01

BE-TA5506.01 BE-TA55P6.01

BE-TA5508.01 BE-TA55P8.01

Number of rockers

2

4

6

8

Number of bicolored LED (TA-55xxP)

2

4

6

8

Orientation LED (TA-55xxP)

1

1

1

1

0,8mm Ø, solid core

0,8mm Ø, solid core

0,8mm Ø, solid core

0,8mm Ø, solid core

via KNX Bus

via KNX Bus

via KNX Bus

via KNX Bus

<0,3W

<0,3W

<0,3W

<0,3W

0 to + 45°C

0 to + 45°C

0 to + 45°C

0 to + 45°C

IP 20

IP 20

IP 20

IP 20

Electrical Data

Permitted wire gauge KNX busconnection terminal Power supply Power consumption Operation temperature range Enclosure

55mm x 55mm x 13mm 55mm x 55mm x 13mm 55mm x 55mm x 13mm 55mm x 55mm x 13mm

Dimensions (W x H x D)

Examplary circuit diagram BE-TAxx.01

Compatible to 55mm programs Manufacturer Series Berker Berker Berker Berker Berker Berker Gira Gira Gira Gira Gira Gira Merten Merten Merten Merten Merten Merten Jung Jung Jung Jung Jung

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 33 --

B.7 Glas polarweiss B.3 Alu polarweiss S.1 polarweiss B.1 polarweiss matt B.7 Glas Alu S.1 polarweiss matt Standard 55 reinweiss seidenmatt E2 reinweiss seidenmatt Esprit Glas mint Esprit Glas weiss Event Alu Event reinweiss matt M-Smart polarweiss brillant M-Plan polarweiss edelmatt M-Arc polarweiss edelmatt Atelier-M polarweiss M-Plan Echtglas brillantweiss M-Smart polarweiss AS500 alpinweiss A500 alpinweiss A500 alpinweiss Aplus Alu A500 Alu

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


NEW MDT Glas Push Button

N

MDT Push Button 2/4/6/8-fold Plus, flush mounted Version BE-GT04W.01

Glas Push Button 4-fold Plus

Flush mounted, White, Surrounding orientation light

BE-GT04S.01

Glas Push Button 4-fold Plus

Flush mounted, Black, Surrounding orientation light

BE-GT08W.01

Glas Push Button 8-fold Plus

Flush mounted, White, Surrounding orientation light

BE-GT08S.01

Glas Push Button 8-fold Plus

Flush mounted, Black, Surrounding orientation light

The MDT Glas Push Button releases KNX telegrams after touching the sensor areas on top, 1 or 2 Button operation can be paramerized. The device provides extensive functions like switching of lighting, operation of blinds and shutters, contact type and block communication objects for each channel. For individually marking of the MDT Glas Push Button you can insert a labeling film behind the glas front. You find the marking draft in our download area. The MDT Glas Push Buttons has a surrounding orientation light LED and a bicolored (White/Red) LED for sensor area. These LED can be set from internal or external objects. The LED can display 3 situations like: LED off 0 „absent“, LED white „present“, LED red „window open“. The logic module can release a second telegrams after receiving a trigger signal from the inputs. The MDT Glas Push Button is a flush mounted device for fixed installations in dry rooms, it is delivered with support ring. For project design and commissioning of the MDT KNX Push Button it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\downloads.html

BE-GT04W.01

BE-GT04S.01

BE-GT08W.01

BE-GT08S.01

• • • • • • • • • • • • • • •

Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices Sensor areas can be parameterized for 1 or 2 button operation NO or NC contact operation, programmable length of button push Forced setting function for each output Operation with short/long button push and 2 objects White/Red LED for each sensor area Surrounding orientation light Brightness of LED adjustable via object Operation of blinds and shutters, 1 and 2 button operation Title block to insert behind glas front, labeling film included Installation with support ring (included in delivery) Integrated bus coupling unit 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 34 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


NEW MDT Glas Push Button

N

BE-GT04W.01 BE-GT04S.01

BE-GT08W.01 BE-GT08S.01

Number of sensor areas

4

8

Number of bicolored LED

4

8

Surrounding

Surrounding

0,8mm Ø, solid core

0,8mm Ø, solid core

via KNX bus

via KNX bus

<0,4W

<0,4W

0 to + 45°C

0 to + 45°C

IP 20

IP 20

92mm x 92mm

92mm x 163mm

Electrical Data

Orientation LED Permitted wire gauge KNX busconnection terminal Power supply Power consumption Operation temperature range Enclosure Dimensions (W x H)

Examplary circuit diagram BE-TAxx.01

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 35 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


NEW MDT Presence Detector

N

MDT Presence Detector, flush mounted Version SCN-P360D4.01

Presence Detector, 4 pyro detectors Light sensor (Presence 16/8m)

SCN-P360K4.01

Presence Detector, 4 pyro detectors Light sensor, constant level light intensity (Presence 16/8m)

SCN-P360D3.01

Presence Detector, 3 pyro detectors Light sensor (Presence 11/5m)

SCN-P360K3.01

Presence Detector, 3 pyro detectors Light sensor, constant level light intensity (Presence 11/5m)

SCN-P360D1.01

Presence Detector, 1 pyro detectors Light sensor (Presence 4m)

The MDT Presence Detector is available in 2 versions, Presence Detector with light sensor and Presence Detector with light sensor plus constant level light intensity. Both Presence Detectors capturing the smallest movements with their built in pyro detectors and high resolution lens. The illuminance value is measured by a sensor and can be read out directly in lux. After presence detection a 1-bit or dimming value (0...100%) is send to the bus, the sensitivity is adjustable in 10 steps. The light sensor releases a telegram if the brighness value differs from the progammed value. Additionally the MDT Presence Detector has block objects for light and HVC channel and offers a module for scene control. The MDT Presence Detector with constant level light intesity can control up to 3 light rows (SCN-P360K3.01: 1 light row). The MDT Presence Detector is a installation device for fixed installation in dry rooms, the preferred installation height is 2 up to 4 meters. 4 pyro detectors: The covered area for movement is 16m (Diameter), the covered area for presence is 8m (Diameter). 3 pyro detectors: The covered area for movement is 11m (Diameter), the covered area for presence is 5m (Diameter). 1 pyro detector: The covered area for presence is 6m (Diameter). For project design and commissioning of the MDT Presence Detector it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\Downloads.html

SCN-PM360D4.01

SCN-PM360D3.01

• • • • • • • • • • • • • •

SCN-PM360D1.01

Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices Presence detector with light sensor 4 pyro detectors plus high resolution lens Programmable sensibility (Not SCN-P360D1.01) Switching function depending on brightness and movement Brighness value can be read out Master/slave function programmable Scene functions Day/Night function, monitoring with messages 2 zone operation (SCN-P360x4.0 only) Integrated bus coupling unit 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 36 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


NEW MDT Presence Detector

N

SCN-P360D4.01 SCN-P360K4.01

SCN-P360D3.01 SCN-P360K3.01

SCN-P360D1.01

Movement

16m

11m

--

Presence

8m

5m

6m

adjustable in 10 Steps

adjustable in 10 Steps

fixed, not adjustable

360°

360°

360°

5 - 2000 Lux

5 - 2000 Lux

5 - 2000 Lux

0,8mm Ø, solid core

0,8mm Ø, solid core

0,8mm Ø, solid core

via KNX bus

via KNX bus

via KNX bus

<0,3W

<0,3W

<0,3W

0 to + 40°C

0 to + 40°C

0 to + 40°C

IP 20

IP 20

IP 20

85mm x 85mm x 38mm

75mm x 75mm x 35mm

43mm x 43mm x 30mm

Electrical data Covered area (Diameter)

Sensitivity Angular coverage Range of light sensor Permitted wire gauge KNX busconnection terminal Power supply Power consumption Operation temperature range Enclosure Dimensions (W x H xD)

Covered area SCN-P360x4.01

Covered area SCN-P360x3.01

Examplary circuit diagram SCN-P360xx.01

Covered area SCN-P360x1.01

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 37 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Brightness/Weather

N

MDT Brightness-/Weather devices Version SCN-WS3HW.01

Weather Station Home

Outdoor installation on wall or pole, flush mounted control unit

SCN-SS1H.01

Sun Sensor

Indoor installation with vacuum cup, flush mounted control unit

SCN-RS001.01

Rain Sensor

Outdoor installation, Surface mounted

MDT technologies offers three Brightness / Weather devices: Wetter Station Home: • 3 channels for sun protection to control blind/shutter • Sun protection up to 3 facades • Offers wide functions to control facades (2 switching treshold, teach in function) • Brightness value for east, south, west, twilight • Wind speed value, alarm if wind speed exceeds limit, temperature value • Suited to control facades at home • Installation on wall or pole, 5m connection cable • No additional power supply required • Integrated bus coupling unit • 3 years warranty Sun Sensor: • Brightness sensor for indoor installation • Input to connect push burron for blind control • Hysteresis and time delay programmable • Installation with vacuum cup • 2m cable to connect controlling unit • Flush mounted control unit • Operation mode 1: Installation on window without blinds • Operation mode 2: Installation on window with blinds • No additional power supply required • Integrated bus coupling unit in control unit • 3 years warranty

Rain Sensor: • Integrated, automatically heating • Heating operation by choke free output STV 640 or external 24VDC power supply • Current consumption of heating is 100mA • 5 m bus connection cable • Stainless fastening angle included in delivery • Dimensions (W x H x D): 67mm x 67mm x 29mm • Integrated bus coupling unit • 3 years warranty

For project design and commissioning of the Brightness/Weather devices it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\Downloads.html • Production in Germany, certified according to ISO 9001 SCN-SS1H.01 • Modern design • Fully compatible to all KNX/EIB devices • Integrated bus coupling unit • 3 years warranty

SCN-WS3HW.01

SCN-RS001.01

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 38 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT Brightness/Weather Technical Data Measured data

N

SCN-SS1H.01

SCN-WS3HW.01

SCN-RS001.01

Brightness

Brightness, Wind, Twilight, Temperature

Rain

0,8mm Ø, solid core

0,8mm Ø, solid core

0,8mm Ø, solid core

via KNX Bus

via KNX Bus

via KNX Bus

< 0,3W

< 0,3W

< 0,3W*

0 to + 45°C

0 to + 45°C

0 to + 45°C

IP 20

IP 20

IP 20

41mm x 41mm x 12mm

--

67mm x 67mm x 29mm

Permitted wire gauge KNX busconnection Power supply Power consumption Operation temperature range Enclosure Dimensions control unit (W x H x D) *

Without heating. Heating operation by choke free output STV 640 or external 24VDC power supply. Current consumption of heating is <100mA

Examplary circuit diagram SCN-xSxxx.01

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 39 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT VisuControl

N

MDT VisuControl Touchpanel Version VC-0701.02

7“/17,7 cm TFT Display

Flush mounted

VC-1001.02

10,4“/26cm TFT Display

Flush mounted

VC-1301.02

13,3“/33cm TFT Display

Flush mounted

VC-0401.02

4,3“/10,9cm TFT Display

Webserver, MDRC

The MDT VisuControl Touch Panel is used for the visualisation of the current building status and to control building functions . The display has a resolution of 1280 x 800 pixels (VisuControl 13,3“), 800 x 600 pixels (VisuControl 10,4“) or 800 x 480 pixels (VisuControl 7“). The operation is interactively by touching the TFT display. The webserver is available as MDRC device with an resolution of 430 x 272 pixels (VisuControl 4,3“). The VisuControl Touch Panel is individually programmable with VisuControl software. It offers standard functions like switching, dimming, shutter/blind control and extensive functions for scene control and visualizing trends (temperature, wind velocity, brightness etc.). To design your own customized screen, you can easiliy include images or user defined symbols. The VisuControl Lite software is included in delivery and contains several application examples. The internal clock in the touch panel allows to create presence simulations and timer functions. Additionally the display can log measured values. Either you can visualize them or export them to a spreadsheet. The included logical functions allow to implement logical operations and logical control. The logical functions interpret the existing telegrams. So you an easiliy create KNX/EIB telegrams which are required in daily practice (e.g. fault telegrams or „all windows closed“). The integrated LAN connection is used for programming and allows to send emails, web browsing and display RSS newsfeeds. With the VisuControl View software you can easiliy establish a remote connection and control your Touch Panel from anywhere. The KNX/EIB bus connection is provided via the bus connection terminal. The VisuControl Lite software is included in delivery, without cover frame.

VC-0701.02

VC-1001.02

VC-0401.02

VC-1301.02

• • • • • • • • • • • • •

Production certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices Individually programmable Switching and dimming, shutter/blind control Remote Access via PC, iPad, iPhone Alarm indication Logical linking of binary data Displaying trends Forwarding of informations via email VisuControl lite software and demo projects included Integrated bus coupling unit 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 40 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


MDT VisuControl Technical Data

N

VC-0401.02

VC-0701.02

VC-1001.02

VC-1301.02

Screen size

4,3’’

7’’

10,4’’

13,3’’

Resolution

480 x 272 Pixel

800 x 600 Pixel

800 x 480 Pixel

1200 x 800 Pixel

2,5mm²

2,5mm²

2,5mm²

2,5mm²

0,8mm Ø, solid core

0,8mm Ø, solid core

0,8mm Ø, solid core

0,8mm Ø, solid core

24VDC

24VDC

24VDC

24VDC

< 9W

< 10W

< 11W

< 12W

Depth

149mm

45mm

59mm

59mm

Breadth

109mm

188mm

277mm

360mm

Height

49mm

148mm

224mm

254mm

Weight

0,9kg

0,95kg

1,97kg

2,5kg

Enclosure

IP 20

IP 20

IP 20

IP 20

Permitted wire gauge Screw terminal KNX busconnection terminal Power supply Power consumption* Dimensions**

* backlight off ** with cover frame

Examplary circuit diagram VC-xx01.02

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 41 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


NEW MDT KNX RF Line Coupler

N

MDT KNX RF Line Coupler, Flush mounted Version RF-LK001.01

KNX RF Line Coupler

Flush mounted

The MDT KNX RF Line Coupler connects MDT KNX RF devices to the KNX bus. The Line Coupler offers extensive filter functions to reduce the KNX RF bus load. The Line Coupler allows bidirectional KNX RF communication in system mode to the following devices: -

KNX RF Glas Push Button Plus with Actuator 4/8-fold KNX RF Push Button Plus 2/4/6/8-fold KNX RF Push Button Plus with Actuator 2/4/6/8-fold KNX RF Switching Actuator 1/2-fold KNX RF Shutter Actuator 1-fold

The MDT KNX RF Line Coupler is available as flush mounted installation device for fixed installation in dry rooms. For project design and commissioning of the MDT KNX RF Line Coupler it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\downloads.html

• • • •

RF-LK001.01

• • • • •

Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices KNX RF line coupler to connect MDT KNX RF devices like MDT Push Button RF or MDT Glas Push Button RF Protocol KNX RF (multifrequency prepared) Flush mounted in socket Dimensions (W x H x D): 41mm x 41mm x 22mm Integrated bus coupling unit 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 42 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


NEW MDT KNX RF Line Coupler Technical Data

N

RF-LK001.01

Transmitter frequency*

868,3MHz

Range

150m

Output level

10dBm

Sensitivity

<105dBm

Permitted wire gauge 0,8mm Ø, solid core

KNX busconnection terminal Power supply

via KNX bus

Power consumption

<0,4W 0 to + 45°C

Operation temperature range

IP 20

Enclosure

41mm x 41mm x 24mm

Dimensions (W x H x D) * Multifrequency prepared

Examplary circuit diagram RF-LK001.01

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 43 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


NEW KNX RF Glas Push Button

N

MDT KNX RF Glas Push Button 2/4/6/8-fold Plus with Actuator, flush mounted Version RF-GTA4W.01 KNX RF Glas Push Button 4-fold Plus Flush mounted with Actuator, White, Surrounding orientation light RF-GTA4S.01 KNX RF Glas Push Button 4-fold Plus Flush mounted with Actuator, Black, Surrounding orientation light RF-GTA8W.01 KNX RF Glas Push Button 8-fold Plus Flush mounted with Actuator, White, Surrounding orientation light RF-GTA8S.01 KNX RF Glas Push Button 8-fold Plus Flush mounted with Actuator, Black, Surrounding orientation light The MDT KNX RF Glas Push Buttons release KNX telegrams after touching the sensor areas top, 1 or 2 Button operation can be paramerized. The device provides extensive functions like switching of lighting, operation of blinds and shutters, contact type and block communication objects for each channel. The MDT KNX RF Glas Push Button is operating in bidirectional KNX RF system mode and is perfectly suited to replace conventionel push buttons in existing installations without placing KNX bus cables. The connections to the KNX bus is realized via the MDT KNX RF Line Coupler. The integrated actuator can be set as 2-fold switching actuator or 1-fold shutter actuator. For individually marking of the MDT KNX RF Glas Push Button you can insert a labeling film behind the glas front. You find the marking draft in our download area. The MDT KNX RF Glas Push Buttons have a surrounding orientation light LED and a bicolored (White/Red) LED for sensor area. These LED can be set from internal or external objects. The LED can display 3 situations like: LED off 0 „absent“, LED white „present“, LED red „window open“. The logic module can release a second telegrams after receiving a trigger signal from the inputs. The MDT KNX RF Glas Push Button is a flushmounted device for fixed installations in dry rooms, it is delivered with support ring. For project design and commissioning of the MDT KNX RF Glas Push Button it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\downloads.html

RF-GTA4W.01

RF-GTA4S.01

RF-GTA8W.01

RF-GTA8S.01

• • • • • • • • • • • • • • • • • • • •

Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices Commisioning with ETS3/4 Bidirektional KNX RF communication in system mode Sensor areas can be parameterized for 1 or 2 button operation NO or NC contact operation, programmable length of button push Forced setting function for each output Operation with short/long button push and 2 objects Operation of blinds and shutters, 1 and 2 button operation Can be set as 2-fold switching actuator or 1-fold shutter actuator Connection via MDT KNX RF line coupler Title block to insert behind glas front, labeling film included To replace conventionel push buttons To upgrade your installation without placing KNX bus cables Power supply 230VAC Surrounding orientation light Multifrequency in preperation Installation with support ring (included in delivery) 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 44 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


NEW KNX RF Glas Push Button

N

RF-GTA4W.01 RF-GTA4S.01

RF-GTA8W.01 RF-GTA8S.01

Number of sensor areas

4

8

Number of bicolored LED

4

8

Orientation LED

1

1

868,3MHz

868,3MHz

150m

150m

10dBm

10dBm

<105dBm

<105dBm

2

4

Ohmic load

10A

10A7

Capacitive load

21uF

21uF

230VAC

230VAC

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

230VAC

230VAC

<0,4W

<0,4W

0 to + 45°C

0 to + 45°C

IP 20

IP 20

92mm x 92mm

92mm x 163mm

Electrical Data

Transmitter frequency* Range Output level Sensitivity Number of outputs Output switching ratings

Voltage Permitted wire gauge Screw terminal Power supply Power consumption Operation temperature range Enclosure Dimensions (W x H) * Multifrequency prepared

Examplary circuit diagram RF-GTA4x.01

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 45 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


NEW MDT KNX RF Push Button

N

MDT KNX RF Push Button 2/4/6/8-fach Plus, flush mounted Ausführungen RF-TA55P2.01 KNX RF Push Button 2-fold Flush mounted, white matt finish, status and orientation LED RF-TA55P4.01 KNX RF Push Button 4-fold Flush mounted, white matt finish, status and orientation LED RF-TA55P6.01 KNX RF Push Button 6-fold Flush mounted, white matt finish, status and orientation LED RF-TA55P8.01 KNX RF Push Button 8-fold Flush mounted, white matt finish, status and orientation LED RF-TA55A2.01 KNX RF Push Button 2-fold Flush mounted with Actuator, white matt finish, status and orientation LED RF-TA55A4.01 KNX RF Push Button 4-fold Flush mounted with Actuator, white matt finish, status and orientation LED RF-TA55A6.01 KNX RF Push Button 6-fold Flush mounted with Actuator, white matt finish, status and orientation LED RF-TA55A8.01 KNX RF Push Button 8-fold Flush mounted with Actuator, white matt finish, status and orientation LED The MDT KNX RF Push Button releases KNX telegrams after pushing the buttons on top, 1 or 2 Button operation can be paramerized. The device provides extensive functions like switching of lighting, operation of blinds and shutters, contact type and block communication objects for each channel. The MDT KNX RF Push Button is operating in bidirectional KNX RF system mode and is perfectly suited to replace conventionel push buttons in existing installations without placing KNX bus cables. The connections to the KNX bus is realized via the MDT KNX RF Line Coupler. The integrated actuator can be set as 2-fold switching actuator or 1-fold shutter actuator (RF-TA55Ax.01 only). The centered title block allows individually marking of the MDT KNX RF Push Button. You can use transparent or the lightgray film if no is marking is required. You find the marking draft in our download area. The MDT KNX RF Push Button has an orientation light LED and a bicolored (Red/Green) LED for the sensor area. These LED can be set from internal or external objects. The LED can display 3 situations like: LED off 0 „absent“, LED green „present“, LED red „window open“. The logic module can release a second telegrams after receiving a trigger signal from the inputs. The MDT KNX RF Push Button is a flush-mounted device for fixed installations in dry rooms, it is delivered with support ring. For project design and commissioning of the MDT KNX RF Push Button it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\downloads.html

RF-TA55P2.01

RF-TA55P4.01

RF-TA55P6.01

RF-TA55P8.01

• • • • • • • • • • • • • • • • • • • •

Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices Commissioning with ETS3/4 Bidirektional KNX RF communication in system mode Fits all switches with 55mm rocker Push Buttons can be parameterized for 1 or 2 button operation NO or NC contact operation, programmable length of button push Forced setting function for each output Operation with short/long button push and 2 objects Operation of blinds and shutters, 1 and 2 button operation 2-fold switching actuator or 1-fold shutter actuator (RF-TA55xA.01) Connection via MDT KNX RF line coupler Centered title block with cover film for individual marking To replace conventionel push buttons To upgrade your installation without placing KNX bus cables Power supply 230VAC Multifrequency in preperation Installation with support ring (included in delivery) 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 46 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


NEW MDT KNX RF Push Button

N

RF-TA55P2.01 RF-TA55P4.01 RF-TA55P6.01 RF-TA55P8.01

RF-TA55A2.01 RF-TA55A4.01 RF-TA55A6.01 RF-TA55A8.01

Number of sensor areas

2/4/6/8

2/4/6/8

Number of bicolored LED

2/4/6/8

2/4/6/8

1

1

868,3MHz

868,3MHz

150m

150m

10dBm

10dBm

<105dBm

<105dBm

--

2

Ohmic load

--

10A

Capacitive load

--

21uF

Voltage

--

230VAC

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

0,5 - 4,0mm² solid core 0,5 - 2,5mm² finely stranded

230VAC

230VAC

<0,3W

<0,3W

0 to + 45°C

0 to + 45°C

IP 20

IP 20

92mm x 92mm

92mm x 163mm

Electrical Data

Orientation LED Transmitter frequency* Range Output level Sensitivity Number of outputs Output switching ratings

Permitted wire gauge Screw terminal Power supply Power consumption Operation temperature range Enclosure Dimensions (W x H) * Multifrequency prepared

Compatible to 55mm programs Manufacturer Series Berker Berker Berker Berker Berker Berker Gira Gira Gira Gira Gira Gira Merten Merten Merten Merten Merten Merten Jung Jung Jung Jung Jung

Examplary circuit diagram RF-TA55Ax.01

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 47 --

B.7 Glas polarweiss B.3 Alu polarweiss S.1 polarweiss B.1 polarweiss matt B.7 Glas Alu S.1 polarweiss matt Standard 55 reinweiss seidenmatt E2 reinweiss seidenmatt Esprit Glas mint Esprit Glas weiss Event Alu Event reinweiss matt M-Smart polarweiss brillant M-Plan polarweiss edelmatt M-Arc polarweiss edelmatt Atelier-M polarweiss M-Plan Echtglas brillantweiss M-Smart polarweiss AS500 alpinweiss A500 alpinweiss A500 alpinweiss Aplus Alu A500 Alu

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


NEW KNX RF Switch Actuator

N

MDT KNX RF Switch Actuator 1/2-fold, Flush mounted Version RF-AKK1UP.01

KNX RF Switch Actuator 1-fold

Flush mounted, 230VAC, 16A

RF-AKK2UP.01

KNX RF Switch Actuator 2-fach

Flush mounted, 230VAC, 6A

The MDT KNX RF Switch Actuator receives KNX/EIB telegrams and switchs up to 2 independent electrical loads. Each output uses a monostable relay. The outputs are parameterized individually via ETS3/4. The device provides extensive functions like logical operation, status response, block functions, central function, delay functions and staircase lighting function. Additionally the device provides several time and scene control. The MDT KNX RF Switch Actuator is operating in bidirectional KNX RF system mode and is perfectly suited for using in conventionel installations without placing KNX bus cables. The connections to the KNX bus is realized via the MDT KNX RF Line Coupler. If the mains voltage fails, all outputs were switched off. After mains voltage recovery the relay position will be restored. After bus voltage failure or recovery the relay position is selected in dependence on the parameterization. The MDT KNX RF Switch Actuator is available as flush mounted installation device for fixed installation in dry rooms. For project design and commissioning of the MDT KNX RF Switch Actuator it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\downloads.html

RF-AKK1UP.01

• • • • • • • • • • • • • • • • • •

RF-AKK2UP.01

Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices Commissioning with ETS3/ETS4 Bidirectional KNX RF communication in system mode NO and NC contact operation Time functions (switch-on/switch-off delay, staircase light function) Status response (active/passive) for each channel Logical linking of binary data 8 scenes per channel Central switching functions and block functions Programmable behavior in case of bus voltage failure or return Flush mounted in socket Connection via MDT KNX RF Line Coupler To upgrade your installation without placing KNX bus cables Power supply 230VAC Dimensions (W x H x D): 41mm x 41mm x 22mm) 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 48 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


NEW KNX RF Switch Actuator Technical Data

N

RF-AKK1UP.01

RF-AKK2UP.01

1

2

868,3MHz

868,3MHz

150m

150m

10dBm

10dBm

<105dBm

<105dBm

16A

6A

21uF at 10A

7uF at 3A

Number of outputs Transmitter frequency* Range Output level Sensitivity Output switching ratings Ohmic load Capacitive load Voltage

230VAC

230VAC

80A/150μs 40A/600μs

30A/150μs 15A/600μs

Incandescent lamps

2300W

1000W

Halogen lamps 230V

2000W

800W

Halogen lamps, electronic transformer

800W

300W

Fluorescent lamps, not compensated

800W

300W

Fluorescent lamps, parallel comp.

180W

60W

3

1

1.000.000

1.000.000

16A

6A

0,8mm Ø, solid core

0,8mm Ø, solid core

230VAC/50Hz

230VAC/50Hz

<0,3

<0,3W

0 to + 45°C

0 to + 45°C

IP 20

IP 20

41mm x 41mm x 24mm

41mm x 41mm x 24mm

Maximum inrush current Maximum load

Max. number of electronic transformers Output life expectancy (mechanical) Max. fuse per channel Permitted wire gauge KNX busconnection terminal Power supply Power Consumption Operation temperature range Enclosure Dimensions (W x H x D) * Multifrequency prepared

Examplary circuit diagram RF-AKK1UP.01

Examplary circuit diagram RF-AKK2UP.01

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 49 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


NEW KNX RF Shutter Actuator

N

MDT KNX RF Shutter Actuator 1-fold, Flush mounted Version RF-JAL1UP.01

KNX RF Shutter Actuator 1-fold

Flush mounted, 230VAC, 6A

The MDT KNX RF Shutter Actuator receives KNX/EIB telegrams and controls 1 independent shutter or sunblind drives. The output uses two monostable relays. The output is parameterized individually via ETS3/4. The device provides extensive functions like status response, block functions, central function and positioning shutters, blinds and other hangings. Additionally the device provides up to 8 scenes per channel. The MDT KNX RF Shutter Actuator is operating in bidirectional KNX RF system mode and is perfectly suited for using in conventionel installations without placing KNX bus cables. The connections to the KNX bus is realized via the MDT KNX RF Line Coupler. If the mains voltage fails, all outputs were switched off. After mains voltage recovery the relay position will be restored. After bus voltage failure or recovery the relay position is selected in dependence on the parameterization. The MDT KNX RF Shutter Actuator is available as flush mounted installation device for fixed installation in dry rooms. For project design and commissioning of the MDT KNX RF Shutter Actuator it is recommended to use the ETS3f/ETS4 or later. Please download the application software at www.mdt.de\downloads.html

• • • • • • • • • • • • • • • • •

RF-JAL1UP.01

Production in Germany, certified according to ISO 9001 Modern design Fully compatible to all KNX/EIB devices Commissioning with ETS3/ETS4 Bidirectional KNX RF communication in system mode Operation mode blind/shutter programmable Travel-, pause-at-change-of-direction- and step time adjustable 1-bit automatic function and sun protection 8-bit positioning for shutter and blinds 8 scenes per channel Programmable behavior in case of bus voltage failure or return Flush mounted in socket Connection via MDT KNX RF Line Coupler To upgrade your installation without placing KNX bus cables Power supply 230VAC Dimensions (W x H x D): 41mm x 41mm x 22mm) 3 years warranty

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 50 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606


NEW KNX RF Shutter Actuator Technical Data

N

RF-JAL01UP.01

Number of outputs

1

Transmitter frequency*

868,3MHz

Range

150m

Output level

10dBm

Sensitivity

<105dBm

Output switching ratings Ohmic load

6A

Voltage

230VAC

Maximum load 300W

Shutter motor*

1.000.000

Output life expectancy (mechanical)

16A

Max. fuse per channel Permitted wire gauge

0,8mm Ø, solid core

KNX busconnection terminal Power supply

230VAC/50Hz

Power consumption

<0,3 0 to + 45°C

Operation temperature range

IP 20

Enclosure

41mm x 41mm x 24mm

Dimensions (W x H x D) * Multifrequency prepared ** no three-phase asynchronous motor

Examplary circuit diagram RF-JAL1UP.01

MDT technologies GmbH • 51766 Engelskirchen • Papiermühle 1 Tel.: + 49 - 2263 - 880 Stand: 0312

• Fax:

+ 49 - 2263 - 4588

• knx@mdt.de •

www.mdt.de

-- Page 51 --

DIN EN ISO 9001

TAW Cert Zert.Nr.1905606

MDT Technologies  
Read more
Read more
Similar to
Popular now
Just for you