Page 1

M32-2


Serie M32-2

Sliding glass enclosures

The glass panels protect the terrace without spoiling the panoramic view Not 100% hermetic

Considerations to be taken into account with the Moviglass Series M32 sliding enclosure: - Maximum width of each panel is 700 mm. - Maximum height of the enclosure is 2,700 mm. - Maximum weight of 300 kg at one stacked end. - Maximum number of folding panels stacked at one side, depending on the width of the panel, is: Width > 450 mm: 4 panels per ejector. Maximum of 8 panels stacked to one side. Width > 550 mm: 5 panels per ejector. Maximum of 10 panels stacked to one side. Width > 650 mm: 6 panels per ejector. Maximum of 12 panels stacked to one side. Width = 700 mm: 7 panels per ejector. Maximum of 14 panels stacked to one side. Consequently the maximum number of folding panels stacked to one side is 14. This means that, if there are more panels, then they will have to be stacked on both sides, bearing in mind that the maximum weight of panels stacked on any given side must not be greater than 300 kg. - For lacquered RAL range finishes, anodised or imitation wood grain, consult price. - For any type of opening angle, consult price. - Before measuring up, check, where the enclosure is going to be installed, whether there is a railing, masonry columns or any other exterior or interior obstacle, as such will have to be indicated in order to ensure correct manufacture. - Although these are technically possible it is better to avoid angle-passing solutions. - It is possible to have the track either built into and flush with or superimposed on the surface. The following risk factors must be taken into account for installations: - Wind pressure in the area. - Height of the installation from the floor, as the following will depend on it: glass thickness, number and dimension of panels and, should such be the case, the installation of an alternative system will be recommended.


Sliding glass enclosures Tempered glass: - Is more resistant and less flexible than ordinary glass, e.g. in its response to gusts of wind or sharp knocks. - In cases of breakage the glass will shatter into fragments without sharp edges and will not cause injuries. - Tempered glass, without machining, avoiding the risk of breakage. Advantages for users: - Do not have vertical members. - By using MOVIGLASS enclosures you will minimise the maintenance requirements of terraces. - Protects from wind, noise or other inconveniences that prevent you from enjoying your terrace all year round. - Complete opening of the glass panels. - Cleaning the panels is easy and safe. - You will increase the temperature, taking advantage of the sun’s heat. - You can take advantage of the space without any visual obstacles. Specific instructions: - When the panels are stacked to one side all of their weight will be supported by a small part of the top frame. Make sure that this is firmly attached, as it is of vital importance for the operation of the enclosure. Hermetic: While the glass panels provide protection against rain and wind the system is not 100% hermetic, as the terrace must have sufficient ventilation to avoid condensation resulting from humidity. Ventilation: The gaps between the panels must be 4 to 5 mm, to ventilate the terrace. In those cases where there is wind pressure it is advisable not to fit the seals between the glass panels, in order to conserve the safety margins. Two-tone: This is the only system on the market that allows for two-tone finishes. Respect the exterior aesthetics of the façade. The enclosure can also be adapted to the interior decor.

Serie M32-2


Serie M32-2

Sliding glass enclosures

TYPES OF OPENING Depending on the width of the panels, the maximum number of panels that can be stacked to one side is: Width > 450 mm: 8 panels for 2 ejectors. Width > 550 mm: 10 panels for 2 ejectors. Width > 650 mm: 12 panels for 2 ejectors. Width = 700 mm: 14 panels for 2 ejectors. The enclosure can be adapted to the interior decor.

de 90ยบ a 180

de 90ยบ a 180

de 90ยบ a 180

Plan view Maximum height 2.700 mm Maximum panel width 700 mm Maximum number of ejectors 2 on each side Maximum number of panels 14 Maximum weight 300 kg


SERIE M32 - 2 Tempered glass enclosures, without vertical members, made up of independent panels, allowing for full opening as they can be folded away and stacked at either end. Available in tempered glass with thicknesses of 6, 8 or 10 mm and polished edges allowing for safe handling.

51 mm

161 mm

96 mm

164 mm

97 mm

51 mm

69 mm 25 mm

51 mm 35 mm Section Bottom Frame

Section Full Frame

The panels open towards the interior and the bottom frame can either be superimposed or built into and flush with the floor. The members are fitted with horizontal spacers to compensate for any small level changes. Available in lacquered finishes (210 tonalities from the RAL Classic range), decorated in imitation wood grain and lacquered to simulate an anodised finish. All of the visible accessories are also lacquered in the same finish as the members.

Includes : - Horizontal compensators. - Transparent seals between glass panels. Optional: - Side frames and compensators.


SERIE M32 - 2 Tempered glass enclosures, without vertical members, made up of independent panels, allowing for full opening as they can be folded away and stacked at either end. Available in tempered glass with thicknesses of 6, 8 or 10 mm and polished edges allowing for safe handling.

51 mm

161 mm

96 mm

164 mm

97 mm

51 mm

69 mm 25 mm

51 mm 35 mm Section Bottom Frame

Section Full Frame

The panels open towards the interior and the bottom frame can either be superimposed or built into and flush with the floor. The members are fitted with horizontal spacers to compensate for any small level changes. Available in lacquered finishes (210 tonalities from the RAL Classic range), decorated in imitation wood grain and lacquered to simulate an anodised finish. All of the visible accessories are also lacquered in the same finish as the members.

Includes: - Horizontal compensators. Opcional: - Side frames and compensators. - Transparent seals between glass panels.


SERIE M32 - 2 Tempered glass enclosures, without vertical members, made up of independent panels, allowing for full opening as they can be folded away and stacked at either end. Available in tempered glass with thicknesses of 6, 8 or 10 mm and polished edges allowing for safe handling.

51 mm

161 mm

96 mm

164 mm

97 mm

51 mm

69 mm 25 mm

51 mm 35 mm

Section Bottom Frame

Section Full Frame

The panels open towards the interior and the bottom frame can either be superimposed or built into and flush with the floor. The members are fitted with horizontal spacers to compensate for any small level changes. Available in lacquered finishes (210 tonalities from the RAL Classic range), decorated in imitation wood grain and lacquered to simulate an anodised finish. All of the visible accessories are also lacquered in the same finish as the members.

Includes : - Horizontal compensators. - Transparent seals between glass panels. - Side frames and compensators.


SERIE M32 - 2 BICOLOR Tempered glass enclosures, without vertical members, made up of independent panels, allowing for full opening as they can be folded away and stacked at either end. Available in tempered glass with thicknesses of 6, 8 or 10 mm and polished edges allowing for safe handling.

51 mm

161 mm

96 mm

164 mm

97 mm

51 mm

69 mm 25 mm

51 mm 35 mm Section Bottom Frame

Section Full Frame

The panels open towards the interior and the bottom frame can either be superimposed or built into and flush with the floor. The members are fitted with horizontal spacers to compensate for any small level changes. Available in lacquered finishes (210 tonalities from the RAL Classic range), decorated in imitation wood grain and lacquered to simulate an anodised finish. All of the visible accessories are also lacquered in the same finish as the members.

Includes : - Horizontal compensators. - Transparent seals between glass panels. Optional: - Side frames and compensators.


SERIE M32 - 2 BICOLOR Tempered glass enclosures, without vertical members, made up of independent panels, allowing for full opening as they can be folded away and stacked at either end. Available in tempered glass with thicknesses of 6, 8 or 10 mm and polished edges allowing for safe handling.

51 mm

161 mm

96 mm

164 mm

97 mm

51 mm

69 mm 25 mm

51 mm 35 mm Section Bottom Frame

Section Full Frame

The panels open towards the interior and the bottom frame can either be superimposed or built into and flush with the floor. The members are fitted with horizontal spacers to compensate for any small level changes. Available in lacquered finishes (210 tonalities from the RAL Classic range), decorated in imitation wood grain and lacquered to simulate an anodised finish. All of the visible accessories are also lacquered in the same finish as the members.

Includes : - Horizontal compensators. Optional: - Transparent seals between glass panels. - Side frames and compensators.


SERIE M32 - 2 BICOLOR Tempered glass enclosures, without vertical members, made up of independent panels, allowing for full opening as they can be folded away and stacked at either end. Available in tempered glass with thicknesses of 6, 8 or 10 mm and polished edges allowing for safe handling.

51 mm

161 mm

96 mm

164 mm

97 mm

51 mm

69 mm 25 mm

51 mm 35 mm

Section Bottom Frame

Section Full Frame

The panels open towards the interior and the bottom frame can either be superimposed or built into and flush with the floor. The members are fitted with horizontal spacers to compensate for any small level changes. Available in lacquered finishes (210 tonalities from the RAL Classic range), decorated in imitation wood grain and lacquered to simulate an anodised finish. All of the visible accessories are also lacquered in the same finish as the members.

Includes : - Horizontal compensators. - Transparent seals between glass panels. - Side frames and compensators.


Profile

Serie M32-2

78

78,5

44,4

34

40

40

Reference Description

40

22,6

50009

50002

50003

50004-B

Top Frame

Full Frame

Side frame

Glass panel 1

55,8

57,5

48 25

30,9

Reference Description

5,3

50,7

78,5

50005

50006

35507

35102

Glass panel 2

Glass panel cover 3

Compensator

Bottom Frame


Two-tone members

Serie M32-2 B

78

78,5

44,4

34

40

40

50009

Reference

Top frame

Description

55,8

40

50002

50003

Full Frame

57,5

22,6

50004-B

Side frame

Glass panel 1

49,5 25

30,9

Reference Description

5,3

50,7

78,5

50005

50006

50007

35102

Glass panel 2

Glass panel cover 3

Two-tone compensator

Bottom frame


Two-tone members

Serie M32-2 B

81 50,8

40

9

Reference Description

5

50102

50103

Top and bottom glass frame cover

Glass side frame cover

5

50107 Two-tone glass U-cover


MEASURING UP The measurements must be taken of the span of the opening to be enclosed, taking as a reference the smallest measurements between the vertical (H = Height) and horizontal (L = Length) parallels.

LEVEL CHANGE U-PIECE Remove the enclosure emplacement levels, bolt on the top and bottom level change U-pieces checking the exterior drains. In the case of side frames see the complements sheet.

These measurements are to be expressed in millimetres, bearing in mind that any member or pillar that is installed will alter the final measurement. The solidity of the top part of the gap will be taken especially into account, with a view to the perfect anchorage of the top frame, given that the full weight of the enclosure must be supported by it.


TOP FRAME Insert the top frame into the level change U-pieces and level them using an allen key and the spacers that are incorporated into the frame. Once levelled make them up. The perfect levelling of this frame is very important as it is basic to the way the system operates.

Note: For important level changes that cannot be compensated for by the spacer fitted to the top frame, fix sideways as shown in the diagrams using DIN 7981, 4.8 X 16 mm bolts.

Clean the interior of the sliding tracks well to eliminate filings.

69 mm


BOTTOM FRAME Insert the bottom frame into the level change frame and, using the spacers incorporated into the frame and the gauge line up the bottom frame parallel to the top frame (which has already been levelled). If no side frames are included see the complements sheet.

Gauge

NUMBER OF PANELS The panels are numbered according to the direction in which they fold away, which means if they are stacked on the left the numbering on the panels will run from left to right.

1st PANEL Inserting the first panel in the mortising of the frame and slide it to the stacking end until it comes up against the top stop.


Make up the stop in the holes located to that end in the top frame.

Check the level of the panel and locate the bottom stop and then fit it into place, using the holes located to that end in the bottom frame.

Having fitted the first panel, set it at 90째 to the frame and make up the retainer onto the top frame so that the panel hangs perpendicular to the frames. It is very important to fit this stop to ensure the correct operation of the enclosure.

90째


INSERTING THE REST OF THE PANELS Insert the panels in reverse folding order. Start with panel no. 4, then panel no. 3 and finally panel no. 2.

FRAME COVERS Fit the ejector cover to the top member and the bottom cover in its corresponding frame. Bear in mind the position of the ejector, depending on the folding of the panels. Check the folding and operation of the panels by working the knob to unblock the first panel. Once this has been done clean off any possible filings that may have been formed.

Fold away and stack to the left

2

3

4

1

2

Fold away and stack to the right

3

4

INSTALLATION INSTRUCTIONS The axle of the opening wheel must make contact with the long wing of the ejector. (Move the wheel sets if required) NOTE: When the enclosure, has in the side two ejectors, the first in install over the top frame is the one that has the wheel entrance lower, and the second the one that has this entrance more above.


INSTALLATION INSTRUCTIONS If the panels are not correctly levelled and there are gaps between them, either at the bottom or the top, it is because they have not been correctly levelled at this specific point. This problem can be solved by levelling the top frame along its whole length.

The panels do not close at the bottom

HINGE PIN Make absolutely sure that the hinge pin acts on the hinge in parallel and, at the same time, at both top and bottom of the panel.

The panels do not close at the top

The frame is perfectly level along its whole length.


COMPLEMENTS: U-PIECE COMPENSATION + SIDE FRAMES Fitting the U-piece compensation.

Fitting the horizontal frames

Once the horizontal U-pieces have been fitted measure the gap and cut the side U-piece to fit It between the horizontal U-pieces.

After fixing the top and bottom frames fit the side frames, fixing them with spacers.

Lu


COMPLEMENTS: TRANSPARENT SEALS Finally, fit the transparent seals to the corresponding panels, fixing them in place with neutral silicon.

JUN004 --> 10 mm glass panel JUN006 --> 6 and 8 mm glass panel

JUN003 --> 10 mm glass panel JUN005 --> 6 and 8 mm glass panel

JUN007 --> 8 mm glass panel

JUN009 --> 10 mm glass panel JUN010 --> 6 and 8 mm glass panel


Tech Catalogue Moviglass M32-2 ENG  

Tech Catalogue Moviglass M32-2 ENG