Page 1

PROFESSIONAL

R I A P E R N O I S I L COL S L O O T Y D O B O T U A &

SL16352 1


METAL-CUTTING

Drill

OVERVIEW

ATTACHMENT TURBOSHEARS

s e h c a t t a y l Quick a drill or ou to river y d t c a imp eady own! alr

TSHD1

18 Gauge Metal-Cutting

360˚ 360º Rotating Head secures in any position for optimum tool clearance and material flow.

Malco’s autobody tools are available either as attachments to your own corded or cordless drill, or for use with your air supply. You will be expert an using them within a few minutes. The highly adaptable attachments come with built-in adjustable locking drill clamps. When done, simply un-chuck the attachment and return the drill for other tasks.

Easy to Use! Long-life, dual ball bearings

Power-groove drive shaft with non-slip flats

DRILL / DRIVER REQUIREMENTS: 1/4 inch (6.35 mm) Chuck, Min. 14.4V - DC, Max 7A-AC Replaceable blades

METAL CUTTING • QUARTER PANEL HEMMING • DOOR SKIN REMOVAL • DOOR SKIN HEMMING 1


METAL-CUTTING TURBOSHEARS

20 GAUGE DRILL ATTACHMENT

TS1C

U.S. Patent No. D488,695

Rugged, inexpensive and a breeze to use, the original TurboShear requires only 1/4 inch (6.35 mm) 1200 rpm drill to operate. • Cuts straight and to the left for tight round and square body patches. • Cuts thick plastic bumpers. • Two-hand operation with hand peg. • Lateral blade adjustment ensures optimum cutting performance for life of blades.

TSDCC

OPTIONAL CLAMP FOR ONE HAND OPERATION Rotating Collar Feature not applicable on TS1C

18 GAUGE DRILL ATTACHMENT For heavy-duty jobs, wide-opening jaws easily navigate body panels and layered metal.

TSHD1

U.S. Patent No. 7,093,365

Drill Not Included.

• One-hand operation requires minimal force to cut. • Cuts straight and to the left for tight round and square body patches. • Operates at high or low speeds for maximum control and precision. • Lateral blade adjustment ensures optimum cutting performance for life of blades.

360˚

Cut body panels or remove damaged areas with ease! Make cleaner and more precise cuts than with a corded power shear at a fraction of the cost. Cut easily right down a line, make sharp turns, and even cut circles in steel, aluminum, rubber, or plastic. Cleaner and safer than a grinder and less stressful than using manual shears. There’s no dust, debris, or thin metal strip creation and no heat, no melted coatings. A good choice for shops working on both aluminum and steel vehicles.

2


New

METAL-CUTTING TURBOSHEARS

DOUBLE-CUT DRILL ATTACHMENT Easily attaches to any drill or impact driver for clean shearing on both edges of the cut. • Cuts up to 18-gauge (1.22 mm) automotive steel. • Makes clean cuts on both edges as scrap spirals out of tool path. • Cleanly disengages from cut without pulling scrap through tool head.

TSMD1

U.S. Patent No. 7,093,365

Drill Not Included.

360˚ 360º Rotating Head secures in any position for optimum tool clearance and material flow.

DRILL / DRIVER REQUIREMENTS: 1/4 inch (6.35 mm) Chuck, Min. 14.4V - DC, Max 7A-AC

3

Easy to Use!


METAL-CUTTING TURBOSHEARS

16 GAUGE DRILL ATTACHMENT Cuts all automotive-grade sheet steel from trunk pans to floor boards.

TSA1

• Helical (spiral shaped) foot for easy left, right or straight cuts.

U.S. Patent No. 7,093,365

Drill Not Included.

• Five-position, adjustable head cuts through profiles and into corners. • Adjustable blade-insert clearance ensures optimum cutting performance for life of blades. • Long-life, 4-sided blade inserts are easily replaced without head disassembly.

The ideal tool for body panels of vintage cars.

Flexibility – even in tight spots. A five position 0 to 90 degree (0, 22.5, 45, 67.5 and 90) adjustable head angle makes these 16-gauge metal-cutting

5

drill attachments exceptionally maneuverable and accessible for cuts through profiles and into tight spaces.

LOCKING POSITIONS

METAL-CUTTING DRILL ATTACHMENT TURBOSHEARS TOOL

CAPACITY

WEIGHT

REPLACEMENT PARTS

TS1C

Metal-Cutting 20 gauge (0.91 mm) 1.6 lbs (0.73 kg) Drill Attachment Turboshear

TS1RBC (Blades)

TSHD1

Metal-Cutting 18 gauge (1.22 mm) 2.2 lbs (1.00 kg) Drill Attachment Turboshear

TSHDRBC (Blades)

TSMD1 Double Cut Drill Attachment Turboshear

18 gauge (1.22 mm)

2.6 lbs (1.17 kg)

TSMDRBC (Blades)

TSA1 Metal-Cutting Drill Attachment Turboshear

26-16 gauge (0.42-1.52 mm)

3.3 lbs (1.50 kg)

TSA1RB (Cutter Bits)

TSCGC

TurboShear Chuck Guard

.06 lbs (0.03 kg)

TSDCC

TurboShear Drill Clamp

.73 lbs (0.33 kg)

4


DOOR SKIN TURBOXTOOLS

DOOR SKIN REMOVAL DRILL ATTACHMENT Keep it clean! No more dust, dirt or burns on door frame from time-consuming grinding.

DSR1

U.S. Patent No. 7,093,365

Drill Not Included.

• Lateral blade adjustment ensures optimum cutting performance for life of blades. • Long lasting blades are easily replaceable.

360˚

SPACER BAR

Narrow working head with spacer bar, cuts through rounded edge of door hem.

Expect safer removal of door skins because this tool’s built-in guide helps you gauge the right cutting depth. A pad keeps you from accidentally cutting into and damaging the inner material of the door frame. Dust, dirt, and sparks are eliminated during the cutting process. Safer than using a grinder for removing door skins while avoiding the risk of burn marks from grinder sparks. This tool is ideal in shops working with aluminum vehicles, as it does not generate airborne dust that can cross contaminate body panels.

DOOR SKIN HEMMING DRILL ATTACHMENT

DHT1

U.S. Patent No. 7,093,365

Drill Not Included.

Provide a tight, clean hemmed door edge with speed, precision and limited manual tacking. • Easily one-hand operation. • High impact, ABS polymer anvil will not scratch or mar the replacement door skin. • Resistant to solvents and easily cleaned of any panel adhesive.

Anvil guides head without marring or scratching finished side of door. FOR FACTORY-LIKE FINISH!

360˚ Slightly angling lip of replacement door skin with a hammer and dolly and flattening point of entry ensures a smooth operation.

Replace door skins to a door frame quickly with a rolled hem that looks very similar to the original factory hem. Customers will be happy when they see how great their repaired doors look. No risk of denting, scratching, or marring the door skin’s surface. Handle different door thicknesses as the tool properly aligns the skin and frame. Any adhesive residue is easily removed from the tool.

5


QUARTER PANEL TURBOXTOOLS

QUARTER PANEL HEMMING DRILL ATTACHMENT

Bend and close wheel arc flanges of replacement quarter panels with powered precision. • Quickly hem quarter panels on late model cars with a range of wheel arc flange widths up to 3/4 inch (19.05 mm). • Anvil and hammer head may be cleaned of any adhesive residue from hemming operation using a common solvent. • Long wearing anvil and hammer are easily replaced on the job.

QHT1

U.S. Patent No. 7,093,365

Drill Not Included.

Replicates a hammer and dolly motion at high speed, with precision, less fatigue and faster results. 360˚

Bull nose face orientation: Tighten lower set screw to secure head. Use rounded bull nose face to roll over flange.

Hem replacement quarter panels on late model cars up to 80% faster! Save time and get better looking results when replacing rear quarter panels on late model vehicles. Expect to finish in five to eight minutes, up to 80% faster than using a hammer and dolly. While you work, you stand outside the vehicle with a clear view of what you are doing. Risks of scratching, denting, or marring the car during hemming are eliminated. This means no need for rework, another time saver. Any adhesive residue is easily removed from the tool.

Flat face orientation: Tighten striking angle before tightening head. Use flat face to close and seal seam.

DOOR SKIN REMOVAL & HEMMING DRILL ATTACHMENT TURBOSHEARS TOOL

CAPACITY

WEIGHT

REPLACEMENT PARTS

DSR1

Door Skin Removal 20 gauge (0.91 mm) 2.2 lbs (1.00 kg) Drill Attachment Turboshear

DSR1RB (Blades)

DHT1

Door Skin Hemming 20 gauge (0.91 mm) 2.8 lbs (1.27 kg) Drill Attachment Turboshear

DHTRA (Anvil)

QHT1

Quarter Panel Hemming 28-22 gauge (0.38-0.76 mm) 2.3 lbs (1.04 kg) Drill Attachment Turboshear

QHT1RA (Anvil) QHT1RH (Hammer)

TSCGC

TurboShear Chuck Guard

.06 lbs (0.03 kg)

TSDCC

TurboShear Drill Clamp

.73 lbs (0.33 kg)

6


METAL-CUTTING

Air

OVERVIEW

POWERED TURBOSHEARS

TSHD1A1 18 Gauge Metal-Cutting

e h t s s e Harn ower of p c i t a m pneu air-powered Malco’s d get on the n a s l o o t ! r e t s a f road

2600

RPM

4 CFM, 133 L/Min

2600 90 PSI, 6.2 Bar TR/Min

Air Powered TurboShears, Door Skin Removal and Hemming TurboXTools are work-saving innovations targeted to the restoration and collision repair pro. Replaceable blades

Long-life, dual ball bearings Air supply compatible with most existing air set-ups

7

METAL CUTTING • QUARTER PANEL HEMMING • DOOR SKIN REMOVAL • DOOR SKIN HEMMING


METAL-CUTTING AIR POWERED TURBOSHEARS

18 GAUGE AIR TOOL Beefy, wide-opening jaws easily navigate body panels, layered metal and thick plastic bumper profiles.

TSHD1A1

• Compact, lightweight, one-hand operation. • Cuts straight and to the left for tight round and square body patches. • Operates at high or low speeds for maximum control and precision.

2600

RPM

4 CFM, 133 L/Min

2600 90 PSI, 6.2 Bar TR/Min

• Lateral blade adjustment ensures optimum cutting performance for life of blades. • Easily replaceable, long-lasting blades.

16 GAUGE AIR TOOL TSA1A

Heavy-metal-cutting performance all for automotive-grade sheet steel from trunk pans to floor boards. • Helical (spiral shaped) foot for easy left, right or straight cuts. • Outstanding accessibility and control at high to low speeds. • Five-position, adjustable head cuts through profiles and into corners. • Adjustable blade-insert clearance ensures optimum cutting performance for life of blades. • Long-life, 4-sided blade inserts are easily replaced without head disassembly.

5

LOCKING POSITIONS

2600

RPM

4 CFM, 133 L/Min

2600 90 PSI, 6.2 Bar TR/Min

A five position 0 to 90 degree (0, 22.5, 45, 67.5 and 90) adjustable head angle makes these TurboShears exceptionally maneuverable and accessible for cuts through profiles and into tight spaces.

8


New

METAL-CUTTING AIR POWERED TURBOSHEARS

DOUBLE-CUT AIR TOOL Use your existing Air Compressor for fast, clean shearing on both edges of the cut. • Compact head and blade length navigates 90° outside profiles. • Cuts up to 18-gauge (1.22 mm) automotive steel. • Makes clean cuts on both edges as scrap spirals out of tool path. • Cleanly disengages from cut without pulling scrap through tool head.

TSMDA1

2600

RPM

4 CFM, 133 L/Min

2600 90 PSI, 6.2 Bar TR/Min

9


DOOR SKIN AIR POWERED TURBOXTOOLS

2600

RPM

4 CFM, 133 L/Min

2600 90 PSI, 6.2 Bar

DSR1A

TR/Min

DOOR SKIN REMOVAL AIR TOOL Cut off damaged door skins cleanly with ease! No more dust, dirt or sparks and burns from time-consuming grinding. • Lateral blade adjustment ensures optimum cutting performance. • Long-lasting blades are easily replaceable. • Serrated upper blade bites onto the two layers of metal without slipping.

SPACER BAR

Narrow working head with spacer bar, cuts through rounded edge of door hem.

METAL-CUTTING & DOOR SKIN REMOVAL AIR TOOL TURBOSHEARS TOOL

WEIGHT

REPLACEMENT PARTS

TSHD1A1 Metal-Cutting 18 gauge (1.22 mm) Air Tool Turboshear

3.3 lbs (1.50 kg)

TSHDRBC (Blades)

TSA1A Metal-Cutting 26-16 gauge (0.46-1.52 mm) Air Tool Turboshear

4.5 lbs (2.04 kg)

TSA1RB (Cutter Bits)

TSMDA1 Double Cut Air Tool Turboshear

18 gauge (1.22 mm)

3.6 lbs (1.63 kg)

TSMDRBC (Blades)

DSR1A

20 gauge (0.91 mm)

4.2 lbs (1.9 kg)

DSR1RB (Blades)

Door Skin Removal Air Tool Turboshear

CAPACITY

10


DOOR SKIN AIR POWERED TURBOXTOOLS

DHT1A

DOOR SKIN HEMMING AIR TOOL

Hem edges of replacement door skins with speed, precision and limited manual tacking.

Hems door skins with speed and precision! 2600

RPM

4 CFM, 133 L/Min

2600 90 PSI, 6.2 Bar TR/Min

• Easily operated with one hand. • High impact ABS polymer anvil guides head, while pressed against outer edge and finished side of door, skin without marring or scratching. • Hemming tool head is resistant to solvents and easily cleaned of any panel adhesive.

Anvil guides head without marring or scratching finished side of door. Slightly angling lip of replacement door skin with a hammer and dolly and flattening point of entry ensures a smooth operation.

11

FOR FACTORY-LIKE FINISH!


QUARTER PANEL AIR POWERED TURBOXTOOLS

QUARTER PANEL HEMMING AIR TOOL

Use air power to bend and close wheel arc flanges of replacement quarter panels with speed, precision and limited manual tacking.

QHT1A

• One-hand operation. • Quickly hem quarter panels on late model cars with a range of wheel arc flange widths up to 3/4 inch (19.05 mm). • Anvil and hammer head may be cleaned of any adhesive residue from hemming operation using a common solvent.

2600

RPM

• Long wearing Anvil and Hammer are easily replaced on the job.

TR/Min

Bull nose face orientation: Tighten lower set screw to secure head. Use rounded bull nose face to roll over flange.

BEST NEW

COLLISION REPAIR & REFINISH PRODUCT 2014 AWARD WINNER

4 CFM, 133 L/Min

2600 90 PSI, 6.2 Bar

Flat face orientation: Tighten striking angle before tightening head. Use flat face to close and seal seam.

Hem replacement quarter panels on late model cars up to 80% faster!

DOOR SKIN HEMMING AIR TOOL TURBOSHEARS TOOL

CAPACITY

WEIGHT

REPLACEMENT PARTS

DHT1A

Door Skin Hemming 20 gauge (0.91 mm) 4.0 lbs (1.81 kg) Air Tool Turboshear

DHTRA (Anvil)

QHT1A

Quarter Panel Hemming 28-22 gauge (0.38-0.76 mm) 3.5 lbs (1.59 kg) Air Tool Turboshear

QHT1RA (Anvil) QHT1RH (Hammer)

12


DENT REMOVAL SYSTEM & METAL WORKING TOOLS

PNEUMATIC DENT REMOVAL & PUSH-TO-PAINT REPAIR Fast, air-actuated solution for controlled dent removal and push-to-paint repair. This unique rapid dent removal system offers adjustable air power to vary the speed and intensity of the pick action to quietly and effectively work out dents with minimum arm, wrist and hand strain. Use the RADiTAP™ to access dents via door and gate latch openings, through trunk and engine compartments, from wheel wells and more. RDR1

RDR2 6 mm

RDR3

RDR5 6 mm

RDR6 19 mm

MINIMUM REQUIREMENTS: 2600 SPM • 4 CFM, 133 L/Min 90 PSI, 6.2 Bar

RDR

RDR8 11 mm

RDR4 11 mm

This innovative system compliments the skills of the dent specialist and reduces costs for the repair tech!

18 x 15 mm

4 mm

RDR7 6 mm

A total of 8 pick and tip head configurations, plus 3 interchangeable 18, 36 and 48-inch (46, 91 and 122 mm) drive shaft rods allow multiple set-up combinations to achieve the best fit for the dent removal task at hand.

Adjustable air valve varies the speed and intensity of pick action to quietly work out dents.

PUNCH & FLANGE AIR TOOL

Versatile 2-in-1 design reduces metal fabrication time by half.

One tool makes both holes and flanges in 22 to 16-gauge (0.76 to 1.52 mm) automotive grade, mild steel to accommodate clean, no-bump lap welds. Use one side of the tool head to punch a clean, flat, burr-free 5/16 inch (8 mm) diameter hole. Use the other side of the tool head to form a 7/16 inch (11 mm) long, 1 inch (25.4 mm) wide and .040 inch (1 mm) deep offset flange. The head also rotates for ease of use. Every pull of the motor lever delivers a single stroke punch or flange crimp with precision control.

13

AIR REQUIREMENTS: 4 CFM, 133 L/Min – 90 PSI, 6.2 Bar

PF1 EV


METAL WORKING TOOLS

SPOT WELD CUTTER KIT

SCREW EXTRACTOR KIT

• Includes: 3/8-inch double ended cutter, five replacement cutter bits, center drill and 5/16-inch cobalt drill bit.

• Kit contains 10 pieces total, including: 5 straight-fluted, extra-bite, hardened alloy steel extractors (Sizes #1-5) and 5 matched left-handed cobalt drill bits: 5/64, 7/64, 5/32, 1/4 and 19/64 inch.

Remove spot welds in one step and save valuable time.

• Use for screw and bolt diameters of 1/4 inch (M3) to 5/8 inch (M15).

A non-walking self-centering bit lets you drill the

Individual replacement parts sold separately: SE1: #1 Extr. & 5/64-inch Cobalt Drill Bit SE2: #2 Extr. & 7/64-inch Cobalt Drill Bit SE3: #3 Extr. & 5/32-inch Cobalt Drill Bit SE4: #4 Extr. & 1/4-inch Cobalt Drill Bit SE5: #5 Extr. & 19/64-inch Cobalt Drill Bit

center pilot hole and then continue with the weld cutting process immediately with the attached cutter bit. Finish removing the weld without needing to change bits.

SEK1

The depth adjustment ensures drilling only through the top panel without

SW1

damaging the second panel below. Individual replacement parts sold separately:

SW2: 3/8 inch Spot Weld Cutter Assembly SW3: 5/16 inch Cobalt Spot Weld Drill Bit SW4: Spot Weld Replacement Kit: (3) 3/8 ich Cutter Bits and (1) Center Drill Bit

COMPLETE TORX SOCKET KIT

TXSA1

CONNEXT3™

(3 Adapters)

1/4 x 3/8 inch

• 12 socket drive torx bits.

• 3 hex drive adapters for 1/4, 3/8 and 1/2-inch square socket drives.

1/4 x 1/2 inch

TXSK1 Kit

• CONNEXT3™ ratcheting handle with 1/4-inch hex holder. • Durable polymer storage case.

Forward Reverse Locked

Ratcheting Handle

1/4 x 1/4 inch

T15

T20

T25

T27 1-1/ 2 inch

You’ll have the right sized star socket bits

on hand for removing and replacing fenders, door handles, headlamps, pickup tailgates, and other parts. The kit comes with

T30

T40

T45

T47

1-7/ 8 inch

T50

T55

T60

T70 2-1/ 4 inch

every size of star socket drive bits from T15 to T70, equipping you for almost all star socket situations. A great buy compared to typical competing kits which provide only the smaller sizes or the higher end bits. The Malco CONNECT3 reversing ratcheting handle is included. Not for use with impact drivers.

Warning: Not for use with impact drivers.

Sockets also sold individually.

14


METAL-CUTTING SNIPS

MAX 2000

®

Nothing outcuts, outmaneuvers or outlasts Max!

METAL-CUTTING SNIPS

Easy to grip for full-length cuts in 18-gauge sheet metal.

M2002 M2003

M2001

M2001 - Left Cutting 1-3/8-inch (34.9 mm) cut M2002 - Right Cutting 1-3/8-inch (34.9 mm) cut M2003 - Combination Cutting 1-11/16-inch 42.9 mm) cut M2005 - Notching & Trimming 1-1/16-inch (27.0 mm) cut M2006 - Offset, Left Cutting 1-1/4-inch (31.8 mm) cut M2007 - Offset, Right Cutting 1-1/4-inch (31.8 mm) cut

“Bulldog” M2005

“Offset” M2006

“Offset” M2007

MINI AVIATION SNIPS METAL-CUTTING SNIPS

“Left Cutting Offset” AVM6 EV

Real Performance in a compact, offset snip! • Forged-steel jaws with serrations on lower jaw provide sharply defined 3/4-inch (19 mm) cut. • Hardened steel-core handles are torsion-spring actuated. • Soft, non-slip grip contours and handle opening fit any hand size. AVM6 EV - Offset, Left Cutting 3/4-inch (19 mm) cut AVM7 EV - Offset, Right Cutting 3/4-inch (19 mm) cut

“Right Cutting Offset” AVM7 EV

ANDY SNIPS TM

METAL-CUTTING SNIPS

Andy Snips & Andy Classic Snips with high carbon steel blades & aluminum frames offer excellent maneuverability. Andy Snips are available in gripped and un-gripped, while the Andy Classics feature a snug handle opening. TM

TM

TM

TM

MULTIPLE PURPOSE SNIPS MV12 - 12-inch (31 cm) Combination Snip, 3-inch (76 mm) cut • Replacement Blades: MV12RB

Ultra sharp high-carbon steel blades cut like a knife and are easily replaceable on the job! Perfect for car bumpers and a variety of other flexible non-ferrous materials.

MV12

SHEET METAL SNIPS

(24-Gauge sheet metal capacity.) M12A - “Andy Classic” 12-inch (31 cm) Pattern Snip, 3-inch (76.2 mm) cut • Replacement Blades: M12ARB M14N - 14-inch (36 cm) Pattern Snip, 3-1/4-inch (82.6 mm) cut • Replacement Blades: M14NRB MC14N - 14-inch (36 cm) Combination Snip, 3-1/4-inch (82.6 mm) cut • Replacement Blades: MC14NRB

15

M12A

Andy Classic 12-inch (31 cm) Pattern Straight shearing, mild curve cuts and multiple layers of material.

M14N

Andy 14-inch (36 cm) PatternStraight shearing, mild curve cuts, and multiple layers of material.

MC14N

Andy 14-inch (36 cm) Combination L or R circles to 6-inch (15 cm) diameter and straight cuts.


METAL BENDING TOOLS

HAND SEAMERS

WITH ERGONOMIC REDLINE GRIPS The premier choice for bending, folding, flattening and straightening sheet metal edges.

Featuring RedLine Handle Technology!

S2R

3-1/4-inch (83 mm) blade width

S3R

3-1/4-inch (83 mm) blade width

S6R

METAL SEAMERS Precise vee-notched depth graduations on jaws are in 1/4-inch (6.4 mm) increments.

6-inch (152 mm) blade width

S9R

9-inch (152 mm) blade width

S2R - 3-1/4-inch W x 1-1/4-inch. D (83 x 31.8 mm) Forged Steel Jaws S3R - 3-1/4-inch W x 1-1/4-inch D (83 x 31.8 mm) Forged Steel Offset Jaws S6R - 6-inch W x 1-1/4-inch D (152 x 31.8 mm) Forged Steel Jaws S9R - 9-inch W x 2-inch D (229 x 50.8 mm) Die Cast Zinc Jaws

STRAIGHT OR OFFSET GRIPPED SEAMER TONGS

S10

Generous throat depths and openings handle a broad range of bending and seaming applications.

S11

CAST STEEL SEAMERS & TONGS 3-1/2-inch W x 1-1/2-inch D (89 x 38 mm) straight, offset & vinyl-gripped combinations. S10 - Straight Jaws SG10 - Straight, Gripped Jaws S11 - Offset Jaws SG11- Straight, Gripped Jaws

SG10

“Non Marring”

SG11 16


TOOLBOX ESSENTIALS

STEP DRILLS 1/4-inch 5/16-inch 3/8-inch 7/16-inch 1/2-inch 9/16-inch

UB1

UB11

UB20

HAND RIVETER Features long and short (power) stroke. 2IN1 - 3/32 - 3/16-inch (2.4 - 4.8 mm) steel capacity, 3/32 - 5/32-inch (2.4 - 4.0 mm) stainless steel capacity

5/8-inch 11/16-inch 3/4-inch

High Speed Step Drills for soft or thin materials.

4 styles to choose from.

UB3

UB1 - 13 holes (1/8 - 1/2-inch) in 1/32-inch increments UB11 - 11 holes (1/4 - 7/8-inch) in 1/16-inch increments UB20 - 8 holes (9/16 - 1-inch) in 1/16-inch increments UB3 - 9 holes (1/4 - 3/4-inch) in 1/16-inch increments

FIN STRAIGHTENING TOOLS Radiator Repair

Easy one-hand pulling power fits all popular size rivets.

2IN1

DURABLE NYLON TOOL BAG

18 Pockets

Durable nylon bag with non-slip rubber grips. 10 exterior pockets. 8 interior pockets. TB1 - L-17 x W-8 x H-8 inch (43 x 20 x 20 cm)

FST

TB1

FST2

Nylon construction with one-piece adjustable combs. Non-marring. FST - 8, 10, 12, 14 fins per inch (25 mm) FST2 -Â 16, 18, 20, 22 fins per inch (25 mm)

DEADBLOW HAMMER Steel shot inside head absorbs impact to prevent recoil. DB1

One-piece construction of weather-resistant urethane compound ensures long service life. DB1 - One-piece urethane, non-marring, non-sparking, non-recoiling, 17 oz. (482g), 3-1/2-inch (89 mm) head length.

17

SCRATCH AWLS High Carbon alloy steel, shatterproof handles, resharpenable. A0 - 1/8-inch (3.2 mm) diameter A00 - 1/8-inch (3.2 mm) diameter A1 - 7/32-inch (5.6 mm) diameter A2 - 1/4-inch (6.4 mm) diameter A3 - 5/16-inch (7.9 mm) diameter

A1

Scribe lines and pierce holes in plastic, leather and light gauge metal.

A2 A3

A0 A00


TOOLBOX ESSENTIALS

ONE-INCH NOTCHER

CG18

CG10 N2R

The N2R Notcher punches a big 1-inch (25.4 mm) deep “V” notch in common 24- to 30-inch (0.71-0.41 mm) gauge galvanized sheet metal quickly and easily.

CG12 CG20

CAULKING GUNS

N2R - Throat Depth 1-inch (25.4 mm)

Easy loading and lightweight for smooth, clean operation. CG10 - 1/10 gal. cart. cap., 2-inch (51 mm) cart. dia. CG12 - Puncture Wire, 1/10 gal. cart. cap., 2-inch (51 mm) cart. dia. CG18 - Heavy-duty, Rotating barrel, 1/10 gal. cart. cap., 2-inch (51 mm) cart. dia. CG20 - Heavy-duty, Puncture wire, 1/10 gal. cart. cap., 2-inch (51 mm) cart. dia.

RATCHETING CONNEXT3™ HANDLE Forward or Reverse ratchet driving, as well as a locked driving position. Meets torque capacity standards (including ANSI) comparable to a 1/2-inch solid shaft driver! A quick-connect holder accepts most 1/4-inch hex shank driver or insert bits.

Rated #1. Zip-in® screws are the best selling sheet metal screws worldwide. U.S. Patent No. D524,638

LOOK FOR THE DOTS!®

POCKET SIZED SHEET METAL SCRIBE

Scribe common place trim lines on galvanized sheet metal. Ten pre-set scribing depths from 1/8 to 1 inch (3 to 25 mm). A40 - 1/8, 3/16, 1/4, 5/16, 3/8,1/2, 5/8, 3/4, 7/8, 1 inch (3.2, 4.8, 6.4, 9.5, 12.7, 15.9, 19.1, 22.2, 25.4 mm)

A40

SELF-PIERCING SHEET METAL SCREWS The standard by which all others are judged. A unique thread design and quality controlled manufacture spell the Zip-in® difference.

PAINTED SHEET METAL / DRILL IN SCREWS Drill-In screws, Type A, Single Thread (Shown in Bags)

ADJUSTABLE SHEET METAL SCRIBE Measure, mark and scribe trim lines on sheet metal in one easy operation. Adjustable from 1/4 to 12-1/2 inch (6.4 to 318 mm) depths. Rotate the scriber extension and knob end to end for depths larger than 6-1/2 inch (165 mm). A60 - Min-Max adjustments 1/4 to 12-1/2-inch (6.4 to 318 mm) A60

HW8x3/4ZT - Zip-in® Tub, Head Zinc Plated, Size 1/4-inch, Quantity 1000 HW6x3/8ZRBT - Painted Drill-in Screws Tub, Color Royal Brown (RB), Size 1/4-inch, Qty. 1000 HW6x3/8ZWT - Painted Drill-in Screws Tub, Color White (W), Size 1/4-inch, Quantity 1000

TR18 TR42

SHEET METAL DOUBLE ENDER DRILL BITS

TRP

DE18 Two points for twice the life, twice the convenience. DE18 - Polished Drill Bit - 1/8-inch (3.175 mm) Qty. 12 DE18B - Polished Drill Bit Bulk Pack - 1/8-inch (3.175 mm) Qty. 144

EXPANDABLE TRAMMEL POINTS DE18B

SLIP-ON SPRING TUBE BENDERS TB1026 - 3/8-inch (9.5 mm) O.D. capacity TB1028 - 1/2-inch (12.7 mm) O.D. capacity TB1020 - 5/8-inch (15.9 mm) O.D. capacity TB1022 - 3/4-inch (19.1 mm) O.D. capacity TB102K - Kit: 5-piece set including Tube Benders above plus 1/4-inch (6.4 mm) O.D. size

Bend tubing including brake lines and more without collapsing walls.

The TR42 expands to a big 42-inch (107 cm) radius (84-inch diameter). The compact TR18 expands to 18-inch (46 cm) and stores in most tool boxes. TR18 - 18-inch (46 cm) • TR42 - 42-inch (107 cm) • TRP - Replacement Points

TUBE SLICER Cuts hose up to 1-inch (25.4 mm) I.D. TC400 - Cutting applications include ABS, PVC, and rubber tubing and fabric-reinforced hose.

TC400

18


MALCO PRODUCTS, INC. Annandale, Minnesota U.S.A. www.malcotools.com © 2016

20

SL16352B

Malco Autobody Catalog  
Read more
Read more
Similar to
Popular now
Just for you