Magnetic drill model CTYP-100 Operator's Manual: For your own safety, before using the equipment, check voltage and see if all accessories and parts are well fastened to the machine. If you have any question whatsoever, contact Merax's technical assistance service before using the Merax CTYP-100 Magnetic Drill. Motor Max. cutting ø Max. Depth of Cut Rotation Size (mm) Magnet Force Weight
1800 W 100 mm 60 mm 82/180/245/535 RPM 710 x 490 x 165 32000 N 29 kg.
Safety Instructions • Connected ground wiring. Merax CTYP-100 must not be used without ground wiring. Do not change/damage cord or plug. • Avoid direct contact between your body and surfaces to eliminate the risk of electric shock • Do not expose the Merax CTYP-100 Drill or its tools to the rain or damp places to avoid the risk of electric shock. • Never carry your Merax CTYP-100 by the power supply cord. This can damage your machine and volt electric shock.
• When you need to use the Merax CTYP-100 Drill in open places, use an extension cord appropriate for open areas, avoiding the risk of electric shock. • Always use safety equipment – safety goggles, mask, safety shoes, and ear protectors. • Do not overload the machine. Use the adequate tool for type of drilling to be conducted ,guaranteeing the good quality of the work and the safety in the operation. • Do not change tools with the drilling machine turned on. Always turn machine off and unplug it for your own safety. Use: • This machine is specially designed for perforation of light steel. It cannot be used for other purposes under any circumstance. Equipment must not be modified. Assembly of the Merax CTYP-100 Drill and tools change: Before using your magnetic drill, you need to install the tools. Quando utilizar as Fresas Anulares, o Pino Piloto deve ser o 1º item a ser inserido na CTYP-100. The pilot pin must be the first item to be installed in the CTYP-100. After that, slide the annular cutter into an adapter. After your hear a "click" sound, it means that it is locked. Use a hex wrench text to fasten it, making sure it is securely locked Warning: make sure the lock is in the annular cutter and not on the shaft. To remove the cutting tool (annular cutter), perform backwards procedure. 3
Check if the magnet base is on and accordingly fixed, pushing the Pilot Pin. If the rotation is too weak or too strong, adjust the rotation of the drill. When the Merax CTYP-100 Magnetic Drill is not in use, keep it clean and remove all accessories from it. Safety in my magnetic base: The energization of the Merax CTYP-100 Magnetic Drill depends on the thickness of the material you are working with. A thickness of 12 mm is excellent to guarantee a safe operation. Keep all work place clean, since magnet base is damaged by chips and dirt, both as to its energization and lifecycle of the base. Before drilling, make sure the magnet base is firmly attached to the workpiece. If necessary, use the current for a safer fixation. Adjusting and Regulating the Drill: Periodically, inspect your Merax CTYP-100 Magnetic Drill. . Check lubrication, tools sharpening, carbon brush, cleaning and all accessories of the machine. Use wrenches to unfasten nuts. Always remember to fasten them securely, and whenever the rack-and-pinion move, check its fastening to guarantee quality and safety during work.
Maintenance: Always keep tools and power supply cord in clean areas. In case of electric or mechanic failure turn drill off and unplug from power source. Excessive sparking can indicate the presence of dirt in the motor or worn carbon brushes. Periodically, check the need for the carbon brushes set replacement. Always replace carbon brushes when they reach 6 mm. Brushes cannot be this limit to avoid damage to the machine Also, check lubrication. WARRANTY: MERAX Magnet Base Drilling Machines have a 6-month guarantee in Brazil after the date of issue of invoice or delivery of the product to the final consumer. This warranty applies to manufacturing, materials, parts and workmanship defects, when adequately proven. This warranty does not apply to damages provoked by inadequate transportation, accidents of any type, misuse, electrical installation oscillations, use of wrong voltage, bad quality of compressed air, the removal or alteration of the series number of the machine, and the non-compliance with the instructions herein contained This warranty does not apply to any component that deteriorates under normal use. Use only original spare parts and always contact a Merax Authorized Assistance. Check list in our website: www.merax.com.br
Parts Listing N째 2 3 4 5 6 12 19 25 27 28 33 34 35 41 42 49 51 54 56 58 60 63 64 65 71 72 74 75 83 84 85 86 91 92 94 77 78 100 101 102 103 104 105
Code C10002 C10003 C10003 C10003 C10006 C10012 C10019 C10025 C10027 C10028 C10033 C10034 C10035 C10041 C10041 C10049 C10051 C10054 C10056 C10058 C10060 C10063 C10063 C10063 C10071 C10072 C10074 C10075 C10083 C10084 C10085 C10086 C10091 C10092 C10094 C10100 C10100 C10100 C10100 C10100 C10100 C10100 C10100
Description POWER SWITCH CTYP-100 COMPLETE FUSE HOLDER CTYP100 COMPLETE FUSE HOLDER CTYP100 COMPLETE FUSE HOLDER CTYP100 MOTOR REVERSION SWITCH CTYP-100 LEVER CTYP100 SPIRAL CONDUIT CTYP100 CONTROL PLATE CTYP100 ON/OFF SWITCH MAGNET BASE CTYP100 MAGNET BASE CTYP100 INNER STRIPPER CTYP100 INNER STRIPPER CTYP100 INNER STRIPPER CTYP100 OIL RESERVOIR CTYP100 OIL RESERVOIR CTYP100 BEARING CTYP100 RACK-AND-PINION GEAR CTYP100 CROWN GEAR CTYP-100 PINION GEAR I CTYP100 SPEED CHANGE DEVICE CTYP100 MAIN GEAR CTYP100 SPEED SWITCH CTYP100 SPEED SWITCH CTYP100 SPEED SWITCH CTYP100 MORSE CONE TAPPER CTYP100 SPEED CHANGE DEVICE CTYP100 CROWN GEAR CTYP-100 PINION GEAR II CTYP100 BRUSH HOLDER CAP CTYP100 BRUSH CTYP100 BRUSH HOLDER CTYP100 MOTOR CAPACITOR CTYP100 ELECTRIC COIL CTYP100 COIL PROTECTOR CTYP100 INDUNCTION MOTOR CTYP100 CHUCK, ANNULAR CUTTER CTYP100 CHUCK, ANNULAR CUTTER CTYP100 CHUCK, ANNULAR CUTTER CTYP100 CHUCK, ANNULAR CUTTER CTYP100 CHUCK, ANNULAR CUTTERCTYP100 MANDRIL BROCA ANULAR DA CTYP100 CHUCK, ANNULAR CUTTER CTYP100 CHUCK, ANNULAR CUTTER CTYP100