Technical data, dimensions and weights are given as an indication only. CLAAS reserve the right to make changes in design and specifications at any time without previous notice and rejects all responsibility in ca se of errors.
NOTE: Front, rear, right and left refer to direction of travel.
Cutterbar
Cutting widths
Height adjustment
Cutting height range
Clearance height under cutterbar skid
Reel drive
Reel height adjustment
Feeder house
Cutterbar clutch
Threshing Equipment
Stone trap
Concave
Disawning
Threshing drum
hydraulic
To be sure, always compare settings and filling' capacities with specifications stated in the appropriate Operator's Manual for the machine concerned.
Threshing mechanism clutch
from 360 mm (14 1/4 in) below ground level to 1300 mm (51 1/4 in) above ground level. with floatation springs in use 950 mm (37 112 in) with floatation springs blocked 1100 mm (43 1/2 in)
belt-operated variable speed drive
hydraulic
chain-type feed rake
hydraulic standard equipment
adjustable from operator's platform
rear of concave separately adjustable (2nd lever)
width 1580 mm (621/4 in), 12 bars
disawning plates underneath the concave, two and three disawning plates can be engaged separately
width 1580 mm (62 1/4 in)
diameter 450 mm (17 3/4 in)
six rasp bars, seven drum discs speed infinitely variable from 650 to 1500 1/min (rpm)
Optional:
a) step pulley drive - 750, 1000, 1200, 1500 1Imin (rpm)
b) slow-speed threshing drum drive kit (chain drive) from 290 to 680 1/min (rpm)
hydraulic
Straw Walkers
Type
No. of walker racks
No. of walker crankshafts
Speed of walker crankshafts
No. of tine crankshafts
No. of tines per crankshaft
Walker area
Separating area
Cleaning
Type
Wind volume control
Total cleaning area
Grain tank
Capacity
Unloading tube
Engines
Cubic capacity
Max. speed l/min (rpm)
Idle speed 1/min (rpm)
kW (DIN H.P.)
Cooling
Fuel tank capacity
step type walkers and intensive separation system (crankshaft with tines)
220_ 5 1/min (rpm)
7.00 m 2 (10 850 sq in)
7.95m 2 (12322sqin)
forced air cleaning fan by infinitely variable fan speed additional fan shutters (optional)
5.10 m 2 (7905 sq in)
6500 litres (178.75 U. K. bushels; 184.6 U .S. bushels) hydraulically operated position control
Ground drive
Transmission
Ground speeds in kilometers per hour
Forward travel
Reverse travel
Ground speeds in miles per hour
Forward travel
Reverse travel
Traction Wheel Drive
Steering
hydrostatic, controlled by lever on operator's platform
three gear ranges in either forward or reverse
1. and 2. gear range for field operations
3. gear range for road travel
on 23.1-26 R1 / 18.4-34 R1 tyres
1. from 0 to 6.1 km/h (from 0 to 7.7 km/h)
2. from 0 to 8.9 km/h (from 0 to 11.1 km/h)
3. from 0 to 20.0 km/h (from 0 to 25.5 km/h)
1. from 0 to 4.6 km/h (from 0 to 5.8 km/h)
2. from 0 to 6.6 km/h (from 0 to 8.8 km/h)
3. from 0 to 15.3 km/h (from 0 to 19.0 km/h) on 23.1-26 R1/ 18.4-34 R 1 tyres
1. from 0 to 3.8 mph (from 0 to 4.8 mph)
2. from 0 to 5.5 mph (from 0 to 6.9 mph)
3. from 0 to 12.4 mph (from 0 to 15.8 mph)
1. from 0 to 2.9 mph (from 0 to 3.6 mph)
2. from 0 to 4.1 mph (from 0 to 5.5 mph)
3. from 0 to 9.5 mph (from 0 to 11.8 mph)
Figures in brackets are only applicable for certain countries. In countries with a speed limit of 20 km/h (12.4 mph) for self-propelled machinery of husbandry, the hydrostatic drive system incorporates a device that limits the ground speed accordingly.
via final drive gears in oil bath
hydrostatic
Weights
Combine equipped with 18.4-34 Rl and 14.5/75-20 tyres, empty fuel tank and six cylinder engine: Determine the total weight of the machine by adding the weight of the equipment used on the combine to the weight of the basic machine.
Basic machine (without cutterbar)
With cutterbar and spring tine reel
3.90 m (13 ft)
4.50 m (15 ft)
5.10 m (17 ft)
5.70 m (19 ft)
With bat-type reel
6.60 m (22 ft)
7.50 m (25 ft)
Two cpl. divider assemblies
With straw chopper
With four-row maize picker head
With five-row maize picker head
With six-row maize picker head
With maize head stalkchopper
With wheel weights (one set)
With liquid ballast (magnesium chloride solution) filled into tyres
With extra weights in compliance with road regulations (not for all countries) Combine
Ib)
104 kg ( 2291b)
254 kg ( 560 Ib)
300 kg ( 661 Ib)
over Tyres
Diameter, conforming to DIN 70020 Specifications
To
SETTINGS AND CAPACITIES
Hydraulic Oil Pressures
Lift hydraulic system pressure relief valve
Hydrostatic steering system pressure relief valve
Hydrostatic ground drive:
(LINDE hydrostatic pump BPV 100 S)
Charge pressure
Operati ng pressu re
(SAUER hydrostatic pump SPV 23)
Charge pressure
Operating pressure
Oil Capacities
Transmission gearbox
Final drive gearboxes
Lift hydraulic system
LINDE hydrostatic ground drive system
SAUER hydrostatic ground drive system
Engines
Slip clutches
Reel
Main table auger
Upper feed rake shaft
Returns elevator
180 bar (2610 psi)
90+ 5 bar (1305+ 72 . 5 psi)
16 bar ( 232 psi) 420 bar (6091 psi)
14 bar ( 203 psi) 420 bar (6091 psi)
5 litres (4.4 Imp. qt; 5.28 U.S. qt) SAE 90
(M I L-L-21 05 B) API-G L-5-90
Hypoid Transmission Oil
4 litres each (3.5 Imp. qt; 4.2 U.S. qt) SAE 90
(M I L-L-21 05 B) API-G L-5-90
Hypoid Transmission Oil
approx.7 litres (6.2 Imp.qt; 7.4 U.S. qt)
Hydraulic Oil, H-LP Oils conforming to (DI N 51524) ISO-VG 68 Specifications
approx. 8 litres (7 Imp. qt; 8.5 U.S. qt)
Hydraulic Oil, H-LP Oils conforming to (DIN 51524) ISO-VG 68 Specifications
approx. 27 litres (23.76 Imp. qt; 28.5 U.S. qt)
Hydraulic Oil, H-LP Oils conforming to (DI N 51524) ISO-VG 68 Specifications
consult engine instruction book and combine operator's manual
200 Nm (145 ft Ib)
200 Nm (145 ft Ib)
220 Nm (159 ft Ib)
adjust ratchet clutch so that no play exists
Shear Bolt
Grain tank unloading system
Knife Register
Reel
Basic setting
Main table auger
Basic setting
Concave
Control (initial) setting
M 10 x 45 DIN 931-8.8
the center of the knife sections should line up with the center of the cutterbar fingers at each end of the knife stroke
reel drive shaft placed vertically over the knife. The tines should be adjusted to vertical position.
approx. 15 mm (19/32 in) clearance between auger flights and bottom of cutterbar
concave entrance: 13 mm (1/2 in)
concave exit:
concave main adjusting lever: concave rear adjusting lever:
clearance measured at third concave bar
3 mm (1/8 in)
clearance measured at third last concave bar
locked in 3rd hole of quadrant
locked in 1st hole of quadrant (e = narrow)
Brakes Steering
Foot brake
Hand brake
brake must grip when the pedal is depressed through one third of its total travel brake should be effective with the hand-l-e·locked in the first three to four teeth in the segment
with the steering cylinder piston rod fully extended, the adjustable stop bolts must be contacting the steering arms
Technical data, dimensions and weights are given as an indication only. CLAAS reserve the right to make changes in design and specifications at any time without previous notice and rejects all responsibility in case of errors.
NOTE: Front, rear, right and left refer to direction of travel.
Cutterbar
Cutting widths
Height adjustment
Cutting height range
Clearance height under
cutterbar skid
Reel drive
Reel height adjustment
Feeder house
Cutterbar clutch
Threshing Equipment
Stone trap
Concave
Disawning
Threshing drum
Threshing mechanism clutch
To be sure, always compare settings and filling capacities with specifications stated in the appropriate Operator's Manual for the machine concerned.
hydraulic from 360 mm (14 114 in) below ground level to 1300 mm (51 114 in) above ground level with floatation springs in use 925 mm (36 112 in) with floatation springs blocked 1075 mm (42 114 in)
belt-operated variable speed drive
hydraulic
chain-type feed rake
belt-operated
standard equipment
adjustable from operator's platform
rear of concave separately adjustable (2nd lever)
width 1320 mm (52 in), 12 bar
disawning plates underneath the concave, two and three disawning plates can be engaged separately
width 1320 mm (52 in)
diameter 450 mm (17 3/4 in)
six rasp bars, six drum discs
speed infinitely variable from 650 to 1500 1Imin (rpm)
Optional:
a) step pulley drive 800, 1000, 1200, 1500 1Imin (rpm)
a1) additional speed 650 1/min (rpm)
b) slow speed threshing drum drive kit, 3-speed chain drive: 300, 430 and 550 1/min (rpm)
belt-operated
Straw Walkers
Type
No. of walker racks
No. of walker crankshafts
Speed of walker crankshafts
No. of tine crankshafts
No. of tines per crankshaft
Walker area
Separating area
Cleaning
Type
Wind volume control
Total cleaning area
Grain tank
Capacity
Unloading tube
Engine
Cubic capacity
Max. speed 1Imin (rpm)
Idle speed 1Imin (rpm)
kW (DIN H.P.)
Cooling
Fuel tank capacity
Battery
Ground Drive
a) Mechanical Clutch
T ransm ission
Speed range
step type walkers and intensive separation system (crankshaft with tines) five two
220_ 5 1/min (rpm) two five
5.80 m 2 (8990 sq in)
6.60 m 2 (10230 sq in)
forced air cleaning fan by infinitely variable fan speed additional fan shutters (optional)
4.25 m 2 (6588 sq in)
5200 litres (143 Imp. bushels, 147.7 U.S. bushels) hydraulically operated position control
variable ground speed, hydraulically controlled dry single disc clutch three forward, one reverse gear on 23.1-26 R1 tyres
Hydrostatic T ransm ission
Ground speeds in kilometers per hour
Forward travel
Reverse travel
Ground speeds in miles per hour
Forward travel
Reverse travel
Traction Wheel Drive
Steering
Brakes
controlled by lever on operator's platform
three gear ranges in either forward or reverse
1. and 2. gear range for field operation
3. gear range for road travel on 23.1-26 R1 tyres
1. from 0 to 5.4 km/h (from 0 to· 6.8 km/h)
2. from 0 to 9.9 km/h (from 0 to 12.6 km/h)
3. from 0 to 19.9 km/h (from 0 to 25.3 km/h)
1. from 0 to 4.0 km/h (from 0 to 4.9 km/h)
2. from 0 to 7.4 km/h (from 0 to 8.9 km/h)
3. from 0 to 15.0 km/h (from 0 to 18.0 km/h) on 23.1-26 R1
1. from 0 to 3.4 mph (from 0 to 4.2 mph)
2. from 0 to 6.2 mph (from 0 to 7.8 mph)
3. from 0 to 12.4 mph (from 0 to 15.7 mph)
1. from 0 to 2.5 mph (from 0 to 3.0 mph)
2. from 0 to 4.6 mph (from 0 to 5.5 mph)
3. from 0 to 11.2 mph (from 0 to 11.2 mph)
Figures in brackets are only applicable for certain countries. In countries with a speed limit of 20 km/h (12.4 mph) for self-propelled machinery of husbandry, the hydrostatic drive system incorporates a device that limits the ground speed accordingly.
via final drive gears in oil bath
hydrostatic
Where ground conditions allow maximum tyre pressure, the maximum tyre pressure should be maintained in order to obtain the longest possible service life of the tyre.
Torque Settings of Wheel
and Wheel Bolts Front wheels wheel nuts with thrust piece H 22
74361-10 = 520 Nm (376 ft Ib) Rear wheels wheel bolts M 18 x 1.5 = 325 Nm (235 ft Ib)
Weights
Combine equipped with 23.1-26 R1 and 12.5/80-18
15 tyres, empty fuel tank and six cylinder engine: Determine the total weight of the machine·by adding the weight of the equipment used on the combine to the weight of the basic machine.
Basic machine (without cutterbar)
With cutterbar and spring tine reel
3.60 m (12 ft)
3.90 m (13 ft)
4.50 m (15 ft)
5.10 m (17 ft)
5.70 m (19 ft)
Two cpl. divider assemblies
With straw chopper
With cab and ventilating system
With four-row maize picker head
With five-row maize picker head
With six-row maize picker head
With maize head stalk chopper
With wheel weights (one set)
With liquid ballast (magnesium chloride solution) filled into tyres
With extra weights in compliance with road regulations (not for all cou ntries)
Combine Dimensions
Ib)
add 104 kg ( 229 Ib)
add 210 kg ( 4631b)
add 300 kg ( 661 Ib)
Diameter, conforming to DIN 70020
HEIGHT H LENGTH L
Ta top of grain tank
When grain tank lid is open
To top of cab
To bottom edge of gran tank
Without dividers
With hoop dividers
With long dividers
With short dividers
With maize picker head
With straw hood back panel adjusted to rearward position
With straw spreader
SETTINGS AND CAPACITIES
Hydraulic Oil Pressures
Lift hydraulic system pressure relief valve
Hydrostatic steering system pressure relief valve
Hydrostatic ground drive:
(LINDE hydrostatic pump BPV 70 S)
Charge pressure
Operating pressure
(SAUER hydrostatic pump SPV 22)
Charge pressure
Operati ng pressu re
Oil capacities
Transmission gearbox
Final drive gearboxes
Lift hydraulic system
LI ND E hydrostatic ground drive system
SAUER hydrostatic ground drive system
Engines
Slip clutches
Reel
Main table auger
Upper feed rake shaft
Returns elevator
180 bar (2610 psi)
90+ 5 bar (1305+ 72 . 5 psi)
16 bar ( 232 psi) 420 bar (6091 psi)
14 bar ( 203 psi) 420 bar (6091 psi)
•6 litres (5.3 Imp. qt; 6.3 U.S. qt) SAE 90 (M I L-L-21 05) API-G L-4-90
Transmission Oil
3 litres each (2.6 Imp. qt; 3.2 U.S. qt) SAE 90 (MIL-L-2105) API-GL-4-90
Transmission Oil
approx.6 litres (5.3 Imp. qt, 6.3 U.S. qt)
Hydraulic Oil, H-LP Oils conforming to (DIN 51524) ISO-VG 68 Specifications
approx. 8 litres (7 Imp. qt; 8.5 U.S. qt)
Hydraulic Oil, H-LP Oils conforming to (DIN 51524) ISO-VG 68 Specifications
approx. 27 litres (23.76 Imp. qt; 28.5 U.S. qt)
Hydraulic Oil, H-LP Oils conforming to (DIN 51524) ISO-VG 68 Specifications
consult engine instruction book and combine operator's manual
200 Nm (145 ft Ib)
200 Nm (145 ft Ib)
220 Nm (159 ft Ib)
adjust ratchet clutch so that no play exists
Shear Bolt
Grain tank unloading system
Knife Register
Reel
Basic setting
Main table auger
Basic setting
Concave
Control (initial) setting
M 10 x 45 DIN 931-8.8
the center of the knife sections should line up with the center of the cutterbar fingers at each end of the knife stroke
reel drive shaft placed vertically over the knife. The tines should be adjusted to vertical position.
approx. 15 mm (19/32 in) clearance between auger flights and bottom of cutterbar
concave entrance: 13 mm (1/2 in)
concave exit:
concave main adjusting lever: concave rear adjusting lever:
clearance measured at third concave bar
3 mm (1/8 in)
clearance measured at third last concave bar
locked in 3rd hole of quadrant
locked in 1st hole of quadrant (e = narrow)
Brakes Steering 1.16
Foot brake
Hand brake
brake must grip when the pedal is depressed through one third of its total travel brake should be effective with the handle locked in the first three to four teeth in the segment.
with the steering cylinder piston rod fully extended, the adjustable stop bolts must be contacting the steering arms
TechniCaI data, dimensions and weights are given as an indication only. CLAAS reserve the right to make changes in design and specifications at any time without previous notice and ejects all responsibilit'! in case of errors.
NOTE: Front, rear, right and left refer to direction of travel.
Cutterbar
Cutting widths
Height adjustment
Cutting height range
Clearance height under
cutterbar skid
Reel drive
Reel height adjustment
Feeder house
Cutterbar clutch
Threshing Equipment
Stone trap
Concave
Disawning
Threshing drum
Threshing mechanism clutch
To be sure, always compare settings and filling capacities with specifications stated in the appropriate Operator's Manual for the machine concerned.
hydraulic from 360 mm (14 1/4 in) below ground level to 1300 mm (51 114 in) above ground level with floatation springs in use 900 mm (35 1/2 in) with floatation springs blocked 1040 mm (41 in)
belt-operated variable speed drive
hydraulic
chain-type feed rake
belt-operated
standard equipment
adjustable from operator's platform
rear of concave separately adjustable (2nd lever)
width 1320 mm (52 in), 12 bar
disawning plates underneath the concave, two and three disawning plates can be engaged separately
width 1320 mm (52 in)
diameter 450 mm (17 3/4 in)
six rasp bars, six drum discs speed infinitely variable from 650 to 1500 1/min (rpm)
Optional:
a) step pulley drive 800, 1000,1200, 1500 1Imin (rpm)
a1) additional speed 650 1/min (rpm)
b) slow speed threshing drum drive kit, 3-speed chain drive: 300, 430 and 550 1/min (rpm)
belt-operated
Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL.NOWAITING
NOTE:
If there is no response to click on the link above, please download the PDF document first and then clickonit.
Straw Walkers
Type
No. of walker racks
No. of walker crankshafts
Speed of walker crankshafts
No. of tine crankshafts
No. of tines per crankshafts
Walker area
Separating area
Cleaning
Type
Wind volume control
Total cleaning area Grain tank
step typ walkers and intensive separation system (crankshaft with tines)
Ground Drive
a) Mechanical Clutch Transmission Speed range
Traction Wheel Drive
Steering
Brakes
Foot brake
Hand brake
variable ground speed, hydraulically controlled dry single disc clutch
three forward, one reverse gear on, 18.4-30 R1 /.23.1-26 R1 tyres
1. Gear 1.6 to 4.0 km/h (0.9 to
2.
via final drive gears in oil bath
hydrostatic
hydraulic, designed to work independently when the pedal lock is removed
mechanical, independent of foot brake
Weights
Combine equipped with 18.4-30 R1 and 12.5/80-18
Impl. tyres, empty fuel tank, six cylinder engine. Determine the total weight of the machine by adding the weight of the equipment used on the combine to the weight of th"e basic machine.
Basic machine (without cutterbar)
With long lip cutterbar and spring tine reel
3.60 m (12 ft)
3.90 m (13 ft)
4.50 m (15 ft)
5.10m(17ft)
5.70 m (19 ft)
Two cpl. divider assemblies
With straw chopper
With cab and ventilating system
With four-row maize picker head
With five-row maize picker head
With six-row maize picker head
With maize head stalk chopper
With wheel vveights (one set)
With liquid ballast (magnesium chloride solution) filled into 12.5/80-18 rear tyres
With extra weights in compliance with road regulations (not for all countries) Combine Dimensions