Page 1

GeoLok

®  

 

Opera,on  Training Locking  &  Latching  

Start


Locking  &  Latching  

! Before  you   start  

Before  a4emp7ng  to   install  your  GeoLok   on  a  shipping   container,  the  Lock   must  be  “Unlocked”   and  “Unlatched”. Next


Locking  &  Latching  

!

Verify  an  “Unlatched”  condi7on  by   squeezing  the  Latch  Release Latch  Release  

Before  you   start  

Carry  Handle  

Next


Locking  &  Latching  

! Before  you   start  

 

Squeezing  the  Latch  Release  against  the   Carry  Handle  opens  the  Latch.     Next


Locking  &  Latching   Square  Drive  

! Before  you   start  

Verify  an   “Unlocked”   condi7on  by   pushing  in  the   Square  Drive   Socket    

If  the  Square   Drive  will  not   push  in,  the  Lock   is  in  a  “Locked”   condi7on;   a  valid  Unlock   code  is  needed   before   proceeding.  

Next


Locking  &  Latching  

! Before  you  start  

Status  LED  

If  the  GeoLok  is  Unlocked  and  Unlatched  with  no  tension   on  the  hook  then  the  “Lock”,  “Latch”,  and  “Status”    LEDs   will  be  blinking  in  unison.

Unlatched,  Unlocked,  Tension  Low  

Next


Locking  &  Latching  

! Your  GeoLok  is  ready  to    install   on  the  Container    

Next


Locking  &  Latching  

! Installing   your   GeoLok  

Open  the  Latch  by  squeezing  the  Latch  Release,  and  then   posi7on  the  GeoLok  on  the  container  doors.     While  s7ll  holding  the  Latch  open,  allow  the  Latch   mechanism  to  se4le  on  the  right  door  bar.  

Next


Locking  &  Latching  

! Installing   your   GeoLok  

Be  sure  that  the  Latch  is  fully  closed  by  verifying  that  the   Latch  Release  has  returned  to  its  normal  posi7on  before   leRng  go  of  the  GeoLok.    The  Lock  may  se4le  slightly  toward  the  bo4om  of  the   container,  but  it  should  stay  mounted.   Next


Locking  &  Latching  

! Installing   your   GeoLok  

To  install  and  lock  successfully,  the  hook  must  extend  past   the  Locking  Bar  on  the  leT  door.  

Next


Locking  &  Latching  

! Installing  your   GeoLok  

Using  the  Four  Bu4on  Key  Pad  on  the  top  of  the  Lock,   enter  the  8  digit  “Latch”  Code.  

Entering  Latch  Code  

Next


Locking  &  Latching  

! Installing  your   GeoLok  

Busy  LED  

While  you  are  entering  the  Latch  Code,  the  “Busy”  LED     will  light.    

Entering  Latch  Code  

Next


Locking  &  Latching  

! Installing  your   GeoLok  

Busy  LED  

When  the  “Latch”  motor  is  running,  the  Busy  LED  will  blink   rapidly.  Any  bu4on  pushes  entered  while  the  Busy  LED  is   blinking  will  be  ignored.  

Latching  

Next


Locking  &  Latching  

Status  LED  

! Installing  your   GeoLok  

ATer  the  GeoLok  is  Latched,  the  “Lock”  and  “Status”  LEDs   will  s7ll  be  in  unison,  but  the  “Latch”  LED  will  be  flashing   out  of  sync  with  the  others.  

Latched,  Unlocked,  Tension  Low  

Next


Locking  &  Latching  

!

Your  GeoLok  is  installed   (Latched)  on  the  Container  and   ready  to  Lock  

Next


Locking  &  Latching  

! Locking    your  GeoLok  

A  3/8”  “Speed  Wrench”  is  included  with  your  GeoLok,  but   any  standard  3/8”  square  drive  tool  will  work.

Tightening  the  Hook  

Next


Locking  &  Latching  

! Status  LED  

Locking    your  GeoLok  

Push  the  wrench  into  the  Square  Drive  Socket,  forcing  the   Square  Drive  to  engage  the  internal  locking  mechanism.     The  Status  LED  will  flash  when  the  wrench  is  engaged  with   the  Drive.

Tightening  the  Hook  

Next


Locking  &  Latching  

! Locking    your  GeoLok  

While  pushing  in  firmly  on  the  wrench,  turn  the  wrench   “clock-­‐wise”  to  7ghten  the  Locking  Hook,  making  sure  that   the  Locking  Hook  engages  the  Locking  Bar  on  the  leT  door

Tightening  the  Hook  

Next


Locking  &  Latching  

! Locking    your  GeoLok  

Con7nue  to  7ghten  un7l  the  clutch  releases  and  the  Square   Drive  Socket  slips.  

Latched,  Unlocked,  Tension  Ok  

Next


Locking  &  Latching  

Status  LED  

! Locking    your  GeoLok  

If  the  Locking  Hook  is  properly  tensioned,  the  “Latch”  and   “Status”  LEDs  will  now  be  flashing  in  unison.  The  “Lock”   LED  will  be  out  of  sync  with  the  other  two.

Latched,  Unlocked,  Tension  Ok  

Next


Locking  &  Latching  

! Locking    your  GeoLok  

Using  the  Four  Bu4on  Key  Pad  on  the  top  of  the  Lock,  enter   the  8  digit  “Lock”  Code

Entering  Lock  Code  

Next


Locking  &  Latching  

!

Busy  LED  

Locking    your  GeoLok  

While  you  are  entering  the  Lock  Code,  the  “Busy”  LED  will   light.  

Entering  Lock  Code  

Next


Locking  &  Latching  

! Locking    your  GeoLok  

Busy  LED  

When  the  “Lock”  motor  is  running,  the  Busy  LED  will  blink   rapidly.  Any  bu4on  pushes  entered  while  the  Busy  LED  is   blinking  will  be  ignored.

Locking

Next


Locking  &  Latching  

! Locking    your  GeoLok   Verify  the  Locked  condi7on  by  pushing  in  on  the  Square   Drive  Socket.  The  Socket  should  not  go  in  if  the  unit  is   Locked Next


Locking  &  Latching  

! Status  LED  

Locking    your  GeoLok   If  the  “Lock”,  “Latch”,  and  “Status”  LEDs  are   now  all  blinking  in  unison,  you  GeoLok  Is   Locked,  Latched,  and  properly  tensioned  on   the  container.

Latched,  Unlocked,  Tension  Ok  


GeoLok Training  

GeoLok Operation Training

Advertisement
Read more
Read more
Similar to
Popular now
Just for you