Page 1

PRODUCT CATALOG

The partner you were looking for

V18.01


PRODUCTS 1. WHO WE ARE ................................................................................................................... 1 2. MERAKI LED MODULES.................................................................................................. 3 ECO 282 - LINEAL CC(280X24MM)........................................................................................... 4 ECO 702 - LINEAL CC (70X24MM)............................................................................................ 9 ECO 282 - FOODY LINEAL CC (280X24MM)............................................................................. 13 ECO 702 - FOODY LINEAL CC (70X24MM)............................................................................... 18 ECO 286 - LINEAL CC (280X55,24MM)..................................................................................... 23 ECO 250X20 - LINEAL CV 12V (250X20MM)............................................................................. 28 ECO 282 IL SOLE - LINEAL CC ( 280X24MM)........................................................................... 33 600 - 300 - 70X20 - LINEAL CC 24V (70-600X20MM)................................................................ 38 TUNABLE WHITE 282- LINEAL CC(280X24 MM)....................................................................... 43 ECO BACKLIGHT 282-140-LINEAL CC (280X24 MM)............................................................... 47 MEDIUM FLUX 282 - LINEAL CC (280X24MM).......................................................................... 53 HIGH FLUX 282 - LINEAL CC(282X24MM)................................................................................ 57 HIGH FLUX 284 - LINEAR CC (280X40MM).............................................................................. 61 LINEAL CV MF - 3012 24V (310X12MM).................................................................................... 66 LINEAL CV MF - 1512 24V (300X12MM).................................................................................... 71 ROUND 155/70 CC AND CV(D=70/155MM).............................................................................. 76 AC DIRECT 280MM 230V-LINEAL AC (280X24 MM)................................................................. 83 AC DIRECT 155/70MM 230 VAC ROUND(70-155MM)............................................................... 87 MODULE 24V RGB 120 (5000X10MM)...................................................................................... 92 MODULE 24V WHITE 60-120 (5000X10MM).............................................................................. 96 MF CC D=20MM 3W 3535 (D=20MM)....................................................................................... 100 MERAKI RGB RIGID LINEAR CV 24 V 282-702 (70-282X24MM)............................................... 104 FINGUERS CC SQUARE (145X249MM)..................................................................................... 108

3. DUNAMIC LED DRIVERS................................................................................................. 113 DUNAMIC STEP - DOWN ECO DRIVER 12-24 CVV (55X12MM)............................................... 114 AC DRIVERS - TINY 3W 350/700MA (40X27.5X56MM).............................................................. 119 AC DRIVERS - LC SERIES PF 8,4W 350/700MA_12V/24V (146,6X21X19MM)......................... 123 AC DRIVERS - LC SERIES 8,4W 350/700 MA_ 12/24V (59X41X21.2)........................................ 126 BUCK DC 24 - 48V (56,5X32X16,5MM)...................................................................................... 129


4. LENKER LED CONTROL.................................................................................................. 134 RGBW WIRELESS DRIVER (BLUETOOTH MESH) (60X20MM).................................................. 135 GESTURE SENSOR( 85.7X31.7X16MM).................................................................................... 139 DIMMERS - DIM 10A 12-24V (45X45)........................................................................................ 144 DIMMERS - DIM 30A 12-24V (134,7X110X48,2MM).................................................................. 148

5. ALTUS LED LIGHTS ENGINES........................................................................................ 155 DIGITAL RGB FIXTURE EASY BOX (DYNAMIC RGB)................................................................ 156 STEP ROW NUMBER . ............................................................................................................... 161 STEP PROFILE KAV.................................................................................................................... 165

6. ACCESORIES.................................................................................................................... 170 LINK CONNECTOR B2B MODULES.......................................................................................... 171 DOUBLE TAPE BOND 4965....................................................................................................... 173 DOUBLE TAPE BOND 7054....................................................................................................... 175 CONNECTION BOX BOXCON 12-48V / 28 OUTPUTS............................................................... 177


WHO WE ARE ... In I+D LED we are dedicated to develop and manufacture integral and smart electronic solutions in lighting, efficent LED modules, drivers, smart controls and signature. For more than 15 years we have been focusing on product development with high added value for our clients and partners. I+D LED is in harmony with the market. We are flexible and agile: two fundamental attibutes to win any project. Continous improvement and high quality standars are our fundamental pillars. We work with the most rogorous business management systems. We are active partners of OSRAM, DALI, Diia, ZHAGA, and other hightech institutions arround Europe to ensure a reliable connection to IoT products. We put effort and work hard on customers partnerships.Working with us guarantees a positive costumer experience. Meet us!

Our Headquarters is located in Paterna, Valencia city, Spain. At this location, we bring together all required sources and right professionals to deliver fast and hight quality products. Research and development play a central role in our businnes.R+D join together in our lab, offering us the capacity to manufacture all kind of light engines.

1


idea... Our Know-How and experience allows us to advise our clients, ensuring that their products are allways at technology forefront. We optimize available technological resources to reach costumer´s specifications in the corresponding legal framewrks.Our advice has its fundamental basis in our R&D results, and is applied for both standard and custom-made products.

research... With more than 15 years of groundbreaking experience in LED technology, we base our commitment to costumers in the continous search of pioneering elements. Our aim is to acquire new knowdelege for the creation of new products, with the intention to contribute considerably to the improvement of the already exixting ones.

development... Technological knowledge and development in tune with our know-how is the initial step for new products design. In the field of lighting and electronic controls we ensure proper functionality and increase lif time. At this stage functional samples are created, tested and delivered to our customers for subsequent homologation.

manufacturing... Research and development come together in the manufacture of final product. We have a large production capacity with 5 SMT-SMD-TH insertion machines, welding robots, and an internal design laboratory. Our total production is subject to periodical quality controls trought test logs, and 100% made in EU. Our commitment is to ensure effinency and optimal results in ech of our production batches. 2


MERAKI LED MODULES

Office lighting_ Meraki 300-20 34V

lED modules from MERAKI family are suitable for any lighting application: from linear low cost solution, to high-end products.This family upgrades your fromer LED generation to a higher performance level and gives you the key to be one step ahead in efficency, lumen output, cost efficency, diffused lighting and more. Color consistency and lifetime are fundamental features in the seding of MERAKI modules. In order to avoid any unwanted color consistency troubles, all LED used in the different types of Meraki modules are identical and were selected with the color criteria 2 and 3 from Mc Adams steps. Additional CCT and CRI options are possible thanks to our CUSTOM and OEM flexible policy. MERAKI LED modules provide the ideal solution to integrate brand new products with fixtures designed with former tecnology.

LINEAL

Pub_RGB Systems Dynamic

CIRCULAR

RECTANGULAR

Avalaible in 2700/2000/4000/5000K

CRI>80 and 90

Long lifetime >50.000 hrs.

SELV voltage modules

Effiiency>180 lm/W

Easy thermal management

CCT Consistency of 2 and 3 SDCM

Simple installation

Fast Push-in type connectors

Low cost and low energy consumption

Tunable white and RGB solutions

Zhaga compliant

5Years limited warranty

High Light and Electronic quality standads

PMW dimmable

Lettuce growing_horticultural light engine 3


MERAKI LED MODULES IMPROVING

TECHNOLOGY

ECO 282 - LINEAL CC(280X24MM)

New modules MERAKI ECO 282 from MERAKI LINEAL CC family are ideal for flexible fixtures that require high performance and excellent Im/$ relation. These modules are very simple to connect and to assembly to any surface. Specially indicated for the production of linear lighting, both direct and indirect. Available in 24 and 12 LED per module. The modules have two different functioning: high flux and high efficiency. Depending on its input current, heatsinks could be avoid. Modules are available in diverse CCT and SELV voltage.

lm/$

>175 lm/w

5Years

Guarantee

In compliance with: IEC 62031 / IEC 62471 / IEC 62717

APPLICATION

MERAKI ECO 282 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

PRODUCT DESCRIPTION

Available in 2700K-3000K-4000K-5000K

CRI>80

Efficiency > 175 lm/W

Colour tolerance 3 SDCM

Easy to install

Space-saving design

Life-time exceeds 50.000 hrs.

5 years guarantee

High lm/$ relation

4


MERAKI LED MODULES ECO 282 - LINEAL CC(280X24MM)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS

(*) 24 Led

Disponible en 2700-3000-4000-5000K

CRI80 típico, CRI90 bajo pedido

Funcionamiento -20ºC +45°C

EN 61471:2008 grupo 1

Tc típico 65°C

Apertura LED 120°

Peso 20 g

MOQ 44 uds

Peso caja aprox. 900 g

PWM dimmable.

125

24

24

Tensión de funcionamiento SELV

18

280

18

IMPROVING

125

1.60

4.72

125.65

(*) 12 Led

(*) Measured in mm 280 125

125

1.60

4.72

249.65

SPECIFIC TECHNICAL DATA - 24 LED MODULE CODE

CCT

QTY LED

CRI typ.

31.13.07009 31.13.07009 31.13.07009

2700K 2700K 2700K

24 24 24

>80 >80 >80

200 350 500

23,2 23,2 23,2

23,4 24,6 25,7

26,4 26,4 26,4

0,202 0,353 0,502

4,72 8,68 12,90

138,512 114,696 101,105

730,56 1.228,80 1.541,52

827.348 827.348 827.348

31.13.07010 3000 K 31.13.07010 3000 K 31.13.07010 3000 K

24 24 24

>80 >80 >80

200 350 500

23,2 23,2 23,2

23,4 24,6 25,7

26,4 26,4 26,4

0,202 0,352 0,502

4,72 8,65 12,90

156,783 137,578 120,509

741,08 1.191,31 1.554,74

830.348 830.348 830.348

31.13.07011 4000 K 31.13.07011 4000 K 31.13.07011 4000 K

24 24 24

>80 >80 >80

200 350 500

23,2 23,2 23,2

23,1 24,3 25,3

26,4 26,4 26,4

0,202 0,352 0,502

4,66 8,55 12,70

177,356 162,121 142,130

827,58 1.386,72 1.805,14

840.348 840.348 840.348

31.13.07012 31.13.07012 31.13.07012

24 24 24

>80 >80 >80

200 350 500

23,2 23,2 23,2

23,1 24,3 25,3

26,4 26,4 26,4

0,202 0,352 0,502

4,66 8,55 12,70

195,860 184,961 161,832

796,08 1.429,20 1.886,88

850.348 850.348 850.348

5000K 5000K 5000K

AVERAGE MIN. STANDARD MAX. RATED CURRENT VOLTAGE VOLTAGE VOLTAGE VOLTAGE (V) (A) (V) (V) Tc=65ºC (mA)

NOMINAL EFFICIENCIES STANDARD PHOTO (lm / W) POWER METRIC FLUX (W) CODE (Im)(*)

(**) It is required to keep Tc < 65ºC. (***) For PCB supply including high adhesion thermal tape, please add the letter “C” behind the product code. Example: 31.13.0625C.

MERAKI ECO 282 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

5


MERAKI LED MODULES IMPROVING

ECO 282 - LINEAL CC(280X24MM)

TECHNOLOGY

SPECIFIC TECHNICAL DATA - 12 LED MODULE RATED MIN. STANDARD MAX. STANDARD NOMINAL EFFICIENCIES STANDARD PHOTO METRIC FLUX CURRENT VOLTAGE VOLTAGE VOLTAGE CURRENT POWER (lm / W) CODE (Im)(*) Tc=65ºC (V) (V) (V) (A) (W) (mA)

CCT

QTY LED

CRI typ.

2700K 2700K 2700K 2700K

12 12 12 12

>80 >80 >80 >80

200 350 400 500

11,2 11,2 11,2 11,2

11,5 12,3 12,5 12,9

12,8 12,8 12,8 12,8

0,202 0,353 0,402 0,502

2,323 4,330 5,025 6,489

144.124 106,874 105,313 92,099

334,80 462,72 529,20 597,60

827.348 827.348 827.348 827.348

31.13.07010.12 3000 K 31.13.07010.12 3000 K 31.13.07010.12 3000 K 31.13.07010.12 3000K

12 12 12 12

>80 >80 >80 >80

200 350 400 500

11,2 11,2 11,2 11,2

11,5 12,3 12,5 12,9

12,8 12,8 12,8 12,8

0,202 0,352 0,402 0,502

2,323 4,330 5,025 6,489

152,389 112,805 108,704 98,682

354,00 488,40 546,24 640,32

830.348 830.348 830.348 827.348

31.13.07011.12 4000 K 31.13.07011.12 4000 K 31.13.07011.12 4000 K 31.13.07011.12 4000K

12 12 12 12

>80 >80 >80 >80

200 350 400 500

11,2 11,2 11,2 11,2

11,5 12,3 12,5 12,9

12,8 12,8 12,8 12,8

0,202 0,352 0,402 0,502

2,323 4,330 5,025 6,489

167,886 120,565 112,000 102,548

390,00 522,00 562,80 665,40

840.348 840.348 840.348 827.348

31.13.07012.12 31.13.07012.12 31.13.07012.12 31.13.07012.12

12 12 12 12

>80 >80 >80 >80

200 350 400 500

11,2 11,2 11,2 11,2

11,5 12,3 12,5 12,9

12,8 12,8 12,8 12,8

0,202 0,352 0,402 0,502

2,323 4,330 5,025 6,489

175,583 124,418 119,642 107,060

407,88 538,68 601,20 694,68

827.348 850.348 850.348 850.348

CODE

31.13.07009.12 31.13.07009.12 31.13.07009.12 31.13.07009.12

5000K 5000K 5000K 5000K

(**) It is required to keep Tc < 65ºC. (***) For PCB supply including high adhesion thermal tape, please add the letter “C” behind the product code. Example: 31.13.0625C.

DRIVER + MODULE CONNECTION EXAMPLE

Reccommendation over PCB wire connection: ≤ 0,5 mm² (flexible) / ≤ 0,75 mm² (rigid)

230 Vac 50/60 Hz

L N

+ Conector AÉREO Ref. 06.094 (Opcional)

DRIVER Vf: 49,2 V 350 mA

IN

26 mm

Ref. 06.345

OUT

+

+

-

Max.6A

249.65

MERAKI ECO 282 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

6


MERAKI LED MODULES IMPROVING

ECO 282 - LINEAL CC(280X24MM)

TECHNOLOGY

CONNECTION AND INSTALLATION EXAMPLE

2

1

For eventual attachment of the fixture (with no use of double

Place the PCB and apply pressure. Fix the screws to the

sided adhesive tape) drill a hole in the profile.

fixture base. (*) Accessory: M3 screws.

mo du l

Max. no. of PCBs: Depends on driver type Vf total PCBs ≤ Vout Driver

to ec nn r

Connect

Place the interconnection wires.

Lifetime Derating for MERAKI LINEAL MERAKI 282 ECO 110.000 100.000 90.000 Lifetime ( L80 / B50) h

3

oard to bo he b ard ot t 6.345 co es Ref. 0

80.000 70.000 60.000 50.000 40.000

500 mA (> 48.000 hs)

30.000

350 mA (> 50.000 hs)

20.000 10.000 0 20

30

40

50 60 70 Temperature Tc (°C)

MERAKI ECO 282 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

80

90

100

7


MERAKI LED MODULES IMPROVING

TECHNOLOGY

ECO 282 - LINEAL CC(280X24MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER MERAKI ECO 282 must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). Family MERAKI LED MODULES have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. MERAKI LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION MERAKI ECO 282 functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION MERAKI ECO 282 contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI ECO 282 must be perfectly placed (and/ or stick) on the lighting device, profile or base for a proper connection between modules and power source. Thermal transference between PCB and luminaire body must be at its highest, in order to ensure that fixture temperature does not exceed Tc in any case. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs. The module will be delivered with 5 pre-made holes of D=4 mm according to dimensions drawing (ZHAGA L2W2). Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress. Ideal wire for this connection type is unipolar rigid wire of 0,4-1mm², with a strip wire of 6,5-7MM. To remove wire, push orifice on the connector and pull smoothly. TEMPERATURE MERAKI ECO 282 life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=65°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%. OPTICAL CHARACTERISTICS + CCT Measurement of LED discrete points may have variations in regards on the CCT temperature here described, with a variance of 3SDCM for white and +/- 5nm for coloured LEDs. CCT shifts +/- 0,001 at 6.000 hrs. 3 SDCM are declared over the complete module. Modules viewing angle is 120°.

MERAKI ECO 282 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

8


MERAKI LED MODULES IMPROVING

TECHNOLOGY

ECO 702 - LINEAL CC (70X24MM)

New modules MERAKI ECO 702 from MERAKI LINEAL CC family are ideal for small size fixtures that require high performance and connection flexibility. These modules are very simple to connect and to assembly to any surface. Specially indicated for the production of linear lighting, both direct and indirect. The modules have two different functioning: high flux and high efficiency. Regarding input current, heatsinks could be avoided. Modules are available on diverse CCT and SELV voltage.

lm/$

>175 lm/w

5Years

Guarantee

In compliance with IEC 62031 / IEC 62471 / IEC 62717

APPLICATION

MERAKI ECO 702 -LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

PRODUCT DESCRIPTION

Available in 2700K-3000K-4000K-5000K

CRI>80

Efficiency > 175 lm/W

Colour tolerance 3 SDCM

Easy to install

Space-sav design

Life-time exceeds 50.000 hrs

5 years guarantee

High lm/$ relation

9


MERAKI LED MODULES IMPROVING

ECO 702 - LINEAL CC (70X24MM)

TECHNOLOGY DATOS TÉCNICOS

DIMENSIONES 70

SELV voltage

Available in 2700-3000-4000-5000K

Typical CRI80, CRI90 under request

Operating temperature between -20ºC and 18

+45°C •

EN 61471:2008 group 1

Standard Tc 65°C

LED viewing angle 120°

Weight 10 g

MOQ 96 units

Packaging weight (approx.) 960 g

PWM dimmable

24

53

(*) Measured in mm

4.7

1.6

35

SPECIFIC TECHNICAL DATA CODE

CCT

QTY LED

CRI typ.

RATED MIN. STANDARD MAX. AVERAGE NOMINAL EFFICIENCIES STANDARD CURRENT VOLTAGE VOLTAGE VOLTAGE CURRENT POWER (lm / W) FLUX Tc=65ºC (V) (V) (V) (A) (W) (Im)(*) (mA)

PHOTO METRIC CODE

31.13.07021 2700K 31.13.07021 2700K 31.13.07021 2700K

6 6 6

>80 >80 >80

200 350 500

5,6 5,6 5,6

5,85 6,15 6,43

6,6 6,6 6,6

0,202 0,353 0,402

1,182 2,171 2,585

154,557 141,505 135,343

182,64 307,20 349,84

827.348 827.348 827.348

31.13.07022 3000 K 31.13.07022 3000 K 31.13.07022 3000 K

6 6 6

>80 >80 >80

200 350 500

5,6 5,6 5,6

5,85 6,15 6,42

6,6 6,6 6,6

0,202 0,352 0,402

1,182 2,165 2,581

156,783 137,578 131,792

185,27 297,83 340,13

830.348 830.348 830.348

31.13.07023 4000 K 31.13.07023 4000 K 31.13.07023 4000 K

6 6 6

>80 >80 >80

200 350 500

5,6 5,6 5,6

5,77 6,07 6,32

6,6 6,6 6,6

0,202 0,352 0,402

1,166 2,137 2,541

177,510 162,255 155,836

206,90 346,68 395,92

840.348 840.348 840.348

31.13.07024 5000K 31.13.07024 5000K 31.13.07024 5000K

6 6 6

>80 >80 >80

200 350 500

5,6 5,6 5,6

5,77 6,07 6,32

6,6 6,6 6,6

0,202 0,352 0,402

1,166 2,137 2,541

182,542 167,225 160,610

212,76 357,30 408,05

850.348 850.348 850.348

(*) Tolerance range for flux measurements of 8%. (**) It is required to keep Tc<85ºC. (***) For PCB supply including high adhesion thermal tape, please add the letter “C” behind the product code. Example: 31.13.07023C.

DRIVER + MODULE CONNECTION EXAMPLE

Reccommendation over wire connections:

230 Vac 50/60 Hz

L

DRIVER Vf: 49,2 V 350 mA

IN

N

+ OUT

≤ 0,5 mm² (flexible) / ≤ 0,75 mm² (rigid)

-

Ref. 06.345 Conector AÉREO Ref. 06.345 (Opcional)

26 mm

Max.6A

41 MERAKI ECO 702 -LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

10


MERAKI LED MODULES IMPROVING

ECO 702 - LINEAL CC (70X24MM)

TECHNOLOGY

INSTALLATION AND CONNECTION EXAMPLE

2

1

Place the PCB and apply pressure. Fix the screws to the

sided tape) drill a hole in the profile.

lighting base. (*) Accesory: M3 screws

he board to bo to t ard s e 3 45 ul f. 06. e R

Max. no. of PCBs: depends on used driver:

co

ne

Vf total modules ≤ Vout driver

cto r

Conect th

Place the board to board connectors and join together with other modules. Fix the screws to the lighting base in accordance with the no. of modules. (*) Accessory: M3 screws. Lifetime Derating for MERAKI LINEAL MERAKI 702 ECO 110.000 100.000 90.000 Lifetime ( L80 / B50) h

3

em od

For eventual attachment of the fixture (with no use of double

80.000 70.000 60.000 50.000 40.000

400 mA (>48.000 hs)

30.000

350 mA (>50.000 hs)

20.000 10.000 0 20

30

40

50 60 70 Temperature Tc (°C)

MERAKI ECO 702 -LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

80

90

100

11


MERAKI LED MODULES IMPROVING

TECHNOLOGY

ECO 702 - LINEAL CC (70X24MM)

SECURITY AND INFORMATION INSTALLATION ELECTRICAL POWER MERAKI ECO 702 must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). Family MERAKI LED MODULES have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. MERAKI LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION MERAKI ECO 702 functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION MERAKI ECO 702 contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI ECO 702 must be perfectly placed (and/ or stick) on the lighting device, profile or base for a proper connection between modules and power source. Thermal transference between PCB and luminaire body must be at its highest, in order to ensure that fixture temperature does not exceed Tc in any case. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs. The module will be delivered with pre-made holes of D=3,2 mm according to dimensions drawing (ZHAGA L70W2). Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress. Ideal wire for this connection type is unipolar rigid wire of 0,4-1mm², with a strip wire of 6,5-7MM. To remove wire, push orifice on the connector and pull smoothly. TEMPERATURE MERAKI ECO 702life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=65°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%. OPTICAL CHARACTERISTICS + CCT Measurement of LED discrete points may have variations in regards on the CCT temperature here described, with a variance of 3SDCM for white and +/- 5nm for coloured LEDs. CCT shifts +/- 0,001 at 6.000 hrs. 3 SDCM are declared over the complete module. Modules viewing angle is 120°.

MERAKI ECO 702 -LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

12


MERAKI LED MODULES IMPROVING

TECHNOLOGY

ECO 282 - FOODY LINEAL CC (280X24MM)

MERAKI family introduces FOODY line, a series of LED modules

FOR FRESH FOOD!

with optimized spectrum, a suitable fit for illumination of fresh groceries as bread, fish, vegetables, red meat and marbled meat. These modules are specially indicated for direct linear or area applications. FOODY modules hold an excellent Im/$ relation and standard LED driver current. Efficiencies are determined by the chosen operating current. The modules have two different functioning: high flux and high efficiency. Depending on its input current, heatsinks could be avoided.

lm/$

>110 lm/w

5Years

Guarantee

In compliance with IEC 62031 / IEC 62471 / IEC 62717

APPLICATION

MERAKI ECO 282- FOODY LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

PRODUCT DESCRIPTION

Efficiency > 110lm/W

Easy to install

Push-In connectors

Colour tolerance - 3 SDCM over CCT

Available to illuminate meat, fish, bread and vegetables.

Compact design

SELV voltage

High lm/$ relation

5 years guarantee

13


MERAKI LED MODULES TECHNOLOGY

ECO 282 - FOODY LINEAL CC (280X24MM)

TECNICAL DATA

DIMENSIONS

SELV voltage

Available for MEAT - BREAD - FISH - VEGETABLES

CRI80-90

Operating temperature between -20ºC and +45°C

EN 61471:2008 group 1

Standard Tc 65°C

LED viewing angle 120°

Weight 20 g

MOQ 44 units

Packaging box weight (approx.) 900 gr

PWM dimmable

tcºC

125

24

280

18

IMPROVING

125

1.60

4.72

249.65

(*) Measured in mm

SPECIFIC TECHNICAL DATA MIN. STANDARD VOLTAGE VOLTAGE (V) (V)

MAX. VOLTAGE (V)

AVERAGE NOMINAL EFFICIENCIES STANDARD FLUX (lm / W) CURRENT POWER (Im)* (W) (A)

QTY LED

CRI typ.

RATED CURRENT Tc=65ºC (mA)

31.13.070201 BREAD 31.13.070201 BREAD 31.13.070201 BREAD

24 24 24

>90 >90 >90

200 350 500

23,2 23,2 23,2

23,4 23,4 23,4

25,2 25,2 25,2

0,202 0,354 0,502

4,73 8,28 11,75

107,74 97,20 103,22

509,28 805,20 1212,48

31.13.070203 31.13.070203 31.13.070203

FISH FISH FISH

24 24 24

>90 >90 >90

200 350 500

23,2 23,2 23,2

23,4 23,4 23,4

25,2 25,2 25,2

0,202 0,354 0,502

4,73 8,28 11,75

113,23 116,18 109,67

535,20 962,4 1288,32

31.13.070205 31.13.070205 31.13.070205

MEAT MEAT MEAT

24 24 24

>85 >85 >85

200 350 500

23,2 23,2 23,2

23,4 23,4 23,4

25,2 25,2 25,2

0,202 0,354 0,502

4,73 8,28 11,75

69,41 71,27 65,58

328,08 590,4 770,4

31.13.070207 MEAT M 31.13.070207 MEAT M 31.13.070207 MEAT M

24 24 24

>65 >65 >65

200 350 500

23,2 23,2 23,2

23,4 23,4 23,4

25,2 25,2 25,2

0,202 0,354 0,502

4,73 8,28 11,75

66,77 69,25 64,36

315,6 573,6 756

31.13.070209 VEGET 31.13.070209 VEGET 31.13.070209 VEGET

24 24 24

>90 >90 >90

200 350 500

23,2 23,2 23,2

23,4 23,4 23,4

25,2 25,2 25,2

0,202 0,354 0,502

4,73 8,28 11,75

89,26 97,78 90,61

421,92 810 1064,4

CODE

CCT

(*) Tolerance range for flux measurements of 8%. (**) It is required to keep Tc < 65ºC. (***) For module supply including high adhesion thermal tape, please add the letter “C” behind the product code. Example: 31.13.07023C.

MERAKI ECO 282- FOODY LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

14


MERAKI LED MODULES IMPROVING

ECO 282 - FOODY LINEAL CC (280X24MM)

TECHNOLOGY

DRIVER + MODULE CONNECTION EXAMPLE

230 Vac 50/60 Hz

L N

+

DRIVER Vf: 49,2 V 350 mA

IN

Wire reccommendation for modules connection:

OUT

≤ 0,5 mm² (flexible) / ≤ 0,75 mm² (rigid)

-

Ref. 06.345 Conector AÉREO Ref. 06.094 (Opcional)

26 mm

max.6wA

249.65

SPECTRUM POWER DISTRIBUTION 1.0

Red Meat Bread Produce Marbled Meat Fish

Normalized Power (-)

0.8

0.6

0.4

0.2

0.0 400

450

500

550

600

650

700

750

800

Wavelength(nm) 3SDCM DEFINICIÓN ELIPSE - PUNTO CENTRAL

Center Point (CX) Vegetables Red Meat Marbled Meat

(CY)

Rotation Elip.

0,421

0,372

53,2º

0,5

0,35

49,3º

0,395

0,325

53,7º

Fish

0,313

0,323

58,6º

Bread

0,4578

0,4101

53,7ºw

MERAKI ECO 282- FOODY LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

15


MERAKI LED MODULES IMPROVING

ECO 282 - FOODY LINEAL CC (280X24MM)

TECHNOLOGY

EJEMPLO DE INSTALACIÓN Y CONEXIÓN

*

2

1

For eventual attachment of the fixture (with no use of double

Place the PCB and apply pressure. Fix the screws to the

sided adhesive tape) drill a hole in the profile.

fixture base. Accessory: M3 screws. (*) ESD protection to earth connection. Max. no. of PCBs: depends on driver type Vf total PCBs ≤ Vout Driver

ne

cto r

Co n n e ct m od

3

oard to bo to b .345 ard c s on 06 e ul Ref.

Place interconnection board to board connectors.

Lifetime Derating for MERAKI LINEAL MERAKI 282 ECO 110.000 100.000 Lifetime ( L80 / B50) h

90.000 80.000 70.000 60.000 50.000 40.000

500 mA (> 48.000 hs)

30.000

350 mA (> 50.000 hs)

20.000 10.000 0 20

30

40

50 60 70 Temperature Tc (°C)

MERAKI ECO 282- FOODY LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

80

90

100

16


MERAKI LED MODULES IMPROVING

TECHNOLOGY

ECO 282 - FOODY LINEAL CC (280X24MM)

INSTALLATION AND CONNECTION INFORMATION ELECTRICAL POWER MERAKI ECO 282 FOODY must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). Family MERAKI LED MODULES have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. MERAKI LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION MERAKI ECO 282 FOODY functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION MERAKI ECO 282 FOODY contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI ECO 282 FOODY must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source. Thermal transference between PCB and luminaire body must be at its highest, in order to ensure that fixture temperature does not exceed Tc in any case. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs. The module will be delivered with pre-made holes of D=3,2 mm according to dimensions drawing (ZHAGA L70W2). Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress. Ideal wire for this connection type is unipolar rigid wire of 0,4-1mm², with a strip wire of 6,5-7MM. To remove wire, push orifice on the connector and pull smoothly. TEMPERATURE MERAKI ECO 282 FOODY life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=65°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%. OPTICAL CHARACTERISTICS + CCT Measurement of LED discrete points may have variations in regards on the CCT temperature here described, with a variance of 3SDCM for white and +/- 5nm for coloured LEDs. CCT shifts +/- 0,001 at 6.000 hrs. 3 SDCM are declared over the complete module. Modules viewing angle is 120°.

MERAKI ECO 282- FOODY LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

17


MERAKI LED MODULES IMPROVING

TECHNOLOGY

ECO 702 - FOODY LINEAL CC (70X24MM)

MERAKI family introduces FOODY line, a series of LED modules

FOR FRESH FOOD!

with optimized spectrum, a suitable fit for illumination of fresh groceries as bread, fish, vegetables, red meat and marbled meat. These modules are specially indicated for direct linear or area applications. FOODY modules hold an excellent Im/$ relation and standard LED driver current. Efficiencies are determined by the chosen operating current. The modules have two different functioning: high flux and high efficiency. Depending on its input current, heatsinks could be avoided.

lm/$

>110 lm/w

5Years

Guarantee

In compliance with IEC 62031 / IEC 62471 / IEC 62717

APPLICATION

MERAKI ECO 702 - FOODY LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

PRODUCT DESCRIPTION

Efficiency >110lm/W

Easy to install

Push-In connectors

Colour tolerance - 3 SDCM over CCT

Available to illuminate meat, fish, bread and vegetables

Compact design

SELV voltage

High lm/$ relation

5 years guarantee

18


MERAKI LED MODULES IMPROVING

ECO 702 - FOODY LINEAL CC (70X24MM)

TECHNOLOGY TECNICAL DATA

DIMENSIONS

SELV voltage

70

Available for MEAT - BREAD - FISH - VEGETABLES

53

CRI80-90

Operating temperature between -20ºC and +45°C

EN 61471:2008 group 1

Standard Tc 65°C

LED viewing angle 120°

Weight 20 g

MOQ 44 units

Packaging box weight (approx.) 900 gr

PWM Dimmable.

24

18

tc ºC

4.70

(*) Measured in mm

1.60

35

SPECIFIC TECHNICAL DATA MIN. STANDARD MAX. AVERAGE NOMINAL EFFICIENCIES STANDARD VOLTAGE VOLTAGE VOLTAGE CURRENT POWER FLUX (lm / W) (V) (V) (V) (Im)* (W) (A)

QTY LED

CRI typ.

RATED CURRENT Tc=65ºC (mA)

31.13.070202 BREAD 31.13.070202 BREAD 31.13.070202 BREAD

6 6 6

>90 >90 >90

200 350 500

5,8 5,8 5,8

31.13.070204 31.13.070204 31.13.070204

FISH FISH FISH

6 6 6

>90 >90 >90

200 350 500

5,8 5,8 5,8

31.13.070206 31.13.070206 31.13.070206

MEAT MEAT MEAT

6 6 6

>85 >85 >85

200 350 500

5,8 5,8 5,8

31.13.070208 MEAT M 31.13.070208 MEAT M 31.13.070208 MEAT M

6 6 6

>65 >65 >65

200 350 500

5,8 5,8 5,8

31.13.070210 VEGET 31.13.070210 VEGET 31.13.070210 VEGET

6 6 6

>90 >90 >90

200 350 500

5,8 5,8 5,8

CODE

CCT

6 6 6 6 6 6 6 6 6 6 6 6 6 6 6

6,4 6,4 6,4

0,202 0,354 0,502

1,212 2,124 3,012

105,05 94,77 100,64

127,32 201,3 303,12

6,4 6,4 6,4

0,202 0,354 0,502

1,212 2,124 3,012

110,40 113,28 106,93

133,8 240,6 322,08

6,4 6,4 6,4

0,202 0,354 0,502

1,212 2,124 3,012

67,67 69,49 63,94

82,02 147,6 192,6

6,4 6,4 6,4

0,202 0,354 0,502

1,212 2,124 3,012

65,10 67,51 62,75

78,9 143,4 189

6,4 6,4 6,4

0,202 0,354 0,502

1,212 2,124 3,012

87.03 95.34 88.35

105,48 202,5 266,1

(*) Tolerance range for flux measurements of 8%. (**) It is required to keep Tc < 65ºC. (***) For module supply including high adhesion thermal tape, please add the letter “C” behind the product code. Example: 31.13.07023C.

MERAKI ECO 702 - FOODY LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

19


MERAKI LED MODULES IMPROVING

ECO 702 - FOODY LINEAL CC (70X24MM)

TECHNOLOGY

DRIVER + MODULE CONNECTION EXAMPLE

230 Vac 50/60 Hz

L N

+

DRIVER Vf: 49,2 V 350 mA

IN

Wire reccommendation for modules connection:

OUT

≤ 0,5 mm² (flexible) / ≤ 0,75 mm² (rigid)

-

Ref. 06.345 Board to board connector. Ref. 06.345 (optional)

26 mm

Max.6A

41

SPECTRUM POWER DISDISTRIBUTION 1.0

Red Meat Bread Produce Marbled Meat Fish

Normalized Power (-)

0.8

0.6

0.4

0.2

0.0 400

450

500

550

600

650

700

750

800

Wavelength(nm) 3SDCM DEFINICIÓN ELIPSE - PUNTO CENTRAL

Center Point (CX) Vegetables Red Meat Marbled Meat

(CY)

Rotation Elip.

0,421

0,372

53,2º

0,5

0,35

49,3º

0,395

0,325

53,7º

Fish

0,313

0,323

58,6º

Bread

0,4578

0,4101

53,7ºw

MERAKI ECO 702 - FOODY LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

20


MERAKI LED MODULES IMPROVING

ECO 702 - FOODY LINEAL CC (70X24MM)

TECHNOLOGY

INSTALLATION AND CONNECTION INFORMATION

2

1

Place the PCB and apply pressure. Fix the screws to the

sided adhesive tape) drill a hole in the profile.

fixture base. Accessory: M3 screws. (*) ESD protection to

oard to board to b .345 co s 06 e n ul Ref.

earth connection. Max. Nno. Of modules: depends on driver type

ne

cto r

Vf total Modules ≤ Vout Driver

Place interconnection board to board connectors and join together modules, tight screws to the profile. Accessory: M3 screws. Lifetime Derating for MERAKI LINEAL MERAKI 702 ECO 110.000 100.000 90.000 Lifetime ( L80 / B50) h

3

Co n n e ct m od

For eventual attachment of the fixture (with no use of double

80.000 70.000 60.000 50.000 40.000

400 mA (>48.000 hs)

30.000

350 mA (>50.000 hs)

20.000 10.000 0 20

30

40

50 60 70 Temperature Tc (°C)

MERAKI ECO 702 - FOODY LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

80

90

100

21


MERAKI LED MODULES IMPROVING

TECHNOLOGY

ECO 702 - FOODY LINEAL CC (70X24MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER MERAKI ECO 702 FOODY must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). Family MERAKI LED MODULES have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. MERAKI LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION MERAKI ECO 702 FOODY functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage of is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION MERAKI ECO 702 FOODY contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI ECO 702 FOODY must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source. Thermal transference between PCB and luminaire body must be at its highest, in order to ensure that fixture temperature does not exceed Tc in any case. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs. The module will be delivered with pre-made holes of D=3,2 mm according to dimensions drawing (ZHAGA L70W2). Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress. Ideal wire for this connection type is unipolar rigid wire of 0,4-1mm², with a strip wire of 6,5-7MM. To remove wire, push orifice on the connector and pull smoothly TEMPERATURE MERAKI ECO 702 FOODY life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=65°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%. OPTICAL CHARACTERISTICS + CCT Measurement of LED discrete points may have variations in regards on the CCT temperature here described, with a variance of 3SDCM for white and +/- 5nm for coloured LEDs. CCT shifts +/- 0,001 at 6.000 hrs. 3 SDCM are declared over the complete module. Modules viewing angle is 120°.

MERAKI ECO 702 - FOODY LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

22


MERAKI LED MODULES IMPROVING

TECHNOLOGY

ECO 286 - LINEAL CC (280X55,24MM)

New modules MERAKI ECO 286 from MERAKI LINEAL CC family are ideal for flexible fixtures that require high performance and excellent Im/$ relation. These modules are very simple to connect and to assembly to any surface. Specially indicated for the production of linear and direct lighting, as for display on shelves, supermarket aisles and warehouses. The modules have two different functioning: high flux and high efficiency. Depending on its input current, heatsinks could be avoided. Modules are available in diverse CCT and SELV voltage. Compatible with LEDil FLORENCE lenses array.

lm/$

>150 lm/w

5Years

Guarantee

In compliance with IEC 62031 / IEC 62471 / IEC 62717

PRODUCT DESCRIPTION

APPLICATION

MERAKI ECO 286 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

Available in 2700K-3000K-4000K-5000K

CRI>80

Efficiency > 150 lm/W

Colour Tolerance 3 SDCM

Easy to install

Space-saving design

Life-time exceeds 50.000 hrs.

5 years guarantee

High lm/$ relation

Compatible with LEDiL Florence

23


MERAKI LED MODULES IMPROVING

ECO 286 - LINEAL CC (280X55,24MM)

TECHNOLOGY THECNICAL DATA

DIMENSIONS 280.42

Available in 2700-3000-4000-5000K.

Typical CRI80

Operating temperature between -20ºC +45°C

EN 62471:2008 group 1

Max. Tc 85°C

LED viewing angle 120°

Weight 20 g

116.06

34.70

31.59

30.59

40

33.68

55.24

SELV Voltage

27.64

49.20

76.60 79.40

MOQ 44 units

Packaging box weight (approx.)1Kg

PWM Dimmable.

49.22

26

F14170_FLORENCE-ZT25 / F14112_FLORENCE-Z60 / /

F14486_FLORENCE-Z30

(*) Measured in mm

/

1.60

F13853_FLORENCE-Z90

5.95

(*) Compatible with the following LEDIL Florence models:

F15069_FLORENCE-0 / F15244_FLORENCE_ZT25-S. SPECIFIC TECHNICAL DATA CCT

QTY LED

31.13.07017 31.13.07017 31.13.07017

2700K 2700K 2700K

33 33 33

>80 >80 >80

200 350 500

30,8 30,8 30,8

31,1 33,2 34,6

34,1 34,1 34,1

0,202 0,353 0,502

6,28 11,62 17,36

130,798 105,077 91,196

821,70 1.221,00 1.584,00

827.348 827.348 827.348

31.13.07018 3000 K 31.13.07018 3000 K 31.13.07018 3000 K

33 33 33

>80 >80 >80

200 350 500

30,8 30,8 30,8

31,5 33 34,4

34,1 34,1 34,1

0,202 0,352 0,502

6,36 11,55 17,26

137,435 118,571 100,325

874,50 1.369,50 1.732,50

830.348 830.348 830.348

31.13.07019 4000 K 31.13.07019 4000 K 31.13.07019 4000 K

33 33 33

>80 >80 >80

200 350 500

30,8 30,8 30,8

31,8 33,3 34,9

34,1 34,1 34,1

0,202 0,352 0,502

6,42 11,65 17,52

144,358 127,696 116,971

927,30 1.488,30 2.049,30

840.348 840.348 840.348

31.13.07020 31.13.07020 31.13.07020

33 33 33

>80 >80 >80

200 350 500

30,8 30,8 30,8

31,1 33,2 34,6

34,1 34,1 34,1

0,202 0,352 0,502

6,28 11,62 17,36

154,962 134,897 121,975

973,50 1.567,50 2.118,60

850.348 850.348 850.348

5000K 5000K 5000K

CRI RATED typ. CURRENT Tc=65ºC (mA)

MIN. STANDARD MAX VOLTAGE VOLTAGE VOLTAGE (V) (V) (V)

AVERAGE NOMINAL EFFICIENCIES STANDARD PHOTO METRIC FLUX CURRENT POWER (lm / W) CODE (Im)(*) (A) (W)

CODE

(**) It is required to keep Tc < 85ºC

DRIVER + MODULE CONNECTION EXAMPLE

85 - 230 Vac 50/60 Hz

L N

DRIVER V=20-100V 350 /500mA

IN

Reccommendation over PCB wire connection: ≤ 0,5 mm² (flexible) / ≤ 0,75 mm² (rigid)

+ OUT

-

(*) When choosing driver, consider max. and min. voltage here indicated.

30,8 V

30,8 V

30,8 V

In: 350mA / Vf: 91,5 V MERAKI ECO 286 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

24


MERAKI LED MODULES IMPROVING

ECO 286 - LINEAL CC (280X55,24MM)

TECHNOLOGY

INSTALLATION Y CONNETION EXAMPLE

2

1

For eventual attachment of the fixture (with no use of

Place the PCB and apply pressure. Fix the screws to the

double-sided tape) drill a hole in the profile

lighting base. (*) Accessory: M3 screws.

ec

- of the mo du and les + t

Max. No. of PCBs: Depends on driver type Vf total PCBs ≤ Vout Driver

Co

nn

3 a.

r retorno rra e C er ow p l t rica ect urren l e c r t o f tan ut Inp cons

+

Co

3 b. n

c ne

tm

odules + and

Reccommendation over PCB wire connection: ≤ 0,5 mm² (Flexible) / ≤ 0,75 mm² (Rigido)

-

-

+ MERAKI ECO 286 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

Place interconnection rigid wire

25


MERAKI LED MODULES IMPROVING

ECO 286 - LINEAL CC (280X55,24MM)

TECHNOLOGY

Lifetime Derating for MERAKI LINEAL MERAKI 286 ECO

110.000 100.000 Lifetime ( L80 / B50) h

90.000 80.000 70.000 60.000 50.000 40.000

500 mA (> 48.000 hs)

30.000

350 mA (> 50.000 hs)

20.000 10.000 0 20

30

40

50 60 70 Temperature Tc (°C)

80

90

100

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER MERAKI ECO 286 must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). Family MERAKI LED MODULES have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. MERAKI LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION MERAKI ECO 286 functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION MERAKI ECO 286 is contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu.

MERAKI ECO 286 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

26


MERAKI LED MODULES IMPROVING

TECHNOLOGY

ECO 286 - LINEAL CC (280X55,24MM)

MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI ECO 286 must be perfectly placed (and/ or stick) on the lighting device, profile or base for a proper connection between modules and power source. Thermal transference between PCB and luminaire body must be at its highest, in order to ensure that fixture temperature does not exceed Tc in any case. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs. The module will be delivered with 4 pre-made holes of D=4,5 mm according to dimensions drawing (ZHAGA L2W6). Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress. Ideal wire for this connection type is unipolar rigid wire of 0,4-1mm², with a strip wire of 6,5-7MM. To remove wire, push orifice on the connector and pull smoothly. TEMPERATURE MERAKI ECO 286 life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=85°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%. OPTICAL CHARACTERISTICS + CCT Measurement of LED discrete points may have variations in regards on the CCT temperature here described, with a variance of 3SDCM for white and +/- 5nm for coloured LEDs. CCT shifts +/- 0,001 at 6.000 hrs. 3 SDCM are declared over the complete module. Modules viewing angle is 120°.

MERAKI ECO 286 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

27


MERAKI LED MODULES IMPROVING

TECHNOLOGY

ECO 250X20 - LINEAL CV 12V (250X20MM)

New MERAKI 250x20 ECO 12V from family MERAKI LINEAL CV are ideal for small size fixtures that require high performance and connection flexibility. These modules are very simple to connect and to assembly to any surface. MERAKI 250x20 ECO 12V modules are specially indicated for the production of linear lighting, both direct and indirect. It is available with 21 LED per modules. Regarding its input current, heatsinks could be avoided. Modules are available on diverse CCT and SELV voltage.

lm/$

>100 lm/w

5Years

Guarantee

In compliance with IEC 62031 / IEC 62471 / IEC 62717

APPLICATION

MERAKI ECO 250X20 - LINEAL CV 12V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

PRODUCT DESCRIPTION

Available in 2700K-3000K-4000K-5000K

CRI>80 (CRI90 available under request)

Efficiency > 100 lm/W

Colour tolerance 3 SDCM

Easy to install

Space-saving design

Life-time exceeds 50.000 hrs

5 years guarantee

High lm/$ relation

Exclusive design, no heatsink required

Extremely flat profile: 8mm

28


MERAKI LED MODULES IMPROVING

ECO 250X20 - LINEAL CV 12V (250X20MM)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS

SELV voltage

Available in 2700K/3000K/4000K/5000K

Typical CRI80 (CRI90 available under request)

Operating temperature between -30ºC and +45º C

EN 61471:2008 group 1

Standard Tc 75ºC

LED viewing angle 20º

Weight 20 g

MOQ 44 units

Possible to integrate with LOGO Custom

1.6 6.1

20

250

(*) Medidas en mm

SPECIFIC TECHNICAL DATA - 24 LED MODULE CODE

31.13.282.12.01 31.13.282.12.02 31.13.282.12.03 31.13.282.12.04

CCT

QTY LED

CRI typ.

RATED CURRENT Tc=65ºC (mA)

STANDARD VOLTAGE (V)

AVERAGE CURRENT (A)

NOMINAL POWER

LUMINOUS EFFICACY

TOTAL FLUX

PHOTO METRIC CODE

2700K 3000K 4000K 5000K

21 21 21 21

>80 >80 >80 >80

250 250 250 250

12 12 12 12

0.25 0.25 0.25 0.25

3.000 3.000 3.000 3.000

86.800 94.500 104.650 115.500

260.40 283.50 313.95 346.50

827/850.348 827/850.348 827/850.348 827/850.348

(*) For nominal current values of 350 mA pasive heatsink is required. (**) It is required to keep Tc < 65ºC. (**) For PCB supply including high adhesion thermal tape, please add the letter “C” behind the product code. Example: 31.13.07012C.

DRIVER + MODULE CONNECTION EXAMPLE

230 Vac 50/60 Hz

L

DRIVER 12 Vcc

IN

N

Recommendation over PCB wire connection:

+ OUT

≤ 0,5 mm² (flexible) / ≤ 0,75 mm² (rigid)

-

Ref. 06.345 Conector AÉREO Ref. 06.345 (Opcional)

26 mm

Max.6A

MERAKI ECO 250X20 - LINEAL CV 12V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

29


MERAKI LED MODULES IMPROVING

ECO 250X20 - LINEAL CV 12V (250X20MM)

TECHNOLOGY

INSTALLATION AND CONNECTION EXAMPLE

2

1

* Tira adhesiva a doble cara 3M

Make sure that surface where the PCB (LED strip) will be stick

Remove film from adhesive tape.

is clean and flat for proper adhesion.

* ESD protection to earth connection

3

*

It is very important to keep a clear and flat surface.

Place the LED strip on top of the desired surface and apply pressure carefully. (*) ESD protection to earth connection

MERAKI ECO 250X20 - LINEAL CV 12V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

30


MERAKI LED MODULES IMPROVING

wire to wire co s to e l nn u . 06.345 e od R e f

Max. no. of PCBs: depends on driver type Vf total PCBs ≤ Vout Driver

or ct

Conn ec tm

3

ECO 250X20 - LINEAL CV 12V (250X20MM)

TECHNOLOGY

Place the wire to wire connector for interconnection.

Lifetime Derating for MERAKI LINEAL MERAKI 110.000 100.000 Lifetime ( L80 / B50) h

90.000 80.000 70.000 60.000 50.000 40.000 250 mA (>50.000 hs)

30.000 20.000 10.000 0 20

30

40

50 60 70 Temperature Tc (°C)

MERAKI ECO 250X20 - LINEAL CV 12V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

80

90

100

31


MERAKI LED MODULES IMPROVING

TECHNOLOGY

ECO 250X20 - LINEAL CV 12V (250X20MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER MERAKI 250X20 ECO 12V must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). MERAKI 250X20 ECO 12V has polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. Family MERAKI LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION MERAKI 250X20 ECO 12V functions with SELV voltage and does not require active isolation of the component as long as maximum reference SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION MERAKI 250X20 ECO 12V contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI 250X20 ECO 12V must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source. The module will be delivered with double sided tape for installation if requested (optional). Thermal transference between PCB and luminaire body must be at its highest, in order to ensure that fixture temperature does not exceed Tc in any case. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs and electronic components. Ideal wire for this connection type is unipolar rigid wire of 0,4-1mm², with a strip wire of 4-5MM. To remove wire, push orifice on the connector (or flap) and pull smoothly. TEMPERATURE MERAKI 250X20 ECO 12V life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=75°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%. OPTICAL CHARACTERISTICS + CCT Measurement of LED discrete points may have variations in regards on the CCT temperature here described, with a variance of 3SDCM and 2SDCM for white and +/- 5nm for coloured LEDs. CCT shifts +/- 0,001 at 6.000 hrs. 3 SDCM are declared over the complete module. Modules viewing angle is 120°.

MERAKI ECO 250X20 - LINEAL CV 12V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

32


MERAKI LED MODULES IMPROVING

TECHNOLOGY

ECO 282 IL SOLE - LINEAL CC ( 280X24MM)

New MERAKI ilSOLE 282 from MERAKI LINEAL CC family are ideal for small size fixtures that require high performance and excellent Im/$ relation. These modules are very simple to connect and to assembly to any surface. Specially indicated for the production of linear lighting, both direct and indirect. It has a luminous spectrum similar to sunlight, which avoids disturbing blue spectrum picks and focuses on total satisfaction for end user. It is available with 12 or 24 LED per module. Regarding input current, heatsinks could be avoided. Modules are available on diverse CCT and SELV voltage.

lm/$

>100 lm/w

5Years

Guarantee

In compliance with IEC 62031 / IEC 62471 / IEC 62717

APPLICATION

MERAKI ECO 282 IL SOLE - LINEAL CC- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

PRODUCT DESCRIPTION

Available in 2700K-3000K-4000K-5000K

CRI>97

Improves circadian cycle

Efficiency >100 lm/W

Colour tolerance 4 SDCM

Easy to install

Space-saving design

Life-time exceeds 50.000 hrs

5 years guarantee

Exclusive design (no heatsink required)

Intended for offices and homes

33


MERAKI LED MODULES IMPROVING

ECO 282 IL SOLE - LINEAL CC ( 280X24MM)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS (*) 24 LED

SELV voltage

Available in 2700K-3000K-4000K-5000K

CRI>97

Low blue spectrum picks

Operating temperature between -30ºC and 45º C

EN 61471:2008 group 1

Standard Tc 65ºC

Viewing LED angle 120º

Weight 20 g

MOQ 88 uds

Possible to integrate with LOGO Custom

24

125

Tc

(3000K in stock, other under request)

18

280

125

1.60

4.72

125.65

(*) 12 LED

(*) Measured in mm

SPECIFIC TECHNICAL DATA CODE

CCT

QTY LED

CRI RATED MIN. STANDARD MAX. AVERAGE NOMINAL EFFICIENCIES STANDARD PHOTO typ. CURRENT VOLTAGE VOLTAGE VOLTAGE CURRENT POWER (lm / W) FLUX METRIC Tc=65ºC (V) (V) (V) (A) (W) (Im)(*) CODE (mA)

31.13.282.SUN.2K7 2700K 31.13.282.SUN.2K7 2700K 31.13.282.SUN.2K7 2700K

24 24 24

>97 >97 >97

200 350 400

23,2 23,2 23,2

23,4 23,4 23,4

26,4 26,4 26,4

0,202 0,352 0.402

4,727 8,237 9,407

63,468 71,387 75,010

300 588 705,60

827.348 827.348 827.348

31.13.282.SUN.3K 3000 K 31.13.282.SUN.3K 3000 K 31.13.282.SUN.3K 3000 K

24 24 24

>97 >97 >97

200 350 400

23,2 23,2 23,2

23,4 23,4 23,4

26,4 26,4 26,4

0,202 0,352 0.402

4,727 8,237 9,407

80,020 78,730 79,602

378,24 648,48 748,80

830.348 830.348 830.348

31.13.282.SUN.4K 4000 K 31.13.282.SUN.4K 4000 K 31.13.282.SUN.4K 4000 K

24 24 24

>95 >95 >95

200 350 400

23,2 23,2 23,2

23,4 23,4 23,4

26,4 26,4 26,4

0,202 0,352 0.402

4,727 8,237 9,407

90,632 86,859 84,781

428,40 715,44 797,52

840.348 840.348 840.348

31.13.282.SUN.5K 5000K 31.13.282.SUN.5K 5000K 31.13.282.SUN.5K 5000K

24 24 24

>95 >95 >95

200 350 400

23,2 23,2 23,2

23,4 23,4 23,4

26,4 26,4 26,4

0,202 0,352 0.402

4,727 8,237 9,407

102,158 91,783 92,997

482,88 756 874,80

850.348 850.348 850.348

(**) It is required to keep Tc < 65ºC. (***) For PCB supply including high adhesion thermal tape, please add the letter “C” behind the product code. Example: 31.13.282.SUN.5KC

STANDARD LED Vs. ilSOLE LED SPECTRUM COMPARISON

Standard LED spectrum (blue pick)

MERAKI ECO 282 IL SOLE - LINEAL CC- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

Il SOLE LED spectrum (well-balanced)

34


MERAKI LED MODULES IMPROVING

ECO 282 IL SOLE - LINEAL CC ( 280X24MM)

TECHNOLOGY

¿WHY IS THIS TYPE OF LUMINOUS SPECTRUM OUTSTANDING?

Real image of retina cells: It can be distinguished that blue colour cells (Cone-S) are in lower quantity compared to other retina cells. Human retina cells RED Cone-L

GREEN Cone-M

BLUE Cone-S ip RGC

ipRGC responds to blue light by sending a signal to the brain, which ceases with melatonin production.

Blue light normal spectrum alters human circadian cycle, releasing high quantity of picks at this wave length. These picks are received by the eye, which sends signals to the brain to cease melatonin production. Melatonin deficiency has a direct negative effect on humor, sleep, and in general health status. New ilSOLE spectrum contributes to the human eye to behave naturally, as it does with sunlight.

DRIVER + MODULE CONNECTION EXAMPLE

230 Vac 50/60 Hz

L

DRIVER Vf: 49,2 V 350 mA

IN

N

Recommendation over PCB wire connection:

+ OUT

≤ 0,5 mm² (flexible) / ≤ 0,75 mm² (rigid)

-

Ref. 06.345 Wire to wire connector Ref. 06.094 (optional)

26 mm

Max.6A

249.65

MERAKI ECO 282 IL SOLE - LINEAL CC- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

35


MERAKI LED MODULES IMPROVING

ECO 282 IL SOLE - LINEAL CC ( 280X24MM)

TECHNOLOGY

INSTALLATION AND CONNECTION EXAMPLE

2

1

Place the PCB and apply pressure. Fix the screws to the

double sided adhesive tape) drill a hole in the profile.

fixture base. (*) Accessory: M3 screws.

wire to wir s to .345 e con e l 0 u ne f. 6 od R e

or ct

Max. no.º of PCBs: Depends on driver type Vf total PCBs ≤ Vout Driver

Place interconnection wires.

Lifetime Derating for MERAKI LINEAL MERAKI 282 110.000 100.000 90.000 Lifetime ( L80 / B50) h

3

Conn ec tm

For eventual attachment of the fixture (with no use of

80.000 70.000 60.000 50.000 40.000

400mA (>48.000 hs) 350mA (>50.000 hs)

30.000 20.000 10.000 0 20

30

40

50 60 70 Temperature Tc (°C)

MERAKI ECO 282 IL SOLE - LINEAL CC- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

80

90

100

36


MERAKI LED MODULES IMPROVING

TECHNOLOGY

ECO 282 IL SOLE - LINEAL CC ( 280X24MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER MERAKI 282 ILSOLE must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). Family MERAKI have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. MERAKI 282 ILSOLE has integrated protection against reverse polarity errors. MERAKI LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. Please, verify driver’s min. and max. Vn values specified in this data sheet. ISOLATION MERAKI 282 ILSOLE functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION MERAKI 282 ILSOLE contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu.. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI 282 ILSOLE must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source, respecting its nominal values. Thermal transference between PCB and luminaire body must be at its highest, in order to ensure that fixture temperature does not exceed Tc in any case. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs and electronic components. The module will be delivered with 5 pre-made holes of D=4 mm, according to dimensions drawing (ZHAGA L2W2). Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress. Ideal wire for this connection type is unipolar rigid wire of 0,4-1mm², with a strip wire of 6,5-7MM. To remove wire, push orifice on the connector and pull smoothly. TEMPERATURE MERAKI 282 ILSOLE life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=65°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%. OPTICAL CHARACTERISTICS + CCT Measurement of LED discrete points may have variations in regards on the CCT temperature here described, with a variance of 3SDCM for white and +/- 5nm for coloured LEDs. CCT shifts +/- 0,001 at 6.000 hrs. 3 SDCM are declared over the complete module. Modules viewing angle is 120°. Spectrum graph and data are sourced from LED Sunlike and LED Manuacters. MERAKI ECO 282 IL SOLE - LINEAL CC- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

37


MERAKI LED MODULES IMPROVING

TECHNOLOGY

600 - 300 - 70X20 - LINEAL CC 24V (70-600X20MM)

Within MERAKI LED MODULES family, we find MERAKI 600-300-70 / 20 24 V linear modules, ideal for small size fixtures that require high performance and connection flexibility. These modules are very simple to connect and to assembly to any surface, i.e. aluminum, wood or metal. Specially indicated for use in shelves, window display, and similar in combination with our DOKO profile. The modules have two different functioning: medium flux that require no additional heatsinks, and high flux that does require additional heatsinks. Modules are available on diverse CCT (CRI80 and CRI90) and in SELV voltage.

lm/$

>125 lm/w

5Years

Guarantee

In compliance with IEC 62031 / IEC 62471 / IEC 62717

APPLICATION

MERAKI 600 - 300 - 70 / 20 24V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

PRODUCT DESCRIPTION

Available in 2700K-3000K-4000K-5000K

CRI>80 (CRI 90 available under request)

Efficiency > 125lm/W

Colour tolerance 3 SDCM

Space-saving design

Easy to install

Life-time exceeds 50.000 hrs.

Voltage 24Vcc

5 years guarantee

High lm/$ relation

Available in 3 lengths 600 mm - 300 mm -70 mm

38


MERAKI LED MODULES IMPROVING

600 - 300 - 70X20 - LINEAL CC 24V (70-600X20MM)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS

Available in 2700-3000-4000-5000K.

Typicak CRI80, CRI90 available under request.

Operating temperature between -30ºC and45º C

EN 61471:2008 group 1

Standard Tc 65°C

LED viewing angle 120°

600-20 - Weight 24 g

39.65

296.80

MOQ 60 pieces packaging box weight 1500 g •

5

1.60

SELV voltage

20

66.80

300-20 - Weight 12 g

20

MOQ 120 pieces packaging box weight 1100 g 70-20 - Weight 8 g

269.70

MOQ 120 pieces packaging box weight 960 g

(*) Measured in mm

5

Possibility to integrate LOGO Custom 1.60

20

596.80

5

1.60

569.70

SPECIFIC TECHNICAL DATA CODE

70 - 20 24 VCC 31.13.7020.24.2 31.13.7020.24.3 31.13.7020.24.4 31.13.7020.24.5

CCT

QTY LED

CRI typ.

RATED CURRENT Tc=65ºC (mA)

2700K 3000K 4000K 5000K

7 7 7 7

>80 >80 >80 >80

70 70 70 70

24 24 24 24

0,07 0,07 0,07 0,07

1,680 1,680 1,680 1,680

91,458 103,333 112,917 124,958

153,65 173,60 189,70 209,93

827.348 830.348 840.348 850.348

2700K 3000K 4000K 5000K

28 28 28 28

>80 >80 >80 >80

280 280 280 280

24 24 24 24

0,27 0,27 0,27 0,27

6,480 6,480 6,480 6,480

94,846 107,160 114,722 129,586

614,60 694,40 743,40 839,72

827.348 830.348 840.348 850.348

2700K 3000K 4000K 5000K

56 56 56 56

>80 >80 >80 >80

560 560 560 560

24 24 24 24

0,54 0,54 0,54 0,54

12,960 12,960 12,960 12,960

94,846 107,160 114,722 129,586

1229,20 1388,80 1486,80 1679,44

827.348 830.348 840.348 850.348

SATANDARD AVERAGE VOLTAGE CURRENT (V) (A)

NOMINAL EFFICIENCIES STANDARD POWER (lm / W) FLUX (W) (Im)

PHOTO METRIC CODE

300 - 20 24 VCC 31.13.30020.24.2 31.13.30020.24.3 31.13.30020.24.4 31.13.30020.24.5 600 - 20 24 VCC 31.13.60020.24.2 31.13.60020.24.3 31.13.60020.24.4 31.13.60020.24.5

(*) It is required to keep Tc < 65ºC. (**) For PCB supply including high adhesion thermal tape, please add the letter “C” behind the product code. Example: 31.13.0625C.

MERAKI 600 - 300 - 70 / 20 24V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

39


MERAKI LED MODULES IMPROVING

600 - 300 - 70X20 - LINEAL CC 24V (70-600X20MM)

TECHNOLOGY

DRIVER + MODULE CONNECTION EXAMPLE

Reccommendation over PCB wire connection: 230 Vac 50/60 Hz

L N

+

+

-

Board to board connector Ref. 06.094 (Optional)

26 mm

-

DRIVER 24 Vcc

IN

Ref. 06.345

OUT

≤ 0,5 mm² (flexible) / ≤ 0,75 mm² (rigid)

+

+

+

-

-

Max.6A

INSTALLATION AND CONNECTION EXAMPLE

1

OVER PROFILE TRAIL

Introduce and slide the PCB inside the fixture profile by it trail.

2

WITH DOUBLE SIDED TAPE

In other case, use a specific double sided tape, and stick it on the back side of the PCB. Remove top film as indicated in the above image and attach the fixture to the designated surface.

MERAKI 600 - 300 - 70 / 20 24V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

40


MERAKI LED MODULES IMPROVING

Max. no. of PCBs: depends on driver type Pn PCBs ≤ Pn Driver

r

C o n n ec tm od

ire to bo ard the w to .345 co s 6 e 0 u l e f. R

to ec nn

3

600 - 300 - 70X20 - LINEAL CC 24V (70-600X20MM)

TECHNOLOGY

Place the wire to board connectors to interconnect the PCBs. You can create several fixture lengths, by using the different lengths available.

Lifetime Derating for MERAKI LINEAL MERAKI 600-300-70/20 ECO

110.000 100.000 Lifetime ( L80 / B50) h

90.000 80.000 70.000 60.000 50.000 40.000

100 mA (> 48.000 hs)

30.000

LED current

20.000 10.000 0 20

30

40

50 60 70 Temperature Tc (°C)

MERAKI 600 - 300 - 70 / 20 24V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

80

90

100

41


MERAKI LED MODULES IMPROVING

TECHNOLOGY

600 - 300 - 70X20 - LINEAL CC 24V (70-600X20MM)

INSTALLATION AND SECURITY INFORMATION ELECTRICAL POWER MERAKI 600-20 / 300-20 / 70-20 24V must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). Family MERAKI LED MODULES have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. MERAKI 600-20 / 300-20 / 70-20 24V has integrated protection against reverse polarity errors. MERAKI LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. Please, verify driver’s min. and max. Vn values specified in this data sheet. ISOLATION MERAKI 600-20 / 300-20 / 70-20 24V functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage of 50V is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION MERAKI 600-20 / 300-20 / 70-20 24V contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI 600-20 / 300-20 / 70-20 24V must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source. Thermal transference between PCB and luminaire body must be at its highest, in order to ensure that fixture temperature does not exceed Tc in any case. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs. Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress. Ideal wire for this connection type is unipolar rigid wire of 0,4-1mm², with a strip wire of 6,5-7MM. To remove wire, push orifice on the connector and pull smoothly. TEMPERATURE MERAKI 600-20 / 300-20 / 70-20 24V life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=65°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%. OPTICAL CHARACTERISTICS + CCT Measurement of LED discrete points may have variations in regards on the CCT temperature here described, with a variance of 3SDCM for white and +/- 5nm for coloured LEDs. CCT shifts +/- 0,001 at 6.000 hrs. 3 SDCM are declared over the complete module. Modules viewing angle is 120°.

MERAKI 600 - 300 - 70 / 20 24V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

42


MERAKI LED MODULES IMPROVING

TECHNOLOGY

TUNABLE WHITE 282- LINEAL CC(280X24 MM)

MERAKI family introduces new LED dynamic modules in white. Ideal for small size fixtures that seek dynamic colour changes solutions and require high performance and excellent Im/$ relation. MERAKI TUNABLE WHITE design is based on Circadian rhythm, searching for an appropriate influence over biological cycles. These modules are very simple to connect and to assembly to any surface. They are specially indicated for the production of linear lighting, both direct and indirect with changes in CCT. The modules have two different functioning: high flux and high efficiency. Regarding input current, heatsinks could be avoided. Modules are available on diverse CCT and SELV voltage.

lm/$

>150 lm/w

5Years

Guarantee

In compliance with IEC 62031 / IEC 62471 / IEC 62717

APPLICATION

MERAKI TUNABLE WHITE 282 - LINEAL CC- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

PRODUCT DESCRPTION

Efficiency > 150lm/W

Available in the range of 2700K - 5000K

CRI>80 (CRI90 available under request)

Easy installation

With Push-In connectors

CCT Tolerance -3 SDCM

Ideal for homes and offices

SELV voltage

5 years guarantee

43


MERAKI LED MODULES TECHNOLOGY

TUNABLE WHITE 282- LINEAL CC(280X24 MM)

TECHNICAL DATA

DIMENSIONS

SELV voltage

Available from 2700K to 5000K

Typical CRI80

Operating temperature between -20ºC and +45°C

EN 61471:2008 group 1

Standard Tc 65°C

LED viewing angle 120°

Weight 20 g

MOQ 88 units

Packaging box weight (approx.) 900 g

PWM dimmable

280

18

125 24

IMPROVING

1.60 5

125 206.6 250

(*) Measured in mm

SPECIFIC TECHNICAL DATA CODE

CCT

QTY LED

CRI typ.

MIN. STANDARD MAX. AVERAGE NOMINAL EFFICIENCIES STANDARD PHOTO RATED (lm / W) FLUX METRIC CURRENT VOLTAGE VOLTAGE VOLTAGE CURRENT POWER (Im)* (V) (V) (V) (A) (W) CODE Tc=65ºC (mA)

31.13.282.TW 31.13.282.TW

2700K 5000K

24 24

>90 >90

200 200

16,2 16,2

18,1 18,1

19,2 19,2

0,202 0,202

3,656 4,660

141,787 129,785

518,40 827/850.348 604,80 827/850.348

31.13.282.TW 31.13.282.TW

2700K 5000K

24 24

>90 >90

350 350

16,2 16,2

18,1 18,1

19,2 19,2

0,35 0,35

6,335 6,335

132,976 155,138

842,40 827/850.348 982,80 827/850.348

(*) Tolerance range for flux measurements of 8%. (**) It is required to keep Tc < 65ºC. (***) For PCB supply including high adhesion thermal tape, please add the letter “C” behind the product code. Example: 31.13.07023C.

DRIVER + MODULE CONNECTION EXAMPLE DALI PROTOCOL CONTROL

DALI BUS POWER

+

+ - DALI Dali Driver FFXXX Warm White 230 Vac

DALI MASTER

+ -

(*)Use two different directions to control tunable white LED module.

+ - DALI Dali Driver FFXXX Cool White 230 Vac

MERAKI TUNABLE WHITE 282 - LINEAL CC- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

+ -

44


MERAKI LED MODULES IMPROVING

TECHNOLOGY

TUNABLE WHITE 282- LINEAL CC(280X24 MM)

INSTALLATION AND CONNECTION EXAMPLE

*

2

1

For eventual attachment of the fixture (with no use of double

Place the PCB and apply pressure. Fix the screws

sided adhesive tape) drill a hole in the profile.

to the fixture base. Accessory: M3 screws. (*) ESD protection to earth connection.

oard to board to b co s 6.345 e n ul Ref. 0

Max. no. of PCBs: Depends on driver type Vf total PCBs ≤ Vout Driver

ne

cto r

Co n n e ct m od

3

Place interconnection connectors (board to board connectors).

Lifetime Derating for MERAKI LINEAL MERAKI 282 ECO 110.000 100.000 Lifetime ( L80 / B50) h

90.000 80.000 70.000 60.000 50.000 40.000 350 mA (> 50.000 hs)

30.000 20.000 10.000 0 20

30

40

50 60 70 Temperature Tc (°C)

MERAKI TUNABLE WHITE 282 - LINEAL CC- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

80

90

100

45


MERAKI LED MODULES IMPROVING

TECHNOLOGY

TUNABLE WHITE 282- LINEAL CC(280X24 MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER MERAKI TUNABLE WHITE 282 must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). Family MERAKI have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. MERAKI TUNABLE WHITE 282 has integrated protection against reverse polarity errors. MERAKI LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. Please, verify driver’s min. and max. Vn values specified in this data sheet. ISOLATION MERAKI TUNABLE WHITE 282 functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION MERAKI TUNABLE WHITE 282 contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI TUNABLE WHITE 282 must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source, respecting its nominal values. MERAKI TUNABLE WHITE 282 modules are designed to be incorporated inside small size light fixtures. Always avoid mechanical stress, compression stress or superficial voltage stress over the electronic components of the PCB. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs and electronic components. The module is delivered no pre-made holes. Ideal wire for this connection type is multipolar flexible wire of 0,2-0,75mm². TEMPERATURE MERAKI TUNABLE WHITE 282 life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=80°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%.

MERAKI TUNABLE WHITE 282 - LINEAL CC- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

46


MERAKI LED MODULES IMPROVING

TECHNOLOGY

ECO BACKLIGHT 282-140-LINEAL CC (280X24 MM)

New MERAKI ECO BACKLIGHT 282-140 are ideal to complete fixture designs that seek homogeneity and short distance from the module to the circuit breaker. The modules provide an alternative to former technologies for signage. They are intended to backlight and at nominal power they do not need heatsinks. As a result of its easy installation and performance, MERAKI ECO BACKLIGHT 282-140 is a perfect partner for professionals in light fixtures production. Excellent items for development of light fixtures and backlighted signage. Its wide ranging colour temperature offers total colours flexibility.

lm/$

>135 lm/w

5Years

Guarantee

In compliance with IEC 62031 / IEC 62471 / IEC 62717

APPLICATION

MERAKI ECO BACKLIGHT 282-140 -LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

PRODUCT DESCRIPTION

Available in 2700K-3000K-4000K-5000K

CRI>80 (CRI90 available) – colours under request

Efficiency > 135 lm/W

Colour tolerance SDCM

Easy to install

Space-saving design

Life-time exceeds 50.000 hrs.

5 years guarantee

High lm/$ relation

Exclusive design (no heatsink required)

Homogeneous and wide beam range

47


MERAKI LED MODULES TECHNOLOGY TECHNICAL DATA

DIMENSIONS

SELV voltage

Available in 2700K/3000K/4000K/5000K

CRI80-90

Operating temperature between -30ºC and 45º C

EN 61471:2008 group 1

Standard Tc 65°C

LED viewing angle 147º BACKLIGHT type

Weight 70 g

MOQ 64 pieces

Possibility to integrate with LOGO Custom

140 110

24

18

47.2

1.60

126.7 5

IMPROVING

ECO BACKLIGHT 282-140-LINEAL CC (280X24 MM)

(*) Measured in mm 280

18

24

125

125

5

1.60

266.6

SPECIFIC TECHNICAL DATA - ECO 140 CODE

CCT

QTY LED

CRI typ.

RATED MIN. STANDARD MAX CURRENT VOLTAGE VOLTAGE VOLTAGE Tc=65ºC (V) (V) (V) (mA)

AVERAGE NOMINAL EFFICIENCIES STANDARD PHOTO CURRENT POWER (lm / W) FLUX METRIC (A) (W) (Im)* CODE

31.13.140.01.3 2700K 31.13.140.01.3 2700K 31.13.140.01.3 2700K

3 3 3

>80 >80 >80

200 350 500

5,7 5,7 5,7

5,95 6,1 5,8

6,2 6,2 6,2

0,202 0,354 0,502

1,202 2,147 2,917

127,922 109,748 110,482

153,75 235,65 322,32

827.348 827.348 827.348

31.13.140.02.3 3000K 31.13.140.02.3 3000K 31.13.140.02.3 3000K

3 3 3

>80 >80 >80

200 350 500

5,7 5,7 5,7

5,95 6,1 5,8

6,2 6,2 6,2

0,202 0,354 0,502

1,202 2,147 2,917

130,119 112,682 112,549

156,39 241,95 328,35

830.348 830.348 830.348

31.13.140.03.3 4000K 31.13.140.03.3 4000K 31.13.140.03.3 4000K

3 3 3

>80 >80 >80

200 350 500

5,7 5,7 5,7

5,95 6,1 5,8

6,2 6,2 6,2

0,202 0,354 0,502

1,202 2,147 2,917

136,958 115,350 111,397

164,61 247,68 324,99

840.348 840.348 840.348

31.13.140.04.3 5000K 31.13.140.04.3 5000K 31.13.140.04.3 5000K

3 3 3

>80 >80 >80

200 350 500

5,7 5,7 5,7

5,95 6,1 5,8

6,2 6,2 6,2

0,202 0,354 0,502

1,202 2,147 2,917

139,454 118,564 121,958

167,61 254,58 355,80

850.348 850.348 850.348

(*) Tolerance range for flux measurements of 8%. (**) It is required to keep Tc < 65ºC. (***) For module supply including high adhesion thermal tape, please add the letter “C” behind the product code. Example: 31.13.140.04.3C.

MERAKI ECO BACKLIGHT 282-140 -LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

48


MERAKI LED MODULES IMPROVING

ECO BACKLIGHT 282-140-LINEAL CC (280X24 MM)

TECHNOLOGY

SPECIFIC TECHNICAL DATA - ECO 282 MIN. STANDARD MAX. AVERAGE RATED CURRENT VOLTAGE VOLTAGE VOLTAGE CURRENT (V) (V) (V) (A) Tc=65ºC (mA)

NOMINAL EFFICIENCIESSTANDARD PHOTOPOWER (lm / W) FLUX METRIC (W) (Im)* CODE

QTY LED

CRI typ.

31.13.282.01.6 2700K 31.13.282.01.6 2700K 31.13.282.01.6 2700K

6 6 6

>80 >80 >80

200 350 500

11,2 11,2 11,2

11,9 12,2 11,5

12,8 12,8 12,8

0,202 0,352 0,503

2,404 4,294 5,785

127,922 109,748 111,443

307,50 471,30 644,64

827.348 827.348 827.348

31.13.282.02.6 3000K 31.13.282.02.6 3000K 31.13.282.02.6 3000K

6 6 6

>80 >80 >80

200 350 500

11,2 11,2 11,2

11,9 12,2 11,5

12,8 12,8 12,8

0,202 0,352 0,503

2,404 4,294 5,785

130,119 112,682 113,528

312,78 483,90 656,70

830.348 830.348 830.348

31.13.282.03.6 4000K 31.13.282.03.6 4000K 31.13.282.03.6 4000K

6 6 6

>80 >80 >80

200 350 500

11,2 11,2 11,2

11,9 12,2 11,5

12,8 12,8 12,8

0,202 0,352 0,503

2,404 4,294 5,785

136,958 115,350 112,366

329,22 495,36 649,98

840.348 840.348 840.348

31.13.282.04.6 5000K 31.13.282.04.6 5000K 31.13.282.04.6 5000K

6 6 6

>80 >80 >80

200 350 500

11,2 11,2 11,2

11,9 12,2 11,5

12,8 12,8 12,8

0,202 0,352 0,503

2,404 4,294 5,785

139,454 118,564 123,018

335,22 509,16 711,60

850.348 850.348 850.348

CODE

CCT

(*) Tolerance range for flux measurements of 8%. (**) It is required to keep Tc < 65ºC. (***) For module supply including high adhesion thermal tape, please add the letter “C” behind the product code. Example: 31.13.140.04.6C.

DRIVER + MODULE CONNECTION EXAMPLE Reccommendation over PCB wire connection:

230 Vac 50/60 Hz

L N

IN

DRIVER V out= 5-10 V 350 mA

MERAKI ECO BACKLIGHT 282-140 -LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

+ OUT

≤ 0,5 mm² (flexible) / ≤ 0,75 mm² (rigid)

-

49


MERAKI LED MODULES IMPROVING

ECO BACKLIGHT 282-140-LINEAL CC (280X24 MM)

TECHNOLOGY

Standard installation example:

N

+

DRIVER Vf: 49,2 V 350 mA

IN

OUT

+

L

+

-

-

-

-

-

+

+

-

-

+

-

+

-

-

+

-

+

-

+

+

-

-

+

-

+

+

+

+

230 Vac 50/60 Hz

1

2

Dissmantle profile base.

For eventual attachment of the fixture (with no use of double sided adhesive tape) drill a hole in the profile.

MERAKI ECO BACKLIGHT 282-140 -LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

50


MERAKI LED MODULES IMPROVING

TECHNOLOGY

ECO BACKLIGHT 282-140-LINEAL CC (280X24 MM)

INSTALLATION AND CONNECTION EXAMPLE

3

(*)

4

Place the PCB and apply pressure. Fix the screws to the

Annex the heatsink. Introduce the positive (+, red) and

fixture base. Accessory: M3 screws. (*) ESD protection to

negative (-, black) wires in the pre-made holes, and connect

earth connection

them to appropriate voltage.

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER MERAKI ECO BACKLIGHT 282-140 must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). Family MERAKI LED MODULES have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. MERAKI LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. Please, verify driver’s min. and max. Vn values specified in this data sheet. ISOLATION MERAKI ECO BACKLIGHT 282-140 functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage of 50V is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION MERAKI ECO BACKLIGHT 282-140 contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu.

MERAKI ECO BACKLIGHT 282-140 -LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

51


MERAKI LED MODULES IMPROVING

TECHNOLOGY

ECO BACKLIGHT 282-140-LINEAL CC (280X24 MM)

MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI ECO BACKLIGHT 282-140 must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source. Thermal transference between PCB and luminaire body must be at its highest, in order to ensure that fixture temperature does not exceed Tc in any case. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs. The module will be delivered with 5 pre-made holes: 4 of D=5 mm and 1 central hole of D=10 mm. Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress. Ideal wire for this connection type is unipolar rigid wire of 0,4-1mm², with a strip wire of 6,5-7MM. To remove wire, push orifice on the connector and pull smoothly. TEMPERATURE MERAKI ECO BACKLIGHT 282-140 life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=65°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%. OPTICAL CHARACTERISTICS + CCT Measurement of LED discrete points may have variations in regards on the CCT temperature here described, with a variance of 3SDCM for white and +/- 5nm for coloured LEDs. CCT shifts +/- 0,001 at 6.000 hrs. 3 SDCM are declared over the complete module. Modules viewing angle is 120°.

MERAKI ECO BACKLIGHT 282-140 -LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

52


MERAKI LED MODULES IMPROVING

TECHNOLOGY

MEDIUM FLUX 282 - LINEAL CC (280X24MM)

New modules MEDIUM FLUX 282 from MERAKI LINEAL CC family are ideal for small size fixtures that require high performance and excellent Im/$ relation. These modules are very simple to connect and to assembly to any surface. Specially indicated for the production of linear lighting, both direct and indirect. The modules have two different functioning: high flux and high efficiency. Depending on its input current, heatsinks could be avoided. Modules are available on diverse CCT and SELV voltage.

lm/$

>140 lm/w

5Years

Guarantee

In compliance with IEC 62031 / IEC 62471 / IEC 62717

PRODUCT DESCRIPTION

APPLICATION

MERAKI MEDIUM FLUX 282 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

Available in 2700K-3000K-4000K-5000K

CRI>80

Efficiency > 140 lm/W

Colour tolerance 3 SDCM

Easy to install

Space-saving design

Life-time exceeds 50.000 hrs.

5 years guarantee

High lm/$ relation

53


MERAKI LED MODULES IMPROVING

MEDIUM FLUX 282 - LINEAL CC (280X24MM)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS

SELV Voltage

Available in 2700-3000-4000-5000K.

Typical CRI80, CRI90 available under request.

Operating temperature between -20ºC and +45°C

EN 61471:2008 group 1

Standard Tc 65°C

LED viewing angle 120°

Weight 25 g

MOQ 44 units

Packaging box weight (approx.) 1100 g

PWM dimmable.

125

24

18

280

125

1.60

4.72

249.65

(*) Measured in mm

SPECIFIC TECHNICAL DATA MIN. STANDARD MAX STANDARD NOMINAL EFFICIENCIES STANDARD PHOTO METRIC VOLTAGE VOLTAGE VOLTAGE CURRENT POWER (lm / W) FLUX CODE (V) (V) (V) (A) (W) (Im)(*)

CODE

CCT

QTY LED

CRI typ.

RATED CURRENT Tc=65ºC (mA)

31.13.07001 31.13.07001 31.13.07001

2700K 2700K 2700K

22 22 22

>80 >80 >80

200 350 500

30,8 30,8 30,8

31,8 32,7 33,5

35,2 35,2 35,2

0,202 0,353 0,502

6,42 11,54 16,81

131,721 125,408 115,422

846,12 1.447,60 1.941,06

827.348 827.348 827.348

31.13.07002 3000 K 31.13.07002 3000 K 31.13.07002 3000 K

22 22 22

>80 >80 >80

200 350 500

30,8 30,8 30,8

31,8 32,7 33,5

35,2 35,2 35,2

0,202 0,352 0,502

6,42 11,51 16,81

135,324 126,726 117,466

869,27 1.458,67 1.975,43

830.348 830.348 830.348

31.13.07003 4000 K 31.13.07003 4000 K 31.13.07003 4000 K

22 22 22

>80 >80 >80

200 350 500

30,8 30,8 30,8

32,2 33,1 33,7

35,2 35,2 35,2

0,202 0,352 0,502

6,50 11,65 16,91

137,180 125,988 118,785

892,28 1.467,91 2.009,53

840.348 840.348 840.348

31.13.07004 31.13.07004 31.13.07004

22 22 22

>80 >80 >80

200 350 500

30,8 30,8 30,8

32,2 33,1 33,7

35,2 35,2 35,2

0,202 0,352 0,502

6,50 11,65 16,91

140,739 128,248 120,798

915,42 1.494,24 2.043,58

850.348 850.348 850.348

5000K 5000K 5000K

(**) It is required to keep Tc < 65ºC. (***) For PCB supply including high adhesion thermal tape, please add the letter “C” behind the product code. Example: 31.13.0625C.

DRIVER + MODULE CONNECTION EXAMPLE

230 Vac 50/60 Hz

L

DRIVER Vf: 65.4V 350 mA

IN

N

Reccommendation over PCB wire connection:

+ OUT

≤ 0,5 mm² (flexible) / ≤ 0,75 mm² (rigid)

-

Ref. 06.345 Conector AÉREO Ref. 06.094 (Opcional)

26mm

Max.6A

249.65 MERAKI MEDIUM FLUX 282 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

54


MERAKI LED MODULES IMPROVING

TECHNOLOGY

MEDIUM FLUX 282 - LINEAL CC (280X24MM)

INSTALLATION AND CONNECTION EXAMPLE

2

1

For eventual attachment of the fixture (with no use of

Place the PCB and apply pressure. Fix the screws to the

double-sided tape) drill a hole in the profile.

fixture base. (*) Accessory: M3 screws.

Max. no. of PCBs: depends on driver type Vf total PCBs ≤ Vout Driver

Connect the

or ect nn co

mo d

3

the board to b ith oa w rd 06.345 e ul R e f.

Place interconnection wires.

Lifetime Derating for MERAKI LINEAL MEDIUM FLUX 282

110.000 100.000 Lifetime ( L80 / B50) h

90.000 80.000 70.000 60.000 50.000 40.000

500 mA (> 48.000 hs)

30.000

350 mA (> 50.000 hs)

20.000 10.000 0 20

30

40

50 60 70 Temperature Tc (°C)

MERAKI MEDIUM FLUX 282 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

80

90

100

55


MERAKI LED MODULES IMPROVING

TECHNOLOGY

MEDIUM FLUX 282 - LINEAL CC (280X24MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER MERAKI MEDIUM FLUX 282must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). Family MERAKI LED MODULES have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. MERAKI LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION MERAKI MEDIUM FLUX 282functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION MERAKI MEDIUM FLUX 282 is contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI MEDIUM FLUX 282 must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source. Thermal transference between PCB and luminaire body must be at its highest, in order to ensure that fixture temperature does not exceed Tc in any case. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs. The module will be delivered with 5 pre-made holes of D=4 mm according to dimensions drawing (ZHAGA L2W2). Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress. Ideal wire for this connection type is unipolar rigid wire of 0,4-1mm², with a strip wire of 6,5-7MM. To remove wire, push orifice on the connector and pull smoothly. TEMPERATURE MERAKI MEDIUM FLUX 282 life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=65°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%. OPTICAL CHARACTERISTICS + CCT Measurement of LED discrete points may have variations in regards on the CCT temperature here described, with a variance of 3SDCM for white and +/- 5nm for coloured LEDs. CCT shifts +/- 0,001 at 6.000 hrs. 3 SDCM are declared over the complete module. Modules viewing angle is 120°.

MERAKI MEDIUM FLUX 282 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

56


MERAKI LED MODULES IMPROVING

TECHNOLOGY

HIGH FLUX 282 - LINEAL CC(282X24MM)

New modules HIGH OUTPUT 282 from MERAKI LINEAL CC family are ideal for small size fixtures that require high performance and excellent Im/$ relation. These modules are very simple to connect and to assembly to any surface. Specially indicated for the production of linear lighting, both direct and indirect. The modules have two different functioning: high flux and high efficiency. Regarding input current, heatsinks could be avoided. Modules are available on diverse CCT and SELV voltage.

lm/$

>180 lm/w

5Years

Guarantee

In compliance with IEC 62031 / IEC 62471 / IEC 62717

PRODUCT DESCRIPTION

APPLICATION

MERAKI HIGH FLUX 282 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

Available in 2700K-3000K-4000K-5000K

CRI>80

Efficiency > 180 lm/W

Colour tolerance 3 SDCM

Easy to install

Space-saving design

Life-time exceeds 50.000 hs

5 years guarantee

High lm/$ relation

57


MERAKI LED MODULES IMPROVING

HIGH FLUX 282 - LINEAL CC(282X24MM)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS

SELV voltage

Available in 2700-3000-4000-5000K.

Typical CRI80, CRI90 under request.

Operating temperature between -20ºC +45°C

EN 61471:2008 Group 1

Standard Tc 65°C

LED viewing angle 120°

Weight 25 g

MOQ 44 units

Packaging box weight (approx.) 1100 gr

PWM Dimmable.

125

24

18

280

125

1.60

4.72

249.65

(*) Measured in mm

SPECIFIC TECHNICAL DATA RATED MIN. STANDARD MAX AVERAGE CURRENT VOLTAGE VOLTAGE VOLTAGE CURRENT Tc=65ºC (V) (V) (V) (A) (mA)

NOMINAL EFICIENCIES STANDARD POWER (lm / W) FLUX (W) (Im)(*)

CODE

CCT

QTY LED

CRI typ.

31.13.07005 31.13.07005 31.13.07005

2700K 2700K 2700K

30 30 30

>80 >80 >80

200 350 500

27 27 27

27,6 28 28,4

33 33 33

0,202 0,353 0,502

5,57 9,88 14,25

157,555 152,246 132,232

974,40 1.991,40 2.111,40

827.348 827.348 827.348

31.13.07006 3000 K 31.13.07006 3000 K 31.13.07006 3000 K

30 30 30

>80 >80 >80

200 350 500

27 27 27

27,6 28 28,4

33 33 33

0,202 0,352 0,502

5,57 9,85 14,25

170,982 164,198 0,000

953,26 1.618,34 2.184,60

830.348 830.348 830.348

31.13.07007 4000 K 31.13.07007 4000 K 31.13.07007 4000 K

30 30 30

>80 >80 >80

200 350 500

27 27 27

27,6 28,1 28,5

33 33 33

0,202 0,352 0,502

5,57 9,89 14,30

184,449 175,073 173,621

1.028,34 1.731,68 2.484,00

840.348 840.348 840.348

31.13.07008 31.13.07008 31.13.07008

30 30 30

>80 >80 >80

200 350 500

27 27 27

27,6 28,1 28,5

33 33 33

0,202 0,352 0,502

5,57 9,89 14,30

197,912 186,529 0,000

1.023,00 1.700,70 2.224,20

850.348 850.348 850.348

5000K 5000K 5000K

PHOTO METRIC CODE

(**) It is required to keep Tc < 65ºC. (***) For PCB supply including high adhesion thermal tape, please add the letter “C” behind the product code. Example: 31.13.0625C

DRIVER + MODULE CONNECTION EXAMPLE

230 Vac 50/60 Hz

L

DRIVER Vf: 56.24V 350 mA

IN

N

Reccommendation over PCB wire connection:

+ OUT

≤ 0,5 mm² (flexible) / ≤ 0,75 mm² (rigid)

-

Ref. 06.345 Wre to wire connector Ref. 06.094 (optional)

26mm

Max.6A

MERAKI HIGH FLUX 282 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

249.65

58


MERAKI LED MODULES IMPROVING

HIGH FLUX 282 - LINEAL CC(282X24MM)

TECHNOLOGY

INSTALLATION AND CONNECTION EXAMPLE

2

1

For eventual attachment of the fixture (with no use of

Place the PCB and apply pressure. Fix the screws to the

double-sided tape) drill a hole in the profile.

fixture base. (*) Accessory: M3 screws.

Max. no. of PCBs: Depends on the used drive Vf total PCBs ≤ Vout Driver

ec

tor

Conne ct mo

3

oard to board ob t co le nn 6.345 du Ref. 0

n ció nta e e nt alim de consta a d te ra Ent orrien c

Place the board to board connectors for interconnection.

Lifetime Derating for MERAKI LINEAL HIGHT OUTPUT 282

110.000 100.000 Lifetime ( L80 / B50) h

90.000 80.000 70.000 60.000 50.000 40.000

500 mA (> 48.000 hs)

30.000

350 mA (> 50.000 hs)

20.000 10.000 0 20

30

40

50 60 70 Temperature Tc (°C)

MERAKI HIGH FLUX 282 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

80

90

100

59


MERAKI LED MODULES IMPROVING

TECHNOLOGY

HIGH FLUX 282 - LINEAL CC(282X24MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER MERAKI HIGH FLUX 282 must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). Family MERAKI LED MODULES have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. MERAKI LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION MERAKI HIGH FLUX 282 functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION MERAKI HIGH FLUX 282 is contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI HIGH FLUX 282 must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source. Thermal transference between PCB and luminaire body must be at its highest, in order to ensure that fixture temperature does not exceed Tc in any case. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs. The module will be delivered with 5 pre-made holes of D=4 mm according to dimensions drawing (ZHAGA L2W2). Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress. Ideal wire for this connection type is unipolar rigid wire of 0,4-1mm², with a strip wire of 6,5-7MM. To remove wire, push orifice on the connector and pull smoothly. TEMPERATURE MERAKI HIGH FLUX 282 life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=65°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%. OPTICAL CHARACTERISTICS + CCT Measurement of LED discrete points may have variations in regards on the CCT temperature here described, with a variance of 3SDCM for white and +/- 5nm for coloured LEDs. CCT shifts +/- 0,001 at 6.000 hrs. 3 SDCM are declared over the complete module. Modules viewing angle is 120°.

MERAKI HIGH FLUX 282 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

60


MERAKI LED MODULES IMPROVING

TECHNOLOGY

HIGH FLUX 284 - LINEAR CC (280X40MM)

New modules HIGHT OUTPUT 284 from MERAKI LINEAL CC family are ideal for small size fixtures that require high performance and connection flexibility. These modules are very simple to connect and to assembly to any surface. They are available for automated assembly by robotic wiring machines. Specially indicated for the production of linear lighting, both direct and indirect. The modules have two different functioning: high flux and high efficiency.

Regarding input current,

heatsinks could be avoided. Modules are available on diverse CCT and SELV voltage.

lm/$

>180 lm/w

5Years

Guarantee

In compliance with IEC 62031 / IEC 62471 / IEC 62717

PRODUCT DESCRIPTION

APPLICATION

MERAKI HIGH FLUX 284 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without priornotice.

Available in 2700K-3000K-4000K-5000K

CRI>80

Efficiency > 180 lm/W

Colour tolerance 3 SDCM

Easy to install

Space-saving design

Life-time exceeds 50.000 hrs.

5 years guarantee

High lm/$ relation

61


MERAKI LED MODULES HIGH FLUX 284 - LINEAR CC (280X40MM)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS

SELV Voltage

Available in 2700-3000-4000-5000K.

Typical CRI80, CRI90 available under request.

Operating temperature between -20ºC and +45°C

EN 61471:2008 group 1

Standard Tc 65°C

LED viewing angle 120°

Weight 40 g

MOQ 44 units

Packaging box weight (approx.)1760 g

PWM Dimmable.

280

1.60

4.72

31

113.63 40

IMPROVING

(*) Measured in mm

SPECIFIC TECHNICAL DATA MIN. STANDARD MAX. RATED AVERAGE CURRENT VOLTAGE VOLTAGE VOLTAGE CURRENT (V) (V) (V) Tc=65ºC (A) (mA)

CODE

CCT

QTY LED

CRI typ.

NOMINAL EFICIENCIESSTANDARD PHOTO (lm / W) METRIC FLUX POWER CODE (Im)(*) (W)

31.13.07013 31.13.07013 31.13.07013

2700K 2700K 2700K

30 30 30

>80 >80 >80

200 350 500

27 27 27

27,5 28,1 28,5

33 33 33

0,202 0,353 0,502

5,55 9,91 14,30

164,986 158,176 146,718

916,50 1.569,00 2.099,10

827.348 827.348 827.348

31.13.07014 31.13.07014 31.13.07014

3000 K 3000 K 3000 K

30 30 30

>80 >80 >80

200 350 500

27 27 27

27,5 28,1 28,5

33 33 33

0,202 0,352 0,502

5,55 9,89 14,30

169,025 160,430 151,299

938,93 1.586,85 2.164,64

830.348 830.348 830.348

31.13.07015 31.13.07015 31.13.07015

4000 K 4000 K 4000 K

30 30 30

>80 >80 >80

200 350 500

27 27 27

27,6 28,1 28,5

33 33 33

0,202 0,352 0,502

5,57 9,89 14,30

186,186 177,400 166,913

1.038,02 1.754,70 2.388,02

840.348 840.348 840.348

31.13.07016 31.13.07016 31.13.07016

5000K 5000K 5000K

30 30 30

>80 >80 >80

200 350 500

27 27 27

27,6 28,1 28,5

33 33 33

0,202 0,352 0,502

5,57 9,89 14,30

203,939 194,355 182,533

1.137,00 1.922,40 2.611,50

850.348 850.348 850.348

(**) It is required to keep Tc < 65ºC. (***) For PCB supply including high adhesion thermal tape, please add the letter “C” behind the product code. Example: 31.13.0625C.

DRIVER + MODULE CONNECTION EXAMPLE

230 Vac 50/60 Hz

L

DRIVER Vf: 56.2V 350 mA

IN

N

Reccommendation over PCB wire connection:

+ OUT

≤ 0,5 mm² (flexible) / ≤ 0,75 mm² (rigid)

-

Ref. 03.100

RIGID wire Ref. 03.100

165mm

Max.3A

RIGID wire Ref. 03.101

45mm

Max.3A

MERAKI HIGH FLUX 284 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without priornotice.

113.63

62


MERAKI LED MODULES IMPROVING

TECHNOLOGY

HIGH FLUX 284 - LINEAR CC (280X40MM)

INSTALLATION AND CONNECTION EXAMPLE

2

1

For eventual attachment of the fixture (with no use of

Place the PCB and apply pressure. Fix the screws to the

double sided tape) drill a hole in the profile.

lighting base. (*) Accessory: M3 screws.

C

Co nn e

3 a.

es and return dul wi o m re 3.100 ct Ref.0

Max. no. of PCBs: depends on used driver: Vf total PCBs â&#x2030;¤ Vout Driver

put e in nt c r ou re er s t cur Pow nstan co

+

-

rn w retu 1 ire .10 se lo ef.03 R

Place interconnection wires.

C

3 b.

ules + an dmod ct e n 0 1 0 . f. 03 on Re

-

+ MERAKI HIGH FLUX 284 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without priornotice.

Place interconnection wire.

63


MERAKI LED MODULES IMPROVING

HIGH FLUX 284 - LINEAR CC (280X40MM)

TECHNOLOGY

Lifetime Derating for MERAKI LINEAL MERAKI 284 HIGHT OUTPUT

110.000 100.000 Lifetime ( L80 / B50) h

90.000 80.000 70.000 60.000 50.000 40.000

500 mA (> 48.000 hs)

30.000

350 mA (> 50.000 hs)

20.000 10.000 0 20

30

40

50 60 70 Temperature Tc (°C)

80

90

100

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER MERAKI HIGH FLUX 284must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). Family MERAKI LED MODULES have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. MERAKI LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION MERAKI HIGH FLUX 284functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION MERAKI HIGH FLUX 284 is contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu.

MERAKI HIGH FLUX 284 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without priornotice.

64


MERAKI LED MODULES IMPROVING

TECHNOLOGY

HIGH FLUX 284 - LINEAR CC (280X40MM)

MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI HIGH FLUX 284 must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source. Thermal transference between PCB and luminaire body must be at its highest, in order to ensure that fixture temperature does not exceed Tc in any case. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs. The module will be delivered with 5 pre-made holes of D=4 mm according to dimensions drawing (ZHAGA L2W4). Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress. Ideal wire for this connection type is unipolar rigid wire of 0,4-1mm², with a strip wire of 6,5-7MM. To remove wire, push orifice on the connector and pull smoothly. TEMPERATURE MERAKI HIGH FLUX 284 life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=65°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%. OPTICAL CHARACTERISTICS + CCT Measurement of LED discrete points may have variations in regards on the CCT temperature here described, with a variance of 3SDCM for white and +/- 5nm for coloured LEDs. CCT shifts +/- 0,001 at 6.000 hrs. 3 SDCM are declared over the complete module. Modules viewing angle is 120°.

MERAKI HIGH FLUX 284 - LINEAL CC - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without priornotice.

65


MERAKI LED MODULES IMPROVING

TECHNOLOGY

LINEAL CV MF - 3012 24V (310X12MM)

Within MERAKI LED MODULES family, we can find 300x12 mm linear modules, ideal for small size fixtures that require high performance and connection flexibility. These modules are very simple to connect and to assembly to any surface, i.e. aluminum, wood or metal. Specially indicated for use in shelves, window display, and similar. The modules have two different functioning: medium flux that requires no additional heatsinks, and high flux. The modules are available on diverse CCT and SELV voltage.

lm/$

>140 lm/w

5Years

Guarantee

In compliance with IEC 62031 / IEC 62471 / IEC 62717

PRODUCT DESCRIPTION

APPLICATION

MERAKI LINEAL CV MF - 3012 24V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

Available in 2700-3000-4000 -5000K

CRI >80 (CRI90 available under request)

Efficiency > 140lm/W

Colour tolerance 3 SDCM

Space-saving design

Facilitates installation

Life-time exceeds 50.000 hrs

Voltage 24Vcc

66


MERAKI LED MODULES IMPROVING

LINEAL CV MF - 3012 24V (310X12MM)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS

Available in 2700K/3000K/4000K/5000K

Typical CRI80 (CRI90 available under request)

Operating temperature between -30ºC and 45ºC

EN 61471:2008 group 1

Standard Tc 75ºC

LED viewing angle 120º

Weight 12 g

MOQ 60 pieces

Packaging box weight 1100 g

45

SPECIFIC TECHNICAL DATA

1.60

(*) Measured in mm

2.50

SELV voltage

12

310

292

Module for board to board connector: A

Board to board connector Ref. 06.345

26 mm

Max.6A

CODE

CCT

70mA:16R

31.13.0640/A 31.13.0641/A 31.13.0642/A 31.13.0643/A

2700k 3000k 4000k 5000k

24 24 24 24

134 134 134 134

3.23 3,26 3,24 3,24

378,51 450,28 463,60 505,40

100mA: 10R

31.13.0650/A 31.13.0651/A 31.13.0652/A 31.13.0653/A

2700k 3000k 4000k 5000k

24 24 24 24

195 195 195 195

4,62 4,69 4,74 4,74

532,76 631,43 663,68 679,00

Máximo 15 PCB`s 4.5 Mts

Máximo 11 PCB`s 3,5 mts

ELECTRICAL RATED POWER CURRENT (VCC) Tc=65ºC (mA)

NOMINAL POWER (W)

STANDARD EFFICIENCY FLUX (lm / W) (Im)(*)

CRI typ.

QTY LED

PHOTOMETRIC CODE

117,072 137,723 142,749 155,621

> 82 > 82 > 82 > 82

14 14 14 14

827.348 827.348 827.348 827.348

115,260 134,495 139,923 143,152

> 82 > 82 > 82 > 82

14 14 14 14

827.348 827.348 827.348 827.348

(*) Optical and electric measures with tolerance of +/- 10%. (**) For higher fluxes (100mA) is required to keep Tc < 65ºC, with heatsink (not included). (***) For PCB supply including high adhesion thermal tape, please add the letter “C” behind the product code. Example: 31.13.0625C.

DRIVER + MODULE CONNECTION EXAMPLE

230 Vac 50/60 Hz

L N

IN

DRIVER 24 Vcc

+ OUT

Reccommendation over PCB wire connection: ≤ 0,5 mm² (flexible) / ≤ 0,75 mm² (rigid)

-

WHIRE TO BOARD CONNECTOR

MERAKI LINEAL CV MF - 3012 24V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

67


MERAKI LED MODULES IMPROVING

LINEAL CV MF - 3012 24V (310X12MM)

TECHNOLOGY

Módulo para conector rígido:

B

RIGID wire Ref. 51.002

50 mm

Max.3A

ELECTRCAL RATED POWER CURRENT Tc=65ºC (VCC) (mA)

NOMINAL POWER (W)

STANDARD EFFICIENCY FLUX (lm / W) (Im)(*)

CODE

CCT

70mA:16R

31.13.0640/B 31.13.0641/B 31.13.0642/B 31.13.0643/B

2700k 3000k 4000k 5000k

24 24 24 24

134 134 134 134

3.23 3,26 3,24 3,24

378,51 450,28 463,60 505,40

100mA: 10R

31.13.0650/B 31.13.0651/B 31.13.0652/B 31.13.0653/B

2700k 3000k 4000k 5000k

24 24 24 24

195 195 195 195

4,62 4,69 4,74 4,74

532,76 631,43 663,68 679,00

Máximo 15 PCB`s 4.5 Mts

Máximo 11 PCB`s 3,5 mts

Tc max 75º

258

CRI typ.

QTY LED

PHOTOMETRIC CODE

117,072 137,723 142,749 155,621

> 82 > 82 > 82 > 82

14 14 14 14

827.348 827.348 827.348 827.348

115,260 134,495 139,923 143,152

> 82 > 82 > 82 > 82

14 14 14 14

827.348 827.348 827.348 827.348

(*) Optical and electric measures with tolerance of +/- 10%. (**) For higher fluxes (100mA) is required to keep Tc < 65ºC, with heatsink (not included). (***) For PCB supply including high adhesion thermal tape, please add the letter “C” behind the product code. Example: 31.13.0625C.

DRIVER + MODULE CONNECTION EXAMPLE

230 Vac 50/60 Hz

L

DRIVER 24 Vcc

IN

N

+ OUT

Reccommendation over PCB wire connection: ≤ 0,5 mm² (flexible) / ≤ 0,75 mm² (rigid)

-

CONNECTOR WIRE

Lifetime Derating for MERAKI CIRCULAR CV - MEDIUM FLUX 110.000 100.000 Lifetime ( L80 / B50) h

90.000 80.000 70.000 60.000 50.000 40.000

100 mA (> 48.000 hs)

30.000

70 mA (> 50.000 hs)

20.000 10.000 0 20

30

40

50 60 70 Temperature Tc (°C)

MERAKI LINEAL CV MF - 3012 24V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

80

90

100

68


MERAKI LED MODULES IMPROVING

TECHNOLOGY

LINEAL CV MF - 3012 24V (310X12MM)

INSTALLATION AND CONNECTION EXAMPLE

2

1

If no use of thermal tape with high adhesion properties.

For eventual attachment of the fixture (with no use of double

Place the PCB and apply pressure. Fix the screws to the

sided tape) drill a hole in the profile.

fixture base. (*) Accessory: M3 screws.

4 +

3

Please, remember to specify the exact desired position for the connector.

Place the board to board connectors for interconnection.

Introduce the positive (+, red) and negative (-, black) wires in the pre-made holes, and connect them to appropriate voltage.

MERAKI LINEAL CV MF - 3012 24V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

69


MERAKI LED MODULES IMPROVING

TECHNOLOGY

LINEAL CV MF - 3012 24V (310X12MM)

INFORMACIÓN DE SEGURIDAD E INSTALACIÓN. ELECTRICAL POWER MERAKI HIGH LINEAR 3012 must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). Family MERAKI LED MODULES have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. MERAKI LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION MERAKI HIGH LINEAR 3012 functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage of 50V is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION MERAKI HIGH LINEAR 3012 is contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI HIGH LINEAR 3012 must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source. Thermal transference between PCB and luminaire body must be at its highest, in order to ensure that fixture temperature does not exceed Tc in any case. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs. The module will be delivered with 5 pre-made holes of D=4 mm according to dimensions drawing (ZHAGA L2W4). Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress. Ideal wire for this connection type is unipolar rigid wire of 0,4-1mm², with a strip wire of 6,5-7MM. To remove wire, push orifice on the connector and pull smoothly. TEMPERATURE MERAKI HIGH LINEAR 3012life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=75°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%. OPTICAL CHARACTERISTICS + CCT Measurement of LED discrete points may have variations in regards on the CCT temperature here described, with a variance of 3SDCM for white and +/- 5nm for coloured LEDs. CCT shifts +/- 0,001 at 6.000 hrs. 3 SDCM are declared over the complete module. Modules viewing angle is 120°.

MERAKI LINEAL CV MF - 3012 24V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

70


MERAKI LED MODULES IMPROVING

TECHNOLOGY

LINEAL CV MF - 1512 24V (300X12MM)

Within MERAKI LED MODULES family, we can find 150x12 mm linear modules, ideal for small size fixtures that require high performance and connection flexibility. These modules are very simple to connect and to assembly to any surface, i.e. aluminum, wood or metal. Specially indicated for use in shelves, window display, and similar. The modules have two different functioning: medium flux that require no additional heatsinks, and high flux. Modules are available on diverse CCT and SELV voltage.

lm/$

>140 lm/w

5Years

Guarantee

In compliance with IEC 62031 / IEC 62471 / IEC 62717

APPLICATION

MERAKI LINEAL MCV MF - 1512 - 24V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

PRODUCT DESCRIPTION

Available in 2700-3000-4000 -5000K

CRI >80 (CRI 90 available under request)

Efficiency > 140lm/W

Colour tolerance 3 SDCM

Space-saving design

Easy to install

Life-time exceeds 50.000 hrs

Voltage 24Vcc

71


MERAKI LED MODULES IMPROVING

LINEAL CV MF - 1512 24V (155X12MM)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS

SELV voltage

Available in 2700K/3000K/4000K/5000K

Typical CRI80 (CRI90 available under request)

155

Operating temperature between -30ºC and 45ºC

66.44

EN 61471:2008 group 1

Standard Tc 75ºC

LED viewing angle120º

Weight 6 g

MOQ 60 pieces

Packaging box weight (approx.) 550 g

44.29

1.6

2.50

4.15

12

(*) Measured in mm

SPECIFIC TECHNICAL DATA Board to board connector module: A

Wire to board connector Ref. 06.345

26 mm

Max.6A 136,91

CODE

CCT

POWER SUPPLY (VCC)

RATED CURRENT Tc=65ºC (mA)

NOMINAL POWER (W)

70mA:16R

31.13.0625/A 31.13.0626/A 31.13.0627/A 31.13.0628/A

2700k 3000k 4000k 5000k

24 24 24 24

69 69 69 69

1,61 1,61 1,64 1,64

190,40 210,00 227,50 249,20

100mA: 10R

31.13.0630/A 31.13.0631/A 31.13.0632/A 31.13.0633/A

2700k 3000k 4000k 5000k

24 24 24 24

97 97 97 97

2,31 2,34 2,34 2,34

259,08 302,97 313,66 332,50

Máximo 30 PCB`s 4.5 Mts

Máximo 22 PCB`s 3,5 mts

STANDARD EFFICIENCY FLUX (lm / W) (Im)(*)

CRI typ.

QTY LED

PHOTOMETRIC CODE

117,958 129,711 138,451 151,657

> 82 > 82 > 82 > 82

7 7 7 7

827.348 827.348 827.348 827.348

111,987 129,201 133,895 141,939

> 82 > 82 > 82 > 82

7 7 7 7

827.348 827.348 827.348 827.348

(*) Optical and electric measures with tolerance of +/- 10% (**) For higher fluxes (100mA) is required to keep Tc < 65ºC, with heatsink (not included) (***) For PCB supply including high adhesion thermal tape, please add the letter “C” behind the product code. Example: 31.13.0633/AC

DRIVER + MODULE CONNECTION EXAMPLE

230 Vac 50/60 Hz

L N

IN

DRIVER 24 Vcc

+ OUT

Reccommendation over PCB wire connection:: ≤ 0,5 mm² (flexible) / ≤ 0,75 mm² (rigid)

-

WIRE CONNECTOR

MERAKI LINEAL MCV MF - 1512 - 24V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

72


MERAKI LED MODULES IMPROVING

LINEAL CV MF - 1512 24V (155X12MM)

TECHNOLOGY

Module for rigid connector:

B

Tc max 75 º

RIGID wire Ref. 51.002

50 mm

Max.3A

101.01 CCT ELECTRICAL RATED CURRENT SUPPLY Tc=65ºC (VCC) (mA)

CODE

NOMINAL POWER (W)

STANDARD EFFICIENCY FLUX (lm / W) (Im)(*)

CRI typ.

QTY LED

PHOTOMETRIC CODE

70mA:16R

31.13.0625/B 31.13.0626/B 31.13.0627/B 31.13.0628/B

2700k 3000k 4000k 5000k

24 24 24 24

69 69 69 69

1,61 1,61 1,64 1,64

190,40 210,00 227,50 249,20

117,958 129,711 138,451 151,657

> 82 > 82 > 82 > 82

7 7 7 7

827.348 827.348 827.348 827.348

100mA: 10R

31.13.0630/B 31.13.0631/B 31.13.0632/B 31.13.0633/B

2700k 3000k 4000k 5000k

24 24 24 24

97 97 97 97

2,31 2,34 2,34 2,34

259,08 302,97 313,66 332,50

111,987 129,201 133,895 141,939

> 82 > 82 > 82 > 82

7 7 7 7

827.348 827.348 827.348 827.348

Máximo 30 PCB`s 4.5 Mts

Máximo 22 PCB`s 3,5 mts

(*) Optical and electric measures with tolerance of +/- 10%. (**) For higher fluxes (100mA) is required to keep Tc < 65ºC, with heatsink (not included). (***) For PCB supply including high adhesion thermal tape, please add the letter “C” behind the product code. Example: 31.13.0633/BC.

DRIVER + MODULE CONNECTION EXAMPLE

230 Vac 50/60 Hz

L

DRIVER 24 Vcc

IN

N

+ OUT

Reccommendation over PCB wire connection:: ≤ 0,5 mm² (flexible) / ≤ 0,75 mm² (rigid)

-

WIRE CONNECTOR

Lifetime Derating for MERAKI CIRCULAR CV - MEDIUM FLUX 110.000 100.000 Lifetime ( L80 / B50) h

90.000 80.000 70.000 60.000 50.000 40.000

100 mA (> 48.000 hs)

30.000

70 mA (> 50.000 hs)

20.000 10.000 0 20

30

40

50 60 70 Temperature Tc (°C)

MERAKI LINEAL MCV MF - 1512 - 24V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

80

90

100

73


MERAKI LED MODULES IMPROVING

TECHNOLOGY

LINEAL CV MF - 1512 24V (155X12MM)

INSTALLATION AND CONNECTION EXAMPLE

2

1

For eventual attachment of the fixture (with no use of

Place the PCB and apply pressure. Fix the screws to

double sided tape) drill a hole in the profile.

the fixture base. (*) Accessory: M3 screws.

4 +

3

Please, remember to specify the exact desired position for the connector.

Place the board to board connectors for interconnection.

Introduce the positive (+, red) and negative (-, black) wires in the pre-made holes, and connect them to appropriate voltage.

MERAKI LINEAL MCV MF - 1512 - 24V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

74


MERAKI LED MODULES IMPROVING

TECHNOLOGY

LINEAL CV MF - 1512 24V (155X12MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER MERAKI HIGH LINEAR 1512 must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). Family MERAKI LED MODULES have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. MERAKI LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION MERAKI HIGH LINEAR 1512 functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage of 50V is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION MERAKI HIGH LINEAR 1512 contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI HIGH LINEAR 1512 must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source. Thermal transference between PCB and luminaire body must be at its highest, in order to ensure that fixture temperature does not exceed Tc in any case. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs. The module will be delivered with 5 pre-made holes: 4 of D=5 mm and 1 central hole of D=10 mm. Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress. Ideal wire for this connection type is unipolar rigid wire of 0,4-1mm², with a strip wire of 6,5-7MM. To remove wire, push orifice on the connector and pull smoothly. TEMPERATURE MERAKI HIGH LINEAR 1512life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=65°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%. OPTICAL CHARACTERISTICS + CCT Measurement of LED discrete points may have variations in regards on the CCT temperature here described, with a variance of 3SDCM for white and +/- 5nm for coloured LEDs. CCT shifts +/- 0,001 at 6.000 hrs. 3 SDCM are declared over the complete module. Modules viewing angle is 120°.

MERAKI LINEAL MCV MF - 1512 - 24V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

75


MERAKI LED MODULES IMPROVING

TECHNOLOGY

ROUND 155/70 CC AND CV(D=70/155MM)

New MERAKI ROUND 155-70 are ideal to complete round or square designed light fixtures that require high efficiency and flexibility. These LED modules are capable to replace fluorescence downlights of 2x26W with no need to replace the whole fixture, meaning direct cost saving. At nominal power they do not need heatsinks. As a result of its easy installation and performance, is a perfect partner for professionals in light fixtures production. MERAKI ROUND 155-70 modules are excellent items for development of light fixtures and cost saving (vs. former technologies). Versions at constant voltage offer total flexibility.

lm/$

>175 lm/w

5Years

Guarantee

In compliance with IEC 62031 / IEC 62471 / IEC 62717

APPLICATION

PRODUCT DESCRIPTION

Available in 2700K-3000K-4000K-5000K

CRI>80 (CRI90 available under request)

Efficiency > 175 lm/W

Colour tolerance SDCM

Easy to install

Space-saving design

Life-time exceeds 50.000 hrs.

5 years guarantee

High lm/$ relation

Exclusive design (no heatsink required)

Direct cost saving

Extremely flat profile: 8mm

Light weighted. Possibility to place module over heatsink or crystal.

MERAKI ROUND 155/70 CC AND CV- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

76


MERAKI LED MODULES IMPROVING

ROUND 155/70 CC AND CV(D=70/155MM)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS

SELV voltage

Available in 2700K/3000K/4000K/5000K

CRI>80 (CRI 90 available under request)

Operating temperature between -30ºC and 45º C

EN 61471:2008 group 1

Standard Tc 65°C

LED viewing angle 120°

Weight 60 gr

MOQ 32 pieces

Possibility to integrate with LOGO Custom

R

77

.5 0

MERAKI ROUND 155CC

148 69

R5 29.5 94.9

5

R5

66.8 49.2

R

35

MERAKI ROUND 70 CC

29.50

5

(*) Measured in mm

SPECIFIC TECHNICAL DATA - MERAKI ROUND 70 CC CODE

CCT

QTY LED

CRI

RATEDL CURRENT (mA)

31.13.70.CC.02 31.13.70.CC.02 31.13.70.CC.02 31.13.70.CC.02

2700k 2700k 2700k 2700k

24 24 24 24

>80 >80 >80 >80

200 350 400 500

16.2 16.2 16.2 16.2

17,1 17,9 18,1 18,4

19,2 19,2 19,2 19,2

0,201 0,350 0,401 0,504

3,437 6,265 7,258 9,274

127,992 118,602 107,665 109,032

439,92 743,04 781,44 1011,12

827.348 827.348 827.348 827.348

31.13.70.CC.03 31.13.70.CC.03 31.13.70.CC.03 31.13.70.CC.03

3000K 3000K 3000K 3000K

24 24 24 24

>80 >80 >80 >80

200 350 400 500

16.2 16.2 16.2 16.2

17,1 17,9 18,1 18,4

19,2 19,2 19,2 19,2

0,201 0,350 0,401 0,504

3,437 6,265 7,258 9,274

136,720 123,658 115,005 115,864

469,92 774,72 834,72 1074,48

830.348 830.348 830.348 830.348

31.13.70.CC.04 31.13.70.CC.04 31.13.70.CC.04 31.13.70.CC.04

4000K 4000K 4000K 4000K

24 24 24 24

>80 >80 >80 >80

200 350 400 500

16.2 16.2 16.2 16.2

17,1 17,9 18,1 18,4

19,2 19,2 19,2 19,2

0,201 0,350 0,401 0,504

3,437 6,265 7,258 9,274

146,984 128,830 115,733 117,857

505,20 807,12 840,00 1092,96

840.348 840.348 840.348 840.348

31.13.70.CC.05 31.13.70.CC.05 31.13.70.CC.05 31.13.70.CC.05

5000K 5000K 5000K 5000K

24 24 24 24

>80 >80 >80 >80

200 350 400 500

16.2 16.2 16.2 16.2

17,1 17,9 18,1 18,4

19,2 19,2 19,2 19,2

0,201 0,350 0,401 0,504

3,437 6,265 7,258 9,274

171,074 141,702 127,306 129,011

588,00 887,76 924,00 1196,40

850.348 850.348 850.348 850.348

MIN STANDARD MAX AVERAGE VOLTAGE VOLTAGE VOLTAGE CURRENT (V) (*) (V) (*) (V) (*) (A)

NOMINAL LUMINOUS TOTAL POWER EFFICACY FLUX

PHOTO METRIC CODE

(*) Optical and electric measures with tolerance of +/- 10%. (**) For higher fluxes (500mA) is required to keep Tc < 65ºC, with heatsink (not included). MERAKI ROUND 155/70 CC AND CV- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

77


MERAKI LED MODULES IMPROVING

ROUND 155/70 CC AND CV(D=70/155MM)

TECHNOLOGY

SPECIFIC TECHNICAL DATA MERAKI ROUND 70 CV CODE

TOTAL FLUX

PHOTO METRIC CODE

118,602

743,04

827.348

6,265

123,658

774,72

830.348

0,350

6,265

128,830

807,12

840.348

0,350

6,265

141,702

887,76

850.348

CCT

QTY LED

CRI

RATED STANDARD AVERAGE NOMINAL LUMINOUS CURRENT VOLTAGE CURRENT POWER EFFICACY (mA) (V) (*) (A)

31.13.70.CV.02.24

2700k

24

>80

400

17,9

0,350

6,265

31.13.70.CV.03.24

3000K

24

>80

400

17,9

0,350

31.13.70.CV.04.24

4000K

24

>80

400

17,9

31.13.70.CV.05.24

5000K

24

>80

400

17,9

(*) Optical and electric measures with tolerance of +/- 10%. (**) For higher fluxes (500mA) is required to keep Tc < 65ยบC, with heatsink (not included).

SPECIFIC TECHNICAL DATA - MERAKI ROUND 155 CC CODE

CCT

QTY LED

CRI

RATED CURRENT (mA)

MIN STNDARS MAX AVERAGE VOLTAGE VOLTAGE VOLTAGE CURRENT (V) (*) (V) (*) (V) (*) (A)

NOMINAL LUMINOUS TOTAL POWER EFFICACY FLUX

PHOTO METRIC CODE

MERAKI ROUND 150 CC 31.13.155.CC.02 31.13.155.CC.02 31.13.155.CC.02 31.13.155.CC.02

2700K 2700K 2700K 2700K

48 48 48 48

>80 >80 >80 >80

200 350 400 500

32.4 32.4 32.4 32.4

34,4 36,1 36,6 36,6

38,4 38,4 38,4 38,4

0,201 0,350 0,401 0,504

6,914 12,635 14,713 18,446

127,247 120,389 110,921 109,62

879,84 1521,12 1632,00 2022,24

827.348 827.348 827.348 827.348

31.13.155.CC.03 31.13.155.CC.03 31.13.155.CC.03 31.13.155.CC.03

3000K 3000K 3000K 3000K

48 48 48 48

>80 >80 >80 >80

200 350 400 500

32.4 32.4 32.4 32.4

34,4 36,1 36,6 36,6

38,4 38,4 38,4 38,4

0,201 0,350 0,401 0,504

6,914 12,635 14,713 18,446

135,925 122,631 119,403 116,498

939,84 1549,44 1732,80 2148,96

830.348 830.348 830.348 830.348

31.13.155.CC.04 31.13.155.CC.04 31.13.155.CC.04 31.13.155.CC.04

4000K 4000K 4000K 4000K

48 48 48 48

>80 >80 >80 >80

200 350 400 500

32.4 32.4 32.4 32.4

34,4 36,1 36,6 36,6

38,4 38,4 38,4 38,4

0,201 0,350 0,401 0,504

6,914 12,635 14,713 18,446

146,130 138,700 126,273 120,973

1010,40 1752,48 1852,80 2231,52

840.348 840.348 840.348 840.348

31.13.155.CC.05 31.13.155.CC.05 31.13.155.CC.05 31.13.155.CC.05

5000K 5000K 5000K 5000K

48 48 48 48

>80 >80 >80 >80

200 350 400 500

32.4 32.4 32.4 32.4

34,4 36,1 36,6 36,6

38,4 38,4 38,4 38,4

0,201 0,350 0,401 0,504

6,914 12,635 14,713 18,446

167,997 139,802 130,649 129,716

1161,60 1766,40 1896,00 2392,80

850.348 850.348 850.348 850.348

(*) Optical and electric measures with tolerance of +/- 10%. (**) For higher fluxes (500mA) is required to keep Tc < 65ยบC, with heatsink (not included).

MERAKI ROUND 155/70 CC AND CV- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

78


MERAKI LED MODULES IMPROVING

ROUND 155/70 CC AND CV(D=70/155MM)

TECHNOLOGY

SPECIFIC TECHNICAL DATA MERAKI ROUND 155 CV CODE

TOTAL FLUX

PHOTO METRIC CODE

87,448

1611,84

827.348

18,432

93,359

1720,80

830.348

0,768

18,432

96,901

1786,08

840.348

0,768

18,432

100,443

1851,36

850.348

CCT

QTY LED

CRI

RATED STANDARD AVERAGE NOMINAL LUMINOUS CURRENT VOLTAGE CURRENT POWER EFFICACY (mA) (V) (*) (A)

31.13.155.CV.02

2700k

48

>80

800

24

0,768

18,432

31.13.155.CV.03

3000K

48

>80

800

24

0,768

31.13.155.CV.04

4000K

48

>80

800

24

31.13.155.CV.05

5000K

48

>80

800

24

(*) Optical and electric measures with tolerance of +/- 10%. (**) For higher fluxes (500mA) is required to keep Tc < 65ºC, with heatsink (not included).

DRIVER + MODULE CONNECTION EXAMPLE 230 Vcc 50/60 Hz

L

Reccommendation over PCB wire connection:

N

≤ 0,5 mm² (strand) / ≤ 0,75 mm² (solid)

IN

DRIVER 350mA

+ OUT

-

MERAKI R OU ND

C

C MERAKI ROUND 155/70 CC AND CV- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

*Possible to connect up to 5 PCB´s in parallel.

79


MERAKI LED MODULES IMPROVING

ROUND 155/70 CC AND CV(D=70/155MM)

TECHNOLOGY 230 Vcc 50/60 Hz

Reccommendation over PCB wire connection: ≤ 0,5 mm² (Flexible) / ≤ 0,75 mm² (Rigid)

L

N IN

+

DRIVER 350mA

OUT

-

ME

RAKI ROUN D C

C

INSTALLATION AND CONNECTION EXAMPLE

1

2

Dismantle profile base.

For eventual attachment of the fixture (with no use of double sided adhesive tape) drill a hole in the profile.

MERAKI ROUND 155/70 CC AND CV- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

80


MERAKI LED MODULES IMPROVING

TECHNOLOGY

ROUND 155/70 CC AND CV(D=70/155MM)

3

4 -

+

Place the PCB and apply pressure. Fix the screws to the

Introduce the positive (+, red) and negative (-, black) wires

fixture base. (*)Accessory: M3 screws.

in the pre-made holes, and connect them to appropriate voltage.

5

PCB is installed.

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER MERAKI ROUND 155-70 CC AND CV must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). Family MERAKI LED MODULES have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. MERAKI LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. Please, verify driverâ&#x20AC;&#x2122;s min. and max. Vn values specified in this data sheet. ISOLATION MERAKI ROUND 155-70 CC AND CV functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage of 50V is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation.

MERAKI ROUND 155/70 CC AND CV- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

81


MERAKI LED MODULES IMPROVING

TECHNOLOGY

ROUND 155/70 CC AND CV(D=70/155MM)

ESD – STATIC ELECTRICITY INFORMATION MERAKI ROUND 155-70 CC AND CV contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI ROUND 155-70 CC AND CV must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source. Thermal transference between PCB and luminaire body must be at its highest, in order to ensure that fixture temperature does not exceed Tc in any case. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs, and other electronic components. The module will be delivered with 5 pre-made holes: 4 holes of D=5 mm and 1 central hole of D=10mm. Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress. Ideal wire for this connection type is unipolar solid wire of 0,4-1mm², with a strip wire of 6,5-7MM. To remove wire, push orifice on the connector and pull smoothly. TEMPERATURE MERAKI ROUND 155-70 CC AND CV life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=65°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%. OPTICAL CHARACTERISTICS + CCT Measurement of LED discrete points may have variations in regards on the CCT temperature here described, with a variance of 3SDCM for white and +/- 5nm for coloured LEDs. CCT shifts +/- 0,001 at 6.000 hrs. 3 SDCM are declared

MERAKI ROUND 155/70 CC AND CV- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

82


MERAKI LED MODULES IMPROVING

TECHNOLOGY

AC DIRECT 280MM 230V-LINEAL AC (280X24 MM)

MERAKI AC DIRECT 282MM 230V are ideal to complete linear or square designed light fixtures that require high flexibility and direct connection electrical network. These LED modules are capable to replace light tubes of 2x58W with no need to replace the whole fixture, meaning direct cost saving. At nominal power they do not need heatsinks. As a result of its easy installation and performance, MERAKI AC DIRECT 282MM 230V is a perfect partner for professionals in light fixtures production. The modules are excellent items for development of light fixtures and cost saving (vs. former technologies). The module incorporates electronic components to function on direct voltage of 230Vac.

lm/$

>110 lm/w

5Years

Guarantee

In compliance with EN 55015 / EN 62471 / EN 61000

APPLICATION

MERAKI AC DIRECT 282 MM 230V - LINEAL AC - V.1.1_ES- www.idled.eu Reservado el derecho de realizar modificaciones sin previo aviso.

PRODUCT DESCRIPTION

Available in 2700K-3000K-4000K-5000K

CRI > 80 (CRI90 available under request)

Ideal for new or existing luminaires

Efficiency > 110 lm/W

Colour tolerance 3 SDCM

Space-saving design

Life-time exceeds 40.000 hrs.

High lm/$ relation

Integral solutions, no drivers required

Direct voltage connection to 230Vac

Extremely flat profile < 10mm

83


MERAKI LED MODULES TECHNOLOGY TECHNICAL DATA

DIMENSIONS

Voltage 210-240 Vac / 50-60 Hz

Available from 2700K to 5000K

THD < 20%

Power factor > 0.9

Typical CRI80 (CRI90 available under request)

Operating temperature between -30ºC and 45ºC

EN 61471:2008 group 1

Standard Tc 65ºC

LED viewing angle 120°

Weight 100 g

MOQ 100 units

Possible to integrate with LOGO Custom

1.60 5

18

280 250 24

IMPROVING

AC DIRECT 280MM 230V-LINEAL AC (280X24 MM)

SPECIFIC TECHNICAL DATA CODE

31.13.AC.282.01 31.13.AC.282.02 31.13.AC.282.03 31.13.AC.282.04

CCT

QTY LED

CRI

P.F.

RATED CURRENT Tc=75ºC (mA)

STANDARD VOLTAGE (V)

THD (%)

NOMINAL POWER (W)

LUMINOUS EFFICACY

TOTAL FLUX

PHOTOMETRIC CODE

2700K 3000K 4000K 5000K

24 24 24 24

>80 >80 >80 >80

>0.9 >0.9 >0.9 >0.9

39.08 39.08 39.08 39.08

220-240 220-240 220-240 220-240

<20% <20% <20% <20%

8.990 8.990 8.990 8.990

97.976 102.514 115.328 123.337

880.80 921.60 1036.80 1108.80

827.348 830.348 840.348 850.348

DRIVER + MODULE CONNECTION EXAMPLE

Recommendation over PCB wire connection: ≤ 0,5 mm² (strand) / ≤ 0,75 mm² (solid) 210-240 Vac 50/60 Hz

N L

MERAKI AC DIRECT 282 MM 230V - LINEAL AC - V.1.1_ES- www.idled.eu Reservado el derecho de realizar modificaciones sin previo aviso.

84


MERAKI LED MODULES IMPROVING

AC DIRECT 280MM 230V-LINEAL AC (280X24 MM)

TECHNOLOGY

INSTALLATION AND CONNECTION EXAMPLE

2

1

For eventual attachment of the fixture (with no use of double

Place the PCB and apply pressure. Fix the screws to the

sided adhesive tape) drill a hole in the profile.

fixture base. Accessory: M3 screws.

Max. no. of PCBs: Depends on driver type Vf total PCBs ≤ Vout Driver

The must be insulated to avoid contact with active parts ACC COVER TRANSP

Lifetime Derating for MERAKI AC DIRECT 282MM 230V 110.000 100.000 90.000 Lifetime ( L80 / B50) h

3

C

(*) ESD protection to earth connection.

r los módulos cta e on

80.000 70.000 60.000 50.000 40.000

500 mA (> 48.000 hs)

30.000

350 mA (> 50.000 hs)

20.000 10.000 0 20

30

40

50 60 70 Temperature Tc (°C)

MERAKI AC DIRECT 282 MM 230V - LINEAL AC - V.1.1_ES- www.idled.eu Reservado el derecho de realizar modificaciones sin previo aviso.

80

90

100

85


MERAKI LED MODULES IMPROVING

TECHNOLOGY

AC DIRECT 280MM 230V-LINEAL AC (280X24 MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER MERAKI AC DIRECT 282MM 230V must be feed at constant and steady current of 210-240 Vac and 50-60 Hz. MERAKI AC DIRECT series from MERAKI family do not have polarity, this is due to the nature of its electrical power supply. For this reason all its parameters in this data sheet specified and rated current and nominal power must be respected and taken into account. If that is not the case, the module might be irreversibly damaged. MERAKI AC DIRECT 282MM 230V require specific protection against voltage picks or electrical network noise.

ISOLATION MERAKI AC DIRECT 282MM 230V functions with greater voltage than SELV. Hence, it is required isolation with active components. It will be mandatory earth connection on all conductive components of the fixture or light engine. ESD – INFORMACIÓN SOBRE ESTÁTICA MERAKI AC DIRECT 282MM 230V contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI AC DIRECT 282MM 230V must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs and electronic components. The module will be delivered with 5 pre-made fastening holes: 4 through holes of D=5MM and 1 central hole of D=10MM. Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress on the PCB. Always avoid mechanical stress, compression stress or superficial voltage stress over the electronic components and/or driver holder. It is recommended to use nylon screws or similar to increase isolation with active components. Ideal wire for this connection type is unipolar solid wire of 0,4-1mm², with a strip wire of 6,5-7MM. To remove wire, push orifice on the connector and pull smoothly. TEMPERATURA MERAKI AC DIRECT 282MM 230V life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=70°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%. OPTICAL CHARACTERISTICS + CCT Measurement of LED discrete points may have variations in regards on the CCT temperature here described, with a variance of 3SDCM and 2SDCM for white and +/- 5nm for coloured LEDs. CCT shifts +/- 0,001 at 6.000 hrs. 3 SDCM are declared over the complete module. Modules viewing angle is 120°.

MERAKI AC DIRECT 282 MM 230V - LINEAL AC - V.1.1_ES- www.idled.eu Reservado el derecho de realizar modificaciones sin previo aviso.

86


MERAKI LED MODULES IMPROVING

AC DIRECT 155/70MM 230 VAC ROUND(70-155MM)

TECHNOLOGY

MERAKI ROUND 155-70 AC DIRECT are ideal to complete circular or square designed light fixtures that require high flexibility and direct connection electrical network. These LED modules are capable to replace fluorescence downlights of 2x26W with no need to replace the whole fixture, meaning direct cost saving. At nominal power they do not need heatsinks. As a result of its easy installation and performance, MERAKI ROUND 155-70 AC is a perfect partner for professionals in light fixtures production. The modules are excellent items for development of light fixtures and cost saving (vs. former technologies). The module incorporates electronic components to function on direct voltage of 230Vac.

lm/$

>120 lm/w

5Years

Guarantee

In compliance with EN 55015 / EN 62031 / EN 62717 / EN61000

APPLICATION

MERAKI AC DORECT 155/70MM 230VAC ROUND - V1.1_ES - www.idled.eu Reservado el derecho de realizar modificaciones sin previo aviso.

PRODUCT DESCRIPTION

Available in 2700K-3000K-4000K-5000K

CRI > 80 (CRI90 available under request)

Ideal for new or existing luminaires

Efficiency > 120 lm/W

Colour tolerance 3 SDCM

Space-saving design

Life-time exceeds 40.000 hrs.

High lm/$ relation

Integral solutions, no drivers required

Direct voltage connection to 230Vac

Extremely flat profile < 10mm

87


MERAKI LED MODULES AC DIRECT 155/70MM 230 VAC ROUND(70-155MM)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS

Voltage 210-240 Vac / 50-60 Hz

Voltage 210-240 Vac / 50-60 Hz

THD < 20%

Power factor > 0.9

Typical CRI80 (CRI90 available under request)

Operating temperature between -30ºC and 45ºC

MERAKI ROUND 155AC

EN 61471:2008 group 1

Standard Tc 65ºC

LED viewing angle 120°

Weight 100 g

MOQ 100 units

Possible to integrate with LOGO Custom

Ø3

.20

MERAKI ROUND 70 AC

Ø10.50

148

0

7.5

R7

69

IMPROVING

Ø

0

20

4.

Ø7

6.10

1.60

1.60

50 (*) Medidas en mm

6.10

94.93

Ø8

SPECIFIC TECHNICAL DATA MERAKI ROUND 70 DIRECT AC CODE

CCT

QTY LED

CRI

P.F.

NOMINAL POWER TC=75ºC (mA)

STANDARD VOLTAGE (V)

THD (%)

NOMINAL POWER

LUMINOUS EFFICACY

TOTAL FLUX

PHOTOMETRIC CODE

31.13.AC.40.01 31.13.AC.40.02 31.13.AC.40.03 31.13.AC.40.04

2700K 3000K 4000K 5000K

24 24 24 24

>80 >80 >80 >80

>0.9 >0.9 >0.9 >0.9

39.08 39.08 39.08 39.08

220-240 220-240 220-240 220-240

<20% <20% <20% <20%

8.990 8.990 8.990 8.990

97.976 102.514 115.328 123.337

880.80 921.60 1036.80 1105.80

827.348 830.348 840.348 850.348

DATOS TÉCNICOS ESPECÍFICOS MERAKI ROUND 155 DIRECT AC CODE

31.13.AC.155.01 31.13.AC.155.02 31.13.AC.155.03 31.13.AC.155.04

CCT

QTY LED

CRI

P.F.

NOMINAL POWER TC=75ºC (mA)

STANDARD VOLTAGE (V)

THD (%)

NOMINAL POWER

LUMINOUS EFFICACY

TOTAL FLUX

PHOTOMETRIC CODE

2700K 3000K 4000K 5000K

48 48 48 48

>80 >80 >80 >80

>0.9 >0.9 >0.9 >0.9

400 400 400 400

220-240 220-240 220-240 220-240

<20% <20% <20% <20%

17.500 17.500 17.500 17.500

100.663 105.326 118.491 126.720

1761.60 1843.20 2073.60 2217.60

827.348 830.348 840.348 850.348

(*) Optical and electrical measurements with tolerance +/- 10%. (**) For higher flows (500mA) it is necessary to maintain the Tc <65ºC by means of heatsink (not supplied).

MERAKI AC DORECT 155/70MM 230VAC ROUND - V1.1_ES - www.idled.eu Reservado el derecho de realizar modificaciones sin previo aviso.

88


MERAKI LED MODULES IMPROVING

AC DIRECT 155/70MM 230 VAC ROUND(70-155MM)

TECHNOLOGY

CONNECTION EXAMPLE

Recomendación para conexión sobre PCB Cable a utilizar: ≤ 0,5 mm² (flexible) / ≤ 0,75 mm² (rígido)

210-240 Vac 50/60 Hz

N L

ME R AK IR

O

D UN

AC

Reccommendation over PCB wire connection: ≤ 0,5 mm² (strand) / ≤ 0,75 mm² (solid)

230 Vcc 50/60 Hz

N L

ME R AK

N OU IR

D AC MERAKI AC DORECT 155/70MM 230VAC ROUND - V1.1_ES - www.idled.eu Reservado el derecho de realizar modificaciones sin previo aviso.

89


MERAKI LED MODULES IMPROVING

AC DIRECT 155/70MM 230 VAC ROUND(70-155MM)

TECHNOLOGY

INSTALLATION AND CONNECTION EXAMPLE

1

2

Dismantle profile base.

For eventual attachment of the fixture (with no use of double sided adhesive tape) drill a hole in the profile.

3

4 L

N

Place the PCB and apply pressure. Fix the screws to the

Introduce L and N wires in the pre-made holes, and connect

fixture base. (*)Accessory: M3 screws.

them to appropriate voltage.

5 Debe estar aislada para evitar el contacto con partes activas.

PCB instalada. MERAKI AC DORECT 155/70MM 230VAC ROUND - V1.1_ES - www.idled.eu Reservado el derecho de realizar modificaciones sin previo aviso.

90


MERAKI LED MODULES IMPROVING

TECHNOLOGY

AC DIRECT 155/70MM 230 VAC ROUND(70-155MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER MERAKI ROUND 155-70 AC DIRECT must be feed at constant and steady current of 210-240 Vac and 50-60 Hz. MERAKI AC DIRECT series from MERAKI family do not have polarity, this is due to the nature of its electrical power supply. For this reason all its parameters in this data sheet specified and rated current and nominal power must be respected and taken into account. If that is not the case, the module might be irreversibly damaged. MERAKI ROUND 155-70 AC DIRECT require specific protection against voltage picks or electrical network noise. ISOLATION MERAKI ROUND 155-70 AC DIRECT functions with greater voltage than SELV. Hence, it is required isolation with active components. It will be mandatory earth connection on all conductive components of the fixture or light engine. ESD – INFORMACIÓN SOBRE ESTÁTICA MERAKI ROUND 155-70 AC DIRECT contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI ROUND 155-70 AC DIRECT must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs and electronic components. The module will be delivered with 5 pre-made fastening holes: 4 through holes of D=5MM and 1 central hole of D=10MM. Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress on the PCB. Always avoid mechanical stress, compression stress or superficial voltage stress over the electronic components and/or driver holder. It is recommended to use nylon screws or similar to increase isolation with active components. Ideal wire for this connection type is unipolar solid wire of 0,4-1mm², with a strip wire of 6,5-7MM. To remove wire, push orifice on the connector and pull smoothly. TEMPERATURA MERAKI ROUND 155-70 AC DIRECT life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=70°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%. OPTICAL CHARACTERISTICS + CCT Measurement of LED discrete points may have variations in regards on the CCT temperature here described, with a variance of 3SDCM and 2SDCM for white and +/- 5nm for coloured LEDs. CCT shifts +/- 0,001 at 6.000 hrs. 3 SDCM are declared over the complete module. Modules viewing angle is 120°.

MERAKI AC DORECT 155/70MM 230VAC ROUND - V1.1_ES - www.idled.eu Reservado el derecho de realizar modificaciones sin previo aviso.

91


MERAKI FLEX IMPROVING

TECHNOLOGY

MODULE 24V RGB 120 (5000X10MM)

MERAKI family introduces flexible LED strips RGB MERAKI FLEX CV RGB 120. Module’s colour reproduction consistency and LEDs distance in a relation of 120 LED/m makes it an outstanding product for indirect architectural lighting, as pubs, restaurants or areas where environmental colours play a central role. They are designed to be feed at constant current of 24V. High final performance with linear small-sized fixtures, light homogeneity and short distance to diffuser. Great length flexibility, with a minimum of 5cm for unthinkable corners.

lm/$

>100 lm/w

3Years

Guarantee

In compliance with IEC 62031 / IEC 62471 / IEC 62717

APPLICATION

MERAKI FLEX MODULE 24V RGB 120 - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

PRODUCT DESCRIPTION

Efficiency > 100lm/W

Connection through solded wires in module

Easy installation

Including additional flex PCB connectors

High colour homogeneity

Compact design 12mm-wide

Minimum length 50mm

SELV voltage – 24V

92


MERAKI FLEX IMPROVING

MODULE 24V RGB 120 (5000X10MM)

TECHNOLOGY TECHNICAL DATA

SELV voltage

Available with 120 LED/m

50 mm length (6 LED)

Operating temperature between

DIMENSIONS 200

5000 tc ºC

8.33

EN 61471:2008 group 1

Standard Tc 75°C

Viewing LED angle 120°

Weight 60 g

MOQ 5 metres (reel)

Packaging box weight (approx.) 700 g (10 reels)

PWM dimmable

3

0.20

-20ºC and +45°C

SPECIFIC TECHNICAL DATA CODE

QTY LED

RATED CURRENT Tc= 75ºC (mA)

31.13.F2835A60QL/UL-2700K-90-24C

120

1200

STANDARD AVERAGE VOLTAGE CURRENT (V) (A)

24

1,2

NOMINAL POWER (W)

28,90

COLOUR STANDARD SPEC. (Nm) FLUX (lm)* RED GREEN BLUE

310 760 210

620-630 510-525 455-470

(*) All values are calculated on linear meters. (**) Always heatsink the flexible strip over aluminum to keep temperature < 75ºC over Tc.

CONNECTION EXAMPLE

RGB FLEXIBLE STRIP +24 -G -R -B

+24 = 24 Vcc constant voltage

* Connection to common cathode driver. * Do not connect more than 5 metres in series.

-G = Green color negative -R = Red color negative -B = Blue color negative For cutting LED strip:

50mm

* Each reel contains 3 additional connectors.

Línea de corte

MERAKI FLEX MODULE 24V RGB 120 - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

93


MERAKI FLEX IMPROVING

MODULE 24V RGB 120 (5000X10MM)

TECHNOLOGY

INSTALLATION AND CONNECTION EXAMPLE RGB LED strip

1

2

* 3M Double sided adhesive tape. Remove tape film.

Clean heatsink surface.

(*) ESD protection to earth connection.

3

*

It is very important to keep a clear and neat surface on the aluminum heatsink.

Stick LED strip on the aluminum heatsink carefully. (*) ESD protection to earth connection.

MERAKI FLEX MODULE 24V RGB 120 - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

94


MERAKI FLEX IMPROVING

TECHNOLOGY

MODULE 24V RGB 120 (5000X10MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER MERAKI FLEX CV RGB 120 must be feed at constant and steady current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules) connected in parallel. Family MERAKI LED MODULES have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the LED module might be irreversibly damaged. . MERAKI LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION MERAKI FLEX CV RGB 120 functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION MERAKI FLEX CV RGB 120 contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI FLEX CV RGB 120 must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source respecting its nominal values. This modules are designed to be introduced inside luminaries capable to dispel the heat generated by the module. PBS must be introduced carefully inside the system or luminary. Always avoid compression stress or superficial voltage stress over the electrical components. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs. Ideal wire for this connection type is multipolar flexible wire of 0,2-0,75 mm²; or use the provided 4 poles connectors to continue with an additional supply lines for the flexible strip up to 4 modules following each other. Do not attach more than 5 m in series. TEMPERATURE MERAKI FLEX CV RGB 120 life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=75°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%.

MERAKI FLEX MODULE 24V RGB 120 - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

95


MERAKI FLEX IMPROVING

TECHNOLOGY

MODULE 24V WHITE 60-120 (5000X10MM)

MERAKI family introduces flexible LED strips MERAKI FLEX CV 60/120 in WHITE. They are designed to be feed at constant voltage of 24V.

Module’s colour reproduction consistency

and LEDs distance in a relation of 60-120 LED/m makes it an outstanding product for direct and indirect lighting, as pubs, restaurants, offices or similar. High final performance with linear small-sized fixtures, light homogeneity and short distance to diffuser. Great length flexibility, with a minimum of 5cm for unthinkable corners. The module has integrated a driver for current control that contributes to guarantee homogeneous intensity and improves lifetime.

lm/$

>100 lm/w

3Years

Guarantee

In compliance with IEC 62031 / IEC 62471 / IEC 62717

APPLICATION

MERAKI FLEX MODULE 24V WHITE 60-120- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

PRODUCT DESCRIPTION

Efficiency > 100lm/W (white colour)

Connection through solded wires in module

Easy installation

Including additional flex PCB connectors

High colour homogeneity 3 SDCM

Compact design 12mm-wide

50 mm min. length

SELV voltage – 24V

96


MERAKI FLEX IMPROVING

TECHNOLOGY

MODULE 24V WHITE 60-120 (5000X10MM)

TECHNICAL DATA

DIMENSIONS

SELV voltage

Available with 60-120 LED/m

Min. length 50 mm (6 LED)

Operating temperature between -20ºC

5000

150

0.20

1

EN 61471:2008 group 1

Standard Tc 75°C

LED viewing angle 120°

Weight 60 g

MOQ 5 metres (reel)

Packaging box weight (approx.)

5000

150

1

15.60

700 g (10 reels) PWM dimmable

tc ºC * 60 LED model

0.20

SPECIFIC TECHNICAL DATA IP

QTY LED

CRI STANDARD AVERAGE NOMINAL EFFICIENCIES TYPE VOLTAGE CURRENT POWER (lm/W) (V) (A) (W)

31.13.FW120.02.24 2700K 31.13.FW120.03.24 3000K 31.13.FW120.04.24 4000K

IP20 indoor IP20 indoor IP20 indoor

120 120 120

>92 >92 >92

24 24 24

0,95 0,95 0,95

22,80 22,80 22,80

31.13.FW60.02.24 31.13.FW60.03.24 31.13.FW60.04.24

IP20 indoor IP20 indoor IP20 indoor

60 60 60

>92 >92 >92

24 24 24

0,475 0,475 0,475

11,40 11,40 11,40

CODE

* 120 LED model

7.80

and +45°C

tc ºC

CCT

2700K 3000K 4000K

STANDARD FLUX (lm)*

LED STANDARD FLUX (lm)*

81,05 94,63 102,79

1848 2157,6 2343,6

15,4 17,98 19,53

81,05 94,63 102,79

924 1078,8 1171,8

15,4 17,98 19,53

(*) All values are calculated on linear meters. (**) For 120 LED/m model it is required to dispel heat appropriately to keep Tc < 75ºC. (***) Flux measure tolerance of +/-7% with Tc < 65ºC.

CONNECTION EXAMPLE

RGB FLEXIBLE STRIP 24 Vcc (+/- 2V)

+ -

+ = Positive - = Negative

* Connection to common cathode driver. * Do not connect more than 5 m. in series

For cutting LED strip:

50mm * Each reel contains 3 additional connectors

Línea de corte MERAKI FLEX MODULE 24V WHITE 60-120- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

97


MERAKI FLEX IMPROVING

MODULE 24V WHITE 60-120 (5000X10MM)

TECHNOLOGY

INSTALLATION AND CONNECTION EXAMPLE RGB LED strip

1

2

* 3M Double sided adhesive tape Remove tape film

Clean heatsink surface.

(*) ESD protection to earth connection.

3

*

It is very important to keep a clear and neat surface on the aluminum heatsink.

Stick LED strip on the aluminum heatsink carefully (*) ESD protection to earth connection.

MERAKI FLEX MODULE 24V WHITE 60-120- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

98


MERAKI FLEX IMPROVING

TECHNOLOGY

MODULE 24V WHITE 60-120 (5000X10MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER MERAKI FLEX CV 60/120 must be feed at constant and steady current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules) connected in parallel. Family MERAKI LED MODULES have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the LED module might be irreversibly damaged. . MERAKI LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION MERAKI FLEX CV 60/120 functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION MERAKI FLEX CV 60/120 contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI FLEX CV 60/120 must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source respecting its nominal values. This modules are designed to be introduced inside luminaries capable to dispel the heat generated by the module. PBS must be introduced carefully inside the system or luminary. Always avoid compression stress or superficial voltage stress over the electrical components. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs. Ideal wire for this connection type is bipolar flexible wire of 0,2-0,75 mm²; or use the provided 2 poles connectors to continue with an additional supply lines for the flexible strip up to 4 modules following each other. Do not attach more than 5 m in series. TEMPERATURE MERAKI FLEX CV 60/120 life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=75°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%.

MERAKI FLEX MODULE 24V WHITE 60-120- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

99


MERAKI LED MODULES IMPROVING

TECHNOLOGY

MF CC D=20MM 3W 3535 (D=20MM)

This module of 20MM diameter and 1-3W LED from MERAKI ECO family is ideal for applications such as spotlights, reading lights, courtesy light or signage. MERAKI CIRCULAR CC D=20MM 3W 3535 are designed to be feed at constant current. The module is an attractive item, due to its small size and low unit price. The product holds solded wires used for connection. Efficiencies are determined by the chosen operating current. This module works perfectly together with the Drivers Dunamic STEP DOWN in CC, as BUCK DRIVERS..

lm/$

>120 lm/w

5Years

Guarantee

In compliance with IEC 62031 / IEC 62471 / IEC 62717

APPLICATION

MERAKI MF CC D=20MM 3W 3535 - V1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

PRODUCT DESCRIPTION

ECO module 1-3W in CC.

Efficiency > 120 lm/W

Connection through welded wires in module

Available with 250 mm wire

CCT tolerance -3 SDCM

Available in 2700-3000-4000-5000K

Compact design

SELV voltage

5 years guarantee

Ideal for reading lights, courtesy lights, etc.

100


MERAKI LED MODULES MF CC D=20MM 3W 3535 (D=20MM)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS

SELV voltage Vin=2,94 - 3,1V

Operating temperature between -5ºC and +50ºC

Weight 5 grs

MOQ: 108 units

Dimensions: 19,4x14,8x4mm

Imax=1,4 A // Tc=75ºC (heatsink required)

Excluding reverse polarity protection

Max. driver length 5 m.

For fixtures integration, CE directives compliance.

IEC 62471 risk group: 0

ESD 5 KV protection

Maximum of 5 units per serie

(*) Measured in mm

3.70

14.80

19.40

1.60

IMPROVING

SPECIFIC TECHNICAL DATA CODE

CCT

QTY LED

CRI typ.

RATED CURRENT Tc=65ºC (mA)

MIN. VOLTAGE (V)

AVERAGE NOMINAL EFFICIENCIES STANDARD (lm / W) FLUX CURRENT POWER (Im)(*) (W) (A)

31.13.0075 31.13.0076 31.13.0077 31.13.0078

2700 K 3000 K 4000 K 5000 K

1 1 1 1

>80 >80 >80 >80

350 500 700 1000

2,94 2,94 2,94 2,94

0,352 0,352 0,352 0,352

1,035 1,035 1,035 1,035

108,071 109,017 116,989 122,004

111,84 112,82 121,07 126,26

827.348 827.348 827.348 827.348

31.13.0075 31.13.0076 31.13.0077 31.13.0078

2700 K 3000 K 4000 K 5000 K

1 1 1 1

>80 >80 >80 >80

350 500 700 1000

2,98 2,98 2,98 2,98

0,502 0,502 0,502 0,502

1,496 1,496 1,496 1,496

103,512 100,120 111,664 117,015

154,85 149,78 167,05 175,05

830.348 830.348 830.348 830.348

31.13.0075 31.13.0076 31.13.0077 31.13.0078

2700 K 3000 K 4000 K 5000 K

1 1 1 1

>80 >80 >80 >80

>80 >80 >80 >80

3,01 3,01 3,01 3,02

0,702 0,702 0,702 0,702

2,113 2,113 2,113 2,120

97,006 98,591 104,649 108,253

204,98 208,33 221,13 229,50

840.348 840.348 840.348 840.348

31.13.0075 31.13.0076 31.13.0077 31.13.0078

2700 K 3000 K 4000 K 5000 K

1 1 1 1

>80 >80 >80 >80

>80 >80 >80 >80

3,07 3,07 3,07 3,07

1,001 1,001 1,001 1,001

3,073 3,073 3,073 3,073

86,762 91,264 94,677 97,964

266,63 280,46 290,95 301,05

850.348 850.348 850.348 850.348

PHOTO METRIC CODE

(**) It is required to keep Tc < 65ºC. (***) For PCB supply including high adhesion thermal tape, please add the letter “C” behind the product code. Example: 31.13.0075C.

CONNECTION EXAMPLE VinV 12 Vcc

+

-

VinV

b.

12 Vcc

V: 5,84

d Ad

ition

al heats ink

r

ired

+

u eq

a.

out

out

+

+

-

-

MERAKI MF CC D=20MM 3W 3535 - V1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

V: 2,94

101


MERAKI LED MODULES IMPROVING

MF CC D=20MM 3W 3535 (D=20MM)

TECHNOLOGY

EJEMPLO DE INSTALACIÓN Y CONEXIÓN

1

2

FA

2,8V

24Vcc

Connect DC/DC to LED.

Connect to input voltage.

3

4

A FA

Introduce module in the fixture.

Close the module.

Lifetime Derating for MERAKI CIRCULAR CC D20MM 110.000 100.000 Lifetime ( L80 / B50) h

90.000 80.000 70.000 60.000 50.000 40.000

700 mA (> 48.000 hs)

30.000

350 mA (> 50.000 hs)

20.000 10.000 0 20

30

40

50 60 70 Temperature Tc (°C)

MERAKI MF CC D=20MM 3W 3535 - V1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

80

90

100

102


MERAKI LED MODULES IMPROVING

TECHNOLOGY

MF CC D=20MM 3W 3535 (D=20MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER MERAKI CIRCULAR CC D=20MM 3W 3535 must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). Family MERAKI LED MODULES have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. MERAKI LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION MERAKI CIRCULAR CC D=20MM 3W 3535 functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION MERAKI CIRCULAR CC D=20MM 3W 3535 contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI CIRCULAR CC D=20MM 3W 3535 must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source. Thermal transference between PCB and luminaire body must be at its highest, in order to ensure that fixture temperature does not exceed Tc in any case. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs. The module will be delivered with 2 pre-made holes of D=3,2 mm, according to dimensions drawing. Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress. The module includes connection wire(s). TEMPERATURE To ensure MERAKI CIRCULAR CC D=20MM 3W 3535 life-time and guarantee, room temperature must be checked under worst-case conditions. Its mechanical and electrical optimal properties depend on temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=75°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Store modules in between -20 °C and +80 °C and maximum humidity level of 65%. OPTICAL CHARACTERISTICS + CCT Discrete measurement of LED, may vary in regards on the CCT temperature here described, with a variance of 3SDCM for white and +/- 5nm for coloured LEDs. CCT shifts +/- 0,001 at 6.000 hrs. 3 SDCM are declared over the complete module. Modules viewing angle is 120°.

MERAKI MF CC D=20MM 3W 3535 - V1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

103


MERAKI LED MODULES IMPROVING

TECHNOLOGY

MERAKI RGB RIGID LINEAR CV 24 V 282-702 (70-282X24MM)

MERAKI family introduces the new RGB 282-702 24V modules. They are designed to be feed at constant voltage of 24V. Module’s colour reproduction consistency and LEDs distance in a relation of 80 LED/m makes it an outstanding architectural lighting product for direct and indirect lighting as pubs, restaurants, or areas where environmental colours play a central role. High final performance with linear small-sized fixtures, light homogeneity and short distance to diffuser. Great length flexibility, with a minimum of 70mm for unthinkable corners. Module’s dimensions are ZHAGA format compatible and a fitting partner for transforming monochromatic linear luminaires to RGB.

lm/$

>110 lm/w

2Years

Guarantee

In compliance with IEC 62031 / IEC 62471 / IEC 62717

APPLICATION

MERAKIRGB RIGID LINEAR CV 24V 282-702 - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

PRODUCT DESCRIPTION

Efficiency > 110lm/W

Push-In connector type

Easy installation

ZHAGA compatible

High colour homogeneity

Compact design 24mm wide

Minimum length 70mm

SELV voltage – 24V

104


MERAKI LED MODULES MERAKI RGB RIGID LINEAR CV 24 V 282-702 (70-282X24MM)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS

SELV voltage

Available with 800 LED/m

Operating temperature between -20ºC and +45°C

EN 61471:2008 group 1

Standard Tc 75°C

17 33.40

Viewing LED angle 120°

Weight 60 g

MOQ 44 units

Packaging box weight (approx.) 2640 gr

PWM dimmable

1.60

22.9

17.2

50.60

4.25

IMPROVING

(*) Measured in mm

280 250

24

18

125

216.1

4.25

1.60

251.6

SPECIFIC TECHNICAL DATA CODE

QTY LED

RATED CURRENT Tc=65ºC (mA)

STANDARD VOLTAGE (V)

AVERAGE VOLTAGE (A)

NOMINAL POWER (W)

COLOUR

STANDARD FLUX (Im)*

SPECTRUM (Im)*

31.13.282.24C.RGB

24

240

24

0,240

5,76

RED GREEN BLUE

620-630 510-525 455-470

1,56

RED GREEN BLUE

62.4 126.5 31.68 T: 220.58 62.4 126.5 31.68 T: 220.58

31.13.702.24C.RGB

6

60

24

0,065

620-630 510-525 455-470

(*) Tolerance range for flux measurements of 8%. (**) It is required to keep Tc < 65ºC. (***) For PCB supply including high adhesion thermal tape, please add the letter “C” behind the product code. Example: 31.13.702.24C.RGBC.

DRIVER + MODULE CONNECTION EXAMPLE

G R B +

+24 = 24 Vcc constant voltage -G = Green color negative -R = Red color negative

G R B +

-B = Blue color negative

MERAKIRGB RIGID LINEAR CV 24V 282-702 - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

105


MERAKI LED MODULES IMPROVING

MERAKI RGB RIGID LINEAR CV 24 V 282-702 (70-282X24MM)

TECHNOLOGY

Recommendation over PCB wire connection:

230 Vac 50/60 Hz

≤ 0,5 mm² (strand) / ≤ 0,75 mm² (solid)

L N

IN

DRIVER RGB

OUT

+24 -G -R -B

INSTALLATION AND CONNECTION EXAMPLE

2

1

*

For eventual attachment of the fixture (with no use of double

Place the PCB and apply pressure. Fix the screws to the

sided adhesive tape) drill a hole in the profile.

fixture base. Accessory: M3 screws. (*) ESD protection to earth connection.

Co

nn

e

3

es with each dul oth o m er t c

MERAKIRGB RIGID LINEAR CV 24V 282-702 - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

Max. no. of PCBs: Depends on driver type Vf total PCBs ≤ Vout Driver

106


MERAKI LED MODULES IMPROVING

TECHNOLOGY

MERAKI RGB RIGID LINEAR CV 24 V 282-702 (70-282X24MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER MERAKI RGB 282-702 24V must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). Family MERAKI have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. MERAKI LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION MERAKI RGB 282-702 24V functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION MERAKI RGB 282-702 24V contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI RGB 282-702 24V must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source, respecting its nominal values. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs and electronic components. MERAKI RGB 282-702 24V modules are designed to be incorporated inside linear light fixtures, capable to dispel the heat generated by the module. PCB must be introduced carefully inside the system or luminary. Always avoid mechanical stress, compression stress or superficial voltage stress over the electronic components of the PCB. The module will be delivered with 4 pre-made holes of D=4,5 mm, according to dimensions drawing (ZHAGA L2W6). Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress. Ideal wire for this connection type is multipolar strand wire of 0,2-0,75mm². Do not attach more than 3m in series. TEMPERATURE MERAKI RGB 282-702 24V life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=75°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%.

MERAKIRGB RIGID LINEAR CV 24V 282-702 - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

107


MERAKI LED MODULES IMPROVING

TECHNOLOGY

FINGUERS CC SQUARE (145X249MM)

RECTANGULAR MERAKI CC MF are ideal to complete round or square designed light fixtures that require high efficiency and flexibility. These LED modules are capable to replace fluorescence downlights of 2x26W with no need to replace the whole fixture, meaning direct cost saving. At nominal power they do not need heatsinks. As a result of its easy installation and performance, is a perfect partner for professionals in light fixtures production. RECTANGULAR MERAKI CC MF modules are excellent items for development of light fixtures and cost saving (vs. former technologies). Constant voltage versions offer total flexibility.

lm/$

>175 lm/w

5Years

Guarantee

In compliance with IEC 62031 / IEC 62471 / IEC 62717

PRODUCT DESCRIPTION

APPLICATION

MERAKI LED FINGUERS CC SQUARE - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

ZHAGA standard BOOK 7

Luminous flux 900 lm

High efficiency module >120lm/W

Colour temperature 300K/4000K/5000K

Colour variation 2SDCM

Operating temperature between -30ºC and +40ºC

Luminous maintenance L70/B50 36.000 hours

Flux and colour uniformity between modules

Easy to install (with screws)

Optional: double sided adhesive thermal tape

Quick connectors (wires up to 1mm2)

Reverse polarity protection

5 years guarantee

108


MERAKI LED MODULES IMPROVING

FINGUERS CC SQUARE (145X249MM)

TECHNOLOGY

DIMENSIONS 3.50

TECHNICAL DATA

SELV voltage

Available in 2700K-3000K-4000K-5000K

Typical CRI80 (CRI90 available under request)

Operating temperature between -30ºC and + 45º C

EN 61471:2008 group 1

Standard Tc 65ºC

LED viewing angle 120°

Weight 60 g

MOQ 32 unit

Possible to integrate with LOGO Custom

20 25

245

Ø3.20

25

248.75 (*) Measured in mm

SPECIFIC TECHNICAL DATA CODE

CCT

ELECTRICAL RATED CURRENT POWER Tc=65ºC (VCC) (mA)

MAX. VOLTAGE Tc: 65°C (V) (*)

NOMINAL POWER (W)

STANDARD FLUX (Im)(*)

EFFICACY (lm / W)

CRI typ.

QTY LED

PHOTO METRIC CODE

Without heatsink

31.13.05102 31.13.05103 31.13.05104 31.13.05105

2700k 3000k 4000k 5000k

33,6-36 33,6-36 33,6-36 33,6-36

350 350 350 350

35,00 35,15 35,50 35,50

12,25 12,3 12,43 12,43

1704 1752 1780 1831

139,11 142,43 143,2 147,3

> 82 > 82 > 82 > 82

48 48 48 48

827.348 830.348 840.348 850.348

With heatsink (**)

31.13.05102 31.13.05103 31.13.05104 31.13.05105

2700k 3000k 4000k 5000k

33,6-36 33,6-36 33,6-36 33,6-36

500 500 500 500

35,90 35,40 35,90 35,50

17,95 17,7 17,95 17,75

2188 2221 2299 2376

121,9 125,48 128,01 134,18

> 82 > 82 > 82 > 82

48 48 48 48

827.348 830.348 840.348 850.348

(*) Optical and electric measures with tolerance of +/- 10%. (**) For higher fluxes (500mA) is required to keep Tc < 65ºC, with heatsink (not included).

DRIVER + MODULE CONNECTION EXAMPLE

230 Vcc 50/60 Hz

L

N DRIVER 500mA

MERAKI LED FINGUERS CC SQUARE - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

+ -

109


MERAKI LED MODULES IMPROVING

FINGUERS CC SQUARE (145X249MM)

TECHNOLOGY

INSTALLATION AND CONNECTION EXAMPLE

1

2

For eventual attachment of the fixture (with no use of double

Dismantle profile base.

sided adhesive tape) drill a hole in the profile.

3

4 -

+

. Place the PCB and apply pressure. Fix the screws to the

Introduce the positive (+, red) and negative (-, black) wires in

fixture base. (*) Accessory: M3 screws.

the pre-made holes, and connect them to appropriate voltage.

5

PCB is utterly installed. MERAKI LED FINGUERS CC SQUARE - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

110


MERAKI LED MODULES IMPROVING

FINGUERS CC SQUARE (145X249MM)

TECHNOLOGY

Lifetime Derating for MERAKI CIRCULAR CC - MEDIUM FLUX

110.000 100.000 Lifetime ( L80 / B50) h

90.000 80.000 70.000 60.000 50.000 40.000

500 mA (> 48.000 hs)

30.000

350 mA (> 50.000 hs)

20.000 10.000 0 20

30

40

50 60 70 Temperature Tc (°C)

MERAKI LED FINGUERS CC SQUARE - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

80

90

100

111


MERAKI LED MODULES IMPROVING

TECHNOLOGY

FINGUERS CC SQUARE (145X249MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER RECTANGULAR MERAKI FINGERS must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). Family merakihave polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. MERAKI LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION RECTANGULAR MERAKI FINGERS functions with SELV voltage, does not require active isolation of the component as long as maximum reference (50v) SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION RECTANGULAR MERAKI FINGERS contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. RECTANGULAR MERAKI FINGERS must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source, respecting its nominal values. I+D LED S.L. is not responsible for occasional module fall. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs and electronic components. The module will be delivered with 5 pre-made holes; 4 of D=5 mm and 1 central hole of D=10mm. Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress. Ideal wire for this connection type is unipolar rigid wire of 0,4-1mm², with a strip wire of 6,5-7MM. To remove wire, push orifice on the connector and pull smoothly. TEMPERATURE RECTANGULAR MERAKI FINGERS life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=85°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%. OPTICAL CHARACTERISTICS + CCT Measurement of LED discrete points may have variations in regards on the CCT temperature here described, with a variance of 3SDCM for white and +/- 5nm for coloured LEDs. CCT shifts +/- 0,001 at 6.000 hrs. 3 SDCM are declared over the complete module. Modules viewing angle is 120°.

MERAKI LED FINGUERS CC SQUARE - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

112


DUNAMIC LED DRIVERS DUNAMIC family has AC/DC and DC/DC Buck/Boost LED DRIVERS suitable for any LED lighthing application, from small size fixtures with low cost solution, to high-end products. This Family gives you miniaturized luminaries designs using smaller tracks and low voltage. These products are easy to use, they increase efficiency and decrease costs. Soft starts, international regulations compliance, failure rates <10% for 40.000 hrs, wide dimming range and SELV voltages are some hot spots of our products. Best compromise between quality and attractive prices are guaranteed. ODM, custom products and OEM solutions have never been so easy with our flexible policy. Track lights _dcdc custom inside spots

DC DRIVERS

Dunamic drivers 3W Tiny

AC DRIVERS

Avalaible in diferent sizes

Long lifetime >40.000 hrs.

SELV voltage drivers

High efficiency

Easy thermal management

Simple installation

Fast Push-in type connectors

Active PFC function

Low cost and low energy consumption

Suitable for indoor use

100% full load test

Short circuit/ overload/ over voltage/ overheat protection

2-4 years limited warranty

Track lights _ dcdc custom inside spots 113


DC DRIVERS IMPROVING

TECHNOLOGY

DUNAMIC STEP - DOWN ECO DRIVER 12-24 CVV (55X12MM)

STEP-DOWN ECO 12-24V from DUNAMIC family is a DC/ DC step-down driver with constant voltage input 12-24V and constant current output, serves ideally for spotlights or LED modules. Due to its small size and low unit price, the driver is an attractive item that fits in small size fixtures where unit price plays a central role. The driver includes quick Push-In connectors to facilitate IN/OUT connection. These drivers are the ideal complement to work side by side with MERAKI LED MODULES family in CC.

3Years

Guarantee

In compliance with EN62384:2007/A1:2010 - EN61547:2013 EN61347 - 1:2009/A1:2013

APPLICATION

DUNAMIC STEP - DOWN ECO DRIVER 12-24 VCC - V1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

PRODUCT DESCRIPTION

Driver DC/DC ECO

Current 200/350/400/500/600/700 mA

Quick Push-In connectors

Up to 17W in output

Compact design

SELV voltage

3 years guarantee

Ideal for versions in CC

114


DC DRIVERS DUNAMIC STEP - DOWN ECO DRIVER 12-24 CVV (55X12MM)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS 55

SELV voltage Vin=12-24 V

Operating Temperature between -5ºC and + 45ºC

Vout max= 21V

Weight 5 g

MOQ: 56 units

Dimensions: 55x12x7mm

Open Frame (luminaries class I y II)

Pout max=17W

No short circuit protection

No overload protection

Max. length STEP/LED L:10m

For fixtures integration, CE directives compliance

6.64

1.60

12

6.10

IMPROVING

(*) Measured in mm

SPECIFIC TECHNICAL DATA CODE

RATED CURRENT (mA)

VOLTAGE RANGE Vin

NOMINAL VOLTAGE Vin

MAX. LED NO.

RIPPLE (MAX. CARGA)

VOLTAGE RANGE OUTPUT Vout

SWITCHING FREQUENCY

EFFICIENCY (%)

31.60.016 31.60.017 31.60.018 31.60.019 31.60.020 31.60.021

200mA 350mA 400mA 500mA 600mA 700mA

12-24 V 12-24 V 12-24 V 12-24 V 12-24 V 12-24 V

12V 12V 12V 12V 12V 12V

3 3 3 3 3 3

0,09 0,095 0,12 0,135 0,165 0,14

9-21V 9-21V 9-21V 9-21V 9-21V 12-21V

150Khz - 550 Khz 150Khz - 550 Khz 150Khz - 550 Khz 150Khz - 550 Khz 150Khz - 550 Khz 150Khz - 550 Khz

84,37 88,33 88,038 86,57 85,52 84,05

31.60.016 31.60.017 31.60.018 31.60.019 31.60.020 31.60.021

200mA 350mA 400mA 500mA 600mA 700mA

21-24 V 21-24 V 21-24 V 21-24 V 21-24 V 21-24 V

24V 24V 24V 24V 24V 24V

6 6 6 6 6 6

0,12 0,12 0,135 0,12 0,14 0,16

9-21V 9-21V 9-21V 9-21V 9-21V 12-21V

150Khz - 550 Khz 150Khz - 550 Khz 150Khz - 550 Khz 150Khz - 550 Khz 150Khz - 550 Khz 150Khz - 550 Khz

86,72 89,46 89,77 90,55 90,148 89,852

(*) For silicone heat shrink tubing protection supply, please add the letter “T” behind the product code. Example: 31.60.0012T. (*) Tolerance range for measurements of 8%. (*) Vout=Vin-3v. (*) Values obtained at temperature 30ºC. (*) If module is connected to a higher power than indicated in output, current will drop drastically and lose stability.

EFFICIENCY (%) VS Nº OF LEDS

EFFICIENCY (%) VS Nº OF LEDS v(Vin = +12Vdc, Vf led = 3V)

(Vin = +24Vdc, Vf led = 3V) 100

100

90

90

80

80 70

200mA

60

350mA

50

400mA

Efficiency (%)

Efficiency (%)

70

200mA

60

350mA

50

400mA

40

500mA

600mA

30

600mA

700mA

20

700mA

40

500mA

30 20

10

10

0

0 1

2

3

4

5

6

Number of leds

DUNAMIC STEP - DOWN ECO DRIVER 12-24 VCC - V1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

1

2 Number of leds

3

115


DC DRIVERS IMPROVING

DUNAMIC STEP - DOWN ECO DRIVER 12-24 CVV (55X12MM)

TECHNOLOGY

EFFICIENCY (%) VS CURRENT (A) (Vin = +12Vdc, Vf led = 3V) 88,5 88 87,5

Efficiency ( %)

87 86,5 86

Data Input

85,5 85 84,5 84 0,2

0,35

0,4

0,5

0,6

0,7

Measured Current (A)

EFFICIENCY (%) VS CURRENT (A) (Vin = +24Vdc, Vf led = 3V) 91 90,5

Efficiency ( %)

90 89,5 89 88,5

Data Input

88 87,5 87 86,5

0,2

0,35

0,4

0,5

0,6

0,7

Measured Current (A)

CONNECTION EXAMPLE VinV

a.

12 Vcc

+

+

-

VinV

b.

12 Vcc

24 Vcc

+

-

-

d.

24Vcc

+

-

-

e.

24Vcc

+

-

-

V: 11,24

out

+

+

-

-

DUNAMIC STEP - DOWN ECO DRIVER 12-24 VCC - V1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

V: 8,44

out

+

VinV

V: 2,94

out

+

VinV

V: 5,84

out

+

VinV

c.

out

V: 14,6

116


DC DRIVERS IMPROVING

TECHNOLOGY

DUNAMIC STEP - DOWN ECO DRIVER 12-24 CVV (55X12MM) CONNECTION EXAMPLE

1

2

24

Vc c

2,8V

Connect DC/DC to LED.

3

Connect to input voltage. I.e. 24Vcc.

4

Introduce module in the fixture.

DUNAMIC STEP - DOWN ECO DRIVER 12-24 VCC - V1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

Close the module.

117


DC DRIVERS IMPROVING

TECHNOLOGY

DUNAMIC STEP - DOWN ECO DRIVER 12-24 CVV (55X12MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER STEP-DOWN ECO 12-24V must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). Family DUNAMIC LED DRIVERS have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. DUNAMIC LED MODULES require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION STEP-DOWN ECO 12-24V functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage is not exceeded and in other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION STEP-DOWN ECO 12-24V contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. STEP-DOWN ECO 12-24V must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source, respecting its nominal values. STEP-DOWN ECO 12-24V modules are designed to be incorporated inside small size light fixtures, as tubes or boxes greater than 56x13x8 mm. Always avoid mechanical stress, compression stress or superficial voltage stress over the electronic components of the PCB. Caution may be taken when placing the PCB inside the lighting fixture or system, as it has an open frame format; or version including silicone heat shrink tubing for protection can be requested. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs. The module is delivered no pre-made holes. Ideal wire for this connection type is multipolar flexible wire of 0,2-0,75mm². TEMPERATURE STEP-DOWN ECO 12-24V life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=80°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%.

DUNAMIC STEP - DOWN ECO DRIVER 12-24 VCC - V1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

Tc = 80°C

118


DUNAMIC LED DRIVERS IMPROVING

TECHNOLOGY

AC DRIVERS - TINY 3W 350/700MA (40X27.5X56MM)

I+D LED introduces new AC/DC drivers for tiny LED. Available in 300 and 700 mA in constant current output. Pre-wired drivers to facilitate mounting and installation and miniscule size to be hidden inside any small size fixture. Designed for LED power of 1-2.5W. Very attractive module for downlight spots, decorative illumination, furniture, exhibitors or similar where unit price plays a central role. Universal voltage input from 100-240Vac, for usage on different electrical voltages.

3Years

Guarantee

In compliance with EN 61347-2-13:2014/EN 61347-1:2015 EN 55015:2013+A1:2015/EN 61547:2009 EN 61000-4-2:2009/EN 61000-4-3:2006+A2:2010

APPLICATION

DUNAMIC AC DRIVERS - TINY 3W 350/700 MA - V1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

PRODUCT DESCRIPTION

AC/DC ECO driver

350/700mA current

Pre-wired

3 years guarantee

For power LED

Class type II, without connection

SELV voltage

Compact design

For fixtures integration

119


DUNAMIC LED DRIVERS IMPROVING

AC DRIVERS - TINY 3W 350/700MA (40X27.5X56MM)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS

Input range 100-240V

Tc = 80ºC

Class type II

FP > 0,5 full load

50-60 Hz

Power = 1-3W

For fixtures integration, CE directives compliance

Weight 5 g

Soft start

BOX dimensions = 39x26x21mm

Maximum driver lengt t 4 m

Operating temperature between -5ºC and +45ºC

40

D 3,7

10

27.50

tcºC

21.60

47.4

56 (*) Measured in mm

SPECIFIC TECHNICAL DATA CODE

INPUT VOLTAGE (V)

FREQUENCY (Hz)

COS FP (Phi)

OUTPUT VOLTAGE (V)

OUTPUT CURRENT (A)

NOMINAL POWER (W)

OUTPUT TOLERANCE (iout)

31.60.AC.100 31.60.AC.100

100 240

50 50

0,576 0,543

3,283 3,283

0,6755 0,6738

2,2176665 2,2120854

(+/-)5% (+/-)5%

31.60.AC.200 31.60.AC.200

100 240

50 50

0,533 0,526

3,033 3,033

0,3298 0,3295

1,0002834 0,9993735

(+/-)5% (+/-)5%

31.60.AC.200 31.60.AC.200

100 240

50 50

0,560 0,545

5,94 5,94

0,3288 0,3288

1,953072 1,953072

(+/-)5% (+/-)5%

31.60.AC.200 31.60.AC.200

100 240

50 50

0,625 0,512

8,88 8,88

0,327 0,327

2,90376 2,90376

(+/-)5% (+/-)5%

CONNECTION EXAMPLEN

VinV

out + -

V: 2,94

+

100

240 Vcc

-

Wire length 130 mm. Section: 0.5-0.75 m2.

DUNAMIC AC DRIVERS - TINY 3W 350/700 MA - V1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

Wire length 130 mm. Section: 0.5-0.75 m2.

120


DUNAMIC LED DRIVERS IMPROVING

AC DRIVERS - TINY 3W 350/700MA (40X27.5X56MM)

TECHNOLOGY

CONNECTION EXAMPLE

1

2

2,8V LED output

Output

Connect driver to sportlight.

3

Connect to power plug.

4

Introduce module in the fixture and close.

DUNAMIC AC DRIVERS - TINY 3W 350/700 MA - V1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

Connect fixture to voltage.

121


DUNAMIC LED DRIVERS IMPROVING

TECHNOLOGY

AC DRIVERS - TINY 3W 350/700MA (40X27.5X56MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER DUNAMIC DRIVERS AC/DC must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). Family have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. DUNAMIC DRIVERS AC/DC require specific protection against voltage picks or electrical network noice. ISOLATION DUNAMIC DRIVERS AC/DC functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD â&#x20AC;&#x201C; STATIC ELECTRICITY INFORMATION DUNAMIC DRIVERS AC/DC contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product DUNAMIC DRIVERS AC/DC must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source, respecting its nominal values DUNAMIC DRIVERS AC/DC are designed to be incorporated inside small size light fixtures, the driver has two flaps for this use. Always avoid mechanical stress, compression stress or superficial voltage stress over the electronic components and/or driver holder. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs and electronic components. The driver is delivered with a strip wire of 4-7mm (for board to board connectors or join by soft soldering). Total length of input and output wires is of L:130MM(*). TEMPERATURE DUNAMIC DRIVERS AC/DC life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=80°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to

(*) Wire maximum length and output polarity must be respected. I+D LED S.L. is not responsible for LEDs failure in case mounting and installation instructions are not properly followed.

DUNAMIC AC DRIVERS - TINY 3W 350/700 MA - V1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

122


DUNAMIC LED DRIVERS IMPROVING

TECHNOLOGY

AC DRIVERS - LC SERIES PF 8,4W 350/700MA_12V/24V (146,6X21X19MM)

I+D LED introduces the new AC/DC drivers for LED of the LINER LC series. These are available in 350 and 700 mA, in constant current output and optional operating voltage of 12v or 24V. Ideal for low cost solutions that seek active power factor (PF). With standard terminals connection. Their tiny size makes them a perfect suit for small size luminaries. Designed for LED power from 2 to 8W. Its low price makes this driver a very attractive item for downlights, decorative lighting, furniture, displays, spots or similar where the unitary cost plays a central role.

5Years

Guarantee

In compliance with EN 61347-2-13:2014/EN 61347-1:2015 EN 55015:2013+A1:2015/EN 61547:2009 EN 61000-4-2:2009/EN 61000-4-3:2006+A2:2010

APPLICATION

PRODUCT DESCRIPTION

AC/DC driver LC SERIES

Operating current from 350mA to 700mA

Output available in 12-24V

Screw terminals

3 years guarantee

For powerful LED

Class II, no earth connection

High PF

SELV voltage

Compact design

DUNAMIC AC DRIVERS - LC SERIES PF 8,4W 350/700 MA_ 12/24V - V1.1_ES www.idled.eu Reservado el derecho de realizar modificaciones sin previo aviso.

123


DUNAMIC LED DRIVERS IMPROVING

AC DRIVERS - LC SERIES PF 8,4W 350/700MA_12V/24V (146,6X21X19MM)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS

Input range 160V-240V / 50Hz

Max. output power 8W

Class II

Short circuit protection

FP > 0,9 at full load

350mA-700mA in CC // 12V-24V in CV

For fixtures integration, CE directives compliance

Weight 50g

Wire section up to 1mm2

Soft Start – Soft switch off

Dimensions box = 147x21x19 mm

Max. wire length to power source 3 m

Operating temperature between -5ºC and +50ºC

21

146.60

2

19

130

(*) Medidas en mm

SPECIFIC TECHNICAL DATA CODE

TYPE

INPUT VOLTAGE (V)

FRQUENCY (Hz)

COS(PHI) OUTPUT (FP) VOLTAGE (V)

31.60.AC.004.700 700mA 31.60.AC.004.700 12V

230 230

50 50

>0.859 >0.92

31.60.AC.004.350 350mA 31.60.AC.004.350 24V

230 230

50 50

>0.835 >0.91

OUTPUT CURRENT (A)

NOMINAL POWER (W)

OUTPUT TOLERANCE (Iout)

EFFICIENCY (%)

3...12 12

0.7 0.7

2...8.4 8.4

(+/-) 5% (+/-) 5%

75% 85%

6...24 24

0.35 0.35

2...8.4 8.4

(+/-) 5% (+/-) 5%

75% 85%

(*) 12 and 24v constant voltage versions (**) The values of efficiencies and PF are at full load 95-100%

CONNECTION EXAMPLE

100-240 Vac 31.60.AC.004.350 220-240 VAc 50/60 Hz Primary

Dunamic LED Driver

F

I Out: 0.35 A CC LED Driver P Out: 8.4 W Thermal Protection tc max: 85 ºC P.F.>0.9 TDH<35% ta max: -18~65 ºC

C

6-8 LEDs

Class II RoHS SELV

tc

-

-

+

+

Secondary 24Vdc-350mA

160-240 Vac 31.60.AC.004.350 220-240 VAc 50/60 Hz Primary

Dunamic LED Driver

F

I Out: 0.35 A CC LED Driver P Out: 8.4 W Thermal Protection tc max: 85 ºC P.F.>0.9 TDH<35% ta max: -18~65 ºC

C

Class II RoHS SELV

6-8 LEDs tc Secondary 24Vdc-350mA

+

+ Meraki 300x20

DUNAMIC AC DRIVERS - LC SERIES PF 8,4W 350/700 MA_ 12/24V - V1.1_ES www.idled.eu Reservado el derecho de realizar modificaciones sin previo aviso.

124


DUNAMIC LED DRIVERS IMPROVING

TECHNOLOGY

AC DRIVERS - LC SERIES PF 8,4W 350/700MA_12V/24V (146,6X21X19MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER DUNAMIC LED DRIVERS AC/DC must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules) connected in parallel. Family DUNAMIC have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. DUNAMIC DRIVERS AC/DC require specific protection against voltage picks or electrical network noise. ISOLATION DUNAMIC DRIVERS AC/DC functions with SELV voltage, it does not require active isolation of the component as long as maximum reference SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION DUNAMIC DRIVERS AC/DC contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. DUNAMIC DRIVERS AC/DC must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source, respecting its nominal values. DUNAMIC DRIVERS AC/DC are designed to be incorporated inside small size light fixtures, the driver has two flaps for this use. Always avoid mechanical stress, compression stress or superficial voltage stress over the electronic components and/or driver holder/protection box. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs and electronic components. The driver is delivered with 0.5-1.5mm² connection wires for screw connection terminals (included). TEMPERATURE DUNAMIC DRIVERS AC/DC life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=80°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity

DUNAMIC AC DRIVERS - LC SERIES PF 8,4W 350/700 MA_ 12/24V - V1.1_ES www.idled.eu Reservado el derecho de realizar modificaciones sin previo aviso.

125


DUNAMIC LED DRIVERS IMPROVING

TECHNOLOGY

AC DRIVERS - LC SERIES 8,4W 350/700 MA_ 12/24V (59X41X21.2)

I+D LED introduces the new AC/DC drivers for LED of the LC series. These are available in 350 and 700 mA, in constant current output and optional operating voltage of 12 or 24V. Ideal for low cost solutions. With standard terminals connection. Their tiny size, makes them a perfect suit for small size luminaries. Designed for LED power from 2 to 8W. Its low price makes this driver a very attractive item for downlights, decorative lighting, furniture, displays, spots or similar where the unitary cost plays a central role.

3Years

Guarantee

In compliance with EN 61347-2-13:2014/EN 61347-1:2015 EN 55015:2013+A1:2015/EN 61547:2009 EN 61000-4-2:2009/EN 61000-4-3:2006+A2:2010

APPLICATION

PRODUCT DESCRIPTION

Driver AC/DC LC SERIES

Current 350/700mA

Available 12-24V output

Screw connection terminal

3 years guarantee

For powerful LED

Class type II, without earth connection

SELV voltage

Compact design

DUNAMIC AC DRIVERS - LC SERIES 8,4W 350/700MA _ 12/24V - V1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

126


DUNAMIC LED DRIVERS IMPROVING

AC DRIVERS - LC SERIES 8,4W 350/700 MA_ 12/24V (59X41X21.2)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS D 3.6

Input range160-240V /50Hz

Max. output power 8W

Class type II

Protection against short circuit

FP > 0,5 full load

350/700mA in CC // 12-24V in CV

For fixtures integration, CE directives compliance

Weight = 50g

Wire length up to 1,5mm2

Soft Start – Soft switch off

BOX dimensions = 40,5x44x21,5mm

Maximum driver length 3 m

Tc = 80ºC

Operating temperature between -5ºC and -45ºC

41

59

45

51

Tc

r 1.8 (*) Measured in mm

SPECIFIC TECHNICAL DATA CODE

TYPE

INPUT VOLTAGE (V)

FRQUENCY (Hz)

COS (phi)

OUTPUT VOLTAGE (V)

OUTPUT CURRENT (A)

NOMINAL OUTPUT EFFICIENCY (%) POWER TOLERANCE (W) (iout)

31.60.AC.005.700 31.60.AC.005.700

700 mA 12v

230 230

50 50

0,576 0,543

3...12 12

0,7 0,7

2...8,4 8,4

(+/-)5% (+/-)5%

75% 85%

31.60.AC.005.350 31.60.AC.005.350

350 mA 24V

230 230

50 50

0,533 0,526

6...24 24

0,35 0,35

2...8,4 8,4

(+/-)5% (+/-)5%

75% 85%

(*) Values obtained at temperature Tc=75ºC. (**) Versions at constant current of 12 V and 24 V. (***) Efficiency values are measured at full load of 95-100%.

CONNECTION EXAMPLE Version with voltage 160-240 Vac

Vesion with current 160-240 Vac Dunamic LED Driver

Dunamic LED Driver

31.60.AC.005.700 Vin=210-220VAc 50/60 Hz tc I Max -0.05A I out = 700mA Cos Ø > 0.5 ta max. 50ºC

31.60.AC.005.350 Vin=210-220VAc 50/60 Hz tc I Max -0.05A I out = 350mA Cos Ø > 0.5 ta max. 50ºC

C

C 100

F

SEC24Vdc

PRI 230VAc SELV Equivalent

100

M

SELV Equivalent

- +

DUNAMIC AC DRIVERS - LC SERIES 8,4W 350/700MA _ 12/24V - V1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

M

SEC12Vdc

PRI 230VAc

- +

MERARKI 300 24 Vcc

F

- +

-

+

1W

1W

1W

3W

3W

3W

700 mA

127


DUNAMIC LED DRIVERS IMPROVING

TECHNOLOGY

AC DRIVERS - LC SERIES 8,4W 350/700 MA_ 12/24V (59X41X21.2)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER MERAKI DUNAMIC DRIVERS AC/DC must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules) connected in parallel. Family MERAKI have polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. MERAKI DUNAMIC DRIVERS AC/DC require specific protection against voltage picks or electrical network noise. ISOLATION MERAKI DUNAMIC DRIVERS AC/DC functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver is in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION MERAKI DUNAMIC DRIVERS AC/DC contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. MERAKI DUNAMIC DRIVERS AC/DC must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source, respecting its nominal values. MERAKI DUNAMIC DRIVERS AC/DC are designed to be incorporated inside small size light fixtures, the driver has two flaps for this use. Always avoid mechanical stress, compression stress or superficial voltage stress over the electronic components and/or driver holder. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs and electronic components. The driver is delivered with 0.5-1.5mm² connection wires for screw connection terminals. TEMPERATURE MERAKI DUNAMIC DRIVERS AC/DC life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=80°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%.

DUNAMIC AC DRIVERS - LC SERIES 8,4W 350/700MA _ 12/24V - V1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

128


DUNAMIC LED DRIVER IMPROVING

TECHNOLOGY

BUCK DC 24 - 48V (56,5X32X16,5MM)

I+D LED introduces BUCK DRIVER DC/DC from DUNAMIC LED DRIVERS family. It is a dimmable Step-Down by PWM and constant current input of 24-48V. BUCK DRIVER is designed to feed spotlights or LED modules at constant current. Its tiny size makes from it a perfect suit for small size luminaries, tracks, spots, etc. The driver includes quick connectors to facilitate IN/OUT connection. Operating current from 200mA to 900mA. BUCK DRIVER DC/DC are the ideal complement to work side by side with MERAKI LED MODULES family in CC, COB or with any other light engine.

3Years

Guarantee

In compliance with EN62384:2007/A1:2010 - EN61547:2013 EN61347-1:2009/A1:2013

APPLICATION

DUNAMIC LED DRIVER - BUCK DC 24-48V - V1.1_ES- www.idled.eu All rights reserved. This publication may be modified without prior notice.

PRODUCT DESCRIPTION

DC/DC driver (dimmable)

Output from 200mA to 900mA

Simple and fast to install

Quick connectors, Push-In type

Power up to 40W

SELV voltage

Compact design

High efficiency

129


DUNAMIC LED DRIVER IMPROVING

BUCK DC 24 - 48V (56,5X32X16,5MM)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS

SELV voltage

Operating temperature between -5ºC and +50ºC

Standard Tc 75°C (box)

Overload output protection

Weight 30g (box)

MOQ 50 units

Dimmable by DIM (digital PWM in input)

For wires of 0,5-1mm2 long

Up to 15 LED Vf=3V

Maximum length STEP/LED L: 5 m

For

CE

directives

compliance

(luminaries type I and II)

16.5

integration,

10

fixtures

56.5

32

(*) Measured in mm.

SPECIFIC TECHNICAL DATA CODE

INPUT OUTPUT MAX. OUTPUT TEMP. AMB. VOLTAGE VOLTAGE POWER (ºC) (Vcc) (Vcc) (W)

31.60.DC.BUCK.200 31.60.DC.BUCK.200 31.60.DC.BUCK.200 31.60.DC.BUCK.200 31.60.DC.BUCK.200 31.60.DC.BUCK.200 31.60.DC.BUCK.200

24-48 24-48 24-48 24-48 24-48 24-48 24-48

20-44 20-44 20-44 20-44 20-44 20-44 20-44

8.8 15.4 17.6 22 26.4 30.8 39.6

IOUT (mA)

DIMENSIONS (mm)

BOX

EFFICIENCY (%)

200 350 400 500 600 700 900

25x50x16.5mm 25x50x16.5mm 25x50x16.5mm 25x50x16.5mm 25x50x16.5mm 25x50x16.5mm 25x50x16.5mm

NO-(OF) NO-(OF) NO-(OF) NO-(OF) NO-(OF) NO-(OF) NO-(OF)

>75% >85% >85% >85% >90% >95% >95%

25x50x16. -5 to +50ºC -5 to +50ºC -5 to +50ºC -5 to +50ºC -5 to +50ºC -5 to +50ºC -5 to +50ºC

(*) All efficiency values here exposed have been measured at full charge (90-100%). (**) For driver delivery including protection box, please add the letter “B” behind the product code. Example: 31.60.DC.BUCK.900B. (***) All versions including protection box are only available in black (ABS V0) and have dimensions of 56,5x32x10 mm.

EFFICIENCY

EFFICIENCY (%) vs Nº OF LEDS for Vin=+48Vdc 100

Io=0,2A

90

Io=0,35A

80

Io=0,4A

Efficiency (%)

70 60

Io=0,5A

50

Io=0,6A

40

Io=0,7A

30

Io=0,9A

20 10 0 81

01

21 Number of leds

DUNAMIC LED DRIVER - BUCK DC 24-48V - V1.1_ES- www.idled.eu All rights reserved. This publication may be modified without prior notice.

41

6

130


DUNAMIC LED DRIVER IMPROVING

BUCK DC 24 - 48V (56,5X32X16,5MM)

TECHNOLOGY

DIMMING CURVES Output current (A) vs PWM Dimming (%) signal at 10KHz, Vpwm=+5V 1,00

Iled(A)

0,90 0,80

Io=0,2A

0,70

Io=0,35A

0,60

Io=0,40A

0,50

Io=0,5A

0,40

Io=0,6A

0,30

Io=0,7A

0,20

Io=0,9A

0,10 0,00 02

04

06 Pdim(%)

08

0

100

(*) Maximum voltage for dimming signals 10V. (**) Dimming between 1 and 20 KHz. (***) BUCK drivers show better linearity when input and output voltage pick are higher

Dunamic Buck Driver

Vin 48Vcc

CC Version

OUTPUT

CONNECTION EXAMPLE

31.60.DC.BUCK.200

-DIM +DIM

INPUT

+ -

+ + -

! WARNING CONNECTION

+ +

Vin:24-48V PMax:8.8W IOut:200mA

-

Dunamic Buck Driver

Vin 48Vcc

CC Version

31.60.DC.BUCK.200

-DIM +DIM

-

INPUT

+ -

OUTPUT

LED COB LIGHT ENGINE

+ + -

! WARNING CONNECTION

Vin:24-48V PMax:8.8W IOut:200mA

+

+ +

-

LED COB LIGHT ENGINE

PMW

DUNAMIC LED DRIVER - BUCK DC 24-48V - V1.1_ES- www.idled.eu All rights reserved. This publication may be modified without prior notice.

131


DUNAMIC LED DRIVER IMPROVING

BUCK DC 24 - 48V (56,5X32X16,5MM)

TECHNOLOGY

CONNECTION EXAMPLE

1

2 Vf led :15

cc

0V

23

Connect DC/DC BUCK to the LED module.

Connect voltage output from power source. I.e.:24Vcc.

3

4

c

Vc

24

ac 0V

P

ply

up

rs

e ow

23

Place inside the fixture.

DUNAMIC LED DRIVER - BUCK DC 24-48V - V1.1_ES- www.idled.eu All rights reserved. This publication may be modified without prior notice.

Close, connect and ready to use!

132


DUNAMIC LED DRIVER IMPROVING

TECHNOLOGY

BUCK DC 24 - 48V (56,5X32X16,5MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER BUCK DRIVER CC 24-48V must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). BUCK DRIVER CC 24-48V has polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. Family DUNAMIC LED DRIVERS require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION BUCK DRIVER CC 24-48V functions with SELV voltage, it does not require active isolation of the component as long as maximum reference (50v) SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION BUCK DRIVER CC 24-48V contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. BUCK DRIVER CC 24-48V must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source, respecting its nominal values and connection types according to the different LED modules as described in this data sheet. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs and electronic components. The driver must be introduced carefully inside the system or luminary. Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress on the PCB or light switch box. Always avoid mechanical stress, compression stress or superficial voltage stress over the electronic components and/or driver holder. Ideal wire for this connection type is strand or solid, multipolar or unipolar wire of 0,5-0,75 mm². TEMPERATURE BUCK DRIVER CC 24-48V life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=75°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +70 °C, and at a maximum humidity level of 65%.

DUNAMIC LED DRIVER - BUCK DC 24-48V - V1.1_ES- www.idled.eu All rights reserved. This publication may be modified without prior notice.

133


LENKER LED CONTROL

Office lighting_ Meraki 300-20 34V

New luminaries are conceived under single common criteria: good performance, high quality standards and control and regulation of light. This is why for I+D LED is possible to develop the best solutions for fixtures control trought wired and wireless protocols. As human interaction is increasingly getting present within smart luminaries, in I+D LED we have developed proximity and gestural sensors ideal for controlling LED modules, spotlights fixtures, under cabinet and bathroom lights and any standard driver with adjustable input in market. DALI/0-10V/BLUETOOTH/RF signals are essential in any new intelligent luminaries design. Our LENKER Bluetooth and RF system manages from few quentities of fixtures to a large number of luminaries groups. ODM, Custom products and OEM solutions have never been so easy with our flexible policy. Discover our system!

DIGITAL INTERFACE

WIRELESS

Pub_RGB Systems Dynamic

INTERFACES

Gesture sensor on/off and dimming

Available in differnt sizes

Instant calibration of sensors

Long lifetime > 40.000 hrs.

Wireless dimming for DALI drivers

Wireless dimming for 0-10V drivers

Wireless dimming for PMW drivers

Wireless dimming for TRIAC drivers

Dali and 0-10V DC/DC control gears

3-5 years limited warranty

SELV voltage drivers

High efficiency

Simple installation

Fast push-in connectors type

Low cost and low energy consumption

Suitable for indoor use

DIMMERS

Lettuce growing_horticultural light engine 134


LENKER LED CONTROL IMPROVING

TECHNOLOGY

RGBW WIRELESS DRIVER (BLUETOOTH MESH) (60X20MM)

I+D LED introduces RGBW WIRELESS STRIP LED DRIVER designed to control LED strips: RGB-RGBW, fixed colours and white strips. The device is controlled with any Android or iOS mobile or tablet. Its miniscule size allows the user to insert it into any type of luminaire. The driver is available in an open frame or in an IP65 protection box. It controls high powers in a certainly small format. The driver is ideal for RGB applications and light regulation for both domestic and professional areas.

3Years

Guarantee

In compliance with EN62384:2007/A1:2010 - EN61547:2013 EN61347 - 1:2009/A1:2013

APPLICATION

RGB WIRELESS STRIP LED DRIVER_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

PRODUCT DESCRIPTION

Dimming in white, RGB and RGBW

Light control and regulation

Easy and fast to install

Quick connectors: push-in

Available also with IP65 protection

Low energy consumption

Compact design

SELV voltage 12-24Vcc

135


LENKER LED CONTROL IMPROVING

RGBW WIRELESS DRIVER (BLUETOOTH MESH) (60X20MM)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS - OPEN FRAME

SELV voltage

Operating temperature between -5ºC and +55°C

Standard Tc 75°C

LED viewing angle 120°-160°

Weight open frame 12g, box 30g

MOQ 10 units

Dimmable via Bluetooth in Android or iOS

For 0,5-1mm2 wires

IP20 up to IP65 protection

Up to 100 devices per net

It is possible to group devices

Designed for stages, and timing control

IP 65

Dimensions: 85.7x31.7x16 mm

Signal coverage up to 45 m outdoor and 20 m indoor

60

20

PCB

(*) Measured in mm

DIMENSIONS - PROTECTION BOX

16

85.70

6.8

31.70

0

SPECIFIC TECHNICAL DATA CODE

VOLTAGE Input (V)

POWER/ CHANNEL (W)

MAX OUTPUT POWER (W)

31.40.WD.RGBW.01 12-24 Vcc 31.40.WD.RGBW.02 12-24 Vcc 31.40.WD.RGBW.03 12-24 Vcc

36W max 36W max 36W max

144W 144W 144W

Nº OF ROOM TEMP. DIMENSIONS BODY COLOR PROTOCOL IP CH (ºC) (MM)

4 CH 4 CH 4 CH

-5 to +050 -5 to +050 -5 to +050

60X19.8X6.5 RED BOARD 60X19.8X6.5 BLACK BOARD 60X19.8X6.5 BLACK BOARD

4.2 BTLE IP20 4.2 BTLE IP40 4.2 BTLE IP65

CAJA

NO YES YES

(*) Maximum distance between the controller mobile and driver: 25m indoor and 45m outdoor. (**) The driver can be utilize for RGB-RGBW-WHITE LED strips.

RGB WIRELESS STRIP LED DRIVER_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

136


LENKER LED CONTROL IMPROVING

RGBW WIRELESS DRIVER (BLUETOOTH MESH) (60X20MM)

TECHNOLOGY

INSTALLATION AND CONNECTION EXAMPLE IN

OUT

12-24 Vcc

Wire lenght 1mm2 max Led RGBW Wireless Tc Strip Led Driver

+ -

31.40.RGB21

Don´t cover this area with metalic materials

EN 62384 EN61547 EN61347

2,4 GHz

12-24 Vcc

LED STRIP 24 VCC 120 LED

+24 -W -G -R -B

RGB - 4CH

SE LV Do not cover with metallic materials the center of the driver, as indicated in the above image.

IN

Led RGBW Wireless Tc Strip Led Driver

+ -

Vin max:12-24V P max:144W I:1.5 max/CH

31.40.RGB21

Don´t cover this area with metalic materials

EN 62384 EN61547 EN61347

Note: For version including protection box, first introduce connection wires inside the In/Out hole.

OUT

Wire lenght 1mm2 max

Vin max:12-24V P max:144W I:1.5 max/CH 2,4 GHz

LED STRIP 24 VCC 60 LED +24 -G -R -B

SE LV

RGB - 3CH

Note: For version including protection box, first introduce connection wires inside the In/Out hole.

Do not cover with metallic materials the center of the driver, as indicated in the above image.

Wire lenght 1mm2 max

IN

OUT

12-24 Vcc

+ -

Led RGBW Wireless Tc Strip Led Driver 31.40.RGB21

EN 62384 EN61547 EN61347

Don´t cover this area with metalic materials

Vin max:12-24V P max:144W I:1.5 max/CH 2,4 GHz

+24 -W -G -R -B

SE LV Do not cover with metallic materials the center of the driver, as indicated in the above image. STEPS FOR WIRELESS CONNECTION

1. 2. 3. 4. 5. 6.

Download the Android or iOS application from the links provided with the products and instruction manual. Install the driver in a zone free of metal parts, as these will significantly affect the interaction with the control of the mobile or tablet. If you wish, you can also use the version including the protection box. Connect the driver according to the different possible connections here specified. Once the physical connection is complete, activate the Bluetooth of your phone or tablet, open the LENKER CONTROL app and pair it with the device. For security reasons, to add and pair a device to your control app, you must be within 1 meter from the device. Once the driver has been added and registered in the app, no other user can control it. In case there is no communication between the app and the device, restart the module. Press the reset button for 10 seconds and wait until the RGB, RGBW or White luminaire lights up for all channels. RGB WIRELESS STRIP LED DRIVER_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

137


LENKER LED CONTROL IMPROVING

TECHNOLOGY

RGBW WIRELESS DRIVER (BLUETOOTH MESH) (60X20MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER LENKER RGBW WIRELESS STRIP LED DRIVER must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). LENKER RGBW WIRELESS STRIP LED DRIVER has polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. Family LENKER LED CONTROL require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION LENKER RGBW WIRELESS STRIP LED DRIVER functions with SELV voltage, it does not require active isolation of the component as long as maximum reference SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION LENKER RGBW WIRELESS STRIP LED DRIVER contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. LENKER RGBW WIRELESS STRIP LED DRIVER must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source, respecting its nominal values and connection types according to the different LED modules as described in this data sheet. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs and electronic components. The driver must be introduced carefully inside the system or luminary. Maximum torque for fixing recommended 0,4-0,5 Nm. Always avoid mechanical stress, compression stress or superficial voltage stress over the electronic components and/or driver holder. Ideal wire for this connection type is strand or solid wire of 0,5 -1mm2. Important note: for proper device functioning, do not cover the wireless signal emission surface with any metallic component. TEMPERATURE LENKER RGBW WIRELESS STRIP LED DRIVER life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=55°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +70 °C, and at a maximum humidity level of 65%.

RGB WIRELESS STRIP LED DRIVER_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

138


LENKER CONTROL IMPROVING

TECHNOLOGY

DIGITAL INTERFACE

GESTURE SENSOR( 85.7X31.7X16MM)

I+D LED introduces an essential device, the GESTURE SENSOR LED CONTROL, designed as a DCDC driver to control linear LED strips in 24/48 V, spotlights or LED modules in constant current, drivers in 010V and PWM drivers in luminaires, with the palm of your hand. With a simple gesture we can regulate light, turn on the luminaire and leave it at the desired light intensity value. Ideal for kitchen applications: on furniture and kitchen counter, bathrooms, mirrors, etc. Its diversity of operating modes allows the designer to introduce the sensor to a new stage of lighting development, providing unusual intelligence to the luminary. Models with IP65 protection box are also available. GESTURE SENSOR LED CONTROL is the perfect fit for domestic or professional applications.

3Years

Guarantee

In compliance with EN62384:2007/A1:2010 - EN61547:2013 EN61347-1:2009/A1:2013

APPLICATION

LENKER CONTROL GESTURE SENSOR - V1.1_ES- www.idled.eu All rights reserved. This publication may be modified without prior notice.

PRODUCT DESCRIPTION

Dimming in white, ON/OFF

Total control with a single gesture

Light control and regulation

Easy and quick to install

Quick connectors, Push-In type

Optional to have IP65 protection

Low consumption

Drivers control 010V and PWM

Compact design

SELV voltage 12-48 Vcc

139


LENKER CONTROL IMPROVING

DIGITAL INTERFACE

GESTURE SENSOR( 85.7X31.7X16MM)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS

SELV voltage

Operating temperature between -5ºC and +55°C

Standard Tc 75°C

Sensor range 25-30 cm, in straight line

Weight 20 g – 45 g (box)

MOQ 50 units

Controlled and dimmed with you palm hand For wires of

31.7

85.7

From IP20 to IP65 protection

Regulation PWM / 010V

Custom and OEM

16

0,5-1 mm2 length

(*) Measured in mm

SPECIFIC TECHNICAL DATA CODE

INPUT VOLTAGE (Vcc)

31.40.GS.PMW 12-48 31.40.GS.PMW.IP65 12-48 31.40.GS.CV 12-48 31.40.GS.CV.IP65 12-48 31.40.GS.010V 12-48 31.40.GS.010V.IP65 12-48 31.40.GS.CC.200 12-48 31.40.GS.CC.350 12-48 12-48 31.40.GS.CC.400 31.40.GS.CC.500 12-48 31.40.GS.CC.700 12-48 31.40.GS.CC.200.IP65 12-48 31.40.GS.CC.650.IP65 12-48 12-48 31.40.GS.CC.400.IP65 31.40.GS.CC.500.IP65 12-48 31.40.GS.CC.700.IP65 12-48

MAX. POWER OUTPUT (W)

INTENSITY (A)

Signal ONLY Signal ONLY 100W max 100W max Signal ONLY Signal ONLY 48W 48W 48W 48W 48W 48W 48W 48W 48W 48W

N/A N/A 2 2 N/A N/A 1A 1A 1A 1A 1A 1A 1A 1A 1A 1A

TEMP. (ºC)

DIMENSIONS (mm)

25x50x16. -5 to +50ºC 60X19.8X6.5 -5 to +50ºC 85.7X31.7X16 -5 to +50ºC 60X19.8X6.5 -5 to +50ºC 85.7X31.7X16 -5 to +50ºC 60X19.8X6.5 -5 to +50ºC 85.7X31.7X16 -5 to +50ºC 60X18.8X6.5 -5 to +50ºC 60X18.8X6.5 -5 to +50ºC 60X18.8X6.5 -5 to +50ºC 60X18.8X6.5 -5 to +50ºC 60X18.8X6.5 -5 to +50ºC 85.7X31.7X16 -5 to +50ºC 85.7X31.7X16 -5 to +50ºC 85.7X31.7X16 -5 to +50ºC 85.7X31.7X16 -5 to +50ºC 85.7X31.7X16

COLOUR PROTOCOLO

RED BOARD BLACK RED BOARD BLACK RED BOARD BLACK RED BOARD RED BOARD RED BOARD RED BOARD RED BOARD BLACK BLACK BLACK BLACK BLACK

GESTURE GESTURE GESTURE GESTURE GESTURE GESTURE GESTURE GESTURE GESTURE GESTURE GESTURE GESTURE GESTURE GESTURE GESTURE GESTURE

IP

IP20 IP65 IP20 IP65 IP20 IP65 IP20 IP20 IP20 IP20 IP20 IP65 IP65 IP65 IP65 IP65

BOX PROXIMITY QTY of DISTANCE DRIVES

NO YES NO YES NO YES NO NO NO NO NO YES YES YES YES YES

30 25 30 25 30 25 30 30 30 30 30 25 25 25 25 25

10-15 10-15 N/A N/A 10-15 10-15 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A

(*) All avalbale data herby exposed has been taken at 35ºC of temperature.

INSTALLATION EXAMPLE AND USAGE 1.

Connect device to power Vin=24-48 Vcc. Connect the LED to Vout as indicated by the drawing. Note: pierce IN and OUT wires through silicone membranes at the box sides when choosing for IP65 box.

2.

Place the connector inside its box. The optical sensor parts (cover and base) must coincide perfectly, as indicated by the drawing.

3.

Sensor is installed. Place/stick the double sided tape over sensor’s base or cover, depending on the required design.

4.

Remove upper film tape and stick the sensor on the lower side of the furniture or desired place, as indicated by the drawing.

5.

Operating gestures:

5.1. ON/OFF: Move the palm of your hand on a moderate speed from right to left or vice versa to switch LED on and off.

5.2. Dimming DOWN: Move the palm of your hand towards the sensor in a straight line.

5.3. Dimming UP: Move the palm of your hand away from the sensor in a straight line.

LENKER CONTROL GESTURE SENSOR - V1.1_ES- www.idled.eu All rights reserved. This publication may be modified without prior notice.

140


LENKER CONTROL IMPROVING

DIGITAL INTERFACE

GESTURE SENSOR( 85.7X31.7X16MM)

TECHNOLOGY

IMPORTANT REMARKS 1.

Moderate speed movements for the sensor refer to a hand wave gesture of 0,5-1 seconds long in front of the sensor.

2.

For UP or DOWN dimming options, once the light intensity value has been selected, the user should remove the hand to the right or left with a fast hand wave movement to keep the selected dimming intensity.

3.

At 3 cm from the sensor, light intensity will be at 10%.

4.

At 30 cm from the sensor, light intensity will be at 100%. At 24,6 cm from the sensor, light intensity will be at 80%.

1

24-48 Vcc + + -

Connect to power supply. Note: Pierce IN and OUT wires through silicone membranes at the box sides.

2 PMMA optical sensor Joint

Sensor cover

Vin 24-48 Vcc

Joint

Place the sensor in its box, make sure the optical sensor

Sensor base

adjust in and the cover by pressing on the base.

LENKER CONTROL GESTURE SENSOR - V1.1_ES- www.idled.eu All rights reserved. This publication may be modified without prior notice.

141


LENKER CONTROL IMPROVING

TECHNOLOGY

DIGITAL INTERFACE

GESTURE SENSOR( 85.7X31.7X16MM)

3

Connected product.

4

V in

Move your hand as indicated in the drawing. Dimming down 10% intensity at 8 cm distance from sensor. Dimming up 80% intesity at 24,6 cm distance from sensor. LENKER CONTROL GESTURE SENSOR - V1.1_ES- www.idled.eu All rights reserved. This publication may be modified without prior notice.

142


LENKER CONTROL IMPROVING

TECHNOLOGY

DIGITAL INTERFACE

GESTURE SENSOR( 85.7X31.7X16MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER LENKER GESTURE SENSOR CONTROL must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). Family LENKER GESTURE SENSOR CONTROL has polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. BUCK DRIVER CC 24-48V has integrated protection against reverse polarity errors. Family LENKER GESTURE SENSOR CONTROL require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION LENKER GESTURE SENSOR CONTROL functions with SELV voltage, it does not require active isolation of the component as long as maximum reference SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION LENKER GESTURE SENSOR CONTROL contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. LENKER GESTURE SENSOR CONTROL must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source, respecting its nominal values and connection types according to the different LED modules as described in this data sheet. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs and electronic components. LENKER GESTURE SENSOR CONTROL modules must be introduced carefully inside the system or luminary. The lower side of the module is the most fragile part of it. It is required to work with care in order to not damage the device. The installation must be done with ESD protection. Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress on the PCB. Always avoid mechanical stress, compression stress or superficial voltage stress over the electronic components and/or driver holder. Ideal wire for this connection type is strand or solid wire, unipolar or multipolar wire of 0,5-1mm². TEMPERATURE LENKER GESTURE SENSOR CONTROL life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=55°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20°C and +70°C, and at a maximum humidity level of 65%.

LENKER CONTROL GESTURE SENSOR - V1.1_ES- www.idled.eu All rights reserved. This publication may be modified without prior notice.

143


LENKER LED CONTROL IMPROVING

TECHNOLOGY

DIMMERS - DIM 10A 12-24V (45X45)

New DIMMER 10A offers the most steady and flexible control for luminous intensity. Under the scope of installation technicians, light fixtures manufacturers and architects who seek a quality regulation of luminous flux with LED technology. DIMMER 10A modules incorporate BAM / PWM technology in all their version models. Higher efficiency than 95% and 100% compatible with PCBs, LED strips and linear monochromatic 12-24 Vcc LED modules. On account off its exclusive design in miniscule size, it is possible to introduce the module in any standard light switch box and use standard electrical components. All models are possible to customize and have 3 years guarantee. The modules are designed to enable intensity regulation of LED systems that work on constant current. For proper functioning and according to customer’s needs, the module requires

3Años

protected constant current input of 12-24 Vcc.

GARANTÍA

The modules are presented in 3 types: control with encoder or In compliance with

linear potentiometer, for switchers and inverted encoder.

IEC 60669

APPLICATION

PRODUCT DESCRIPTION

12-24 Vcc input

Maximum dimensions 45x45x35MM

Efficiency > 95%

Open frame product

Digitally regulated PWM_BAM

1 channel

Regular power 240W

High resolution

Simple connection to constant voltage

LENKER LED CONTROL - DIMMERS - DIM 10A 12-24V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

144


LENKER LED CONTROL DIMMERS - DIM 10A 12-24V (45X45)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS

Operating temperature between -20 ºC and 45 ºC

Standard Tc 75 ºC

8 BITS resolution

REFRESH frequency 400 Hz

BAM_PWM regulated

1 CH, monochromatic regulation

Memory. Saves last selected values

MOQ 25 units

Weight 30 g

Packaging box weight (approx.) 900 g

For fixtures integration, CE directives compliance

Ø

45

45

SELV voltage

3

30

ENCODER INV 45

UP

45

++ - -

++ - -

++ - -

++ - -

++ - -

++ - -

(*) 41

(*) 30

DOWN

(*) 30

DOWN

45

UP

45

UP COM DOWN

45

REGLETA UP & DOWN

45

ENCODER

33.78

11

IMPROVING

(*) Total distance (**) Max. Wire section 0,5 / 1,5 mm2 (***) Measured in mm

SPECIFIC TECHNICAL DATA CODE

VOLTAGE Vin (V)

VOLTAGE (V)

CURRENT 0-10 A

MAX. POWER

REGULATION

DIMENSIONS

31.34.01012 31.34.01013 31.34.01014

12-24 12-24 12-24

12V 12V 12V

0-10A 0-10A 0-10A

120 W 120 W 120 W

Encoder INVERTED Encoder Switch UP&DOWN

45x45x30mm 45x45x41mm 45x45x30mm

31.34.01015 31.34.01016 31.34.01017

12-24 12-24 12-24

24V 24V 24V

0-10A 0-10A 0-10A

240 W 240 W 240 W

Encoder INVERTED Encoder Switch UP&DOWN

45x45x20mm 45x45x41mm 45x45x20mm

(**) Operating temperature between: -20ºC and +40ºC

LENKER LED CONTROL - DIMMERS - DIM 10A 12-24V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

145


LENKER LED CONTROL IMPROVING

DIMMERS - DIM 10A 12-24V (45X45)

TECHNOLOGY

CONNECTION EXAMPLE - VOUT=24VCC

Up

230Vcc

Vout

24Vcc

Ps: 24Vcc

Down

+

+ -

Pled

-

Out

Vin

230Va UP

COM

DOWN

Pled: 100W CONNECTION EXAMPLE - 24VCC WITH POTENTIOMETER OR ENCODER

230Vcc

Ps: 24Vcc

Vout

24Vcc

+

+ -

Pled

Out

Vin

230Va

Pled: 100W

UP

DOWN

PUSH ON

PUSH OFF

INSTALLATION EXAMPLE IN LIGHT SXITCH BOX Join enconder’s shaft to mechanism’s knob

In models for up and down switiches, introduce the dimmer in the mechanism box. LENKER LED CONTROL - DIMMERS - DIM 10A 12-24V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

146


LENKER LED CONTROL IMPROVING

TECHNOLOGY

DIMMERS - DIM 10A 12-24V (45X45)

SECURITY AND INSTALLATION INFORMATION ALIMENTACIÓN Los DIMMERS 10A deben estar alimentados a tensión constante y estabilizada. Dicha fuente de alimentación deber tener la potencia acorde con la cantidad de módulos a conectar en paralelo. La familia LENKER LED CONTROL tiene polaridad y deber ser respetada así como las tensiones y corrientes nominales. En caso contrario el módulo se vera dañado irreversiblemente. Un driver con protección contra cortocircuito, elevada temperatura y sobrecargas debe de ser usado con los DIMMER 10A. AISLAMIENTO El DIMMER 10 A trabaja a una tensión SELV, no es necesario ningún tipo de aislamiento con partes activas, siempre que no se excedan las tensiones SELV. El driver tendrá que cumplir en todo momento la normativa vigente de CE, UL o similares. ESD – INFORMACIÓN SOBRE ESTÁTICA Los DIMMER 10 A poseen componentes electrónicos especialmente sensibles a la electroestática. Por lo que es recomendable que se tomen las medidas adecuadas para manipular dichos componentes y que en ningún caso los módulos DIMMERS sean manipulados sin la correspondiente protección ESD. Si necesita mas información visite nuestra página web en donde encontrar más información sobre este tema. www.idled.eu. MONTAJE E INSTALACIÓN I+D LED S.L. no se hace responsable de la instalación. El instalador deber de colocar los DIMMERS 10 A de forma correcta y respetando los valores eléctricos nominales. LOS DIMMERS 10 A poseen 4 taladros de sujeción para tornillos M3 y pueden ser introducidos dentro de una caja eléctrica estándar (sin partes activas) o equivalentes. En todos los casos la fuerza de ajuste del tornillo nunca deberá ser superior a 0,5Nm, para evitar el estrés por compresión o tensión superficial sobre los componentes electrónicos de la PCB. Todos los DIMMER tienen la cabeza del tornillo DIN marcada sobre la PCB. Se recomienda utilizar tornillos DIN de cabeza plana. Si se utiliza algún tipo sustancia química en la instalación, no deberá tener ningún tipo de curado mediante condensación de gases o elementos abrasivos que dañen los componentes electrónicos. El cable idóneo para utilizar para la conexión es el flexible multipolar 0,4 -1,5mm2 (potencia dividida en dos regletas de conexión), con un pelado de 6mm. TEMPERATURA La vida útil de los DIMMER 10 A depende en gran medida de la temperatura. Bajo ningún concepto se deben sobrepasar los límites de temperatura de trabajo indicados (Tc=75°C), ya que la respuesta y funcionamiento del aparato se verán sensiblemente afectados. Se deberán comprobar los datos de temperatura ambiente en el peor de los casos para garantizar las horas de vida así como asegurar la garantía. Los dispositivos deberán de almacenarse a una temperatura entre -20ºC y +80ºC y humedad máxima del 65%.

Tc ≤ 75°C

LENKER LED CONTROL - DIMMERS - DIM 10A 12-24V - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

147


LENKER LED CONTROL IMPROVING

DIMMERS - DIM 30A 12-24V (134,7X110X48,2MM)

TECHNOLOGY

New DIMMER 30A offers the most steady and flexible control for luminous intensity. Under the scope of installation technicians, light fixtures manufacturers and architects who seek a quality regulation of luminous flux with LED technology. DIMMER 30A modules incorporate BAM / PWM technology in all their version models. Higher efficiency than 95% and 100% compatible with PCBs, LED strips and linear monochromatic 12-24 Vcc LED modules. On account off its exclusive design in miniscule size, it is possible to use them in any electrical system. The modules are designed to enable intensity regulation of LED systems that work on constant current. For proper functioning and according to customer’s needs, the module requires protected constant current input of 12-24 Vcc. The modules are presented in 2 functioning modes: masters or slaves. All models are possible to customize and have 3 years

5Años

guarantee.

GARANTÍA

Conforme con: EN62384:2007/A1:2010 - EN61547:2013 EN61347-1:2009/A1:2013

APPLICATION

PRODUCT DESCRIPTION

Output in constant voltage 12-24V

Max. current Iin/Iout = 30A

Up to 720W of power

High efficiency > 96%

Easy to install

Digitally regulated PWM/BAM 500-2KHz

Life-time exceeds 30.000 hrs.

3 years guarantee

Reverse polarity protection

Remote regulation or over device regulation

(by standard up and down switches)

LENKER CONTROL - DIMMERD - DIM 30A 12-24V- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

148


LENKER LED CONTROL IMPROVING

DIMMERS - DIM 30A 12-24V (134,7X110X48,2MM)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS 134.7 110

SELV voltage

Regulation range 0,1-100%

Controlled by internal or external buttons

Max. 100 metres for external buttons (wire<0,5mm2)

Operating temperature between -20ºC and 55º C

8 BITS resolution

1 CH - monochromatic regulation

Refresh frequencies 500Hz o 2KHz

Memory from lastest setting value

Standard Tc 75ºC

LED mode indicator

2 modes: Master o Slave

20 metres max. between Master and Slave

Weight 200 gr

MOQ 10 pcs (individual packaging)

Possibility to integrate with LOGO Custom

Tc ºC

110

85.7

R2.2

48.2

119.7

(*) Max. cable length 0,5/1,5 mm2. (**) Measured in mm.

SPECIFIC TECHNICAL DATA CODE

VOLTAGE Vin (V)

VOLTAGE (V)

CURRENT 0-30 A

MAX. POWER

REGULATION MODE

DIMENSIONS

F(Hz)

31.40.DIM30 31.40.DIM30 31.40.DIM30

10-25 10-25 10-25

12V 12V 12V

0-30A 0-30A 0-30A

360 W 360 W 360 W

MASTER MASTER SLAVE

134.7x110x48.2mm 134.7x110x48.2mm 134.7x110x48.2mm

500Hz 2KHz n/a

31.40.DIM30 31.40.DIM30 31.40.DIM30

10-25 10-25 10-25

24V 24V 24V

0-30A 0-30A 0-30A

720 W 720 W 720 W

MASTER MASTER SLAVE

134.7x110x48.2mm 134.7x110x48.2mm 134.7x110x48.2mm

500Hz 2KHz n/a

(**) Operating temperature between -20ºC and +40ºC

SPECIFIC TECHNICAL DATA 40 35 30 25 lo(A)

20 Dimming Slope

15 10 5 0 11 02 03 04 05 06 07 08 09 09 9 Dimming Duty Cicle(%) LENKER CONTROL - DIMMERD - DIM 30A 12-24V- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

149


LENKER LED CONTROL IMPROVING

DIMMERS - DIM 30A 12-24V (134,7X110X48,2MM)

TECHNOLOGY

OPERATING MODE SELECTION DIMMER 30A has two operating modes: MASTER or SLAVE. When the dimmer is set on MASTER mode, the dimmer itself generates the dimming sign and its setting are controlled by the device. On the other hand, on SALVE mode the control signal provides from another DIMMER 30A device in MASTER mode or from an external PWM generator. For SLAVE setting, light regulation is voided at the device and controlled externally.

tc Max. ON

UP

SLAVE

1 2 3 4

DOWN

+

OUTPUT LED

!

MASTER

WARNING CONNECTION

-

INPUT + 12V + 24V

+

-

500Hz 2KHz M/S LINK = DOWN

Lenker Dim30 PMax:720W IEC 60669

MASTER = UP SLAVE = DOWN

EXTERNAL SWITCHES

EXTERNAL PMW iNPUT

GND EXT

+

UP

DOWN GND

MASTER TYPE Max. wire length 5-6 mm2 + tc Max. ON

12-24 Vcc

+

+

-

-

OUTPUT LED

-

WARNING CONNECTION

-

DOWN

MASTER

!

+

INPUT + 12V + 24V

+

Max. wire length 5-6 mm2

+

UP

SLAVE

+

500Hz 2KHz M/S LINK = DOWN

Lenker Dim30 PMax:720W IEC 60669

MASTER = UP SLAVE = DOWN

EXTERNAL SWITCHES

EXTERNAL PMW iNPUT

+

GND EXT

+

UP

DOWN GND

-

NOTE: Always set operating mode before connecting DIMMER 30A to electrical power.

LENKER CONTROL - DIMMERD - DIM 30A 12-24V- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

150


LENKER LED CONTROL IMPROVING

DIMMERS - DIM 30A 12-24V (134,7X110X48,2MM)

TECHNOLOGY

SLAVE MODE

Max. wire length 5-6 mm2

Max. wire length 5-6 mm2 +

tc Max.

12-24 Vcc

ON

+

UP

-

+

+

OUTPUT LED

-

DOWN

MASTER

!

+

INPUT + 12V + 24V

+

WARNING CONNECTION

SLAVE

-

-

-

+

500Hz 2KHz

Lenker Dim30

M/S LINK = DOWN

EXTERNAL SWITCHES

-

PMax:720W IEC 60669

MASTER = UP SLAVE = DOWN

+ EXTERNAL PMW iNPUT

GND EXT

+

UP

DOWN GND

-

MASTER Max. wire length 1.5 mm2 Min wire length1 mm2

+ tc Max. ON

+

UP DOWN

!

MASTER

+

+

-

-

OUTPUT LED

-

INPUT + 12V + 24V

+

WARNING CONNECTION

SLAVE

+

500Hz 2KHz M/S LINK = DOWN

Lenker Dim30 PMax:720W IEC 60669

MASTER = UP SLAVE = DOWN

EXTERNAL SWITCHES

EXTERNAL PMW iNPUT

+

GND EXT

+

UP

DOWN GND

-

SLAVE

Max. wire length 5-6 mm2 NOTE: Always set operating mode before connecting DIMMER 30A to electrical power.

LENKER CONTROL - DIMMERD - DIM 30A 12-24V- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

151


LENKER LED CONTROL IMPROVING

DIMMERS - DIM 30A 12-24V (134,7X110X48,2MM)

TECHNOLOGY

SLAVE TYPE (EXTERNAL CONTROL)

Max. wire length 5-6 mm2

Max. wire length 5-6 mm2 +

tc Max.

12-24 Vcc

ON

+

UP

-

+

+

-

-

OUTPUT LED

-

DOWN

MASTER

!

+

INPUT + 12V + 24V

+

WARNING CONNECTION

SLAVE

+

500Hz 2KHz

Lenker Dim30

M/S LINK = DOWN

EXTERNAL SWITCHES

-

PMax:720W IEC 60669

MASTER = UP SLAVE = DOWN

EXTERNAL PMW iNPUT

+

GND EXT

+

UP

DOWN GND

-

NOTE: Always set operating mode before connecting DIMMER 30A to electrical power. PMW Generator

+ END

PULSADORES EXTERNOS (CONNECTION) Max. wire length 5-6 mm2

Max. wire length 5-6 mm2 +

tc Max.

12-24 Vcc

ON

+

UP

-

+

+

-

-

OUTPUT LED

-

DOWN

MASTER

!

+

INPUT + 12V + 24V

+

WARNING CONNECTION

SLAVE

+

500Hz 2KHz M/S LINK = DOWN

Lenker Dim30 PMax:720W IEC 60669

MASTER = UP SLAVE = DOWN

EXTERNAL SWITCHES

+

EXTERNAL PMW iNPUT

GND EXT

+

UP

DOWN GND

-

Max. wire length 1.5 mm2 Min wire length1 mm2 UP GND DOWN

LENKER CONTROL - DIMMERD - DIM 30A 12-24V- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

NOTE:

During MASTER mode, internal and external switches are enabled. The dimmer will respond to one or the other depending on which one is in use, but never to both at the same time. During SLAVE mode internal switches are disabled, hence will not respond.

152


LENKER LED CONTROL IMPROVING

TECHNOLOGY

DIMMERS - DIM 30A 12-24V (134,7X110X48,2MM)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER LENKER LED CONTROL DIMMER 30A must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules) connected in parallel. LENKER LED CONTROL DIMMER 30A has polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. Family LENKER LED CONTROL require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION LENKER LED CONTROL DIMMER 30A functions with SELV voltage, does not require active isolation of the component as long as maximum reference (50v) SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION LENKER LED CONTROL DIMMER 30A contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. LENKER LED CONTROL DIMMER 30A must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source, respecting its nominal values. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs and electronic components. DIMMERS 30A are delivered with 4 fastening pre-made holes for M3 screws and can be introduced inside a standard light switches box (with no active parts) or equivalent. Maximum torque for fixing recommended 0,5 Nm to avoid mechanical stress, compression stress or superficial voltage stress over the PBC’s electronic components. All DIMMERS’ PCBs have mounting holes imprinted for placing reference of DIN screws. It is recommended to use flat head DIN screws. Ideal wire for this connection type during installation is multipolar flexible wire of 5-6 mm² with a strip wire of 6MM. Note: regarding total power and current, it is recommended to split the charge between two wires of 15A each and 2,5mm2 length in the terminals. TEMPERATURE LENKER LED CONTROL DIMMER 30A life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=75°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%.

LENKER CONTROL - DIMMERD - DIM 30A 12-24V- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

153


LENKER LED CONTROL IMPROVING

TECHNOLOGY

DIMMERS - DIM 30A 12-24V (134,7X110X48,2MM)

IMPORTANTE INFORMACIÓN FUNCIONAMIENTO ENCENDIDO Tras el proceso de encendido y de selección de modo Master o modo Slave en cualquiera de sus dos frecuencias (500Hz y 2kHz), el DIMMER LENKER 30A se enciende y gradualmente alcanza el máximo valor de corriente que permanece indefinidamente hasta que se modifica su valor a través de los pulsadores Up y Down. Si transcurrido un tiempo de funcionamiento se produce un apagado, cuando el DIMMER LENKER 30A vuelva a ponerse en marcha entregará el último valor de corriente que tenía configurado justo antes de producirse su apagado. CAMBIO DE FRECUENCIA Durante el funcionamiento del dimmer en un determinado modo, se puede cambiar la frecuencia de funcionamiento de 500Hz a 2KHz y viceversa, sin tener que apagar el dispositivo. Tras realizar el cambio de frecuencia, el DIMMER LENKER 30A alcanzará gradualmente el nuevo valor de frecuencia seleccionado. CAMBIO DE MODO NO se ha de cambiar el modo de funcionamiento de Master a Slave mientras el DIMMER LENKER 30A esté en marcha. Esta operación se ha de configurar con el dispositivo apagado y una vez hecho encenderlo nuevamente. En caso de configurar el dimmer mientras esté en marcha, los pulsadores funcionarán de manera invertida. NO se ha de cambiar el modo de funcionamiento de Slave a Master mientras el DIMMER LENKER 30A esté en marcha. Esta operación se ha de configurar con el dispositivo apagado y una vez hecho encenderlo nuevamente. Por motivos de seguridad no es posible configurar este modo mientras el el dimmer mientras esté en marcha y los LEDs conectados a la salida permanecerán apagados. Ante cualquier combinación aquí no especificada en el switch, el DIMMER LENKER 30A no funcionará y mantendrá la última configuración que se considere correcta.

LENKER CONTROL - DIMMERD - DIM 30A 12-24V- V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

154


ALTUS LED LIGHTS ENGINES Withing the ALTUS FAMILY you will find high-end products designed for different solutions and several fields. For instance: signage fixtures, backlighting signs, horticultural luminaries, treet lighting modules, UVC water/air disinfection equipment and accesiries for bathroom and under cabinet lighting for kitchens, shelfs, market´s food lightinf. Changes in any light engine are possible thanks to our flexible policy.

LED LIGHT ENGINES

Custom horticultural fixtures

Luminaries with control gears an wireless solutions integrated

Customizable sizes of profiles

Cabinet light for restaurants/kitchens

Food lighting for exhibitors

Citrus rotten detectors

Street lighting modules for retrofit

Street lighting LED MODULES

From 2000K to 5000K (70-90 CRI)

Turnkey projects

Cinema Staris_ LED Altus profile 155


DIGITAL RGB DIGITAL RGB FIXTURE EASY BOX IMPROVING

(DYNAMIC RGB)

TECHNOLOGY

I+D LED in partnership with Iluxstudio present RGB digital panels. Dynamic by nature, these modules are able to reproduce any vibrant and imaginable plot of shapes, color changes, objects, videos and more... The panels are extremely easy to connect and assembly to each other due to its simple and modular design. Easy box makes possible to build vertical and horizontal decorative separations, and even with the 60x60 model, as replacement for ceiling panels of different sizes. The module works with SELV voltage. The panels are available with different diffusers, in with black or white finish to achieve more elegant options.

lm/$

>135 lm/w

2Years

Guarantee

In compliance with EN 60598 : 2015

APPLICATION

DIGITAL RGB FIXTURE EASY BOX (DYNAMIC RGB) - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

PRODUCT DESCRIPTION

Enormous number of possible applications

Easy and fast connection

Wire to wire connectors

Possibility of modular forms

Video reproduction

Compact design, only 70 mm high

SELV voltage 5-12V

Dynamic illumination

Controlled by PC or pre-installed programs

156


DIGITAL RGB DIGITAL RGB FIXTURE EASY BOX IMPROVING

(DYNAMIC RGB)

TECHNOLOGY TECHNICAL DATA

DIMENSIONS

SELV voltage

Available 60 LED/m and more than 256 pixels per module

Operating temperature between -20ºC and +45°C

EN 61471:2008 group 1

Standard Tc 55°C

Viewing LED angle 120°-160°

Weight 2,5 Kg/m2

MOQ 10 units

Adjustable y programmable

70

297.50 297.50

595

297.50

70

EB3030 238

58 EB3060 70

297.50

268.6

by MADRIX – SPI DMX 512 protocol

EBEXA30 70

595

892.5

595 (*)

(*) Measured in mm EB3090

EB6060

SPECIFIC TECHNICAL DATA VOLTAGE

POWER (W)

PIXELS RGB

ROO TEMP. (ºC)

DIMENSIONS (mm)

BODY COLOR

IP

DIFFUSER

31.65.EB3030 31.65.EB6060 31.65.EB3090 31.65.EB3060 31.65.EBEXA30 31.65.EFLEX_122020 31.65.EFLEX_122067

5V 5V 5V 5V 5V 12V 12V

19,5 77 57,6 38,5 19,5 14,4 14,4

64 256 192 128 37 20 20

1-45ºC 1-45ºC 1-45ºC 1-45ºC 1-45ºC 1-45ºC 1-45ºC

297.5x297.5x70 595x595x70 892.5x297.5x70 297.5x595x70 270x240x70 5000x10x4 5000x10x4

AL BLACK AL BLACK AL BLACK AL BLACK AL BLACK WHITE WHITE

IP20 IP20 IP20 IP20 IP20 IP20 IP67

WHITE WHITE WHITE WHITE WHITE N/A N/A

31.65.EB3030.B 31.65.EB6060 31.65.EB3090 31.65.EB3060 31.65.EBEXA30 31.65.EFLEX_122020 31.65.EFLEX_122067

5V 5V 5V 5V 5V 12V 12V

19,5 77 57,6 38,5 19,5 14,4 14,4

64 256 192 128 37 20 20

1-45ºC 1-45ºC 1-45ºC 1-45ºC 1-45ºC 1-45ºC 1-45ºC

297.5x297.5x70 595x595x70 892.5x297.5x70 297.5x595x70 270x240x70 5000x10x4 5000x10x4

AL BLACK AL BLACK AL BLACK AL BLACK AL BLACK WHITE WHITE

IP20 IP20 IP20 IP20 IP20 IP20 IP67

WHITE WHITE WHITE WHITE WHITE N/A N/A

CODE

(*) Power values for flexible strips are described per linear metre. (**) For all the versions it is required MADRIX license (not included, which version is determined by the quantity of pixels). (***) For all the devices is it required a pixel and pixel controller (not included) and power supply. (****) MADRIX/DMX programming is not included. Maximum number of drivers depends on the quantity of connected pixels.

DIGITAL RGB FIXTURE EASY BOX (DYNAMIC RGB) - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

157


DIGITAL RGB DIGITAL RGB FIXTURE EASY BOX IMPROVING

(DYNAMIC RGB)

TECHNOLOGY CONNECTION EXAMPLE - 3 UNITS

SD CARD (PREVIOUSLY PROGRAMMED)

DRIVER STAND ALONE

5-24 Vcc

CH 8

80-265 Vac 230V

8 CHANNELS ( MAX. 1080 PIXELS PER CHANNEL)

5Vcc

SPI

POWER SUPPLY

+5V

+5V

Dout

Din

+5V

Dout

Din

Dout

Din DATA IN

No connection 37PX

37PX

37PX

OPERATING MODE A .“Stand Alone” applications, simple and semi-professional SD CARD (PREVIOUSLY PROGRAMMED)

DRIVER STAND ALONE

5-24 Vcc

CH 8 80-265 Vac 230 V

8 CHANNELS ( MAX. 1080 PIXELS PER CHANNEL)

Vcc

POWER SUPPLY

DATA OUT

SPI

54 EB

EB

+5V

* No PC required. Just tell us what type of programming you need and we Sin conectar will deliver a programmed SD card.

Dout

DIGITAL RGB FIXTURE EASY BOX (DYNAMIC RGB) - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

EB +5V

+5V

Din

Dout

Din

Dout

Din DATA IN

158


DIGITAL RGB DIGITAL RGB FIXTURE EASY BOX IMPROVING

(DYNAMIC RGB)

TECHNOLOGY

B . Professional applications

80-265 V5

-24Vcc

POWER SUPPLY

DinD

out

DinD

out

Nebula Nº1

PC MADRIX CONTROLLER

Nebula Nº1

ETHERNET -RACK

Nebula Nº1

+5V

+5V

+5V SIN CONECTAR

Din

Dout

37PX

Din

Dout

37PX

Din

Din

37PX

* For professional applications of dynamic programming and high quantity of pixels it is required some controllers, PC’s and licenses. Let us know about you project, and we will give you a suitable and complete advise!

DIGITAL RGB FIXTURE EASY BOX (DYNAMIC RGB) - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

159


DIGITAL RGB DIGITAL RGB FIXTURE EASY BOX IMPROVING

TECHNOLOGY

(DYNAMIC RGB)

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER EASY BOX RGB must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (or group of modules). EASY BOX RGB has polarity, for this reason rated current, nominal power and polarity must be taken into account. If that is not the case, the module might be irreversibly damaged. EASY BOX RGB require specific driver protection against short-circuit currents, temperature raise and overloads. ISOLATION EASY BOX RGB functions with SELV voltage, does not require active isolation of the component as long as maximum reference SELV voltage is not exceeded. In other case, it will be mandatory earth connection on all conductive components of the fixture or light engine when the number of modules in the series exceeds SELV voltage. The driver must be in compliance with CE, UL or valid analogous regulation. ESD – STATIC ELECTRICITY INFORMATION EASY BOX RGB contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. EASY BOX RGB must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source, respecting its nominal values and different connections for the diverse drivers. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs and electronic components. The panels will be supplied with wall /ceiling fastening with a minimum spread of 10 mm. Maximum torque for fixing recommended 0,4-0,5 Nm to avoid mechanical stress. Caution may be taken when placing and connecting the panels, they must be treated carefully. Always avoid mechanical stress, compression stress or superficial voltage stress over the panel or its electronic components. Ideal wire for this connection type is multipolar flexible wire of 0,5-1,5 mm² for data wires, and a minimum of 1,5 mm² for power supply connection wire, in order to have a maximum voltage of 0,5-V1 in the latest device. TEMPERATURE EASY BOX RGB life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=55°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. Store modules between -20 °C and +80 °C, and at a maximum humidity level of 65%.

DIGITAL RGB FIXTURE EASY BOX (DYNAMIC RGB) - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

160


ALTUS LIGHT ENGINES IMPROVING

STEP ROW NUMBER

TECHNOLOGY

ALTUS STEP ROW NUMBER brings the best solution for signage and safety for crowded places of low visibility as cinemas, theaters, corridors, offices, etc. The illuminated numbered profiles are very bright and have power below 0,7W. The profile is of a simple but robust construction of one piece, designed to bear burden up to 200 kg over its metallic frame. STEP ROW NUMBER profile is available in black or white as standard, other profile colours are available upon request. The fixture is available in ECO and ECO+ versions. ECO+ version provides greater brightness, when required by the customer. Profile design is engraved by high quality laser. It is possible to engrave any type of number, letters or anagrams.

5Years

Guarantee

APPLICATION

PRODUCT DESCRIPTION

Best solution for corridors and number signage and safety.

Weight support up to 150 kg/m2

High efficiency LED technology. Between 50 and 90 Lm/W depending on colour

Available in red, green, blue, amber and white

Available in 4000K-5500K

Operating temperature between -20°C and +55°C

Standard fastening with M5 screws

Life-time exceeds 50.000 hrs

Laser engraving of number, letters or anagrams

High visibility in unlighted places

ALTUS STEP ROW NUMBER - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

161


ALTUS LIGHT ENGINES IMPROVING

STEP ROW NUMBER

TECHNOLOGY TECHNICAL DATA

DIMENSIONS

70

SELV voltage < 50v

40

Available in red, green, blue, amber and white

Individually supplied, minimum 50 units

OEM paint possibility, matt or gloss

LED life-time exceeds 50.000 hrs

Coated PCB for moisture protection

Consumption < 1W at 12V

Sharp and high visibility engrave

Slim profile (ideal for emergency signage)

Dimmable by PWM dimmers

10

70

5 years guarantee

40

SPECIFIC TECHNICAL DATA

E

Code 31.65.0501 31.65.0502 31.65.0503 31.65.0504 31.65.0505 31.65.0506 31.65.0507 31.65.0508 31.65.0509 31.65.0510

In Voltage tp=65ºC (mA) Colour (Vcc) R: R: B: B: G: G: A: A: W: W:

12 12 12 12 12 12 12 12 12 12

20 15 20 15 20 15 05 15 05 15

E+ :

: ECO

LED 3 6 3 6 3 6 3 6 3 6

Light P=W Eco Eco+ Eco Eco+ Eco Eco+ Eco Eco+ Eco Eco+

R: Red / B: Blue / G: Green / A: Amber / W: White

0,25 0,50 0,25 0,50 0,25 0,50 0,25 0,50 0,25 0,50

Code 31.65.0551 31.65.0552 31.65.0553 31.65.0554 31.65.0555 31.65.0556 31.65.0557 31.65.0558 31.65.0559 31.65.0560

ECO+

In Voltage tp=65ºC (mA) Colour (Vcc) R: R: B: B: G: G: A: A: W: W:

24 24 24 24 24 24 24 24 24 24

20 15 20 15 20 15 05 15 05 15

LED 3 6 3 6 3 6 3 6 3 6

Light P=W Eco Eco+ Eco Eco+ Eco Eco+ Eco Eco+ Eco Eco+

0,50 1,00 0,50 1,00 0,50 1,00 0,50 1,00 0,50 1,00

R: Red / B: Blue / G: Green / A: Amber / W: White

ALTUS STEP ROW NUMBER - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

162


ALTUS LIGHT ENGINES IMPROVING

STEP ROW NUMBER

TECHNOLOGY INSTALLATION AND CONNECTION

2

1

Place profile on desired wall or step. Through profileâ&#x20AC;&#x2122;s

Drill on the spotted marks.

holes, make a mark on the wall or step, to use as reference.

(*) Optional: use silicon glue between the wall or step and profile for greater attachment.

3

4 +

Place and press profile and tight the screws

Connect positive (+, red) and negative (-, black) wires to

(*) Accessory: M5 black matte screws.

appropriate voltage 12/24 Vcc.

5

Number profile is utterly installed. (*) Max. 500 mm wire. ALTUS STEP ROW NUMBER - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

163


ALTUS LIGHT ENGINES IMPROVING

TECHNOLOGY

STEP ROW NUMBER

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER STEP ROW NUMBER must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (group of modules) or emergency lighting. ISOLATION STEP ROW NUMBER functions with SELV voltage, does not require active isolation of the components. It is not necessary earth connection on all conductive components of the fixture or light engine. ESD – STATIC ELECTRICITY INFORMATION STEP ROW NUMBER contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. STEP ROW NUMBER must be perfectly placed (and/ or stick) on the lighting device, profile or base for a proper connection between modules and power source, respecting its nominal values. I+D LED S.L. is not responsible for occasional module fall. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs and electronic components. Signage profile is delivered with 2 pre-made countersink and through-holes. Maximum torque for fixing recommended 5 Nm to avoid mechanical stress. TEMPERATURE ALTUS LIGHT ENGINES and STEP ROW NUMBER life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. OPTICAL CHARACTERISTICS + CCT Measurement of LED discrete points may have variations in regards on the CCT temperature here described, with a variance of 3SDCM and 2SDCM for white and +/- 5nm for coloured LEDs.

ALTUS STEP ROW NUMBER - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

164


ALTUS LIGHT ENGINES IMPROVING

STEP PROFILE KAV

TECHNOLOGY

STEP PROFILE KAV brings the best solution for signage and safety for crowded places of low visibility as cinemas, theaters, corridors, etc. The illuminated step profiles are very bright and have power below 3W per metre. The profile is of a simple but robust construction, designed to bear burden up to 300 kg per square metre. The profile is finished in black anodized, which keeps the step in good conditions regardless the high transit. STEP PROFILE KAV is available in different lengths and LED quantities under request. The step profile has anti-slip system to avoid falls or tumbles. The profile can be illuminated both up and down the step edge depending on customer requirements.

5Years

Guarantee

PRODUCT DESCRIPTION

APPLICATION

Best solution for signage and safety

Designed for high transit

Anti-spill and anti-leak

Weight support up to 300 kg/m2

High efficiency LED technology. Between 50 and 90 Lm/W depending on colour.

ALTUS LIGHT ENGINES STEP PROFILE KAV - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

Available in red, green, blue, amber and white

Available in 4000K-5500K

Operating temperature between -20°C and +45°C

Standard fastening with M5 screws

Life-time exceeds 50.000 hrs

Protector profile for LED strips

Customized length OEM

5 years guarantee

165


ALTUS LIGHT ENGINES IMPROVING

TECHNOLOGY

STEP PROFILE KAV

Anti-slip system No rubber, low maintenance

SELV security voltage < 48V

Available in blue, red, green, amber and white

Supplied per linear metre

OEM cutting possibilities (0,3 - 2 m)

LED life-time exceeds 50.000 hrs

Up to 6 m continuous (under request)

Coated PCB for moisture protection of high quality FR4

Reduced consumption < 1.8w /m (15 LEDs/m)

Spotlight lighting, ideal for emergency signs/fixtures

PWM dimmable

87.44

40.81

DIMENSIONS

6.04

TECHNICAL DATA

64

Optional, we can offer a brightness dimmer for the profile diffusor. This system allows reflex reduction on the screen.

ALTUS LIGHT ENGINES STEP PROFILE KAV - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

166


ALTUS LIGHT ENGINES IMPROVING

STEP PROFILE KAV

TECHNOLOGY SPECIFIC TECHNICAL DATA

UD:UP-DOWN

U :UP

D:DOWN

(*) OEM CUTTING LENGHTS FROM 0.3 M TO 2 M

Code

Power Colour (Vcc)

31.65.0101 31.65.0102 31.65.0104 31.65.0105 31.65.0107 31.65.0108 31.65.0110 31.65.0111 31.65.0113 31.65.0114 31.65.0116 31.65.0117 31.65.0119 31.65.0120 31.65.0122 31.65.0123 31.65.0125 31.65.0126 31.65.0128 31.65.0129 31.65.0131 31.65.0132 31.65.0134 31.65.0135 31.65.0137 31.65.0138 31.65.0140 31.65.0141 31.65.0143 31.65.0144

R:

R: R: R: R: B: B: B: B: B: B: G: G: G: G: G: G: A: A: A: A: A: A: W: W: W: W: W: W: R:

12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12

In/m tp=65ยบC (mA) 15 45 15 45 30 90 15 45 15 45 30 90 15 45 15 45 30 90 15 45 15 45 30 90 15 45 15 45 30 90

LED/ m Light P=W 15 45 15 45 15 45 15 45 15 45 15 45 15 45 15 45 15 45 15 45 15 45 15 45 15 45 15 45 15 45

U UD D U UD D U UD D U UD D U UD D U UD D U UD D U UD D U UD D U UD D

1,8 10,8 1,8 5,4 3,6 5,4 1,8 10,8 1,8 5,4 3,6 5,4 1,8 10,8 1,8 5,4 3,6 5,4 1,8 10,8 1,8 5,4 3,6 5,4 1,8 10,8 1,8 5,4 3,6 5,4

R: Red / B: Blue / G: Green / A: Amber / W: White

Code 31.65.0301 31.65.0302 31.65.0304 31.65.0305 31.65.0307 31.65.0308 31.65.0310 31.65.0311 31.65.0313 31.65.0314 31.65.0316 31.65.0317 31.65.0319 31.65.0320 31.65.0322 31.65.0323 31.65.0325 31.65.0326 31.65.0328 31.65.0329 31.65.0331 31.65.0332 31.65.0334 31.65.0335 31.65.0337 31.65.0338 31.65.0340 31.65.0341 31.65.0343 31.65.0344

Power Colour (Vcc) R: R: R: R: R: R: B: B: B: B: B: B:

G: G: G: G: G: G: A: A: A: A: A: A:

W: W: W: W: W: W:

24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24

In/m tp=65ยบC (mA) 15 45 15 45 30 90 15 45 15 45 30 90 15 45 15 45 30 90 15 45 15 45 30 90 15 45 15 45 30 90

LED/ m Light P=W 15 45 15 45 15 45 15 45 15 45 15 45 15 45 15 45 15 45 15 45 15 45 15 45 15 45 15 45 15 45

U UD D U UD D U UD D U UD D U UD D U UD D U UD D U UD D U UD D U UD D

3,6 10,8 3,6 10,8 7,2 10,8 3,6 21,6 3,6 10,8 7,2 10,8 3,6 21,6 3,6 10,8 7,2 10,8 3,6 21,6 3,6 10,8 7,2 10,8 3,6 21,6 3,6 10,8 7,2 10,8

R: Red / B: Blue / G: Green / A: Amber / W: White

(*) Si desea el atenuador de brillo sobre el difusor, agregue una letra V al final del codigo. Ejemplo: 31.65.0101V

ALTUS LIGHT ENGINES STEP PROFILE KAV - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

167


ALTUS LIGHT ENGINES IMPROVING

STEP PROFILE KAV

TECHNOLOGY

INSTALLATION AND CONNECTION EXAMPLE

2

1

Place profile on desired step. Through profileâ&#x20AC;&#x2122;s holes,

Drill on the spotted marks.

make a mark on the step, to use as reference.

(*) Optional: use silicon glue between the step and profile for greater attachment.

3

4

+

-

Place and press profile and tight the screws

Connect positive (+, red) and negative (-, black) wires to

(*) Accessory: M5 black matte screws.

appropriate voltage 12/24 Vcc.

5

Profile is utterly installed. (*) Max. 500 mm wire.

ALTUS LIGHT ENGINES STEP PROFILE KAV - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

168


ALTUS LIGHT ENGINES IMPROVING

TECHNOLOGY

STEP PROFILE KAV

SECURITY AND INSTALLATION INFORMATION ELECTRICAL POWER STEP PROFILE KAV must be feed at constant current; the energy source power must be in accordance with the quantity of connected modules for proper functioning of the module (group of modules) or emergency lighting. ISOLATION STEP PROFILE KAV functions with SELV voltage does not require active isolation of the components. It is not necessary earth connection on all conductive components of the fixture or light engine. ESD – STATIC ELECTRICITY INFORMATION STEP PROFILE KAV contains electronic components which are very sensible to static electricity. In this respect is it highly recommendable to always manipulate the items with appropriate ESD protection, and take adequate measures for safety matters. If you need further information please refer to our webpage www.idled.eu. MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. STEP PROFILE KAV must be perfectly placed (and/or stick) on the lighting device, profile or base for a proper connection between modules and power source, respecting its nominal values. I+D LED S.L. is not responsible for occasional module fall. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs and electronic components. Signage profile is delivered with 3 pre-made holes per metre of D=5 mm countersink and through-hole. Maximum torque for fixing recommended 5 Nm to avoid mechanical stress TEMPERATURE ALTUS LIGHT ENGINES and STEP PROFILE KAV life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee. OPTICAL CHARACTERISTICS + CCT Measurement of LED discrete points may have variations in regards on the CCT temperature here described, with a variance of 3SDCM and 2SDCM for white and +/- 5nm for coloured LEDs.

ALTUS LIGHT ENGINES STEP PROFILE KAV - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

169


ACCESORIES

170


ACCESORIES IMPROVING

TECHNOLOGY

LINK CONNECTOR B2B MODULES

LINK CONNECTORS B2B MODULES are ideal to connect linear LED modules. These connectors eliminate the use of small cable connections which are difficult to handle. Their small size (26x1mm) makes them perfect connectors for linear fixtures. Their maximum current is 6A. Easy to operate. Internally made of copper, externally plated and white PA plastic case, certified UL94. Minimum packaging of 100 units.

26 8.9

Ø1

DIMENSIONS

3Years

26 Ø1 4

8.9

Guarantee

(*) Measured in mm

SELECTION TABLE PLASTIC TYPE

CONTACTS

VOLTAGE (V)

MAX. CURRENT (A)

OPERATING TEMPERATURE (•C)

PACKAGING (UNITS)

1 A POLE 31.70.06.345.1P.A

UL 94:V-2 WHITE

PLATED COPPER

600 EN60598

6

-30+85

250

1 B POLE 31.70.06.345.1P.B

UL 94:V-2 WHITE

PLATED COPPER

600 EN60598

6

-30+85

1500

2 A POLES 31.70.06.345.2P.A

UL 94:V-2 WHITE

PLATED COPPER

250 EN60598

6

-30+85

500

2 B POLES 31.70.06.345.2P.B

UL 94:V-2 WHITE

PLATED COPPER

250 EN60598

6

-30+85

100

CODE

LINK CONNECTOR B2B MODULES - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

171


ACCESORIES IMPROVING

TECHNOLOGY (*) ESD protection to earth connection

1

LINK CONNECTOR B2B MODULES

3 4.4 mm - 5.4 mm

J Place link connector in the LED module.

Place the next LED module on the other side of the

Protect and connect yourself with ESD (*) earth connection

connector, and allow a distance of minimum 4.4 mm

systems.

and maximum 5.4 mm between the LED modules.

2

Join together all necessary modules.

INSTALLATION AND SECURITY INFORMATION MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. LINK CONNECTOR B2B MODULES must be perfectly placed between the PCBs to keep optimal properties during life-time. LINK CONNECTOR B2B MODULES are not approved to be placed on SMD push in type connectors that are not in good conditions and perfectly clean. I+D LED S.L. in any case accepts responsibility over occasional loss of property, product damage, and damage caused t third parties. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs and electronic components. This product packaging is available in bags of 100-250-500-1500 units. TEMPERATURE LINK CONNECTOR B2B MODULES’ life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee.

LINK CONNECTOR B2B MODULES - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

172


ACCESORIES IMPROVING

TECHNOLOGY

DOUBLE TAPE BOND 4965

Double sided adhesive tape ideal for joining LED modules or similar up to 20-25W per meter. Suitable for linear and flexible applications. This tape fits well for both raw aluminum and epoxy coated aluminum. Easy to operate. Tapes are transparent and made of acrylic. Minimum packaging available of 25 m. Adhesive properties improve with time. Appropriate for high requirement applications, mechanical handling or critical materials.

SPECIFIC TECHNICAL DATA

ADHESION CODE

31.70.4965.9.01

STEEL (N/cm)

AL (N/cm)

PMMA (N/cm)

PET (N/cm)

CRISTAL (N/cm)

11.8

10.6

10.6

9.5

11

PAINT THERMAL COLOUR THICKNESS ADHESIVE R a T R a H (N/cm) RESISTANCE (um) TYPE (â&#x20AC;¢C)(**) (***) (W/Mk) (*) 12.5

>0.15

TRANSP

205

SOLID ACRYLIC

>80

HIGH

(*) Thermal resistance (**) Temperature resistance (***) Humidity resistance

INSTALLATION

2

1

Remove transparent film from the adhesive tape.

Make sure that the surface on which the tape will be applied is clean. Place the tape on the desired surface; apply moderate pressure for few seconds and release. (Keep in mind not pressing too much if there are electronic components on the other side of the PCB).

DOUBLE TAPE BOND 4965 - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

173


ACCESORIES IMPROVING

TECHNOLOGY

3

DOUBLE TAPE BOND 4965

(*) ESD protection to earth connection

4

Remove top film.

J

Place the LED stripe on top of the tape and apply pressure on both stripe ends, paying special attention that no component will be damaged. Always manipulate the items with appropriate ESD protection for safety matters.

INSTALLATION AND SECURITY INFORMATION MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the product installation. TAPE BOND 4965 must be perfectly placed on the surface to guarantee its long term properties, life-time and thermal interface. The tape does not grant its adherence qualities if not applied on flat and clean surfaces. I+D LED S.L. in any case accepts responsibility over occasional quality losses, product damage, and damage caused by third parties. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs. TAPE BOND 4965 is supplied in 25m-long reels. TEMPERATURE TAPE BOND 4965 life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep productâ&#x20AC;&#x2122;s guarantee.

DOUBLE TAPE BOND 4965 - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

174


ACCESORIES IMPROVING

TECHNOLOGY

DOUBLE TAPE BOND 7054

Double sided adhesive tape ideal for joining LED modules or similar up to 20-25W per meter. Suitable for linear and flexible applications. This tape fits well for both raw aluminum and epoxy coated aluminum. Easy to operate. Tapes are transparent and made of acrylic. Minimum packaging available of 25 m. Adhesive properties improve with time. Appropriate for high requirement applications, mechanical handling or critical materials.

SPECIFIC TECHNICAL DATA

ADHESION CODE

9MM 31.70.7054.9.01

STEEL (N/cm) 19

19 12MM 31.70.7054.12.01 N/cm

AL (N/cm)

PMMA (N/cm)

PET (N/cm)

CRYSTAL (N/cm)

10.6

12

12

17

6

>0.2

TRANSP

500

10.6 N/cm

12 N/cm

12 N/cm

17 N/cm

6 N/cm

>0.2 W/Mk

TRANSP

500 um

(*) Thermal resistance (**)Temperature resistance (***)Humidity resistance

PAINT THERMAL COLOUR THICKNESS ADHESIVE R a T (N/cm) RESISTANCE (um) TYPE (โ€ขC) (W/Mk) (*) (**)

RaH (***)

>80

VERY HIGH

SOLID ACRYLIC

SOLID >80 ยบ C VERY ACRYLIC HIGH

INSTALLATION

2

1

Remove transparent film from the adhesive tape.

Make sure that the surface on which the tape will be applied is clean. Place the tape on the desired surface; apply moderate pressure for few seconds and release. (Keep in mind not pressing too much if there are electronic components on the other side of the PCB).

DOUBLE TAPE BOND 7054 - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

175


ACCESORIES IMPROVING

TECHNOLOGY

DOUBLE TAPE BOND 7054

(*) ESD protection to earth connection

3

4

J

Place the LED stripe on top of the tape and apply pressure on Remove top film.

both stripe ends, paying special attention that no component will be damaged. Always manipulate the items with appropriate ESD protection for safety matters.

SECURITY AD INSTALLATION INFORMATION MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the product installation. TAPE BOND 7054 must be perfectly placed on the surface to guarantee its long term properties, life-time and thermal interface. The tape does not grant its adherence qualities if not applied on flat and clean surfaces. I+D LED S.L. in any case accepts responsibility over occasional quality losses, product damage, and damage caused by third parties. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs and electronics components. TAPE BOND 7054 is supplied in 25m-long reels. TEMPERATURE TAPE BOND 7054 life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep productâ&#x20AC;&#x2122;s guarantee.

DOUBLE TAPE BOND 7054 - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

176


ACCESORIES IMPROVING

CONNECTION BOX BOXCON 12-48V / 28 OUTPUTS

TECHNOLOGY

The BOXCON is ideal for connecting several devices in parallel with stable constant current power supply voltages up to 50V. It has 28 outputs to connect 1 mm cables. BOXCON uses quick connectors, push in type for power input with wire length up to 1.5 mm. It eliminates the need to use crimp connectors and wire to wire housing. BOXCON optimizes connection time. It has a maximum current of 6 A.

DIMENSIONS 157

3Years

75

Guarantee

(*) Measured in mm

SELECTION TABLE CODE

PLASTIC TYPE

CONTACTS

VOLTAGE (V)

MAX. CURRENT (A)

OPERATING TEMPERATURE (โ€ขC)

PACKAGING MOQ (UNITIES)

31.70.001

V-0 UL94

SILVER PLA

50 MAX.

6

55ยบC

1-5

CONNECTION BOX BOXCON 12-24V/28OUTPUTS - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

177


ACCESORIES IMPROVING

TECHNOLOGY

CONNECTION BOX BOXCON 12-48V / 28 OUTPUTS

INSTALLATION AND CONNECTION EXAMPLE (*) ESD protection to earth connection

1

J

2

12-24 V

12-24 V

Introduce luminaire wire in the Push-In connector, pressing

Place the power supply wires inside the main board

slightly the connector’s flap as shown in the above image.

connectors as shown in the above image. Repeat to connect

Protect and connect yourself with ESD (*)

many BOXCON with each other. Check cables polarity in detail to avoid short circuits or devices malfunction.

SECURITY AND INSTALLATION INFORMATION MOUNTING AND INSTALLATION I+D LED S.L. is not responsible for the installation of the product. BOXCON must be perfectly placed and attached (and/or stick) on the desired spot isolated from conductive components. I+D LED S.L. is not responsible for occasional damage, break, short circuit or related malfunction derived from unappropriated installation or connection of the wires and its polarities. If any type of chemical substance is used during the assembly of the luminaire or light engine, it must not have any type of curing by means of gas condensation; as these chemical substances may damage the LEDs and electronic components. The module will be delivered in individual boxes. TEMPERATURE BOXCON life-time depends to a great extent on operating temperature. Under no circumstance temperature should exceed the maximum permissible (Tc=55°C) limit here indicated. Exposure to higher temperatures might affect its long term proper functioning. Room temperature must be measured under worst-case conditions to ensure life-time and keep product’s guarantee.

CONNECTION BOX BOXCON 12-24V/28OUTPUTS - V.1.1_ES - www.idled.eu All rights reserved. This publication may be modified without prior notice.

178


PRODUCT CATALOG I+D LED V18.01  

Data Sheet.

PRODUCT CATALOG I+D LED V18.01  

Data Sheet.

Advertisement