ECET 365 Week 2 Quiz Click Here to Buy the Tutorial http://www.tutorialrank.com/ECET/ECET-365-DEVRY/product-8249-ecet-365week--2-quiz-devry For more course tutorials visit www.tutorialrank.com Tutorial Purchased: 4Times, Rating: A

1.

Question (TCO #5) Identify the step size for an 8-bit analog-to-digital converter with Vref= : 2.5 VDC?

Student Answer: 10 millivolts 25 millivolts 4.9 millivolts 5 volts Comments:

2. Question : (TCO # 5) How many steps are available with a 10-bit ADC? Student Answer: 10 1024 512 256 Comments:

3.

Question (TCO #5) What is the cutoff frequency for a low-pass filter with a resistor R = : 3000 and a capacitor C = .01 Âľf?

Student Answer: f = 5.3 KHz f = 3300 Hz f = 120 KHz f = 6 KHz Comments:

4.

Question (TCO #5)A band-stop filter is a filter that _____ frequencies below low-limit and : above high-limit frequencies and _____ frequencies between the limits.

Student Answer: blocks; blocks passes; blocks blocks; passes has; blocks Comments:

5.

Question (TCO #5) A bridge with R1= 5.1 K, R2= 2 K, and R3= 15 K can be at null if R4is : _____.

Student Answer: 10.5 K 5.88 K 588 1K Comments:

(TCO #5) An instrumentation amplifier with two buffers has a feedback resistor of 100 K. The two resistors from the buffer's output to the input of the last stage OPQuestion 6. Amp are 1 K resistors. Voltage levels to the non-inverting buffer inputs. Voltage : levels to the non-inverting buffer inputs are V1= .06 volt and V2= .02 volts. What is Voutof the instrumentation amplifier? Student Answer: 4 Volts

20.4 Volts 3.3 Volts 15.3 Volts Comments:

(TCO #5) An embedded system with an 8-bit analog-to-digital converter is connected to a transducer with an output voltage of 10 millivolts. This signal is Question 7. amplified by an amplifier with a gain of 25. Assume that this signal level is : appropriate for the ADC input. If the reference voltage of the ADC converter is 5 volts, what will be the output of the ADC in binary form? Student Answer: 01100110 00110011 00001101 01111011 Comments:

8.

Question (TCO #5) An 8-bit analog-to-digital converter has maximum output voltage of 2.5 : VDC. What is the reference voltage to this ADC?

Student Answer: 2.5 VDC 5 VDC 1.25 VDC None of the above Comments:

9.

Question (TCO #5) A well-behaved analog signal with a frequency of 20 kHz is being : sampled. What is the sampling frequency if frequency aliasing occurs?

Student Answer: 90 kHz 40 kHz 85 kHz

60 khz Comments:

10. Question : (TCO #5) To model a nonlinear transducer, one can _____. Student Answer: use empirically determined nonlinear equation use a piecewise linear system use a lookup table located in memory All of the above

Ecet 365 week 2 quiz

ECET 365 Week 2 Quiz ECET 365 Lab 6 Servo Motor Interfaces-Closed-Loop Motor Speed Control ECET 365 Lab 5 Servo Motor Interfaces-Closed-Loop...

Ecet 365 week 2 quiz

Published on Feb 4, 2014

ECET 365 Week 2 Quiz ECET 365 Lab 6 Servo Motor Interfaces-Closed-Loop Motor Speed Control ECET 365 Lab 5 Servo Motor Interfaces-Closed-Loop...

Advertisement