Page 1

REMOTE CONTROL PROGRAMMING Locate the program switch under the access panel on the front of the Remote Control module as shown below (Fig. 1).

Fig. 2

Remove access panel

Program Switch (SW1)

Program LED

Transmitter LED

Fig. 1

Button 1

Fig. 3

Read through the steps below BEFORE you begin. You will have 10 seconds to complete the programming sequence.

1. Push the program switch (SW1) (Fig. 2) until the red program LED lights solid, then release switch. 2. Push button 1 on the remote transmitter until the program LED goes out (Fig. 3). 3. Push button 1 on the transmitter again, the program LED should flash slowly ... now release button. 4. Remote is now programmed. Test unit. NOTE: If the remote does not work, make sure that the transmitter LED is flashing when button 1 is pressed, and that the battery is good. Repeat steps 1-4. 5. Repeat steps 1-4 for second transmitter. CMRCP_v3.0


CABLEMASTER REMOTE CONTROL WIRING DIAG WHITE

OUT

UNIT - #1 (Channels 1 & 2)

RED

OFF

BLACK

POWER SWITCH

CABLEMASTER RELAY ASSEMBLY # 04034 - (12, 24 volt DC) 12/24 Power DC Input Switch RED Pos. + Red 1

BATERY POSITIVE (+)

(see note -1)

IN

(Remote - Red)

(Remote - RED)

BATTERY NEGATIVE (-)

Neg. -

(Remote - BLACK)

White 2

WHITE

(Remote - Yellow)

Black 3

BLACK

(Remote - Green)

(Rmt - Yellow or Purple)

(Rmt - Green or Tan)

(Remote - Black)

M

Motor Output

ORANGE

Orange

BLACK

Black

IN 4 Limit Switch 5

IN-LIMIT SWITCH

OUT 6 Limit Switch 7

12v DC use 20 amp breaker 24v DC use 15 amp breaker

12 or 24vdc MOTOR

OUT-LIMIT SWITCH

GLENDINNING MARINE PRODUCTS, INC. Conway, SC 843-399-6146

(see note -2)

NOTE: With the new relay assembly a 12VDC Remote Control is required to be used for all voltages (12 or 24 VDC) (Remote - Black)

(if operating 2 Cablemasters) WHITE

POWER SWITCH

(Remote - RED)

Neg. -

BATTERY NEGATIVE (-)

(Remote - BLACK)

WHITE

(Remote - Purple)

Black 3

BLACK

(Remote - Tan)

(Rmt - Green or Tan)

Motor Output

M

White 2

(Rmt - Yellow or Purple)

ORANGE BLACK

Orange Black

IN 4 Limit Switch 5

12v DC use 20 amp breaker 24v DC use 15 amp breaker

12,24 v MOTOR

IN-LIMIT SWITCH

OUT 6 Limit Switch 7

GLENDINNING MARINE PRODUCTS, INC. Conway, SC 843-399-6146

( -- )

IN

12 VDC

BATERY POSITIVE (+)

OFF

BLACK

CABLEMASTER RELAY ASSEMBLY # 04034 (12, 24 volt DC) 12/24 Power DC Input Switch RED Pos. + Red 1

(see note - 1)

OUT

RED

REMOTE CONTROL

UNIT - #2 (Channels 3 & 4)

(+)

OUT-LIMIT SWITCH

(see note - 2)

Note: 1.) Connect battery positive lead via fuse or circuit breaker. See Installation Manual for rating. Circuit Breaker Specs.: CM7 - 12 Volt 20 Amp Breaker 8-10 Running Amps CM7 - 24 Volt 15 Amp Breaker 5-6 Running Amps 2.) For low profile Cablemaster installation, the motor leads must be reversed for correct limit switch operation. See manual for more information. 95405_Remote_Wire.cad

Version - T41304 / 2

IN

REMOTE KEY PAD

OUT

Channel #1

Channel #2

Channel #3

Channel #4

/Cablemaster%20CM_-_Remote_Control_Programing  

http://glendinninginc.com/gmp/pdf/cablemaster/cm-models/Cablemaster%20CM_-_Remote_Control_Programing_Guide.pdf

Read more
Read more
Similar to
Popular now
Just for you