Gilmore Regulator Valve Catalog

Page 1

REGULATOR VALVE

CATALOG


Table of Contents

Regulator Valve

Gilmore produces the most reliable flow control solutions across the globe, even in extreme habitats, we provide definitive downhole solutions with optimal performance in both topside and subsea applications.

Gilmore continues to demonstrate precision in performance and reliability with this line of pressure regulator valves by improving cycle life and performance in critical offshore subsea applications. 1” Pressure Regulator Valve I Manual Spring • • •

Connections NPT / SAE/ Code 62 / Sealsub Mounted Set Point Pressure 500-1500 psi 1000-2500 psi 1500-3500 psi 2000-4500 psi 2500-5500 psi Max Flow Capacity Single Inlet: 150 GPM Dual Inlets: 300 GPM

1” Pressure Regulator Valve I Hydraulic Pilot • • •

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-02

Connections NPT / SAE/ Code 62 / Sealsub Mounted Set Point Pressure 300-5000 psi Max Flow Capacity Single Inlet: 150 GPM Dual Inlets: 300 GPM


Table of Contents (CONT.)

Regulator Valve

1” Pressure Regulator Valve I Air Motor • • •

Connections NPT / SAE/ Code 62 Set Point Pressure 500-1500 psi 1000-2500 psi 1500-3500 psi 2000-4500 psi 2500-5500 psi Max Flow Capacity Single Inlet: 150 GPM Dual Inlets: 300 GPM

1” Pressure Regulator Valve I Compensator • • •

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-03

Connections SAE / Others Available upon Request Set Point Pressure 1500-3500 psi Others Available upon Request Max Flow Capacity Dual Inlets: 300 GPM Others Available upon Request


Reference Sheet

Regulator Valve

2.

3.

1.

4.

8.

6. 5.

Figure 1: Hydraulic Pilot Dual Inlet Pressure Regulator

Gilmore’s pressure regulators are the ideal solution for maintaining and limiting downstream pressure. Hardened stainless steel or Tungsten Carbide shear seals are precision lapped to provide a resilient seal and develop a wiping action that resists contamination and leaking. 1. Supply Pressure – The maximum inlet pressure the regulator is designed for. 2. Regulated Pressure – The downstream pressure the regulator sustains to supply or vent hydraulic fluid. 3. Set Point Range – The lowest and highest regulated pressure the valve can achieve. The set point is typically determined by the size of the spring or ratio of the hydraulic plunger. 4. Deadband – The difference in pressure for the regulator to overcome the static friction between the closed, open, and venting positions. 5. Lowest Regulated Pressure – The minimum pressure outside of the set point range in which the regulator will still function. The capacity of the regulator maybe diminished at this point. 6. Hydraulic Damping – Patented feature of the regulator that reduces dynamic instability. (Chattering) 7. Auxiliary Connections – Ports in the regulator that allow for gauge pressure installation or additional accumulated volume. 8. Refined Tungsten Carbide Trim – Patented technology that reduces the amount of tungsten carbide used in the regulator therefore, reduces costs. INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-04

7. Figure 2: Manual Spring Pressure Regulator


Technical Sheet

Regulator Valve

Pressure Regulator Manual Spring Dual Inlets 3500/6000 PSI

FUNCTIONAL DESIGN SPECIFICATION

2X VENT 2X INLET

REGULATED GAGE

Available Configurations: NPT, SAE, Code 62, Seal Sub Mounted

Maximum Inlet Pressure Pressure

6,000 PSI

Fully Open Flow Coefficient (Cv) Regulated

14

Fully Open Flow Coefficient (Cv) Vent

2

Set Point Range

3,500 - 1,500 PSI

Typical Deadband at 5000 PSI Supply

300 + 100 PSI

Typical Deadband at 3000 PSI Supply

200 + 50 PSI

Fully Open Max Regulated Flow Rate

250 GPM

Predicted Cycle Life

10,000 Cycles

Operating Temperature Range

32˚F to 150˚F

Storage Temperature Range

32˚F to 150˚F

Acceptable Operating Fluid Types

Water or mineral oil-based control fluid

Mounting Restrictions

None

US Patent

10,739,796

BILL OF MATERIALS

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-05

Item Number*

Description

Material

1

BODY, 1” OUTLET FLANGE

A564 TP 630 (17-4 PH)

2

FLANGE BOTTOM

A276 TP 316

3

GUIDE, PLUNGER, 1-1/2”

A276 TP 316

4

ADAPTER, SPRING HOUSING

A276 TP S21800 (NITRONIC 60)

5

HOUSING, SPRING

A276 TP 316

6

CAP, SPRING HOUSING

A276 TP S21800 (NITRONIC 60)

7

NUT, O-LOCK

A276 TP 316

8

CAP, LOCK

A276 TP 316

9

INSERT, FLOW PORT, SUPPLY AND VENT

TUNGSTEN CARBIDE / NICKEL

10

CARRIER, SEAL

A276 TP S21800 (NITRONIC 60)

11

PLUNGER, 1-1/2”

A276 TP S21800 (NITRONIC 60)

12

RING, SEAL, SUPPLY

TUNGSTEN CARBIDE / NICKEL

Continued on page 5.1


Technical Sheet

Regulator Valve

Pressure Regulator Manual Spring Dual Inlets 3500/6000 PSI

BILL OF MATERIALS (CONT.)

2X VENT 2X INLET

REGULATED GAGE

Available Configurations: NPT, SAE, Code 62, Seal Sub Mounted

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-05.1

Item Number*

Description

Material

13

RING, SEAL, VENT

TUNGSTEN CARBIDE / NICKEL

14

WAVE SPRING

AMS5699 (X-750)

15

SPRING, COMPRESSION

AMS5699 (X-750)

16

SCREW, ADJUSTING, VALVE

F593 GR2 (T316)

17

PLATE, SPRING

A276 TP 316

18

PLUG, HEX, /8” SAE

A240 TP 316

19

PELLET, NYLOK

20

HOLLOW HEX PLUG, /2”

A240 TP 316

21

RING, BACKUP

PEEK

22

WIPER, D-STYLE, 1.500 PLUNGER

POLYURETHANE

23

WEAR BAND, PLUNGER, 1-1/2”

DELRIN AF

24

SHCS, THREAD-LOCKING, 1/4-20 UNC X 1/2” LONG

F593 GR2 AND NYLON

25

SHCS, 3/8-16 UNC X 1-1/2” LONG

A286 GR 660

26

SHCS, 3/8-16 UNC X 1-1/4” LONG

A286 GR 660

27

SHCS, 5/16-18 UNC X 3/4” LONG

A286 GR 660

28

WEAR BAND, SEAL CARRIER

DERIN AF

29

T-SEAL, ROD

CARBOXYLATED NITRILE / NYLATRON

30

WEAR BAND

DELRIN AF

31

SPRING, COMPRESSION

A313 TP 316

32

FLANGE, INLET, 1- /2” C62

A276 TP 316

33

FLANGE, INLET, 1” C62

A276 TP 316

34

SPRING, COMPRESSION

INCONEL X750

35

BALL

A276 TP 316

36

O-RING (ITEM* 36-41)

HNBR

42

RING, BACKUP (ITEM* 42-44)

PEEK

Continued on page 5.2

3

NYLON 1

1


Technical Sheet

Regulator Valve

Pressure Regulator Manual Spring Dual Inlets 3500/6000 PSI

Part Numbers

Description

29090

Valve, Pressure Regulator, Manual Spring, 3500-1500 psi range, Code 62 Ports, Dual Inlets

29134

Valve, Pressure Regulator, Manual Spring, 4500-2000 psi range, Code 62 Ports, Dual Inlets

2X VENT 2X INLET

REGULATED GAGE

Available Configurations: NPT, SAE, Code 62, Seal Sub Mounted

*The repair kit part number will match the category part number with (RK) at the end.

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-05.2

*The seal kit part number will match the category part number with (SK) at the end.


Technical Sheet

Regulator Valve

Pressure Regulator Manual Spring Dual Inlets 3500/6000 PSI

FUNCTIONAL DESIGN SPECIFICATION

2X VENT 2X INLET

REGULATED GAGE

Available Configurations: NPT, SAE, Code 62, Seal Sub Mounted

Maximum Inlet Pressure Pressure

6,000 PSI

Fully Open Flow Coefficient (Cv) Regulated

14

Fully Open Flow Coefficient (Cv) Vent

2

Set Point Range

3,500 - 1,500 PSI

Typical Deadband at 5000 PSI Supply

300 + 100 PSI

Typical Deadband at 3000 PSI Supply

200 + 50 PSI

Fully Open Max Regulated Flow Rate

250 GPM

Predicted Cycle Life

10,000 Cycles

Operating Temperature Range

32˚F to 150˚F

Storage Temperature Range

32˚F to 150˚F

Acceptable Operating Fluid Types

Water or mineral oil-based control fluid

Mounting Restrictions

None

US Patent

10,739,796

BILL OF MATERIALS

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-06

Item Number*

Description

1

BODY

2

FLANGE BOTTOM, /8”

A276 TP 316

3

GUIDE, PLUNGER, 1- /2”

A276 TP 316

4

ADAPTER, SPRING HOUSING

A276 TP S21800 (NITRONIC 60)

5

HOUSING, SPRING

A276 TP 316

6

CAP, SPRING HOUSING

A276 TP S21800 (NITRONIC 60)

7

NUT, O-LOCK

A276 TP 316

8

CAP, LOCK

A276 TP 316

9

INSERT, FLOW PORT, SUPPLY AND VENT

TUNGSTEN CARBIDE / NICKEL

10

CARRIER, SEAL

A276 TP S21800 (NITRONIC 60)

11

PLUNGER, 1-1/2”

A276 TP S21800 (NITRONIC 60)

12

RING, SEAL, SUPPLY

TUNGSTEN CARBIDE / NICKEL

Continued on page 6.1

Material A564 TP 630 (17-4 PH) 3

1


Technical Sheet

Regulator Valve

Pressure Regulator Manual Spring Dual Inlets 3500/6000 PSI

BILL OF MATERIALS (CONT.)

2X VENT 2X INLET

REGULATED GAGE

Available Configurations: NPT, SAE, Code 62, Seal Sub Mounted

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-06.1

Item Number*

Description

Material

13

RING, SEAL, VENT

TUNGSTEN CARBIDE / NICKEL

14

WAVE SPRING

AMS5699 (X-750)

15

SPRING, COMPRESSION

AMS5699 (X-750)

16

SCREW, ADJUSTING, VALVE

F593 GR2 (T316)

17

PLATE, SPRING

A276 TP 316

18

PLUG, HEX, 3/8” SAE

A240 TP 316

19

PELLET, NYLOK

20

HOLLOW HEX PLUG, /2”

A240 TP 316

21

RING, BACKUP

PEEK

22

WIPER, D-STYLE, 1.500 PLUNGER

POLYURETHANE

23

WEAR BAND, PLUNGER, 1-1/2”

DELRIN AF

24

SHCS, THREAD-LOCKING, 1/4-20 UNC X 1/2” LONG

A593 T316 AND NYLON

25

SHCS, 3/8-16 UNC X 1-1/2” LONG

A286 GR 660

26

SHCS, 3/8-16 UNC X 1-1/4” LONG

A286 GR 660

27

SHCS, 5/16-18 UNC X 3/4” LONG

A286 GR 660

28

SHCS, 3/8-16 UNC X 1-5/8” LONG

A286 GR 660

29

T-SEAL, ROD

CARBOXYLATED NITRILE / NYLATRON

30

WEAR BAND

DELRIN AF

31

SPRING, COMPRESSION

A313 TP 316

32

FLANGE, INLET, RIGHT, 1 /2”

A276 TP 316

33

FLANGE, INLET, LEFT, 1 /2”

A276 TP 316

34

SPRING, COMPRESSION

INCONEL X750

35

SEAL SUB, 1”

A564 TP 630 (17-4PH)

36

SEAL SUB 1- /4”

A564 TP 630 (17-4PH)

37

BALL

A276 TP 316

Continued on page 6.2

NYLON 1

1


Technical Sheet

Regulator Valve

Pressure Regulator Manual Spring Dual Inlets 3500/6000 PSI

BILL OF MATERIALS (CONT.)

2X VENT 2X INLET

Item Number*

Description

Material

38

WEAR BAND , SEAL CARRIER

DELRIN AF

39

WASHER, NORD-LOCK, 3 /8”

254 SMO

40

O-RING (ITEM* 40-46)

HNBR

47

RING, BACKUP (ITEM* 47-51)

PEEK

Part Numbers

Description

29093

Valve, Pressure Regulator, Manual Spring, 3500-1500 psi range, Seal Sub Mounted, Dual Inlets

REGULATED GAGE

Available Configurations: NPT, SAE, Code 62, Seal Sub Mounted

*The repair kit part number will match the category part number with (RK) at the end.

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-06.2

*The seal kit part number will match the category part number with (SK) at the end.


Technical Sheet

Regulator Valve

Pressure Regulator Manual Spring Single Inlet 3500/6000 PSI

FUNCTIONAL DESIGN SPECIFICATION

VENT INLET

REGULATED GAGE

Available Configurations: NPT, SAE, Code 62, Seal Sub Mounted

Maximum Inlet Pressure Pressure

6,000 PSI

Fully Open Flow Coefficient (Cv) Regulated

7

Fully Open Flow Coefficient (Cv) Vent

1

Set Point Range

3,500 - 1,500 PSI

Typical Deadband at 5000 PSI Supply

300 + 100 PSI

Typical Deadband at 3000 PSI Supply

200 + 50 PSI

Fully Open Max Regulated Flow Rate

125 GPM

Predicted Cycle Life

10,000 Cycles

Operating Temperature Range

32˚F to 150˚F

Storage Temperature Range

32˚F to 150˚F

Acceptable Operating Fluid Types

Water or mineral oil-based control fluid

Mounting Restrictions

None

US Patent

10,739,796

BILL OF MATERIALS

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-07

Item Number*

Description

Material

1

BODY

A564 TP 630 (17-4 PH)

2

FLANGE, 1” SAE INLET, 1 /2” SAE VENT

A276 TP 316

3

FLANGE, 1” SAE REGULATED

A276 TP 316

4

FLANGE BOTTOM

5

GUIDE, PLUNGER, 1- /2”

A276 TP 316

6

ADAPTER, SPRING HOUSING

A276 TP S21800 (NITRONIC 60)

7

HOUSING, SPRING

A276 TP 316

8

CAP, SPRING HOUSING

A276 TP S21800 (NITRONIC 60)

9

NUT, O-LOCK

A276 TP 316

10

CAP, LOCK

A276 TP 316

11

INSERT, FLOW PORT, BLANK

TUNGSTEN CARBIDE / NICKEL

12

INSERT, FLOW PORT, SUPPLY AND VENT

TUNGSTEN CARBIDE / NICKEL

Continued on page 7.1

A276 TP 316 1


Technical Sheet

Regulator Valve

Pressure Regulator Manual Spring Single Inlet 3500/6000 PSI

BILL OF MATERIALS (CONT.)

VENT INLET

REGULATED GAGE

Available Configurations: NPT, SAE, Code 62, Seal Sub Mounted

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-07.1

Item Number*

Description

Material

13

CARRIER, SEAL

A276 TP S21800 (NITRONIC 60)

14

PLUNGER, 1-1/2”

A276 TP S21800 (NITRONIC 60)

15

RING, SEAL, SUPPLY

TUNGSTEN CARBIDE / NICKEL

16

RING, SEAL, VENT

TUNGSTEN CARBIDE / NICKEL

17

WAVE SPRING

AMS5699 (X-750)

18

SPRING, COMPRESSION

AMS5699 (X-750)

19

SCREW, ADJUSTING

F593 GR2 (T316)

20

PLATE, SPRNG

A276 TP 316

21

PLUG, HEX, /8” SAE

A240 TP 316

22

PELLET, NYLOK

NYLON

23

HOLLOW HEX PLUG, 1/2”

A240 TP 316

24

RING, BACKUP

PEEK

25

WIPER, D-STYLE, 1- /2” PLUNGER

POLYURETHANE

26

FLANGE, BLANK

A276 TP 316

27

WEAR BAND PLUNGER, 1-1/2”

DELRIN AF

28

SHCS, THREAD-LOCKING, 1/4-20 UNC X 1/2” LONG

F593 GR2 AND NYLON

29

SHCS, 3/8-16 UNC X 1-1/2” LONG

A286 GR 660

30

SHCS, 3/8-16 UNC X 1-1/4” LONG

A286 GR 660

31

SHCS, 5/16-18 UNC X 3/4” LONG

A286 GR 660

32

WEAR BAND, SEAL CARRIER

DELRIN AF

33

T-SEAL, ROD

CARBOXYLATED NITRILE / NYLATRON

34

SPRING, COMPRESSION

A313 TP 316

35

SPRING, COMPRESSION

AMS5699 (X-750)

36

BALL

A276 TP 316

37

O-RING (ITEM* 37-42)

HNBR

43

RING, BACKUP (ITEM* 43-46)

PEEK

Continued on page 7.2

3

1


Technical Sheet

Regulator Valve

VENT INLET

REGULATED

Pressure Regulator Manual Spring Single Inlet 3500/6000 PSI

Part Numbers

Description

29091

Valve, Pressure Regulator, Manual Spring, 3500-1500 psi range, SAE Ports, Single Inlet

29095

Valve, Pressure Regulator, Manual Spring, 1500-500 psi range, NPT Ports, Single Inlet

29130

Valve, Pressure Regulator, Manual Spring, 3500-1500 psi range, NPT Ports, Single Inlet

29132

Valve, Pressure Regulator, Manual Spring, 5500-2500 psi range, NPT Ports, Single Inlet

29133

Valve, Pressure Regulator, Manual Spring, 5500-2500 psi range, SAE Ports, Single Inlet

GAGE

Available Configurations: NPT, SAE, Code 62, Seal Sub Mounted

*The repair kit part number will match the category part number with (RK) at the end.

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-07.2

*The seal kit part number will match the category part number with (SK) at the end.


Technical Sheet

Regulator Valve

Pressure Regulator Manual Spring RH Single Inlet 3500/6000 PSI

FUNCTIONAL DESIGN SPECIFICATION

VENT INLET

REGULATED GAGE

Available Configurations: NPT, SAE, Code 62, Seal Sub Mounted

Maximum Inlet Pressure Pressure

6,000 PSI

Fully Open Flow Coefficient (Cv) Regulated

7

Fully Open Flow Coefficient (Cv) Vent

1

Set Point Range

3,500 - 1,500 PSI

Typical Deadband at 5000 PSI Supply

300 + 100 PSI

Typical Deadband at 3000 PSI Supply

200 + 50 PSI

Fully Open Max Regulated Flow Rate

125 GPM

Predicted Cycle Life

10,000 Cycles

Operating Temperature Range

32˚F to 150˚F

Storage Temperature Range

32˚F to 150˚F

Acceptable Operating Fluid Types

Water or mineral oil-based control fluid

Mounting Restrictions

None

US Patent

10,739,796

BILL OF MATERIALS

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-08

Item Number*

Description

1

BODY

2

FLANGE, BOTTOM, /8” SAE

A276 TP 316

3

GUIDE, PLUNGER, 1-1/2”

A276 TP 316

4

ADAPTER, SPRING HOUSING

A276 TP S21800 (NITRONIC 60)

5

HOUSING, SPRING

A276 TP 316

6

CAP, SPRING HOUSING

A276 UNS S21800 (NITRONIC 60)

7

NUT, O-LOCK

A276 TP 316

8

FLANGE INLET, RIGHT 1 /2” SAE

A276 TP 316

9

FLANGE BLANK, LEFT

A276 TP 316

10

CARRIER, SEAL

A276 TP S21800 (NITRONIC 60)

11

PLUNGER, 1-1/2”

A276 TP S21800 (NITRONIC 60)

Continued on page 8.1

Material A564 TP 630 (17-4 PH) 3


Technical Sheet

Regulator Valve

Pressure Regulator Manual Spring RH Single Inlet 3500/6000 PSI

BILL OF MATERIALS (CONT.)

VENT INLET

REGULATED GAGE

Available Configurations: NPT, SAE, Code 62, Seal Sub Mounted

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-08.1

Item Number*

Description

Material

12

CAP, LOCK

A276 TP 316

13

INSERT, FLOW PORT, SUPPLY AND VENT

TUNGSTEN CARBIDE / NICKEL

14

RING, SEAL, SUPPLY

TUNGSTEN CARBIDE / NICKEL

15

RING, SEAL, VENT

TUNGSTEN CARBIDE / NICKEL

16

WAVE SPRING

AMS5699 (X-750)

17

SPRING, COMPRESSION

AMS5699 (X-750)

18

SCREW, ADJUSTING

F593 GR2 (T316)

19

PLATE, SPRING

A276 TP 316

20

SPRING, COMPRESSION

A313 TP 316

21

SPRING, COMPRESSION

INCONEL X750

22

PLUG, HEX

A240 TP 316

23

PELLET, NYLOK

NYLON

24

HOLLOW HEX PLUG, 1/2 SAE

A240 TP 316

25

RING, BACKUP

PEEK

26

WIPER, D-STYLE, 1.500 PLUNGER

POLYURETHANE

27

WEAR BAND, PLUNGER

DELRIN AF

28

T-SEAL, ROD

CARBOXYLATED NITRILE / NYLATRON

29

WEAR BAND, 1-1/2”

DELRIN AF

30

SHCS, THREAD-LOCKING,

A593 T316

31

SHCS, 3/8-16 UNC X 1-1/2” LONG

A286 GR 660

32

SHCS, 3/8-16 UNC X 1-1/4” LONG

A286 GR 660

33

SHCS, 5/16-18 UNC X 3/4” LONG

A286 GR 660

34

WEAR BAND, SEAL CARRIER

DELRIN AF

35

SHCS, 3/8-16 UNC X 1-5/8” LONG

A286

36

WASHER, NORD-LOCK, 3 /8”

254 SMO

37

SEAL SUB, 1”

A564 TP 630 (17-4PH)

38

SEAL SUB, 1- /4”

Continued on page 8.2

1

A564 TP 630 (17-4PH)


Technical Sheet

Regulator Valve

Pressure Regulator Manual Spring RH Single Inlet 3500/6000 PSI

BILL OF MATERIALS (CONT.)

VENT INLET

Item Number*

Description

Material

39

BALL

A276 TP 316

40

INSERT, FLOW PORT, BLANK

TUNGSTEN CARBIDE / NICKEL

41

O-RING (ITEM* 41-47)

HNBR

42

RING, BACKUP (ITEM* 42-52)

PEEK

Part Numbers

Description

29131

Valve, Pressure Regulator, Manual Spring, 3500-1500 psi range, Seal Sub Mounted, RH Single Inlet

REGULATED GAGE

Available Configurations: NPT, SAE, Code 62, Seal Sub Mounted

*The repair kit part number will match the category part number with (RK) at the end.

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-08.2

*The seal kit part number will match the category part number with (SK) at the end.


Technical Sheet

Regulator Valve

Pressure Regulator Hydraulic Pilot Dual Inlets 5000/6000 PSI

FUNCTIONAL DESIGN SPECIFICATION

PILOT 2X VENT 2X INLET

REGULATED GAGE

Available Configurations: NPT, SAE, Code 62, Seal Sub Mounted

Maximum Inlet Pressure Pressure

6,000 PSI

Fully Open Flow Coefficient (Cv) Regulated

14

Fully Open Flow Coefficient (Cv) Vent

2

Set Point Range

5,000 - 300 PSI

Typical Deadband at 5000 PSI Supply

200 + 25 PSI

Typical Deadband at 1500 PSI Supply

100 + 25 PSI

Fully Open Max Regulated Flow Rate

300 GPM

Predicted Cycle Life

10,000 Cycles

Operating Temperature Range

32˚F to 150˚F

Storage Temperature Range

32˚F to 150˚F

Acceptable Operating Fluid Types

Water or mineral oil-based control fluid

Mounting Restrictions

None

US Patent

10,739,796

BILL OF MATERIALS

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-09

Item Number*

Description

Material

1

BODY

A564 TP 630 (17-4 PH)

2

FLANGE BOTTOM

3

GUIDE, PLUNGER, 1- /4”

A276 TP 316

4

INSERT, FLOW PORT, SUPPLY AND VENT

TUNGSTEN CARBIDE 8-10% NICKEL

5

CARRIER, SEAL

A276 TP S21800 (NITRONIC 60)

6

RING, SEAL, SUPPLY

TUNGSTEN CARBIDE 8-10% NICKEL

7

RING, SEAL, VENT

TUNGSTEN CARBIDE 8-10% NICKEL

8

WAVE SPRING

AMS5699 (X-750)

9

SPRING, COMPRESSION

AMS5699 (X-750)

10

PLUG, HEX, /8” SAE

A240 TP 316

11

PELLET, NYLOK

NYLON

12

HOLLOW HEX PLUG, 1/2”

A240 TP 316

Continued on page 9.1

A276 TP 316 3

3


Technical Sheet

Regulator Valve

Pressure Regulator Hydraulic Pilot Dual Inlets 5000/6000 PSI

BILL OF MATERIALS (CONT.)

PILOT 2X VENT 2X INLET

REGULATED

Item Number*

Description

13

SCHS, /8-16 UNC X 1- /2 LG

A286 GR 660

14

SCHS, 1/4-20 UNC X 1/2 LG

A593 T316 and (NYLON)

15

WEAR BAND, SEAL CARRIER

DELRIN AF

16

FLANGE, INLET, RIGHT

A276 TP 316

17

FLANGE, INLET, LEFT

A276 TP 316

18

SCHS, /8-16 UNC X 1- /8 LG

A286

19

WASHER, NORD-LOCK, 3 /8

254 SMO

20

SEAL SUB, 1”

A564 TP 630 (17-4PH)

21

SEAL SUB, 1- /4”

A564 TP 630 (17-4PH)

22

HYDRAULIC PLUNGER, 1-3/4”

A276 TP S21800 (NITRONIC 60)

23

WEAR BAND, PLUNGER

DELRIN AF

24

T-SEAL ,PISTON

CARBOXYLATED NITRILE / NYLATRON

25

RING, BACKUP (ITEM* 25-28)

PEEK

29

O-RING (ITEM* 29-34)

HNBR

27

BACKUP RING (ITEM* 35-36)

TEFLON

Part Numbers

Description

29092

Valve, Pressure Regulator, Hydraulic Pilot, Seal Sub Mounted, Dual Inlets

GAGE

Available Configurations: NPT, SAE, Code 62, Seal Sub Mounted

Material

3

1

3

5

1

*The repair kit part number will match the category part number with (RK) at the end.

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-09.1

*The seal kit part number will match the category part number with (SK) at the end.


Technical Sheet

Regulator Valve

Pressure Regulator Hydraulic Pilot Sin gle Inlet 5000/6000 PSI

FUNCTIONAL DESIGN SPECIFICATION

PILOT VENT INLET

REGULATED

GAGE

Available Configurations: NPT, SAE, Code 62, Seal Sub Mounted

Maximum Inlet Pressure Pressure

6,000 PSI

Fully Open Flow Coefficient (Cv) Regulated

7

Fully Open Flow Coefficient (Cv) Vent

1

Set Point Range

5,000 - 300 PSI

Typical Deadband at 5000 PSI Supply

200 + 25 PSI

Typical Deadband at 1500 PSI Supply

100 + 25 PSI

Fully Open Max Regulated Flow Rate

150 GPM

Predicted Cycle Life

10,000 Cycles

Operating Temperature Range

32˚F to 150˚F

Storage Temperature Range

32˚F to 150˚F

Acceptable Operating Fluid Types

Water or mineral oil-based control fluid

Mounting Restrictions

None

US Patent

10,739,796

BILL OF MATERIALS

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-010

Item Number*

Description

Material

1

BODY

A564 TP 630 (17-4 PH)

2

FLANGE BOTTOM

3

GUIDE, PLUNGER, 1- /4”

A276 TP 316

4

INSERT, FLOW PORT, SUPPLY AND VENT

TUNGSTEN CARBIDE 8-10% NICKEL

5

CARRIER, SEAL

A276 TP S21800 (NITRONIC 60)

6

RING, SEAL, SUPPLY

TUNGSTEN CARBIDE 8-10% NICKEL

7

RING, SEAL, VENT

TUNGSTEN CARBIDE 8-10% NICKEL

8

WAVE SPRING

AMS5699 (X-750)

9

SPRING, COMPRESSION

AMS5699 (X-750)

10

PLUG, HEX, /8” SAE

A240 TP 316

11

PELLET, NYLOK

NYLON

12

HOLLOW HEX PLUG, 1/2”

A240 TP 316

A276 TP 316 3

3

Continued on page 10.1


Technical Sheet

Regulator Valve

Pressure Regulator Hydraulic Pilot Sin gle Inlet 5000/6000 PSI

BILL OF MATERIALS (CONT.)

PILOT VENT INLET

REGULATED

GAGE

Available Configurations: NPT, SAE, Code 62, Seal Sub Mounted

Item Number*

Description

13

SCHS, /8-16 UNC X 1- /2 LG

A286 GR 660

14

SCHS, 1/4-20 UNC X 1/2 LG

A593 T316 and (NYLON)

15

INSERT, FLOW, BLANK

TUNGSTEN CARBIDE 8-10% NICKEL

16

WEAR BAND SEAL CARRIER

DELRIN AF

17

FLANGE 1” SAE INLET, 1 /2” SAE VENT

A276 TP 316

18

FLANGE, BLANK

A276 TP 316

19

HYDRAULIC PLUNGER, 1-3/4”

A276 TP S21800 (NITRONIC 60)

20

WEAR BAND, PLUNGER

DELRIN AF

21

T-SEAL, PISTON

CARBOXYLATED NITRILE / NYLATRON

22

FLANGE OUTLET

A276 TP 316

23

SCHS, /8-16 UNC-2A X 1-1/4 LG

18-8 SS, F593 ALLOY

24

RING, BACKUP (ITEM* 25-27)

PEEK

28

O-RING (ITEM* 28-32)

HNBR

Part Numbers

Description

29119

Valve, Pressure Regulator, Hydraulic Pilot, 1” SAE Single Inlet

29120

Valve, Pressure Regulator, Hydraulic Pilot, 1” NPT Single Inlet

3

Material 1

3

*The repair kit part number will match the category part number with (RK) at the end.

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-010.1

*The seal kit part number will match the category part number with (SK) at the end.


Technical Sheet

Regulator Valve

Pressure Regulator Hydraulic Pilot LH Inlet 5000/6000 PSI

FUNCTIONAL DESIGN SPECIFICATION

PILOT VENT INLET

REGULATED

GAGE

Available Configurations: NPT, SAE, Code 62, Seal Sub Mounted

Maximum Inlet Pressure Pressure

6,000 PSI

Fully Open Flow Coefficient (Cv) Regulated

7

Fully Open Flow Coefficient (Cv) Vent

1

Set Point Range

5,000 - 300 PSI

Typical Deadband at 5000 PSI Supply

200 + 25 PSI

Typical Deadband at 1500 PSI Supply

100 + 25 PSI

Fully Open Max Regulated Flow Rate

150 GPM

Predicted Cycle Life

10,000 Cycles

Operating Temperature Range

32˚F to 150˚F

Storage Temperature Range

32˚F to 150˚F

Acceptable Operating Fluid Types

Water or mineral oil-based control fluid

Mounting Restrictions

None

US Patent

10,739,796

BILL OF MATERIALS

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-011

Item Number*

Description

Material

1

BODY

A564 TP 630 (17-4 PH)

2

FLANGE BOTTOM

3

GUIDE, PLUNGER, 1- /4”

A276 TP 316

4

INSERT, FLOW PORT, SUPPLY AND VENT

TUNGSTEN CARBIDE 8-10% NICKEL

5

CARRIER, SEAL

A276 TP S21800 (NITRONIC 60)

6

RING, SEAL, SUPPLY

TUNGSTEN CARBIDE 8-10% NICKEL

7

RING, SEAL, VENT

TUNGSTEN CARBIDE 8-10% NICKEL

8

WAVE SPRING

AMS5699 (X-750)

9

SPRING, COMPRESSION

AMS5699 (X-750)

10

PLUG, HEX, 3/8” SAE

A240 TP 316

11

PELLET, NYLOK

NYLON

12

HOLLOW HEX PLUG, 1/2”

A240 TP 316

A276 TP 316 3

Continued on page 11.1


Technical Sheet

Regulator Valve

Pressure Regulator Hydraulic Pilot LH Inlet 5000/6000 PSI

BILL OF MATERIALS (CONT.)

PILOT VENT INLET

REGULATED

GAGE

Available Configurations: NPT, SAE, Code 62, Seal Sub Mounted

Item Number*

Description

Material

13

SCHS, /8-16 UNC X 1- /2 LG

A286 GR 660

14

SCHS, 1/4-20 UNC X 1/2 LG

A593 T316 and (NYLON)

15

WEAR BAND, SEAL CARRIER

DELRIN AF

16

FLANGE, BLANK RIGHT

A276 TP 316

17

FLANGE, INLET, LEFT

A276 TP 316

18

SCHS, /8-16 UNC X 1- /8 LG

A286

19

WASHER, NORD-LOCK, 3 /8

254 SMO

20

SEAL SUB, 1”

A564 TP 630 (17-4PH)

21

SEAL SUB, 1- /4”

A564 TP 630 (17-4PH)

22

HYDRAULIC PLUNGER, 1-3/4”

A276 TP S21800 (NITRONIC 60)

23

WEAR BAND, PLUNGER

DELRIN AF

24

T-SEAL ,PISTON

CARBOXYLATED NITRILE / NYLATRON

25

INSERT, FLOW PORT, BLANK

TUNGSTEN CARBIDE 8-10% NICKEL

26

RING, BACKUP (ITEM* 26-29)

PEEK

30

O-RING (ITEM* 30-35)

HNBR

36

BACKUP RING (ITEM* 36-37)

TEFLON

Part Numbers

Description

29121

Valve, Pressure Regulator, Hydraulic Pilot, Seal Sub Mounted, LH Inlet

3

1

3

5

1

*The repair kit part number will match the category part number with (RK) at the end.

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-011.1

*The seal kit part number will match the category part number with (SK) at the end.


Technical Sheet

Regulator Valve

Pressure Regulator Air Motor Single Inlet 1500/6000 PSI

FUNCTIONAL DESIGN SPECIFICATION

AIR 1/2” NPT 100 PSI MAX INCREASE VENT INLET

DECREASE

REGULATED

GAGE

Available Configurations: NPT, SAE, Code 62

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-012

Maximum Inlet Pressure Pressure

6,000 PSI

Fully Open Flow Coefficient (Cv) Regulated

7

Fully Open Flow Coefficient (Cv) Vent

1

Set Point Range

1,500 - 500 PSI

Typical Deadband at 5000 PSI Supply

400 + 100 PSI

Typical Deadband at 3000 PSI Supply

200 + 50 PSI

Fully Open Max Regulated Flow Rate

100 GPM

Predicted Cycle Life

10,000 Cycles

Operating Temperature Range

32˚F to 150˚F

Storage Temperature Range

32˚F to 150˚F

Acceptable Operating Fluid Types

Water or mineral oil-based control fluid

Mounting Restrictions

None

US Patent

10,739,796

BILL OF MATERIALS Item Number*

Description

Material

1

BODY

A564 TP 630 (17-4)

2

FLANGE, 1” NPT INLET, 1 /2” NPT VENT

A276 TP 316

3

FLANGE OUTLET

A276 TP 316

4

FLANGE BOTTOM

5

GUIDE, PLUNGER, 1- /2”

A276 TP 316

6

ADAPTER, SPRING HOUSING

A276 TP S21800 (NITRONIC 60)

7

HOUSING, SPRING

A276 TP 316

8

INSERT, FLOW PORT, BLANK

TUNGSTEN CARBIDE 8-10% NICKEL

9

INSERT, FLOW PORT, SUPPLY AND VENT

TUNGSTEN CARBIDE 8-10% NICKEL

10

CARRIER, SEAL

A276 TP S21800 (NITRONIC 60)

11

PLUNGER, 1-1/2”

A276 TP S21800 (NITRONIC 60)

A276 TP 316 1

Continued on page 12.1


Technical Sheet

Regulator Valve

Pressure Regulator Air Motor Single Inlet 1500/6000 PSI

BILL OF MATERIALS (CONT.)

AIR 1/2” NPT 100 PSI MAX INCREASE VENT INLET

DECREASE

REGULATED

GAGE

Available Configurations: NPT, SAE, Code 62

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-012.1

Item Number*

Description

Material

12

RING, SEAL, SUPPLY

TUNGSTEN CARBIDE 8-10% NICKEL

13

RING, SEAL, VENT

TUNGSTEN CARBIDE 8-10% NICKEL

14

WAVE SPRING

AMS5699 (X-750)

15

SPRING, COMPRESSION

AMS5699 (X-750)

16

PLATE, SPRING

A276 TP 316

17

PLUG, HEX, /8” SAE

A240 TP 316

18

PELLET, NYLOK

19

HOLLOW HEX PLUG, /2”

A240 TP 316

20

WIPER, D-STYLE, 1.500 PLUNGER

POLYURETHANE

21

FLANGE, BLANK

A276 TP 316

22

WEAR BAND, PLUNGER

DELRIN AF

23

SCHS, THREADLOCKING

A593 T316

24

SCHS, 3/8-16 UNC X 1-1/2 LG

A286 GR 660

25

SCHS, 3/8-16 UNC X 1-1/4 LG

A286 GR 660

26

SCHS, 5/16-18 UNC X 3 /4 LG

A286 GR 660

27

WEAR BAND, SEAL CARRIER

DELRIN AF

28

T-SEAL, ROD

CARBOXYLATED NITRILE / NYLATRON

29

SPRING, COMPRESSION

AMS5670 (X-750)

30

AIR MOTOR

REFERENCED

31

BACKUP RING (ITEM* 31-35)

PEEK

36

O-RING (ITEM* 36-40)

HNBR

Part Numbers

Description

29096

Valve, Pressure Regulator, Air Motor,1500-500, NPT , Single Inlet

29137

Valve,Pressure Regulator, Air Motor,3500-1500,NPT ,Single Inlet

3

NYLON 1

Continued on page 12.2


Technical Sheet

Regulator Valve

Pressure Regulator Air Motor Single Inlet 1500/6000 PSI

Part Numbers

Description

29138

Valve, Pressure Regulator, Air Motor,1500-500, NPT , Single Inlet

29139

Valve,Pressure Regulator, Air Motor,5500-2500,SAE ,Single Inlet

AIR 1/2” NPT 100 PSI MAX INCREASE VENT INLET

DECREASE

REGULATED

GAGE

Available Configurations: NPT, SAE, Code 62

*The repair kit part number will match the category part number with (RK) at the end.

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-012.2

*The seal kit part number will match the category part number with (SK) at the end.


Technical Sheet

Regulator Valve

Pressure Regulator Air Motor Dual Inlets 3500/6000 PSI

FUNCTIONAL DESIGN SPECIFICATION

AIR 1/2” NPT 100 PSI MAX INCREASE 2X VENT 2X INLET

DECREASE

REGULATED

GAGE

Available Configurations: NPT, SAE, Code 62

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-013

Maximum Inlet Pressure Pressure

6,000 PSI

Fully Open Flow Coefficient (Cv) Regulated

14

Fully Open Flow Coefficient (Cv) Vent

2

Set Point Range

3500 - 1500 PSI

Typical Deadband at 5000 PSI Supply

300 + 100 PSI

Typical Deadband at 3000 PSI Supply

200 + 50 PSI

Fully Open Max Regulated Flow Rate

250 GPM

Predicted Cycle Life

10,000 Cycles

Operating Temperature Range

32˚F to 150˚F

Storage Temperature Range

32˚F to 150˚F

Acceptable Operating Fluid Types

Water or mineral oil-based control fluid

Mounting Restrictions

None

US Patent

10,739,796

BILL OF MATERIALS Item Number*

Description

Material

1

BODY

A564 TP 630 (17-4)

2

FLANGE, 1” SAE INLET, 1 /2” SAE VENT

A276 TP 316

3

FLANGE OUTLET

A276 TP 316

4

FLANGE BOTTOM

5

GUIDE, PLUNGER, 1- /2”

A276 TP 316

6

ADAPTER, SPRING HOUSING

A276 TP S21800 (NITRONIC 60)

7

HOUSING, SPRING

A276 TP 316

8

INSERT, FLOW PORT, SUPPLY AND VENT

TUNGSTEN CARBIDE 8-10% NICKEL

9

CARRIER, SEAL

A276 TP S21800 (NITRONIC 60)

10

PLUNGER, 1-1/2”

A276 TP S21800 (NITRONIC 60)

A276 TP 316 1

Continued on page 13.1


Technical Sheet

Regulator Valve

Pressure Regulator Air Motor Dual Inlets 3500/6000 PSI

BILL OF MATERIALS (CONT.)

AIR 1/2” NPT 100 PSI MAX INCREASE 2X VENT 2X INLET

DECREASE

REGULATED

GAGE

Available Configurations: NPT, SAE, Code 62

Item Number*

Description

Material

11

RING, SEAL, SUPPLY

TUNGSTEN CARBIDE 8-10% NICKEL

12

RING, SEAL, VENT

TUNGSTEN CARBIDE 8-10% NICKEL

13

WAVE SPRING

AMS5699 (X-750)

14

SPRING, COMPRESSION

AMS5699 (X-750)

15

PLATE, SPRING

A276 TP 316

16

PLUG, HEX, /8” SAE

A240 TP 316

17

PELLET, NYLOK

18

HOLLOW HEX PLUG, /2”

A240 TP 316

19

WIPER, D-STYLE, 1.500 PLUNGER

POLYURETHANE

20

WEAR BAND, PLUNGER

DELRIN AF

21

SCHS, THREADLOCKING

A593 T316

22

SCHS, 3/8-16 UNC X 1-1/2 LG

A286 GR 660

23

SCHS, 3/8-16 UNC X 1-1/4 LG

A286 GR 660

24

SCHS, 5/16-18 UNC X 3 /4 LG

A286 GR 660

25

WEAR BAND, SEAL CARRIER

DELRIN AF

26

T-SEAL, ROD

CARBOXYLATED NITRILE / NYLATRON

27

SPRING, COMPRESSION

AMS5670 (X-750)

28

AIR MOTOR

REFERENCED

29

BACKUP RING (ITEM* 29-33)

PEEK

34

O-RING (ITEM* 34-38)

HNBR

Part Numbers

Description

29144

Valve, Pressure Regulator, Air Motor,1500-3500, SAE , Dual Inlets

3

NYLON 1

*The repair kit part number will match the category part number with (RK) at the end.

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-013.1

*The seal kit part number will match the category part number with (SK) at the end.


Technical Sheet

Regulator Valve

Pressure Regulator Compensator Dual Inlets 4500/6000 PSI

FUNCTIONAL DESIGN SPECIFICATION

2X VENT 2X INLET

REGULATED GAGE

Available Configurations: SAE, Other connections avalable upon request

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-014

Maximum Inlet Pressure Pressure

6,000 PSI

Fully Open Flow Coefficient (Cv) Regulated

14

Fully Open Flow Coefficient (Cv) Vent

2

Set Point Range

4,500 - 2,000 PSI

Typical Deadband at 5000 PSI Supply

400 + 100 PSI

Fully Open Max Regulated Flow Rate

250 GPM

Predicted Cycle Life

10,000 Cycles

Operating Temperature Range

32˚F to 150˚F

Storage Temperature Range

32˚F to 150˚F

Acceptable Operating Fluid Types

Water or mineral oil-based control fluid

Mounting Restrictions

None

US Patent

10,739,796

BILL OF MATERIALS Item Number*

Description

Material

1

BODY

A564 TP 630 (17-4 PH)

2

FLANGE BOTTOM

A276 TP 316

3

GUIDE, PLUNGER, 1-1/4”

A276 TP 316

4

ADAPTER, SPRING HOUSING

A276 TP S21800 (NITRONIC 60)

5

SPRING HOUSING, COMPENSATOR

A276 TP 316

6

CAP, SPRING HOUSING, COMPENSATOR

A276 UNS S21800 (NITRONIC 60)

7

NUT, O-LOCK

A276 TP 316

8

CAP, LOCK

A276 TP 316

9

INSERT, FLOW PORT, SUPPLY AND VENT

TUNGSTEN CARBIDE 8-10% NICKEL

10

CARRIER, SEAL

A276 TP S21800 (NITRONIC 60)

11

PLUNGER, 1-1/4”

A276 TP S21800 (NITRONIC 60)

12

RING, SEAL, SUPPLY

TUNGSTEN CARBIDE 8-10% NICKEL

Continued on page 14.1


Technical Sheet

Regulator Valve

Pressure Regulator Compensator Dual Inlets 4500/6000 PSI

BILL OF MATERIALS (CONT.)

2X VENT 2X INLET

REGULATED GAGE

Available Configurations: SAE, Other connections avalable upon request

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-014.1

Item Number*

Description

Material

13

RING, SEAL, VENT

TUNGSTEN CARBIDE 8-10% NICKEL

14

WAVE SPRING

AMS5699 (X-750)

15

SPRING, COMPRESSION

AMS5699 (X-750)

16

SCREW, ADJUSTING

F593 GR2 (T316)

17

PLATE, SPRING

A276 TP 316

18

PLUG, HEX, 3/8” SAE

A240 TP 316

19

PELLET, NYLOK

NYLON

20

HOLLOW HEX PLUG, 1/2”

A240 TP 316

21

WIPER, D-STYLE, 1-1/4” OD PLUNGER

POLYURETHANE

22

WEAR BAND, PLUNGER, 1-1/4”

DELRIN AF

23

SCHS, THREADLOCKING, 1/4-20 UNC X 1 /2” LONG

F593 GR2 AND NYLON

24

SCHS, 3/8-16 UNC X 1-1/2 LG

A286 GR 660

25

SCHS, 3/8-16 UNC X 1-1/4 LG

A286 GR 660

26

SCHS, 5/16-18 UNC X 3 /4 LG

A286 GR 660

27

WEAR BAND, SEAL CARRIER

DELRIN AF

28

T-SEAL ROD

BUNA-N / NYLATRON

29

WEAR BAND

DELRIN AF

30

SPRING, COMPRESSION

A313 TP 316

31

FLANGE, 1-1/2” C62

A276 TP 316

32

FLANGE, INLET, 1” C62

A276 TP 316

33

SPRING, COMPRESSION

INCONEL X750

34

BALL

A276 TP 316

35

PORT PLUG, 1/4” NPT

F593 T316

36

COMPENSATOR

REFERENCED

37

BACKUP RING (ITEM* 37-40)

PEEK

41

O-RING (ITEM* 41-47)

HNBR

Continued on page 14.2


Technical Sheet

Regulator Valve

Pressure Regulator Compensator Dual Inlets 4500/6000 PSI

Part Numbers

Description

29094

Valve, Pressure Regulator, Compensator, 1-1/2” C62, Dual Inlets

2X VENT 2X INLET

REGULATED GAGE

Available Configurations: SAE, Other connections avalable upon request

*The repair kit part number will match the category part number with (RK) at the end.

INFO@gilmore.com www.gilmore.com REGULATOR -080521-001-014.2

*The seal kit part number will match the category part number with (SK) at the end.


Gilmore 1231 Lumpkin Road Houston, TX 77043 +1 713 468 8778

INFO@gilmore.com www.gilmore.com