Page 1

RX45 & RX55 Scissor Lifts Maximum productivity, minimum space

UPDATED

w


RX45 & RX55 Scissor Lifts

Large capacity with a small footprint

EXCLUSIVE

Best-in-class drive-on height 280 mm OTHERS

254 mm RX55

222 mm RX45

STANDARD

Wide runways %%610 mm (24 in.) runways 610 mm

%%Minimize clearance issues

accept wide vehicles

OPTIONAL

Stainless steel turnplates

%%Maximum corrosion resistance for long life %%Optional PowerSlideÂŽ turnplates (shown) lock/unlock automatically

STANDARD

PATENTED

STANDARD

Integrated air line

Sensor feedback system*

Velocity safety fuses

%%Convenient air source for tools

%%Sensors keep runway level %%Safely stops if obstructed

%%Instantaneous shutdown in

at front and rear

* Shown with protective cover removed

event of hydraulic failure


OPTIONAL

EXCLUSIVE

PATENTED

Two Swing Air Jacks

Louvered ramps

Control panel

%%2720-kg (6000-lb.) capacity %%Technicians’ favorite

%%Prevent wheel spin in wet

%%Complete operation from

conditions %%More effective than diamond tread or abrasive strips

the console %%Optional PowerSlide®, Inflation Station and FIA control

RX45KLIS-435E shown with optional light kit, Swing Air Jacks, and front turnplates STANDARD

EXCLUSIVE

PATENTED

Safety locks

Movable work steps

Inflation Station

%%Precision-fit teeth lock runways

%%10 secure positions %%Lightweight design

%%Automatically fills or bleeds

at 16 level height positions

OPTIONAL

each tire %%No dangling air lines


Exclusive features, enhanced capabilities EXCLUSIVE

Fast descent speed %%50% faster lowering times %%Ensures a soft landing by automatically slowing the last several inches

FAST Descent

0:25

0:50 Others

OPTIONAL

Swing Air Jacks %%Lift vehicles off the runways during alignment procedures and other multi-service operations %%2720-kg (6,000-lb.) capacity %%Folding design provides lowest-profile

133-85-1 — 2720-kg (6000-lb.) Capacity Swing Air Jack

EXCLUSIVE

OPTIONAL

Flush-mount installation %%Accommodate lowered vehicles or expensive spoilers %%Ideal for “showcase” shops %%Drive-thru capability Add F to any RX45K or RX55K model number


EXCLUSIVE

OPTIONAL

AlignLights system %%Bright and efficient LED light source underneath the vehicle %%Automatically turns on when the lift is raised and turns off when the lift is lowered to the floor %%AlignLights is an ALI-listed accessory 20-3438-1 — AlignLights system

Standard equipment %%Flush-mounted, full-floating slipplates (PowerSlide® slipplates on PS and IS models) %%Two movable work steps (not included with flush-mount installations) %%Louvered ramps with built-in wheel stops %%Front wheel stops %%Two wheel chocks %%Built-in, full-length jack rails %%Built-in air line kit

OPTIONAL

Extension kits Approach ramp extensions

Drive-thru conversion kits*

305 mm (12 in.) kit – 20-3112-1 Standard with RX55K 432 mm (17 in.) kit – 20-3113-1 Adds approximately 127 mm (5 in.) to RX55K when substituted for 20-3112-1 1016 mm (40 in.) kit* – 20-2169-1 Adds approximately 711 mm (28 in.) to RX55K 1270 mm (50 in.) kit* – 20-2189-1 Adds approximately 965 mm (38 in.) to RX63K

52 in. kit – 20-2498-1 For camera sensors 63 in. kit – 20-2501-1 For conventional sensors

* Quick-release pins included.


Hunter offers two fully integrated options to enhance productivity

FIA allows WinAlignÂŽ aligners to control the lift features for ultimate productivity. Two patented designs offer greater flexibility and time-saving capabilities.

Shown with optional aligner console, sensors, Swing Air Jacks, front turnplates, target support brackets, and lights


PATENTED

PowerSlide® edition %%Locks slipplates and turnplates with the

touch of a button or automatically through OPTIONAL an FIA-equipped aligner* %%No more struggles with lock pins %%Avoid wear and tear and extend the life of your turnplates

OPTIONAL Yesterday's Technology

Minimize trips around the car 1 Mount targets 2 Make adjustments 3 Remove targets Only 3 Trips! 1

2

4 Jack vehicle and compensate sensors 8 Trips

5 Lower leveling legs (if equipped) 6 Remove slipplate and turnplate pins

3

7 Replace slipplate and turnplate pins

8

7

6

5

4

3

2

1

8 Raise leveling legs (if equipped)

PATENTED

Inflation Station edition %%Includes PowerSlide® slipplates and turnplates %%Automatically inflate all four tires simultaneously %%Record starting and final pressure* %%Hose recoils to keep work area clear

Printouts show starting and final tire pressures.*

* Requires FIA equipped aligner with WinAlign® 10.x software or greater


Specifications RX55K 5500 kg (12125 lbs.)

RX45KL 4536 kg (10000 lbs.)

Max. vehicle weight Max. wheelbase surface/flush General 4673/4572 mm 4673/4572 mm 4343/4241 mm service (184/180 in.) (184/180 in.) (171/167 in.) Two-wheel 4547/4445 mm 4547/4445 mm 4216/4115 mm alignment (179/175 in.) (179/175 in.) (166/162 in.) Four-wheel 4013 mm 4013 mm 4013 mm alignment (158 in.) (158 in.) (158 in.) Min. four-wheel 2235 mm 2235 mm 2235 mm alignment (88 in.) (88 in.) (88 in.) 254 mm 222 mm 222 mm Lowered height (10 in.) (8.75 in.) (8.75 in.) Max. lifting 1803 mm 1829 mm 1829 mm height (71 in.) (72 in.) (72 in.) Alignment height All lock positions Runway width 610 mm (24 in.) Tread width Min. inside 1016 mm (40 in.) Max. outside 2235 mm (88 in.) Air pressure 6.2-10.3 bar (90-150 psi)* Speed 55 seconds (raise), 25 seconds (descent) * 8.6 bar (125 psi) required for full jack capacity

Models Fully Integrated Alignment Inflation Station PowerSlide® slipplates Flush-mount Long-deck (RX45K models only)

RX55KIS RX55KPS RX55K RX45KIS RX45KPS RX45K % % % % % Add F to any RX model number (ex. RX45KF) Add L to any RX45 model number (ex. RX45KLIS)

Because of continuing technological advances, specifications, models and options are subject to change without notice. PowerSlide and WinAlign are registered trademarks of Hunter Engineering Company. The PowerSlide logo is a trademark of Hunter Engineering Company. 0418AH Copyright © 2018, Hunter Engineering Company

RX45K Plan View

RX45K 4536 kg (10000 lbs.)

13 FT. (3962 mm) RECOMMENDED 13 BAY FT. (3962 mm) WIDTH RECOMMENDED BAY WIDTH

OPTIONAL EXTENDED OPTIONAL WHEEL STOP EXTENDED WHEEL STOP 11 5/8 IN. (295 mm) 11 5/8 IN. (295 mm)

ALIGNMENT EQUIPMENT ALIGNMENT EQUIPMENT LEAVE AMPLE WORKSPACE BETWEEN EQUIPMENT AND LIFT RACK LEAVE AMPLE WORKSPACE BETWEEN EQUIPMENT AND LIFT RACK 16 IN. (406 mm) 16 IN. (406 mm)

7 FT. - 4 1/2 IN. (2248 mm) 7 FT. - 4 1/2 IN. (2248 mm) FOR RX45K, RX45KPS AND FOR RX45K, RX45KIS RX45KPS AND 20 FT. - 1 1/4 IN. RX45KIS (6128 mm) 20 FT. - 1 1/4 IN. (6128 mm) FOR RX45KL, RX45KLPS FORRX45KLIS RX45KL, AND 21RX45KLPS FT. - 2 1/4 IN. AND RX45KLIS (6458 mm) 21 FT. - 2 1/4 IN. (6458 mm)

PRIOR TO LIFT INSTALLATION: PRIOR TO230VAC, LIFT INSTALLATION: INSTALL 1 PHASE, 60 HZ FOR 26 AMP DRAW NEAR INSTALL 230VAC, 1 PHASE, CONTROL CONSOLE LOCATION. 60 HZ FOR 26 AMP DRAW NEAR CONTROL LOCATION. 125-150 PSICONSOLE (8.6-10.3 BAR) SHOP AIR MUST ALSO BE SUPPLIED. 125-150 PSI (8.6-10.3 BAR) SHOP AIR MUST ALSO BE SUPPLIED. 2 IN. (51 mm) SIDE POCKET 2 IN. (51 mm) SIDE POCKET 16 IN. (406 mm) 16 IN. (406 mm) 21 IN. (533 mm) 21 IN. (533 mm) CONSOLE HEIGHT 45 IN. (1143 mm) CONSOLE HEIGHT 45 IN. (1143 17mm) - 32 IN. (432 - 813 mm) 17 - 32 IN. (432 - 813 mm)

24 IN. (610 mm) 24 IN. (610 mm)

4 IN. (101 mm) RECOMMENDED MIN. 4 IN. (101 mm) RECOMMENDED MIN.

See your Hunter Sales Representative for details on site requirement.

Add one of the following suffixes to the desired model number listed to the left (ex. RX55K-435E): Suffix -215E -216E -435E

Power configuration 208/230V, 1PH, 50Hz 208/230V, 1PH, 60Hz 208/230/400/460V, 3PH, 50Hz

11250 Hunter Drive, Bridgeton, MO 63044, USA Tel: +1-314-731-3020, Fax: +1-314-731-0132 Email: international@hunter.com Form 7472-TE-05, 04/18

Hunter RX45 Scissor Lift  
Hunter RX45 Scissor Lift