Page 1

Quick Start Card

in.xm2-ce™ European version 1- Connect all outputs & keypads L1 - Light connector

CO - Communication link

Power box display and buttons Installation brackets

General I/O connector (IR receiver) C - Main and aux. keypad connectors

Fuses

OUT8 - Connector for direct 230 V AC output

Main power entry connection

OUT7 OUT6 OUT5

Main power cable input entry

Mounting feet

OUT4 OUT3

OUT2

OUT1

RH - Output connectors for in.therm™ remote heating system (230 vac)

2- Connect the main power

3- Select spa configuration (see chart next page)

For 230 VAC Correct wiring of the electrical service box, RCD, and pack terminal block is essential. Call an electrician if necessary.

First, the led display will show "LL" and "01" continuously. Press Change button to choose the appropriate configuration for your spa. Press Select button to confirm. (The pack will now reset and reboot)

LIN

E1

LIN

E1

LIN

Note: To re-enter the configuration selection menu, press Select button and hold for 5 seconds.

E2

NEU

NEU

TRA

GR

L

TRA

OU

GR

ND

1 x 230 VAC Single-phase

L

OU

ND

2 x 230 VAC Dual-phase

LIN

LIN

E1

E1

LIN

E2 LIN

E2

LIN

E3

NEU

LIN

TRA

GR

E3

L

GR

OU

ND

3 x 230 VAC Three-phase

OU

ND

3 x 230 VAC Three-phase (Delta)

For more information, see our website: www.geckoalliance.com

4- Select breaker current Make sure all accessories are linked to the bonding connector and connected to pack. Make sure the spa pack door is closed. Turn on the breaker.

4.b- Selecting breaker current (Br) Press Change button to choose the breaker current value. Press Select button to confirm. (The pack will now reset and reboot.) Br values displayed by the system correspond to the maximum amperage capacity of the RCD.

Bonding lug 4.a- Selecting number of phase (Ph) Ph 1 = 1 phase Ph 2 = 2 phases Ph 3 = 3 phases

Ph 1P 2P 3P

Br (RCD) 40 A max. 20 A max. 16 A max.

Press Change button to choose the phase. Press Select button to confirm. For more information, see our website: www.geckoalliance.com


Configuration selection chart Software #186, rev. 3.00 Config. #

Pump 1

Pump 2

Pump 3

Pump 4

Pump 5

BL

Circ. Pump

Heat with P1 or CP?

Filtration / Ozone with P1 or CP?

1

1sp

_

_

_

_

_

x

CP

CP

2

1sp

_

_

_

_

x

x

CP

CP

3

1sp

1sp

_

_

_

_

x

CP

CP

4

1sp

1sp

_

_

_

x

x

CP

CP

5

1sp

1sp

x

_

_

_

x

CP

CP

6

1sp

1sp

x

_

_

x

x

CP

CP

7

1sp

1sp

x

x

_

_

x

CP

CP

8

1sp

1sp

x

x

_

x

x

CP

CP

9

1sp

1sp

x

x

x

_

x

CP

CP

10

1sp

1sp

x

x

x

x

x

CP

CP

11

2sp

_

_

_

_

_

_

P1

P1

12

2sp

_

_

_

_

_

x

CP

CP

13

2sp

_

_

_

_

x

_

P1

P1

14

2sp

_

_

_

_

x

x

CP

CP

15

2sp

1sp

_

_

_

_

_

P1

P1

16

2sp

1sp

_

_

_

_

x

CP

CP

17

2sp

1sp

_

_

_

x

_

P1

P1

18

2sp

1sp

_

_

_

x

x

CP

CP

19

2sp

1sp

x

_

_

_

_

P1

P1

20

2sp

1sp

x

_

_

_

x

CP

CP

21

2sp

1sp

x

_

_

x

_

P1

P1

22

2sp

1sp

x

_

_

x

x

CP

CP

23

2sp

2sp

x

_

_

_

_

P1

P1

24

2sp

2sp

x

_

_

_

x

CP

CP

25

2sp

2sp

x

_

_

x

_

P1

P1

26

2sp

2sp

x

_

_

x

x

CP

CP

Glossary P1 CP 1sp 2sp X

Note: This low level configuration table is valid for the sofware #186 revision 3. This information is displayed on top side keypad at spa pack power-up. Software number is displayed first (ex: , , 8 ), followed by revision (ex: 3.00 ). For in.k600™ (menu-driven interface), you will find the information in Info sub-menu located in Options menu.

Pump 1 Circulation Pump 1 speed pump 2 speeds pump Installed

For complete TechBook or more information, see our website: www.geckoalliance.com

© Groupe Gecko Alliance Inc., 2016 All trademarks or registered trademarks are the property of their respective owners.

9919-101182-B

Rev. 07-2016

www.geckoalliance.com

in.xm2-ce control system Quick Start Card (European version)  

Quick Start Card of Gecko Alliance’s in.xm2-ce control system for spas (European version)