Page 1

Some Plumbing and Heating Advices You Should Consider


Synopsis 1. Simple Plumbing and Heating Advice to Keep Things Functional 2. Plumbing and Heating: Few Things to Remember to Prevent Pipe Bursting 3. Plumbing and Heating Advice to Save You Money on Repairs

4. Few Simple Tips to Prevent and Correct Plumbing and Heating Problems 5. Common Winter Furnace Cleaning and Maintenance Tips for All 6. The Right Way to Deal with the Furnace Cleaning 7. Simple Yet Effective Ways to Select the Best Furnace Repair Technician 8. Furnace Repair and Replacement: What are the Factors Affecting Replacement Costs?


Simple Plumbing and Heating Advice to Keep Things Functional ď‚´ Do not ignore any leaky faucet in your home. The issue may not look big at first, but things will quickly go out of hand if you do not take immediate actions. Also, you need to bear in mind that it takes no time to lose gallons of water when you have a single leaky faucet in your home. ď‚´ Think seriously of making hot-water storage tank more efficient by insulating it properly. It is also a good idea to insulate all those storage pipes as well. While doing it, ensure that you do not cover the thermostat or you may run into serious trouble in no time. In case of oil or gas hot-water storage tanks, you should not insulate the heater's top and bottom. Avoid covering its burner compartment and thermostat. When not sure, do not hesitate to talk to a plumbing and heating expert. ď‚´ Make special moves to lower your water bill, and one simple thing is to opt for non-aerating low-flow showerheads and faucets. These fixtures may cost you a bit more, but you will end up saving some good money on your water bill.


Simple Plumbing and Heating Advice to Keep Things Functional ď‚´ Do not wait for your 8-year-old water heater to go bad. While most water heaters continue to serve you up to 10 years, it is better to start looking for a new one once yours is at least 8 years old. At least, you should start paying more attention to its maintenance to ensure it does not break down at wrong times. Be sure to spend some time in educating yourself about different types of heaters currently available in the market because it will help you select a new one that perfectly meets your needs. ď‚´ Pay special attention to your thermostat settings when you have a new water heater installed. Most of the times, water heaters have higher temperature settings when you install them for the first time. Be sure to check it and lower it to make it serve you well. It is usually a good idea to keep it below 115F because it provides enough hot water at this setting. ď‚´ Consider draining some water from the water tank at regular intervals. Ideally, you should drain around a quart of water and do it every three months to ensure that there is no sediment in it to impede heat transfer.


Plumbing and Heating: Few Things to Remember to Prevent Pipe Bursting 

Be very careful when using toilet paper. Experts have found that using too much toilet paper with inadequate flushing can lead to serious problems. It may clog your toilet pipes and require serious attention. Similarly, you will experience the same problem when flushing foreign objects. Pay attention to how your young children use the toilet. Do not let them use it the wrong way or else get ready to call in a plumbing and heating specialist for help.

Do not ignore any clogs in the kitchen. Fats can damage your kitchen pipes, especially those pipes underneath your sink – their curved shape makes them vulnerable to damage. Fatty materials may accumulate in that area, causing stubborn clogs to develop. Ensure that you do not let clogs go unnoticed. It is a good idea to use strainers in the sinks. Moreover, you need to ensure that you never dispose of cooking oils and grease through the drain. It is important to take precautionary measures, but you may eventually have some greasy soapy reside in those pipes. To keep them in top working condition, make a habit of running hot water for five minutes down those pipes at regular intervals. Doing it periodically will keep your pipes working just fine and you will not have to worry about pipe bursting.


Plumbing and Heating: Few Things to Remember to Prevent Pipe Bursting  Fix clogs in the bathtub in a timely manner. It is common to have blocked sink pipes because of hair and soap. The same factors may lead to a blocked bathtub. It is a good idea to clean hair and soap regularly and do not let them accumulate. You should make use of a strainer to prevent clogs in the first place. Similarly, you should consider pouring boiling hot water down those pipes at least once a month to prevent serious issues. Remember, not removing hair and soap in a timely manner may lead to a blockage issue too big to be handled by you. If you have already clogged those sink pipes, call your plumbing and heating company for assistance.  Consider leaving a faucet running slowly when the temperature outside is very low. It may certainly be a waste of water, but keeping water running through the system may go a long way in preventing bursting pipes.  Consider directing warm air to pipes that are more likely to freeze. Most of these pipes are usually located outside a window or wall.


Plumbing and Heating Advice to Save You Money on Repairs  Be sure to take your time when shopping for a water heater. It is a good idea to buy a heater with a good first-hour rating (FHR). You can make a right choice by considering how much hot water your family requires at different times.  Consider taking advantage of a solar water heater if you live in a warm climate. It will be extremely beneficial especially if you have to use electricity to get hot water.  Consider taking showers instead of taking baths. You have to understand that you will be using 15-25 gallons of hot water when taking a bath, whereas you can save 5-15 gallon when taking a 5minute shower.  Whenever possible, opt for oil, gas, or propane water heaters. They last longer and do not cost you as much as electric models do. Before finalizing a decision, you may want to consider the right type of fuel for your water heater.  Pay attention to the length of piping you require to use hot water in your bathroom and kitchen. Find an appropriate location to minimize the total length of piping you need.


Plumbing and Heating Advice to Save You Money on Repairs 

Do not leave your drain clogged or the problem will spiral out of control. You can try simple home remedies to correct the problem. A simple solution is to pour half a cup of vinegar along with half a box of baking soda down your drain. Leave it for half an hour and then pour boiling water into the drain. In most cases, it should resolve the problem, but if the problem persists, be sure to talk to a plumbing and heating expert.

Be sure to take advantage of timers to use your electric water heaters more efficiently. A timer can turn your water heater off and on at the right times. It may cost some money, but in most cases, it pays for itself in a year or so.

Do not leave your sinks and toilets clogged. Timely actions can prevent expensive repairs. You can use plungers to good effect, but remember that sinks and toilets usually require different types of plungers. You will get good results only when you are using the correct one.

Regularly check all your pipes for possible leaks. You may not notice there is a leak until you check all the pipes carefully. A small leak can lead to the wastage of up to 20 gallons of water a day, and larger leaks can certainly wreak havoc. So, be sure to inspect all the pipes to fix the issue as soon as possible.


Few Simple Tips to Prevent and Correct Plumbing and Heating Problems  Never ignore any clogged drains. You should take corrective steps in a timely manner to avoid wasting a lot of money.  Never go heavy on bleach, detergent, and other chemicals. Even when you want to disinfect different surfaces, you should avoid using harsh chemicals. Interestingly, your septic system really needs the natural bacteria to function properly, so using harsh chemicals can actually cause serious problems.  Never overlook a leaky toilet because it can make you waste a large amount of water; in fact, it increases your water usage by 40% or more in some cases. If you have found the leak, ensure that you fix it as soon as possible. In case you suspect there is a leak in your toilet, sink, or water, ensure that you have turned off the water before trying to repair it yourself. If you are not sure how to proceed, there is no harm in hiring a plumbing and heating expert to fix it when it does not require a lot of work.


Few Simple Tips to Prevent and Correct Plumbing and Heating Problems  Consider replacing metal piping with plastic piping if you experience any problem. Plastic piping is usually of higher quality and is cheaper than metal as well. You will find it a lot easier to install and adjust plastic piping on your own. You can repair it easily if there is a leakage problem. A good thing about plastic piping is that it does not corrode like that metal piping you may already have installed in your home.  Be sure to check your faucets regularly for any leakage problems. When you have dripping faucets, there is usually a problem with washers. The issue may also be the result of bad internal seats or faulty faucet cartridges. Check all these parts to fix the issue.  Pay attention to the water pressure in the pipes. It should be less than 80 pounds per square inch. If it is higher, it will eventually damage your faucet and cause leakage problems.  Do not use harsh chemicals to open your clogged kitchen sink. Grease is usually the underlying problem here, but you do not want to correct it by using harsh chemicals, as they can corrode the pipes. A better option would be to pour ¼ cup of common dish soap down the drain and leave it for at least 20 minutes. Finish by pouring some boiling water in the drain to get good results.


Common Winter Furnace Cleaning and Maintenance Tips for All  Ensure that the filter of your furnace is in good condition. Understand that the filter of your furnace is one of its most important parts because it stops dust, debris, insects and other foreign particles from entering the furnace and causing problems. It also helps take the warm air out through the duct system. Not paying attention to furnace cleaning may lead to a clogged up filter, which directly affects the airflow and the efficiency of your furnace. Due to a reduced airflow, there will be a serious strain on the heat exchanger. The excessive strain can cause cracks – it can sometimes cause a meltdown, which requires a big-ticket replacement. Leaving it unattended would have a direct impact on your heating costs as well. Therefore, you should check your furnace's filter regularly and have it cleaned properly to ensure the furnace keeps working properly.  Perform a visual furnace inspection to ensure everything is in the right condition. Before approaching the furnace, ensure that you have flipped off the circuit breaker. You should turn down the thermostat and wait until the furnace gets cool. Check your furnace carefully and notice any sign of damage. Look for the presence of any black soot or residue. It is usually the result of combustion, and if it is present, you may want to ask a plumbing and heating expert to have a closer look at the furnace.


Common Winter Furnace Cleaning and Maintenance Tips for All ď‚´ Similarly, you should look for the presence of any dust and debris. Use a handheld vacuum cleaner to help remove the debris. After you have completed furnace cleaning, you should turn it on and pay attention to the color of the pilot light flame. Things are usually fine if you have a clear, bluish flame. There may be a combustion issue if you notice yellow, sooty-looking flame. ď‚´ Ensure there is no debris outside the furnace. Most people pay attention to cleaning the inside of the furnace and leave the outside unchecked. Do not make this mistake and check the surrounding area for cleanliness and any possible issue. You should be more careful when your furnace is in the attic. The same holds true if your furnace is installed in an area that is exposed to heavy snow. Not cleaning the surrounding area thoroughly would directly affect the efficiency of your furnace, which can shorten its lifespan and increase your energy bills at the same time.


The Right Way to Deal with the Furnace Cleaning  Before getting started with furnace cleaning, you need to pay special attention to your surroundings. Working around a gas appliance has its risks – you may end up sustaining serious injuries due to a leak or fire. Therefore, you should take precautionary measures and ensure you are using the right gear and tools to handle the cleaning task.  Replace the filter of your furnace. One of the most important things to do when cleaning your furnace is to clean its filter. In some cases, the filter can be cleaned and used again, but sometimes, it is better to better have it replaced for better results. Understand that the filter is the only layer of protection against debris and dust. Not using a clean filter would affect the efficiency of the furnace, leading to costly repairs and hefty bills. You do not have to go through a lot of hassle to replace the filter – you can easily find replacement filter at popular home improvement stores. Changing the filter is not tricky either.  Clean the blower properly. After you have replaced the filter, you should turn towards the blower. Cleaning the blower is equally important because it traps any dust and debris that escapes through the filter. You do not need any special tools to clean the blower – all you have to do is clean the blower using a damp cloth. Be sure to wipe down all the belts and pulleys at the same time.


Simple Yet Effective Ways to Select the Best Furnace Repair Technician ď‚´ Choose a reputable service provider. Reputation matters a lot when it comes to hiring a plumbing specialist. While you may want to opt for the cheapest solution, you should not try to cut corners or else you will end up dealing with a bigger problem later. Only experienced and reputable service providers can identify and handle furnace repair correctly. An inexperienced professional may offer a temporary fix to your problems and make you have more repair work in the near future. ď‚´ Be sure to opt for a professional who is there to back their work. It means that they should offer a guarantee with every repair job they handle. At first, every so-called professional promises great repair and installation, but they leave the unsatisfied in the end. Therefore, you should always inquire about the availability of any guarantee. You may have to spend more time to find a company or professional stands behind their work, but it is worth the effort.


Simple Yet Effective Ways to Select the Best Furnace Repair Technician ď‚´ Ask about their training and any certification. You should bear in mind that not all service providers have the right experience and training. Look for a professional or company experienced not only with the manufacturers but also with the equipment they use. You may have to check the company's website to get more details about how experienced and trained a company is. If there is no real information available on their official website, you may want to talk to them directly and ask about their areas of expertise. Keep in mind that HVAC systems are extremely complex, which is why it is not possible for every so-called professional to handle certain furnace repair tasks. So, take your time and get more information about training, experience, and certification of your service provider.

ď‚´ Always select a company only after they have visited your property and evaluated the situation. Professional HVAC contractors know that every furnace repair job is different because of so many underlying factors. Therefore, a true professional would offer a free evaluation to help you get a better idea of the total cost of repair.


Furnace Repair and Replacement: What are the Factors Affecting Replacement Costs? ď‚´ Furnace Types: You need to learn a bit about different furnace types available today. Of course, it is better to have a clue about your budget constraints before you start shopping for a new furnace. You should also do the same when you have a major furnace repair task to take care of. Keep in mind that furnaces vary in the type of energy or fuel they use. You can buy electric furnaces and you can also buy gas and oil furnaces. What works best for you depends directly on your unique household needs. The average cost of a new furnace may vary greatly, but you should expect to pay the least amount of money for electric furnaces. Oil furnaces are usually the most expensive ones, whereas gas furnaces fall somewhere in between electric and oil furnaces. Be sure to explore and compare different options to make a right decision. ď‚´ Furnace Size: The size of your furnace matters a lot and should be selected keeping your unique household need in mind. Opting for a right-sized furnace can save you some good money in energy costs. You will also have to bear with low upfront cost. Bigger furnaces are usually more expensive, which is why you need to ensure that you select a size that is just enough for your family.


Furnace Repair and Replacement: What are the Factors Affecting Replacement Costs?  Furnace Installation: When comparing the cost of furnace repair and furnace replacement, you should consider installation costs as well. Having a new furnace installed by a specialist will cost you money. The cost usually depends on the time it takes to install the furnace. If it is difficult to install your furnace, you are likely to pay more for it. The installation cost will go up if new ductwork is required.  Furnace Efficiency: Furnaces today are highly efficient, and you can choose from a variety of options. You may want to put your money on furnaces with a higher AFUE rating because they are likely to run more efficiently – they can also offer significant cost savings.


The End For more details, please visit: http://smile-hvac.ca/services/

Some Plumbing and Heating Advices You Should Consider  

1. Simple Plumbing and Heating Advice to Keep Things Functional. 2. Plumbing and Heating: Few Things to Remember to Prevent Pipe Bursting. 3...

Some Plumbing and Heating Advices You Should Consider  

1. Simple Plumbing and Heating Advice to Keep Things Functional. 2. Plumbing and Heating: Few Things to Remember to Prevent Pipe Bursting. 3...

Advertisement