Page 1

Sivoia QED速 IR Remotes With Favorite Preset Button Programming Guide


Sivoia QED速 Favorite Preset Remote Programming Guide The Sivoia QED IR Remote with Favorite Preset Button Programming Guide is a supplement to the Sivoia QED Wiring and Programming Guide. This guide describes the programming and setup of the three configurations of IR remotes that have a round silver favorite preset button. The IR Remote can be used to program and control shades/drapes in the system via a drive unit with an IR receiver, an IR Keypad or via the IR reciever in the Contact Closure Interface. The following chart describes the programming steps. Most of the programming can be performed from any of the three IR remotes. The Two Shade Group Remotes (Type C) require additional programming to define the shades/drapes that are assigned to the two sub groups that these can control.

IR Remote Programming Steps for IR Remotes with Favorite Preset Button Type A

Type B

Type C

Single Shade Group Shade and Lighting Two Shade Groups with Favorite Preset with Favorite Preset with Favorite Preset GROUP 1

GROUP 2

Step

Description SVIT-SH-WH SVIT-DR-WH Addressing System

1

2

Assigning Drives to IR Remote Master Group

3

Assigning Drives to IR Remote Sub Groups

4&5

Storing and Locking Presets

6

Individual Level Adjust

P P P P N/A

SVIT-GRX-DR-WH SVIT-GRX-SH-WH SVIT-MIR-SH-WH SVIT-MIR-DR-WH

P P P P N/A

SVIT-SC-BL-WH SVIT-SR-BL-WH SVIT-SH-DR-WH SVIT-SH-SH-WH

P P P P P

Page 1 Sivoia QED速

Favorite Preset Remote

Programming Guide


1

Addressing the system Addressing can be done with type A, B, or C remotes. Note: Prior to addressing the system, all shades/drapes, by default, will respond to all IR Remotes. After addressing, shades/drapes will not respond to any remote until it is assigned to an IR Receiver, IR Keypad or contact closure interface. (H) Press and hold button (T) Tap button

1.1

Enter Programming Mode Aim the Remote at the IR Receiver and Press and Hold Open and Close for 5 seconds. The LED’s on the receiving device will flash

H H

H H

A

H H

B

1.2

1.3

Enter Addressing Mode Aim the Remote at the IR Receiver and tap Open. The LED’s on the drive will flash rapidly until addressed. Addressing is complete when the receiving device starts flashing slowly. The addressing process will take approximately 1 minute.

Exit Addressing Mode Aim the Remote at the IR Receiver and Hold Open and Close for 5 seconds. The LED’s on the drive will stop flashing.

C

T

T

T

A B

C

H H

H H

A

H H

B

C

Page 2 Sivoia QED®

Favorite Preset Remote

Programming Guide


2

Assigning Drives to the Master Shade Group All three types of remotes (A, B and C) can be used to assign shades to the Master Shade Group. However, all shades that are assigned to this group will only respond to the Type A and Type B remotes after this step. Type C remote requires this step, in addition to step 3, to control shades/drapes.

2.1

2.2

2.3

Enter Programming Mode Aim the Remote at the IR Receiver and Press and Hold Open and Close buttons (Type A and B) or both round silver buttons (Type C) for 5 seconds. The LED’s on the receiving device will flash

Enter Master Assignment Mode Aim the Remote at the IR Receiver and tap the Close button (Type A and B) or while holding the bottom round silver button, tap close button (Type C). All unassigned shades/drapes will open and all assigned shades drapes will close.

H H H H H

A

H

B

C

T

T

T

A

H

B

C

Assigning and Un-Assigning Shades/Drapes Select Shade/Drape to Assign Aim the Remote at the IR Receiver and tap the Close button until the desired shade/drape is selected (Tapping the Open button will select shades/drapes in the opposite order). Selected shade/ drape will “wiggle” or move back and forth a few inches continuously.

T

T

T

A

B

C

Then Assign Selected Shade/Drape Aim the Remote at the IR Receiver and tap the Lower button. The wiggling shade/drape will close to indicate it is assigned.

T

T

T

A

Or

B

C Page 3

Sivoia QED®

Favorite Preset Remote

Programming Guide


2

Assigning Drives to the Master Shade Group (continued)

Unassign Selected Shade/Drape Aim the Remote at the IR Receiver and tap the Raise button. The wiggling shade/drape will open to indicate it is unassigned.

T

T

T

A B

C

Or Assign All Shades/Drapes Aim the Remote at the IR Receiver and Press and Hold the Close button for 5 seconds (Type A,B and C). All shades/drapes will close to indicate they are assigned.

H

H

A

H

B

C

Or Unassign All Shades/Drapes Aim the Remote at the IR Receiver and Press and Hold the Open button for 5 seconds (Type A,B and C). All shades/drapes will open to indicate they are unassigned.

2.4

Exit Programming Mode Aim the Remote at the IR Receiver and Press and Hold Open and Close buttons (Type A and B) or both round silver buttons (Type C) for 5 seconds. The LED’s on the receiving device will flash. All shades/drapes will return their previous position.

H

H

H

A B

C

H H H

A

H H H

B

C

Page 4 Sivoia QEDÂŽ

Favorite Preset Remote

Programming Guide


3

Assigning Shades/Drapes to the Two Group Remote (Type C) Complete step 2 before proceeding. Shades/drapes must be assigned to the master group before they can be assigned to subgroups 1 and 2. Shades/drapes assigned to sub group 1 and 2 will still respond to the master shade/drape group commands sent from the type A and B remotes.

For Group 1

3.1

3.2

3.3

Enter Programming Mode Aim the Remote at the IR Receiver and Press and Hold Open and Close buttons for 5 seconds. The LED’s on the receiving device will flash

Enter Assignment Mode Aim the Remote at the IR Receiver and tap the Close button. All unassigned shades/drapes will open and all assigned drapes/ shades will close.

For Group 2

H H H H

C

C

T

T

C

C

Assigning and unassigning shades/drapes Select Shade Aim the Remote at the IR Receiver and tap the Close button until the desired shade/drape is selected (Tapping the open button will select shades/drapes in the opposite order). Selected shade/ drape will “wiggle” or move back and forth a few inches continuously.

T

T

C

C

Then

Page 5 Sivoia QED®

Favorite Preset Remote

Programming Guide


3

Assigning Shades/Drapes to Two Group Remote (continued) Assign Selected Shade Aim the Remote at the IR Receiver and tap the Lower button. The wiggling shade/drape will close to indicate it is assigned.

T

T

C

Or Unassign Selected Shade Aim the Remote at the IR Receiver and tap the Raise button. The wiggling shade/drape will open to indicate it is unassigned.

C

T

T

C

Or

Assign All Shades/Drapes Aim the Remote at the IR Receiver and Press and Hold the Close button for 5 seconds button. All shades/drapes will close to indicate they are assigned.

C

H

H

C

C

Or Unassign All Shades/Drapes Aim the Remote at the IR Receiver and Press and Hold the Open button for 5 seconds button. All shades/drapes will open to indicate they are unassigned.

3.4

Exit Programming Mode Aim the Remote at the IR Receiver and Press and Hold Open and Close buttons for 5 seconds. The LED’s on the receiving device will flash. All shades/drapes will return their previous position.

H

H

C

C

H H

H H

C

C Page 6

Sivoia QEDÂŽ

Favorite Preset Remote

Programming Guide


4

Setting Limits from the IR Remote The Open and Close limits of shades/drapes can be set from any of the three types of IR remotes. The shade/drape must be assigned to the master shade group (for Type A and B) remote or sub group (Type C), to adjust the limit with that remote. (*) Group 1 programming shown on type C remote. To program with Group 2 use Group 2 buttons.

4.1

4.2

4.3

4.4

Enter Programming Mode Aim the Remote at the IR Receiver and Press and Hold Open and Raise buttons for 5 seconds. The LED’s on the receiving device will flash Select Shade/Drape Aim the Remote at the IR Receiver and tap the Close button until the desired shade/drape is selected (Tapping the open button will select shades/drapes in the opposite order). Selected shade/ drape will “wiggle” or move back and forth a few inches continuously.

* H

H

H

H

H

GROUP 2

A C

B

* T

T

T

A

C

B

*

Position the Shade/Drape to the desired limit Aim the Remote at the IR Receiver and Press and hold Raise (or Lower) button until the shade/ drape is in the desired position.

H or H

H or H H or H

A B

C

Storing the limit Open Limit Aim the Remote at the IR Receiver and Press and hold the Open button 5 seconds. The LED’s on the receiving device will flash to indicate the limit is stored. Close Limit Repeat step 4.3. Aim the Remote at the IR Receiver and Press and hold the Close button 5 seconds. The LED’s on the receiving device will turn off to indicate the limit is stored.

Sivoia QED®

H GROUP 1

* H

H

H

A B

C

* H

H

A

Favorite Preset Remote

H

B

C Page 7 Programming Guide


4

4.5

4.6

Setting Limits from the remote (continued)

Setting Limits on Additional Shades/Drapes Repeat steps 4.2 – 4.4

Exit Programming Mode Aim the Remote at the IR Receiver and Press and Hold Open and Raise buttons for 5 seconds. The LED’s on the receiving device will flash

H

*

H

H

H

H

H

A B

C

Page 8 Sivoia QED®

Favorite Preset Remote

Programming Guide


5

Storing Presets The round silver favorite preset button can return the shade/drape to a favorite preset or position when tapped once in normal operating mode. By default the favorite preset is stored midway between the open and close limit. The favorite preset can be changed to a user defined position with the following procedure. (*) Group 1 programming shown on type C remote. To program with Group 2 use Group 2 buttons.

5.1

5.2

6

Position the Shade/Drape to the desired location Aim the Remote at the IR Receiver and Press and hold Raise (or Lower) button until the shade/ drape is in the desired position.

Storing the Favorite Preset Aim the Remote at the IR Receiver and Press and hold the round silver favorite preset button for 5 seconds. The LED’s on the receiving device will flash to indicate the limit is stored.

* H or H

H H or

H or H

A B

C

* H

H

A

H

B

C

Locking Presets The favorite preset can be “locked” to prevent accidental reprogramming of the preset. Locking the presets from the remote or any other device will prevent presets from being accidentally changed from the remote or any other device in the system.

6.1

6.2

Locking Presets Aim the Remote at the IR Receiver and Press and hold Open and the Favorite Preset buttons for 5 seconds. The LED on the receiving device will flash rapidly then turn off to indicate presets have been locked. Unlocking Presets Aim the Remote at the IR Receiver and Press and hold Open and the Favorite Preset buttons for 5 seconds. The LED on the receiving device will flash once then turn off to indicate presets have been unlocked.

Sivoia QED®

H

H

H

H H

A

H

B

C

H

H

H

H H

A

Favorite Preset Remote

H

B

C Page 9 Programming Guide


7

Individual Level Adjust Individual level adjust allows the favorite preset of each of the shades/drapes assigned to a group, to be set at different levels as shown in the following figure.

The presets must be unlocked to perform this step (refer to step 6.2).

7.1

7.2

Enter Individual Level Adjust Mode Aim the Remote at the IR Receiver and Press and hold Open and Lower buttons for 5 seconds. The LED’s on the receiving device will flash. Select Shade/Drape Aim the Remote at the IR Receiver and tap the Close (or Open) button until the desired shade/drape is selected. Selected shade/drape will “wiggle” or move back and forth a few inches continuously.

H

H

H

H H

H

A B

C

T

T

T

A

C

B

Note: For Type C Remotes both Group 1 and Group 2 shades/ drapes can be selected.

7.3

7.4

Position the Shade/Drape to the desired location for the preset Aim the Remote at the IR Receiver and Press and hold Raise (or Lower) button until the shade/ drape is in the desired position.

H or H

H or H H or H

A B

C

Select and set additional shades/drapes Repeat steps 7.2 and 7.3. Page 10

Sivoia QED®

Favorite Preset Remote

Programming Guide


7

7.5

7.6

Individual Level Adjust (continued)

Exit Individual Level Adjust Mode Aim the Remote at the IR Receiver and Press and Hold Open and Lower buttons for 5 seconds. The LED’s on the receiving device will flash the turn off. Storing the Favorite Preset Aim the Remote at the IR Receiver and Press and hold the round silver favorite preset button for 5 seconds. The LED’s on the receiving device will flash to indicate the limit is stored.

H

H

H

H H

H

A B

C

H

H

THEN

A

H

B

H

C

Note: For Type C Remote store presets for both Group 1 and Group 2.

Contact Information Worldwide Headquarters | USA Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299 USA TEL: 1.610.282.3800 FAX: 1.610.282.3090 Technical Support: 1.800.523.9466 or 1.610.282.6701 Toll Free: 1.888.LUTRON EMAIL: shadinginfo@lutron.com WEB: www.lutron.com/ shadingsolutions

Europe Headquarters | United Kingdom Lutron EA Ltd 6 Sovereign Close London, E1W 3JF, UK TEL: +44.(0)20.7702.0657 FAX: +44.(0)20.7480.6899 Technical Support: +44.(0)20.7480.6899 FREEPHONE: 0800.282.107

Asian Headquarters | Singapore Lutron GL Ltd 15 Hoe Chiang Road #07-03 Singapore, 089316 TEL: +65.6220.4666 FAX: +65.6220.4333 Technical Support: 800.120.4491

These products may be covered under one or more of the following U.S. patents: 6,380,696; 6,992,612; 7,142,932; D518,447; D525,948; and corresponding foreign patents. ©2009 LUTRON Electronics Co., Inc. P/N 045-207 REV. A Page 11 Sivoia QED®

Favorite Preset Remote

Programming Guide

Sivoia QED IR Remotes with Favorite Preset Button  

IR Remotes With Favorite Preset Button Sivoia QED ® Type C Type B Type A Individual Level Adjust SVIT-GRX-DR-WH SVIT-GRX-SH-WH SVIT-MIR-SH-W...

Read more
Read more
Similar to
Popular now
Just for you