Page 1


Wash Stations for Car Wash • Truck Wash • Industrial Cleaning

1

All the features you want, in an Easy-to-Service, Compact High Pressure Wash Station!

Prewired Motors & panels

Hour Meter UL Listed Electrical Panels for Each Pump

Liquid-Filled Pressure Gauge

D

Choice of Pumps Stainless Steel Frame & Belt Guards

Pressure Relief Valve

Stainless Stand Holding Tank Stainless Soap & Wax Solenoids

Shown with Optional Foam Brush, Pre-Soak & Engine Tire Cleaner Systems

Flow Control Check & Gate Valves

~ Stations are Pre-Plumbed and Wired ~

Hour Meter

Stacked Pump Station

STATION FEATURES Stainless Supply Tanks with Chemical Mixing Valves

• PUMPS: Direct-drive or Pulley-drive CAT Plunger Pumps are standard. (HYPRO • GENERAL • AR • GIANT are also available). • ELECTRICAL PANELS: High quality, solid state controls for long trouble-free service. (UL Listed). • STAINLESS STEEL SUPPLY TANKS. • MOTOR: 3 or 5 HP, 230 Volt, TEFC, Single or Three phase. (208/460 Volt also available. Leeson & Baldor available).

D

Choice of Pumps Pressure Relief Valve

• TANK HEATER in water tank on stacked units. • SOLENOID VALVES: Stainless Steel solenoid valves for both soap and wax lines. Double inlet design for hot and cold water inlets. • PRESSURE-FEED SYSTEMS feature a single injector valve for both soap and wax solutions. Provides accurate proportioning of soap and wax concentrations.

Stainless Solenoid Valves • GRAVITY-FEED SYSTEMS feature a stainless holding tanks with float valves for uninterrupted water supply. Slide Out • PRESSURE GAUGES: Stainless case, Glycerin-filled gauges for Stainless Trays accurate readings of output pressure.

Separate Control Panels for all Bays (UL Listed)

TEFC motors

• HOUR METER: Ideally suited for indication of pump system running time for maintenance and service requirements.

Liquid-Filled • BALANCED PRESSURE RELIEF VALVE: Allows for the use of trigger Pressure Gauge guns as well as protecting the system against damage from excessive pressures.

Stainless Steel Belt Guards Weep Freeze Prevention

Stainless Steel Frame is Standard on Stacked Units

Direct Drive PUMPING STATIONS Single or Three Phase 3.0 HP: 3.5 GPM @ 1200 PSI 5.0 HP: 4.0 GPM @ 1800 PSI 7.5 HP: 5.0 GPM @ 2200 PSI

Casters are Removeable After Unit is in place

• STAINLESS STEEL FRAME: Constructed with adjustable levelers on each leg. • DIMENSIONS: BENCH MODELS: Height is 34". Overall height is 62". Depth is 29".Width on single bay is 22". Double bay width is 44". STACKED MODELS: Height is 74". Depth is 32". Width is 52". (4-Bay).

nt me p i g u Eq easin le L ilab a Av

Pulley Drive PUMPING STATIONS Single or Three Phase 3.0 HP: 3.5 GPM @ 1200 PSI 5.0 HP: 4.0 GPM @ 1800 PSI 7.5 HP: 5.0 GPM @ 2200 PSI

Call Us for Current Pricing! DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0001


2

Pre-wired UL listed electrical panel with solid state components.

Truck Wash Pumping Stations

Automatic auto shut down for operator control at wand.

Rated Up to 185° F. Water Operating Temperature!!

7-1/2 or 10 hp TEFC motors, single or three phase.

Choice of Pumps • CAT • Emperor • Rated to 4.8 GPM @ 2300 PSI with 7-1/2 HP, 4.8 GPM @ 3000 PSI with 10 HP

D

Stainless Soap & Wax Valves

Stainless holding tank for pump supply.

TRUCK WASH Pumping Stations 7.5 HP: 4.8 GPM @ 2300 PSI 10 HP: 4.8 GPM @ 3000 PSI

Heavy gauge stainless steel frame with self leveling legs

D

Part No.

Pump

Motor

DU PS1701C-PG Single, Emperor DU PS1901C-PG Single, Cat Pumps DU PS1701CPG2 Double, Emperor DU PS1901CPG2 Double, Cat Pumps DU PS1703C-PG Single, Emperor DU PS1903C-PG Single, Cat Pumps DU PS1703CPG2 Double, Emperor DU PS1903CPG2 Double, Cat Pumps

RO Systems, Water Heaters, Trigger Wand Packages Also Available

Economy Wash Packages

7.5 HP / 1 PH 7.5 HP / 1 PH 7.5 HP / 1 PH 7.5 HP / 1 PH 7.5 HP / 3 PH 7.5 HP / 3 PH 7.5 HP / 3 PH 7.5 HP / 3 PH

Output

Net Ea.

4.8 @ 2300 $ 5139.00 4.8 @ 2300 5495.00 4.8 @ 2300 9977.00 4.8 @ 2300 10652.00 4.8 @ 2300 4839.00 4.8 @ 2300 5142.00 4.8 @ 2300 9240.00 4.8 @ 2300 9955.00

D

Economy Wash Packages are the ideal choice for Apartment Complexes, Boat Marinas, Golf Courses and many other venues. An economical way to offer high pressure cleaning to your customers.

Perfect for Apartment Complexes, Boat Marinas, Golf Courses and Many Other Venues!

The EWS10 System is complete with Pump Unit, soap and rinse valves, stainless steel coin meter, stainless wall boom, chemical tank, trigger wand assembly, 25’ wand hose, wall hanger and instruction sign.

D

Three flow rates to choose from: 2 HP Unit will produce 3.0 GPM at 1000 PSI; 3 HP Unit will produce 3.2 GPM at 1300 PSI and 5 HP Unit will produce 3.8 GPM at 1800 PSI. Part No. Motor Net Ea. DU EWS10 Econo Wash Package 2 HP / 1 PH $ 3854.00 DU EWS10-31 Econo Wash System 3 HP / 1 PH 4123.00 DU EWS10-51 Econo Wash System 5 HP / 1 PH 4072.00 * Note: 1 Phase Units Shown, 3 Phase Also Available DULTMEIER SALES

OMAHA, NE (800)

D

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0700


STAINLESS STEEL COIN METERS

3

Precision Die-Cut Stainless cabinets for uniform fit and a finished look 12"

12"

Mega Meters (Bills & Coins) — 10 Position Switches — Mega Bill & Coin Meters accept multiple coins, tokens and bills. Features Digital Timer with LED readout, 10-position rotary switches and electronic multi-coin mechanisms. (12-position also available). Available in vault ready or with built-in coin box. Heavy-gauge Stainless Steel construction. Upper door is hinged for easy access and maintenance.

D

15"

D

Model 25VM-HS Vault Ready

High Security Medeco Screw Lock

23"

Hidden Puck Lock Model 25MMD-HSM with High Security Lock & Shield

Medeco T-Handle Lock & screw lock for added security. Round Part No. Puck Lock on money drawer is DU 23VM virtually “Pick Proof”. DU 23MMD

D

MEGA METER Net Ea.

DU 25VM-HS

Coinco or Mars Bill acceptors can DU 25MMD-HS be set for $1, $5, $10 and $20 DU 25VM-HSM bills if desired. DU 25MMD-HSM

Vault Ready, Coins/Tokens, No Bills................... $ 1474.00 With Coin Drawer, Coins/Tokens, No Bills.......... 1867.00 Vault Ready, COINCO, Bills/Coins/Tokens.......... 1826.00 With Coin Drawer, COINCO, Bills/Coins/Tokens. 2207.00 Vault Ready, MARS, Bills/Coins/Tokens............. 1804.00 With Coin Drawer, MARS, Bills/Coins/Tokens.... 2195.00

Note: 12 Position Meters also available.

Heavy-Duty Stainless Meters

8"

8 & 10 Position, Coin / Token / Credit Card Options Heavy-duty Stainless Steel coin meters with removable front doors for easy access. Standard with stainless steel security bar for extra protection on coin drawer models. Available with either built-in coin drawer or less coin drawer to be used with vault/safe systems. Timers are only included on Digital or Last Alert models, please specify on other models. 16" D

D

Medeco Screw Lock

Optional Stainless Security Bar

Model 10CD-DI with Coin Drawer

Secondary Lock is optional

Standard Features: Screw-style lock for coin drawers • 8-position or 10-position rotary switches • Stainless steel security bars for lower coin drawer • Mechanical or Electronic multi-coin mechanisms • Cam-style lock for upper lid • Recessed and hinged upper lid • 24 volt running light • Plug-in wiring harness • Function Decals • 12 gauge construction • 1000 Quarter capacity in coin drawer models • Dimensions: 8” wide x 11” High x 5-7/8” Deep.

7-7/8"

8 Position, Coin / Token Digital meters feature a high intensity, L.E.D. readout which is easily seen in the bay. With one minute remaining, horn (included) sounds for 5 seconds and then readout flashes for the remaining countdown. Last Alert Meters also count down but do not have visual readout. At one minute horn (included) sounds for 5 seconds alerting customer to add more coins. “Digital” and “Last Alert” Meters are available with either Mechanical or Electronic multi-coin and token mechanisms. Dimensions: 12-7/8" x 7-7/8" x 7-7/8" Timer Type

Mechanism

Wt./Lbs.

11"

Model 10VS-DI Vault Ready

Standard Features: • Stainless Steel Construction • Running light • Cam & Tube Locks • Push-lock plug-in wire harness • 8-Position Rotary Switch • Coin Mechanism • Function Decals • High Security Bar & Lock Guard • 1600 Quarter Capacity in Coin Drawer Models

12-7/8"

Net Ea.

DU 100R-10B * None Mechanical 20 $ 667.00 DU 100R-10DE Digital Electronic 20 1165.00 DU 100R-10DM Digital Mechanical 20 983.00 DU 100R-10LE Last Alert Electronic 20 1165.00 DU 100R-10LM Last Alert Mechanical 20 993.00 * Timer Optional - Order Separately.

D

Part No. Meter Style Coin Mech. Switch Timer Wt./Lbs. Net Ea. DU 10CD Coin Drawer Mechanical 8 * None 20 $ 688.00 DU 10CD-DI Coin Drawer Mechanical 8 Digital 22 966.00 DU 10CD-DIE Coin Drawer Electronic 8 Digital 22 1147.00 DU 10CD-DIE/2 Coin Drawer Electronic 10 Digital 22 1220.00 DU 10CD-DIE2Y Coin Drawer Elec./Credit Card 10 Digital 22 1768.00 DU 10VS Vault/Safe Mechanical 8 * None 18 536.00 DU 10VS-DI Vault/Safe Mechanical 8 Digital 22 808.00 DU 10VS-DIE Vault/Safe Electronic 8 Digital 22 1002.00 DU 10VS-DIE/2 Vault/Safe Electronic 10 Digital 22 1080.00 DU 10VS-DIE2Y Vault/Safe Elec./Credit Card 10 Digital 22 1605.00 * Timer Optional - Order Separately.

High Security Coin Meters

Part No.

8"

D

Model 100R-10B Coin Drawer Model with Security Bar & Lock Cover

E0008


4

STAINLESS STEEL COIN METERS Precision Die-Cut Stainless cabinets for uniform fit and a finished look

Digital Readout

Cryptopay or USA Card Swipes

Coins or Tokens Credit Card Swipe Reader

High Security MEDECO Screw Lock

* Bill Acceptor: Coinco or Mars

Custom Decals

D

Round Lock is hidden for extra security

Bill Only Meters

MEGA METER PLUS Credit Card / Coin / *Bill Meters

Bill Acceptor Bay Meters are designed to be used with your existing bay meters. Simply wire to your meters and accept $1, $5, & $10 or bills in addition to the coins or tokens that you have accepted in the past.You can determine which bills you wish to accept.

D

Model 10BA

COINCO or MARS Bill Acceptors

Hidden “Puck” Lock for Added Security

Dimensions: 12” x 23”

Mega Meters Plus Credit Card Acceptance Designed to accept coins or tokens, $1 to $20 bills and now Master Card, Visa, American Express and Fleet or Gift Cards if desired.These meters can do it all. Available with either lower coin drawer or vault ready versions. Medeco T-Style screw lock for added security on upper door. Hidden RoundStyle lock for coin drawer versions. 10-position rotary switches, digital readout and electronic coin mechanisms are standard. Ready to install. D

Custom Decals

D

DU 50VM Vault Ready (Dimensions: 12” x 15”)

Cryptopay or USA Card Swipes

D

Typical View of 10BA with Existing Coin Meter

Features: • Heavy-duty, Stainless Steel construction. • Enclosed and shielded lock with restricted keys. • Round style lock for extra security. • Hinged door for easy access. • CoinCo or Mars bill acceptors for reliability. • Dimensions are 13" high, 10-1/2" wide and 7-7/8" deep. • Bay functions can be activated from existing meter or Bill Meter. NOTE: Location recommended away from Middle of Bays to limit water overspray.

Part No. Net Ea. DU 10BA Bill Acceptor Meter, COINCO......... $ 869.00 DU 10BA-M Bill Acceptor Meter, MARS............. 887.00

Coinco or Mars Bill Acceptor

Coins/Credit Card, Bills Part No. Coin Drawer Bill Reader DU 50MMD-CY Yes Coinco DU 50MMD-US Yes Coinco DU 50MMD-MCY Yes Mars DU 50MMD-MUS Yes Mars DU 50VM-CY Vault Ready Coinco DU 50VM-US Vault Ready Coinco DU 50VM-MCY Vault Ready Mars DU 50VM-MUS Vault Ready Mars

D

Credit Card Net Ea. Cryptopay Intenet $ 2674.00 USA Wireless 2631.00 Cryptopay Internet 2710.00 USA Wireless 2618.00 Cryptopay Intenet 2295.00 USA Wireless 2235.00 Cryptopay Internet 2311.00 USA Wireless 2248.00

Coins/Credit Card, No Bills Part No. Net Ea. DU 24MMD Coin Drawer None USA Wireless $ 2271.00 DU 24MMD-CY Coin Drawer None Crytopay Internet 2336.00 DU 24VM Vault Ready None USA Wireless 1878.00 DU 24VM-CY Vault Ready None Crytopay Internet 1943.00

Credit Card Meter Add-On Credit Card Meter for selfserve bays. Allows you to continue to use your existing coin meters and also accept credit card payments. Compact design is 11” high x 8” wide. Stainless steel construction.

D

USA Reader

Part No.

Wt.

DU 10CCA-US USA Reader, Wireless............................. 20 lbs. DU 10CCA-CY Cryptopay, Internet.......................... 20 lbs. DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

Net Ea.

$ 784.00 854.00 E0704


Pet Wash / Grooming Systems

5

Pet Wash Centers from Dultmeier Sales! For added revenue and customer satisfaction. Coin, bill or credit card operated units are designed for use in free standing buildings or bay conversions. (Manually operated units are designed for kennels, veterinarians, pet centers, etc). All systems are complete with the following standard features:

Features: • Stainless steel tub with non-slip mat and easy access ramp. • Supply cabinet which houses grooming chemicals and solenoids manifolds. • Extendable ramp for ease of clean up. • Easy clean hair strainer. • Spray wand assembly for grooming chemicals and warm water rinse. • Offerings include Shampoo, Conditioner, Disinfectant, Odor Control, Warm Water Rinse and Warm Air Blow Dry. • Warm Air/Blower Dryer comes with 20’ hose for quiet, clean drying (110 Volt). • Instruction Signs & Decals are included. • (Meter & Start Up Chemical Options are shown below at add-on pricing depending on your application needs). • Dimensions are 96” L x 57” H x 44” W. Height to top of tub is 40”. shampoo

conditioner

rinse

odor control

D

tub disinfect

blow-dry

Chemical & Manifold Cabinet

PG25S-BE with Stairs. Also Available with a Ramp

PG25-BE with Ramp

Requirements: • • • •

1-1/2” Sewer line connection. 120 Volt, 15 amp dedicated power circuit. Recommended 100 sq. ft. floor space required. Wiring connection from Meter location to pet wash control panel. • Wiring connection from Dryer to control panel and to meter location. • Low voltage wiring from meter to control panel.

D

PG25 Equipment Panel

D

Warm Air Dryer D D

Hair Strainer

Part No. Description Wt./Lbs. Net Ea. PN PG25S Pet Wash Center, Front Equip. Panel w/ Stairs............ 200 $ 5634.00 PN PG25S-BE Pet Wash Center, Back Room Equip. Panel w/Stairs... 200 5336.00 PN PG25 Pet Wash Center, Front Equip. Panel. Panel w/Ramp.. 200 5707.00 PN PG25-BE Pet Wash Center, Back Room Equip. Panel w/Ramp.. 200 5509.00 Meter Options: DU 10CD-PG Coin/Token Meter, Digital Readout............................. 20 $ 1170.00 DU 25MMD-PG Coin/Bill/Token Meter, Digital Readout....................... 40 2106.00 DU 50MMD-PGUS Coin/Bill/Credit Card Meter, Digital Readout.............. 40 3387.00 DU EP1SS Manual Control Box................................................... 10 309.50 Chemical Options: TS SH10 Shampoo, 5 Gallon.................................................... 50 $ 128.50 TS CO20 Conditioner, 5 Gallon................................................. 50 72.65 TS DS60 Disinfectant, 5 Gallon................................................ 50 116.50 TS SK50 Odor Control, 5 Gallon............................................... 50 98.50 Other Options: GS 52440 Vacuum / Hair Extractor............................................................. $ 1240.00

Optional Coin, Bill & Token Meter (Credit Card also available)

Pet h s Wa

D

UL Listed Electrical Panel DULTMEIER SALES

OMAHA, NE (800)

228-9666

TS SH10 Shampoo

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0657


Triple Foam Wax Systems

6

Triple Foam Protectant Systems For Self-Serve

Another new profit center for your self-serve wash. Red, Gold and Blue scented protectant products that are “Clear Coat Safe”. The system is designed to “pulse” and vary colors to the bays, applied via a separate wand assembly. Customers see red, gold, and blue colors foaming from the wand and onto their vehicle. Turtle Wax products produce a brilliant shine, keeping customers in the bays longer - and this means more revenue for you.

UL Listed Electrical Panel

All systems include a multi-compartment tank with Hydrominder valves to eliminate hand mixing. A close-coupled pump/motor unit and pulsing solenoids send the colors to the bays where a separate wand and coil hose assembly is used by the customer to “triple foam” their car. Wall mount design saves space.

D

Standard Components Include the Following:

DU TP6T (Wall Mount) Rotary Pump Design

D

TU SS7 Bay Signs are included.

41” SS Wall Boom

D

Wand Assembly with Hose & Holder

D

Triple Wax Systems Are Available in Two Styles:

1) Positive Displacement, Rotary Pump Drive with Stainless Steel Wall Tank and Stainless Wall Panel Note: Dimensions on Tank is 12-1/2” deep x 18” wide x 24” high. Panel is 24” x 24”. 2) Air Diaphragm Pump Drive with Plastic Tanks and Stainless Steel Wall Frame in a more Compact Unit. Note: Dimensions on Air Pump model is 18” deep x 30” wide x 48” high.

UL Listed Electrical Panel

DU TP8T-ST Floor Stand Model

• 3 Compartment Stainless Tank with Solenoids and Hydrominder Valves • Close-Coupled Pump & Motor Unit • Electronic Controller • 3/8" x 15' Bay Hoses • Wand Assemblies with Nozzles • Stainless Steel Wand Holders • Foam Modules, Run Lines and Plumbing for Each Bay • Freeze Prevention Components • Colorful Bay Signs • Start-Up Turtle Wax Products • Stainless Wall Booms

Rotary Pump Drive Part No. No. of Bays

DU TP3T 3 DU TP4T 4 DU TP5T 5 DU TP6T 6 DU TP7T 7 DU TP8T 8

Start-Up Turtle Wax® Products Included

Pump Type

Air Diaphragm Pump Drive Part No. No. of Bays Pump Type

D

DU TP3T-A 3 DU TP4T-A 4 DU TP5T-A 5 DU TP6T-A 6 DU TP7T-A 7 DU TP8T-A 8

DU TP4T-A

Net Ea.

Rotary $ 4178.00 Rotary 4596.00 Rotary 4949.00 Rotary 5429.00 Rotary 5756.00 Rotary 6136.00 Net Ea.

Air $ 4170.00 Air 4356.00 Air 4850.00 Air 5303.00 Air 4887.00 Air 5234.00

Triple Foam Applicator Unit For Conveyors & Automatics Designed to apply 3 different waxes at the same time. Ideal for use as a triple foam applicator system for Automatic or Conveyor Washes. Wall mount design features Air Driven Diaphragm Pumps, Polyethylene Tanks and Stainless Wall Frame. Standard Features Include: Hydrominder valves for automatic mixing • Plastic storage tanks • Stainless wall frame • Gauges for air and chemical pressures • Air Regulators • Air Solenoid • Foamer Modules • 500’ of run tubing from equipment room to existing arch • Dimensions are 18” deep x 30” wide x 36” high. Part No.

DU TFA1

Triple Foam Applicator

Wt.

77 lbs.

Net Ea.

$ 1930.00

D D

TFA1 DU 50FBM Foam Module included with each bay E0013


PreSoak & Foam Systems

7

PreSoak Systems

Foaming Tire & Engine Cleaner Systems

Increase bay revenue and keep customers satisfied with a PreSoak System from Dultmeier Sales. Use as an addition to or in place of foaming brush systems for extra cleaning ability.

Centrifugal Pump Design

Dultmeier Sales PreSoak systems are designed to apply a concentrated cleaning product under medium pressure to the surface of a vehicle. Easily adapts to your existing car wash equipment. Simply tap into your high pressure line to each bay and apply Presoak Cleaner through your standard spray gun. Standard Components include:

Keep your customers in the bays longer, increase revenues and improve customer satisfaction with a Foaming Tire & Engine Cleaner System from Dultmeier Sales. These systems feature Turtle Wax Start Up Tire Cleaner.

D

• Stainless Transfer Pump delivers 180 PSI.

Easily adapts to existing wash equipment. Simply splice into your high pressure discharge lines & tire cleaner product can be applied through a standard spray gun. All fittings and tubing are supplied for chemical and air lines.

• Automatic Stainless Steel Mixing Tank with Hydrominder Mixing Valve. • Stainless Steel Solenoids with metering screws.

UL Listed Electrical Panel

• Pre-wired Electrical Panel.

These systems are designed to “Foam” the tire cleaner product onto the surface of the tire. An air compressor is required but is not included with these units. All Tire & Engine Systems are Pre-Wired, Pre-Plumbed and tested prior to shipment.

• Chemical Tank.

D

• Stainless Steel Support Frame with leveler legs. • High Pressure Check Valves for each bay. • All necessary Tubing and Fittings. • Turtle Wax Start-Up PreSoak.

UL Listed Electrical Panel

Part No.

Pressure No. of Bays

DU PS1-HP DU PS2-HP DU PS3-HP DU PS4-HP DU PS5-HP DU PS6-HP

180 PSI 180 PSI 180 PSI 180 PSI 180 PSI 180 PSI

1 2 3 4 5 6

Standard components include: Stainless Steel Close-coupled Centrifugal Transfer Pump • Turtle Wax Start-Up Chemicals • Automatic Stainless Steel Holding Tank • HydroMinder Mixing Valve • Stainless Steel Solenoids with Metering Screws • Pre-Wired Electrical Panel • Stainless Steel Support Frame with leveler legs • High Pressure Stainless Steel Check Valves for each bay • Foam Modules for each bay • All necessary Tubing and Fittings.

Net Ea.

$ 2117.00 2488.00 2529.00 2638.00 2807.00 2863.00

Optional TU SS4 Bay Sign Available

Optional TU SS8 Bay Sign Available

Foaming PreSoak System

Multiple Product Foam Systems These systems are designed to mix and distribute (3) different products in self-serve bays. Ideal for use with Presoaks, Bug Cleaners, Tire Cleaners, Clear Coat Protectants, Foam waxes, etc. Three, mix and transfer systems in one compact unit. Eliminates the need to have (3) separate systems which lessens space requirements. Note: Single or double product systems are also available.

From Dultmeier Sales! Foaming PreSoak System for added revenue featuring Turtle Wax Start up “PreSoak Chemical”. Customers love the way the presoak covers the entire vehicle with rich foam that clings and helps to clean away dirt. This is a separate system much like a brush system. Product is applied through a separate wand assembly and does not run through the high pressure pump lines. Standard Features Include: Stainless steel stand and tank • Close-coupled pump/motor unit • Hydrominder valve for automatic mixing • Startup chemical • Coil bay hoses with spray wands • Stainless steel wand holders • Supply tubing and fittings • Pre-plumbed and Pre-wired.

Standard Features Include: Automatic mixing tanks • Air regulators with gauges • Stainless wall rack • Stainless bay booms • Run tubing with fittings • Foam modules • Air diaphragm pumps • Foam wands with holders • Pre-plumbed, pre wired and ready for use • Dimensions are 18” deep x 30” wide x 48” high

D

UL Listed Electrical Panel

Part No. No. of Bays Net Ea. DU FPS2 2 $ 2630.00 DU FPS3 3 2731.00 DU FPS4 4 3015.00 DU FPS5 5 3325.00 DU FPS6 6 3636.00 DU FPS7 7 3863.00 DU FPS8 8 4605.00

D

DU 50FBM Foam Module included with each bay

Wand Assembly with Hose & Holder

Optional Bay Sign TU SS4 Available

Part No.

DU 3FP3-3 DU 3FP3-4 DU 3FP3-5 DU 3FP3-6 DU 3FP3-7 DU 3FP3-8

Wand Assembly with Hose & Holder DULTMEIER SALES

Part No. No. of Bays Net Ea. DU TC2 2 $ 2384.00 DU TC3 3 2506.00 DU TC4 4 2706.00 DU TC5 5 2835.00 DU TC6 6 3016.00 DU TC7 7 3140.00 DU TC8 8 3337.00

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

Net Ea.

3-Bay, 3 Product Foam System 4-Bay, 3 Product Foam System 5-Bay, 3 Product Foam System 6-Bay, 3 Product Foam System 7-Bay, 3 Product Foam System 8-Bay, 3 Product Foam System

553-6975

www.dultmeier.com

$ 3439.00 3888.00 4869.00 5695.00 4293.00 4556.00 E0012


Foam Brush Systems

8

Increase Bay Revenue and Keep Customers Coming Back again & again with a Foaming Brush System from Dultmeier Sales. All the Foam Brush Systems featured below are built with high quality valves, solenoids, injectors and regulators. Stainless steel booms are a standard component as is an automatic supply tank for a continuous, accurate supply of foam brush solution. All units are pre-plumbed, pre-wired and ready for hookup.

CENTRIFUGAL PUMP STYLE

Auto Mixing Tank

Standard Components

Foam Brush Systems

• S.S. Close-coupled Centrifugal Pump • Foamer Modules for each Bay

These units feature close-coupled centrifugal pump providing a constant discharge pressure to all bays.

D

Separate air and chemical lines are run from the pump room to the foamer modules which are located out near the bay to reduce “lag time” of foam solution to the brush. Centrifugal Pump Systems are standard with a Stainless steel, automatic mixing tank for an accurate, continuous supply of foam brush solution.

UL Listed Electrical Panel

• Stainless Steel automatic Mixing Tank with “HydroMinder” Valve

A Stainless steel frame supports the mixing tank as well as all of the necessary solenoids and valves.

Start-up Turtle Wax® Products Included

• Stainless Steel Solenoids with metering screws

Bay Instruction Signs (optional)

• Brush Handle Assemblies with hoses and fittings • Stainless Steel Support Frame

No. of Part No. Bays Net Ea. DU FB1-P 1 $ 2647.00 DU FB2-P 2 2995.00 DU FB3-P 3 3575.00 DU FB4-P 4 4024.00 DU FB5-P 5 4508.00 DU FB6-P 6 5008.00 DU FB7-P 7 5207.00 DU FB8-P 8 5804.00

AIR STYLE PUMP

• Turtle Wax® Brush Soap • Pre-Wired Electrical Box • Stainless Steel Wall Booms • Weep System for Freeze Prevention • Hogs Hair Brushes • Brush Buckets to help keep brushes clean • Supply Hoses, Run Tubing & Fittings

Standard Components

• Air Driven Pumping Unit

Foam Brush Systems These systems feature a compressed air driven chemical pump that delivers a constant supply of rich, thick foam for your customers. Pump and solenoids are mounted on a handsome panel that mounts to your pump room wall. Separate supply lines are run from the air and chemical solenoids in the pump room to each of the foam modules which are located out near the bay to reduce “lag time” of foam to the brush.

• • • • • • • • • •

Auto Mixing Tank D

Bay Instruction Signs (optional)

Foamer Modules for each bay Stainless Steel Solenoids with metering screws Brush Handle Assemblies with hoses and swivels Stainless Mixing Tank with “HydroMinder” valve Stainless Steel Wall Booms Turtle Wax® Brush Soap Weep System for freeze prevention Hogs Hair Brushes Brush Buckets to help keep brushes clean Supply Hoses, Run Tubing & Fittings. No. of Part No. Bays Net Ea. DU FB1A 1 $ 1320.00 DU FB2A 2 1707.00 DU FB3A 3 2160.00 DU FB4A 4 2619.00 DU FB5A 5 3061.00 DU FB6A 6 3602.00 DU FB8A 8 4472.00

Start-up Turtle Wax® Products Included

Foam Brush Components Stainless Steel 180° Wall Boom supplied with all units. This heavy-duty boom is made of 304 Stainless steel and is 6 feet long.The discharge coupling is 1/2" FPT. Boom bracket mounts to wall to allow for free 180° movement. 12FBM Equipment Room Foamer

Part No. Net Ea.

Brush System Accessories shown elsewhere in this catalog ! DULTMEIER SALES

OMAHA, NE (800)

228-9666

50FBM Foam Brush Module is the foamer module used in FB-P and FBA Brush Systems. Can be used to convert the old style systems that create foam in equipment room to this type which creates foam in the Bay.

DU 12FBM DU 12FBM-3/8 DU 50FBM

DAVENPORT, IA (800)

Foamer Head Only, Equipment Room, 1/2” Barbs............. Foamer Head Only, Equipment Room, 3/8” Barbs............. Foam Module, In Bay.........................

553-6975

www.dultmeier.com

$ 19.90 20.05 35.00 E0014


WATER SOFTENERS

9

— Multiple Tank —

Alternating Twin-Tank, Triple Tank and Four Tank Automatic Regeneration Water Softeners. Engineered to handle your most demanding commercial/industrial needs. Alternating design means there is always one, two or three tanks that have “soft” water available. Automatic regeneration means there is no time clock to adjust; regeneration occurs when it is required, saving you money. features Include: 5-cycle control valve with 1" ports assures a continuous 24-hour supply of conditioned “soft” water. • Flow rates as high as 75 GPM. • Standard with (2, 3 or 4) resin tanks, (1 or 2) salt brine tanks and control valves. • Rated to pressures up to 120 psi. • Temperatures to 100° F. • Standard 110 volt. (24 volt or 220 volt also available.)

FEATURES:

Braswell Control

• Regeneration is triggered as needed, not on a fixed schedule.

• Tanks operate independently to deliver an uninterrupted supply of soft, high-quality water.

• Downflow service draws softened water from the cleanest part of the resin bed.

• Handles the hardest water and removes heavy metals.

• FLECK or BRASWELL Controls

• Efficient five-cycle upflow regeneration uses less salt & water.

• Two Year Limited Warranty FLECK 9100SXT Control

Pre-Plumbed Manifolds are Optional

D D

D

D

FC-60-T9000

FC-108-T9000 Braswell Control Valve

Braswell Electronic Controller

Capacity Requirements: = Grains of Hardness + PPM Iron x Maximum Total Gallons used per day.

Mounted in Series for Higher Flow Rates

Mineral Brine Tank Peak Maximum Tanks Size Salt Flow Grains Wt. (Dia x H) (Dia x H) Storage Lbs. GPM Per Tank Lbs. Net Ea.

Twin Tank Units DU FC-36-T9000 DU FC-40-T9000 DU FC-48-T9000 DU FC-60-T9000 DU FC-90-T9000 DU FC-95-T9000 DU FC-100-T9000 DU FC-108-T9000 DU FC-120-T9000 DU FC-130-T9000 DU FC-150-T9000 DU FC-240-T9000

8 x 44 * 8 x 44 * 9 x 48 9 x 48 10 x 54 * 10 x 54 12 X 48 * 12 x 52 13 x 54 * 13 x 51 * 14 x 65 * 16 x 65

18 x 33 18 x 30 18 x 30 18 x 33 18 x 33 18 x 30 24 x 41 18 x 30 24 x 41 21 x 35 21 x 35 21 x 35

350 300 300 350 350 300 700 300 700 550 550 550

8 10 13 12 15 14 16 15 20 15 15 15

22,500 x 2 22,500 x 2 30,000 x 2 30,000 x 2 45,000 x 2 45,000 x 2 60,000 x 2 60,000 x 2 78,000 x 2 75,000 x 2 90,000 x 2 120,000 x 2

140 150 180 225 290 250 365 330 435 375 470 625

$ 959.00 834.00 849.00 964.00 1141.00 929.00 1351.00 1059.00 1548.00 1195.00 1368.00 1598.00

NOTE: Units can be mounted in series to double flows if required. (E.G. (2) FC-60 units will flow 26 GPM. * Fleck 9100 Control with 3/4” meter and 1” distributor pipe.

Mineral Brine Tank Peak Maximum Tanks Size Salt Flow Grains Wt. (Dia x H) (Dia x H) Storage Lbs. GPM Per Tank Lbs. Net Ea.

Triple Tank Units DU FC1054T 10 x 54 DU FC1054FL *10 x 54 DU FC1248T 12 x 48 DU FC1252FL *12 x 52 DU FC1354T 13 x 54 DU FC1354FL *13 x 54

24 x 41 24 x 40 24 x 41 24 x 40 24 x 41 24 x 40

700 675 700 675 700 675

420 450 520 630 730 705

$ 2261.00 2517.00 2707.00 2669.00 2977.00 2935.00

30 30 40 40 50 50

45,000 x 3 45,000 x 3 60,000 x 3 60,000 x 3 78,000 x 3 80,000 x 3

Peak Flow GPM

Maximum Grains Wt. Per Tank Lbs. Net Ea.

60 60 75 75

60,000 x 4 60,000 x 4 78,000 x 4 80,000 x 4

* Fleck 7000 Control Valves

We Have Larger Systems Available — Call for Pricing!

Mineral Tanks (Dia x H)

Four Tank Units DU FC1248-4 12 x 48 DU FC1252FL * 12 x 52 DU FC1354-4 13 x 54 DU FC1354-4FL * 13 x 54 * Fleck 7000 Control Valves EP SFT04 EP SFT05

DULTMEIER SALES

OMAHA, NE (800)

Brine Tank Size Salt (Dia x H) Storage Lbs.

(2) 24 x 41 (1) 24 x 40 (2) 24 x 41 (1) 24 x 40

1400 675 1400 700

720 840 990 940

$ 3503.00 2669.00 3858.00 3883.00

1 Cubic Ft. Carbon as replacement..................................................... $ 64.50 1 Cubic Ft. Resin as replacement ....................................................... 69.95

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0017


SPOT FREE

Complete Spot Free Rinse Systems. “RO”Production and Transfer Systems so that you can now offer Spot-Free water in your car wash with a reasonable investment. Your Customers will love the very spot-free water. Carbon bottles are standard, but also available for existing systems for chlorine removal.

Rinse Systems

Complete Systems include the appropriate Production Unit with chlorine carbon bottle, 200 Gallon Storage Tank with auto shut-off, Transfer System for the required number of bays, and all hose, valves and fittings to tie these three systems together. (Pre-wired & tested).

SFR Complete RO Systems

UL Listed Electrical Panels

Part No. Complete RO Systems

DU SFR-1HPA DU SFR-2HPA DU SFR-TU DU SFR-1 DU SFR-2 DU SFR-3 DU SFR-4 DU SFR-5 DU SFR-6 DU SFR-7 DU SFR-8 DU SFR-1/1 DU SFR-2/1 DU SFR-3/1 DU SFR-4/1 DU SFR-5/1 DU SFR-6/1

D

D D

D D

Carbon Bottle Storage Tank

(with Auto Back Wash) (L0005FL / L0006FL / L0007FL)

Transfer

Part No.

DU RO250-3 DU RO250-4 DU RO250-5 DU RO250-6 DU RO250-7 DU RO250-8 DU RO250-9 EP L0005FL EP L0006FL EP L0007FL

Net Ea.

1-High Pressure Automatic..... 2200 $ 6378.00 2-High Pressure Automatic..... 4400 9589.00 Tunnel Wash........................... 6600 9149.00 1-Bay Self-Serve System........ 800 4596.00 2-Bay Self-Serve System........ 800 4968.00 3-Bay Self-Serve System........ 800 5687.00 4-Bay Self-Serve System........ 800 5759.00 5-Bay Self-Serve System........ 800 5842.00 6-Bay Self-Serve System........ 800 6004.00 7-Bay Self-Serve System........ 900 6220.00 8-Bay Self-Serve System........ 900 6385.00 1-Bay Self-Serve, 1 Automatic 2200 6220.00 2-Bay Self-Serve, 1 Automatic 2200 6379.00 3-Bay Self-Serve, 1 Automatic 2200 6661.00 4-Bay Self-Serve, 1 Automatic 2200 6828.00 5-Bay Self-Serve, 1 Automatic 2200 6989.00 6-Bay Self-Serve, 1 Automatic 2200 7096.00

TRANSFER SYSTEMS ONLY

These are the systems that produce your spot-free water. Available from 600 to 8700 gallon per day production capacities.

*Gallons Per Day

* Based on 24-hour period and 77° F. Inlet Water Temperature.

Production

RO PRODUCTION SYSTEMS ONLY Features: Stainless Steel Frame • Carbon chlorine filter with automatic backwash feature. • Flow meters for concentrate and permeate levels. • 10 micron prefilters. • Liquid level control for RO water holding tank. • Stainless Steel stands • Automatic & manual backwash feature for a d d e d m e m b ra n e life. • Replaceable Thin-Film Composite membranes. • Preplumbed, pre-wired and tested prior to shipment. Designed to deliver 180 psi to the membranes. Systems up through 800 gpd are 39" H x 15" W x 13" D. Systems rated from 2200 to 8700 gpd are 54" H x 28" W x 24" D. 11,000 GPD unit is stainless wall mount frame.

10

These are the systems that transfer RO Water to the bays. Designed to deliver between 175 and 200 psi.

RO250-7

Features include: Stainless steel transfer pumps • Stainless steel solenoids • Stainless Steel Frame • Stainless & plastic connection fittings • Pre-plumbed, pre-wired and tested prior to shipment • Bay instruction signs (except on SFS-RA & SFS-TU) • Run lines and connection fittings • Power supply "on" light is standard. D

Specifications: SFS-10, 20, & 30 Systems are 11" W x 18" D x 38" H. All other systems are 11" W x 24" D x 38" H. UL Listed

D

Electrical Panel

D

Part No. DU SFS-10 DU SFS-20 DU SFS-30 DU SFS-40 DU SFS-50 DU SFS-60 DU SFS-70 DU SFS-80 DU SFS-100

Chlorine Carbon Bottle with Auto Back Wash (L0005FL/L0006FL/L0007FL)

*Gallons Per Day

800 900 2,200 4,400 6,600 8,800 11,000

UL Listed Electrical Panel

HP

1/4 1/4 1-1/2 1-1/2 3 3 3

Volts

110 110 110/230 110/230 208/230 208/230 208/230

Wt.

Net Ea.

55 lbs. $ 2686.00 60 lbs. 2784.00 100 lbs. 3288.00 125 lbs. 4540.00 155 lbs. 5330.00 175 lbs. 5906.00 200 lbs. 8345.00

3/4 Cubic Ft. Carbon Filter as Replacement.... 75 lbs. 1 Cubic Ft. Carbon Filter as Replacement....... 80 lbs. 2 Cubic Ft. Carbon Filter as Replacement....... 145 lbs.

* Output production is for a 24 hour period and assumes 77° input water. DULTMEIER SALES

OMAHA, NE (800)

395.00 418.00 578.00

228-9666

Self Serve Transfer Systems GPM 1 Bay Self Serve, 3/4 hp, 110V................. 4 2 Bay Self Serve, 3/4 hp, 110V................. 4 3 Bay Self Serve, 1 hp, 110V/230V........... 5 4 Bay Self Serve, 1 hp, 110V/230V........... 5 5 Bay Self Serve, 1-1/2 hp, 110V/230V..... 8 6 Bay Self Serve, 1-1/2 hp, 110V/230V..... 8 7 Bay Self Serve, 1-1/2 hp, 110V/230V..... 8 8 Bay Self Serve, 2 hp, 110V/230V........... 8 10 Bay Self Serve, 2 hp, 110V/230V ........ 12

SFS-40

PSI Wt. Net Ea. 200 50 lbs. $ 1385.00 200 55 lbs. 1753.00 208 60 lbs. 2441.00 208 140 lbs. 2511.00 210 160 lbs. 2592.00 210 160 lbs. 2746.00 210 160 lbs. 2855.00 212 160 lbs. 3019.00 212 200 lbs. 3358.00

Part No. Combo Transfer Systems GPM PSI Wt. Net Ea. DU SFS-RA/1 1 Bay Self Serve, 1 Automatic, 2 hp, 110V. 8 212 125 lbs. $ 2425.00 DU SFS-RA/2 2 Bay Self Serve, 1 Automatic, 2 hp, 110V. 8 212 125 lbs. 2590.00 DU SFS-RA/3 3 Bay Self Serve, 1 Automatic, 3 hp, 230V. 14 175 140 lbs. 2872.00 DU SFS-RA/4 4 Bay Self Serve, 1 Automatic, 3 hp, 230V. 14 175 140 lbs. 3036.00 DU SFS-RA/5 5 Bay Self Serve, 1 Automatic, 3 hp, 230V. 14 175 140 lbs. 3198.00 DU SFS-RA/6 6 Bay Self Serve, 1 Automatic, 3 hp, 230V. 14 175 145 lbs. 3308.00 DU SFS-RA/8 8 Bay Self Serve, 1 Automatic, 3 hp, 230V. 14 175 145 lbs. 3691.00 DU SFS-RA Rinse Arch or Single Automatic, 1-1/2 hp, 230V 8 210 125 lbs. 2155.00 DU SFS-TU Tunnel Arch, Conveyors, 3 hp, 230V.......... 14 175 140 lbs. 2363.00 * Please Specify Voltage. DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0015


11

Reverse Osmosis & Water Filter Components Filmtec Membranes

Dow/Filmtec, Thin Film Composite Membranes are common replacements for a wide variety of Reverse Osmosis Systems. Spiral wound, thin film composite membranes offer better rejection of dissolved solids, can operate at lower pressures and produce more water faster than other types of membrane construction. Rejection rates of 99% are standard.

Membrane Housings

D

Replacement Housings for Membranes in RO Spot Free Rinse Systems. Available in PVC, Fiberglass or Stainless Steel construction. Standard sizes are for 2-1/2" or 4" diameter membranes. All housings come complete with end plugs and o-rings. PVC housings are rated to 200 PSI, fiberglass are rated to 300 PSI and stainless are rated to 300 PSI.

Available in Tap Water (Treated water supply), Brackish Water (Untreated ground or surface water supply) and Seawater models. For tap water applications, Chlorine filters should be used prior to the membrane for increased life. Contact us for options. Extra Low (XLE) and Low Energy (LE) membranes can operate at lower input pressures than standard membranes. Membrane performance is greatly affected by water temperature. Flow rates shown are based on 77° F. input water temperature. Example: (50° F. input temperature can reduce flow rates as much as 40%). Higher input temperatures will increase flow. Production rates are based on a 24 hour day. All membranes are rated to 113° F. Tap Water and Brackish Water models are rated to 600 PSI. Seawater models are rated to 800 PSI. Sizes are either 2-1/2” x 4” O.D. x length.

D

D

FIBERGLASS

STAINLESS

PVC

D

D

For Membrane Part No. Material O.D. Length

EP HE002 PVC 2-1/2" EP HE003 PVC 2-1/2" EP HEG02 Fiberglass 2-1/2” EP HEG03 Fiberglass 2-1/2” EP HEG05 Fiberglass 4” EP HEG06 Fiberglass 4” EP HES02 Stainless 2-1/2" EP HES03 Stainless 2-1/2" EP SS421 Stainless 4" EP SS440 Stainless 4" Part No.

Type

Size

EP ETT06 Tap Water EP ETT07 Tap Water EP ETT08 Tap Water EP ETT10 Tap Water EP ETT11 Tap Water EP XLE2540 * Tap Water EP XLE4021 * Tap Water EP XLE4040 * Tap Water EP LE4040 * Tap Water EP BW2540 Brackish EP BW4040 Brackish EP SW302540 Seawater EP SW304040 Seawater

* Flow Rate

2-1/2” x 14” 2-1/2" x 21" 2-1/2" x 40" 4" x 21" 4" x 40" 2-1/2” x 40” 4” x 21” 4” x 40” 4” x 40” 2-1/2” x 40” 4” x 40” 2-1/2” x 40” 4” x 40”

Net Ea.

200 GPD @ 225 PSI $ 139.50 325 GPD @ 225 PSI 157.50 850 GPD @ 225 PSI 169.50 900 GPD @ 225 PSI 259.50 2400 GPD @ 225 PSI 261.00 850 GPD @ 100 PSI 187.00 1025 GPD @ 100 PSI 235.00 2600 GPD @ 100 PSI 276.00 2500 GPD @ 100 PSI 269.00 850 GPD @ 225 PSI 197.50 2400 GPD @ 225 PSI 268.00 700 GPD @ 800 PSI 195.00 1950 GPD @ 800 PSI 575.00

Net Ea.

21" $ 62.95 40" 68.50 21” 87.50 40” 90.95 21” 99.50 40” 97.95 21" 65.75 40" 80.95 21" 71.95 40" 93.95

dultmeier.com

* Low Energy Membranes.

Thin Film RO Membranes These RO Membranes offer the industry’s leading patented membrane technology. Our buying power allows us to offer these high quality membranes at reduced pricing to you. Exact replacements for Film-Tec, Osmonics and many others in the market. Individually tested before shipping.Temperatures to 110° F. Pressures to 225 PSI. 99.7% salt rejection. (For tap water applications).

• Shop and Order On-Line 24 Hours a Day, 7 Days a Week! • Large Inventories of Over 3 Million Total Items! • View Current Pricing! • Web Specials and Bargain Corner! • Know Your Part Numbers? Use the Web Quick Order Page!

D

• Hundreds of Parts List Schematics (and more to come!) • Technical Library packed with information!

Part No.

Size

* Flow Range

EP HR2540 2-1/2” X 40” 800 GPD @ 225 PSI EP HR4021 4” x 21” 1050 GPD @ 225 PSI EP HR4040 4” x 40” 2000 GPD @ 225 PSI * 24 Hour production cycle at 77° F. tap water. DULTMEIER SALES

OMAHA, NE (800)

Net Ea.

• See New Items not Shown in Our Printed Catalogs!

$ 147.50 158.00 225.00

228-9666

• Track Your Order Status and History! • Secure Site for Safe On-Line Ordering. •

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0016


Reverse Osmosis & Water Filter Components Multi-Purpose Filter Housings

Chlorine Carbon Filters

Rugged, corrosion-resistant plastic filter housings for long, trouble-free life. Used with sediment or carbon cartridges (shown separately) in water systems or as a pre-filter in Reverse Osmosis Systems to protect RO Membranes.

Carbon Filters are designed for removing Chlorine from water supplies prior to Reverse Osmosis systems. Chlorine can damage RO membranes and shorten life. All units are standard with Fleck controls. Units are filled, bedded and ready-forhookup. Connection is 3/4” on L0005 and L0006. Connection is 1” on L0007 and L0008. Backwash feature is time clock activated.

Blue upper housing and white opaque lower bowl. Standard with 3/4" FPT ports. Rated to 125 PSI and 115° F. Standard with pressure vent to allow for easy depressurizing and quick air venting.

D

Chlorine Carbon Bottle with Auto Back Wash

D

WR32 Filter Wrench

Sediment Cartridge Filters

Part No.

Polypropylene String Wound or Spun Filter Cartridges. For replacement in all commercial single or multicartridge housings. Design provides clean, fresh water to RO Membranes or faucets. Filters impurities from 1 to 50 microns. Lengths shown will fit 10" or 20" filter housings. Rated service flows from 5-8 GPM. Diameter on these filters is 2-1/2" O.D. (Fits WF housings on adjacent page.)

D

Spun Style

String Wound

D

D

Service Part No. Cu. Ft. Size Flow Rate Wt. Net Ea. EP L0005FL 3/4 8” x 44” 1-2 GPM 75 lbs. $ 395.00 EP L0006FL 1 9” x 48” 1-3 GPM 80 lbs. 418.00 EP L0007FL 2 12” x 52” 2-6 GPM 145 lbs. 578.00 EP L0008 3 14” x 65” 3-9 GPM 200 lbs. 632.00

D

12

For Cartridge Size

Net Ea.

EP WF1124 12" 5" 9-3/4" x 2-1/2" EP WF2124 22" 5" 20" x 2-1/2" EP WR32 Filter Wrench........................................ EP G101-01 Gasket as replacement .......................

Length

Width

$ 12.50 18.80 3.16 .95

dultmeier.com

* Std Part No. Style Lgth Pkg Net Ea. EP LP012 1 Micron Cartridge String 10" 40 $ 2.15 EP LP014 1 Micron Cartridge String 20" 25 4.25 EP LP013 5 Micron Cartridge String 10" 50 2.15 EP LP015 5 Micron Cartridge String 20" 25 4.25 EP LP017 20 Micron Cartridge String 10" 50 2.15 EP LP019 20 Micron Cartridge String 20" 25 4.25 EP LP024 1 Micron Cartridge Spun 10" 50 1.10 EP LP025 1 Micron Cartridge Spun 20" 25 1.99 EP LP026 5 Micron Cartridge Spun 10" 50 1.10 EP LP027 5 Micron Cartridge Spun 20" 25 1.98 EP LP021 50 Micron Cartridge Spun 10" 50 .99 EP LP023 50 Micron Cartridge Spun 20" 25 1.99 *Std Pkg Orders receive an additional 10% discount

Carbon Cartridge Filters

• Shop and Order On-Line 24 Hours a Day, 7 Days a Week!

Low Flow Carbon Filters for removing chlorine from water supplies prior to RO systems. Protects and extends membrane life. Size is 2-1/2” O.D. x 9-3/4” or 20” length. Fits common blue or white filter housings. Rated to 1 GPM, 5 micron. Temperatures from 50° to 125° F. NSF rated. * Std Part No. Size Pkg Net Ea. EP CFC01 9-3/4” x 2-1/2” 20 $ 3.95 EP CFC05 20” x 2-1/2” 12 7.40 *10% Discount if Ordered in Standard Packages

DULTMEIER SALES

OMAHA, NE (800)

• Large Inventories of Over 3 Million Total Items! • View Current Pricing! • Web Specials and Bargain Corner! • Know Your Part Numbers? Use the Web Quick Order Page! • Hundreds of Parts List Schematics (and more to come!) • Technical Library packed with information!

D

• See New Items not Shown in Our Printed Catalogs! • Track Your Order Status and History! CFC01 Filter

228-9666

• Secure Site for Safe On-Line Ordering.

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E1026


PRESSURE WASHERS

13

(PRESSURE FEED)

Designed with Soap Injectors for High Pressure Soap Injection

Versatile, high pressure wash units. Ideal for a wide variety of cleaning requirements. Features Ceramic Plunger Pumps and 3 or 5 HP TEFC motors. Close-coupled feature eliminates the need for belts or pulleys and provides for smooth, quiet operation.

3 & 5 HP PRESSURE WASH UNITS 3-HP Units are rated to 3.6 GPM @ 1200 PSI. Available with either Cat Pumps® or General/Interpump Plunger pumps. Wash units are complete as shown and include a manual chemical injector and rinse/soap valve for accurate injection of detergents into the system.

Model PMC1553 5 HP Unit

5-HP Units are rated to 4 GPM @ 1800 PSI. Available with either Cat Pumps® or General/Interpump Plunger pumps. Wash units are complete as shown and include a chemical injector and rinse/soap valve for accurate injection of detergents into the system.

D

Standard with pressure unloader valve, trigger style shut-off gun, insulated extension, 50' of 3/8" high pressure hose, gun swivel, pressure pop-off valve, pressure gauge and spray nozzle. All units are pre-assembled on heavy gauge stainless steel base plates and are tested prior to shipping. Part No.

HP PHASE

VOLTS

PUMP

PSI GPM

WT.

Net Ea.

DU PM1301C 3 Single 115/230 Cat 1200 3.6 100 lbs. $ 2184.00 DU PM1303C 3 Three 230/460 Cat 1200 3.6 90 lbs. 1837.00 DU PM1201B-G 3 Single 115/230 General 1200 3.6 100 lbs. 1776.00 DU PM1203B-G 3 Three 230/460 General 1200 3.6 90 lbs. 1529.00 DU PMC1551 5 Single 230 Cat 1800 4.0 160 lbs. 2165.00 DU PMC1553 5 Three 230/460 Cat 1800 4.0 135 lbs. 1888.00 DU PM1251B-G 5 Single 230 General 1800 4.0 160 lbs. 1955.00 DU PM1253B-G 5 Three 230/460 General 1800 4.0 135 lbs. 1712.00 CE M1P018-C-B0S Motor Starter, 3 HP - 1 Phase, 230 volt................. 206.83 CE M2P032-C-B3S Motor Starter, 5 HP - 1 Phase, 230 volt................. 315.05 CE M1P009-C-A9 Motor Starter, 3 HP - 3 Phase, 230 volt................. 183.48 CE M1P018-C-B0 Motor Starter, 5 HP - 3 Phase, 230 volt................. 207.00

Motor Starters Optional

Giant & Hypro Pumps also available!

ELECTRIC DRIVE PRESSURE WASHERS Electric Motor Driven Pressure Washers with Hand Carry, Wall Mount or Wheeled Cart options. High quality AR or General Plunger pumps (Cat Pumps are optional on many models). Standard Features Include: Aircraft grade, tubular aluminum frames • Pressure unloader valve • Thermo sensor valve • Chemical injector • 50’ Hose • Spray wand with quick coupler nozzles • 1-1/2 HP through 3 HP models can ship via UPS with minor assembly required • 6 HP and larger units ship via truck • Wheeled cart models feature pneumatic tires and shock absorbing feet • 115 Volt models include 36’ GFCI power cords • 230 Volt models include 12’ power cord without plug. (Optional Motor Starters are available if needed).

Model HC2015G Electric Hand Carry

D

A suffix at end of part number is AR Pump, G suffix is General Pump Electric Hand Carry Models Part-No. GPM PSI

BI HC2015G BI HC3010G BI HC3015G

2.0 3.0 3.0

1500 1000 1500

Motor

Wt.

2HP / 115V / 1PH 2HP / 115V / 1PH 3HP / 230V / 1PH

98 lbs. 98 lbs. 125 lbs.

Electric Wall Mount Models Part-No. GPM PSI

BI WM2015G BI WM3010G BI WM3015G BI WM4020A

2.0 3.0 3.0 4.0

1500 1000 1500 2000

Motor

Wt.

2HP / 115V / 1PH 2HP / 115V / 1PH 3HP / 230V / 1PH 6HP / 230V / 1PH

98 lbs. 98 lbs. 125 lbs. 230 lbs.

Electric Wheeled Cart Models Part-No. GPM PSI

BI EE2015G BI EE3010G BI EE3015G BI EE4020G BI EE3530A BI EE4030A BI EE4035A BI EE3540A

2.0 3.0 3.0 4.0 3.5 4.0 4.0 3.5

1500 1000 1500 2000 3000 3000 3500 4000

Motor

Wt.

2HP / 115V / 1PH 2HP / 115V / 1PH 3HP / 230V / 1PH 6HP / 230V / 1PH 7.5HP / 230V / 1PH 7.5HP / 230V / 1PH 10HP / 230V / 1PH 10HP / 230V / 1PH

105 lbs. 105 lbs. 130 lbs. 235 lbs. 250 lbs. 250 lbs. 265 lbs. 265 lbs.

DULTMEIER SALES

OMAHA, NE (800)

Net Ea.

$ 807.00 809.00 982.00

Model WM2015G Wall Mount

D

Net Ea.

$ 833.00 829.00 1008.00 1839.00

Net Ea.

$ 877.00 875.00 1052.00 1798.00 2155.00 2085.00 2285.00 2295.00

228-9666

D

Model EE2015G Electric Wheeled Cart

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0004


WASH PREP SYSTEMS

14

(GRAVITY FEED)

Designed to be gravity-fed from a premixed supply tank. Ideal for tunnel wash applications where a constant soap solution is used to “Prep” the cars.

DIRECT DRIVE

PULLEY DRIVE PM820D

Double Gun Prep Units Easily prep cars from both sides of the vehicle with the PM820D Wash Units. Ideal for tunnel wash applications. Four choices of pumps available. D

D

Direct-Drive, High Pressure Cleaning Units featuring Cat Pumps® Plunger Pumps and 3-HP or 5-HP, TEFC motors. Rated output is 3.6-GPM @ 1300 PSI on 3-HP units and 4-GPM @ 1800 PSI on 5 HP units. Standard Features Include: Close-coupled Cat Pumps® to TEFC Motors. Pressure unloader valve • Glycerin-filled pressure gauge • Trigger style spray gun • Insulated extension • 25' high pressure hose assembly • Hose swivel • Heavy gauge, stainless steel baseplate • Pressure Pop-off valve. (Note: Low voltage, water-proof, safety switch and motor starter are not included, but can be ordered separately). Part No. Motor Volts PSI GPM Wt. Net Ea. DU PM1301P 3-HP 1-Phase 230 1300 3.6 100 lbs. $ 2104.00 DU PM1303P 3-HP 3-Phase 230/460 1300 3.6 90 lbs. 1623.00 DU PM1551P 5-HP 1-Phase 230 1800 4.0 160 lbs. 2001.00 DU PM1553P 5-HP 3-Phase 230/460 1800 4.0 135 lbs. 1801.00 DU WT15B-ST Tank/Frame as Add-On ...................................... 989.00

Part No.

Pump

CAPACITY

D

Model PM820D-A

Wt.

Net Ea.

DU PM820D Cat 1000 psi @ 10 gpm (5 each Gun) 295 lbs. $ 3286.00 DU PM820D-TS * Cat 1000 psi @ 10 gpm (5 each Gun) 295 lbs. 4765.00 DU PM820D-A Arimitsu 1000 psi @ 10 gpm (5 each Gun) 300 lbs. 2582.00 DU PM820D-G General 1200 psi @ 10 gpm (5 each Gun) 310 lbs. 2678.00 DU PM820D-H Hypro 1300 psi @ 8 gpm (4 each Gun) 300 lbs. 2418.00 DU PM820D-T Giant 1500 psi @ 7 gpm (3.75 each Gun) 285 lbs. 2595.00 * Complete with Poly Tank, Stainless Frame & Auto Mix Valve.

* Please Specify Voltage.

Auto ShutDown Control Panels Designed for use with a wide variety of Prep Units and Pump Systems to automatically shutdown pump and motor when trigger guns are shut-off. Systems include a delay timer to set shut-off to occur when you want it, (i.e. 20 seconds, 1 minute, etc.). All panels include motor starters rated to the required horsepower. Panels are also standard with hour meter, flow switch for pump, multi volt transformer, relays and 14" x 12" gasketed enclosure. All panels have push button start and are pre-wired prior to shipment. U.L. listed.

Standard Features Include: 3-Phase, 7-1/2 HP, TEFC Motor • Pressure Regulator • Pulsation Dampener Hose (Cat or General Only) • Belt tightener • (2) Trigger spray guns with extensions and swivels • (2) 25' hose assemblies • Glycerinfilled pressure gauge • Heavy duty stainless steel baseplate w/ belt guard • Safety pop-off valve • Pre-plumbed and tested prior to shipment. (Motor Starters are optional).

100879 Flow Switch is Included

Single Gun Prep Units

D D

Model PM310-5 Pulley Drive Prep Unit

Pulley driven prep units featuring the popular and proven CAT plunger pumps. Available in 3.5 GPM @ 1300 PSI or 4 GPM @ 1800 PSI. Ideal for use in tunnel wash or Automatic applications. Standard Features: Cat Pumps® Plunger Pump - 3 HP or 5 HP, TEFC motor • Unloader valve for pressure relief • Belt tightener • Heavy gauge stainless steel baseplate • S.S. Belt guard • 50' high pressure gun hose • Trigger style spray gun • Insulated extension • Glycerin-filled pressure gauge • Gun swivel. Units are preplumbed and tested prior to shipment. (Motor starters are available as an option if required).

D

Part No.

DU EP50A-51 DU EP50A-53 DU EP50A-71 DU EP50A-73 DU EP50A-91 DU EP50A-93 DU TDB24AL IP 100879

HP

Voltage

Wt.

Net Ea.

PM310-5/2

5 1 phase, 230V 20 lbs. $ 1135.00 5 3 phase, 208/230/460V 20 lbs. 1078.00 7-1/2 1 phase, 230V 20 lbs. 1137.00 7-1/2 3 phase, 208/230/460V 20 lbs. 1113.00 10 1 phase, 230V 20 lbs. 1119.00 10 3 phase, 208/230/460V 20 lbs. 1129.00 Delay Timer as replacement................ 74.50 Flow Switch as replacement................ 91.40 DULTMEIER SALES

OMAHA, NE (800)

228-9666

Part No.

Motor

DU PM270-3 DU PM270-31 DU PM310-5 DU PM310-51 DU PM310-5/1 DU PM310-5/2

3 HP 230/460 3 3.5 1300 120 lbs. $ 1819.00 3 HP 230 1 3.5 1300 120 lbs. 1940.00 5 HP 230/460 3 4.0 1800 210 lbs. 2144.00 5 HP 230 1 4.0 1800 215 lbs. 2336.00 5 HP Single Pump Unit on S.S. stand......................... 4023.00 5 HP Dual Pump Unit on S.S. stand............................ 6322.00

DAVENPORT, IA (800)

Volts

553-6975

Phase

GPM

PSI

www.dultmeier.com

Wt.

Net Ea.

E0003


Pumping Systems

15

Medium & High Pressure Pumping Units Pumping Units for Industrial Cleaning, Rinse Arches, Tire Applicators, Wax Arches, Presoak Arches or Multiple Gun Cleaning Stations. Features: Plunger Pumps belt driven by Baldor Motors. All systems include: • Pump • Motor • Pressure Regulator Valve • V-Belts • Pulleys • Belt Tightener • Pulsation Dampener (Not on all units) • Pressure Gauge • Stainless steel belt Guard • Stainless steel heavy gauge Baseplate • Pre-plumbed • All motors are 208/230/460 Volt, 3 phase. (1 phase available on special quote.) Note: Motor starters and electrical panels are available as an option if required.

D

Medium Pressure Models Part No. Pump GPM

Model PM820-TS

Baldor Motor

5 5 7-1/2 7-1/2 7-1/2 7-1/2 10 15 20

Net Ea.

175 $ 2414.00 175 2091.00 225 3182.00 225 2564.00 225 4665.00 225 3315.00 280 4550.00 400 6515.00 625 8799.00

High Pressure Models (No Pulsation Dampeners) Part No. Pump GPM

DU PM540 DU PM550 DU PM570 DU PM70 DU PM75 DU PM80 DU PM650 DU PM580 DU PM590 DU PM680 DU PM1050-15 DU PM660 DU PM690 DU PM720

D

Model PM2520 Shown

PSI Motor HP Wt./Lbs.

DU PM390 Cat 12 600 DU PM623 Cat 6 1200 DU PM820 Cat 10 1000 DU PM900 Arimitsu 10 1000 DU PM820-TS * Cat 10 1000 DU PM1010 Cat 13 700 DU PM1520 Cat 15 1000 DU PM2520 Cat 25 800 DU PM3535 Cat 30 1000 * Standard with Poly Tank / S.S. Frame.

— Pump Stands & Tanks also available —

AR CAT CAT CAT AR AR CAT AR AR AR CAT CAT AR AR

PSI Motor HP Wt./Lbs.

4.0 4000 4.5 3000 4.5 4000 4.5 5000 5.5 4000 5.5 5100 7.0 3000 7.0 3200 7.0 4000 8.0 3500 10 2000 10 2900 11 3000 13 2200

15 10 15 15 15 20 15 15 20 20 15 20 25 20

Net Ea.

350 $ 2786.00 290 2403.00 350 4082.00 390 4938.00 350 3167.00 390 3497.00 350 4558.00 350 2887.00 390 3422.00 390 3248.00 350 4172.00 390 5034.00 450 3959.00 390 3581.00

Wanner Pump Units High volume, high pressure pumping units featuring Wanner Hydra-Cell Diaphragm Pumps. Ideal for prep units, presoak arches and the rigors of “reclaim water”. PMD10

Standard Features: • Hydra-Cell Pump • TEFC 3-phase Motor • Heavy-gauge Stainless Baseplate • Pressure Bypass Valve • Pulleys and V-Belts • Stainless Belt Guard • Belt Tightener • Pressure Gauge • Pre-plumbed • All motors are 208/230/460 Volt, 3 phase. (Single phase motors available on special request.)

D

Part No.

We custom build Pumping Units to 60 GPM Flow Rates and 5000 PSI Pressure Ranges. Call Us for a Quotation OMAHA, NE (800)

228-9666

Featuring Hydra-Cell Diaphragm Pumps

Max Flow

Max. Pressure

HP

Wt./Lbs.

Net Ea.

DU PMD10 8 GPM 1000 PSI 7-1/2 245 $ 2728.00 DU PMD15 13 GPM 1500 PSI 15 575 6726.00 DU PMD25 20 GPM 1000 PSI 15 575 5866.00 DU PMD40 * 36 GPM 800 PSI 20 900 9075.00 DU PMD10-TS D10 Pump Unit with Tank & SS Stand......... 4484.00 DU PMD15-TS D15 Pump Unit with Tank & SS Stand......... 7828.00 DU PMD25-TS H25 Pump Unit with Tank & SS Stand......... 7142.00 DU PMD40-TS * H35 Pump Unit with Tank & Painted Stand 10205.00 * Rated to 1000 PSI with 25 HP Motor.

PMD10-TS Pump System

DULTMEIER SALES

D

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0002


HydroStatic Test Units • Water Jetters

16

Water Jetter Sewer Units Electric Drive Drain Clean Jetters with Electric Motor Drive on hand carry frames. Designed to create a pulsing flow to dislodge clogged drains and plumbing lines. Easy-to-use and transport. All units include handy carry frames, 120 Volt motors, GFI power cord, adjustable pressure regulator and plunger pump. (Jetter hoses and nozzles are not included as many options exist. See hose and nozzle sections). D

Part No.

DU JT50 DU JT50C DU JT86 DU JT86C DU JT100 DU JT100C

GPM

PSI

2.1 2.1 2.1 2.1 3.0 3.0

1000 1000 1500 1500 1000 1000

Motor

Pump

Wt.

1.5 HP, 13.5 Amp General 1.5 HP, 13.5 Amp Cat Pumps 2 HP, 20 Amp General 2 HP, 20 Amp Cat Pumps 2 HP, 20 Amp General 2 HP, 20 Amp Cat Pumps

Net Ea.

$ 1065.00 1318.00 1096.00 1399.00 1096.00 1451.00

65 lbs. 65 lbs. 75 lbs. 75 lbs. 75 lbs. 75 lbs.

Model JT50 1-1/2 HP Electric

Jetter Valve

Water Jetter Sewer Units Gas Drive Drain Clean Jetters with Gas Engine Drive on hand carry or portable carts. Designed to create a pulsing flow to dislodge clogged drains and plumbing lines. Easy-to-use and transport. All units include portable frames, gas engine, plunger pump and adjustable pressure regulator. Both units are mounted to an aircraft aluminum frame with pneumatic wheels and hose reel with a capacity of 150’ of 3/8” hose. (Jetter hoses and nozzles are not included as many options exist. See hose and nozzle sections).

D

Part No.

BI JD3027 BI JD4040 Model JD4040 13 HP Gas Drive

GPM

PSI

3.0 4.0

2700 4000

Motor

Pump

Wt.

6.5 HP Honda General 170 lbs. 13 HP Honda General 225 lbs.

Net Ea.

$ 1175.00 1525.00

Jetter Valve

Hydrostatic Test Units Designed to test the integrity of pipes and plumbing system required by local codes. Ideal for use with sprinkler systems or sewer lines. All units feature hand carry carts except Model 1050U which is on a aircraft aluminum frame with pneumatic wheels. Gas engine or electric drive as shown.

Model PM20HS 3/4 HP Electric

D

D

Model 1050HU 5 HP Gas

Model 80410 3/4 HP Electric

D

Part No.

PX 80410 DU PM20HS DU PM35HS BI 1050HU DULTMEIER SALES

OMAHA, NE (800)

228-9666

GPM

PSI

Motor

Pump

Wt.

3.1 400 120V, 3/4 HP Motor PumpTec 38 lbs. 2.1 500 120V, 3/4 HP Motor General 65 lbs. 2.8 1000 120V, 2 HP Motor General 80 lbs. 10 500 5 HP Honda Engine Udor 165 lbs.

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

Net Ea.

$ 795.00 833.00 991.00 1698.00 E0787


Gas Engine Pressure Wash Units

17

• Pressures from 2000 to 5000 PSI

• Honda Engines

• Cat Pumps®, AR or General Pumps

Standard Features include the following: Triplex Plunger Pumps • Adjustable pressure regulator valves • Trigger style shut-off guns • Chemical injection systems (except on 5000 psi units) • 30' or 50' x 3/8" high pressure hose assemblies • Insulated spray wands • High pressure gun swivels • Thermal relief valves on some units • Heavy duty aluminum, stainless or painted baseplates, depending on the model • High quality brass or stainless fittings • Pre-plumbed and tested prior to shipment. Engines are rope pull start except for GX630 and GX690 which feature 12 volt starters. PM6000G Belt Drive (Aluminum Cart) 4 GPM @ 3500 PSI

D

D

50 ft. Hose PM7500G Belt Drive (Powder-Coated Steel 4 Wheel Cart) 5 GPM @ 5000 PSI 50 ft. Hose

Belt Drive Pump Design slows pump speed down for longer life of pumps and components. Direct Drive Pump Design is a more economical way to assemble high pressure pumps to the engines. Eliminates the need for gear boxes or gear reduction engines. However, the pump is running at direct engine speed. Gear Box Pump Design incorporates a gear box between the engine and the pump. Lowers the engine speed to the pump allowing it to run at a much slower RPM thus extending pump life. We recommend gear box or belt drive design units over direct drive for customers that will use their pump units on a daily basis such as contract cleaners or industrial users. PM3000G-WH Gear Box Drive (Aluminum Cart) 4 GPM @ 3500 PSI

PMC-SF35C Direct Drive (Aluminum Cart) 2.5 GPM @ 2700 PSI

D

50 ft. Hose

D

D

30 ft. Hose

Max. Max. HONDA Part No. Flow PSI Engine Pump Hose BI PMC-SF35C 2.5 2700 GC190 AR 25' BI PMC-SF35H 2.5 2700 GC190 Cat 25' BI PMC-800H 3.0 2500 GC190 AR 25' BI PMC-950H 3.0 3200 GX270 AR 50' DU PM3000G-WH 4.0 3500 GX390 Cat 50' DU PM6000G 4.0 3500 GX390 Cat 50' DU PM5500G 4.0 4000 GX390 Cat 50' DU PM4500GC 4.0 4000 GX390 Comet 50’ DU PM8000G 4.0 4000 GX390 General 50’ DU PM7500G * 5.3 4000 GX630 Comet 50' DU PM8500G * 4.5 5000 GX630 General 50’ DU PM7000G * 5.5 5000 GX690 General 50' * Electric Start is Standard.

DULTMEIER SALES

OMAHA, NE (800)

Drive Style Direct Drive Direct Drive Direct Drive Direct Drive Gear Box Belt Drive Direct Drive Direct Drive Belt Drive Belt Drive Belt Drive Belt Drive

228-9666

Wt 95 lbs. 100 lbs. 105 lbs. 115 lbs. 175 lbs. 200 lbs. 170 lbs. 175 lbs. 185 lbs. 275 lbs. 265 lbs. 290 lbs.

PM8500G Belt Drive (Aluminum 2 Wheel Cart) 4.5 GPM @ 5000 PSI

Net Ea. $ 491.50 689.00 659.00 997.00 1779.00 1595.00 1150.00 1035.00 1525.00 3248.00 3698.00 3950.00

DAVENPORT, IA (800)

553-6975

D

www.dultmeier.com

E0005


Pressure Washers

18

Hydraulic Pressure Washers

12-Volt Pressure Washer Portable Hand Carry

12-Volt Portable Pressure Washer on Hand Carry Cart. Continuous duty, sealed motor. On-off switch with circuit breaker. Unloader valve, 25’ high pressure hose, quick connect fittings, spray gun and chemical injector. 15’ Battery cables with heavy duty clamps are also included.

These hydraulically-driven pressure washers are designed for remote and explosion-proof environments where electricity cannot be used. The ideal choice for use with washdown and cleaning of construction equipment, agricultural equipment, concrete cleanup, etc.

D

D

D

Part No.

GPM

PX 80391

1.5

PSI Amp Draw Wt. Net Ea.

500

65

Wand & Hose are included in some kits

60 lbs. $ 1269.00

12-Volt Pressure Washer Kits Compact 12-Volt Pressure Washer Kits are simple, fast, quiet and reliable. Sealed motors with push/pull switch and circuit breaker. All kits include unloader valve, spray wand, 25’ spray hose, suction filter and inlet hose, chemical injector and motor mounts. Can be easily mounted to your equipment frame.

Kits are complete with hydraulic motor, HYPRO plunger pump, mounting rails, unloader valve, pressure gauge and quick disconnect for hose. Some models come with spray wand and 50’ hose as shown. A wide variety of flows and pressures are available to meet your needs. Ports are 1/2” FPT x 3/4” FGHT inlet and 3/8” male quick disconnect. Rated to 160° F. Part No. Cleaning Capacity

HY 1803C 3.0 GPM @ 1000 PSI 5 GPM @ 1000 PSI HY 1805C 3.0 GPM @ 1500 PSI 8 GPM @ 1900 PSI HY 1807C 3.0 GPM @ 2000 PSI 11 GPM @ 1300 PSI HY 1827C 4.0 GPM @ 2000 PSI 8 GPM @ 2000 PSI Note: These models do not include hose & wand assembly.

D D

Part No. Cleaning Capacity

PWK71

Part No.

1.0 1.5 * 1.5

200 500 500

15 65 65

* No Switch or 25’ of Hose - For Direct Wiring.

20 lbs. 55 lbs. 50 lbs.

Hydraulic Motor Requirements

Wt.

Net Ea.

28 lbs. $ 1035.00 28 lbs. 1094.00 28 lbs. 1209.00 33 lbs. 1249.00

Wt.

Net Ea.

HY 1802 3.0 GPM @ 1000 PSI 5 GPM @ 1300 PSI 38 lbs. $ 1213.00 HY 1804 3.0 GPM @ 1500 PSI 8 GPM @ 1900 PSI 41 lbs. 1271.00 HY 1806 3.0 GPM @ 2000 PSI 11 GPM @ 1300 PSI 41 lbs. 1388.00 HY 1826 4.0 GPM @ 2000 PSI 8 GPM @ 2000 PSI 49 lbs. 1427.00 Note: These models also include spray wand & 50’ hose assembly.

GPM PSI Amp Draw Wt. Net Ea.

PX PWK15 PX PWK71 PX 80729

Hydraulic Motor Requirements

$ 335.00 1098.00 634.00

Enclosed Cold Water Pressure Washers

Hydraulic Drive Plunger Pumps Hydraulic Plunger Pumps from UDOR. Widely used for pressure wash, truck wash, construction and industrial cleaning applications. Pumps feature brass manifolds with ceramic plungers. High efficiency gear motors with flex coupler drive. Mounting rails are included. Rated to 160° F. Must be pressurized or flooded suction. (Note: Unloader valves, gauges, wands and hoses are not included but can be ordered separately.)

Many industries require enclosed and covered pump systems for industrial cleaning applications. These cold water units are belt-driven and feature electric motors and General plunger pumps in a stationary, enclosed housing. All units include trigger wand, 50’ of hose, high pressure detergent system, float tank, unloader valve and external on-off switch. (Other motor phase is available from those shown).

50 ft. Hose D D D

MD4030SH

Hydraulic Driven Part No. UD PND3020ZH UD MD4030SH UD MKD4040SH UD GKC3817SH UD GKC3820SH

Pump/Motor Units Max. Max. Hydraulic Flow PSI Requirements 3.0 1500 5 GPM @ 1800 PSI 4.0 3000 12 GPM @ 1500 PSI 4.0 4000 12 GPM @ 2000 PSI 10.0 2000 15 GPM @ 2000 PSI 10.0 2500 15 GPM @ 2400 PSI

DULTMEIER SALES

Wt. 24 lbs. 36 lbs. 39 lbs. 65 lbs. 70 lbs.

OMAHA, NE (800)

Net Ea. $ 808.00 1035.00 1114.00 1802.00 1802.00

228-9666

Part No. WD WD311 WD WD418 WD WD518 WD WD430 WD WD530

DAVENPORT, IA (800)

Wand

Max. Max. Flow PSI Motor Wt. 3.0 GPM 1100 2 HP / 1 PH / 115V 230 lbs. 4.0 GPM 1800 5 HP / 1 PH / 230V 330 lbs. 4.8 GPM 1800 6 HP / 1 PH / 230V 335 lbs. 4.0 GPM 3000 8 HP / 1 PH / 230V 390 lbs. 5.0 GPM 3000 10 HP / 3 PH / 230V 350 lbs.

553-6975

www.dultmeier.com

D

Net Ea. $ 1345.00 1745.00 2015.00 2125.00 2981.00

E0907


19

Portable Hot Water Pressure Washers

Hot Water Pressure Washers for tough industrial cleaning. Professionally engineered to combine Hot Water, Pressure and Volume to provide efficient and effective cleaning. Available in oil-fired portable units or Natural gas & LP gas stationary units. Designed to provide water temperatures to 180° F. All units feature General Plunger Pumps. (All units are American Made)

Oil Fired - Electric Motor Driven Portable Oil-Fired Wash Units feature automatic burner ignition.Two pipe “no purge” oil pump assures trouble-free operation using diesel or kerosene fuel. All systems are standard with chemical metering feature and adjustable thermostat. Fuel tank capacity is 7.5 Gallons. Motors are 1–phase. All units are factory fired and tested and ready for immediate use. (3-phase motors available on request). Standard Features Include: Trigger gun & 50' hose with quick couplers • Downstream chemical injection system • Unloader valve • Safety relief Pop-off • Hi-Limit temperature control • 1/2" Schedule 80 coil • Flow switch for burner shutdown • Pneumatic wheels • Pressure atomizing burner • Hose & Gun Hanger • 5 Year prorated coils.

We Can Supply Most Any Replacement Coils - Call for Pricing!

Part No.

Description Net Ea.

DU DP2-1400 DU DP3-1000 DU DP3-2000 DU DP3-2800 DU DP4-3000

Rated at 2.0 GPM @ 1400 PSI. Dimensions: 30" W x 38" L x 40" H. Motor: 2 HP, 115 Volt, 1-phase. Wt. 340 lbs....................................... $ 2065.00 Rated at 3.0 GPM @ 1000 PSI. Dimensions: 30" W x 38" L x 40" H. Motor: 2 HP, 115 Volt, 1-phase. Wt. 340 lbs....................................... 2135.00 Rated at 3.0 GPM @ 2000 PSI. Dimensions: 30" W x 38" L x 40" H. Motor: 4 HP, 230 Volt, 1-phase. Wt. 380 lbs....................................... 2195.00 Rated at 3.0 GPM @ 2800 PSI. Dimensions: 30" W x 38" L x 40" H. Motor: 6 HP, 230 Volt, 1-phase. Wt. 475 lbs....................................... 3149.00 Rated at 4.0 GPM @ 3000 PSI. Dimensions: 30" W x 38" L x 40" H. Motor: 8 HP, 230 Volt, 1-phase. Wt. 475 lbs....................................... 3275.00

D

Oil Fired - Gas Engine Driven Portable Oil-fired Wash Units have the same standard features as the electric motor driven units above but with the added benefit of being able to use them when electrical power may not be available. Available from 6.5 HP to 13 HP gas engines. Burner motors are 12 volt. 6.5 HP is rope pull, 9 HP through 13 HP units are standard with electric start (Batteries not included). 5 Year prorated coils.

D

Part No.

Description Net Ea.

DU DG3-3000

Rated to 3.0 GPM @ 3000 PSI. Dimensions: 32” W x 48” L x 40” H. Engine: 9 HP Honda. Wt. 560 lbs............................................................

3998.00

DU DG4-3000

Rated to 4.0 GPM @ 3000 PSI. Dimensions: 32” W x 48” L x 40” H. Engine: 11 HP Honda. Wt. 575 lbs..........................................................

4398.00

DU DG3-4000

Rated to 3.5 GPM @ 4000 PSI. Dimensions: 32” W x 48” L x 40” H. Engine: 13 HP Honda. Wt. 575 lbs.......................................................... 4182.00

DU DG3-2500

Rated to 3.0 GPM @ 2500 PSI. Dimensions: 32” W x 48” L x 40” H. Engine: 6-1/2 HP Briggs. Wt. 530 lbs...................................................... $ 2995.00

dultmeier.com

• Shop and Order On-Line 24 Hours a Day, 7 Days a Week! • Large Inventories of Over 3 Million Total Items! • View Current Pricing! • Web Specials and Bargain Corner! • Know Your Part Numbers? Use the Web Quick Order Page! • Hundreds of Parts List Schematics (and more to come!) • Technical Library packed with information! • See New Items Not Shown in Our Printed Catalogs! • Track Your Order Status and History! • Secure Site for Safe On-Line Ordering. DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0006


Stationary Washers & Cleaners

20

Stationary Hot Waters Pressure Washers – Cabinet Style – Stationary Natural Gas or LP Fired Pressure Washers are engineered to provide maximum cleaning efficiency. Strong enough to tackle the most demanding cleaning jobs. Designed to provide water temperatures to 180° F. All units feature chemical solution system for injecting cleaning chemicals into the pumping line. All units feature General Plunger Pumps driven by electric motors.

Standard Features Include: Trigger spray gun with wand • 50’ high pressure hose with quick couplers • Unloader valve • Safety pop-off valve • Flow switch for burner shutdown • Schedule 80 1/2” Coil • Adjustable Thermostat • Upstream high pressure chemical injection system • Low water shut-off • Draft diverters available on request. Note: All units are fired and tested. (Please specify LP or Natural Gas). 5 Year prorated coils.

D

50 ft. Hose Part No.

DU DS3-2400 DU DS4-3000 DU DS5-3000 DU DS7-3000 DU DS10-2000 DU DS10-3000

Flow

PSI

* 3 GPM * 4 GPM 5 GPM 7 GPM 10 GPM 10 GPM

2400 3000 3000 3000 2000 3000

HP

5 HP / 1 PH 8 HP / 1 PH 10 HP / 3 PH 15 HP / 3 PH 15 HP / 3 PH 20 HP / 3 PH

Wt.

Net Ea.

725 lbs. $ 3548.00 800 lbs. 4429.00 860 lbs. 5098.00 1390 lbs. 6975.00 1640 lbs. 7798.00 1660 lbs. 8095.00

Provides Maximum Cleaning Efficiency!

* 3 Phase Motors are Available on these Models.

Stationary Steam Cleaners – Natural Gas or LP Fired – For tough cleaning applications where high temperature steam is required in place of standard hot water machines. Open gun, steam units are rated to 210° F. Belt-driven, General plunger pumps are driven by 2 hp / 1 phase motors. Can be run on Natural or LP Gas, please specify at time of order. Standard Features Include: General plunger pumps • 2.3 hp / 1 phase / 115 volt motors • 3/8” x 50’ steam hose with open flow spray wand • 210° F. output temperature • 10” diameter flue size • Tested and fired before shipped • 5-Year prorated warranty • Draft diverters available on request. (Oil-fired units and UL or CSA Certified options are available on request).

Part No.

DU W3030S DU W4530S

Call Us For All Your Pressure Washer Needs! OMAHA, NEBRASKA

DAVENPORT, IOWA

1-800-228-9666

1-800-553-6975

FAX: 1-402-333-5546

FAX: 1-563-386-5448

OMAHA, NE (800)

228-9666

PSI

Wt.

300 300

725 lbs. 880 lbs.

Net Ea.

$ 3750.00 5150.00

SERVICE & REPAIRS

Did you know? We can service almost every brand of pump that we sell in our catalog.

Call us at 1-800-228-9666 (Omaha, NE) for a quote!

http://www.dultmeier.com

DULTMEIER SALES

Flow

3.0 GPM 4.2 GPM

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0961


High Pressure Trailer Units

21

High Pressure Trailer Units High Pressure Trailer Units for Mobile Cleaning Applications. Complete and ready-to-go. All units are self-contained and do not require outside power source. 200 Gallon Water Tank

COLD WATER

100 ft. of Low Pressure Hose & Reel

General Plunger Pump

TR5540/TR5550/TR8035

Heavy Duty Commercial Trailer Package TR Cold Water Units Feature: General Pump • Honda Engine with electric start • 12 Volt battery • Powder-coated steel trailer • Trailer lights, jack, safety chains, tool box, aluminum fenders & 15” tires • 15 Gallon remote gas tank • 25 Gallon chemical tank installed on trailer • High pressure manual hose reel with 150’ of hose • Low pressure manual hose reel with 100’ of hose • Pre assembled and tested prior to shipping • Dimensions are 136” L x 82” W x 63” H.

150 ft. of High Pressure Hose & Reel

Honda Engine

Hitch with Jack D

Note: Jetter valves, nozzles and sewer hose are available for sewer cleaning applications if required.

15” Tires with Grease Bearings

15 Gallon Engine Fuel Tank

Lights 100 ft. of Low Pressure Hose & Reel

150 ft. of High Pressure Hose & Reel

HOT WATER TS4040

Vertical Burner Hot Shot Trailer Package TS4040 Hot Water Units Feature: General Pump • Honda Engine with electric start • 12 Volt battery • Powder-coated steel trailer • Trailer lights, jack,safety chains, tool box, aluminum fenders & 15” tires • Fuel tank attached to engine • 25 Gallon chemical tank installed on trailer • 8 Gallon burner fuel tank • High pressure manual hose reel with 150’ of hose • Low pressure manual hose reel with 100’ of hose • Pre assembled and tested prior to shipping • Dimensions are 136” L x 82” W x 63” H.

200 Gallon Water Tank

Standard Fuel Tank on Engine

Vertical Burner

8 Gallon Burner Fuel Tank

Hitch with Jack

Honda Engine

D

15” Tires with Grease Bearings

Lights Horizontal Burner 150 ft. of High Pressure Hose & Reel

200 Gallon Water Tank

100 ft. of Low Pressure Hose & Reel

HOT WATER TH4040/TH5535/TH5540/TH8035

Pro-Super Skid Trailer Package Honda Engine

15 Gallon Engine Fuel Tank

D

TH Hot Water Units Feature: General Pump • Honda Engine with electric start • 12 Volt battery • Powder-coated trailer • Trailer lights, jack, safety chains, tool box, aluminum fenders & 15” tires • 15 Gallon remote fuel tank (except on TH4040 which has tank or engine) • 15 Gallon burner fuel tank • 25 Gallon chemical tank is supplied but is not installed on the trailer • High pressure manual hose reel with 150’ of hose • Low pressure manual hose reel with 100’ of hose • Pre assembled and tested prior to shipping • Dimensions are 136” L x 82” W x 63” H.

Hitch with Jack

COLD WATER UNITS Part No. Lights

15 Gallon Burner Fuel Tank

15” Tires with Grease Bearings

BI TR5540 BI TR5550 BI TR8035

Rated Output

5.5 GPM @ 4000 PSI 5.5 GPM @ 5000 PSI 8.0 GPM @ 3500 PSI

HOT WATER UNITS Part No.

Rated Output

Engine

Wt.

Honda GX630 Honda GX690 Honda GX690

1425 lbs. 1450 lbs. 1450 lbs.

Engine

BI TS4040 * 4.0 GPM @ 4000 PSI Honda GX390 BI TH4040 4.0 GPM @ 4000 PSI Honda GX390 BI TH5535 5.5 GPM @ 3500 PSI Honda GX630 BI TH5540 5.5 GPM @ 4000 PSI Honda GX630 BI TH8035 8.0 GPM @ 3500 PSI Honda GX690 * Vertical Burner Flue. Built-in gas tank attached to engine. DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

Wt.

1475 lbs. 1475 lbs. 1495 lbs. 1495 lbs. 1495 lbs.

www.dultmeier.com

Net Ea.

$ 8350.00 9319.00 8975.00 Net Ea.

$ 7925.00 8695.00 9695.00 9990.00 10250.00

E0785


Skid Mounted Sprayer • Jetter Units

22

Skid Mount High Pressure Units For Pickups and Flatbeds Skid Mounted Pressure Washers are “Self-contained” wash units that are perfect for a wide variety of cleaning requirements. Easy in-out design for pickup or flat bed trailers. All units feature GX Series Honda engines and General plunger pumps. Frames are aircraft grade aluminum that are chemical-resistant and rustproof. Standard Features: Includes 200 gallon water tank • Hand rewind reel with 100’ of hose • Trigger wand with extension • Chemical injector • Direct drive or belt driven pump as noted • Dimensions are 49” W x 62” L x 44” H. D

Part No.

Flow

Pressure Drive Wt./Lbs.

BI PS3027D 3.0 GPM 2700 PSI Direct BI PS4040D 4.0 GPM 4000 PSI Direct BI PS4040BT 4.0 GPM 4000 PSI Belt

375 400 400

Net Ea.

$ 2075.00 2365.00 2795.00

PS4040D

Skid Mount High Pressure Unit For ATV Vehicles Skid Mounted Pressure Washer is designed for ATV vehicles like Gator, Rhino, Mule and many others. Totally self-contained wash unit that is perfect for a variety of cleaning applications. Skid is constructed of aircraft grade aluminum that will not rust and are chemical-resistant. Designed for easy in-out when not needed. D

Standard Features: 50 gallon water tank • Hand rewind reel with 100’ of hose • Trigger wand with extension • Chemical injector • Direct drive pump • Honda GX Series engine • General Plunger Pump • Dimensions are 38” W x 48” L x 44” H. Part No.

PAT3027 Gator ATV NOT INCLUDED

Pressure

Drive

Wt./Lbs.

BI PAT3027 3.0 GPM 2700 PSI

Flow

Direct

???

Net Ea.

$ 2075.00

Pro-Tow Jetter Units Sewer / Jetter Trailer Units. All models include the following features: Electric start engine • Electric rewind hose reel • 200 Gallon water tank with float valve • General brand plunger pump with pulse valve • Foot activated control valve • Jetter nozzle pack • 25 Gallon winterizing tank • Marine battery • 15 Gallon fuel tank. Trailers are rated to 3500 lbs. capacity and include powder-coated frame, 15” tires, aluminum fenders, lights, jack, safety chains, poly tool box and external grease fittings. Complete jetter dimensions are 135” L x 82” W x 60” H.

D

All units are fully assembled and tested prior to shipping. Hose reel capacity is 500’ of 3/8” or 350’ of 1/2” hose. Hoses are not included but can be ordered to meet your specific needs. Part No.

Max. Flow

Max. PSI

BI 535JTR BI 835JTR BI 1030JTR BI 1230JTR

5.5 GPM * 8.0 GPM * 10 GPM * 12 GPM

3500 PSI 3500 PSI 3000 PSI 2800 PSI

Engine

Wt./Lbs.

Net Ea.

GX630 Honda 1485 $ 8545.00 GX690 Honda 1495 8945.00 27 HP Kohler 1495 10195.00 30 HP Kohler 1500 10495.00

* 8 GPM Unit can use 3/8” hose, but 1/2” is recommended due to pressure loss. 10 & 12 GPM Units require 1/2” hose. DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0007


Constant-Flo Gas Water Heaters

23

(Fan Assisted Design) Instantaneous, Continuous Flow Water Heaters. As much as 30-40% more efficient than tank-type water heaters. Available for Natural or LP Gas. FEATURES: Fully modulating design changes burner flame as flow rates change • Compact, space saving dimensions • Self-diagnostic programming • Digital remote control for temperature settings • Approved for use in circulating water systems • 120 Volt 60 Hz electric blower • Optional controllers for mounting from 2-20 heaters into one system • Low NOx compliant • Freeze protection to -30˚F • Carbon Monoxide monitoring system • Gas Shut-off valve is included • Maximum inlet pressure is 150 PSI.

TECHNICAL SPECIFICATIONS PH20R PH25C PH28R PH28C PH32C BTU/hr Min. 21,600 11,000 11,000 11,000 11,000 Gas input Max. 145,000 180,000 199,900 199,900 199,900 Net weight in lbs. 35 50 50 50 60 Hot water output: g/m 40˚F rise 5.3 7.4 8.5 8.5 8.9 100˚F rise 2.3 2.9 3.3 3.3 3.8 DIMENSIONS: Height 20-1/2” 25-5/8” 25-3/8” 25-3/8” 27-1/2” Width 13-3/4” 13-7/8” 14-7/8” 14-7/8” 18-1/2” Depth 5-1/8” 9-7/8” 9-7/8” 9-7/8” 9-3/4” *Vent size in. 3” 3”/5” 3”/5” 3”/5” 3” PVC Gas connection in. 3/4” 3/4” 3/4" 3/4” 3/4” Water connection in. 3/4” 3/4” 3/4" 3/4” 3/4” * Category III Venting Required. All Models available for Nat or LP Gas

Residential Models (Rated to 140° F.) PH20R: Rated to 5.3 GPM at 40 degree rise. Maximum temperatures to 140° F. BTU rating is 21,600 to 145,000 (141,000 LP). Designed for indoor direct vent. (3” Category III vent required) or outdoor where no venting is required. Up to 6 units can be combined to increase flow rate. Efficiency rating is 82%. PH28R: Rated to 8.5 GPM at 40 degree rise. Maximum temperatures to 140° F. BTU rating is 19,000 to 199,900. Designed for indoor direct vent, (4” Category III vent required) or outdoor where no venting is required. Up to 20 units can be combined to increase flow rate. Efficiency rating is 84%. Indoor Residential Part No. Type Gas PI PH20R-DVSN Direct Vent Natural PI PH20R-DVSP Direct Vent LP PI PH25R-DVSN Indoor Natural PI PH28RDVSN Direct Vent Natural PI PH28RDVSP Direct Vent LP

D

Direct Vent Nat: PH20R-DVSN LP: PH20R-DVSP

Outdoor Residential Part No. Type PI PH20R-OFN Outdoor PI PH20R-OFP Outdoor PI PH28ROFN Outdoor PI PH28ROFP Outdoor 

Gas Natural LP Natural LP

Flow Rate 5.3 GPM 5.3 GPM 7.4 GPM 8.5 GPM 8.5 GPM

Wt. Net Ea. 35 lbs. $ 683.00 35 lbs. 765.00 50 lbs. 857.00 55 lbs. 1019.00 55 lbs. 800.00

Flow Rate 5.3 GPM 5.3 GPM 8.5 GPM 8.5 GPM

Wt. Net Ea. 55 lbs. $ 679.00 55 lbs. 749.00 55 lbs. 966.00 55 lbs. 877.00

Commercial Models (Rated to 185° F.) PH25C: Rated to 7.4 GPM at 40 degree rise. Maximum temperatures to 185° F. BTU rating is 11,000 to 180,000. Designed for indoor direct vent, (3/5” Concentric Category III venting required) or outdoor where no venting is required. Up to 6 units can be combined to increase flow rate. Efficiency rating is 84%. PH28C: Rated to 8.5 GPM at 40 degree rise. Maximum temperatures to 185° F. BTU rating is 19,000 to 199,900. Designed for indoor direct vent, (4” Category III vent required) or outdoor where no venting is required. Up to 20 units can be combined to increase flow rate. Efficiency rating is 84%. **PH32C: Rated to 8.9 GPM at 40 degree rise. Maximum temperatures to 185° F. BTU rating is 11,000 to 199,900. This model is a condensing style that can be used indoor or outdoor and can be vented with 3” PVC pipe. Up to 20 units can be combined to increase flow rate. Efficiency rating is 93%.

D

Direct Vent PH28C

Indoor Commercial Part No. Type PI PH25C-DVSN Direct Vent PI PH25C-DVSP Direct Vent PI PH28C-DVSN Direct Vent PI PH28C-DVSP Direct Vent PI PH32C-DVN **Direct Vent PI PH32C-DVP **Direct Vent Outdoor Commercial Part No. Type PI PH25C-OFN Outdoor PI PH25C-OFP Outdoor PI PH28C0F-N Outdoor PI PH28C0F-L Outdoor PI PH32C-OFN **Outdoor PI PH32C-OFP **Outdoor 

DULTMEIER SALES

OMAHA, NE (800)

228-9666

Gas Natural LP Natural LP Natural LP

Flow Rate 7.4 GPM 7.4 GPM 8.5 GPM 8.5 GPM 8.9 GPM 8.9 GPM

Wt. Net Ea. 50 lbs. $ 876.00 50 lbs. 876.00 55 lbs. 1055.00 55 lbs. 977.00 60 lbs. 1389.00 60 lbs. 1389.00

Gas Natural LP Natural LP Natural LP

Flow Rate 7.4 GPM 7.4 GPM 8.5 GPM 8.5 GPM 8.9 GPM 8.9 GPM

Wt. Net Ea. 50 lbs. $ 827.00 50 lbs. 875.00 55 lbs. 897.00 55 lbs. 897.00 60 lbs. 1260.00 60 lbs. 1259.00

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

Venting Also Available! E0749


Water Heaters

24

Eco-Friendly, Energy Efficient, Endless Hot Water! Tankless, Instantaneous,Water Heaters. Eco-Friendly, Energy Efficient, Endless hot water. Savings from 20 to 50% over conventional water heaters. Takagi is the first and only company to receive (4) Energy Conservation Awards three years in a row in Japan. All units feature electronic ignition. Lightweight and easy-to-install. A variety of models for residential, light commercial and heavy-duty commercial applications. Adjustable output temperatures that vary from 4 to 16 settings depending on the model. Designed for Natural or LP Gas as noted. Requires 4” Category III venting on all models except TH2/TH2S and TM50.

Residential & *Light Commercial Duty Models TKJR: Rated to 6.6 gpm and temperatures to 185° F. BTU rating is 140,000. Designed for indoor applications but outdoor models are also available. Dimensions are 20.5” H x 13.8” W x 6.7” D. TK3: Rated to 7.0 gpm and temperatures to 185° F. BTU rating is 199,000. Designed for indoor, outdoor or direct vent applications. Dimensions are 20.5” H x 13.8” W x 8.5” D. TK4: Rated to 8.0 gpm and temperatures to 185° F. BTU rating is 190,000. Designed for indoor applications but direct vent kits and outdoor models are also available. Dimensions are 20.5” H x 13.8” x 8.5” D. D

KPRT4 Rain Cap

TD2*: Rated to 10 gpm and temperatures to 185° F. BTU rating is 199,000. Designed for indoor applications but outdoor models are also available. *Can be used for light duty commercial as well as residential applications. Up to 4 units can be connected together for increased flow. Dimensions are 20.5” H x 13.8” W x 8.5” D.

KPSXXX Tube Roof

TH2 & TH2S: Condensing models are rated to 91% efficient. Maximum output temperatures to 185° F. TH2S is rated to 8.0 GPM and 180,000 BTU’s. TH2* is rated to 9.0 GPM and 199,000 BTU’s.

TK3 / TK4

KPAR4 Roof Flashing KPRJ4 Roof Jack

Indoor direct vent models shown but outdoor units are also available. TH2* can be used for light duty commercial as well as residential applications. Up to 4 units can be connected for increased flow rates. Both models can be vented with PVC, CPVC or ABS piping. Dimensions are 25.5” H x 18.5” W x 12.5” D.

KPSXXX Tube

VENTING 4” CAT III

Heavy-Duty Commercial Models TK3PRO: Rated to 7.0 gpm and temperatures to 185° F. BTU rating is 199,000. Can be used indoor, outdoor or direct vent. Can be linked with up to 4 units for increased flow. Dimensions are 20.5” H x 13.8” W x 8.5” D.

D

TM32

TM32: Rated to 9.0 gpm and temperatures to 185° F. BTU rating is 240,000. Can be used indoor or outdoor or direct vent. Up to 20 units can be linked for increased flow. Available in ASME version if required. Dimensions are 23.6” H x 18.5” W x 8.9” D. TM50: Rated to 14.5 gpm and temperatures to 185° F. BTU rating is 380,000. Can be used indoor, outdoor or direct vent. Up to 10 units can be linked for increased flow. Available in ASME version if required. Dimensions are 25.2” H x 24.8” x 11.8” D. (Note: 5” venting required).

KPSP4 Storm Collar

KPFR4 Flashing

KPSS44 Straps

KPE904 / KPE454 Elbow KPSXXX Tube

KPSXXX Tube

KPWH4 or KPWL4

Condensate drain needed for vent runs longer than 5 ft. (KPDRV4)

Sidewall Termination

Back flow for freeze prevention (TV03)

Maximum Max. Part No. Gas Type Flow Rate BTU’s

TA TKJR Natural 6.6 gpm TA TKJR-LP LP 6.6 gpm TA TH2S-DV Natural 8.0 gpm TA TH2S-DVL LP 8.0 gpm TA TK4-NG Natural 8.0 gpm TA TK4-LP LP 8.0 gpm TA TK3L LP 7.0 gpm TA TD2-NG Natural 10 gpm TA TD2-LP LP 10 gpm TA TH2-DV Natural 9.0 gpm TA TH2-DVL LP 9.0 gpm TA TM32 Natural 9.0 gpm TA TM32-L LP 9.0 gpm TA TM32AM ** Natural 9.0 gpm TA TM32AM-L ** LP 9.0 gpm TA TM50-N Natural 14.5 gpm TA TM50-L LP 14.5 gpm TA TM50-NA ** Natural 14.5 gpm TA TM50-LA ** LP 14.5 gpm ** ASME Rated. DULTMEIER SALES

140,000 140,000 180,000 180,000 190,000 190,000 199,000 199,000 199,000 199,000 199,000 240,000 240,000 240,000 240,000 380,000 380,000 380,000 380,000

Wt.

29 lbs. 29 lbs. 70 lbs. 70 lbs. 35 lbs. 35 lbs. 35 lbs. 35 lbs. 35 lbs. 73 lbs. 73 lbs. 51 lbs. 51 lbs. 51 lbs. 51 lbs. 112 lbs. 112 lbs. 112 lbs. 112 lbs.

Net Ea.

$ 715.00 699.00 1221.00 1221.00 929.00 929.00 739.00 1154.00 1154.00 1356.00 1356.00 1693.00 1693.00 2074.00 2074.00 3342.00 3367.00 3692.00 3692.00

FLOW CHART Temperature Rise @ Gallons Per Minute Temperature Rise TKJR TK3 TK4 TH2S TD2 TH2 TM32 TM50 35° F. 6.6 7.0 8.0 8.0 9.3 9.0 9.0 14.5 40° F. 5.7 7.0 7.8 8.0 8.1 9.0 9.0 14.5 45° F. 5.1 7.0 6.9 7.0 7.2 8.0 8.5 13.5 50° F. 4.6 6.5 6.2 6.5 6.5 7.0 7.7 12.1 55° F. 4.2 5.9 5.7 6.0 5.9 6.5 7.0 11.0 60° F. 3.8 5.4 5.2 5.4 5.4 6.0 6.4 10.1 65° F. 3.5 5.0 4.8 5.0 5.0 5.6 5.9 9.3 70° F. 3.3 4.7 4.4 4.8 4.7 5.1 5.5 8.7 80° F. 2.9 4.1 3.9 4.0 4.1 4.6 4.8 7.6 90° F. 2.5 3.6 3.5 3.7 3.6 4.0 4.1 6.7 95° F. 2.4 3.4 3.3 3.4 3.4 3.9 4.0 6.5 100° F. - - - 3.2 3.3 3.7 3.9 6.3

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0654


Commercial Gas-Fired

25

Water Heaters FREIGHT-FREE FROM FACTORY!!

• Low profile automatic flue damper for lower overall heights.

Conventional water heaters are always wider and usually taller than The Universal Replacements from Ruud.

• Dielectric nipples speed installation while providing the ultimate in tank corrosion protection.

Dimensional Information All dimensions shown in inches.

Clearances to Shipping "A" "B" Combustibles Wt.

**FREE

• Multiple inlet/outlet connections for more flexible hookups.

Model No. Height Width Vent Rear Sides Top (Lbs.) G50-98 62-3/4 22-1/2 5 2 2 12 270 G75-125 65-1/2 26-1/4 5 2 2 12 480 G82-156 68-13/16 26-1/4 6 2 2 12 490 G76-180 68-13/16 26-1/4 6 2 2 12 540 G37-200 49-1/4 26-1/4 6 2 2 12 450 G76-200** 68-13/16 26-1/4 6 2 2 12 540 G91-200** 76-5/16 26-1/4 6 2 2 12 600 G100-200** 73-1/16 30-1/4 6 4 2 12 780 G72-250 71-1/16 26-1/4 6 6 6 12 590 G100-250 73-1/4 30-1/4 6 4 2 12 795 G100-270 73-7/8 30-1/4 6 4 2 12 805 G72-300 71 26-1/4 8 6 6 12 590 G100-310 75 30-1/4 7 6 6 12 770 G65-360 70-11/16 26-1/4 8 6 6 12 640 G65-400 70-11/16 26-1/4 8 6 6 12 640 G85-400 72-5/16 26-1/4 10 6 6 12 640 G100-400 76 30-1/4 8 6 6 12 770

• Smaller jacket diameters for squeezing through tight spaces. • Hand-hole cleanout for faster sediment removal. • EXCLUSIVE System Sentinel diagnostics eliminate the guesswork in troubleshooting. • Full-flow brass drain valve reduces maintenance time.

** These (3) Units Ship F.O.B. Detroit, MI.

• Stainless steel burner slides right out for easier maintenance

D

** NOTE: ALL HEATERS ARE FREIGHT PRE-PAID!! Universal Specifications RECOVERY CAPACITIES (Specify Natural or LP Gas)

Recovery in U.S. Gallons/Hr. (GPH) at various temperature rises TEMPERATURE RISE - DEGREES F - GALLONS PER HOUR Model No. Capacity Input Efficiency 40˚F 50˚F 60˚F 70˚F 80˚F 90˚F 100˚F 110˚F 120˚F 130˚F 140˚F Net Ea. HU G50-98 50 98,000 80% 238 190 158 136 119 106 95 86 79 73 68 $ 3539.00 HU G75-125 * 75 125,000 80% 303 242 202 173 152 135 121 110 101 93 87 3670.00 HU G82-156 * 82 156,000 80% 378 303 252 216 189 168 151 138 126 116 108 4610.00 HU G76-180 76 180,000 80% 436 349 291 249 218 194 175 159 145 134 125 4727.00 HU G37-200 * 35 199,900 80% 485 388 323 277 242 215 194 176 162 149 138 4655.00 HU G76-200 * 76 199,900 80% 485 388 323 277 242 215 194 176 162 149 138 2945.00 HU G91-200 * 91 199,900 80% 485 388 323 277 242 215 194 176 162 149 138 2998.00 HU G100-200 * 100 199,900 80% 485 388 323 277 242 215 194 176 162 149 138 2898.00 HU G72-250 * 72 250,000 80% 606 485 404 346 303 269 242 220 202 186 173 5089.00 HU G100-250 * 100 250,000 80% 606 485 404 346 303 269 242 220 202 86 173 5425.00 HU G100-270 * 100 270,000 80% 655 524 436 374 327 291 262 238 218 201 187 5595.00 HU G72-300 72 300,000 80% 727 582 485 416 364 323 291 264 242 224 208 5670.00 HU G100-310 100 310,000 80% 752 601 501 429 376 334 301 273 251 231 215 5598.00 HU G65-360 * 65 360,000 80% 873 698 582 499 436 388 349 317 291 269 249 6460.00 HU G65-400 65 399,900 80% 969 776 646 554 485 431 388 353 323 298 277 7225.00 HU G85-400 85 399,900 80% 969 776 646 554 485 431 388 353 323 298 277 7798.00 HU G100-400 * 100 399,900 80% 969 776 646 554 485 431 388 353 323 298 277 7998.00

Recovery rating is based on a recovery efficiency obtained in a CSA-certified laboratory. Standard with Non-ASME tanks. ASME tanks available, call for pricing. NOTE: Specify Natural or LP Gas. * Low NOx Model Available. DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0673


Commercial Electric

Water Heaters

Heavyweight Electric

26

FREIGHT-FREE FROM FACTORY!!

Heavyweight electrics provide versatile performance. General-use water FREE Cap. 100˚F Wt. Shipping heaters are ideal for applications requiring large quantities of hot water. Suitable for general hot water applications. Surface mounted thermostats. ASME products also available at additional charge. • System SentinelTM Diagnostic System - a Rheem exclusive! LED lights monitor the on-off function of each heating element. Pinpoints the nonfunctioning element, saving service time and cost. • Corrosion-resistant tank, featuring exclusive steel formulation with high-temperature porcelain enamel coating - built to last for years. • LifeguardTM Stainless Steel Element - Covered by a three-year warranty, Lifeguard's low-watt density design minimizes sediment buildup and extends the life of the water heater. • Double anode protection: Two heavy-duty magnesium anode rods help resist corrosion and extend tank life. • Energy-saving insulation: 3" of polyurethane foam cover 85% of the tank surface area, keeping heat in the tank to lower operation costs. • Standard Voltage is 240V: Other voltage options are available. • Units are Wired for 3 Phase: Can be changed to 1-Phase in the field.

Model No. HU ES50 HU ES85 HU ES120

Cap. Input Height Gal. kW Inches 50 6-54 43-5/8 85 6-54 57-11/16 120 6-54 57-11/16

Width Depth Wt. Inches Inches (lbs.) 26-1/4 32 241 28-1/14 34 332 28-1/4 34 408

D

Commercial

Storage Tanks

Model No. HU ES50-6G HU ES50-9-G HU ES50-12-G HU ES50-18-G HU ES50-24-G HU ES50-27G HU ES50-30-G HU ES50-36-G HU ES50-45-G HU ES50-54-G HU ES85-6-G HU ES85-9-G HU ES85-12-G HU ES85-15-G HU ES85-18-G HU ES85-24-G HU ES85-27-G HU ES85-30-G HU ES85-36-G HU ES85-45-G HU ES85-54-G HU ES120-6-G HU ES120-9-G HU ES120-12-G HU ES120-18-G HU ES120-24-G HU ES120-27-G HU ES120-30-G HU ES120-36-G HU ES120-45-G HU ES120-54-G

Gal. Wattage Rise GPH (Lbs.) Net Ea. 50 6 kW 25 241 $ 1991.00 50 9 kW 37 241 2120.00 50 12 kW 49 241 2140.00 50 18 kW 74 241 2210.00 50 24 kW 98 241 3195.00 50 27 kW 111 241 3240.00 50 30 kW 123 241 3287.00 50 36 kW 147 241 3352.00 50 45 kW 184 241 4235.00 50 54 kW 221 241 4370.00 85 6 kW 25 332 2615.00 85 9 kW 37 332 2669.00 85 12 kW 49 332 2679.00 85 15 kW 61 332 2735.00 85 18 kW 74 332 2768.00 85 24 kW 98 332 3480.00 85 27 kW 111 332 3799.00 85 30 kW 123 332 3830.00 85 36 kW 147 332 3869.00 85 45 kW 184 332 4832.00 85 54 kW 221 332 4864.00 120 6 kW 25 408 3035.00 120 9 kW 37 408 3121.00 120 12 kW 49 408 3135.00 120 18 kW 74 408 3212.00 120 24 kW 98 408 3212.00 120 27 kW 111 408 4173.00 120 30 kW 123 408 4178.00 120 36 kW 147 408 4216.00 120 45 kW 184 408 5367.00 120 54 kW 221 408 5410.00

FREIGHT-FREE FROM FACTORY!!

80, 115 & 175 Gallon

RHEEM-RUUD Commercial Storage Tanks are vertical tanks designed for applications that require large quantities of hot water in short periods of time. When used in tandem with Commercial water heating equipment, these storage tanks provide the flexibility needed for many Commercial applications. Installed individually or in parallel manifold, these storage tanks can provide 80% draw capability without an appreciable temperature decrease in single temperature applications.

LONG LIFE TANK DESIGN - Proprietary steel formulation with two coats of high temperature porcelain enamel to maximize corrosion resistance resulting in a superior tank design. Two heavy-duty magnesium anode rods are installed for longer tank life. SPACE SAVING DESIGN - Unlike other storage tanks, the ST80 and ST120 can pass through a 30" opening and the ST175 only requires a 33" opening - ideal for boiler room doors.

EFFICIENT DESIGN - 2" of rigid polyurethane foam insulation provides superior insulating qualities resulting in reduced operating costs. Our patented process of injecting foam into the insulating cavity adds additional durability and toughness to the baked enamel, steel outer jacket.

TANK OPENINGS - Circulating line connections and hot outlet are 2" NPT on the ST80 and ST120 and 2-1/2" NPT on the ST175. Other openings are provided for relief valve and temperature control. ST175 is equipped with a hand-hole cleanout. FREE Capacity Shipping Tank Information (English & Metric) Model No. Gallons Wt. Lbs. Net Ea. Maximum Working HU ST80 80 Non-ASME 220 $ 959.00 Model Tank Capacity Pressure HU ST80A 80 ASME 260 1665.00 Number Gallons Liters Ht. Dia. STD. ASME HU ST120 115 Non-ASME 300 1349.00 ST80 80 303 58-5/16” 24-7/16” 150 PSI 125 PSI HU ST120A 115 ASME 340 1949.00 1034kPa 862 kPa ST120 115 435 59-1/4” 28-1/4” 150 PSI 160 PSI HU ST175 175 Non-ASME 600 3029.00 1034 kPa 1103 kPa HU ST175A 175 ASME 600 3395.00 ST175 175 662 67-1/4” 32-1/4” 150 PSI 150 PSI Note: All tanks shown are prepaid from factory. 1034 KPA 1034 kPa (Larger tanks also available, But Not Prepaid). DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

D

E0674


Commercial Water Heaters

27

Electric Point of Use Water Heaters Point of Use Electric Water Heaters are designed to provide hot water at the consumption point which eliminates temperature loss in piping runs. Well suited for a wide variety of applications. Small enough for installations where space is limited and hot water is required. Available in tank or tankless styles.

EGS Models Feature: Steel tanks with a unique coating of porcelain/enamel for maximum corrosion resistance • Heating elements are treated with a double layer of magnesium oxide and copper to resist corrosion • Poly foam insulation provides superior insulating qualities • Surface mounted thermostat automatically cycles on/off to maintain desired temperature • Temperature and pressure relief valves are included. All models must be ordered with element output wattage and wiring voltage to meet specific applications as shown in the charts below Single phase wiring only.

D

DIMENSIONAL INFORMATION Tank Min. Max. Capacity Part No. Watts Watts Gallons HU EGSP6 1,500 6,000 6 HU EGSP10 1,500 6,000 10 HU EGSP15 1,500 6,000 15 HU EGSP20 1,500 6,000 19.9 HU EGSP30 1,500 6,000 30

D imensional Information in Inches A B C D E Wt. Inches Inches Inches Inches Inches Lbs. Net Ea. 15-1/8” 15-3/4” 12-5/8” 11-5/8” 4-1/4” 41 $ 521.00 22-7/8” 15-3/4” 20-3/8” 19-3/8” 4-1/4” 53 555.00 24-1/4” 17-3/4” 21-7/8” 19-3/8” 4-5/8” 65 595.00 25-1/8” 19-3/4” 22-5/8” 19-3/8” 5-1/8” 76 629.00 30” 21-3/4” 23” 23” 2-3/4” 115 1349.00

Water Thermostat Temperature Type: Ratings: Surface Mounted

Minimum Maximum High Temperature Temperature: Temperature: Limit: 110° F. (43.3° C) 170° F. (76.7° C) 190° F. (87.8°C)

Tankless Water Heaters — Continuous Hot Water —

RTE Tankless Instantaneous Heaters. Heats water only as you need it. Continuous hot water on demand. Compact design will fit almost anywhere. Power and external temperature controls. Rugged brass/copper heat exchangers. Ideal for a wide variety of uses in commercial, recreational or residential applications. 10-Year limited heat exchanger warranty. Water connections are 1/2” NPT.

D

RTE3 & RTE7

D

RTE9 & RTE13

DIMENSIONS Req’d Max. Power Part No. Length Width KW Volts Breaker (AMP) HU RTE3 10-1/4” 5-3/8” 3.2 110 30 29 HU RTE7 10-1/4” 5-3/8” 7 240 30 29 HU RTE9 10” 7-1/4” 9 240 40 38 HU RTE13 10” 7-1/4” 13 240 60 54 HU RTE18 10-1/2” 11-1/4” 18 240 (2) 40 75 HU RTE27 10-1/2” 11-1/4” 27 240 (2) 60 112 * Plumbing Connections: 1/2” NPT • Minimum Flow Rate: 1/2 gal. min.

DULTMEIER SALES

OMAHA, NE (800)

228-9666

AWG Wire 10 10 8 6 (2) 8 (2) 6

Wt. Lbs. Net Ea. 6 $ 219.00 6 219.00 8 219.00 8 239.00 12 423.00 12 669.00

DAVENPORT, IA (800)

553-6975

D

RTE18 & RTE27 •

www.dultmeier.com

E0964


Water Heaters • Relief Valves

Duct & Rail Heating Systems

HOT WATER GENERATORS Now you can have instant hot water from your cold water washer anytime you want it! Simply attach a “Hot Box” Hot Water Generator to your cold water pressure washer for instant hot water. Easily disconnected if you wish to go back to cold water cleaning. Available in sizes from 240,000 to 1,040,000 BTU’s. Units will develop at least 120° F. temperature rise above incoming water temperatures at the maximum flow rates shown. (Lower flow rates will increase output water temperatures accordingly). Series 240 430 560 1010

Width 22" 22" 22" 30"

Length 22" 22" 22" 36"

28

The perfect system to eliminate freeze problems in your Self-Serve supply ducts. Can also be used to prevent ice buildup on overhead track/rail assemblies on Automatic wash systems. Warm Water is circulated from a water heater through a piping loop in the duct or rail and then back to the heater. The heater is activated by a thermostat sensing outside air temperature. Available with either Gas or Electric water heaters

D

Height 56" 56" 50" 64"

D

Rail/Duct Heating Kits include: Gas Water Heater with a 30 gallon tank or Electric Water Heater with 6 gallon tank • Expansion Tank • Transfer Pump • Outdoor Thermostat • Pressure Relief Valve. Gas water heaters are rated at 32,000 BTU. Electric models are rated at 6000 watts and 240 Volt. Note: It is recommended that 1/2" copper tubing and valves be used for the loop in the ceiling and 3/4" from the heater and tank to the ceiling loop. These materials are not provided and must be ordered separately.

Standard Features Include: Automatic burner shutdown • Adjustable thermostat control • Schedule 80 Pipe • Flow switch • Kerosene, Diesel, Natural or LP Gas Fired • 110-Volt, 12-Volt or Millivolt burners (Millivolt system creates its own electricity from thermocouple and pilot) • Quick Couplers • Heavy gauge construction • Pressure Relief Valve • Fuel Tank on Oil-Fired Units • On-Off switch • 5 Year prorated coil.

Part No.

Heater Style

Gallons

Net Ea.

30 30 6

$ 785.00 949.00 639.00

HU P306N Gas, Natural HU P306P Gas, LP HU PEP6 Electric

Max. Wt. Part No. BTU †GPM PSI Fuel Voltage Lbs. Net Ea. DU 240 240,000 2.2 4000 Oil 110-Volt 275 $ 1555.00 DU 430 430,000 4.0 4000 Oil 110-Volt 300 1775.00 DU 560 560,000 5.0 4000 Oil 110-Volt 425 1985.00 DU 1010 1,010,000 10.0 4000 Oil 110-Volt 1095 4260.00 DU 240G 240,000 2.2 3500 * Nat/LP Milli-Volt 300 1575.00 DU 375G 375,000 4.0 3500 * Nat/LP Milli-Volt 340 1635.00 DU 500G 500,000 5.0 3500 * Nat/LP Milli-Volt 460 1850.00 DU 1040G 1,040,000 10.0 3500 * Nat/LP Milli-Volt 1080 4450.00 † Maximum Gallons per minute with a 120° F. temperature rise. 12-Volt Burner in place of 110 volt up to 360,000 BTU .................. CALL 12 Volt Burner in place of 110 volt up to 560,000 BTU & Larger..... FOR Add On for Electronic Ignition.......................................................... PRICING * Specify Natural Gas or LP Gas on these units.

DUCT HEATING SYSTEM with Electric Heater, Circulating Pump, Expansion Tank & Thermostat

dultmeier.com

Temperature & Pressure Relief Valves Bronze, Self-Closing T & P Relief Valves for gas, electric or oil-fired storage water heaters. Provides for complete protection against both excessive temperature and pressure emergency conditions. Standard Features: Accurate and proven thermostats in different lengths • Vacuum relief valve vent • Backup emergency safety fuse plug • Tamper-resistant bonnet screws • Rated to 210° F. • ASME rated • Pressure range is 75 - 150 PSI.

• Shop and Order On-Line 24 Hours a Day, 7 Days a Week! • Large Inventories of Over 3 Million Total Items! • View Current Pricing! • Web Specials and Bargain Corner!

WS 100XL3 WS 40L3 WS 40XL5 WS 40L2 WS 140S3 WS 140X6 WS 240X6 WS 3403

• Hundreds of Parts List Schematics (and more to come!) • Technical Library packed with information! • See New Items not Shown in Our Printed Catalogs! • Track Your Order Status and History! • Secure Site for Safe On-Line Ordering. OMAHA, NE (800)

228-9666

D

100XL 40L Series & 40XL Series

Thermostat Temp. Steam Part No. Inlet Outlet Length Rating, BTU/hr.

• Know Your Part Numbers? Use the Web Quick Order Page!

DULTMEIER SALES

D

3/4" M 3/4" M 3/4" M 1" M 1" F 1" F 1" F 1-1/2" F

DAVENPORT, IA (800)

3/4" F 3/4" F 3/4" F 1" F 1" F 1" F 1" F 1-1/2" F

553-6975

3" 3" 5" 2" 3" 6" 6" 3"

100,000 180,000 200,000 450,000 570,000 670,000 730,000 1,150,000

www.dultmeier.com

Net Ea.

$ 13.95 174.00 167.50 265.00 310.50 258.00 426.00 1094.00 E0021


Atmospheric Boilers

29

Finned Copper Tube Heat Exchanger single bank, straight through design delivers lowest pressure drop. Integral fins have 10 times the heat transfer surface of plain tubes.

Rugged All Bronze Headers resist corrosion and are easily removed for inspection or service. Cast iron headers with porcelainized waterways are available.

MODULATING ATMOSPHERIC BOILERS

24 Volt Controls are totally enclosed for protection. Door is easily removed for inspection and service.

Combination Modulating Valves automatically size boiler to loads as low as 20% of full input for maximum fuel economy.

Modulating Atmospheric Boilers from Raypak are ideal for hot water storage or for floor heat and snow melt applications. Non-ferrous (copper, bronze and porcelain) waterways will not rust and operate at temperatures as low as 105° F. without condensation. Copper finned design allows for use with less expensive, nonbarrier radiant tubing vs. traditional cast iron boilers. Efficiency rating is 82%. Modulating design increases efficiencies by using more or less gas as demand changes. Thermal shockproof heat exchangers are a standard feature. Exterior coating is a UV inhibited, powdercoat finish for years of durability.

Floating Return Header immunizes heat exchanger to thermal shock.

Corrosion Resistant Steel fittings are brush-galvanized against rust. Heat shields are corrosion-resistant steel. Jacket has Polytuf powder coat finish.

D

Tube Sheet & “O” Ring Construction eliminates the repair and maintenance problems associated with rolling tubes directly into a casting.

Call Toll-Free for Details & Pricing!

Interlocking Refractory Panels with sealed corners reduce radiation losses.

Stainless Steel Burners maintain precise combustion at all firing rates, burn quietly and won’t clog or corrode.

Slide Out Burner Tray allows easy inspection and service.

Spark-to-Pilot Ignition the most dependable ignition method available.

HYDRONIC BOILERS for Floor Heat, Snow Melt or De-Icing

HOT WATER BOILERS

Raypak Hydronic Boilers are designed to circulate warm fluid for Floor Heat, Snow Melt and De-Icing applications. The boilers shown are Natural Gas fired, but LP Gas units are available at nominal additional cost. Basic boilers come with appropriate draft hood. Packages that include boiler, pump/motor and air expansion tanks are also available. BTU ratings are for up to 2000’ elevations. Reduce by 4% for every additional 1000’ of elevation.

D

D

Wt. 191 lbs. 214 lbs. 234 lbs. 253 lbs. 455 lbs. 465 lbs. 575 lbs. 605 lbs. 705 lbs.

Net Ea. $ 2755.00 3035.00 3637.00 3745.00 5398.00 5998.00 6452.00 7420.00 8095.00

OMAHA, NE (800)

228-9666

Boiler shown with optional tank and manifolds

Two Stage Hot Water Boilers from Raypak. Designed to supply hot water needs for commercial and industrial applications. Ideal for use in Car and Truck Wash applications. Replacement boilers come with pump, pressure valve and temperature relief valve. (Packages with boiler and storage tanks are also available). Prices shown are Natural Gas fired but LP Gas is available at a nominal additional cost. BTU ratings are for up to 2,000’ elevation. Deduct 4% per additional 1,000’ elevation. * Max. BTU Pump Part No. Input HP Wt. Net Ea. HU WT2-9-18B 181,000 1/6 221 lbs. $ 3198.00 HU WT2-9-26B 264,000 1/6 244 lbs. 3465.00 HU WT2-9-33B 334,000 1/6 264 lbs. 3948.00 HU WT2-9-40B 399,000 1/6 283 lbs. 4050.00 HU WT2-9-51B 512,000 1/6 510 lbs. 5647.00 HU WT2-9-62B 627,000 1/6 520 lbs. 6213.00 HU WT2-9-72B 726,000 1/6 630 lbs. 6399.00 HU WT2-9-82B 825,000 1/6 660 lbs. 7105.00 HU WT2-9-96B 962,000 1/2 760 lbs. 8497.00 HU WT2-9-112B 1,125,000 1/2 800 lbs. 9088.00 HU WT2-9-122B 1,222,000 1/2 860 lbs. 9747.00 HU WT2-9-133B 1,337,000 1/2 930 lbs. 10670.00 HU WT2-9-146B 1,467,000 1/2 1000 lbs. 11065.00 HU WT2-9-163B 1,630,000 1/2 1040 lbs. 12445.00 * Ratings are for Natural Gas, LP ratings are slightly lower.

Boilers rated from 1.0 to 1.8 million BTU’s are available if required.

* Max. BTU Flue Part No. Input Size HU TD5-918B 181,000 6” HU TD5-926B 264,000 7” HU TD5-933B 334,000 8” HU TD5-940B 399,000 9” HU TD5-951B 512,000 10” HU TD5-962B 627,000 12” HU TD5-972B 726,000 12” HU TD5-982B 825,000 14” HU TD5-996B 962,000 14” * Ratings are for Natural Gas, LP ratings are slightly lower. DULTMEIER SALES

D

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E1020


FLOOR HEAT SYSTEMS

30

FLOOR HEAT SYSTEMS Keep your customers coming back all winter long with the installation of a floor heat system from Dultmeier Sales. A reliable floor heat system is essential to self-service car wash success. These systems have been field-tested winter after winter in car washes around the country. Systems are designed for 0° F. Note: -10° F. Systems also available. Standard components in all floor systems: Boiler with draft hood • flow switch • high limit aquastat • thermostats, expansion tank • circulating pump • slab thermostat • manifolds with test hardware • plastic underground pipe • wire ties and wire tie twister. Note: All manifolds are factory assembled and Pressure tested.

Call for a Price Quote Today !

Floor Heat Tubing & Accessories Cross-Linked Polyethylene tubing designed for the rigors of radiant floor heat systems. PEX tubing is designed for use in closed-loop, hydronic heating systems. This product is widely used in concrete floors such as car wash pads. Also can be used for warehouses, shops, garages, etc. Available in either 1/2" or 5/8" sizes and in 300' or 1000' standard packages. Ideally suited for 10" or 12" center spacing. Connector fittings and manifolds are also available and are shown below. For optimal results insulation should be considered in conjunction with the tubing installation. Call for complete system quotes and specifications. Concrete

Insulation (optional) Concrete Sand bed (optional) Insulation (optional) Base grade, ground

Tubing

** TUBING Part-No.

I.D.

O.D.

* Std Pkg

WU F1060500 1/2" .625 WU F1120500 1/2" .625 WU F1060625 5/8" .750 WU F1120625 5/8" .750

D

Manifolds

Per Roll Net Ea.

300' $ 117.00 1000' 398.00 300' 179.00 1000' 590.00

* Sold in standard packages only. ** For boilers with bronze headers only.

ACCESSORIES Part-No.

Description

WU A2503220 WU A2663212 WU A2523220 WU A2663213 WU A2663204 WU A2663214 WU E6081500 WU E6061000 WU E6122000

2-Run supply manifold less valves........ $ 19.95 2-Run return manifold with valves......... 73.20 3-Run supply manifold less valves........ 24.95 3-Run return manifold with valves......... 88.95 4-Run supply manifold less valves........ 67.95 4-Run return manifold with valves......... 103.50 Tubing Cutter, Ratchet Style.................. 22.00 Tubing Uncoiler..................................... 268.00 Air Pressure Test Kit.............................. 49.85

Net Ea.

Custom Engineering Drawings Available

Counter-flow - All snow-melt systems must be installed in a counter flow pattern which runs the warmest water in the loop next to the coolest. This is critical to ensure that all parts of the snow-melt floor heat area receive adequate supply temperature.

* Manifold end caps, connector fittings, mounting brackets etc. are also available, call for pricing.

DULTMEIER SALES

OMAHA, NE (800)

228-9666

REVERSE RETURN

LAYOUT PATTERNS

DAVENPORT, IA (800)

553-6975

Supply Return

www.dultmeier.com

E0022


Poly Cone-Bottom & PCO Tanks

31

Pest Control Operator (PCO) Tanks

Cone-Bottom Storage Tanks FEATURES: • High quality polyethylene with UV protection. • Molded-in deep tie-down lugs. • 12" or 16" Vented Lids • Molded-in gallonage markers. • 3 year warranty. • 14 Lbs./Gal. rating (16 Lbs./Gal. available) • Cone bottom for total drain-out. • 2” Poly Bulkhead Fittings. • Santoprene Gaskets • Heavy-duty cone-bottom steel stands.

D

Part No.

Gallonage Diameter & Cone x Height Lid

RT CB0150-36 150 Gallon-45˚ 36” x 51” 12" RT CB036-45ST Cone Bottom Stand RT CB0200-42 200 Gallon-45˚ 42” x 55” 12" RT CB042-45ST Cone Bottom Stand RT CB0350-42 350 Gallon-45˚ 42” x 81” 12" RT CB042-45ST Cone Bottom Stand RT CB0500-52 500 Gallon-45˚ 52” x 81” 12" RT CB052-45ST Cone Bottom Stand RT CB0800-86 800 Gallon-15˚ 86” x 48” 16" RT CB086-15ST Cone Bottom Stand RT CB1000-64 1000 Gallon-45˚ 64” x 98” 16” RT CB064-45ST Cone Bottom Stand RT CB1300-90 1300 Gallon-15° 90” x 65” 16” RT CB090-15ST Cone Bottom Stand RT CB1600-90 1600 Gal.-30˚ 90” x 85” 16" RT CB090-30ST Cone Bottom Stand RT CB2600-90 2600 Gallon-30˚ 90” x 123” 16" RT CB090-30ST Cone Bottom Stand RT CB2600-86 2600 Gallon-45˚ 86” x 146” 16" RT CB086-45ST Cone Bottom Stand RT CB3000-90 3000 Gallon, 15˚ 90” x 128” 16" RT CB090-15ST Cone Bottom Stand RT CB4600-102 4600 Gallon, 15˚ 102” x 155” 16" RT CB4900-102 4900 Gallon, 15˚ 102” x 159” 16" RT CB102-15ST Cone Bottom Stand RT CB6900-122 6900 Gallon, 15˚ 122” x 168” 16" RT CB8250-122 8250 Gallon, 15˚ 122” x 195” 16" RT CB122-15ST Cone Bottom Stand RT CB1000-90 1000 Gallon, 15° 90” x 54” 16” RT CB1300-90 1300 Gallon, 15° 90” x 65” 16” RT CB090-15ST Cone Bottom Stand (for 1000 & 1300 Gallon Tanks) F.O.B. Factory

Net Ea.

$ 235.50 206.50 256.50 234.00 407.50 234.00 396.16 347.50 528.00 764.00 783.48 599.00 727.00 779.00 809.00 974.00 1315.00 974.00 1314.00 966.00 1407.00 779.00 2963.00 3270.00 1053.00 4075.00 4979.00 2294.00 583.52 727.00 779.00

These rectangular tanks are commonly referred to as “Pest Control Operator” tanks since they include many desirable features for the pest control operator and other users. • Use for stationary or transportable (non-D.O.T. regulated) applications: indoors & outdoors. • Tanks have a rounded bottom for best liquid drainage and optional 2” deep x wide sump. • Constructed of medium-density polyethylene with U.V. inhibitors: rated to 14 lbs/gal. • 300 Gallon tanks D include an internal baffle for support & liquid control. • Securely anchor for use in transport applications; use powder coated steel bands shown. • Translucent white color is standard; gallonage markers included. • “Notched” recess at top in 4 places so bands hold tank more securely from sliding.

PCO Tanks Part No. Description Dimensions Lid Fitting RT PCO35 35 Gallon No Sump 16”x35”x21”H 5" 1" RT PCO50 50 Gallon No Sump 19”x38”x23”H 8" 1" RT PCO50S 50 Gallon With Sump 19”x38”x23”H 8" 1" RT PCO100 100 Gallon No Sump 30”x38”x29”H 8" 1" RT PCO100S 100 Gallon With Sump 30”x38”x29”H 8" 1" RT PCO150 150 Gallon No Sump 37”x48”x29”H 12" 1-1/4" RT PCO150S 150 Gallon With Sump 37”x48”x29”H 12" 1-1/4" RT PCO200 200 Gallon No Sump 37”x48”x38”H 12" 1-1/4" RT PCO200S 200 Gallon With Sump 37”x48”x38”H 12" 1-1/4" RT PCO300 300 Gallon No Sump 37”x69”x40”H 16" 2" RT PCO300S 300 Gallon With Sump 37”x69”x40”H 16" 2" Band Pairs (Powder Coated Silver): Part No. Description Dimensions RT PCO35SB *One Pair - 35 Gallon Tank 2” x 50.5” RT PCO50SB One Pair - 50 Gallon Tank 2.5” x 57.5” RT PCO100SB One Pair - 100 Gallon Tank 2.5” x 76” RT PCO150SB One Pair - 150 Gallon Tank 3.5” x 82” RT PCO200SB One Pair - 200 Gallon Tank 3.5” x 98” RT PCO300SB One Pair - 300 Gallon Tank 4” x 100” * Bands for 35 Gallon Tank are Stainless Steel.

Wt. Net Ea. 25 lbs. $ 106.50 25 lbs. 117.00 25 lbs. 117.00 50 lbs. 182.00 50 lbs. 182.00 61 lbs. 219.00 61 lbs. 219.00 82 lbs. 271.00 82 lbs. 271.00 160 lbs. 514.00 160 lbs. 579.00 Wt. 3 lbs. 6 lbs. 10 lbs. 15 lbs. 18 lbs. 20 lbs.

Net Ea. $ 28.40 34.26 37.68 52.78 76.12 95.93

H2O Water Only Tanks 2500 & 3000 Tanks These Water Only Vertical Tanks are freestanding for indoor or outdoor stationary applications. They are designed for the storage of water or other light liquids compatible with polyethylene and with a specific gravity of 1.0 or less (8.34 lbs./gal. or less). They are manufactured from FDA compliant high-density polyethylene with U.V. stabilizers. The tanks minimize algae formation due to their dark green color.

Cone Bottom Storage Tanks 175 Gallons thru 500 Gallons • Heavy duty polyethylene with ultraviolet inhibitors added for protection against sunlight. Poly stands. • Offset fillwell & cover standard.

D D

• Sidewall flat for recirculation. • 30° cone for tanks. • Molded-in gallonage marks. • Standard color is White.

WARRANTY: 3-Year from factory ship date on cone bottom storage tanks - non-mobile applications.

NOTE: These tanks designed for 12 lb/gal. liquids.

D

– Cone Bottom Tanks with Poly Stands – Poly Part No. Capacity Diameter Height Fillwell Fitting Net Ea. RV 60113 175 Gallon 42" 49" 10" 3/4" $ 463.50 RV 62441 310 Gallon 42" 71" 16" 2" 574.00 RV 40289 500 Gallon 48" 85" 16" 2" 853.00 DULTMEIER SALES

OMAHA, NE (800)

228-9666

Part No. Gallons Dimensions Outlet Fitting Lid Wt. Net Ea. RT WO2500-VT 2500 96” x 92” 2” 16” 392 lbs. $ 1014.00 RT WO3000-VT 3000 96” x 109” 2” 16” 487 lbs. 1208.00 •

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E1005


STORAGE TANKS 400 Gallon Utility Tank

Storage Tanks

— Slim Line Style — Slim Line Storage Tank. Polyethylene Tank designed for narrow installations. Depth is only 29". Width is 62" and height is 66". Standard with 2" outlet fitting and 16" vented lid. Built-in gallonage indicators are molded into each end of tank. Rated for products up to 1.70 specific gravity. Color is white.

32 TANK FEATURES • Maximum Temperature is 140° F. • Flat spots located on bottom sidewall for additional fitting installation. • Two top-edge molded-in lugs for sure & safe tie down on 150 Gallon & Larger.

66"

• Heavy-duty polyethylene with ultra-violet inhibitors added for protection against sunlight. • Built-In Gallonage indicator. D

• Standard color is yellow. White Also Available.

D

62

"

Part No.

RT SPO400UT

Gallons

Wt.

400

207 lbs.

Net Ea.

65 to 3,000 Gallons

29"

$ 605.00

Narrow Poly Vertical Tanks 55 to 1500 Gallon These Polyethylene Tanks have been designed with a narrow diameter for tight places and for use in containment dikes. DESIGNED FOR PRODUCTS WEIGHING UP TO 14 LBS./GALLON

Fitting Siphon Wt. Part No. Capacity Dia. Ht. Filwell Size Tube Lbs. Net Ea. RV 41347 65 Gallon 23" 42" 8" 1-1/4” No 18 $ 108.00 RV 47333 110 Gallon 29" 42" 10" 3/4" No 36 159.00 RV 41856 * 200 Gallon 30” 72” 8” 2” Yes 52 253.00 RV 47399 210 Gallon 32" 69" 10" - No 59 260.50 RV 47401 * 210 Gallon 32” 69” 16” 2” No 59 260.50 RV 47484 * 300 Gallon 35" 80" 10" 2" Yes 80 319.50 RV 41339 550 Gallon 67" 42" 16" 2" Yes 105 399.50 RV 47713 1100 Gallon 84" 57" 16" 2" No 175 582.00 RV 47811 1350 Gallon 84" 69" 16" 2" Yes 204 702.00 RV 45218 1550 Gallon 87" 65" 10" 2" Yes 283 773.00 RV 45082 3000 Gallon 91” 115” 16” 2” Yes 465 1722.00 * White Tank.

Storage Tanks

• Medium & High Density Polyethylene

Rotationally Molded Polyethylene - Yellow Color is Standard (White is also available)

• Ultraviolet Inhibitor • Translucent • Gallonage Markers • Siphon Tube Included on 300 Gallon & Larger Tanks

D

• 3 Year Warranty Part No. RT VT0055-20 RT VT105 RT VT0135-28 RT VT0175-31 RT VT0225-31 RT VT0300-35 RT VT0425-42 RT VT0505-46 RT VT0600-46 RT VT0800-46 RT VT1000-64 RT VT1500-64

D

• Rectangular "Leg" Tanks

Gallons Diameter Height Drain Fillwell Wt. Net Ea. 55 20" 47" 1" 5" 22 lbs. $ 93.25 105 23" 65" 1" 8" 38 lbs. 161.50 135 28" 59" 1" 8" 47 lbs. 170.00 175 31" 61" 1-1/2" 8" 54 lbs. 198.50 200 31” 76” 2” 8” 65 lbs. 261.50 300 35" 81" 2" 8" 86 lbs. 320.00 425 42" 75" 2" 8" 73 lbs. 324.50 505 46" 80" 2" 16" 118 lbs. 423.00 600 46" 91" 2" 16" 130 lbs. 463.50 800 46" 118" 2" 16" 175 lbs. 534.00 1000 64" 81" 2" 16" 250 lbs. 709.00 1500 64” 115” 2” 16” 335 lbs. 1056.00

• 5" Fillwell & splash guard on 30 to 100 Gallon. 10" Fillwell & splash guard on 200 & 300 gallon. • Flat area on each end for fittings or agitation (order fittings separately). • Attractive compact design requiring no complex saddling or support structures.

Truck/Trailer Tanks 500 & 750 Gallons Features: Low profile for added visibility & easy-reach filling • Ribbed for extra strength • Molded D in baffle • Optional extra deep single/ double sump for drainage • Four flat spots on both ends for fitting installations • Circumferential lip around fillwell to contain spills with drainage channel to rear of tank • Large 16" fillwell is standard • Integral safety/fresh water tank included • Easy compliance with EPA regulations.

Lid Part No. Capacity Size Width Height Length Wt. RV 47024 15 Gallon 5" 12" 15" 25" 35 lbs. RV 47022 30 Gallon 5" 19" 20" 25" 16 lbs. RV 47013 50 Gallon 5" 19" 20" 38" 23 lbs. RV 47016 * 50 Gallon 5" 19" 20" 38" 26 lbs. RV 47020 100 Gallon 5" 30" 26" 38" 42 lbs. RV 47017 * 100 Gallon 5" 30" 26" 38" 42 lbs. RV 47350 150 Gallon 10" 36" 26" 48" 63 lbs. RV 47352 200 Gallon 10" 36" 35" 48" 80 lbs. RV 47359 300 Gallon 16" 36" 35" 69" 133 lbs. * White Tank.

Part No. RV 47203 RV 47084

Capacity 500 Gallon 750 Gallon

DULTMEIER SALES

228-9666

Water Storage Tanks for below ground installations. Ideal for use with RO water for spot-free rinse systems or for Potable water storage. Constructed of one-piece, seamless polyethylene. Self-locking covers are standard. 850 gallon tanks feature (1) 24" manhole with lid. 1150 gallon tank features (2) 24" manholes with lids. 1200 & 1700 gallon tanks feature (2) 20" manholes with lids. Note: Tanks are F.O.B. Factory.

Part No. Gallons Size Wt. Net Ea. RT AST850-1W 850 70"L x 60"W x 60"H 259 lbs. $ 1276.00 RT AST1150-1W 1000 101"L x 60"W x 60"H 414 lbs. 922.00 CU TN1200WT 1200 102"L x 60"W x 58"H - CALL CU TN1700WT 1700 143"L x 55"W x 66"H - CALL

Wt. Net Ea. 168 lbs. $ 628.00 254 lbs. 768.00

OMAHA, NE (800)

Net Ea. $ 82.75 106.50 117.00 117.00 186.00 186.00 225.00 281.50 669.00

Below Ground Water Storage Tanks

D

– TANKS Only – Width Height Length 48" 31" 90" 52" 40" 110"

• Molded in gallonage indicators on end and sidewall. • Ribbed for extra strength with U-V inhibitors added for protection against sunlight. • Outlet fittings must be ordered separately. • 300 Gallon tank is standard with baffle.

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0024


Poly Tanks

33

Low-Profile

Horizontal Leg Tanks

PICK-UP TANKS

65 to 1650 Gallons

205, 305 325 & 450 Gallon Capacity

These Polyethylene Tanks are Designed for 12 lb. Material

PICK-UP TANKS will fit most pick-up beds. Features: Low profile for good visibility and low center of gravity • 2" bulk head withdrawal fitting • Positive lock fill well cap • Engineered design permits efficient use of space • Extra deep recess in fill well area reduces spillage during filling and while moving over rough terrain • Rated to 12 lbs./Gal. • Molded gallonage indicator.

D

47361 47168 Capacity (Gal.) 210 325 Height* 28" 34" Length 60" 62" Base Width 48" 48" O.A. Width 53" 59" Fill Well 10" 10" Weight 105 120

GMC Sierra 1500,2500,3500; Toyota Tundra; & Lincoln Mark LT.

Capacity

Capacity

Dia. Length Fillwell

Wt.

Net Ea.

43” 5" 27 lbs. $ 134.50 49” 5" 72 lbs. 315.50 68” 16" 100 lbs. 385.00 75" 16" 139 lbs. 527.00 75" 16" 172 lbs. 527.00 107" 16" 246 lbs. 803.00 139" 16" 302 lbs. 1097.00 139" 16" 400 lbs. 1872.00

Hold Down Hoops for Leg Tanks Part No.

Description Net Ea.

RV 61745 RV 60478 RV 67101 RV 67246

One Hoop for 23" Diameter Tank.........................  $ 22.85 One Hoop for 38" Diameter Tank......................... 50.70 One Hoop for 48" Diameter Tank......................... 57.95 One Hoop for 62" Diameter Tank......................... 87.00

Narrow Width 2400 Gallon Horizontal Leg Tank D

Fits Inside Standard Dump Truck Beds • Only 78” Wide x 120” Long. Fitting

2” 2” 2”

Dia. X Ht.

Wt.

Net Ea.

52” x 30” 54 lbs. $ 175.50 62” x 34” 92 lbs. 302.50 62” x 41” 102 lbs. 313.00

200 & 300 Gallon Low Profile Poly Tanks

D

Gallon Required Size Hoops Dia. 65 2 23" 225 2 38" 325 2 38" 500 2 48" 750 3 48" 1000 4 48" 1650 4 62"

* White in Color.

Pick-Up Tanks

RT PU200 200 Gallon with 8” Lid RT PU350 350 Gallon with 8” Lid RT PU450 450 Gallon with 8” Lid Note: Siphon tube included.

Part No.

RV 45197 65 Gallon 23" RV 41344 225 Gallon 38" RV 41345 325 Gallon 38" RV 47256 * 500 Gallon 48" RV 47358 500 Gallon 48" RV 47211 750 Gallon 48" RV 47274 1000 Gallon 48" RV 47191 1650 Gallon 62"

Part No. Gallon Color Lid Size Net Ea. RV 47168 325 White 10” $ 329.00 RV 47407 450 White 10” 418.72 RT PU205 * 205 White 7” 275.00 RT PU305 † 305 White 7” 329.00 * Tank fits Ford Ranger, GMC Canyon, Chevy Colorado, Dodge Dakota, Nissan Frontier & Toyota Tacoma † Tank fits Ford F150,F250,F350; Dodge Ram 1500,2500,3500; Chevy Silverado 1500,2500,3500;

Part No.

Features: Self-supporting molded-in legs • 2" siphon withdrawal is standard • Heavy duty polyethylene with ultra-violet inhibitors added for protection from sunlight • Gallonage indicators • Hold down hoops are available • Standard color is yellow. Note: #47256 is white in color. Nurse Tanks

* Height to top of lid - 4" above top edge.

These economical pick-up tanks are used as applicator tanks or when transpor table (non D.O.T. regulated) containment is required. Designed to fit most full size pickup trucks with containment of liquids up to 1.7 specific gravity. Made from medium-density polyethylene with U.V. inhibitors. Translucent tank walls for level viewing; equipped with gallon indicators.

D

Features: Low profile for mobile or stationary applications • Rated for 14 lb./gal. products • Medium density polyethylene with UV stabilizers • Gallonage indicators on one side and end • Two recesses for anchoring bands • Steel band kit includes silver powder coat finish.

Part No. Capacity Lid Fitting Dimensions RT LP0200-RT 200 Gallon 8" 1" 48”x60”x19” H RT LP0300-RT 300 Gallon 8” 2” 80”x48”x21” H RT LP0200-SBP 200 Gallon Band Kit................................ RT LP0300-SBP 300 Gallon Band Kit................................ DULTMEIER SALES

Wt. Net Ea. 84 lbs. $ 263.50 135 lbs. 410.00 14 lbs. 51.20 16 lbs. 66.25

OMAHA, NE (800)

228-9666

• 77” Tall to Manway (Less Skid). • Molded in Baffles. 16" Top Lid. • Optional Steel Skid - Required with Bottom Sump. • 2” or 3” Bulkhead Fittings Polypropylene or Stainless.

D

• 15 Lb./Gallon Rating. • Hoops Included.

Tank with optional skid

Part No. RT FS2400 Tank without Sump RT FS2400S Tank with Sump RT FS2400-SKW Skid for Tank without Sump RT FS2400-SK Skid for Tank with Sump Note: Skids are available DAVENPORT, IA (800)

553-6975

Call for Pricing!

www.dultmeier.com

E0887


STORAGE TANKS

34

Open Top Storage Tanks Rectangular, Polyethylene Tanks for chemical storage. One-piece, molded construction means no seams to leak. Excellent chemical resistance. Translucent for visible contents level. Tanks come with lids. Rated to 140° F.

Height (H)

D

Len

gth

(L)

)

th (W

Wid

Part No.

Size

CU R6X1212A 6"W x 12"L x 12"H CU R1212 12"W x 12"L x 18"H CU R1224 12"W x 24"L x 18"H CU R1824 18"W x 24"L x 18"H

Capacity

Net Ea.

5 Gallon 11 Gallon 22 Gallon 37 Gallon

$ 54.95 97.90 124.00 135.00

- Stackable to 3 High -

Bulk Storage Tank This 70 Gallon free standing stackable leg tank is ideal for storing bulk chemical products, including oil, up to 1.7SG (14# liquids). Medium density polyethylene with UV inhibitors. 24” deep x 39” long x 30” high with 5" lid and 1" outlet. Has band locators for tie down if required. Translucent walls for viewing with gallon indicators. Note: Not for diesel, fuel or waste oil. For New oil only.

D

Part No. Description Wt. Net Ea. RT FS0070-24 70 Gallon Leg Tank.................... 38 lbs. $ 148.50

Small Storage Tanks - Bottom is Sloped to Drain • Rated for 14 lb./gal. liquids • Translucent (off-white)

Rectangular Storage Tanks

• Gallonage Indicators

- Flat Bottom -

• “Loaf” or rectangle style

D

• Grooves for straps

• Rated for 14 lb./gal. liquid • Translucent (off-white) • Gallonage indicators. • 5” Lid

• 5” Lid

SP8-VM SP19-VM

SP5-RT

Part No.

Capacity

Style

Fitting

W x L x H

Net Ea.

RT SP8-VM 8 Gallon RT SP12-RT 12 Gallon RT SP19-VM 19 Gallon RT SP20-LC 20 Gallon

Loaf Rect. Loaf Rect.

1/2” 3/4” 1/2” 3/4”

12”x16”x17” 14”x18”x12” 12”x16”x28” 14”x28”x12”

$ 47.09 50.72 70.05 65.85

D D

SP6-5N

SP20-OM

Part No.

Capacity

RT SP002.8RT 2.8 Gallon with 5” Lid RT SP5-RT 5 Gallon with 5” Lid RT SP6-5N 6 Gallon with 5” Lid RT SP7-RT 7 Gallon with 5” Lid RT SP16-MM 16 Gallon with 5” Lid RT SP20-OM 20 Gallon with 5” Lid RT SP55-MM 55 Gallon with 5” Lid

Fitting

None None None None None 1/2” 1”

W x L x H

Net Ea.

VT0025-18

9”x14”x9” $ 29.25 10”x22”x8” 34.80 12”x15”x8” 37.40 9”x14”x15” 41.80 14”x21”x14” 48.60 11”x15”x31” 801.00 18”x18”x45” 116.00

10, 20, 25, 40, 65, 75, 100 & 210 Gallon These polyethylene tanks are great for tight spots. 20, 25, 40, 75 and 100 gallon tanks are white and rated to 16 lbs./gal. 65 and 210 gallon tanks are yellow and rated to 12 lb./gal.

D

VT0100-28

Rectangular Utility Tanks

Vertical Polyethylene Storage Tanks

VT0040-18

Part No. Gallons Height Diameter Outlet Fitting Lid Net Ea. RT VT0010-12 10 25" 12" 3/4” 8” $ 50.60 RT 2026 20 28” 16” 3/4” & 1/2” * 8” 73.25 RT VT0025-18 25 30" 18" 3/4” 5” 59.85 RT VT0040-18 40 43" 18" 3/4” 5” 74.25 RT VT0075-23 75 50” 23” 1” 7” 116.00 RT VT0100-28 100 45” 28” 1” 7” 154.00 RV 41347 65 43" 23" 1-1/4" FPT 8” 108.00 RV 47399 210 69-1/2" 32" 2" FPT 16” 260.50 * 1/2” Fitting near top and 3/4” near bottom on 2026 tank.

- Flat Bottom • Rated for 14 lb./gal. liquid • Gallonage indicators • Translucent (off-white) • Grooves for straps • Optional Powder-Coated Tie Down Bands (sold separately)

White Poly Leg Tanks • Rated to 14 lbs./Gal. • Translucent

D D

SP68-RT

SP26-RT

Part No.

Capacity

Fitting

W x L x H

OMAHA, NE (800)

228-9666

D

• Larger Sizes Available • Optional Tie Down Bands

Net Ea.

Part No. Description

RT SP26-RT 26 Gallon with 8” Lid 3/4” 18”x25”x19” $ 80.75 RT SP68-RT 68 Gallon with 6” Lid 1” 26”x42”x17” 166.00 RT SP80-RT 80 Gallon with 5” Lid 1” 18”x27”x45” 156.00 RT SP100-RT 100 Gallon with 8” Lid 1” 27”x43”x26” 177.00 RT SP0200RT 200 Gallon with 8” Lid 1” 36”x48”x34” 259.00 RT SP80-SBP Band Set for 80 Gallon Tank.................... 38.20 RT SP100-SBP Band Set for 100 Gallon Tank.................. 37.35 RT SP0200-SBP Band Set for 200 Gallon Tank.................. 42.50 Note: Other sizes available. DULTMEIER SALES

• Gallon Indicators

RT FS0035-18 RT FS0125-32 RT FS0165-32 RT FS0225-38 RT FS0325-38 RT FS0035-B RT FS0125-B RT FS0225-B •

DAVENPORT, IA (800)

Dimensions Lid Outlet Net Ea.

35 Gallon Leg Tank 18” x 34” 5" 1” $ 69.35 125 Gallon Leg Tank 32” x 40” 8" 1” 217.50 165 Gallon Leg Tank 32” x 54” 8” 1” 269.00 225 Gallon Leg Tank 38” x 52” 8” 2” 310.50 325 Gallon Leg Tank 38” x 72” 8” 2” 374.50 Band Set with feet for 35 Gallon Leg Tank......... 27.65 Band Set with feet for 125/165 Gallon Leg Tank........ 42.35 Band Set with feet for 225/325 Gallon Leg Tank........ 95.50

553-6975

www.dultmeier.com

E0618


Soap • Wax • Fuel Tanks

35

Automatic Liquid Supply Tanks

Automatic Tank Mixing Systems

– Plastic Mixing Valve mounted inside tank

Wall mounted, automatic mixing tanks. Available in single or triple tank units.

Automatic Liquid Supply Tank. No more hand mixing, this tank will do it for you!! Heavyduty plastic construction. Standard with a 5 or 10 gallon per minute HydroMinder valve for exact mixture of solutions. Diameter is 16" x 28" high. Standard with a 8" locking lid. Note: Discharge from tank can be through the top or a bottom fitting (not included but can be supplied).

D

Features: • Wall Mount • Stainless Steel Frame • Plastic Tanks • Hydrominder Mixing Valves • 6” x 6” x 12” Plastic Tanks • Can be mounted in tandem for one through six chemical products if needed.

AP3

AP1 D

Part-No

Wt.

Net Ea.

DU AP20T 20 Gallon Auto Mix Tank, 5 Gal/Minute.... ­­20 lbs. $195.50 DU AP20T-2 20 Gallon Auto Mix Tank, 10 Gal/Minute.. 20 lbs. 296.50 RT 2026 Tank Only................................................. ­­ 13 lbs. 73.25

D

D

Part No. Tanks DU AP1 1 DU AP3 3

AUTOMATIC LIQUID SUPPLY TANKS

D

Specifications: 16-Gauge • 304 Stainless Steel • Height-24", Width-24", Depth-12" • Discharge port is (2) 3/4” on WT15B and (2) 1" on WT15B-1 • Approximate usable capacity is 27-Gallons • Stainless lid is included • Weight is 40 lbs. Part-No.

Net Ea.

Ideal For: • Wax • Brush • Soap • Tire Cleaners • Pre Soaks

DU AP5TS

10”

Automatic Mixing Tank.... $ 213.00

Polyethylene Fuel Tanks

Specific Part No. Capacity Dimensions Gravity Wt. Net Ea. RT OP0055-2DC (2) 55 Gal. Drums 34” x 62” x 26” 1.7 70 lbs. $ 145.50

228-9666

12”

Part-No. Net Ea.

This Open Top Tank is designed for secondary containment for 55 gallon drums or other small tanks in indoor or outdoor installations. Tank is manufactured from polyethylene with U.V. inhibitors. Black only.

OMAHA, NE (800)

D

1/2” FPT Outlet

Open Top Containment Tank

DULTMEIER SALES

AP5TS

Space Saving, Stainless Steel, Automatic Mixing Tank. This compact unit is only 10” wide, 12” tall and 6” deep. Includes tank, lid, wall bracket and Hydrominder mixing valve. Outlet is 1/2” FPT in the bottom of the tank. Designed for wall mounting.

DU WT15SS Complete Unit, 3/4” Ports............ $ 589.00 DU WT15B Stainless Tank Only, 3/4” Ports.... 483.00 DU WT15B-1 Stainless Tank Only, 1” Ports....... 482.50

D

Net Ea. $ 449.50 786.00

Wall Mount Auto Mix Tank

– Stainless Steel Automatic Stainless Steel Wax or Liquid Soap Tank: No more watching, measuring or mixing. Standard with a “Hydrominder” valve for automatic mixing from a bulk pail or drum. When solution level in tank drops, water source opens and combines with chemical for accurate consistent mix. For tank only use WT15B or WT15B-1.

Wt. 15 lbs. 43 lbs.

Made from high-density crosslinked polyethylene with UV stabilizers. Designed to hold gasoline, diesel and other compatible chemicals weighing up to 14.5 lbs./ Gal. Standard in black color with one 1/4” brass bulkhead fitting in the bottom.

D

SP12B

Part No.

Capacity

Dimensions

Lid

Net Ea.

RT SP6B RT SP12B

6 Gallon 12 Gallon

10”x15”x10” 14”x18”x12”

2” 2”

$ 73.74 83.84

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0023


Tanks & Tank Fittings

36

Fittings for Poly or Fiberglass Tanks Polypropylene Fittings

Stainless Steel D

Float Tanks Ideal for use with float valves for water supply to wash stations. Heavy 18-gauge construction. Tanks have 6" high internal baffles to reduce turbulence. Outlet fittings are on bottom side. Standard with foot flanges for mounting. WT3B: 6" wide x 11" high x 15" long. (1) 1/2" FPT inlet. (1) 3/4" FPT outlet.

Part-No.

Net Ea.

DU WT3B S.S. Float Tank $ 216.50 DU WT5B S.S. Float Tank 257.50

WT5B: 18" wide x 11" high x 15" deep. (1) 3/4" FPT inlet port. (1) 1" FPT outlet ports.

FLOAT TANK with LID

D

Part-NO.

Net Ea.

NP ST10-11 Float Tank with Lid $ 11.90 NP ST8K Adapter Kit............ 4.51

Stainless Steel Wall Mount Tank Wall Mount Storage Tank. Ideal design where space is a problem. Can be used for brush, tire cleaner, presoak systems, etc. Stainless steel construction. Complete unit includes tank, shelf and lid Dimensions are 10" x 12" x 6". Bottom outlet is 1/2" FPT. Lid designed for use with hydrominders. Part No. Net Ea. DD 61012 Stainless Steel Wall Tank with Stand......... $ 84.05

Stainless steel multi-compartment holding tanks for soap, wax, brush detergents, tire cleaners, etc. Can be easily plumbed for float valves or mixing valves.

Model 2208 is a two compar tment tank. Dimensions are 24" H x 24" D x 12" W. Each compartment is 6" wide with (1) 3/4" FPT inlet and (2) 3/4" FPT outlets in bottom. Lid is removable.

Model WT33 is a three compartment tank which is ideal for multi-colored brush or wax systems. Dimensions are 24" H x 12" D x 18" W. Each compartment is 5" wide with (1) 1/2" FPT inlet and (1) 3/8" FPT outlet in the lower front. This tank is designed to be wall mounted and includes brackets. Lid is removable.

WT33

Model 4275 is a large holding tank for use with multiple pumps. Dimensions are 24" H x 24" D x 36" W. Water compartment features (1) 3/4" FPT inlet and (6) 3/4" FPT outlets in bottom. Soap and wax compartments feature (1) 1/2" FPT inlet and (3) 1/2" outlets. Lid is hinged for easy access.

DULTMEIER SALES

67152

REQUIRED HOLE SIZE (I.D.): FPT Description Fiberglass 1/2" Double Thread 2-1/8" 3/4" Double Thread 1-5/8" 1" Double Thread 2-1/8" 1-1/4" Anti-Vortex 3-1/4" 1-1/2" Double Thread 3-1/4" 2” Double Thread 3-1/4”

Part No. RV 67161 TK TF075 RV 67162 RV 67152 RV 67154 RV 60405

D

Poly Net Ea. 1-11/16” $ 10.15 1-5/8” 5.83 1-11/16” 10.15 2-13/16” 12.20 2-13/16” 12.20 3” 5.50

D

EPDM VITON® Part No. FPT Size Hole Size Gasket Gasket Net Ea. TK TF050 1/2" 1-5/8" 150G 150GV $ 5.83 TK TF075 3/4" 1-5/8" 150G 150GV 5.83 TK TF100 1" 2-1/4" 200G 200GV 6.90 TK TF125 1-1/4" 2-1/4" 200G 200GV 8.02 TK TF150 1-1/2" 3" 300G 300GV 12.30 TK TF200 2" 3" 300G 300GV 12.32 TK TF220 2" 3-1/4" TF220G TF220GV 15.07 TK TF300 3" 4-1/2" TF300G TF300GV 26.39 TK TF400 4” 5-3/4” - - 60.79 RT 10508 2", 3" Santoprene Gasket............................. 7.02

316 Stainless Steel Tank Fittings Double Sided Threads • Standard with EPDM Gaskets • Viton® Gaskets are available

Outside Part No. Size Diameter Net Ea. TK TF075SS 3/4" 1-5/8" $ 92.60 TK TF100SS 1" 2-1/4" 112.70 TK TF125SS 1-1/4" 2-1/4" 112.70 TK TF150SS 1-1/2" 3" 141.58 TK TF200SS 2" 3" 141.58 TK TF220SS 2" 3-1/4" 188.00 TK TF300SS 3" 4-3/8" 228.97

D

Fillwells, Covers & Accessories

Multi-Compartment Holding Tanks

Part No. S.S. Tank Net Ea. DD WT33 3-Compartment $ 591.00 DD 2208 2-Compartment CALL DD 4275 3-Compartment 1600.00

67161

• Double Sided Threads • Standard with EPDM Gasket, Viton® Fluoroelastomer Is Optional

ST-8K Adapter Kit: 1/2" MPT x 1/2" MPT with lock nuts for plumbing float valves to ST10-11 tanks.

D

Standard with EPDM O-Rings - for Poly Tanks -

Polypropylene Tank Fittings

Plastic Float Tank for water supply to pumping units. Dimensions: 13" long x 5" wide x 6" deep. Molded 3/4" MPT outlet in bottom of tank is raised to prevent sediment from entering flow line. Lid is included.

D

D

D

4275

D

D

D

D

5479R

62476

5469R

5478R D D

60019 Fits 60011 Lid 60011

D

ST10W

Part No. Size Net Ea. DT 5479R 10" Fillwell..................................................................... $ 9.15 DT 5464R 16" Fillwell .................................................................... 5.53 RV 62476 5" Lid for Polytanks (New Style after 2001) ............... 4.55 DT 5478R 10" Lid, New style for Polytanks.................................... 13.90 RV 60011 16" Lid with 60019 4" Vent Cap ................................... 14.80 RV 60019 4" Vent Cap for 60011 Lid .......................................... 5.84 RT LD30-101 5” Lid with spring vent for spot sprayer tanks.............. 5.22 RV 63480 8” Lid with Snap-In Vent, After 2/2/2008..................... 7.50 DT ST10W - 14-Mesh Basket Strainer for 10" Fillwell................. 33.00 RV 60366 - Gasket for 5” Lid..................................................... 4.20 DT 5078R - Gasket for 10" Lid................................................... 3.00 RV 5449R 4' Poly Welding Rod .................................................. 15.60 RV 5469R 6" Threaded Lid with Vent for ARAG 12”,16” & 20” Lids.. 5.78 Viton® is a registered trademark of DuPont Performance Elastomers

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0025


Wheel & Tire Foamers • Foam Sticks

37

Wheel & Tire Foamers

Foam Sticks

Tire Applicator Foamers for applying chemical foam to wheels and tires. Unique construction and design assures perfect coverage and long life. Each set includes (2) polypropylene nozzle stands with directionally adjustable fan nozzles. Mounting plates are stainless steel construction. Available in air assist foam or airless foam units. (No pump or controls are included). Airless tire stand sets create a wet clinging foam without the need of compressed air. Simply hookup to your chemical supply pump. Air Assist Tire Stand sets use compressor air and chemical from your supply pump to create a rich, clinging foam for even better visuals and cleaning.

910005 Airless

These Foam Sticks generate streams of rich, thick foam for complete vehicle coverage. Can be used as replacements or retrofit into existing systems or for new installations. Ideal for detergents, presoaks and triple foam polishes. Sold in sets of 2 single or 2 triple assemblies. Simply supply chemical and compressed air to the arches and watch the show! All foam stick sets are 6’ in length and are adjustable for foam consistency. Prestaggered holes allow for perfect alignment and foam coverage.

910105 Air Assist

Part No.

Description

LF 910005 LF 910105

Airless Tire Foamer Set............. Air Assist Tire Foamer Set.........

910310 Triple Sticks

Net Ea.

$ 229.00 309.00

TM800 Tire Foamer System The TM800 System features the air assist Tire and Wheel Foamer set above (#910105) but is also complete with air pump, electrical panel, air switch with hose, supply tubing and delay timer. Vehicle tire activates the pump and solenoid via the air hose and switch. Timer is adjustable as needed. System is prewired and ready for installation.

910061 - Single Stick

D

Part No.

Description

LF 910061 LF 910310

Single Foam Sticks, set of 2...... Triple Foam Sticks, set of 2.......

Net Ea.

$ 248.00 825.00

D

Part No.

Description

DU TM800

Tire / Wheel Foamer System..... $ 1097.00 DULTMEIER SALES

Net Ea. OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0784


Float/Mixing Valves Hydrominder Mix Valves A HydroMinder keeps any reservoir ready with accurately mixed solution at all times. No pouring, no stirring, no waiting, no downtime. At the moment the solution level drops in the reservoir, the float ball activates a nonelectric magnetic valve. The flow of tap water through the HydroMinder siphons liquid chemical concentrate through a metering tip and automatically maintains the level of ready-to-use solution. Unit is self-contained and self-controlled. Operates using tap water only and easily installs directly on the reservoir.

• Conveyor lubrication • High pressure cleaning

Demamatic Liquid Level Proportioning Controls DEMA “Snap-acting” Mixing Valves provide automatic mixing for solution supply tanks. Allows you to have a constant chemical mixture without hand mixing. All valves are magnetically operated except the Model 436-21 which is mechanically operated. 440 Series Valves have a 3/4” FGHT or 3/8” FPT inlet port and include mounting brackets. Models 436-21 and 437-21 have a 3/4” FPT inlet port and are designed for rigid pipe plumbing (no brackets included). Operating pressure is 20 to 150 PSI. Maximum temperature is 140° F. for most accurate performance. Now standard with plastic bodies for added corrosion resistance.

Made For Jobs That Require a Constant Supply of Chemical Solution

• Automatic car and truck washing

38

Valve & Adapter are Optional

Model 440-23BT

Adjustable chain length regulates level in container

Water line

• Machine tool cooling • Systems for central cleaning

5037K Eductor

• Water treatment • Spraying systems • Metal finishing

Float opens valve when level goes down

5043A Float

• Steam Cleaning Uniquely designed, color-coded metering tips offer a wide range of accurate water-to-product concentration ratios.

Detergent Proportioned mixture feeds underwater at hose or pipe outlet which must be below bottom of float.

The Hydro-Minder may be easily installed on any liquid reservoir.

Standard Features: Buna diaphragm and plunger for tight seating • Siphon breakers to prevent back-flow of chemicals into fresh water lines, (except 440-22T) • Heavy-duty polyethylene floats • Mounting brackets on all valves (except models 436-21 and 437-21) • 8’ of Vinyl chemical tube with stainless steel foot valve.

D

Model 437-21

– FLUID VISCOSITY – If the viscosity of the fluid to be in­jected is unknown compare with the following. 1 cps: water 75 cps: SAE 10 motor oil 220 cps: SAE 30 motor oil

511 Valves

GPM Siphon Mounting Part-No. @40 PSI Breaker Bracket Inlet Dilution Net Ea. HR 515 1.5 Yes Yes 3/8” FPT 1:1 to 100:1 $ 175.50 HR 506 4.5 No Yes 3/8" FPT 4:1 to 240:1 94.95 HR 507 4.5 No No 3/8" FPT 4:1 to 240:1 89.90 HR 511 4.5 Yes Yes 3/8" FPT 4:1 to 240:1 118.00 HR 5111 5.6 Yes Yes 3/8” FPT 4:1 to 240:1 139.00 HR 532 6 * Yes Yes 3/8” FPT 3:1 to 195:1 251.50 HR 525 9 No Yes 3/4" GHT 4:1 to 530:1 185.50 HR 530 9 Yes Yes 3/4" GHT 4:1 to 530:1 245.50 HR 561 18 No Yes 3/4" GHT 7:1 to 1200:1 327.50 HR 562 18 Yes Yes 3/4" GHT 7:1 to 1200:1 347.00 HR 563 25 Yes Yes 1" FPT 8:1 to 1200:1 310.00 HR 564 25 No Yes 1" FPT 8:1 to 1025:1 283.50 HR 6655K Repair Kit for 506 & 511 Valves................................ 19.90 HR 5037K Chemical Eductor, 506/511 Valves........................... 12.35 HR 151 Dual Chemical Kit for 506 or 511 valves................... 86.95 AB 504-1204 Brass Adapter, 1/4" MPT x 3/4" FGHT..................... 4.19 AB 504-1206 Brass Adapter, 3/8" MPT x 3/4" FGHT..................... 4.25 SM 3395-301 1/4" Ball Valve........................................................... 4.95 SM 3306-304 3/4" Ball Valve........................................................... 7.22 HR 690014 Push In Tip Kit.......................................................... 10.75 HR 690015 Screw In Tip Kit......................................................... 9.65 * (2) Independent Eductors to Meter - (2) Chemicals at Different Ratios. DULTMEIER SALES

OMAHA, NE (800)

228-9666

D

Models 436-21

Part No.

GPM @ 50 PSI Dilution Range

DE 440-22T DE 440-23BT DE 440-24 DE 436-21 DE 437-21 DE 100-15K DE 100-15KU

* 4.0 4:1 to 430:1 No * 4.0 7:1 to 385:1 Yes 2.5 2:1 to 195:1 Yes 17 14:1 to 512:1 Yes * 22 10:1 to 512:1 Yes Standard Meter Tip Kit............................. Ultra-Lean Tip Kit......................................

Siphon Breaker

Net Ea.

$ 90.30 91.35 101.50 150.50 196.50 7.10 4.07

* Standard with 13 metering tips for exact dilution ration.

SERVICE & REPAIRS Did you know? We can service almost every brand of pump we sell in our catalog.

Call us at 1-800-228-9666 (Omaha, NE) for a quote! DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0028


Float Valves

39

Brass and Stainless Float Valves are ideal for control of water supply in industrial and agricultural applications. Positive acting valves feature Buna or Viton® discs and cups as noted. Buna seals are rated to 180° F. Viton® seals are rated to 450° F. Poly floats are rated to 210° F. All valves come with thumb screw and short arm but do not include float ball or float rod which must be ordered separately. Float ball size must be matched to valve size for correct operation. All valves are easily repaired and kits are shown in the charts below. Special Rotating Plunger Minimizes Disc Wear

Seal Cup

Single Lever Action

Disc Precision Machined Red Brass Casting Serrated Short Arm & Thumb Screw for Accurate Water Control

BOB Brass Float Valves

Also with Compound Lever Action

BOB Stainless Float Valves

Brass Valves Feature Heavy-Duty, Machined Red Brass Construction R400 Series Brass Valves feature MPT inlet x MPT outlet. Designed for use with R450 float rods. Buna seals are standard Rated to 125 PSI on 1/2” and 100 PSI on 1”. RC800 CASA Series Brass Valves have MPT inlet x open flow discharge. This series is designed to open and close slower than the 400 Series which reduces water hammer issues. Float rates are also higher. Designed for R450 float rods. Viton® seals are standard. Rated to 120 PSI on 1/2” and 100 PSI on 3/4” and 1”. R600 Series Brass Valves have 1-1/2” FPT inlet and outlet ports. Designed for R450 float rods and PF8-1 poly float. R440-8 copper float can be used if R434-0 adapter is also ordered. Buna seals are standard. Rated to 125 PSI. R610 Brass Valve is 2” FPT inlet x open flow. Special design can only be used with the 455-12 float rod and PF8 or R440-8 copper float ball and R209-3/8x1/8 adapter. Buna seals are standard Rated to 115 PSI.

Stainless Float Valves are AISI 316SS construction and are NSF rated for food and sanitary applications. These valves can also be used with D-Ionized, Ultra-Pure or Reverse Osmosis water as well as a wide variety of other applications. Viton® seals are standard and are rated to 450° F. R1350 & R1360 Series stainless valves have MPT or FPT inlet x FPT outlet as noted. Designed for use with R1310 float rods. Viton® seals are standard. Rated to 85 PSI. R1370 Stainless Valve is 1” FPT inlet x 3/4” FPT outlet. Designed for use with R1310 float rods. Viton® seals are standard. Rated to 85 PSI. R1380 Stainless Valves are 1-1/2” or 2” FPT inlet x FPT outlet. Designed for use with R1315 float rods and 8” stainless float ball. Viton® seals are standard. Rated to 100 PSI.

D

D

D D

R400 Float Valves (MPT Discharge)

Model R600 (FPT Discharge)

Brass Valves

Part No. RB R400-1/2 RB R400-3/4 RB RH400-3/4 RB R400-1 RB RH400-1 RB RC810-1/2 RB RC810-3/4 RB R810-1 RB R600-1-1/2 RB R610-2

Inlet 1/2" MPT 3/4” MPT * 3/4” MPT 1” MPT * 1”MPT 1/2” MPT 3/4” MPT 1” MPT 1-1/2” FPT 2” FPT

* Hybrid Brass / Plastic Design.

Outlet 1/2" MPT 3/4” MPT Open 3/4” MPT Open Open Open Open 1-1/2” FPT Open

R/RC Series (Open Discharge)

Flow Minimum @ 35 PSI Float Size 12 GPM 4” 21 GPM 5” 21 GPM 5” 43 GPM 6” 43 GPM 6” 14 GPM 4” 27 GPM 5” 80 GPM 6” 82 GPM 8” 112 GPM 8”

Model R1350

Net Ea. $ 23.50 30.50 19.95 47.50 28.50 31.30 37.35 55.95 115.50 119.50

Model R1380

D D

Model R1340 Float

Brass Valve Accessories

Part No. Description Net Ea. RB R450-6 6” Brass Float Rod for R400/R600/R800.............. $ 6.76 Stainless Valves Flow Minimum RB R450-8 8” Brass Float Rod for R400/R600/R800.............. 4.26 Part No. Inlet Outlet @ 35 PSI Float Size Net Ea. RB R450-10 10” Brass Float Rod for R400/R600/R800............ 4.51 RB R1350-1/2 1/2" FPT 1/2" FPT 37 GPM 4” $ 746.00 RB R455-12 12” Brass Float Rod for R610-2............................ 13.80 RB R1350-3/4 3/4” FPT 3/4” FPT 37 GPM 5” 761.00 RB PF21-1 4” Poly Float for 1/2” Valves.................................. 2.96 RB R1360-3/4 3/4” MPT 3/4” FPT 37 GPM 5” 761.00 GN 2P009 4” Copper Float for 1/2” Valves............................. 20.90 RB R1370-1 1” FPT 3/4” FPT 52 GPM 6” 798.00 RB PF5 5” Poly Float for 3/4” Valves.................................. 11.35 RB R440-5 5” Copper Float for 3/4” Valves............................. 32.95 RB R1380-1-1/2 1-1/2” FPT 1-1/2” FPT 112 GPM 8” 1428.00 RB PF6 6” Poly Float for 1” Valves..................................... 13.45 RB R1380-2 2” FPT 2” FPT 112 GPM 8” 1438.00 RB R440-6 6” Copper Float for 1” Valves................................ 42.95 RB PF8-1 8” Poly Float for R600-1-1/2 Valve........................ 15.85 Stainless Valve Accessories RB PF8 * 8” Poly Float for R610-2 Valve............................ 15.95 Part No. Description Net Ea. RB R440-8 * 8” Copper Float for R610-2 Valve....................... 95.95 RB R1310-8 8” Stainless Float Rod for R1350/60/70 Series.... $ 20.00 * Requires R209-3/8x1/8 Adapter for use with R455-12 Float Rod. RB R1310-10 10” Stainless Float Rod for R1350/60/70 Series.. 21.80 RB R1310-12 12” Stainless Float Rod for R1350/60/70 Series.. 28.75 Brass Valve Replacement Parts RB R1315-10 10” Stainless Float Rod for R1380 Series............ 45.80 Part No. Description Net Ea. RB R1315-12 12” Stainless Float Rod for R1380 Series............ 52.70 RB KB110 Cup & Disc Kit, R400-1/2..................................... $ 3.76 RB KB120 Cup & Disc Kit, R400-3/4..................................... 4.61 RB R1340-4 4” Stainless Float for 1/2” Valves.......................... 59.05 RB KB130 Cup & Disc Kit, R400-1........................................ 5.11 RB R1340-5 5” Stainless Float for 3/4” Valves.......................... 73.10 RB KB133 Cup & Disc Kit, RC810-1/2................................... 4.17 RB R1340-6 6” Stainless Float for 1” Valves............................. 90.55 RB KB136 Cup & Disc Kit, RC810-3/4................................... 4.91 RB R1340-8 * 8” Stainless Float for R1380 Series................... 189.00 RB KB139 Cup & Disc Kit, R810-1........................................ 3.25 * Requires R1315 Series Float Rods. RB KB140 Cup & Disc Kit, R600............................................ 6.71 RB KB150 Cup & Disc Kit, R610-2........................................ 7.08 RB KB210 Complete Plunger Kit, R400-1/2........................... 10.50 RB KB220 Complete Plunger Kit, R400-3/4........................... 14.00 RB KB230 Complete Plunger Kit, R400-1.............................. 25.80 RB KB233 Complete Plunger Kit, RC810-1/2........................ 7.97 RB KB236 Complete Plunger Kit, RC810-3/4........................ 10.65 RB KB239 Complete Plunger Kit, R810-1.............................. 21.00 RB KB240 Complete Plunger Kit, R600-1-1/2....................... 51.65 RB KB250 Complete Plunger Kit, R610-2.............................. 39.40 RB KB300 Replacement Arm Kit, R400 Series..................... 13.00 Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0966


Float Valves

40

Hydro Float Valves

Brass Float Valves

Hydro Float Valves for automatic water level control. Corrosion resistant components for maximum life. Models 502 & 503 valves are rated to 7.0 GPM at 40 psi. Model 503 does not come with mounting bracket or inlet valve and is used for in-tank mounting.

Brass 1/2" Float Valve with plastic float. Maximum flow: 4.5 GPM. Maximum temperature: 175° F. Float rod is 6.5" long. Inlet port is 1/2" FPT. Part No.

Model 572

Models 572 & 573 are rated to 44 GPM at 40 psi. Inlet is 1" FPT. Model 573 does not come with mounting bracket and is used for in-tank mounting. Part No. FPT Inlet Wt. Net Ea. HR 502 3/8" 5 lbs. $ 106.00 HR 503 3/8" 4 lbs. 79.70 HR 572 1" 6 lbs. 206.50 HR 573 1" 5 lbs. 146.50

D

ST8

Net Ea.

NP ST8 Float Valve with Float $ 13.95 NP RKST8 Repair Kit................ 4.46 NP 0300 Replacement Float. 6.53

D

Magnetically Operated Float Valves

Water Master Float Valves

Inlet

D

Outlet

Model WMC12

DEMA Magnetic, “Snap-acting” Float Valves. Now you can have the reliability of a magnetic float valve for maintaining liquid levels in tanks, drums or reservoirs. Valve is pilotoperated diaphragm style. Level differential is approximately 3". A 6" float with 9" chain is standard. Maximum operating pressure is 60 PSI. Maximum fluid temperature is 140° F.

Now a float valve designed for the rigors of Car and Truck washing. Exclusive design features two interacting valves. “Lo Valve” kicks in first when a small amount of water is needed. When valve completely opens the “Main Valve” is acti­vated. This design saves years of wear life.Valves are available in three sizes to handle a wide variety of flow requirements. Rated to 120° to 130° F.

Mounting Bracket

Model 437N

Standard Features Include: Stainless Steel internal parts • BUNA-N seals and diaphragms • Poly float. Model 440N: Inlet and outlet ports are 3/8" FPT. 3/4" FGHT adapters are included.

Construction: Brass head, neoprene di­aphragm and stainless steel seat are corrosion-resistant and virtually maintenance-free. Complete with 6” float rod and plastic float that is 3-1/2” long x 1-3/4” diameter. Part No.

D

Model 437N: 3/4" FPT inlet and outlet ports. Part No.

Flow Rate Mounting @ 50 PSI Bracket Net Ea.

DE 440N 6 GPM DE 437N 64 GPM DE 440NX 6 GPM DE 437PNX 64 GPM

Yes Yes No No

$ 70.70 116.50 59.40 105.00

Inlet Port Outlet Port Flow @ 40 PSI Net Ea.

WQ WMC12 1/2" MPT 1/2" MPT 9 GPM $ 40.95 WQ WMC34 3/4" MPT 1/2' MPT 12 GPM 41.85 WQ WM1H 1" MPT 3/4" MPT 58 GPM 65.95 WQ WM004S Diaphragm for 1/2” & 3/4” Valves......... 7.92 WQ WMS0041 Diaphragm for 1” Valves ...................... 12.55

Float Valves High capacity float valves for maintaining liquid level in tanks, drums, or similar reservoirs. • Adjustable for Desired Levels • Plastic Bodies

Water Valves

• Stainless Steel Lever Parts

D

Ideal for use in car/truck wash holding tanks, fountains, livestock tanks and many more.

• Buna-N Rubber Parts • Polyethylene Float Standard

Hudson Water Valves will solve your fluid control problems once and for all. Unique design uses fluid pressure as opposed to lever arms or float balls. Features: Valve body is made of durable, glass-filled nylon • Internal parts are stainless, silicone and plastic for rust-free performance • Meets antisiphon requirement when properly installed • No levers, arms or external moving parts • Rated 90° or 150° F. as shown • 1/2” Valves are rated to 65 PSI • 1” Valves are rated to 100 PSI.

DEMA High Capacity Float Valves are designed to maintain a liquid level in a tank or similar reservoir. Valves are pilot operated diaphragm type, and are adjustable for desired liquid levels. Plastic bodies, Stainless Steel lever parts, Buna-N rubber seats, seals, and diaphragms. Polyethylene float is standard. Polypropylene float is available for high-temperature duty. MODEL 436N: High Capacity Float Valves are generally mounted on a rigid water supply pipe.

1/2” Valve

1” Valve

Connections

CV

Capacity - GPM

MODEL PORT Flow 1 2 5 10 20 Maximum Part No. Inlet Flow @ 40 PSI Temperature

HD V1200 HD V1200HT HD V1000 HD V1000HT

1/2" 1/2” 1” 1”

17 GPM 17 GPM 55 GPM 55 GPM

DULTMEIER SALES

90° F. 150° F. 90° F. 150° F. OMAHA, NE (800)

Net Ea.

$ 25.75 28.95 25.75 28.95

228-9666

Number Inlet Outlet DIA. Factor PSI PSI PSI PSI PSI 3/4" FPT 3/4"FPT 436N pipe pipe 3/4" 9.0 5.4 11 20 28 40

DAVENPORT, IA (800)

553-6975

Part No.

Net Ea.

DE 436N High Capacity

$ 76.50

www.dultmeier.com

E0027


Float Valves

41

Heavy-duty, corrosion-resistant float valves for car wash, truck wash, livestock watering, cisterns, process applications and water storage tanks. Unique design allows for valves to be top mounted, bottom mounted or side wall mounted. All accessories are included for rigid or flexible mounting of floats depending on valve series. Some valves have freeze prevention options for outdoor use. Simple, yet reliable mechanical design. A wide variety of styles and sizes to meet almost any water supply requirement. Slow shut-off design greatly reduces water hammer. All valves are “Full Flow”, no restrictors.

For Rojo, Topaz, & Vortex Valves

RJ Rojo Series

MF MegaFlow Series

RJ ROJO Series low flow valves can be mounted above or below the water level. RJ15 and RJ20 valves are rated from 3-1/2 to 4 GPM. 0 to 150 PSI. RJ20HF is rated to 7 GPM at up to 75 PSI. All valves in this series can be top, bottom or side mounted. Adjustable angle rod, float, wall bung adapter and flexible float line are included. Rated to 115° F.

MF MegaFlow Series high flow valves are designed for use in livestock watering troughs and are for underwater mounting only. Can be side or bottom mount. Flexible float line protects valve and float against damage. Rated to 65 GPM and up to 150 PSI. Standard with valve, float and flexible line.Temperatures to 115° F. For indoor or outdoor use.

D

Flow Maximum Part No. Inlet Size @ 75 PSI Temperature JO RJV15 1/2” MPT 3.5 GPM 115° F. JO RJV20 3/4” MPT 3.5 GPM 115° F. JO RJV20HF 3/4” MPT 6.8 GPM 115° F.

D

Net Ea. $ 24.95 24.95 25.95

TP Topaz Series TP Topaz Series high flow valves can be mounted above or below the water level. A good choice where higher flow rates are required. Rated up to 80 GPM. 5 to 100 PSI. All valves in this series can be top, bottom or side mounted. Adjustable angle rod, float, wall bung adapter, flexible float line and top port for freeze prevention kit are included. Rated to either 115° F. Regular Series or 176° F. Industro Series as shown. For indoor or outdoor use.

D

Adjustable Arm

Flow Maximum Part No. Inlet Size @ 75 PSI Temperature JO TPV20DLT 3/4” 55 GPM 115° F. JO TPV1D 1” 80 GPM 115° F. JO TPVI20 * 3/4” 55 GPM 176° F. JO TPVI1 * 1” 80 GPM 176° F. JO FPV Freeze Prevention Kit............................ * Industro Series.

VX Vortex Series

Net Ea. $ 59.50 58.75 156.50 159.50 11.95

Flow Maximum Part No. Inlet Size @ 65 PSI Temperature JO MFV20DLT 3/4” 65 GPM 115° F. JO MFV1D 1” 80 GPM 115° F.

Float Valves

Net Ea. $ 39.95 40.65

Megaflow Series

RJ Series

D

Adjustable Arm

VX Vortex Series valves are designed for above water horizontal or vertical mounting. A good choice where maximum flow rates are required. Rated up to 160 GPM. 5 to 100 PSI. Adjustable angle rod, float, top port for freeze prevention kit and manual lock off switch are standard. Rated to 140° F. For indoor or outdoor use.

D

Vortex & Topaz Series

Flow Maximum Part No. Inlet Size @ 35 PSI Temperature Net Ea. JO VXV112 1-1/2” 160 GPM 140° F. $ 208.00 JO VXV2 2” 160 GPM 140° F. 209.50 JO FPV Freeze Prevention Kit............................ 11.95 DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0993


Float Valves • Level Indicator

42

Jobe Diferential Float Valves These unique valves are designed to maintain water levels in storage tanks, cisterns or irrigation applications. Eliminates constant stop/start of pumps or water systems. As tanks empty, the weighted float travels down the cord until it hits the bottom stop, the valve then opens giving in full water flow. Float rises to top stop and shuts off valve as water level rises. Features:

• Corrosion-Resistant Materials • High Flow Rates • Adjustable Stop & Start Levels • Reduces Pump Operation • Fits Almost Any Type of Tank • Rated from 15 to 150 PSI

Maximum Part No. Inlet Flow Net Ea. JO TPVD20DLT 3/4” MPT 55 GPM $ 170.00 JO TPVD1DLT 1” MPT 75 GPM 175.00 JO VXVD112 1-1/2” MPT 140 GPM 219.00 JO VXVD2 2” MPT 140 GPM 225.00

Jobe Water Level Indicator Simple Float and Rod System that shows water level in enclosed or covered tanks. Highly visible indicator. Double bracing arms and mounting bracket are included. Stainless steel and plastic construction. Overall assembled size is 7’2” (breaks down for shipping).

Part No. Net Ea. JO LIV Water Level Indicator....... $ 129.50

FPV Freeze Prevention Kit

PMV Valve Cover

FPV Freeze Prevention Kit. For outdoor water applications. Mounts to special top port fitting on the Topaz and Vortex Series Valves. When temperatures approach freezing, cap valve is manually turned to allow a low flow of water to continually pass through the valve. Best used when temperatures will rise above freezing for a few hours each day. Output of up to 5 gallons per hour.

PMV Valve Cover is designed for use with Rojo or Topaz Series. Valves mount to bottom portion of cover which then attaches to tank or trough. Top portion attaches to bottom section enclosing and protecting valve from livestock. Robust and durable, UV protected. Dimensions are 7” wide x 16” long x 6-3/4” high.

D

Part No. Net Ea. Part No. Net Ea. JO PMV Valve Cover / Protector.......... $ 51.95 JO FPV Freeze Prevention Kit............ $ 11.95

DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E1047


Eductors • Mixer • Heaters

43

PENBERTHY

Immersion Heaters

Tank Mixing Eductors

— Commercial / Industrial Grade —

Designed to allow small pumps to circulate or agitate solutions in open or enclosed tanks. Keeps solutions in continuous motion and prevents “settling out” of liquids in storage. In many cases they also produce a mixing action that cannot be duplicated using mechanical methods.

Immersed Length

Standard in polypropy­lene or cast iron con­ struc­ tion. (Stainless is also avail­able.) Large tanks of any shape may require multiple units to main­tain agitation in all parts of the tank. Maximum pres­ sure is 100 psi. Maximum tem­pera­ture is 220° F.

D

TME-112

Screw Plug Style

D

MPT Threads

Dimensions Materials: • 316 Stainless Steel (B3) • Carbon (tool) Steel (A2) • Polypropylene (D6)

Code RF Flow rate (gpm) D D1 L WS UPD0075xxSN 3/4" 16 23 28 32 36 13/16" 2-3/4" 5-3/4" 15/16" UPD0150xxSN 1-1/2" 37 53 64 74 83 2-3/8" 4-1/4" 9" 2-3/8" UPD0200xxSN 2" 66 93 114 135 147 3" 4-1/2" 13" 2-3/4" UPD0300xxSN 3" 150 213 262 302 338 3-1/2" 7-1/2" 17-1/2" 3-3/4" Pressure (psi) 15 30 45 60 75

One gallon motive Nozzle

Diffuser

Part No. DU TME-34 DU TME-112 DU CTE-112 DU CTE-2 DU CTE-3

Inlet Port Construction Net Ea. 3/4" MPT Poly $ 30.56 1-1/2" MPT Poly 76.08 1-1/2" FPT Cast Iron 139.51 2" FPT Cast Iron 340.05 3" FPT Cast Iron 547.74

Screw Plug Immersion Heaters are ideal for direct heating of solutions and oils in holding tanks. Sheath materials are available in Steel, Copper and Incoloy. All heaters are standard with thermowells and remote thermostats. Standard with (NEMA 1) terminal enclosures with knockouts for ease of wiring. (NEMA 4 enclosures for flammable materials or wet environments also available). Voltage ratings are single phase, 120 volt or 120/240 volt as shown. (3-Phase available in some models). UL® and CSA rated. All models are standard with MPT threads to fit existing FPT couplings or flanges on existing tanks.

HEATER CONSTRUCTION: Copper, Sheath, Brass Plug: Best Choice for Clean Water or liquids not corrosive to copper. Rated to 350° F.

Steel Sheath, Steel Plug:

Best choice for Lightweight oils, degreasing solutions and other non- corrosive solutions. Rated to 750° F.

Incoloy® Sheath, 304SS Plug: Best choice for caustic solutions,

Four gallons suction

5 gallons circulated

Tank Mixing Eductors Operate Simply & Efficiently

Vertical Mounting Top View

Liquid Drum Mixer Liquid Mixers for blending, mixing, suspending or dissolving liquids and powders into solutions. Mixing is done directly in tanks, drums or holding containers. Standard Features: Impellers and Shafts are 304 Stainless Steel Construction • Motors are Open-Dripproof (Open).

degreasing solutions, process water & water with cleaning agents. Rated to 1600° F.

MPT Overall Immersed Part-No. Plug Sheath Watts Volts Length Length Net Ea. JS 6BC-S2 1" Incoloy 1000 120 10-1/2" 6-5/8" $ 249.00 JS 12BC-S2 1" Incoloy 2000 120 16-3/8" 12-1/2" 325.50 JS 16BC-S2 1" Steel 1000 120 20-5/8" 16-3/4" 196.50 JS 18BC-S2 1" Incoloy 2000 120 16-3/8" 12-1/2" 289.00 JS 4BE-S2 1-1/4" Copper 1000 120/240 8-1/4" 4-3/8" 327.00 JS 8BE-S2 1-1/4" Copper 2000 120/240 12-7/16" 8-1/2" 333.00 JS 12BE-S2 1-1/4" Steel 1000 120/240 16-11/16" 12-3/4" 344.00 JS 25BE-S2 1-1/4" Steel 2000 120/240 29-5/16" 25-3/8" 375.00 JS 24BN-S2 1-1/4" Incoloy 2000 120/240 28-5/16" 24-3/8" 418.00 JS 78BG-S2 2" Copper 2000 120-240 12-7/16" 8-1/8" 404.00 JS 71BG-S2 2" Copper 3000 120/240 15-7/16" 11-1/8" 412.00 JS 77BG-S2 2" Steel 2000 120/240 21-13/16" 17-1/2" 438.50 JS 75BG-S2 2" Steel 3000 120/240 29-5/16" 25" 449.50 JS 17BH-S2 2" Incoloy 3000 120 22" 17-3/4" 629.00 JS 25BH-S2 2" Incoloy 4500 120 29-1/2" 25-1/4" 679.00

D

A05DS

Part No. Mount Motor BL AO5DS Drum 1/4 HP Open DULTMEIER SALES

Shaft 1/2" x 28"

Call Us For All Your Car Wash & Truck Wash Needs!

Wt. Net Ea. 26 lbs. $ 249.50

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0026


PowerBlanket Heaters

44

Heaters Industrial heating solutions for drums, Pails, totes, pipe, valves, tanks, hose and cylinders. Cold weather protection, designed for thaw or freeze prevention and viscosity control. Available with or without thermostatic controllers. Provides uniform direction heating for temperature sensitive materials and equipment. Features: Easy-to-Install and remove • Insulated, full-wrap design • Can be used on both metals and plastics • Uniform heating means no hot or cold spots • Safely heat without scorching • Various temperature settings • Low energy consumption • UL/CSA/ETL compliant • Tough design is water and weather-resistant. Drum/Pail Models with thermostats are rated to 160° F. Models shown without thermostats are designed for fixed 100° F. output. Pipe/Valve heater blankets are rated to -10° F. and do not include thermostats.

• INSULATE IT

• HEAT IT

• WRAP IT

• THAW IT

• PROTECT IT

• CURE IT

All Power Blankets are rated for 120 Volt, AC and come with 6’ power cords. (Curing, thawing and snowmelt blankets are also available, pricing on request).

D D

BH55PRO

TH330 Tote Heater

BH30RR

Cylinder Blankets Also Available

D

Drum/Pail/Tote Blanket Heaters

Pipe/Valve Blanket Heaters

Part No. Container Size Thermostat Amp Rating PE BH05RR 5 Gallon No .50/1.00 PE BH05PRO 5 Gallon Yes 1.33 PE BH15RR 15 Gallon No 1.33/2.67 PE BH15PRO 15 Gallon Yes 3.33 PE BH30RR 30 Gallon No 2.33/4.67 PE BH30PRO 30 Gallon Yes 6.00 PE BH55RR 55 Gallon No 3.33/6.67 PE BH55PRO 55 Gallon Yes 8.00 PE TH275 275 Gallon Yes 12.00 PE TH330 330 Gallon Yes 12.00

Wt. Net Ea. 4 lbs. $ 260.00 6 lbs. 450.00 7 lbs. 350.00 9 lbs. 595.00 9 lbs. 425.00 11 lbs. 680.00 11 lbs. 495.00 13 lbs. 725.00 41 lbs. 1575.00 45 lbs. 1680.00

Part No. Pipe Size Length Amp Rating Net Ea. PE PH040505 4” - 5” 5” 1.33/2.67 $ 560.00 PE PH040510 4” - 5” 10” 3.0/6.0 870.00 PE PH040520 4” - 5” 20” 6.0/12.0 1370.00 PE PH060605 6” 5” 2.33/4.67 645.00 PE PH060610 6” 10” 4.58/9.17 998.00 PE PH060620 6” 20” 8.0/16.0 1480.00 PE PH080805 8” 5” 3.0/6.0 730.00 PE PH080810 8” 10” 6.0/12.0 1250.00 PE PH080820 8” 20” 12.0/24.0 1980.00 Note: Blankets for 10” & 12” Pipe Also Available on Request.

We now have our Catalogs as well as Parts Schematics online!

Visit Our Online Store Anytime. Anywhere. dultmeier.com

www.dultmeier.com DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0958


PLUNGER PUMPS

45

Low Flow Models (3 to 6 GPM) CAT PUMPS® TRIPLEX PLUNGER PUMPS are designed to deliver smooth, low pulsation flows at a wide variety of pressures and flow rates. Widely used in continuous-duty, high pressure applications including Car/Truck Wash, Industrial Cleaning, Pressure Washing, Reverse Osmosis, Water Misting and many more. CAT PUMPS® are the “Pumps with Nine Lives”. Standard Features Include: High pressure seals that are lubricated and cooled by the solution being pumped • Oil-bath crankcase • Heat treated valves and seats • Forged brass or stainless steel manifolds • Solid ceramic plungers • Exclusive high pressure seal design • Rated from 140° to 160° F. depending on the model. Seal options up to 180° F. available • Wet ends can be serviced without entering the crankcase • Pumps are rated to 50 micron particles and 5-9 ph. Note: Mounting rails and mounting kits are not included and must be ordered separately). Low Flow Pumps are rated from 3 to 6 GPM. See following page for high flow models.

D

D

D

340 & 350

1530

3CP

530 & 550

D

D

D

D

D

240 & 270

310

57

Pump No. GPM PSI RPM CC 230 2.3

1500 1725 CC 240 3.6 1200 1725 CC 270 4.2/3.5 1000/1500 1725/1420 CC 3CP1140 3.6 2200 1725 CC 3CP1140.3400† 3.6 2200 1725 CC 5CP3110CSS 3.6 3500 1750 CC 310 4.0 2200 950 CC 310B†† 4.0 2200 950 CC 310S** 4.0 2200 950 CC 340 4.0 1800 1725 CC 340B†† 4.0 1800 1725 CC 5CP2120W 4.0 2500 950 CC 5CP2120B†† 4.0 2500 950 CC 5CP2140W 4.0 2500 1750 CC 5CP2140B†† 4.0 2500 1750 CC 3CP1120 4.2 2200 1725 CC 3CP1120.3400† 4.2 2200 1725 CC 5CP3160 4.2 3500 1750 CC 5CP3160CSS 4.3 3500 1750 CC 45 4.5 3500 1645 CC 57 4.5 4000 1285 CC 700 4.5 5000 1750 CC 5CP3120 4.8 3000 1750 CC 5CP3120.3400† 4.8 3000 1750 CC 350 5.0 1500 1725 CC 5CP2150W 5.0 2000 1725 CC 530 5.0 2500 1100 CC 550 5.0 3000 1415 CC 5CP5120 5.0 3000 1415 CC 5CP5120.3400† 5.0 3000 1415 CC 5CP5140 5.5 3500 1500 CC 56 5.5 3500 1210 CC 5CP6120 7.5/6.0 1200/1600 1750/1400

Inlet

Outlet

Shaft

Wt.

1/2" 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2”

3/8" 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8”

16.5mm 16.5mm 16.5mm 16.5mm 16.5mm 20mm 20mm 20mm 20mm 20mm 20mm 20mm 20mm 20mm 20mm 16.5mm 16.5mm 20mm 20mm 20mm 24mm 24mm 20mm 20mm 20mm 20mm 24mm 24mm 20mm 20mm 20mm 20mm 20mm

13 lbs. 13 lbs. 15 lbs. 15 lbs. 15 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs.

5CP2120 & 2140 Mounting Kit

*30612 *30612 30651*30612 *30612 *30612 *30612 30659*30611 30659*30611 30659*30611 *30611 *30611 30659*30611 30659*30611 *30611 *30611 *30612 *30612 *30612 *30612 *30611 30660*30611 *30611 *30612 *30612 *30611 *30611 30660*30611 30660*30611 30659*30611 30659*30611 30659*30611 30660*30611 30660*30611

* Mounting Rails Only. ** Features Stainless Steel Sleeves in Manifold. † Rated to 200° F., Run Dry Feature. †† Manifold features Lifetime Warranty against washout.

OPTIONAL MOUNTING KIT COMPONENTS

Call Toll-Free for Prices !

30651 Includes 30612 mounting rails, 30246 pulley (5" diameter) & key and a 25130 shaft protector cover. Current 30659 Includes 30611 mounting rails, a 30633 pulley (8" diameter) and a 118672 shaft protector cover. 30660 Includes 30611 mounting rails, 30206 pulley (9.75" diameter), 43256 shaft protector cover, 33000 hub (24mm) and a 30067 key. DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0030


PLUNGER PUMPS

46

High Flow Models (7 to 75 GPM) CAT PUMPS® TRIPLEX PLUNGER PUMPS are designed to deliver smooth, low pulsation flows at a wide variety of pressures and flow rates. Widely used in continuous-duty, high pressure applications including Car/Truck Wash, Industrial Cleaning, Pressure Washing, Reverse Osmosis, Water Misting and many more. CAT PUMPS® are the “Pumps with Nine Lives”. Standard Features include: High pressure seals that are lubricated and cooled by the solution being pumped • Oil-bath crankcase • Heat treated valves and seats • Forged brass or stainless steel manifolds • Solid ceramic plungers • Exclusive high pressure seal design • Rated from 140° to 160° F. depending on the model. Seal options up to 180° F. available • Wet ends can be serviced without entering the crankcase • Pumps are rated to 50 micron particles and 5-9 ph. Note: Mounting rails are not included and must be ordered separately except for 67 and 68 Series). High Flow Pumps are rated from 7 to 75 GPM. See following page for low flow models.

D

D D

1050

D

1530 Pump No. GPM PSI RPM

Inlet

Outlet

Shaft

Wt.

Mounting Rails

CC 650 7

3000

1000

3/4"

1/2"

30mm

44 lbs.

30613

CC 1560 8

4000

1140

1”

3/4”

30mm

43 lbs.

30613

CC 3801** 9

5000

825

1-1/2”

1”

35mm

170 lbs.

92674

CC 5CP6190 9.7

1200

1750

1/2”

3/8”

20mm

20 lbs.

30611

CC 7CP6170 12

1800

1600

3/4”

3/8”

24mm

30 lbs.

30613

CC 6810 10

10,000

600

1”

1/2”

45mm

377 lbs.

126604

2000

1750

1/2”

1/2”

24mm

40 lbs.

30613

3/4”

1/2”

30mm

44 lbs.

30613

CC 7CP6110.3400† 10.5 CC 1050 12/10

2530

1800/2200 1150/960

3535

CC 660 10

3000

1430

3/4”

1/2”

30mm

44 lbs.

30613

CC 660.3400† 10

3000

1430

3/4”

1/2”

30mm

44 lbs.

30613

CC 3507 10

5000

915

1-1/2”

3/4”

35mm

152 lbs.

92674

CC 1051** 12

1800

1150

3/4”

1/2”

30mm

44 lbs.

30613

CC 3811** 14

3000

800

1-1/2”

1”

35mm

170 lbs.

92674

CC 1530 15.5

1500

1450

1”

3/4”

30mm

55 lbs.

30613

CC 6801** 15

7000

600

2”

1-1/4”

45mm

335 lbs.

Included

CC 1540E 18

1200

1100

1”

1-1/4”

45mm

43 lbs.

30613

CC 2510 20

2000

1450

1-1/4”

3/4”

30mm

79 lbs.

30614

CC 3560 20

4000

1160

1-1/2”

1”

35mm

139 lbs.

92674

CC 3520 23

2000

800

1-1/2”

1”

35mm

139 lbs.

92674

CC 3521** 23

2000

800

1-1/2”

1”

35mm

139 lbs.

92674

CC 2530 25/21 1000/1200 1150/960

1-1/4”

3/4”

30mm

79 lbs.

30614

CC 3535 36

1200

800

1-1/2”

1”

35mm

139 lbs.

92674

CC 3531** 36

1200

800

1-1/2”

1”

35mm

139 lbs.

92674

CC 6831** 40

2300

625

2”

1-1/4”

45mm

335 lbs.

Included

CC 3545 45

1000

765

1-1/2”

1”

35mm

139 lbs.

92674

CC 6841** 48

2000

615

2”

1-1/4”

45mm

335 lbs.

Included

CC 6760 60

1200

520

2”

1-1/4”

45mm

335 lbs.

Included

CC 6775 75

1200

650

2”

1-1/4”

45mm

335 lbs.

Included

** Features Stainless Steel Manifolds. † Rated to 200° F., Run Dry Feature.

OPTIONAL MOUNTING KIT COMPONENTS

Call Toll-Free for Current Prices !

30651 Includes 30612 mounting rails, 30246 pulley (5" diameter) & key and a 25130 shaft protector cover. 30659 Includes 30611 mounting rails, a 30633 pulley (8" diameter) and a 118672 shaft protector cover. 30660 Includes 30611 mounting rails, 30206 pulley (9.75" diameter), 43256 shaft protector cover, 33000 hub (24mm) and a 30067 key.

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0912


PUMPS

47 GEAR REDUCTION PLUNGER PUMPS

“SuperFlow” Plunger Pumps

D D

D

2SF

Direct Drive Plunger Pumps from Cat Pumps®. Designed to run at direct electric motor or gas engine speeds. Pumps feature hollow shafts, mounting flange and pressure unloader valve. Ports are 1/2” inlet x 3/8” outlet.

SLOWER PUMP RPM FOR LONGER PUMP LIFE . . . Gear Reduction Pump Units are designed to mount-up directly to gasoline engines. Eliminates the need for belts, pulleys and belt guards. Gearbox design allows pumps to run at slower RPM. All pumps shown are “Triplex Plunger” design. These pumps feature ceramic plungers for long life and abrasion resistance. Triplex design provides low pulsation and quiet operation. Internally lubricated and cooled packings for extended life. The gearbox on each unit features hardened steel gears for smooth, quiet operation. Totally sealed housing provides independent gearbox lubrication. Engine Part No. GPM PSI Required CC 3CP1120G 3.5 2200 7-10 HP, 3/4” Shaft CC 5CP3120G1 4.5 3500 10-13 HP, 1” Shaft CC 700G1 4.5 5000 20-24 HP, 1” Shaft CC 5CP5140G1 5.5 3500 15-18 HP, 1” Shaft CC 5CP6120G1 6.7 1600 10-13 HP, 1” Shaft CC 56G1 8.0 1800 13-15 HP, 1” Shaft CC 5CP6190G1 8.7 1200 10-13 HP, 1” Shaft CC 7CP6110G1 10 2000 18-21 HP, 1” Shaft

Wt. 22 lbs. 27 lbs. 44 lbs. 27 lbs. 26 lbs. 37 lbs. 27 lbs. 39 lbs.

Call Toll Free for Pricing

D

Clutches shown are priced less the pump

These Clutches work with flow switches or pressure switches to control operation of pumps. 12-Volt DC rating. High quality bearings, rotors and hubs for added life.

Fits Part No. Grooves Shaft Diameter Pump Models CC 34961 1 16.5 mm 7” 3FR/3PFR/4FR CC 34964 2 16.5 mm 7” 3FR/3PFR/4FR CC 34960 1 216.5 mm1 7” 3CP CC 34965 2 16.5 mm 7” 3CP CC 34962 1 220.0 mm1 7” 5FR/5FPR CC 34963 2 20.0 mm 7” 5FR/5FPR CC 34970 1 220.0 mm1 7” 5CP CC 34980 2 20.0 mm 7” 5CP CC 76970 2 20.0 mm 10” 5CP CC 34628 1 224.0 mm1 12-3/4” 7FPR CC 34630 2 224.0 mm1 12-3/4” 7FPR CC 34563 2 30.0 mm 12-3/4” 15FPR

Wt. 9 lbs. 9 lbs. Call 9 lbs. Toll 9 lbs. Free 9 lbs. for 9 lbs. Current 9 lbs. Pricing! 9 lbs. 14 lbs. 18 lbs. 23 lbs. 22 lbs.

4SF Series are rated to 3500 PSI and flow to 5 GPM. Designed for electric motor or gas engine drive at the RPM shown. Rated to 160° F. For Electric Motors Part No. GPM CC 2SF22ELS 2.2 CC 2SF29ELS 2.8 CC 2SF20ES 2.0 CC 2SFX20ES 2.0 CC 2SF22ES 2.2 CC 2SFX22ES 2.2 CC 2SF30ES 3.0 CC 2SFX30ES 3.0 CC 2SF30GES 3.0 CC 2SFX30GES 3.0 CC 4SF40ELS 4.0 CC 4SF45ELS 4.5 CC 4SF50ELS 5.0

PSI 2000 1500 2000 2000 2000 2000 1500 1500 2000 2000 3500 3000 3000

RPM 1750 1750 3450 3450 3450 3450 3450 3450 3450 3450 1725 1725 1725

PSI 2000 2000 2000 2000 3500 3500 3000 3000

RPM 3450 3450 3450 3450 3450 3450 3450 3450

Drive Shaft Electric 5/8" Electric 5/8” Electric 5/8” Electric 5/8” Electric 5/8” Electric 5/8” Electric 5/8” Electric 5/8” Electric 3/4” Electric 3/4” Electric 1-1/8” Electric 1-1/8” Electric 1-1/8”

Wt. 11 lbs. 11 lbs. 11 lbs. 11 lbs. 11 lbs. 11 lbs. 11 lbs. 11 lbs. 11 lbs. 11 lbs. 24 lbs. 24 lbs. 24 lbs.

Call Toll Free for Pricing

Part No. GPM CC 2SF30GS 3.0 CC 2SF35GS 3.5 CC 2SFX30GS 3.0 CC 2SFX35GS 3.5 CC 4SF35GS1 3.5 CC 4SF40GS1 4.0 CC 4SF45GS1 4.5 CC 4SF50GS1 5.0

Drive Gas Gas Gas Gas Gas Gas Gas Gas

Shaft 3/4" 3/4” 3/4” 3/4” 1” 1” 1” 1”

Wt. 11 lbs. 11 lbs. 11 lbs. 11 lbs. 24 lbs. 24 lbs. 24 lbs. 24 lbs.

Call Toll Free for Pricing

“DX” PLUNGER PUMPS Generation Direct Drive Plunger Pumps from Cat Pumps®. Ideal for pressure washing applications. Designed to run at direct electric motor or gas engine speeds. All pumps include flange, pressure unloader and chemical injector. Rated to 140° F. Ports are 1/2” inlet x 3/8” outlet.

For Electric Motors Part No. CC 2DX20ES

GPM 2.0

PSI RPM 2000 3450

Drive Electric

Shaft 5/8"

Wt. Net Ea. 11 lbs. $ 345.50

Drive Gas Gas Gas Gas Gas Gas Gas Gas Gas

Shaft 3/4" 3/4” 3/4” 3/4” 3/4” 1” 1” 1” 1”

Wt. Net Ea. 11 lbs. $ 365.00 11 lbs. 365.00 11 lbs. 365.00 11 lbs. 365.00 11 lbs. 409.00 11 lbs. 409.00 26 lbs. 614.00 26 lbs. 615.00 26 lbs. 619.00

For Gas Engines

SERVICE & REPAIRS

Part No. CC 3DNX25GSI CC 3DNX27GSI CC 3DX30GSI CC 3DX29GSI CC 3SPX35GEI CC 3SPX30G1I CC 66DX30G1I CC 66DX35G1I CC 66DX40G1I

Did you know? We can service almost every brand of pump we sell in our catalog. Call us at 1-800-228-9666 (Omaha, NE) for a quote!

DULTMEIER SALES • OMAHA, NE

2SF Series are rated to 2000 PSI and 3.0 GPM. Designed for electric motor or gas engine drive at the RPM shown. 2SFX Pumps are the same as 2SF but with newly designed flanges and comes with a bypass hose. Both series are rated to 160° F. with seal options up to 190° F.

For Gas Engines

12-VOLT CLUTCHES

4SF

(800) 228-9666

www.dultmeier.com

GPM 2.5 2.7 3.0 3.1 3.5 3.0 3.0 3.5 4.0

PSI 2800 2800 2500 2000 2500 3000 4000 4000 4000

• DAVENPORT, IA

RPM 3450 3450 3450 3450 3450 3450 3450 3450 3450

(800) 553-6975

E0032


Motor/Pump Units

48

BD Series Close-Coupled Pump & Motor Units

Direct Drive Pump/Motor Units — Long Coupled Design —

Direct-Drive Pump & Motor Units featuring CAT Pumps® or Hypro plunger pumps close-coupled to Baldor C-Face motors. High quality, economical components in a compact, space saving design!! Eliminates the need for cumbersome belts, guards and pulleys. All Pumps Feature: Triplex plunger design • Bronze or Chrome-plated bronze manifolds for corrosion resistance • Polished ceramic plungers for longer service life • Unitized valves • Lubricated packing design cooled by pumped liquid for longer seal life. All motors are Totally Enclosed, Fan Cooled. Single phase motors are standard with Capacitor Start feature. Three phase motors are 230/460 volt. Single phase motors are 115/230 volts.

Close-Coupled Pump and Motor units from CAT Pumps® eliminate cumbersome belts and pulleys as well as clumsy belt guards. Directdrive design allows pumps to run at a faster RPM which smooths pump discharge so that a pulsation device is not necessary. Pumps are standard with Baldor motors.

No. 240BD31

D

D

Model 240C33C (Long Coupled) Specifications: Inlet ports on all pumps are 1/2" FPT. Outlet ports on all pumps are 3/8" FPT. Maximum operating temperature is 180° F. on Hypro and 160° F. on CAT Pumps®. Maximum operating RPM is 1725. Maximum inlet pressure is 60 PSI on Cat pumps.

Pump & Motor Combinations Maximum Wt. Part No. Pump Model GPM PSI HP Phase Lbs.

Net Ea.

DU 240C31C Cat 3CP 3.6 1200 3 1 125 $ 1564.00 DU 240C33C Cat 3CP 3.6 1200 3 3 120 1233.00 DU 233C31H Hypro 2330 3.1 1500 3 1 125 1364.00 DU 233C33H Hypro 2330 3.1 1500 3 3 120 1100.00 DU 340C31C Cat 5CP 4.0 1100 3 1 135 1692.00 DU 340C33C Cat 5CP 4.0 1100 3 3 110 1367.00 DU 234C31H Hypro 2340 4.3 1000 3 1 135 1363.00 DU 234C33H Hypro 2340 4.3 1000 3 3 115 1100.00 DU 340C51C Cat 5CP 4.0 1800 5 1 115 1683.00 DU 340C53C Cat 5CP 4.0 1800 5 3 115 1384.00 Giant Pump/Motor Combinations also available !

All units feature CAT Pumps® Ceramic Plunger Pumps. Motors are “American Made” 3-HP Totally Enclosed, Fan Cooled, 230 Volt Single Phase or 208/230/460 Volt three Phase, 1725 RPM. Single Phase motors are capacitor start.

240/270/3CP SERIES PUMP & MOTOR UNITS Part No. PSI @ GPM ELECTRIC MOTOR

Wt. Lbs

CC 240BD31 CC 240BD33 CC 270BD31 CC 270BD33 CC 3CP1120BD31 CC 3CP1120BD33

127 125 127 125 127 125

1200 1200 1000 1000 1000 1000

3.6 3.6 4.2 4.2 4.2 4.2

3 HP-Single Phase 3 HP-Three Phase 3 HP-Single Phase 3 HP-Three Phase 3 HP-Single Phase 3 HP-Three Phase

Call Toll Free For Prices

340/350/5CP Series Pump Motor Units Short Coupled Design

Oil Drain Kit For CAT PUMPS Easily change pump oil when needed with CAT Oil Drain Kits. Designed to be mounted to flat surface or panel mounted. Kits include hose, angle plate, panel nut, plug and o-ring.

D

D

34334 Kits fit all piston pumps up to 60FR series and plunger pumps up to 35FR series. Does not fit 2SF, 2DX, 2SFX , 3DNX, 3DX, 3SP and 4DNX.

All units feature the CAT Pumps® Ceramic Plunger Pumps. Baldor Motors in 3 or 5 HP versions are Totally Enclosed, Fan Cooled, 1725 RPM, 230 Volt Single Phase or 208/230/460 Volt three Phase. Single Phase motors are capacitor start. Short coupled, compact design.

No. 34334

990394 Kits fit 2DX, 2SF, 2SFX, 3DNX, 3DX, 3SP, 3SPX, 4DNX and 4SF pumps.

PUMP & MOTOR UNITS Part No. PSI @ GPM ELECTRIC MOTOR CC 340BD31 1100 4 3 HP-Single Phase CC 340BD33 1100 4 3 HP-Three Phase CC 340BD51 1800 4 5 HP-Single Phase CC 340BD53 1800 4 5 HP-Three Phase CC 350BD51 1450 5 5 HP-Single Phase CC 350BD53 1450 5 5 HP-Three Phase CC 5CP2140BD51 2000 4 5 HP-Single Phase CC 5CP2140BD53 2000 4 5 HP-Three Phase

34314 Kits fit piston pumps 6020 through 6041, plunger pumps 3501 through 3560, 3801 through 3841K, 6747 through 6777 and 6801 through 6861K. Part No.

CC 34334 CC 990394 CC 34314

Net Ea.

Oil Drain Kit for Pumps Shown Above Oil Drain Kit for Pumps Shown Above Oil Drain Kit for Pumps Shown Above

DULTMEIER SALES • OMAHA, NE

$ 43.95 43.05 49.85

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

Wt. Lbs 132 112 139 113 139 113 139 113

Call Toll Free For Prices

E0031


PISTON PUMPS

49

CAT PUMPS® TRIPLEX PISTON PUMPS are designed to deliver smooth, low pulsation flows at a wide variety of pressures and flow rates. Widely used in continuous duty, high pressure applications including Car/Truck Wash, Industrial Cleaning, Pressure Washing, Reverse Osmosis, Water Misting and many more. CAT PUMPS® are the “Pumps with Nine Lives”. Standard Features include: Wetted cups and floating pistons that are lubricated and cooled by the solution being pumped • Oil-bath crankcase • 304SS Discharge valves • Chrome-Plated brass or stainless steel manifolds • Heavy-duty connecting rods • Rated to 160° F. Seal options up to 180° F. available • All wet end parts are easily serviced without entering the crankcase. Note: Mounting rails and mounting kits are not included and must be ordered separately).

Call Toll-Free for Current Prices ! Ask About Our Quantity Discounts !

D D D

623 & 820

390

280 & 290

Pump No. GPM PSI RPM Inlet

Outlet

Shaft

Wt.

Mounting Kit

CC 280 3.0 2.0

1000 600

1330 1/2" 3/8" 16.5mm 12 lbs. 887

30651/*30612

CC 290 3.5 3.0 2.5

1200 1000 800

1200 1/2” 1029 858

3/8”

16.5mm

12 lbs.

30651/*30612

CC 333 4.0 3.0 2.0

1200 1000 800

1070 1/2” 803 535

3/8”

16.5mm

18 lbs.

30652/*30611

CC 430 5.0 4.0 3.0

1000 800 600

1040 1/2” 832 624

3/8”

16.5mm

18 lbs.

30652/*30611

CC 323 5.0 4.0 3.0

1500 1200 1000

1000 1/2” 800 600

3/8”

20mm

17 lbs.

30659/*30611

CC 623 6.0 4.0

1200 800

850 1” 567

3/4”

25mm

35 lbs.

30653/*30611

CC 820 10.0 9.0 8.0

1000 900 800

940 1” 846 752

3/4”

25mm

35 lbs.

30653/*30611

CC 390 12.0 10.0 8.0

600 500 400

1200 1/2” 3/8” 1000 800

20mm

19 lbs.

30659/*30611

CC 1010 13.0

700

900

3/4”

25mm

35 lbs.

30653/*30611

CC 1520 15.0 10.0

1000 800

830 1-1/4” 550

1”

30mm

70 lbs.

*30614

CC 2520 25.0 15.0

800 500

770 1-1/4” 465

1”

30mm

70 lbs.

*30614

CC 6040 40

1500

500

2”

1-1/4”

45mm

235 lbs.

Included

CC 6020 60 * Mounting Rails Only.

1000

500

2”

1-1/4”

45mm

235 lbs.

Included

1”

OPTIONAL MOUNTING KIT COMPONENTS 30651 Includes 30612 mounting rails, 30246 pulley (5" diameter) & key and a 25130 shaft protector cover. 30652 Includes 30611 mounting rails, 30244 pulley (8" diameter) & key and a 25130 shaft protector. 30653 Includes 30613 mounting rails, 30206 two groove pulley (9.75" diameter), 30284 hub & key assembly. 30659 Includes 30611 mounting rails, 30633 pulley (8" diameter) & key and a 118672 shaft protector.

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

SERVICE & REPAIRS Did you know? We can service almost every brand of pump we sell in our catalog.

Call us at 1-800-228-9666 (Omaha, NE) for a quote!

(800) 553-6975

E0029


Jetting & Sewer Cleaning Pumps

50

High flow, high pressure pumps are the ideal choice for pipe cleaning, water jetting, sewer cleaning, hydrostatic testing, tank cleanout and plant washdown. Pumps from Cat Pumps®, General and Giant Industries. All plunger pumps shown feature brass, stainless, aluminum/bronze or nickel-plated manifolds as noted. Triplex ceramic plunger design. Pressure and safety relief valves as well as pulsating valves are available for many models. (Note: All pumps are standard with Right Hand shaft when facing pump manifold or some feature dual shaft design. Left hand models are also available). GU LP200 Left Hand Shown

D

CC 6760

D

KE Series Right Hand Shown

D

D

GU GP7255A Dual Shaft D

CC 3560 Dual Shaft Part No. Flow Pressure

RPM

Brand

Manifold

Wt.

CC 1560 8 4000 1140 Cat Pumps® Brass CC 660 10 3000 1430 Cat Pumps® Bronze IP KE22A 10 3600 1450 General 420SS CC 3507 10 5000 915 Cat Pumps® Nickel/Bronze CC 6810 10 10,000 600 Cat Pumps® Stainless IP KE24A 12 3000 1450 General 420SS GU MP4124 12 3000 1420 Giant Alum/Bronze UD NX55/200 14 3000 1450 Udor Brass CC 3517 14 3600 800 Cat Pumps® Nickel/Bronze GU LP301A 14 4000 1270 Giant Alum/Bronze GU LP400 15 3600 1000 Giant Alum/Bronze IP KE28A 16 2200 1450 General 420SS AR RTX70 18.5 2000 1450 AR Nickel/Brass UD PD7280R 18.0 4000 1750 Udor Brass AR RTJ70 18.5 4000 1000 AR Brass CC 2510 20 2000 1450 Cat Pumps® Brass UD NX75/150 20 2200 1450 Udor Brass GU LP200 20 2900 1000 Giant Alum/Bronze CC 3560 20 4000 1160 Cat Pumps® Brass/Stainless IP HF25A 20 4000 1000 General 420SS CC 2530 25 1000 1150 Cat Pumps® Brass GU P536 26 1750 1450 Giant Brass GU LP255 26 2200 950 Giant Brass AR RTX100 26.5 1800 1450 AR Nickel/Brass IP KS28A 30 3600 1500 General Nickel/Cast UD VX130/160 33 2500 1000 Udor Brass IP KF36A 40 1900 1000 General 420SS GU LP123A 40 2000 885 Giant Alum/Bronze UD VX160/130 40 2000 1000 Udor Brass IP MSS40 44 3900 750 General Nickel/Cast IP MSS45 56 3000 750 General Nickel/Cast CC 6760 60 1200 520 Cat Pumps® Brass CC 6775 75 1200 520 Cat Pumps® Brass IP MSS50 69 2500 750 General Nickel/Cast GU GP7255A 80 2000 850 Giant Nickel/Cast IP MK60A 90 2500 1500 General Nickel/Cast IP MK65A 107 2200 1500 General Nickel/Cast

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

60 lbs. 44 lbs. 88 lbs. 152 lbs. 377 lbs. 88 lbs. 72 lbs. 75 lbs. 152 lbs. 110 lbs. 105 lbs. 88 lbs. 72 lbs. 110 lbs. 198 lbs. 80 lbs. 75 lbs. 119 lbs. 145 lbs. 132 lbs. 79 lbs. 93 lbs. 119 lbs. 72 lbs. 212 lbs. 160 lbs. 220 lbs. 116 lbs. 160 lbs. 570 lbs. 570 lbs. 335 lbs. 335 lbs. 570 lbs. 375 lbs. 862 lbs. 862 lbs.

Net Ea.

$ 2300.00 2098.00 3373.00 6095.00 27980.00 3373.00 4891.00 2698.00 5998.00 7497.00 6498.00 3373.00 1498.00 3925.00 3698.00 3525.00 2698.00 7575.00 5798.00 5375.00 3298.00 2360.00 6298.00 1498.00 8798.00 4484.00 4598.00 3498.00 4484.00 11122.00 11122.00 12750.00 14950.00 11122.00 15688.00 15429.00 15423.00

www.dultmeier.com

D

SERVICE & REPAIRS Did you know? We can service almost every brand of pump we sell in our catalog.

Call us at 1-800-228-9666 (Omaha, NE) for a quote!

• DAVENPORT, IA

(800) 553-6975

E0867


REPAIR KITS

51 VALVE KITS, CUP KITS & SEAL KITS

VALVE KITS

CUP KITS

VALVE KIT #30821 For Pumps: 310, 340 & 350, 5CP Series

Cup Kit #30023 For Pump No’s. 280, 290, 400, 410, 420 & 430

3 3 3 3 3 3 3

3 3 1 3

44565 43750 43723 43725 43358 48361 17615

Spring Retainer Valve Spring (304 S.S.) Valve (304 S.S.) Valve Seat (304 S.S.) O-Ring, Valve Seat (Buna-N) Back-up Ring, Valve Seat O-Ring, Valve Plug (Buna-N)

3 3 3 1

3 43780 Valve Spring Retainer 3 43251 Valve Spring 3 43721 Valve 3 43779 Valve Seat 3 43793 O-Ring, Valve Seat

VALVE KITS Valve Kit #34052 For 2SF Pumps 3 44565 Spring Retainer 3 541062 Spring 3 26089 O-Ring, D.V. Adapter 3 43723 Valve 3 44881 Seat

Valve Kit #33062 For 3CP Pumps 3 17547 O-Ring 3 46658 Seat 3 43723 Valve 3 43750 Spring 3 44565 Retainer, Spring 3 17615 O-Ring

Valve Kit #34055 For 4SF Pumps 3 44564 Spring Retainer 3 43751 Valve Spring 3 43721 Valve 3 45194 Seat 3 43781 O-Ring 3 21986 Back Up Ring, Adapter

Valve Kit #30915 For 230, 240 & 270 Pumps 3 3 3 3 3 3 3 3

43907 43750 43723 44002 44001 17547 43893 26089

Spring Retainer (304 S.S.) Spring (304 S.S.) Valve (304 S.S.) Valve Seat (304 S.S.) O-Ring, Valve Seat (Buna-N) O-Ring, Adapter (Buna-N) O-Ring, Adapter (Buna-N) O-Ring, Spacer (Buna-N)

Discharge Valve Kit #30024 For Pumps: #280, 300, 333, 410, 420 & 430 3 3 3 3 3

22841 22031 23172 29487 22842

Valve Spring Retainer Valve Spring O-Ring, Cylinder Discharge Valve Seat Discharge Valve

Discharge Valve Kit-Quiet Valve #30686 For Pumps: 280, 290, 333, & 430 3 3 3 3 3

23172 43434 43723 43360 43442

O-Ring, Cylinder Q.V. Starting Discharge Valve Seat Q.V. with S/N Discharge Valve Q.V. 0800101-280 Spring Q.V. 333,430 Retainer Q.V. All Models-290

44564 43751 43721 43722 43249 43248 17617

3 3 3 3 1

3 3 3 1

Cup (Viton®) O-Ring, Cylinder Cotter Pin (1.5x10) Back Up Ring Cup Inserter

43172 14158 26969 22130

Cup (Viton®) Cotter Pin (1.5x10) O-Ring, Cylinder Cup Inserter

3 27821 Cup, Piston (Viton®) 3 26969 O-Ring, Cylinder 3 14158 Cotter Pin-SS (M1.5 x 10) 3 28204 Back-Up-Ring 1 16981 Cup Inserter

43429 43251 43721 43428 26966 43062 26969 28204

Spring Retainer Q.V. Starting Spring Q.V. with S/N Valve Q.V. 9800101 Valve Seat Q.V. O-Ring, Valve Q.V. Back-up Ring, Valve Seat O-Ring, Cylinder Q.V. Back-up Ring, Cylinder

Cup Kit #30440 For 6020 Pumps 3 3 3

43135 20265 26969 43063 43062 20262 28204 26966

Valve Spring Retainer Starting with s/n Valve Spring 4770951-623 O-Ring, Cylinder 577021-820 Discharge Valve Seat 5770421-1010 Back-Up Ring, D.V.S. Discharge Valve Back-Up Ring, Cylinder O-Ring, Discharge Valve Seat

3 43248 3 43249 3 44718 3 43721 3 43751 3 44564 3 17617

SLEEVE & PRRRRRM-A-LUBE SEAL KIT #30431 For Pump No.’s 280 & 290 3 3 3 3 3

30315 25327 14158 29614 25392

Prrrrrm-A-Lube Seal Starting with s/n Barrier Slinger-SS 77600858-280 Cotter Pin-SS (M1.5x10) Sleeve (Stopped) O-Ring, Sleeve

SLEEVE & PRRRRRM-A-LUBE SEAL KIT #30397 For Pump No.’s 280, 520, 623, 820 & 1010 3 30315 Prrrrrm-A-Lube Seal 3 14158 Cotter Pin-SS (M1.5x10) 3 25327 Barrier Slinger-SS 3 27340 Sleeve 3 25392 O-Ring, Sleeve

Backup Ring, Valve Seat O-Ring, Valve Seat Valve Seat Valve Valve Spring Spring Retainer O-Ring, Valve Plug

SLEEVE & PRRRRRM-A-LUBE SEAL KIT #30312 For Pump No.’s 323, 333 & 430 3 30315 Prrrrrm-A-Lube Seal 3 14158 Cotter Pin-SS (M1.5x10) 3 25327 Barrier Slinger-SS 3 25299 Sleeve 3 25392 O-Ring, Sleeve

Valve Kit #34235 For 3520 & 3535 Pumps 44728 44109 43932 44727 26142 48363 89827 48364 44729

29461 Piston Assembly 12392 O-Ring, Cylinder 29354 Cotter Pin (M2.5x25)

SLEEVE & SEAL KITS

Discharge Valve Kit #34920 For Pump: 1050

3 3 3 3 3 3 3 3 3

43717 23172 14158 21985 43749

Cup Kit #30222 For 820 Pumps

Discharge Valve Kit (B Manifold) #30449 For Pumps: 623, 820 & 1010 3 3 3 3 3 3 3 3

Cup (Buna N) O-Ring, Cylinder Cotter Pin (1.5x10) Cup Inserter

Bac-Cup Kit #30822 For 623 Pump

Spring Retainer Valve Spring (304 S.S.) Valve (304 S.S.) Valve Seat (304 S.S.) O-Ring, Valve Seat (Buna-N) Back-up Ring, Valve Seat O-Ring, Valve Plug (Buna-N)

Discharge Valve Kit-Quiet Valve #30687 For Pumps: 10R, 623, 820, 1010 3 3 3 3 3 3 3 3

43792 43781 14158 43548

Bac-Cup Kit #30841 For 333 Pumps

Discharge Valve Kit #30820 For Pumps: 51, 530, 550 & 650 3 3 3 3 3 3 3

Cup, Piston O-Ring, Cylinder Cup Inserter Cotter Pin-SS (M1.5X10)

Bac-Cup Kit #30858 For 323 Pumps

Valve Kit #30859 For 323 Pumps

Call for Pricing!

43172 23172 22130 14158

Spring Retainer, Threaded Valve Spring (316 S.S.) Valve (304 Stainless Steel) Valve Seat, Stepped (304 S.S.) O-Ring, Valve Seat (Buna-N) Back-up Ring, Valve Seat O-Ring, Valve Plug (Buna-N) Back-up Ring, Valve Plug Washer (M31) - (316 S.S.)

SLEEVE & SEAL KIT #30485 For Pump No.’s 6020 & 6040 3 3 3 3 3 3 3

* NOTE: All individual parts may be ordered separately if required.

43130 43136 29340 13967 43129 29455 29354

Seal (M25) Wick (M25) Barrier Slinger O-Ring, Sleeve Sleeve (M25) Back-Up Ring Cotter Pin-SS (M2.5x25)

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0034


REPAIR KITS SEAL KITS, PISTON KITS, OIL & LUBRICANTS

PISTON KITS

SEAL KITS SEAL KIT #30610 For No. 51, 55, 550 Pumps

BAC-CUP PISTON KIT #30857 For 323 Pumps

3 43316 Lo-Pressure Seal 3 20285 O-Ring, Seal Case 6 43319 V-Packing 3 43313 Wick, Long Tab 3 17399 O-Ring, Plunger Retainer

6 3 3 3 3 3 3 3 3 3 3

SEAL KIT #30488 For No. 53, 58, 530 Pumps 3 3 3 3 3

SEAL KITS SEAL KIT #34053 For 2SF Pumps 3 3 6 3

43245 44876 26089 14158

Hi-Pressure Seal (Buna-304 S.S.) Lo-Pressure Seal (Buna-304 S.S.) O-Ring (Buna-N) Cotter Pin

SEAL KIT #33983 For 3CP Pumps 3 46730 3 43243 3 13976 3 43245

Washer, Seal Seal, LPS O-Ring Seal

SEAL KIT #34054 For 4SF Pumps 6 3 6 3

45191 45188 43781 14158

V-Packing (Buna) Lo-Pressure Seal O-Ring (Buna-N) Cotter Pin

SEAL KIT #30914 For No. 230, 240 & 270 Pumps 3 3 6 3 3 3 6

43245 43243 26089 43893 17547 17399 44001

Hi-Pressure Seal (Buna-N) Low-Pressure Seal (Buna-304 S.S.) O-Ring, Spacer (Buna-N) O-Ring (Buna-N) O-Ring (Buna-N) O-Ring, Plunger Retainer (Buna-N) O-Ring (Buna-N)

PRRRRRM-A-LUBE SEAL KIT #30305 For Pumps 280, 290, 323, 333, 430, 623 & 820 3 3 2

43245 20285 43243 17399 43239

Hi-Pressure Seal (Buna-N) O-Ring, Seal Case Lo-Pressure Seal (Buna-304 S.S.) O-Ring, Plunger Retainer Wick, Long Tab

SEAL KIT #30799 For 56, 57, 59 & 60 Pumps 3 43243 Lo-Pressure Seal 3 43239 Wick, Long Tab 6 44549 V-Packing 3 20285 O-Ring 3 17399 O-Ring, Plunger Retainer

SEAL KIT #30913 For 1050 Pumps 3 6 3 3 3

44035 103692 14762 17399 44036

Lo-Pressure Seal (304 S.S.-Buna-N) V-Packing (Buna-Comp.) O-Ring (Buna-N) O-Ring, Plunger Retainer (Buna-N) Snap Ring

SEAL KIT #31040 For 3531, 3535 & 3537 Pumps 3 6 6 6 3 3

44113 44609 18697 48362 11379 11345

Lo-Pressure Seal (Buna-316 S.S.) V-Packing (Teflon) O-Ring (Buna-N) Back-up Ring O-Ring (I.M.-Buna-N) O-Ring, Plunger Retainer (Buna-N)

3 3 3 1

43130 43136 29354 30168

Seal (M25) Wick (M25) Cotter Pin (M2.5x25) S.S. Abrasive Paper

Call for Pricing!

Pump Oil & Lubricants

Hi-Pressure Seal Low-Pressure Seal O-Ring, Seal Case O-Ring, Plunger Retainer Wick, Long Tab

SEAL KIT #30229 For pumps:333 & 430 3 25153 Blu-dot seal 3 27711 Wick 3 14158 Cotter Pin-SS (M1.5x10) 2 30168 Abrasive Paper, 400 Grit

SEAL KIT #33628 For 5CP2120W Pumps 3 46730 Seal Washer 3 43305 Low Pressure Seal 3 13978 O-Ring 3 43307 Hi-Pressure Seal

* NOTE: All individual parts may be ordered separately if required.

O-Ring, Cylinder Back-up Ring, Cylinder Inlet Valve Bac-Cup Piston Bac-Cup Ring Bac-Cup (Buna-N) Piston Spacer Piston Retainer Conical Washer (M6) Slotted Nut (M6) Cotter Pin

3 3 3 6 3 3 3 3 3

28339 43826 14158 23172 21985 27983 27002 27006 27000

Inlet Valve Bac-Cup Assembly Cotter Pin O-Ring, Cylinder Back-up Ring Spacer, Piston Retainer, Piston Washer, Conical Nut, Slotted

PISTON KIT #30210 For 430 Pumps 6 23172 O-Ring, Cylinder 3 27004 Inlet Valve 3 22021 Piston 3 43172 Cup, Piston (Viton®) 3 27983 Piston Spacer 3 27002 Piston Retainer 3 27006 Conical Washer (M6)-S.S. 3 27000 Slotted Nut (M6)-S.S. 3 14158 Cotter Pin (M1.5x10)-S.S. 1 22130 Cup Inserter

BAC-CUP PISTON KIT #30843 For 623 Pumps 27347 43474 14158 26969 28204 22130

Inlet Valve Bac-Cup Assembly Cotter Pin O-Ring, Cylinder Bac-Cup Ring Cup Inserter

PISTON KIT #30221 For 820 Pumps

30315 Prrrrm-A-Lube Seal 14158 Cotter Pin-SS (M1.5x10) 30168 Abrasive Paper, 400 grit

43307 43305 14200 17399 43302

43781 21986 43533 43787 43788 43792 27983 29588 27006 27000 14158

BAC-CUP PISTON KIT #30842 For 333 Pumps

3 3 3 6 3 1

SEAL KIT #30484 For No. 60FR Pumps

SEAL KIT #30623 For 310, 340 & 350 Pumps 3 3 3 3 3

52

6 26969 O-Ring, Cylinder 3 27497 Inlet Valve 3 27820 Piston 3 27821 Cup, Piston (Viton®) 3 27500 Piston Retainer 3 27499 Piston Spacer 3 27006 Conical Washer (M6)-S.S. 3 14158 Cotter Pin (M1.5x10)-S.S. 3 28204 Back-up Ring 3 27000 Slotted Nut (M6)-S.S. 1 16981 Cup Inserter

Seal Case Removal Tools

D

CAT Pumps® Oil is a specially formulated Crankcase oil for high pressure pumps. Contains anti-wear, rust inhibitor and deoxidizer additives. 30 wt. non-detergent.

30696

Gear Box Lube is 80/90 wt. & has ISO 220 rating. Part No. Size Wt. Net Ea. CC 6100-1 21 oz. * 1-1/2 lbs. $ 8.45 CC 6105-1 2-1/2 Gallon * 18 lbs. 83.95 CC 6109 30 Gallon Drum 220 lbs. 660.00 CC 6106 Anti Seize Lubricant Tube.... 1.60 CC 6124 Liquid Gasket 3 oz. tube...... 38.95 Gearbox Lube CC 6111-1 16 oz. 1 lbs. $ 12.75 *Additional 10% Discount if Full Case Purchase 6100-1 is 12 per case. 6105-1 is 2 per case.

1/2” Drive Socket Tools for easy removal of seal cases from Cat Pumps Part No. CC 33004 CC 33005 CC 33006

Pumps Net Ea. 310, 340, 350, 31.......... $ 49.95 530, 550, 56, 57, 70...... 47.60 650, 1050, 1530............ 48.80

Valve seat removal tool for easy removal of valves from Cat Pumps Part No. CC 30696

Pumps Net Ea. 5FPR, 7FPR, 15FPR..... $ 28.75

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0033


REPAIR KITS

53

D

Models 310 • 340 • 350 CAT PUMPS® PLUNGER PUMPS

CAT Pumps® Models 310 • 340 • 350 Parts List Viton® is a registered trademark of DuPont Performance Elastomers

Qty. Qty Req'd Req'd No. Part No. Description Per Pump No. Part No. Description Per Pump 2 CC 30057 Key (M6)..................................................................................... 1 97 CC 14160 VITON® O-Ring, Plunger Retainer............................................ 3 5 CC 92519 Screw, Sems Comb Head (M6x16)............................................ 8 98 CC 45891 Gasket........................................................................................ 3 8 CC 43344 Bearing Case............................................................................. 2 99 CC 104360 Plunger Retainer........................................................................ 3 10 CC 43343 O-Ring, Bearing Case................................................................ 2 100 CC 45688 Seal Retainer, Front................................................................... 1 11 CC 43222 Oil Seal, Crankshaft - (310, 350-2) (340-1)................................ 2 101 CC 43302 Wick .......................................................................................... 1 15 CC 14480 Bearing....................................................................................... 2 106 CC 43305 Lo-Pressure Seal with Spring, BUNA......................................... 3 20 CC 45883 Connecting Rod Assembly......................................................... 3 106 CC 45153 Lo-Pressure Seal with Spring, VITON®..................................... 3 25 CC 43342 Crankshaft - Dual End - 310, 311, 317....................................... 1 120 CC 45679 Seal Case................................................................................... 3 CC 44945 Crankshaft - Single End - 340, 341, 347.................................... 1 121 CC 14200 O-Ring, Seal Case, BUNA......................................................... 3 CC 43838 Crankshaft - Dual End - 350, 351, 357....................................... 1 121 CC 11719 O-Ring, Seal case, VITON®....................................................... 3 30 CC 44949 Blind Shaft Cover - 340.............................................................. 1 125 CC 43307 High Pressure Seal.................................................................... 3 32 CC 43211 Oil Filler Cap.............................................................................. 1 139 CC 22179 Plug, Inlet 1/2"............................................................................ 1 CC 44666 Oil Filler Cap, Domed - Gearbox Models................................... 1 162 CC 48361 Back-up Ring, Valve Seat........................................................... 6 33 CC 14177 O-Ring, Filler Cap...................................................................... 1 163 CC 43358 O-Ring, Valve Seat..................................................................... 6 37 CC 92241 Oil Gauge, Bubble...................................................................... 1 164 CC 43725 Valve Seat.................................................................................. 6 38 CC 44428 Gasket, Flat, Oil Gauge.............................................................. 1 166 CC 43723 Valve........................................................................................... 6 40 CC 92520 Screw, Sems Comb Head (M6x20)............................................ 4 167 CC 43750 Valve Spring............................................................................... 6 48 CC 25625 Drain Plug.................................................................................. 1 168 CC 44565 Retainer, Valve Spring................................................................ 6 49 CC 23170 O-Ring, Drain Plug..................................................................... 1 172 CC 17615 O-Ring, Valve Plug..................................................................... 6 50 CC 43339 Crankcase Cover........................................................................ 1 174 CC 43849 Valve Plug.................................................................................. 6 51 CC 43340 O-Ring, Crankcase Cover......................................................... 1 185 CC 44837 Manifold Head............................................................................ 1 53 CC 48769 Crankcase (4 Screw, Large Cap)............................................... 1 186 CC 126231 Washer, Split Lock (M10), Manifold Head.................................. 2 56 CC 43355 Oil Pan........................................................................................ 1 188 CC 124396 Bolt, Hex Socket (M10x35), Manifold Head................................ 2 64 CC 43351 Pin, Plunger Rod........................................................................ 3 250 CC 118672 Shaft Protector (Belt Drive Only................................................. 1 65 CC 43365 Plunger Rod............................................................................... 3 255 CC 30243 Direct Mount Kit (Belt Drive Only).............................................. 1 70 CC 43228 Oil Seal, Crankcase................................................................... 3 Angle Rail Mounting - B - (28499, 30900, 30910, 30920) (Belt Drive Only). 1 260 CC 30611 75 CC 43328 Barrier Slinger............................................................................ 3 Complete Mounting Kit (30611, 30633, 30944, 109692) (Belt Drive Only) 1 265 CC 30659 83 CC 45688 Seal Retainer - Rear 3 270 CC 30633 Pulley & Key Assy. (30058, 30057) (Belt Drive Only)................. 1 85 CC 43302 Wick - Long Tab 2 Pc. 3 300 CC 30623 Seal Kit (Includes: 97, 101, 106, 121, 125)................................ 1 86 CC 45688 Seal Retainer Adapter 3 310 CC 30821 Valve Kit (Includes: 162 - 165, 168, 172).................................... 2 88 CC 45697 Washer, Keyhole (M18).............................................................. 3 350 CC 30696 Valve Seat Removal Tool............................................................ 1 90 CC 43367 Plunger (M71)............................................................................ 3 351 CC 33004 Seal Case Removal Tool............................................................ 1 96 CC 43235 Back-Up Ring, Plunger Retainer................................................ 3 97 CC 17399 BUNA O-ring, Plunger Retainer................................................. 3

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0035


REPAIR KITS

54

D

D

Models • 5CP2120W • 5CP2140W • 5CP2150W CAT PUMPS® PLUNGER PUMPS

Models 5CP2120W • 5CP2140W • 5CP2150W Parts Breakdown

CAT Pumps®

Viton® is a registered trademark of DuPont Performance Elastomers

Models 5CP2120W • 5CP2140W • 5CP2150W Parts List Qty. Qty Req'd Req'd No. Part No. Description Per Pump No. Part No. Description Per Pump 2 CC 30057 Key (M6)..................................................................................... 1 99 CC 48201 Retainer, Plunger with Stud (M7) .............................................. 3 100 CC 46749 Retainer, Seal ............................................................................ 3 5 CC 96031 Screw, Sems HHC (M6x16)....................................................... 8 106 CC 43305 Seal, LPS with S-Spg., BUNA .................................................. 3 8 CC 46910 Cover Bearing............................................................................ 2 CC 45153 Seal LPS with S-Spg., VITON® ................................................ 3 10 CC 14028 O-Ring, Bearing Cover............................................................... 2 120 CC 46843 Seal Case, Press-in-Style.......................................................... 3 11 CC 43222 Oil Seal, Crankshaft - (310, 350-2) (340-1)................................ 2 121 CC 13978 O-Ring, Seal Case, BUNA......................................................... 3 15 CC 14480 Bearing....................................................................................... 2 CC 14329 O-Ring, Seal case, VITON®....................................................... 3 20 CC 48742 Connecting Rod Assembly......................................................... 3 CC 14329 O-Ring, Seal case, VITON®....................................................... 3 25 CC 46928 Crankshaft - Dual End - 2120W, 3120, 5120, 6120.................... 1 125 CC 43307 High Pressure Seal, BUNA........................................................ 3 CC 48203 Crankshaft - Single End - 2140W............................................... 1 CC 44936 High Pressure Seal, VITON® .................................................... 3 CC 46982 Crankshaft - Dual End - 2150W................................................. 1 CC 46667 High Pressure Seal, EPDM ....................................................... 3 31 CC 828710 Protector, Oil Cap....................................................................... 1 139 CC 22179 Plug, Inlet 1/2"............................................................................ 1 32 CC 46798 Oil Filler Cap (Domed)............................................................... 1 162 CC 48361 Back-up Ring, Valve Seat........................................................... 6 33 CC 14179 O-Ring, Oil Filler Cap................................................................. 1 163 CC 43358 O-Ring, Valve Seat, BUNA......................................................... 6 37 CC 92241 Oil Gauge, Bubble...................................................................... 1 CC 44938 O-Ring, Valve Seat, VITON® ..................................................... 6 38 CC 44428 Gasket, Flat, Oil Gauge.............................................................. 1 164 CC 43725 Valve Seat.................................................................................. 6 40 CC 92519 Screw, Sems HHC (M6x16)....................................................... 4 166 CC 43723 Valve........................................................................................... 6 48 CC 25625 Drain Plug.................................................................................. 1 167 CC 43750 Valve Spring............................................................................... 6 49 CC 23170 O-Ring, Drain Plug..................................................................... 1 168 CC 44565 Retainer, Valve Spring................................................................ 6 50 CC 46940 Crankcase Cover........................................................................ 1 172 CC 17615 O-Ring, Valve Plug, BUNA......................................................... 6 51 CC 14044 O-Ring, Crankcase Cover......................................................... 1 CC 15855 O-Ring, Valve Plug, VITON® ..................................................... 6 53 CC 48617 Crankcase ................................................................................. 1 174 CC 43849 Valve Plug.................................................................................. 6 64 CC 46746 Pin, Rist...................................................................................... 3 185 CC 48245 Manifold Head .......................................................................... 1 65 CC 48458 Plunger Rod............................................................................... 3 188 CC 126513 Bolt, Hex Socket (M8x70), Manifold Head.................................. 8 70 CC 46838 Oil Seal, Crankcase................................................................... 3 196 CC 22187 Discharge Plug (3/8") ................................................................ 1 75 CC 43328 Barrier Slinger............................................................................ 3 250 CC 118672 Shaft Protector .......................................................................... 1 88 CC 45697 Washer, Keyhole (M18).............................................................. 3 255 CC 30243 Direct Mount Kit.......................................................................... 1 90 CC 46841 Plunger (M50)............................................................................ 3 Angle Rail Mounting - B - (28499, 30900, 30910, 30920) (Belt Drive Only). 1 260 CC 30611 98 CC 46730 Seal Washer, 304SS.................................................................. 3 CC 48394 Seal Washer, VITON® ............................................................... 3 283 CC 34334 Kit, Oil Drain .............................................................................. 1

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0036


REPAIR KITS

55

Model 3535 CAT PUMPS® PLUNGER PUMP

D

Model 3535 Parts Breakdown

Model 3535 — Parts List No. Part No. Description 2 CC 34021 Key (M10x6x32) 5 CC 125753 Screw, Sems HHC (M8x25) 8 CC 44542 Cover, Bearing 9 CC 815279 Shim, Split Bearing Cover 10 CC 12398 O-Ring, Bearing Cover 11 CC 13296 Seal, Oil, Crankshaft 15 CC 29326 Bearing 20 CC 121467 Rod, Connecting Assembly 21 CC 126749 Locking Washer (M10) 22 CC 126593 Washer (M10) 23 CC 88155 Screw, HH (M10x60F) 25 CC 29325 Crankshaft, Dual End 31 CC 828710 Protector, Oil Cap 32 CC 43211 Cap, Oil Filler 33 CC 14177 O-Ring, Oil Filler Cap - 70 34 CC 44319 Bolt., Eye (M12x1.75) 37 CC 92241 Gauge, Oil, Bubble 38 CC 44428 Gasket, Flat 40 CC 11824 Screw, Sems, HHC (M8x25) 48 CC 25625 Plug, Drain (1/4"x11) 49 CC 23170 O-Ring, Drain Plug 50 CC 45936 Cover, Crankcase 51 CC 16612 O-Ring, Crankcase Cover 53 CC 44559 Crankcase 55 CC 27488 Pins, Guide 56 CC 27790 Pan, Oil 59 CC 92519 Screw, Sems HHC (M6x16)

No. 64 65 69 70 75 88 90 95 96 97 98 99 100 101 106 107 110 112 117 126 127 128 141 142 155 156 157

Part No. CC 43864 CC 45116 CC 126587 CC 100488 CC 43865 CC 45676 CC 43921 CC 89778 CC 20189 CC 11345 CC 44085 CC 44084 CC 814279 CC 44112 CC 44113 CC 43925 CC 46392 CC 11379 CC 44585 CC 46494 CC 44609 CC 43928 CC 45113 CC 46352 CC 48860 CC 48362 CC 45369

Description Pin, Rist Rod, Plunger Washer, Oil Seal Seal Oil, Crankcase Slinger, Barrier Washer, Keyhole (M16) Plunger (M77) Stud, Plunger Retainer (M10x122) Back-up Ring, Plunger Retainer O-Ring, Plunger Retainer Gasket, Retainer Retainer, Plunger (M10) Retainer, Seal, 2-Pc. Wick, Long Tab Seal, LPS w/SS-Spg. Spacer, Lo-Pressure Seal Manifold, Inlet O-Ring, Inlet Manifold Screw, HSH (M14x40) Adapter, Female V-Packing, White Adapter, Male Springs, Coil Spacer, with Coil Springs O-Ring, V-Packing-Spacer Back-Up Ring, Spacer Spacer, V-Packing

No. Part No. Description 158 CC 48362 Back-Up Ring, V-Packing-Spacer 159 CC 48860 O-Ring, V-Packing-Spacer 162 CC 48363 Back-Up Ring, Valve Seat 163 CC 26142 O-Ring, Seat 164 CC 44727 Seat, Stepped 166 CC 43932 Valve 167 CC 44109 Spring 168 CC 44728 Retainer, Spring 170 CC 44729 Washer, Spring Retainer 171 CC 44644 Coil Spring (70kg), Valve Plug 172 CC 89827 O-Ring, Valve Plug - 90 173 CC 48364 Back-Up Ring, Valve Plug 174 CC 46444 Plug, Valve 185 CC 76394 Manifold, Discharge 188 CC 89981 Screw, HSH (M12x70) 250 CC 44516 Protector, Shaft w/2 89283 Screws 260 CC 92674 Mounting, Box Assembly 278 CC 80540 Screw, HH (M12x100) 279 CC 30278 Oiler (1 oz.) 281 CC 30967 Glass, Oiler 282 CC 10069 Gasket, Oiler 283 CC 34334 Kit, Oil Drain 290 CC 6124 Gasket, Liquid (1.5 oz.) 299 CC 814821 Complete Head 300 CC 31040 Kit, Seal 310 CC 34235 Kit, Valve

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0037


WANNER Pumps • Valves • Repair Kits

56

WANNER Hydra-Cell Pumps For Difficult fluids such as: • Reclaim Water • Abrasives • Hot Solutions to 250° F (300° F. with special seals) • Slurries • Wettable Powders • Fertilizers

D

D

Model D10 Model H25

Solutions never come in contact with the pumping mechanism. Diaphragm design has no cups, packings or mechanical seals; this means less maintenance and down-time. Hydra-Cell pumps are American-Made, positive displacement pumps. They are self-priming and can be run dry without damage. Hydraulically balanced diaphragms and Timken roller bearings are standard features. Shaft rotation can be in either direction for ease of mounting. MATERIALS: Brass pump manifolds. Buna-N Elastomers, Stainless Steel Valves, Seats and Valve Springs standard on all models. Rated to 160° F. on standard pumps, higher temperature pumps also available. Model D10: Rated to 8.0 GPM and 1000 PSI @ 1450 RPM. Shaft diameter is 7/8". Dimensions- (10-3/4" L x 7-1/4" W x 7-7/8" H). (Note: This pump can be ordered at flow rates of 4 or 6 GPM @ 1750 RPM if required.) Inlet is 1" and Outlet is 3/4". Model D15: Rated to 13 GPM @ 1500 PSI or 10 GPM @ 2500 PSI. Shaft diameter is 1-1/8". Dimensions- (16" L x 10" W x 12-1/2" H). Inlet is 1-1/4" FPT and Outlet is 3/4" FPT. Model H25: Rated to 20 GPM and 1200 PSI @ 1050 RPM. Shaft diameter is 1-1/8". Dimensions- (15-1/2" L x 9-1/2" W x 10" H). Inlet is 1-1/2" and Outlet is 1". Model D35: Rated to 36 GPM and 1000 PSI @ 1050 RPM. Shaft diameter is 2". Dimensions- (21" L x 11-1/2" W x 15" H). Inlet is 2-1/2" and Outlet is 1-1/4".

Hydra-Cell Bypass Valves

*Max. *Max. Max.Required Part No. Flow Pressure HP Wt. Net Ea. WN D10 8.0 GPM 1000 PSI 5.8 45 lbs. $ 1087.00 WN D15 13/10 GPM 1500/2500 PSI 15.6 145 lbs. 3398.00 WN H25 20 GPM 1000 PSI 13.9 120 lbs. 2676.00 WN D35 36 GPM 1200 PSI 30.0 240 lbs. 4750.00 WN C22A Pressure Regulator, 10 gpm, 1000 psi..................... 212.00 WN C62B Pressure Regulator, 14 gpm, 2500 psi..................... 244.00 WN C23A Pressure Regulator, 20 gpm, 1000 psi..................... 296.00 WN C24A Pressure Regulator, 40 gpm, 1000 psi..................... 679.00 WN 3431 Oil - One Quart Size (HYDRAOIL 10W30) .............. 7.50 WN 3432 Oil - 2-1/2 Gallon Size (HYDRAOIL 10W30) ............ 69.95 For specific applications, special materials of construction are available. Please give pumping requirements when ordering. * Note: Optimum Usage of Above Pumps is 10% under full rating.

Wanner Pump Repair Kits

Designed to handle the same rigorous demands as the Hydra-Cell pumps. These valves will bypass total system flow when required and will also balance system pressure for multiple gun operations. Standard valves feature Brass bodies with Buna O-rings and stainless valve seats and plunger ball. Rated to 160° F. (200° available on special request).

Common Applications: • Car Washes - Conveyor - Reclaim water. • Lawn Care - Herbicides and Fertilizers. • Carpet Cleaning - High Temperature Solutions. • Water Treatment - Reverse Osmosis and Desalination Systems. • Automatic Car Washes - High Pressure Pumping Units.

D

Model C62B features Viton®/Teflon O-rings and diaphragm and is rated to 200° F.

PUMP REPAIR KITS For Pump Valve Kit Net Ea. Diaphragm Kit (Buna) Net Ea. D10 WN D10V5 $ 136.50 D10 * WN D10V5-2 136.50 WN D10D5 $ 44.25 D15 WN D15V5 304.00 WN D15D5 201.00 H25 WN D25V5 212.50 WN D25D5 75.75 D35 WN D35V5 280.00 WN D35D5 127.50 D40 WN D40V5 597.00 WN D40D5 96.55 D10 WN D10K5 Complete Repair Kit, D10............................ $ 162.00 D25 WN D25K5 Complete Repair Kit, D25............................ 270.50 * High Flow Valve Kit Note: Repair kits of other materials are available on special request.

Part No. Flow Rate Pressure Range Ports Net Ea. WN C22A 3-10 GPM 500-1000 PSI 3/4" FPT $ 212.00 WN C23A 10-20 GPM 500-1000 PSI 1" FPT 296.00 WN C24A 20-40 GPM 500-1000 PSI 1-1/4" FPT 679.00 WN C62B 1-14 GPM 500-2500 PSI 3/4" FPT 244.00 Note: Valves with other pressure ranges are available on request. Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0606


Pumps

57

AR Plunger Pumps are designed for a wide variety of industrial cleaning, car/truck wash and pressure wash applications. Available in pulley or direct drive for electric motor or gas engines.

D

RSV Series

Standard Features Include: High strength, forged brass manifolds • Aluminum oxide ceramic plungers • Stainless steel valves, seats and springs • Continuously lubricated seals and V-packings • Triple lip oil seals • Extra long connecting rods made from a special alloy • Die-cast aluminum crankcases with oversized cooling fins • Premium bearings for exceptional load support • Maximum 140° F. • Ports on most pumps are 1/2” inlet by 3/8” outlet • Large flow pumps have larger ports • Rails are not included and must be ordered separately if needed. Direct Drive Motor Models Wt. Part No. AR RCA2G25E-F8 AR XTA2G15EBA-F8 AR RCA3G25E-F8 AR RRA3G30E-F17 AR RRA4G30E-F17 AR RKA4G30E-F17 AR RCV2G25E-F8 AR XTV2G15EBA-F8 AR RCV3G25E-F8

Flow/Pressure 2.0 gpm @ 2500 psi 2.1 gpm @ 1800 psi 3.0 gpm @ 2500 psi 3.0 gpm @ 3000 psi 4.0 gpm @ 3000 psi 4.0 gpm @ 3000 psi 2.0 gpm @ 2500 psi 2.1 gpm @ 1500 psi 3.0 gpm @ 2500 psi

RPM 1750 1750 1750 1750 1750 1750 3400 3400 3400

Lbs. 11 10 11 18 18 21 11 10 11

Flange 56C 56C 56C 182/184TC 182/184TC 182/184TC 56C 56C 56C

Shaft Net Ea. 5/8" Hollow $ 203.00 5/8" Hollow 267.00 5/8" Hollow 203.50 1-1/8" Hollow 259.00 1-1/8" Hollow 259.00 1-1/8” Hollow 377.50 5/8" Hollow 203.00 5/8" Hollow 267.00 5/8" Hollow 203.00

Flange Gas Gas Gas Gas Gas Gas Gas Gas Gas Gas Gas

Shaft Net Ea. 3/4" Hollow $ 259.00 3/4" Hollow 203.00 3/4" Hollow 129.50 3/4" Hollow 203.00 3/4" Hollow 259.00 3/4” Hollow 224.50 1" Hollow 269.00 1" Hollow 336.50 1" Hollow 292.50 1” Hollow 251.00 1” Hollow 234.00

Direct Drive Gas Engine Models Wt. Part No. Flow/Pressure AR XMV25G26D-F25 2.5 gpm @ 2600 psi AR RCV25G27D-F7 2.5 gpm @ 2700 psi AR RMV25G30EZ 2.5 gpm @ 3000 psi AR RCV3G25D-F7 3.0 gpm @ 2500 psi AR XMV3G25D-F25 3.0 gpm @ 2500 psi AR RSV3G25D-F25 * 3.0 gpm @ 2500 psi AR XMV3G30D-F24 3.0 gpm @ 3000 psi AR RKV35G30ADF24 3.5 gpm @ 3000 psi AR SXMV35G40DF24 3.5 gpm @ 4000 psi AR RRV4G36D-F24 4.0 gpm @ 3600 psi AR RSV4G40HDF40E * 4.0 gpm @ 4000 psi * Includes Built-In Unloader Valve.

D

XWL Series

D

RRA Series

D

RTF/RTJ Series

RPM 3400 3400 3400 3400 3400 3400 3400 3400 3400 3400 3400

Lbs. 15 11 8 11 15 14 16 21 16 18 14

Pulley Drive Models Wt. Part No. Flow/Pressure RPM Lbs. Flange Shaft AR XT814N 2.1 gpm @ 2000 psi 1450 11 None 24mm AR XTA2G15NBA 2.1 gpm @ 2000 psi 1750 10 None 24mm AR RCA25G25N 2.5 gpm @ 2000 psi 1750 10 None 24mm AR XTA3G19N 3.0 gpm @ 1900 psi 1750 11 None 24mm AR RCA3G25N 3.0 gpm @ 2500 psi 1750 10 None 24mm AR RCA35G25N 3.5 gpm @ 2500 psi 1750 10 None 24mm AR RRA4G30N 4.0 gpm @ 3000 psi 1750 17 None 24mm AR RKA4G30AN 4.0 gpm @ 3000 psi 1750 19 None 24mm AR RK1528HN 4.0 gpm @ 4000 psi 1450 22 None 24mm AR RKA4G40HN 4.0 gpm @ 4000 psi 1750 20 None 24mm AR SHP1550N 4.0 gpm @ 7250 psi 1450 29 None 24mm AR RK1828HN 4.7 gpm @ 4000 psi 1450 20 None 24mm AR XWM2128 5.5 gpm @ 4000 psi 1450 34 None 24mm AR SXW2135 5.5 gpm @ 5100 psi 1450 35 None 24mm AR SHP2250N 5.8 gpm @ 7250 psi 1450 29 None 24mm AR XWM2623 6.9 gpm @ 3600 psi 1450 34 None 24mm AR SXWA7G50 7.0 gpm @ 5000 psi 1750 35 None 24mm AR XW3025N 7.9 gpm @ 3600 psi 1450 34 None 24mm AR RTP30.60N * 7.9 gpm @ 8700 psi 1000 177 None 35mm AR XWAM8G35N 8.0 gpm @ 3500 psi 1750 34 None 24mm AR RTP38N * 10 gpm @ 7250 psi 1000 177 None 35mm AR XWL4121N 11 gpm @ 3000 psi 1450 34 None 24mm AR XWL50.15N 13 gpm @ 2200 psi 1450 34 None 24mm AR RTX70 18 gpm @ 2000 psi 1450 72 None 30mm AR RTJ70 * 18 gpm @ 4000 psi 1000 198 None 35mm AR RTX100 26 gpm @ 1800 psi 1800 72 None 30mm AR RTF135N * 36 gpm @ 1500 psi 800 192 None 35mm AR 1836H Rail Kit, 1-1/2” High, XT Series........................................................ AR 1837 Rail Kit, 5/8” High, RK, RKA, RKW Series....................................... AR 2633 Rail Kit, 1-3/4” High, RC, RCA, RCV, RR, RRA Series.................... AR 2633H Rail Kit, 2-5/8” High, RC, RCA, RCV, RK, RR, RRA Series............. AR AR2748 Rail Kit, 1-1/4” High, RW, SXW, XW All, Series, 5 HP..................... * Pumps have Built-In Feet that are Bolted to Baseplates.

Net Ea. $ 255.00 255.00 194.00 275.00 199.00 209.00 246.00 320.00 369.00 369.00 1200.00 377.50 509.00 669.00 1200.00 555.00 669.00 593.00 5619.00 566.00 4597.00 697.00 697.00 1498.00 3698.00 1498.00 4752.00 13.35 10.10 16.55 19.80 11.45

Hydraulic Drive Pump/Motor Units Part No. AR HYDRK1520 AR HYDXW3010

Pump Output 4 gpm @ 3000 psi 8 gpm @ 1450 psi

REPAIR KITS

D

Hydraulic Units

(800) 228-9666

Wt. 26 lbs. 43 lbs.

Part No. AR AR1828 AR AR1864 AR AR2780 AR AR2864 AR AR1857 AR AR1866 AR AR2189 AR AR2278 AR AR2741 AR AR2747 AR AR2782 AR AR2546

DULTMEIER SALES • OMAHA, NE

Hydraulic Requirements 7.5 gpm @ 2500 psi 9.5 gpm @ 1800 psi

Valve Kit, XRV/XRVC/GRKV/RKV..................................................... Valve Kit, XTA, XTV, HPE, XMV......................................................... Valve Kit, XW, WWA.......................................................................... Valve Kit, RK, RKA............................................................................ Packing Kit, XRV, XRA, RKV, RK....................................................... Packing Kit, XTA, XTV, HPE.............................................................. Packing Kit, RSV................................................................................ Packing Kit, XWM.............................................................................. Packing Kit, (15mm), XMV, XM, XMA................................................ Packing Kit, XMA (18mm).................................................................. Packing Kit, XWA, (20mm)................................................................. Plunger Kit, XRCA, XRCV.................................................................

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

Net Ea. $ 666.00 909.00 Net Ea. $ 31.70 26.95 71.00 33.10 61.80 47.65 34.25 87.70 49.35 54.20 70.65 103.50 E0038


Emperor Pumps

58

High Temperature, Run-Dry Capabilities The quality that you have learned to expect from General Plunger Pumps, but now with the Emperor line, which can withstand temperatures to 185˚ F. and can even run dry for several hours. Nickel-plated manifolds provide corrosion resistant operation. High temperature, run-dry seals. New Patent-Pending valve design. Wide range of flow and pressure ranges.

HTX Series Specifically designed to handle the rigorous duty cycles, high temperatures and chemicals associated with self-service car wash applications. Also ideal for use in carpet cleaning and other high pressure cleaning applications.

D

HTS Series Specifically designed to handle the rigorous duty cycles, high temperatures and chemicals associated with self-service car wash applications. Also ideal for use in carpet cleaning and other high pressure cleaning applications. This pump offers a compact and economical design.

HTX

HTX Models Part No. GPM IP HTX1810S 3.1 IP HTX1813S 3.5 IP HTX1812S 3.8

Max. PSI 2000 2300 2000

Shaft Wt. RPM Size Lbs. Net Ea. 1750 24mm 18 $ 498.00 1450 24mm 18 498.00 1750 24mm 18 498.00

HTS Models

Shaft Wt. Part No. GPM Max. PSI RPM Size Lbs. Net Ea. IP HTS2210S 4.0 2300 1450 24mm 32 $ 669.00 IP HTS2212S 4.75 2300 1450 24mm 32 669.00 IP HTS2215S 4.0/5.0 2300 950/1200 24mm 32 679.00

D

HTS

HTF Models

HTF Series Designed for use in prep units, conveyor and multiple gun applications. Excellent for carpet cleaning and for use in industrial plant systems where hot water is required.

HTF D

Shaft Wt. Part No. GPM Max. PSI RPM Size Lbs. Net Ea. IP HTF2018S 4.0/5.0/7.5 3600 950/1200/1750 24mm 41 $ 1229.00 IP HTF2221S 8.5/10.2 3000 1450/1750 24mm 41 1275.00 IP HTF2421S 10.0/12.0 3000/2500 1450/1750 24mm 41 1325.00

HTW Models

Shaft Wt. Part No. GPM Max. PSI RPM Size Lbs. Net Ea. IP HTW3624S 18.0 1200 1000 35mm 57 $ 1598.00 IP HTCK3623S 21/25 1500/1300 1150/1350 30mm 80 2639.00 IP HTCK4050S 36 1500 800 30mm 157 3098.00

HTW Series Designed for touchless carwash systems, multiple gun systems and industrial plant systems where hot water is required.

HTCK Series Designed for use in tunnel/conveyor applications. Also perfect for use in industrial plant systems where hot water is required.

D

D

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

HTCK

HTW

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0670


GENERAL / INTERPUMP

59

Triplex and Duplex Plunger Pumps from General/Interpump. Available in Pulley Drive or DirectDrive Designs. Maximum operating temperature on most pumps is 165° F. Maximum inlet pressure is 125 PSI. 5 year limited warranty on all pumps and a lifetime warranty on manifolds against damage from freezing.

Standard Features Forged Bronze Head. Highly resistant to chemical corrosion. Unitized Valves. Easily serviced. Valves are heat treated and seats are roller burnished to provide a tight seal and extended valve life. Continuously Lubricated Dual Packing System. Keeps packings cool by recycling water back into system. Pre-loaded packings eliminate need for external gland adjustment and greasing. Solid Ceramic Plunger. Extremely hard, won’t score. Precision micron finish produces excellent seal, reduces wear on packings.

D

CW2040

Replaceable Piston Guides. Made of Teflon, graphite and bronze alloy to prolong crankcase life. Cast Aluminum Crankcase. Large capacity means better lubrication for long life operation. Connecting Rods. Large, full contact rods result in lower bearing pressure and added strength. Tapered Roller Bearings. Oversized to evenly distribute load for longer, more quiet bearing life. Forged and Hardened Steel Crankshaft. Mounting Rails. Standard with mounting rails and mounting bolts for ease in installation. Drive Design. Standard with shaft on right side when facing front of pump. (Left hand drive is available but must be specified.)

D

TS1011 LOW SPEED PLUNGER PUMPS (Pulley Drive) Part No. IP CW1012

Interpump (Cross-Ref) ———

Max. Max. Max. Wt. Pressure GPM RPM Lbs. Shaft 1200/1000 10.0/12.0 750/900 46 35mm

IP T721B W72 IP T731B W73 IP CW1541 ——— D

CW1541

D

T721B

General Pump Oil Industrial Grade Specially blended, non-detergent pump oil for General Plunger Pumps. Increases pump life and performance.

FPT Ports Inlet Outlet Net Ea. 3/4" 3/8" $ 1379.00

1200 2.2 1450 15 24mm 1/2" 3/8" 251.00 1200 3.0 1450 15 24mm 1/2" 3/8" 251.00 1200 41.0 1000 156 35mm 1" 3/4" 3357.00

IP T991B W99 1100 4.0 1450 IP TS1041B WS104 1600 8.0 1450 IP T921B W92 1700 5.0 1050 IP TS1021B WS102 1700/2500 5.6/4.5 1450/1125

19 24mm 46 35mm 32 24mm 32 24mm

1/2" 3/4" 1/2" 1/2"

3/8" 343.50 3/8" 869.00 3/8" 412.00 3/8" 454.00

IP T1011B W101 1500/2000 5.6/4.5 1450/1125 IP TS1011B WS101 2000 4.0 1450 IP TS1321B WS132 2100 4.75 1450 IP T1321B W132 2100 5.5 1150

32 24mm 32 24mm 32 24mm 32 24mm

1/2" 1/2" 1/2” 1/2"

3/8" 439.00 3/8" 439.00 3/8” 419.00 3/8" 419.00

IP TS1531 WS153 IP T1551B W155

2200 7.9 1450 46 35mm 3/4" 3/8" 1101.00 2150 14.0 1000 93 30mm 1" 3/4" 2781.00

IP CW2040 ——— IP T1621B W162

2500 5.0 1250 30 24mm 1/2" 3/8" 529.00 2500 5.0 1050 33 24mm 1/2" 3/8" 498.00

IP TSF2421 ——— 2500 10.0 1450 IP TS1711B WS171 2700 3.5 1450 IP CW3040 ——— 3000 5.0 1250 IP T2031B ——— 3000/2000 9.0/11.0 1140/1450

41 24mm 32 24mm 32 24mm 61 32mm

3/4” 1/2" 1/2" 3/4"

3/8” 929.00 3/8" 409.50 3/8" 519.00 3/8" 1362.00

IP TS2011B * WS201 IP TS1511B ** WS151 IP TS2021B WS202 IP TSF2221 ——— IP TSF2021 ——— IP TSF1819 ———

3500 3500 3500 3000 3600 4350

32 24mm 32 24mm 32 24mm 41 24mm 41 24mm 41 24mm

1/2" 1/2" 1/2" 3/4” 3/4” 3/4"

3/8" 534.00 3/8" 454.00 3/8" 509.00 3/8” 795.00 3/8” 659.00 3/8" 659.00

IP TSP1819 ——— IP TSP1619 ———

5100 5.0 1450 52 24mm 1/2" 3/8" 799.00 5800 4.3 1750 52 24mm 1/2” 3/8” 891.00

4.0 4.0 5.6 8.5 7.0 6.3

1450 1450 1450 1450 1450 1750

* NICKEL - Plated Brass Manifold. ** BRASS Manifold. D

Series 100, 30 wt. Oil is for smaller General Pumps up to size T61B. Available in 16 oz. bottles or 2-1/2 gallon jugs. Series 200, 50 wt. Oil is for Large General Plunger Pumps such as T61B and larger. Available in 16 oz. bottles or 2-1/2 gallon jugs. Oil Std. Part No. Type Pkg. *Pkg. Net Ea. IP 100214-1 30 wt. 16 oz. 24 $ 4.61 IP 100553-1 30 wt. 2-1/2 gallon 2 57.90 IP 100016-1 50 wt. 16 oz. 6 5.01 IP 100450 50 wt. 2-1/2 gallon 2 57.05 IP 100735-1 90 wt. 2-1/2 gallon 2 69.10 *10% Discount If Ordered In Std. Pkgs.

HIGH SPEED PLUNGER PUMPS (Direct Drive)

Interpump Max. Max. Part No. (Cross-Ref) Pressure GPM IP T9721B W972 1000 2.1 IP T9731B W973 1000 2.8 IP T991B W99 1100 4.0 IP TS1011B IP T9951B IP T9971B

WS101 W995 W997

IP CW2004 IP T9211B IP T9281B

1500 1500 2000

4.7 1750 32 3.5 1750 19 4.0 1750 19

———

2500

4.0 1750 30

24mm 1/2" 3/8" 517.00

W921 W928

3000 4000

4.0 1750 32 4.0 1750 33

24mm 1/2" 3/8" 523.00 24mm 1/2" 3/8" 651.00

IP TS2011B WS201 IP TSF2021 ——— IP TSF2221 ——— IP TSF2421 ———

DULTMEIER SALES • OMAHA, NE

Max. Wt. FPT Ports RPM Lbs. Shaft Inlet Outlet Net Ea. 1750 11 24mm 1/2" 3/8" $ 251.00 1750 11 24mm 1/2" 3/8" 251.00 1750 19 24mm 1/2" 3/8" 343.50

2300 4.7 1750 3600 8.5 1750 3000 10.2 1750 2500 12.0 1750

32 41 41 41

24mm 1/2" 3/8" 24mm 1/2" 3/8" 24mm 1/2" 3/8"

24mm 1/2" 24mm 3/4" 24mm 3/4" 24mm 3/4”

3/8" 3/8" 3/8" 3/8”

439.00 319.00 440.00

534.00 659.00 795.00 929.00

NOTE: Shafts are on the right side when facing pump. For Left-handed shafts, Please Specify.

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0039


General Plunger Pumps

60

Direct Drive • Forged Brass Manifolds TT Series 51 Triplex Plunger Pumps with Hollow Shaft (Flanged for Direct Couple to Electric Motor). NEMA-56C. Direct Drive D

5/8" Shaft

Part No. IP TT2021EBF IP T9051EBF IP TT9061EBF IP TT2028EBF IP TT9071EBF IP TT9111EBF

Max. Pressure 2000 1500 1500 2000 1500 1500

Max. GPM 2.1 2.1 2.1 2.8 2.8 3.0

Max. RPM 3400 1750 3400 3400 3400 1750

Shaft 5/8" Hollow 5/8" Hollow 5/8" Hollow 5/8" Hollow 5/8" Hollow 5/8" Hollow

FPT Ports Inlet Outlet 3/8" 1/4" 3/8" 1/4" 3/8" 1/4" 3/8" 1/4" 3/8" 1/4" 3/8" 1/4"

Wt./Lbs. 11.5 11.5 11.5 11.5 11.5 11.5

Net Ea. $ 248.50 262.50 252.00 241.00 249.50 259.50

EZ Series 44 Triplex Plunger Pumps with Hollow Shaft (Flanged for Direct Couple to Electric Motor). NEMA-184C. Direct Drive

D

1-1/8" Shaft

Part No. IP EZ2536E IP EZ2542E IP EZ2545E IP EZ2555E IP EZ4035E34 IP EZ4040E34

Max. Pressure 2500 2500 2500 2500 4000 4000

Max. GPM 3.6 4.2 4.6 5.5 3.5 4.0

Max. RPM 1750 1750 3400 3400 3400 3400

Shaft 1-1/8" Hollow 1-1/8" Hollow 1-1/8" Hollow 1-1/8" Hollow 1-1/8" Hollow 1-1/8" Hollow

FPT Ports Inlet Outlet 1/2" 3/8" 1/2" 3/8" 1/2" 3/8" 1/2" 3/8" 1/2" 3/8" 1/2" 3/8"

Wt./Lbs. 18.5 18.5 18.5 18.5 18.5 18.5

Net Ea. $ 329.00 355.00 329.00 329.00 379.00 379.00

TT Series 51 Triplex Plunger Pumps with Hollow Shaft, (Flanged for Direct Couple to Gasoline Engines with 3/4" Shafts). Direct Drive D

3/4" Shaft

Part No. IP TT9061GBF IP TT2028GBF IP TT9071GBF IP TT2035GBF IP TT1540GBF

Max. Pressure 1500 2000 1500 2000 1500

Max. GPM 2.1 2.8 2.8 3.5 4.0

Max. RPM 3400 3400 3400 3400 3400

Shaft 3/4" Hollow 3/4" Hollow 3/4" Hollow 3/4" Hollow 3/4" Hollow

FPT Ports Inlet Outlet 3/8" 1/4" 3/8" 1/4" 3/8" 1/4" 3/8" 1/4" 3/8" 1/4"

Wt./Lbs. 11.4 11.4 11.4 11.4 11.4

Net Ea. $ 239.00 241.00 239.00 241.00 241.00

TX Series 63 Triplex Plunger Pumps with Hollow Shaft, (Flanged for Direct Couple to Gasoline Engines with 3/4" Shafts). Direct Drive

D

3/4" Shaft

Part No. IP TX1505G6 IP TX1506G6 IP TX1508G6

Max. Pressure 3000 3000 3000

Max. GPM 2.0 2.6 3.0

Max. RPM 3400 3400 3400

Shaft 3/4" Hollow 3/4" Hollow 3/4" Hollow

FPT Ports Inlet Outlet 1/2" 3/8" 1/2" 3/8" 1/2" 3/8"

Wt./Lbs. 18.0 18.0 18.0

Net Ea. $ 270.50 270.50 270.50

TX Series 63 Triplex Plunger Pumps with Hollow Shaft, (Flanged for Direct Couple to Gasoline Engines with 1" Shafts). Direct Drive

D

1" Shaft

Part No. IP TX1506G8 IP TX1508G8 IP TX1510G8

Max. Pressure 3000 3000 3000

Max. GPM 2.6 3.0 4.0

Max. RPM 3400 3400 3400

Shaft 1" Hollow 1" Hollow 1" Hollow

FPT Ports Inlet Outlet 1/2" 3/8" 1/2" 3/8" 1/2" 3/8"

Wt./Lbs. 18.0 18.0 18.0

Net Ea. $ 279.00 277.50 277.50

EZ Series 44 Triplex Plunger Pumps with Hollow Shaft, (Flanged for Direct Couple to Gasoline Engines with 1" Shafts).

Direct Drive

Part No. IP EZ3030G34 IP EZ3035G IP EZ3040G IP EZ3045G

D

Max. Pressure 3200 3000 3000 3000

Max. GPM 3.0 3.5 4.0 4.6

Max. RPM 3400 3400 3400 3400

Shaft 1" Hollow 1" Hollow 1" Hollow 1" Hollow

FPT Ports Inlet Outlet 1/2" 3/8" 1/2" 3/8" 1/2" 3/8" 1/2" 3/8"

3400 3400 3400

1" Hollow 1" Hollow 1" Hollow

1/2" 1/2" 1/2"

Wt./Lbs. 19.1 19.1 19.1 19.1

Net Ea. $ 309.00 339.00 375.50 342.00

20.0 20.0 20.0

$ 369.00 359.00 358.50

Maximum Inlet Vacuum: Flooded IP EZ4030G34 IP EZ4035G34 IP EZ4040G34

1" Shaft

Gear Box Drive

D

1" & 1-1/8" Shaft

4000 4000 4000

3.0 3.5 4.0

3/8" 3/8" 3/8"

T Series 47 Triplex Plunger Pumps with Gear Box for Gas Engines with 1" Shafts. Shaft Dia.: 1" Part No. IP T991GR IP T9971GR IP TS1711GR IP TS1011GR IP TS1511GR IP TS2011GR IP TS1321GR IP TS1621GR IP TS2021GR

Max. Pressure 1500 2000 2700 2000 3000 3000 2100 2500 3500

Max. GPM 3.5 3.5 3.5 4.0 4.0 4.0 4.75 4.75 5.6

Max. RPM 3400 3400 3400 3400 3400 3400 3400 3400 3400

Shaft 1" Hollow 1" Hollow 1" Hollow 1" Hollow 1" Hollow 1" Hollow 1" Hollow 1" Hollow 1" Hollow

4.0

3400

1-1/8" Hollow

FPT Ports Inlet Outlet 1/2" 3/8" 1/2" 3/8" 1/2" 3/8" 1/2" 3/8" 1/2" 3/8" 1/2" 3/8" 1/2" 3/8" 1/2" 3/8" 1/2" 3/8"

Wt./Lbs. 24.0 24.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0

Net Ea. $ 510.00 510.00 620.00 629.00 618.00 699.00 629.00 703.00 723.00

45.0

$ 700.00

Shaft Dia.: 1-1/8" IP TS2011GR2

DULTMEIER SALES • OMAHA, NE

3000

(800) 228-9666

www.dultmeier.com

1/2"

• DAVENPORT, IA

3/8"

(800) 553-6975

E0640


General / InterPump Repair Kits

61

D D

D

General / InterPump Repair Kits

IP K01 Valve Kit

IP K123 Valve Kit

Fits Pump Models: T & TT500 series, T & TT700 series, T & TS800 series, T, TT, & TS900 series, T & TS1000 series (except T1031), T & TS1300 series, T & TS1500T series, T, TS & TT1600 series, TS1711 & TS2000 series, T &TT 9000 series, CW2040, CW3040.

Contents: (6) (6) (6) (6) (6)

90384100 36200366 36200176 94737600 36200251

Part No.

Net Ea.

IP K01

$ 35.85

Contents: (6) 90384100 (6) 36200366 (6) 36200176 (6) 94737600 (6) 36202551 (6) 36711501

O-Ring Valve Seat Valve Plate Spring Valve Guide

IP K201 $ 67.05

Seal Ring Valve Seat Poppet Spring Valve Guide Anti-Extrusion Ring

Net Ea.

IP K43 $ 160.00

Contents: (3) 90162500 Oil Seal

Net Ea.

Oil Seal

Contents: (4) 90358500 O-Ring (3) 96728600 Washer Part No. Net Ea. IP K06 $ 19.55 (3) 90506700 Ring (3) 96728000 Washer (3) 47219566 Screw

IP K149 Ring Kit

Fits Pump Models: T921, TS921, T1321, TS1321, T1621, TS1621, T1631.

Part No.

Net Ea.

IP K2

$ 5.90

Fits Pump Models: T& TS800 series, T &TS921, T & TS1000 series (except T1031), T & TS1311, 1321, 1331, T & TS1511, TS1521, T & TS1621, TS1711, T & TS2011 & 2021, T9121, T9131, T9161, T9211, CW24 & CW2004. (2) 90164800

Fits Pump Models: CW1012, T41, T1031. Net Ea.

IP K62 $ 102.00

O-rings Valve Seat Valve Plate Spring Valve Guide

DULTMEIER SALES • OMAHA, NE

Part No.

Oil Seal

IP K3

Net Ea.

(3) (3)

IP K23 Oil Seal Kit (Piston)

Contents: (3)

90161400

(800) 228-9666

Part No.

Net Ea.

IP K23

$ 15.65

Oil Seal

www.dultmeier.com

47217070 90273000

Intermediate Ring “Long Life” Ring

IP K07 Head Ring Set Fits Pump Models: T811, TS821, T & TS1001, T & TS1011, TS1021, T & TS1311, TS1331, T & TS1511, TS1521, TS1711, T & TS2011, T & TS2021, T2031, T3051,T4031, T9121, T9131, T9161, T9211.

Contents: (6) 47100051

Part No.

Net Ea.

IP K07

$ 10.10

Head Ring

IP K11 Head Ring Kit, 22mm Fits Pump Models: T & TS921, T & TS1321, T & TS1621, T1631 Part No.

$ 13.60

Fits Pump Models: T521, T531, T701, T711, T721, T731, T911, T981, T991, TS1371, TT1411, TT1611, T9721, T9731, T9791, T9951, T9961.

Net Ea.

Contents: IP K149 $ 37.20

IP K3 Oil Seal Kit (Crankshaft)

Contents:

(6) 90385900 (6) 36201266 (6) 36200676 (6) 94739400 (6) 36200851

$ 14.90

IP K06 Bolt Kit

Fits Pump Models: T501, T511, T811, T821, TS821, T921,TS921, T &TS1000 series (except T1031), T & TS 1311, T & TS1321, TS1331, T & TS1511, TS1521, T & TS1621, TS1711, T & TS2011, T & TS2021, T9121, T9131,T9161, T9211, CW2040 / CW3040.

O-Ring Valve Seat Valve Plate Spring Valve Guide Valve Assembly

IP K62 Valve Kit

Net Ea.

IP K83

Part No.

Contents:

Contents:

Part No.

90156500

Part No.

Fits Pump Models: T721, T731, T991, T9731, T9951/61/71, T821, T1021, T & TS921, T & TS1321, T & TS1011, T9131, T & TS2011.

IP K2 Oil Seal Kit (Piston Rod)

IP K43 Valve Kit

Part No.

(3)

IP K943 $ 143.00 O-Ring Valve Seat Valve Spring Valve Guide Valve Unit Backup Ring

(6) 90405900 (6) 36201166 (6) 36201076 (6) 94745000 (6) 36200951 (6) 36706501 (6) 96757000

Fits Pump Models: T61, T81, T121, T151, T1551, T1591.

(6) 90405900 (6) 36201166 (6) 36201076 (6) 94745000 (6) 36200951 (6) 36706501

Contents:

IP K943 Valve Kit

IP K201 Valve Kit (Hi-Temp)

Part No.

Net Ea.

IP K123 $ 43.85

Fits Pump Models: All TT Series Pumps except (1411 & 1611), T9021, T9031, T9041, T9051 & all Box Jet Pumps.

Fits Pump Models: CW1541, CW61 & CW81.

Fits Pump Models: CW2040, CW3040 (Rated to 195° F.) Part No. Net Ea. (6) 90340000 (6) 36200366 (6) 36200176 (6) 94737600 (6) 96200251 (6) 90510500

Part No.

O-Ring Valve Seat Valve Spring Valve Cage Valve

Contents:

Contents:

IP K83 Oil Seal Kit (Piston)

Fits Pump Models: CW2536, CW2542, EZ Series

Contents: IP K11 (3)

46100051

Net Ea.

$ 8.98

Head Ring

IP K21 Head Ring Kit, 20mm Fits Pump Models: T721, T731, T991, T9731, T9951, T9961, T9971.

Contents: (2)

• DAVENPORT, IA

50100051

Part No.

Net Ea.

IP K21

$ 7.59

Head Ring

(800) 553-6975

E0040


General / InterPump Repair Kits IP K29 Packing Assembly, 22 mm

IP K97 Packing Kit

Fits Pump Models: TS921, T921, T & TS1321, T & TS1621, T1631.

Fits Pump Models: All TT Series pumps except (911,1411 & 1611), T9021, T9031, T9041, T9051.

Contents: (1) 90361600 (1) 47080670 (1) 90272500 (1) 46100051 (1) 47217070 (1) 90518200

D

O-rings Packing Retainer Packings Head Rings Intermediate Rings “Long Life” Rings

IP K08 Packing Kit, 20mm Fits Pump Models: T811, TS821, TS1001, T & TS1011, TS1021, T & TS1311, TS1331, T & TS1511, TS1521, TS1711, T9121, T9131, T9161, T9211. Part No. Net Ea. IP K08

$ 37.00

(6) 90270500 Packings

IP K12 Packing Kit, 22mm Fits Pump Models: T501, T511, T921 & TS921, T1321 & TS1321, T & TS1621, T1631. (6) 90272500

Packings

IP K16 Packing Kit, 24mm Contents:

Part No. Net Ea. IP K16 $ 62.95

IP K71 Ring Kit

(3) (3)

IP K19 Packing Kit

(6) 90270300 Packings

Part No. Net Ea. IP K19 $ 33.55

Fits Pump Models: T521, T531, T701, T711, T721, T731, T911, T981, T991, TS1371, T9721, T9731, T9791, T9951, T9961, T9971. Part No. Net Ea. IP K22 $ 13.25

(3) 50080570 Packing Retainers (3) 90361200 O-rings

IP K27 Packing Assembly, 20 mm Fits Pump Models: T521, T531, 701, 711, 721, 731, 911, 981, 991, TS1371, T9721, T9731, T9791, T9951, T9961, T9971.

Contents: (2) 90270300 (1) 50216670 (2) 50.100051 (1) 50080570 (1) 90361200

Part No. Net Ea. IP K71 $ 57.05

Intermediate Ring Restop Ring

Fits Pump Models: CW1012, T1551, T1591

Contents:

Part No. Net Ea. IP K27 $ 20.60

Packings Intermediate Rings Head Rings Packing Retainer O-rings

IP K28 Packing Assembly, 20 mm Fits Pump Models: T811, TS821, T & TS 1001, T & TS1011, TS1021, T & TS1311, TS1331, T & TS1511, TS1521, TS1711, T & TS2011, T & TS2021, T2031, T9121, T9131, T9161, T9211.

DULTMEIER SALES • OMAHA, NE

Part No. Net Ea.

(6) 90277000 Packing IP K113 $ 108.50 (3) 98226500 Ring (3) 90277800 Seal, Low Press.

IP K127 Packing Kit IP K79 Packing Kit Contents:

Fits Pump Models: CW2536, CW2542

Contents:

Part No. Net Ea. IP K79 $ 97.50

(3) 90282800 Ring (3) 90285000 Packing (3) 90285500 Seal, Low Press.

Fits Pump Models: All TT Series pumps except (1411 & 1611), T9021, T9031, T9041, T9051 & all Box Jet Pumps.

Contents:

Part No. Net Ea.

IP K86 $ 17.90 (3) 90360400 O-ring (3) 90383500 O-ring (3) Packing Retainer (Available only in kit form)

IP K22 Packing Retainer Kit

Contents:

47216970 90270400

Part No. Net Ea.

IP K113 Packing Kit

IP K86 Packing Retainer Kit

Fits Pump Models: T521, T531, T701, T711, T721, T731, T911, T981, T991, TS1371, T9721, T9731, T9791, T9951, T9961, T9971.

Contents:

Part No. Net Ea. IP K69 $ 53.80

Contents:

(1) 90361600 O-Ring IP K9101A $ 32.50 (1) 47080970 Low Press Retainer (1) 90270500 High Press Seal (1) 47216970 Ring (1) 47100051 Ring (1) 90270400 Ring (1) 90269400 Low Press Seal

Fits Pump Models: T61, T81, T121, T151

Fits Pump Models: T821, T1021, T1341 (6) 90274500 Packings

IP K9101A Packing Kit

Fits Pump Models: TS1331, TS1711, T9211N, TS1011, TS1511, TS2011-N, TS1021, TS2021-N, TS1041, TS1531

Contents:

Part No. Net Ea. IP K97 $ 15.00

O-Ring O-Ring Head Ring Packing

Fits Pump Models: CW2040, CW3040

(3) 90270400 Ring (3) 90270500 Packing (3) 90271000 Seal, Low Press.

Part No. Net Ea. IP K12 $ 43.30

Contents:

Contents: (3) 90360400 (3) 90383500 (3) 51100051 (3) 90262000

Fits Pump Models: TS1331, TS1711, T9211-N, TS1011, TS1511, TS2011-N, TS1021, TS2021N, TS1041, TS1531

Contents:

Contents:

Part No. Net Ea. IP K29 $ 29.95

IP K69 Packing Kit

Call for InterPump Crossovers

62

Part No. Net Ea.

IP K127 $ 52.75 (3) 90268300 Ring (3) 90268200 Packing (3) 700102 Packing

IP K148 Packing Kit Fits Pump Models: T921, TS921,T1321, TS1321, T1621, TS1621,T1631

Contents:

Part No. Net Ea.

(3) 90272500 Packing IP K148 $ 52.75 (3) 90273000 Ring (3) 90272800 Seal, Low Press.

IP K170 Packing Kit, 20 mm

IP K88 Packing Kit, 15 mm

Fits Pump Models: TSF2019, TSF2021

Fits Pump Models: EZ3040, EZ2542E, EZ2545G, EZ3035G, EZ2545E, EZ2255S, EZ2545S, EZ3040S. Part No. Net Ea.

Part No. Net Ea. IP K170 $ 92.90

Contents:

(3) (3) (3)

90270500 90269400 90270400

IP K88

$ 39.70

High Pressure Seals Low Pressure Seals Restop Rings

IP K96 Packing Assembly

Part No. Net Ea. IP K96 $ 10.85

(1) 90360400 O-ring (1) 90383500 O-ring (1) Head Ring (Available only in kit form) (1) Packing (1) Packing Retainer

Contents:

O-rings Packing Retainer Packings Head Rings Intermediate Rings “Long Life” Rings

(800) 228-9666

www.dultmeier.com

High Pressure Seals Low Pressure Seals

Fits Pump Models: CW24, CW2040, CW3040. Part No. Net Ea. IP K969 $ 55.50

Contents: (3) (3) (3)

90270500 90269400 90270400

High Pressure Seals Low Pressure Seals Restop Rings

IP 100564 Packing Kit, 36 mm

Part No. Net Ea. IP K28 $ 27.80

(1) 90361600 (1) 47080570 (1) 90270500 (1) 47100051 (1) 47216670 (1) 90518200

90269200 90269000

IP K969 Packing Kit, 20 mm

Fits Pump Models: All TT Series pumps except (1411 & 1611), T9021, T9031, T9041, T9051.

Contents:

Contents: (3) (3)

Fits Pump Models: CW1541 Part No. Net Ea. IP 100564 $ 195.00

Contents: (6) (6) (6)

• DAVENPORT, IA

90282300 90282000 90281800

Packing, Low Pressure Packing, High Pressure Restop Rings

(800) 553-6975

E0041


Plunger Pumps

63

Udor Plunger Pumps are widely used in pressure wash, truck wash, car wash and industrial cleaning applications. Available in a wide variety of pressures and flow rates. Designed for pulley drive, direct electric motor drive, direct engine drive, gear box engine drive and hydraulic motor drive. Standard Features Include: Brass manifolds • Heat treated crankshafts • Stainless steel check valves and piston guides • Industrial quality ball bearing or needle bearings • Solid ceramic plungers • Heavy duty high pressure seals • Rated to 160˚ F. (Note: rails are not included and must be ordered separately if needed.) Right hand shafts are standard. Specify if left hand shaft is required.

D

MD4030U

Direct Drive Motor Models Part No. Flow/Pressure RPM Flange UD PND3020Z 3.0 @ 2000 1750 56C UD PNL3020Z 3.0 @ 2000 3400 56C UD PND4015Z 4.0 @ 1750 1750 56C UD MD4030U 4.0 @ 3000 1750 182/184TC

Shaft 5/8" Hollow 5/8” Hollow 5/8” Hollow 1-1/8” Hollow

Wt. 13 lbs. 13 lbs. 13 lbs. 26 lbs.

Net Ea. $ 274.50 274.50 280.00 385.00

Direct Drive Engine Models Part No. Flow/Pressure RPM Flange UD PNL3025T 3.0 @ 2500 3400 Gas UD ML4030W 4.0 @ 3000 3400 Gas UD MC1520GR 4.0 @ 3000 3400 Gear Box UD MKL4040W 4.0 @ 4000 3400 Gas UD MKC1528GR 4.0 @ 4000 3400 Gear Box UD GKC1735GR 4.5 @ 5000 3400 Gear Box UD MKL5035W 5.0 @ 3500 3400 Gas UD MKC1824GR 5.0 @ 3500 3400 Gear Box UD GKC2135GR 5.5 @ 5000 3400 Gear Box

Shaft 3/4" Hollow 1” Hollow 1” Hollow 1” Hollow 1” Hollow 1” Hollow 1” Hollow 1” Hollow 1” Hollow

Wt. 14 lbs. 25 lbs. 33 lbs. 28 lbs. 37 lbs. 52 lbs. 37 lbs. 37 lbs. 52 lbs.

Net Ea. $ 279.00 342.50 547.00 410.50 591.00 1082.00 434.00 617.00 1098.00

Pulley Drive Models Part No. Flow/Pressure RPM Flange Shaft Wt. UD PNC1315S 3.5 @ 2000 1450 None 24mm 12 lbs. UD MC1520S 4.0 @ 3000 1450 None 24mm 23 lbs. UD MKC1528S 4.0 @ 4000 1450 None 24mm 27 lbs. UD GHC1650S 4.2 @ 7300 1450 None 24mm 55 lbs. UD GKC1735S 4.5 @ 5000 1450 None 24mm 42 lbs. UD MC1820S 5.0 @ 3000 1450 None 24mm 23 lbs. UD MKC2024S 5.5 @ 3500 1450 None 24mm 27 lbs. UD GKC1940S 5.0 @ 5800 1450 None 24mm 43 lbs. UD GC3017S 8.0 @ 2500 1450 None 24mm 36 lbs. UD GC3815S 10 @ 2200 1450 None 24mm 36 lbs. UD GKC5012S 12.5 @ 2000 1450 None 24mm 39 lbs. UD NX55/200 14 @ 3000 1450 None 35mm 75 lbs. UD NX75/150 20 @ 2200 1450 None 35mm 75 lbs. UD VX130/160 33 @ 2500 1450 None 35mm 160 lbs. UD VX160/130 40 @ 2000 1450 None 35mm 160 lbs. UD 8702.10 Rail Kit, P/M/MK Series........................................................................ UD 8702.08 Rail Kit, G Series.................................................................................. UD 8702.30 Rail Kit, VX Series................................................................................ UD 8702.35 Rail Kit, NX Series...............................................................................

Net Ea. $ 274.50 354.50 411.00 1588.00 904.00 378.00 448.00 1130.00 569.00 639.00 781.00 2698.00 2698.00 4484.00 4484.00 7.58 8.21 62.45 62.45

D

ML4030W

D

PNC1315S

D

Hydraulic Drive Pump/Motor Units Part No. Pump Output Hydraulic Requirements UD MD4030SH 4.0 @ 3000 12 GPM @ 1500 PSI UD MKD4040SH 4.0 @ 4000 12 GPM @ 2000 PSI UD GKC3817SH 10 @ 2500 20 GPM @ 2200 PSI UD GKC3820SH 10 @ 3000 20 GPM @ 2400 PSI

Wt. 36 lbs. 39 lbs. 75 lbs. 75 lbs.

Net Ea. $ 1035.00 1114.00 1802.00 1802.00

MD4030SH

Repair Kits Part No. Description UD UD1 Valve Kit, PN Series......................................................................................... UD UD2 Valve Kit, MC/MD Series.................................................................................. UD UD3 Valve Kit, GC/GD Series.................................................................................. UD UD30 Valve Kit, MK Series......................................................................................... UD UD31 Valve Kit, GKC Series...................................................................................... UD UD7 Seal Kit, PND/PNL, 15mm............................................................................... UD UD8 Seal Kit, PND/PNL, 18mm.............................................................................. UD UD9 Seal Kit, GK/MK, 20mm................................................................................... UD UD10 Seal Kit, GC/GD/GK Series.............................................................................. UD UD12 Seal Kit, GC/GKC Series................................................................................. UD UD28 Seal Kit, MC/ML Series....................................................................................

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

Net Ea. $ 49.95 52.05 59.40 55.45 61.80 57.60 59.65 61.75 63.10 67.10 59.65

E0713


Plunger Pumps

64

High Quality, Japanese-Made Plunger Pumps. Long life, quiet and efficient design. Liquid cooled, low drag seals mean these pumps can run dry longer without damage. Stainless steel valves, precision ground ceramic plungers, forged brass heads and oversized crankshaft bearings are all standard features. Available in low RPM pulley drive or higher speed, direct drive RPM models. Flows from 3.7 gpm to 36 gpm and pressures from 1500 to 2300 psi. Standard seals will handle temperatures to 175˚F. Note: Pump rails are not included and must be ordered separately except on 1110.

Pulley Drive Design (Specify L or R for left or right hand shaft)

Max. Max. Wt. Part No. Flow PSI RPM Inlet Outlet Shaft Lbs. Net Ea. AJ 313 4.0/5.0 1500 1050/1450 1/2” 3/8” 18mm 17 $ 575.00 AJ 516 4.0/5.0 2300/2000 950/1200 1/2” 3/8” 22mm 21 759.00 AJ 511 6.0 1500 950 1/2” 3/8” 22mm 21 649.00 AJ 508 10 1200 1200 3/4” 1/2” 22mm 21 749.00 AJ 713KVR 10 1800 900 3/4” 1/2” 28mm 33 1875.00 AJ 709 15 1100 950 3/4” 1/2” 28mm 33 1375.00 AJ 1110 * 16/23 1500/1000 650/950 1-1/4” 1” 38mm 86 3692.00 AJ 3615 36 1500 800 1-1/2” 1” 35mm 125 4598.00 * Mounting feet are included with this model. Double shaft is standard.

D

313

Direct Drive Design (Specify L or R for left or right hand shaft)

Part No. AJ 309 AJ 312

Max. Flow 3.7 5.0

Max. PSI 1500 1500

RPM 1725 1725

Inlet 1/2” 1/2”

Outlet 3/8” 3/8”

Shaft 24mm 24mm

Wt./Lbs. 17 17

Net Ea. $ 599.00 698.00

Pump Rails Part No.

D

AJ 30102 AJ 30115 AJ 30109 AJ 30131

508

Net Ea.

Short single rail for models 3 & 5 Series Pumps (2 required)........ $ 17.45 High rail set - 5 Series.................................................................... 57.95 Rail set, 7 Series Pumps (1 required)............................................ 71.65 Rail set, 3615................................................................................. 160.00

D

3615

Repair Kits Seal Kits Part No.

AJ 30114 AJ 30100 AJ 30120 AJ 30110 AJ 30121 AJ 30105 AJ 30117

Seal Kit, 3 series pumps................................................................ Seal Kit, 516 pump......................................................................... Seal Kit, 511 pump......................................................................... Seal Kit, 508 Pump........................................................................ Seal Kit, 713 Pump........................................................................ Seal Kit, 709 Pump........................................................................ Seal Kit, 1110 Pump......................................................................

Net Ea. $ 97.05 104.50 126.00 120.00 126.00 113.50 394.50

D

Valve Kits

709

D

Part No.

Net Ea.

AJ 30108 AJ 30101 AJ 30111 AJ 30112 AJ 30106 AJ 30116 AJ 30118 AJ 30119

$ 93.70 128.50 188.50 165.00 207.00 200.50 678.00 736.00

Valve Kit, 3 Series Pumps, 3 Valves............................................... Valve Kit, 516 Pump, 3 Valves........................................................ Inlet Valve Kit, 508/511/713 Pumps................................................ Outlet Valve Kit, 508/511/713 Pumps............................................. Inlet Valve Kit, 709 Pump............................................................... Outlet Valve Kit, 709 Pump............................................................. Inlet Valve Kit, 1110 Pump............................................................. Outlet Valve Kit, 1110 Pump...........................................................

1110

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0709


Piston & Plunger Pumps

65

Hypro 2300B-P Series Plunger Pumps

2200 Series

Hypro Twin Cylinder Ceramic Plunger Pumps Now you can have an American made, brass head, ceramic pump at a competitive price. Crankshaft roller bearings run in an oil bath for continuous protection. Ceramic plungers for long life and smooth operation. Stainless steel valve assemblies. Brass manifold head. Onepiece connecting rod and floating wrist pin. Full 2-Year Warranty for defects in material and workmanship. Available with either a solid or hollow shaft. Also available in either 1725 or 3450 RPM for direct hook-up to electric or gasoline engine.

• • • • • • • •

D

Part No. RPM Shaft GPM PSI

2.1 2.1 2.1 2.1 3.0 3.0 3.0 3.0

D D

Polished ceramic plungers for longer seal life. Single-piece forged brass head. Precision machined, unitized valves. Operates at pressures to 3000 PSI. High temperature U-cup seal is extra wear resistant and can be replaced in minutes. Oil bath crankcase. TWO YEAR Warranty against defects in material or workmanship.

Note: Solid shafts are 3/4", hollow shafts are 5/8". 1/2” FPT inlet and 3/8” outlet. Shaft rotation is either CW or CCW.

HY 2220B 1725 Solid HY 2220BH 1725 Hollow HY 2221B 3450 Solid HY 2221BH 3450 Hollow HY 2230B 1725 Solid HY 2230BH 1725 Hollow HY 2231B 3450 Solid HY 2231BH 3450 Hollow

Stainless Steel Unitized Valves Forged Brass Head Polished Ceramic Plungers Buna-N High Temperature Seals Forged Steel Crankshaft Oil Bath Crankcase One Piece Connecting Rod & Patented Floating Wrist Pin Heavy Duty Needle Bearings Support Both Ends of Crankshaft

Required H.P.

2000 2000 1500 1500 1500 1500 1500 1500

Net Ea.

$ 343.50 354.00 343.50 354.00 343.50 354.00 343.50 354.00

3 3 2 2 3 3 3 3

SPECIFICATIONS: Shaft size 3/4” • Two 1/2" inlet ports and two 3/8" outlet ports • Either CW or CCW rotation; • Maximum temperature 180° F. • Maximum inlet pressure is 60 PSI. • These pumps can be mounted to various C-Face motors. • Pump includes mounting rails. Note: 8000-10 Flange kit is used to mount pumps to C-Face motors. Part No. Max. GPM Max. PSI Max. RPM HY 2304BP * 4.2 1200 1725 HY 2314BP * 4.0/3.0 1200 1450/1100 HY 2330B 3.1 2500 1725 HY 2340B 4.2 2500 1725 HY 2345B 4.8 2500 1725 HY 2351B 4.0 3000 1725 HY 2359B 3.5 3000 1725 * Car Wash Pumps with heavy-duty seals. HY 8000-3 HY 8000-10 HY 8000-21

5300 Series Twin Piston Pumps

Shaft 3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4"

Wt. 15 lbs. 15 lbs. 16 lbs. 16 lbs. 16 lbs. 16 lbs. 15 lbs.

2300 Series Pump Accessories Flange Kit for 56C & 143TC/145TC C-Face Motors....................... Flange Kit for 182TC/184TC C-Face Motors.................................. 2:1 Ratio Gearbox for 8 to 18 HP Gas Engines w/ 1" solid shafts..

Net Ea. $ 474.50 474.50 457.50 455.50 450.00 467.50 430.00

$ 50.60 88.80 795.00

1/2” FPT Ports

Big Twin Series 5200

Rated at Pressures to 500 PSI. These pumps use a high quality cast iron housing and incorporate unitized stainless steel valves, needle bearing crank pin and large ball bearings to support the crankshaft. Crankshafts are available in a 5/8" solid shaft, for pulley or coupling drive and a 5/8" hollow shaft version for direct mounting to a standard 56 frame, 5/8" motor shaft. Piston cups are available in rubber, for water, soaps and detergents to 140° F. Teflon cups are recommended for temperatures above 140° F. 1/2” FPT ports. Part No.

GPM @ Required HP 1800 RPM @ 500 PSI

HY 5320CR HY 5320CC HY 5330CR HY 5330CC HY 5315CHR HY 5320CHR HY 5320CCH HY 5330CHR HY 5330CCH

2.0 2.0 3.0 3.0 1.5 2.0 2.0 3.0 3.0

.80 .80 1.10 1.10 .67 .80 .80 1.10 1.10

3/4” FPT Ports

D

Shaft Type

Piston Cups

5/8" Solid 5/8" Solid 5/8" Solid 5/8" Solid 5/8" Hollow 5/8" Hollow 5/8" Hollow 5/8" Hollow 5/8" Hollow

Rubber Teflon Rubber Teflon Rubber Rubber Teflon Rubber Teflon

Net Ea.

D

$ 266.00 284.00 266.00 284.00 266.00 266.00 284.00 266.00 284.00

Mounting Rails are Included

Part No. GPM HY 5206C 6 HY 5206CF 6 HY 5206CH 6 HY 5206CFH 6 HY 5210C 10 HY 5210CF 10 HY 5210CH 10 HY 5210CFH 10

5322 Series 1/2” FPT Ports

D

Rated at Pressures to 1000 PSI & 2.2 GPM at 1800 RPM (1.5 HP)

Shaft

Cups

Wt.

(800) 228-9666

Net Ea. $ 465.50 473.00 465.50 473.00 465.50 473.00 465.50 473.00

Pump Lubricant Oil from Hypro. Specially formulated, multi-weight oil with special added agents. Reduces wear in piston, plunger and diaphragm pumps. Provides smooth pump operation in a variety of temperatures. SAE 10W30 Non-detergent oil is sold in 1 quart bottles. Size

*Std. Pack

HY 2160-38 1-Quart 12 HY 2160-47 1-Gallon -

Net Ea.

HY 5322C 5/8"-Solid Rubber 10 lbs. $ 286.00 HY 5322CH 5/8"-Hollow Rubber 10 lbs. 286.00 DULTMEIER SALES • OMAHA, NE

Shaft Size Piston Cups 1" Solid Leather 1" Solid Fabric 1-3/8" Hollow Leather 1-3/8" Hollow Fabric 1" Solid Leather 1" Solid Fabric 1-3/8" Hollow Leather 1-3/8" Hollow Fabric

Pump Oil

Cast iron housings, heavy duty ball bearings, stainless steel plungers and unitized stainless steel valves. Crankshafts are available in a 5/8" solid shaft, for pulley or coupling drive and a 5/8" hollow shaft version for direct mounting to a standard 56 frame, 5/8" motor shaft. 1/2” FPT ports. Note: 5322 pumps are standard with ceramic plungers for increased wear life.

Part No. Part No.

Deliver volume and high pressure for efficient cleaning or spraying. Rated to 140° F. These pumps are available with Fabric Cups for insecticides and herbicides; Leather Cups for aromatic solvents and other liquids injurious to rubber. 3/4” FPT ports. (Buna Cups are also available.)

Net Ea.

$ 10.00 31.85

D

*10% Discount for Orders in Standard Packages. •

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0047


Plunger Pumps Powerline™ 2400B Plunger Pumps Hypro's PowerLine™ solid shaft plunger pumps are designed to be used in belt drive or direct coupled operations where the power source is an electric motor or gas engine. These brass head, triplex pumps are equipped with self-loading seals and operate at temperatures to 160° F. Standard Features: Stainless steel unitized valves • Polished ceramic plungers • Forged brass head • Oil-bath crankcase • One-piece connecting rod • Floating wrist pin • Heavy duty roller bearings • Mounting rails are also standard. 5-Year Warranty

66

Model 2535S Plunger Pump From Hypro! Large Volume Plunger Pump with Stainless Steel manifold. Ideal for automatic car washes, plant wash down, tunnel washes. 316SS Stainless manifold is standard. Longest warranty in the industry at 5 years. Innovative design allows for easy servicing of valves and seals. Standard Features: Stainless steel valves • Oversize crankshaft • Bronze connecting rods • Ceramic plungers • Epoxy coated finish • Inlet ports are 1-1/2" FPT • Outlet ports are 1" FPT • Shaft size is 35MM.

5-Year Warranty

D D

D

HY 2430B

HY 2535S

Part No. Max. PSI Max. GPM Max. RPM Wt. Net Ea. HY 2430B 3600 4.3 1725 35 lbs. $ 865.00 HY 2431B 3600 5.1 1725 35 lbs. 798.00 HY 2432B 3600 5.9 1725 35 lbs. 798.00 HY 2434B 2500 7.9 1725 35 lbs. 798.00

Plunger Pump Part No.

HY 2535S HY 2545S

Max. Flow

Max. PSI

Max. RPM

Wt.

38 GPM 47 GPM

1500 1200

800 800

140 lbs. 140 lbs.

Net Ea.

$ 3447.00 3609.00

REPAIR KITS

Specifications: Inlet ports: Two 3/4" FPT • Outlet ports: Two 1/2" FPT • Shaft rotation: CW or CCW • Shaft size: 1" solid • Oil type: 30 Wt. nondetergent • Oil capacity: 26 oz. • Maximum water temperature: 160˚ F. • Maximum water inlet pressure: 60 PSI. Valve Kits D

D

D

HY 2410B

Ceramic Plunger Kits

Wt. Part No. Max. PSI Max. GPM Max. RPM Lbs. Net Ea. HY 2410B 2500 4.4 1725 41 $ 737.00 HY 2411B 2500 5.3 1725 41 679.00 HY 2412B 2500 5.9 / 4.0 1725 / 1100 41 669.00 HY 2412B-C3 * 2500 5.9 1725 41 679.00 HY 2413B 1800 7.2 1725 41 679.00 HY 2414B 1800 8.0 / 4.0 1725 / 900 41 669.00 HY 2414B-L ** 1800 8.0 / 4.0 1725 / 900 41 669.00 * Standard with rails to match “Cat 310” mounting. ** Left Hand Shaft HY 8000-15 HY 8000-21 HY 8000-17 HY 8000-18

Seal Kits

400 Series Gearbox & Flange Accessories 2 Net Ea. Gearbox for Gas Engines with 1-1/8" Shafts...... $ 487.00 Gearbox for Gas Engines with 1" Shafts........... 795.00 Flange for C-Face Nema 213TC/215TC Motors 115.00 Flange for C-Face Nema 182/184C Motors....... 112.50 NOTE: Shafts are Right-Hand when facing pump.

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

Part No. HY 3430-491 HY 3430-316

Description Net Ea. Valve Kit, 2300 B&P Series..................................... $ 46.50 Valve Kit, 2400 B&P Series.................................... 74.90

HY 3430-271 HY 3430-0493 HY 3430-306 HY 3430-485 HY 3430-486

Seal Kit, 2300 B Series........................................... Seal Kit, 2300 P Series........................................... Seal Kit, 2410/11/12 B Series................................. Seal Kit, 2410/11/12/12/30/31/32 P Series............. Seal Kit, 2413/14/33/34 P Series............................

43.80 46.80 39.70 40.30 37.45

HY 3430-320 HY 3430-0514 HY 3430-321 HY 3430-322

Ceramic Plunger Kit, 2300 B Series...................... Ceramic Plunger Kit, 2300 P Series...................... Ceramic Plunger Kit, 2410/11/12 B&P Series....... Ceramic Plunger Kit, 2413/14/33/34 B&P Series..

23.40 19.05 38.50 41.95

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0046


Plunger Pumps

67

High Quality Plunger Pumps from Comet. All Pumps Feature the following: Anodized, Die-Cast Aluminum Crankcase • Solid Ceramic Plungers • Stainless Steel Check Valves and Piston Guides • Buna V-Packings • Reversible Crankcase Design for Right or Left Hand Mounting • Designed for Direct Drive to Gas Engines or Electric Motors or with Solid Shafts for Belt Drive.

D

AXD2020E with unloader

D

LWD3025G

Direct Drive Motor Models Part No. Flow/Pressure RPM Flange Shaft MV AXS2015E *1.70 gpm @ 1500 PSI 1750 56C 5/8” Hollow MV AXD2020E *1.90 gpm @ 2000 PSI 3400 56C 5/8” Hollow MV BXD2020E *1.90 gpm @ 2000 PSI 3400 56C 5/8” Hollow MV LWD2020E 2.10 gpm @ 2000 PSI 3400 56C 5/8” Hollow MV BXD2520E *2.50 gpm @ 2000 PSI 3400 56C 5/8” Hollow MV AXD2527GE *2.50 gpm @ 2700 PSI 3400 56C 3/4” Hollow MV BXD3020E *2.80 gpm @ 2000 PSI 3400 56C 5/8” Hollow MV LWD3020E 3.0 gpm @ 2000 PSI 3400 56C 5/8” Hollow MV LWD3522E 3.5 gpm @ 2200 PSI 3400 56C 5/8” Hollow MV LWD3522GE 3.5 gpm @ 2200 PSI 3400 56C 3/4” Hollow MV FWS3030E 3.0 gpm @ 3000 PSI 1750 182/184TC 1-1/8” Hollow MV FWS3530E 3.5 gpm @ 3000 PSI 1750 182/184TC 1-1/8” Hollow MV FWS4030E 3.9 gpm @ 3000 PSI 1750 182/184TC 1-1/8” Hollow MV FWS4530E 4.5 gpm @ 3000 PSI 1750 182/184TC 1-1/8” Hollow * Includes Unloader Valve & Chemical Injector.

Wt. Lbs. 12 lbs. 12 lbs. 11 lbs. 13 lbs. 11 lbs. 12 lbs. 11 lbs. 13 lbs. 13 lbs. 13 lbs. 20 lbs. 20 lbs. 20 lbs. 20 lbs.

Net Ea. $ 239.50 250.00 192.00 283.50 192.00 269.50 192.00 283.50 335.50 335.50 463.00 465.00 465.00 465.00

Direct Drive Engine Models

Wt. Lbs. 13 lbs. 11 lbs. 12 lbs. 12 lbs. 11 lbs. 13 lbs. 14 lbs. 13 lbs. 13 lbs. 18 lbs. 30 lbs. 20 lbs. 31 lbs. 20 lbs.

Net Ea. $ 266.00 192.00 260.50 249.50 204.00 276.00 253.50 271.50 336.00 382.00 638.00 486.00 679.00 486.00

Wt. Lbs. 13 lbs. 13 lbs. 13 lbs. 13 lbs. 13 lbs. 13 lbs. 19 lbs. 27 lbs. 27 lbs. 20 lbs. 45 lbs. 27 lbs. 45 lbs. 27 lbs. 27 lbs. 45 lbs. 45 lbs. 45 lbs. 45 lbs.

Net Ea. $ 278.00 278.00 278.00 278.00 296.50 296.50 442.00 484.00 461.00 496.00 792.00 486.00 792.00 498.50 506.00 749.00 746.00 796.00 826.00

Part No. Flow/Pressure MV LWD2020G 2.1 gpm @ 2000 PSI MV BXD2220G *2.2 gpm @ 2000 PSI MV AXD2527G *2.5 gpm @ 2700 PSI MV AXD3020G *2.7 gpm @ 2000 PSI MV BXD3025G *2.8 gpm @ 2500 PSI MV LWD3025G *3.0 gpm @ 2500 PSI MV BWD3027G *3.0 gpm @ 2700 PSI MV AWD4030G 4.0 gpm @ 3000 PSI MV AWD4036GK *4.0 gpm @ 3600 PSI MV ZWD4040G 4.0 gpm @ 4000 PSI MV FW4030SGR 4.2 gpm @ 3000 PSI MV HWD4540G 4.4 gpm @ 4000 PSI MV HW4540SGR 4.8 gpm @ 4000 PSI MV HWD5540G 5.3 gpm @ 4000 PSI * Includes Unloader Valve & Chemical Injector.

RPM 3400 3400 3400 3400 3400 3400 3400 3400 3400 3400 3400 3400 3400 3400

Flange Gas Gas Gas Gas Gas Gas Gas Gas Gas Gas Gas Gas Gas Gas

Shaft 3/4” Hollow 3/4” Hollow 3/4” Hollow 3/4” Hollow 3/4” Hollow 3/4” Hollow 3/4” Hollow 1” Hollow 1” Hollow 1” Hollow Gear Box 1” Hollow Gear Box 1” Hollow

Pulley/Belt Drive Models

D

RW6030S

Part No. MV LW1009S MV LW1509S MV LW3020S MV LWS-3020S MV LW3525S MV LWS-4020S MV FW4030S MV RWS4040S MV RWS5030S MV FWS5040S MV TW5050S MV RW5535S MV TW5550S MV RW6030S MV RWS6040S MV TWN-8025S MV TWS8035S MV TWS-10030S MV TWS-13020S

Flow/Pressure 1.0 gpm @ 1500 psi 1.5 gpm @ 1500 psi 3.0 gpm @ 2000 psi 3.1 gpm @ 2000 psi 3.5 gpm @ 2500 psi 4.0 gpm @ 2000 psi 4.0 gpm @ 3000 psi 4.0 gpm @ 4000 psi 4.9 gpm @ 3000 psi 5.2 gpm @ 4000 psi 5.2 gpm @ 5000 psi 5.5 gpm @ 3500 psi 5.8 gpm @ 5000 psi 6.2 gpm @ 3000 psi 6.0 gpm @ 4000 psi 8.0 gpm @ 2500 psi 8.3 gpm @ 3500 psi 10.7 gpm @ 3000 psi 13.0 gpm @ 2000 psi

REPAIR KITS

D

LWS3020S

(800) 228-9666

Flange None None None None None None None None None None None None None None None None None None None

Shaft 24mm 24mm 24mm 24mm 24mm 24mm 24mm 24mm 24mm 24mm 24mm 24mm 24mm 24mm 24mm 24mm 24mm 24mm 24mm

Part No. MV 5019.0667 MV 5019.0671 MV 5019-77 MV 5019-78 MV 5019-35 MV 5019-37 MV 5019-64 MV 5019-38 MV 5025-0014 MV 5025-0030 MV 5025-11 MV 5025-0020 MV 5025-0021

DULTMEIER SALES • OMAHA, NE

RPM 1450 1450 1450 1750 1450 1750 1450 1750 1750 1750 1450 1450 1450 1450 1750 1000 1750 1750 1750

Net Ea. Packing Seal Kit, BXD Gas Models......................................................... $ 39.45 Packing Seal Kit, BXD Electric Models.................................................... 39.75 Packing Seal Kit, AXD/AXS 2000 PSI Models......................................... 41.95 Packing Seal Kit, AXD 2500 PSI Models................................................. 56.70 Packing Seal Kit, LW Pumps, 15mm....................................................... 39.70 Packing Seal Kit, LW Pumps, 18mm....................................................... 45.60 Packing Seal Kit, ZWD Pumps, 15mm.................................................... 45.45 Packing Seal Kit, ZWD Pumps, 18mm.................................................... 87.90 Valve Kit, AXD/AXS/GXD Pumps............................................................ 33.60 Valve Kit, BWD/AWD Pumps................................................................... 34.80 Valve Kit, LW/ZW/FW/HW/SW Pumps..................................................... 50.75 Valve Kit, TW Pumps up to 3600 PSI...................................................... 76.70 Valve Kit, TW Pumps up to 4000 PSI & Up............................................. 91.95

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0790


Plunger Pumps

68

Triplex Plunger Pumps from Giant Industries. Designed for pulley drive or direct-drive applications. Ideal for Car wash, Pressure Wash, Sewer Cleaning, Reverse Osmosis, Water Blasting and many more. All pumps feature a 5-Year Warranty in car wash and pressure wash applications. Lifetime warranty on manifolds due to erosion or freezing.

D D

D

P56W

P220A

LP123A

Standard Features: Forged crankshafts • Tapered roller bearings • Bronze connecting rods • Ceramic plungers • Brass or Aluminum/Bronze fluid ends • Corrosion-resistant Hastelloy valves • Stainless steel and brass wetted parts • Rated to 160° F. (or 195° F. as noted), higher temperature seals are available • Die Cast Aluminum crankcases. (Note: Rail kits are shown, but must be ordered separately if needed. Also, pumps have female NPT ports unless noted. BSP thread adapters are available if required). Flows to 5-1/2 GPM Part No. GPM PSI

D

GU P205 0.5 GU P208 1.0 GU P209 1.5 GU P221 2.3 GU P221-30 † 2.3 GU P224 2.8 GU P223 3.0 GU P218A 3.4 GU P340 3.5 GU P313 3.8 GU P460 3.8 GU P46W * 3.9 GU P219 4.2 GU P219-30 † 4.2 GU P54W * 4.5 GU P220A 4.7 GU P316 4.7 GU P317 4.8 GU P55W * 4.9 GU P322 5.0 GU P58W * 5.0 GU P325 5.2 GU P485 * 5.3 GU P318 5.5 GU P455A 5.5

SP100W

D

LP301A

2000 2000 2000 2000 2000 3000 2000 2500 4000 3500 7250 2175 2500 2000 4000 2000 3000 3000 2300 3000 3500 3500 7250 2000 5000

RPM

Shaft

Inlet

Outlet

1750 1750 1750 1750 1750 1750 1750 1750 1750 3450 1450 1420 1750 1750 1450 1750 1750 1750 1420 1750 1450 3450 1450 1450 1450

24mm 24mm 24mm 24mm 24mm 24mm 24mm 24mm 24mm 24mm 28mm 18mm 24mm 24mm 24mm 24mm 24mm 24mm 24mm 24mm 24mm 24mm 28mm 24mm 28mm

1/2" 1/2” 1/2” 1/2” 1/2”BSP 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” BSP 1/2” 1/2”BSP 1/2” BSP 1/2” 1/2” 1/2” 1/2” BSP 1/2” 1/2” BSP 1/2” 1/2” BSP 1/2” 1/2”

3/8" 3/8” 3/8” 3/8” 3/8”BSP 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” 3/8” BSP 3/8” 3/8”BSP 3/8” BSP 3/8” 3/8” 3/8” 3/8” BSP 3/8” 3/8” BSP 3/8” 3/8” BSP 3/8” 3/8”

RPM

Shaft

Inlet

Outlet

**Rail Kit

1161 1161 1161 1161 1161 1161 1161 1161 1161 1161 7358 1075 1161 1161 1075 1161 1161 1161 1075 1161 1075 1161 7358 1161 7358

Wt.

12 lbs. 12 lbs. 12 lbs. 12 lbs. 12 lbs. 12 lbs. 12 lbs. 12 lbs. 16 lbs. 16 lbs. 37 lbs. 16 lbs. 12 lbs. 12 lbs. 18 lbs. 12 lbs. 16 lbs. 16 lbs. 18 lbs. 16 lbs. 19 lbs. 16 lbs. 42 lbs. 16 lbs. 37 lbs.

Net Ea.

$ 379.00 379.00 379.00 379.00 579.00 379.00 379.00 379.00 469.00 398.00 4595.00 529.00 379.00 589.00 769.00 379.00 396.00 399.00 635.00 409.00 769.00 405.00 3848.00 459.00 1295.00

Flows Over 6 GPM Part No. GPM PSI

Giant Pump Oil

D

D

Special blend crankcase oil/lubricants for Giant Pumps. Model 1060-32 is for use in GX/HR/P200/P300/P400 and SP Series pumps and is sold in 32 oz. bottles. Model 1154 is a different oil blend and is for use in MP/LP/GP Pumps, sold in 1-gallon containers. Part No.

GU 1060-32 GU 1154

Size

Net Ea.

32 oz. $ 10.30 1 Gallon 41.80

DULTMEIER SALES • OMAHA, NE

**Rail Kit

Wt.

GU P56W 6.1 1900 1420 24mm 1/2" 3/8" 1075 18 lbs. GU P435 6.6 3625 1450 28mm 3/4” 1/2” 7358 37 lbs. GU P59 7.5 1900 1450 24mm 1/2” 3/8” 1075 19 lbs. GU LP700 7.9 7250 1000 35mm 3/4” 1/2” 7357 116 lbs. GU P423R 8.3 2600 1450 28mm 1” 3/4” 7358 37 lbs. GU LP600 * 9.7 6000 1000 35mm 1-1/4” BSP 1” BSP 7357 110 lbs. GU P422R 10 2000 1450 28mm 1” 3/4” 7357 37 lbs. GU SP100W 11 1900 1420 28mm 3/4” 1/2” 7358 31 lbs. GU MP4124 13 2600 1420 28mm 1” 3/4” 7358 72 lbs. GU P420A 13 1700 1460 28mm 1” 3/4” 7357 37 lbs. GU GP6124 13 5800 800 42mm 1-1/2” 1” Included 309 lbs. GU LP301A * 14 4000 1000 35mm 1-1/4” BSP 1” BSP 7357 110 lbs. GU P470 * 18 1000 1450 30mm 1” BSP 3/4” BSP 7358 39 lbs. GU LP200 20 2900 1000 35mm 1-1/2” BSP 1” BSP 7357 112 lbs. GU P536 26 1750 1450 36mm 1” BST 3/4” BSP 7358 93 lbs. GU LP123A 35 1300 800 35mm 1-1/2” 1” 7357 116 lbs. ** Rail kits not included. * BSP is British Pipe Thread, adapters to NPT thread are available if needed. † Rated to 195° F. SERVICE & REPAIRS Part No.

RAIL KITS

Net Ea.

GU 1075 Rail Kit....................... $ 21.75 GU 1161 Rail Kit....................... 21.50 GU 7357 Rail Kit....................... 123.50 GU 7358 Rail Kit....................... 27.60

(800) 228-9666

www.dultmeier.com

Net Ea.

$ 649.00 1295.00 779.00 12995.00 1225.00 7975.00 1225.00 1298.00 4891.00 1229.00 18182.00 7497.00 1675.00 7575.00 2360.00 3498.00

Did you know? We can service almost every brand of pump we sell in our catalog. Call us at 1-800-228-9666 (Omaha, NE) for a quote!

• DAVENPORT, IA

(800) 553-6975

E0043


REPAIR KITS

69

Valve, Plunger Packing, Oil Seal & Seal REPAIR KITS D

D

D

PLUNGER PACKING KITS #09164 PLUNGER PACKING KIT for P217 / P218 / P219 / P220 / P221 / P227 & P230 Series Pumps (3) (3) (3)

VALVE KITS #09116 VALVE ASSEMBLY KIT for P200 & P300 Series Pumps (6) 07946 Valve Assembly, Complete (6) 07853 O-Ring

#09143 VALVE ASSEMBLY KIT for P420 / P422 / P423 & P425 Series Pumps (6) 08408 Valve Assembly, Complete (6) 07214 O-Ring

#09039 VALVE ASSEMBLY KIT for P46W & P46W-HK Series Pumps (3) (3) (3) (3) (3) (3) (3) (3)

07325 06017-0100 06016 06014 06015 07234 12004 07035

Spring Retainer Valve Spring Valve Plate Valve Seat O-Ring, Valve Seat O-Ring, Adapter O-Ring, Manifold Plug O-Ring, Discharge Plug

#09041 VALVE ASSEMBLY KIT for P55W / P56W / P56W-HK Series Pumps (3) 07325 (3) 06017-0100 (3) 06016 (3) 06014 (3) 06015 (3) 07212 (3) 07214 (3) 07035

Retainer, Valve Spring Valve Spring Valve Plate Valve Seat O-Ring, Valve Seat O-Ring, Adapter (Inlet Only) O-Ring, Inlet Plug O-Ring, Discharge Plug

08477 08087 07904

(6) (3) (3)

07374 07375 06267

Valve Spring Valve Cone (Outlet) Valve Cone (Inlet)

*Note: All individual parts may be ordered separately if required. DULTMEIER SALES • OMAHA, NE

Oil Seal

#09641 OIL SEAL KIT for P400 Series Pump

(3) (3) (3)

#09202 OIL SEAL KIT for P54W / P58W / P59W & P59MT-0020 Series Pumps

07391 08598 07392

Grooved Seal Ring Grooved Seal Pressure Ring, 12mm

(3)

#09119 PLUNGER PACKING KIT for P316 / P317 & P319 Series Pumps (3) (3) (6)

08477 08087 07904

08358 08346

Oil Seal

09202

Radial Shaft Seal

#09167 SEAL KIT for Model #P54W Series Pump

#09145 PLUNGER PACKING KIT for P318A & P320 Series Pumps (6) (3)

05444

SEAL KITS

Grooved Seal, Black Grooved Seal, Brown Pressure Ring, 18mm

(6) 07767 (3) 07768 (6) 07489 (3) 01009

Grooved Seal, 20mm Pressure Ring, 20mm

Automatic Seal Ring Support Ring O-Ring O-Ring

#09140 PLUNGER PACKING KIT for P420 & P425 Series Pumps

#09238 SEAL KIT for Model #P58W Series Pump

(3) 07266 (3) 12254 (3) 12255 (6) 08376

(6) 08477 (3) 07929 (3) 07489 (3) 12126 (3) 01009

O-Ring V-Sleeve Weep Seal Pressure Ring

Grooved Seal Support Ring O-Ring O-Ring O-Ring

#09038 PLUNGER PACKING KIT for P46W Series Pump (3) 07241 V-Sleeve (3) 07234 O-Ring

Part No. GU 09116 GU 09143 GU 09039 GU 09041 GU 09168 GU 09136

#09088 PLUNGER PACKING KIT for P55W Series Pump (3) 07011 V-Sleeve

#09037 PLUNGER PACKING KIT for P56W Series Pump

07011 06241 06242

Part No. GU 09164 GU 09152 GU 09119 GU 09145 GU 09140 GU 09138 GU 09088 GU 09037 GU 09089 GU 09061 GU 09477 GU 09138

V-Sleeve, Front V-Sleeve, Rear Support Ring

06076 08358 06240

V-Sleeve, Front V-Sleeve, Rear Support Ring

#09477 PLUNGER PACKING KIT for LP122A / LP123 & LP122A-4000 Series Pumps (For Pumps Manufactured after 4/98)

#09138 PLUNGER PACKING KIT for HR Series Pump

www.dultmeier.com

Fits Pump Model Net Ea. P217/P218/P219/P220/ P221/P227/P230 $ 52.40 P313/P314/321 54.25 P316/P317/P319 53.40 P318A & P320 44.60 P420 & P425 108.00 P46W 29.25 P55W 48.35 P56W 44.75 P55W with Weep Seals 100.00 P56W with Weep Seals 105.50 LP122A/LP123/LP122A-4000 240.50 HR Series 29.25

OIL SEAL KITS

SEAL KITS

Part No. Fits Pump Model GU 09167 P54W GU 09238 P58W

(3) 08087 V-Sleeve (3) 07904 Pressure Ring

284.00

Part No. Fits Pump Model Net Ea. GU 09144 P300 Series $ 3.25 GU 09641 P400 Series 21.85 GU 09202 P54W/P58W/P59W/ P59MT-0020 44.75

(3) 07740 O-Ring (3) 13415 V-Sleeve, Weep (6) 07745 V-Sleeve

(800) 228-9666

Net Ea. $ 49.70 241.50 66.40 58.55 121.00

PLUNGER PACKING KITS

#09061 PLUNGER PACKING KIT with Weep Seals for P56W Series Pump (3) (3) (3)

VALVE KITS Fits Pump Model P200/P300 P420/P422/P423/P425 P46W/P46W-HK P55W/P56W/P56W-HK P54W/P58W LP122A/LP123/ LP122A-4000/LP255

GU 09125 HR Series 8.11

(3) 06076 V-Sleeve

(3) (3) (3)

#09125 VALVE ASSEMBLY KIT for HR Series Pumps

08356-0010

(3)

(3) 07492 (3) 07906 (3) 07491 (3) 08404 (3) 07770

(3) 07751 Valve Assembly Complete (3) 12055 O-Ring

(3)

#09152 PLUNGER PACKING KIT for P313 / P314 & P321 Series Pumps

#09089 PLUNGER PACKING KIT with Weep Seals for P55W Series Pump

#09136 VALVE ASSEMBLY KIT for LP122A / LP123 / LP122A-4000 & LP255 Series Pumps

#09144 OIL SEAL KIT for P300 Series Pumps

V-Sleeve, Weep V-Sleeve, Brown Pressure Ring

#09168 VALVE ASSEMBLY KIT for P54W & P58W Series Pumps Tension Cap Valve Spring Valve Plate Valve Seat O-Ring

OIL SEAL KITS

• DAVENPORT, IA

(800) 553-6975

Net Ea. $ 135.50 52.30

E0044


REPAIR KITS

70

PACKING KITS

Packing REPAIR KITS

D

D

PACKING KITS

#09045 PLUNGER PACKING KIT for Model #LP121W Pump

#09089 PLUNGER PACKING WEEP KIT for Model P55W Pump

(6) 07140 (6) 07144 (3) 07137 (6) 02009

(3) (3) (3)

07011 07037 07240

#09037 PLUNGER PACKING KIT for Model P56W Pump

(3) 07740 O-Ring (3) 13415 V-Sleeve, Weep (3) 07745 V-Sleeve

(3) 06076 V-Sleeve

(6) 07272

V-Sleeve

#09038 PLUNGER PACKING KIT for P45 / P45W / P46W Pumps (3) 07241 V-Sleeves (3) 07234 O-Ring

#09081 PLUNGER PACKING WEEP KIT for P45 / P45W / P46W Pumps (3) 07241 (3) 07239 (3) 07240 (3) 07234

V-Sleeves Rear V-Sleeves Support Ring, Rear V-Sleeve O-Ring

#09088 PLUNGER PACKING KIT for P55 & P55W Series Pump (3) 07011 V-Sleeves

#09138 PLUNGER PACKING KIT for R5100 Series Pump (3) 08087 V-Sleeve (3) 10011 O-Ring

#09162 PLUNGER PACKING KIT for R5300 Series Pump (3) (6) (6) (3)

#09061 PLUNGER PACKING WEEP KIT for Model P56W Pump (3) (3) (3)

V-Sleeve with Support Ring, 20mm Pressure Ring, 20mm

V-Sleeve, Front Rear V-Sleeve Support Ring

#09477 PLUNGER PACKING KIT for LP123 Series

#09042 PLUNGER PACKING KIT for Model #MP4130W Pump

#09145 PLUNGER PACKING KIT for P318A & P320 Series Pump (6) 08358 (6) 08346

PACKING KITS

Retainer, O-Ring V-Packing Gasket Fitting O-Ring

D

06076 07039 07040

07902 07903 07904 08252

V-Sleeve, Black Support Ring Pressure Ring V-Sleeve, Brown

#09114 PLUNGER PACKING KIT, 14mm for Model #R56000 Series

V-Sleeve, Front Rear V-Sleeve Support Ring

(10) 07834 (10) 08266 (10) 07840

#09164 PLUNGER PACKING KIT for P200 Series Pump

V-Sleeve (14mm) O-Ring (14mm) Pressure Ring, (14mm)

#09077 PLUNGER PACKING KIT for Models #SP100, SP100W Pump

(6) 08477 V-Sleeve (3) 07904 Pressure Ring

(3) 07336 V-Sleeve

#09152 PLUNGER PACKING KIT for P313 Series Pump

PACKING KITS

#09119 PLUNGER PACKING KIT for P316, P317 & P319 Series Pumps

Part No. Fits Pump Model Net Ea. GU 09045 LP121W $ 243.00 GU 09042 MP4130W 194.00 GU 09038 P45/P45W/P46W 45.10 GU 09081 Weep Kit for P45/P45W/P46W 100.50 GU 09088 P55/P55W 48.35 GU 09089 Weep Kit for P55W 100.00 GU 09037 P56W 44.75

(6) 08477 (6) 07904

GU 09061 Weep Kit for P56W 105.50 GU 09164 P200 52.40 GU 09152 P313 54.25

(6) 08354 (6) 07392

V-Sleeve with Support Ring, 12mm Pressure Ring, 12mm

V-Sleeve with Support Ring, 18mm Pressure Ring, 18mm

GU 09119 P316/P317 GU 09145 P318A GU 09162 R5300 GU 09114 R56000

*Note: All individual parts may be ordered separately if required.

DULTMEIER SALES • OMAHA, NE

53.40 44.60 57.05 160.50

GU 09077 SP100/SP100W 59.50 GU 09138 R5100 29.25

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0045


Automatic Car Wash Parts

71

Replacement Parts for Many of the Most Popular Automatics

Photo-Electric Eye Sensors

Stainless Steel Chemical Injectors

Thru Beam - Up to 35 m

Stainless Steel Chemical Injectors for use as replacements in many common Automatics such as PDQ Systems. Injectors are stainless steel construction.

D

LT110TB Transmitter

D

See Page 106

Dual Barb No. 100541

D

D

LR110TB Receiver

Single Barb No. 100333

D

Hydraulic Adapter Unions

Amplifier

Plated or Stainless

See Page 274

D

D

See Page 258

Pressure Relief Valves

Male Union

Female Union

Air Pressure Regulators

D

See Pages 101 - 103

D

Air Regulators for control of air pressure to equipment.

See Page 307 - 308

D

Swivels Straight & 90°

Thermal Overload Relays D

See Pages 114 - 117 D

• Auxiliary Contacts: 1 NO + 1NC • Manual/Automatic RESET • Switching Position Indication • TEST Function

D

Check Valves

— High Pressure • High Temperature —

• STOP Button • Phase Failure Sinsitivity • Integrated, sealable Cover • CLASS 10

D

See Page 339

1/4”, 1/2”, 3/4” D

Cracking pressure is 8 PSI. Maximum temperature is 195° F. Viton® Seals. Standard on many automatic wash systems.

D

- Glycerin Filled -

Pressure Gauges

D

See Page 191

See Page 110

Replacement Nozzle Packs

Solenoid Valves

These kits give you all the necessary stainless steel replacement nozzles for PDQ Laser 4000, D&S 5000 or FUTURA & OASIS Touchless Automatics.

D

454P

See Page 168 - 173

D

See Page 133 DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0733


Motor Driven Drum Pumps

72

STANDARD PUMP Drum Pumps are a seal-less centrifugal design that are designed for the transfer of difficult chemicals and liquids from drums, totes and tanks. This wide range of pumps are ideal for Agriculture, Automotive, Plating, Chemical Packaging, Waste Water Treatments, Pharmaceuticals, Petroleum and many more. Sold in pump packs that include motor, 39” pump tube (47”, 60” & 72” also available), transfer hose, bung adapter, transfer nozzle and storage bracket. Motors are 1-Phase, 50/60 hz, 110 or 220 volt.

Pump Package #1

Pump Package #6

for Corrosive Water Treatment Chemicals

for Mineral Acids

Pump Pack #1 for Corrosive WaterTreatment Chemicals. Pump tube is CPVS, wetted parts are CPVC, Carbon and Hastelloy. Common chemical transfer includes Sodium Hypochlorite, Potassium Hydroxide, Calcium Chloride, Calcium Hydroxide, Chlorinated Water, Sodium Bromide and other products compatible with wetted parts. Viscosities to 1500cps. Rated to 15 GPM based on water. Rated to 190° F. Pump Part No. Volts Tube Wt.

SD 9430 SD 9431

110 220

Pump Pack #6 for Mineral Acids. Pump tube is 316SS, wetted parts are 316 stainless, Carbon and Teflon. Common chemical transfer includes nitric acid under 60%, citric acid, light oils and other products compatible with wetted parts. Viscosities to 1500cps. Rated to 21 GPM based on water. Rated to 175° F.

Part No. Volts Pump Tube Wt.

Net Ea.

CPVC 22 lbs. $ 815.00 CPVC 22 lbs. 829.00

SD 9414 110 SD 9415 220

316SS 316SS

Net Ea.

30 lbs. $ 1759.00 30 lbs. 1774.00

Pump Package #2

Pump Package #7

for Corrosive Acids & Alkalies

for Light Oils & Machining Lubricants Pump Pack #7 for Light Oils and Machining Lubricants. Pump tube is Aluminum, wetted parts are aluminum, carbon Teflon and 316SS. Common non-corrosive chemical transfer includes light machining oils, hydraulic fluid, motor oils to 30wt, Antifreeze products, lubricating oils and other products compatible with wetted parts.Viscosities to 1500cps. Rated to 22 GPM based on water. Rated to 175° F.

Pump Pack #2 for Corrosive Acids and Alkalies. Pump tube is Polypropylene, wetted parts are Polypropylene, Carbon and Hastelloy. Common chemical transfer includes Hydrochloric Acid to 20%, Nitric Acid to 20%, Acetic Acid, Alkalies, Sulfuric Acid and other products compatible with wetted parts. Viscosities to 1500cps. Rated to 15 GPM based on water. Rated to 130° F. Part No. Volts Pump Tube Wt.

Part No. Volts Pump Tube Wt.

Net Ea.

SD 9400 110 Polypropylene 21 lbs. $ 797.00 SD 9401 220 Polypropylene 21 lbs. 803.00

SD 9460 110 SD 9461 220

Pump Package #3

for Flammable & Combustible Liquids

Pump Pack #3 for Highly Concentrated Acids and Alkalies. For very concentrated and extremely aggressive liquids. Pump tube is PVDF, wetted parts are Kynar, Carbon and Hastelloy. Common chemical transfer includes Sulfuric Acid-66 Baume, Nitric Acid to 98%, Propionic Acid, Sodium Hypochlorite, Stearic Acid, Hydrofluoric Acid and other products compatible with wetted parts. Viscosities to 1500cps. Rated to 17.5 GPM based on water. Rated to 175° F.

SD 9420 SD 9421

Pump Pack #9 for Flammable and Combustible Liquids. Pump tube is 316SS, wetted parts are Stainless, Carbon and Teflon. Motors are explosion-proof design. Common chemical transfer includes gasoline, solvents, Toulene, petroleum products, alcohol, Aqueous Ammonia and other products compatible with wetted parts. Viscosities to 750cps. Rated to 18 GPM based on water. Rated to 175° F.

Pump Part No. Volts Tube Wt.

Net Ea.

SD 9610 SD 9611

110 PVDF-Kynar 28 lbs. $ 1195.00 220 CPVC 28 lbs. 1199.00

DULTMEIER SALES • OMAHA, NE

Net Ea.

22 lbs. $ 899.00 22 lbs. 925.00

Pump Package #9

for Highly Concentrated Acids & Alkalies

Pump Part No. Volts Tube Wt.

Aluminum Aluminum

(800) 228-9666

110 220

www.dultmeier.com

316SS 316SS

Net Ea.

39 lbs. $ 2619.00 39 lbs. 2619.00

• DAVENPORT, IA

(800) 553-6975

E1003


Transfer • Drum • Hand Pumps

73

Ezi-Action™ Drum Pumps

Plastic Hand Pumps Plastic Hand Pumps for a variety of chemical transfer applications. An ideal choice for transferring detergents, waxes, acids, solvents and ag chemicals. Designed for 5 gallon pails or 15/30/55 gallon drums as noted. (Note: Always check pump and chemical compatibility before use).

Ezi-Action™ Drum Pumps feature a unique design that allows for the transfer of a wide variety of chemicals and solutions. Even viscous products can be pumped. Suitable for pumping acid and alkalines, chlorines, oils, diesel, fertilizers and crop chemicals. Note: Not recommended for highly flammable liquids, strong solvents or gasoline products. Available for 5 gallon pails and 30 gallon or 55 gallon drums.

– Pail Pumps – Model PSP1 is an inexpensive polyethylene siphon pump. Squeeze pump creates siphon action to drain product from 5 gallon pails. Includes adapters for 3/4” drum fittings, 2” bung fittings, flex spouts and rigid containers. Discharge hose is 22”.

PSP1 D

Locking Handle

D

STANDARD FEATURES: • Polypropylene and polyethylene construction

Model MR50-5 is a compact hand pump that features a polyethylene body and Viton® o-ring. Can be used for detergents and mild chemicals from 5 gallon pails. Includes rigid discharge spout, Inlet tubes and adapters will fit 3/4” drum fittings, 2” bung fittings, flex spouts and rigid containers. Adjustable output from 2,4,6 or 8 ozs. per stroke.

• Anti-pumping safety lock on handles • Swivel Discharge spout for drip-free operation

50S Safety Measure

• 2-Year Warranty • Free service kits for the life of the pump

PAIL PUMPS Part-No.

Ezi-Action™ Safety Measure. Great accessory for closed delivery and accurate measurement of pumped solutions. Mounts to all Ezi-Action pump spouts for hands-free dispensing. Capacity is 32 oz. (1 Liter). Measurements shown in ounces and milliliters. Construction is polyethylene. Part No.

NZ 255 NZ 6015 NZ 20055 NZ 50S NZ 70SK

Container Output/ Size Stroke

Wt.

TO PSP1 TO MR50-5

Hand Transfer Pump

365 D D

HPV4A Polyester Glass Reinforced pump with Viton® internals, & cross linked polyethylene hose

Net Ea.

5 Gallon 5 Gallon

$ 7.77 24.00

Model DSP2 is an inexpensive hand pump designed for 55 gallon drums with heavy buttress bung fittings. All polyethylene construction. Discharge tube is 40”. Up/down design develops 4 oz. per stroke. Models 360 & 365 Drum pumps feature up/down handle design with rigid discharge spout and stainless plunger rod. Both models fit 15, 30 or 55 gallon drums. Rated to 8 ozs. per stroke. Tube length is 37”.

DSP2

HE4 Polyester Glass Reinforced pump with Viton® internals and EPDM hose.

Fits Containers

– Drum Pumps –

Net Ea.

Drum Pump 5 Gallon 6 oz. 1.0 lbs. $ 33.50 Drum Pump 30 Gallon 15 oz. 1.5 lbs. 40.05 Drum Pump 55 Gallon 15 oz. 1.6 lbs. 47.35 Safety Measure, 32 oz........................................ 7.97 Service Kit........................................................... No Charge

For many chemicals, acetone, methanol and ethanol solvents. Supplied with a 2" bung adaptor, 8' long hose, hose end nozzle with built-in syphon breaker and two-piece suction tube for 55 gallon drums. The Body and components are glass-filled polyester or Ryton®, Piston rod and springs are stainless. Double acting handle pumps one-half quart on each forward or backward stroke. Capacity: 25 gallons per 200 strokes. Max Liquid Temperature: 125° F. Max Liquid Viscosity: 2000 SSU. Port Diameters: Inlet 1" NPT, Outlet 3/4" MPT. Weight: 8 lbs.

Pail Pump Pail Pump

MR50-5

D

Fits Containers

TO DSP2 Drum Pump NS 360 Drum Pump NS 365 Drum Pump

HRV4A Ryton ® Glass Reinforced Pump with Viton® internals, cross linked polyethylene hose and polyester suction tube. For maximum chemical resistance.

360

Model 360 features polypropylene body and “Viton® E” o-ring. Good choice for detergents, anti-freeze and mild chemicals. Model 365 features nylon body and Teflon o-ring. Best choice for aggressive chemicals, solvents, mild acids, acetones and windshield fluids.

DRUM PUMPS Part-No.

RESISTS ATTACK from many chemicals and acids.

D

Net Ea.

55 Gallon $ 15.50 15, 30/55 Gallon 26.66 15, 30/55 Gallon 43.47

Not recommended for use with: Chlorinated hydrocarbons, elastomers, and some fumigants such as Dibrom and Telone II.

Visit Our Web Site at

Products that use a petroleum based material such as diesel fuel will require pumps with Viton® internals.

http://www.dultmeier.com or E-Mail us at

Part No. PR HE4 PR HPV4A PR HRV4A PR 3456 PR 167P

PACER PISTON PUMPS Net Ea. Glass-filled Polyester Pump............................ $ 109.00 Glass-filled Polyester Pump............................ 145.50 RYTON® Transfer Pump ................................ 229.00 Polyethylene Suction Tube (as replacement).. 15.05 Repair Kit for HE4/HPN.................................. 38.40 DULTMEIER SALES • OMAHA, NE

(800) 228-9666

dultmeier@dultmeier.com Viton® is a registered trademark of DuPont Performance Elastomers

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0064


Barrel & Drum Hand Pumps

74

Drum and Barrel Pumps for a wide variety of transfer applications. Designed for Acids, Alkalis, Solvents, Detergents, Chlorine, Petroleum Products, Dairy Chemicals and Water Removal. Most pumps are sold with 2” IPS adapters for the most common drums and barrels. However, ACT or Rieke Buttress, Glass Carboy and Poly Carboy adapters are also available. Pumps are offered with discharge hose or spouts as shown. (Note: Pump and chemical compatibility should always be checked before use.)

Acid/Alkali/Detergent Hand Pumps

Dairy Chemical Hand Pumps

Hand operated pumps for safely transferring detergents, waxes, alkalis and acids. Pumps are 38” long, 1-1/2” in diameter and deliver 28 oz. per stroke. 2” IPS fine thread bung adapter is included. Model 236 features PVC barrel and shaft with Viton® seals and valves. 36” polyethylene discharge hose is included. UL listed for transfer of up to 50% Sulfuric Acid at up to 120° F. Model 436 features PVC barrel and shaft with “Hypalon” seals and valves. 36” polyethylene discharge hose is included. Best choice for Alkalis. UL listed for transfer of up to 30% Hydrochloric Acid at up to 100° F. ACID/ALKALI/DETERGENT PUMPS Part-No. Seal

BI 236PF3S BI 436PF3S

Hand Pump Hand Pump

These pumps are designed to transfer most dairy soaps and alkalis used in cleaning milk lines. Pumps feature PVC barrels with “Hypalon” valves and seals. Standard safety features include twist handle to prevent inadvertent lifting of handle, patented “strap lock” to prevent unauthorized use and antisiphon spout to reduce spills. 1-1/4” diameter in either 12” or 18” lengths. 18” Dip tubes are included to reach the bottom of chemical containers. 2” IPS bung adapter is also included.

D

DAIRY CHEMICAL PUMPS Part-No. Length

236 436

BI DP12SPS BI DP18SPS

Output/Stroke

Net Ea.

28 oz. 28 oz.

$ 68.60 63.50

Viton® Hypalon

12” 18”

Model 536PSP is designed for transferring most solvents, alcohols and alkalis. Construction is high density polyethylene (HDPE). Sealess design. 2” buttress bung adapter is optional, but not required for use. Barrel is 35” long. 14’ Swivel discharge spout is included to eliminate drips.

Output/Stroke

Net Ea.

20 oz.

$ 93.25

Model 336 offers an effective and easy way to transfer oils, kerosene, diesel fuel, etc. Features PVC barrel with urethane valves and Buna seals. Pumps are 38” long x 1-1/2” diameter. Rated to 28 oz. per stroke. 36” Discharge hose and 2” IPS bung adapter is included.

Output/Stroke

Net Ea.

5 oz. 8 oz.

$ 32.95 35.80

9”

Seal

Output/Stroke

Net Ea.

Viton®

5 oz.

$ 26.00

Water Hand Pumps Model 12A is an ideal choice for draining traps or pipes. Diameter is 1-1/2” x 12” long. 3’ inlet tube fits onto bottom of pump and extends down into trap or drain. Includes outlet tube for directing flow into pail or bucket. Sealess design. Output is 8 oz. per stroke.

Petroleum Hand Pump

Models 230PF & 136PF6 Pumps are designed for manual removal of water when electrical means are not available. Just place pump end in water and up/down motion removes water easily and quickly. Construction is high impact PVC. No priming is required. Discharge hose is included with both models.

D

Models 915F Compact hand water pump. Includes 2” x 36” flexible intake tube with foot valve and 7’ outlet tube for directing discharge flow. Pump is 3” diameter x 24” long. Output is as high as 16 GPM. Construction is PVC.

336PF3S

PETROLEUM PUMP Part-No.

Seal

Output/Stroke

Net Ea.

BI 336PF3S

Buna

28 oz.

$ 59.75

Hand Pump

CHLORINE PUMP Part-No. Length

BI SP1209M

BI 536PSP Hand Pump

Seal

Hypalon Hypalon

A hand pump that is specifically designed for transferring Liquid Chlorine from 5 gallon containers with 70mm lid caps. Standard with a twist handle to prevent inadvertent lifting of handle and safety strap to help prevent unauthorized use. Pump is 1-1/4” diameter x 9” length Output is 5 oz. per stroke. 9” discharge hose is included. Construction is PVC with Viton® seals.

Solvent Hand Pump

SOLVENT PUMP Part-No.

DP12SPS DP18SPS

Chlorine Hand Pump SP1209M D

536PSP

D

D

BioFuels Hand Pump D

12A D

636PF3S

Model 636 is designed for the transfer of BioFuel products from drums or pails to equipment fuel tanks. Non-sparking construction. Features a PVC barrel and Viton® valves and seals. Pump has 36” barrel x 1-1/2” diameter. Rated to 28 oz. per stroke. 36” Hose and 2” IPS bung adapter are included.

BIOFUELS PUMP Part-No.

BI 636PF3S

Hand Pump

Seal

Output/Stroke

Net Ea.

Viton®

28 oz.

$ 63.95

D

915F 230PF/136PF6 WATER PUMPS Part-No.

BI 12A BI 230PF BI 136PF6 BI 915F

Length

Discharge

Output/Stroke

Net Ea.

12” 30” 36” 24”

12” Pipe 30” Hose 72” Hose 84” Hose

8 oz. 22 oz. 35 oz. 34 oz.

$ 21.75 35.50 46.95 174.50

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0948


Air Driven Diaphragm Pumps

75

Yamada® Air Operated Diaphragm Pumps

Air-Operated Diaphragm Pumps GRACO Air-Operated Diaphragm Pumps. Designed for a wide variety of chemicals, solutions, coatings, solvents or abrasives. Ideal for tough, viscous products. Air supply range is 25 - 100 PSI (125 PSI for 1” and larger). Features: Polypropylene, Aluminum or Kynar Bodies with Buna, Hytrel, Santoprene or Teflon diaphragms • Seal-less, leak-proof design prevents fluid waste or spills • Pumps can run dry without damage • Air drive means no electrical hazards • Lightweight and portable for multi-location use • Poly, Kynar and Aluminum pumps with Santoprene diaphragms are rated to 180° F. and pumps with Teflon diaphragms are rated to 220° F. • Limited number of parts means fast repairs.

Air-Powered, Double-Diaphragm Pumps. Ideal for pumping tire chemicals in CTA units, wheel brite chemicals or bug cleaner products. Unique, simple, safe. These pumps will handle practically anything that will flow. Multi-purpose pumps are available for almost every plant in every industry. Abrasive and corrosive fluids can be handled without problems.

D

Husky 205 Series 1/4” Ports 1.5mm Solids (5 GPM)

Model NDP-15FPT Pumps shown have Polypropylene, Aluminum or Kynar bodies (poly is standard unless noted) and either Teflon, Neoprene, Hytrel or Buna diaphragms and valves. Pumps are rated: 180° F. for Poly, 212° F. for Kynar and 180° F. for Aluminum. Pumps have an air supply range from 20 to 100 PSI. For higher temperatures or other compatibility requirements, Stainless Steel bodies and sizes up to 3" are also available.

D

Husky 515 Series 1/2” Ports 2.5mm Solids (15 GPM)

STANDARD FEATURES: Air Driven-Intrinsically Safe. Air drive allows you to be free from electrical hazards or explosion-proof motor requirements. Excellent Wear Resistance & Minimum Maintenance. Without moving parts in contact with the liquids or rotating parts to wear, the pump is almost maintenance free.

D

Self-Priming, Dry Start. Completely self-priming. Also, if liquid source runs dry, the pump can continue to operate without damage from overheating or friction wear unit further liquid is available. Flow Control. Infinitely variable flow control can be regulated by simply opening or closing a valve on the discharge, or by increasing or decreasing the air supply.

Husky 1050 Series 1” Ports 3.2mm Solids (50 GPM)

High Lift and Distance Transfer. Because pumps are designed at a 1:1 ratio, discharge pressures are equal to the air inlet pressure. Maximum pressure is approximately 70 PSI on the Poly pumps.

D

Versatile Material Handling. Product capabilities range from clear water to highly viscous, abrasive or aggressive materials.

Pulsation Dampeners Available

Husky 1590 Series 1-1/2” Ports 4.8mm Solids (100 GPM)

D

D

Model NDP-5FVT

Max. Pump Max. Part No. Ports Pump Body Diaphragm Flow Net Ea. Part No. Ports Body Diaphragm Flow GY D12096 1/4" FPT Polypropylene Santoprene 5 GPM $ 196.00 YA NDP-5FPT 1/4" FPT Polypropylene Teflon 3-1/2 GPM GY D12091 1/4" FPT Polypropylene Teflon 5 GPM 291.50 YA NDP-5FVT 1/4" FPT Kynar Teflon 3-1/2 GPM GY D150A1 1/4" FPT Kynar Teflon 5 GPM 374.00 YA DP-10BPH 3/8" FPT Polypropylene Hytrel 5 GPM GY D32966 3/8” FPT Polypropylene Santoprene 7 GPM 291.50 YA DP-10BPSE 3/8" FPT Polypropylene Santoprene 5 GPM GY D32955 3/8” FPT Polypropylene Hytrel 7 GPM 301.50 YA DP-10BPT 3/8" FPT Polypropylene Teflon 5 GPM GY D32911 3/8” FPT Polypropylene Teflon 7 GPM 374.00 YA NDP-15FPH 1/2" FPT Polypropylene Hytrel 13 GPM GY D52966 1/2” FPT Polypropylene Santoprene 15 GPM 374.00 YA NDP-15FPS 1/2" FPT Polypropylene Santoprene 13 GPM GY D52955 1/2” FPT Polypropylene Hytrel 15 GPM 402.00 YA NDP-15FPT 1/2" FPT Polypropylene Teflon 13 GPM GY D52911 1/2” FPT Polypropylene Teflon 15 GPM 517.00 YA NDP-15FVT 1/2" FPT Kynar Teflon 13 GPM GY D45A11 1/2” FPT Kynar Teflon 15 GPM 809.00 YA NDP-20BPC 3/4" FPT Polypropylene Neoprene 28 GPM GY D53277 3/4” FPT Aluminum Buna 16 GPM 474.50 YA NDP-20BPH 3/4" FPT Polypropylene Hytrel 28 GPM GY D53366 3/4” FPT Aluminum Santoprene 16 GPM 454.50 YA NDP-20BPT 3/4" FPT Polypropylene Teflon 28 GPM GY D53211 3/4” FPT Aluminum Teflon/EPDM 16 GPM 534.00 YA NDP-20BAN 3/4" FPT Aluminum Buna 28 GPM GY 647074 1” FPT Aluminum Buna 50 GPM 714.00 YA NDP-25BAH 1" FPT Aluminum Hytrel 45 GPM GY 647035 1” FPT Aluminum Santoprene 50 GPM 647.00 YA NDP-25BPC 1" FPT Polypropylene Neoprene 45 GPM GY 647075 1” FPT Aluminum Teflon/EPDM 50 GPM 780.00 YA NDP-25BPH 1" FPT Polypropylene Hytrel 45 GPM GY 649029 1” ANSI Flange Polypropylene Santoprene 50 GPM 817.00 YA NDP-25BPT 1" FPT Polypropylene Teflon 45 GPM GY 649034 1” ANSI Flange Polypropylene Teflon 50 GPM 928.00 YA NDP-25BAN 1” FPT Aluminum Buna 45 GPM GY 649038 1” ANSI Flange Kynar Teflon 50 GPM 1018.00 YA NDP-40BAN 1-1/2" FPT Aluminum Buna 100 GPM GY DB2911 1-1/2” Flange Polypropylene Teflon 100 GPM 2079.00 YA NDP-40BAS 1-1/2" FPT Aluminum Santoprene 100 GPM GY DB2966 1-1/2” Flange Polypropylene Santoprene 100 GPM 1894.00 YA NDP-40BPN 1-1/2" Flange Polypropylene Buna 100 GPM GY DB5A11 1-1/2” Flange Kynar Teflon 100 GPM 3908.00 YA NDP-40BPT 1-1/2" Flange Polypropylene Teflon 100 GPM GY DB3777 1-1/2” FPT Aluminum Buna 100 GPM 783.00 YA NDP-50BAN 2" FPT Aluminum Buna 150 GPM GY DF2911 2” Flange Polypropylene Teflon 150 GPM 2986.00 YA NDP-50BAT 2" FPT Aluminum Teflon 150 GPM GY DF2966 2” Flange Polypropylene Santoprene 150 GPM 2770.00 YA NDP-50BPT 2" Flange Polypropylene Teflon 150 GPM GY DF5A11 2” Flange Kynar Teflon 150 GPM 6041.00 GY DF3777 GY 652036

2” Flange 3” Flange

Aluminum Aluminum

Buna 150 GPM Santoprene 275 GPM

DULTMEIER SALES • OMAHA, NE

1006.00 1995.00

(800) 228-9666

Net Ea. $ 183.00 567.00 253.50 253.50 285.00 296.50 302.00 316.00 729.00 612.00 612.00 679.00 520.00 618.00 761.00 761.00 833.00 617.00 833.00 803.00 1574.00 1905.00 1004.00 1594.00 2708.00

Note: Above Pumps should always have a filter/regulator on the air supply line.

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0049


Air Driven Diaphragm Pumps

76

SandPiper Air-Driven Diaphragm Pumps from Warren Rupp. “No-Stall” design for continuous operation. Ideal for abrasives, caustics, corrosives and viscous chemical transfer. Pumps can run dry without damage. Air drive means no motors or engines are required. ISO Certified. Inlet supply pressure is 20 to 100 PSI on plastic pumps and 20 to 125 PSI on metal pumps. Maximum discharge pressure is 100 PSI. Maximum viscosity is 10,000 SSU or 2200 CPS. Maximum temperatures to 150° F. Pumps are available in a variety of sizes and construction to meet your needs. Other pump configurations and sizes are available in addition to those shown.

Air-Driven Diaphragm Pumps

PLASTIC BODIES

D

Part No. Ports SO TS3PP 1/4” SO TT3PP 1/4” SO TT3K 1/4” SO 5PPB 1/2” SO 5PPS 1/2” SO 5PPT 1/2” SO 5PPK 1/2” SO 7B1P1 3/4” SO 7B1P2 3/4” SO 1FB2P3 1” SO 1FB2P1 1” SO 1FB2P2 1” SO 1FB2PK 1” SO S15B33 1-1/2” SO S15B31 1-1/2” SO S15B32 1-1/2” SO S20B3 2” SO S20B1 2” SO S20B2 2”

Body Polypropylene Polypropylene Kynar Polypropylene Polypropylene Polypropylene Kynar Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Kynar Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene

Diaphragm Santoprene Teflon Teflon Buna Santoprene Teflon Teflon Santoprene Teflon Buna Santoprene Teflon Teflon Buna Santoprene Teflon Buna Santoprene Teflon

Max. Flow 4 GPM 4 GPM 4 GPM 14 GPM 14 GPM 14 GPM 14 GPM 23 GPM 23 GPM 45 GPM 45 GPM 45 GPM 45 GPM 100 GPM 100 GPM 100 GPM 150 GPM 150 GPM 150 GPM

Wt. Net Ea. 4 lbs. $ 208.00 4 lbs. 252.50 4 lbs. 323.00 16 lbs. 413.00 16 lbs. 449.50 16 lbs. 529.00 16 lbs. 851.00 17 lbs. 559.00 17 lbs. 723.00 53 lbs. 1006.00 53 lbs. 999.00 53 lbs. 1226.00 53 lbs. 1934.00 105 lbs. 1989.00 105 lbs. 1989.00 105 lbs. 2449.00 117 lbs. 2898.00 117 lbs. 2898.00 117 lbs. 3298.00

Diaphragm Buna Santoprene Teflon Santoprene Teflon Buna Santoprene Teflon Santoprene Teflon Buna Santoprene Teflon Santoprene Teflon Buna Santoprene Teflon Santoprene Teflon

Max. Flow Wt. Net Ea. 15 GPM 15 lbs. $ 575.00 15 GPM 15 lbs. 575.00 15 GPM 15 lbs. 778.00 15 GPM 21 lbs. 1266.00 15 GPM 21 lbs. 1398.00 45 GPM 28 lbs. 713.00 45 GPM 28 lbs. 715.00 45 GPM 28 lbs. 931.00 45 GPM 43 lbs. 1489.00 45 GPM 43 lbs. 1664.00 106 GPM 53 lbs. 928.00 106 GPM 53 lbs. 928.00 106 GPM 53 lbs. 1359.00 106 GPM 95 lbs. 2675.00 106 GPM 95 lbs. 2849.00 150 GPM 77 lbs. 1354.00 150 GPM 77 lbs. 1354.00 150 GPM 77 lbs. 1767.00 150 GPM 120 lbs. 3750.00 150 GPM 120 lbs. 4598.00

D

Removable Air Valves

METAL BODIES

Polypropylene or Kynar Housings

Part No. SO S05BAB SO S05BAS SO S05BAT SO SS5BS1 SO SS5BS2 SO S1FBAB SO S1FBAS SO S1FBAT SO SBSS1W SO SBSS2T SO S15B1AB SO S15B1A1 SO S15B1A2 SO S15B1S1 SO S15B1S2 SO S20B1AB SO S20B1A1 SO S20B1A2 SO S20B1S1 SO S20B1S2

Ports 1/2” 1/2” 1/2” 1/2” 1/2” 1” 1” 1” 1” 1” 1-1/2” 1-1/2” 1-1/2” 1-1/2” 1-1/2” 2” 2” 2” 2” 2”

Body Aluminum Aluminum Aluminum Stainless Stainless Aluminum Aluminum Aluminum Stainless Stainless Aluminum Aluminum Aluminum Stainless Stainless Aluminum Aluminum Aluminum Stainless Stainless

D

Metal Housings

Versa-Matic Air Diaphragm Pumps PLASTIC PUMPS

Air-Driven Diaphragm Pumps from Versa-Matic. Exclusive Air Valve System. Anti-stalling, non-icing and lubrication-free. Designed to handle a wide range of products from water to 90% solids easily and efficiently. Available from 3/8” to 3” sizes. Bodies are polypropylene, aluminum, stainless or Kynar. A wide range of diaphragms and pump bodies will handle temperatures between 175° F. and 225° F. depending on construction. Pumps are rated from 100 to 120 PSI depending on model. D Ports are FPT or ANSI flange compatible as shown.

Part No. Ports VA E8PP6X 3/8” FPT VA E8PP5T 3/8” FPT VA E8KP5B 3/8” FPT VA E5PP2R 1/2” FPT VA E5PP6X 1/2” FPT VA E5PP5T 1/2” FPT VA E5KP5T 1/2” FPT VA E1PP2R 1” Flange VA E1PP6X 1” Flange VA E1PP5T 1” Flange VA E1KP5T 1” Flange VA E4PA2 1-1/2” Flange VA E4PA6 1-1/2” Flange VA E4PA5 1-1/2” Flange VA E2PA2 2” Flange VA E2PA5 2” Flange

Body Polypropylene Polypropylene Kynar Polypropylene Polypropylene Polypropylene Kynar Polypropylene Polypropylene Polypropylene Kynar Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene

Diaphragm Santoprene Teflon Teflon Buna Santoprene Teflon Teflon Buna Santoprene Teflon Teflon Buna Santoprene Teflon Buna Teflon

Max. Flow 6.8 GPM 5.5 GPM 5.5 GPM 14 GPM 14 GPM 11 GPM 11 GPM 35 GPM 35 GPM 28 GPM 28 GPM 72 GPM 72 GPM 57 GPM 140 GPM 112 GPM

Wt. Net Ea. 3 lbs. $ 103.00 3 lbs. 145.50 4.5 lbs. 279.00 10 lbs. 324.00 10 lbs. 323.50 10 lbs. 403.00 10 lbs. 699.00 24 lbs. 561.00 24 lbs. 571.00 24 lbs. 711.00 25 lbs. 1203.00 32 lbs. 1283.00 32 lbs. 1309.00 32 lbs. 1206.00 72 lbs. 1988.00 72 lbs. 2303.00

Body Aluminum Aluminum Aluminum Stainless Stainless Aluminum Aluminum Aluminum Stainless Stainless Aluminum Aluminum Aluminum Stainless Stainless Aluminum Aluminum Aluminum Stainless Stainless

Diaphragm Buna Santoprene Teflon Santoprene Teflon Buna Santoprene Teflon Santoprene Teflon Buna Santoprene Teflon Buna Teflon Buna Santoprene Teflon Santoprene Teflon

Max. Flow Wt. Net Ea. 14 GPM 15 lbs. $ 426.00 14 GPM 15 lbs. 443.00 11 GPM 15 lbs. 508.00 14 GPM 18 lbs. 873.00 11 GPM 18 lbs. 939.00 35 GPM 31 lbs. 462.00 35 GPM 31 lbs. 502.00 28 GPM 31 lbs. 612.00 35 GPM 42 lbs. 1001.00 28 GPM 42 lbs. 1115.00 70 GPM 41 lbs. 720.00 70 GPM 41 lbs. 732.00 56 GPM 41 lbs. 895.00 70 GPM 57 lbs. 1702.00 56 GPM 57 lbs. 2099.00 160 GPM 74 lbs. 877.00 160 GPM 74 lbs. 934.00 128 GPM 74 lbs. 1308.00 160 GPM 120 lbs. 2461.00 128 GPM 120 lbs. 2906.00

METAL PUMPS

E8PP6X Polypropylene

E4AA2 Aluminum Flanged

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

Part No. Ports VA E5AA2 1/2” FPT VA E5AA6 1/2” FPT VA E5AA5 1/2” FPT VA E5SP6 1/2” FPT VA E5SP5 1/2” FPT VA E1AA2 1” FPT VA E1AA6 1” FPT VA E1AA5 1” FPT VA E1SP6 1” FPT VA E1SP5 1” FPT VA E4AA2 1-1/2” Flange VA E4AA6 1-1/2” Flange VA E4AA5 1-1/2” Flange VA E4SA6 1-1/2” Flange VA E4SA5 1-1/2” Flange VA E2AA2R 2” Flange VA E2AA6X 2” Flange VA E2AA5T 2” Flange VA E2SA6D 2” Flange VA E2SA5T 2” Flange

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0048


Air Driven Transfer Pumps

77

FLOJET Air Driven Diaphragm Pumps

FLOJET Air Pumps

Ideal for use with Tire Cleaner or Bug Cleaner Products in Tunnel or Rollover installations. Air Drive design allows for easy hook-up. Self-priming style with automatic shut-off. Maximum flow is 2.5 GPM. Maximum inlet temperature is 120° F. Maximum pressure is 80 PSI. D Standard Features Include: Infinitely variable capacity from zero to maximum flow. • Automatic demand operates pump only when discharge valve or gun is open, stops instantly when valve is closed. • Pump can run dry without causing damage. • Liquid being pumped does not come in contact with any metal parts. • No electrical connections. • No pressure relief valve or bypass plumbing is required. • Santoprene Elastomers for added chemical resistance. • Acetal/Celcon body • Air Ports are 1/4” Barb.

Model G5700 Single & G257 Dual Diaphragm Air Driven Transfer Pumps. A compact pump with high flow and pressure capabilities. Applications include Chemical Transfer and Automotive Cleaning. Bag-inthe-Box Chemicals, Parts Washers. Capable of passing up to 1/8" solids. D

G5700

Flow rates to 10 GPM and pressures to 100 PSI. • Temperatures to 120° F. • Self-priming to 15' • Patented shuttle valve eliminates stalling • Constructed of corrosion resistant materials to handle a wide variety of chemicals. Construction: Body is Polypropylene • Diaphragms and check valves are Santoprene®, Viton® or Kalrez • Springs are 316SS. Specifications: Gas inlet and outlet are 1/4" • Product inlet and outlet are 1/2" barbs.

Part No. Diaphragm/Valves Air Ports Fluid Ports Net Ea. FJ 5100-040 Santoprene 1/4" Barb 3/8" Barb $ 66.40 FJ 5100-020 Viton® 1/4" Barb 3/8" Barb 84.50 FJ 5100-050 * Geolast 1/4" Barb 3/8" Barb 81.95 FJ 20467-003 Santoprene Valve Kit, pumps prior to 2008 ........... 17.00 FJ 20467-002 Viton® Valve Kit, pumps prior to 2008 ................... 19.80 GN 6ZC63 Air Filter - 1/4" M x 1/4" F (Pkg. of 2)..................... 23.95 * Geolast is best for petroleum base products. NOTE: Viton® & Santoprene Kits are no longer interchangeable on pumps.

G257

MODEL G257 Air Pump Flow Rate GPM (L/min) *Indicates Air Inlet Pressure

Air Diaphragm Pump • Ideal for Chemical Transfer & Pumping

D

• High Efficiency Pneumatic Spool Valves

D

• Handles High Viscosity Liquids • Can Run Dry Without Damage

Double-Diaphragm Air Pump from Shurflo. No stall, high efficiency pneumatic spool valves for long, trouble-free operation. Ideal for chemical transfer and pumping applications. Rated to 10 GPM open flow and pressure from 40 to 100 PSI. Temperatures to 120° F. Can run dry without damage. Can handle high viscosity liquids. 1/4” air barb with 1/2” & 3/4” liquid barbs are included for ease of plumbing. Part No.

Elastomers

SU 477-40001

Santoprene

Max. PSI

100

Wt.

2.5 lbs.

Part No.

Diaphragm

FJ G5700 FJ G5700V FJ G5700C FJ G257501A FJ G257301A FJ 20730-000A FJ 20740-050A FJ 21000-209 FJ 20740-020A

Santoprene** 7 GPM 100 $ 88.95 Viton® 7 GPM 100 128.00 † Kalrez 7 GPM 100 143.50 Santoprene** 10 GPM 100 219.00 Viton® 10 GPM 100 264.50 Diaphragm Kit, Santoprene**............ 18.10 Check Valve Kit, Santoprene**.......... 13.15 Diaphragm Kit, Viton®....................... 33.45 Check Valve Kit, Viton®..................... 44.20

* Maximum air consumption is 2.8 cfm @ 120 psi. † Higher chemical resistance than Viton® or Santoprene. ** Santoprene is a registered trademark of Monsanto Co.

Universal Mounting Bracket

Net Ea.

$ 96.80

• Single brackets snap together easily for multiple pump installations.

Air Operated Pumps Ideal for tire cleaners, bug cleaners, foam brush solutions, presoak chemicals, acid products and many more.

• For use with G5700 & 5100 Series and Shurflo® Air Driven Pumps.

D

• Ideal for mounting on rack or wall.

Two-chamber, dual diaphragm design. Powered by compressed air, CO2 gas or nitrogen. Temperature range is +34° to +120° F. Size is 7" x 6" x 4". Inlet and outlet fittings are 3/8" SS hose barbs. Air inlet fitting is 1/4" nylon hose barb.

Max Flow *Max PSI Net Ea.

Part No.

Net Ea.

FJ 20982-100A Single Pump Mounting Bracket

$ 4.95

D

Air Filter / Dryer

Suction lift (wet) is 25 in/hg. Pumping distance will vary with viscosity. Maximum flow is 2.20 GPM @ 20 PSI discharge & 60 PSI air inlet. Polypropylene body, 316SS internals and Viton® or EPDM diaphragms are standard for added chemical compatibility.

Two Stage Air Filter / Dryer is designed to remove moisture and debris from air supply lines. Protects air pumps, tools, etc. from dirt, dust, oil and moisture. Standard with manual drain valve and replaceable cartridge filters. Rated to 15 CFM. Pressures to 250 PSI and temperatures to 180° F. Ports are 1/4" FPT.

Part No. Diaphragms *Flow @ 30 PSI Fluid Ports Wt. Net Ea. SU 166-20036 VITON® 1.75 gpm 3/8" 2 lbs. $ 111.50 SU 166-20056 EPDM 1.75 gpm 3/8" 2 lbs. 85.95 SU 94-175-06 EPDM Diaphragm & Valve Kit.................................... 13.15 Part No. SU 94-175-05 VITON® Diaphragm & Valve Kit................................. 51.80 FJ FJ520B Filter / Dryer SU 94-175-07 Santoprene Diaphragm & Valve Kit ......................... 11.80 * Based on 60 psi inlet pressure. Viton® is a registered trademark of DuPont Performance Elastomers DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

Net Ea.

D

$ 116.50

(800) 553-6975

E0051


Air Operated Double Diaphragm Pumps

78

Air-Operated Double Diaphragm Pumps The Most Advanced Air-Operated Diaphragm Pump on the Market! A revolutionary new process pump that can handle the day after day use in a grueling industrial environment. The SP100 Series Air-Operated Double Diaphragm Pump can be configured in materials that are resistant to many industrial chemicals and proven to provide complete compatibility coverage for a wide range of fluids. With it’s extensive list of features, the SP100 Series outperforms the competition time and time again. SP100-5 Series 1/2” Non-Metallic

• 15% More Flow &

Reinforced Manifold

An encapsulated stainless steel ring embedded around the threads prevents over tightening & the potential splitting of the manifold

20% More Efficient

• 66% Less Pulsation &

Ball Check & Seats

67% Fewer Parts

The ball & seat sets are matched elastomer combinations that offer a minimum 20% improvement in suction lift due to tighter seals.

Ceramic Air Valve

• 50% Less Repair Time • 360° Uniform Seal

The patented QuikFlow® air valve provides fast trip over, resulting in a 60% reduction in pulsation.

Unique Diaphragm Construction

A stainless steel shaft with a reinforced diaphragm nut fully supports the diaphragm & prevents cross threading. The uniform seal hinge minimizes wear.

D

Foot Mount

Retrofits into most existing mounting plates.

Easy-Off Threaded Ring Construction

5 Year Warranty

The Quik-Seal® ring is designed for quick-turn access to clear ball checks & to replace diaphragms.

SP100-5 Series Maximum Solids: 3/32” Maximum Flow Rate: 17.5 GPM Maximum Air Inlet Pressure/ Discharge Pressure: 100 PSI

SP100-10X 1” Metallic

Patented Ring Construction - No Bolts Needed

D

Bolted Manifold for Quick & Easy Maintenance

Kits & Accessories Wall Mount Brackets

KITS05M

Muffler

Quick Flow Patented Air Valve Assembly

SP100-10 Series Maximum Solids: 3/16” Maximum Flow Rate: 56 GPM Maximum Air Inlet Pressure/ Discharge Pressure: 100 PSI

5 Year Warranty

DULTMEIER SALES • OMAHA, NE

Filter/Regulator Assemblies

KITS05

KITS10W

KIT180MPPS

Tote Plate

Double Diaphragm Pumps Part No. Ports Body Diaphragm Max. Flow Wt. Net Ea. FR SP100-5S 1/2” Polypropylene Santoprene 17.5 GPM 8 lbs. $ 340.00 FR SP100-5T 1/2” Polypropylene Teflon 17.5 GPM 8 lbs. 448.00 FR SP100-10H 1” Aluminum Hytrel 56.0 GPM 15 lbs. 605.00 Kits & Accessories FR KIT180MPPS Tote Plate for SP100-5, 1/2” Pumps............................... $ 119.00 FR KITS05 Wall Mount Bracket for SP100-5, 1/2” Pumps................ 28.00 FR KITS10W Wall Mount Bracket for SP100-10, 1” Pumps................. CALL FR KITS05F Filter/Regulator Assembly for SP100-5, 1/2” Pumps...... 108.00 FR KITS10F Filter/Regulator Assembly for SP100-10, 1” Pumps.......... 195.00 FR KITS05M Muffler for SP100-5 & SP100-10 Pumps........................ 12.00

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E1046


Electric Diaphragm Pumps

79

Motor Driven Diaphragm Pumps

Pumps are available in either 115 volt or 12 volt, (230 and 24 volt on special request). Pumps are available in two styles:

12-Volt/115-Volt • Capacities to 7 GPM • Pressures to 150 PSI These pumps are the perfect choice for chemical transfer, carpet cleaning, car/truck wash applications, livestock cooling and many more. Excellent self-priming capabilities and can be run dry. Diaphragms and check valves are available in Buna, Santoprene®, EPDM and Viton® as noted. Available in either Demand or Bypass styles. (Note: Many models are available in addition to those shown below - Call for Pricing & Availability).

Bypass

Pump continues to run and internally bypasses if discharge is partially or fully closed.

Demand

Pressure switch auto-matically starts and stops pumps at specific pressure settings.

Demand Pumps are supplied with pressure actuated switches that provide on/off control within certain pressure ranges. Bypass Pumps are designed to internally bypass when discharge is closed or partially closed. 115 Volt Demand Pumps with Pressure Switch

* Max. Pressure Part No. Volts GPM Control On Off Internals Ports Net Ea. FJ 2135-032 115 V 1.50 Demand 40 70 Santo/EPDM 1/4" FPT $ 145.50 FJ 3711-032A 115 V 1.50 Demand 70 100 Santo/Viton® 3/8" FPT 113.50 FJ 3811-033A 115 V 1.50 Demand 100 150 Santo/Viton® 3/8” FPT 139.00 FJ 3811-043A 115 V 1.50 Demand 100 150 Santo/EPDM 3/8” FPT 135.00 FJ 2100-032 115 V 1.70 Demand 45 60 Santo/EPDM 3/8” FPT 145.50 FJ 2130-533 115 V 1.80 Demand 60 95 EPDM 1/4” FPT 179.00 FJ 2100-022 115 V 1.85 Demand 45 60 Viton®/Viton® 3/8” FPT 164.00 FJ D3635E7011A 115 V 1.90 Demand 60 100 EPDM 3/8” FPT 125.00 FJ D3835V5011 115 V 2.0 Demand 45 60 Viton®/Viton® 3/8” FPT 130.50 FJ 2130-032 115 V 2.0 Demand 60 95 EPDM 1/4” FPT 179.00 FJ 4300-042 115 V 3.0 Demand 30 45 Santo/EPDM 1/2” HB 111.50 FJ 4300-501A 115 V 3.0 Demand 30 45 Santo/Viton® 1/2” HB 145.00 FJ 4300-043 115 V 4.5 Demand 30 45 Santo/EPDM 3/4” HB 105.50 * Open Flow Discharge.

D

3711 Series

12 Volt Demand Pumps with Pressure Switch

* Max. Part No. Volts GPM Control FJ LF122202 12 V 1.0 Demand FJ LFP122201D 12 V 1.0 Demand FJ 3711-142A 12 V 1.5 Demand FJ 3711-132A 12 V 1.5 Demand FJ 3811-143A 12 V 1.5 Demand FJ 3811-133A 12 V 1.5 Demand FJ 2135-561 12 V 1.9 Demand FJ 2135-132 12 V 1.9 Demand FJ 2100-122 12 V 2.5 Demand FJ 4300-500 12 V 3.0 Demand FJ 4300-143 12 V 4.5 Demand FJ 4300-504 12 V 4.5 Demand FJ R7300142A 12 V 7.0 Demand FJ R7300132A 12V 7.0 Demand * Open Flow Discharge.

Pressure On Off Internals Ports Net Ea. 25 35 Santo/EPDM 3/8" HB $ 52.85 25 35 Santo/Viton® 3/8" HB 54.90 70 100 Santo/EPDM 3/8” FPT 110.00 70 100 Santo/Viton® 3/8” FPT 113.50 100 150 Santo/EPDM 3/8” FPT 127.50 100 150 Santo/Viton® 3/8” FPT 129.50 40 70 Buna/Viton® 1/4” FPT 131.00 40 70 Santo/EPDM 1/4” FPT 126.00 45 60 Viton®/Viton® 3/8” FPT 138.50 30 45 Santo/Viton® 1/2” HB 101.50 30 45 Santo/EPDM 3/4” HB 127.00 30 45 Santo/Viton® 3/4” HB 98.25 50 80 Santo/EPDM 3/4” HB 342.00 50 80 Viton®/Viton® 3/4” HB 349.50

D

2100-032

D

Bypass Pumps with Internal Flow Bypass Part No. Volts FJ D1625F1411 115 V FJ D3835V1311 115 V FJ D3635E1411A 115 V FJ D21X003 12 V FJ D3131V5011 12 V FJ D2131I1311A 12 V FJ D3135E7011A 12 V

Max. GPM 1.4 2.0 2.0 1.6 1.6 1.8 2.0

Max. PSI Internals 70 Santo/Viton® 50 Viton®/Viton® 100 EPDM 60 Santo/Viton® 60 Viton®/Viton® 50 Buna/Viton® 100 EPDM

4300-500

Ports 3/8" FPT 3/8" FPT 3/8” FPT 3/8” FPT 3/8” FPT 3/8” FPT 3/8” FPT

Net Ea. $ 115.00 119.00 115.50 95.75 99.95 100.50 118.00 D

Pumps with No Switches or Bypass Part No. Volts FJ 2100-910 12 V FJ D31X015F 12 V

Max. PSI Internals Ports 60 Buna 3/8" FPT 50 Buna 3/8" FPT

Max. GPM 1.9 2.0

FLOJET Repair Kits Check Valve Kit, 2100/2135 Series, EPDM................. Check Valve Kit, 2100/2135 Series, VITON® ............. Check Valve Kit, 2130/2135 Series, EPDM ................ Check Valve Kit, 4300 Series, VITON® ...................... Check Valve Kit, 4300 Series, EPDM ......................... Diaphragm Kit, 4300 Series, SANTOPRENE® .......... Diaphragm Kit, 2100/2130 Series, VITON® ............... Diaphragm Kit, 2100/2130 Series, EPDM .................. Diaphragm Kit, 2100/2130 Series, SANTOPRENE® . Pressure Switch, 45 PSI ............................................ Pressure Switch Kit, All Demand Pumps, 60 PSI ...... Pressure Switch Kit, All Demand Pumps, 95 PSI ......

R7300142A

Polypropylene Quick Connect Fittings

Repair Kits Part No. FJ 20914-003A FJ 20028-035 FJ 20028-053 FJ 20407-020 FJ 20407-030 FJ 20403-040 FJ 21010-101 FJ 21010-103 FJ 21010-104 FJ 2090103 FJ 2095100 FJ 2090115

Net Ea. $ 124.00 102.50

Net Ea. $ 11.45 21.35 15.30 30.05 17.45 15.20 31.05 16.35 16.10 31.65 31.65 31.65

for Flojet 4000 & G Series & Aquatec Pumps EPDM Elastomers Standard

D

Part No. Net Ea. FJ 20381-026 Quick Conn. x 3/8" HB Straight, Pair...... $ 3.26 FJ 20381-002 Quick Conn. x 1/2” HB Straight, Pair...... 3.26 FJ 20381-003 Quick Conn. x 5/8" HB Straight, Pair...... 2.81 FJ 20381-006 Quick Conn. x 3/4" HB Straight, Pair...... 3.26 FJ 20381-009 Quick Conn. x 1/2" HB, 90˚, Pair............ 3.26 FJ 20381-010 Quick Conn. x 3/4" HB, 90˚, Pair............ 3.26 FJ 20408-000 Side Clips - Package of 2....................... 5.58 Viton® & Other Styles Available

Viton® is a registered trademark of DuPont Performance Elastomers - ®Santoprene is a registered trademark of Mansanto Co.

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0797


Electric Diaphragm Pumps

80

DIAPHRAGM PUMPS 12-VOLT/115-VOLT/24 VOLT

#2088-343-135

Capacities to 7.0 GPM • Pressures to 100 PSI ShurFlo Pumps for a wide variety of low pressure applications. Pumps are available in 12/24/115V with EPDM, Viton® or Santoprene internals. Adjustable demand switch for automatic shut-off or internal by-pass without a switch. Maximum temperature is 170° F. Note: Pumps are not warranted for chemical compatibility. Self-priming to 8’. Buna is the best choice for petroleum products.

D

#8000-543-250

D D

SLV10 Series D

#4211-035

Many Other Models Available! Max. * Max. Cut out Cut In Max. Operating Part No. Volts GPM Control Pressure Pressure Pressure Ports SU SLV10-AA40 ** 12-DC 0.88 Demand & On/Off 25 40 30 PSI 3/8” HB SU SLV10-AA41 ** 12 DC 0.88 Demand 25 40 30 PSI 3/8” HB SU 100-000-21 12-DC 1.0 No Switch NA 10 15 PSI 3/8” HB SU 4211-035 ** 12-DC 6.25 Demand 45 30 40 PSI 1/2” MPT SU 2088-313-145 12-DC 3.6 Demand 45 25 40 PSI 1/2” MPT SU 2088-343-135 12-DC 3.0 Demand 45 25 40 PSI 1/2” MPT SU 2088-343-500 12-DC 3.3 No Switch NA NA 50 PSI 1/2” MPT SU 2088-443-144 12-DC 3.5 Demand 45 25 40 PSI 1/2” MPT SU 2088-474-144 24-DC 3.0 Demand 45 NA 40 PSI 1/2” MPT SU 2088-514-144 12-DC 4.0 Demand 45 25 40 PSI 1/2” MPT SU 2088-514-500 12-DC 4.0 By-Pass 45 NA 50 PSI 1/2” MPT SU 2088-594-154 115-AC 3.3 Demand 45 25 40 PSI 1/2” MPT SU 5050-1311D011 12-DC 5.0 Demand 60 NA 60 PSI 1/2” MPT SU 5050-2301G011 24-DC 5.0 By-Pass 50 40 65 PSI 1/2” MPT SU 8000-151-296 24-DC 1.0 Demand 60 45 60 PSI 3/8” FPT SU 8000-343-236 12-DC 1.2 Demand 60 45 60 PSI 3/8" FPT SU 8000-532-256 115-AC 1.4 Demand & ByPass 60 45 60 PSI 3/8" FPT SU 8000-533-236 115-AC 1.4 Demand 60 45 60 PSI 3/8" FPT SU 8000-533-250 115-AC 1.4 By-Pass 45 NA 50 PSI 3/8" FPT SU 8000-543-236 12-DC 1.8 Demand 60 45 60 PSI 3/8” FPT SU 8000-543-238 12-DC 1.8 Demand 100 80 100 PSI 3/8” FPT SU 8000-543-250 12-DC 1.8 By-Pass 45 NA 40 PSI 3/8” FPT SU 8000-633-236 115-AC 1.4 Demand 60 45 60 PSI 3/8" FPT SU 8000-643-236 12-DC 1.5 Demand 60 45 60 PSI 3/8" FPT SU 8000-812-288 115-AC 1.3 Demand & Bypass 100 80 100 PSI 3/8” FPT SU 8000-813-238 115-AC 1.6 Demand 100 80 100 PSI 3/8” FPT SU 8005-233-236 115-AC 1.5 Demand 60 45 60 PSI 3/8" FPT SU 8005-733-255 115-AC 1.5 Demand 60 45 60 PSI 3/8” FPT SU 8030-813-239 12-DC 1.5 Demand 150 80 150 PSI 3/8” MPT SU 8030-863-239 115-AC 1.5 Demand 150 80 150 PSI 3/8” FPT SU 8030-863-299 115-AC 1.5 Demand & Bypass 150 80 150 PSI 3/8” FPT * Open Flow.

** Intermittent Use Only.

Pumps are available in either 115 volt or 12 volt, (230 and 24 volt on special request). Pumps are available in two styles: Bypass Pump continues to run and internally bypass if discharge is partially or fully closed. Demand Pressure switch automatically starts and stops pumps at specific pressure settings.

SERVICE & REPAIRS Did you know? We can service almost every brand of pump we sell in our catalog. Call us at 1-800-228-9666 (Omaha, NE) for a quote!

Part No. SU 94-395-05 SU 94-395-06 SU 94-238-04 SU 94-238-03 SU 94-232-00 SU 94-232-05 SU 94-390-05 SU 94-390-08 SU 94-391-09 SU 94-231-05 SU 94-375-05 SU 94-230-40 SU 255-323

Valves Diaphragm Net Ea. Viton® Santoprene $ 44.70 Viton® Santoprene 42.05 EPDM Nitrile 34.75 Viton® Santoprene 218.00 Viton® Santoprene 153.00 Viton® Santoprene 93.55 Viton® Santoprene 89.40 Santoprene Santoprene 81.90 Santoprene Santoprene 83.00 Santoprene Santoprene 133.00 Santoprene Santoprene 125.50 Santoprene Santoprene 105.50 Viton® Santoprene 135.00 EPDM Santoprene/Poly 280.00 Buna Geolast 94.65 Viton® Viton® 101.00 Viton® Santoprene 104.00 Viton® Santoprene 106.00 Viton® Santoprene 99.00 Viton® Santoprene 66.50 Viton® Santoprene 78.70 Viton® Santoprene 72.15 Buna Geolast 101.00 Buna Geolast 88.15 Viton® Santoprene 121.50 Viton® Santoprene 115.00 EPDM Santoprene 91.75 EPDM Santoprene 90.20 Viton® Santoprene 118.50 Viton® Santoprene 129.50 Viton® Santoprene 136.00

SHURflo REPAIR KITS & Accessories Net Ea. Diaphragm Kit, Viton®, for 8000 Series ............ $ 40.80 Diaphragm Kit, Santoprene, for 8000 Series...... 13.40 Diaphragm Kit, Santoprene, for 2088 Series...... 24.75 Diaphragm Kit, Santoprene, for 4111 & 4211..... 24.75 Valve Kit, Santoprene, for 2088 Series............... 12.95 Valve Kit, Viton®, for 2088, 4111 & 4211 Series 34.65 Valve Kit, Viton®, for 8000 Series ..................... 29.75 Valve Kit, EPDM, for 8000 Series....................... 16.30 Valve Kit, Viton®, for 8000 By-Pass Series ...... 34.10 Pressure Switch Kit for 2088 Series................... 38.75 Pressure Switch Kit for 8000 Series .................. 19.35 Pressure Switch Kit for 4111 & 4211.................. 21.50 1/2" 50 Mesh Inlet Strainer ................................ 10.95 Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0050


Pumps

81

12-Volt “FatBoy” Pumps

Transfer Pump 12-Volt

Fatboy Diaphragm Pumps feature self-priming design with priming capacity to 14’. Available in either Demand or Bypass styles. Nylon housing with Viton® valves and Santoprene diaphragms for added chemical compatibility. Rated to 7 GPM maximum flow. Motors are 12VDC, totally enclosed, non-vented. Maximum temperatures to 140° F. Lead wires are 14AWG. 12” long. Ports are 1/2” FPT.

D

- Can Run Dry Maximum Flow Part No. Control PSI @ 60 PSI Wt.

AQ 770 AQ 771

Demand Bypass

60 70

5 GPM 5 GPM

8 lbs. 8 lbs.

Net Ea.

Pony Transfer Pumps are lightweight, non-submersible and portable. Can be used for transfer and dewatering at low pressure (10 PSI). Rated for intermittent duty (15 minutes on, 45 minutes off). Self-priming up to 6’. Plated brass bodies. Dual ports with 3/4” male garden hose x 3/8” FPT. 1/10 H.P. 12-Volt units come with 6” lead wires. 110-volt comes with 5’ power cord.

UL

Part No. Voltage * Flow Rate Wt Net Ea. SR M40 Utility Pump 115 Volt 4 GPM 6 lbs. $ 89.95 SR A252 Impeller kit for M40 pump....................................... 14.60 * Flow rate is based on 10' discharge height.

12-Volt Aqua Tiger Pumps FEATURES: • 12-Volt DC Centrifugal Pumps • 3/4" Ports/Viton® Seal • Low Flow/Pressure 5 GPM @ 9 PSI Maximum Flow 18 GPM • Bronze Body & Impeller or 316 Stainless Body/Impeller • Maximum temperature is 140˚ F.

Part No. Voltage Description HY 9700B 12 Volt DC Bronze Centrifugal Pump SR COMSV012D 12 Volt DC Stainless Centrifugal Pump

$ 133.00

Pony Pumps

D

12V & 115V

D

Part No.

Voltage

GPM

Wt.

GJ PP1 GJ PP12

115 Volt 12 Volt

6.0 5.0

5.5 lbs. 4.2 lbs.

Net Ea.

$ 104.00 96.20

12-Volt Diaphragm Pumps For use with a wide variety of applications Fatboy Diaphragm Pumps feature self-priming design with priming capacity to 14’. Available in either Demand or Bypass styles. Nylon housing with Viton® valves and Santoprene diaphragms for added chemical compatibility. Rated to 7 GPM maximum flow. Motors are 12VDC, totally enclosed, nonvented. Maximum temperatures to 140° F. Lead wires are 14AWG. 12” long. Ports are 1/2” FPT.

Wt. Net Ea. 5 lbs. $ 196.50 5 lbs. 251.50

12 Volt High Head Utility Pump

D

1 HP, 12 Volt motor provides high pressures for wash down and many other applications where 120 Volt power is not available. Available in either investment cast iron or stainless housing. Stainless enclosed impellers & shaft are standard. Discharge rotates in 90° increments; includes 4 drain plugs. Rated to 180° F. with buna seal; 200° F. with viton seal. 5 GPM at 33 PSI, 25 GPM at 26 PSI, 50 GPM at 10 PSI. 1 1/4” x 1” FPT ports. Straight centrifugal (not D self-priming). 1 Hour Duty Rating: 83 amps maximum. Mech. Seal Buna N Viton®

Net Ea.

GJ 350M 115-Volt Transfer Pump

M40

Model M40 is UL listed and features a 115 volt motor with thermal overload protection and grounded 6' power cord with plug. Rated to 4 GPM @ 10' discharge height.

Housing Cast Iron Stainless

Features Include: Nylon pumping head with Ryton impeller • Carbon/Ceramic seal • Buna O-Ring • Ports are 3/8" hose barb • 1/8" Bypass port • Rated to 115-volt • 1/10 H.P. • 24" lead wires (does not include switch) • Dimensions: 4" Width, 7" Length, 3" Height • Weight is 2.7 lbs.

Part No.

Light-duty, Economical Utility Pumps for a wide variety of transfer requirements. Features non-corrosive pump end with stainless steel wear plates. Inlet and outlet ports are 3/4" MGHT.

Part No. GR 489G-95 GR 489G-98

D

Ideal for mild chemical transfer and carpet cleaning applications. Non-submersible design is not self-priming and requires a flooded suction. Rated to a maximum of 2.85 GPM and up to 35 PSI.

$ 256.00 256.00

Utility Pumps

D

Model 350M

Part No. GPM Ports Control Net Ea. AQ 550 5.0 1/2" FPT Demand $ 126.50 AQ 550-HB 5.0 1/2” Quick Tach * Demand 126.50 AQ 551 5.0 1/2” FPT Bypass 128.00 AQ FQ5S-12 1/2” Straight QT Hose Barb Fitting.... 4.18 * Model 550HB requires use of QuT hose barb connectors.

Wt 57 lbs. 57 lbs.

Net Ea. $ 803.84 1011.22

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0711


Peristaltic Pumps

82

Peristaltic Metering Pumps STENNER Peristaltic Pumps are designed to offer accurate dosing of chemicals and solutions to a wide variety of industrial applications. Self-priming to 25’. Roller tube design offers precise adjustable injection rates from 5 to 100% concentrations. Pressures to 100 PSI and temperatures to 125° F. Standard tubes are 1/4” O.D (3/8” also available). Tube construction is Santoprene but Tygothane tubes are also available for petroleum products, oils and solvents. Available in single, double and triple head designs for multiple chemicals or higher flow rates. Motors are 120V, 60Hz but 230V 50 or 60Hz are also available. Tanks are available in 7, 15 or 30 gallon sizes in translucent white or UV resistant gray. Tanks also come with grommets and mounting screws. Pre-assembled pump/tank systems are also available in many different configurations. All pumps are rated for continuous duty. Classic 85 Series

Tank/Pump Package

D

D

Classic 85 Series Pumps feature adjustable output from 5 to 100% in 2.5% increments with a dial gear adjustment. Six interchangeable tubes. Dimensions are 5” x 8” x 6”. Rated to 100 PSI, 40 GPD and 44 RPM.

Pump/Motor Units Part No. UB 85MJH1A1S UB 85MJH2A1S UB 85MJH7A1S

Oz./Min. .03 - .44 .07 - 1.51 .18 - 3.55 Gallons 7.5 7.5 15 15

D

D

SVP Series Pumps feature adjustable output from 5 to 100% in 1% increments with a digital keypad adjustment. Six interchangeable tubes. Dimensions are 5” x 6” x 10”. Rated to 100 PSI, 44 GPD and 47 RPM.

Pump/Motor Units Tube Santoprene Santoprene Santoprene

Wt. 9 lbs. 9 lbs. 9 lbs.

Net Ea. $ 298.00 298.00 298.50

Wt. 9 lbs. 9 lbs. 19 lbs. 19 lbs.

Net Ea. $ 102.00 102.00 119.50 119.50

Part No. Oz./Min. UB SVP1H1A1S .03 - .44 UB SVP1H2A1S .07 - 1.51 UB SVP1H7A1S .18 - 3.55

Tanks for Classic Series Pumps Part No. UB STS7NC UB STS7GC UB STS15NC UB STS15GC

UV Gray Tank

SVP Series

Tube Santoprene Santoprene Santoprene

Wt. 9 lbs. 9 lbs. 9 lbs.

Net Ea. $ 508.00 508.00 508.00

Wt. 9 lbs. 9 lbs. 19 lbs. 19 lbs.

Net Ea. $ 113.00 113.00 128.50 128.50

Tanks for SVP Series Pumps

Color White Gray White Gray

Part No. UB STS7N02 UB STS7G02 UB STS15N02 UB STS15G02

Peristaltic Injector Pumps Peristaltic Injector Pumps are the ideal choice for injecting tough-tohandle solutions that can foul conventional Pumps with check valves. Peristaltic pumps feature rollers that compress tubes in a progressive squeezing action. Precision injection at 50-100 PSI.

Gallons 7.5 7.5 15 15

Color White Gray White Gray

dultmeier.com

Standard Features: 110 Volt, ball bearing motors (230 volt available) • selfpriming, even against line pressure • Solid-state feed controller with 1 minute cycle • Chemical-resistant, thermoplastic, weatherproof housing • No valves or seals, tubes are the only wetted parts • Ports are designed for O.D. tubing • Pumps tubes are Norprene • Power cord and plug are standard • Rated to 5000 Centipoise and up to 110° F. • Rated for continuous duty and 50% solids by volume • Dimensions are: 6-1/8" H x 10-1/8" W x 9" D. • Ship weight is 8 lbs.

D 3/8" Compression Fittings

A100N Standard Model

Maximum Tubing Maximum Part No. Rate Control Oz/Min. Ports PSI

BL A1N00A4T BL A1N00A6T BL A1N10A6T BL A1N30A6T BL A1N10A7T

1 Min. % Dial 1 Min. % Dial 1 Min. % Dial 1 Min. % Dial 1 Min. % Dial

0.20 0.61 1.42 2.67 4.66

• Shop and Order On-Line 24 Hours a Day, 7 Days a Week! • Large Inventories of Over 3 Million Total Items! • View Current Pricing! • Web Specials and Bargain Corner! • Know Your Part Numbers? Use the Web Quick Order Page!

Net Ea.

1/4” 100 $ 326.00 3/8” 100 326.00 3/8” 100 326.00 3/8” 75 326.00 7/16” 50 326.00

(800) 228-9666

• Technical Library packed with information! • See New Items not Shown in Our Printed Catalogs! • Track Your Order Status and History! • Secure Site for Safe On-Line Ordering.

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES • OMAHA, NE

• Hundreds of Parts List Schematics (and more to come!)

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0900


Injection Pumps • Pump/Tank Systems

83

Injection Pumps

Pump/Tank Systems

Adjustment Dial

The Star Systems from Blue White feature the popular C15N Diaphragm Pumps with a 15 gallon storage tank. One unit for convenient chemical injection. Units are pre-plumbed and ready-to-use. Tanks feature a rectangular design for floor or table placement. Lid allows for opening, closing or venting. The most popular pumps are shown, but many other pump/tank models are available. Pumps are rated to 125 PSI. Dimensions are 22" high x 15-1/2" wide x 19-1/2" deep.

D

C1700N Series (Dual Head)

D

C1500N Series D

Blue-White Diaphragm Metering Pumps. Ideal for dispensing a precise and wide variety of solutions. (Single and Dual Head Units can apply different chemicals or the same chemical at different rates to different points.)

Double Ball Cartridge Valves Part No.

Standard Features include the following: • Weather-resistant housing for in­door or outdoor use • Easy to adjust feed rate; you always know exactly what your injection rate is • PVDF (Kynar) Pump heads • Double-sealed PVDF cartridge fittings • Pressures to 125 psi (70 PSI on 10 oz. and Larger) • Chemically resistant internals • Anti-siphon check valve and foot valve strainer • ETL Listed • Can be wall or shelf mounted • Viton® O-ring & Teflon/EP Diaphragm • 115 or 24 Volt (230 volt also available) • Minimum output is 5% of maximum shown • Dimensions: 9-1/16" H x 4-1/2" W x 5-3/4" D on Model C1500N. 9-1/2" H x 7-1/2" W x 4" D on Model C1700N • Maximum fluid temperature is 130° F. Includes 3/8” OD suction and discharge tubing, flow indicator and mounting hardware.

Part No.

Max. Oz. Per Minute

Voltage

BL C15N202X06 1.00 115 BL C15N302X06 1.49 115 BL C15N202X 2.40 115 BL C15N302X 2.70 115 BL C15N402X 6.10 115 BL C15N404X † 10.15 115 BL C15N232A06 1.00 24 BL C15N332A06 1.49 24 BL C15N232A 2.40 24 BL C15N332A 2.70 24 BL C15N432A 6.10 24 BL C17N202X * 5.12 115 BL C17N302X * 6.20 115 BL C17N402X * 12.16 115 BL C17N404X * 21.60 115 BL C17N483X * 33.60 115 * Dual Head Units. † Maximum of 70 PSI.

Part No. BL K568-6E BL K568-6A BL C-406VT-15N BL C-406T-15N BL C-340A BL C-340E BL A-014PHD-6V BL C-535A6-6E BL C-535A6-6

Wt.

Net Ea.

9 lbs. 9 lbs. 9 lbs. 9 lbs. 9 lbs. 9 lbs. 9 lbs. 9 lbs. 9 lbs. 9 lbs. 9 lbs. 11 lbs. 11 lbs. 11 lbs. 11 lbs. 11 lbs.

$ 275.00 269.00 275.00 267.50 268.00 268.00 275.00 269.00 275.00 269.00 281.50 405.00 405.00 405.00 405.00 399.00

BL T15N102X15 BL T15N302X15 BL T15N402X15 BL T15N404X15

Max Oz/Min

Tank

Voltage

1.70 1.40 5.90 10.60

15 gallon 15 gallon 15 gallon 15 gallon

115 115 115 115

Wt.

Net Ea.

27 lbs. $ 439.00 27 lbs. 439.00 27 lbs. 439.00 27 lbs. 439.00

* 24 Volt Models available on request.

XP Pumps XP Pumps from Cat Pumps are an ideal choice for carpet extractors, Misting/cooling, hydrostatic testing and truck mount applications. Patented, greaseless design for added life, serviceability and performance. Pump and Motor Combinations are rated from 0.5 to 2.0 GPM and 100 to 800 PSI. Standard motors are 1/3, 1/2 or 3/4 HP, single phase, 120/240 volt. Pumps feature ceramic plungers, stainless valves, Viton® seals and aluminum housings. Easy drain out feature is also standard.

D

Part No.

GPM

PSI

HP

CC 1XP050.031 0.50 800 1/3 CC 1XP075.031 0.75 650 1/3 CC 1XP085.031 0.85 600 1/3 CC 1XP100.031 1.00 500 1/3 CC 1XP125.031 1.25 400 1/3 CC 1XP150.031 1.50 325 1/3 CC 1XP200.031 2.00 250 1/3 CC 1XP085.051 0.85 800 1/2 CC 1XP100.051 1.00 800 1/2 CC 1XP125.051 1.25 600 1/2 CC 1XP150.051 1.50 500 1/2 CC 1XP200.051 2.00 400h 1/2 CC 1XP125.071 1.25 800 3/4 CC 1XP150.071 1.50 700 3/4 CC 1XP200.071 2.00 500 3/4 CC 7085 Unloader, .5 - 6.5 GPM & 1000 PSI

Replacement Parts for C1500N Pumps Net Ea. Bullet Valve Kit with 3/8" OD top & bottom fitting & "EP" seal, Pack of 2............... $ 60.15 Bullet Valve Kit with 3/8" OD top & bottom fitting & Viton® seal, Pack of 2............ 60.15 Diaphragm Assembly, "Viton®".......................... 35.20 Diaphragm Assembly, "EPDM"........................... 26.60 Foot Valve "Viton®" ................................. 21.55 Foot Valve "EPDM" ................................. 21.55 Anti-siphon valve for 3/8" OD tubing, "Viton®"... 28.50 Complete Liquid End - "EPDM".......................... 76.55 Complete Liquid End - "Viton®"......................... 78.85

Wt.

25 lbs. 25 lbs. 25 lbs. 25 lbs. 25 lbs. 25 lbs. 25 lbs. 30 lbs. 30 lbs. 30 lbs. 30 lbs. 30 lbs. 35 lbs. 35 lbs. 35 lbs. 1 lbs.

Call Toll Free For Prices

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0052


Vacuum Pumps Vacuum Power Packs

Vacuum Pumps Conde Vacuum Pumps are rated from 35 to 230 CFM. Designed for tanks from 50 to 2500 gallons. Available in Vacuum only or Vacuum/Pressure models. Vacuum only pumps are an economical option when pressure is not required for off-loading. All units can be driven by a variety of sources such as gas engine, PTO, hydraulic, gear box or 12 volt clutch. All pumps are available for clockwise or counterclockwise rotation as noted.

Vacuum only or Vacuum/Pressure Power Packs featuring Conde Vacuum Pumps shown on this page. All pump units are standard with Honda Gas Engines, stainless steel baseplates, stainless belt guards, dual groove pulleys and vacuum relief valves. Engines are shown with or without electric start as noted. All units are pre-assembled and ready for installation to your tank or truck. Standard With: PMS6AV PowerPak Vacuum/Pressure

Pumps shown below come standard with automatic oilers that require no adjustments. Compact, low profile design allows for ease-of-installation. Sealed bearings require no maintenance. All pumps are rated to 28” of intermittent vacuum and 20” continuous vacuum. Pumps with pressure option are rated to 20 PSI discharge. Pro3, Super6 and SDS6 models include vacuum relief valves. All pumps are tested prior to shipping and carry a 1-Year Warranty. (Specify tapered shafts if clutch drive is required). SPECIFICATIONS PUMP SERIES Speed Range Shaft Size Port Size Pro3 1200-1750 3/4” 1” Super6 1200-1750 1” 1-1/4” SDS6 1200-1750 1” 1-1/2” SDS12 1200-1750 1-1/8” 1-1/2” ULTRA12 1200-1750 1-1/8” 1-1/2” PRO3 Vacuum Only - 35 CFM -

Ideal Tank Size 50-300 Gallon 300-500 Gallon 500-1000 Gallon 1000-2000 Gallon 1200-2500 Gallon

D

Ideal for tanks from 200 - 500 gallons ESTIMATED TANK PULL DOWN TIME (15” Hg) TANK SIZE SDS12 SDS6 Super6 ProVac3 100 Gallon - - 8 sec. 16 sec. 200 Gallon - - 17 sec. 37 sec. 300 Gallon - - 25 sec. 50 sec. 400 Gallon - - 34 sec. 64 sec. 500 Gallon 16 sec. 26 sec. 52 sec. 84 sec. 750 Gallon 24 sec. 40 sec. - 1000 Gallon 32 sec. 53 sec. - 1500 Gallon 50 sec. 80 sec. - 2000 Gallon 67 sec. 106 sec. -

Ideal for tanks from 300 - 500 gallons

Vacuum Only Pumps

Pump Series Pro3 Pro3 Super6 Super6 SDS6 SDS6 SDS12 SDS12 Ultra12 Ultra12

Vacuum 35 cfm 35 cfm 70 cfm 70 cfm 115 cfm 115 cfm 190 cfm 190 cfm 230 cfm 230 cfm

PMS6V PowerPak Vacuum Only

Ideal for tanks from 1000 - 2000 gallons

D

D

Part No. CO OL3PW CO OL3PC CO OL6SW CO OL6SC CO OL6SDSW CO OL6SDSC CO OL12SDSW CO OL12SDSC CO OL12ULW CO OL12ULC

• Honda Gas Engines • Stainless Steel Baseplates • Stainless Belt Guards • Dual Groove Pulleys • Vacuum Relief Valves

D

SUPER6 Vacuum Only - 70 CFM -

Ideal for tanks from 50 - 300 gallons

84

Rotation Clockwise Counterclock Clockwise Counterclock Clockwise Counterclock Clockwise Counterclock Clockwise Counterclock

Wt. 40 lbs. 40 lbs. 75 lbs. 75 lbs. 100 lbs. 100 lbs. 150 lbs. 150 lbs. 165 lbs. 165 lbs.

Part No. Pump Series Engine DU PM3V Pro3 4 HP, Rope Pull DU PM3AV Pro3 5-1/2 HP, Rope Pull DU PMS6V Super6 5-1/2 HP, Rope Pull DU PMS6AV Super6 5-1/2 HP, Rope Pull DU PMSD6V SDS6 9 HP, Electric DU PMSD6AV SDS6 9 HP, Electric DU PMSD12V SDS12 13 HP, Electric DU PMSD12AV SDS12 13 HP, Electric

Net Ea. $ 733.00 733.00 1081.00 1078.00 1218.00 1218.00 1425.00 1425.00 1691.00 1691.00

Vac/Pressure Vac Vac/Pressure Vac Vac/Pressure Vac Vac/Pressure Vac Vac/Pressure

Wt. Net Ea. 112 lbs. $ 1858.00 112 lbs. 2197.00 155 lbs. 2325.00 155 lbs. 2472.00 225 lbs. 2959.00 225 lbs. 3254.00 290 lbs. 4281.00 290 lbs. 3672.00

Accessories Oil Catch Mufflers are designed to capture oil and muffle exhaust as it exits the pump.

SDS6 & SDS12 Vacuum/Pressure - 115 CFM -

Model MF3 is for model Pro3 pumps and is rated up to 40 cfm. Construction is steel.

ULTRA12 Vacuum/Pressure - 230 CFM -

D

Model MF3612 is for Super6, SDS6, SDS12 and Ultra12 pumps and is rated to 200 cfm. Construction is aluminum. Part No. Ports CO MF3 1” CO MF3612 1-1/2”

D

Max. CFM 40 200

D

MF3 Oil Catch Muffler

Wt. 15 lbs. 25 lbs.

MF3612 Oil Catch Muffler

Net Ea. $ 155.50 259.00

D

Ideal for tanks from 500 - 1000 gallons

Vacuum/Pressure Pumps

Part No. CO HD3PW CO HD3PC CO HD6SW CO HD6SC CO HD6SDSW CO HD6SDSC CO HD12SDSW CO HD12SDSC CO HD12ULW CO HD12ULC

Pump Series Vacuum Pressure Pro3 35 cfm 20 PSI Pro3 35 cfm 20 PSI Super6 70 cfm 20 PSI Super6 70 cfm 20 PSI SDS6 115 cfm 20 PSI SDS6 115 cfm 20 PSI SDS12 190 cfm 20 PSI SDS12 190 cfm 20 PSI Ultra12 230 cfm 20 PSI Ultra12 230 cfm 20 PSI

M1SS Secondary Moisture Trap

Ideal for tanks from 1200 - 2500 gallons

Rotation Clockwise Counterclock Clockwise Counterclock Clockwise Counterclock Clockwise Counterclock Clockwise Counterclock

DULTMEIER SALES • OMAHA, NE

Wt. Net Ea. 40 lbs. $ 1021.00 40 lbs. 1021.00 75 lbs. 1209.00 75 lbs. 1209.00 100 lbs. 1351.00 100 lbs. 1351.00 150 lbs. 1568.00 150 lbs. 1568.00 165 lbs. 1823.00 165 lbs. 1823.00

(800) 228-9666

D

Secondary Moisture Trap is designed to remove moisture and debris that may get past the primary shut-off. Model M1SS Features 1-1/2” FPT ports and stainless steel construction. Rated up to 200 cfm. Part No. CO M1SS

Ports 1-1/2”

Max. CFM 200

Mount Drive Base for use with right angle gear boxes. Easily bolts to truck frame. Can be used with any of the SDS pumps, either vacuum or vac/pressure. Heavy construction and CNC machined for extra strength. Dimensions are 26”L x 17-3/4” H x 10” W. Part No. CO 1RA Right Angle Drive Base •

www.dultmeier.com

• DAVENPORT, IA

Wt. 58 lbs.

Wt. 23 lbs.

D

Net Ea. $ 339.50

1RA Right Angle Drive Base

Net Ea. $ 484.00

(800) 553-6975

E0823


Pressure Booster • Multi-Stage Pumps

85

Pressure Booster Pumps

Booster Pumps

Pressure Booster Pumps for a wide variety of pumping applications. Ideal for increasing rinse water pressure, liquid transfer, spot-free water re-pressurization and many others. Standard construction is Stainless Steel or Cast Iron. (Not Self-priming). Maximum temperature is 160° F. - water only.

APPLICATION FOR:

• Residential, commercial or agricultural pressure wash • Reverse osmosis • Evaporative cooling systems/misters • Booster Service

• Spray systems • Water circulation • Filtration • HVAC • General purpose pumping

Sta-Rite Pressure Booster Pumps are an ideal choice for boosting water pressures for washing, RO rinse water and general purpose pumping. Patented, Multi-stage design. Carbon/Ceramic/Buna shaft seals. Stainless steel pump and motor shaft. Cast iron or Stainless steel inlet and outlet ports. Rated to 140° F. and 80 psi inlet pressure. (Not Self-priming). Suction lifts to 15'.

D

D

Motors are 60HZ, 3500 RPM, TEFC, and are available in either single phase, 115/230 volt or three phase, 208/230/460 volt. Cast Iron Pumps feature cast iron inlet and discharge fittings and 304SS stainless pump shell. Mechanical seal and BUNA elastomers are standard. Stainless Steel pumps feature 304SS stainless steel inlet and discharge fittings and pump shell. Mechanical seal and VITON® elastomers are standard. Part No. Castings Motor Ports * Flow Rate Wt. Net Ea. GL 7GBC1014RO Cast Iron 1hp, 1ph. 1" FPT 5 GPM @ 180 psi 65 lbs. $ 636.02 GL 7GBS1014R4 Stainless 1hp, 1ph. 1" FPT 5 GPM @ 180 psi 65 lbs. 803.19 GL 10GBC1514QO Cast Iron 1.5hp, 1ph. 1" FPT 8 GPM @ 180 psi 56 lbs. 645.90 GL 10GBS1514Q4 Stainless 1.5hp, 1ph. 1" FPT 8 GPM @ 180 psi 56 lbs. 846.96 GL 10GBC2014SO Cast Iron 2hp, 1ph. 1" FPT 12 GPM @ 180 psi 73 lbs. 721.63 GL 10GBS2014S4 Stainless 2hp, 1ph. 1" FPT 12 GPM @ 180 psi 73 lbs. 886.36 GL 10GBC2015SO Cast Iron 2hp, 3ph. 1" FPT 12 GPM @ 180 psi 64 lbs. 705.48 GL 10GBS2015S4 Stainless 2hp, 3ph. 1" FPT 12 GPM @ 180 psi 64 lbs. 868.04 GL 18GBC2014NO Cast Iron 2hp, 1ph. 1" FPT 15 GPM @ 150 psi 73 lbs. 693.18 GL 18GBS2014N4 Stainless 2hp, 1ph. 1" FPT 15 GPM @ 150 psi 73 lbs. 852.95 GL 18GBC2015NO Cast Iron 2hp, 3ph. 1" FPT 15 GPM @ 150 psi 64 lbs. 651.57 GL 18GBS2015N4 Stainless 2hp, 3ph. 1" FPT 15 GPM @ 150 psi 64 lbs. 810.76 GL 18GBC3014QO Cast Iron 3hp, 1ph. 1" FPT 22 GPM @ 130 psi 77 lbs. 905.67 GL 18GBS3014Q4 Stainless 3hp, 1ph. 1" FPT 22 GPM @ 130 psi 77 lbs. 1066.22 GL 18GBC3015QO Cast Iron 3hp, 3ph. 1" FPT 22 GPM @ 130 psi 65 lbs. 905.67 GL 18GBS3015Q4 Stainless 3hp, 3ph. 1" FPT 22 GPM @ 130 psi 65 lbs. 1066.22 GL 45HB25013 †Cast Iron 5hp, 1ph. 2" FPT 30 GPM @ 115 psi 147 lbs. 2409.79 GL 45HB25035 Cast Iron 5hp, 3ph. 2" FPT 30 GPM @ 115 psi 99 lbs. 1578.34 GL 45HB27535 Cast Iron 7.5hp, 3ph. 2" FPT 50 GPM @ 125 psi 150 lbs. 1951.01 GL 45HB21135 Cast Iron 10hp, 3ph. 2" FPT 60 GPM @ 125 psi 190 lbs. 2170.49 * Flow rates can be increased if discharge pressure is decreased. Pump curves available on request. † 208/230 V.

Booster Pumps Pressure Booster Pumps from Flint & Walling. Ideal for increasing water pressure from city mains or private water systems. Also a good choice for reverse osmosis systems, spray or misting units, water circulation and general purpose pumping. Available in cast iron, powder-coated cast iron and stainless steel construction. Motors are 1 Phase or 3 Phase, ODP/60Hz. (50Hz and TEFC motors also available). Cast iron pumps feature Buna shaft seals, stainless pumps have Viton® seals. Noryl impellers and diffusers are standard on all models.

D

Motors are ODP (TEFC available on request). All single phase motors to 2 HP are 115/230 volt. All pumps feature 3/4" FPT inlet and outlet except for HP20 series which are 1" FPT. 3-HP 1-Phase Motors are 208/230 volt. All 3-HP 3-Phase Motors are 208/230/460 volt.

Part No. SA HP10D SA HP10E SA HP7E SA HP10FMS SA HP10G SA HP10G3 SA HP20G SA HP20G3 SA HP20H SA HP20H3 SA HPS7E SA HPS10FMS SA HPS10GMS SA HPS10G3 SA HPS20GMS SA HPS20G3 SA HPS20H SA HPS20H3 SA HP30H SA HP30H3 SA HPS30H SA HPS30H3

Ports Motor * Flow Rate Wt. Net Ea. 3/4" Cast Iron 3/4 hp, 1 ph 10 GPM @ 100 psi 46 lbs. $ 524.00 3/4" Cast Iron 1 hp, 1 ph 10 GPM @ 125 psi 50 lbs. 547.00 3/4" Cast Iron 1 hp, 1 ph 6 GPM @ 180 psi 51 lbs. 578.00 3/4" Cast Iron 1.5 hp, 1 ph 8 GPM @ 180 psi 58 lbs. 619.00 3/4" Cast Iron 2 hp, 1 ph 10 GPM @ 180 psi 63 lbs. 682.00 3/4" Cast Iron 2 hp, 3 ph 10 GPM @ 180 psi 59 lbs. 630.00 1" Cast Iron 2 hp, 1 ph 15 GPM @ 155 psi 62 lbs. 633.00 1" Cast Iron 2 hp, 3 ph 15 GPM @ 155 psi 58 lbs. 547.00 1" Cast Iron 3 hp, 1 ph 20 GPM @ 195 psi 59 lbs. 879.00 1" Cast Iron 3 hp, 3 ph 20 GPM @ 195 psi 55 lbs. 885.00 3/4" Stainless 1 hp, 1 ph 6 GPM @ 180 psi 51 lbs. 750.00 3/4" Stainless 1.5 hp, 1 ph 8 GPM @ 180 psi 58 lbs. 771.00 3/4" Stainless 2 hp, 1 ph 10 GPM @ 180 psi 63 lbs. 850.00 3/4" Stainless 2 hp, 3 ph 10 GPM @ 180 psi 59 lbs. 804.00 1" Stainless 2 hp, 1 ph 15 GPM @ 155 psi 62 lbs. 804.00 1" Stainless 2 hp, 3 ph 15 GPM @ 155 psi 58 lbs. 743.00 1" Stainless 3 hp, 1 ph 20 GPM @ 155 psi 59 lbs. 1075.00 1" Stainless 3 hp, 3 ph 20 GPM @ 155 psi 55 lbs. 1018.00 1-1/4" Cast Iron 3 hp, 1 ph 30 GPM @ 125 psi 59 lbs. 956.00 1-1/4" Cast Iron 3 hp, 3 ph 30 GPM @ 125 psi 55 lbs. 928.00 1-1/4" Stainless 3 hp, 1 ph 30 GPM @ 125 psi 59 lbs. 1106.00 1-1/4" Stainless 3 hp, 3 ph 30 GPM @ 125 psi 55 lbs. 1081.00

FPT * Flow Part No. Material Motor Ports Rate FW PB0512C051 Powder Cast 1/2 HP, 1 PH 3/4” 4 GPM @ 100 PSI FW PB0512S051 Stainless 1/2 HP, 1 PH 3/4” 4 GPM @ 100 PSI FW PB0516C071 Powder Cast 3/4 HP, 1 PH 3/4” 5 GPM @ 140 PSI FW PB0516S071 Stainless 3/4 HP, 1 PH 3/4” 5 GPM @ 140 PSI FW PB1014A101 Cast Iron 1 HP, 1 PH 3/4” 8 GPM @ 140 PSI FW PB1014C101 Powder Cast 1 HP, 1 PH 3/4” 8 GPM @ 140 PSI FW PB1014S101 Stainless 1 HP, 1 PH 3/4” 8 GPM @ 140 PSI FW PB1016A151 Cast Iron 1-1/2 HP, 1 PH 3/4” 10 GPM @ 140 PSI FW PB1016C151 Powder Cast 1-1/2 HP, 1 PH 3/4” 10 GPM @ 140 PSI FW PB1016S151 Stainless 1-1/2 HP, 1 PH 3/4” 10 GPM @ 140 PSI FW PB2711C201 Powder Cast 2 HP, 1 PH 1” 13 GPM @ 140 PSI FW PB2711C203 Powder Cast 2 HP, 3 PH 1” 13 GPM @ 140 PSI FW PB2711S201 Stainless 2 HP, 1 PH 1” 13 GPM @ 140 PSI FW PB2711S203 Stainless 2 HP, 3 PH 1” 13 GPM @ 140 PSI FW PB2714A301 Cast Iron 3 HP, 1 PH 1” 18 GPM @ 160 PSI FW PB2714A303 Cast Iron 3 HP, 3 PH 1” 18 GPM @ 160 PSI FW PB2714S301 Stainless 3 HP, 1 PH 1” 18 GPM @ 160 PSI FW PB2714S303 Stainless 3 HP, 3 PH 1” 18 GPM @ 160 PSI FW PB5506A301 Cast Iron 3 HP, 1 PH 2” 32 GPM @ 80 PSI FW PB5506A303 Cast Iron 3 HP, 3 PH 2” 32 GPM @ 80 PSI

Wt. Lbs. Net Ea. 39 $ 349.50 39 507.00 44 418.50 44 576.00 48 382.00 48 478.00 48 569.00 53 432.00 53 525.00 53 669.00 56 485.50 56 520.00 56 706.00 56 738.00 57 548.00 56 567.00 57 781.00 56 795.00 58 606.00 58 637.00

* Add pressure rates to incoming water pressure for total output pressure, I.E. if incoming pressure is 50 PSI, PB0516 Series will deliver 190 PSI output. Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0056


Submersible & Vacuum Pumps

Stainless Vertical Multi-Stage Pumps

Submersible Pumps Stainless Steel Submersible Pumps are a good choice in Car Wash applications for use with RO spot free water tanks. These pumps are designed to be placed inside tanks for high pressure spot free transfer to bays or automatics. Stainless steel castings and housings for added corrosion resistance. Pumps feature either 2 or 3 wire connections. All units shown are standard with 230 volt, 1-Phase motors (Three phase also available). 1-1/4” FPT discharge.

E-SV™ Stainless Pumps from Goulds Pumps. These Multi-Stage, Vertical Pump and Motor units are ideal for pressure boosting of water supplies, reverse osmosis transfer systems, agricultural irrigation, commercial washing systems, hot & cold water circulation for HVAC applications, boiler feed, etc. Multi-stage design allows for a wide range of flows from 5 to 700 gpm and pressures from 20 to 500 psi.

Non-corrosive cable guard protects motor wires from damage.

CONSTRUCTION FEATURES: 1. One-piece, stainless steel discharge head & NEMA faced mounting ring.

Standard Features:

2. Built-in stainless steel check valve with elastomer ring for positive seal. 3. Sintered lead-free sleeve bearing with polypropylene sand slinger. 4. 304 Stainless Steel Pump shell threaded on both ends for easy attachment to discharge head & mounting ring.

86

D

D

• 304SS Stainless Steel construction • TEFC NEMA Motors (ODP also available) • Silicon Carbide Seal with Viton® Elastomers • Inline ANSI flange inlet x outlet (top/bottom fittings also available) • Simplified design for maximum reliability and fast repair • Impeller O-ring seal produces high pressure and efficiency • Rated to temperatures from -20˚ F. to +250˚ F. • Motors are 60 hz, 3500 rpm and high efficiency. • Optimized hydraulic design results in superior performance, efficiency and low NPSHR.

5. Stainless steel suction screen covers a large round suction inlet. Motor Part No. (TEFC) Voltage Flow Rate Ports Net Ea. GL 3SV16 3hp, 1ph 115/208-230V 16 gpm @ 200 psi *1-1/4” Flange $ 1398.38 GL 3SV163 3hp, 3ph 208-230/460V 16 gpm @ 200 psi *1-1/4” Flange 1385.56 GL 5SV17 5hp, 1ph 208-230V 26 gpm @ 216 psi *1-1/4” Flange 1884.63 GL 5SV173 5hp, 3ph 208-230/460V 26 gpm @ 216 psi *1-1/4” Flange 1680.39 GL 10SV93 7.5hp, 3ph 208-230/460V 40 gpm @ 190 psi 2” FNPT 2304.73 GL 10SV123 10hp, 3ph 208-230/460V 50 gpm @ 234 psi 2” Flange 3126.62 GL 10SV14 15hp, 3ph 208-230/460V 53 gpm @ 260 psi *2” Flange 3143.18 GL 15SV15 25hp, 3ph 208-230/460V 80 gpm @ 375 psi **2” Flange 4663.96 EV R114S 1-1/4” 304SS Threaded Flange, Class 300...................................... 55.75 EV R200S 2” 304SS Thrreaded Flange, Class 300........................................... 67.60 * Pump Flanges are 304 Stainless ANSI Class 300, Raised Face. ** This model has cast iron flanges & base with 304 stainless pump end. — Flange Gaskets Also Available —

1-Ph Motors Wt. Part No. HP Volts * Flow Rate Lbs. Net Ea. FW 4F07S10-305 1 230 7 gpm @ 180 PSI 34 $ 745.00 FW 4F10S15-305 1.5 230 10 gpm @ 185 PSI 43 657.00 FW 4F19S20-301 2.0* 230 13 gpm @ 180 PSI 42 789.00 FW 4F19S30-301 3.0* 230 18 gpm @ 195 PSI 66 1229.00 FW 4F27S30-301 3.0* 230 20 gpm @ 185 PSI 64 1198.00 FW 137224 1 PH Control Box with contactor, 2 HP Units....... 169.00 FW 136800 1 PH Control Box with contactor, 3 HP Units....... 198.50 * 2 Hp & 3 HP Units do not include control box, which must be ordered separately.

Stainless Steel Submersible Pumps

No Outside Shroud Required

D

From Sta-Rite: Stainless Steel Submersible Pumps. Designed for underground tanks or cisterns. Ideal for use with RO Spot Free Water Systems. Shaft, coupling and shell are 300 grade stainless steel construction. Intake and discharge fittings are fiberglass reinforced thermoplastic. All pumps are 1/2 HP and come standard with 10’ power cord. Dimensions are 3-7/8” diameter x 21” long. Motors are 115 or 230 volt, single phase. Designed for direct installation, no outside shrouds needed. 1-1/4” FPT discharge. Weight is 16 lbs.

Call Us For All Your Car Wash & Truck Wash Needs! Visit Our Web Site at

Part No. Flow Rate HP Volts Net Ea.

SA 10DM5121 SA 10DM5221 SA 20DM5121 SA 20DM5221 SA 25DM5121 SA 25DM5221

7-1/2 GPM @ 75 PSI 7-1/2 GPM @ 75 PSI 14 GPM @ 50 PSI 14 GPM @ 50 PSI 20 GPM @ 50 PSI 20 GPM @ 50 PSI

1/2 1/2 1/2 1/2 1/2 1/2

DULTMEIER SALES • OMAHA, NE

115 230 115 230 115 230

http://www.dultmeier.com or E-Mail us at dultmeier@dultmeier.com

$ 296.50 281.00 290.50 290.50 287.00 287.00

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0793


Centrifugal & Jet Pumps

87

Jet Pumps

Stainless Steel Centrifugal Pumps for chemical solutions transfer

Sta-Rite Jet Pumps are an ideal choice for water booster systems in car washes, farms, home, etc. Designed for use in shallow well pumping systems (to 25' lift) or in foam brush, D presoak and tire cleaner applications. All pumps are standard with adjustable pressure switches with shut-off pressures to 70 psi. Available with cast iron, stainless or plastic bodies.

HNC D D

Standard Features “H” Series: Cast Iron Bodies • Noryl Impellers • Stainless steel shaft • Buna Seals • UL & CSA Listed • 1-1/4" Inlet, 1" Outlet.

No. 1ST1F4C4 Pump / Motor Unit

D

† Max. 1ST PUMPS Flow @ Specific Part No. PSI Shown Gravity *Motor Inlet x Outlet Wt. Net Ea. GL 1ST1C4E4 12 gpm @ 30 psi 1.0 1/2hp, 1ph 1-1/4" x 1" 37 lbs. $ 528.89 GL 1ST1C4F4 28 gpm @ 15 psi 1.0 1/2hp, 1ph 1-1/4" x 1" 37 lbs. 537.05 GL 1ST1D1D2 17 gpm @ 36 psi 1.0 3/4hp, 1ph 1-1/4" x 1" 39 lbs. 561.89 GL 1ST1F4C4 20 gpm @ 45 psi 1.0 1-1/2hp, 1ph 1-1/4" x 1" 49 lbs. 699.03 GL 1ST1G4C4 20 gpm @ 45 psi 1.4 2hp, 1ph 1-1/4" x 1" 55 lbs. 770.28 GL 1ST1E4D4 30 gpm @ 30 psi 1.0 1hp, 1ph 1-1/4" x 1" 45 lbs. 616.05 GL 1ST1F4D4 30 gpm @ 30 psi 1.4 1-1/2hp, 1ph 1-1/4" x 1" 49 lbs. 699.03 GL 1ST1G4A4 30 gpm @ 56 psi 1.0 2hp, 1ph 1-1/4" x 1" 53 lbs. 767.10 GL 1ST1G4B4 50 gpm @ 30 psi 1.0 2hp, 1ph 1-1/4" x 1" 53 lbs. 740.07 GL 1ST1H4B4 50 gpm @ 30 psi 1.4 3hp, 1ph 1-1/4" x 1" 58 lbs. 994.19 GL 1ST1H5B4 50 gpm @ 30 psi 1.4 3hp, 3ph 1-1/4" x 1" 52 lbs. 1037.97 * 1-Phase motors are 115/230V on 1 & 1-1/2 HP and 230V on others. 3-Phase motors are 208/230/460V. † Use pumps with 1.4 S.G. for heavy or viscous products such as fertilizers, brines, etc.

PN

Standard Features “P” Series: Plastic Bodies • Fiberglass reinforced thermoplastic body • Polycarbonate Impeller • Stainless shaft & heavy-duty bearings • Buna Seal • 1-1/4" Inlet, 3/4" Outlet.

D

Standard Features “CJ” Series: 304 Stainless Bodies • Noryl Impellers • Buna seals • 1-1/4" MPT Inlet, 1" FPT Outlet.

CJ

*Flow @ Max. Shut-Off Part No. 30 PSI Flow PSI** Body 1-Phase Motors SA HNC 11.6 gpm 15.0 70 Cast Iron 1/2 hp, 115/230 V SA HND 16.5 gpm 21.4 67 Cast Iron 3/4 hp, 115/230 V SA HNE 21.4 gpm 28.5 67 Cast Iron 1 hp, 115/230 V SA PNC 8.5 gpm 8.6 77 Plastic 1/2 hp, 115/230V SA PND 12.0 gpm 12.8 77 Plastic 3/4 hp, 115/230 V SA PNE 18.0 gpm 21.0 67 Plastic 1 hp, 115/230 V SA CJ90E 14.1 gpm 17.8 63 S.S. 1 hp, 115/230V SA CJ90F 14.5 gpm 18.6 80 S.S. 1-1/2 hp, 115/230V * Based on 15' depth to water. ** Shut Off PSI at 5' depth to water.

Series NPE Stainless Steel Centrifugal Pumps from Goulds Pumps. The ideal choice for chemical solutions transfer. Close-coupled pump/motor units or pedestal mount designs in 316SS construction for added corrosion resistance. All standard pumps are fitted with mechanical carbon/ viton seals. Motors are totally enclosed fan cooled, 1-phase or 3-phase. (ODP and explosion-proof also available). Pumps can be mounted in horizontal or vertical position for ease of installation. (1.0 specific gravity is water). Rated to 212° F.

Wt. Net Ea. 47 lbs. $ 318.50 55 lbs. 407.50 60 lbs. 451.50 22 lbs. 294.00 25 lbs. 319.00 27 lbs. 350.00 26 lbs. 381.00 29 lbs. 463.00

2ST & 3ST PUMPS † Max. Flow @ Specific Part No. PSI Shown Gravity *Motor Inlet x Outlet GL 2ST1E4F4 50 gpm @ 18 psi 1.0 1hp, 1ph 1-1/2" x 1-1/4" GL 2ST1H4A4 50 gpm @ 45 psi 1.0 3hp, 1ph 1-1/2" x 1-1/4" GL 2ST1H5A4 50 gpm @ 45 psi 1.0 3hp, 3ph 1-1/2" x 1-1/4" GL 2ST1F4E4 70 gpm @ 20 psi 1.0 1-1/2hp, 1ph 1-1/2" x 1-1/4" GL 2ST1G4C4 70 gpm @ 30 psi 1.0 2hp, 1ph 1-1/2" x 1-1/4" GL 2ST1H4C4 70 gpm @ 30 psi 1.4 3hp, 1ph 1-1/2" x 1-1/4" GL 2ST1H5C4 70 gpm @ 30 psi 1.4 3hp, 3ph 1-1/2" x 1-1/4" GL 2ST1J1G4 70 gpm @ 52 psi 1.0 5hp, 1ph 1-1/2" x 1-1/4" GL 3ST1G4E4 43 gpm @ 30 psi 1.4 2hp, 1ph 2” x 1-1/2” GL 2ST1J5G4 70 gpm @ 52 psi 1.0 5hp, 3ph 1-1/2" x 1-1/2” GL 3ST1H4B4 125 gpm @ 25 psi 1.0 3hp, 1ph 2" x 1-1/2” GL 3ST1H4C4 90 gpm @ 25 psi 1.4 3hp, 1ph 2” x 1-1/2” GL 3ST1H5B4 125 gpm @ 25 psi 1.0 3hp, 3ph 2" x 1-1/2” GL 3ST1H5C4 95 gpm @ 25 psi 1.2 3hp, 3ph 2” x 1-1/2” GL 3ST1J5B4 125 gpm @ 25 psi 1.5 5hp, 3ph 2" x 1-1/2” GL 3ST1J1A4 **130 gpm @ 25 psi 1.4 5hp, 1ph 2” x 1-1/2”

Viton® is a registered trademark of DuPont Performance Elastomers

Visit Our Web-Site:

Wt. 45 lbs. 58 lbs. 52 lbs. 48 lbs. 52 lbs. 58 lbs. 52 lbs. 120 lbs. 55 lbs. 110 lbs. 58 lbs. 58 lbs. 52 lbs. 52 lbs. 110 lbs. 120 lbs.

Net Ea. $ 596.65 997.38 997.38 611.31 752.32 997.38 997.38 996.41 777.85 1301.00 997.00 1047.71 1021.92 1047.42 1363.47 1009.16

* 1-Phase motors are 115/230V on 1 & 1-1/2 HP and 230V on others. 3-Phase motors are 208/230/460V. ** 5 HP, 1 Phase, ODP Motor. † Use pumps with 1.4 S.G. for heavy or viscous products such as fertilizers etc. 1.2 S.G. is adequate for salt brine.

www. dultmeier.com

Jet Pumps

We Now Have Our Catalogs as Well as Parts Schematics Online!

CPJS Style

Shallow Well Jet Pumps from Flint & Walling. Ideal for homes, farms, cottages or wherever water booster service is needed. Specifically designed for applications with suctions lifts to 25 foot depth. Designed for years of trouble-free operation and simple, swift, on-site servicing.

D

Model CPJS Pump Features: • High Tensile Gray Iron Pump Bodies with large cavities for fast, easy priming • Double Ball Bearing, Dual-Voltage Motors • Buna-N Quadraseal for positive seal between pump case and motor bracket • Corrosion & Abrasion Resistant Diffusers • Thermoplastic Celcon Impellers • Carbon & Ceramic Self-adjusting Shaft Seals • All plugs are coated with non-hardening, non-corrosive materials for easy removal if necessary • 1-1/4" FPT Inlet, x 3/4" FPT outlet • Pressure Switch preset at 30-50 psi.

E-Mail us: dultmeier@dultmeier.com

Part No.

*Flow @ 30 PSI HP/Volts

FW CPJ05S 12.7 GPM FW CPJ07S 15.2 GPM

Max. PSI

1/2 (115-230V) 69 3/4 (115-230V) 65

Wt.

Net Ea.

52 lbs. $ 449.00 58 lbs. 529.00

* Based on 15' depth to water. DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0054


Stainless Steel Centrifugal Pumps

88

Pro-Steel Stainless Steel Centrifugal Pumps from Ebara are rated for dependable, continuous duty performance. Built for the most demanding of liquid transfer applications. Available in Straight Centrifugal, Self-Priming and High Pressure 2-Stage models. All pumps are “bulge formed” through a state-of-the-art manufacturing technique that increases pump efficiency, part integrity, reliability and longevity. Standard Features Include: Close-Coupled Design to save space • High Quality Stainless components and ceramic/Viton® seals for added corrosion resistance • Back Pullout Design allows for repairs without removing pumps from system • Mounting Versatility allows for horizontal or vertical service • Centerline Discharge and foot support under casing ensure maximum resistance to misalignment • Available with Flanged or FPT ports • Rated to 212° F. with standard ceramic/Viton® seals. (250° F. seals also available for single stage pumps). • Motors are single or three phase TEFC. (Explosion-proof or ODP also available). NOTE: Flows are based on liquids with 1.0 specific gravity (water). For liquids other than water contact us for hp and chemical compatibility check.

Single Stage Straight Centrifugal - TEFC Motors -

FPT Ports

Part No. Maximum Flow *Motor EA 70-17 17 gpm @ 30 psi 3/4 hp, 1 ph. EA 70-17DE • 17 gpm @ 30 psi 3/4 hp, 1 ph. EA 120-11 25 gpm @ 40 psi 1 hp, 1 ph. EA 120-13 25 gpm @ 40 psi 1 hp, 3 ph. EA 200-11 ** 40 gpm @ 35 psi 1-1/2 hp, 1 ph. EA 200-13 40 gpm @ 35 psi 1-1/2 hp, 3 ph. EA 200-51S ** 90 gpm @ 40 psi 3 hp, 1 ph. EA 200-53 90 gpm @ 40 psi 3 hp, 3 ph. †Flanged

Inlet x Outlet 1-1/4" x 1" FPT 1-1/4" x 1" FPT 1-1/4" x 1" FPT 1-1/4" x 1" FPT 1-1/2" x 1" FPT 1-1/2" x 1" FPT 1-1/2" x 1" FPT 1-1/2" x 1" FPT

Wt. Net Ea. 41 lbs. $ 485.00 36 lbs. 510.00 41 lbs. 505.00 34 lbs. 526.00 40 lbs. 585.00 37 lbs. 560.00 50 lbs. 670.00 47 lbs. 860.00

D

Ports

Part No. Maximum Flow *Motor EA 32-125T1 ** 80 gpm @ 30 psi 3 hp, 1 ph EA 32-125T3 80 gpm @ 30 psi 3 hp, 3 ph EA 40-125B1 •• 200 gpm @ 30 psi 5 hp, 1 ph EA 40-125B3 200 gpm @ 30 psi 5 hp, 3 ph EA 50-160T1 •• 380 gpm @ 30 psi 10 hp, 1 ph EA 50-160T3 380 gpm @ 30 psi 10 hp, 3 ph

Inlet x Outlet Wt. Net Ea. 2" x 1-1/4" Flanges 97 lbs. $ 1375.00 2" x 1-1/4" Flanges 79 lbs. 1055.00 2-1/2" x 1-1/2" Flanges 109 lbs. 1290.00 2-1/2" x 1-1/2" Flanges 99 lbs. 1205.00 2-1/2" x 2" Flanges 185 lbs. 2120.00 2-1/2" x 2" Flanges 165 lbs. 1625.00

230-Volt Only. Open Drip-Proof. 1-phase motors are 115/230 volt, 3-phase are 208/230/460 volt † Designed for 150 lb. ANSI Flanges, (Not included) ** 230-Volt Only. Open Drip-Proof. * ODP Motor with EPDM Seal. Viton® is a registered trademark of DuPont Performance Elastomers •• ODP Motor with VITON® Seal.

D

Two Stage Straight & Self-Priming Centrifugal TEFC Motors • FPT Ports Two Stage Straight

D

Part No. Maximum Flow *Motor Inlet x Outlet EA 2CDX21 26 gpm @ 60 psi 2 hp, 1 ph. 1-1/4" x 1" FPT EA 2CDX23 26 gpm @ 60 psi 2 hp, 3 ph. 1-1/4" x 1" FPT EA 2CDX33 50 gpm @ 60 psi 3 hp, 3 ph. 1-1/4" x 1" FPT EA 2CDX53 65 gpm @ 80 psi 5 hp, 3 ph. 1-1/2" x 1" FPT * 1-phase motors are 230 Volt, 3-phase are 230/460 Volt.

Two Stage Straight

Wt. Net Ea. 40 lbs. $ 675.00 40 lbs. 672.00 55 lbs. 822.00 95 lbs. 1225.00

Self-Priming Part No. Maximum Flow †Motor Inlet x Outlet EA JEU8067T1C 18 gpm @ 25 psi 1 hp, 1 ph. 1-1/4" x 1" FPT EA JEU8067T3C 18 gpm @ 25 psi 1 hp, 3 ph. 1-1/4" x 1" FPT EA JEU1506T1C 18 gpm @ 45 psi 2 hp, 1 ph. 1-1/4" x 1" FPT EA JEU1506T3C 18 gpm @ 45 psi 2 hp, 3 ph. 1-1/4" x 1" FPT † 1-phase motors are 115/230 volt, 3-phase are 208/230/460 volt.

D

Self-Priming Style

Wt. Net Ea. 30 lbs. $ 516.00 32 lbs. 506.00 45 lbs. 566.00 43 lbs. 575.00

Specifically Designed for Car Wash Applications!

Stainless Steel Transfer Pump Stainless Steel Transfer Centrifugal Pump specifically designed for Car Wash and Truck Wash applications. Ideal for use with Presoak, Tire Cleaner, Foam Brush and other common solutions. Housing and impeller are 304SS. Viton® seals are standard. Ports are 1-1/4” inlet x 1” outlet. Rated up to 15 gpm and 50 PSI. Motor is 1 HP, Single or Three phase, 230V TEFC. Maximum temperatures to 250° F. Part No.

HP Phase

SA B82493 1 1 SA B82493MS1 1 3

Flow Rate

Wt.

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

D

Net Ea.

50 lbs. $ 522.00 50 lbs. 513.00

15 GPM @ 50 PSI 15 GPM @ 50 PSI

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0055


Centrifugal • Gear • Sludge Pumps

89

3” Self-Priming “Sludge” Diaphragm Pumps

Bronze Impeller Pump Units

These 3” Diaphragm pumps feature 2-stage, 44 to 1 gear reduction with a large diameter output gear and heavy duty ball bearing construction. Often referred to as Mud Pumps or Sludge Pumps, diaphragm pumps are designed to pump mud, slurry, sewage and thick liquids that have the ability to flow. Industrial Duty. Model 3358-96

• Cast Aluminum Construction for Portability & Durability

D

• Thermoplastic Rubber Diaphragm

These base mounted pumps are ideal for waste oil transfer and other fluids compatible with buna impellers. For high viscosity products use gear pumps on adjacent pages. Pumps used are Sherwood "R" Series bronze pedestal with buna seals and impellers. Motors are 1725 RPM, TEFC with on/off toggle switch and 25' of GFI cord. 10' lift when primed. Self priming to 3 ft., but DO NOT let pump run dry. GPM@15 PSI Part No. * Water HP Wt. DU PM2012 10 GPM 3/4 HP, 110V 42 lbs. DU PM2135 18 GPM 1 HP, 110V 54 lbs. * Flow rates are based on 5' discharge head.

• Primes to 20’ After Initial Prime • Gas Engine, Electric or Air Motor Drive • Wheel Kit with 10” SemiPneumatic Transport Wheels for Portability

D

Model 3355-96

Reclaim Pumps from Sta-Rite. These self-priming pumps are designed for water reclaim and water-tank delivery systems. Bodies are cast iron construction, seals are Viton®. Pumps can lift water up to 25 ft. Maximum pressures to 70 psi if needed. Strainer trap packages are optional to protect pumps from harmful debris. Quick-release cover provides easy access to strainer baskets. Motors are available from 1 hp to 5 hp, 3 phase, 208/230/460 volt. (1 phase available on special order). DH Series

Port Size Suct. x Disch. Max. Part No. HP Engine (NPT) Flow

GR 335B-96 GR 3355-96 GR 3357-96 GR 3358-96 GR 3354-K6 GR 3355-K6

Wt. Lbs.

Net Ea.

5.5 B&S 3” x 3” 88 171 $ 1448.42 1.5 Electric 3” x 3” 58 186 1609.36 5.5 B&S Intek 3” x 3” 88 181 1548.07 5.5 Honda GX 3” x 3” 88 182 1624.35 Pump Kit, Less Engine.... 88 146 1416.23 Pump Kit, Less Motor..... 58 146 1429.11

NOTE: DO NOT USE in explosive atmosphere or for pumping volatile, flammable liquids.

2” Engine Driven “High Solids-Content” Pump • High Chromium Stainless Steel Internal Components Resist Wear from Sea Water or Up to 25% Sand & Debris

D

• Silicon Carbide Mechanical Seal Resists Abrasives & Extends Seal Life

PKG53 / PKG73

D

• Modular Component Design Permits Easy Maintenance & Cleanout; Strainer Included • Maximum Temperature is 180° F.

Net Ea. $ 933.00 1070.00

Reclaim Pump / Motor Units

Note: Inlet flanges or inlet trap strainers must be ordered in addition to the pumps below in order to change pump suction port from flange to pipe thread. One or the other is required but not both.

D

• 1-5/8” Diameter Solids Handling Capability

• Heavy Duty Cast Iron Casing & Adapter Ensures Durability for Severe Service Conditions

Pump with PKG98

Discharge Wt. Part No. Motor * Performance Port Lbs. Net Ea. SA DHE3-50 1 HP / 3 PH 32 GPM @ 30 PSI 1-1/2” 65 $ 447.00 SA DHG3-52 2 HP / 3 PH 44 GPM @ 40 PSI 1-1/2” 113 687.00 SA DHH3-16 3 HP / 3 PH 80 GPM @ 40 PSI 1-1/2” 144 1026.00 SA DHJ3-17 5 HP / 3 PH 140 GPM @ 40 PSI 1-1/2” 184 1091.00 SA PKG53 2” Inlet flange with flapper for (1 HP & 2 HP) 10 47.80 SA PKG73 3” Inlet flange with flapper for (3 HP & 5 HP) 10 71.95 SA PKG51 6” Trap with basket, 2” FPT (for 1 HP & 2 HP) 35 133.50 SA PKG98 8” Trap with basket, 3” FPT (for 3 HP & 5 HP) 48 375.00 * Based on 10’ water lift.

• Handles Up to 1/2” Diameter Solids • Self-Primes to 10 ft. in 1 Minute with Priming Tee! • Honda GX160 5.5HP Engine Part No.

D

Performance Data PSI

10 2 30 40

GPM 152 122 80 22

Maximum Flow 168 GPM

Description

Wt.

GR 316F-95 2” Engine Driven High Solids Pump

85 lbs.

Net Ea.

$ 1057.47

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0659


Circulator Pumps Circulator Pumps

TACO Circulator Pump/Motor Units are designed to circulate heated or chilled solutions in commercial or residential Heating & Air Conditioning Systems as well as Cooling towers, Booster service and Recirculation. Available in either cast iron, bronze or stainless as noted. Flanges can be ordered separately to accommodate a wide variety of plumbing sizes if required.

Series UP Cast Iron Circulator Pumps are specifically designed for Closed Loop, Heating Systems. Ideal for use with Boiler/ Hydronic Systems, Heat Pumps, Radiant Floor Heat and Solar Heating. Motors are 115 volt, single phase.

“00” Series Pump Units Standard Features Include: Unique replaceable cartridge is field serviceable • SelfLubricating bearings • Quiet, efficient operation • High capacity output, compact design • Universal Flange mounts • Direct drive design • Low power consumption • Cast Iron or Stainless casings • Non-Metallic impeller, Ceramic shaft, Carbon bearings • Pressures to 125 PSI • Temperatures to 220° F. • Motors are 115 Volt, 60Hz, Single Phase. UL and CSA listed. 3250 RPM.

90

Features: Pumps are single speed • Working pressures to 145 PSI • Maximum temperatures to 230° F. • Maintenance-Free • Low noise output • Low energy design. Note: Pump units do not include flanges which are shown separately. (Model UP26-99F has higher PSI output than UP26-64F).

D

Part No. Description HP Max. Flow Wt. Net Ea. BL UP15-10F Circulator Pump 1/25 8 GPM 7 lbs. $ 118.00 BL UP26-64F Circulator Pump 1/12 32 GPM 11 lbs. 309.50 BL UP26-99F Circulator Pump 1/6 28 GPM 12 lbs. 325.50 BL 519601 * 3/4” Flange Set................................ 2 lbs. 12.80 BL 519602 * 1” Flange Set................................ 2 lbs. 11.70 BL 519603 1-1/4” Flange Set................................ 2 lbs. 11.70 BL 519604 * 1-1/2” Flange Set................................ 2 lbs. 11.70

D

* These flanges fit UP15 & UP26 Series Only.

“00” Series Pump Units (less flanges) Part No. Construction HP Flow Head Wt. Net Ea. HU 007F5 Cast Iron 1/25 0-20 GPM 0-11 ft. 8 lbs. $ 87.70 HU 007SF5 Stainless 1/25 0-20 GPM 0-11 ft. 8 lbs. 248.50 HU 009F5 Cast Iron 1/8 0-8 GPM 0-34 ft. 9.5 lbs. 212.00 HU 009SF5 Stainless 1/8 0-8 GPM 0-34 ft. 10 lbs. 329.00 HU 0011F4 Cast Iron 1/8 0-28 GPM 0-30 ft. 12 lbs. 223.00 HU 0011SF4 Stainless 1/8 0-28 GPM 0-30 ft. 12.5 lbs. 349.00

“100” Series Pump Units Standard Features Include: Resilient mounted, split phase motors with built-in overload • Onepiece balanced D impeller • Stainless steel shaft • Rugged bronze sleeve bearing • Carbon/ceramic seal assembly • One-piece spring coupling • Factory tested prior to shipment • Easy, low cost servicing, no special tools required • Maximum temperatures to 240° F. intermittent and 200° F. continuous • Maximum pressures to 125 PSI • Motors are 115 Volt, 60Hz, Single phase.

VersaFlo Cast Iron, In-line Circulator Pumps for Stationary Open or Closed Heating and Cooling Systems. Also a good choice for use in Floor Heat or Snow Melt Systems. Features: Motors are 115 or 230 volt, single phase (3 phase also available) • Pumps are multi-speed, wet rotor design • Pressures to 145 PSI • Temperatures to 230° F. • Maintenance-Free motors with thermal protection are standard. Note: Flanges are not included, but can be ordered separately.

D

Part No. BL UPS32-802 BL UPS32-803 BL UPS32-162 BL UPS32-163 BL UPS50-162

Description Circulator Pump Circulator Pump Circulator Pump Circulator Pump Circulator Pump

HP Volts Wt. 1/2 115 38 lbs. 1/2 230 37 lbs. 3/4 115 42 lbs. 3/4 230 44 lbs. 1-1/2 230 67 lbs.

Net Ea. $ 794.00 794.00 1050.00 1050.00 1552.00

“1600” Series Pump Units Standard Features Include: Flows from 10 gpm to 235 gpm with head capacities to 50' • Permanently lubricated bearing cartridge isolates bearing from system temperature • Balanced cast bronze impeller assures long life • Corrosion resistant shaft sleeve • Standard mechanical seals for added flexibility • Resilient mounted motors insure quiet reliable operation • Pressures to 175 PSI and temperatures to 250° F. • Cast Iron Casing and flanges • Alloy steel shaft • Motors are single phase, ODP. (Three phase also available).

Flange Sets for 00 & 100 Series

“100” Series Pump Units (less flanges) D

Part No. Construction HP Flow Head Wt. Net Ea. HU 110C Cast Iron 1/12 0-33 GPM 0-7 ft. 21 lbs. $ 289.50 HU 110B Bronze 1/12 0-33 GPM 0-7 ft. 23 lbs. 440.00 HU 113C Cast Iron 1/8 0-25 GPM 0-17 ft. 27 lbs. 626.00 HU 113B Bronze 1/8 0-25 GPM 0-17 ft. 29 lbs CALL HU 112C Cast Iron 1/3 0-35 GPM 0-22 ft. 28 lbs. 539.00 HU 112B Bronze 1/3 0-35 GPM 0-22 ft. 29 lbs. 851.00 HU 111C Cast Iron 1/8 0-51 GPM 0-12 ft. 26 lbs. 547.00 HU 111B Bronze 1/8 0-51 GPM 0-12 ft. 29 lbs. 761.00

“1600” Series Pump Units (with flanges)

Flange Sets for 00 & 100 Series Pump Units Part No. HU 110-251 HU 110-252 HU 110-253 HU 110-251B HU 110-252B HU 110-253B

Construction 3/4" Cast Iron Flange Set......... 1" Cast Iron Flange Set............ 1-1/4" Cast Iron Flange Set...... 3/4" Bronze Flange Set............ 1" Bronze Flange Set............... 1-1/4" Bronze Flange Set.........

Wt. 2 lbs. 2 lbs. 2 lbs. 3 lbs. 3 lbs. 3 lbs.

DULTMEIER SALES • OMAHA, NE

Part No. FPT Flanges HU 1600C 1-1/2" HU 1610C 1-1/2" HU 1612C 1-1/2" HU 1614C 1-1/2" HU 1634C 2" HU 1636C 2” HU 1638C 2"

Net Ea. $ 9.74 9.74 9.74 28.90 28.05 28.90

(800) 228-9666

www.dultmeier.com

HP Flow Head Wt. Net Ea. 1/4 0-55 GPM 0-20 ft. 59 lbs. $ 676.00 1/3 0-71 GPM 0-23 ft. 62 lbs. 726.00 1/2 0-55 GPM 0-35 ft. 89 lbs. 911.00 3/4 0-70 GPM 0-45 ft. 91 lbs. 1009.00 1 0-170 GPM 0-38 ft. 100 lbs. 1209.00 1-1/2 0-190 GPM 0-40 ft. 125 lbs. 1498.00 2 0-200 GPM 0-50 ft. 153 lbs. 1478.00

• DAVENPORT, IA

(800) 553-6975

E0057


91

Rotary Vane Pumps Procon and Rotoflow

Positive Displacement Rotary Vane Pumps: An excellent choice for handling clean fluids such as tire cleaners, presoak chemicals, spot-free RO water, foam brush solutions, oils, syrups, inks, dyes, acids, etc. Unique design handles liquids with low lubricating characteristics at relatively high pressures. Pumps should be protected from matter larger than 125 microns. Pump Characteristics: Viton® sealing parts for added chemical resistance (1300/1500/1600 & PO300 series) • Replaceable brass or stainless housings • Self-priming • Three-bearing design for pulley or direct drive • Carbon graphite internal vanes, bearings and liner provide no metal to metal contact for long life and quiet operation • Available with relief valves to protect against over pressure (1300/1500/1600 & PO300 series) • Mounting flanges for direct mounting to C-face motors or V-band mounting for “carbonator” motors with “y” frames • Maximum temperature is 150° F. (190° with special seals). Maximum viscosity is 500SSU.

Low Flow Rotary Vane Pumps Rotary Vane pumps are available for mounting to C-face motors or in “CO” models for V-Band clamp mounting to 48Y frame motors. These series of pumps are also standard with built-in relief valves preset a 170 psi. Viton seals are standard. Nominal speed on all units is 1725 rpm. Series 1300: Brass pump body. Flows to 1.70 GPM. This series is standard with a built-in strainer assembly for added protection. Maximum pressure is 200 PSI. Available in “CO” or “C-Face” styles. 3/8" FPT Ports. (Procon Brand). Series 1500: Same specs as 1300 series but does not includes built-in strainer assembly. 3/8" FPT Ports. (Procon Brand). Series PO301/401/501: Brass body. Flows to 2.70 GPM. Standard with relief valve but is less strainer. Maximum pressure is 200 PSI. Standard in “PO” style with V Band. 3/8" FPT Ports. (RotoFlow Brand). Series 1600: Stainless Steel pump body. Flows to 1.70 GPM depending on model specified. Maximum pressure is 200 PSI. Available in either “CO” or “C-Face styles. 3/8” FPT Ports. (Procon Brand). Series PO311/411: Stainless Steel pump body. Flows to 2.30 GPM. Standard with relief valve but is less strainer. Maximum pressure is 200 PSI. Standard in “PO” style. 3/8" FPT Ports. (RotoFlow Brand). Model PO800: (Brass) and PO810 (Stainless) pump bodies. Rated to 4.4 GPM and 200 PSI. Standard in “CO” style with v-band clamps. 1/2" FPT ports. (Rotoflow brand). Maximum Relief

Part No. Body Flow Rate Valve Mount Style Strainer Wt. PB 1304XLV Brass 1.7 gpm yes C-Face Yes 3 lbs. PB PO301FXV Brass 1.7 gpm yes C-Face Yes 3 lbs. PB CO1304XLV Brass 1.7 gpm yes V-Band Yes 3 lbs. PB PO301XV Brass 1.7 gpm yes V-Band Yes 3 lbs. PB 1504XLV Brass 1.7 gpm yes C-Face No 2.5 lbs. PB PO301FV Brass 1.7 gpm yes C-Face No 2.5 lbs. PB CO1504XLV Brass 1.7 gpm yes V-Band No 3 lbs. PB 1604XLV S.S. 1.7 gpm yes C-Face No 3 lbs. PB PO311FV S.S. 1.7 gpm yes C-Face No 3 lbs. PB CO1604XLV S.S. 1.7 gpm yes V-Band No 3 lbs. PB PO311V S.S. 1.8 gpm yes V-Band No 3 lbs. PB PO301V Brass 1.8 gpm yes V-Band No 3 lbs. PB PO401 * Brass 2.3 gpm yes V-Band No 3 lbs. PB PO401V Brass 2.3 gpm yes V-Band No 3 lbs. PB PO411V S.S. 2.3 gpm yes V-Band No 3 lbs. PB PO501 Brass 2.7 gpm yes V-Band No 3 lbs. PB PO501F Brass 2.7 gpm yes C-Face No 3 lbs. PB PO800 Brass 4.3 gpm no V-Band No 4.5 lbs. PB PO801 Brass 4.3 gpm yes V-Band No 4.5 lbs. PB PO810 S.S. 4.3 gpm no V-Band No 4.5 lbs. PB PO811 S.S. 4.3 gpm yes V-Band No 6 lbs. PB 3000130 Coupling Set, Slotted Shaft to 56C Motors.............................. PB 1113 V-Band Clamps for “CO” Pumps as replacement.................... * Buna Seal

C-Face Flange Type

D D

1500 Series (C-Face)

1300 Series (with strainer) PB 3000130 Coupling

"CO" & “PO” V-Band Type

D

Net Ea. D $ 95.50 78.10 95.30 PO401 79.65 86.95 CO1600 Series (V-Band) 68.90 88.55 Carbonator Pump Motors 132.50 126.50 Designed for close-coupled pump applica­tions. Ideal 139.50 for compact pump/motor appli­cations. Slotted 5/8" 124.00 shafts are designed to accept flat-shaft pumps such 67.90 as Procon or Rotoflow brands. D 59.60 68.80 Specifications: 1-Phase, Open Drip-proof • 1725 134.50 RPM • Rated for continuous duty • Automatic overload 119.00 protection • Frames are 48YZ • Rotation can easily be 119.50 changed in the field if required. 119.00 Part No. Size Voltage Amp Rating Wt. Net Ea. 119.50 CE 931 1/3 HP 115 7.0 16 lbs. $ 113.00 195.00 224.00 CE 932 1/2 HP 115/230 8.1/4.2 19 lbs. 133.00 27.05 CE 933 3/4 HP 115/230 6.0 25 lbs. 145.50 1.35

Medium Flow Rotary Vane Pumps These Pumps are designed for use with C-Face motors and do not include built-in relief valves. Primarily used with RO water in spot-free systems. These pumps feature Buna seals (EP & Viton® optional). Maximum viscosity is 500SSU. Maximum 1725 rpm. Series 2500 (Procon) and Model PO800F (RotoFlow) pumps feature brass bodies & stainless steel internal parts. Flows to 4.40 GPM. Maximum pressure is 200 PSI. 1/2" FPT Ports. Shaft size is 7/16". Series 2600 (Procon) and Model PO810F (RotoFlow) pumps feature stainless steel pump bodies and internals. Flows to 4.40 GPM. Maximum pressure is 200 PSI. 1/2" FPT Ports. Shaft size is 7/16" Series 3600 (Procon) and Model PO4100 (RotoFlow) pumps feature stainless steel pump bodies and internals. Flows to 11 GPM. Maximum pressure is 200 PSI. 1" FPT Ports. Shaft size is 5/8". Maximum Relief Part No. Body Flow Rate Valve Mount Style Strainer Wt Net Ea. PO4100 Series (Stainless) PB PO800F Brass 4.3 gpm no C-Face No 4.5 lbs. $ 118.50 (shown with Bell Housing) PB PO801F Brass 4.3 gpm yes C-Face No 4.5 lbs. 120.00 PB 2507A Brass 4.0 gpm no C-Face No 4.5 lbs. 123.50 PB PO810F S.S 4.3 gpm no C-Face No 4.5 lbs. 203.00 PB 2607A S.S 4.0 gpm no C-Face No 5 lbs. 207.50 D PB PO1001F Brass 5.3 gpm no C-Face No 5 lbs. 120.00 PB PO4100 S.S 11.0 gpm no C-Face No 15 lbs. 509.00 PB 3611A S.S 11.0 gpm no C-Face No 15 lbs. 539.00 PB 1048-1C Bell Housing for 2500/2600/PO800/PO810 pumps to 56C motors...... 36.00 PB 3207 Bell Housing for 3600 only pump to C-Face motors............................. 59.55 PB 3300060 Bell Housing for PO4100 with bolts and Key........................................ 71.15 PB 3341-1 Bell Housing & Coupling Set, 3600 Series........................................... 115.00 Note: Other models with different flow rates are available on special order. Viton® is a registered trademark of DuPont Performance Elastomers Note: See coupling section for appropriate drive couplers for above pumps.

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

D

2500 Series (Brass) 2600 Series (Stainless)

D

3600 Series

(800) 553-6975

E0042


Plunger Pumps

92

Plunger Pumps from PumpTec can be used in a wide variety of spraying applications including: Carpet Cleaning, Pest Control, Turf Spraying, Misting and Reverse Osmosis Systems. Available with 12, 120 or 230 volt motors. Sold in pump/motor combinations or as replacement pumps and repair parts. Regulators, repair kits and misting nozzles are also available.

Model 112 Model 112 Pumps feature aluminum bodies with SS/ Acetal valves, stainless plungers and Buna or Viton® seals. Rated to 250 PSI and 140° F. Ports are 1/4” FPT inlet and outlet.

Model 212T Model 212T Pumps feature aluminum bodies with stainless steel plungers and Viton® elastomers. Rated to 200 PSI and 120° F. Ports are 1/4” FPT inlet and outlet. D

112 Series

Part No. Volts PX 212T-170/M20 12V PX 212T-170/M94 12V PX 212T Pump Only

GPM Maximum Amp Part No. Volts Flow PSI Draw Seals Wt. Net Ea. PX 112V-M35 120V .67 200 1.2 Buna 10 lbs. $ 222.50 PX 112T-M35 120V .89 200 1.4 Buna 10 lbs. 219.00 PX 112-075 12V 1.0 200 15 Viton® 10 lbs. 242.00 PX 112T Pump Only 1.4 250 - Viton® 3 lbs. 161.00 PX 112V Pump Only 1.4 250 - Buna 3 lbs. 155.00

GPM Maximum Amp Flow PSI Draw Seals Wt. Net Ea. 2.20 50 16 Viton® 16 lbs. $ 247.50 3.00 30 17 Viton® 10 lbs. 245.00 3.50 85 - Viton® 5 lbs. 169.00

Model 348U Model 348U Pumps feature aluminum bodies with stainless steel plungers and valves. Seals are Viton® or Buna. Rated to 1000 PSI and 140° F. Ports are 3/8” FPT inlet and outlet.

Model 113 Model 113 Pumps feature aluminum bodies with stainless plungers and valves. Seals and o-rings are Buna. Rated to 1000 PSI and 140° F. Ports are 1/4” FPT inlet and outlet.

D

D

113 Series

Part No. PX 113R-M47 PX 113VM-075/M15

GPM Maximum Amp Volts Flow PSI Draw 120V .25 1000 1.5 12V .20 800 15

Seals Buna Buna

Part No. Volts PX 348U-130/M81 120V PX 348-M23 12V PX 348U Pump Only

Wt. Net Ea. 15 lbs. $ 265.00 11 lbs. 286.00

Model 356U Pumps feature aluminum bodies with stainless steel plungers and valves. Seals are Viton® or Buna. Rated to 1200 PSI and 140° F. Ports are 3/8” FPT inlet and outlet.

Model 114 Pumps feature Grilon Plastic bodies with Acetal valves, stainless plungers and Buna or Viton® seals. Rated to 200 PSI and 140° F. Inlet ports are 1/2” hose barb, 3/8” MPT. Outlet ports are 1/4” MPT.

D

REPAIR KITS

Model 205V

Part No. PX 112KITA PX 112KITA-V PX 10034 PX 204KITA PX 348KITA PX 10007 PX 112KITB PX 10018 PX 10004 PX 10014 PX 10020 PX 204KITB PX 10022 PX 212KITB PX 10010 PX 10016

Model 205V Pumps feature aluminum bodies with stainless steel plungers and valves and Buna seals. Rated to 800 PSI and 140° F. Ports are 3/8” FPT inlet and outlet. D

GPM Maximum Amp Flow PSI Draw .90 800 7.2 1.10 500 3.5 1.60 800 -

Seals Wt. Net Ea. Buna 29 lbs. $ 357.00 Buna 30 lbs. 415.50 Buna 5.5 lbs. 181.50

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES • OMAHA, NE

D

GPM Maximum Amp Part No. Volts Flow PSI Draw Seals Wt. Net Ea. PX 356U-200/M64 120V 1.50 1000 11.5 Buna 48 lbs. $ 443.50 PX 356-M26 12V 2.19 300 61 Viton® 45 lbs. 489.00 PX 356-M96 12V 2.50/2.0 250/450 44/66 Viton® 47 lbs. 682.00 PX 356U Pump Only 2.9 1000 - Buna 6.5 lbs. 227.00

GPM Maximum Amp Part No. Volts Flow PSI Draw Seals Wt. Net Ea. PX 114T-M35 120V .89 200 1.4 Buna 10 lbs. $ 182.50 PX 114T-075/M15 12V 1.50 200 15 Viton® 10 lbs. 175.50 PX 114T Pump Only 1.50 200 - Viton® 2.5 lbs. 98.40

Part No. Volts PX 205V-110/M18 120V PX 205V-125/M77 120V PX 205V Pump Only

GPM Maximum Amp Flow PSI Draw Seals Wt. Net Ea. 1.50 1000 11.5 Buna 30 lbs. $ 459.00 2.60 120 28.5 Viton® 28 lbs. 653.00 2.83 1000 - Buna 5 lbs. 225.50

Model 356U

Model 114 114 Series

D

Kit Description Net Ea. Plunger/Seal Kit, 112/114, Buna................... $ 44.90 Plunger/Seal Kit, 112/114 , Viton®................ 46.40 Plunger/Seal Kit, 113, Buna.......................... 81.70 Plunger/Seal Kit, 204/205/207, Buna............ 49.65 Plunger/Seal Kit, 348U, Buna........................ 76.95 Plunger/Seal Kit, 356U, Buna........................ 75.35 P Valve Kit, 112, Buna................................... 24.85 P Valve Kit, 112, Viton®................................. 26.45 M Valve Kit, 112/113/348/356, Buna............. 28.05 U Valve Kit, 114, , Buna................................. 16.85 G Valve Kit, 114, Viton®................................ 18.45 A Valve Kit, 204V, Buna ................................ 44.90 M Valve Kit, 205V/207, Buna......................... 31.25 S Valve Kit, 212, Viton®................................. 26.45 S Valve Kit, 348/356, Buna............................ 24.85 H Valve Kit, 348/356/357, Viton®.................. 26.45

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0053


Sump Pumps

93

Stainless Steel Sump Pumps

Sump Pumps Little Giant Sump Pumps for pumping of dirty water applications where no solids exist. Submersible design with thermal overload protection. Cast Iron housings with Epoxy coating on all but 5MSP & 5ASP models which feature Zinc housings. Polypropylene base and Polycarbonate base. Available in Manual or Automatic versions. Basic sump pump models shown will handle “grey” or clean water. See “E” series pumps for applications where there may be solids in the water to be removed.

Goulds Sump Pumps for dirty water transfer or dewatering. Stainless steel motor housing, thermoplastic impeller and impeller casing for added corrosion resistance. Features: Single phase, 115-volt • Permanently lubricated motors for extended life and continuous operation • Available in manual or automatic versions with float switches • Maximum solids handling capacity is 3/8" • Discharge ports are 1-1/2" FPT • Buna Seals are standard • Maximum temperature is 104˚F. LSP03 Models are 1/3 HP, single phase, 115 volt. Standard with 10' power cords. Rated to 2.8 amps. 6-1/8" Diameter x 9-1/2" High. Weight is 11 lbs. LSP07 Models are 3/4 HP, single phase, 115 volt. Standard with 20' power cords. Rated to 6.7 amps. 6-1/8" Diameter x 11-1/4" High. Weight is 15 lbs.

D

6CIA

D D

6CIA-RFS

D

5MSP

LSP0711F LSP0311AT

D

Part No. Motor * Max. Flow Control Shut-Off Net Ea. GL LSP0311 1/3hp-115v 36 gpm @ 5' Manual 20' $ 149.29 GL LSP0311AT 1/3hp-115v 36 gpm @ 5' Automatic 20' 176.87 GL LSP0711F 3/4hp-115v 57 gpm @ 10' Manual 34' 220.17 GL LSP0711ATF 3/4hp-115v 57 gpm @ 10' Automatic 34' 247.79 * Flow rates will decrease with higher discharge pressure or head.

Model 5MSP: Manual pump with flow rates to 20 gpm, (14 gpm @ 15' height). Shut-off height is 26'. Standard with Viton® seal. Motor is 1/6 hp, 115 volt with 18' power cord. 5 amp draw at startup. Discharge port is 1" FPT. Dimensions: 7-3/4" H x 6-1/16" L x 4-5/16" W. Zinc housing. Weight 9 lbs. Model 5ASP-FS: Same as above but with remote float switch for “on” at 11" and off at 3". Power cord is 10'. Model 6CIM-R: Manual pump with flow rates to 46 gpm, (24 gpm at 10' height). Shut-off height is 17'. Motor is 1/3 hp, 115 volt with 25' power cord. 13 amp draw at startup. Discharge port is 1-1/2" FPT. Dimensions: 7-1/4" H x 9-1/4" L x 7-1/4" W. Weight 18 lbs. Model 6CIA-RFS: Same as above but with remote float switch for “on” at 7-10" and off at 1-4". Standard with 10' power cord.

Cast Iron Sump Pumps Cast Iron Sump Pumps for dewatering, effluent transfer and dirty water. Motors are 1/3 HP, 115 volt, single phase with built-in thermal overload. Discharge port is 1-1/2" FPT. Rated to 104° F. Body is cast iron, impeller and cover are thermoplastic. All models will handle solids to 1/2" diameter. Pump Dimensions (less float): 9-3/4" L x 6-1/2" W x 10-1/2" H.

Model 6CIA: Same as above but with an attached float switch. Dimensions: 6" H x 9-1/2" L x 8-1/2" W. ST31A1

Model 8-CIM: Manual pump with flow rates to 54 gpm, ( 26 gpm @ 15' height). Shut-off height is 23'. Motor is 4/10 hp, 115 volt with 25' power cord. Discharge port is 1-1/2" FPT. Dimensions: 6" H x 9-1/2" L x 8-1/2" W. Weight 19 lbs.

ST31AV

Model 8-CIA: Same as above but with attached float switch for “on” at 7-10" and off at 1-4".

Standard Features: 10' power cord • Seal constructed of carbon/ceramic/buna • Vertical float switch, remote float switch or manual models • Maximum flows to 60 gpm and 26 ft. head • Available in 3 models.

D

Part No.

Motor

GJ 5MSP 1/6hp -115v GJ 5ASP-FS 1/6hp -115v GJ 6CIM-R 1/3hp -115v GJ 6CIA-RFS 1/3hp -115v GJ 6CIA 1/3hp -115v GJ 8-CIM 4/10hp -115v GJ 8-CIA 4/10hp -115v

Max. Flow Auto Switch

20 gpm 20 gpm 46 gpm 46 gpm 46 gpm 54 gpm 54 gpm

No Yes No Yes Yes No Yes

Switch

* Max. Flow

GL ST31M Manual 50 gpm @ 5' GL ST31AV Vertical 50 gpm @ 5' GL ST31A1 Remote 50 gpm @ 5'

NOTE: Check pump compatibility if chemical solutions are to be removed Part No.

D

8-CIA

Shut-Off

26' 26' 26'

Wt.

Net Ea.

29 lbs. $ 142.12 29 lbs. 159.76 29 lbs. 149.64

* Flow rates will decrease with higher head pressure. Wt.

Net Ea.

9 lbs. $ 110.50 9 lbs. 149.00 18 lbs. 137.00 18 lbs. 151.00 18 lbs. 137.00 19 lbs. 205.00 19 lbs. 234.50

SERVICE & REPAIRS Did you know? We can service almost every brand of pump we sell in our catalog. Call us at 1-800-228-9666 (Omaha, NE) for a quote!

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0058


Sump/Effluent Pumps

94

Little Giant Effluent Sump Pumps are designed for pumping dirty water with solids handling capabilities up to 3/4" diameter. Completely submersible design. Applications include • De-watering • Construction sites • Sewer/Septic lines • Fountains/ waterfalls • Elevator Pits, Car Wash Pits and many more. Standard Features include: Cast Iron pump housings with Epoxy coating for added corrosion resistance • Oil-filled motor housings for lifetime lubrication • Thermal overload protection • All motors are single phase, (three available on some models) • All pumps are UL/CSA approved. Check pump components for compatibility if chemical solutions are to be removed.

Features:

Standard Temperature Pumps Model 6E-CIM: Manual pump with flow rates to 50 gpm, (42 gpm @ 10' height). Shut-off height is 22'. Motor is 1/3 hp, 115 volt with 20' power cord. 6 amp draw. Discharge port is 1-1/2" FPT. Handles solids up to 1/2". Seal is Buna. Dimensions: 9-7/8" H x 8-3/4" L x 8-1/2" W. Weight 27 lbs. Model 6E-CIASFS: Same as above but with attached float switch for “on” at 7-10" and off at 2-5" liquid levels. Dimensions: 10-1/4" H x 10-1/2" L x 8-1/2" W. Wt. 28 lbs. Model 8E-CIARFS: Same as above but with remote float switch for “on” at 7-10", “off” at 2-5" liquid level. Weight 29 lbs.

• Cast iron pump housings with protective epoxy coating for corrosion and rust resistance. • Vortex Nylon impeller (except 20E-CIM). • Mechanical seals with (stainless steel spring, Nitrile, Buna or Viton® parts, carbon and ceramic or Ni-resist faces). • Oil-filled (mineral oil) motor housings for lifetime lubrication and rapid heat dissipation. • Thermal overload protection. • UL listed, CSA approved.

Model 9EN-CIM: Manual pump with flow rates to 80 gpm, (60 gpm @ 15' height). Shut-off height is 32'. Motor is 1/2 hp, 115 volt with 20' power cord. Discharge port is 1-1/2" FPT. Handles solids up to 3/4". Seal is Nitrile. Dimensions: 9-1/8" H x 9-1/2" L x 6-3/4" W. Weight 28 lbs.

6E-CIM

Model 9EN-CIARF: Same as above but with 15' cord and a remote float switch for “on” at 9-14", “off” at 2-6" liquid level. Weight 29 lbs.

D

D

Model 14EH-CIM: Manual pump with flow rates to 60 gpm @ 20' or 40 gpm @ 30' height. Shut-off height is 50'. Handles solids up to 3/4". Motor is 1/2 hp, 115 volt with 20' power cord. Discharge port is 2" FPT. Handles solids to 3/4". Seal is carbon/ceramic/Nitrile. Minimum discharge head 20’. Dimensions: 16-1/8" H x 14-1/16" L x 9-7/8" W. Weight 82 lbs.

6E-CIASFS

Model 16EH-CIM: High Head, Manual pump with flow rates to 90 gpm @ 30'. Shut-off height is 81'. Motor is 1 hp, 230 volt with 20' power cord. Discharge port is 2" FPT. Handles solids up to 3/4". Seal is Nitrile. Minimum discharge head 20’. Dimensions: 16-1/8" H x 14-1/16" L x 9-7/8" W. Weight 82 lbs. Model 20E-CIM: High Head, Manual pump with flow rates to 135 gpm @ 20' height. Shut-off height is 110' . Handles solids up to 3/4". Motor is 2 hp, 230 volt with 20' power cord. Discharge port is 2" FPT. Seal is Nitrile. Dimensions: 17-1/2" H x 13" L x 8-1/2" W. Weight 92 lbs. Standard with a brass impeller. Minimum discharge head is 20’.

D

D

High Temperature/Chemcial Resistant Pumps Rated to 200° F.

9EN-CIM

Model HT10E-CIM: Manual pump with Viton® Seal. Rated to flows up to 73 gpm, (20 gpm at 20' height). Shut-off height is 24'. Handles solids up to 3/4". Motor is 1/2 hp, 115 volt with 15' power cord. Discharge port is 1-1/2" FPT. Dimensions: 10-1/4"H x 9-5/8" L x 9-1/8" W. Weight 38 lbs.

14EH-CIM

Model HT10E-CIAFS: Same as above but with a float switch for “on” at 11-15”, “off” at 5-9” liquid level. Part No.

GJ 6E-CIM GJ 6E-CIASFS GJ 9EN-CIM GJ 9EN-CIARF GJ 14EH-CIM GJ 16EH-CIM GJ 20E-CIM GJ HT10E-CIM GJ HT10E-CIAFS

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

Motor

Max. Flow Auto Switch

1/3hp - 115v 50 @ 5' 1/3hp - 115v 50 @ 5' 1/2hp - 115v 80 @ 5' 1/2hp - 115v 80 @ 5' 1/2hp - 115v 60 @ 20' 1hp - 230v 90 @ 30' 2hp - 230v 135 @ 20' 1/2hp - 115v 73 @ 5' 1/2hp - 115v 73 @ 5'

• DAVENPORT, IA

No Yes No Yes No No No No Yes

(800) 553-6975

Net Ea.

$ 157.50 167.00 246.50 279.00 642.00 706.00 916.00 447.50 546.00

E0059


Sump / Submersible Pumps

95

Optima Stainless Steel Sump Pumps are an excellent choice for pumping dirty water, semi-dirty water or slurries. Also a good choice for commercial or industrial seepage and effluent. Not for chemical use. Standard Features Include: 3/8" solids handling capability • Rated for continuous duty applications • 304L stainless with high quality corrosion-resistant material • Can be operated whether fully or partially submerged • Built-in thermal protection with automatic reset, (1-phase only) • ISO 2548 Rating • UL/CSA Water resistant cords • Manual or Automatic shut-off • 13" Float switch with cord on 1/3 HP and 24" on 1/2 and 1 HP models.

Stainless Steel

EPPD 1/3 HP pumps feature double BUNA seals (oil bath mechanical seal bottom; lip seal top) and Noryl impellers EPD 1/2 HP and 1 HP pumps feature mechanical seals with Viton® elastomers for added chemical resistance.

EPPD-3AS1

These models are standard with Stainless impellers. Designed to handle up to 3/8" solids. Available in 1/3 & 1/2 hp, single phase or 1 hp, three phase models. Cords: 20' long on 1/3 hp, 1 hp, 1-1/2 hp and 10' on 1/2 hp. Maximum Temperature: to 120° F. continuous or 140° F. intermittent duty. Ports: 1/3 hp units have 1-1/4" FPT ports, 1/2 hp, 1 hp and 1-1/2 hp have 1-1/2" FPT ports. Part No. *Motor **Max. Flow

EA EPPD-3AS1 1/3hp-1phase+ EA EPPD-3MS1 1/3hp-1phase+ EA EPD-5AS1 1/2hp-1phase EA EPD-5MS1 1/2hp-1phase EA EPD-5MT2 1/2hp-3phase EA EPD-10MT2 1.0hp-3phase EA EPD-15MT2 1.5hp-3phase

Flowrate Shut-Off @ 20’ Head Height Control

45 gpm @ 5' 45 gpm @ 5' 73 gpm @10' 73 gpm @ 10' 73 gpm @ 10' 75 gpm @ 25' 83 gpm @ 25'

14 GPM 14 GPM 49 GPM 49 GPM 49 GPM 74 GPM 85 GPM

26’ 26’ 42’ 42’ 42’ 81’ 85’

Dimensions (Diam. x H)

Wt. Lbs.

Automatic 6-3/8" x 10-1/4" Manual 6-3/8" x 10-1/4" Automatic 8-1/4" x 17-3/16" Manual 8-1/4" x 17-3/16" Manual 8-1/4" x 13-7/8" Manual 8-1/4" x 13-7/8" Manual 8-1/4" x 14-13/16"

11 11 27 27 28 31 31

Net Ea.

$ 205.00 198.50 706.00 695.00 635.00 805.00 850.00

D

* 1-phase motors are 115 volt, 3-phase are 208/230 volt ** Maximum flow rates will decrease with higher discharge pressure or heads. + Standard with Buna Seal.

Dominator Stainless Steel Sewage Pumps. An excellent choice when effluents, sewage and larger solid handling is required. • Oillubricated double mechanical seals with Viton® elastomers • 2" Solids handling capability • Rated for continuous duty • 304 stainless with high quality corrosion-resistant materials • Built-in thermal protection on single phase models • ISO2548 Rating • 25' UL/CSA Water resistant cords • Manual or Automatic shut-off • Operates fully or partially submerged. The ideal choice for pumping Industrial, Agricultural or Commercial waste water with suspended solids up to 2" diameter. Available in 1/2 HP through 2 HP sizes in single or three phase. Standard with 25' cords. Rated to 105° F. continuous or 140° F. intermittent duty. Ports are 2" FPT. Flowrate Shut-off Dimensions Part No.

D

AU64S

*Motor

**Max. Flow

EA AU64S 1/2hp, 115v,1ph EA U64S 1/2hp, 115v,1ph EA AU675S 1hp, 115v,1ph EA U675S 1hp, 115v,1ph EA AU611S 1-1/2hp, 230v,1ph EA U611S 1-1/2hp, 230v,1ph EA U615-1 2hp, 230v,1ph EA U615-3 2hp, 230v,3ph EA U615-4 2hp, 460v,3ph EA XPS5230 2hp, 230v,1ph

† 80 gpm @ 10' † 80 gpm @ 10' 105 gpm @ 5' 105 gpm @ 5' 135 gpm @ 5' 135 gpm @ 5' 140 gpm @5' † 180 gpm @ 10' † 180 gpm @ 10' 173 gpm @ 10’

@15’ Head

Height

45 GPM 45 GPM 52 GPM 52 GPM 82 GPM 82 GPM 108 GPM 160 GPM 160 GPM 155 GPM

20’ 20’ 21’ 21’ 26’ 26’ 33’ 46’ 46’ 55’

Control

(Dia. x H)

Automatic 9" x 21-5/8" Manual 9" x 21-5/8" Automatic 9" x 22-13/16" Manual 9" x 22-13/16" Automatic 9" x 20-1/4" Manual 9" x 20-1/4" Manual 9" x 24" Manual 9" x 24" Manual 9" x 20-1/4" Manual 9” x 24”

*1-phase motors are 115 or 230 volt, 3-phase are 208/230 volt **Maximum flow rates will decrease with higher discharge pressure or heads. † You must run these pumps at 10’ discharge head or higher; shut off head is 20’.

Wt.

Net Ea.

36 lbs. $ 680.00 36 lbs. 665.00 41 lbs. 747.00 41 lbs. 756.00 45 lbs. 819.00 45 lbs. 782.00 52 lbs. 940.00 45 lbs. 868.00 45 lbs. 865.00 52 lbs. 930.00

Viton® is a registered trademark of DuPont Performance Elastomers

Submersible Pumps No. 2P547 Submersible Pumps are designed to pump either clear water or effluent. Can be used in elevator pits, home sumps, loading docks, or in other areas where conventional sump pumps would clog or freeze up due to the accumulation of light debris. Unique vertical-path float switch allows pumps to be mounted in narrow pits (12" minimum width).

12-Volt Submersible Pump “PortaPump” 12-Volt DC Sump Pump from Warren Rupp. This handy dirty water pump can be operated from any 12-volt car or truck battery. Ideal for use when no other power source is available. Rated to a maximum of 43 GPM at 5' discharge or 21 GPM at 20' discharge height. Discharge port is 1-1/2" FPT. 30 Amp draw.

D

Snap-action switch automatically turns pump on and off at preset fluid depths. Maximum fluid temperature 130° F. On at 7-1/2" - off at 3". Features: Nonclogging screenless suction inlet • Nonclogging vortex impeller to pass up to 5/8" solids • Cast Iron housing & top • Impeller & base made of Polypropylene • Mechanical seal with corrosion-resistant and stainless steel hardware, Buna-N and carbon/ceramic parts • 43 GPM at 5' head • 19-1/4 ft. shut-off. 1-1/2" NPT discharge. Housing Impeller Volts Dimensions No. & Top & Base HP @ 60 Hz. Amps RPM Height Width 2P547 Cast-Iron Polypropylene 3/10 115 8.0 1550 9-3/4" 10-1/4" Part No.

Wt.

(800) 228-9666

Model SPA12E

Part No.

Net Ea.

SO SPA12E

GN 2P547 Submersible Pump..... 22 lbs. $ 203.00 DULTMEIER SALES • OMAHA, NE

Standard with 30' cable and clamps. Fits 10" openings. Pump dimensions: 10" Diameter x 19-1/4" H.

www.dultmeier.com

D

Wt.

12-Volt Sump Pump

• DAVENPORT, IA

37 lbs.

(800) 553-6975

Net Ea.

$ 964.00 E0061


Sump Pumps

96

Sewage Sump Pumps Little Giant Sewage Pumps for high volume transfer of liquids with solids up to 2" diameter. Completely submersible design. Ideal for Commercial, Agricultural or Industrial applications where large solids may be present. Standard Features: Oil filled motor housings for lifetime lubrication • Mechanical type seals of Nitrile/ceramic/carbon construction • Thermal overload protection • Cast Iron pump housings with Epoxy coating for added corrosion resistance. All motors are single, phase, (three phase available in some models). All pumps are UL/CSA approved. Model 9S-CIM: Manual pump rated to 110 gpm @ 10' height, (30 gpm @ 15' height). Shut-off height is 20'. Motor is 4/10 HP , 115 volt motor with 20' power cord. Discharge port is 2" FPT. Handles solids to 2". Dimensions: 11-1/2" H x 11-1/2" L x 7" W. Weight 35 lbs.

Specialty Pumps

D

These pumps are ideal for light volume transferring or recirculating of chemical solutions. Specifically engineered for highly specialized applications. Submersible and Nonsubmersible models.

NK1

Model NK1 Submersible pump designed for use in mild acids, alkalies and hard water applications. Perfect choice for automatic soap tank applications. Features: Glass-filled, corrosion resistant, nylon housing • Viton® seal • 1/4" MPT discharge • 6' power cord • Hermetically sealed and filled with special oil for lifetime lubrication • Thermally protected. Dimensions are 4-9/16" x 4-1/8".

D

Model 9S-CIARFS: Same as above but with remote automatic float switch for “on” at 9-14", off at 2-5". 9S-CIM

Model 10S-CIM: Manual pump rated to 120 gpm @ 5' height, (70 gpm @ 15' height). Shut-off height is 25'. Motor is 1/2 HP, 115 volt with 20' power cord. 9.5 amp draw. Discharge port is 2" FPT. Handles solids to 2". Dimensions: 11-1/2" H x 11-1/2" L x 7" W. Weight 36 lbs. Model 10S-CIARFS: Same as above but with remote automatic float switch for “on” at 9-14", off at 2-6" liquid level. Model 14S-CIM: Manual pump rated to 100 gpm @ 10' height. Shut-off is 25'. Motor is 1/2 HP, 115 volt with 20' power cord. Discharge port is 3" FPT. Handles solids to 2". Standard with cast iron impeller. Dimensions: 17-3/16" H x 14-1/16" L x 9-7/8" W. Weight 80 lbs. Model 16S-CIM: Manual pump rated to 160 gpm @ 10' height. Shut-off is 35'. Motor is 1 HP, 230 volt with 20' power cord. Discharge port is 3" FPT. Handles solids to 2". Standard with cast iron impeller. Dimensions: 17-3/16" H x 14-1/16" L x 9-7/8" W. Weight 88 lbs. Model 20S-CIM: Manual pump rated to 205 gpm @ 10' height. Shut-off is 75'. Motor is 2 HP-1 PH, 230 volt with 20' power cord. Discharge port is 3" FPT. Handles solids to 2". Standard with brass impeller. Dimensions: 19-1/8" H x 12-7/8" H x 7-5/8" W. Weight 96 lbs.

Model 2E-NDVR: Non-Submersible pump for use with weak acids, chemicals, cleaning solvents, anti-freeze, potable fluids (pH of 6-7). Features: Nylon front with 3/8" FPT inlet, 1/4" MPT outlet • Stainless steel plate and motor shaft • Viton seals • 6' power cord • Thermally protected. Dimensions are 4-1/2" H x 5-1/2" L x 3-1/2" W. Part No.

*Flow Rate

HP

Voltage

Wt.

Net Ea.

GJ NK1 210 GPH 1/150 115 Volt 3.4 lbs. $ 79.40 GJ 2E-NDVR 300 GPH 1/40 115 Volt 5.4 lbs. 129.00 *Flow rates are based on 1' discharge height.

Magnetic-Drive Chemical Solution Pumps Medium Flow - Low Pressure LITTLE GIANT Magnetic-Drive Solution Pumps: Ideal for recirculating or transferring corrosive solutions. Compatible with some acids, alkalis, plating solutions or salt solutions. Rated up to 200 degrees F, 100 SSU viscosity and 1.1 specific gravity. (Pumps are for low pressure use). Leak-proof, seal-less magnetic drive eliminates friction loss, wear, leakage, and contamination. Motors are open, fan cooled. Single phase, 115 Volt is standard, (230V optional). Inlet ports are 1/2" FPT or 3/4" FPT. Outlet ports are 1/2" MPT. All pumps shown are UR & CSAC listed.

14S-CIM

Models 2MD and 3MD are designed to handle mildly corrosive solutions. D

Models 2MDSC and 3MDSC are designed for semi-corrosive solutions. Pump heads and impellers on these units are glass-filled polypropylene. Nitrile O-ring is standard. Designed for intermittent duty.

D

Models 2MDHC and 3MDHC are designed to handle highly corrosive solutions. Standard with self-lubricating carbon impeller bushing and Viton O-ring. Pumping head, impeller and encapsulated magnet are of Ryton construction. These pumps have run/dry capabilities to 8 hours. 10S-CIARFS Model 2MDHC

D D

Check pump components for compatibility if chemical solutions are to be removed. Model 2MD

Part No Motor

GJ 9S-CIM 4/10hp-115v GJ 9S-CIARFS 4/10hp-115v GJ 10S-CIM 1/2hp-115v GJ 10S-CIARFS 1/2hp-115v GJ 14S-CIM 1/2hp-115v GJ 16S-CIM 1hp-230v GJ 20S-CIM 2hp-230v

Maximum Automatic Flow Switch

110 gpm @ 5’ 110 gpm @ 5’ 120 gpm @ 5’ 120 gpm @ 5’ 100 gpm @ 10’ 160 gpm @ 10’ 205 gpm @ 10’

No Yes No Yes No No No

Net Ea

$ 271.50 293.00 315.00 335.00 598.00 749.00 954.00

(800) 228-9666

**Solution Use

GJ 2MD GJ 3MD GJ 2MDSC GJ 3MDSC GJ 2MDHC GJ 3MDHC

Mildly Corrosive Mildly Corrosive Semi-Corrosive Semi-Corrosive Highly Corrosive Highly Corrosive

HP GPM* Temperature Wt.

1/30 1/20 1/25 1/12 1/30 1/12

6.85 8.20 6.85 11.0 8.50 11.0

150° F. 150° F. 150° F. 150° F. 200° F. 200° F.

Net Ea.

4 lbs. $ 140.50 7 lbs. 171.50 7 lbs. 163.00 8 lbs. 185.00 7 lbs. 200.50 8 lbs. 244.00

* Based on 6' discharge head. Flows will decrease if higher head is required. **Please check compatibility of solutions to be pumped when ordering.

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES • OMAHA, NE

Part No.

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0060


Sump Pumps

97

Specifically designed for Dewatering, Water Transfer, Sewage Systems or for any use where waste or drainage with up to 3" solids must be disposed of. Mechanical shaft seals with Buna elastomers are standard. Rated to 104° F. continuous or 140° F. intermittent duty. Pump casings are thermoplastic, stainless or cast iron as noted.

1DW Series - 1-1/2" 1DW Stainless Dewatering Pumps for dirty water transfer. Handles solids up to 3/8". Impeller, shaft and casing are 304SS. Diffuser Plate is 304SS with a Polyurethane coating for added abrasion resistance. Manual design is standard but float switches can be ordered separately if required. Motors are 1 phase, 60Hz. 1/2 HP units are 115 volt. 3/4 HP and 1 HP are 230 volt only. Ports are 1-1/2" FPT. Silicon/Carbide mechanical seal with Buna elastomers is standard. Rated for continuous duty up to 120° F. Power cord is 20' long. Part No.

Motor

GL 1DW51COEA GL 1DW51D1EA GL 1DW51E1EA

1/2 hp 3/4 hp 1 hp

Flow Rate Shut-off Ht. Wt.

70 gpm @ 10' 85 gpm @ 10' 93 gpm @ 10'

Net Ea

D

29 lbs. $ 520.73 32 lbs. 585.36 38 lbs. 623.54

36' 44' 52'

1DW Series

WW Series - 2" WW Series Pumps feature Thermoplastic casing, impeller and base. Motor housing is cast iron. Motors are 1/2 HP, 1 phase, 115 volt and are available with or without float switches. Power cord is 10' long. Handles solids up to 2" diameter. Outlet fitting is 2" FPT. Part No.

GL WW0511 GL WW0511A

Motor

Flow Rate

Shut-off Ht. Wt.

1/2 hp 63 gpm @ 10' * 1/2 hp 63 gpm @ 10'

WW Series

Net Ea

D

22 lbs. $ 322.31 23 lbs. 360.24

18' 18'

* Standard with float switch for automatic shutoff.

Stainless Sewage Pumps - 1-1/2" & 2" 1DV & 2DV Series pumps feature 304SS Casing, impeller and shaft. All models are manual shut-off but float switches are available as an add-on. Power cords are 20' long. 1DV Models are 1/2 HP, 1-Phase, 115 volt. Will handle solids up to 1-3/8" diameter. Outlet is 1-1/2" FPT. 2DV Models are 3/4 HP and 1 HP, 1-Phase, 230 volt. Will handle solids up to 2” diameter. Outlet is 2” FP Part No.

Motor

GL 1DV51COVA GL 2DV51D1VA GL 2DV51E1VA

1/2 hp 50 gpm @ 10' 3/4 hp 75 gpm @ 10' 1 hp 110 gpm @ 10'

Flow Rate

Shut-off Ht.

26' 24' 33'

Wt.

Net Ea

22 lbs. $ 595.23 30 lbs. 652.73 34 lbs. 696.29

D

DV Series

WSO Series - 2" WSO Series pumps feature Cast iron casing and impeller, Silicon Carbide seal and stainless steel shaft. All models are manual shutoff but float switches are available as an add-on. Power cords are 20' length. Ports are 2" FPT. All pumps in this series will handle solids up to 2" diameter. 1/3 HP and 1/2 HP are 1-Phase, 115 volt. 3/4 HP & 1 HP motors are 1-Phase, 230 volt. D

Part No.

Motor

Flow Rate

Shut-off

GL WS0311B GL WS0511B GL WS0712B GL WS1012B

1/3 hp 1/2 hp 3/4 hp 1 hp

80 gpm @ 10' 120 gpm @ 10' 150 gpm @ 10' 180 gpm @ 10'

19' 25' 30' 38'

Wt.

Net Ea

70 lbs. $ 418.63 70 lbs. 521.06 77 lbs. 715.59 86 lbs. 784.50

WSO Series

WS Series - 3" & 4” WS15/20/30/50 Series pumps feature Cast Iron casing and impeller, Stainless steel shaft and fasteners, Silicon/Carbide seal and Buna elastomers. All models are manual shutoff. Handles solids up to 3" diameter. Power cords are 20' long. Ports are 3" flange for 150 lb. ANSI standard. Motors shown are 230 volt. (208 or 460 volt also available). Shut-off Wt. Part No. Motor Flow Rate Height Lbs. Net Ea. GL WS1512D3 1.5hp-1ph 300 gpm @ 10' 38' 188 $ 1910.73 GL WS1532D3 1.5hp-3ph 300 gpm @ 10' 38' 185 1948.16 GL WS2012D3 2hp-1ph 350 gpm @ 10' 45' 193 2126.43 GL WS2032D3 2hp-3ph 350 gpm @ 10' 45' 190 2054.86 GL WS3012D3 3hp-1ph 400 gpm @ 15' 54' 205 2573.73 GL WS3032D3 3hp-3ph 400 gpm @ 15' 54' 195 2300.97 GL WS5012D3 5hp-1ph 450 gpm @15' 65' 210 2795.52 GL WS5032D3 5hp-3ph 450 gpm @15' 65' 200 2405.65 GL WS5012D4 * 5hp-1ph 550 gpm @18’ 51’ 213 2872.51 GL WS5032D4 * 5hp-3ph 550 gpm @18’ 51’ 210 2429.67 * 4” Models DULTMEIER SALES • OMAHA, NE

(800) 228-9666

D

WS Series

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0062


Water System Accessories Precharged Water Tanks

Liquid Level Switches

VT120

VT85

98

Level Switches are designed to control liquid levels and open or close circuits for rising or falling levels of fluids. Power cords or lead wires are included and are shown with each model. All models can be used with relays if higher amp draws are required.

VT60

VT20

2A555

2A554

D D D

D D

CFS2

D

VT36 HT14

LT2 & LT5

RFSN-9 & 10

Pre-charged water tanks for use with water systems or holding tanks. Designed to give constant pump pressure. Reduces the amount of pumping cycles required which helps extend pump life. Available in Vertical or Horizontal models. Drawn steel construction with baked-on, polyester, painted finish. Standard with PVC diaphragms. Maximum working pressure is 100 PSI. Precharge pressure is 40 psi. FDA approved. Maximum temperature is 120° F. All units are standard with air valves. Models LT2 / LT5 are small compact units that are standard with a 3/4" MNPT connection on the bottom. Can be plumbed directly onto the pump. LT5 has 1/4” MPT inlet. Model HT14 is a Horizontal model that includes a pump mounting bracket. Capacity is 14 gallons. HT14V is a Vertical Style. 1" FNPT Connection. Models VT20 & VT36 are vertical models. Connections are 1" FNPT. Models VT60, VT85 & VT120 are vertical models & have 1-1/4" connection. Tank Drawdown DIMENSIONS Part No. Capacity @ 30 PSI Diameter x Height SR LT2 2.0 gallon .7 GPM 8" x 12" SR LT5 5.0 gallon 1.5 GPM 11" x 15" SR HT14 * 14 gallon 4.3 GPM 21"x16" SR VT20 19 gallon 5.8 GPM 16" x 27-1/2" SR VT36 33 gallon 11.3 GPM 16” x 43” SR VT44 44 gallon 15.0 GPM 53” x 36” SR VT60 62 gallon 18.3 GPM 24" x 39-1/2" SR VT85 81 gallon 27.0 GPM 53" x 62" SR VT120 120 gallon 40.0 GPM 66" x 60" * HT14 is a horizontal style tank with mounting plate.

Wt. Net Ea. 5 lbs. $ 53.65 10 lbs. 55.95 28 lbs. 119.00 40 lbs. 123.50 49 lbs. 189.50 67 lbs. 293.00 112 lbs. 359.00 99 lbs. 369.50 153 lbs. 619.00

Pressure Switches for Water Systems

D

Part No. Net Ea. GO 69ES1 $ 41.55 GO 69ES2 48.95

Pressure Switches for the most demanding water systems. Suitable for direct use on all types of pumps up to 5 HP or for use in the control circuit of a magnetic motor starter. Adjustable pressure differential settings. Replaceable contact cartridge. Nema 1 rating. UL Listed. CSA certified. Inlet port is 1/4” FPT.

Horsepower Min Close Max Open Differential 1-Phase 3-Phase Factory GO-NO. Cut In Cut Out Range 115V 230-Volt 230-Volt Setting 69ES1 10 80 15-25 1-1/2 2 3 30-50 69ES2 10 80 15-25 2 3 5 30-50

D

2XC13

D

Model 2XC13 is designed for horizontal mounting. Polypropylene construction. 1/2” MPT dual threads allow for mounting inside or outside of vessel. Overall length is 3-1/2”. Rated to 176° F. and 116 PSI. 12” lead wires. Rated to .08 amps @ 240 volt (Can also be used on 110 volt and 208 volt). U.L. listed. Model 2A554 is designed for vertical mounting. Polypropylene construction. 1/8” MPT thread. Length is 2-1/8” high x 1” wide. Rated to 220° F. and 110 PSI. 24” lead wires. Rated to .14 amps at 220 volt but can also be used on 110 volt. U.L. listed. Model 2A555 is designed for vertical mounting. 316SS construction. 1/8” MPT thread. Overall length is 2” high x 1” wide. Rated to 300° F. and 450 PSI. 18” lead wires. Rated to 1 amp at 200 volt. (Can be used on 110 volt). U.L. listed. Model CFS2 is a mechanically actuated floating switch. Polypropylene construction with 20’ PVC cord. Rated to 16 amp at 120 volt or 12 amp at 240 volt. Dimensions are 6-1/4” x 3-3/16”. Single-pull, double-throw design can be used for “on-rise” or “on-fall” applications. UL/CSA listed. Model RFSN-9 & RFSN-10 are switches designed for use with sump pumps. These are remote mount, floating switches. Designed for “on-rise” only. Rated to 13 amps at 115 volt and 140° F. Float diameter is 3”. RFSN-9 is standard with a 15’ cord. RSFN-10 has a 20’ cord. Part-No. Construction AR 2XC13 Poly AR 2A554 Poly AR 2A555 316SS DR CFS2 Poly GJ RFSN-9 Poly GJ RFSN-10 Poly

Wires/Cord 12” Lead Wires 24” Lead Wires 18” Lead Wires 20’ Cord 15’ Cord 20’ Cord

Net Ea. $ 18.95 18.45 45.95 20.95 42.10 53.45

Call Us For All Your WATER SYSTEM Needs! OMAHA, NEBRASKA

DAVENPORT, IOWA

1-800-228-9666

1-800-553-6975

FAX: 1-402-333-5546

FAX: 1-563-386-5448

http://www.dultmeier.com

TANK SELECTION: Determine the Flow Rate of Your Pump in Gallons Per Hour • Choose Your Pressure Switch Setting • Select the Tank from the Chart Below with Drawdown at Your Chosen Switch Setting that is Equal to or Above Your Pump GPH. Pump GPH 240 300 360 420 480 540 600 720 840 960 1080 1200 1320 1500 1800 2100 2400 2700 3000 3600 4800 6000 7200 Tank Drawdown* 4 5 6 7 8 9 10 13 17 20 25 30 36 44 60 70 80 90 100 120 160 200 240 Gallons * The amount of usable water discharged between pump cycles of an automatic water system. DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0067


Valves • Vacuum Breakers

99

Vacuum Breakers

RPZ Valves Reduced Pressure Zone Backflow Preventers

For Back-Siphon Protection

RPZ Backflow Preventers for prevention of back-siphonage and backpressure of contaminated water into safe water supplies in accordance with national plumbing codes and water utility authority requirements.

Anti-Siphon Vacuum Breakers designed to prevent back-siphonage of contaminated water into safe water supply.

Required by many states for use in fertilizer, chemical and industrial plants to protect safe water supplies from chemical contamination. Designed for high hazard cross connections in plumbing systems or for containment at the service line entrance.

B800: Hose Connection Vacuum Breakers. Inlet is 3/4" Female Garden Hose Thread. Outlet is 3/4" Male Garden Hose Thread. Maximum pressure is 125 PSI. Maximum temperature is 180° F. Note: For frost-free hydrants use NF8 listed below.

Model B800: Basic Vacuum Breaker. Designed to be removed and reused if required.

D

B800

D

Model NF8: Especially made for wall and yard hydrants. Permits manual draining for freezing conditions. Has shearing head set screw which locks it to the hydrant to prevent tampering.

D

NF8 STANDARDS Tested and certified under the following standards: ASSE # 1013. AWWA # C506. FCCCHR of USC manual, section 10. IAPMO listed.

Vacuum Breakers with FPT ports for hot or cold water. For cross connections not subject to continuous pressure. Available in 1/4" through 2". Maximum temperature is 180° F. @ 125 PSI.

Series 009QT: Standard RPZ Backflow Preventer. Sizes from 3/4" through 2". SupD ply pressures to 175 No. 009QT PSI. Water temperatures to 180° F. Features: (2) in-line, independent check valves with an intermediate relief valve • Ball type test cocks • (2) Quarter-turn, full port, resilient seated bronze ball valve shut-offs. • Modular construction • Renewable seats • Available with or without bronze strainer.

D

Part No. Inlet Port Outlet Port Net Ea.

WS B800 WS NF8 HR 506300 WS 288A-3/8 WS B3599 WS B3500 WS B3501 WS B3503 WS B3504

Series 909QT: This valve incorporates the (“airin/water-out”) principle which substantially improves the relief valve discharge performance. (The emergency conditions of D combined back-siphonNo. 909QTS age and back-pressure with both checks fouled can defeat the effectiveness of a standard RPZ backflow preventers). Note: Sizes from 3/4" through 2". Supply pressures to 175 PSI. Water temperatures to 140° F. Features: (2) Quarter-turn, full-port, resilient seated bronze ball valve shut-offs • Ball valve test cocks • Bronze body construction • Modular design, replaceable seats • Tight-seating rubber check valve and relief valve assemblies • Stainless steel relief valve seats, shafts and flange bolts • Available with or without bronze strainer. Part No. FPT Size Strainer Wt. Net Ea. WS 009QT-3/4 3/4" No 11 lbs. $ 263.00 WS 009QTS-3/4 3/4" Yes 13 lbs. 245.00 WS 009QT-1 1" No 12 lbs. 268.00 WS 009QTS-1 1" Yes 15 lbs. 246.50 WS 009QT-1-1/2 1-1/2" No 29 lbs. 473.00 WS 009QTS-1-1/2 1-1/2" Yes 33 lbs. 513.00 WS 009QT-2 2" No 33 lbs. 573.00 WS 009QTS-2 2" Yes 39 lbs. 545.00 WS 909QT-3/4 3/4" No 16 lbs. 455.50 WS 909QTS-3/4 3/4" Yes 18 lbs. 709.00 WS 909QT-1 1" No 17 lbs. 499.00 WS 909QTS-1 1" Yes 20 lbs. 784.00 WS 909M1QT-1-1/2 1-1/2" No 43 lbs. 924.00 WS 909M1QTS1-1/2 1-1/2" Yes 45 lbs. 1298.00 WS 909M1QTS-2 2" Yes 53 lbs. 1469.00 WS 777-1 * 1" 20 Mesh Strainer..... 35.95 WS 777-1-1/2 * 1-1/2" 20 Mesh Strainer..... 71.95 WS 777S-2 * 2" 20 Mesh Strainer..... 109.00 *Permits interchange from QT to QTS Style. DULTMEIER SALES

OMAHA, NE (800)

228-9666

3/4" FGHT 3/4" FGHT 1/4" FPT 3/8" FPT 1/2" FPT 3/4" FPT 1" FPT 1-1/2" FPT 2"

3/4" MGHT 3/4" MGHT 1/4" FPT 3/8" FPT 1/2" FPT 3/4" FPT 1" FPT 1-1/2" FPT 2" FPT

Note: Not for Continuous Pressure Conditions

Hot Water Tempering Valves

No. 70AT

D

Tempering valves for mixing cold and hot water. For automatic storage water heaters these valves will increase draw capacity. Adjusting dial for “finger-tip” temperature control. B r a s s o r b r o n ze construction with stainless steel springs. Maximum temperature is 210° F. Maximum pressure is 150 PSI.

Temperature Part No. Connections Range

WS 70AT-1/2 WS 70AT-3/4 WS L70AT-1/2 WS L70AT-3/4 WS L1170-3/4 WS MMV-UT

$ 6.95 37.50 35.85 49.30 29.75 32.95 42.85 108.00 169.00

DAVENPORT, IA (800)

553-6975

1/2" FPT 3/4" FPT 1/2" FPT 3/4" FPT 3/4” FPT 3/4" MPT

D

No. L1170-3/4

Net Ea.

120° - 160° F. $ 116.00 120° - 160° F. 141.00 100° - 130° F. 135.00 100° - 130° F. 168.00 60° - 120° F. 222.50 80° - 120° F. 121.00

www.dultmeier.com

E0066


Low Pressure Regulators

Inlet Pressure Regulators For Water

Pressure Reducing Valves Pressure Reducing Valves from Danfoss/Flomatic. Regulates high incoming line pressures to lower constant pressures regardless of water flow. Ideal for pumps and plumbing systems. Bronze construction. Factory set at 50 PSI but adjustable from 15 to 150 PSI. Rated to 400 PSI inlet pressure. Rated to 180° F. Ports are solid MPT x FPT union. Part No.

WS C150199E WS C150100E WS C150101E

B

A

D

C D

Ports

Wt.

1/2” 3/4” 1”

3 lbs. 3 lbs. 6 lbs.

E

Net Ea.

$ 71.80 81.90 91.75

4HC375 REGULATOR Features: (4) PORT Non- relieving Regulator for 3/8" pipe size. (2) 3/8" FPT ports and (2) 1/4" FPT gauge ports. Adjustable pres­sure range is 5 to 50 PSI. Maximum incoming pressure up to 400 PSI. Maximum tempera­ture to 200° F. 4HC500 REGULATOR Features: The same as 4HC375 Except for 1/2" pipe size. (2)1/2" FPT ports and (2) 1/4" gauge ports.

Pipe Size A B 3/8" & 1/2" 5-1/2" 4-3/8" Part No.

Watts Bronze Pressure Reducing Valves. Rated to a maximum of 300 psi incoming pressure. Designed to reduce incoming water pressures to a range between 25 & 75 psi (preset @ 50 psi). Standard with built-in bypass. Maximum temperature is 160° F. Ports are FPT union inlet x FPT outlet. Note: Valve has a 1/8" gauge port plug. Optional gauge not included.

WS 25AUB-3/4 WS 25AUB-1 WS 25AUB-1-1/4 WS 25AUB-1-1/2 WS 25AUB-2

Size

Flow Rate

3/4" 1" 1-1/4" 1-1/2" 2"

25 gpm 38 gpm 52 gpm 60 gpm 85 gpm

Wt.

3/8” FPT * 7-1/2 1/2” FPT * 7-1/2 Repair Kit for Both .........

Net Ea.

$ 80.95 80.95 30.40

* Based on 100 PSI incoming and 20 PSI Discharge Pressure.

Inlet Pressure Regulator WATTS 263A Water Regulator valves are adjustable from 3 to 50 PSI Outlet pressure.Valves are Pre-Set at the factory at 15 PSI. Capacity is from 2 to 4 GPM. Inlet ports are 3/8” FPT. Gauge port is 1/4" FPT. Body is Brass.

Net Ea.

2.8 lbs. $ 169.00 5.5 lbs. 221.50 10 lbs. 375.00 10 lbs. 499.00 22 lbs. 729.00

Part No.

Net Ea.

WS 263A-3/8B Brass Regulator.................... $ 97.65 WS 26ARK Repair Kit ............................. 24.30

Pressure Regulator/Injector

Air Separators

Model PR1000A Ideally suited for use as an inlet regulator and chemical injector in one!! Simply attach this unit to your water supply and run a line to the pump inlet. This regulator will control the pump suction pressure to approximately 5" vacuum acting as a constant regulation of incoming water.

C D E 1-1/8" 2-5/8" 3-3/16"

Pipe Flow Size GPM

GE 4HC-375B GE 4HC-500B GE HC-B

D

Part No.

D

“HC” Series “GENERANT” HIGH CAPACITY PRESSURE REGULATORS: Ideal for regulating incoming water pressure. Protect your pumps and injectors from high incoming pressures. Constructed of forged brass and other high grade non-rusting materials. Long trouble-free service is assured. Fully balanced for uniform regulation at high volumes. Weight is 3 lbs. (For Air Service — see Air Regulators.)

Water Pressure Reducing Valves

D

100

Air Separators for the removal of air in closedloop hydronic heating systems. Forged brass construction. Designed to withstand glycol, petroleum and methanol-based antifreeze products. All models feature automatic and manual air vents. Available with threaded FPT or solder ports as noted. 1/2” FPT bottom port for expansion tank mounting. Rated to 150 PSI and 240° F.

D

Can also be used to introduce Soaps or Waxes directly into the system through the regulator body. Chemical metering is more stable than almost any other type of injection device. Eliminates the need for float tanks or separate chemical injectors. Flow capacity is 6 GPM. Maximum temperature is 160° F. Part No. Gun Style GPM Inlet & Outlet Injector Port Net Ea. FL PR1000A Weep 6 1/2" FPT (Two) 1/4" FPT $ 74.95 FL PR1000A-1 Non-Weep 6 1/2" FPT (Two) 1/4" FPT 75.60 FL PR1000A-RK Repair Kit for Weep Regulator.............................. 31.25 FL PR1000A1-RK1 Repair Kit for Non Weep Regulator...................... 31.00

Part No.

WS ASMB75 WS ASMB100 WS ASMB125 WS ASMBS75 WS ASMBS100 WS ASMBS125

Port

3/4" FPT 1” FPT 1-1/4” FPT 3/4” Sweat 1” Sweat 1-1/4” Sweat

Wt.

2.5 lbs. 2.65 lbs. 2.80 lbs. 2.50 lbs. 2.65 lbs. 2.80 lbs.

D

Net Ea.

$ 103.50 122.00 130.00 100.00 117.00 125.50

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0068


Unloader Valves

101

– Pressure Actuated – Unloader Valves

Unloader Valves Pressure Sensitive

Pressure Sensitive

D

D

ST291 ST261

ST261-S

Pressure Activated Unloader Valves from Suttner. Can be used for single or multiple gun applications. Flow-through design for ease of installation. Valves are shown with or without pressure switches rated to 5 amps at 120 volts or 3 amps at 250 volts. Inlet and outlet are 3/8” FPT. Bypass is 1/4” FPT. Temperatures to 175° F. All valves shown are rated to 8 GPM. Brass bodies with Viton® seals. Part No.

Pressure Range

Switch

Net Ea.

NP ST261 NP ST261L NP ST280 NP ST291 NP ST261-S NP ST291-S

500 - 3600 PSI 200 - 1000 PSI 500 - 4000 PSI 850 - 5070 PSI 500 - 3600 PSI 850 - 5070 PSI

No No No No Yes Yes

$ 38.60 38.60 49.85 124.50 68.90 155.00

D

D

D

VRT100-330

Pressure Actuated, High-Flow Unloaders from AR Pumps. VRT Series Unloader features brass construction and stainless steel internals. Designed to bypass at near zero pressure. Ports are 3/8” FPT inlet, outlet and bypass on AL607X. Ports are 1/2” F on VRT Series. Rated to 194° F. Part No. Max. PSI Max. GPM Spring Net Ea. AR AL607X 4500 8.0 Black $ 37.95 AR VRT100-190 2800 26 Yellow 88.95 AR VRT100-330 4800 26 Blue 88.95

Pressure Sensitive

Rated GPM

D

550S

Part No. Max. PSI Max. Flow Net Ea. MV VR54-200 2900 8 GPM $ 26.75 MV 550 4500 8 GPM 34.30 MV 550S * 4500 8 GPM 59.95 * Features pressure switch.

High Pressure Unloader Valves Pressure Sensitive Unloader Valves are designed to “trap” pressure when gun is closed and drop bypass pressure to zero. When gun is opened, immediate pressure is available. Designed for single gun applications but can be adapted for multiple guns if required. Standard with brass bodies and buna seals, except for YU2158 which has a stainless body.YVB4021B is for single or multiple guns.

D

D

YU2140

PULSAR4

D

YU5221

Part No.

Ports

Max. Max. Max. GPM PSI Temp.

D

Net Ea.

IP PULSAR4 3/8" FPT IP YVB8KMS * 3/8" FPT IP YU5075K 3/8" FPT IP YU5075KMS * 3/8" FPT IP YU2121 1/2" FPT IP YU2140 1/2" FPT IP YVB4021B 1/2” FPT IP YU2158 ** 1/2" FPT IP YU5221 1" FPT

10 4000 195° F. $ 43.95 8 3200 195° F. 63.95 10 5100 195° F. 113.00 10 5100 195° F. 198.50 21 2300 200° F. 97.50 21 4000 200° F. 101.50 21 4000 195° F. 116.50 21 5800 200° F. 395.00 53 2200 200° F. 299.50 * With 5 Amp / 250 Volt MicroSwitch. ** Stainless Steel Body.

Part No. GU 22911A GU 22971B GU 22083 GU 22090 GU 22912A GU 22913A GU 22973B GU 22080 GU 22095-5

Net Ea.

CC 7670 150 to 1450 2.5 to 8.0 $ 84.45 CC 7694 400 to 4000 2.5 to 10.5 89.50 CC 7690 1000 to 4000 2.5 to 8.0 82.90 CC 7501.100 * 100 to 2000 .5 to 6.0 329.50

D

* 3/8” MPT Ports, 316SS Construction. Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES

MPT Ports

Pressure Actuated Unloader Valves from Giant Industries. All valves shown feature brass housings and stainless steel wetted parts. Can be used in single or multiple gun applications. Designed to bypass at near zero pressure and operate up to the maximum pressures and flow rates shown.

Cat Pumps® Regulating Unloaders. Pressure sensitive feature permits wide range of flows. Handle allows for easy adjustment of system pressure. For single gun, non-weep applications. Optional ports for easy installation. Small compact size. Designed to reduce pressure in the pumping system when trigger guns are used. Takes load off motor or engine when in bypass mode. All ports are 3/8" FPT rated to 180° F. Brass bodies, except No. 7501 which is 316SS . Rated PSI

D

Pressure Actuated Unloader Valves

Regulating Unloaders

Part No.

FPT Ports

YVB8KMS

Pressure Actuated Unloader Valves

VRT100-190

AL607X

VR54-200

High Quality Pressure Unloader Valves. Relieves bypass pressure to zero when in bypass mode. Brass bodies are standard. Available with male or female ports for ease of plumbing. Model 550S features a pressure switch rated to 15 amps and up to 250 volts. Models VR54-200 features 3/8” MPT inlet and outlet and 3/8” FPT bypass. Model 550 features 3/8” FPT inlet and outlet with 1/4” FPT bypass.All are rated to 194° F.

D

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

D

Max. Max. PSI GPM Ports 1400 13 1/2” FPT 1750 35 3/4” FPT 2200 21 1/2” FPT 2200 52 1” FPT 2400 13 1/2” FPT 3000 13 1/2” FPT 4000 26 3/4” FPT 4100 21 1/2” FPT 5200 21 1/2” FPT

553-6975

Spring Color Yellow Yellow White - Red Orange Orange Blue Black

www.dultmeier.com

Net Ea. $ 104.00 322.50 118.50 315.50 104.00 104.00 509.00 125.00 792.00 E0071


Pressure Relief Valves & Unloaders Pressure Relief Valves

K3 & K5 SERIES UNLOADERS — Flow Sensitive —

D

Part No.

IP K3.1 IP K3.2 IP K5.1 IP K5.2 IP K5.3 IP 53129 IP 53158

STANDARD FEATURES: Stainless Steel and Brass internal parts. • No external moving parts or springs. • Unique balance nozzle principle eliminates pressure peaks normally generated by conventionally designed unloaders as well as eliminating high pressure in all lines while unit is in by-pass mode. • Pressure in system during unloading cycle is determined by the inlet pressure to the system. • Motors draw less amps, engines run with less load during unloading cycle. • Piston design permits precise pressure adjustment. Ports: Inlet; 3/8" FPT, Outlet; 3/8" MPT, By-pass; 3/4" MPT. Maximum temperature is 165° F. Best for Single Pump or Non Weep Guns. Pressure Maximum Range PSI GPM Flow Temperature

Net Ea.

700 to 1450 2.9 to 4.3 160° F. 700 to 1450 4.3 to 5.6 160° F. 1450 to 3000 2.9 to 4.3 140° F. 1450 to 3000 4.3 to 6.6 140° F. 1450 to 3000 6.6 to 10.8 140° F. Repair Kit for K3 Unloader................................. Repair Kit for K5 Unloader.................................

$ 68.65 68.65 72.95 72.95 72.95 48.90 52.45

IP K7.1 IP K7.2 IP K7.3 IP 53420

PSI Range

SS 6815-3/4-300 SS 6815G-3/4-700 SS AA110-1/4 SS AA110-3/8 SS 6815-1/2HSS SS 6815-3/4HSS

7450

Type 6815

Type 6815G Brass

300 PSI 700 PSI 1000 PSI 1000 PSI 1200 PSI 1200 PSI

3/4"MPT 3/4"MPT 1/4"MPT 3/8"MPT 1/2"MPT 3/4"MPT

3/4"FPT 3/4"FPT 1/4"FPT 3/8"FPT 1/2"FPT 3/4"FPT

Net Ea.

$ 40.35 74.15 38.95 38.95 83.05 83.15

Features: Viton® Diaphragm • 300 PSI Pressure Range • Aluminum Bonnet • Stainless Steel Springs • Positive Adjustment Lock • Extra Large Valve Passages.

D D

Maximum Flow

Pressure (PSI) 10 20 30 40 60 80 100 Flow Rate (GPM) 22 31 38 44 54 62 70 Maximum Flow rates through valves at various pressures with valves fully open.

Net Ea.

Part No.

4000 PSI 2.5-10.5 GPM

Unloader Control Sets for General Pumps Trapped Pressure Unloader Sets to fit General Plunger Pumps. Compact design eliminates the need for bypass hoses. Easily mounts to either side of pump manifold. Trapped pressure design with internal bypass. Built-in chemical injector with metering adjustment. Rated to 3000 PSI and 200° F.Ports are 1/2” F inlet and 3/8” M outlet.

$ 127.50

Unloader Valve Control Sets — Pressure Sensitive — One Piece Pressure Control Sets that include: Unloader Valve, Chemical Injector and Port Connections to fit many types of Plunger Pumps. D

Features: Brass Construction • Ports that are 1/2” FPT inlet x 3/8” MPT outlet • Chemical Injectors are adjustable for injection rate • Universal fit for a wide range of pumps. Part No. Flow Rate Max. PSI Net Ea. AR AR21039 2-3 GPM 2600 $ 67.10 AR AR21040 3-4 GPM 2600 67.10 AR AR20400 3-5 GPM 3650 79.15

Diaphragm By-Pass Valves Net Ea.

SS 8460-3/4 Nylon Valve ................... $ 33.35 SS 9840-3/4 Brass Valve ................... 97.50 SS 8366VI Viton® Diaphragm Only 10.40 SS RK8460 Viton® Repair Kit .......... 12.50 SS 8361-3/4NY Nylon Repair Body ....... 11.25

Flow Sensitive Unloaders from Cat Pumps®. Flow actuated bypass. Nominal pressure spikes for smoother operation. Provides protection for single gun, non-weep installation. Reduced pressure loss means more cleaning power. Rated to 4000 PSI. Flows from 2.5 to 10.5 GPM. Maximum temperatures to 195° F. Inlet, outlet and bypass ports are all 3/8” FPT. Pressure Flow Part No. Switch Range Range Net Ea.

No

Type 110

Ideal for use with Spot-Free Transfer Systems. These Diaphragm Style Pressure Relief Valves are available with a nylon or brass lower body. Connections are 3/4" NPT with a 1/4" FPT gauge port.

100 to 3000 3.0 to 4.0 GPM $ 87.15 100 to 3000 4.0 to 6.6 GPM 87.15 100 to 3000 6.6 to 10.6 GPM 87.15 Repair Kit for K7 Unloader..... 76.10

CC 7450

D

D

Diaphragm Pressure Relief Valves

Flow Sensitive Unloaders

D

D

Maximum Ports Pressure Inlet Outlet

Part No.

— Flow Sensitive —

Part No.

SPRAYING SYSTEMS AA110 & 6815 SERIES piston type pressure relief valves are adjustable to maintain control of line pressure at any point within the valve operating range. Special inner rib construction provides flushing action around shut-off piston and springs. AA110 Series available in 1/4" or 3/8" NPT ports. 6815 Series available with 1/2" or 3/4" NPT ports. Constructed with brass body, Stainless Steel spring and hardened Stainless Steel seat and inlet adapter. Rated to 150° F. Buna Gaskets.

* PRESSURE IN PSI 10 20 30 40 60 80 100 AA110 Max. Flow 5.3 7.5 9.2 11 13 15 17 6815 Max. Flow 10 14 16 18 20 22 23 * With pressure adjusting screw backed off to full open.

K7 Series Unloaders STANDARD FEATURES: All Stainless steel and brass internal parts. No external moving parts or springs. • Unique barb and flow balancer design provides gradual pressure build-up when system is closed. • Eliminates high pressure in all lines while unit is in by-pass mode. • By-pass restrictor eliminates pressure peaks during by-pass. • Balanced piston design permits precise pressure adjustment. • Simple design offers easy maintenance and service. Ports: Inlet and by-pass ports are 3/8" FPT. Outlet port is 3/8" MPT. Maximum Temperature: 165° F. Note: These valves require a minimum of 5% by-pass at all times. Best for Single Pump or Non Weep Guns.

102

Model ZKW21, ZKW21L Model ZKW21 used on pump models: Model ZKW21L used on pump models:

2.9 - 4.5 GPM TS1371, TT1411, TT1611, TT9351 TT9441, TT9971, All EZ Pumps T811, TS1011, TS1311, TS 1331, TS1511, TS1711, TS2011, T9131, T9211

Model ZKW22L Model ZKW22L used on pump models:

4.5 - 6.0 GPM T821, T921, T1021, T1321, T1621, T9121, T9161, TS821, TS921, TS1321, TS1521, TS1621, TS2021

Part No. IP ZKW21 IP ZKW21L IP ZKW22L

D

Flow Range Net Ea. 3.0 - 4.5 GPM $ 99.05 3.0 - 4.5 GPM 99.05 4.5 - 6.0 GPM 99.05

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0070


High Pressure Relief Valves

103

Balanced Pressure Regulators

Balanced Relief Valves Ideal for Car Washes with Weep Guns

For accurate, repeatable by-pass regulation wherever absolute reliability in pump output control is necessary. Continually regulates pressure within 5% of setting. Can be set up to both regulate and absorb normal pulsation thus eliminating the need for a pulsation dampener. Can be parallel mounted. Responds in .004 seconds or less. Designed for Weep Systems.

D

Materials: Body and Stem; Steel, Electroless Nickel plated. Piston Cap & Inlet Cap; 416SST hardened stainless steel. Springs; Spring steel. Seals; Viton®. Maximum temperature 250° F. NOTE: Requires 5% minimum by-pass. Not recommended for use with single or two cylinder pumps.

Features: Maximum operating pressure is 3600 PSI • Maximum operating temperature is 200 ° F. • Maximum flow rate is 8 gpm • Inlet and bypass port are 1/4" FPT. • Construction is a brass housing with stainless steel piston and seat.

D

Maximum FPT Ports Part No. Capacity Pressure Range Inlet Outlet UP BR5-1 5 GPM 100 to 1000 PSI 3/8" 1/4" UP BR5-1.5 5 GPM 500 to 1500 PSI 3/8" 1/4" UP BR5-2 5 GPM 750 to 2000 PSI 3/8" 1/4" UP BR10-1 10 GPM 100 to 1000 PSI 1/2" 1/4" UP BR10-1.5 10 GPM 1000 to 1500 PSI 1/2" 1/4" UP BR10-2 10 GPM 750 to 2000 PSI 1/2" 1/4" UP 32005 Washer Spring set for BR5-2 .................................... UP 40027 Repair Kit for BR5 Relief Valves................................ UP 40028 Repair Kit for BR10 Relief Valves..............................

Part No.

Net Ea. $ 57.95 62.95 56.95 141.50 155.50 168.00 24.00 5.51 7.65

Hydra-Cell Bypass Valves Designed to handle the same rigorous demands as the Hydra-Cell pumps. These valves will bypass total system flow when required and will also balance system pressure for multiple gun operations. Standard valves feature Brass bodies with Buna O-rings and stainless valve seats and plunger ball. Rated to 160° F. (200° available on special request). Model C62B features Viton®/Teflon O-rings and diaphragm and is rated to 200° F.

BALANCED RELIEF VALVES

D

D D

579

3300-84

D

Pressure Maximum Part No. Range Flow Net Ea. SM 579 100 - 1000 PSI 4-GPM $ 22.95 SM 3300-84 200 - 2000 PSI 10-GPM 31.00 SM 3300-84S * 200 - 2000 PSI 10-GPM 97.90 SM 3300-84M 200 - 2000 PSI 10-GPM 31.20 SM 3300-87 200 - 2000 PSI 7-GPM 33.30 SM 3300-87M 200 - 2000 PSI 7-GPM 38.80 IP YBRV5325 0 - 2500 PSI 53-GPM 129.00 IP Y60511024 Repair Kit, YBRV5325.................. 23.95 SM 2111-2 Repair Kit, 3300-84 & 87............. 3.40 * Stainless Steel

YBRV5325

Part No. Max. PSI Max. Flow Net Ea. GU 22760A 3000 8 GPM $ 66.40 GU 22765A 4000 5 GPM 92.55

High-Flow Pressure Regulators

Vacuum Switches

Vacuum Rating

1.5 Hg vac 2.5 Hg vac 4.5 Hg vac

High Pressure, High Flow Pressure Regulator Valves from CAT PUMPS®. Rated to flows of up to 35 GPM and pressures to 2000 PSI. Commonly used in conjunction with Cat 35FR pumps. Stainless steel and Viton® internal parts for durability. In-line, flowthro design for ease of installation.

D

Can be used in tunnel arches or in single gun and multiple gun wash systems. Zero system pressure variation with each additional gun added to the system.

D

Inlet and outlet ports are 3/4" FPT. Bypass port is 1" FPT. Dimensions: 8-1/2" high x 2-1/4" diameter. Weight is 5-1/2 lbs. Part No. Min. Flow

Net Ea.

$ 16.95 16.95 16.95

Models 3300-87 & 87M are designed to mount “in-line”. Rate to 7 gpm at pressures from 200-2000 PSI.3300-87 has 3/8" FPT on all ports. 3300-87M is 3/8" MPT inlet x 3/8" FPT outlet and bypass. Rated to 180° F. Model YBRV5325 is a high flow unit that is designed to mount “off-line”. Rated to 53 gpm at pressures to 2500 PSI. Inlet port is 3/4" FPT. Bypass is 1/2" FPT. Rated to 195° F. Can be used in multiple gun applications.

D

— Not for use with Weep Guns —

HY 2510-1 HY 2510-7 HY 2510-17

3300-87

3300-84M

High Pressure, Low Cost Pressure Activated Unloaders from Giant. Ideal for multiple gun applications. Brass and stainless steel construction. Inlet and outlet ports are 3/8" FPT. (2) 1/4" FPT bypass ports for ease of plumbing. Maximum temperature is 160° F.

Part-No.

Models 3300-84 & 84M are designed to mount “off-line and are rated to 10 gpm at pressures from 200-2000 PSI. 3300-84 has 3/8" FPT inlet and bypass. 3300-84M has 3/8" MPT inlet and 3/8" FPT bypass. Rated to 180° F. (3300-84S is stainless steel).

D

Pressure Actuated Unloaders

Net Ea.

$ 26.00 11.75

Balanced Pressure Regulators are designed so that working pressure and bypass pressure are “balanced” in the system. Ideal for weep style trigger wands because there is no valve cycling and pressure is constant. Can also be used on large flow pumps for pressure regulation and control. Bodies are brass with Buna o-rings. Model 579 is a “mini” regulator rated to 4 gpm at pressures from 100-1000 PSI. Designed to be mounted “offline”. Ports are 1/4" MPT inlet x 1/8" FPT bypass. Rated to 180° F.

Note: Valves with other pressure ranges are available on request.

Vacuum Switches protect pumps from running dry by automatically shutting off motors when liquid is depleted or vacuum drops to a specific level. Rated for 110 volt or 220 volt up to 16 amps. Three Hg Vac. ratings to choose from. Rated to 140° F. Inlet port is 1/4" FPT.

Maximum Maximum PSI GPM

NP ST230 Balanced Relief Valve 3600 8 NP RK230 Repair Kit for ST230...........................

Part No. Flow Rate Pressure Range Ports Net Ea. WN C22A 3-10 GPM 500-1000 PSI 3/4" FPT $ 212.00 WN C23A 10-20 GPM 500-1000 PSI 1" FPT 296.00 WN C24A 20-40 GPM 500-1000 PSI 1-1/4" FPT 679.00 WN C62B 1-14 GPM 500-2500 PSI 3/4" FPT 244.00

D

ST230 Balanced Pressure Relief Valve. Ideal for use in carwash installations using “weep” trigger guns. Designed to be mounted “off-line.”

Max. Flow PSI Range

Net Ea.

CC 7021 2.5 GPM 25 GPM 200-1000 $ 596.00 CC 7031 3.5 GPM 35 GPM 700-1000 819.00 CC 7032 3.5 GPM 35 GPM 1000-2000 819.00 CC 30783 Repair Kit................................... 35.90

1/4” Inlet

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0069


Pump Accessories Thermal Relief Valves

Pulsation Dampeners For reducing vibration and pulsation in pumping systems. Prolongs pump and component life. Available in rechargeable or sealed models.

D D D

Note: Ideal pre-charge is 1/2 of the operating pressure of the pump but should not exceed 50% of the maximum operating pressure of the dampener.

6028 & 686028

D

D

7100 Series

Max. Max. MPT Part-NO GPM PSI Inlet Make Lower Body Net Ea CC 6028 * 15 1000 1/2" Cat Coated Steel $ 155.00 IP 686028 * 10 3000 1/2" General Coated Steel 119.50 CC 6029 15 3000 1/2" Cat Stainless Steel 209.50 CC 6011 25 7200 1/2" Cat Coated Steel 1081.00 CC 6010 40 3000 1" Cat Coated Steel 283.50 IP 686010 40 4000 1" General Coated Steel 249.50 CC 6012 70 1500 1-1/4" Cat Coated Steel 797.00 * Model 6028 and 686028 are sealed & not rechargeable.

Pulsation Dampeners

Thermo-Valves protect pumps from pre­mature failure of seals, packing and cups by eliminating heat build-up in closed loop by-pass systems. Automatically seats during un­loader/regulator pressure spikes to prevent fluid bleed.

Outlet

Standard Features include: Buna-N Bladder • Nitrogen pre-charge • Bottom port for easy mounting • Sealed valve for positive pressure lock • Maximum operating temperature is 180° • Standard pre-charge is 550 PSI.

D

104

3312 Series

100558

23422A

Valves open when temperature exceeds temperatures shown. Provides high temperature protection without interruption in flow. Compatible with systems using either unloader or regulator valves. Part No. NP 9063 GU 23421A GU 23422A IP 100558 HY 3312-4 CC 7140 CC 7141 CC 7142 CC 7170 CC 7171 CC 7172

3375-15

Helps to minimize pulsation in piston & plunger pumps. Protects pump & system from hydraulic shock.

D

Max. Max. Maximum Flow Press. Temperature Inlet 6-GPM 200 PSI 140° F. 3/8"MPT 8-GPM 90 PSI 140° F. 3/8”MPT 8-GPM 90 PSI 140° F. 1/2"MPT 8-GPM 200 PSI 145° F. 1/2”MPT 10-GPM 200 PSI 145° F. 1/2"MPT 25-GPM 125 PSI 145° F. 1/4"MPT 25-GPM 125 PSI 145° F. 3/8"MPT 25-GPM 125 PSI 145° F. 1/2"MPT 25-GPM 125 PSI 180° F. 1/4"MPT 25-GPM 125 PSI 180° F. 3/8"MPT 25-GPM 125 PSI 180° F. 1/2"MPT

Outlet - - - 1/4” FPT 1/4” FPT 1/8"FPT 1/8"FPT 1/8"FPT 1/8"FPT 1/8"FPT 1/8"FPT

Pop-off Relief Valves

D

ZKSR

22050 & 22155

Safety Relief "Pop-Off" Valves. For use as safety back-up valves to your unloaders or regulators. Brass and stainless steel construction. Model ZKSR and 100534 have 3/8" MPT inlet. Model SV1200 has 1/2" MPT inlet. Model ZKS3 has 1/2" MPT inlet.

Heavy-Duty Pulsation Dampeners. Pre-charged with dry nitrogen. Assures smooth discharge from high pressure pumps. Reduces vibration and wear on pump parts and accessories. Diaphragms are Buna-N. Model 22050 & 22155 is GIANT brand and features 303SS Steel housing. Rated to 200° F. 3300 Series are HYPRO brand with ductile iron housings. These dampeners are rated to 140° F. Maximum * Maximum Part-No. Ports Capacity Pressure PreCharge GU 22050 3/8" MPT 12 GPM 3000 PSI 600 PSI GU 22155 3/4" MPT 30 GPM 3000 PSI 600 PSI GU 22028 Replacement Diaphragm for 22050 Dampener HY 3375-173 1/2" FPT 6 GPM 1500 PSI 300 PSI HY 3375-175 1/2" FPT 6 GPM 1500 PSI 500 PSI HY 3375-15 1" FPT 35 GPM 1500 PSI 300 PSI HY 3375-15-5 1" FPT 35 GPM 1500 PSI 500 PSI HY 3375-156 1" FPT 35 GPM 1500 PSI 600 PSI HY 3375-157 1" FPT 35 GPM 1500 PSI 700 PSI

Part No. Max. Flow IP 100534 6 GPM IP ZKSR 11 GPM IP ZKS3 21 GPM IP SV1200 50 GPM IP SV1500 50 GPM

D

Net Ea. $ 84.95 155.50 6.60 119.50 119.50 186.00 186.00 186.00 186.00

100534

Pulse Hose D

Part No. Length Net Ea. HY 3375-8 24" Rated to 3 gpm @ 1500 PSI $ 9.77 HY 3375-11 40" Rated to 5 gpm @ 1500 PSI 11.50 NOTE: Multiple hoses can be used to increase flow capacities.

Stainless Steel Pop-Off Valves

DULTMEIER SALES

OMAHA, NE (800)

228-9666

Net Ea. $ 13.30 35.95 327.00 256.00 255.50

D

Reduce system pressure upon even a partial obstruction. Used in conjunction with an unloader valve, your pumping system actually has two safety relief valves. Brass construction with Stainless Steel ball and press formed seat. Inlet ports are 1/4" or 3/8" MPT. Valves can be reset in the field if necessary. 160° F. maximum temperature. Outlet is 3/4" FPT.

Reduces Vibration & Pulsation in Pumping Systems

D Stainless Steel, High Temperature PopOff Valves are designed to protect pumps and plumbing systems from failure of main relief or unloader valves. Cat Pumps 100971 valves are rated to 240° F. General Pump valves are rated to 284° F. Flow Max. Part-No. Inlet Rate Mfr. PSI Net Ea. CC 9960 1/4" MPT 6 GPM Cat Pumps 1500 $ 77.50 CC 9962 1/4” MPT 6 GPM Cat Pumps 4000 77.50 IP 100971 3/8” MPT 7 GPM General 4500 24.95 IP 100982 3/8” MPT 12 GPM General 4500 24.95 IP 100972 1/2” MPT 7 GPM General 4500 24.95 CC 890710 1” MPT 100 GPM Cat Pumps 1500 1069.00 CC 890711 1” MPT 50 GPM Cat Pumps 6000 1069.00

Max. PSI 6,000 3,000 10,000 2,900 7,250

Pop-Off Relief Valves

* Note: Pre-charge should not exceed 50% of Maximum pressure.

3/8" MPT Inlet x 3/8" Plug Outlet

Net Ea. $ 7.77 5.51 5.31 5.70 44.70 29.90 29.95 29.90 35.55 35.25 34.40

Part No.

MPT Max. Size Flow Mfg.

Max. PSI

NP 9069 GU 22568 GU 22531A GU 22533A

3/8" 6 GPM Suttner 4000 $ 9.27 1/4” 10 GPM Giant 5000 8.11 3/8" 10 GPM Giant 2400 8.13 3/8" 10 GPM Giant 5000 8.13

Net Ea.

Safety Pop-Off Valves Safety Pop-Off Valves are designed to protect pumps in the event an unloader or regulator valve fail. Should be used in conjunction with a regulator or unloader valve. Brass Body, hardened stainless seat, lightweight and compact design. Rated to 180° F.

D

Part No.

Maximum Pressure Flow Adjustment Range MPT Inlet Net Ea.

CC 33960 CC 30961 CC 33961 CC 9940

6-GPM 300 to 1500 PSI 6-GPM 1000 to 3000 PSI 6-GPM 1000 to 4000 PSI 25-GPM 1000 to 4000 PSI

3/8" 1/4" 1/4" 3/4”

D

$ 33.95 30.30 33.25 117.50

9960 •

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0089


Chemical Injectors

105 Brass or Stainless Body

Brass or Stainless Body

D

SERIES B INJECTORS

SERIES C INJECTORS

SERIES B Chemical Injectors are standard Water Flow with water flow adjusting screw for easily Control matching to your pump flow. Standard models Chemical are designed for upstream injection. Use BS Flow Control models for downstream injection. Standard Ryton Chemical Port, chemical block has chemical metering screw. “T” Plastic or Stainless Series models have 15 metering tips in place of the metering screw for specific injection rates. Brass bodies are standard. Rated to 160° F. Ports are FPT x FPT. All injectors come with 8’ chemical tube with strainer. BP INJECTORS feature a special plastic chemical port for aggressive/ corrosive solutions. BS INJECTORS feature a stainless INJECTOR CAPACITIES chemical port for pressures from 700 to MAXIMUM INJECTION 3,000 PSI. FLUID OUNCES PER MINUTE BS2 INJECTORS feature a stainless VISOCITY body and chemical ports for pressures CPS 202B 203B 204B 206B 1 8 16 36 42 to 3,000 PSI. 75 4 8 13 18 BT INJECTORS Injectors feature a 220 2 4 5 8 standard body with 15 piece tip kit. 500 1 2 2 4

SERIES C Chemical Injectors are Standard standard with multiple flow orifices to match with properly to the flow rate of your pump. Can Metering Screw be used for upstream injection as well as downstream injection to 700 PSI. (3,000 PSI if stainless metering barb is ordered). Standard Ryton chemical block has chemical metering screw.   “T” Series models have 15 metering tips in place of the metering screw for specific injection rates. Brass bodies are standard. Rated to 160° . Ports are FPT inlet x MPT outlet. All injectors come with 8’ chemical tube with strainer.

*24-50 Models feature Ryton chemical body with 1/8” MPT inlet port for rigid mounting.

INJECTOR SELECTION TABLE OPERATING RANGE WATER GALLONS PER MINUTE PRESSURE PSI 202B 203B 204B 206B 10 .25-2.0 .50-3.5 2.0-6.4 3.6-11 20 .30-2.3 .55-4.4 2.3-7.5 4.2-13 40 .37-2.9 .70-5.4 2.9-9.5 5.3-17 60 .43-3.4 .80-6.4 3.4-11 6.2-19 100 .54-4.2 1.0-8.0 4.2-14 7.7-24 200 .73-5.7 1.4-11 5.7-19 11-33 400 1.0-7.9 1.9-15 7.9-26 15-46 500 1.2-8.9 2.1-17 8.9-29 17-51 **700 1.4-11 2.5-20 11-35 20-60 **1000 1.6-13 3.0-23 13-41 23-70 **1500 2.0-16 3.5-28 16-50 28-87 **2000 2.2-18 4.7-37 18-58 33-100 **3000 2.7-20 5.0-45 20-70 40-100 ** Use BS Series for Over 700 PSI.

1000 0.5 1 1 1

Part No. Ports DE 202B 3/8" FPT DE 202BP 3/8” FPT DE 202BS 3/8” FPT DE 202BT 3/8” FPT DE 203B 3/8" FPT DE 203B-2450 * 3/8” FPT DE 203BP 3/8” FPT DE 203BS 3/8” FPT DE 203BS-2 3/8” FPT DE 203BT 3/8” FPT DE 204B 1/2" FPT DE 204BP 1/2” FPT DE 204BS 1/2” FPT DE 204BT 1/2” FPT DE 206B 3/4" FPT DE 206BP 3/4” FPT DE 206BT 3/4” FPT

Net Ea. $ 46.50 48.10 56.35 47.40 46.50 55.90 49.60 56.35 90.45 47.25 50.50 53.65 60.85 50.80 62.95 72.85 65.25

INJECTOR SELECTION TABLE - TOTAL SPRAY NOZZLE FLOW-GPM MODEL PRESSURE - PSIG NO. 10 20 40 60 100 300 500 **750 **1000 200-3C .10-.20 .13-.26 .17-.34 .21-.41 .26-.52 .44-.92 .57-1.2 .70-1.4 .80-1.7 200C .20-.39 .26-.51 .34-.68 .41-.82 .52-1.0 .92-1.8 1.2-2.3 1.4-2.8 1.7-3.2 202C&T .79-1.6 1.0-2.0 1.4-2.7 1.6-3.3 2.1-4.2 3.6-7.3 4.6-9.3 5.6-11 6.4-13 203C&T 1.6-3.2 2.0-4.1 2.7-5.5 3.3-6.6 4.2-8.3 7.3-15 9.3-19 11-23 13-26 204C&T 3.2-6.3 4.1-8.2 5.5-11 6.6-13 8.3-17 15-30 19-38 23-47 26-53 206C&T 6.3-13 8.2-16 11-22 13-26 17-33 30-57 38-73 47-86 53-101 208C&T 13-25 16-33 19-39 26-53 33-67 47-94 61-99 73-99 86-99 ** Use CS Series for Over 700 PSI. Viscosity - CPS Part No. Inlet Outlet Net Ea. 1 Water DE 200C * 1/8" FPT 1/8" MPT $ 36.35 75 10 wt. Oil DE 200-3C * 1/8" FPT 1/8" MPT 36.35 200 30 wt. Oil or dish detergent DE 202C 1/4" FPT 1/4" MPT 36.35 500 Honey

DE 203C DE 204C DE 206C DE 208C DE 202CT DE 203CT DE 204CT DE 206CT DE 208CT

3/8" FPT 1/2" FPT 3/4" FPT 1" FPT 1/4" FPT 3/8" FPT 1/2" FPT 3/4" FPT 1" FPT

3/8" MPT 1/2" MPT 3/4" MPT 1" MPT 1/4" MPT 3/8" MPT 1/2" MPT 3/4" MPT 1" MPT

Integrated Solenoid/Injectors Injector with on/off control. See “Injector Selection Table” covering series “C” injectors to determine flow and pressure parameters. 150 PSI maximum pressure differential. Solenoids are available in 12, 24 or 110 volt.

Ideal for injection of soaps, acids, waxes or disinfectants into the high-pressure, downstream side of your pumps. Used in conjunction with a “Hi-Lo” nozzle, these injectors keep aggressive chemicals from damaging your pumps. All injectors are standard with an adjustable metering knob for variable injection rates. “A” Series Injectors are rated to 3600 PSI and features a brass body, Viton® o-ring, MPT x MPT or MPT x FPT. Maximum temperature is 300° F.

24 or 110-Volt AC

D

“Y2” Series Injectors are rated to 4000 PSI and feature brass body, stainless steel seat, SS ball, SS spring and EPDM O-rings. Maximum temperature is 195° F. (General Pump Brand) “YSS” Injectors* are rated to 5800 PSI and feature all stainless steel construction with Viton® & Teflon O-rings. Maximum temperatures is 195° F.

Maximum Part No.

Flow Range

Pressure

Inlet x Outlet

Net Ea.

AA A7227 2.0 - 3.8 gpm 3000 PSI 3/8" MPT x 3/8" MPT $ 11.20 AA A7228 2.7 - 5.0 gpm 3000 PSI 3/8" MPT x 3/8" MPT 11.20 AA A7229 3.3 - 6.5 gpm 3000 PSI 3/8" MPT x 3/8" MPT 11.20 AA A7547 2.0 - 3.8 gpm 3000 PSI 3/8" FPT x 3/8" MPT 19.70 AA A7548 2.7 - 5.0 gpm 3000 PSI 3/8" FPT x 3/8" MPT 19.70 AA A7549 3.3 - 6.5 gpm 3000 PSI 3/8" FPT x 3/8" MPT 19.70 AA A7337 Repair Kit for A Series.......................................... 8.14 IP Y218 2.0 - 2.6 gpm 4000 PSI 3/8" MPT x 3/8" MPT 17.90 IP Y221 2.6 - 4.0 gpm 4000 PSI 3/8" MPT x 3/8" MPT 18.10 IP Y223 4.0 - 5.3 gpm 4000 PSI 3/8" MPT x 3/8" MPT 18.10 IP YSS18 * 2.0 - 3.0 gpm 5800 PSI 3/8" MPT x 3/8" MPT 53.15 IP YSS21 * 3.0 - 5.0 gpm 5800 PSI 3/8" MPT x 3/8" MPT 53.15 IP YSS23 * 5.0 - 8.0 gpm 5800 PSI 3/8" MPT x 3/8" MPT 53.15

38.60 40.55 50.15 71.85 38.95 40.95 42.75 49.25 73.50

* Best for Foam Brush Applications.

DOWN STREAM INJECTORS

D

D

- 12 Volt Also Available Part No. Control Injector AC-Volts Ports Net Ea. DE 204V-24 Single C 24 1/2" $ 72.85 DE 204V-110 Single C 110 1/2" 72.85

Visit Our Web Site at http://www.dultmeier.com or E-Mail us at dultmeier@dultmeier.com

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0102


Chemical Injectors

106

ChemFlex Injectors

6350 Pulse Pump Pulse Pump from Cat Pumps® permits chemical injection at pressures up to 3000 PSI. Mounts on the center inlet port of many Cat Pumps and is activated with each stroke of the pump. Includes a prime bulb to start chemical. Requires correct 76400 Series adapter for specific Cat Pumps® models. D

Innovative Chemical Injectors for use with Automatics, Self-Serve Systems and even pressure washers applications. 3/8” MPT stainless steel inlet and outlet ports and PVDF/Kynar injection bodies with Teflon o-rings, ensure the highest chemical and corrosion resistance available. Note: 120083 features EPDM O-ring.

Color coded and clearly marked for a wide variety of flow ranges. Available with single, double and triple chemical barbs for injection of more than one chemical at the same time. Slip-in replacement for injectors used on most of the common high pressure automatics in the car wash industry. Chemical barbs are 1/4” and are standard with internal threads to accept a wide range of orifice tips, (sold separately). Rated to 1000 PSI and 175° F. Part No. Color Nozzle

Shown Mounted on Cat Pump

Threaded fitting to allow for installation of metering tips

Call Us for Details !

110057

Adjustable Injector

Hastelloy® spring

D

Upstream Injectors These adjustable injectors are designed to introduce chemicals into the upstream side of pumps. This allows for high pressure chemical applications. Brass body with stainless ball and spring are standard. Ports are 1/2" FPT inlet and 1/2" MPT outlet. 4' of tubing with strainer is also included. Rated to 140 PSI. Flow Rate

Ports

Net Ea.

1.5 - 3.9 gpm 4.0 - 7.0 gpm

1/2" 1/2"

$ 29.65 29.70

60 (TC) 44 (EZ) 63 (TX) 47 66 (TSF)

520222 520197 520197 520190 520223

Part No.

103036 103036 103036 103035 103090

Pulse Pump Injectors from General Pump are designed to inject chemicals with every stroke of the pump. Designed to mount to the valve port of General Pump models. Construction is 303 Stainless Steel with Buna diaphragm. Inlet and outlet are 1/8” FPT, pulse port is 1/4” FPT. To convert existing pumps, one adapter and one valve assembly is also required from the chart shown.

Maximum Maximum Pressure Flow

IP 100906 Pulse Pump 1500 PSI .75 GPM Viton® is a registered trademark of DuPont Performance Elastomers DULTMEIER SALES

Chem-Flex comes in many convenient sizes, body color is coded to the nozzle size

110098 0.098 in.

OMAHA, NE (800)

Flow Office

*Flow Range

No. of Barbs

Color

HF 110057 .057 1.0 GPM 1 Red HF 110070 .070 2.2 GPM 1 Orange HF 110083 .083 2.3 GPM 1 Grey HF 110086 .086 2.5 GPM 1 Blue HF 110098 .098 4.0 GPM 1 Green HF 121057 .057 1.0 GPM 2 Red HF 121070 .070 2.2 GPM 2 Orange HF 121083 .083 2.3 GPM 2 Grey HF 121086 .086 2.5 GPM 2 Blue HF 121098 .098 4.0 GPM 2 Green HF 131057 .057 1.0 GPM 3 Red HF 131070 .070 2.2 GPM 3 Orange HF 131083 .083 2.3 GPM 3 Grey HF 131086 .086 2.5 GPM 3 Blue HF 131098 .098 4.0 GPM 3 Green DE 100-15K Tip Kit, Standard..................................... * Flow based on 250 PSI incoming water pressure. ** Standard with EPDM O-ring.

Pulse Pump Injector

PUMP ADAPTER VALVE SERIES FITTING ASSEMBLY

110086 0.086 in.

Convenient NPT attachment

D

Part No.

D

Teflon

120083 0.083 in.

Max. Flow Part No. PSI Rate Net Ea. NP ST62 3600 5 GPM $ 21.95

NP ST64 NP ST64-5

110083 0.083 in.

Insert molded Kynar® body is resistant to chemicals & corrosion

Adjustable Chemical Injector from Suttner. Forged brass housing with stainless steel spring and ball. Rated to 3600 psi. Large control knob for easy adjustment. Siphon rate of up to 10:1. Inlet and outlet ports are 3/8” FPT. Chemical barb is 1/4”.

Part No.

0.057 in.

Barb Fitting Proprietary O-ring for increased chemical resistance to reduce O-ring swelling

D

D

Net Ea.

$ 239.00

228-9666

Net Ea.

$ 37.95 37.95 37.95 37.95 37.95 48.75 48.75 48.75 48.75 48.75 71.95 71.95 71.95 71.95 71.95 7.10

Stainless Steel Chemical Injectors Stainless Steel Chemical Injectors for use as replacements in many common Automatics such as PDQ Systems.Injectors are stainless steel construction with 3/8" MPT inlet and outlet. Chemical barbs are 1/4" hose barb with internal threads for "screw in" metering tips, (not included). Rated to 5500 PSI. 316SS, Viton® seal. Rated to 190° F. Available in single barb or dual barb models.

Part No. Orifice Barbs. GPM IP 100336 .057 1 1-2 Dual Barb IP 100835 .070 1 2-3 No. 100541 IP 100334 .083 1 2-4 IP 100333 .086 1 3-5 D IP 100339 .098 1 5-8 IP 100541 .083 2 2-4 DE 100-15K Tip Kit, Standard DE 100-15KU Tip Kit, Ultra Lean IP 100464 Repair Kit DAVENPORT, IA (800) 553-6975 • www.dultmeier.com

Color Coded Metering Tips Are Optional

D

Net Ea. $ 25.95 38.15 25.95 25.95 25.95 51.95 7.10 4.07 16.95 E0777


Chemical Injectors

107

Bypass Lever

Chemical Injectors Self-Priming, Fluid Driven Proportional Injectors. Uses water flow as the power source, no electricity is required. Injection ratios are consistent regardless of variances of flow or pressure. Chemical-resistant bodies and internals with Viton® seals. Built in stop/start switch to allow injection to stop without affecting water flow. Injection ratio can be adjusted while unit is operating. 3-Year Warranty. Made in the USA.

Chemilizer is an Industry-Leading, Water-Driven Chemical Injector designed for a wide variety of applications including car/truck wash, animal health, horticulture and food processing. Powered by the water flow, the internal motor drives the chemical pump. Extremely precise and accurate. Injection rates stay consistent no matter if changes occur in water flow or pressure. Features: Polypropylene housing and Viton® diaphragm • Rated to 100° F. • Viscosities to 1500 cps. • Ports are 3/4” MPT • Rated from 3 to 85 PIS and .02 to 11 GPM.

D

Features: Rated to 100° F. • Vertical suction to 13’ and horizontal suction to 49’ • Maximum viscosities to 1500 cP, (Honey) • Ports are NPT but BSP also available • Models are rated from 7 GPM to 100 GPM for nearly any application • 140 Mesh (104 micron) inlet strainer is required for valid warranty.

Ideal for use in the following markets: Animal Health, Horticulture, Food Processing, Vehicle Wash, Pest Control, Water Treatment and many more . . .

D

Chemilizer Injectors

1009 Series are pump cartridges only to convert existing fixed rate Chemilizer units to the new adjustable rate design. Easy 1/4 turn installation.

Bypass Lever

Corrosive Kits Available for most models. Injects solutions downstream or “in series”. For aggressive applications. Chemicals do not enter unit.

D

Adjustable Chemilizer

D

D

1009 Series Chemilizer

Part No. Style Injection Rate Wt. Net Ea.

DM SCT

Up to 12 GPM Units Port Flow Pressure Injection Part No. Size Range Range Ratio Net Ea. DM 116384 1/2” NPT .03 to 3.5 GPM 6 to 100 PSI * 100 to 1 $ 229.50 DM 116381 1/2” NPT .03 to 3.5 GPM 6 to 100 PSI 1:200 to 1:50 226.00 DM 116383 1/2” NPT .03 to 3.5 GPM 6 to 100 PSI 1:50 to 1:20 229.50 DM 116385 1/2” NPT .03 to 3.5 GPM 6 to 100 PSI * 10 to 1 383.00 DM 112638 3/4” NPT .03 to 12 GPM 6 to 140 PSI 1:4000 to 1:250 362.00 DM 112630 3/4” NPT .03 to 12 GPM 6 to 140 PSI 1:500 to 1:100 269.00 DM 112632 3/4” NPT .03 to 12 GPM 6 to 140 PSI 1:200 to 1:40 269.00 DM 112634 3/4” NPT .03 to 12 GPM 6 to 140 PSI 1:100 to 1:20 362.00 DM 112606 3/4” NPT .07 to 10 GPM 6 to 65 PSI 1:50 to 1:10 549.00 DM 112620 3/4” NPT .07 to 10 GPM 6 to 65 PSI 1:25 to 1:5 1019.00 DM SCT-M Corrosive Transfer Kit, 12 GPM............................................ 51.95 * Fixed Injection Range.

15 & 20 GPM Units Port Flow Pressure Injection Part No. Size Range Range Ratio Net Ea. DM 113228 1” NPT .04 to 20 GPM 5 to 100 PSI 1:4000 to 1:333 $ 479.00 DM 113202 1” NPT .04 to 15 GPM 3 to 60 PSI 1:500 to 1:40 297.50 DM 113206 1” NPT .04 to 20 GPM 5 to 100 PSI 1:250 to 1:20 619.00 DM 113207 1” NPT .04 to 20 GPM 5 to 65 PSI 1:50 to 1:10 969.00 DM SCT Corrosive Transfer Kit, 20 to 45 GPM................................... 61.05

30 GPM Units Port Flow Pressure Injection Part No. Size Range Range Ratio Net Ea. DM 113229 1” NPT .15 to 30 GPM 5 to 100 PSI 1:4000 to 1:333 $ 579.00 DM 113209 1” NPT .15 to 30 GPM 5 to 100 PSI 1:500 to 1:40 433.00 DM 113210 1” NPT .15 to 30 GPM 5 to 100 PSI 1:250 to 1:20 633.00 DM SCT Corrosive Transfer Kit, 20 to 45 GPM................................... 61.05

45 GPM Units

DM CH9000-AV1 DM CH9000-AV2 DM CH9000-AV3 DM 10095982 DM 10095929 DM 10095984

Injector Injector Injector Pump Only Pump Only Pump Only

20:1 to 64:1 50:1 to 164:1 150:1 to 500:1 20:1 to 64:1 50:1 to 164:1 150:1 to 500:1

8 lbs. 8 lbs. 8 lbs. 2 lbs. 2 lbs. 1 lbs.

$ 269.00 269.00 269.00 101.50 81.50 101.50

Adjustable Chemical Injectors Adjustable Chemical Injectors from Spraying Systems. Features needle valve to control chemical injection rates. Locknut secures setting from system vibrations. Can be used for inlet or discharge injection. Pressures to 4000 PSI and temperatures to 300° F. Brass construction with Viton® sealing materials. Inlet is 3/8” FPT. Outlet is 3/8” MPT. Chemical hose barb is 1/4”. Part No. * Flow Rate Max. Pressure SS 50580-10 1.0 GPM 4000 PSI SS 50580-20 2.0 GPM 4000 PSI SS 50580-30 3.0 GPM 4000 PSI SS 50580-40 4.0 GPM 4000 PSI SS 50580-50 5.0 GPM 4000 PSI SS 50580-60 6.0 GPM 4000 PSI * Based on 40 PSI Incoming Pressure

Port Flow Pressure Injection Part No. Size Range Range Ratio Net Ea. DM 113230 1-1/4” NPT .50 to 45 GPM 5 to 100 PSI 1:4000 to 1:333 $ 829.00 DM 113212 1-1/4” NPT .50 to 45 GPM 5 to 100 PSI 1:500 to 1:40 656.00 DM 113215 1-1/4” NPT .50 to 45 GPM 5 to 80 PSI 1:250 to 1:20 829.00 DM SCT Corrosive Transfer Kit, 20 to 45 GPM................................... 61.05

D

Net Ea. $ 64.85 64.85 64.85 64.85 64.85 64.85

Visit Our Web Site at http://www.dultmeier.com or E-Mail us at dultmeier@dultmeier.com

80 & 100 GPM Units Port Flow Pressure Injection Part No. Size Range Range Ratio Net Ea. DM 114151 2” Flange 20 to 100 GPM 20 to 120 PSI 1:1000 to 1:200 $ 1950.00 DM 114153 2” Flange 20 to 100 GPM 20 to 120 PSI 1:200 to 1:100 1950.00 Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0684


Chemical Injectors

108

Water Driven Chemical Injectors from Dema Engineering. Solutions are added into the water flow for accurate mixing and injection. Injection rates remain constant regardless of flow or pressure. Water driven design means no electricity is required. Pressure range from 3.0 to 120 PSI. MixRite Injectors are ideal for use with chemicals and fertilizers. Applications include car and truck wash, agriculture, greenhouses and industrial applications.

1

Bodies are either Nylon or Kynar (PVDF) construction. Kynar models feature PVDF bodies with Hastelloy springs and Extreme Viton® seals for aggressive chemicals that may contain acids. (CL) models feature nylon bodies with Hastelloy springs and Extreme Viton® seals for compatibility with corrosive chemicals. Models are shown with or without control valves that allow for the shut off of the chemical draw line while still allowing water flow through the unit.

Mai

4

2

nW ater

3

Fee

d

5

Main Water Pipe

Recommended Standard Installation: 1. Main Valve 2. Back flow preventer 3. Pressure regulator 4. Filter - 120 mesh (130 Micron Min.) 5. Pressure gauge 6. Anti siphon Valve 7. On/Off Ball Valve

Chemical Concentrate

D

D

572 / 573 Models

14CW05 / 1410 Models

D

D

Nylon Bodies (Aflas Seals) Part No. Valve Body Port Size Flow Range Injection Range Wt.

DE 569OF DE 570 DE 571 DE 572 DE 573 DE 1410A DE 1410M

Yes No Yes No Yes No Yes

Nylon Nylon Nylon Nylon Nylon Nylon Nylon

3/4” MPT 3/4” MPT 3/4” MPT 3/4” MPT 3/4” MPT 3/4” MPT 3/4” MPT

.9 to 11 GPM .9 to 11 GPM .9 to 11 GPM .9 to 11 GPM .9 to 11 GPM .9 to 14 GPM .9 to 14 GPM

1000:1 to 100:1 300:1 to 50:1 300:1 to 50:1 250:1 to 25:1 250:1 to 25:1 100:1 to 10:1 100:1 to 10:1

4 lbs. 4 lbs. 4 lbs. 4 lbs. 4 lbs. 4 lbs. 4 lbs.

Nylon Bodies (Viton® Seals) Part No. Valve Body Port Size Flow Range Injection Range

DE 569CL DE 570CL DE 571CL DE 572CL DE 573CL DE 14CW05 DE 574CL DE 575CL

Yes No Yes No Yes No No Yes

Nylon Nylon Nylon Nylon Nylon Nylon Nylon Nylon

3/4” MPT 3/4” MPT 3/4” MPT 3/4” MPT 3/4” MPT 3/4” MPT 3/4” MPT 3/4” MPT

.9 to 11 GPM .9 to 11 GPM .9 to 11 GPM .9 to 11 GPM .9 to 11 GPM .5 to 14 GPM .9 to 11 GPM .9 to 11 GPM

1000:1 to 100:1 300:1 to 50:1 300:1 to 50:1 250:1 to 25:1 250:1 to 25:1 100:1 to 20:1 33:1 to 10:1 33:1 to 10:1

Kynar Bodies (Viton® Seals) Part No. Valve Body Port Size Flow Range Injection Range

DE 569PV DE 570PV DE 571PV DE 572PV DE 573PV

Yes No Yes No Yes

Kynar Kynar Kynar Kynar Kynar

3/4” MPT 3/4” MPT 3/4” MPT 3/4” MPT 3/4” MPT

.9 to 11 GPM .9 to 11 GPM .9 to 11 GPM .9 to 11 GPM .9 to 11 GPM

1000:1 to 100:1 300:1 to 50:1 300:1 to 50:1 250:1 to 25:1 250:1 to 25:1

Net Ea.

$ 285.00 275.00 285.00 275.00 285.00 435.00 445.00

Wt.

Net Ea.

4 lbs. 4 lbs. 4 lbs. 4 lbs. 4 lbs. 4 lbs. 4 lbs. 4 lbs.

$ 425.00 415.00 425.00 414.00 424.00 344.00 529.00 539.00

Wt.

Net Ea.

4 lbs. 4 lbs. 4 lbs. 4 lbs. 4 lbs.

$ 469.00 459.00 469.00 459.00 469.00

CL for Corrosive Liquids

DE 576IN DE 577 DE 578IN DE 579 DE 574IN

Valve

Body

Port Size

Flow Range

Injection Range

Wt.

Net Ea.

No Yes No Yes No

Nylon Nylon Nylon Nylon Nylon

3/4” MPT 3/4” MPT 3/4” MPT 3/4” MPT 3/4” MPT

.9 to 11 GPM .9 to 11 GPM .9 to 11 GPM .9 to 11 GPM .9 to 11 GPM

500:1 to 50:1 500:1 to 50:1 250:1 to 25:1 250:1 to 25:1 33:1 to 10:1

4 lbs. 4 lbs. 4 lbs. 4 lbs. 4 lbs.

$ 365.00 375.00 363.00 375.00 429.00

KYNAR Models. Most Chemically Resistant

D

BYPASS Models - Nylon Bodies Bypass units are designed to keep aggressive chemicals out of the flow chamber while protecting internal parts. Part No.

Che Wa mical ter Mix 6 7

D

TF Series Units. Designed specifically for the Agriculture Industry for fertilizer injection. Bodies are nylon construction, seals are EPDM. TF10 & TF25 models come with support legs. Rated from 15 to 120 PSI.

Part No.

DE TF5-1 DE TF5-2 DE TF5-5 DE TF10-2 DE TF10-5 DE TF25-1 DE TF25-2 DE TF25-5

Port Size

Flow Range

1” MPT 1” MPT 1” MPT 1-1/2” MPT 1-1/2” MPT 2” MPT 2” MPT 2” MPT

1.0 to 22 GPM 1.0 to 22 GPM 1.0 to 22 GPM 2.0 to 45 GPM 2.0 to 45 GPM 9.0 to 110 GPM 9.0 to 110 GPM 9.0 to 110 GPM

DULTMEIER SALES

Injection Range

1:1000 to 1:100 1:500 to 1:50 1:100 to 1:20 1:500 to 1:50 1:100 to 1:20 1:1000 to 1:100 1:333 to 1:40 1:100 to 1:20

OMAHA, NE (800)

228-9666

Wt.

Net Ea.

13 lbs. 13 lbs. 13 lbs. 16 lbs. 16 lbs. 46 lbs. 46 lbs. 46 lbs.

$ 432.50 432.50 670.00 641.00 697.00 1471.00 1471.00 1622.00

DAVENPORT, IA (800)

553-6975

Models TF10 / TF25

Model TF5

Viton® is a registered trademark of DuPont Performance Elastomers

www.dultmeier.com

E0859


Chemical Injectors

109

DOSATRON Non-Electric, Self-Priming, Water Driven Chemical Injectors. Gives an accurate and uniform feeding of soaps, waxes or other chemicals into water lines!! Ideal for a wide variety of Car Wash, Industrial, Turf and Pest Control applications. Polyethylene or Delrin housings. Water Driven, Constant Output, Easy to Adjust ! Note: On Chemical use, always check Chemical Compatibility of Components before using.

• External Ratio Adjustment: Injection ratios can be easily changed with one external adjustment. • Easy to Use: No assembly required. Simple hookup can be completed without tools. • Minimal Operation Costs: Driven from existing water line pressure. • Low Maintenance: Yearly disassembly & seal replacement can be done in minutes.

• Highly Accurate: Set it and forget it!! Injectors compensate automatically for any change in water pressure. • Portability: Units can be permanently mounted or portable and setup in minutes. Ideal for spot feeding or fungicide drenching. • Self-Priming: Up to 13' Lift. • Rated to 104° F. • Bypass Models also available.

RECOMMENDED INSTALLATION Mixing Chamber

11 GPM

20 GPM

D D

Blended Solution

water flow

D Externally adjustable ratios

14 GPM D25

Intake from concentrate container

D45 Series

D14MZ2

OPERATING PRINCIPLE The injector is installed in-line. Incoming water (1) drives the piston (4) moving it up and down, pulling the concentrate (3) into the mixing chamber (5), accurately blending it with the water flow before passing through the outlet (2). Because of its volumetric design, the injector maintains a constant ratio of concentrate to water flow regardless of water pressure and flow.

Port Maximum Pressure Injection Injection Part No. Flow Rate Size Flow Range Range Ratio Percent Net Ea. DO D25RE1500VFII 11 GPM 3/4” MPT 0.05 to 11 GPM 4.3 to 85 PSI 1:1500 to 1:500 .07 to 0.2% $ 375.00 DO D14MZ5VVFII **11 GPM 3/4” MPT 0.05 to 11 GPM 4.3 to 85 PSI 1:200 to 1:20 0.5 to 5.0% 799.00 DO D14MZ10VVFII **11 GPM 3/4” MPT 0.00 to 11 GPM 4.3 to 85 PSI 1:500 to 1:66 0.2 to 1.5% 859.00 DO D14MZ5 14 GPM 3/4” MPT 0.05 to 14 GPM 4.3 to 85 PSI 1:200 to 1:20 0.5 to 5.0% 589.00 DO D14MZ10 14 GPM 3/4” MPT 0.05 to 14 GPM 4.3 to 85 PSI 1:100 to 1:10 1.0 to 10% 599.00 DO D14MZ2 14 GPM 3/4” MPT 0.05 to 14 GPM 4.3 to 85 PSI 1:500 to 1:50 0.2 to 2.0% 390.50 DO D45-3000 20 GPM 1” MPT 0.4 to 20 GPM 7 to 70 PSI 1:1000 to 1:3000 0.1 to .03% 759.00 DO D45RE15VII 20 GPM 1” MPT 0.4 to 20 GPM 7 to 70 PSI 1:500 to 1:66 0.2 to 1.5% 519.00 DO DSA45-3 20 GPM 1” MPT 0.4 to 20 GPM 7 to 70 PSI 1:200 to 1:33 0.5 to 3.0% 689.00 DO D8R 40 GPM 1-1/2” MPT 2.2 to 40 GPM 2 to 110 PSI 1:500 to 1:50 0.2 to 2.0% 868.00 DO D8RE5VFII 40 GPM 1-1/2” MPT 2.2 to 40 GPM 2 to 110 PSI 1:100 to 1:20 1.0 ti 5% 1349.00 ** Industrial Models for Viscous Chemicals.

Panel Units Water Driven, Non-Electric Chemical Dispensers. Can be used for a wide variety of chemicals including tire cleaner, presoak, foam brush, wheel cleaners, wax and protectants. Available in 1, 2 or 3 product systems. Units are mounted on aluminum bases for wall mounting.

D

Water drive design ensures that injection ratio is always the same. Fluctuations in water pressure to the systems does not affect chemical injection rates. 24-Volt or 110-Volt solenoids are only used to control the water flow to the dispensers. Note: We can build these systems to order with your choice of injector models. Part No.

Number of Products

Net Ea.

DO DO16P 1 $ 685.00 DO DO16P-2 2 685.00 DO DO16P-3 3 2024.00 DO DO16P-3F * 3 2104.00 * For Triple Foam in Automatics or Tunnels. DULTMEIER SALES

OMAHA, NE (800)

Model DO16P-3

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0103


Pressure Gauges

110

LOWER MOUNT

BACK MOUNT

Liquid-Filled - with Brass Stems -

Dry Design & Liquid Filled

D

Pressure Gauges D

D

D

Back Connection

Back Mount Gauges for those requirements where rear mount plumbing is required. These gauges are available with 1-1/2", 2" or 2-1/2" dial faces and in either Glycerin-filled or Dry design. All gauges feature brass MPT inlet stem. Cases are either painted steel or ABS plastic. DRY GAUGES Back Mount (BM) Part No. Max. PSI Fill Size Case Stem Net Ea. AH J504 15 Dry 1-1/2" Steel 1/8" $ 2.70 AH J505 30 Dry 1-1/2" Steel 1/8" 2.70 AH J507 60 Dry 1-1/2" Steel 1/8" 2.70 AH J508 100 Dry 1-1/2" Steel 1/8" 2.70 AH J518 160 Dry 1-1/2" Steel 1/8" 2.70 AH J509 300 Dry 1-1/2" Steel 1/8" 2.70 AH J511 30 Dry 2" Steel 1/4" 2.93 AH J512 60 Dry 2" Steel 1/4" 2.95 AH J513 100 Dry 2" Steel 1/4" 2.95 AH J516 300 Dry 2" Steel 1/4" 2.95 AH 2DP60 60 Dry 2-1/2" Steel 1/4" 3.66 AH 2DP100 100 Dry 2-1/2" Steel 1/4" 3.66 AH 2DP200 200 Dry 2-1/2" Steel 1/4" 3.66 10% Discount on 20 Assorted Gauges Viton® is a registered trademark of DuPont Performance Elastomers

Bottom Mount, Glycerin-Filled Pressure Gauges. The best choice where vibration or pulsation may be present. These gauges feature ABS Case (Ashcroft brand) or Stainless Case (Imported brand). Dial faces are either 2-1/2" or 4". Inlet stem is 1/4" MPT brass on all except WGGSS Series which feature stainless stems. Pressure range from 60 to 10,000 PSI. (Models *2640-15 & 16 are combination Vacuum/ Pressure Gauges that are lower mount). Part No. Maximum PSI Fill Size Case Brand Net Ea. AH 2640-9 60 Liquid 2-1/2" ABS Ashcroft $ 11.65 AH 2750-9 60 Liquid 2-1/2" Stainless Import 7.90 AH GG604 60 Liquid 4” Stainless Import 30.55 AH 2640-10 100 Liquid 2-1/2" ABS Ashcroft 11.65 AH 2750-10 100 Liquid 2-1/2" Stainless Import 7.90 AH GG1004 100 Liquid 4" Stainless Import 29.25 AH 2640-11 200 Liquid 2-1/2" ABS Ashcroft 11.65 AH 2750-11 200 Liquid 2-1/2" Stainless Import 7.90 AH 2750-8 600 Liquid 2-1/2" Stainless Import 7.90 AH 2640-1 1000 Liquid 2-1/2" Stainless Import 7.98 AH 2640-2 1500 Liquid 2-1/2" Stainless Import 7.98 AH 2640-3 2000 Liquid 2-1/2" ABS Ashcroft 14.60 AH 2750-3 2300 Liquid 2-1/2" Stainless Import 9.15 AH 2640-4 3000 Liquid 2-1/2" ABS Ashcroft 14.60 AH 2750-4 3600 Liquid 2-1/2" Stainless Import 9.15 AH 2640-5 5000 Liquid 2-1/2" ABS Ashcroft 14.60 AH 2750-5 6000 Liquid 2-1/2" Stainless Import 7.90 AH 2640-14 10,000 Liquid 2-1/2" Stainless Import 7.98 AH 2640-15 * 30 HG to 100# Liquid 2-1/2" Stainless Import 7.98 AH 2640-16 * 30 HG to 30# Liquid 2-1/2" Stainless Import 7.97 AH 2640-17 30 HG Only Liquid 2-1/2" Stainless Import 7.98 AH 2640-18 * 30 HG to 30# Liquid 4" Stainless Import 30.55 AH 2640-20 * † 30 HG to 60# Liquid 2.5” STainless Import 19.69 * Combo Vacuum/Pressure Gauge. † Stainless Stem Also

10% Discount on 20 Assorted Gauges.

LIQUID GAUGES Back Mount (BM) Part No. Max. PSI Fill Size Case Stem Net Ea. AH 2640-60 60 Liquid 2-1/2" Stainless 1/4" $ 7.90 AH 2640-65 100 Liquid 2-1/2" Stainless 1/4" 7.90 AH 2640-70 200 Liquid 2-1/2" Stainless 1/4" 7.90 AH 2640-6 300 Liquid 2-1/2" Stainless 1/4" 7.90 AH 2640-80 600 Liquid 2-1/2" Stainless 1/4" 7.90 AH 2640-85 1000 Liquid 2-1/2" Stainless 1/4" 7.90 AH 2640-90 2000 Liquid 2-1/2" Stainless 1/4" 7.90 AH 2640-95 3000 Liquid 2-1/2" Stainless 1/4" 7.90 AH 2640-50 5000 Liquid 2-1/2" Stainless 1/4" 7.90 AH 2640-25 10,000 Liquid 2-1/2" Stainless 1/4" 7.98 AH 26CL U Clamp for Back Mount Gauges................. 2.00 10% Discount on 20 Assorted Gauges

Stainless Steel Gauges Bottom Mount - SS Stem

Max. Part No. PSI

Designed to protect pressure gauges from corrosive chemicals. Available with 1/4" NPT (F) connections. Materials exposed to fluid system are Viton® and Acetal. Gauge side of dampener requires Glycerin or ATF fill. 300 PSI maximum working pressure. Part No.

Net Ea.

SS 22470 Gauge Isolator

$ 46.80

1/8" Gauge Tubing Connectors Part No.

Description

Net Ea.

SS 21545NY 1/8" Tube Nut (See A)................................... $ 1.05 SS 21486NY 1/8" Union (See B)....................................... 1.04 SS 21736NY 1/8"x3/16” Male Coupler + Tube Nut (See C) 2.45

B

C

Gauge Damper

B301A This "pulsation-check" prolongs gauge life when placed between control valve & pressure gauge. 150 PSI rating. Part No. Net Ea. TW B301A Plated Steel Pulsation Check 1/4" FPT x 1/4" MPT Connection.......................................... $ 9.81 OMAHA, NE (800)

228-9666

Case

Brand

Net Ea.

Lower Mount Gauges Dry Pressure Gauges, Bottom Mount, are economically priced and recommended for use where vibrations, pulsations and hydraulic shock are minimal. Cases are ABS plastic or steel. Dial faces are 2", 2-1/2" or 4". Brass inlet stem is 1/4" MPT. Pressure range from 15 to 1,000 PSI. Gauges shown are import brand. Part No.

A

GAUGE ACCESSORIES

DULTMEIER SALES

Size

Dry Design

Gauge Isolator & Protector

Model 22470

Fill

AH WGGSS60 60 Liquid 2-1/2" Stainless Ashcroft $ 19.80 AH WGGSS100 100 Liquid 2-1/2" Stainless Ashcroft 19.80 AH WGGSS200 200 Liquid 2-1/2" Stainless Ashcroft 19.80 AH WGGSS400 400 Liquid 2-1/2" Stainless Ashcroft 19.80 10% Discount on 20 Assorted Gauges on (1) Order

Liquid Filled

D

LIQUID-FILLED

D

Max. PSI

Fill

Size

Case

D

Net Ea.

AH J500 15 Dry 2" ABS $ 2.75 AH J501 30 Dry 2" ABS 2.75 AH J502 60 Dry 2" ABS 2.76 AH J503 100 Dry 2" ABS 2.76 AH J506 300 Dry 2" ABS 2.76 AH 1DP60 60 Dry 2-1/2" ABS 3.43 AH 1DP100 100 Dry 2-1/2" ABS 3.43 AH 1DP160 160 Dry 2-1/2" ABS 3.43 AH 1DP200 200 Dry 2-1/2" ABS 3.45 AH SG400 400 Dry 2-1/2" ABS 3.45 AH SG600 600 Dry 2-1/2" ABS 3.45 AH SG1000 1000 Dry 2-1/2" ABS 3.45 AH SG60-4 60 Dry 4" Steel Case 7.14 AH SG100-4 100 Dry 4" Steel Case 7.13 10% Discount on 20 Assorted Gauges DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0080


Flow Meters

111

Flowmeters D

D D

Straight FPT

BACK MOUNT Flowmeters

Injection Molded Flow Meters from Blue White. Standard features: Chemically resistant, one-piece, Polysulfone meter bodies • Viton® o-ring seals • 316 stainless steel float and float guide • Rated to 150 psi • Permanent screen printed scales show gallons per minute & Liters per minute or gallons per hour for calibration.

Injection Molded Flowmeters

Elbow

Straight MPT

Calibration Part No. GPM LPM Ports Length BL F44250LH6 .025 - .250 0.1 -1.0 3/8" MPT 6-3/16" BL F44375LH6 0.1 - 1.0 0.4 - 4.0 3/8" MPT 6-3/16" BL F44376LH6 0.2 - 2.0 0.75 - 7.5 3/8" MPT 6-3/16" BL F44500LH6 0.5 - 5.0 1.8 - 18.0 3/8" MPT 6-3/16" BL F44750LH12 1.0 - 10.0 5.0 - 37.5 3/4" MPT 7-1/2" BL F40375LN6 0.1 - 1.0 0.4 - 4.0 3/8" FPT 8-3/16" BL F40376LN6 0.2 - 2.0 1.0 - 7.5 3/8" FPT 8-3/16" BL F40500LN6 0.5 - 5.0 1.8 - 18 3/8" FPT 8-3/16" BL F40750LN12 1.0 - 10 4.0 - 38 3/4" FPT 11" BL F41017LN12 1.0 - 17 - 3/4" FPT 11" BL F44250LHE8 .025 - .250 0.1 - 1.0 1/2" MPT elbow 7-1/8" BL F44375LHE8 0.1 - 1.0 0.4 - 4.0 1/2" MPT elbow 7-1/8" BL F44376LHE8 0.2 - 2.0 0.75 - 7.5 1/2" MPT elbow 7-1/8" BL F44500LHE8 0.5 - 5.0 1.8 - 18.0 1/2" MPT elbow 7-1/8" BL F44750LHE12 1.0 - 10.0 5.0 - 37.5 3/4" MPT elbow 8-1/8" Calibration BL-NO GPH Ports Length BL F44330LH8 3.0 - 30.0 1/2" MPT straight 6-3/16" BL F44330LHE8 3.0 - 30.0 1/2" MPT elbow 7-1/8"

Net Ea $ 70.15 70.15 70.15 70.15 80.95 73.70 73.70 73.70 139.00 139.00 79.30 84.95 84.95 84.95 98.60 Net Ea. $ 70.15 83.95

Visi-Flo Flowmeters Dwyer Flow Meters are designed to register or regulate flow rates of liquid products • All models feature acrylic plastic bodies • Maximum pressure rating is 100 PSI • All models feature metal mounting inserts tapped with 10/32" thread • Temperatures to 120° F.

DR VFABV-41 DR VFABV-42 DR VFA-41 DR VFA-42 DR VFASSV-41 DR VFASSV-42 DR VFBSSV80 DR VFBSSV83 DR VFBSSV81 DR VFC-141 DR VFC-142 DR VFC-143

Metering Wetted Valve Parts

Yes Yes No No Yes Yes Yes Yes Yes No No No

Brass Brass Brass Brass Stainless Stainless Stainless Stainless Stainless PVC PVC PVC

DULTMEIER SALES

• R.O. & D.I. Water Systems • Pollution Treatment Equipment • Purging & Regulating Equipment • Water & Wastewater Treatment Equipment • Film & X-Ray Processing • Chemigation Equipment

Features: • Tough Machined Acrylic Meter Body • Stainless Steel Internal Parts • Permanent Screen Printed Scales • Calibrations in GPM, LPM & SCFM • Optional Integral Flow Adjustment Valve

Valve

No No No No No

Part No. D

Flow Range

.6 to 5 GPH 2 to 10 GPH .6 to 5 GPH 2 to 10 GPH .6 to 5 GPH 2 to 10 GPH .5 to 12 GPH 1 to 20 GPH 6 to 60 GPH .5 to 5 GPM 1 to 10 GPM 2 to 20 GPM

OMAHA, NE (800)

D

F500 for Panel Mount

F550A with Adjustment Valve

BL F55250L BL F55250LA BL F55375L BL F55375LA BL F55376L BL F55376LA BL F55500L BL F55500LA BL F55750L

Calibration

Ports

Net Ea.

1.0 - 11 GPH .2 - 1.2 GPM 12 - 72 GPH .3 - 3.0 oz/min. 2.0 - 20 oz/hr.

1/4” MPT 1/4” MPT 1/4” MPT 1/8” MPT 1/8” MPT

$ 49.50 54.50 54.50 54.50 54.50

Valve

Calibration GPM LPM

Ports

Net Ea

No Yes No Yes No Yes No Yes No

.025 - .250 0.1 - 1.0 .025 - .250 0.1 - 1.0 0.1 - 1.0 0.4 - 4.0 0.1 - 1.0 0.4 - 4.0 0.2 - 2.0 0.75 - 7.5 0.2 - 2.0 0.75 - 7.5 0.5 - 5.0 1.8 - 18 0.5 - 5.0 1.8 - 18 2.0 - 10 8.0 - 38

1/4" MPT 1/4" MPT 3/8" MPT 3/8" MPT 3/8" MPT 3/8" MPT 1/2" MPT 1/2" MPT 3/4" MPT

$ 86.35 127.50 83.95 117.00 83.95 117.00 83.95 117.00 99.10

Calibration Part No. Valve SCFM (Air)

Net Ea.

$ 41.45 41.45 31.75 31.75 54.95 54.95 77.75 77.75 77.75 88.95 88.95 88.95

228-9666

D

All flow meters are constructed of high quality solid acrylic meter bodies with stainless steel internals and permanent screen printed scales. Calibrations in GPM/LPM or SCFM. Available with or without adjustment valves. Can be mounted direct or panel mounted. Temperatures to 120° F. and pressures to 150 PSI on F500 Series. Temperatures to 200° F. and 250 PSI on F550 Series.

BL F505E BL F507E BL F508E BL F513E BL F515E

VFC Models: Flow meter only • Scale is 5" and overall height is 10" • Width is 1-5/8" • Flow ranges are (.5 to 5), (1.0 to 10) or (2.0 to 20) gallons per minute • Standard with 1" FPT ports and Buna-N O-rings • Accuracy to (+ or -) 2%. Part No.

Applications:

Part No.

VFA Models: Available with either brass or stainless steel metering valves • Scale is 2" and overall height is 4" • Width is 1" • Flow ranges are (.6 to 5.0) or (2.0 to 10) gallons per hour • Standard with 1/8" FPT ports and Buna-N O-rings • Accuracy to (+ or -) 5%. VFB Models: Scale is 4" and overall height is 6-1/2" • Width is 1-3/8" • Flow ranges are (.5 to 12), (1.0 to 20) or (6 to 60) gallons per hour • Standard with 1/8" FPT ports and Buna-N O-rings • Accuracy to (+ or -) 3 %.

Blue-White Flowmeters for accurate control of liquids or air. Ideal for use on RO Systems, Soap or Wax Lines, Pollution Treatment Equipment, Film Processing Systems, Chemigation Units, etc.

BL F55250G BL F55250GA BL F55375G BL F55375GA BL F55376G BL F55376GA BL F55500G BL F55500GA

No Yes No Yes No Yes No Yes

0.15 - 1.0 0.15 - 1.0 0.5 - 4.0 0.5 - 4.0 1.0 - 7.0 1.0 - 7.0 2.0 - 20 2.0 - 20

Ports

Net Ea.

1/4" MPT 1/4" MPT 3/8" MPT 3/8" MPT 3/8" MPT 3/8" MPT 1/2" MPT 1/2" MPT

$ 86.35 127.00 84.00 117.00 84.00 117.00 83.95 117.00

Viton® is a registered trademark of DuPont Performance Elastomers

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0065


Rotor Arms & Swivels

112

Stainless Steel Rotor Arms Stainless Rotor Arms are an ideal choice for tank cleaners, parts washers, wheel blasters, surface cleaners and many other industrial applications. Laser welded and balanced with preset angles to ensure quality performance. Available in 2, 3 or 4 arm and 2 to 5 nozzles to meet your needs. Rotors will accept 1/8” or 1/4” nozzles as noted. Nozzles are not included. Rated for pressures to 4000 PSI and temperatures to 250° F. Note: G3/8” F inlet is designed to match up to Mosmatic Swivels with G3/8” M Threads.

Four Nozzle Three Nozzle

Two Nozzle

TKA-2w2 (for Part No. 1/4” Ports MM 82707 MM 82708 MM 82709 MM 82710 MM 82711 MM 82712 MM 82713 MM 82714 MM 82715

two nozzles) Part No. 1/8” Ports Diameter MM 82807 8” MM 82808 10” MM 82809 12” MM 82810 14” CALL MM 82811 16” for MM 82812 18” PRICING MM 82813 20” MM 82814 22” MM 82815 24”

TKA-3w3 (for Part No. 1/4” Ports MM 82767 MM 82768 MM 82769 MM 82770 MM 82771 MM 82772 MM 82773 MM 82774 MM 82775

three nozzles) Part No. 1/8” Ports Diameter MM 82867 8” MM 82868 10” MM 82869 12” MM 82870 14” CALL MM 82871 16” for MM 82872 18” PRICING MM 82873 20” MM 82874 22” MM 82875 24”

TKA-4w4 (for Part No. 1/4” Ports MM 82954 MM 82731 MM 82733 MM 82737 MM 82742 MM 82743

four nozzles) Part No. 1/8” Ports N/A MM 82831 MM 82833 MM 82837 MM 82842 MM 82843

Diameter 4” / 4” 8” / 8” CALL 14” / 8” for 16” / 10” PRICING 18.5” / 14” 20” / 14”

Flanged Style

Rotor Arm Swivels Mosmatic Swivels are designed for use with stainless steel rotor arms shown above. Can be used with surface cleaners, parts washers, wheelblasters, etc. A wide variety of mounting options are available. All models are available with either 1/4” or 3/8” FPT inlet and G3/8” M outlet. Rated to 4000 or 5000 PSI as noted. Rated up to 2000 RPM and temperatures to 250° F. DYT and DYCI swivels are all stainless steel construction. DYF, DYG and DYL swivels feature stainless internals with nickel-plated brass bodies.

High Pressure Swivels High quality, Flanged Style Swivels for surface cleaners, tire applicators, under carriage wash, etc. Brass, Nickel-plated construction. Standard with Carbide seals rated to 250° F.

D

DYCI

DYT

Max. Max. Maximum Part No. Ports PSI RPM Temperature

All Stainless

DYT

Part No. MM 59063 MM 59163

Inlet

Outlet

1/4” NPTF 3/8” NPTF

G3/8” M G3/8” M

DYCI

Part No. MM 55063 MM 55163

Inlet Outlet

1/4” NPTF 3/8” NPTF

G3/8” M G3/8” M

Part No. MM 58063 MM 58163 DYG

Part No. MM 57063 MM 57163 DYL

Part No. MM 56063 MM 56163

5000 5000

2000 2000

Max. Max. PSI RPM

5000 5000

Brass/Nickel Inlet

Outlet

1/4” NPTF 3/8” NPTF

G3/8” M G3/8” M

Inlet Outlet

1/4” NPTF 3/8” NPTF

G3/8” M G3/8” M

Inlet Outlet

1/4” NPTF 3/8” NPTF

G3/8” M G3/8” M

CALL for PRICING

MM 58051 MM 58153

1/4" F x 1/4" M 3/8" F x 3/8" M

4000 2000 4000 2000

250° F. 250° F.

MM 38051 MM 38153

1/4" F x 1/4" M 3/8" F x 3/8" M

2000 2000 2000 2000

250° F. 250° F.

High Pressure Swivels DYL

Max. Max. PSI RPM

4000 4000

4000 4000

D

2000 2000

CALL for PRICING

Max. Max. PSI RPM

4000 4000

High quality, Bulkhead Swivels for surface cleaners, tire applicators, under carriage wash, etc. Brass, Nickel-plated construction. 37 Series is standard with Ceramic seals. 57 Series is standard with Carbide seals.

2000 2000

Max. Max. PSI RPM

2000 2000

DULTMEIER SALES • OMAHA, NE

CALL for PRICING

Bulkhead Style

2000 2000

DYG

DYF

DYF

Max. Max. PSI RPM

(800) 228-9666

Part No. Ports

Max. Max. Maximum PSI RPM Temperature

MM 33051 MM 33153 MM 37051 MM 37153 MM 57051 MM 57153

4000 4000 2500 2500 4000 4000

1/4" F x 1/4" M 3/8" F x 3/8" M 1/4" F x 1/4" M 3/8" F x 3/8" M 1/4" F x 1/4" M 3/8" F x 3/8" M

www.dultmeier.com

• DAVENPORT, IA

1000 1000 2000 2000 2000 2000

(800) 553-6975

100° F. 100° F. 250° F. 250° F. 250° F. 250° F.

CALL for PRICING

E0862


Spinners • Tire Cleaners • Rotor Arm Swivels

113

Stablilizer Spinners High Pressure Stabilizer Spinners are ideal for use in Car/Truck Wash Applications as well as a wide variety of Industrial cleaning needs. High quality, Swiss engineering. Designed to project a precise spray pattern for exceptional cleaning. Stabilizers keep water flow in a tight pattern for more effective performance than that of turbo nozzles or conventional nozzles. Swiss, stainless steel construction is standard on every piece except the swivels which are nickel-plated brass. Each system is assembled to meet your specific needs. Specify 1/4” or 3/8” straight or 90 degree swivel, four rotor arm, and insert nozzles matched to flow rate and pressure of your application. Completed assembly will include swivel, rotor arm, nozzle inserts and stabilizer nozzles with adapters. For existing rotor arms already in use, stabilizers, inserts and adapters can also be used to convert your system to stabilizer design. (1/8” or 1/4” are available for conversions). Part No.

MM 14901 MM 14902 MM 0002EG MM 0003EG MM 0004EG

Stabilizer Nozzle with 1/4” Adapter................ Stabilizer Nozzle with 1/8” Adapter................ CALL #2 Nozzle Insert............................................. for #3 Nozzle Insert............................................. PRICING #4 Nozzle Insert.............................................

four nozzles) Part No. 1/8” Ports N/A MM 82831 MM 82833 MM 82837 MM 82842 MM 82843

High Flow High or Low Pressure Self Rotating Quadruple Bearing System Stainless Steel Construction • Maintenance Free • Longevity • Ports are 1/4” or 3/8” FPT

Part No. MM 59063 MM 59163

Inlet

Outlet

1/4” NPTF 3/8” NPTF

G3/8” M G3/8” M

DYCI

Part No. MM 55063 MM 55163

Inlet Outlet

1/4” NPTF 3/8” NPTF

G3/8” M G3/8” M

1/8" NPT Female

Stainless pans are 21" diameter. Arms are designed to hold (4) 1/8" MPT nozzles, (not included). No. 83282 outside arm coverage is 16", inside arm coverage is 10". No. 84514 outside arm coverage is 18-1/2", inside arm coverage is 14”. Both are rated to 4000 PSI, 2000 rpm and 200° F. Inlet fitting is 3/8" FPT.

Female

Max. Max. PSI RPM

5000 5000

2000 2000

Max. Max. PSI RPM

5000 5000

Adjustable Height

All Stainless

CALL for PRICING

2000 2000

3.937" 5.512"

DYG

DYF

14901 Shown

Rotor Arm (self-rotating)

Compact and lightweight for ease of installation. Mounting bracket is adjustable for different heights.

D

DYT

82954 Shown

Stainless steel, self-rotating units for use in cleaning Tires, Rocker Panels, Touchless systems, etc. Designed with stainless steel bearings for constant, easy turning. Simply feed these units from your high pressure pump unit and create a high pressure, spinning, cleaning unit. Designed to bolt to floor or rail.

DYCI

D

Inserts matched to your flow 0002EG / 0003EG / 0004EG

Tire Cleaner Applicators

Rotor Arm Swivels Mosmatic Swivels are designed for use with stainless steel rotor arms shown above. Can be used with surface cleaners, parts washers, wheelblasters, etc. A wide variety of mounting options are available. All models are available with either 1/4” or 3/8” FPT inlet and G3/8” M outlet. Rated to 4000 or 5000 PSI as noted. Rated up to 2000 RPM and temperatures to 250° F. DYT and DYCI swivels are all stainless steel construction. DYF, DYG and DYL swivels feature stainless internals with nickel-plated brass bodies. DYT

Stabilizer Nozzle Insert Nozzle Adapter

Mounting Screws

(1) Swivel, 90° or Straight (1) Rotor Arm, Specify Size (4) Stabilizer Nozzles (4) Insert Nozzles Matched to Your Flow

Four Nozzle

w Flo

D

Requires:

Diameter 4” / 4” 8” / 8” 14” / 8” 16” / 10” 18.5” / 14” 20” / 14”

w Flo

• • • • •

DYT Series Shown 1/4” or 3/8” FPT

Stainless Steel Rotor Arms TKA-4w4 (for Part No. 1/4” Ports MM 82954 MM 82731 MM 82733 MM 82737 MM 82742 MM 82743

Features:

DYL

D

D

D

Outside Arms

DYF

Part No. MM 58063 MM 58163 DYG

Part No. MM 57063 MM 57163 DYL

Part No. MM 56063 MM 56163

Brass/Nickel Inlet

Outlet

1/4” NPTF 3/8” NPTF

G3/8” M G3/8” M

Inlet Outlet

1/4” NPTF 3/8” NPTF

G3/8” M G3/8” M

Inlet Outlet

1/4” NPTF 3/8” NPTF

G3/8” M G3/8” M

Max. Max. PSI RPM

4000 4000

2000 2000

Max. Max. PSI RPM

4000 4000

2000 2000

Inside Arms

CALL for PRICING

Max. Max. PSI RPM

4000 4000

Part No.

MM 84504 MM 84514

2000 2000

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

D

D

Wt.

16" 4-Nozzle TCA Applicator Unit 11 lbs. 18-1/2" 4-Nozzle TCA Applicator Unit 12 lbs.

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

CALL for PRICING

E0915


90° SWIVELS Custom 90° Swivels Custom Designed 90° Swivels from Super Swivels. These units are designed for specific manufacturers of Automatic Car Washes. Rated from 1500 to 2000 psi.

No. 23152

D

D D

No. 23113 No. 24074 & 24073

Part No.

Fits Mfg. Inlet Outlet

SE 23152 Mark VII 1/2” MPT SE 23113 Hydrospray 1/2” MPT SE 24074 Hydrospray 1/2” MPT SE 24073 Hydrospray 3/4” MPT

1/2” FPT 1/2” FPT 1/2” FPT 3/4” FPT

Max. Max. RPM PSI

70 70 100 100

Net Ea.

1500 $ 159.00 1500 144.50 2000 165.00 2000 165.00

90° Swivels

DGE Series feature Nickel-Plated Brass bodies, one bearing design. Rated to 4000 PSI and 180° F. Maximum of 30 RPM. WDR Series feature Stainless Steel bodies, two Bearing design. Rated to 3000 PSI and 180° F. RPM varies with size.

D

D

DGE MxF

Part No.

Ports

1/2" M x F 1/2" F x F 3/4" M x F 3/4" F x F 1" M x F 1" F x F 1-1/4" M x F 1-1/4" F x F 1-1/2" M x F 1-1/2” F x F

WDR Series Part No.

MM 41261 MM 41361 MM 41362 MM 41461 MM 41462

- OEM Replacement Swivels for Popular Automatic Carwashes -

Brand

Swivel

D&S 5000

Mosmatic #

3/8” NPT MxF & 90˚ Swivel Jim Coleman 4000 psi

MM 43262

Hydro Spray Rainmaker & Oasis

1/2” NPT MxF 90˚ Swivel 3000 psi

MM 41261

Mark VII 1/2” NPT MxF Aqua Jet Gear Driven (Old) Swivel 3000 psi

MM 41920

N/S 3/4” NPT F MM 59902 Quadra xG3/8”M Spinner 90˚ Swivel 2500 psi 3/4” FPT x 1-1/6” UNS 2000 psi

MM 40936

PDQ Laserwash & Wash World

1” NPT FxF Straight Swivel 3000 psi

MM 34927

1” NPT FxF 90˚ Swivel 3000 psi

MM 34885

POWERAIN

3/8” NPT F x 1/2” NPTM Swivel

MM 40932

Southern Pride Turbo Wash

3/4” NPT MxF 90˚ Swivel 3000 psi

MM 41361

Popular Brands

1/2” MxF 90˚ Swivel 200 RPM 4000 psi

MM 43363

RYKO

3/8” NPT F x G3/8” M 4000 psi

MM 58163

Magic Wand

3/8” NPT F x 3/4” MPT M 4000 psi Straight Swivel

MM 34854

WDR FxF

DGE Series MM 34873 MM 34883 MM 34874 MM 34884 MM 34875 MM 34885 MM 34876 MM 34886 MM 34877 MM 34887

Conversion Chart Automatic Car Wash Swivel Application

PDQ G5

Mosmatic 90 Swivels featuring Swiss Engineering are designed for the rigors of high flow water applications. Ideal for use with high pressure automatics, hose reels, sewer cleaners, etc. Rated to water pressures up to 4000 PSI and compressed air to 290 PSI.

114

Construction

Max RPM

Nickel-Plated Brass Nickel-Plated Brass Nickel-Plated Brass Nickel-Plated Brass Nickel-Plated Brass Nickel-Plated Brass Nickel-Plated Brass Nickel-Plated Brass Nickel-Plated Brass Nickel-Plated Brass

30 30 30 30 CALL 30 for 30 PRICING 30 30 30 30

Ports

Construction

Max RPM

1/2" M x F 3/4" M x F 3/4" F x F 1" M x F 1" F x F

Stainless Steel Stainless Steel Stainless Steel Stainless Steel Stainless Steel

150 130 130 110 110

DULTMEIER SALES • OMAHA, NE

CALL for PRICING

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0701


115

90° Swivels • Undercarriage Cleaning 90° Swivels

90 Degree Swivels

Ideal selection for use as replacement swivels on Automatic Car washes or Hose Reels. Can also be used for ceiling booms. “Live” swivel ball bearing design. Rebuildable. Grease zerk is standard. Superior quality Nickel-plated alloy steel. (Stainless steel construction where noted). Maximum temperature is 400° F. Ideal for use with hot water, steam, hydraulic fluid, etc. Retrofits to such popular brands as “Deublin” “Parker Hannifan”, “Aeroquip”, etc. D

(For Straight design SuperSwivels see adjoining page).

Inlet Outlet Max. Max. Part No. Port Port PSI RPM Net Ea. SE 9SS83AL 3/8" FPT 3/8" FPT 5000 10 $ 39.95 SE 9SS83AL-M 3/8" MPT 3/8" FPT 5000 10 40.05 SE 9SS81AL 1/2" FPT 1/2" FPT 5000 10 39.95 SE 9SS81AL-M 1/2" MPT 1/2" FPT 5000 10 31.80 SE 7153 1/2" MPT 1/2" FPT 5000 30 48.50 SE 9SS12AL 3/4" FPT 3/4" FPT 4500 10 56.55 SE 9SS12AL-M 3/4" MPT 3/4" FPT 4500 10 56.70 SE 24055 **3/4" MPT (SS) 3/4" FPT 3000 10 144.00 SE 25023 *1" FPT 1" FPT 4000 20 72.95 SE 25010 ▲ 1" FPT (SS) 1" FPT 1000 30 205.00 SE 9SS16AL-M 1" MPT 1" FPT 4000 10 69.70 SE 7390 **1" MPT (SS) 1" FPT 3000 10 205.00 SE 9SS20AL 1-1/4" FPT 1-1/4" FPT 4000 10 114.50 SE 9SS20AL-M 1-1/4” MPT 1-1/4” FPT 4000 10 91.95 SE 9SS24AL 1-1/2" FPT 1-1/2" FPT 3000 10 209.00 SE 9SS24AL-M 1-1/2" MPT 1-1/2" FPT 3000 10 209.00 SE SS8KIT-AL Repair Kit, 3/8" & 1/2"................................ 7.91 SE SS12KIT-AL Repair Kit, 3/4", old style............................ 7.69 SE 20183 Repair Kit, 3/4", new style.......................... 15.50 SE 20258 Repair Kit, 16015/25023............................ 12.95 SE SS16KIT-AL Repair Kit, 9SS16AL-M/7390..................... 11.50 SE 7380KIT Repair Kit for 7153 Swivel.......................... 14.50

Male x Female Part No. Size PA PS6901 3/8” M x F PA PS8901 1/2” M x F PA PS12901 3/4” M x F PA PS12901V 3/4” M x F PA PS16901 1” M x F PA PS16901V 1” M x F

TRU-TURN 90° Swivels Super Precision Roller Bearing Swivels for tough applications likeTouchless Automatics or high pressure hose reels. These severe-duty swivels are rebuildable and have been field tested for 12 months without failure.

Seal Buna Buna Buna Viton® Buna Viton®

Max. PSI 5000 5000 5000 5000 5000 5000

Net Ea. $ 47.90 50.90 67.35 70.65 80.10 85.70

Female x Female Part No. Size Seal PA PS6902 3/8” F x F Buna PA PS8902 1/2” F x F Buna PA PS8902V 1/2” F x F Viton® PA PS12902 3/4” F x F Buna PA PS16902 1” F x F Buna PA PS16902V 1” F x F Viton® PA PS24902 * 1-1/2” F x F Buna * 3-Piece design on 1-1/2” sizes.

Max. PSI 5000 5000 5000 5000 5000 5000 4000

Net Ea. $ 58.05 53.10 65.65 78.25 80.10 92.15 554.00

Undercarriage Cleaning System

D

Complete Undercarriage Cleaning Unit from Mosmatic.The perfect choice for car and truck wash operations. Compact design for easy installation in floors. Can be used for tunnels, self-serve, automatics, truck washes or fleet cleaning requirements. Heavy-duty, stainless steel construction.

Bodies are Stainless or Brass. All wetted parts are stainless steel. Flow rates to 45 GPM on 1/2" & 3/4" and 65 GPM on 1". Maximum pressure is 4,000 PSI. Max. Part No. Inlet Port Outlet Port PSI FL SW580 1/2" MPT 1/2" FPT 4000 FL SW580SS 1/2" MPT 1/2" FPT 4000 FL SW580ASS 1/2" MPT 3/4" FPT 4000 FL SW580C 3/4" MPT 3/4" FPT 4000 FL SW580C-SS 3/4" MPT 3/4" FPT 4000 FL SW580E 1" FPT 1" FPT 4000

Standard Features: Sealed bearings and hardened bearing races for extended service life • Full flow design • Buna or Viton® seals • Teflon backup rings • (Chromium-6 Free) Plated carbon steel construction for added corrosion resistance • Rated to 5000 PSI and 250° F. (Up to 1” sizes) • Available in M x F or F x F NPT ports • Many other port options are available.

D

NOTE: Kits includes seals, ball bearings, lock washer and zerk. * Double Bearing Design, Plated ▲ Double Bearing, 304SS Construction. ** Stainless steel construction.

All models feature grease zerks for routine lubrication. 90 de­gree design easily fits most booms or trol­leys. A very good option to other swivels on the market such as Deublin or Aeroquip.

PARKER PS Series 90 Degree Swivels are designed to eliminate hose twist and torque that may cause premature hose failure. Ideal for hose reels, wash booms and industrial applications.

Body Brass Stainless Stainless Brass Stainless Brass

System Includes: Stainless floor box • Stainless cover lid • Stainless high pressure swivels • Stainless water manifold • Stainless stabilizer nozzles designed for maximum coverage and high impact cleaning.

Net Ea. $ 215.00 191.50 206.00 217.00 215.00 213.00

Box dimensions are 29-1/2” Long x 12” Wide. Cover plate is 29-1/2” Long x 16” Wide. Box has 3/4” FPT inlet to feed water manifold and 1” FPT outlet for drain. Rated to 4000 PSI & 250° F. Note: EG Nozzle Inserts are not included and will be supplied to match existing pump

SERVICE & REPAIRS Did you know? We can service almost every brand of pump we sell in our catalog.

D

flow and pressure).

Call us at 1-800-228-9666 (Omaha, NE) for a quote!

Part No.

Wt.

MM 80640 Undercarriage Wash Unit

Net Ea.

77 lbs. $ 1298.00

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0910


BOOM & HOSE REEL SWIVELS 90° Boom Swivels

Boom Swivel 90° Boom Swivel from Parker. Ideal for use with self-serve ceiling booms. Pressure balanced, forged carbon steel body with Nickel plating. Rated to 3000 PSI and 250°F. 360 degree design eliminates torque twist and stress. Repairable design. EPDM seal is standard.

No. 40021 D

D

No. 40028

Inlet

Outlet

PSI

Stem

PA S2107V-38

3000 PSI

Net Ea.

$ 25.95

90° Boom Swivel From Spraying Systems a Boom Swivel that is designed for the rigors of ceiling booms used in the Car Wash Industry. Pressure loading of swivel is balanced so that it will swivel easily at all pressures up to 2000 PSI. Rated to temperatures up to 200° F. Nickel-plated brass construction with Buna o-rings and Delrin bearings. Ports are 3/8" MPT and 3/8" FPT. D

Maximum Part No. Pressure

Right Angle Hose Reel Swivel. Heavy duty design. Ideal for use as a replacement swivel on a wide variety of hose reel applications. Brass construction. Easily rebuildable. Ports are 1/2" FPT x 1/2" FPT. Rated to 3000 PSI. Viton® O-rings and Teflon washer are standard. Maximum temperature is 300° F.

90° Boom Swivels Perfect for use as a replacement swivel on ceiling booms. Use wherever hose moves or twists. Low torque design for easy movement. Sealed against dust for long life. Swivel action is 360°. Available in either brass or stainless steel construction. Ports are 3/8" MPT x 3/8" FPT. Standard with Buna-N o-rings. Maximum temperature is 200° F.

D

Net Ea. $ 27.00 10.90

Part No. Construction

Maximum Pressure

Net Ea.

90° Boom Swivels

Hose Reel Swivels from Super Swivels. Common replacement swivels used by many of the major hose reel manufacturers. Ball bearing, 90 degree design. Nickel-Plated steel with Viton® seal. Rebuildable. Rated to 400° F. Pressure vary as shown. Ports are FPT x FPT.

Solid brass body with precision stainless steel thrust bearings to swivel effortlessly at full rated pressure. Internally lubricated o-rings and polished 303 stainless steel spool piece assures long, trouble-free operation. An excellent replacement swivel for hose reels and overhead booms.

D

Max. Part No. Ports PSI FL SW504A-L 3/8" M x 3/8" F 3500 FL SW504A-LFF 3/8" F x 3/8" F 3500

Max. Part No. Size PSI Net Ea. SE 5023 1/2” FPT 5000 $ 39.95 SE 5033 3/4” FPT 4000 55.95 SE 5043 1” FPT 4000 69.95 SE 5053 1-1/4” FPT 4000 115.00 SE 5063 1-1/2” FPT 3000 196.50 SE SS8KIT Repair Kit, 3/8” & 1/2”..... 7.90 SE SS12KIT Repair Kit, 3/4”................ 8.10 SE SS16KIT Repair Kit, 1”................... 11.50

Stainless Stem

D

990-3/8

Brass Body

Net Ea. $ 28.70 31.95

Right Angle Boom Swivels Designed to swivel at 1500 PSI. No ball bearings to gall or rust. All Brass Body with Stainless Steel stem. Bronze thrust bearing for longer life. Buna-N seals are standard. Swivels are repairable. Available threaded 3/8" MPT x 3/8” FPT or 3/8” FPT x 3/8” FPT.

Maximum Part No. Pipe Thread Ports Pressure

D

990-3/8F

Net Ea.

SM 990-3/8 3/8" FPT X 3/8" MPT 1500 PSI $ 21.80 SM 990-3/8F 3/8" FPT x 3/8" FPT 1500 PSI 24.30 SM 990RK Repair Kit ............................................ 4.11

Viton® is a registered trademark of DuPont Performance Elastomers

(800) 228-9666

D

AA 7030 Brass 3000 PSI $ 23.00 AA 7035 Stainless 5000 PSI 29.80 AA 7030K Repair Kit .................................. 11.25

Hose Reel Swivels

DULTMEIER SALES • OMAHA, NE

Net Ea.

SS 36560-3/8 2000 PSI $ 27.95 SS AB36560KIT Repair Kit 2.96

Hose Reel Swivel

D

3/8” M x F

RPM

MM 40021 1/4" M 1/4" F 2200 Short 30 MM 40022 3/8" M 1/4" F 2200 Short 30 MM 40032 3/8" M 3/8" F 2200 Short 30 CALL MM 40028 1/4" M 1/4" F 2200 Long 30 for MM 40029 3/8" M 1/4" F 2200 Long 30 PRICING MM 40039 3/8" M 3/8" F 2200 Long 30 MM 43262 * 3/8" M 3/8" F 4000 Short 500 MM 43363 * 1/2" M 1/2" F 4000 Short 300 MM 40502 Seal Kit.......................................................... * 43 Series are rated to 300° F. & 5000 PSI.

Part No. Max. Pressure Max. Flow AA 7475 3000 PSI 10 GPM AA 7475K Repair Kit..............................

D

Maximum Part No. Size Pressure

90° Boom Swivels for ceiling or wall booms as well as hose reels. These swivels have a multiple seal system to prevent leakage under both low and high pressure. Constructed of a nickel-plated brass body with stainless steel internals. NBR o-rings and teflon support rings. Rated to 2200 or 4000 PSI and 250° F. * Available in either short or long stem design for ease in plumbing. Part No.

116

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0077


INLINE SWIVELS

117

Inline Swivels

Inline Swivels

D

D

MPT Swivel

FPT Swivel

Super Swivels "Inline Swivels" are designed with AFLAS™ seals for water, soap or wax solutions. Rated for pressures up to 3,000 psi. Maximum temperature to +400° F. Available in zinc-plated carbon or stainless steel high quality alloy steel. Easily rebuildable. "Live" design swivels under pressure. (For Hydraulic fluids - See Hydraulic swivels with Viton® seals).

Part No. Construction Inlet Port Outlet Port SE SS838-A Plated 3/8" FPT 3/8" FPT SE SS838MF-A Plated 3/8" MPT 3/8" FPT SE SS812-A Plated 1/2" FPT 1/2" FPT SE 14091 * Plated 1/2” FPT 1/2” FPT SE SS812MF-A Plated 1/2" MPT 1/2" FPT SE SS1234 Plated 3/4" FPT 3/4" FPT SE SS1234MF Plated 3/4" MPT 3/4" FPT SE 16015 * Plated 1" FPT 1" FPT SE 1244 Plated 1" MPT 1" FPT SE 1046 Stainless 1" FPT 1" FPT SE SS20AL Plated 1-1/4" FPT 1-1/4" FPT SE SS20MF Plated 1-1/4" MPT 1-1/4" FPT SE 1064 Plated 1-1/2” FPT 1-1/2” FPT SE 1264 Plated 1-1/2” MPT 1-1/2” FPT SE SS8KIT-AL Repair Kit, 1/2" Swivels........................... SE 20183 Repair Kit, 3/4" Swivels........................... SE SS16KIT-AL Repair Kit, 1" Swivels.............................. SE SS20KIT-AL Repair Kit, 1-1/4" Swivels........................ * Double Bearing Design.

Net Ea. $ 29.40 29.40 31.15 50.45 31.00 49.00 49.05 69.65 66.35 194.50 111.00 113.00 208.50 195.50 7.91 15.50 11.50 18.40

Part No.

MM 34853 MM 34863 MM 34854 MM 34864 MM 34855 MM 34865 MM 34856 MM 34866 MM 34857 MM 34867

30 30 30 30 1000 1000 2000 2000

Part No.

MM 34211 MM 34212 MM 34311 MM 34312 MM 34411 MM 34412 MM 34511 MM 34512

Construction

Nickel-Plated Brass Nickel-Plated Brass Nickel-Plated Brass Nickel-Plated Brass Nickel-Plated Brass Nickel-Plated Brass Nickel-Plated Brass Nickel-Plated Brass Nickel-Plated Brass Nickel-Plated Brass

Ports

1/2" M x F 1/2" F x F 3/4" M x F 3/4" F x F 1" M x F 1" F x F 1-1/2" M x F 1-1/2” F x F

Max RPM

30 30 30 30 CALL 30 for 30 PRICING 30 30 30 30

Construction

Max RPM

Stainless Steel Stainless Steel Stainless Steel Stainless Steel Stainless Steel Stainless Steel Stainless Steel Stainless Steel

200 200 150 150 130 130 100 100

CALL for PRICING

Inline Swivels

CALL for PRICING

PARKER PS Series Inline Swivels are designed to eliminate hose twist and torque that may cause premature hose failure. Ideal for hose reels, wash booms and industrial applications.

High Pressure, Hydraulic “Live” Swivels. Available in either “Inline” or “90° angle” styles. Designed for the rigors of hydraulic fluid requirements. Chrome ball bearing design for added life. Easily rebuildable. Superior quality alloy steel. All swivels shown are “inline” design except for 9SS models.

90° Swivel

Ports

1/2" M x F 1/2" F x F 3/4" M x F 3/4" F x F 1" M x F 1" F x F 1-1/4" M x F 1-1/4" F x F 1-1/2" M x F 1-1/2” F x F

DGR Series

—Viton® Seals —

D

DGR FxF

DGE Series

Hydraulic Fluid Swivels

Inline Swivel

D

Max. RPM

MM 30051 1/4" F x 1/4" M MM 30052 1/4" F x 1/4" F MM 30153 3/8" F x 3/8" M MM 30154 3/8" F x 3/8" F MM 31051 * 1/4" F x 1/4" M MM 31153 * 3/8" F X 3/8" M MM 36051 * 1/4" F x 1/4" M MM 36153 * 3/8" F x 3/8" M * Triple Bearing Design.

D

DGR Series feature Stainless Steel bodies, 4 Bearing design. Rated to 3000 PSI and 180° F. RPM varies with size.

DGE MxF

Inline Swivels from No. 30154 No. 30051 Mosmatic. These high quality, inline swivels feature nickel-plated D brass construction with D “dual” stainless steel bearings. Multiple seal system prevents leakage under high or low pressure conditions. Corrosion-resistant design for long life. Compact and lightweight. Rated to 4000 PSI and 250° F. Available in 1/4" or 3/8" FPT or MPT sizes. Sealed design is non-rebuildable. Ideal applications include wash booms, spray wand handles, pressure cleaners. Ports

DGE Series feature Nickel-Plated Brass bodies, one bearing design. Rated to 4000 PSI and 250° F. Maximum of 30 RPM.

D

Inline Swivels

Part No.

Inline Swivels from Mosmatic feature Swiss Engineering and are designed for high flow water and air applications.

Rated to 5000 PSI. Zinc-plated Carbon steel construction with Viton® seals are standard. Maximum temperature to +250° F. Outlet Part No. Inlet Port Port Net Ea. SE SS614 1/4" FPT 1/4" FPT $ 28.40 SE SS614MF 1/4" MPT 1/4" FPT 35.40 SE SS838 3/8" FPT 3/8" FPT 29.40 SE SS838MF 3/8" MPT 3/8" FPT 29.40 SE SS812 1/2" FPT 1/2" FPT 31.00 SE SS812MF 1/2" MPT 1/2" FPT 31.00 SE 9SS83CV * 3/8" FPT 3/8" FPT 32.80 SE 9SS81CV * 1/2" FPT 1/2" FPT 32.95 SE SS8KIT Repair Kit, 3/8” & 1/2” 7.90 SE 20183 Repair Kit, 3/4”......... 15.50 SE SS16KIT Repair Kit, 1”............ 11.50 *90 degree design.

D

Standard Features: Sealed bearings and hardened bearing races for extended service life • Full flow design • Buna or Viton® seals • Teflon backup rings • (Chromium-6 Free) Plated carbon steel construction for added corrosion resistance • Rated to 5000 PSI and 250° F. (Up to 1” sizes) • Available in M x F or F x F NPT ports • Many other port options are available. Male x Female Part No. Size PA PS6101 3/8” M x F PA PS6101V 3/8” M x F PA PS8101 1/2” M x F PA PS12101 3/4” M x F PA PS12101V 3/4” M x F PA PS16101 1” M x F PA PS16101V 1” M x F

Seal Buna Viton® Buna Buna Viton® Buna Viton®

Max. PSI 5000 5000 5000 5000 5000 5000 5000

Net Ea. $ 47.85 58.00 48.65 57.65 81.50 76.95 78.10

Female x Female Part No. Size Seal Max. PSI PA PS6102 3/8” F x F Buna 5000 PA PS6102V 3/8” F x F Viton® 5000 PA PS8102 1/2” F x F Buna 5000 PA PS8102V 1/2” F x F Viton® 5000 PA PS12102 3/4” F x F Buna 5000 PA PS16102 1” F x F Buna 5000 PA PS16102V 1” F x F Viton® 5000 PA PS2420 * 1-1/4” F x F Buna 4000 PA PS2424 * 1-1/2” F x F Buna 4000 * 3-Piece design on 1-1/4” & 1-1/2” sizes.

Net Ea. $ 48.20 60.05 47.00 60.05 62.30 76.05 78.65 484.50 448.00

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0078


WAND SWIVELS BALL BEARING SWIVELS

High Pressure Wand Swivels

Completely Rebuildable

High Pressure Gun Swivels. Brass or stainless steel construction. Rebuildable design. Rated to 200˚ F. Brass rated to 3,000 PSI. Stainless rated to 5,000 PSI.

Pressures to 3500 PSI High Pressure Swivel with Brass body and Stainless Steel thrust bearings. Internally lubricated O-rings and 303 Stainless center spool piece assure long trouble-free operation. Pressures to 3500 PSI. Maximum temperature is 160° F. Part No.

D

D

D D

Pipe Thread Ports Max. PSI

Net Ea.

FL SW504 1/4" MPT x 1/4" FPT 2000 FL SW504A 3/8" MPT x 3/8" FPT 2000 FL SW504HP 1/4" MPT x 1/4" FPT 3500 FL SW504AHP 3/8" MPT x 3/8" FPT 3500 FL RK550 Repair Kit for swivels above....................

$ 18.25 18.65 18.60 20.25 8.25

2400-32 or 2400-34

Part No. AA 7045 AA 7080 AA 7044 AA 7084

Ball Bearing Swivels are of Electroless Nickel plated Brass construction. Cap ends are precision machined for heavy-duty leak proof service. High pressure seal is Buna-N. Bearing seal is vented between the high pressure seal. Maximum pressure is 1500 PSI. Maximum Temperature is 180° F. Part No.

D

2400-31 or 2400-33

Pipe Thread Ports

7044

7080

SWIVELS D

118

Net Ea.

Material Size Max. PSI Net Ea. Brass 3/8" F X F 3000 $ 11.25 Brass 3/8" M x F 3000 11.20 Stainless 3/8" M x F 5000 16.55 Repair Kit for above swivels......... 2.15

Wand Swivels High Pressure Wand Swivels from U.S. ParaPlate. Rated to 3000 PSI at up to 10 GPM. Available in either brass or stainless construction. Maximum temperature is 300° F. Part No.

Material

SM 2400-31 1/4"MPT x 1/4"FPT $ 17.70 SM 2400-32 1/4"FPT x 1/4"FPT 17.70 SM 2400-33 3/8"MPT x 3/8"FPT 17.70 SM 2400-34 3/8"FPT x 3/8"FPT 17.70 SM 523-0690 Repair Kit for above swivels 5.76

Wand Swivels Easy turn gun swivels for high pressure spray wands. High quality, SwissMade, construction. Rated to 4000 PSI & 250° F. Nickel-plated brass body, stainless steel bearing. Nitrile o-ring.

Swivels High Pressure Swivels from Suttner! Available in 3/8" MPT x FPT or 3/8" FPT x FPT. Rated to 5100 PSI. Maximum temperatures to 300° F. Rated to 5 GPM. Nickel-plated brass or stainless construction. Rebuildable design. Ports Type Net Ea. 3/8" M x F Brass $ 9.95 3/8" F x F Brass 11.15 3/8" M x F Stainless 27.55 Repair Kit................... 8.44

Part No.

High Flow Swivels High Flow, 1/2” Swivels from Suttner! Available in Nickel-Plated Brass or Stainless construction. Teflon rings allow temperatures to 195° F. Rated to 3600 PSI and 42 GPM. Ports are 1/2” male inlet x 1/2” female outlet

D

Part No. Type

NP ST340 NP ST340S

High Flow Swivel High Flow Swivel

CALL for PRICING

High Pressure Swivels Stainless Steel or brass construction. Bearings are self-lubricated Teflon filled acetal for long life and low torque requirements. Maximum temperature is 200° F. Ports are 3/8" FPT x 3/8" MPT.

D

Net Ea.

Medium Pressure Swivels

Mounts between hose and gun, designed to break before damage to gun or wand. Available in 1/4" or 3/8". Rated to 4,000 PSI.

D

D

Part No.

Part No. Net Ea. AA 5068 1/4" MPT x FPT $ 1.85 AA 5069 3/8" MPT x FPT 1.95

SM 902-1/4 SM 900-3/8 SM 901-1/2

(800) 228-9666

4000 4000 4000 4000 4000 4000 4000 4000

SS 15950SS Stainless Steel ..................... 3000 $ 52.95 SS 15950B Brass ................................... 3000 33.45 SS AB15950 Repair Kit.......................................................... 14.50

$ 18.00 37.30

Break-Away Gun Fittings

DULTMEIER SALES • OMAHA, NE

Max. PSI

Part No. Material Max. PSI

Net Ea.

Brass Stainless

Ports

MM 32569 3/8" FPT x 3/8" FPT MM 32564 3/8" MPT x 3/8" FPT MM 32563 3/8" MPT x 3/8" MPT MM 32562 3/8" MPT x 1/4" FPT MM 32561 3/8" MPT x 1/4" MPT MM 32557 1/4" FPT x 1/4" FPT MM 32863 *1/2” MPT x 1/2” MPT MM 32864 *1/2” MPT x 1/2” FPT * High Flow Swivels

D

D

Net Ea.

UP 16003 Brass 3000 $ 12.25 UP 16003SS Stainless 3000 16.00

D

Part No. NP ST300 NP ST325 NP ST310 NP ST300K

Max. PSI

D

www.dultmeier.com

Ideal for pumping systems up to 1000 PSI. No Ball Bearings to gall or rust. All Brass Body. Available in 1/4", 3/8" and 1/2" sizes. Non- repairable. Pipe Thread Ports

Max. PSI

Net Ea.

1/4" MPT x 1/4" FPT 3/8" FPT x 3/8" MPT 1/2" FPT x 1/2" MPT

1000 1000 1000

$ 7.10 7.30 11.15

• DAVENPORT, IA

(800) 553-6975

E0076


Trigger Spray Guns

119

Spray Wands for Car & Truck Wash

Special Application Spray Wands

Suttner Trigger Wands are designed for the Car and Truck Wash Industries. Forged brass housings for maximum strength. Contour design for operator comfort. Available with Zero Leak or Weep seats. Rebuild kits are available for all models. Inlet ports are all 3/8” FPT. Outlet ports are 1/4” FPT. Rated to 300° F.

Suttner Special Application Wands have a unique construction and design for a wide range of applications. Rated to higher flow rates and pressures than standard Suttner wands. Rated to 300° F. ST2000 Series. Our most popular industrial gun. Designed for heavy duty durability. 3/8” inlet x 1/4” outlet. ST2750 Series. Tungsten carbide ball and special seal allow this gun to be used up to 7300 PSI. Relax action trigger reduces holding force by up to 90%. 3/8” inlet x 1/4” outlet.

ST1100 Series. The most lightweight and economical Suttner gun. Rated to 7 GPM at 3000 PSI. Zero leak only. Rear entry design. ST1500 Series. The industry standard for over 25 years. Still our most popular gun. Rated to 12 GPM at 5000 PSI. Rear entry design. Available in weep and zero leak. Model ST1500HH is a wand only without trigger. Ideal for use with triple foam wax systems.

ST601 Series. Ideal for vertical and overhead cleaning. Inline design is an industry standard for use with telescoping wands and extensions. 3/8” inlet x 1/4” outlet.

ST810 Series. Front entry design keeps hoses away from operator. Rated to 8 GPM at 3000 PSI. Zero leak version includes poly seat for added chemical resistance. Weep style also available but without poly seat.

ST2700/ST2720 Series. Stainless steel valve components for use with corrosive chemicals as well as meeting food industry requirements. Two different flow rates and pressures to choose from. 3/8” inlet x 1/4” outlet.

ST2300 Series. Unique, “easy-pull trigger” requires nearly half the effort of other spray guns. Rated to 12 GPM. Model ST2315 features a ceramic ball which is highly resistant to acids and presoaks. Available in weep and zero leak. Rear entry design.

ST2620/ST3600/ST3300 Series. All of these wands are designed for high flow applications. ST2620 has 3/8” inlet x 1/4” outlet. ST3300 & ST3600 have 1/2” inlet x 1/2” outlet. ST860D and ST4000 Steam Wands. Rated to 290 PSI and 392° F. ST860D is trigger wand only with 1/4” FPT inlet and outlet. ST4000 is trigger wand and extension. Inlet is 3/4” FPT. Overall length is 30”.

ST2600 Series. Exclusive “relax-action” trigger reduces trigger force up to 40% and holding force up to 90%. Great choice for truck wash and mobile cleaning applications. Rated to 12 GPM and 5000 PSI. Zero leak only. Rear entry design.

D

D D

D

D

D

ST2620

ST2000

ST1500

ST1100

ST810

D

D

D

D

D

ST1500HH

ST2300

ST2720

ST2300W

ST2700

ST2750

D

ST3300

ST4000 Steam Wand Assembly

D D

D

D

D

ST2600

ST860D

Trigger Wand Only

ST2315 ST3600 ST601 Part No. Seat GPM PSI Net Ea. NP ST2750 Zero 8 7300 $ 119.50 NP ST2000 Zero 10 5000 21.20 NP ST601 Zero 12 4000 21.25 NP ST2700 ** Zero 12 5000 71.50 NP ST2720 ** Zero 21 1800 107.50 NP ST2620 Zero 21 1800 51.05 NP ST3600 Zero 21 8700 184.00 NP ST3300 ** Zero 27 2150 149.50 NP ST860D Zero - 290 44.95 NP ST4000 Zero - 290 317.00

Part No. Seat GPM PSI Net Ea. NP ST1100 Zero 7 3000 $ 16.30 NP ST1500HH - 5 100 10.75 NP ST1500 Zero 12 5000 17.95 NP ST1500W Weep 12 4000 19.60 NP ST810 ** Zero 8 2000 15.90 NP ST810W Weep 8 3000 16.25 NP ST2300 Zero 12 5000 22.55 NP ST2300W Weep 12 4500 21.00 NP ST2315 ** Zero 12 5000 39.95 NP ST2600 Zero 12 5000 25.90 ** Special features for added chemical resistance. DULTMEIER SALES • OMAHA, NE

(800) 228-9666

** Stainless Steel Components.

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0072


Trigger Spray Guns Trigger Guns

MV Trigger Guns

Giant Trigger Style Spray Guns. Rated to 10 GPM and 5000 PSI these guns will handle a wide variety of cleaning applications.

Great Choice for car wash, truck wash or pressure wash applications. Available in weep or non-weep versions. Contour design and easy trigger pull for ease of use. Exact replacements for many of the popular spray guns on the market today. Brass 3/8” FPT inlet and 1/4” FPT outlet. Rated to 300° F.

Available with stainless steel discharge ports. Also available with Zero leak or Weep style seats. 3/8" FPT inlet and 1/4" FPT outlet. Maximum Temperature is 300° F.

D

Part No. Inlet Outlet Seat Net Ea. GU 21290B Brass Plated Zero $20.85 GU 21295B Brass Plated Weep 20.85 GU 21250B Brass S.S. Zero 29.95 GU 21255B Brass S.S. Weep 30.75 GU 21227 Repair Kit, 21250B & 21290B..... 4.82 GU 21240 Repair Kit, 21255B & 21295B..... 5.37

21295B

920 (7 GPM)

3/8" Inlet Rear Entry

Trigger Guns

3/8" Inlet Front Entry

Part No.

Seat

MV 920 MV 920W MV 951

Zero Leak Weep Style Zero Leak

General TriggerWands feature contour design and smooth trigger pull.Stainless steel ball and Viton® seat are standard. YG5000 and YRL20 models feature brass inlet and outlet fittings. DG Series Wands have plated ports. YRL Model is a front entry style, all others are rear entry. Maximum temperature is 320° F. Seat

IP YRL20 * Zero IP DG4000 Zero IP DG5010W Weep IP DG4512 Zero IP YG5000 Zero

Max. Flow

Max. PSI

Net Ea.

8 GPM 8 GPM 10 GPM 12 GPM 10 GPM

3200 4000 5000 4500 5000

$ 17.95 13.75 13.75 19.40 27.95

Adams Model 5030 Trigger Guns. Available with “weep” or “zero leak” seats. Designed with 3/8" FPT brass inlet and 1/4" FPT brass discharge port. Standard Features: Stainless steel seat, ball and actuator pin • Glass-filled handle • Nylon construction • Maximum temperature is 300° F. Seat

AA 5030 AA 5030W

Zero Weep

Max. PSI

Max. Flow

Net Ea.

4500 4500

12 GPM 12 GPM

$ 24.80 24.80

Seats

Part No.

Inlet

Outlet

3/8" FPT 3/8" FPT 3/8” FPT

1/4" FPT 1/4" FPT 3/8” FPT

Replacement Seal for UST-0 & UST-1 Guns.. 1.75 Repair Kit for UST-0 and UST-1 Guns........... 19.35 DULTMEIER SALES • OMAHA, NE

Ports

Max. PSI

Max. GPM

Net Ea.

D

Max GPM

Max. PSI

Net Ea.

http://www.dultmeier.com or E-Mail us at dultmeier@dultmeier.com

$ 27.95 27.95 35.95

(800) 228-9666

Seat

Visit Our Web Site at

Net Ea.

UP 35020 UP 40054

2002SS

HY 3381-32 Zero 7.0 4000 $ 26.05 HY 3381-32W Weep 7.0 4000 27.20 HY 3430-402 Seat Kit, Zero Leak................. 7.85 HY 3430-465 Seat Kit, Weep........................ 10.55

Front Entry Style

Zero Leak Weep Style Zero Leak

D

MV 2002 Brass 5000 12 $ 25.50 MV 2002SS Stainless 5000 12 119.50

Part No.

D

UP UST-0 UP UST-1 UP UST-2

Non-Slip Grip

D

Model 32 Trigger Wand handles for car washes or pressure washing. Designed to fit comfortably in the contour of your hand with an easy trigger pull. Rated to 7 GPM and 4000 PSI. Maximum temperatures to 300° F. Inlet is 3/8" FPT. Outlet is 1/4" FPT.

Features: Glass reinforced plastic body • Stainless Steel seat insert, ball and actuating rod • Forged brass valve housing • Viton® seals • Available with either zero-leak or weep-style seats • Good balance and light trigger pull • No liquid flow through the handle so 300 degree fluids can be used comfortably • Extremely durable, yet lightweight • 3/8" FPT inlet pipe is standard. Part No.

$ 18.35 19.50 20.95

Trigger Guns

TYPE - II TRIGGER GUNS These rugged lightweight guns are durable enough for continuous on/off operation in self-ser vice Car and RV washes; water and chemical pressure cleaning. Ratings: 3000-PSI, 10-GPM & 300° F.

Net Ea.

4000 4000 5100

Designed for the pressure washer and truck wash industry. Heavy duty, unique gun features a soft, non-slip rubber grip for ease of use. Zero Leak design. Rated to 12 GPM, 5000 PSI and 320° F. Standard with 3/8” FPT inlet and 1/4” FPT outlet. Brass or Stainless construction.

TRIGGER GUNS

Part No.

Max. PSI

2002

* Front Entry Style. D

Flow

7 GPM 7 GPM 10 GPM

Pressure Wash Spray Wands

DG/YG Models

Part No.

951 (10 GPM)

920W (7 GPM)

D

D

YRL20

D

D D

1/4" Outlet

1/4" Outlet

120

Viton® is a registered trademark of DuPont Performance Elastomers

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0073


Spray Guns & Extensions

121

Easy Pull Spray Wands TRIGGER GUNS AL19 Trigger Wands are a popular gun for pressure wash and car wash applications. Contour design means they are easy to hold and use. Rated to 8 gpm @ 4500 PSI and 300° F. Ports are brass. Available with zero leak or weep seats. Inlet is 3/8” FPT. Outlet is 1/4” FPT.

D

Maximum Part No. Seats PSI

Flow Rate

Net Ea.

AR AL36 AR AL19W

8.0 GPM 8.0 GPM

$ 16.70 24.95

Zero Leak Weep Style

4500 4500

Heavy-Duty, Light Trigger Spray Wands are ideal for truck wash, mobile cleaning and pressure washer applications. 3/8” FPT plated inlet x 1/4” FPT brass outlet. High flow and pressure ratings as shown. Zero leak seats are standard. Rated to 320° F. Model SG35A is the same as SG35 but has seals rated for acid solutions.

SG35

D D

SG40

BYPASS/DUMP GUNS Bypass or Dump Guns are designed to allow low pressure spray while the trigger is in the released position and high pressure when the trigger is pulled. Protection against freeze-up with no restriction through gun to prevent freeze control flow. General or Cat.

Part No.

Max. PSI

Max. Flow

Net Ea.

MV SG35 MV SG40 MV SG35A

5000 5800 * 5000

12 GPM 8 GPM 12 GPM

$ 17.45 18.60 18.50

* Rated for Acid Solutions. 1/4” Stainless Outlet

D

Specifications: Maximum flow is 10 GPM • Maximum pressure rated to 3000 PSI • Maximum temperature rating is 140° F. • Weight: 32 oz.

TRIGGER GUNS Front Entry

YG3000DS

Barrel Part No. Brand Length

IP YG3000DS GENERAL IP YG3000D GENERAL CC 32300 CAT CC 32301 CAT

16" 40" 15" 39"

Inlet

3/8" FPT 3/8" FPT 3/8" FPT 3/8" FPT

Outlet

Heavy-Duty design to withstand high impact and rough use. Smooth and easy to operate. Trigger lock retracts flush in handle. Stainless steel shut-off needle. Bronze-filled Teflon seat.

Net Ea.

1/8" FPT $ 68.10 1/8" FPT 76.40 1/8" FPT 96.65 1/8" FPT 121.50

Series 30: Pressures to 1500 PSI, Maximum Temperature 200° F., Maximum Flow 5 GPM, BUNA stem seal. Inlet is 1/4" FPT. Outlet is 1/4" FPT. Series 60: Pressures to 2500 PSI, Maximum Temperature - 300° F., Maximum flow is 6 GPM, Viton® stem seal. Inlet is 3/8" FPT. Outlet is 1/4" FPT.

TRIGGER GUNS

D

Part No. SS 30-1/4 SS 60-3/8 SS AB30KIT SS AB60KIT

Ideal for self-serve car wash use or general cleaning applications. Durable heat resistant trigger means longer life, less breakage • Contour design and smooth trigger action reduces operator fatigue • Stainless steel ball and seat • Rated to 300° F. • 3/8" FPT Inlet and 1/4" FPT Outlet. Part No.

Seat

Max. PSI

Max. Flow

D

Net Ea.

CC 76150 Zero 3000 8.0 $ 32.90 CC 76151 Weep 3000 8.0 33.85 CC 36130 Zero 4000 10.5 53.50 CC 36131 Weep 4000 10.5 53.50

Seat Inlet Outlet PSI Net Ea. Zero Leak 1/4" FPT 1/4" FPT 1500 $ 32.50 Zero Leak 3/8" FPT 1/4" FPT 2500 44.95 Repair Kit for 30-1/4 GunJets......................... 7.95 Repair Kit for 60-3/8 GunJets ........................ 22.45

Spray Wands with Extensions Spray Gun/Extensions Units for replacements on box store pressure washers. Extension outlets are 22mm and designed for AL248 spray lances. Gun inlet is either 3/8” FPT or 22mm to match up to 22mm or 3/8” MPT hose assemblies. BT105 Spray wand has 22mm inlet x 22mm extension outlet. Extension is 19” long. Rated to 8 GPM, 3000 PSI and 212° F.

BT105

AL12 Spray wand has 3/8” FPT inlet x 22mm extension outlet. Extension is 19” long. Rated to 8 GPM, 3000 PSI and 140° F. AL248 Spray lance is designed with 22mm inlet to match to wands above. Outlet is 1/4” MPT. Length is 24”. Rated to 10 GPM, 5000 PSI and 300° F. Zinc construction.

Call Us For All Your Car Wash & Truck Wash Needs!

AL248C Spray lance is designed with 22mm inlet to match wands above. Outlet is 1/4” female quick coupler.Length is 24”.Rated to 10 GPM, 5000 PSI and 300° F. Zinc construction.

SERVICE & REPAIRS Did you know? We can service almost every brand of pump we sell in our catalog.

Part No. AR BT105 AR AL12 AR AL248 AR AL248C

Call us at 1-800-228-9666 (Omaha, NE) for a quote!

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

AL12 D

AL248 & AL248C

Description Inlet Outlet Net Ea. Spray Gun with Extension.... 22mm 22mm $ 17.30 Spray Gun with Extension.... 3/8” FPT 22mm 19.95 24” Lance............................. 22mm 1/4” MPT 7.09 24” Lance............................. 22mm 1/4” QC 13.25

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0875


Wash Down Guns & Nozzle Protectors Wash Down Spray Guns These popular wash down guns are used in a variety of industries for clean up and disinfecting. Variable spray from solid stream to 50 degree pattern is controlled at the trigger. Rated to temperatures up to 200° F. and pressures to 150 PSI. Body is aluminum and is covered by a replaceable White, Nitrile rubber grip. Trigger is stainless steel. Available in 10, 16 or 22 GPM units. Inlet port is 1/2" female pipe thread. Part No.

SS CU1501 SS CU1502 SS CU1503

Rating

ST004

Part No. NP ST004-D42 NP ST004-D44

Suttner Industrial Spray Guns are an ideal choice for plant or bay washdown. Spray pattern is adjustable. Thick, rubber sheathing protects against heat, cold and impact. Rated to 700 psi and flows to 27 gpm. Maximum temperatures to 190° F. Inlet port is 1/2" FPT. Weight is 28 oz.

Part No.

Rating

Part No. MV 1830

Part No. GS ST10 GS ST15

Inlet Nozzle Type 1/4" FPT 1/8" MPT 1/4” FPT 1/4” MPT

Color Black Black

Net Ea. $ 2.79 2.79

140 Nozzle Protectors are made of a heavy plastic and are held in place by the nozzle and wand. The base acts like a washer to hold both together. Overall Length is 2-1/8”. Available in blue, red or black. One-piece design. Also commonly used on triple foam wands.

Adjustable Pattern Wash Down Gun. Rated to 195° F. Flows to 16 gpm and pressures to 350 psi. Discharge cone is adjustable for wide to narrow patterns. Inlet is 1/2" FPT. Weight is 2.1 lbs.

Part No. BC 140 BC 140B BC 140R

D

Net Ea.

1830

ST10 / ST15 Nozzle Protectors feature a brass, 1/4” FPT inlet and hard plastic upper cover. Designed for any 1/4” wand extensions including spring type flex extensions. Overall length is 1-1/4”. Rated to 2000.

ST10 ST15

Net Ea.

Wash Down Spray Gun

D

Inlet Nozzle Type Color Net Ea. 1/4" FPT 1/4" MPT Black $ 1.21

D

* Food Grade.

Rating

Inlet Nozzle Type Color Net Ea. 1/4" FPT 1/8" MPT Black/Gray $ 2.96 1/4” FPT 1/4” MPT Black/Gray 2.96

1830 Nozzle Protectors features a 1/4” FPT plated inlet. Heavy wall, plastic construction is standard. Rated to 5100 PSI and 320° F. Designed for 1/4” MPT nozzles. Overall length is 2”.

NP ST1200 Wash Down Gun, Brass 27 GPM $ 75.10 NP ST1200SS Wash Down Gun, Stainless * 27 GPM 239.00

Part No.

ST004 Nozzle Protectors feature a two piece design where the tough, plastic outer cover threads on to a plastic base. Zinc-plated, 1/4” FPT inlet fitting is housed in the base. Available for either 1/8” or 1/4” MPT nozzles. Rated to 5,000 PSI and 210° F. Overall length is 2-1/2”.

D

Rated to Temperatures up to 200° F.

Wash Down Spray Gun

Maximum Temperatures to 190° F.

D

Part No. Inlet Nozzle Type Color Net Ea. NP ST107 1/4" FPT 1/4" Black/Red $ 4.85 D

$ 125.00 125.00 125.00

D

NOZZLE PROTECTORS Designed to protect vehicle surfaces from scratching and damage. Nozzles are completely surrounded by protector guards. Different style designs are shown below. ST007 Nozzle Protectors feature a Soft outer edge to protect surfaces and a Hard Plastic Base for added wear life. Inlet port is 1/4” FPT Stainless steel. Rated to 5,000 PSI and 300° F. Designed for 1/4” MPT nozzles. Over length is 2”. ST107

Net Ea.

10 GPM 16 GPM 22 GPM

122

Inlet - - -

D

Nozzle Type Color 1/8” or 1/4” MPT Blue 1/8” or 1/4” MPT Black 1/8” or 1/4” MPT Red

Net Ea. $ 1.50 1.50 1.50

IP YG1635 Wash Down Gun 16 GPM $ 73.55

Wash Down Wands

D

Super Kleen Trigger Guns are designed for plant washdown, truck wash, tank cleanout and industrial cleaning. Rated to 12 gpm @ 150 psi at up to 200° F. Rear mounted levers reduce hand fatigue and offer smooth lever action. Variable spray pattern is adjustable from fan spray to solid stream. Inlet Port is 1/2” FPT. Drip-free automatic shutoff is a standard feature. Available in Brass, Aluminum or Stainless Steel construction with Blue, White, Red or Gray covers. All covers are easily replaceable if required.

Standard Brass Part No.

VD 150ALB VD 150AR VD 150AW VD 150BB VD 150BR VD 150BW VD 150SG

Standard Aluminum

Rear Handle Design D

22005

22002

Part No. Inlet GS 22002 - GS 22005 -

Aluminum Aluminum Aluminum Brass Brass Brass Stainless

Light Blue Red White Dark Blue Red White Gray

1.7 lbs. 1.7 lbs. 1.7 lbs. 3 lbs. 3 lbs. 3 lbs. 2.8 lbs.

Part No. Inlet Nozzle Type Color NP ST005 - 1/8” or 1/4” MPT Black

DULTMEIER SALES • OMAHA, NE

Net Ea.

(800) 228-9666

Color Blue Black

Net Ea. $ 2.39 2.39

ST005

Net Ea. $ 1.25

D

Nozzle Protectors No. 26110-PUR Nozzle Protector

$ 73.95 78.95 80.95 94.75 96.50 93.95 164.00

Nozzle Type 1/8” or 1/4” MPT 1/8” or 1/4” MPT

ST005 Nozzle Protectors are made of a heavy duty, flexible rubber. Compact design is only 1” long. Held in place by the nozzle and the wand extension. For 1/8” or 1/4” MPT nozzles.

D

Body Material Cover Wt.

2200 Series Nozzle Protectors are made of heavy but flexible plastic and are held in place by the nozzle like the 140 series above. Overall length is 2-1/4”. Available in blue or black. One-piece design.

D

Durable and abrasion resistant polyurethane nozzle protectors. Shields the spray surface from damaging contact during use and at shut-off.

1/8MEG or 1/4MEG WashJet Nozzle

D

CP26110-PUR

Also protects the nozzle & extends wear life. One size fits both 1/8" & 1/4" MEG nozzles up to #20 orifice. Maintains shape and durability from below freezing to 250° F. Part No. Net Ea.

SS CP26110-PUR •

www.dultmeier.com

• DAVENPORT, IA

Nozzle Protector

(800) 553-6975

$ 1.62 E0706


Spray Guns & Wands

123

1/4” Quick Coupler

Adjustable High Pressure Wand Extension Assemblies

Trigger Hand Operated Spray Guns 22670PP-1/4-15

Extensions/Gun/Hose Assemblies designed for use with pressure washers to effectively clean to 24' while still on the ground. Great for cleaning siding, windows, buildings, etc.

D

Extensions feature trigger spray gun, high pressure hose and adjustable extension, (Nozzles not included). Units are assembled and ready to hook-up to your pressure washer. Rated to 4000 PSI. Available in 3 sizes.

22650PP 38720-PPB Tip

Polypropylene Wands with a Polyester Extension. Can be used with bug spray, tire cleaner and presoak solutions. Designed for ease and comfort in operation.Trigger lock permits locking of valve in open position for continuous flow of liquid. Maximum pressure is 150 PSI. Viton® diaphragm. 1/4" FPT or 3/8" HB inlet connection. Extensions included on 15" & 24" units.

Features: Units assembled and ready to hook-up • Trigger spray gun • High pressure hose • a • Adjustable extension • Rated to 10 GPM • Rated to 4000 PSI • Rated to 195° F. D20015

Part No. Description Net Ea. Support Belt SS 22650-1/4PP Spray Gun Only, 1/4” FPT........................ $ 14.30 SS 22650PP Spray Gun Only, 3/8” HB......................... 14.30 Part No. Size Wt. Net Ea. SS 22670PP1/4-15 15” Spray Gun, 1/4” FPT & #8 Nozzle †.. 22.90 DU 612EX 6'-12' Adjustable Extension Assembly 9 lbs. $ 84.95 SS 22670PP 15” Spray Gun, 3/8” HB & #8 Nozzle †.... 22.65 DU 618EX 6'-18' Adjustable Extension Assembly 9 lbs. 85.95 SS 22670PP-24406 24” Spray Gun, 3/8” HB & #8 Nozzle †.... 26.45 DU 624EX 9'-24' Adjustable Extension Assembly 14 lbs. 97.75 SS PKAB22670PP Repair Kit for Spray Gun.......................... 8.44 IP D20015 Support Belt for 612EX / 624EX - 14.10 SS 22665-15PP Extension less Nozzle & Adapter............ 6.13 SS 22665-24PP Extension less Nozzle & Adapter............ 10.20 1.30 SS CP22673PP 45˚ Adapter.............................................. MPT Inlet SS 5500X3 thru X10 Brass Adjustable Nozzle.......................... 10.60 SS 5500PPB-X3 thru X8 Poly Adjustable Nozzle............................ 4.80 Trigger Valves for detailers, bug sprayers, D 3.54 SS 38720-PPBX8 * 45˚ Adjustable ConeJet Assembly........ tire cleaners, etc. Rated to 2 gpm and * Also available in X12, X18 & X26 sizes also. † Extensions Included on these models.

Brass Trigger Valves

250 psi. Model 6590 is valve only with 1/4" FPT inlet and outlet ports. Model 6466-4727 is a brass GunJet with rubber grip for use with any of the Spraying Systems caps. Inlet connection is 1/4" MPT. 1/4” FPT

Lightweight Spray Guns D

38720-PPBX8

6590 D

1/4” FPT Inlet

Outlet

Lightweight Polypropylene Gun for use with back pack and other low pressure sprayers. Available with a 15" polypropylene or 21" aluminum extension. 3/8" Hose barb inlet connection. Trigger lock and internal strainer. 100 psi maximum pressure. Threaded outlet for use with any standard TeeJet tip but comes standard with a adjustable conejet tip. Part No. SS 50800-38ALX12 SS 50800-38PPX12 SS 38720-PPBX8

6466-4727

Outlet

Cap Thread Extension

Part No.

Brass Trigger Valves

Net Ea.

SS 6590 Trigger Valve, Buna, 1/4” FPT Inlet..... $ 23.95 SS 6590VI Trigger Valve, Viton®, 1/4” FPT Inlet... 26.95 SS 6466-4727 Trigger Valve with grip, 1/4" MPT Inlet 31.25

Wand Handles (Foam Systems)

438 Wand Handles are ideal for use with triple foam wax and clear coat wax Description Net Ea. systems. Handles are standard with nozzle tip protector and feature 3/8" FPT inlet Spray Gun with 21" Aluminum x 1/8" FPT outlet. Available in Blue, Red or Black. Nozzle protectors are available Extension & #12 Nozzle................. $ 10.50 separately and can also be used with high pressure spray wands. ST1500HH is a Spray Gun with 15" Polypropylene wand handle only, blue in color. Extension & #12 Nozzle................. 8.77 * Adjustable ConeJet Nozzle.......... 3.54

* X12, X18 & X26 Nozzles available.

Steam Wand Assembly

140 Series Tip Protector Only

DD

Maximum Maximum Temperature Pressure

NP ST4000

390° F.

290 PSI

Net Ea.

$ 317.00

Break-Away Gun Fittings D

1/4" FPT Outlet Fitting

3/8" FPT Inlet Fitting

Viton® is a registered trademark of DuPont Performance Elastomers

(800) 228-9666

WAND HANDLES

Urethane -Coated Wand Handles for use with PreSoak, Clear Coat or Triple Foam Systems. Black in color. Model 257 is galvanized steel pipe and fittings.

D

Part No. Net Ea. AA 5068 1/4" MPT x FPT $ 1.85 AA 5069 3/8" MPT x FPT 1.95

Net Ea. $ 11.50 11.50 11.50 1.50 1.50 1.50 10.75

For 1/4” Extensions

Mounts between hose and gun or between gun and extension, designed to break before damage to gun or wand. Available in 1/4" or 3/8". Rated to 4,000 PSI.

DULTMEIER SALES • OMAHA, NE

D D

Part No. BC 438 Blue Wand Handle with Protector....................... BC 438B Black Wand Handle with Protector..................... BC 438R Red Wand Handle with Protector....................... BC 140 Blue Tip Protector ONLY................................... BC 140B Black Tip Protector ONLY.................................. BC 140R Red Tip Protector ONLY..................................... NP ST1500HH Blue Wand Handle ONLY, Suttner......................

Trigger Style Steam Wand. For use with Steam Wash Systems. Rated to 390° F. and 290 PSI. Inlet is 3/4” FPT. Includes wand extension and steam nozzle. Overall length is 30”. Part No.

Suttner ST1500HH

438 Series Wand Handle with Tip Protector

D

Model 357S is stainless steel pipe with stainless steel inlet and outlet fittings. Part No.

Description

BC 257 BC 357S

Wand Handle with galvanized fittings..... $ 11.50 Wand Handle with S.S. fittings ............... 13.25

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

Net Ea.

E0656


Spray Gun Accessories

124

Flex Lance Extensions

Wand Holders

Flexible Spray Gun Extensions: Plated, Galvanized or Stainless Steel extensions with flexible center section. Available in 18" or 24" lengths. Inlet port is 1/4" MPT. Outlet port is 1/4" MPT x 1/8" FPT (for male or female nozzles) except 291P which is a 1/8” FPT only. Maximum operating pressure is 2250 PSI. Maximum operating temperature is 200° F. Blue or Black covers.

High Quality, Swiss-Made, Stainless Steel Wand Holders from Mosmatic. Available in flexible spring, floor mount version or rigid wall mount version. Smooth, rounded inlet protects wands and hose from sharp edges. Diameter is 2”.

Part No. Material Length Cover Net Ea. BC 291P-18 * Plated 18" Blue $ 8.77 BC 291P-18BK * Plated 18" Black 8.77 BC 291G-18 Galvanized 18" Blue 14.10 BC 291G-18BK Galvanized 18" Black 14.00 BC 291G-24 Galvanized 24" Blue 17.60 BC 291G-24BK Galvanized 24" Black 17.60 BC 291S-18 Stainless 18" Blue 17.20 BC 291S-18BK Stainless 18" Black 17.20 BC 291S-24 Stainless 24" Blue 22.35 * Outlet is 1/8” FPT Only - USA.

29097 Wand Holder Spring Model Floor Mounted with Recovery Port 29099 Wall Bracket Converts Floor Spring Wand to Wall Mount.

Part No.

Type

MM 29097 MM 29083 MM 29099

Flexible Spring Wand

Length

Stainless Steel

Flexible wand extensions with heavy-duty spring. Designed to allow for easily cleaning under wheel wells, bumpers, etc. Overall length is 15". Ports are 1/4" MPT x 1/8” F nozzle protector. Part No. Length BC 299S Flex Wand 16"

Wt.

Floor, Spring 26" 7 lbs. Wall, Rigid 23" 4 lbs. Wall Bracket............................................

CALL for PRICING

18"

Wand Holders

Model 299S

29083 Wand Holder Wall Mounted

D

6"

711BS D

Net Ea. $ 12.95

22" D

759B

Insulated Grips

722BS

Used with existing spray wands. All grips can be used on any 1/4" wand pipe, extension or barrel.

Model 711BS is a 2-1/2" stainless tube with flared open ends to prevent water accumula­tion. Overall length is 18". Standard with mounting tabs.

ST009 handle grip slides through the opening at the top giving you a comfortable handle.

Model 722BS is the same as 711BS, but is 22" long for longer extensions. Model 759B is a 2" x 6" stainless steel wand holder. Ideal for Triple Foam Systems.

ST9 is a 14", 2-piece, molded plastic, vented cover that is assembled over the existing pipe for operator protection. Rated to 300° F.

Model 711B-SST is a stainless steel tube “Flex” wand holder featuring 2-1/2" Stainless steel tube. Overall length is 26". Heavy spring at 711B-SST bottom helps to eliminate damage Shown with from van­dalism. Designed with Wand & Gun a nipple at the bottom (wall mount) for use with re711B-SST-FL circulating weep systems FLOOR MOUNT if re­ q uired. Available in wall or floor mount Flush Mount Plate styles.

ST9H is a combination of the ST009 and the ST9 that gives you a hand grip and insulated cover. Rated to 300° F. D

D

Model ST9 14" Vented Cover

Model ST009

26"

WALL MOUNT

D

Model ST9H with side handle

D

Part No.

Description

NP ST009 NP ST9 NP ST9H

Plastic Handle for 1/4" tube extensions.. $ 6.11 14", 2-Piece, Vented Grip........................ 5.95 Grip with side Handle.............................. 10.35

711B-SST

Net Ea.

Weep Nipple

Designed for use with high pressure trigger wands. Unique design allows for use as a straight wand or adjustable angles for hard to reach places like wheel wells or gutters. Pulling the insulated grip backward, changes from straight to as much as a 90° angle. Slide the grip forward and it returns to a straight wand. Construction is zinc-plated steel. Rated to 3000 PSI and Shown in "pull" 300° F. Length is 33". Inlet and outlet position is 1/4" MPT.

D

258

Insulated Fore Grips: Molded urethane grips. Constructed to fit 1/4" gun extension wands. Provides insulation when spraying hot liquids. Length

Net Ea.

Part No.

BC 258 6" $ 3.96 BC 259 11" 4.31 DULTMEIER SALES • OMAHA, NE

Part No. Net Ea. NP 759B Stainless Steel Wand Holder, 6".......... $ 14.50 NP 711BS Stainless Steel Wand Holder, 18"........ 28.50 NP 722BS Stainless Steel Wand Holder, 21"........ 30.95 NP 711B-SST S.S. Flex Wand Holder, 26" - Wall Mount........ 63.95 NP 711B-SST-FL S.S. Flex Wand Holder, 26" - Floor Mount....... 66.95

D

Part No.

D

Push/Pull Spray Lance

Insulated Wand Grips 259

26"

Length

Net Ea.

NP ST85 34" $ 80.70

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0075


Spray Wand Extensions

125

Wand Extensions

Plated Extensions

Wash Wands from Mosmatic. Swiss-Made, High Quality, Stainless Steel Wand Assemblies. Standard with insulated grip and nozzle protector. Straight and bent ends are available. Inlet is 1/4” MPT. Nozzle protectors will accept 1/8” or 1/4” MPT nozzles as noted. Rated to 4000 PSI and 250° F.

Wand Extensions with and without Insulated Grips. Zinc plated steel tubing. Rated to 6000 PSI. Maximum temperature is 300° F. These lance wands are available in 18", 24", 36" or 48" straight end style or 60" & 79" with 45° curved ends. Inlet and outlet are 1/4" MPT (except for ST007-18MF) and require either female nozzles or nozzle holder/protectors shown in this catalog.

D

1/4” MPT Inlet

Bent Style

Part No.

MM 26980 MM 26981 MM 26982 MM 26983 MM 26703 MM 26723 MM 26706 MM 26726 MM 26711 MM 26731 MM 26712 MM 26732

Length

20” Straight 20” Bent End 41” Straight 41” Bent End 20” Straight 20” Bent End 34” Straight 34” Bent End 41” Straight 41” Bent End 50” Straight 50” Bent End

ST003 Wand Only - No Grip

1/4” or 1/8” Outlet

Straight Style

D

D

ST007 Bent Wand with Grip

Outlet

Part No. Extension NP ST007-18 Straight Wand with Grip NP ST007-18MF * Straight Wand with Grip NP ST007-24 Straight Wand with Grip NP ST007-36 Straight Wand with Grip NP ST007-48 Straight Wand with Grip NP ST007-60 Bent Wand with Grip NP ST007-79 Bent Wand with Grip NP ST003-18 Straight Wand, No Grip NP ST003-24 Straight Wand, No Grip NP ST003-36 Straight Wand, No Grip NP ST003-48 Straight Wand, No Grip * 1/8" F Discharge for 1/8" Male Nozzles.

1/8” FPT 1/8” FPT 1/8” FPT 1/8” FPT CALL 1/4” FPT for 1/4” FPT PRICING 1/4” FPT 1/4” FPT 1/4” FPT 1/4” FPT 1/4” FPT 1/4” FPT

Net Ea. $ 5.11 6.96 5.65 6.05 7.62 14.55 14.95 2.25 2.81 3.77 6.31

Stainless Steel Wand Extensions

Galvanized Steel Pipe Extensions with Insulated Grips

1/4" MPT Inlet

Length 18" 18" 24" 36" 47" 60" 79" 18" 24" 36" 48"

D 1/8" FPT

Stainless Steel Wand Barrels are available either insulated or uninsulated. Sizes range from 18" to 84" lengths. All models feature 1/4" MPT inlet and outlet except for #1/4S-18 which has 1/8" FPT outlet and #21762 which has a built-in nozzle protector with 1/4" FPT outlet. Maximum pressures vary from 3000 to 7300 psi. Maximum temperature to 300° F. Wand Extension with grip D

1/4" MPT thread on one end and 1/8" FPT thread on the other. Available in 18" through 27" lengths with a molded GRIP, 6" long. The 36" & 48" lengths have a molded GRIP, 11" long. Pressures to 3000 PSI and Temperatures to 250° F. maximum. For 1/8” MPT or 1/4” FPT nozzles.

Length Grip

Part No. LENGTH 18" 21" 27" 36" 48" Part No. BC 253-18 BC 253-21 BC 253-27 BC 253-36 BC 253-48 Net Ea. $ 9.42 $ 10.80 $ 12.75 $ 15.00 $ 19.85

Galvanized Wand Extensions

1/4" MPT Inlet

1/4" MPT 1/8" FPT

D

Galvanized Steel construction. These uninsulated wands are available from 18" to 48" long. Rated to 3000 psi and 250° F. Ports are 1/4" MPT inlet and 1/4" MPT x 1/8" FPT outlet for 1/8" MPT or 1/4" FPT nozzles. Part No. BC 1/4G-18 Uninsulated Wand BC 1/4G-24 Uninsulated Wand BC 1/4G-27 Uninsulated Wand BC 1/4G-36 Uninsulated Wand

1/4" MPT Inlet

Length 18" 24" 27" 36"

Net Ea. $ 3.51 4.16 4.61 6.36

1/8" FPT

Coated Wand Extensions with built-in tip protectors. Available in blue or black colors and in 18" or 21" lengths. All extensions are internally tapped on discharge end for 1/8" MPT nozzles. Inlet is 1/4" MPT to fit standard spray wands. Heavy urethane coating helps to protect against scratches, gives insulating grip for customer and keeps them looking good. Part No.

LENGTH

BC 719T-18 18" BC 719T-18BK 18" BC 719T-21 21" BC 719T-21BK 21" BC 719T-18R 18”

COLOR

BC 1/4S-18 * 18" Straight No GU 21715 24" Straight No GU 21724A 24" Straight Yes GU 21718 36" Straight No GU 21721A 36" Straight Yes NP ST002-36 36” Straight Yes BC 1/4S-48 48" Straight No GU 21748 48” Straight Yes NP ST002-48 48” Straight Yes NP ST002-48H 48” Straight Yes GU 21719 60" Straight No GU 21759A 60” Straight Yes GU 21725 72" Straight No GU 21728 72” Straight Yes BC 140059 79” Straight Yes GU 21729 84” Straight Yes GU 21726 84" Straight No GU 21762 36" Bent Yes * 1/8" FPT Outlet for 1/8" Male Nozzles.

Max. Maximum PSI Temperature Net Ea.

3000 4000 4000 4100 4100 5800 4100 4000 5800 7300 4100 4100 4000 4000 4100 4000 4000 4100

300° F. 300° F. 300° F. 300° F. 300° F. 300° F. 300° F. 300° F. 300° F. 300° F. 300° F. 300° F. 300° F. 300° F. 300° F. 300° F. 300° F. 300° F.

$ 6.76 7.25 12.45 9.95 14.45 14.80 15.50 18.95 16.00 63.05 18.50 25.50 22.55 26.30 33.50 29.95 25.95 21.95

Double Barrel Extensions

Coated Wand Extensions D

D

Model 21762

Double Barrel Wand Extensions designed to be used with chemical injectors for downstream chemical injection. Side handle grip valve allows for easy change-over from high to low pressure which causes injector to pull soap when needed. Nozzle ports are 1/4" FPT. Inlet is 1/4" MPT. Ends are bent or straight as noted. Model ST53 & ST54 are made by Suttner and have zinc plated barrels. ST53 has knob control in place of the handle on ST54. Soap nozzle is included. YDL Models are made by General/Interpump and feature zinc plated or stainless steel barrels with handles like Model ST54. YDL41 has straight barrels. Control Knob

Model ST53

Net Ea.

Blue $ 5.51 Black 5.51 Blue 8.77 Black 8.77 Red 5.51

Model ST54

Control Handle

Part-No.

Construction Length Max. PSI

NP ST53 * Plated, Bent NP ST54 Plated, Bent NP ST54-48 Plated, Bent NP ST53-72 * Plated, Bent NP ST54-72 Plated, Straight IP YDL41 Plated, Straight IP YDL41B Plated, Bent IP YDL41SSB Stainless, Bent IP ZZDBL72 Plated, Bent

38" 38" 48” 72" 72" 41" 41" 41" 72"

Net Ea.

3600 $ 31.00 3600 34.95 4500 56.85 4500 70.90 4500 77.95 3600 49.25 3600 45.50 3600 51.95 3000 69.85

* Has knob control in place of handle on ST54. DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0074


Foamers • Spray Shield• Nozzle Holder

DEMA

Compressed Air Foam Generators

126

Spray Shield Protect Yourself from Back Spray!

DEMA SERIES 294 COMPRESSED AIR FOAMERS combine detergent concentrate with air and water to produce foam of any consistency. Foam is generated instantly and automatically. Fully adjustable for precise detergentwater proportioning as well as foam dryness. Several DEMA Models which are ideal for trucks, trailers, cars and airplanes are shown below. Foam for horizontal and vertical surfaces. No pumps, pressure tanks, electrical wiring or pre-mixing needed. Makes up to six cubic feet of foam per minute and throws foam up to 25 feet using a straight nozzle.

High Impact Spray Shield is designed to protect operators from backspray of liquids, materials or solids. Great for close-up cleaning jobs like pavement or deck cleaning. Durable, clear plastic pan is designed so the operator can still see the working surface while cleaning. Each spray shield includes 10” plastic pan, inlet quick coupler for 1/4” spray lances and outlet quick coupler for QC spray nozzles (nozzles and lances are not included). Couplers are rated to 5000 PSI.

1/4" NPT air inlet

3/4" GHT threaded foam outlet

Model 294C: Standard Unit. GHT inlet with screw holes for mounting, or mounts directly on 1/2" pipe.

Detergent adjustment screw D

294C

3/4" GHT water inlet 3/8" ID tubing connection for detergent supply Minimum pressure for good foam is 50 PSI of water and 40 PSI of air using 50' of 3/4" ID hose. Injection Capacities Viscosity CPS Oz./Gal.

1

75

220

27 13 10

D

NOTE: These are maximum oz./gal. Detergent consumption may be as little as half these figures depending upon its ability to foam.

Part No.

294CDM

DEMA FOAM GENERATOR UNITS Net Ea.

DE 294C Standard Unit as Shown ................. $ 117.00 DE 294CDM Drum Mounted with Bung Adapter... 129.00 Nozzle Rating - 20-GPM @ 40 PSI Minimum. Part No. Net Ea.

FOAM LANCES

SM A2002

High Impact Spray Shield ................ $ 24.95

Nozzle Holder Suttner Foam Lances are designed to “foam” cleaning agents or disinfectants onto surfaces to be cleaned or sanitized. Used in conjunction with your existing trigger wand and downstream injector. Air pulls into the orifice in the wand handle to mix with the water/chemical flow to create a foam mixture. Stainless nozzle and extension pipe are standard. Inlet is 1/4" FPT. Match air orifice shown to the flow rate of your pump for optimal foam production. Available in either 25" or 48" lengths. Rated to 300° F. Maximum pressure is 900 psi.

Foam Lance Used

Part No.

NP ST722 NP ST723 NP ST724 NP ST725 NP ST726 NP ST727

Unique Nozzle Holder keeps spray nozzles at your fingertips for easy and efficient change-out when necessary. Holder is designed to be securely mounted to the trigger guard of most any trigger spray wand. Plastic construction with stainless steel screws. High strength zip ties are included. Designed for use with QC quick disconnect nozzles. Just push into the holder and nozzles are held firmly in place until you need them. Holds up to (4) nozzles which are not included.

Soap Nozzle Used

Existing Pump Flow

Length

Air Nozzle

1.0 - 2.9 gpm 3.0 - 3.9 gpm 4.0 - 5.0 gpm 1.0 - 2.9 gpm 3.0 - 3.9 gpm 4.0 - 5.0 gpm

25" 25" 25" 48" 48" 48"

Green Yellow Red Green Yellow Red

DULTMEIER SALES

OMAHA, NE (800)

Net Ea.

$ 110.00 109.50 110.00 123.50 123.50 123.50

228-9666

Part No. Net Ea.

SM A2001 DAVENPORT, IA (800)

Nozzle Holder...................................

553-6975

www.dultmeier.com

$ 7.95 E0974


Chemical Dispensing

127

Chemical Dispensing Systems

Blend Centers

These systems promote optimal cleaning product performance as well as being environmentally friendly and cost conscious. You can maximize your use of time, space, money and promote safer working conditions. Model 871 allows one chemical to be dispensed at 4 different concentration levels. This would be the ideal choice if you are using a multi-purpose product and you want one mixture for windows, one for interiors, one for floor maintenance etc. Simply turn the dial to obtain the specific mix ratio that you want. Rated to 4 GPM for filling.

D

Models 874 & 875 allow up to four different chemicals to be dispensed from one system. Simply by turning the dial, one of 4 different products can be dispensed into cleaning pails, bottles or buckets. (i.e. Glass cleaner, tire cleaner, spot remover and multi-purpose cleaner) could all be filled at different mix ratios using this one dispenser. Part No. Products Flow Rate

Dilution Rate Max. Min.

HR 871 HR 874 HR 875

350:1 350:1 128:1

1 4 4

4 GPM 4 GPM 1 GPM

Net Ea.

3:1 $ 142.50 6:1 165.00 3:1 169.50

to meet any blending and dispensing need . . . (3) 633 Valves mounted together.

Ideal for industrial applications where fast, accurate mixing of detergents, disinfectants or chemicals is desired. Blend Centers dispense precise amounts of “mixed” liquids into open containers or bottles from a centralized work station. Dilution Range: 512-1 maximum; 5-1 minimum. Blend ratios and proportion of chemical to water are set by interchangeable, color coded, threaded metering tips.

Series 681 units feature the 633 valve in stainless steel cases. All units easily mount on walls or vertical surfaces. Part No.

Stations

Housing

DE 633 Single Plastic DE 681-1 Single Stainless DE 681-2 Double Stainless DE 681-3 Triple Stainless

D

MODEL 301B is a sturdy, wall-mounted pump. It draws from any size container. Delivers one fluid ounce of liquid chemical with each stroke of pump. Chamber is always filled, assuring fast, accurate service. Body is molded of a corrosion-resistant polypropylene. All working parts are silicone, stainless steel or PVC. Ready to install, with 8' of polyvinyl supply tubing and mounting screws. Part No. Net Ea.

Sure-Measure Dispenser......... $ 23.60

Laundry Detergent Dispenser Laundry Master Chemical Dispensers are designed to dispense 1, 2 or 3 products into laundry machines. Easily Pumps soaps, bleach, etc. into coinoperated or manual machines up to 50 lb. capacity. Peristaltic pumps are triggered by a signal from the machine or by the manual start button. Rates up to 6 oz. per minute mean a consistent mixture every time. One dispenser can feed up to two machines. ABS plastic enclosure features water-tight seal.

Part No.

Number of Products

Net Ea.

OMAHA, NE (800)

228-9666

Water Flow

Net Ea.

4-GPM $ 57.80 4-GPM 80.45 4-GPM 130.00 4-GPM 178.00

HydroMaster Drum Mounted Liquid Proportioner In one simple operation the HydroMaster accurately mixes liquid chemical concentrate with water and dispenses the proportioned solution into any container. It eliminates the mess, guesswork and waste involved with manual mixing.

D

The HydroMaster utilizes the tap water supply and features a standard hose connector. A siphon tube drops through the bung of a chemical drum and draws concentrate through a metering tip to produce the desired dilution ratio. When the drum of concentrate is empty, a swivel adapter allows drum changes without disconnecting the water supply line.

No. 206

Fits 30/55 Gallon Drums

Proven Successful for Mixing: • All-purpose Cleaners • Water-soluble waxes and strippers • Acids and caustics • Sanitizers • Floor and window cleaners • Degreasers & Sanitizers

Design Prevents Water Backflow The siphon tube and the foot valve are designed for one-way flow and prevent back-siphoning of diluted solutions or water into chemical concentrate. Weight is 3 lbs. (5 Lbs. on Model 220.)

Approx. Dilution GPM @ 40 PSI / 1.0 cp Part No. DESCRIPTION 40 PSI Max. Min. Net Ea. HR 204 Low Volume, Wall Mounted ......... 4.4 300:1 5:1 $ 78.95 HR 206 Low Volume Unit Drum/Wall Mtd. . 4.4 300:1 5:1 82.95 HR 208 Low Volume, High Concentration Unit.. 1.6 84:1 1:1 85.90 HR 216 Medium Volume Unit .................... 10 460:1 5:1 95.35 HR 220 High Volume Unit .......................... 18 1100:1 8.1 145.00

DE 830K-1-1 1 $ 195.00 DE 831K-1-1 2 359.00 DE 831K-1-5 3 379.00 DULTMEIER SALES

681-2 Stainless

Model 633 is a single station unit that features a plastic housing. This model can be easily “gang” mounted for multiple products if desired.

Sure-Measure Dispenser

DE 301B

D

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0127


FoamMaster & Dispensing Systems

128

FoamMasters FoamMaster Cleaning Systems automatically dilute cleaning chemicals with water and then use compressed air to generate thick, clinging foam. Foam cleaning allows for the cleaning solution to remain in contact with the soil load surface for extended time period. Three Systems are Available: Wall mounted, portable and drum mounted to meet any foam cleaning requirement. All of these units work on as little as 40 PSI air and 3 GPM water flow. D

Model 865 is a drum mounted unit designed to easily fit onto 30 or 55 gallon drums. Chemical application only, no rinse option is available on this model. Comes with 25’ plastic discharge hose. Dilution range from 5:1 to 128:1. Foam throw, 5’ from end of hose. Model 890 features stainless wall mount enclosure, air regulator, air gauge, rinse valve, 25’ of rubber hose and foam nozzle. Dilution range from 5:1 to 240:1. Foam throw, 15’ to 20’ from end of hose. Model 890C has the same features as Model 890 but also includes a wheeled cart when portability is needed. Air Inlet

Model 890C Cart Mount Model 865 Drum Mount

Water Inlet

25’ Rubber Hose

D

Outlet (plastic hose not shown)

Drum Bung

Part No. HR 865 HR 890 HR 890C

Style Wt. Drum Mount 11 lbs. Wall Mount 21 lbs. Cart Mount 36 lbs.

D

Net Ea. $ 299.00 545.00 1250.00

Model 890 Wall Mount

Chem Dispensing Systems Simplifies cleaning and sanitation operations. Dilutes, dispenses and rinses with the twist of a handle. The perfect choice for any application where cleaning and/or sanitizing is required. Designed for wall mounting. Stainless steel and brass construction. Available in one product (clean & rinse) or two products (clean, sanitize & rinse). Two product unit can easily be set for two different dilution rates. D

Model 918 One Product

Part No. HR 918 HR 919

DULTMEIER SALES

D

Chemical flow rate is 3.5 GPM. Rinse flow rated to 5 GPM. Dilution range from 10:1 to 512:1. Built-in check valve protects against reverse flow. Hose rack is standard but inlet and outlet hoses are not included.

OMAHA, NE (800)

Products One, (Clean/Rinse).............. Two, (Clean/Sanitize/Rinse).

228-9666

Wt. 7 lbs. 8 lbs.

DAVENPORT, IA (800)

Model 919 Two Product

Net Ea. $ 229.00 269.00

553-6975

www.dultmeier.com

E1024


Chemical Foam Units

129

The Ideal Systems for Chemical Foam Washdown and/or Sanitation. For use in agriculture, food and beverage, vehicle cleaning and industrial applications. Available in permanent wall mount systems, portable hand carry or portable cart units. All foamers are designed to combine air pressure, water and chemical mixture to create the type of clinging foam that is required for most cleaning/sanitation situations. All systems are complete and include needle valve for foam control, discharge hose, foam wands and necessary fittings. (Inlet air and water hoses are not included).

Wall Mount Foamer Unit Model 900WC Wall Mount Foamer Unit. Includes: Air driven chemical pump • Air pressure regulator • 50’ of foam hose • Foaming nozzle • Chemical tube • Gasketed control enclosure.

D

Requires 5-10 cfm of air at 40-80 PSI. Creates up to 30 gallons of foam per minute and throws foam to a distance of 25’.

Part No.

DE 900WC

Wt.

Wall Mount Foam Unit

31 lbs.

Model 900WC

Net Ea.

$ 624.00

Hand Pump Up Foamer (2 Gallon)

Model 900-2PU Hand Pump Up Foamer. Easy, hand carry foamer for ease-of-use and portability. Includes: 2 Gallon tank • 3-1/2’ of Hose • Trigger foam wand. Simply fill the tank with chemical water solution and pump up to pressurize. Adjustable needle valve controls foam consistency. Produces approximately 1/2 gallon of foam per minute.

Part No.

DE 900-2PU Pump Up Foam Unit

Wt.

6 lbs.

D

Model 900-2PU

Net Ea.

$ 109.50

Portable Foamer (10 Gallon)

Model 910 Portable Foamer Unit. Wheeled cart with 10 gallon solution tank feeds the air-driven chemical pump. Includes: Air pressure regulator • 20’ of foam hose • Foam nozzle assembly • Air pump • Tank assembly.

Model 910

Requires 5-10 cfm of air at 40-80 PSI.Throws foam to a distance of 25’. Produces approximately 25 gallons of foam per minute. Part No.

DE 910

Wt.

10 Gallon Portable Foam Unit

34 lbs.

D

Net Ea.

$ 766.00

Portable Foamer

Model 925

(25 Gallon)

Model 925 Portable Foamer Unit. Wheeled cart with 25 gallon solution tank feeds the air-driven chemical pump. Includes: Air pressure regulator • 30’ of foam hose • Foam nozzle assembly • Air pump • Tank assembly. Requires 5-10 cfm of air at 40-80 PSI. Throws foam to a distance of 25’. Produces approximately 50 gallons of foam per minute. D

Part No.

Wt.

Net Ea.

DE 925 25 Gallon Portable Foam Unit 59 lbs. $ 928.00 DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0745


FOAMERS

130 Adjustable Foam Lances

High Pressure Foamers

Model 140263 Foam lance with bottle can throw a dense chemical foam up to 20’. Adjustable design allows for user to spray varying distances with a wide or concentrated pattern. Chemical bottle has 32 oz. capacity. Rated to 5.3 GPM and 5000 PSI. Inlet port is 1/4” FPT. 1/4” QC plug and 22mm adapter are also included.

YLS12T & YLS31T with tank D

D

YLS12 Foamers

These unique foamers can be attached to your discharge gun to apply foamed chemicals downstream from your high pressure pump. Rated to a maximum of 2900 PSI. Foam supply can be easily changed with the adjustment knob. Features: Rust-proof construction • chemical resistant material • filtered chemical bottle.

Model 140289 Foam lance without chemical bottle. Simply put tubing and foot valve into your chemical pail or drum. Kit includes foam lance, 30’ tubing, foot valve and (3) orifices for 3.0, 4.0 or 5.6 GPM pumps. Rated to 5.6 GPM, 5000 PSI and 140° F. Inlet is 1/4” FPT.

Inlet

YLS12 is a foamer with an injector barb inlet for hose or tubing, not tank. YLS12T & YLS31T are the same as YLS12 but with 1 quart tank. Specifications: Maximum temperature of 140° F. • Weight is approximately 1-lb. • Materials of construction are plastic, brass, stainless steel and Buna-N. • Tank is 1 quart capacity. Inlet is 1/4" FPT. Maximum Maximum Part No. Pressure GPM

IP YLS12 Foamer WITHOUT Tank IP YLS12T Foamer WITH Tank IP YLS31T Foamer WITH Tank

2900 PSI 2900 PSI 2300 PSI

6.50 6.50 5.30

140263 Foamer with Tank

Chemical Barb D

Net Ea.

$ 57.85 70.50 49.40

140289 Foamer without Tank

D

Maximum Maximum Part No. Pressure GPM

ProFoam Foamer - Low Pressure

MV 140263 Foamer WITH Tank MV 140289 Foamer WITHOUT Tank

DEMA Hand-Held Bottle Foamer dispenses foaming degreasers and sanitizers on a variety of surfaces. Ideal for use in car washes, food service areas, quick lube bays etc. Easily attaches to standard garden hose with city water pressure. Produces excellent foam quality with good distance, (10' throw at 40 psi inlet water pressure). Spray gun and quick connect fitting are standard. Bottle has 32 oz. capacity.

5000 PSI 5000 PSI

5.3 5.6

Net Ea.

$ 50.95 75.95

Foamer & Tank Foamer Unit from Suttner can be adjusted for vertical or horizontal spray pattern. Ideal for industry, agriculture, institutional cleaning and food processing. Includes metering valve for (5) chemical mixture settings. Easy-to-fill, wide mouth, 32 oz. bottle. Plastic and stainless construction for corrosion-resistance. Unique design cuts chemical consumption by up to 50% over other foamers on the market. Rated to 3600 PSI, 2.5 GPM and 176° F.

Maximum Part No. Pressure

NP ST73

D

D

Maximum GPM

Net Ea.

2.5

$ 46.60

Foamer and Tank 3625 PSI

Part No. Net Ea.

DE 289 ProFoam Bottle Foamer $ 54.20

Call Us For All Your FOAMER Needs! OMAHA, NEBRASKA

DAVENPORT, IOWA

1-800-228-9666

1-800-553-6975

FAX: 1-402-333-5546

FAX: 1-563-386-5448

Call Us For All Your Car Wash & Truck Wash Needs!

http://www.dultmeier.com DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0109


Sewer / Jetter Nozzles

131

Typical Flow Rates & Pipe Size

Sewer / Jetter Nozzles are ideal for use with flexible hoses or rigid lances for cleaning sanitary and storm sewer lines, plumbing lines or drains in commercial and residential applications. Available in (4) different styles. Stock nozzles offer the most common forward and rear angle jets for efficient flushing, penetration or pushing. Most nozzles can be special drilled to meet your specific applications. All nozzles shown are Stainless Steel construction with Female Pipe Threads.

Hose Size 1/8” I.D. 1/4” I.D. 3/8” I.D. 1/2” I.D. 3/4” I.D. 1” I.D. 1-1/4” I.D.

Nozzle sizes shown are the total of all jet openings. Nozzle sizes are also the flow rate at 4,000 PSI. Higher or lower pressures will increase or decrease flow rates. We will be glad to help with sizing as needed.

Laser-Penetrating Nozzles Laser-Penetrating Nozzles usually feature 3 to 4 back facing jets and 1 forward cutting jet. Ideal for the first pass through a blockage. Ideal for cutting with some flushing. Best choice for the 1st step in the cleaning process. RN Series

Cornering-Pusher Nozzles usually features a single jet at 90 degrees to the rear facing jets. This helps to force the nozzle through tight bends and turns. Best when used after or in conjunction with Laser nozzles. Part No.

FPT Nozzle Maximum Inlet Size PSI

Net Ea.

D

ST37 & ST50 Series

Part No.

RNH Series

Net Ea.

All Nozzles can be Specially Drilled to Meet Your Flow & Pressure Needs!

(800) 228-9666

Net Ea.

$ 11.95 11.95 22.95 22.95 30.95 30.95 30.95 37.95 37.95 37.95 37.95

SJ Series

TR Series

DULTMEIER SALES • OMAHA, NE

FPT Nozzle Maximum Inlet Size PSI

Rotating Nozzles

Ram-Pusher/Flusher Nozzles

AA TRS55S1F 1/8” 5.5 4,000 $ 10.35 AA TR45R 1/4" 4.5 4,000 11.95 AA TR55RR 1/4” 5.5 4,000 11.95 NP RNH258 1/4” 8 10,000 32.95 NP RNH2512 1/4” 12 10,000 32.95 NP RNH374 3/8” 4 10,000 33.95 NP RNH376 3/8” 6 10,000 33.95 NP RNH378 3/8” 8 10,000 33.95 NP RNH3712 3/8” 12 10,000 33.95 NP RNH508 1/2” 8 10,000 41.95 NP RNH5010 1/2” 10 10,000 41.95 NP RNH5015 1/2” 15 10,000 41.95 NP RNH5020 1/2” 20 10,000 41.95 NP RNH7520 3/4” 20 10,000 77.50 NP RNH7530 3/4” 30 10,000 77.50 NP RNH7540 3/4” 40 10,000 77.50 NP RNH7560 3/4” 60 10,000 77.70 NP RNH10040 1” 40 10,000 125.00 NP RNH10060 1” 60 10,000 125.00 NP RNH10080 1” 80 10,000 125.00

RNHC Series

Rotating Nozzles have the best design for cleaning after penetrating and flushing nozzles have been used. Utilizes offset jets on a free spinning rotor to provide 360 degree coverage. Standard with Ram/Flusher design but laser front hole is also available. ST37 & ST50 Series are lower priced economy nozzles.

Ram-Pusher/Flusher Nozzles usually feature 4 to 6 rear facing jets and no forward jet. Ideal for pushing through blockage and flushing as nozzle is pulled back. Best performance is after the Laser Nozzle is used to cut the blockage first.

FPT Nozzle Maximum Inlet Size PSI

TC Series

AA TC45CC 1/4" 4.5 4,000 AA TC55C 1/4” 5.5 4,000 NP RNH25C8 1/4” 8 10,000 NP RNH25C12 1/4” 12 10,000 NP RNH37C6 3/8” 6 10,000 NP RNH37C8 3/8” 8 10,000 NP RNH37C12 3/8” 12 10,000 NP RNH50C8 1/2” 8 10,000 NP RNH50C10 1/2” 10 10,000 NP RNH50C15 1/2” 15 10,000 NP RNH50C20 1/2” 20 10,000

NP ST47-4 1/8" 4.5 4,000 $ 3.95 NP ST47-5 1/8” 5.5 4,000 3.95 NP ST47-6 1/8” 6.5 4,000 3.95 NP ST49-5 1/4” 4.5 4,000 5.25 NP ST49-6 1/4” 5.5 4,000 5.25 NP ST49-8 1/4” 6.5 4,000 5.25 NP ST49-12 1/4” 7.5 4,000 10.95 NP ST49-14 1/4” 8 4,000 5.25 NP ST49-15 1/4” 12 4,000 5.25 NP ST494 3/8” 4.5 4,000 6.25 NP ST491 3/8” 5.5 4,000 6.25 NP ST499 3/8” 6.5 4,000 6.25 NP ST492 3/8” 8.0 4,000 6.25 NP ST493 3/8” 12 4,000 6.25 NP ST497 3/8” 14 4,000 21.75 NP RN508 1/2” 8 10,000 42.85 NP RN5010 1/2” 10 10,000 42.85 NP RN5015 1/2” 15 10,000 42.85 NP RN5020 1/2” 20 10,000 42.85 NP RN7520 3/4” 20 10,000 77.95 NP RN7530 3/4” 30 10,000 77.95 NP RN7540 3/4” 40 10,000 77.95 NP RN7560 3/4” 60 10,000 77.95 NP RN10040 1” 40 10,000 125.00 NP RN10060 1” 60 10,000 125.00 NP RN10080 1” 80 10,000 125.00

Part No.

Flow Rates 1 - 2 GPM 2 - 4 GPM 4 - 6 GPM 8 - 20 GPM 20 - 60 GPM 30 - 70 GPM 70 - 120 GPM

Cornering-Pusher Nozzles

ST Series

Part No.

Pipe Diameter 1” to 2” 2” to 3” 2” to 4” 4” to 6” 4” to 8” 4” to 10” 5” to 12”

FPT Nozzle Maximum Inlet Size PSI

Net Ea.

NP ST37-5 1/8" 5 7,300 $ 30.50 NP ST37-7 1/8” 7 7,300 30.50 NP ST50-45 1/4” 4.5 4,000 9.20 NP ST50-55 1/4” 5.5 4,000 23.95 NP ST50-8 1/4” 8 4,000 23.95 NP ST51-85 3/8” 8.5 4,000 9.15 NP SJ2512 1/4” 12 10,000 155.00 NP SJ376 3/8” 6 10,000 155.00 NP SJ378 3/8” 8 10,000 155.00 NP SJ3712 3/8” 12 10,000 155.00 NP SJ508 1/2” 8 10,000 247.00 NP SJ5010 1/2” 10 10,000 247.00 NP SJ5015 1/2” 15 10,000 247.00 NP SJ5020 1/2” 20 10,000 247.00 NP SJ7520 3/4” 20 10,000 265.00 NP SJ7530 3/4” 30 10,000 265.00 NP SJ7540 3/4” 40 10,000 265.00 NP SJ7560 3/4” 60 10,000 265.00 NP SJ10040 1” 40 10,000 455.00 NP SJ10060 1” 60 10,000 455.00 NP SJ10080 1” 80 10,000 455.00

Drain Cleaning Nozzle High Flow Drain Cleaning Nozzle. Rated to 16 GPM at up to 3000 PSI. Designed to clean pipes from 1-1/2" to 5" diameter. Ram design has orifices at 45° angles pointing backward which propels the nozzle forward when in operation and cleans as the nozzle is pulled back. 3/8" Male Pipe Thread.

— High Flow —

Part No.

Max. Pressure

Max. GPM

IP NT16 3000 •

www.dultmeier.com

• DAVENPORT, IA

Net Ea.

16 $ 92.25

(800) 553-6975

E0879


Cleaning Nozzles

132

CLEANING NOZZLES 300 to 4000 PSI

High Quality, High Impact Spray Nozzles for wands, arches, conveyor systems and anywhere high pressure washing or rinsing is needed. Available from 0 degree solid stream to 110 degree flat fan patterns. Stainless steel construction rated between 300 and 4000 PSI. Internal guide vane is available on some nozzle types to provide maximum spray integrity. Available in 1/8” male, 1/4” female and 1/4” quick coupler styles as noted below.

Nozzle Types

D D

Solid Stream Nozzle

D

MEG 1/4” & 1/8” Male

VeeJet HVVSS Series 300 stainless steel nozzles create a very precise pattern from 300 to 1000 PSI. Solid stream to 110 degree wide patterns are available. 1/8” male and 1/4” males nozzles are available from #1 through #15 orifices. Example: H1/4VVSS2506 is 1/4” male thread, 25 degree pattern, #6 orifice.

Flat High Pressure Even Spray Stabilizer Vane provides high & uniform impact capabilities. Even spray pattern eliminates the need to overlap patterns from adjacent nozzles.

1/4” WEG Female

WashJet MEG Series 400 hardened stainless steel nozzles are rated to 3000 PSI. Available with or without stabilizer vanes. Solid stream to 65 degree wide patterns are available. 1/8” MEG (Male) Nozzles are available for #1 through #20 orifices. Male threads only. Example: 1/8MEG0002 is 1/8” MPT (male) thread, zero stream, #2 orifice. (ADD VA at end of number if internal vane is required). 1/4” MEG (Male) or 1/4”WEG (Female) nozzles are available from #2 through #80 orifices. Example: 1/4WEG4004 is 1/4” female thread, 40 degree pattern, #4 orifice. (ADD VA at end of number if internal vane is required). Part No. SS 1/8MEGxxxx SS 1/8MEGxxxxVA SS 1/4MEGxxxx SS 1/4MEGxxxxVA SS 1/4WEGxxxx SS 1/4WEGxxxxVA

Nozzle Type Max. PSI Net Ea. 1/8” Male, No Vane 3000 $ 3.75 1/8” Male, With Vane 3000 3.95 1/4” Male, No Vane 3000 3.95 1/4” Male, With Vane 3000 4.63 1/4” Female, No Vane 3000 7.60 1/4” Female, With Vane 3000 8.25

5% Discount on 20 Nozzles of One Size 10% Discount on 100 Assorted Nozzles

Stabilizer Vane

IMEG Series 400 hardened stainless steel nozzles are rated to 4000 PSI. Unique design offers at least 25% more impact than regular MEG nozzles at comparable pressures. Solid stream to 65 degree wide patterns are available.

IMEG 1/4” & 1/8” Male

Part No. SS H1/8VVSSxxxx SS H1/4VVSSxxxx SS H1/4USSxxxx

Nozzle Type 1/8” Male 1/4” Male 1/4” Male

Max. PSI 1000 1000 1000

HVVSS & HUSS VeeJet

Net Ea. $ 5.90 6.33 7.13

5% Discount on 20 Nozzles of One Size or 10% Discount on 100 Assorted Nozzles

Nozzle Patterns & Sizes 0 Degree, Solid Stream nozzles are available from #2 through #20 orifices in 1/8” MPT male and #2 through #80 orifices in 1/4” MPT (male) or 1/4” FPT (female) styles. Good choice for aggressive pressure washer and industrial cleaning. 5 Degree nozzles are available from #2 through #9 orifices in 1/8” MPT male and #2 through #30 orifices in 1/4” MPT (male) or 1/4” FPT (female) styles. Good choice for aggressive pressure washer and industrial cleaning. 15 Degree nozzles are available from #1 through #15 orifices in 1/8” MPT (male) and #1 through #60 orifices in 1/4” MPT (male) or 1/4” FPT (female) styles. Good choice for pressure washer, industrial cleaning, self serve, automatic and conveyor car washes. 25 Degree nozzles are available from #2 through #15 orifices in 1/8” MPT (male) and #2 through #60 in 1/4” MPT (male) or 1/4” FPT (female) styles. Good choice for pressure washer, self-serve, automatic and conveyor wash and industrial cleaning applications. Most popular self-serve wash pattern. 40 Degree nozzles are available from #2 through #12 orifices in 1/8” MPT (male) and #1 through #60 in 1/4” MPT (male) or 1/4” FPT (female) styles. Good choice for arches, high pressure automatics, conveyor wash and industrial cleaning applications. 50, 65 and 80 Degree nozzles are available in limited sizes, call for details. Good choice for conveyor wash and industrial cleaning applications.

1/8” IMEG (Male) Nozzles are available from #3 through #8 orifices. 1/4” IMEG (Male) Nozzles are available from #2 through #10 orifices Part No. SS 18IMEGxxxx SS 18IMEGxxxxVA SS 14IMEGxxxx SS 14IMEGxxxxVA

Nozzle Type Max. PSI Net Ea. 1/8” IMEG, No Vane 4000 $ 3.95 1/8” IMEG, With Vane 4000 4.35 1/4” IMEG, No Vane 4000 4.10 1/4” IMEG, With Vane 4000 4.55

5% Discount on 20 Nozzles of One Size 10% Discount on 100 Assorted Nozzles

QCMEG Series 400 hardened stainless steel nozzles are rated to 4000 PSI. This series features 1/4” male quick coupler inlet and color coded caps. All QCMEG nozzles also come with internal stabilizer vanes. Solid stream to 40 degree wide patterns are available. 5% Discount on 20 Nozzles of One Size and QCMEG 10% Discount on 100 1/4” Quick-Connect Assorted Nozzles Part No. Nozzle Type Max. PSI Net Ea. SS QCMEGxxxx 1/4” Quick Coupler 4000 $ 3.95 SS QCEM2540 1/4” Brass Soap Nozzle 300 4.05 Note: Nozzle colors are based on pattern and not orifice numbers. Spray Angles: 0° = Red 15° = Yellow 25° = Green 40° = White

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0084


Spray Nozzles

133 Stainless Nozzle Packs

Stainless/Ceramic Wash Nozzles

Hardened Stainless

Convenient Nozzle Packs for many popular High Pressure Automatics. Now you can replace all of your nozzles at one time. No more guessing which nozzles need to be replaced. All nozzle packs include the correct orifice sizes and patterns for the automatic shown. Hardened, stainless steel construction is standard in all kits.

High Pressure, Stainless Steel Nozzles with nearly Diamond-hard, Ceramic Inserts. Lasts up to 10 times the life of regular stainless steel. This means less down time and less nozzle change out. The wear characteristics are ideal for use with Reclaim water. Easily handles pressures to 5,000 PSI. Threads are 1/4” MPT. Patterns from 0 to 40 Degree in a wide range of orifice sizes. (Nozzle packs for touchless automatics also available).

D

Part No.

Automatic

IP 105140 HY 105140UC HY 107198 HY 107180 HY 107185 IP 105144 IP 105145 IP 105154 IP 105167 IP 105168 IP 105169

PDQ Laser 4000 Arch ............... 18 $ 51.40 Laser 4000 Undercarriage......... 12 46.10 Belanger Vector Rapid Wash..... 32 119.50 Wash World Velocity Arch.......... 19 71.70 Wash World Undercarriage........ 11 42.20 D&S 5000 Gantry....................... 32 48.50 D&S 5000 Blaster....................... 24 36.10 Futura ........................................ 30 74.85 Oasis 9120 Windvan.................. 24 69.70 Oasis Undercarriage.................. 27 83.40 Oasis Rocker Panel.................... 10 29.75

Total Nozzles

Net Ea.

Stainless/Ceramic Nozzle Packs Replacement Nozzle Packs featuring long life, stainless steel/ceramic nozzles. Diamond-hard ceramic design lasts up to 10 times as long as regular stainless steel. Changing nozzles less means lower down time and less labor. An ideal choice for use with reclaim water. All packs include the correct orifice sizes and patterns for the automatics shown.

D

Part No.

Automatic

HY 107140 HY 107195 HY 107190 HY 107192

PDQ Laser 4000 Arch ............... 18 $ 169.00 Belanger Vector Rapid Wash...... 32 293.00 Wash World Velocity Arch.......... 19 177.50 Wash World Undercarriage........ 11 102.50

Total Nozzles

Net Ea.

Steam Nozzles Brass

D

Nozzles for use with steam cleaners and saturated steam. Rated to 1450 PSI. Inlet is 1/4". Orifice size is 06. Part No.

Net Ea.

IP YSTN14F Steam Nozzle...... $ 6.40

Nozzle Removal Tools Remove Nozzles Easily!

Nozzle Size 1/8" Nozzles 1/4" Nozzles

Part No. Pattern Orifice Net Ea. TW S140002 0° 02 $ 9.85 TW S141502 15° 02 9.85 TW S142502 25° 02 9.85 TW S144002 40° 02 9.85 TW S140003 0° 03 9.85 TW S141503 15° 03 9.85 TW S142503 25° 03 9.85 TW S144003 40° 03 9.85 TW S140004 0° 04 9.85 TW S141504 15° 04 9.85 TW S142504 25° 04 9.85 TW S144004 40° 04 9.85 TW S1400045 0° 045 9.85 TW S1415045 15° 045 9.85 TW S1425045 25° 045 9.85 TW S1440045 40° 045 9.85 TW S140005 0° 05 9.85 TW S141505 15° 05 9.85 TW S142505 25° 05 9.85 TW S144005 40° 05 9.85 TW S1400055 0° 055 9.85 TW S1415055 15° 055 9.85 TW S1425055 25° 055 9.85 TW S1440055 40° 055 9.85 TW S140006 0° 06 9.85 TW S141506 15° 06 9.85 TW S142506 25° 06 9.85 TW S144006 40° 06 9.85 TW S1400065 0° 065 9.85 TW S1415065 15° 065 9.85 TW S1425065 25° 065 9.85 TW S1440065 40° 065 9.85 TW S140007 0° 07 9.85 TW S141507 15° 07 9.85 TW S142507 25° 07 9.85 TW S144007 40° 07 9.85 TW S140008 0° 08 9.85 TW S141508 15° 08 9.85 TW S142508 25° 08 9.85 TW S144008 40° 08 9.85 TW S140010 0° 10 9.85 TW S141510 15° 10 9.85 TW S142510 25° 10 9.85 TW S144010 40° 10 9.85 TW S140012 0° 12 9.85 TW S141512 15° 12 9.85 TW S142512 25° 12 9.85 TW S144012 40° 12 9.85

Stainless vs. Ceramic Nozzle

These handy tools are designed for removing and replacing 1/8" or 1/4" high pressure nozzles. No other tools are needed. This T-handle tool fits easily in your hand. Ideal for removing nozzles from spray wands, arches, automatic arms, etc.

Part No. BC 120 Nozzle Tool BC 126 Nozzle Tool

D

The photo at right compares a stainless steel nozzle and ceramic nozzle.When comparing the photos, you can see the wear on the stainless steel nozzle after 50 hours of use, while the ceramic nozzle shows no visible signs of wear.

D D

Net Ea. $ 7.15 7.15

DULTMEIER SALES • OMAHA, NE

Standard MEG Nozzle

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0997


Spray & Misting Nozzles "SPRAYFLEX" Adjustable Nozzle NOZZLE MODEL

Misting Nozzles

D

Misting Spray Nozzles are designed to create an ultra-fine, atomizing mist. Typical applications include mist cooling, dust suppression, fogging, humidification, fire protection and many more. Poly/Nylon nozzles with ceramic orifices are designed for long wear life. Built-in check valve prevents dripping when not in use. Threads are 1/4” MPT. Rated to 1000 PSI.

SPRAY-FLEX NOZZLE PERFORMANCE TABLE Water At 70° F. (22 C.) NOZZLE CAPACITY (GPM) AT PUMP PRESSURE (PSI)

UMBER 300 N 400 500 600 700 800 1000 1200 1500 2000 2X40 1.1 1.3 1.4 1.6 1.7 1.8 2.0 2.2 2.45 2.85 2X45 1.2 1.4 1.6 1.7 1.9 2.0 2.3 2.45 2.75 3.2 2X50 1.4 1.6 1.8 1.9 2.1 2.2 2.5 2.75 3.05 3.55 2X55 1.5 1.7 1.9 2.1 2.3 2.5 2.8 3.05 3.40 3.9 2X60 1.6 1.9 2.1 2.3 2.5 2.7 3.0 3.3 3.7 4.25 2X65 1.8 2.1 2.3 2.5 2.7 2.9 3.3 3.55 4.0 4.6 2X70 1.9 2.2 2.5 2.7 2.9 3.1 3.5 3.85 4.3 4.95 2X75 2.1 2.4 2.9 3.1 3.1 3.4 3.7 4.1 4.6 5.3 2X80 2.2 2.5 2.8 3.1 3.4 3.6 4.0 4.4 4.95 5.65 2X85 2.35 2. 7 3.0 3.3 3.6 3.8 4.2 4.65 5.25 6.05 2X90 2.5 2.9 3.2 3.5 3.8 4.0 4.5 4.95 5.55 6.2 2X95 2.6 3.0 3.35 3.7 4.0 4.25 4.75 5.20 5.80 6.7 2X100 2.7 3.2 3.5 3.9 4.2 4.5 5.0 5.5 6.15 7.1

D

31943

• Fogging

• Mist Cooling

• Humidification

• Moisture Control

• Fire Protection

• Dust Suppression

• Disinfection

• Deodorizing

• Special Effects

Nozzle Performance Chart GPM Nozzle Flow at Various Pressures Model

Free Pass Dia. (mm)

400 PSI 25 BAR

600 PSI 40 BAR

800 PSI 55 BAR

1000 PSI 70 BAR

31943 .025 .015 .018 .022 .025 31944 .030 .035 .042 .048 .055

D

31945 .050 .050 .060 .070 .080

D

GPH Nozzle Flow at Various Pressures

Part No. Orifice Pattern Color * Net Ea. TW 2E25 02 25° Orange $ 2.01 TW 2E40 02 40° Orange 2.01 TW 2E65 02 65° Orange 2.01 TW 3E00 03 0° Red 2.01 TW 3E25 03 25° Red 2.01 TW 3E40 03 40° Red 2.01 TW 3E65 03 65° Red 2.01 TW 3E80 03 80° Red 2.01 TW 4E00 04 0° Light Blue 2.01 TW 4E25 04 25° Light Blue 2.01 TW 4E40 04 40° Light Blue 2.01 TW 4E65 04 65° Light Blue 2.01 TW 4E80 04 80° Light Blue 2.01 TW 5E00 05 0° Yellow 2.01 TW 5E25 05 25° Yellow 2.01 TW 5E40 05 40° Yellow 2.01 TW 5E65 05 65° Yellow 2.01 TW 5E80 05 80° Yellow 2.01 TW 6E00 06 0° Lime Green 2.01 TW 6E25 06 25° Lime Green 2.01 TW 6E40 06 40° Lime Green 2.01 TW 6E65 06 65° Lime Green 2.01 TW 6E80 06 80° Lime Green 2.01 TW 7E00 07 0° Brown 2.01 TW 7E25 07 25° Brown 2.01 TW 7E40 07 40° Brown 2.01 TW 7E65 07 65° Brown 2.01 TW 8E25 08 25° Moss Green 2.01 TW 8E40 08 40° Moss Green 2.01 TW 8E65 08 65° Moss Green 2.01 TW 8E80 08 80° Moss Green 2.01 TW 10E00 10 0° Royal Blue 2.01 TW 10E25 10 25° Royal Blue 2.01 TW 10E40 10 40° Royal Blue 2.01 TW 10E65 10 65° Royal Blue 2.01 TW 10E80 10 80° Royal Blue 2.01 TW 20E25 20 25° Olive Green 2.01 TW 20E40 20 40° Olive Green 2.01 TW 20E65 20 65° Olive Green 2.01 TW 20E80 20 80° Olive Green 2.01 TW 30E25 30 25° Red 2.01 TW 30E40 30 40° Red 2.01 TW 30E65 30 65° Red 2.01 TW 30E80 30 80° Red 2.01 TW 40E65 40 65° Light Blue 2.01 TW 40E80 40 80° Light Blue 2.01 *Note: Extra 10 % discount when ordering 25 nozzles of one size, 15% on 100+ DULTMEIER SALES • OMAHA, NE

Ultra-Fine Atomizing Mist

$ 20.55

Plastic Spray Nozzles Plastic Spray Nozzles for increased life and lower cost. The perfect choice for rinse arches, soap arches, wash down, cooling, dust suppression, etc. Excellent wear life. Chemical and Temperature Resistant. 1/4" MPT is standard. These PVDF nozzles will actually out-wear stainless steel nozzles! Maximum temperatures to 300° F. Maximum pressures to 600 psi. Color-coded by flow rate.

31945

31944

Typical Applications

ADJUSTABLE “SPRAYFLEX” NOZZLES are infinitely adjustable from a solid stream to a flat 80° pattern. Adjustment can be made through the whole range while the pump is running. Since flow is through the center of the nozzle, there is no pressure loss. Simple to adjust. Twist cap to widen or narrow angle pattern. Body is brass. Internal nozzle and deflector are Stainless Steel. Cap is molded polyester. Inlet is 1/4" FPT. Maximum pressure is 2000 PSI. Maximum temperature is 180° F. SELECT THE APPROPRIATE NOZZLE SIZE FROM CHART BASED ON THE PRESSURE AND GPM AVAILABLE FROM YOUR PUMP. Part No. Net Ea.

ALL SIZES (SPECIFY)

D

D

SELECT THE APPROPRIATE NOZZLE SIZE FROM CHART BASED ON THE PRESSURE AND GPM AVAILABLE FROM YOUR PUMP

HY 2X40 thru 2X100

134

(800) 228-9666

Model

Nozzle Size

400 PSI 25 BAR

600 PSI 40 BAR

800 PSI 55 BAR

1000 PSI 70 BAR

31943 .025 .090 1.08 1.32 1.44 31944 .030 2.10 2.52 2.88 3.30 31945 .050 3.0 3.6 4.2 4.8

Part No.

Description

CC 31943 CC 31944 CC 31945

.025 Misting Nozzle .030 Misting Nozzle .080 Misting Nozzle

Color

Net Ea.

Red $ 10.55 Green 10.55 Purple 10.55

Misting Nozzles

D

Hypro Misting Nozzles produce 50 micron droplets making them ideal for evaporative cooling and humidification. Can also be used with disinfectants, odor control and dust suppression. Corrosion-resistant construction. Rated to 150 PSI. Standard AF Nozzles are available in a variety of sizes. AFD Nozzles feature anti-drip design but only in a few sizes. Built-in strainers are available on request. 1/8” MPT threads are standard.

AF-Hollow Cone 1/8” MPT Nozzles

US gal/hr @ pressure (PSI) Part No. Color Spray Angle 40 60 75 100 150 Net Ea. TW 301AF0.4-65 White 65 0.48 0.59 0.66 0.76 0.93 $ 1.78 TW 301AF0.7-80 Gray 80 0.72 0.88 0.99 1.14 1.39 1.20 TW 301AF0.7-80W White 80 0.72 0.88 0.99 1.14 1.39 1.20 TW 301AF1.2-105C Cream 105 1.20 1.47 1.64 1.90 2.32 1.20 TW 301AF1.6-100 Blue 100 1.68 2.06 2.30 2.66 3.25 1.20 TW 301AF5.0-70 Yellow 70 5.00 6.12 6.85 7.91 9.68 1.20 AFD-Hollow Cone 1/8” MPT Anti-Drip Nozzles

US gal/hr @ pressure (PSI) Part No. Color Spray Angle 40 60 75 100 150 Net Ea. TW 301AFD0.7-80 Gray 80 0.72 0.88 0.99 1.14 1.39 $ 2.44 TW 301AFD1.2-105 Cream 105 1.20 1.47 1.64 1.90 2.32 2.44 TW 301AFD1.6-100 Blue 100 1.68 2.06 2.30 2.66 3.25 2.44

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0829


Nozzles • Coil Cleaning • Sludge Pumps

135

Inline High Pressure Filters

A complete pump, hose and tank package for use with Coil Cleaning Acids. Ideal for descaling coils on water heaters, hot water generators and heat exchangers. This unit has the Little Giant Model 2-MD-SC magnetic-driven pump and motor unit with leak-proof, seal-less design.

High Pressure Filters for protecting rotating or oscillating nozzles from foreign particles. Recommended for extending the life on these nozzles by all nozzle manufacturers. Inlet ports are either 1/4" MPT, 1/4" FPT or 1/4" quick coupler fitting. Rated to 8 gpm and 350° F. All are standard with 100 mesh stainless screens. Model 100562 and 100579 are brass construction. Model 100560 is stainless construction.

GKPK-SC

100560

Net Ea.

IP 100562 IP 100579 IP 100560

$ 8.92 8.92 11.15

5000 PSI 5000 PSI 5500 PSI

Features Include: Polypropylene head & im­peller • Nitrile o-ring • Rated to 150° F. • Maximum viscosity is 100 SSU • Voltage is 115 Volt AC, 1 Phase • Overall dimensions are 8" x 11" x 17".

D

D

Maximum Part No. Inlet x Outlet Pressure

1/4" M x M 1/4" F x M 1/4" QC x 1/4"M

Coil Cleaning Unit

Inlet

100562

Package Includes: 5 gallon tank with cover as well as tubing and connec­tion fittings. Max. Maximum

Part No. Flow Pressure WT Net Ea. GJ GKPK-SC Coil Cleaning Package 8.5 GPM 6.3 PSI 10 lbs. $ 266.50

Turbo Filter

Sludge Pump Systems

Designed to protect Rotating or Oscillating Nozzles from foreign particles. Standard with 100 mesh filter. Inlet is 1/4" FPT, outlet is 1/4" MPT. Length is 2". Maximum temperature is 250° F. Maximum pressure is 5000 psi. Maximum Flow is 12 GPM. Maximum Part No. Inlet x Outlet Pressure

GU 22175 GU 22174

Net Ea.

Suttner Sludge Pumps for vacuuming liquids and sludge. A great accessory for any pressure washer. Can be used for cleaning floors or even car wash pits (after agitating). Uses pressure from your car wash or pressure washer pump and makes it work like a sump or trash pump. (Empties to within 1/2" of bottom.)

D

$ 10.75 3.66

1/4" F x 1/4" M 5100 PSI Replacement Screen...........

Available with either 15' or 25' discharge hoses. Match the nozzle number shown to the nozzle used on your current system. Discharge ratio is approximately 1:11 based on clean water. Ratio will vary depending on pressure, flow, viscosity. Inlet is 1/4" quick coupler.

Turbo Strainer

QC Inlet

D

Standard with 80 Mesh Screen

D

High Pressure Strainer for Turbo Nozzles. Protects rotating nozzles from damaging foreign debris. Rated to 8 gpm and 5000 psi. Maximum temperature is 200° F. ST909 is 1/4" quick coupler Inlet x 1/4" MPT Outlet.

Inlet hose from wash unit is not included

ST910 is 1/4" MPT x 1/4" FPT. D

Example: 4 gpm in

D

ST909

48 gpm out

PVC Discharge hose is 1-1/2" & available in 15 ft. or 25 ft. lengths High Pressure nozzle 4.0, 5.0, 6.0 (See Nozzle Charts)

ST910

Maximum Part No. Inlet x Outlet Pressure

Net Ea.

NP ST909 1/4" QC x 1/4" MPT 5000 PSI NP ST910 1/4" FPT x 1/4" MPT 5000 PSI

$ 10.80 9.36

Part No.

Adjustable Nozzle Holders These nozzle holders are the perfect choice for cleaning hard-to-reach places like gutters or enclosed containers. Stainless steel construction allows for 270 degree adjustment. Pressure locks holder in place when in use. Maximum pressures to 5000 PSI and temperatures to 300° F. Ports are 1/4” FPT. Rated to 10 GPM. Part No.

10 GPM

ST51N

15' 25' 15' 25' 15' 25'

Net Ea.

$ 80.70 95.60 80.70 95.60 80.70 95.60

Dual Nozzle Holders Ports

Net Ea.

1/4” FPT $ 29.80

Adjustable Nozzle Holders D

Discharge Hose

D

Flow Rate

NP ST330

Orifice

NP ST36-4015 4.0 NP ST36-4025 4.0 NP ST36-5015 5.0 NP ST36-5025 5.0 NP ST36-6015 6.0 NP ST36-6025 6.0

Adjustable Nozzle Holders. Change the pressure of your spray with a turn of the grip. Works as a “Hi-Lo” noz­zle for downstream soap injection. Turning the grip directs flow through or around the orifice to increase or decrease pressure. (1/4" MPT Nozzle must be pur­chased separately.) Ports are 1/4" FPT. Maximum temperature is 300° F. Part No.

GPM

PSI

Designed for use with two spray nozzles for high and low pressure. Dual nozzle selector enables the operator to use a downstream injector for corrosive chemical injection. Simple right to left turn rotates ball to open high or low pressure passage. Inlet port is 1/4" FPT. Nozzle ports are 1/4" FPT. Part No.

GPM

PSI

D

32149 ST56

Net Ea.

CC 32149 10.5 2900 $ 7.50 NP ST56 8 3600 16.25

D

Net Ea.

NP ST51N Suttner 8 3600 $ 14.00 IP ST55N General 8 4000 10.20 DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0085


Rotating Spray Nozzles

136

4500 PSI Turbo Nozzles

Turbo Nozzles

Cleaning Nozzles featuring zero degree cleaning impact with a 25 degree pattern of coverage. High pressure commercial turbo nozzles are rated to 4500 and 210° F. Inlet ports are 1/4” FPT. Part No.

Nozzle #

Max. PSI

NP TC30 3.0 NP TC35 3.5 NP TC40 4.0 NP TC45 4.5 NP TC50 5.0 NP TC55 5.5 NP TC60 6.0 NP TC65 6.5 NP TC70 7.0

D

Net Ea.

4500 $ 52.05 4500 52.05 4500 52.05 4500 52.05 4500 52.05 4500 52.05 4500 52.05 4500 52.05 4500 52.85

General Rotating Nozzles Heavy Duty, Zero Degree Rotating Nozzles from General Pump. Ideal for water blasting, concrete cleaning, graffiti removal, etc. Zero degree impact but in a moving pattern for better coverage. All nozzles are rated to 194° F. Model Y3K nozzles are rated to 3000 psi at up to 8 gpm. Model Y5K nozzles are rated to 5000 psi at up to 10 gpm. Part No.

Nozzle #

Max. PSI

Y3K

Net Ea.

IP Y3K35 3.5 3000 $ 63.10 IP Y3K40 4.0 3000 63.10 IP Y3K45 4.5 3000 63.10 IP Y3K50 5.0 3000 63.10 IP Y3K55 5.5 3000 63.10 IP Y3K65 6.5 3000 63.10 IP Y5K35 3.5 5000 142.00 IP Y5K45 4.5 5000 142.00 IP Y5K55 5.5 5000 142.00 IP Y5K65 6.5 5000 142.00 IP Y5K90 9.0 5000 129.00 IP 100579 Filter/Strainer, 5000 PSI 8.92

D

Designed to provide a 200% cleaning efficiency increase over a 25 degree flat fan nozzle. The precision ceramic orifice and matching seat, along with the high strength forged brass housing, provide long-life with no gears, teeth or bearings to wear out. Inlet ports are 1/4" FPT. Maximum temperatures to 190 degrees F. Effective cleaning coverage is comparable to a 25° pattern but with 0˚ impact. Note: See turbo filters on other pages. Part No. Nozzle Max. PSI Net Ea. NP ST357-3 3.0 3600 $ 41.75 NP ST357-35 3.5 3600 41.75 NP ST357-4 4.0 3600 41.75 NP ST357-45 4.5 3600 41.75 NP ST357-5 5.0 3600 41.75 NP ST357-55 5.5 3600 41.75 NP ST357-6 6.0 3600 41.75 NP ST357-7 7.0 3600 41.75 NP ST357-8 8.0 3600 41.75 NP ST456-3 3.0 5000 53.95 NP ST456-4 4.0 5000 53.95 NP ST456-45 4.5 5000 53.95 NP ST456-5 5.0 5000 53.95 NP ST456-55 5.5 5000 53.95 NP ST456-6 6.0 5000 53.95 NP ST456-8 8.0 5000 53.95 NP ST457-3 3.0 6000 73.95 NP ST457-35 3.5 6000 73.95 NP ST457-4 4.0 6000 73.95 NP ST457-45 4.5 6000 73.95 NP ST457-5 5.0 6000 73.95 NP ST457-55 5.5 6000 73.95 NP ST457-6 6.0 6000 73.95 NP ST457-7 7.0 6000 73.95 NP ST457-8 8.0 6000 73.95 NP ST457-9 9.0 6000 73.95 NP ST457-10 10.0 6000 73.95 NP ST457-12 12.0 6000 133.00 NP ST457-15 15.0 6000 133.00 Repair Kits Available - Call Us for Details

Giant Turbo Nozzles give you 0° high pressure impact with a 25 degree angle spray coverage. Standard Features: Heavy duty brass housing with polymer cover • High impact ceramic nozzle and seat for durable, long life • Composite material rotor for high temperatures • 1/4" FPT inlet • 3600 PSI Nozzles are rated to 194° F. and 5100 PSI Nozzles are rated to 212° F.

D

Rotating “Tornado” Nozzles from Cat Pumps®. Unique spiral blasting action gives you 0° cleaning power with 25° coverage. Quickly covers a wide path with intense cleaning results. Durable ceramic nozzle offers greater resistance to wear. All nozzles have 1/4" FPT inlet and easily mount to any extension with a 1/4" male fitting.

22040 Series

D

Features: • Converts 0° blasting power to a 25° spinning action to agitate dirt loose • Quickly mounts to any lance with a 1/4” NPT Male fitting.

D

7270

Nozzle Size

This is how the Turbo Nozzle works.

Part No. Nozzle Max. PSI Net Ea. GU 22047 2.0 3600 $ 51.85 GU 22041 3.5 3600 51.85 GU 22044 4.0 3600 51.85 GU 22040 4.5 3600 51.85 GU 22045 5.0 3600 51.85 GU 22042 5.5 3600 51.85 GU 22046 6.0 3600 51.85 GU 22043 7.0 3600 51.85 GU 22048 8.0 3600 51.85 GU 22049 10.0 3600 51.85 GU 22040-12 12.0 3600 51.85 GU 22040-15 15.0 3600 51.85 GU 22040-20 20.0 3600 51.85 GU 22060-20 2.0 5100 98.50 GU 22069 3.0 5100 98.50 GU 22062 4.0 5100 98.50 GU 22060 4.5 5100 98.50 GU 22067 5.0 5100 98.50 GU 22061 5.5 5100 98.50 GU 22066 6.0 5100 98.50 GU 22065 6.5 5100 98.50 GU 22063 7.0 5100 98.50 GU 22068 8.0 5100 98.50 GU 22064 12.0 5100 98.50 GU 22060-150 15.0 5100 98.50 GU 22060-180 18.0 5100 98.50 GU 22060-200 20.0 5100 98.50 GU 22175 Turbo Filters/Strainers, 5100 psi 10.75

Similar in design to the standard Rotojet Nozzles but in a much more compact, smaller version. Overall length is only 2-1/2”. 25° pattern with zero degree impact. Rated to 3000 psi and 210° F. Inlet is 1/4” FPT.

Net Ea.

Part No.

Nozzle

Max. PSI

D

Net Ea.

This is how the Mini Rotojet Nozzle works.

MV 5620 3.0 3000 $ 26.95 MV 5630 3.5 3000 26.95 MV 5640 4.0 3000 26.95

Note: #22175 Filters will greatly extend nozzle life.

(800) 228-9666

ST456

Mini Rotojet Nozzles

CC 36402 3000 PSI 4.5 - 25° $ 67.10 CC 7265-55 3000 PSI 5.5 - 25° 68.10 CC 7265-65 3000 PSI 6.5 - 25° 68.10 CC 7270-45 5000 PSI 4.5 - 25° 202.00 CC 7270-55 5000 PSI 5.5 - 25° 202.00 CC 7270-65 5000 PSI 6.5 - 25° 202.00 CC 7270-90 5000 PSI 9.0 - 25° 202.00 GU 22175 Turbo Filters/Strainers, 5100 PSI 10.75

DULTMEIER SALES • OMAHA, NE

ST457

Note: #22175 Filters will greatly extend nozzle life.

• Durable ceramic nozzle offers greater resistance to wear • Maximum Temperature is 176° F.

Maximum Part No. Pressure

22060 Series

D

• Unique spinning action quickly covers a wide path with intense cleaning results D

ST357

Turbo/Laser Nozzles

Y5K

Tornado Nozzles

36402

D D

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0082


Rotating Spray Nozzles

137

Sudden Impact Rotating Nozzles

Rotomax Rotating Nozzles

4.15” Brass

Rotating Nozzles developed specifically for the rigors of the Car and Truck Wash Industries. Brass or stainless nozzles feature a plastic cover to protect vehicles and nozzles. Lasts up to 5 times longer than conventional turbo nozzles. Also, less water use.

D

Available in 24 degree pattern for maximum impact or in 30 degree pattern for extended coverage. Ideal impact distance is 20-30” from vehicle for 324 nozzles, 25-35” for 524 and 15-25” for 330 D models. Inlet ports are 1/4” FPT. s s e l Rated to 180° F. All nozzles are ain ” St 3.05 rebuildable.

D

Part No. Max. PSI Angle HY TUR324B-2 thru 6 Brass Nozzle 1750 24 HY TUR330B-2 thru 6 Brass Nozzle 1750 30 HY TUR324S-2 thru 6 S.S. Nozzle 3000 24 HY TUR330S-2 thru 6 S.S. Nozzle 3000 30 HY 3320-0053 * 1/4” MPT x 1/4” MPT Brass Check Valve HY 3320-0054 * 3/8” MPT x 1/4” MPT Brass Check Valve * 3.5 GPM & 1300 PSI.

Net Ea. $ 82.85 98.40 92.85 112.50 10.30 12.30

Blast-Tec Rotating Nozzles are designed specifically for the rigors of the carwash industry. Long life, rebuildable design provides zero degree impact with 24 degree coverage. Superior cleaning characteristics compared to other nozzles. Rated to 1000 PSI and 120° F. Stainless steel housing and tungsten carbide wear surface. Flow rates from 1.0 to 3.0 GPM. All nozzles have BSP inlet port. Adapters for 1/8” of 1/4” FPT are available. Length with adapter installed is approximately 3.20”.

All nozzles feature a built-in, 40 mesh, stainless filter to prevent clogging. Nozzles are rated to 3000 psi and 180° F. Inlet connection is 1/4" FPT. Complete Nozzles

Nozzle Adapter

Variable/Hi-Lo Nozzles Variable Pattern, Hi-Lo Nozzles for use with pressure washers and downstream soap injectors. Infinitely adjustable spray pattern from a solid stream to a wide flat fan. Push-pull design of nozzle also enables it to act as a Hi-Lo nozzle for use with “downstream” soap injection. Inlet port is 1/4" FPT. Rated to 3000 psi and 8 gpm. Maximum temperature is 176° F. (Spray Range is approximately 0° - 60° pattern.) Part No.

Orifice Size

Net Ea.

NP ST591-4 4.0 $ 15.90 NP ST591-45 4.5 15.90 NP ST591-5 5.0 15.90 NP ST591-55 5.5 15.90 NP ST591-6 6.0 15.90

D

This is how the Turbo Nozzle works.

PowerJet Oscillating Spray Nozzles from Spraying Systems. Delivers 50% more impact than conventional spray nozzles. Unique design oscillates a solid stream into a 15° flat spray pattern. No moving parts, no vibrating reaction. PowerJet nozzles cost less initially and are less expensive & easier to repair than other “rotary” D nozzles. Nozzle body and inlet cap D are brass, fluidic internal Side to Side cartridge is high performance Coverage plastic, outer cover is rubber. When wear does occur, simply replace the internal cartridge.

D

Nozzle Flow @ 1000 PSI Net Ea. #2 1.00 GPM $ 72.65 #3 1.50 GPM 72.65 #3.5 1.75 GPM 72.65 #4 2.00 GPM 72.65 #4.5 2.25 GPM 72.65 #5 2.50 GPM 72.65 #5.5 2.75 GPM 72.65 #6 3.00 GPM 72.65 1/8” FPT Adapter....................... 5.30 1/4” FPT Adapter....................... 5.30

Color Part No. Code Nozzle # Maximum PSI Net Ea. IP MAX1 Red 4.0 3500 $ 46.95 IP MAX2 Blue 5.0 3500 46.95 IP MAX3 Black 6.0 3500 46.95 IP MAX581 Red 3.5 5800 113.00 IP MAX583 Black 5.0 5800 113.00 IP 100579 Turbo Filters/Strainers, 5000 psi............ 8.92 IP 190040 Repair Kit for Rotomax Nozzles............. 20.15

Oscillating Spray Nozzles

Blast-Tec Rotating Nozzles

Part No. HF 1001106 HF 1001107 HF 1001108 HF 1001109 HF 1001110 HF 1001111 HF 1001112 HF 1001113 HF 3000581 HF 3000572

Rotomax Rotating Nozzles from General Pump. Designed to improve the cleaning efficiency of any pressure washer. Produces a rotating action of a 15 degree pattern while providing the impact of a zero degree nozzle. Inlet is 1/4" FPT. Maximum temperature is 176° F. Overall length is 4.1"

Part No. Orifice Number Color Band Net Ea. SS 38950-1404 4.0 Blue $ 70.35 SS 38950-1405 5.0 Green 70.35 SS 38950-1406 6.0 Yellow 70.35 SS 38950-1407 7.0 Red 70.35 SS 38950-1408 8.0 Orange 70.35 SS 38955-04 to 08 Replacement Cartridge.......... 35.95

Oscillating Turbo Spray Nozzles From Giant! Turbo Spray Nozzles with an oscillating pattern. The cleaning width of a fan nozzle with the hitting power of a 0 degree jet.The unique difference between these nozzles and normal Turbo Nozzles is that the oscillating nozzles move back and forth instead of in a circular pattern. This gives much better coverage ability.

Twin Turbo Lance

D

456L-3 D

Side to Side Coverage

42”

From Suttner! Dual Wand Extensions with Turbo Nozzles. Use with your existing trigger wands to double your cleaning coverage and shorten cleaning time. Extensions are constructed of 304SS stainless steel. Inlet is 1/4" MPT. Two #3 turbo nozzles are included. Model 357 is rated to 3000 psi and 190° F. Model 456 is rated to 5000 psi and 200° F. Other sizes available. Part No. NP 357L NP 456L-3

Max. PSI 3000 5000

Orifices (2) #3 (2) #3

Length 40" 42"

DULTMEIER SALES • OMAHA, NE

Net Ea. $ 129.00 173.00

(800) 228-9666

Maximum flows to 3.9 gpm and pressure to 3600 psi. Maximum temperatures to 212° F. Connection port is 1/4" FPT. Effective spray angle is 24°.

www.dultmeier.com

Part No. Nozzle # Max. PSI Net Ea. GU 22700-00 3.0 3600 $ 77.10 GU 22700-35 3.5 3600 77.10 GU 22700-40 4.0 3600 77.10 GU 22700-45 4.5 3600 77.10 GU 22700-50 5.0 3600 77.10 GU 22700-55 5.5 3600 77.10 GU 22175 Turbo Filters/Strainers, 5100 psi 10.75 Note: #22175 Filters will greatly extend nozzle life.

• DAVENPORT, IA

(800) 553-6975

E0666


Spray Nozzles • Sandblast Kits • Wiper Bags

138

X-Jet Cleaning Nozzles High Pressure, High Throw Nozzles that are ideal for a wide variety of cleaning and spraying applications. Unique design eliminates the need for ladders, scaffolding or telescoping wands. Designed to project or throw chemicals as high as 40’. Injects and proportions chemicals or liquids without going through your pump, hose or wand. Now you can easily apply caustic cleaners without damaging your equipment. Great for use in removing mold, dirt and mildew from homes and buildings or other tall structures. The X-Jet Nozzles are also ideal for tree and orchard spraying. All nozzles are sold in nozzle kits and include X-Jet Nozzle, 1/4” quick coupler, metering tips, 15’ of inlet chemical hose, shutoff valve and inlet strainer. (Replacement nozzles or inserts are also available). Overall length is only 4” long with quick coupler installed. Can be use on virtually any pressure washer from 1,000 to 6,000 psi. Available in Two Different Styles: Original X-Jet Nozzles feature a fixed spray pattern and come with a range of chemical inserts when needed. M5 X-Jet Nozzles feature an adjustable pattern design with a 0-60 degree fan spray. Inserts also included.

D

The X-Jet in Action

D

M5 Version

X9 Version

D

Close Range Nozzle Included

X9 Full Kit

D

M5-16 Full Kit

Part-No. Type Flow Range XJ X9 Original, Fixed 3-4 GPM @ 2000-3000 PSI XJ X13 Original, Fixed 4-7 GPM @ 3000-4000 PSI XJ X16 Original, Fixed 8 GPM @ 4000-5000 PSI XJ M5-9 Adjustable Pattern 3-4 GPM @ 2000-3000 PSI XJ M5-13 Adjustable Pattern 4-7 GPM @ 3000-4000 PSI XJ M5-16 Adjustable Pattern 8 GPM @ 4000-5000 PSI Note: Other Sizes are Available on Request.

Net Ea. $ 112.00 112.00 112.00 127.00 127.00 127.00

D D

WIPER COVER BAGS

Water Sandblasting Kits

Great for Protecting Rear Wiper Blades During the Wash Process!

D

• WWB50 Bags are 3” Wide x 27” Long, 1.5 Mil • WWB75 Bags are 5” Wide x 27” Long, 1.5 Mil • Sold in Rolls of 500 Bags

KITS INCLUDE: Mixing nozzle, sand inlet barb, sand probe and spray nozzle. Note: 1/2" sand hose is not included . (Should not exceed 25')

Shown on Vehicle

5% Discount on 12 or More Rolls & 10% on 24 or More

Kits will operate in the range of 1000 to 3000 PSI and up to 190* F. These kits feature tungsten lined nozzles. D

Part No.

DU WWB50 DU WWB75

WATER SANDBLAST KITS: These kits are used in conjunction with high pressure wash units for jobs where extra-heavy cleaning is required. Works well for removing rust, metal scale, paint, etc. Lightweight, compact design for ease in handling. Stainless steel spray nozzle for long life is matched to the GPM output on your washer.

Part-No. Flow/GPM Make Net Ea. IP ZMS0 Water Blaster Kit 2.7 - 3.7 General $ 102.50 IP ZMS1 Water Blaster Kit 3.2 - 5.6 General 102.50 IP ZMS3 Water Blaster Kit 4.2 - 7.3 General 102.50 IP ZMS4 Water Blaster Kit 5.5 - 9.5 General 103.00 TF WF050 1/2" Sand Tubing, per foot........................................... 1.27

Net Ea.

Wiper Bags, 3” Wide, Roll of 500 Wiper Bags, 5” Wide, Roll of 500

DULTMEIER SALES • OMAHA, NE

$ 19.95 24.95

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0748


139

Gutter Cleaning System • Tank Nozzles Gutter Cleaning System

The Gutter Cleaning System is a great item for increasing revenues. Unique, patent-pending Gutter Ball is designed for cleaning debris from residential or commercial gutters.

FPT Inlet

Rotary Tank Washing Nozzles 1/2” or 3/4”

A new dimension of performance and versatility in low pressure cleaning/rinsing applications. Cleans diameters to 10’. Two-piece nozzle features a spray head that is rotated by the pressurized flow of the spray solution. Can be operated at pres­sures of 10 PSI to 50 PSI. The multiple orifice configuration of the spray head provides exceptional coverage. 360° coverage. 1/2” is rated to 12 GPM @ 50 PSI. 3/4” is rated to 20 GPM @ 50 PSI.

Designed for the Pressure Wash Professional, the stainless ball correctly directs flow at the precise angle to clean hard-to-reach gutters from the ground. Can be used with almost any pressure washer with telescoping wand extensions. Flow rates are shown to match different pressure washers and applications.

Part No.

Assemblies Include: Stainless steel gutter ball • Stainless steel coupler • 45 Degree high pressure elbow • (2) Male couplings • (2) Stainless steel nozzles • Inlet is 1/4” male quick coupling.

D

Net Ea.

SS 55270-1/2-11 1/2" Rotary Nozzle................... $ 45.20 SS 55270-3/4-18 3/4” Rotary Nozzle................... 45.20

D

Ball Type Rinsing Nozzles

Note: See the Dultmeier Sales Web Site at dultmeier.com for a link to the manufacturer’s how-to-operate video.

Ball Type Rinsing Nozzles are designed to rinse the inside of chemical containers. Nozzles are standard with 40 orifices that have a total spray angle of 240°. Construction is Nylon. Ports are 1/2" FPT or 3/4" FPT. Fixed spray pattern, no rotation. Flow Rate Part No. Ports @ 100 PSI Net Ea.

D

SS VSM-28 SS VSM-44 SS VSM-90 SS VSM-140 SS VSM-190

1/2” or 3/4” Inlet

1/2" FPT 8.7 GPM $ 22.15 1/2" FPT 13.7 GPM 22.15 3/4" FPT 28 GPM 213.00 3/4" FPT 43 GPM 213.00 3/4" FPT 59 GPM 213.00 1” MPT Inlet

Rotary Tank Nozzle Self-operated by the cleaning water. A fast and effective method of cleaning the interior of any sprayer tank. Jets rotate about a horizontal axis. Cover up to a 20' Diameter area. Material is Nylon. Operating pressure from 50 to 275 PSI. Inlet connection is 1" MPT.

Flow Rate Part No. @ 3000 PSI Net Ea.

GB GB02 Gutter Ball Assembly GB GB25 Gutter Ball Assembly GB GB03 Gutter Ball Assembly

3.4 GPM 4.4 GPM 5.2 GPM

$ 84.95 84.95 84.95

28

Net Ea.

DU 1LTC

$ 47.70

Rotating Rinsing Nozzles

FPT Inlet

Gutter Cleaning Wands Gutter Cleaning Wands are rated to 4100 PSI. Chrome-plated construction. Both models feature 1/4” male quick coupler inlet and 1/4” female quick coupler outlet. Model 2201 is the smaller unit and is 6” long to the bend. Model 2203 is 28” long to the bend.

Part No.

D

D

For Tank Cleaning Applications. This rinse nozzle has three orifices which create rotational forces to provide spherical coverage. 303 stainless with hardened SS bearings and races. Internal Teflon sleeve. 1/2" FPT connection. Requires 1-1/32" tank opening. Maximum pressure is 200 PSI.

2203

6”

Nozzle No.

2201

Capacity Gallons Per Minute 20 psi

30 psi 40 psi

50 psi 60 psi

23240-3-HSS-5.7-SS 4.0 4.9 5.7 6.4 7.0 23240-3-HSS-7-SS 4.9 6.1 7.0 7.8 8.6

Part No.

Length

Max. PSI

Part No. Net Ea. SS 232403HSS57SS $ 322.50 SS 232403HSS7SS 337.50

Net Ea.

MV 2201 6” 4100 $ 6.25 MV 2203 28” 4100 15.75

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0893


Rotary Cleaners • Tank Nozzles Rotary Tank Nozzle

140

Rotary Cleaners 3rd Nozzle Port

Self-Rotating Tank Cleaning Nozzle. Designed for cleaning interior surfaces of tanks, drums, barrels, pipe or tubing. (4) Spinning nozzles travel in an orbital axis for complete coverage. Stainless steel construction, built in strainer, teflon seals and EPDM o-rings are standard. Rated from 6-32 GPM and from 400 to 2000 PSI. Models are available for fixed rigid pipe mounting or non-rigid hose mounting. Rotation speed is 10 - 16 RPM. Temperatures to 195° F. Inlet is 3/4”. Length is 10-1/2”. Minimum tank opening is 7-1/2”. (Note: Must specify flow rate, pressure, diameter to be cleaned and if any chemicals will be used). Part No.

Mount

Wt.

IP A80R

Rigid

11 lbs.

D D

81556 or 81756

3/8" FPT

An ideal accessory for use with hot or cold water pressure washers. Can be used to clean tanks, ducts, vents, portable toilets, pipe runs and many more. Easily mounted to rigid lance or high pressure hose. Corrosion-resistant, stainless and plated brass construction with self-lubricated bearings and carbide swivels.

Net Ea.

$ 3023.00

Tank Cleaning Nozzles Designed for cleaning of tanks, barrels and drums. Nozzles spin as main body rotates giving complete orbital coverage to interior surfaces. Rotating bodies are driven by electric or pneumatic motors or are self-propelled and driven by the water flow. Stainless steel construction with built-in filters. (2) or (4) nozzles are included but must be matched to your flow and pressure requirements. Rate to 195° F. (Note: Flow and pressure required for correct sizing as well as tank diameter and any chemicals that may be used).

81506

M21 Nozzle is rated to 5.5 GPM at up to 3200 PSI. Minimum tank opening is 2-1/2”. Electric 110 volt motor is the only drive available for this model. Length is 39”. Weight is 7 lbs. M63 Nozzles are rated from 6 to 10 GPM and 450 to 2000 PSI. Minimum tank opening is 3-1/4”. Self-propelled, 24 volt electric or pneumatic drives are available. Inlet is 3/4” on self-propelled and 3/8” on electric and air models. Length is 48-1/2”. Weight is 14 lbs. M85 Nozzles are rated from 6 to 21 GPM and 450 to 2000 PSI. Minimum tank opening is 6”. Self-propelled, 24 volt or pneumatic drives are available. Inlet is 3/4” on self-propelled and 3/8” on electric and air models. Length is 51”. Weight is 14 lbs.

M63E M85E

M63P M85P

Adjustable 2 or 3 nozzle design is perfect for 360 degree cleaning. (1/8” nozzles are not included and must be matched to your system). Rated to 4000 PSI and 250° F. Inlet is 3/8” FPT. (1/4” also available).

Nozzle Type

81526

Part No.

Diameter

MM 81506 MM 81526 MM 81556 MM 81566 MM 81706 MM 81726 MM 81756 MM 81766 MM 81925

3" 2 1.1 lbs. 6" 2 2.2 lbs. 12" 2 2.8 lbs. 16” 2 3.3 lbs. 3” 3 1.1 lbs. 6” 3 2.2 lbs. 12” 3 2.8 lbs. 16” 3 3.3 lbs. Rotary Nozzle Wand Assembly.......

Wt.

CALL for PRICING

3/8” FPT Inlet D

Manhole Cleaners

M63 M85 1/8” Nozzle Ports

Unique Rotary Cleaners are designed to fit 16” or 24” manhole openings. Two-arm cleaners feature debris shield and safety cage. All stainless steel construction. Rated to 5000 PSI. Inlet swivel is 3/8” FPT. Designed for 1/8” MPT, (zero or 5 degree) spray nozzles which are not included and should be matched to your pump system.

M21

Part No.

Drive

Capacity

IP M21 110V Electric 1.0 - 5.5 GPM IP M63E 24V Electric 6 - 10.5 GPM IP M63P Pneumatic 6 - 10.5 GPM IP M63 Self-Propelled 6 - 10.5 GPM IP M85E 24V Electric 6 - 21 GPM IP M85P Pneumatic 6 - 21 GPM IP M85 Self-Propelled 6 - 21 GPM DULTMEIER SALES • OMAHA, NE

Net Ea.

$ 1010.00 1689.00 3198.00 2998.00 2143.00 3281.00 3325.00

(800) 228-9666

Part No.

Size

Max. Flow

Wt.

MM 81916 MM 81917 MM 81923

16” 24” 26”

10-12 GPM 10-12 GPM 50-60 GPM

5 lbs. 7 lbs. 8 lbs.

www.dultmeier.com

• DAVENPORT, IA

CALL for PRICING

(800) 553-6975

E0944


Ball Nozzles & Joints

141

Adjustable Ball Nozzle Assemblies Chemically Resistant, Adjustable Ball Nozzle Assemblies for rinse, soap or wax arches, de-icing spraybars or industrial applications. Designed for adjustable direction of nozzles for the most effective coverage. Bodies are available with 1/4", 3/8" or 1/2" MPT threads or with a clip-type clamp for 1" through 2" pipe. Nozzles are available in two styles: Ball/Nozzle combinations (CA & CT numbers) or ball joints only with a threaded ports for use with existing 1/4" or 3/8" MPT nozzles.

#20570 Clamp Assembly

No. 37235 Threaded Type Body with Cap

D

For complete assemblies, order the body of choice (cap included) and the nozzle type and size required or the ball only if using your own tips. Threaded bodies are rated to 125 psi. Clip-eyelet bodies are rated to 60 psi. Both will handle temperatures to 180° F. Plastic parts are polypropylene for excellent chemical resistance.

Body CP20582

CA Ball Nozzle Flat

(CA) Hollow cone spray pattern - Interchangeable tips

Hollow

Hollow Nozzle

(CT) Flat Fan spray pattern - Interchangeable tips

Part No. Net Ea. SS 37235-1/4PP * 1/4" MPT Body with cap.................... $ 5.95 SS 37235-3/8PP 3/8" MPT Body with cap...................... 5.95 SS 37235-1/2PP 1/2" MPT Body with cap...................... 5.95 SS 20570D-1 Clip Body with cap for 1" pipe.............. 3.31 SS 20570D-1-1/4 Clip Body with cap for 1-1/4" pipe........ 3.31 SS 20570D-1-1/2 Clip Body with cap for 1-1/2" pipe........ 3.31 SS 20570D-2 Clip Body with cap for 2" pipe.............. 5.10 SS CA XXXX † CA Series Hollow Cone Nozzles...... 3.56 SS CT XXXX † CT Series Flat Fan Nozzles.............. 2.72 SS CP20582-1/4PP Ball ONLY, 1/4" FPT, for existing tips.... 1.89 SS CP20582-3/8PP Ball ONLY, 3/8" FPT, for existing tips.... 1.89 * 1/4" body not recommended for capacities over 3 GPM. † Specify Full Number from chart.

Adjustable Ball Joints Brass or Stainless Adjustable Ball Joints for Soap and Rinse Arches. Designed for 1/4", 3/8" or 1/2" male thread nozzles. Allows for a wide adjustment range for complete coverage. Standard with male MPT inlet and female FPT outlet. Rated to 300 PSI.

dultmeier.com

Nozzle Not Included Female Nozzle Fitting Male Inlet Fitting

D

D

Typical Application

Part No.

SS 36275-1/4X1/4 SS 36275-1/4SS SS 36275-3/8X3/8 SS 36275-3/8SS SS 36275-1/2X1/2 SS 36275-1/2SS

Pipe Size (M X F)

Net Ea.

1/4" Brass 1/4" Stainless 3/8" Brass 3/8" Stainless 1/2" Brass 1/2" Stainless

$ 8.95 29.85 46.05 94.15 65.40 125.50

• Shop and Order On-Line 24 Hours a Day, 7 Days a Week! • Large Inventories of Over 3 Million Total Items!

SERVICE & REPAIRS

• View Current Pricing! • Web Specials and Bargain Corner!

Did you know? We can service almost every brand of pump we sell in our catalog.

• Know Your Part Numbers? Use the Web Quick Order Page! • Hundreds of Parts List Schematics (and more to come!) • Technical Library packed with information! • See New Items not Shown in Our Printed Catalogs!

Call us at 1-800-228-9666 (Omaha, NE) for a quote! DULTMEIER SALES • OMAHA, NE

• Track Your Order Status and History! • Secure Site for Safe On-Line Ordering.

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E1011


Nozzle Accessories Diaphragm Check Valves

Diaphragm Check Valves – Side Style –

Made of Nylon with Celcon bonnet. Check valve opens at 7 PSI pressure.Male inlet connection and female outlet connection.Choice of 1/2" & 3/4" NPT sizes. Large capacity flow rates: up to 10 GPM for 1/2" NPT size; up to 15 GPM for 3/4" NPT size. Overall length 3". Weight is 9 oz. Maximum Temperature is 125° F.

• Standard Check Pressure is 10 PSI. (2, 5, 8, 15 & 20 PSI also available) • 300 PSI Maximum Pressure • Maximum Temperature is 125° F.

D

Type 12328NY-1/2 1/2" NPT male and female No. Net Ea. inlet outlet

SS 12328NY-1/2 SS 12328NY-3/4 SS 12338-1/2NY SS 12338-3/4NY SS 12335VI

1/2" Check Valve ................... $ 52.60 3/4" Check Valve ................... 52.60 Replacement Body for 1/2".... 16.75 Replacement Body for 3/4".... 16.75 Replacement Viton® Diaphragm 7.34

– Side Style & Top Style –

Part No. SS QJ8360NYB Diaphragm Check Valve with 1/4" MPT Inlet. SS QJT8360NYB Diaphragm Check Valve with 11/16"-16 Inlet SS 21953VI Diaphragm (Viton®) for Check Valve............ SS CP21953-EPR Diaphragm (EPDM) for Check Valve.............. SS 19191EPR Gasket for QJT as extra.................................. SS 58140 Manual Nozzle Shut-Off................................. Note: 21950-2,5,8,15,20NYB End Caps Available.

Both the QJ cap and check body incorporate John Guest end connections for use with 1/4” or 3/8” tube. This is a modified QJ8360NYB. EPDM o-ring in the John Guest insert. Mounting slots will accept 10-24 screws or can be cable tied. Overall length of the cap/ body assembly is 3-1/2”.

D

• Viton® or EPDM Diaphragms • 300 PSI Maximum Pressure

QJ22187

• Requires 3/8" Hole in Pipe

CP25609 Cap

• Caps, Nozzles, Gaskets Not Included (See other pages).

QJ Cap

QJ Body

D

John Guest 90° Push to Connect Adapter Cap

Diaphragm Nozzles

Drip-Free Diaphragm Check Valves

D

Net Ea. $ 3.51 3.35 .95 .32 1.01 3.28

Part No. Net Ea. SS QJ98588-NYR John Guest QJ Cap for 1/4” ................................. $ 3.20 SS QJ98586-NYR John Guest QJ Cap for 3/8” ................................. 3.20 SS QJ98598-90-14 John Guest 90° Cap for 1/4”................................. 4.02 SS QJ98599-90-38 John Guest 90° Cap for 3/8”................................. 4.02 SS QJ98592-1/4-2 John Guest Body for 1/4” Tube with 2# Check..... 6.66 SS QJ98592-1/410 John Guest Body for 1/4” Tube with 10# Check... 6.66 SS QJ98590-3/8-2 John Guest Body for 3/8” Tube with 2# Check..... 6.66 SS QJ98590-3/810 John Guest Body for 3/8” Tube with 10# Check... 6.66 SS 18999EPR EPDM Gasket as Replacement........................... .62 Caps Include EPDM Gasket.

Part No. Net Ea. SS QJ17560-1/2 ** Split-Eyelet Check Valve for 1/2" Pipe....... $ 2.91 SS QJ17560-3/4 ** Split-Eyelet Check Valve for 3/4” Pipe....... 3.03 SS QJ17560-1 ** Split-Eyelet Check Valve for 1" Pipe.......... 3.03 SS QJ22187-3/4 * Split-Eyelet Check Valve for 3/4" Pipe ....... 6.45 SS QJ22187-1 * Split-Eyelet Check Valve for 1" Pipe........... 6.45 SS 21953VI Diaphragm (Viton®)......................................... .95 SS CP21953-EPR Diaphragm (EPDM)......................................... .32 SS 21950-2NYB Diaphragm End Cap Assembly - 2 PSI .......... 2.35 SS 21950-5NYB Diaphragm End Cap Assembly - 5 PSI........... 2.35 SS 21950-8NYB Diaphragm End Cap Assembly - 8 PSI........... 2.35 SS 21950-10NYB Diaphragm End Cap Assembly - 10 PSI......... 2.35 SS CP25611 QuickJet Cap for 01-08 Orifices, Less Gasket .47 SS CP25609 QuickJet Cap for 10-20 Orifices, Less Gasket .42 * EPDM Diaphragm. ** Viton® Diaphragm.

1/4" MPT Inlet

QJ8360NYB Diaphragm Check Valve

D

John Guest Check Valves by TeeJet

• Standard Check Pressure is 10 PSI. 2, 5 & 8 PSI are also available

QJ17560

D

QJT8360NYB Check Valve Adapter 11/16/16F x QuickJet

Split Eyelets D

Shown with QuickJet Cap & Nozzle-Has 1/4" MPT

• Viton® Diaphragm

FLOW RATE, G.P.M. 5 7 10 15 20 25 Pressure Drop, p.s.i. 1.0 1.8 3.6 8.2 14.4 23 For 12328-NY-1/2 Pressure Drop, p.s.i. 0.5 0.9 1.9 4.3 7.7 12 For 12328-NY-3/4

Part

142

• 1/4" NPT male inlet connection.

The ideal choice for chemical or soap arches. Nozzle bodies feature 3 PSI, 8 PSI or 25 PSI check valve springs for drip-free operation. Both models are standard with 1/4" MPT inlet and 1/4" FPT outlet. Designed for 1/4" spray nozzles to screw right in. Bodies are nylon and are rated to 300 psi. Seals are EPDM for added chemical resistance.

Model 402CPV03 has a 3 PSI cracking pressure. Model 402CPV01 has a 8 PSI cracking pressure. Model 402CPV02 has a 25 PSI cracking pressure.

1/4" FPT Outlet

D

D

• Nylon with stainless steel diaphragm spring 8360NYB with new style Cap No. 21950PPB

13431NY Long Shank Nozzle Body shown with old style Cap No. 8476NY

8360NYB & 13431NY Nylon Diaphragm Nozzle Bodies are supplied less the Tip, Cap & Strainers. For rates up to 1-1/2 GPM - originally designed for dependable performance during aerial spraying operations. The springbacked diaphragm valve provides instant positive closure when pressure is shut off. The 13431NY Nozzle has a longer threaded shank for use with Vari-Spacing type clamps. 10 PSI check valve is standard (2, 5, 8, 15 & 20 PSI also available). Maximum temperature is 125° F. Part No. Net Ea. SS 8360NYB Check Valve with Viton® Diaphragm.... $ 9.92 SS 13431NY Long Shank Diaphragm Nozzle........... 9.65 SS 4676NY-1/4 Nylon Adaptor Caps ............................ 1.49 SS 4620VI Flat Viton® Diaphragm Before 1988..... .97 SS 21953VI Raised Viton® Diaphragm After 1988.. .95 SS CP21953-EPR EPDM Diaphragm................................ .32 Note: 21950-2,5,8,15,20NYB End Caps Available.

Part No. Description Net Ea. TW 402CPV03 * Drip-Free Diaphragm Check Valve: 3 PSI.... $ 3.57 TW 402CPV01 * Drip-Free Diaphragm Check Valve: 8 PSI... 3.57 TW 402CPV02 * Drip-Free Diaphragm Check Valve: 25 PSI. 3.57 TW 5860-36 EPDM Diaphragm.................................. .46 TW 5865-36 Viton® Diaphragm................................. 1.44 TW 4020-3 Housing & Spring, 3 PSI, Red............... 2.15 TW 4020-5 Housing & Spring, 25 PSI, Black........... 2.15 TW 5860-130 Housing & Spring, 8 PSI, Red............... 2.21 TW 2000-30 Retainer Cap Only................................. 1.13 * 5% Discount on 50+

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0088


143

Spray & FoamJet Nozzles & Accessories FoamJet Nozzles

These nozzles are designed to produce a low pressure aerated foam when used with detergent solutions. Available in plastic, brass and stainless steel. Great for soap or presoak arches. Air induction process pulls air into the chemical flow to create foam. Nozzles are available individually or in an assembly with diaphragm check valve and cap. Available in 20°, 40°, 65° and 80° patterns.

Split-Eyelet Assemblies The easiest and fasted way to mount spray nozzles to a boom. To install nozzles, drill hole, insert Split-Eyelet inlet and clamp assembly in place. Elevated inlet keeps sediment out of nozzle. Leakproof gasket connection. 11/16" -16 threads is designed for caps and flat head nozzles.

D

D

FJP

Part No.

1/4MEF Stainless

FJP Nozzles are Celcon plastic Nozzles with 1/4” MPT construction. Flat back design has no threads and must be held in place with nozzle bodies and caps shown on this page. Rated D to 150 psi. MEF Nozzles are stainless steel construction. Inlet is 1/4” MPT. Rated to 3000 psi. NOTE: In order to make the FJP D FJP or FJ Nozzles into a check valve/ Plastic nozzle assembly, order FJ or FJP Nozzles nozzle of choice, 8360NYB check valve and 18032ANY wing cap. Water Foam Spray Spray Part No. Body Orifice Angle Angle Net Ea. SS FJP2002CE Plastic 02 20 40 $ 15.95 SS FJP2003CE Plastic 03 20 40 15.95 SS FJP2004CE Plastic 04 20 40 15.95 SS FJP2005CE Plastic 05 20 40 15.95 SS FJP2006CE Plastic 06 20 40 15.95 SS FJP2010CE Plastic 10 20 40 15.95 SS FJP4002CE Plastic 02 40 75 15.95 SS FJP4003CE Plastic 03 40 75 15.95 SS FJP4004CE Plastic 04 40 75 15.95 SS FJP4005CE Plastic 05 40 75 15.95 SS FJP4006CE Plastic 06 40 75 15.95 SS FJP4008CE Plastic 08 40 75 15.95 SS FJP4010CE Plastic 10 40 75 15.95 SS FJP6503CE Plastic 03 65 85 15.95 SS FJP6505CE Plastic 05 65 85 15.95 SS FJP6508CE Plastic 08 65 85 15.95 SS FJP8002CE Plastic 02 80 105 15.95 SS FJP8003CE Plastic 03 80 105 15.95 SS FJP8004CE Plastic 04 80 105 15.95 SS FJP8006CE Plastic 06 80 105 15.95 SS FJP8008CE Plastic 08 80 105 15.95 SS FJP8010CE Plastic 10 80 105 15.95 SS 1/4MEF4005 SS 05 40 75 42.00 SS 1/4MEF4006 SS 06 40 75 42.00 SS 1/4MEF4007 SS 07 40 75 42.00 SS 1/4MEF4008 SS 08 40 75 42.00 SS 1/4MEF4010 SS 10 40 75 42.00 SS 18032ANY Wing Cap.......................................... .70 SS 8360NYB Diaphragm Check Valve, 1/4” MPT... 9.92

D

Nozzle Caps TeeJet Nozzle Caps fit all bodies having 11/16"-16 Male thread.

FJP shown with 1321 Body & 18032ANY Wing Cap

7421 Stainless

1325 Std. Cap Winged Cap

Std. Std.Pkg. Part No. Material Style Pkg. DISCOUNT Net Ea. SS CP8027NYB Nylon - 100 10% $ .49 SS 18032ANY Nylon Winged 100 10% .70 SS 1325B Brass Hex 100 10% .78 SS 1325SS Stainless Hex 100 10% 4.60 TW 8027NY Nylon - 100 10% .37 SS CP20230 * Brass - 100 10% .92 * Use with Ceramic Discs & Cores

Poly Strainers with Stainless Screens Part No. Screen *Std. Pkg. Discount Net Ea. SS 8079-PP24 24-Mesh 100 10% $ .67 SS 8079-PP50 50-Mesh 100 10% .67 SS 8079-PP100 100-Mesh 100 10% .67 SS 8079-PP200 200-Mesh 100 10% .67 * 10% Discount for Standard Package.

D

Flat Fan Spray Nozzles Flat Back Spray Nozzles for rinse or soap arches, wash down, dust suppression, etc. These nozzles are designed to be used with the bodies, caps and strainers shown on this page. Stainless steel construction. Rated to 500 PSI. Available from 25 to 65 degree patterns and a variety of flow orifices.

Stainless

4514 SLOTTED NYLON Strainers one-piece construction for use with liquids containing suspended solids. Maximum temperature is 160° F. 5053 BRASS Strainers with Stainless Screens A three part assembly consisting of body, cap & screw. 4193 POLY CHECK VALVE Strainers with Stainless Screens Polypropylene strainer & check valve prevents nozzle dripping. Fits all TeeJet nozzles. Ball check opens at 5 psi. For flow rates to 0.8 GPM. Also available in brass or stainless. Maximum temperature is 140° F. 9106 FUSED BRONZE FILTER Brass with fused bronze filter element equivalent to 300 mesh screen. For use with extra low capacity tips. Part No. Body Material Mesh Screen Pkg. Net Ea. SS 5053-50 Brass 50 Stainless 100 $ 1.57 SS 5053-100 Brass 100 Stainless 100 1.57 SS 4193A-PP24 Poly Check 24 Stainless 100 2.23 SS 4193A-PP50 Poly Check 50 Stainless 100 2.23 SS 4193A-PP100 Poly Check 100 Stainless 100 2.23 SS 4514-10NY Nylon - RED 50 Slotted Nylon 100 .70 SS 4514-20NY Nylon - YELLOW 25 Slotted Nylon 100 .70 SS 9106 Brass 300 Fused Bronze 100 1.71

(800) 228-9666

7421 Nylon

Fits Clamp OUTLET Pipe & Bolts Material Threaded Net Ea.

SS 7421-1/2TNY 1/2" Plated Nylon 11/16"-16 $ 2.52 SS 7421-3/4TNY 3/4" Plated Nylon 11/16"-16 2.52 SS 7421-1TNY 1" Plated Nylon 11/16"-16 2.52 SS 7421-1/2TSS 1/2" Plated Stainless 11/16"-16 8.25 SS 7421-3/4TSS 3/4" Plated Stainless 11/16"-16 8.24 SS 7421SS-1TSS 1" Stainless Stainless 11/16"-16 13.75 SS 8370B114-14 1-1/4" Stainless Stainless 1/4" FPT 23.15 SS 8370B114-38 1-1/4" Stainless Stainless 3/8" FPT 23.20 SS 8370B114-12 1-1/4" Stainless Stainless 1/2" FPT 23.15 SS 7418BU Rubber Gasket for 7421............................ 1.77

with 8360NYB

STRAINERS & CHECK STRAINER

DULTMEIER SALES • OMAHA, NE

D

Part No. Construction Orifice Pattern SS SS1504 Stainless 4 15° SS SS1506 Stainless 6 15° SS SS1508 Stainless 8 15° SS SS2504 Stainless 4 25° SS SS2506 Stainless 6 25° SS SS2508 Stainless 8 25° SS SS4004 Stainless 4 40° SS SS4006 Stainless 6 40° SS SS4008 Stainless 8 40°

— Other Nozzles Sizes Available —

Bodies

Net Ea $ 6.98 6.98 6.98 6.98 6.98 6.98 6.97 6.97 6.97

www.dultmeier.com

Strainer

• DAVENPORT, IA

Nozzle

(800) 553-6975

Cap

E0087


Nozzle Caps & Accessories “QUICKJET”

1/4” MPT Inlet

COLOR-CODED “Quick TeeJet” CAPS

NOZZLE ASSEMBLY SYSTEM Ideal for Tunnel Washes ! ! D

Complete Assembly

QJ8360NYB Diaphragm Check Valve. “Drip-Free” Shown with QuickJet Cap & Nozzle-has 1/4" MPT Inlet. Cracking pressure is 10 psi. Note: Cap, Gasket & Nozzle must be ordered separately.

For instant nozzle tip identification

When your operation calls for different size spray tips or when strainers need cleaning, time is important. The longer you shut down, the more it costs you! THE NEW “QUICKJET” WAY PROVIDES: A Quick “off-on” of caps and tip assembly

QuickJet Caps are available in 9 colors, and 9 different styles enabling you to develop your own color coding system. You can pre-assemble the Tips, Caps and Seat Gaskets in the convenience of your workshop or office. The caps are designed with grooves that fit locating lugs on the nozzle body. Caps are made of Celcon and are available for use with all spray tips D used in TeeJet nozzles. FOR PRESSURES UP TO 300 PSI The Quick TeeJet Caps are designed with grooves that fit locating lugs on the nozzle body. Caps are made of Nylon and are available for use with all TeeJet Spray Tips.

B Automatic self alignment of flat spray patterns C Color coding of caps D Can be used with all interchangeable TeeJet tips 1/4” FPT Outlet

Quick TeeJet Cap

CP25611

19438VI (Viton)

TeeJet Flat Spray Tips (Smaller Capacities) XR -01 Thru -08

DG

CP25609

TeeJet Flat Spray Tips (Larger Capacities) Standard -10 Thru -20

Permits use of standard 1/4" MPT nozzles.

CP25599

CP25607

SEAT GASKET “QUICKJET” CAP

for instant nozzle tip identification

CP25597 TEEJET SPRAY TIP

D

TK-VS Flood Jet

VisiFlo Spray Tip

VisiFlo Spray Tip

TK FloodJet

FL FullJet

TJ TwinJet

TX ConeJet

Al TeeJet

No. TJ60 Spray Tip

TG Full Cone

SJ StreamJet

No. AI Spray Tip

**Also use with DG TwinJet, Turbo TeeJet Induction (TTI) and Air Induction Turbo TwinJet (AITTJ60)

CP25607

QuickJet Caps are available in eight colors.You can easily preassemble the Tips, Caps, Check Valves and Seat Gaskets.The caps are designed with grooves that fit locating lugs on the nozzle body. QJ8360 Check valves are “drip-free” for chemical savings. See Cap Options in Other Column at Right. Part No. Net Ea. SS QJ8360NYB Diaphragm Check Valve 1/4" MPT....................... $ 3.51 SS QJ-1/4TTNYB Cap Adapter with 1/4" MPT Inlet .......................... 1.55 SS QJ-1/4TNYB Cap Adapter with 1/4” FPT Inlet............................ 1.53 SS QJ4676-1/4CEL Quick TeeJet Adapter, 1/4" FPT with gasket ....... 1.26 SS 21953VI Viton® Diaphragm for check valve as replacement .95

18999EPR (EPDM Standard)

QJ4676-1/4CEL

1/4" FPT Adapter Has 1/4" FPT thread for drop pipe, pressure gauge, etc. Available in Black only with EPDM Gasket

QJ19843CELR

Blank Cap with Gasket To Temporarily shut-off selected Nozzles Available in Black only with EPDM Gasket

QJ4676-45-1/4 45° Quick TeeJet Cap with 1/4" FPT With EPDM Gasket

QJ4676-90-1/4 90° Quick TeeJet Cap with 1/4" FPT With EPDM Gasket

QuickJet Caps Less Gasket - Specify Color Number

Nozzle Bodies

1 2 3 4 5 6 7 8 9* Part No. Black White Red Blue Green Yellow Brown Orange PP Gray Net Ea. SS CP25597 x x x x x x x x $ .48 SS CP25599 x x x x x x x .48 SS CP25607 x x x x x x x x * x .48 SS CP25609 x x x x x x x .47 SS CP25611 x x x x x x x x * x .42 x = Cap is available in that color. *Polypropylene Caps (PP) are an additional 15%.

D

TeeJet Nozzle Bodies have 11/16"-16 Male thread for TeeJet Caps and adapt to the various pipe thread sizes listed below. Std. *Std.Pkg. Part No. Material Pipe Thread Pkg. Discount Net Ea. TW 1/4TTN Nylon 1/4" Male 100 25% $ .53 SS 12094NY Nylon 1/4" Female 100 10% .86 SS 1/8TTB Brass 1/8" Male 100 10% 1.24 SS 1/8TB Brass 1/8" Female 100 10% 1.24 SS 1322 Brass 1/4" Male 100 10% 1.26 SS 1321 Brass 1/4" Female 100 10% 1.27 SS 1/4TTSS Stainless 1/4" Male 100 10% 8.45 SS 1/4TSS Stainles 1/4" Female 100 10% 8.49 * Discount if Purchased in Standard Package.

Part No. Net Ea. SS QJ4676-1/4CEL Threaded Cap, 1/4" FPT with Gasket .............. $ 1.26 SS QJ19843CELR Blank Cap With Gasket.................................... 1.26 SS QJ4676-45-1/4 45° Quick TeeJet Cap, 1/4" FPT....................... 2.42 SS QJ4676-90-1/4 90° Quick TeeJet Cap, 1/4" FPT....................... 2.91 SS 19438EPR Single EPDM Gasket for QuickJet Caps.......... .31 SS 19438VI Single Viton® Gasket for QuickJet Caps........ 1.33 SS PK19438EPR Pkg. of 12 EPDM Gaskets for QuickJet Caps 5.46 SS PK19438VI Pkg. of 12 Viton® Gaskets for QuickJet Caps 15.30 SS 18999EPR EPDM Gasket................................................... .62

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES • OMAHA, NE

XR -10 Thru -20

Turbo Flood Jet

— Available In 8 Colors —

COLOR-CODED “QUICKJET” CAPS

TT -01 Thru -08

**Also use with Turbo TwinJet, AIXR TeeJet & OC TeeJet (01-08)

D

QJ4676-1/4CEL TeeJet Adapter 1/4” FPT Outlet

Caps are supplied less Gaskets

Use With Spray Tips: Standard -0067 Thru -08

Cap Lug

19438EPR (EPDM)

Color Code of Quick TeeJet Caps

QuickJet Caps Less Gasket

D

QJ-1/4TNYB TeeJet Adapter

Seat Gasket

1/4” MPT Inlet QJ-1/4TTNYB Cap Adapter

D

144

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0644


Ceiling & Wall Booms

145 3/8” FPT

STAINLESS STEEL BOOMS

23"

Heavy-Duty / High Quality

D

Stainless Steel Spring Booms. Spring design allows for limited pull down to reduce vandalism or accidental damage. Available in three different mounting styles: "Spider Mount": Ceiling brackets have 23" center to center bolt pattern, (360˚ boom).

3/8" FPT

No. D360S Spider Mount

"Flush Mount": Ceiling plate is 8" x 8" with holes on 6" centers. (360° boom).

73" All booms are designed so that your high pressure hose runs down through the mounting plate and into the inner chamber of the boom, thus keeping the hose from being exposed. Bushing seals never need grease. Booms are standard with a 3/8" coupling at the end of the arm to attach your existing wand hose. All booms are completely 304SS except for the springs which are chrome plated steel. Note: 3/8" 90˚ swivel , 3/8" 90˚ St Ell & boom hose are not included and must be ordered separately.

3/8" FPT

"Flush Mount": Wall plate is 6" x 7" with holes on 4" centers. (180° boom). 3/8" FPT

D

No. D360FC Flush Mount Ceiling 3/8" FPT

3/8" FPT

3/8" COUPLING D

Standard booms are 73" overall length. Truck bay booms are 90" overall length. Note: Boom hose & 90˚ 3/8" swivels are not included. (Special 10' double-spring booms are also available in all styles at approximately twice the single spring prices.)

No. D180FW Flush Mount Wall 3/8" FPT

3/8" FPT

73"

Part No. DD D360S DD D380ST DD D360FC DD D380FCT DD D180FW DD D190FWT

Description - Booms Length Wt./Lbs. Net Ea. Ceiling Boom, Spider Mount, 360˚ 73" 20 $ 364.50 Ceiling Boom, Spider Mount, 360˚ 90" 25 369.00 Ceiling Boom, Flush Mount, 360˚ 73" 19 364.50 Ceiling Boom, Flush Mount, 360˚ 90" 24" 425.00 Wall Boom, Flush Mount, 180˚ 73" 20 362.00 Wall Boom, Flush Mount, 180˚ 90" 25 375.00

Part No. AA 7030 AA 7035 SS 36560-3/8 AB 116A-3/8 GA 6CT-6 GA 6CT-8

Description - Accessories Net Ea. Brass Swivel R.A., 3000 PSI......... $ 23.00 S.S. Swivel R.A., 5000 PSI ........... 29.80 90˚ Boom Swivel............................ 27.95 Brass 3/8" St Ell, 1000 PSI............ 2.59 3/8" x 71" Hose Assembly, 73" Booms 10.60 3/8" x 88" Hose Assembly, 90" Booms 11.95

MAXI-FLEX CEILING & WALL BOOMS D

Model 3500

Model 3500

Model 1500 Base D D

Constructed of a newly developed Space Age stainless steel alloy. This Boom is virtually indestructible and offers the ultimate in flexibility. The boom arm is stainless steel rod and can actually be pulled down 45 degrees and will “flex” back without damage. All boom parts are stainless steel, brass or aluminum. Maximum of 160° F. and 2000 PSI. Standard with a quality ball bearing swivel (repairable), and a high quality trunnion bearing in the base. Two-piece construction allows for ease in installation. Mounting base is designed to retrofit to common hole patterns. A heavy manifold at the end of the boom arm attaches the boom hose and the boom arm so that the hose cannot be pulled off. Available in either 360° ceiling booms or in 180° wall booms. Either style is available in either 6' or 8' lengths. Ports are 3/8" FPT. Inlet port can be accessed from either top or side of boom base. Flush Mount

Spider Mount

Part No. DD D360-FLTS DD D360-SPTS AA 7030 AA 7035 SS 36560-3/8 AB 116A-3/8 GA 6CT-7

SW504A-L

Part No. FL OHS-1500 FL OHS-1500-8 FL OHS-3500 FL OHS-3500-8 FL SW504A FL SW504A-L FL RK550 FL OHS-HB GA 6CT-5

TWIN SPIN CEILING BOOMS 3/8" FPT

3/8" FPT

(800) 228-9666

Stainless "Twin Spin" Booms are designed to travel under each other which allows 2 different products to be used in the bay. These heavy duty booms are designed with slanted arms to travel in a 360 degree range and not hang up. Bushing seals never need grease. Booms are sold separately and are available with Flush or Spider mount brackets.

Description - Accessories Net Ea. Flush Mount Boom..................... $ 299.00 Spider Mount Boom................... 299.00 Brass Swivel R.A., 3000 PSI...... 23.00 S.S. Swivel R.A., 5000 PSI ........ 29.80 90˚ Boom Swivel........................ 27.95 Brass 3/8" St Ell, 1000 PSI......... 2.59 3/8" x 75" Boom Hose Assembly 10.95 DULTMEIER SALES • OMAHA, NE

Length WT. Net Ea. 180° Boom 5-1/2' 14 lbs. $ 279.00 180° Boom 7-1/2' 14 lbs. 324.00 360° Boom 5-1/2' 14 lbs. 279.00 360° Boom 7-1/2' 14 lbs. 352.00 Replacement Swivel, Straight ............. 18.65 Replacement Swivel, Elbow................. 31.95 Swivel Repair Kit ................................. 8.25 Boom Arm Block.................................. 41.95 Replacement Boom Hose - 64"............ 9.42

Booms are 304 Stainless Steel except for springs which are chrome-plated. Rated to 2000 PSI. Overall length is 5'9". Two booms are required per bay. Swivel and hose options are shown at left and must be ordered separately. •

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0091


Ceiling & Wall Booms & Accessories

146

Zierden 360˚ Overhead Offset Boom

ESB100

CAR WASH SAFETY BOOM and SWIVEL ASSEMBLY

D

ZiercoWater Boy 360˚ Overhead Offset Boom offers close boom spacing for efficient foaming brush operation. Makes wash bays more convenient by having hoses overhead that swing freely around vehicles. Heavy duty construction resists corrosion. Boom hose and inlet hose are included. Part No.

Net Ea.

ZI ESB20C Overhead Offset Boom, 5’ Arm Model ESB Swivel Boom is ideal for heavy commercial use in coin-operated car washes, service bays and in car and truck fleet cleaning departments.The boom permits 360° of free and easy swivel rotation around a vehicle in an 11 foot diameter. Heavy gauge all steel mounting base, non-corrosive metal internal parts and double ram ball bearings for effortless boom swing. Boom length is 5 or 8 feet. Pressures to 3000 psi. Extensions are also available.

STAINLESS STEEL WALL BOOMS Stainless Steel Booms for wall mounting. 180° swing coverage. Booms are constructed of 304 stainless. Discharge couplings are 3/8" OR 1/2” FPT. Simple bracket design allows for wall mounting without the need for bearings. D

Automatic Return Option Auto Return Feature can be used on 204 & 206 Models. Boom springs back to predetermined location.

$ 329.50

No. 27234

3/8” FPT Outlet

Model 27234 is designed so that hoses are to be inserted inside the boom. This allows for either high or low pressure applications. (Hoses are ordered separately). Length is 72". 1/2" FPT Inlet

A8401 Bumper

CS204ARS 1/2" FPT Outlet

No. D885

Model D885 Compact Boom is designed so that solution runs inside the boom channel (Low pressure only). For systems such as Brush or Triple Wax. Length is 41". Bumper included. D

20401 Replacement Seal Elbow

D

104A Cartridge

204B Conversion Kit

1/2" FPT Inlet

A8401 Bumper 1/2" FPT Outlet

D

Part No. Net Ea. ZI ESB100 Complete Ceiling Boom Assembly: Includes Boom Body and Swivel Assembly, Inlet Hose, Boom Arm Hose, Swivel, 5' Long Boom Arm, 350˚ Design ........................................... $ 289.50 ZI ESB100-8 Same as ESB100 but with 8' long boom arm........................ 290.00 ZI ESB100D Same as ESB100 but with wall mount bracket for 180° use.. 292.00 ZI CS204ARS Auto Return Assembly As Add-On......................................... 130.00 ZI 204B Conversion Kit Converts old style “SB” booms with 104A sealed cartridges to the new style “ESB” booms with the 20401 Elbow............................................................. 128.50 ZI 204C O-Ring Kit for 20401 Elbow, booms prior to 7/92................ 5.36 ZI 204C-N O-Ring Kit for 20401 Elbow, booms after 7/92.................... 4.36 ZI 20401 Replacement Seal Elbow for 204 easy-service cartridge.... 24.00 ZI 104A-1/4 * Cartridge for old style “SB” 203 Boom - 1/4"...................... 92.95 ZI 104A-3/8 * Cartridge for old style “SB” 203 Boom - 3/8"...................... 92.95 ZI 20007 Boom Arm Only .................................................................. 16.40 ZI 20008 Boom Spring Only ............................................................. 8.17 * Note: Zierden swivels should use Sil Glyde silicon base grease for maintenance. Using other lubricants might cause seal failure.

No. D883ASSY

Model D883 Standard Length Boom is designed so that solution runs inside the boom channel (Low pressure only). For systems such as Brush or Triple Wax. Length is 72". Bumper included. Part-No. Wt. Net Ea.

DU 27234 SS Wall Boom, 72".................... 12 lbs. $ 115.50 DD D885 SS Wall Boom, 41".................... 12 lbs. 107.50 DD D883ASSY SS Wall Boom, 72".................... 12 lbs. 109.50 GA 4CT-7 7' High Pressure Hose, 27234..................... 11.50 DU 4B-7 10' Low Pressure Hose, 27234.................... 13.50 DD A8401 Bumper as replacement for DB885 & D883. 4.96

Boom Hose Assemblies 5' - 18' Lengths

– BLACK HOSE ASSEMBLIES –

Part No. GA 4CT-12 GA 4CT-15 GA 4CT-18 GA 6CT-5 GA 6CT-6 GA 6CT-7 GA 6CT-8 GA 6CT-12 GA 6CT-15 GA 6CT-18

Visit Our Online Store Anytime. Anywhere.

I.D. LENGTH FITTED 1/4" 12' 3/8" MPT 1/4" 15' 3/8" MPT 1/4" 18' 3/8" MPT * 3/8" 5' 4" 3/8" MPT * 3/8" 5' 11" 3/8" MPT * 3/8" 6' 3" 3/8" MPT * 3/8" 7' 4" 3/8" MPT 3/8" 12' 3/8" MPT 3/8" 15' 3/8" MPT 3/8" 18' 3/8" MPT

D

Available in Black or Blue

Wire braid hose assemblies in 1/4" & 3/8" sizes for pressures to 3000 PSI. All hoses are fitted 3/8" MPT solid both ends with a hose saver sleeve on one end. Rated to 250° F. Smooth Cover.

WORKING PRESSURE 3000 PSI 3000 PSI 3000 PSI 3000 PSI 3000 PSI 3000 PSI 3000 PSI 3000 PSI 3000 PSI 3000 PSI

Net Ea. $ 15.30 17.55 18.00 9.42 10.60 10.95 11.95 17.85 19.85 22.40

– BLUE NON-MARKING HOSE ASSEMBLIES –

dultmeier.com

DU 4BL12 1/4" 12' DU 4BL15 1/4" 15' DU 4BL18 1/4" 18' DU 6BL12 3/8" 12' DU 6BL15 3/8" 15' DU 6BL18 3/8" 18'

3/8" MPT 3/8" MPT 3/8" MPT 3/8" MPT 3/8" MPT 3/8" MPT

3000 PSI 3000 PSI 3000 PSI 3000 PSI 3000 PSI 3000 PSI

$ 15.95 16.65 19.35 18.50 20.75 23.35

* No Hose Savers on These Sizes.

5% Discount On 10 or More Assorted Hoses. DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0090


Booms

147

Stainless Steel Ceiling Booms High Quality Stainless Steel Ceiling & Wall Booms from Mosmatic. All booms include hose with guard and swivel and are ready for installation. Two designs to choose from. All booms are standard with ball bearing swivel axle. Many length sizes to choose from. All booms are rated to pressures of 4000 PSI and temperatures to 200° F. Inlet and outlet fittings are 3/8" FPT. Mounting plates are 7" x 7" with bolt holes on 6" centers. Part No. MM 66019 MM 66029 MM 66039 MM 66049 MM 66059 MM 66069 MM 66079 MM 66089 MM 68519 MM 68529 MM 68539 MM 68549 MM 68559 MM 68569 MM 68579 MM 68589 MM 65911 MM 43259 MM 30014

Style Length Wt. Ceiling 5’ 3” 21 lbs. Ceiling 5’ 9” 22 lbs. Ceiling 6' 3" 23 lbs. Ceiling 6' 9" 24 lbs. Ceiling 7' 5" 24 lbs. Ceiling 8' 2" 25 lbs. Ceiling 9' 26 lbs. Ceiling 9' 10" 26 lbs. Wall 5' 3" 24 lbs. Wall 5' 9" 26 lbs. Wall 6' 3" 27 lbs. Wall 6’ 9” 29 lbs. Wall 7’ 5” 31 lbs. Wall 8’ 2” 33 lbs. Wall 9’ 35 lbs. Wall 9’ 10” 35 lbs. Positioning Magnet Assembly Upgrade Swivel Kit for 4000 PSI @ 250° F................. Boom Swivel, 3/8" F x 1/4" F.

Boom Hose with Swivel are standard

Ceiling Booms D

Ball Bearing Axle

CALL for PRICING

D

Wall Booms

Dual Ceiling Booms Stainless Steel Dual Ceiling Booms are designed with two separate booms and two entrance points so that one line can be high pressure and one low pressure, or 2 high pressure if desired. One mounting plate means ease of assembly. Booms include swivels and boom hoses. Sold in sets of 2 booms, one is 6" shorter than the other. Inlet is 3/8" FPT. Rated to 2200 PSI and 200° F. Part No. MM 67429 MM 67439 MM 67449 MM 67459 MM 30014

D

Style Length Wt. Dual 5' 9" & 6' 3" 42 lbs. Dual 6' 3" & 6' 9" 43 lbs. Dual 6' 9" & 7' 5" 44 lbs. Dual 7' 5" & 8' 2" 45 lbs. Boom Swivel, 3/8" F x 1/4" F........

CALL for PRICING

“Z” Booms Stainless Steel “Z” Booms from Mosmatic. Unique design allows for both booms to be mounted to the ceiling for 360° coverage. Bent, “Z” design allows for one boom to move under or over the other boom. With this setup, you can offer high pressure from one boom and foam brush or triple foam wax from the other thus eliminating a wall boom. Construction is brushed stainless. Polished stainless is also available. Inlet is 3/8" FPT. Booms are standard with boom arm hose and boom swivel. Rated to 4000 psi and 200° F. Available in different lengths to meet your bay requirements. No. 65911 is a magnetic positioning unit to keep boom fixed in one position when customers are finished in bays. Triple Z Booms

D

D

Mounting Options Need extra clearance for your Mosmatice ceiling Boom? Drop Down Stems will lower booms up to a total of 25" from the ceiling. No. 19019: 8" Extension Package for Mosmatic ceiling booms P-Series. No. 19020: 16" Extension Package for Mosmatic ceiling booms P-Series.

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

65911

www.dultmeier.com

Part No. Length Weight MM 65009 SS Boom 4' 9" 21 lbs. MM 65019 SS Boom 5' 1" 23 lbs. MM 65029 SS Boom 5' 5" 24 lbs. CALL for MM 65039 SS Boom 5' 9" 25 lbs. MM 65911 Positioning Magnet Assembly. PRICING MM 19019 * 8" Extension Package.......... MM 19020 * 16" Extension Package........ * When Ordered with Booms

• DAVENPORT, IA

(800) 553-6975

E0092


Truck/Bus Wash Booms • Hose Trolley

148

TRUCK / BUS WASH BOOMS Wall Mount, Stainless Steel Booms for extended reach up to 78’. Two-piece assemblies are made up of a 180 degree wall boom extension and a 360 degree ceiling boom. Available in 18’ 10” for smaller trucks or 38’ 2” for full size semi-trailers. The large unit will effectively cover 76’ and allow washing without moving the vehicle. Water inlet to boom extension is 3/8” FPT. Booms come with boom hose and 3/8” swivels rated to 4000 PSI.

Boom Connection

Heavy Wall Plate D

3/8” FPT Inlet

Bolt Plate

9’ 10” or 19’ 7”

Bolt Plate

Boom Hose with Swivel

D

9’ or 18’ 7”

E20 Shown As Assembled

Part No.

Length

Wt.

MM E20 MM E30 MM E38

18’ 10” 28’ 8” 35’ 6”

100 lbs. 180 lbs. 220 lbs.

Stainless Truck Boom Stainless Truck Boom Stainless Truck Boom

CALL for PRICING

HOSE TROLLEY SYSTEM Dual Cable Trolley System for wash bays. Keeps hoses from dragging and free moving to eliminate kinking. No booms are required. Reduces hose damage and increases worker safety. System includes (8) trolley units along with enough galvanized cable, cable clamps, turnbuckles and wall eyebolts for up to 100’ on each side of the vehicle. Hose trollies ride on the cable for free movement back and forth in the bay. (Hoses are not included).

Existing Wall Bracket Not included

Part No.

DU TROLLEY

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

Net Ea.

Wash Hose Trolley System

• DAVENPORT, IA

(800) 553-6975

$ 810.00

E0773


149

Air Dryers • Vacuum/Blowers • Jump Ramp Vacuum / Blower Unit

Warm Air Dryers Warm Air Dryers for cars, vans, trucks even pets. Ideal for auto and motorcycle detailing. Great for hard-to-reach places where towels and chamois can’t reach. Cuts drying time up to 80%. Models shown are 110 volt but 220 volt also available. Completely safe because nothing but air touches the vehicle surface. Warm, dry filtered air is heated from the motors themselves to approximately 30° F. above ambient temperatures. Available in 3 models to meet any application. All models feature powder-coated, enamel finish and rugged, all steel construction.

SK-1 Sidekick is a small hand held dryer that is ideal for small touch up jobs. Great for motorcycle drying. Cuts drying time by 70%. Nothing but air touches the vehicle surface. Single motor develops 85 CFM. Includes (2) nozzles and 1’ power cord, (no hose). Rated to 8 amps.

SK-1 Sidekick

U n i q u e Va c u u m / Blower / Dryer Unit. Wall mounted detailing vacuum that can also be used as an air blower. Great for detail shops, auto dealers, truck and car garages. 4 HP motor is rated to 95” water lift and 130 CFM. Unit comes with a full range of accessories, including 24’ of hose. All steel construction with powder-coated finish. Permanent cloth dust bag with easy change foam filter. Rated for 120 volt, 11 amps. Dimensions are 36” L x 10-1/2” H x 7” W. Dry pickup only. Part No.

D

GS HRS-83BA

Wt.

Portable Vacuum / Blower

- Hand Held -

B3-CD Blaster

Vacuum / Blower / Dryer Hand Held Unit. This powerful little model is rated to 60” water lift and 70 CFM. All steel construction with powder-coated finish. Available in 120 volt or 12 volt models. 110 Volt Unit is rated to 500 watts, 4.5 amps. 12 Volt Unit will operated from any 12 volt receptacle in car or truck. Both models come with 19” hose, crevice tool, dust brush, upholstery nozzle, 20” extension and extra filter bags. Dry pickup only. Part No.

Wt.

Net Ea.

GS VM12500 Vacuum/Blower, Hand Held, 120 Volt 6.5 lbs. $ 69.85 GS AM12IDA Vacuum/Blower, Hand Held, 12 Volt 6.5 lbs. 69.95 GS DVP26 Disposable Filter Bags, Pack of 5...................... 3.95

MB-3CD Master Blaster

MB-3CD Master Blaster is the largest unit. Includes wheels for added portability. Optional wall bracket is available for wall mounting or storage if needed. (2) motors develop 228CFM. Rated to 18 amps. Includes 12’ power cord, 10’ blower hose, blower nozzle and (5) different nozzle attachments.

D

Net Ea.

$ 269.00

29 lbs.

Vacuum / Blower Units

B3-CD Blaster is a small hand carry dryer for portability. Single motor develops 130 CFM with 2 stage dual fan. Rated to 10 amps. Includes 12’ power cord, 10’ blower hose, blower nozzle and (5) different nozzle attachments.

D

- Wall Mount -

Jump Ramp

D

Heavy Duty Jump Ramp allows you to quickly get vehicles back on the conveyor when jump-offs occur. Works on either side of the rail. Welded aluminum construction for long life and performance. Designed to fit under the front or rear of the tire to allow for forward or reverse of the vehicle to get it back onto the conveyor. Reduces down time and quickly gets your conveyor back up and running. MBP3 Master Blaster Pet Wash Unit. Includes the Master Blaster Unit above but is mounted on an aluminum base with electrical panel for remote mounting on wall or in attic. Electrical panel is prewired and includes transformer with relays for remote startup. (Can be wired to your bay meter or remote stop/start switch which is also available). 10’ and 15’ hoses and nozzles are included.

Comes with a wall hanger bracket for easy access. Rubber grips prevent slippage. Works on any height conveyor guide rails. Can also be used for automatic car washes. Dimensions: 9” wide x 28” long x 4-1/2” high. (Overall length with rubber grips is 36”).

D

MBP3 Pet Wash Dryer Unit

Part No.

Dryer Model

GS SK-1 GS B3-CD GS MB-3CD GS MVC-331 DU MBP3

Sidekick 1 85 3 lbs. $ 73.10 Blaster 1 130 8 lbs. 180.00 Master Blaster 2 228 16 lbs. 319.50 Wall Bracket for MB-C3D................................. 17.00 Pet Wash Dryer Unit 2 228 25 lbs. 1111.00

Motors

CFM

DULTMEIER SALES • OMAHA, NE

Wt.

Net Ea.

(800) 228-9666

D D

Part No.

DU JR25

www.dultmeier.com

Wt.

Aluminum Jump Ramp

• DAVENPORT, IA

16 lbs.

(800) 553-6975

Net Ea.

$ 269.00

E0983


Air Booms • Drying Systems “Blasto-Dry” Vehicle Drying Systems

150

Inbay Air Dryers

Blasto-Dry Vehicle Drying Systems are designed for added revenue and customer satisfaction in your self-serve bays. Patent pending, air knife tool quickly strips water from the vehicle surface. Also ideal for full serve washes and detail shops.

Inbay Air Dr yers from Mosmatic. Great new revenue source for your self-serve bays. Universal drying system can be used for cars, trucks, motorcycles and Wand even boats. Designed for wall or ceiling installation. Blow drys vehicles with spot free results.

2” x 15’ Hose

D

Systems Include: Illuminated domes are blue in color (red & yellow colors are available on special order) • Air wands • 2” x 15’ hose • Wand holder • Bay instruction signs • (2) Blower motors require, 25 amp, 110 volt service per bay. 13 Amp on 220 volt. Booms are not included. See the wide variety of Mosmatic Air Booms to fit your needs.

Part No. MM 60397 110 Volt Mosmatic Dry System MM 60396 220 Volt Mosmatic Dry System Standard Features: Stainless Steel Cabinet with Laser cut, backlit graphics • Special designed dual blower motors for optimal air flow and pressure • Air knife tool for maximum water removal • 2” x 15’ I-helix hose with rotating cuff eliminates snagging on fenders, antennas and trim • Weld-on hose cuff eliminates separation • Stainless wand holder • Colorful bay signs.

Wt. CALL for 65 lbs. PRICING 65 lbs.

Stainless Steel Air Booms The ideal boom for use with air dryers, vacuums or air blowers. Swiss polished stainless steel construction. 180 Degree Wall Mount or 360 Degree Ceiling Mount. Inlet and outlet is 2". All booms come with mounting plates. All booms are 5' in length.

Specifications: SS Cabinet is 18” wide x 12” deep x 28” high, weight is 70 lbs. Voltage is 120 or 220 volts, 60 hz. (2) Blower motors are 13 amps at 110 volts each. D

#60310 Ceiling Mount, Side Inlet

#1000 w ith #60311 Boom

D

#60313 Ceiling Mount, Top Inlet #60314 Optional 90° Elbow D

#60326 360° Air Boom

Systems are available 3 different ways: Model 1000 is designed for wall mounting in the bay. Model 1001 is designed for pole mounting on islands or in bays without solid walls.

D

#60311 Wall Mount

Model 2000 is designed for attic mount above bays.

Note: Air Booms for ceiling or walls are optional depending on style and mounting requirements. These are shown and priced separately. Part No.

Type

Voltage

Wt.

Net Ea.

CF 1000 Inbay Wall 110V 70 lbs. CF X1000 Inbay Wall 220V 70 lbs. CF 1001 Inbay Pole 110V 70 lbs. CF 2000 Attic Mount 110V 70 lbs. CF X2000 Attic Mount 220V 70 lbs. Note: Quantity Discounts are Available. DULTMEIER SALES • OMAHA, NE

$ 1167.00 1167.00 1222.00 987.00 987.00

(800) 228-9666

Part No.

Boom Type

MM 60310 MM 60313 MM 60324 MM 60326 MM 60311 MM 60320 MM 60314

Ceiling, Side Inlet 18 lbs. Ceiling, Top Inlet 18 lbs. Z Boom, Side Inlet 18 lbs. Z Boom, Top Inlet 18 lbs. Wall Mount 18 lbs. Cable & Retractor for Hose.... 90° S.S. Elbow........................

www.dultmeier.com

• DAVENPORT, IA

Wt. CALL for PRICING

(800) 553-6975

#60320 Retractor

E0720


Air Shammee Drying Systems

151

A Great Revenue Source! Air Shammee Drying System is a high velocity vehicle dryers for vacuum islands or bays. Hand held, touch-free drying. Customer love them. Free standing units come complete with coin meter, pedestal, hose and trigger air wand. Bay units can be mounted on wall in bay or in ceiling attic above bays. Bay units are designed to be wired into your existing coin meters. Stainless wall booms are not included with 2900 models. All units are standard with (3) blower motors for superior air flow. (110 volt, 40 amp service required - 220 volt also available). I2900 Bay System includes: Hose and unique trigger air wand • Lighted dome, (red, yellow or blue) for wall or ceiling mount • Triple motor blower system • (Stainless wall or ceiling booms not included). I2900A Bay System. Same as I2900 above but designed to mount in attic. Dome and light are not included but all other features are the same. P2500 Stand alone pedestal unit features the following: 14 gauge stainless canister, (27” high) • 30” Painted steel pedestal • Stainless coin meter with timer • Red, yellow or blue plastic domes • Unique trigger air wand • Bay signs. C2300 Combination Dryer & Air Machine Unit. Allows customer to fill tires or blow dry from same system. Includes pedestal for island mounting. Coin meter, blower hose and air hose are included. Customers can access either function from the same coin meter. 60311 Wall Boom Optional

D

I2900 Bay Unit with Optional 60311 Boom

D

TR5 Trigger Nozzle

D D

1FAN Fan Nozzle (Optional)

C2300 Combo Unit with Wand

D

60326 Ceiling “Z” Boom

D

DULTMEIER SALES • OMAHA, NE

Part No. AS I2900 AS I2900A AS P2500 AS C2300 AS RV5 AS TR5 AS 1FAN MM 60311 MM 60326

(800) 228-9666

P2500 Air Shammee Pedestal Unit Description Wt. Net Ea. Air Shammee Inbay Unit, Wall Mount.................... 60 lbs. $ 1375.00 Air Shammee Inbay Unit, Attic Mount.................... 56 lbs. 1252.00 Air Shammee, Stand Alone Unit with Pedestal...... 165 lbs. 2099.00 Air Shammee, Combination Dryer & Air Machine.. 235 lbs. 2904.00 Air Relief Valve as replacement............................. 2 lbs. 91.70 Trigger Nozzle as replacement.............................. 1 lb. 105.00 Fan Nozzle for TR5 Trigger Wand as Option.......... - 44.60 Stainless Steel Wall Boom, Mosmatic.................... - 375.00 Stainless Steel Ceiling “Z” Boom, Mosmatic.......... - 390.50

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0721


Hot Air Dryers • Booms

152

Hot Air Turbo Dryers Now an Air Dryer System featuring Hot Air! Turbo Towel from J.E. Adams is designed for inbay or island use. Available for wall mount in bays, free standing pedestal unit or vacuum/dryer combination for vac islands. Quickly dries vehicles surfaces as well as floor mats and carpets. Blasts water from door locks, cracks and crevices as well as from wheels and engine areas. Standard Features include: One high performance blower motor for high air flow • Thermostatically controlled, internal heating unit heats air to 120° F. above ambient temperature • Nozzle velocity exceeds 200 MPH • 2” x 30” High temperature hose with wand • ETL Listed. (Note: Booms are not included, choose from the many options shown below).

Three Different Turbo Towel Options to Meet Your Specific Needs!

Pedestal Models

D

Pedestal Models are designed to mount on a vacuum island or a separate drying island. These units are coin activated and also have a bill acceptor option. 110 volt. Large digital countdown timer is also included. Medeco door locks and pin lock on coin boxes are included for added security. Dimensions are 29” wide x 14” deep x 56” high. 17000V-8819

Part No.

Coins

AA 17000-8819 AA 17000V-8819

Bills

Volts

Wt.

Yes No 110 Yes Yes 110

Net Ea.

190 lbs. 192 lbs.

$ 2680.00 3357.00

Combo Units Combo Units. Turbo towel dryer and (3) motor vacuum offers drying and vacuuming from one machine. Lighted domes in a wide variety of colors. Coin mechanisms will accept coins or tokens. Mars bill acceptor is also a standard feature. 2” x 30’ dryer hose and 2” x 15’ vacuum hose are included. Medeco locks for added security. Dimensions are 19” wide x 28” deep x 53” high.

Inbay Models Inbay Models are designed to be activated from your bay coin box. This allows another function to be offered in the bay which extends customer total time in the bays meaning more revenue for you. Available in either 110 volt or 220 volt models. Dimensions are 10” wide x 10” deep x 19” high.

D

Part No.

Volts

AA 18000 AA 18000-220

110 220

Wt.

Net Ea.

60 lbs. $ 1328.00 60 lbs. 1378.00

18000

D

9215LDV

Part No.

Coins

AA 9215LDV

Bills

Volts

Yes Yes 110

Wt.

278 lbs.

Net Ea.

$ 4003.00

#60314 Optional 90° Elbow

Stainless Steel Air Booms D

The ideal boom for use with air dryers, vacuums or air blowers. Swiss polished stainless steel construction. 180 Degree Wall Mount or 360 Degree Ceiling Mount. Inlet and outlet is 2". All booms come with mounting plates. All booms are 5' in length.

#60326 360° Air Boom

#60311 Wall Mount

D

D

#60310 Ceiling Mount, Side Inlet

D

#60313 Ceiling Mount, Top Inlet

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

Part No.

Boom Type

MM 60310 MM 60313 MM 60324 MM 60326 MM 60311 MM 60320 MM 60314

Ceiling, Side Inlet 18 lbs. Ceiling, Top Inlet 18 lbs. Z Boom, Side Inlet 18 lbs. Z Boom, Top Inlet 18 lbs. Wall Mount 18 lbs. Cable & Retractor for Hose.... 90° S.S. Elbow........................

www.dultmeier.com

• DAVENPORT, IA

Wt. CALL for PRICING

(800) 553-6975

#60320 Retractor

E0914


Surface Cleaners • Water Brooms

153

WATER BROOMS

UnderCarriage Cleaners D

Undercarriage Cleaners from Mosmatic! High quality, Swiss Stainless Steel construction with Swiss engineering. Ideal for use on cars, trucks, construction or agricultural equipment. Only requires 10” of clearance. Available in two styles: low profile with standard nozzles or high profile with stabilizer nozzles for maximum cleaning power. 21” or 30” sizes. Rated to 4000 PSI and 250° F. Trigger wand handle, feeder hose and nozzles are included. Overall length is 42” and height is 38” on all models. Guard plates are optional.

No. 80611

No. 100870

Shown with Optional Extension

D

Ideal for

(High Pressure)

Stainless Steel Water Brooms with heavy duty casters for driveway and parking lot cleaning. 12" and 16" widths available. Rated to 4000 psi. Extensions are not included. Inlet is 1/4" quick coupler. Nozzles are included.

Part No. Width

Guard Plate

Cars, Trucks,

Nozzle Max. Ports PSI

IP 100869 12" IP 100870 16"

Agricultural & Construction

Net Ea.

3 4000 $ 27.75 4 4000 32.50

No. 80613

Equipment

D

WATER BROOMS (Low Pressure) D

Part No.

MM 80611 MM 80613 MM 80612 MM 80614 MM 80621 MM 80622

Nozzles

The ideal tool for removing gravel and debris from parking lots, driveways and sidewalks. Water flow is directed forward through the jets as you walk. Gravel and trash are pushed ahead.

Wt.

21” Cleaner (2) 1/8” #3 21” Cleaner (2) #3 Stabilizer 30” Cleaner (3) 1/8” #3 30” Cleaner (3) #3 Stabilier 21” Guard Plate - 30” Guard Plate -

27 lbs. 33 lbs. 31 lbs. 36 lbs. 7 lbs. 9 lbs.

CALL for PRICING

Whirl-A-Way Surface Cleaners Heavy-Duty Surface Cleaners for high pressure cleaning of driveways, parking lots, sidewalks, warehouse floors, etc. Designed to handle up to 4000 PSI and 8 GPM supplied from your existing pressure washer. Heavyduty, yellow canister or stainless dome supports high quality swivel and arm assembly. Available in 16" to 24" sizes with caster wheels. Rated to 180° F. Units are complete with trigger wand, handle, nozzles and feeder hose. Units come with dual arms for (2) nozzles except the 24" model which features a Tri-arm for (3) nozzles.

Manufactured with specially extruded, high temper, 3/4" aluminum pipe and heavy duty brass fittings. Pistol grip valve for flow control. Rust proof, ball bearing swivel casters. Available in a variety of spray widths. Designed for garden hose feed supply at 60-75 psi. (Hose not included). Handle is 48”. Part No.

Spray Width

SF BB24 SF BB32 SF BB40 SF BB48 SF BB56

24" (6 jets) 32" (8 jets) 40" (10 jets) 48" (12 jets) 56" (14 jets)

Net Ea.

$ 115.50 124.00 128.00 132.00 137.00

Wands are Included

Roof Cleaner 2000WAWS & 2400WAWS

High Pressure, Stainless Steel Roof Cleaner. Allows the operator to clean a wide variety of roof surfaces. Wheels are adjustable for height and width for stability and safety. Standard with 2 rotor arms. (15° Nozzles need to be ordered to match your flow rate). Includes safety eye to secure unit with rope or cable.

Canister Wheel Style

Rated to 4,000 PSI and 250° F. Pan housing is 21” diameter. High pressure shut-off valve and pressure gauge are also included. Inlet port is 3/8” FPT

D

D

1600WAW

D

D D

Part No.

BE 1600WAW BE 1800WAW BE 2000WAW BE 2000WAWS BE 2400WAWS

Canister

Wheels

Wt.

16" Poly 18” Poly 20" Poly 20” Stainless 24” Stainless

Yes Yes * No Yes Yes

30 lbs. 33 lbs. 36 lbs. 38 lbs. 40 lbs.

Net Ea.

$ 265.00 349.00 319.00 498.00 598.00

Part No.

MM 80658

* No Wheels, Brush Skirt Only. DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

Diameter

Max. PSI

Wt.

21”

4000

32 lbs.

• DAVENPORT, IA

(800) 553-6975

CALL for PRICING E0781


Surface Cleaners

154

Stainless Surface/ Pavement Cleaners 80775

82154

Surface Cleaners from Mosmatic are perfect for cleaning parking lots, shop floors, sidewalks or any other large surface. High RPM swivels and nozzle arms guarantee long lasting operation under tough conditions. Completely Stainless Steel construction. Trigger spray wand and high pressure connector hose are standard. Units are rated to either 2500 or 4000 psi and 250° F. 1/8” 1503 nozzles are also included.

82154WH

D

D

D

Model 78272 is a 12” economy cleaner for light duty jobs. Standard with three caster wheels, trigger wand, extension and adjustable toggle joint. Rated to 2500 PSI. Model 82154 is a 21” wide cleaner without wheels. This unit is designed to “float” on the surface similar to a “hovercraft” when pressure is on. Sturdy brush guard eliminates overspray. Rated to 4000 PSI. Model 82154WH (21”) and 19501WH (30”) are standard with four permanently attached caster wheels for easy maneuvering. Rated to 4000 PSI. Model 80774 (21”) and 80775 (30”) feature four adjustable caster wheels that can be raised or lowered for different impact ranges and cleaning needs. Rated to 4000 PSI.

D

Model 78250 is a hand held model with a 8” pan. Wand and handle are included. Rated to 2500 PSI.

19501WH 78250 78272

Pan Part No. Wheels Diameter

MM 78272 Yes 12" MM 82154 No 21" MM 82154WH Yes 21" MM 19501WH Yes 30" MM 80774 Yes 21" MM 80775 Yes 30" MM 78250 No 8"

Wt.

9 lbs. 24 lbs. 28 lbs. 35 lbs. 31 lbs. 46 lbs. 4 lbs.

CALL for PRICING

D

D

Surface Cleaners with Recovery Systems High Quality Surface Cleaners with added Air Recovery Design. Can be hooked up to your existing vacuum to pick up waste water. No overspray or flying debris guarantees a safe, clean work area. All units include spray wand and extension where shown. The perfect tool for removing dirt, paint, grime and even graffiti from a wide variety of surfaces. Hook up to your pressure washer and wet vacuum and you are ready for most any cleaning requirement.

78285 Hand Held D

Vac Hose Recovery Port 80784

Stainless Steel Surface Shown with Cleaners with Air Recovery Vacuum Hose are available in 8” and 12” single arm and 21” and 30” double arm floor models. Air recovery port will accept 2” vacuum hose. Floor units are standard with 3 or 4 caster wheels as shown. All units are rated to 240° F. 1/8” 1503 nozzles are also included. Max. No. of Part No. Pan Size PSI Nozzles

MM 78285 MM 78292 MM 80784 MM 80785

8” 12” 21” 30”

D

78292

Wt.

4,000 2 7 lbs. CALL 4,000 2 12 lbs. for 4,000 2 39 lbs. PRICING 4,000 3 52 lbs.

DULTMEIER SALES • OMAHA, NE

D D

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0079


Credit Card System

155

CryptoPay Credit Card System A simple and economical way to accept Credit Cards in your Bays, Vacuums, Auto Cashiers, Pet Washes or Vending Machines. Easily convert existing equipment or specify on new meter systems.

Simple & Economical Way to Accept Credit Cards in Your Bays, Vacuums, Auto Cashiers, Pet Washes or Vending Machines!

As simple as drilling holes and mounting the swipers to your meters and vacuums. Swipers use a secure, wireless connection to the data coordinator in your equipment room. This coordinator can verify information from up to 30 swipers per location and then sends the encrypted data via internet service to your card service/processor. Swipers combine power supply, control and technology electronics in each unit. Push button features allow customers to stop when they wish or add time without additional card swipe. Lighted LED feature on all swipers show customers direction to swipe.

11SW CryptoPay Swiper

Accepts Mastercard, Visa, Discover and American Express. Systems can be set in the field for count up or count down mode which allows you to charge for time in the way that best suits your business. Designed for USA Domestic use only.

All in One. Every CryptoPay swiper combines the power supply, control and CryptoNet technology electronics into a single unit.

D

D

Secure.

11CR CryptoPay Coordinator

Simple. This single CryptoNet Coordinator supports all of our POS units and simply connects to your internet service.

The transaction travels across a radio mesh network to the coordinator where the information is temporarily held in the encrypted form and never “in the clear.”

CryptoPay Accepts These Cards

Count Down Sign

Count Up Sign

CryptoPay Swiper

CryptoPay Swiper

CryptoPay Swiper D D

D

Part No.

Description Net Ea.

CB 11SW CryptoPay Swiper.............................................. $ 369.00 CB 11CR Coordinator........................................................ 369.00 CB 12SN Bay Sign, Count Up........................................... 12.95 CB 12SN-1 Bay Sign, Count Down, Coin Pulse................... 27.95 CB 12SN-2 Bay Sign, Count Down, Credit Pulse................. 27.95

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E1023


TIMERS (Vacuum & Bay) Bay/Vacuum Timers

Super Timer

AT411E Timers are for use in bays or vacuums. Designed to be wired for either 24 or 110 volt operation. Accumulating feature will accept up to 15 coins to start. Adjustable from 2 seconds to 8-1/2 minutes per coin. Can easily be changed in the field for coins or time.

Replacement for “SECURECOIN From the makers of the Magikist Coin Mechanisms: SuperTimer 24/110 bay or vacuum timer. Standard Features: Up to 16 coins to start and up to 17 minutes per coin • Accumulating design for number of coins and time • Last Minute alert • "Grace Period" for 1 coin restart • Adaptable to most all popular coin acceptors • Any feature can be easily disabled if not desired • Reset switch for easy testing • 20 Amp switched output • Solid-state design.

AT411E is the base timer for bays or vacuums. Times out at end of cycle. AT411EL has additional “Last Alert” feature for use with warning horn (not included) to let customers know that cycle time is running down. AT411EX has additional “Extra Time” feature that allows for customers to “Finish” wash without starting a new cycle.

D

Part No.

AT411E

AT413 Vacuum Timer with Transformer has a unique design that allows for 110-Volt operation but also features a built-in 24-Volt transformer for use with electronic coin mechanisms. Allows for easy conversion from mechanical vacuum coin mechanisms to 24 Volt electronic mechanisms. Accumulating design allows for up to 15 coins to start and up to 8-1/2 minutes per coin.

D

Standard Bay/Vac Timer....................... $ 80.95 Timer with “Last Alert” Feature............. 93.95 Timer with “Extra Time” Feature............ 93.95 110 Volt Timer with 24-Volt Transformer 109.50 Horn for AT411EL ................................. 36.00

Designed to be used in bays or vacuums. 1-31 coins to start and are accumulating. External time and coin set switches. Fingertip time and coin switch setting. Built-in overload protection.

Part No.

UP 24400

Net Ea.

24-Volt Bay Timer ................................. $ 76.85 110-Volt Vacuum Timer......................... 147.00

from Slugbuster

An inexpensive alternative to “Digital” or “Last Alert” Timers. The Grace™ Timer allows your customers a 15 or 30 second “Grace Period” after the time cycle has expired to insert additional coins without putting in a full vend price.

Last Alert Bay Timers Last Coin Alert Timers let your customers know when time is running down. With one minute of time remaining, a pulse is sent to a horn, buzzer or strobe light so customers can add more coins if desired.

Reduces customer frustration and irritation with “running-out-of-time”. Timers are standard with meter decals (see below) explaining how they operate.

Accumulating, 24-Volt Bay Timers feature 1-31 coins to start and accumulate up to 255 coins. One second to Eight minutes per coin. Resettable coin counters are standard.

Adjustable for 1 to 63 coins to activate and from 1 second to 68 minutes per coin. 24-Volt AC hook-up. Accumulates to 163 coins or tokens. D

D

Compact and totally encapsulated, the Grace Timer can be mounted in the coin meter or in the pump room. Designed to work with either electronic or mechanical coin mechanisms. NOTE: 24 Volt input ONLY!

GS401

Part No.

Net Ea.

Last Alert Timer, coins or tokens ........ Warning Buzzer as option................... Strobe Light as option......................... Warning Horn as option....................... DULTMEIER SALES

Model 24400

$ 73.90

GRACE™ TIMERS

Part No. Net Ea.

GS GS401 GS GS20 GS GS29 DX RS1

D

110V or 24V Timer

30 seconds to 8 minute time selection per coin on 110 Volt. 1 second to 8 minute time selection per coin on 24 Volt.

Model GS20 is an optional warning buzzer for use with GinSan last alert timers. It features an output that allows your existing 24-volt running light to flash during the countdown period.

Model 24400 bay or vacuum timer. Can be used for 24 volt or 110 volt, no jumpers required • ETL rated to 30 amps • Accepts up to 16 coins or pulses to start • Accumulates up to 100 pulses to extend time cycle • Grace period option • Adaptable to pulse or coin counters • Built-in power surge protection.

Features: • Works with mechanical or electronic coin mechs • Excellent timing accuracy • Use for 24 or 120 VAC • Adapts to most coin switches & acceptors • Power Surge protected • Simple to understand, easyto-install • Convenient size • External cancel switch for easy testing • Time settings from 1 second to 18 hours. Applications • Self-service car wash in bay or vacuum

Solid State 110-Volt / 24 Volt

GS GS402 GS GS403

EPT321

ParaPlate Timers

Timers

GS403

Net Ea.

24 Volt or 110 Volt for Bay & Vacuum

Part No. Net Ea.

D

D

SG EPT321 Super Timer, 24/110 Volt.. $ 105.50 DX RS1 Warning Horn as option... 13.75

AT413

IX AT411E IX AT411EL IX AT411EX IX AT413 IX LC525

156

OMAHA, NE (800)

$ 171.00 123.00 CALL 13.75

228-9666

Part No.

Net Ea.

PK 2-PEM “Grace Timer” $ 92.25 •

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0123


Digital Timers

157

Big Time Countdown Displays

DIGITAL READOUT TIMERS DX300 Medium Display Timer. Features: Giant 4" numbers for easy viewing • 1 to 10 minutes per coin • Accumulates to 99 minutes • Count down style only, no scrolling message option • 12" x 8" stainless steel enclosure for easy mounting • Bonus time “grace” period option • Last minute warning feature (horn not included).

D

DX300

Large Digital Displays show customers the number of coins entered and the amount of time left in the wash cycle. Can be mounted anywhere in the bay for optimal customer viewing. Wires into your existing 24-volt bay timer. Features 72 letter scrolling welcome message that is pre programmed at time of order. Receives data from your existing bay timer. Sealed poly carbonate enclosure is standard for watertight protection. Horn not included. Model RC800 is a remote controller for future message change if desired. Models are shown with or without wall enclosure.

DX2002 Ultimate Timer

DX2002

Features: Large 3" x 12 dot matrix display D • Water-tight Stainless Steel Enclosure is 19" L x 8-1/2" W x 1-1/2" D • Time to start adjustable to 99 minutes • Time per coin is adjustable to 99 minutes • Operator programmable messages to greet and thank customers (up to 64 characters each) • Courtesy time option after unit times out • Remote control programming available but not included • “More Coins Needed” prompt if starting price has not been reached • Programmable for daily or weekly specials • Inventory manager keeps track of many timer functions • Built-in “Sun Switch light control.

DX200 Dryer Countdown Timer. For drive-thru dryers. Allows customers to know how much time is allowed and left during the drying cycle. 4" high digital display. Stainless steel case is 9-1/2" wide x 11" high x 2" deep. Time is adjustable from 0-99 seconds. Standard 110 volt. (24 volt also available).

BT900

IX BT900 Big Time Display, Poly Case................. $ 295.00 IX BT900E Big Time Display, Poly Case & Stainless Steel Enclosure..................... 338.00 IX RC800 Remote Message Controller................. 144.50 IX LC525 Horn...................................................... 36.00

Multi-Plex Controllers

D

Part No.

MX8 & MX10 Controllers are designed to replace bladder tanks and pressure switches on low pressure systems like brush, presoak and tire cleaner. Built in on/off delay eliminates pumps turning on and off when rotary switches are constantly changing positions. Can control up to 8 bays. LED readouts show bays in operation. Can be wired for 24 or 110 volt. 1 or 2 second delay as noted.

Net Ea.

Medium Display Timer Less Horn.............. $ 466.00 Large Display Timer Less Horn.................. 639.00 Dryer Countdown Timer............................. 446.00 Stainless Pedestal for DX200.................... 239.50 Warning Horn Only as add-on .................. 13.75 Control for remote programming................ 40.05

Large Digital Countdown Timers Large Digital Bay Timers from Dixmor. Can be mounted anywhere in the bay for best customer awareness. Display is 7-3/4” x 2-1/4”. Brightness changes automatically for different light conditions Programmable greeting message. Display shows dollar amount required to start. Message can be in English, Spanish or both. Last minute warning horn output. Standard with watertight plastic case. Also available in lockable stainless enclosure. Can be used for self-serve bays or in combo vacuum machines. • Time per coin is adjustable from 1 second to 10 minutes. • Coins to start is adjustable from 1 to 39. • Last minute alert adjustable from 0 to 59 seconds.

D

D

MX48 Controller is designed for use in triple foam systems to “pulse” chemicals and colors into the discharge lines. Adjustable for different pulse time periods.

MX8

Part No. Net Ea.

IX MX8 Multi-Plex Controller, 1-Second Delay....... $ 93.70 IX MX10 Multi-Plex Controller, 2-Second Delay....... 93.70 IX MX48 Triple Foam Controller................................ 289.00

Countdown Bay Timers GS31 is a visual countdown only. Wires to your existing timer.. Counts up time as coins or tokens are deposited and then counts down when timer has activated. LED numerals are 1" high and are bright red color. Moisture resistant, Lexan enclosure is sealed with a neoprene gasket. Note: Stainless steel wall Cover/Enclosure for mounting to wall and minute/second decal are optional. 24 Volt power. Two-year warranty.

D

LED9P

LED9S

* “M” Series Multi-Function Models allow for up to 6 different functions at different times and price settings. These units also allow for daily or weekly specials by using separate time clock control. These units are commonly used in combo vacuum machines. Part No.

Case

Net Ea.

DX LED9P Plastic $ 408.00 DX LED9S Stainless 473.00 DX LED9MP * Plastic 434.00 DX LED9MS * Stainless 500.00 DX RS1 Horn - Add On 13.75 * ”M” Series with multi-function option. DULTMEIER SALES

OMAHA, NE (800)

228-9666

D

Part No. Net Ea.

DX200

DX DX300 DX DX2002 DX DX200 DX DX200STAND DX RS1 DX RC1

RC800 Controller

D

D

GS31 with 40080

GS31B is same as GS31 but with an audible last minute alert buzzer that activates for 8 seconds with one minute remaining. Same optional items as above are applicable. 24 Volt power. Two-year Warranty.

D

GS 74328 Decal Part No.

Description

GS GS31 GS 74328 GS 40080 GS GS31B GS 74328 GS 40059

Visual Countdown Only........................ $ 398.50 Minute/Second Decal for enclosure..... 8.97 Stainless Wall Enclosure for GS31...... 46.05 Visual Countdown with buzzer............. 419.00 Minute/Second Decal for GS31B......... 8.97 Stainless Wall Enclosure for GS31B.... 47.05

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

Net Ea.

E0495


Coin Meter Digital & Countdown Timers

TimeMaster Countdown Timers

Little & Big Two-Timers IDX Two-Timers display coins deposited, time remaining and 72 letter welcoming message. The 2-Time feature also allows for different time/ price options at different times of the day. Bonus time for large coin startup and X-tra time feature that allows for additional coins to be deposited for 20 seconds at the end of the cycle are also standard features.

D

TimeMaster Countdown Timers feature a blue/green fluorescent display for maximum visibility. This color reduces the washed-out effect that sunlight has on red displays. Timers are housed in a water resistant, high impact plastic case. All units feature a wing nut to attach timer to existing meter lids. Timers will start on 1-20 coins and will accumulate up to 100 coins if desired. Time settings are from 1 second to 99 minutes per coin. D TM5J Timers can be used in 24-volt bay or vacuum applications. Besides the countdown feature, it also includes a “grace period”, last minute alert, bonus time and “change-over pause” feature for low pressure functions.

GT200

RC800 is a remote controller for future message changes if desired.

D

BT912 Big Two-Timer comes with stainless enclosure for mounting anywhere in the bay. Display letters are 2” high x 8” long. Overall size with enclosure is 12” x 7-1/2” x 2-1/2”. Warning horn is included. Part No. Net Ea.

Little Two-Timer................................... $ 295.50 Big Two-Timer in SS Enclosure.......... 500.00 Remote Controller............................... 144.50 24V Horn as option for GT200 ........... 36.00

Dimensions are 3' wide, 1-3/4" high, 3-3/4" deep. Input voltage is 24 volt, AC RS1 Horn Included

RC1T Remote Control

Part No.

Description

DX TM5J DX RS1 DX RC1T

Digital Timer With Horn.................................... $ 329.00 Warning Horn Only, as Replacement.............. 13.75 Control for remote programming & accounting. 95.70

Net Ea.

Tokens

DIGITAL READOUT TIMERS LED6 (Bracket Mount)

D

D

Keep your customers satisfied with Digital Readout Timers. Red L.E.D display shows continuous countdown of time from start to finish of cycle.

TM5J

Program messages can be set by switches on the units or by the RC1 remote control. All program memory is retained in case of power failure.

BT912

GT200 Little Two-Timer is designed to fit into existing meters. Fits common facelid openings with studs. Letters are 3/4” high. Overall size is 3.8” x 3.4” x 3.1”. Poly carbonate case is standard. Warning horn is not included but can be ordered separately.

IX GT200 IX BT912 IX RC800 IX LC525

158

These tokens are high security, 85/15 copper construction. Since this copper ratio is higher than the more common game arcade tokens, your coin mechanisms can be set to only accept the car wash ratio, which protects you from unwanted tokens. Stock size is .984”. Token use can help to eliminate theft and vandalism. Sold in bags of 1000 tokens. (Other sizes also available. Restricted tokens also available).

LED7 (Stud Mount)

All timers feature a 20 second “courtesy” period to add another coin after time has run out. Timers are adaptable to most any coin mechanism. Accumulating feature allows coins to be added at any time during the time cycle or “courtesy” period. All timers are 24-volt input and accumulate up to 99 minutes of total time. Standard with 1/4" Lexan coverplates for extra protection. (Warning horns are optional if required.)

D

D

Available Models:

D

LED6 Meter Timer is a retrofit for replacement of TM5 “Time Master” timers. Bracket mount. LED7 Meter Timer is 3-1/4" H x 3-1/4" W x 2-1/2" D and can be mounted into most existing coin meters. Messages can be in English or Spanish.

D

LED3 & LED5 in Coin Meter

Standard Features on all timers above: Programmable scrolling messages to greet and thank customers • 1-20 coins to start • 1 to 10 minutes per coin • Built-in resettable counter for inventory check • Built-in self-charging battery if power fails • Easily programmed with only 2 buttons.

Part No.

DX LED7 DX LED6 DX RS1 DX RC1

Part-No.

SERVICE & REPAIRS Did you know? We can service almost every brand of pump we sell in our catalog.

Net Ea.

Digital Timer, Less Horn ............................... $ 269.00 Digital Timer, (TM5 retrofit), less horn........... 295.50 Warning Horn Only as add-on ...................... 13.75 Control for remote programming................... 40.05 DULTMEIER SALES

OMAHA, NE (800)

228-9666

Net Ea.

HM T4340 Bag of 1,000 .984 Tokens......... $ 179.50

Call us at 1-800-228-9666 (Omaha, NE) for a quote! DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0121


159

Coin Mechanisms Sensortron Coin Mechanisms

Multi-Coin Acceptors

Coin / Token Acceptors

Electronic Coin Mechanisms are designed to protect you from jammers and cheaters. Solid-state design is able to electronically size, weigh, and accept any denomination of coin (foreign or domestic) or any desired token. Automatically rejects and immediately returns any improper coin, token or slug. Solid-state unit requires 24-volt power source. Returns undesired coins and tokens to customer. No moving parts or adjustments end jamming problems from bent, foreign, or wrong sized coins. Available with either 2" or 3" wide faceplates. Sensor tron units are single coin acceptance.

GS41-2 (Single Coin)

Model 77041 is a replacement insert only and does not include a faceplate. This unit will work with either 2" or 3" existing faceplates. (Fits Sensortron Mechanisms Only).

D

GS41-2

MA800 and X10 Coin Acceptors from IDX. Designed to accept up to 6 different coins or tokens. Pre-programmed to accept US quarters and dollar coins. Additional coins/tokens can be “learned” as required. Built in coin release opens chute to drop through bent or mutilated coins. Rated to 24 volt. 2” x 7-3/4” faceplate is standard. Coin/token acceptance range is .700” to 1.073” diameter and 0.87” to .130” thickness.

D D

MA800 mechanisms are designed to accept coins and standard, generic tokens. X10 mechanisms are designed for coins and high security X-Mark, coded tokens which are limited to your specific business.

MA800

Part No. Net Ea. IX MA800 Multi-Coin Mechanism....................... $ 162.50 IX X10 Multi-Coin X-Mark Token Acceptor.... 194.50

D

“SlugBuster”® Coin Mechanisms

All mechanisms shown are “Universal” and will work with most timers on the market today.

Slugbuster® Electronic Coin Mechanisms. Solid-state design enables these units to weigh, electronically size & accept a preferred coin or token. EZ Version allows for easier access to coin mechanism than old version mechanisms. 24 Volt.

77041 INSERT

Part No. Net Ea. GS GS41-2 Sensortron Mechanism, 2"............ $ 159.50 GS 77041 Sensortron Insert only for 2" or 3". 128.00 NP 902977 Plastic Coin Catch......................... 1.25 HM T4340 85/15 .984 Tokens, Bag of 1000... 179.50

P35EZ Slugbuster I - “Quarters Only”. Compares the coin in the holder with the coin to be accepted, (American or Canadian). P47 Slugbuster I (Old Version) “Quarters Only”. Units can be set to accept either US or Canadian quarters.

D

P55EZ Slugbuster II - “Quarter/Token”. Will accept either a quarter or token through the same coin slot.

P35 Long Drop

Electronic Coin Mechanisms

P83EZ Slugbuster III - “3-Coin” Mechanism. Allows for the acceptance of 3 different coins or tokens through same coin slot. Touch pad programming, no switches.

Replacement for “SECURECOIN” Electronic, Multi-Coin Mechanisms from the manufacturers of Secure Coin. Takes up to 5 different coins or denominations. Pre-programmed for US quarters and dollars and up to three other coins or tokens of your choice. Can also be easily set to accept Canadian coins or other foreign coins.

All mechanisms listed above are available in either a 2" or 2-1/2" wide faceplate. All models are also available in an “S” type “short-drop” style for compact coin-box lids. “Short-drop” SlugBusters will retrofit to many of the compact mechanisms that are presently in use having a faceplate dimension of approximately 2-3/4" wide x 5" long. Note: 2” wide mechanisms are 7-3/4” long.

D

P55S Short Drop

D

Note: Tokens smaller than .984" are not recommended; however, tokens up to 1" may be used in the “Regular” size models and up to 1-3/16" in the “short-drop” models. Brass tokens of an 85/15 construction are ideal for proper opera­tion.

EP5P-LD Long Drop

Standard Features: Touchpad programming • Auto-learning, no sample coins needed • Waterproof and tamper-proof • Built-in panel display • Solid-state electronic circuit • Long or short drop versions • Maintenance-free, only one moving part • 1-Year Warranty.

D

EP5P-SDS Short Drop

Part No.

Faceplate

Net Ea.

SG EP5P-LD 2" Long Drop, US Coins............. $ 206.50 SG EP5P-SDS 2-1/2" Short Drop, US Coins...... 217.00 SG CP900 2” Long Drop, Canadian Coins.. 232.50 DULTMEIER SALES

OMAHA, NE (800)

228-9666

Part-No. Mechanism Style: Width Net Ea. PK P35EZ Quarter ONLY - Slugbuster I, EZ Version.................. 2" $ 133.00 PK P35SEZ Quarter ONLY - Slugbuster I, Short EZ Version ........ 2-1/2" 133.00 PK P37 * Slugbuster for ACW Units........................................ - 190.00 PK P47 Quarter ONLY - Slugbuster I...................................... 2" 137.00 PK P55EZ Quarter/Token - Slugbuster II, EZ Version................. 2" 155.00 PK P55SEZ Quarter/Token - Slugbuster II, Short EZ Version........ 2-1/2" 155.00 PK P355 Looney/Tooney - Slugbuster II .................................. 2" 156.50 PK P83EZ 3-Coin Slugbuster...................................................... 2" 199.50 PK P83SEZ 3-Coin Slugbuster, Short Drop................................... 2-1/2" 194.00 NP 902977 Plastic Coin Catch .................................................... - 1.25 HM T4340 85/15 .984 Tokens, Bag of 1000............................... 179.50 * Insert Only, No Faceplate. DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0124


Coin Mechanisms ACCEPTORS • Industry standard faceplate for easy retrofitting.

Electric Coin Mechanisms Now a Coin Mechanism with the benefits of a manual Reject Button along with Coin Logic.

D

Multi-Coin Electronic Mechanisms with jam-proof design that you have come to expect. Designed for (quarter & dollar coins), (quarters & .984 tokens) or (quarters, dollars and .984 tokens if token is valued at $.25 or $1.00). One slot accepts all coins. 2 or 3 coins can be accepted, but only 2 valuations can be set for acceptance. Rated for 24-volt use. Standard with 7-3/4" x 2" stainless steel faceplate. (Mechanisms for other size tokens also available on request).

• 8 Coins per second acceptance rate. • Accepts up to 9 different coins/tokens. • Installing a Microcoin is like hiring a full time attendant. • 2 Year Warranty

QL

(Insert Only)

Electronic, multi-coin, coin mechanisms from Microcoin. Can be programmed to accept up to 9 different coins or tokens. Will work with U.S. or foreign coins if desired. High coin acceptance rate, (up to 8 coins per second) means less jam problems. Standard with 2" x 7-3/4" industry standard faceplate. Rated for 24-volt timer pulse and input. Accepts coins from 16mm to 34mm diameter and 1.0mm to 3.4mm thickness. Units can be easily opened up for cleaning.

D

160

QLC

Accepts Coins and/or Tokens. Manual coin processing system separates coins without moving D parts. Reduces jamming. 24-Volt Optic System replaces coin switches. Electronic components are coated for water resistance. Adjustable for pulses per coin and coins to start. 2” Faceplates are standard, 3” also available. Z3 Models will accept up to 2 coins or tokens at one value. (Example: US quarter = $.25 or US quarter and token = .$25. Z32 Models will accept up to 4 coins or tokens at up to 2 values. (Example: US quarter = $.25 and US dollar = $1.00 or US quarter = $.25 and US dollar and token = $1.00).

Many Other Coin and Token Options are Available - Call for Pricing. Part No. IV Z3-950 IV Z3-9QT IV Z32-950 IV Z32-QT IV Z32-1TT IV Z32-C12

Coin Mechanism Coin Mechanism Coin Mechanism Coin Mechanism Coin Mechanism Coin Mechanism

Accepts/Value Net Ea. US Quarter=1 Value.................................. $ 98.85 US Quarter & .984 Token=1Value............ 102.50 US Quarter & $1 Coin=2 Values............... 158.00 US Quarter & .984 Token=2 Values.......... 164.00 US Quarter, $1 Coin, 984 Token=2Values 164.00 Canadian $1 & $2 Coins=2Values............ 166.00

(Complete Mechanism)

Coin Acceptors

Part-No.

DX QLC DX QL

Now a coin acceptor with no moving parts.

Net Ea.

MicroCoin Acceptor COMPLETE................ $ 210.00 MicroCoin Acceptor, INSERT ONLY — NO BRACKET............................................ 190.00

Mechanical Coin Mechanisms will accept U.S. Quarters, Tokens, Canadian quarters and Loonies or other foreign coins. No troublesome rockers, cradles or electronics. Perfect for coin meters, vacuums and vending machines. Unique, patented, plastic molded design virtually eliminates jamming and features the highest rate of acceptance ever. Especially effective where dirt, dust or weather can cause problems in rocker and cradle style mechanisms. Insert only acceptors will fit most existing 2" face plates.

Mechanical Coin Mechanisms Coin Mechanisms for coin vaults, vacuums or coin meters. Some of the more popular mechanical acceptors used in the car wash market. These mechanisms feature a chrome faceplate and a coin return for wrong coins. Metal internal mechanisms are standard. Faceplate is 2" wide x 7-3/4" long. Includes coin switch. All mechanisms accept U.S. quarters only.

D D

D

D

90001 Insert Only 9000 Series Mechanical with Coin Switch

8145 130-25

MECHANICAL COIN MECHANISMS Part Number IV 90001 IV 90001BK IV 90009 IV 90009BK IV 90007 IV 90007BK IV 900104 IV 900104BK IV 75961 IV 75968 HM T4340

902977 8146

Part-No.

AA 8145 AA 130-25 AA 8146 NP 902977

Net Ea.

Complete Coin Mechanism with 130-25...... $ 48.60 Insert Only, No Faceplate .......................... 24.50 Coin Switch for 8145 Coin Mechanism....... 8.90 Plastic Coin Stop ....................................... 1.25 DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

Accepts Acceptor Insert only US Quarters only Acceptor with Bracket US Quarters only................ Acceptor Insert only US Quarters & .984 Tokens. Acceptor with Bracket US Quarters & .984 Tokens. Acceptor Insert only US Quarters & .900 Tokens. Acceptor with Bracket US Quarters & .900 Tokens. Insert only Canadian Loony Only......... Acceptor with Bracket Canadian Loony Only......... Coin Switch as replacement, Otehall Brand............... Coin Switch as replacement, Cherry Brand .............. 85/15 .984 tokens, Bag of 1000.................................

553-6975

www.dultmeier.com

Net Ea. $ 16.30 38.60 20.00 47.05 20.00 47.70 21.55 53.05 6.96 5.66 179.50 E0125


Coin Meter Accessories

161

ROTARY SWITCHES

Model 10R3

24-Volt Running Lights

#8GR Green

For Coin Meters or Electrical Panels — 24 Volt —

D

D

8, 10 & 12 Position 2 or 3 Stack

#8 Red

15-Amp 600-Volt D

Part No.

Net Ea.

JS 8 RED Running Light JS 8GR GREEN Running Light

$ 3.60 3.60

2M Knob

Standard in the “make-before-break” style for added life of your electrical components. Available in either (2) or (3) “Stack” style. Rated at 15 Amp-600 volt continuous. Can be mounted single-hole (Coin Meters), panel or bushing mount. Note: 12 Position switches require support studs on meter lids. Part No. JS 10R2 JS 10R3 JS 10R5 JS 10R7 JS 10R8 JS 2M JS 2M5 JS 2M2

Electrical Impulse Counters Non-Resettable

D

Model 10R8

2M2 Knob

Non-Resettable Electric Counters for Industrial or Commercial Applications. Ideal for coin meters or vacuums to verify the number of coins or tokens that have gone through your mechanisms. 6-digit display. Counts to 999,999 and then repeats. Accurate up to 600 counts per minute. Standard with mounting bracket and 10" lead wires. 24 or 120 volt AC or 12 Volt DC.

D

Net Ea. 2-Stack, 8 Position Rotary Switch............. $ 22.80 3-Stack, 8 Position Rotary Switch............ 36.95 2-Stack, 10 Position Rotary Switch .......... 53.20 3-Stack, 10 Position Rotary Switch........... 63.10 2-Stack, 12 Position Rotary Switch .......... 131.00 Replacement Knob, PLASTIC, Black........ 1.70 Replacement Knob, Yellow........................ 5.16 Black Knob for 10R8 Switch...................... 7.26

Part No.

Net Ea.

NP 423140 NP 421167 NP 420092

24 Volt AC Counter 120 Volt AC Counter 12 Volt DC Counter

Wall Safes

190P Lid

For Added Security & Protection

D

• Square or Round Design.

COIN SWITCHES

8146

• Available in 10" - 18" Lengths. Round Style Wall Safe

$ 9.77 9.77 8.97

Replacement trip switches for bay and vacuum coin mechanisms. Standard retrofit or replacement item. Available in three different models. Arm length and electrical spade location vary with regards to the type of coin mechanism that is being used.

D

• Plated or Stainless Steel Heads.

D

Plastic Coin Tray

75968 D

75961

Round Style Wall Safe (Front View)

D

D

ML20 Plug Lock (must be ordered separately)

S9SQ Square Style Wall Safe

These Stainless Steel Wall Safes are available in round or square design. Round models are available in lengths from 10" ($700 capacity), 14" ($1200 capacity) or 18" ($1600 capacity). Square design is 12" deep x 8" wide x 8" high, capacity is $750. Round model safes are available with either Plated or Stainless Steel heads. All round safes are 8" in diameter and have two nipples for coin openings. Plastic coin tray is included. Note: Lock is not included on round safes. Capacity Part No. Length Head Quarters

Net Ea.

DU S10P 10" Round Plated $700 DU S10S 10" Round Stainless $700 DU S14P 14" Round Plated $1200 DU S14S 14" Round Stainless $1200 DU S18P 18" Round Plated $1600 DU S18S 18" Round Stainless $1600 DU S8SQ *12" x 8" Square Stainless $750 DU S9SQ *12" x 9" Square Stainless $1000 DU 190P Plated Lid Only, replacement............... DU ML20 Plug Lock, MEDECO............................ * Square Models include Locks.

$ 397.00 467.00 409.00 475.00 409.00 479.00 367.50 350.50 236.50 22.95

OMAHA, NE (800)

228-9666

DULTMEIER SALES

Part-No. AA 8146 IV 75968 IV 75961

For Mechanism Brand Net Ea. “Coin Mech” or “Coin Co” Acceptors. $ 8.90 Imonex, 3-Prong............................... 5.66 Imonex, 2-Prong............................... 6.96

Heat Tapes Heat Tapes for moisture control and freeze prevention. Ideal for mounting in many types of coin meters. Adhesive backing on 1M, 3M & 4M. Tapes are 3" x 1" with 8" lead wires.

24-Volt

D

1M

Part-No.

JS 1M JS 3M

Watts

24-Volt Heat Tape 24-Volt Heat Tape

9 25

Net Ea.

$ 15.75 15.95

Less 5% on 10 or More -Not Assorted

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0126


Validators & Bill Acceptors MARS Bill Acceptors

162

Vantage Bill Acceptors Specially Designed for the Car Wash Industry! AE2412U3E

Validator Bill Acceptors from MARS for a wide variety of changer needs. Four direction bill acceptance. Re-programmable flash memory. Easy access to the bill path even while mounted. Diagnostic LED. 300, 500 and 700 bill stackers. Available in 24 volt for bay meters or 110 volt for bill changers. (Other models also available).

From CoinCo: Vantage Bill Acceptors for bay meters in wet environments. Also an ideal choice for bill changers and auto cashiers in outside areas. Industry Leading Water Protection: Coated circuit board (24v Only) • Molded water seals • Patented water removal cycling design • Water diversion channels • Molded drain ports.

D

Industry Leading Security: Optical stringing protection • Patented cash box lock out mode • Patented anti-fishing barrier • High security metal entry bezel. Accepts $1 through $20 bills in four orientations. Cash box holds up to 400 bills. Models shown accept US bills, (Canadian models also available). Illuminated bill entry and attention grabbing lighting. Automated self diagnostics. Can be programmed for coupon or token note acceptance if desired. Available in 24 volt or 110 volt models and with two different bezel mask options.

Decals Included

Part No.

Voltage

Changes

Stacker

D

Large Mask

Net Ea.

AV AE2412U3E 24 Volt $1 & $5 300 Bills $ 331.50 AV AE2612U3E 24 Volt $1/$5/$10/$20 300 Bills 374.50 AV AE2602U5M 24 Volt $1/$5/$10/$20 500 Bills 367.00 AV AE2602U7 24 Volt $1/$5/$10/$20 700 Bills 367.00 AV AE2601U5E 110 Volt $1/$5/$10/$20 500 Bills 367.00 AV AE2631D7 110 Volt $1/$5/$10/$20 700 Bills 349.00

Pyramid Bill Validators

VL61R

VL62B

Bill Validators from Pyramid. Available in 110 volt for bill changers or 24 volt for self-serve bays. Interchangeable with CoinCo or Mars validators. D

Both Series have the following standard features: Optical anti-stringing • Lighted arrows at bill entry • LED on-board diagnostics • 500 Note bill stacker • Wiring harness • Automatic self-calibration.

D

Small Mask

D

Part No.

ACCEPTORS Net Ea.

AV VL62B AV VL62R AV VL62S AV VL61B AV VL61R

24 Volt, Bills Acceptor, Large Mask, 400 Bills.............. $ 333.00 24 Volt, Bills Acceptor, Small Mask, 400 Bills.............. 333.00 24 Volt, Bills Acceptor, Small Mask, 400 Bills.............. 333.00 110 Volt, Bills Acceptor, Large Mask, 400 Bills............ 308.50 110 Volt, Bills Acceptor, Small Mask, 400 Bills............ 332.00

Bill Validators Bill Pro Series

5401-U59

Small Mask

Bill Validators for Vending Machines, Bay Meters, Change Machines, etc. Accepts all new and old currency and is programmable for future currency changes. Can be set to accept, $1, $2, $5, $10 and $20 bills if desired. Design subjects bills to optical and magnetic tests for more security.

AQ9U53

Aqua Models additional features include: No sensors in the water path • A water drainage rear port • Corrosion-resistant shafts • A bill path that is designed for moist bills • These models can also be easily programmed for coupons if desired.

D

Standard Features: Impact resistant front mask • Anti-jam software • Illuminated bill inlet • Components are resistant to salting, corrosion and rust • Snap-in design means easy access & cleaning.

Large Mask

Part No.

Series

AV 5401-U59 AV 5401-U52 AV 5400-U59 AV 5400-U52 AV AQ1U53 AV AQ9U53

Apex 24 Volt Apex 110 Volt Apex 24 Volt Apex 110 Volt Aqua 24 Volt Aqua 24 Volt

Voltage

DULTMEIER SALES

Mask

Net Ea.

Small Small Large Large Small Large

$ 229.50 219.50 229.50 229.50 249.50 249.50

OMAHA, NE (800)

228-9666

D

Part No.

VALIDATORS Net Ea.

AV BP4SX

110 Volt with Harness, Short Mask, 500 Bill..............

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

$ 297.00 E0715


Bill & Credit Card Changers

163

Standard MC Bill Changers

Credit Card to Token Machines An easy way to have credit card acceptance at your facility. Accepts MasterCard, Visa, American Express and Discover Cards. Two models are available: Credit Card to Token or Credit Card and Bills to Tokens. Rear load design on both models. Standard Features Include: Weatherproof magnetic stripe card reader • Dial up POS Terminal Device • LCD display for instructions and customer feedback • Stainless steel faceplate with powder-coated steel cabinet • Tough Lexan graphics • ETL Certified in accordance with UL and CSA standards • Out of service indicator light • Multiple credit card processors available • (2) Hoppers with 10,400 token capacity, (US quarter size) • Dimensions are 32” H x 18” W x 13” D. (Add 2” on all sides for faceplate dimensions)

MC Series Bill Changers from Standard Change-Makers. Designed with economy and simplicity in mind. Changes $1/$5/$10/$20 bills to quarters. Cabinet is 12-gauge steel with Stainless Steel faceplate. COINCOValidators with 500 bill stackers are standard. Dual T-Handle plug locks for added security. Bills to coins only. "Smart Hopper" Technology has controller built onto coin hopper. (Mars Validators also available on all models). Model MC300RL: Rear Load Model features validator, one hopper that holds up to 3200 quarters. *Dimensions are 9" W x 32" H x 13" D. Model MC400RL: Rear Load Model features two hoppers that hold up to 3200 quarters each, (6400 quarter capacity). *Dimensions are 13-3/4" W x 28" H x 13" D. D D

MC400RL

MC300RL

Model MC500RLDA: Rear Load Model is two separate machines in one cabinet. Each machine has 3200 quarter capacity (6400 total capacity). *Dimensions are 18" W x 32" H x 13" D.

D D

MC525RL-CC

MC535RL-CC

Part No.

Changes

Weight Net Ea.

SZ MC525RL-CC SZ MC535RL-CC

Credit Cards ONLY............. Credit Cards & Bills............

110 lbs. $ 4450.00 110 lbs. 4550.00

Model MC520RLDA: Rear Load Model is one machine with 2 validators, two hoppers and one discharge cup. If one hopper is empty, the other takes over to make change. Dual backup in one machine. 6400 quarter total capacity. *Dimensions are 18" W x 32" H x 13" D.

Bill Exchanger Machines Rear Load Bill Exchanger Units. Two different changer models: Bills to Bills or Bills to Bill & Coins. Single bill acceptor has 500 bill capacity. Bill dispensers have capacity of 1,000 new or 750 used bills. Stainless steel faceplate with powder-coated steel cabinet. Two Year Warranty and ETL Certified in accordance with UL and CSA standards. Standard with MARS bill acceptors and FUJITSU Bill Dispensers. Model BX1010RL is a Bill to Bill unit. Changes $10 or $20 bills to either $1 or $5 notes, (not both). Dimensions are 28” H x 17” W x 18” D. Add 2” to all sides for faceplate dimensions. Model BCX1010RL is designed to change $1/$5/$10/$20 notes to bills and quarters. Coin hoppers have 6,200 quarter capacity. Dimensions are 36” H x 18” W x 18” D. Add 2” to all sides for faceplate dimensions.

D D

MC500RLDA 2 Machines in 1 Cabinet

Part No.

MC520RLDA 2 Validators in 1 Cabinet

Description

Weight Net Ea.

SZ MC300RL Single Hopper.......................... SZ MC400RL Double Hopper........................ SZ MC500RLDA Dual Machines......................... SZ MC520RLDA Dual Hopper & Validator.......... SZ MC300RLM Single Hopper, Mars................ SZ MC400RLM Double Hopper, Mars.............. Note: Add 4” to Height & Width for Faceplate.

110 lbs. $ 1749.00 125 lbs. 2255.00 135 lbs. 3061.00 133 lbs. 3025.00 133 lbs. 1849.00 133 lbs. 2349.00

Two Year Limited Warranty!! D

All Standard Change-Makers machines are covered by the Best Warranty in the Industry!! Standard Change-Makers Warranty covers all defects in Material and Craftsmanship for two (2) years on Parts, and one (1) year on Labor — and covers the repair or replacement of the defective item.

D

BCX1010RL

BX1010RL

Part No.

Changes

Weight Net Ea.

SZ BX1010RL SZ BCX1010RL

Bills to Bills......................... Bills to Bills & Coins............

140 lbs. $ 3798.00 215 lbs. 4498.00

DULTMEIER SALES

OMAHA, NE (800)

228-9666

Original Manufacturer Warranties may apply to certain components, and are not applicable to this Warranty. DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0111


Bill Changers • Cleaning Cards

164

SINGLE CHANGERS

DUAL CHANGERS

Changes $1.00, $5.00, $10.00 & $20.00 Bills

MODEL DRS is two changers in one cabinet. Perfect choice for those high volume washes. Gives you the security of having a second changer available for your customers. Capacity is $2400. Changes $1, $5, $10, $20 bills. Bill Stacker, heater and weathershield are included. 11-gauge stainless faceplate and cabinet. Minimum wall opening is 34-3/4" H x 18-3/16" W x 14-7/16" D. Weight is 230 lbs.

RNS Bulk Load Changers feature $1200 capacity, single bill stacker, heater and weathershield. Stainless steel faceplate. ER60 Bulk Load Changer features $600 capacity, single bill stacker, heater and weathershield. Stainless faceplate with carbon steel cabinet. Validator options shown below. D

D

D

D

Bulk Load Hopper Direct Payout Reliability

Model DRS

Model ER60

Model RNS

Hopper-Load changers have no tubes, vibrators, belts, slides, chains, solenoids or relays to cause problems. Even bent coins can’t interfere with delivery. Part No.

VALIDATOR

CAPACITY

WT.

Tokens size .984 or .901 can be dispensed without modification. Other sizes may require slight conversions.

Net Ea.

HA ER60 ** HVX $ 600 135 lbs. $ 2655.00 HA ER60C Coinco $ 600 135 lbs. 2480.00 HA ER60M Mars $ 600 135 lbs. 2655.00 HA RNS ** HVX $ 1200 150 lbs. 3275.00 HA RNS-C Coinco $ 1200 150 lbs. 3097.00 HA RNS-M Mars $ 1200 150 lbs. 3275.00 HA DRS ** HVX $ 2400 230 lbs. 5541.00 HA DRS-C Coinco $ 2400 230 lbs. 5209.00 HA DRS-M Mars $ 2400 230 lbs. 5541.00 HA XE ** Replacement Validator, $1, $5, $10, $20 Bills .. 699.00 PK P37 Slugbuster, Coin Mech......................................... 190.00 HA 63-5002 (1) Pair Medeco Plug Locks with Barrels............. 74.30

Dimensions, RNS: Minimum wall opening is 34-1/2" H, 9-7/16" W, and 13-1/8" D. Face­plate: 38-1/2" H and 12" W. Dimensions, ER60: Minimum wall opening is 20-3/4" H, 15" W, and 13" D. Faceplate: 24-3/4" H and 18" W.

Bill Validators All changers are now available with 4 different bill validators to choose from: Hamilton, Coinco or Mars for U.S. currency or Ardac for foreign currency. Order to meet your specific applications.

F.O.B. FACTORY. ** For replacement of HVX Machines. D

Part No.

Model XE as Replacement

Net Ea.

HA XE $ 699.00

Cleaning Cards Cleaning Cards for Credit Card Readers and Currency Validators. An easy and cost effective way to keep card readers and bill validators clean and operating efficiently. Removes dirt, oxides and contaminants from all types of concealed magnetic heads as well as optic and photo sensors. Alcohol or non alcohol as listed.

D

27CH

D

75VCW D

Per Box Part No. CARD TYPE Net Ea.

78VC

DULTMEIER SALES

AV 27CH AV 25CHW AV 78VC AV 75VCW OMAHA, NE (800)

228-9666

Card Reader Cleaning Cards, Flat Strip, Box of 50, Alcohol Base............. Card Reader Cleaning Cards, Waffle Style, Box of 40, Alcohol Base........ Bill Acceptor Cleaning Cards, Flat Strip, Box of 25, No Alcohol............... Bill Acceptor Cleaning Cards, Waffle Style, Box of 15, No Alcohol...........

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

$ 27.95 24.95 17.95 20.85 E0110


American Bill Changers

165

Rear Load Bill Changers

Front Load Changers

Rear Load Bill Changers from American Changers. Inexpensive options to many of the changers used in the industry today. The basic philosophy of this brand of changers is to use common components such as validators and hoppers that can be repaired or replaced from a wide variety of sources. No delays or down time. All machines are standard with “Pyramid” Validators, but “Coinco” and “Mars” are also available. Hoppers are designed so that quarters, dollars and tokens can be dispensed without any adjustments.

Same quality components as shown in the Rear Load Models but in a Front Load Design. Both Changers shown will accept, $1, $2, $5, $10, $20 bills in both the new and old bill designs.

Model AC1002 Model AC1002 Steel Cabinet: Features a single validator, single hopper and (2) high security locks. Capacity is 2800 quarters or tokens and 2200 dollar coins. Dimensions are 10-1/2" wide x 26" high x 13" deep.

All models shown below are rear load design. All changers will accept $1, $2, $5, $10, $20 in both new and old bill designs. Bill stackers and a token bonus payout is also standard. Printers are optional. Face plates are 8-gauge Stainless construction. Cabinets are 14-gauge steel construction.

Model AC8002

D

Model AC8002: Has the same specifications as AC1002 but with all stainless steel construction.

Model AC1005 Model AC1005 Stainless Faceplate with Steel Cabinet: Features a single validator with a single hopper. 2800 quarter or token and 2200 dollar coin capacity. Wall opening requirement is 8-1/2" wide x 26" high x 13" deep. Shipping weight is 74 lbs.

Model AC8005

Model AC2002

Model AC8005 Stainless Faceplate and Cabinet: Same specifications as AC1005 except wall opening is 10-1/2” wide x 26” high x 13-1/4” deep.

Model AC2002: Features dual hoppers, dual Validators and (2) high security locks. Capacity is 5600 quarters or tokens and 4400 dollar coins. Dimensions are 15-1/2" wide x 26" high x 13-1/2" deep 14 gauge steel. Shipping weight is 98 lbs.

D

AC1005

Part No.

Model AC2005 Model AC2005 features one validator with dual hoppers. 5600 quarter or token and 4400 dollar coin capacity. Wall opening requirement is 13-1/2" wide x 26" high x 13" deep. Shipping weight is 115 lbs.

D

AC2002 Dual Validator

AC1002 Single Validator

Coin Capacity

Hoppers

AV AC1002 2800 quarters or tokens AV AC8002 2800 quarters or tokens AV AC2002 5600 quarters or tokens * All Stainless Construction.

Wt

Net Ea.

75 lbs. $ 1665.00 84 lbs. 2125.00 98 lbs. 2687.00

1 * 1 2

Credit Card Token Machine

AC2005

Exclusively designed and developed to increase sales in the Coin-Operated Wash Industry. Now your customers can use their credit cards to purchase tokens for use in your car wash.

Model AC2221 Model AC2221 is two separate AC1005 changers assembled to one faceplate. Two separate hoppers and validators give you two machines. 5600 quarter or token and 4400 dollar coin capacity. Wall opening requirement is 17" wide x 26" high x 13" deep. Shipping weight is 143 lbs. D

AC2221

Model AC2225 Model AC2225 Stainless Faceplate with Steel Cabinet: A dual validator, dual hopper, high capacity machine. 12,000 quarter or token 9500 dollar coin capacity. Wall opening requirement is 19" wide x 29" high x 14" deep. Shipping weight is 182 lbs. D

Model AC8225 D

D

AC2007

Model AC8225 All Stainless Changer: Has the same specifications as AC2225 except wall openings are 25” wide x 26-1/2” high x 16-1/2” deep.

Part No.

AV AC2007

Standard Features: Simple instructions guide customers through the purchase process • Four selections on LCD screen to choose from • Receipt and audit printer • Can be operated on dedicated or non-dedicated phone line • 2 Hoppers • 3200 token capacity • Unlimited bonus payouts to meet your specific market • Wall opening requirements are 13-1/2" wide x 26" high x 13" deep • Shipping weight is 115 lbs.

Token Capacity

Hoppers

Wt.

3200

2

115 lbs.

Net Ea.

$ 4398.00

AC2225 Part No.

Coin Capacity

Hoppers

AV AC1005 2800 quarters or tokens Single AV AC8005 2800 quarters or tokens * Single AV AC2005 5600 quarters or tokens Dual AV AC2221 5600 quarters or tokens Dual AV AC2225 12,000 quarters or tokens Dual AV AC8225 12,000 quarters or tokens * Dual * All Stainless Construction. DULTMEIER SALES

Wt.

Net Ea.

78 lbs. $ 1615.00 114 lbs. 2625.00 115 lbs. 2111.00 141 lbs. 2859.00 162 lbs. 2859.00 170 lbs. 3860.00

OMAHA, NE (800)

228-9666

Order From Our Entire Inventory On-Line!

Dultmeier.com

Current Pricing • Web Specials • Closeout Items • DAVENPORT, IA (800)

553-6975

• Current Flyers • Order Status • Parts Schematics •

www.dultmeier.com

E0112


Bill Changers

166

RearLoad Bill Changers

Bill Breakers

Model BC1400 is standard with dual hoppers, dual bill stackers and will accept $1, $2, $5, $10, $20 bills.

Bill Breakers allow customers to break large bills like $10 and $20 into smaller bills and/or coins. Many customers don’t like to change large bills into quarters only. Bill Breaker machines are the answer. These machines can also double as a bill to coin changer if that option is ordered. Keep some of those dollars at your wash with a Bill Breaker from Rowe. Available in Front or Rear Load models. Options allow for large bills changed into 1 or 2 smaller bills and also coins or tokens if desired.

Model BC200 is standard with a single hopper, a single bill stacker and accepts $1, $2, $5 and $10 bills. Both units feature a heater and the most reliable bill stacker in the industry. Central computer control handles important functions including bill validation, change dispensing and changer function monitoring The rear-load feature of these changers allows for flush wall mounting. Stainless steel front plate helps to protect against vandalism. Unique design allows machine to shutdown if one malfunction occurs. Self diagnostic capability isolates problems and faults are shown on a digital display. A belt conveyor on the bill transport provides self-clearing of foreign objects. All components are protected by circuit breakers, no fuses. Unitized, welded cabinet is 13 gauge on the BC1400 and 12 gauge on the BC200. Standard with 3 point lock bars and easy-toclean Teflon-lined hoppers.

D

D

500RLC1-2

BC1400

Standard Features: User Feedback Display • Printed Reconciliation Report • Fast Feed Shutdown • MARS Bill Acceptors and FUJITSU Bill Dispensers • 500 Bill Stacker Capacity • Bill to Bill or Bill to Bill & Coin Models • Front or Rear Load Cabinets • All Machines Will Accept $1, $5, $10, or $20 Bills • 120 Volt, 60 Hz. NOTE: Rear load models have stainless steel faceplates. All models have black, powder coated cabinets.

SPECIFICATIONS Model BC1400: Power: 120 VAC, 60Hz, 300 Watts. Weight: 210 lbs. Dual Hopper capacity: 3400 quarters per hopper. Cabinet Dimensions: 12-1/16" wide, 38-5/8" high, 18-1/4'’ deep. Faceplate: 43" H, 18" W. Dual Stacker capacity is 2000 bills.

DIMENSIONS

D

REAR LOAD MODELS:

500RL-2. Cabinet: Height: 16-1/2”, Width: 18”, Depth: 17-1/4”. Faceplate: Height: 21-3/4”, Width: 23-3/4”.

BC2800

500RLC1-2. Cabinet: Height: 32”, Width: 18”, Depth: 17-1/4”. Faceplate: Height: 37-1/4”, Width: 23-3/4”.

SPECIFICATIONS Model BC200: Power: 120 VAC, 60Hz, 250 Watts. Weight: 175 lbs. Single Hopper capacity: 3400 quarters. Cabinet Dimensions: 14-3/4” wide, 23-3/4” high, 18-1/4” deep. Faceplate: 27-1/2” H, 18” W. Single Stacker capacity is 1000 bills.

FRONT LOAD MODEL:

500C1-2. Height: 32”, Width: 18”, Depth: 17-1/4”.

$5/$10/$20 In Part No. Cabinet Changes Out

RX 500RL-2 RX 500RLC1-2 RX 500C1-2

Rear Load 2 Bill Denominations Out Rear Load 2 Bills & 1 Coin Out Front Load 2 Bills & 1 Coin Out

Wt.

Net Ea.

92 lbs. $ 5298.00 125 lbs. 5995.00 120 lbs. 5798.00

OMAHA, NE (800)

228-9666

BC200

BC2800 Bill Changer has two separate changers in one cabinet. Features: Four hoppers • (2) Thermostatically controlled heater • Dual doors for twice the security • Stainless Steel front plate • Dual independent electrical systems • Machine controlled by plug-in programmable electronic chip • 16 Character selfdiagnostic display. Dimensions: 38-5/8" H x 24-1/8" W x 18-1/4" D. Faceplate is 30" wide x 43" high. Stacker capacity is 1000 bills per bill box (dual bill boxes each unit).

Call Us For All Your Car Wash & Truck Wash Needs! DULTMEIER SALES

D

D

BC2800

Part No. ROWE CHANGERS Wt. Net Ea. RX BC200 * Rear Load Changer 175 lbs. $ 3398.00 RX BC1400 * Rear Load Changer 210 lbs. 3598.00 RX BC2800 * Dual Changer 420 lbs. 7298.00 RX 65068501 BA50 Validator.......................... 570.00 AV 78VC Cleaning Cards, Flat Strip, 25/Box..... 17.95 AV 79VNA Cleaning Cards, Non Alcohol, 25/Box 15.95 * Not Subject to Discounts. — F.O.B. Factory —

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0767


Coin & Currency Counters

167

COIN COUNTING SCALE Coin Counting Scale makes counting easy and accurate. With a resolution of 1/500,000 - the DMC782 counts every coin, every time. Large 12” x 9” platter can accommodate rolls, pouches or cash drawers and bins. Backlit LCD display shows weight, denomination and amount/quantity.

D

CURRENCY COUNTERS • High Throughput

• LCD Display

• Advanced Size Detection

• Portable

• Superior Accuracy

• User Friendly

• Flexible Batching

Can batch count from 1 - 999 bills Can be preset to count 10, 20, 25, 50 or 100 notes at a time.

Power supply is 115 Volt but rechargeable 300 hour battery is also available if required for mobile work stations. Can be programmed for up to 18 memory stations for various coins and/or tokens. Real time information can also be used with a PC through a standard RS-232 output. Overall dimensions are 11” x 13-3/4” x 4-1/2”. Capacity is 60 lbs. Part No.

DF DMC782

Wt.

COIN Scale, 115 Volt

5 lbs.

Net Ea.

$ 559.00

SC303 COIN COUNTER

The SC1500 Currency Counter features high speed throughput from 500 to 1500 notes per minute.

Count coins and tokens easily and quickly with a Model SC303 Scan Coin Counter. Standard Features Include: LED display • 120 volt operation • Counts up to 2700 coins per minute • Easily adjusted to virtually any coin or token • Separates mixed denominations • Auto reverse for jam clearing and D shut-off when no more coins are detected • Pre-programmed stops • Three memory levels with a subtotal, grand total and bag count • Microprocessor controlled for storing all vital data, no battery backup required • Coin Diameter range from .55" - 1.33" • Coin Thickness range from .04" - .13" • Dimensions: 9" W x 19" D x 9" H. Part No. Wt.

CO SC303

D

Model SC1500

Size detection for the height of the notes is standard. Compact and functional design combined with a weight of 12 lbs. makes it easy to move the machine between different locations. Standard functions include continuous counting as well as batching of any quantity between 1-999. Automatic restart after each completed batch gives high throughput. Input capacity is 500 notes. Voltage is 110V. Part No. Wt.

CO SC1500

Net Ea.

CURRENCY Counter.............. 12 lbs. $ 596.00

AMERICAN CHANGER CORP.

CURRENCY COUNTER

Net Ea.

Designed with Counterfeit Detection

COIN Counter......................... 17 lbs. $ 1027.00

Specifically designed to accurately count bank notes in bulk at up to 1000 notes per minute. Reduces labor and losses that result from human counting. Delivers high speed, accurate counting with the option of batching bills in groups of 10, 20, 25, 50 or 100 notes.

FEATURES: LED readout of bill count and batch count • Rated for 110 volts • Designed with counterfeit detection • Dimensions are 10-1/4" W. x 12-3/4" D. x 10-1/2" H.

Call Us For All Your Car Wash & Truck Wash Needs! SERVICE & REPAIRS Did you know? We can service almost every brand of pump we sell in our catalog.

D

AMERICAN CHANGER CORP.

Call us at 1-800-228-9666 (Omaha, NE) for a quote!

Part No. Wt.

AV BC101 DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

Net Ea.

CURRENCY Counter............ 17 lbs. $ 299.00

553-6975

www.dultmeier.com

E0113


Solenoid Valves

168

Solenoid Valves Kingston Superior 1000 Solenoid Valves are designed for use in difficult applications. Dirty Water Filter System is an ideal choice for Reclaim Water in industrial, car wash, truck wash and irrigation applications. Internally piloted, two-piece diaphragm is EPDM formulated for resistance to chlorine, chloramine and other chemical solutions. Unique design also reduces damaging vibrations from water hammer. Valve and copper line relieve solutions on top of diaphragm back into flow line when required.

Bypass is for manual flush or manual actuation

Brass construction and Nema 4X coils are rated for outdoor and wet environments. Rated from 20 to 150 PSI and -20° to +200° F. Available in 3/4” to 3” FPT sizes and 24 or 110 volt. D

FEATURES •

Dirty Water Filter System & (2) Piece Diaphragm Assembly

Produces Exceptional Flow Rated Performance

Stops Water Hammer in Its Tracks

NEMA 4X Rated Electrical Components

FPT Maximum Size Volts GPM Wt.

Part No.

KG KN1075075 KG KN1075100 KG KN1075125 KG KN1075150 KG KN1075200 KG KN1075300 KG KN1000075 KG KN1000100 KG KN1000125 KG KN1000150 KG KN1000200 KG KN1000300

3/4" 1” 1-1/4” 1-1/2” 2” 3” 3/4” 1” 1-1/4” 1-1/2” 2” 3”

110 110 110 110 110 110 24 24 24 24 24 24

15 30 60 90 160 260 30 30 30 30 30 30

2.35 lbs. 3.75 lbs. 5.00 lbs. 8.50 lbs. 9.50 lbs. 30 lbs. 2.35 lbs. 3.75 lbs. 5.00 lbs. 8.50 lbs. 9.50 lbs. 30 lbs.

D

Net Ea.

$ 124.50 146.00 168.00 196.00 238.00 1048.00 124.50 146.00 168.00 196.00 238.00 969.00

Operating Ranges: Flow: 5 to 360 GPM Pressure: 20 to 150 PSI Temperature: -20° to +200° F.

3-Way Solenoids 1/8” or 1/4” FPT • Stainless Steel Body • 3-Way Direct Acting • Universal Direct Acting, 3-Way Solenoid Valves. Available in 1/8” and 1/4” FPT ports. Stainless steel bodies with Viton® seals. Universal design can be used for Normally Open, Normally Closed or Diverting applications. Rated for air, oil or water solutions to 150 PSI. Ambient temperatures to 125° F. and fluid temperatures to 230° F. 110 volt and 24 volt conduit coil housings with 24” lead wires are standard but junction box, DIN, explosion-proof, 12 volt and 240 volt options are also available. Valves can be mounted in any position.

Part No.

Valve Type

GC S306-12A1 GC S306-22A1 GC S306-13B1 GC S306-23B1

3-Way Stainless 3-Way Stainless 3-Way Stainless 3-Way Stainless

DULTMEIER SALES

OMAHA, NE (800)

D

FPT AC Ports Volts Net Ea.

1/8” 1/8” 1/4” 1/4”

228-9666

24 Volt 110 Volt 24 Volt 110 Volt •

$ 77.95 77.95 77.95 77.95

DAVENPORT, IA (800)

Viton® is a registered trademark of DuPont Performance Elastomers

553-6975

www.dultmeier.com

E1028


Solenoid Valves

169

Any solenoid less coil, Deduct $3.00

400 Series Brass Bodies

General Purpose Solenoid Valves for on-off control of water, chemicals, air, oil, and gas. Available with brass or stainless steel bodies. Standard with Buna-N seals, (EPR, Viton® and other sealing materials also available). Exclusive stainless steel seat insert reduces wear and delivers longer life in brass bodied valves.

Low Pressure

D

24 & 110-Volt AC Normally Closed & Normally Open

These solenoid valves are all rated from 0 to 5 PSI as high as 200 psi operating pressure differential which allows them to be used in a wide variety of applications. Operational design is Piloted Diaphragm. Available in either normally closed or normally open options. All valves are standard with 24" lead wires

Used for controlling the flow of water, air, oil and various other (except hazardous) chemicals. Features: Temperatures to 200° F. maximum • Standard with molded waterproof coil • Electrical junction box (except on model 491P) • Pilot operation (except on 401P which is direct acting) & (473P, 474P & 476P which are BUNA diaphragm operated). • Teflon seal on T Series. 400 Series Valves *For pressure differential below 3-PSI remove closing spring.

WATER FLOW -GAL./MIN.

MODEL

S20 Series Solenoid Valves: • 2-Way Operation • Piloted Diaphragm Design • Normally Closed & Normally Open

PRESSURE DIFFERENTIAL - PSI

• Zero to 200 psi OPD.

NO. 1 2 5 10 20 50 401P 0.27 0.38 0.60 0.85 1.2 1.9 O412P 1.2 1.7 2.7 3.8 5.4 8.5 A413P* 2.0 2.8 4.5 6.3 8.9 14 A414P* 3.1 4.4 6.9 9.8 14 22 OA414P 3.1 4.4 6.9 9.8 14 22 A416P* 5.3 7.5 12 17 24 37 OA416P 5.3 7.5 12 17 24 37 A418P 8.0 11.0 18 25 36 58 424P-2 0.30 0.42 0.67 0.95 1.34 2.12 491P 0.20 0.28 0.44 0.63 0.89 1.4

FPT AC *Max O.P.D Part No. Material Valve Type Ports Volts Min. Max. Net Ea. GC S201-24 Brass Norm Closed 3/8" 24 0 140 $ 64.90 GC S201-10 Brass Norm Closed 3/8" 110 0 140 64.90 GC S203-24 Brass Norm Closed 1/2" 24 0 140 65.05 GC S203-10 Brass Norm Closed 1/2" 110 0 140 65.05 GC S207-24 Brass Norm Closed 3/4" 24 5 150 76.10 GC S207-10 Brass Norm Closed 3/4" 110 5 150 76.10 GC S210-24 Brass Norm Closed 1" 24 5 150 118.50 GC S210-10 Brass Norm Closed 1" 110 5 150 118.50 GC S211-24 Stainless Norm Closed 3/4” 24 5 150 126.50 GC S211-10 Stainless Norm Closed 3/4” 110 5 150 126.50 GC S212-24 Stainless Norm Closed 1” 24 5 150 159.00 GC S212-10 Stainless Norm Closed 1” 110 5 150 159.00 GC S230-24 Brass Norm Closed 1-1/4" 24 5 150 230.00 GC S230-10 Brass Norm Closed 1-1/4" 110 5 150 230.00 GC S250-24 Brass Norm Closed 1-1/2" 24 5 150 274.50 GC S250-10 Brass Norm Closed 1-1/2" 110 5 150 274.50 GC S270-10 Brass Norm Closed 2" 110 5 150 356.50 GC S270-24 Brass Norm Closed 2" 24 5 150 356.50 GC CS3-110 Replacement Coil, 110 Volt ..................................... 7.85 GC CS3-24 Replacement Coil, 24 Volt ....................................... 7.85 GC CS4-110 Replacement Coil, 110 Volt ..................................... 9.77 GC CS4-24 Replacement Coil, 24 Volt ....................................... 9.77 * Maximum Operating Pressure Differential.

Net Ea. $ 35.80 36.85 50.30 50.30 55.80 55.80 76.95 76.95 105.00 105.00 60.95 60.95 60.95 61.00 60.35 63.75 66.25 66.25 68.45 5.97 11.95 11.65 16.50 22.95

GC S202-24 Brass Norm Open 3/8" GC S202-10 Brass Norm Open 3/8" GC S204-24 Brass Norm Open 1/2" GC S204-10 Brass Norm Open 1/2" * Maximum Operating Pressure Differential.

D

463PS/464PS/466PS

200 200 200 200

88.70 88.70 88.95 88.95

Diaphragm Operated, Stainless Steel Solenoids. NormallyClosed valves feature corrosionresistant, stainless steel bodies. 24-Volt Models feature spade style coils. 110-Volt models have coils with 12” lead wires. Maximum operating pressure is 400 PSI. Buna diaphragms are standard on 476/478, EPDM on 463/464.

D

476PS & 478PS

Part No. DE 463PS-24 DE 464PS-24 DE 466PS-24 DE 476PS-24 DE 478PS-24 DE 463PS-110 DE 464PS-110 DE 466PS-110 DE 476PS-110 DE 478PS-110

For Any Solenoid Ordered Less the Coil - Call for Deduct Amount

228-9666

0 0 0 0

- Low Pressure -

Pressure AC FPT Flow Working Differential PSI Part No. VOLTS Ports @ 60 PSI Pressure Max. Min. Net Ea. DE O443P-24 24 3/8” 8 GPM 125 PSI 3 1 $ 59.50 DE O443P-110 110 3/8” 8 GPM 125 PSI 3 1 59.50 DE O473P-24 24 3/8” 27 GPM 300 PSI 150 1 85.60 DE O473P-110 110 3/8” 27 GPM 300 PSI 150 1 85.60 DE O474P-24 24 1/2” 31 GPM 300 PSI 150 1 85.60 DE O474P-110 110 1/2” 31 GPM 300 PSI 150 1 85.60 DE O476P-24 24 3/4” 39 GPM 300 PSI 150 1 90.75 DE O476P-110 110 3/4” 39 GPM 300 PSI 150 1 90.70 DE 04191-24V 24 Volt Replacement Coil for 0453P-24 Valve.......... 14.10 DE 04191-120V 110 Volt Replacement Coil for 0453P-110 Valve...... 14.10 DE 04192-24V 24 Volt Replacement Coil for 0473P-24, 0474P-24 & 0476P-24 Valves................ 17.95 DE 04192-120V 110 Volt Replacement Coil for 0473P-110, 0474P-110 & 0476P-110 Valves.......... 17.95

OMAHA, NE (800)

24 110 24 110

Stainless Steel Solenoids

Normally OPEN Valves Maximum

DULTMEIER SALES

D

(3/8” - 2”)

• Rated to 180° F.

Normally CLOSED Valves Maximum

Pressure AC FPT Flow Working Differential PSI Part No. VOLTS Ports @ 60 PSI Pressure Max. Min. DE 401P-24 24 1/4" 2 GPM 150 PSI 150 0 DE 401P-110 110 1/4" 2 GPM 150 PSI 150 0 DE A413P-24 24 3/8" 15 GPM 400 PSI 150 3 DE A413P-110 110 3/8" 15 GPM 400 PSI 150 3 DE A414P-24 24 1/2" 24 GPM 400 PSI 150 3 DE A414P-110 110 1/2" 24 GPM 400 PSI 150 3 DE A416P-24 24 3/4" 39 GPM 400 PSI 150 3 DE A416P-110 110 3/4" 39 GPM 400 PSI 150 3 DE A418P-24 24 1" 62 GPM 400 PSI 150 3 DE A418P-110 110 1" 62 GPM 400 PSI 150 3 DE 473P-24 24 3/8" 27 GPM 300 PSI 150 1 DE 473P-110 110 3/8" 27 GPM 300 PSI 150 1 DE 474P-24 24 1/2" 31 GPM 300 PSI 150 1 DE 474P-110 110 1/2" 31 GPM 300 PSI 150 1 DE 474PT-110 * 110 1/2" 31 GPM 300 PSI 150 1 DE 474PT-12 * 12 1/2" 31 GPM 300 PSI 150 1 DE 476P-24 24 3/4" 39 GPM 300 PSI 150 1 DE 476P-110 110 3/4" 39 GPM 300 PSI 150 1 DE 476PT-12 * 12 3/4" 39 GPM 300 PSI 150 1 DE RK401 Repair Kit, 401 Valves........................................ DE RK413 Repair Kit, 413 Valves........................................ DE RK414V Repair Kit, 414 Valves........................................ DE RK416V Repair Kit, 416 Valves........................................ DE RK418 Repair Kit, 418 Valves........................................ * Teflon Fitted

Low Pressure Solenoids

Pressure FPT Flow Differential PSI Ports Volts @ 60 PSI Min. Max. 3/8” 24 15 GPM 0 150 1/2” 24 15 GPM 0 150 3/4” 24 16 GPM 0 150 3/4” 24 38 GPM 0 150 1” 24 100 GPM 0 150 3/8” 110 15 GPM 0 150 1/2” 110 15 GPM 0 150 3/4” 110 16 GPM 0 150 3/4” 110 38 GPM 0 150 1” 110 100 GPM 0 150

Net Ea. $ 47.20 47.45 50.50 145.50 145.00 45.90 47.25 50.65 141.00 140.50

Viton® is a registered trademark of DuPont Performance Elastomers

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0099


Solenoid Valves

170 High Pressure Solenoid Valves

Vacuum Solenoids DEMA 481/482 Series Solenoids for vacuum applications, such as inlet side of pump. Rated to 200° F. Valve bodies are PVC with EPDM seal. Available in 1/8" and 1/4” FPT ports and in 12, 24 or 110 volt. 482 Models have adjustable flow screws.

481P

D

Part No.

Volts

DE 481P-12 DE 481P-110 DE 481P-24 DE 482-2-12 DE 482-2-120 DE 482-2-24 DE 4191-24V DE 4191-120V

Flow @ 60 PSI

12 Volt DC 110 Volt AC 24 Volt AC 12 Volt DC 110 Volt AC 24 Volt AC

24-Volt Replacement Coil ONLY...... 110-Volt Replacement Coil ONLY....

454P

453P

24 & 110 Volt

450 SERIES HIGH PRESSURE: These piston style solenoid valves have a maximum working pressure of 1500 PSI. Minimum pressure differential 10 PSI, Maximum pressure differential 1200 PSI. Brass body construction. Standard with molded waterproof coil and electrical junction box. Valves are rated for 200° F. fluid and 120° F. ambient temperatures. Valves can be mounted in any position. Buna seal. Not for use with Hazardous or Corrosive fluids. Normally closed except for “O” Series, which are normally open.

15.35 15.35

Dual Solenoid Assembly Dual Solenoid Assembly is designed to replace the “Old Style” Dole Dual Solenoids. This assembly features (2) 24-Volt solenoids with built-in strainers, brass inlet tee and 3/4” MGHT brass inlet fittings. Ideal for use on pump stations and supply tanks.

4195 Coils

FPT Part No. AC-VOLTS PORTS FLOW @ 60 PSI Net Ea. DE 453P-24 24 3/8" 14-GPM $ 68.60 DE 453P-110 110 3/8" 14-GPM 68.60 DE 453PS-110 * 110 3/8" 14-GPM 75.50 DE 453PS-24 * 24 3/8" 14-GPM 75.50 DE 454P-24 24 1/2" 29-GPM 102.50 DE 454P-110 110 1/2" 29-GPM 102.50 DE 458P-24 24 1" 86-GPM 175.00 DE 458P-110 110 1" 86-GPM 174.50 DE 458PS-110 * 110 1" 86-GPM 189.00 DE 458PS-24 * 24 1" 86-GPM 189.00 DE O453P-24 ** 24 3/8” 14 GPM 91.60 DE O453P-110 ** 110 3/8” 14 GPM 93.30 DE RK453 Repair Kit for 453 Series ............................................. 34.30 DE RK454 Repair Kit for 454 Series ............................................. 29.35 DE RK458 Repair Kit for 458 Series ............................................. 51.45 * With stainless steel piston. Used on many OEM applications. ** Normally Open.

D

Volts 24 Volt

D

Net Ea.

2.1 GPM $ 61.15 2.1 GPM 58.65 2.1 GPM 59.20 2.1 GPM 64.10 2.1 GPM 61.55 2.1 GPM 61.55

Part No. DU P443ASSY

D

High Pressure Stainless Steel Solenoid Valves

Net Ea. $ 64.80

• 2-Way

D

• High Pressure

Solenoid Coils Junction Box Coils

• Piloted Piston Operation D

• Stainless Bodies

D

• Teflon Seats Spade Coils

Din Coils

D

• 15 - 1200 PSI OPD

Part No. Volts Type For Dema Valves Net Ea. DE 4191-12V 12VDC Junction Box 401 / 424 / 481 / 482 / 473 / 474 / 476P $ 17.60 DE 4191-120V 120VAC Junction Box 401 / 424 / 481 / 482 / 473 / 474 / 476P 15.35 DE 4191-24V 24VAC Junction Box 401 / 424 / 481 / 482 / 473 / 474 / 476P 15.35 DE 4191-24VDC 24VDC Junction Box 401 / 424 / 481 / 482 / 473 / 474 / 476P 17.60 DE 4191-240V 240VAC Junction Box 401 / 424 / 481 / 482 / 473 / 474 / 476P 15.35 DE 4191D-120 120VAC Din 401 / 424 / 481 / 482 / 473 / 474 / 476P 16.45 DE 4191D-24 24VAC Din 401 / 424 / 481 / 482 / 473 / 474 / 476P 16.45 DE 4191D-24DC 24VDC Din 401 / 424 / 481 / 482 / 473 / 474 / 476P 17.15 DE 4192-12V 12VDC Junction Box 412 / 413 / 414 / 416 / 418/ 453 / 454 / 458 20.20 DE 4192-120V 120VAC Junction Box 412 / 413 / 414 / 416 / 418/ 453 / 454 / 458 17.95 DE 4192-24V 24VAC Junction Box 412 / 413 / 414 / 416 / 418/ 453 / 454 / 458 17.95 DE 4192-24VDC 24VDC Junction Box 412 / 413 / 414 / 416 / 418/ 453 / 454 / 458 20.20 DE 4192-240V 240VAC Junction Box 412 / 413 / 414 / 416 / 418/ 453 / 454 / 458 17.95 DE 4192D-120 120VAC Din 412 / 413 / 414 / 416 / 418/ 453 / 454 / 458 18.95 DE 4192D-24 24VAC Din 412 / 413 / 414 / 416 / 418/ 453 / 454 / 458 18.95 DE 4192D-24VDC 24VDC Din 412 / 413 / 414 / 416 / 418/ 453 / 454 / 458 23.65 DE 4195-12 12VDC Junction Box 442 / 443 / 462 / 463 / 464 8.08 DE 4195-120V 120VAC Junction Box 442 / 443 / 462 / 463 / 464 6.63 DE 4195-220 240VAC Junction Box 442 / 443 / 462 / 463 / 464 6.63 DE 4195-24 24VAC Junction Box 442 / 443 / 462 / 463 / 464 6.63 DE 4195-24DC 24VDC Junction Box 442 / 443 / 462 / 463 / 464 7.79 DE 41-9-7-6 120VAC Spade 491 / 492 / 476PS / 478PS 7.57 DE 41-9-7-3 24VAC Spade 491 / 492 / 476PS / 478PS 7.57 DE 04192-12V * 12VDC Junction Box O412 / O414 / O416 / O418 / O453 / O454 20.45 DE 04192-120V * 120VAC Junction Box O412 / O414 / O416 / O418 / O453 / O454 17.95 DE 04192-24V * 24VAC Junction Box O412 / O414 / O416 / O418 / O453 / O454 17.95 * 0 Prefix signifies Normally Open Coils. Note: Junction Box Coils rated Nema 1. Din & Conduit Coils rated Nema 4. DULTMEIER SALES

(S Series)

• 24 or 110 Volt

OMAHA, NE (800)

228-9666

• Normally Closed

(H Series)

D

• Conduit Coils • Viton® Seals Viton® is a registered trademark of DuPont Performance Elastomers

S Series Part No. GC S401-24 GC S401-10 GC S408-24 GC S408-10

Valve Type Norm Closed, SS Norm Closed, SS Norm Closed, SS Norm Closed, SS

FPT AC Ports Volts 3/8" 24 3/8" 110 1/2" 24 1/2" 110

Flow @ 60 PSI 14 GPM 14 GPM 32 GPM 32 GPM

Norm Closed, SS Norm Closed, SS Norm Closed, SS Norm Closed, SS

3/4” 3/4” 1” 1”

54 GPM $ 185.00 54 GPM 185.00 85 GPM 219.50 85 GPM 219.50

Net Ea. $ 80.10 80.10 91.95 91.95

H Series GC H901-24 GC H901-10 GC H902-24 GC H902-10

24 110 24 110

Replacement Coils Part No. Net Ea. GC CS4-110 Replacement Coil, 110 Volt, S Series ...................... $ 9.77 GC CS4-24 Replacement Coil, 24 Volt, S Series ........................ 9.77 GC HS4-110 Replacement Coil, 110 Volt, H Series....................... 25.30 GC HS4-24 Replacement Coil, 24 Volt, H Series......................... 25.30 DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0098


Miniature Solenoid Valves

171

Solenoid/Strainer Valves Diaphragm Operated Solenoid/Strainer Combo Units. 442P & 443P are brass construction. P442 & P443 are celcon plastic construction. Used for controlling the flow of water, air, oil and various other (except hazardous) chemicals. Features: • Temperatures to 200° F. maximum • Standard with molded waterproof coil • Mount in any position except with the coil under the valve • Electrical junction box • Stainless steel seat • EPDM seal • Pilot operation which are direct acting. Pressures to 125 PSI.

Stainless Solenoids Stainless Steel Kip Solenoids are ideal for soap, wax, tire cleaner or pre-soak systems. Standard Features include Stainless steel bodies and internal parts for exceptional wear life. Viton® upper seal & BUNA lower seal for bubble-tight sealing and long life. 24-volt or 110-volt AC coils. Molded spade terminal coil is standard on 24-volt & enclosed coil on 110-volt. Maximum operating pressure differential is 150 PSI. Ports are either 1/4" or 1/8" FPT. Standard valves are 2-Way, normally closed. UL listed.

Model 442P Brass Body

249014-023101 has a metering screw in bottom.

Model P443 Celcon Body

Pressure AC FPT Flow @ Differential PSI Body Volts Ports 60 PSI Max. Min. Brass 24 1/4" 7.75 GPM 125 3 Brass 110 1/4" 7.75 GPM 125 3 Brass 24 3/8" 7.75 GPM 125 3 Brass 110 3/8" 7.75 GPM 125 3 Celcon 24 1/4" 7.75 GPM 125 3 Celcon 110 1/4" 7.75 GPM 125 3 Celcon 24 3/8" 7.75 GPM 125 3 Celcon 110 3/8" 7.75 GPM 125 3 24-Volt Replacement Coil ONLY............................. 110-Volt Replacement Coil ONLY...........................

No. 3X293 Side Meter

Net Ea. $ 26.75 26.75 26.95 26.95 19.95 19.95 19.95 19.95 6.63 6.63

D

Part No.

Metering

No. PA3X293 Plunger

KI RK3X293AC KI RK3X293VV KI PA3X293 KI PA3X293VV KI 2-30-0246

D

No. 249014-023101 Bottom Meter

AC Volts

PORTS

Net Ea.

24 24 24 110 24 110

1/8" FPT 1/4" FPT 1/8" FPT 1/8" FPT 1/4" FPT 1/4" FPT

$ 37.85 39.90 32.50 33.25 26.75 27.50

KI 249014-023101 Yes, Bottom KI 3X293 Yes, Side KI 249015 No KI 249015-10 ** No KI 359015 No KI 359015-10 ** No

Stainless Steel Normally Closed

* (EP) Repair Kit . ........................................ (Viton®) Repair Kit....................................... * Replacement Plunger with EPR Seat ....... Replacement Plunger with Viton® Seat........ 24-Volt Replacement Coil with Spades ......

* EP Kits are best for Tire Cleaner Products ** 110 Volt Solenoids feature 12" lead wire on coils, not spade mount.

424P SERIES This normally closed direct acting, Stainless body Solenoid Valve may be used directly in chemical lines. • Excellent corrosion resistance • Pressure differential range - 0 to 150 PSI • Maximum working pressure is 150 PSI • Temperatures to 200° F. • Buna seal.

D

249015 & 359015 are the same valves as above but do not include the built-in metering screw feature.

D

Part No. DE 442P-24 DE 442P-110 DE 443P-24 DE 443P-110 DE P442-24 DE P442-110 DE P443-24 DE P443-110 DE 4195-24 DE 4195-120V

No. 359015

3X293 & 3X529-10 have a Stainless Steel metering screw incorporated into the side of the body and are designed for individual use.

D

D

D

23.80 22.35 6.38 6.55 10.65

Low Pressure Solenoids S30 Series Solenoid Valves: • 2-Way, Zero Differential

Part No. PORTS AC-VOLTS Flow@60 PSI Net Ea. DE 424-2-12 1/4" FPT 12 2.3 GPM $ 40.95 DE 424-2-24 1/4" FPT 24 2.3 GPM 37.85 DE 424-2-110 1/4" FPT 110 2.3 GPM 37.90 DE 4191-24V 24 Volt Coil......................................... 15.35 DE 4191-120V 120 Volt Coil....................................... 15.35

• Direct Acting Operation

(1/4”)

D

• Brass or Stainless Bodies • Buna Seal

Stainless Solenoids Stainless Steel Solenoids from Dema. Available with or without metering screws for chemical control. 24-Volt valves feature spade mount coils for ease in wiring. 110-Volt valves are standard with 12" lead wires for added safety. Direct acting valves with Buna seals. Pressure differential is 0-150 psi. Standard valves are 2-way normally closed.

D

492SM with Metering Screw

Voltage Metering Ports 60 PSI Net Ea. 24 Volt No 1/4" FPT 2 GPM $ 31.20 110 Volt No 1/4" FPT 2 GPM 30.45 24 Volt Yes 1/4" FPT 2 GPM 36.20 110 Volt Yes 1/4" FPT 2 GPM 35.65 * 24 Volt Coil ONLY, with spades, 492........... 7.57 * 110 Volt Coil ONLY, with lead wires, 492.... 7.57

Net Ea. $ 44.60 44.60 44.45 44.45 9.77 9.77

Dual Inlet Solenoid Valve

Outlet

Flow @

Part No. DE 492S-24 DE 492S-110 DE 492SM-24 DE 492SM-110 DE 41-9-7-3 DE 41-9-7-6 * For 492 Series.

FPT AC *Max O.P.D Part No. Valve Type Ports Volts Min. Max. GC S301B-24 Norm Closed, Brass 1/4" 24 0 150 GC S301B-10 Norm Closed, Brass 1/4" 110 0 150 GC S303S-24 Norm Closed, SS 1/4" 24 0 150 GC S303S-10 Norm Closed, SS 1/4" 110 0 150 GC CS4-110 Replacement Coil, 110 Volt ....................................... GC CS4-24 Replacement Coil, 24 Volt ......................................... * Maximum Operating Pressure Differential.

Control both hot and cold water with one valve. Two 3/4" male Garden Hose inlet ports and one 3/8" FPT discharge port. 24-Volt AC.

D

Inlets

Part No. DU 33812-24 24-Volt Solenoid............. DE 41-15-10 Replacement Diaphragm

Net Ea. $ 46.75 1.58

Viton® is a registered trademark of DuPont Performance Elastomers

E0960


Miniature Solenoid Valves

172

2X911VM4

Manifold Solenoid Assemblies

Manifold/Solenoid Assemblies Brass or Stainless

D

Outlets

D

2X911-24

Inlet

Manifold Style: Stainless solenoid valves mounted on solid Brass manifold blocks. Individual metering screws for each solenoid on 2X911 Series. Common inlet port for chemical supply to all valves. Viton® seals. Rated to 150 PSI. AC Metering Part No. Volts PORTS # Valves Screws Net Ea. KI 2X911VM1 24 1/4" FPT 1 Yes $ 39.65 KI 2X911VM2 24 1/4" FPT 2 Yes 70.95 KI 2X911VM3 24 1/4" FPT 3 Yes 97.90 KI 2X911VM4 24 1/4" FPT 4 Yes 129.50 KI 2X911VM5 24 1/4" FPT 5 Yes 161.50 KI 2X911VM6 24 1/4" FPT 6 Yes 188.50 KI 2X910VM1 24 1/4" FPT 1 No 36.90 KI 2X910VM2 24 1/4" FPT 2 No 54.20 KI 2X910VM3 24 1/4" FPT 3 No 72.90 KI 2X910VM4 24 1/4" FPT 4 No 97.45 KI 2X910VM5 24 1/4" FPT 5 No 121.50 KI 2X910VM6 24 1/4" FPT 6 No 141.50 KI 2X911-24 KI RK3X293AC KI RK3X293VV KI PA3X293VV KI PA3X293 KI 2155-0246

Replacement Valve Only...................................... *(EP) Repair Kit ................................................. (Viton®) Repair Kit .............................................. Replacement Plunger with Viton® Seat.................. *Replacement Plunger with EPR Seat ................ 24-Volt Replacement Coil ..................................

34.75 23.80 22.35 6.55 6.38 23.95

*Best for Tire Cleaner Products

Bare Brass Manifold Blocks

D

93-000-21M

Brass Manifold Blocks with or without metering screws for flow adjustment. Available in 1 through 6 banks. No solenoid control. Ideal for chemical or weep water lines. Ports are 1/4” FPT. Makes plumbing applications compact and neat. Rated to 1000 PSI.

Part No. Banks Metering Net Ea. GC 92-000-21 2 No $ 26.40 GC 93-000-21 3 No 34.75 GC 94-000-21 4 No 42.75 GC 95-000-21 5 No 50.95 GC 96-000-21 6 No 60.95 GC 91-000-21M 1 Yes 34.00 GC 92-000-21M 2 Yes 53.95 GC 93-000-21M 3 Yes 72.95 GC 94-000-21M 4 Yes 92.50 GC 95-000-21M 5 Yes 111.50 GC 96-000-21M 6 Yes 129.50

Low Pressure Brass or Stainless Manifold Assemblies allow one chemical in and open/closed option for 2 to 5 banks. Compact design for space saving installations. 24-Volt coils and Viton® seals are standard. Available with either 1/4” x 1/4” FPT ports or in high flow, 1/2” FPT inlet x 3/8” FPT outlet ports. Also available with or without chemical metering screws. Rated to 150 PSI.

D

Brass Metering Screws

Inlet 1/4” or 1/2”

Stainless Steel D

Outlets 1/4” or 3/8”

Part No. Valves Material Metering Outlet Net Ea. DE 4921 1 Brass No 1/4” $ 32.75 DE 4922 2 Brass No 1/4” 60.05 DE 4923 3 Brass No 1/4” 86.70 DE 4924 4 Brass No 1/4” 115.00 DE 4925 5 Brass No 1/4” 137.00 DE 492M1 1 Brass Yes 1/4” 34.85 DE 492M2 2 Brass Yes 1/4” 66.45 DE 492M3 3 Brass Yes 1/4” 96.30 DE 492M4 4 Brass Yes 1/4” 126.50 DE 492M5 5 Brass Yes 1/4” 152.50 DE 492M2SS 2 Stainless Yes 1/4” 96.50 DE 492M3SS 3 Stainless Yes 1/4” 137.00 DE 492M4SS 4 Stainless Yes 1/4” 187.00 DE 492M5SS 5 Stainless Yes 1/4” 223.00 DE 464M-3-16-3 3 Stainless No 3/8” 141.00 DE 464M-4-16-3 4 Stainless No 3/8” 173.50 DE 464M-5-16-3 5 Stainless No 3/8” 218.50 DE 41-9-7-3 24-Volt Coil, 492 Series.............................. 7.57 DE 4195-24 24-Volt Coil, 464 Series.............................. 6.63 DE 49-3-V Replacement Plunger, Viton®..................... 11.85

Poly Manifold This Poly Manifold has a 3/4" FPT inlet, eight 1/2" FPT outlet ports and a 1/4" FPT gauge port. Maximum pressure is 100 PSI. Maximum Temperature is 150° F. D

Part No.

Net Ea.

TK TM075/050 $ 19.35 8-WAY MANIFOLD

Polypropylene Gauge Tee Visit Our Web Site at http://www.dultmeier.com or E-Mail us at

— 1/4” Gauge Port Inside of All Tees — Gauge Port

dultmeier@dultmeier.com

D

Size Gauge Part No. FPT Ports Port Net Ea. TW GTT1214 1/2" 1/4"FPT $ 2.04 TW GTT34-14 3/4" 1/4"FPT 2.28 TW GTT100-14 1" 1/4"FPT 5.23 TW GTT114-14 1-1/4" 1/4"FPT 6.95 TW GTT112-14 1-1/2" 1/4"FPT 7.50

Viton® is a registered trademark of DuPont Performance Elastomers

E0100


Fuel Pumps • Solenoids • Switches

173

Fuel Pumps

ST5 / ST5H / ST505

High Pressure Flow Switches

Oil Burner Pumps from Suntec. Suitable for use with kerosene, No. 1 or No. 2 Fuel Oil. (Waste Oil Pumps also available). Pumps are designed to be gravity fed fuel oil from your holding tank and to then pressurize the fuel to a nozzle. Single-stage pumps are for medium lift applications and can be mounted in any position. Two-stage pumps are for high lift, long run applications and can be mounted in any position except upside-down. All pumps are factory set at 100 PSI but are adjustable from 100-150 PSI.

ST5 Flow Switch (Medium Flow). Rated from 1 to 8 GPM. Vertical mount only. Rated to 4400 PSI. Brass/plastic construction. Maximum temperature is 176° F. 3/8” FPT ports. 250 Volt, 3 Amp. 47” Cord. ST5H Flow Switch (High Flow). Rated from 1 to 16 GPM. Mounts in any position. Rated to 3100 PSI. Brass/plastic construction. Maximum temperature is 176° F. 3/8” FPT ports. 250 Volt, 3 Amp. 47” Cord. ST505 Flow Switch (Medium Flow - High Pressure). Rated from 1 to 8 GPM. Vertical mount D only. Rated to 7300 PSI. Stainless/ plastic construction. Maximum ST6 temperature is 176° F. 3/8” FPT ports. 250 Volt, 3 Amp. 47” Cord.

D

No. A2VA-7116

Available in 1725 RPM or 3450 RPM models. * Shaft rotation and nozzle port location is either RH or LH as viewed from the shaft end.

ST6 Flow Switch (Medium Flow). Rated from 1 to 8 GPM. Mounts in any position. Rated to 4500 PSI. Brass construction. Maximum temperature is 176° F. 3/8” MPT inlet and outlet with 1/4” FPT gauge port. 250 Volt, 3 Amp. 47’ Cord.

Part No. Max. Flow Max. PSI Net Ea.

NP ST5 8 GPM NP ST5H 16 GPM NP ST505 8 GPM NP ST6 8 GPM

4400 $ 27.85 3100 58.90 7300 85.75 4500 28.95

Flow Switches FS8

Model FS8 Flow Switch is rated to 3600 PSI and up to 8 GPM. Electrical ratings to 230 volt, 3 amp. Ports are 3/8" MPT. Must be mounted in vertical position to function properly. Maximum temperatures to 175° F.

D

No. J4NB-A1000G

Many Other Models Available! * Rotation & Rated Part No. RPM Nozzle Port PSI

SD A2VA-7116 3450 SD A1YA-7912 1725 SD J4NB-A1000G 1725 SD B2TA-8249 3450 SD B2YA-8916 3450 SD A2YA-7916 3450

RH/RH RH/RH RH/LH RH/RH RH/RH RH/RH

GPH

Net Ea.

150/200 3/2 $ 60.85 100/150 7/3 98.65 80 24 215.00 150/300 18/16 159.50 150/200 7/3 143.50 150/200 7/3 105.50

Fuel Solenoids Suntec Solenoid Shutoff Valves for use with Kerosene No. 1 or No. 2 fuel oil. Available in 24V, 115V or 220V. All shown are Non-Delay opening response. Standard with 19" lead wires. "R" Series are pump mount style. "C" Series are burner mount. Rated to 300 PSI.

D

Voltage

Mount

D

Model 100975 Flow switch is rated to 12 gpm and 5000 psi. Can be mounted in any direction. (3) magnet design means shuttle will not stick. Rated to 5 amp and 250 volt. Ports are 3/8" FPT. Maximum temperatures to 180° F.

100975

D

Model 100879 and 100904 Flow Switches feature micro-switch technology which eliminates the reed switch. Valves activate on as little as 1/2 gpm flow. Maximum flows to 10 gpm. Valves can be mounted in any position. Rated to 4000 psi, 250 volts and 180° F. Switch rating is 5 amps. Ports are 3/8" FPT. Model 100879 has a "pilot" feature for use with gravity feed systems. Model 100904 is for pressure feed systems and does not have the pilot feature.

* As viewed from shaft end.

Part No.

D

4’ Cord

Net Ea.

SD R261NL 24AC/12DC Pump $ 42.95 SD C261NR 24AC/12DC Burner 39.50 SD R642NL 115 Pump 37.85 SD C642NR 115 Burner 37.65 SD R753NL 220 Pump 37.60 SD C753NR 220 Burner 37.65 SD PVR38 Oil Safety Valve............. 64.95

Model 103011 and 100329 are designed to provide on/off switching for systems that require stop/start capability. Operating range is .75 to 18 GPM. Rated for 3 amp up to 250 volt. Maximum temperatures to 165° F. Construction is brass body with stainless and Buna internals. Ports are 3/8". 103011 is designed for pressure feed systems. 100329 has a “pilot feature” for gravity feed systems. Max. Min. Max. Part No. Pressure Flow Flow IP FS8 3600 PSI 1.0 GPM 8 GPM IP 100904 4000 PSI .5 GPM 10 GPM IP 100879 * 4000 PSI .5 GPM 10 GPM IP 100975 5000 PSI .75 GPM 12 GPM IP 103011 4000 PSI .75 GPM 18 GPM IP 100329 * 5000 PSI .5 GPM 16 GPM * Best for Prep Units.

100879

D

103011

D

Net Ea. $ 34.40 80.55 91.40 34.35 132.50 136.00

100329

D

Pressure Switches Designed to be used for Normally “on” or Normally “off” applications. Switches are rated to 250 volts and 5 or 15 amps as noted. Ports are either 1/4" MPT or 3/8" MPT. Rated to 3600 PSI and 194° F.

D

Actuation Amp Part-No. Ports Pressure Rating Net Ea. GU 23180 1/4" MPT 360 PSI 5 amp $ 15.00 GU 23181 1/4" MPT 580 PSI 5 amp 15.30 GU 23175 1/4" MPT 580 PSI 15 amp 22.00 GU 23178 3/8" MPT 360 PSI 15 amp 25.00 DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0101


Parts / Hot Water Machines Burner Transformers

Scale Reducer Filter Scaltrol Scale Reducer Filter. Protects pumps and coils from minerals, staining and scale buildup. Designed for inlet, cold water supply lines. Ports are 3/4” FPT.

10,000 Volt Spark • 115 or 230 Volt

Part No. WT 20358 WT 21153

D

Part No. WT 21427 WT 20289

Description Net Ea. 115 Volt, 60 Hz, Side Hinge............. $ 82.85 230 Volt, 60 Hz, Side Hinge............. 91.05

Fuel Filters

Description Net Ea. Scale Reducer Filter/Cartridge....... $ 209.50 Replacement Cartridge.................. 156.00

Fan Blower Wheels

D

D

Burner Transformers from Wayne

Rated to flows up to 10 gpm and pressures to 55 psi. Designed to treat up to 50,000 gallons of water. Maximum temperature is 125˚ F. Replacement cartridges also available. Part No. WT SC50 WT RSC50

174

2330 D

D

308

Replacement Fan Wheels for Wayne Burners. Aluminum construction. Set screws are included.

Description Net Ea. 4-1/4” Diameter x 3-7/16” Wide........ $ 11.70 6-1/4” Diameter x 4” Wide................ 23.10

D

Part No. WT 308 WT 308-01 WT 2330 WT 4142

Fuel Filters with easy-todrain bowls. Protects fuel pumps from contaminants. Convenient, spin-on design makes replacing elements easy. Ports are 1/4” FPT. Model 308 is Racor brand. Model 2330 is an economical imported filter.

Description Net Ea. Racor Filter Complete........................... $ 49.40 Racor Replacement Element................ 19.75 Import Filter Complete.......................... 28.55 Import Replacement Element............... 12.70

Robertshaw Gas Valves

Burner Motors Replacement Burner Motors from Wayne • 3450 RPM D

115 or 230 Volts • 1/5 or 1/4 HP

Part No. WT 20554 WT 21328 WT 21126 WT 20388

Universal 1” Gas Valves from Robertshaw. Rated to 720,000 BTU (Natural Gas) and 1,150,000 BTU (LP).

Independent, automatic pilot valve. Manual gas cock. Available for standing Description Net Ea. pilot or electronic ignition. Available in 12 Volt or 208/230 Volt. 1/5 HP, 115 Volt, 60 Hz Motor.......... $ 105.00 1/5 HP, 230 Volt, 60 Hz Motor.......... 107.50 1/4 HP, 115 Volt, 60 Hz Motor.......... 165.00 Part No. Description Net Ea. 1/4 HP, 230 Volt, 50/60 Hz Motor..... 170.50 WT 00400 12 VDC/24 VAC, Electronic ignition, Natural Gas. $ 203.50 WT 00400L 12 VDC/24 VAC, Electronic ignition, LP Gas........ 203.50 WT 00411 120 VAC, Standing Pilot, Natural Gas................... 187.50 WT 00414 120 VAC, Standing Pilot, LP Gas.......................... 187.50 WT 00409 230 VAC, Standing Pilot, Natural Gas................... 187.50 WT 00415 230 VAC, Standing Pilot, LP Gas.......................... 187.50

Burner Ignitors

D

Solid State Burner Ignitors. 20,000 volt peak. Available with side or rear hinge mounting plate. Rated for 12 volts.

Cam Switches

D

Part No. WT 99001 WT 99002

Description Net Ea. 12 Volt Ignitor, side hinge plate........ $ 159.50 12 Volt Ignitor, rear hinge plate........ 130.50

We Can Supply Most

Available in 110 Volt or 220 Volt.

D

Voltage Part No. Description Rating Net Ea. WT F741A Off/Pump/Burner Switch 110 Volt / 1PH $ 19.80 WT F743A Off/Pump/Burner Switch 220 Volt / 1PH 25.95 WT F747A Off/Pump/Burner Switch 220 Volt / 3PH 39.10

Any Replacement Coils - Call for Pricing! DULTMEIER SALES

Heavy Duty Cam Switches for burner and pump control. Positive contacts. Includes legend plate and knob. Switches are held in place with a locking nut on the backside of the switch.

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0727


SECURITY LOCKS

175

High Security Disc Locks Stainless Steel Disc Locks that offer more key security that the other disc locks on the market. Both lock styles have stainless steel cases and hardened 3/8" steel shackles. Where these locks are different is in key security. Lock diameter is 2-3/4". Model S570D features a round tubular key which is more secure than standard flat keys offered on many other disc locks.

e “Th l” ina g i r O

“Diskus” Stainless Steel Padlocks

Model 24ST-70 “Diskus” Padlocks. Stainless Steel construction with stainless shackle for extra protection. 2.2 mm stainless case is the strongest padlock in it's class. 5-Pin cylinder. Diameter is 2-3/4". Locks are available keyed alike in a variety of key numbers.

D

Model 24RK70 “Diskus” Locks are the same as the 24ST70 but with a rekeyable feature to change key numbers if required.

24ST70

Model S670D goes even further, it features a restricted, half-moon key cut which is limited to your specific locations.

Model 2670 “Diskus” Locks are the same as the 24ST70 but also feature a “free spinning” drill guard for added drill out protection.

D

Model S670D

Model S570D

All locks are shipped direct from the factory for further key protection. Locks are sold single or in multiples and are keyed alike to meet your needs.

D

Series 2870 “Buffo” Locks have a 2.2 mm Stainless case and a 4 pin cylinder. Diameter is 2-3/4". A more economical option to the locks shown above.

D

L500 Lock Guards are stainless steel construction and give additional protection against bolt cutters, hammers and tampering.

24RK70-613 shown with Lock Guard Part No.

D

Part No.

Lock Style

Net Ea.

IX S570D Disc Lock, Round Tubular Key............ $ 22.55 IX S670D Disc Lock, Half-Moon, Restricted Key. 26.95 AK L500 Lock Guard.......................................... 4.96

L500 Lock Guard

Model 40 Disc Lock Master Disc Lock for heavy-duty security applications. Standard features: • Stainless Steel case • Hardened, 3/8" steel shackle is shielded for added protection against bolt cutters, saws and crowbars • Double locking deadbolt and precision pin tumbler mechanism prevent picking and unauthorized key use • Interior anti-saw pins deter cutting through the body • Diameter is 2-3/4".

D

ML20 Plug Lock

Description

Net Ea.

DU ML20 Plug Lock, MEDECO * Note: One key with each lock.

Net Ea.

AK 24ST70 Abus Diskus Padlock, keyed alike..................... $19.80 AK 24RK70-613 Abus Diskus Padlock, re-keyable keyed alike *. 26.00 AK 2670 Abus Diskus Padlock, with drill guard, keyed alike 19.80 AK 2870 Abus Buffo Lock, keyed alike................................ 14.00 AK 2870-293 Abus Buffo Lock, keyed alike *.................. 14.00 AK L500 SS Lock Guards............. 4.96 * Special Key Numbers for Special Pricing.

Plug Lock High Security Key Cuts for Wall Safes

Part No.

“No Imit t an atio n”

D

Part No.

$ 22.95

MR 40KAD AK L500

Diameter

SS Disc Lock - Keyed Alike 2-3/4" SS Lock Guard................................

Net Ea.

$ 11.15 4.96

Brass Pin Locks 635200

Solid Brass Pin Locks for Coin Meters or Vacuums. With this design, the lock is virtually tamper-proof. Lock is 1-1/2" x 1-1/2". Chrome-plated steel pin is 3/8" diameter with 5/8" clearance. Available keyed alike. Some special key codes are available on a special order basis but prices may be higher.

Call Us For All Your Car Wash & Truck Wash Needs! DULTMEIER SALES

OMAHA, NE (800)

228-9666

D

Part No.

D

Pin Only

Net Ea.

DY 635200 Pin Lock, Keyed Aliked...................... $ 11.80 DY 104802 Pin only as replacement, Plated........ 3.31

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0149


SECURITY LOCKS

176

Round "Puck" Style Padlocks

Pro Series Padlocks

Hidden Shackle, Round “Puck” Locks. Great physical security, defies bolt cutters and prying. All locks are 2-7/8” diameter with 1-1/2” thick bodies. Locking shackles are 3/8”. Commonly used in a wide variety of applications including coin meters, bill meters and vacuum money doors. All locks are keyed alike. Some models shown feature drilled and tapped holes in back where required.

Pro Series Padlocks from Master Lock. High security padlocks for industrial or commercial applications. Designed to withstand the most aggressive of physical attacks.

American A2000/A2000T. Solid steel, die cast body is reinforced with anti-saw pins. 6-pin tumbler provides superior pick resistance. A2000T is the same as A2000 but features drilled and tapped mounting holes on the back of the lock. Mounting Holes

LAI 2000SP features solid steel body but also includes “Tri-Cut” keys for added security and unique key numbers on each order. Standard with drilled and tapped mounting holes on back.

D

D D

Master 6270. Chrome plated, solid steel body. Features hardened steel construction. Drill holes are not available on this model.

Standard features include: Hardened BORON alloy steel shackle protects against sawing or cutting • Dual ball-bearing locking design protects against prying and hammering • Laminated steel body for high impact resistance • Five-pin cylinders make these locks virtually impossible to pick • Weather-resistant thermal plastic lock cover to keep out the elements. 6321 Series features a massive steel shackle guard that gives further protection against bolt cutters or saws but does not have the weather resistant shackle collars of the 6121 series.

Back View

D

Brand Net Ea.

MR A2000 MR 6270KA MR A2000T IX 2000SP

American, No Drill Holes................................. $ 22.80 Master, No Drill Holes...................................... 30.25 American with Drill Holes................................ 39.95 LAI with Drill Holes........................................... 43.50

No. 6321

Models 6121 & 6321 dimensions are: 2-1/8" wide. Shackle is 5/16" diameter. Shackle clearance is 1-1/8" vertical on 6121 series and 3/4" on 6321 series. Both series have 7/8" horizontal clearance. Available keyed alike or keyed different.

Key for 2000SP

Part No.

D

6121 Series is a more weather re­sis­tant lock but does not have the shackle guard fea­ture of the 6321 se­ries. D

Padlocks

No. 6121

Master Lock Padlocks that you have come to know and respect. Laminated steel construction resists rust and corrosion. Hardened steel shackles are standard. Ideal for conditions where sand, dirt or ice are a problem. All locks shown are available in either “keyed alike” or “keyed different” styles. Models 7KA & 7KALF have a 4-Pin tumbler. Base width is 1-1/8". Shackle diameter is 3/16". Vertical clearance on 7KA is 9/16" and 1-1/2" on 7KALF. Horizontal clearance is 1/2".

D

No. 7KALF 1-1/8"

Model 3 locks feature 4-pin tumbler.Base width is 1-1/2".Shackle diam­eter is .932". Vertical clearance is 3/4" on KA series and 2” on KALH series. Horizontal clearance is 5/8". Model 3KACOV locks are the same as Model 3 except Model 3KACOV features a weather-proof cover.

D

Part No.

Key Style

MR 6121KA MR 6321 MR 6321KA

Keyed Alike Keyed Different Keyed Alike

Net Ea

$ 17.85 23.40 23.95

Screw-Threaded Locks Screw Locks for coin meter doors. Available in either 4-5/8" length (inner shoulder to end of thread) to fit many standard coin drawers or in 8" length which can be cut down to fit special length needs. All locks are 5/8" thread size. Two key styles to choose from. Round MB1994 & MB1996 round key locks are standard in many coin meters throughout the country. An inexpensive, yet good security lock option. *Medeco 63W high security screw locks are virtually pick-proof. Special “angle-cut” keys are very difficult to duplicate giving additional security.

Model 1 locks fea­ture 4-pin tumbler. Base width is 1-3/4". Shackle diam­eter is 5/16". Vertical clearance is 15/16" on KA series and 2-1/2" on KALJ series. Horizontal clear­ance is 3/4".

4-5/8" or 8" 5/8" Thread

D

No. 1: 1-3/4"

D

MB1994

No. 5KA: 2" No. 3KACOV

Part-No.

D

D

Model 5KA locks feature 4-pin tumbler. Base width is 2". Shackle diameter is 3/8". Vertical clearance is 1", horizontal clearance is 15/16". Model 15 locks feature 5-pin tumbler. Base width is 2-1/2". Shackle diameter is 7/16". Vertical clearance is 1", horizontal clearance is 1-3/16". Part No. Base Width Key Style Net Ea MR 7KA 1-1/8" Keyed Alike................. $ 6.67 MR 7KALF 1-1/8" Keyed Alike *.............. 7.75 MR 3 1-1/2" Keyed Different............ 7.26 MR 3KA 1-1/2" Keyed Alike................. 7.92 MR 3KALH 1-1/2" Keyed Alike *............... 9.97 MR 3KACOV 1-1/2" Keyed Alike with cover. 9.61 MR 1 1-3/4" Keyed Different............ 8.37 MR 1KA 1-3/4" Keyed Alike................. 8.28 MR 1KALJ 1-3/4" Keyed Alike *............... 10.50 MR 81 1-3/4" Keyed Different............ 11.85 MR 81KA 1-3/4" Keyed Alike................. 12.40 MR 5KA 2" Keyed Alike................. 11.50 MR 15 2-1/2" Keyed Different............ CALL MR 15KA 2-1/2" Keyed Alike................. CALL * Features extra long shackles for added clearance. Note: Price add-on for special key numbers. OMAHA, NE (800)

228-9666

Stud Length

6-1/4"

63W-475

Net Ea.

IX MB1994 Round 4-5/8" $ 11.80 IX MB1996 Round 8" 11.80 IX 63W-475 Angle 4-1/2" 33.50 IX 63W-614 Angle 6-1/4" 31.95

Model 81 locks feature 5-pin tumbler for added security. Base width is 1-3/4". Shackle diameter is 5/16". Vertical clearance is 15/16", horizontal clearance is 3/4".

DULTMEIER SALES

Key Type

4-1/2" or

Cam Locks Cam Locks are designed for use on coin meter access doors or coin drawers. All locks are 5/8" thread size. This style of lock is available in three security levels. Model 9 locks are an inexpensive flat key lock used for upper meter doors where there is no access to money. Low security. Cam plates included. Model 8-55 locks are a round key lock that offers more security and is used for upper doors as well as coin drawers. Medium security. Cam plates included. *Model 60W Medeco, angle key locks feature a double locking design that is virtually pick-proof. Keys are also very difficult to duplicate without proper authorization. High security. Cam plates not included. No. 9 with cam D

D

D

8-55 with cam

60W less cam

Part-No.

Lock Style Net Ea.

JS 9 GW 8-55 IX 60W IX CTA08 IX CTH10

Flat Key................... $ 6.25 Round Key.............. 9.60 Angle Key................ 30.90 Flat Cam Plate Only.** .98 Off-Set Cam Plate Only** 1.20

** For 60W Series Locks. DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0148


Security Locks & Hasps • Wiper Bags

177

American Lock Padlocks

SAFETY LOCKOUTS for Controls and Valves

Solid Steel Padlocks from American Lock. Chrome-plated, case hardened construction with Boron shackles. 5-Pin tumbler is standard. (Keyed Alike). A5260 Series Square Padlocks are 2” wide x 3/4” thick. Shackle diameter is 3/8”. Horizontal shackle clearance is 3/4”. Vertical shackle clearance is either 1-1/8”, 2” or 3” as shown. A700 Series Round Padlocks are 2-1/2” wide x 1-1/8” thick. Shackle diameter is 7/16”. Horizontal shackle clearance is 15/16”. Vertical shackle clearance is 1-1/16”, or 2” as shown. Part No.

Width

Vert. Clearance

MR A5260 2” MR A5261 2” MR A5262 2” MR A700 2-1/2” MR A701 2-1/2”

1-1/8” 2” 3" 1-1/16” 2”

D

D

A5260

A700

A = Shackle Diameter B = Vertical Clearance C = Horizontal Clearance

Net Ea.

$ 19.00 21.00 21.30 24.95 25.50

Model 420 Safety Lockout for controls and valves. Helps guard against accidents, injury and equipment damage. Up to 6 workers can share a lockout. Cannot be opened until every worker has removed his lock. Double locking design prevents the lockout from being pried open when padlocks are in place. Meets OSHA standards for machine guarding. Made of vinyl coated, high tensile case hardened steel plated to prevent rust. Size is 4-3/8" long x 1-1/2" wide. 1" inside diameter when closed. Accepts shackles to 3/8".

D

D

Solid Brass Padlocks Brass Padlocks from Master Lock. Stylish and strong solid brass bodies. Standard with hardened steel shackles and 4-pin lock cylinders. Available in 3 different sizes. Keyed alike. Model 120KAD: Width is 3/4" • Shackle diameter is 5/32" • Vertical clearance is 7/16" • Horizontal clearance is 1/4". D

Model 140KAD: Width is 1-9/16" • Shackle diameter is 1/4" • Vertical clearance is 7/8" • Horizontal clearance is 13/16".

D

Model 150KAD: Width is 2" • Shackle diameter is 9/32" • Vertical clearance is 1" • Horizontal clearance is 1". Part No.

Width

Net Ea.

Padlock

Model 420 Safety Lockouts

* Model1220 Safety Lockout Kit Includes: (2) #420 Lockouts (6) #3 Padlocks with different colors (6) ID tags (6) Attachment Collars for ID tags

D

I.D. Tags

MR 120KAD 3/4" $ 3.33 MR 140KAD 1-9/16" 5.79 MR 150KAD 2" 8.87

Part No.

Net Ea.

MR 420 Safety Lockout $ 4.51 MR 1220 * Safety Lockout Kit 59.60

SECURITY HASPS

WIPER COVER BAGS

MASTER LOCK Security Hasps offer superior protection for doors, gates, cabinets, etc. Available in straight or hinged models. Hasps include all mounting hardware and screws. 720D

Great for Protecting Rear Wiper Blades During the Wash Process!

722D D

• WWB50 Bags are 3” Wide x 27” Long, 1.5 Mil • WWB75 Bags are 5” Wide x 27” Long, 1.5 Mil

D

D

HIGH SECURITY — SPECIAL APPLICATION 6-1/4" SINGLE HINGE HASP

Attachment Collars

• Sold in Rolls of 500 Bags

HIGH SECURITY — SPECIAL APPLICATION 7-3/4" DOUBLE HINGE HASP

Models 720D and 722D hinged hasps for corners and angles. Features heavy-gauge Hardened Steel to protect against cutting and sawing. Rolled edges to conceal mounting screws and prevent prying. Hinge pins are hidden and virtually impossible to remove.

Shown on Vehicle

5% Discount on 12 or More Rolls & 10% on 24 or More

D

Model 720D is a single hinged hasp, 6-1/4" long and accepts shackles to 7/16". Model 722D is a double hinged hasp, 7-3/4" long and accepts shackles to 7/16".

Part No.

Style

Length

Part No.

Net Ea.

DULTMEIER SALES

OMAHA, NE (800)

Net Ea.

DU WWB50 DU WWB75

MR 720D Hinged 6-1/4" $ 7.37 MR 722D Hinged 7-3/4" 8.42

228-9666

DAVENPORT, IA (800)

Wiper Bags, 3” Wide, Roll of 500 Wiper Bags, 5” Wide, Roll of 500

553-6975

www.dultmeier.com

$ 19.95 24.95 E0150


Coin Meter Decals 2-1/8" X 1-3/4" PRICE DECALS

For Coin Boxes

2-1/8" X 1-3/4" PRICE DECALS

Size is 2-1/8" x 1-3/4"

Price Decals for Coin Meters. Placement of these decals on coin meter maximizes customer attention to your messages. Weatherproof LEXAN coating with adhesive backing. Blue lettering on white background.

Please Order by Part Numbers Shown.

$1.00

$1.25

$1.50

$1.75

QUARTERS or DOLLARS

QUARTERS or DOLLARS

QUARTERS or DOLLARS

QUARTERS or DOLLARS

ND 2343

ND 2344

ND 2345

ND 2346

$2.00

$2.25

$1.00 $2.50

$2.75

QUARTERS or DOLLARS

QUARTERS or DOLLARS

QUARTERS QUARTERS or DOLLARS DOLLARS

QUARTERS or DOLLARS

ND 2347

ND 2348

ND 2349

ND 2350

$1.00

$1.25

$1.50

QUARTERS DOLLARS or TOKENS

QUARTERS DOLLARS or TOKENS

QUARTERS DOLLARS or TOKENS

ND 2351

ND 2352

ND 2353

ND 2354

$2.50

$2.75

$2.00 $1.00

$2.25

QUARTERS QUARTERS DOLLARS or or DOLLARS TOKENS

QUARTERS DOLLARS or TOKENS

QUARTERS DOLLARS or TOKENS

QUARTERS DOLLARS or TOKENS

ND 2355

ND 2356

ND 2357

ND 2358

25 ¢ quarters

50 ¢ quarters

75 ¢ quarters

$ 100

only

quarters only

NP 25D

NP 50D

NP 75D

NP 100D

$ 125

$ 150

$ 175

$ 2 00

NP 125D

NP 150D

NP 175D

NP 200D

$ 2 50

$ 3 00

NP 250D

NP 300D

only

quarters only

quarters only

only

quarters only

quarters only

quarters only

Adhesive Backed Price Decals: Weather-proof LEXAN coating with an adhesive backing. Size is 2-1/8" x 1-3/4". Blue letters on white background. Available in .25¢, .50¢, .75¢, $1.00, $1.25, $1.50, $1.75, $2.00, $2.50 and $3.00.

quarters only

$2.35 Each

$1.75

QUARTERS DOLLARS or TOKENS

178

2-1/8" X 1-3/4" PRICE DECALS 25¢

DEPOSIT SLOWLY

DEPOSIT SLOWLY

75¢

$1.00

ONE QUARTER

2 QUARTERS

3 QUARTERS

4 QUARTERS

ND 2300

ND 2302

ND 2303

ND 2304

$1.25

$1.50

$1.75

DEPOSIT SLOWLY

DEPOSIT SLOWLY

5 QUARTERS

6 QUARTERS

7 QUARTERS

8 QUARTERS

ND 2309

ND 2310

DEPOSIT SLOWLY

$2.35 Each

50¢

DEPOSIT SLOWLY

DEPOSIT SLOWLY

DEPOSIT SLOWLY

$2.00

INSTRUCTION DECALS For Coin Boxes Size: 2-1/8" x 1-3/4"

ND 2307

ND 2308

SUPER-VAC

SUPER-VAC

Instruction Decals for Coin Meters. Placement of these decals on coin meter maximizes customer attention to your messages.Weatherproof LEXAN coating with adhesive backing. Blue lettering on white background.

DEPOSIT

DEPOSIT

SLOWLY

SLOWLY

2 QUARTERS

3 QUARTERS

TROUBLE

ND 2313

ND 2314

THIS EQUIPMENT IS USUALLY TROUBLE FREE. IF YOU LOSE MONEY, WE WILL REFUND IT. PLEASE LEAVE YOUR PHONE NUMBER IN BOX AT FRONT OF BUILDING.

DEPOSIT

DEPOSIT

.75¢

$1.00

SLOWLY

SLOWLY

SLOWLY

QUARTERS or TOKENS

QUARTERS or TOKENS

QUARTERS or TOKENS

ND 2334

ND 2332

ND 2306

$1.25

$1.50

$1.75

SLOWLY

SLOWLY

SLOWLY

QUARTERS or TOKENS

QUARTERS or TOKENS

QUARTERS or TOKENS

ND 2333

ND 2336

ND 2337

$2.00

$2.25

$2.50

SLOWLY

SLOWLY

SLOWLY

QUARTERS or TOKENS

QUARTERS or TOKENS

QUARTERS or TOKENS

ND 2338

ND 2339

ND 2340

DEPOSIT UP TO 15 QUARTERS FOR EXTENDED TIME

LOCATED AT FRONT OF BUILDING

ND 2311

ND 2324

ND 2326

NOTICE NO MONEY IN THIS BOX

NOTICE COIN VAULT EMPTIED DAILY

WE WANT TO KNOW COMPLAINTS OR SUGGESTIONS

ND 2327

ND 2329

ND 2330

MONEY REMOVED DAILY

BILL CHANGER

THANKS!

IF YOU HAVE ANY PROBLEMS, ABOUT THIS CAR WASH AND TELEPHONE # IN MAIL BOX ON EQUIPMENT ROOM DOOR

DEPOSIT

Please Order by Part Numbers Shown. ND 2331 •

www.dultmeier.com

$2.35 Each Lexan Price Decals with adhesive backing. Ideal for bay meters or vacuums. 2-1/8" x 1-3/4". Blue letters on white background. Please Order by Part Numbers Shown.

DEPOSIT

DEPOSIT

PLEASE LEAVE NAME, ADDRESS

(800) 228-9666

75¢

.50¢

$2.35 Each

DULTMEIER SALES • OMAHA, NE

50¢

DEPOSIT

• DAVENPORT, IA

(800) 553-6975

DEPOSIT

DEPOSIT

DEPOSIT

E0155


Safety & Information Signs - 12"x12"

179

ALUMINUM/LEXAN SAFETY & INFORMATION SIGNS 12" x 12"

Weather-proof “Lexan” coating with .032" aluminum backing. Tough, chemical resistant construction. Eye-catching Blue letters on White background. Size is 12" x 12". Please Order by Part Numbers Shown.

ND 12200

ND 12207

ND 12208

ND 12209

ND 12211

ND 12215

ND 12216

ND 12217

ND 12221

ND 12223

CLEARCOAT PROTECTANT!! APPLY TO ENTIRE VEHICLE AND THEN RINSE THOROUGHLY. ND 12226

ND 12229

ND 12240

ND 12305

ND 12275

$ 18.95 Each LARGE BAY SIGNS 23-1/2" X 15-1/2" Heavy-Duty Lexan on .032 Aluminum sheet

No. 307

No. 304 No. 306

EXIT ONLY No. 311

Part No. ND 304 ND 306 ND 307 ND 311 ND 316

Message Color Material Net Ea. “Spot Free Rinse”...................... Blue/White Aluminum $ 39.95 “NO In This Bay”....................... Blue/White Aluminum 39.95 “During Busy Hours”................. Blue/White Aluminum 39.95 “Stop-Exit Only” ....................... Red/White Aluminum 39.95 “All New Spot Free Rinse” ....... Blue/White Aluminum 39.95

15% Discount on 3+ Assorted

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

25% Discount on 7+ Assorted

www.dultmeier.com

• DAVENPORT, IA

No. 316

(800) 553-6975

E0153


Signs & Decals

180

LEXAN BAY PRICE SIGNS 12" x 12"

Weather-proof “Lexan” coating with .032" aluminum backing. Tough, chemical resistant construction. Eye-catching Blue letters on White background. Size is 12" x 12". Please Order by Part Numbers Shown.

$1.25 DEPOSIT QUARTERS OR DOLLAR COINS

$1.50

$1.75

DEPOSIT QUARTERS OR DOLLAR COINS

DEPOSIT QUARTERS OR DOLLAR COINS

ND 12307

ND 12308

$2.00

$2.25

DEPOSIT QUARTERS OR DOLLAR COINS

DEPOSIT QUARTERS OR DOLLAR COINS

ND 12310

ND 12311

$1.25

$1.50

DEPOSIT QUARTERS DOLLAR COINS OR TOKENS

DEPOSIT QUARTERS OR DOLLAR COINS

SLOWLY

2-1/4”

QUARTERS ND 12205

$1.25

$1.50

$1.75

DEPOSIT

DEPOSIT

DEPOSIT

SLOWLY

SLOWLY

SLOWLY

6

QUARTERS

7

QUARTERS ND 12246

QUARTERS ND 12247

$2.00

$2.50

DEPOSIT

DEPOSIT

DEPOSIT

SLOWLY

SLOWLY

SLOWLY

10 QUARTERS

12 QUARTERS

ND 12319

ND 12320

QUARTERS ND 12248

$2.50

$3.00

$ 18.95 Each

DEPOSIT QUARTERS DOLLAR COINS OR TOKENS

Less 10% on 15+ Assorted

ND 12318

Vacuum Decals

DROP COIN DECALS

4” x 3” Vacuum decals, vinyl with adhesive backing. Yellow letters on black background.

QUARTERS ONLY

1-3/4”

4

QUARTERS ND 12204

8

ND 12315

$1.00

ND 12203

ND 12243

DEPOSIT QUARTERS DOLLAR COINS OR TOKENS

ND 12317

3

QUARTERS

5

$1.75

DEPOSIT QUARTERS DOLLAR COINS OR TOKENS

ND 12316

SLOWLY

ND 12312

$2.25

DEPOSIT QUARTERS DOLLAR COINS OR TOKENS

DEPOSIT

SLOWLY

2

$2.50

ND 12314

$2.00

75¢ DEPOSIT

ND 12309

DEPOSIT QUARTERS DOLLAR COINS OR TOKENS

ND 12313

50¢ DEPOSIT

Quarters Only

4-1/2”

AA 8429-1

AA 8429-3

AA 8429-4

AA 8429-5

Coin Return COIN RETURN NP D902A

NP DC903A

“Lexan” with adhesive backing.

1-3/4”

D902A is 2-1/4" x 1-3/4" and is for short-drop coin mechanisms. DC903A is 4-1/2" x 1-3/16" and is for long-drop coin mechanisms. Part No. Part No.

Net Ea.

NP D902A NP DC903A

$ 1.10 2.90

Short-Drop Decal Long-Drop Decal

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

AA 8429-1 AA 8429-3 AA 8429-4 AA 8429-5

www.dultmeier.com

Net Ea.

“Hang Hose Here” Decal... $ 1.90 “Vacuum 50¢” Decal.......... 2.15 “Vacuum 75¢” Decal.......... 1.90 “Vacuum $1.00” Decal....... 2.30

• DAVENPORT, IA

(800) 553-6975

E0154


Decals • Bay Signs

181

LEXAN ROTARY SWITCH DECALS LEXAN coated decals with adhesive backing for rotary switch instruc­tions. De­signed with colorful 3/4" in­serts that show the functions pro­moted in your car wash. Simply fill in the func­tions and leave other openings blank.

PRESOAK

OFF

ENGINE CLEANER

TIRE CLEANER

BAY INSTRUCTION SIGN

WASH/ SOAP

BAY INSTRUCTION SIGN: Now you only need one bay sign to instruct your customers in all of your bay functions. Brightly colored “LEXAN” instruction strips with permanent adhesive for great vi­ sual appeal. Strips are 3” x 22”. Sign base is 24” x 40” screen printed .040 Aluminum and will hold up to 10 instruction strips. Sign base is blue with white letters. Simply order the necessary decals to match your particular wash functions.

D

RINSE

FOAM BRUSH

WAX

909 is a 8-position base decal and is 3-1/4" x 3-1/4". 915 is a 10-position base NP 915 Base Decal, 10 Position

decal and is 4-1/4" x 4-1/4"

Inserts for both are individual colors to differentiate from each other. Colors match to Bay Instructional Sign (shown at right).

925L is 3-1/4" x 3-1/4" and the 930L is 4-1/4" x 4-1/4" are clear, adhesivebacked, Lexan cover to protect decals and inserts. Part No. Net Ea. NP 909 Base Decal, 8 Pos. $ 1.35 NP 915 Base Decal, 10 Pos. 4.65 NP 925L Clear Overlay for 909 1.19 NP 930L Clear Overlay for 915 1.55 NP 909A1-B Brush Insert........... .59 NP 909A1-BG Bug Off Insert........ .98 NP 909A1-D Dryer Insert............ .98 NP 909A1-E Engine Insert......... .98 NP 909A1-F Spot-Free Insert..... .59 NP 909A1-O Off Insert................ .59

Part No. NP 909A1-P NP 909A1-R NP 909A1-S NP 909A1-T NP 909A1-W NP 909A1-X NP 909A1-C NP 909A1-TFB NP 909A1-TFW

Net Ea. Pre-Soak Insert. $ .59 Rinse Insert............ .59 Soap Insert............. .59 Tire Insert............... .59 Wax Insert.............. .59 Tire/Engine Insert... .59 Clear Coat Insert.... .98 Triple Foam Brush.. .98 Triple Foam Wax..... .98

dultmeier.com

Note: Main Function Headings are spelled out in English above and in Spanish below.

ND 120B Blue Base Sign with Function Decals Added

Part No.

INDIVIDUAL FUNCTION DECALS READ AS FOLLOWS:

ND 100

(PRE-SOAK): Turn to Pre-Soak, apply to entire car before proceeding to high pressure wash.

ND 101

(OFF): Turn to OFF, return gun to holder. Proceed to Detail Area.

ND 102

(SPOT FREE RINSE): Turn to Spot Free Rinse and rinse entire car at low pressure, pure water, for spot free rinse.

ND 103

(WAX): Grip spray gun firmly. Turn to Wax, pull trigger to wax car. Turn to Rinse to spread wax evenly.

ND 104

(RINSE): Grip spray gun firmly. Turn to Rinse, pull trigger to rinse entire car.

ND 105

(FOAM BRUSH): Check foam brush for cleanliness. Turn to Foam Brush and brush thoroughly. Return brush to holder.

ND 106

(TIRE CLEANER): Turn selector knob to Tire Cleaner. Pull trigger to foam tires. For best results, apply to dry surface. Rinse.

ND 107

(WASH / SOAP): Grip spray gun firmly. Turn to Wash / Soap, pull trigger, w ash entire car. Rinse. Return spray gun to holder.

ND 109

(WHITEWALL / DEGREASER): Turn selector knob to Whitewall & Degreaser. Wash entire engine or tires, let soak and rinse off.

ND 110

(ENGINE CLEANER): Turn selector knob to Engine Cleaner. Wash entire engine, let soak and rinse off.

ND 111

(CLEAR COAT WAX): Apply Clear Coat Protectant Wax to all painted surfaces. Rinse entire vehicle thoroughly.

ND 112 (TRIPLE FOAM BRUSH): Check foam brush for cleanliness. Turn to Triple Foam Brush. Brush vehicle surface with multi-color foam. Return foam brush to holder. Rinse. ND 113

(TRIPLE FOAM WAX): Grip small spray wand. Turn switch to Triple Foam Wax. Cover vehicle surface with multi-color foam. Return wand to holder. Rinse with high pressure water.

• Large Inventories of Over 3 Million Total Items!

ND 117

(BUG CLEANER): Turn selector knob to Bug Cleaner. Spray windshield and bumpers, allow to soak. Rinse with high pressure water.

• View Current Pricing!

ND 119

(BLOWER / DRYER): Turn selector knob to Dryer. Use nozzle to Air Dry entire vehicle.

• Shop and Order On-Line 24 Hours a Day, 7 Days a Week!

• Web Specials and Bargain Corner! • Hundreds of Parts List Schematics (and more to come!)

Part No. Net Ea. ND 120B * Blue Base Sign, 10-Position . $ 56.95 ND --- Function Decals, Specify......... CALL

• Technical Library packed with information!

* 10% Discount on 3+

• Know Your Part Numbers? Use the Web Quick Order Page!

*20% Discount on 10+

• See New Items not Shown in Our Printed Catalogs! • Track Your Order Status and History!

Visit Our Web Site at

• Secure Site for Safe On-Line Ordering.

http://www.dultmeier.com or E-Mail us at dultmeier@dultmeier.com

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0152


TurtleWax SIGNAGE

182

®

143

BAY SIGNS 23" X 16" Standard Size

TU SS3

TU SS5

TU SS1

TU SS4

TU SS7

$ 45.95 Each

Less 10% on 3+ Assorted Less 15% on 10+ Assorted

TU SS6

MENU SIGNS & PUMP TOPPERS Part No.

Description

Net Ea.

TU SS9 Menu Sign ONLY............. $ 74.10 TU ---- Menu Strips ..................... 6.96 TU HSPT Pump Topper.................... CALL

TU SS2

TU SS9 23" X 42" MENU SIGNS

TU SS8

TU HSPT 12" X 20" PUMP TOPPERS

WindMaster Curb Sign Holders

D D

4005SRC 15WM-BK

Part No. Wt. Net Ea. TS 15WM WindMaster Sign, Silver with Rigid Base 31 lbs. $ 139.50 TS 15WM-BK WindMaster Sign, Black with Rigid Base. 31 lbs. 139.50 TS 4005SRC WindMaster Sign with Rolling Base........ 42 lbs. 205.00 TS BP2844 Protective Overlay, 28" x 44"................... 1 lbs. 14.95

15WM

Your Advertising Here! DULTMEIER SALES • OMAHA, NE

(800) 228-9666

Ideal way to promote special advertising or name brand products. Withstands wind velocities up to 75 MPH. Designed for maximum rust resistance. PosterGrip frame sets up quickly for ease in changing displays if required. Insert size is 28" W x 44" H. Visual dimensions are 25-1/2" x 41-1/2". Clear plastic overlays are available for added protection of your insert. Can be shipped UPS.

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0663


Sign Holders & Outdoor Frames

183

144

Outdoor Sign Holders Windmaster Curb Sign Holders are an ideal way to promote and advertise on your lot or property. Designed to handle wind velocities up to 75 mph. Messages can be displayed on both sides. Heavy duty aluminum frame is available in Black or Silver. Powder coated, black steel base is standard. Postergrip design holds posters firm, evenly and wrinkle-free. Clear protective overlays are also available for added protection of your advertising. Two Sizes: 28” x 44” with 25-1/2” x 41-1/2” visual opening or 41” x 55” with 38-1/2” x 52-1/2” visual opening.

D

15WM

Your Advertising Here! Part No. TS 15WM Silver Windmaster Sign, 28” x 44”.......... TS 15WM-BK Black Windmaster Sign , 28” x 44”........ TS 20WM Silver Windmaster Sign, 41” x 55”.......... TS 20WM-BK Black Windmaster Sign, 41” x 55”.......... TS BP2844 Clear Protective Overlay, 28" x 44"......... TS BP4155 Clear Protective Overlay, 41” x 55”.........

D

15WM-BK

Wt. Net Ea. 31 lbs. $ 139.50 31 lbs. 139.50 47 lbs. 263.00 47 lbs. 263.00 1 lb. 14.95 1 lb. 30.95

Outdoor Rolling Sign Holders Windmaster Plus Rolling Sign Holders. Same heavy duty design and wind performance as the units above but with a tip and roll base. Easy to move from location to location or when operations are closed. Base is weather and impact resistant, gray polyethylene and can be filled up to 7 gallons of water, sand or anti-freeze ballast. Base dimensions are 6-1/2” H x 25” W x 26” D. Aluminum poster frames are 28” x 44” in black or silver. D

4005SRC

Part No. TS 4005SRC Windmaster Plus with Rolling base, Silver frame TS 4005BKA Windmaster Plus with Rolling base, Black frame TS BP2844 Clear Protective Overlay, 28" x 44"......................

PosterGrip® Outdoor Frames

Wall Poster Frames Outdoor or Indoor An ideal way to promote and advertise in bays or on building exteriors. These frames can even be used on round or square poles. Heavy duty, aluminum construction features PosterGrip® design for holding posters even, firm and wrinkle-free. Mounting holes allow for vertical or horizontal mounting. Sizes are 22” x 28” or 28” x 44”. Available in black or silver. Clear protective overlays are available for added protection of your advertising.

Designed to withstand outdoor elements

Attach frames to round or square poles up to 9-1/2” in diameter & 30” in circumference.

D

Model 825

(800) 228-9666

Net Ea. $ 205.00 205.00 14.95

Mounting Brackets

Part No. Wt. Net Ea. TS 820B Black PosterGrip® Wall Frame, 22” x 28”.... 7 lbs. $ 59.95 TS 820S Silver PosterGrip® Wall Frame, 22” x 28”... 7 lbs. 59.95 TS 825B Black PosterGrip® Wall Frame, 28” x 44”.... 11 lbs. 79.95 TS 825S Silver PosterGrip® Wall Frame, 28” x 44”... 11 lbs. 79.95 TS 898SG Single Pole Bracket...................................... 2 lbs. 13.50 TS 899DB Double Pole Bracket.................................... 2 lbs. 16.85 TS BP2228 Clear Protective Overlay, 22" x 28".............. 1 lb. 9.75 TS BP2844 Clear Protective Overlay, 28" x 44".............. 1 lb. 14.95

DULTMEIER SALES • OMAHA, NE

Wt. 42 lbs. 42 lbs. 1 lb.

www.dultmeier.com

D

• DAVENPORT, IA

Single Frame: Model 898SG (2) Frames (back-to-back) Model 899DB

(800) 553-6975

E0769


Weep System • Thermostat • Water Testers Automatic Cycle Weep System For Freeze Protection

184

Handheld Water Testers

• Eliminate customer “Washing” with weep water • Reduce total weep water usage • Save on water and sewer bills • Use as a System Thermostat

for control of other equipment

• Acts as Weep System Thermostat “Weep Mizer” Automatic Cycle Weep System. Designed to “Cycle” your weep water: On for an adjustable amount of time and then off for an adjustable amount of time.

D

Standard Features Include: Accurate to + or - 1/2 ° F. Operating range from -20 to +112 ° F. • Designed with battery backup to eliminate the need to re-program if there is a power failure • One unit will handle all bays for all necessary weep requirements • Continuous display of outside temperature on display board • Acts as a secondary thermostat for control of floor heat boiler, pump room heater, etc. • Manual override of automatic operation if other on-off weep periods are required • Maintains memory of “on-time”, “weep time saved”, high temperature and low temperature recorded for the day • Unit can be easily re-programmed with two push buttons • Requires only 120 Volt AC for operation • Used with a Normally Open Solenoid (not included) to control weep water supply. “Weep Mizer” System

$ 375.00

COM100

TDS4

PH200

PH200: This handheld tester measures PH and Temperature. Digital readout with waterproof housing. Auto-off, data hold, low battery indicator, batteries and buffer solution are standard features. Range is 0-14 PH and 0° to 80° C. (32° to 150° F.) COM100: This highly accurate handheld tester measures TDS,Temperature and Conductivity. Digital readout with waterproof housing. Auto-off, data hold and low battery indicator and batteries are standard features. Accurate to + or - 2%. TDS range from 0-8560 ppm and temperature 0° to 80° C. (32° - 150° F.)

Part No.

Thermostats For remote control of Weep or Floor Heat Systems designed for freeze prevention. Standard with a capillary tube so that the unit can be mounted in the pump room and the bulb can be located in an outside area. Temperature differential is + or - (1) degree F. on the Model T675A-1011 and + or - (4.5) degrees F. on the Model 2E399.

D

TDS4: Handheld TDS Tester. Economical yet accurate to + or - 2%. Range is 0-9990 ppm. Easy-to-read, digital display.

Part No. Net Ea.

DX DX1000

D

D

Unit adjusts the “on weep” “off-weep” periods for a rise or fall in temperature. (i.e.Weep is on for 6 seconds and off for 54 seconds when the temperature falls below 35° F. Weep is on continuously if temperature falls below 15° F.) Unit can be easily recalibrated for other on-off time periods if climate dictates.

Measures

Net Ea.

HM PH200 PH/Temperature........................ $ 75.10 HM COM100 TDS/Temperature/Conductivity.. 54.05 HM TDS4 TDS........................................... 24.00

T675A-1011 2E399

Water Test Kits Testing kits for water hardness, ni­trates/ nitrites, alkalinity and pH analysis. Designed for quick checks on the quality of water supplies or the ef­ficiency of water soft­eners, spot-free sys­tems, etc.

D D

For Weep Systems use these units with a “normally open” solenoid (not included) to activate the weep water at desired outside temperature. (T675A-1029 is a Slabstat thermostat for use in floor heat installations).

5B is a Hardness test kit and features a “Liquid Drop Count Titration” method of analysis.

D

D

5B

TEMPERATURE Part No. DIFFERENTIAL TUBE RANGE Net Ea. HU T675A-1011 + or - (1) Degree 5' 0 to 100° F. $ 128.50 GN 2E399 + or - (4.5) Degrees 8' -30 to 90° F. 82.95 HU T675A-1029 + or - (3) Degrees * 20’ 0 to 100° F. 121.50 * Slabstat for Floor Heat

26013-00 is a pH test kit and features paper strips for analysis. (100 strips per kit).

Custom Decals

27450-50 is a Chlorine test kit and features paper strips for analysis. (50 strips per kit).

We Can Create Custom Decals for Your Coin Meters & Equipment Using Your Company’s Logo

27452-50 is a hardness test kit and features paper strips for analysis. (50 strips per kit). 2745425 is a Nitrate/Nitrite test kit and features paper strips for analysis. (25 tests per kit).

Part No.

HJ 5B HJ 26013-00 HJ 27450-50 HJ 27452-50 HJ 2745425

Call Us For Details and Specifications! DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

D

Net Ea.

Water Hardness Test Kit, liquid.. $ 26.50 pH Test Kit, strips....................... 31.95 Chlorine Test Kit, Strips............. 23.95 Hardness Test Kit, strips............ 17.55 Nitrate Test Kit, strips................. 28.95

• DAVENPORT, IA

(800) 553-6975

E0018


Thermometers & Thermostats

185

“Minitemp” Series

Hot Water Thermostats

Indicates Surface Temperature Just Point, Shoot & Read the Temperature on the Large Backlit Display

Thermostats for controlling water temperature on hot water pressure washer machines. Panel mount or flow-through designs.

Infrared Thermometer

GPT Models feature dual scales for Fahrenheit and Celsius, designed to be panel mounted. Rated to 4000 PSI. Standard with 60" capillary tube and copper immersion bulb. Rated to 16 amp, 380 volt. Accuracy to ±5%.

Some Typical Applications: • AUTOMOTIVE: Troubleshoot engines including cooling sensors, thermostats, radiators, brakes, tires, ignition systems, etc. • ELECTRICAL: Check electrical panels for “hot” spots, motors & bearings. • HVAC: Monitor supply & return registers, furnace performance, duct work & window insulation; Balance room temperatures & perform energy audits. • PAVEMENTS & FLOOR HEAT SYSTEMS: Check pavement temperatures and floor heat system effectiveness. Features: Pocket sized, light & easy to use • Fast, rugged, reliable & accurate • 0˚ F to 500˚F range • C˚/F˚ Selectable • 9 Volt battery • Economical • Low battery indicator • 3 digit backlight display • 7 second hold. D

D

GPT3090 & GPT30150

Model 00818 has a flow through design. Rated to 10 GPM and 4000 PSI. Rated to 120 Volt - 10 Amp or 230 Volt - 5 Amp. 1/2” Ports.

D

Spot Size Part No. Description @ 5’ Net Ea. RA RAYMT4U IR Minitemp Thermometer (with Laser)....... 10” $ 99.70

00818 100272 D

Non-Contact

Model 100272 is flow through design rated to 35 gpm and 5000 PSI. (2) 1/2" FPT ports. Rated to 200° F. Electric load rating is 120 volts @ 10 amps.

Infrared Thermometer Indicates Surface Temperatures

Part No.

Has hundreds of uses. Can be used to check/diagnose engines, cooling/heating systems, motors, bearings, electrical panels and any other item where temperature is important. Also used to check pavement temperatures, floor heat system effectiveness, etc.

IP GPT3090 IP GPT30150 WT 00818 IP 100272

Features: Lightweight, compact & easy to use • Fast, rugged, reliable & accurate • -25˚ F. to +999˚ F. range • 3 digit backlit display & C˚/F˚ selectable • Laser sighting with high distance to spot ratios • Simple batteries.

Thermostat Thermostat Thermostat Thermostat

Temperature Rating

86° F. to 194° F. 86° F. to 320° F. 50° F. to 300° F. Ambient to 200° F.

Net Ea.

$ 30.50 30.50 45.00 130.50

Surface Mount Thermometer Provides for quick measurement of temperatures of boilers, air ducts, motors, bearings, plumbing lines, etc. Magnetic design allows for easy mounting to any ferrous surface. 2" dual scale measures 0° F. to 250° F. and -20° C. to +120° C.

Spot Size Part No. Description @ 5’ Net Ea. RA ST20 IR Thermometer with Laser & Case 5” $ 515.00

Thermometers Ridgid Weld

Back Mount

D

Adjustable Hinge

LN250

Industrial thermometers for checking temperatures in tanks, plumbing lines, vessels, etc. 304 Stainless Steel welded construction for corrosion resistance to most chemicals. Rustproof, dustproof, leakproof. Extra heavy glass lens.

D D

BC350R

Part No.

Part No.

Temperature Dial MPT Mount Range: Face Port Type

ST J701 ST LN250 ST LN256 ST BC350R ST B1B5H

-40° - 160° F. 0° - 250° F. 50° - 400° F. 0° - 220° F. 0° - 220° F.

2" 3" 3" 5" 1"

DULTMEIER SALES

Stem

OMAHA, NE (800)

SERVICE & REPAIRS Did you know? We can service almost every brand of pump we sell in our catalog.

Net Ea.

1/4" Back 6" $ 23.25 1/2" Back 2-1/2" 23.05 1/2" Back 2-1/2" 23.05 1/2" Adjustable 2-1/2" 57.95 - Back 5" 4.78

228-9666

Net Ea.

DR ST250 Surface Thermometer $ 37.15

Available in either back mount or adjustable styles (back or bottom). Mounting ports are MPT. Many other stem lengths are available if required. Stem diameter is 1/4". Model B1B5H Pocket Thermometer is designed B1B5H for easy spot checks of temperatures. 1" dial face with 5" probe. Comes with handy D pocket case. Range is 0˚ to 220˚ F. Stainless construction.

Call us at 1-800-228-9666 (Omaha, NE) for a quote! DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0081


Plastic Strainers In-Line Strainers

Dia.

(Plastic)

Compact "T" style line strainers with large filter areas for better filtration of liquids. Strainer elements can be easily cleaned or replaced without removing the entire strainer from the system. Tops and bowls feature heavy buttress threads to prevent cross-threading. Rated to 150 psi at 70° F. or 100 psi at 125° F. Note: Do not use these strainers in systems where pressure spikes in excess of maximum operating pressure can be expected. All strainers are standard with 304SS wire mesh screens in 50 or 80 mesh sizes. 80 Mesh is 178 micron rating. Sealing gaskets are Viton® on all models. Upper strainer caps are White Nylon construction. All strainer bowls are available in (white-nylon) or (clear-polymide). Both strainer types work well with soaps and waxes. (Specific compatibility should be checked for all chemical uses). All strainers are standard with female pipe threads except for 3350-82F "mini-strainer" which has 1/2" MPT x 1/4" FPT ports. 3350-44N

186

H

End Line Strainers D

104 Series & Series 3350-21/22

End Line Suction Strainers are ideal for water supply or chemical lines. Protects pumps and injectors from sediment or foreign particles. For tanks, tubing or hose. Pushes over tubing or hose. Sizes shown.

Designed with female hose inlet so that tubing, hose or hose barbs can be directly installed. 40 or 50 mesh stainless screens are standard. Bodies are plastic. 3350-32 & 69 are 7" long and feature 80 mesh plastic screens. Available with hose barb or pipe thread inlet. Bodies are Nylon. Larger screen surface for better filtering.

D

3350-44P Clear Bowl

3350-69 & 3350-32

3800-35 is an in-line garden hose gasket/strainer. PVC construction, stainless steel screen.

3800-35

Length/ Part No. Inlet Diameter Height Mesh Net Ea. HY 3350-22 1/8” FPT 1" 3/4" 50 $ 2.73 HY 3350-21 1/8” FPT 1-1/4" 1" 50 3.03 TW 10406 1/4" FPT 1-1/2" 1-1/8" 40 4.18 TW 10416 3/8" FPT 1-1/2" 1-1/4" 40 4.83 TW 10421 1/2" FPT 1-3/4" 1-1/2" 40 5.82 HY 3350-33 3/4” FPT 2" 1-1/2" 40 4.02 TW 10446 1" FPT 3" 2-1/4" 40 9.74 TW 10442 1” FPT 3” 2-1/2” 20 9.76 TW 10464 1-1/2" FPT 3" 2-1/2" 40 11.30 HY 3350-32 3/4" M Hose Barb 1-1/4" 7" 50 10.25 HY 3350-69 3/4" MPT 1-1/4" 7" 50 10.10 HY 3800-35 Garden Hose Strainer 5/8" 1/2" 50 .33

D

3350-82F

D D

Part No. HY 3350-82F HY 3350-42N HY 3350-42P HY 3350-68N HY 3350-68P HY 3350-44N HY 3350-44P HY 3350-45N HY 3350-45P HY 3350-61N HY 3350-61P HY 3350-62N HY 3350-62P HY 3350-75N HY 3350-75P HY 3350-116N HY 3350-116P

Ports Bowl Screen 1/2" MPT Clear 80-Mesh 1/2" FPT White 50-Mesh 1/2" FPT Clear 50-Mesh 1/2" FPT White 80-Mesh 1/2" FPT Clear 80-Mesh 3/4" FPT White 50-Mesh 3/4" FPT Clear 50-Mesh 3/4" FPT White 80-Mesh 3/4" FPT Clear 80-Mesh 1" FPT White 50-Mesh 1" FPT Clear 50-Mesh 1" FPT White 80-Mesh 1" FPT Clear 80-Mesh 1-1/4" FPT White 50-Mesh 1-1/4" FPT Clear 50-Mesh 1-1/2" FPT White 50-Mesh 1-1/2" FPT Clear 50-Mesh Less 10% on 12 Assorted

Y-Type Line Strainers

Net Ea. $ 8.76 13.00 18.55 14.65 16.85 13.15 19.05 14.95 20.85 20.55 28.00 23.10 30.40 23.55 35.65 25.95 37.90

(Plastic Construction)

D

CAP

STRAINER REPAIR PARTS

BOWL GASKET

REPAIR PARTS

SCREEN

Corrosion-Free PLASTIC BODY and 50-Mesh or 100-Mesh Stainless Steel SCREEN for use with water and other fluids corrosive to brass or steel. Screen is easily removed for quick cleaning. Maximum Operating Pressure is 125 PSI. Maximum Temperature Rating is 120° F.

Part No. Size Description Net Ea. HY 3351-7 1/2” Strainer Cap....................... $ 6.20 HY 3351-6 3/4” Strainer Cap....................... 7.74 HY 3351-14 1” Strainer Cap....................... 13.20 HY 3351-16 1-1/4” Strainer Cap....................... 15.65 HY 3351-26 1-1/2” Strainer Cap....................... 17.40 HY 3351-5 3/4” * Strainer Bowl, White Bowl 4.53 HY 3351-15 3/4” * Strainer Bowl, Clear Bowl 13.00 HY 3351-13 1”, 1-1/4”, 1-1/2” * Strainer Bowl, White Bowl 9.85 HY 3351-24 1”, 1-1/4”, 1-1/2” * Strainer Bowl, Clear Bowl 24.45 HY 1700-44 1/2" & 3/4" Buna Gasket...................... .67 HY 1700-45 1/2" & 3/4" Viton® Gasket.................... 5.08 HY 1700-57 1", 1-1/4”, 1-1/2” Buna Gasket...................... .92 HY 1700-58 1", 1-1/4”, 1-1/2” Viton® Gasket.................... 6.72 HY 3800-29 1/2" & 3/4" 20-mesh Stainless Screen. 5.53 HY 3800-25 1/2" & 3/4" 50-mesh Stainless Screen. 4.62 HY 3800-26 1/2" & 3/4" 80-mesh Stainless Screen. 7.40 HY 3800-40 1" 20-mesh Stainless Screen. 6.89 HY 3800-41 1" 50-mesh Stainless Screen. 6.89 HY 3800-42 1" 80-mesh Stainless Screen. 11.60 HY 3800-43 1-1/4" 20-mesh Stainless Screen. 6.93 HY 3800-44 1-1/4" 50-mesh Stainless Screen. 6.86 HY 3800-45 1-1/4" 80-mesh Stainless Screen. 13.20 HY 3800-65 1-1/2" 20-mesh Stainless Screen. 11.45 HY 3800-66 1-1/2" 50-mesh Stainless Screen. 10.00 HY 3800-67 1-1/2" 80-mesh Stainless Screen. 16.20 * NOTE: Nylon Bowls are alright for alcohol fuels, not for acids. Polymide Bowls are alright for acids, not for alcohol fuels. Clear Bowls are available in either.

Part No. Ports

Screen

Net Ea.

DE S2P DE S3P IP FY34 IP FY10

100-M 100-M 50-M 50-M

$ 6.73 6.73 19.90 19.90

Line Strainer........ 1/4" FPT Line Strainer........ 3/8" FPT Line Strainer........ 3/4" FPT Line Strainer........ 1" FPT

Self-Cleaning Line Strainers The TeeJet Self Cleaning Strainer extends your spraying time with a selfcleaning feature that minimizes clogging. The tapered inner cylinder inside the entire length of the screen provides a gap between the screen face and the cylinder. This gap causes the inlet fluid to flow at a high velocity past the screen face providing for a continuous wash down of particles to the bypass line. D

AA126 strainers are made of glass filled polypropylene and are available in 3/4”, 1”, 1-1/4” and 1-1/2” as well as 50 and 75 series flange connection. They use a 304 stainless steel strainer element: No. CP12285 for 3/4” & 1”; CP12290 for 1-1/4” and 1-1/2”. Part No. Size Screen GPM Net Ea. SS AA126MLSC350 3/4” 50 23 $ 27.75 SS AA126MLSC450 1” 50 35 27.75 SS AA126MLSC530 1-1/4” 30 59 46.50 SS AA126MLSC6100 1-1/2” 100 77 46.60 SS AA126MLSC650 1-1/2” 50 77 46.60 Note: Screens are available in 16, 30, 50, 80 and 100 Mesh

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0094


Plastic Strainers

187

STRAINERS Spraying Systems Strainers are available in a wide variety of materials and screens. Heads are made of polypropylene cast iron. Bowls are constructed of polypropylene and nylon. Features: Stainless Steel Screens with color-coded polypropylene frames • Maximum Temperatures up to 100° F. • EPDM Gasket on polypropylene heads • Buna on 1-1/4" to 2" sizes. Note: 126ML strainers have a removable cap for flush-out operations. 200 PSI, 70° F. — Note: Specify Screen Size if Other than Shown —

122-1/2PP 1/2” & 3/4” Poly

AA126ML Threaded Poly

D

D D

Part No. Size Description PSI Mesh GPM SS 122-1/2PP 1/2" Strainer, Poly Head & Bowl 150 50 12 SS 122-3/4PP 3/4" Strainer, Poly Head & Bowl 150 50 16 SS AA126ML-350 3/4” Strainer, Poly Head & Bowl 200 50 23 SS AA126ML-430 1” Strainer, Poly Head & Bowl 200 30 35 SS AA126ML-F5050 *1” Flanged Strainer, Poly Head & Bowl 200 50 35 SS AA126ML-F5080 *1” Flanged Strainer, Poly Head & Bowl 200 80 35 SS AA126ML-530 1-1/4” Strainer, Poly Head & Bowl 200 30 59 SS AA126ML-630 1-1/2” Strainer, Poly Head & Bowl 200 30 59 SS AA126ML-F7550 **2” Flanged Strainer, Poly Head & Bowl 200 50 59 SS 124-1-1/2-I30 1-1/2" Strainer with CI Head & Nylon Bowl 150 30 70 SS 124-2-I30 2" Strainer with CI Head & Nylon Bowl 150 30 160 * 50mm Flange same as Banjo 1” ** 75mm Flange same as Banjo 2” Std. Port

1-1/2” & 2” 124 Cast Iron

AA126ML Flanged Poly

STRAINERS Net Ea. $ 9.69 9.69 17.95 17.95 17.95 17.95 36.75 36.75 36.75 78.05 177.00

Screen Mesh Openings Mesh Size of Size Color Opening 16 Gray .045" 30 Yellow .021" 50 Red .011" 80 Blue .007" 100 Green .006" 200 Orange .003"

D

POLYPROPYLENE “T” LINE STRAINERS FEATURES:

D

• Heavy-Duty Glass Reinforced Polypropylene

• 304 Stainless Steel Polypropylene Reinforced Screens

• Clean-Out Plug

• 150 PSI @ 70° F.

• EPDM Gaskets

• Flanged Models Also Available STRAINERS

D

Part No. TK LST075-50 TK LST075-80 TK LST100-30 TK LST100-50 TK LST125-30 TK LST150-30

3/4" & 1"

Size 3/4" Poly “T” Strainer 3/4" Poly “T” Stainer 1" Poly “T” Strainer 1" Poly “T” Strainer 1-1/4" Poly “T” Strainer 1-1/2" Poly “T” Strainer

Parts for 3/4" & 1" Strainers

Max. PSI 150 PSI @ 70° F. 150 PSI @ 70° F. 150 PSI @ 70° F. 150 PSI @ 70° F 150 PSI @ 70° F. 150 PSI @ 70° F.

Net Ea. $ 17.51 17.51 17.51 17.51 34.88 34.88

Parts for 1-1/4" & 1-1/2" Strainers

Part No. Net Ea. TK LST130 30 Mesh Screen....................... $ 10.40 TK LST150 50 Mesh Screen....................... 10.40 TK LST180 80 Mesh Screen....................... 10.40 TK LST1100 100 Mesh Screen..................... 10.40 TK LST100B Poly “T” Strainer Bowl............. 7.50 TK LST100G Poly “T” Strainer Gasket-EPDM 1.97 TK LST100GV Poly “T” Strainer Gasket-Viton® 4.20 TK 13778 Screen O-Ring.......................... 1.11

Cut-Away View 3/4" to 1-1/2" Sizes (Typical)

Mesh 50 80 30 50 30 30

Part No. Net Ea. TK LST1530 30 Mesh Screen................ $ 17.05 TK LST1550 50 Mesh Screen................ 17.05 TK LST1580 80 Mesh Screen................ 17.05 TK LST15100 100 Mesh Screen.............. 17.05 TK LST150B Poly “T” Strainer Bowl...... 12.35 TK LST150G Poly “T” Strainer Gasket-EPDM 2.21 TK LST150GV Poly “T” Strainer Gasket-Viton® 5.08 TK LST034G Screen O-Ring................... 1.65

Line Strainers Polypropylene Line Strainers are highly corrosion resistant. For use in handling liquid fertilizer & other chemical solutions. Bottom opening type. EPDM Gasket and cleanout plug.

D

3/4" THRU 2"

• 75 PSI on 1/2" to 1-1/4" • 150 PSI on 1-1/2" to 2" • 75 PSI on 3" Part No.

3"

D

3” 3” FPT DULTMEIER SALES

3" BANJO LINE STRAINER Molded Polypropylene construction. For easy quick cleaning unscrew end cap. Includes a 1/2" drain plug. Stainless Steel screens available in the following sizes: 4, 8, 12, 20, and 50.

OMAHA, NE (800)

228-9666

Ports

TK LS075-40 TK LS075-80 TK LS100-40 TK LS100-80 TK LS125-40 TK LS150-20 TK LS200-20 TK LSM300BC

DAVENPORT, IA (800)

553-6975

3/4" FPT 3/4" FPT 1" FPT 1" FPT 1-1/4" FPT 1-1/2" FPT 2" FPT 3" FPT •

Screen

Net Ea.

40-Mesh $ 16.55 80-Mesh 16.55 40-Mesh 16.55 80-Mesh 18.17 40-Mesh 16.55 20-Mesh 36.45 20-Mesh 36.45 None 186.01

www.dultmeier.com

E0095


Strainers & Filters

188

Thompson Filters “Y” Type Strainers (Cast Iron or Bronze)

Capacities to 750 GPM Pressures to 100 PSI

“Y” Type Line Strainers for plumbing service lines. Available in Cast Iron or Bronze construction. Rated to 400 PSI Water, Oil, or Gas.

D

FPT Stainless Part No. Body Ports Screen Wt. Net Ea. WS 77S-3/4 Cast Iron 3/4" 20-Mesh 2.5 lbs. $ 12.25 WS 77S-1 Cast Iron 1" 20-Mesh 4 lbs. 17.45 WS 77S-1-1/4 Cast Iron 1-1/4" 20-Mesh 4.5 lbs. 28.95 WS 77S-1-1/2 Cast Iron 1-1/2 20-Mesh 6.5 lbs. 27.95 WS 77S-2 Cast Iron 2" 20-Mesh 13 lbs. 42.95 WS 77S-3 Cast Iron 3” 20-Mesh 30 lbs. 159.50 WS 777S-3/4 Bronze 3/4" 20-Mesh 1 lbs. 38.95 WS 777-1 Bronze 1” 20-Mesh 1 lbs. 35.95 WS 777-1-1/2 Bronze 1-1/2" 20-Mesh 3 lbs. 71.95 WS 777S-2 Bronze 2" 20-Mesh 9 lbs. 109.00

Ports

DE S2B-40 DE S2B-80 DE S3B-40 DE S3B-80 DE S4B-40 DE S4B-80 DE S6B-40 DE S6B-80

Screen

Screen Mesh : Wire Diameter

Open Area

1/4" Perforated 20 Gauge Sheet 1/8" Perforated 20 Gauge Sheet 16 Mesh Screen .023" 30 Mesh Screen .013" 40 Mesh Screen .010" 50 Mesh Screen .009" 60 Mesh Screen .0075 80 Mesh Screen .0055 100 Mesh Screen .0045

58.00% 40.30% 39.90% 37.10% 36.00% 30.30% 30.50% 31.40% 30.30%

4” Model

Body

2" & 3" Models

Note: 2" and 3" Filters use a quick remove V-Band type clamp to secure the top Cover. 4" & 6" models have bolt on covers. 2" & 3" Sizes have NPT threaded inlet/outlet ports.

Dimensions “A” “B”

Net Ea.

1/4"FPT 40-Mesh Bronze 1-1/4" 1-1/4" $ 19.20 1/4"FPT 80-Mesh Bronze 1-1/4" 1-1/4" 19.20 3/8"FPT 40-Mesh Bronze 2-1/4" 1-1/4" 19.35 3/8"FPT 80-Mesh Bronze 2-1/4" 1-1/4" 19.20 1/2"FPT 40-Mesh Bronze 2-1/2" 1-1/2" 23.00 1/2"FPT 80-Mesh Bronze 2-1/2" 1-1/2" 23.00 3/4"FPT 40-Mesh Bronze 3-1/4" 2" 44.85 3/4"FPT 80-Mesh Bronze 3-1/4" 2" 44.85

Steel Suction Strainer

D

Inlet/Outlet Maximum Filter Area Debris Part No. Style * GPM Sq. In. Flush Port Wt. Net Ea. DU MLI2 2" MPT 100 122" 1/2" NPT 12 lbs. $ 777.00 DU MLI3 3" MPT 200 200" 1" NPT 26 lbs. 1481.00 DU MLI4B 4" Flanged 350 367" 2" NPT 60 lbs. 2185.00 * Filters priced above have screens installed. Please specify required mesh size.

Especially suited to handle the high capacity pump on today’s modern equipment. Zinc chromate plated Suction Strainers. 16-Gauge. 1/4" openings. Prevents large particles from entering suction port of pumps

D

D

D

Bronze Body and Stainless Steel Screens in 40 or 80 mesh for water and other liquids where a nonferrous strainer is applicable. Y-Type for hard-to-get-at spots. Quick cleaning when required. Pressure Rating: 300 PSI @ 150° F. or 150 PSI @ 375° F. Part No.

These unique Filter Systems feature a coni­cal screen element that gives the filter a selfcleansing ability and the advantage of large screen area providing high capacities with low pressure loss. Debris is collected in a chamber below the screen for pe­riodic flushing through a fitting in the bottom of the filter. Filters in­clude two 1/4" gauge ports. Strainer Includes Screen – Select from these Sizes

Y-Type Strainers (Bronze)

304 Stainless Steel Construction throughout

Aluminum Strainer 1/2” MPT

Part No.

FPT Port Diameter Net Ea. EV RHS20 1-1/2" 5" $ 10.80 EV RHS25 2" 6" 12.50 EV RHS35 3" 7" 18.40 EV RHS40 4" 7" 20.60

Inline Aluminum Strainer common replacement item for many pressure wash pumps. Rated to 10 gpm and 170 psi. 50 Mesh screen is standard. Inlet port is 3/4” FGHT or 1/2” FPT. Outlet port is 1/2" MPT.

1/2” FPT

D

3/4” FGHT

Molded Polyethylene Strainers

Part No.

Net Ea.

IP AL75

$ 11.95

Inline Strainer

For Hose End Suction Part No.

PR 0734 PR 0733 PR 0757

FPT Port

1-1/2" 2" 3"

Diameter Net Ea.

5-1/4" 5-1/4" 7-7/8"

DULTMEIER SALES

$ 4.95 4.95 12.95

OMAHA, NE (800)

D

Viton® is a registered trademark of DuPont Performance Elastomers

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0935


Filters/Strainers • Solids Separators

189

TwistIIClean® Filter/Strainers

Sand/Fine Solids Separators

LAKOS Inline Filter/Strainers. Patented “Twist-to-Clean-Design”. Ideal for industry, agriculture, water well, irrigation, misting systems, etc. Just a 1/4 turn of the handle starts the reverse flushing action which backwashes from inside out. Debris is cleaned off the screen and flushed out the bottom purge port. Polypropylene/acrylic body. EPDM top seal, Viton® bottom seal. Stainless steel screen. MPT or flange ports as noted. Rated to 100 PSI and 120° F.

Features: • No Disassembly Required to Clean • Completely Flushes and Cleans in Just 20 Seconds • No Need to Turn Off Liquid Flow

LAKOS Centrifugal-Action Separators are designed to remove sand, grit and other fine solids from source water systems. Removes up to 98% of 200 mesh, (74 micron) particles and larger. For heavier solids like metal chips, even better results can be expected. Unique design has no moving parts and does not require screens or filters to be cleaned or replaced. Available in Carbon Steel (ILB) and Stainless Steel (ILS) construction. Separators must be periodically purged and manual or automatic purging systems matched to specific applications are also available. Purging can be done during operation with no loss of performance. Flow rates to 290 GPM. Pressures to 150 PSI. Low pressure loss 5-12 PSI. Rated for solids from 50 to 200 mesh. Purge ports is 3/4” MPT on all models.

• No Tools Needed for Cleaning D

D

Purge Exit

MPT Ports

Model ILB

Flange Ports

D

D

3/4” 1” 1-1/2” Filters

2” Filters

Purge Port

Purge Port

D

Model ILS

Over 200% Larger Stainless Steel Screen Area lasts for years, collects maximum debris between cleanings. Clear bowl shows when filter needs cleaning.

Part No. DM 131344 DM 131345 DM 131348 DM 131349 DM 131554 DM 131555 DM 131557 DM 131558

Inlet/Outlet Purge Ports Port Mesh Micron 3/4” MPT 1/2” MPT 60 250 3/4” MPT 1/2” MPT 100 150 1” MPT 1/2” MPT 60 250 1” MPT 1/2” MPT 100 150 1-1/2” MPT 3/4” MPT 60 250 1-1/2” MPT 3/4” MPT 100 150 2” Flange 3/4” MPT 60 250 2” Flange 3/4” MPT 100 150

Max. Flow 25 GPM 25 GPM 39 GPM 39 GPM 78 GPM 78 GPM 150 GPM 150 GPM

Length 11-3/4” 11-3/4” 11-3/4” 11-3/4” 15-1/4” 15-1/4” 25” 25”

Net Ea. $ 51.95 51.95 51.95 51.95 69.95 69.95 339.50 339.50

Part No. DM ILB0050 DM ILS0050 DM ILB0075 DM ILS0075 DM ILB0100 DM ILS0100 DM ILB0125 DM ILS0125 DM ILB0150 DM ILS0150 DM ILB0200 DM ILS0200 DM ILB0300 DM ILS0300

Ports 1/2” MPT 1/2” MPT 3/4” MPT 3/4” MPT 1” MPT 1” MPT 1-1/4” MPT 1-1/4” MPT 1-1/2” MPT 1-1/2” MPT 2” MPT 2” MPT 3” MPT 3” MPT

Construction Flow Rate Wt. Carbon Steel 4-10 GPM 14 lbs. Stainless 4-10 GPM 14 lbs. Carbon Steel 10-20 GPM 16 lbs. Stainless 10-20 GPM 16 lbs. Carbon Steel 19-32 GPM 27 lbs. Stainless 19-32 GPM 27 lbs. Carbon Steel 28-48 GPM 27 lbs. Stainless 28-48 GPM 27 lbs. Carbon Steel 45-70 GPM 27 lbs. Stainless 45-70 GPM 27 lbs. Carbon Steel 65-108 GPM 55 lbs. Stainless 65-108 GPM 55 lbs. Carbon Steel 148-290 GPM 135 lbs. Stainless 148-2090GPM 135 lbs.

Net Ea. $ 419.00 941.00 446.00 975.00 497.00 1035.00 538.00 1175.00 595.00 1258.00 769.00 1950.00 1447.00 3937.00

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E1008


190 Cast Iron Flanged Y-TYPE Strainers

Carbon Steel Flanged Y-TYPE Strainers • Standard with 150/Lb. ANSI

• Standard with 125/Lb. ANSI Flanges (FF)

Flanges (RF); 300 Lb. Flanged Models Also Available.

• 2” - 24” Sizes.

• 1/2” - 24” Sizes.

• Standard with 1/16” 304 SS Perforated Screens on 1/2” - 4” sizes; 1/8” on 6” - 14” sizes; Many Other Screen Sizes Available.

• Standard with 1/16” 304 SS Perforated Screens on 1/2” - 4” sizes; 1/8” on 6” - 14” sizes; Many Other Screen Sizes Available.

D

• Drain Plug Available. Part No. Description

DZ S2 DZ S3 DZ S4 DZ S6 DZ S8

2” Cast Iron Flanged Y-Strainer 3” Cast Iron Flanged Y-Strainer 4” Cast Iron Flanged Y-Strainer 6” Cast Iron Flanged Y-Strainer 8” Cast Iron Flanged Y-Strainer

• Drain Plug Available.

Standard Screen

Net Ea.

$ 76.50 92.45 147.50 308.50 586.00

1/16” Perf. 1/16” Perf. 1/16” Perf. 1/8” Perf. 1/8” Perf.

Part No. Description

DZ SA7-2 DZ SA7-3 DZ SA7-4 DZ SA7-6 DZ SA7-8

Standard Screen

2” Carbon Steel Flanged Y-Strainer 1/16” Perf. 3” Carbon Steel Flanged Y-Strainer 1/16” Perf. 4” Carbon Steel Flanged Y-Strainer 1/16” Perf. 6” Carbon Steel Flanged Y-Strainer 1/8” Perf. 8” Carbon Steel Flanged Y-Strainer 1/8” Perf.

Cast 316 Stainless Flanged Y-TYPE Strainers

Part No. Description

DZ SSA7-2 DZ SSA7-3 DZ SSA7-4 DZ SSA7-6 DZ SSA7-8

Standard Screen

2” S.S. Flanged Y-Strainer 3” S.S. Flanged Y-Strainer 4” S.S. Flanged Y-Strainer 6” S.S. Flanged Y-Strainer 8” S.S. Flanged Y-Strainer

• Designed with straight thru flow design (with angular cut-away design screens) for extremely low pressure loss. • Standard with bolted top cover flange (wingnut style covers also available for even faster cover removal).

D

• Standard with 1/16” 304 SS Perforated Screens on 1/2” - 3” sizes; 1/8” on 4” - 14” sizes.

Net Ea.

$ 558.00 984.00 1567.00 3094.00 5433.00

1/16” Perf. 1/16” Perf. 1/16” Perf. 1/8” Perf. 1/8” Perf.

• Drain Plug Available. Part No. Description

DZ GFV-2 DZ GFV-3 DZ GFV-4 DZ GFV-6 DZ GFV-8

Cast Bronze Flanged Y-TYPE Strainers • Constructed with rugged nickel aluminum bronze castings.

2” Cast Iron Flanged Y-Strainer 3” Cast Iron Flanged Y-Strainer 4” Cast Iron Flanged Y-Strainer 6” Cast Iron Flanged Y-Strainer 8” Cast Iron Flanged Y-Strainer

D

Part No. Description

2” Bronze Flanged Y-Strainer 3” Bronze Flanged Y-Strainer 4” Bronze Flanged Y-Strainer

Standard Screen

• Fabricated Custom Tee & Basket Strainers

Cast Bronze Threaded Y-TYPE Strainers

• Fabricated Custom Duplex Basket Strainers for Continuous Flow Applications

• Standard with 125/Lb. Threaded FNPT Ports. • Threaded Cap & Drain Plug Available. Part No. Description

DZ F150-12 DZ F150-34 DZ F150-1 DZ F150-2 DZ F150-3

Net Ea.

$ 244.00 326.00 433.50 740.00 1310.00

• Fabricated Custom Y Strainers

Net Ea.

$ 811.00 1485.00 2413.00

1/16” Perf. 1/16” Perf. 1/16” Perf.

D

1/16” Perf. 1/16” Perf. 1/8” Perf. 1/8” Perf. 1/8” Perf.

Also Offers:

• Drain Plug Available.

DZ BA-2 DZ BA-3 DZ BA-4

Standard Screen

Other Strainers Available from Keckley

• Standard with 150/Lb. ANSI Flanges • Standard with 1/16” 304 SS Perforated Screens on 1/2” - 4” sizes; 1/8” on 5” - 12” sizes; Many Other Screen Sizes Available.

Net Ea.

$ 304.50 382.00 638.00 1063.00 CALL

Cast Iron Flanged Basket Strainers

• Standard with 150/Lb. ANSI Flanges (RF); 300 Lb. Flanged Models Also Available. • Standard with 1/16” 304 SS Perforated Screens on 1/2” - 4” sizes; 1/8” on 6” - 14” sizes; Many Other Screen Sizes Available. • Drain Plug Available.

D

D

Standard Screen

1/2” Bronze Threaded Y-Strainer 20 Mesh 3/4” Bronze Threaded Y-Strainer 20 Mesh 1” Bronze Threaded Y-Strainer 20 Mesh 2” Bronze Threaded Y-Strainer 20 Mesh 3” Bronze Threaded Y-Strainer 1/16” Perf. DULTMEIER SALES

OMAHA, NE (800)

Net Ea.

$ 18.55 22.35 29.50 82.35 366.00

228-9666

• Temporary Pipeline Strainers (Cone, Basket, Plated)

Call with Your Application Requirements DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E1001


Check Valves

191

Low Pressure Check Valves

High Pressure Brass Check Valves

Bronze & Stainless

Unleaded Bronze and 303 Stainless Check Valves are designed for full fluid flow. Female x Female ports and stainless steel springs. Buna seals in Bronze valves and Viton® in Stainless. 1/4” through 2” can be installed vertical or horizontal (3” & 4” are recommended for vertical mount only). Rated to 400 PSI WOG (except 1/4” & 3/8” which are rated to 200 PSI. Maximum temperatures to 180° F. D

Series 600 Bronze D

303 Stainless

UNLEADED BRONZE Part No. Ports Material Net Ea.

WS 600-1/4 1/4" Bronze $ 37.65 WS 600-3/8 3/8" Bronze 37.95 WS 600-1/2 1/2" Bronze 27.50 WS 600-3/4 3/4" Bronze 27.95 WS 600-1 1" Bronze 29.65 WS 600-1-1/4 1-1/4" Bronze 41.70 WS 600-1-1/2 1-1/2" Bronze 56.85 WS 600-2 2" Bronze 89.90 WS 600-3 3” Bronze 420.00 WS 600-4 4” Bronze 729.00

303 STAINLESS Part No. Ports Material

Net Ea.

KC 830202 3/8” Stainless $ 48.85 KE 623 1/2” Stainless 11.75 KE 624 3/4” Stainless 17.95 KE 625 1” Stainless 29.70 KE 626 1-1/4” Stainless 47.90 KE 627 1-1/2” Stainless 38.95 KE 628 2” Stainless 63.95 KE 629 3” Stainless 276.00 Viton® is a registered trademark of DuPont Performance Elastomers

Medium Pressure Brass Check Valves These bubble-tite in-line check valves feature minimum cracking pressure (0-1 psi) and positive check.Vir­tually “problem proof”, these valves install easily in any appli­cation. Body, poppet and retainer plug are Brass with a Stainless spring and Viton® O-ring. Part No.

Ports

GE 1CV-125 GE 1CV-250 GE 1CV-375 SM 410-4MBB

Max. PSI

* 1/8" MPT x 1/8" MPT * 1/4" MPT x 1/4" MPT † 3/8" MPT x 3/8" MPT † 1/4" MPT x 1/4" MPT

* Generant Brand. † SMC Brand.

Part No. UP CV3201B1 UP CV3301B1 UP CV3401B1 UP CV3601B1 UP 40083 UP 40082 UP 40080 UP 40081

D

All brass body, stainless steel ball, PVC cage and a quad ring seat for a “bubble-tight” seal. Cracking pressure is less than 1 PSI. Maximum operating temperature is 180° F.Standard with Ethylene Propylene seals for added chemical resistance. Maximum operating pressure is 3000 PSI. Available in either 1/4" or 3/8" sizes.

Part No. SM 450-4F4FB SM 650-6F6FB SM 850-8F8FB

Net Ea. D

Max. PSI 1200 1200 1200

— Low Pressure —

Chemical Resistant Check Valves are constructed of polypropylene with EPDM or Viton ® seals. Rated to 125 psi and 140° F. Standard with stainless steel spring. Easily disassembled for seal replacement if needed. Max. Part No. FPT Ports Seal PSI Net Ea.

EPDM 125 $ 5.05 EPDM 125 5.25 EPDM 125 5.55 EPDM 125 6.30 Viton® 125 5.30 Viton® 125 5.50 Viton® 125 5.85 Viton® 125 6.60

470-4F4F

D

Part No.

Constructed of 303 stainless steel. A viton o-ring provides absolute leak-proof operation. Valves are completely rebuildable. Maximum of 3500 PSI. Available in 1/4", 3/8" and 1/2" x 3/4" sizes. Cracking pressure is approximately 5 PSI. Rated to 210° F. * T Series Check Valves have the same features as the SP Series, but feature Teflon O-rings and is rated to 300° F. Ports GPM Net Ea. REPAIR KITS

1/4" FPT 3/8" FPT 1/2" FPT 3/4" FPT *1/4" FPT *3/8" FPT *1/2" FPT *3/4" FPT

3 6 12 20 3 6 12 20

$ 18.30 24.95 30.30 40.30 18.80 25.30 31.40 41.25

FL CV100-RK $ 8.33 FL CV600-RK 9.18 FL CV700K 9.13 FL CV800-RK 14.60 FL CV100T-RK 8.59 FL CV600T-RK 9.35 FL CV700T-RK 9.35 FL CV800T-RK 14.95

Cracking pressure is 8 PSI. Maximum temperature is 195° F. Viton® Seals. Standard on many PDQ wash systems. Part No. FPT GPM Max. PSI Net Ea.

D

These valves will work in either a horizontal or vertical position. Inlet and outlet is FPT. Cracking pressure is 1 psi.

Low Pressure

Net Ea. $ 9.85 9.89 9.52 In

470-4M4F

Stainless Check Valves

• Polypropylene Bodies • Viton® Seals • 316SS Ball • 1 PSI Crack Opening Pressure

DULTMEIER SALES

D

— High Pressure • High Temperature —

Hose Barb Polypropylene Check Valves

Part No. Hose Barb BU CV1101-B38 3/8” BU CV1101-B12 1/2” BU CV1101-B14 1/4”

Net Ea.

High Pressure Stainless Check Valves

FL CV100SP FL CV600SP FL CV700 FL CV800SP-1 FL CV100T FL CV600T FL CV700T FL CV800SP-1T

Net Ea. $ 6.72 7.95 10.40

Polypropylene Check Valves

SM 681-4E 1/4" SM 683-6E 3/8” SM 685-8E 1/2" SM 687-12E 3/4" SM 681-4VV 1/4” SM 683-6VV 3/8” SM 685-8VV 1/2" SM 687-12VV 3/4"

OUTLET

Fluid Control

Brass Check Valves rated to 1200 PSI feature Buna o-ring poppet seal for bubble-tight operation. Cracking pressure is 3 PSI. Rated to temperatures of 180° F.

Size 1/4" FPT 3/8" FPT 1/2" FPT

INLET

D

SM 470-4F4F 1/4" FPT 1/4" FPT $ 13.65 SM 470-4M4F 1/4" MPT 1/4" FPT 13.65 SM 470-6F6F 3/8" FPT 3/8" FPT 13.65 SM 470-6M6F 3/8" MPT 3/8" FPT 13.65

Medium Pressure Brass Check Valves

D

Ports Max. PSI Net Ea. 1/4" FPT 2000 $ 30.50 3/8" FPT 2000 35.45 1/2" FPT 2000 62.95 3/4" FPT 2000 108.00 Repair Kit for 1/4” & 3/8” Valves....... 2.71 Repair Kit for 1/2” Valves.................. 3.71 Repair Kit for 3/4" Valves................. 4.96 Repair Kit for 1” Valves..................... 11.25

High Pressure Brass Check Valves

Part No.

500 $ 7.50 800 7.50 500 8.75 500 7.15

For protection against reverse flow. Allows free-flow in one direction. Seat design protects “O” ring seal from contamination or flow damage. Install in any position. Temperature range -20° to +400° F. Opens @ 3 to 5 psi. Viton® seal. Stainless Steel spring. Brass construction.

BARBS

OMAHA, NE (800)

Out

228-9666

IP YCV14FSS 1/4" 6.5 IP YCV38FSS 3/8” 10 IP YCV12FSS 1/2" 21 IP YCV34FSS 3/4” 47

5,800 $ 24.55 5,800 24.55 5,800 32.70 5,800 48.60

D

Stainless Steel Check Valves High Pressure

“Maxi-Flow “ Check Valves. Stainless steel D construction. Positive check, no leaks. Cracking pressure is less than 1 PSI.Maximum flow rate is 4 GPM. Maximum working pressure is 5,000 PSI.Standard with “EPR” seal for added chemical resistance. Maximum temperature is 300° F. Overall length is 2.33". Part No. Inlet Outlet Max. PSI Net Ea. AA 7375 1/4" FPT 1/4" FPT 5,000 $ 14.80 AA 7450 1/4" MPT 1/4" MPT 5,000 14.80 AA 7462 1/4" MPT 1/4" FPT 5,000 14.80 AA 7463 1/4" FPT 1/4" MPT 5,000 14.25 DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0097


Foot Valves

192

PVC Foot Valve Operates in any position. Teflon ball and Quad ring seat. Cracking pressure 1 PSI. Maximum operating pressure 125 PSI. Maximum operating temperature 140° F. Ethylene Propylene seals are standard for added corrosion resistance. Standard with 3/8" hose barb on one end and 50-mesh strainer screen on other end.

Foot Valves Dema Heavy-Duty Foot Valves with strainers. PVC body, stainless steel spring, valve seat and EP rubber ball. Fits 1/4" or 3/8" I.D. tubing. Replaceable strainer is 60-mesh. Part No.

Tubing

DE 902 DE 903

1/4" I.D. 3/8" I.D.

D

903

Net Ea.

$ 15.75 15.75

D

PFV150

Part No.

Tubing Size

Bronze Foot Valves

Net Ea.

SM 426-6B6BE 3/8" $ 7.69 HR 113 Ceramic Weight, 1/4" or 3/8" tubing 2.40

Industrial Foot Valves. Bronze body with stainless steel screen, cap and spring. Ideal for use in light duty commercial or domestic well systems.

Suction Filter Foot Valve

D

Glass filled Polyamid Inlet Strainer with Check Valve. Designed for larger size chemical or suction hose requirements. Prevents backflow. Part No.

HOSE BARB

NP ST35R NP ST35R-1

1/2" & 3/4" 3/4" & 1"

CFV125

D

Net Ea.

$ 14.45 14.45

ST35R

Foot Valves HR 113

HY 3350-128

Ceramic Weights for above valves: #113 Weight fits over 1/4" or 3/8" tubing. #114 Weight fits inside 1/2" tubing. Part No.

Net Ea.

EPDM Foot Valve - no weight........ $ 6.55 Viton® Foot Valve - no weight...... 8.75 Ceramic Weight, 1/4" or 3/8" tubing 2.40 Ceramic Weight, 1/2" tubing........... 4.10

PVC Foot Valves up to 2" inlet size. Gives positive back flow seal protection. Designed for use at the end of suction lines. PVC Type II bodies. 1/2 lb. closing pressure. 150 PSI rating.

D

Dimensions Ports

JK KV500T 1/2" FPT JK KV750T 3/4" JK KV100T 1" JK KV125T 1-1/4" JK KV150T 1-1/2" JK KV200T 2"

Net Ea.

$ 7.62 7.76 10.95 14.35 16.10 22.80

1/4" Foot Valve

$ 4.65

Foot Valves Foot Valves for chemical lines. Step-down barb design allows for use with 1/4", 3/8" or 1/2" tubing. Designed for one-way flow of product and positive seal against flow in the opposite direction. Model 100-11 has stainless body with spring and ball and 1/4” barb. Model 100-11P has a poly body with stainless spring and ball with EPDM O-ring. Model 100-11PCV features poly body,Teflon ball, hasteloy spring and Viton® O-ring. CeramicWeights for 100-11P & 100-11PCV: #113 D Weight fits over 1/4" or 3/8" tubing. #114 Weight fits inside 1/2" tubing. Part No.

PVC Spring Check Foot Valves

KV 500T

D

Part No. Net Ea.

Models 101 & 102 Valves are foot valves only. Standard with a step-down barb assembly that will work with 1/4", 3/8" or 1/2" tubing.

Part No.

Corrosion-Resistant Foot Valve for chemical lines. Brass body and barb with 50 mesh stainless screen. Inlet barb is 1/4"

HR 102

HYDRO FOOT VALVES allow one-way flow of chemical concentrations. Prevents solutions from “back-flowing” into supply tubing. Constructed of corrosion-resistant plastic and rubber materials for longer life. Polypropylene bodies with EPDM or Viton® diaphragms. (EPDM is recommended for Butyl base chemicals found in some tire cleaner products).

HR 101 HR 102 HR 113 HR 114

Part No. FPT Port Length Diameter Wt. Net Ea. WS CFV075 3/4" 2-3/8" 1-3/8" 5 oz. $ 8.27 WS CFV100 1" 2-3/8" 1-5/8" 6 oz. 13.30 WS CFV125 1-1/4" 3-1/4" 2" 7 oz 17.00 WS PFV150 1-1/2" 3-7/8" 2-3/8" 2 lbs. 28.95 WS PFV200 2" 4" 3" 3 lbs. 44.25 WS PFV300 3” 9-1/2” 4-3/4” 6 lbs. 124.50

Stainless Steel / Brass Foot Valve

HR 114

HR 101

D

Size K H 1/2" 6.40 2.30 3/4" 6.40 2.30 1" 6.40 2.30 1-1/4" 7.00 2.75 1-1/2" 7.00 2.75 2" 7.00 3.35

DE 100-11 DE 100-11P DE 100-11PCV HR 113 HR 114

100-11PCV & 100-11P

D

100-11

Net Ea.

Foot Valve, BUNA O-ring................. $ 2.62 Foot Valve, EPDM O-ring................ 2.63 Foot Valve, VITON® O-ring............. 3.97 Ceramic Weight, 1/4" or 3/8" tubing 2.40 Ceramic Weight, 1/2" tubing............ 4.10

Strainer / Foot Valves Strainers and Foot Valves from SUTTNER! Chemical resistant, plastic construction. ST31 is a strainer only. ST31R is a strainer with a built-in Viton®/ Stainless check valve that prevents “backflow”. Inlet step-down barbs will accept either 1/4" or 3/8" I.D. tubing. Length D on both is 2.9". Diameter is .795".

ST35R

Part No.

Description Net Ea.

NP ST31 NP ST31R HR 113

Strainer Only.................................... $ .95 Foot Valve & Strainer....................... 1.57 Ceramic Weight, 1/4" or 3/8" Tubing 2.40

Viton® is a registered trademark of DuPont Performance Elastomers

E0096


Sprayers • Utility Carts

193 15 Gallon

Sure Shot Sprayers

12-Volt Spot Sprayers For unlimited uses such as lawn and garden, fence rows, trees, shrubs and cattle spraying. Premium poly tanks with threaded fasteners molded in bottom side of tank.

D

• Refillable • Rechargeable • Portable

Features: 3-Year tank warranty • 5" Screw on fill cap with vent • 15 feet of 3/8" coiled spray hose • Spray wand with fully adjustable spray tip • 96” wire harness with alligator clips and inline on/off switch. Models SP14, SP15, SP25 feature ShurFlo 12-volt Pumps with adjustable demand switch. Model AR25 uses a ShurFlo Pump rated at 3.5 GPM. Includes pressure regulating valve to keep pump from cycling on and off. 15’ of non-coiled hose.

• Eliminates Aerosol Cans & Disposal Problems.

Part No.

An excellent choice for applying a wide variety of liquid products such as bug cleaners, glass cleaners, presoak products, tire/whitewall cleaners, air fresheners, deodorizers, insect repellents, rubber dressings, rust inhibitors and many more. Just fill your canister, pressurize with air, point and spray. Recharge and refill as needed. Sure Shot Sprayers feature Viton® seals and are available in enamel-coated steel construction for non-water products or chrome-plated brass construction for water soluble products except ammonia. (Chemical compatibility should be checked prior to use on all models.) Model 1000 & 2000 Sprayers are 32 oz. capacity and include a general purpose misting nozzle and a pin stream nozzle. Other nozzles types are available if required. Model 300 Nozzle Assortment Kit includes the following nozzles: 302B, 302C, 305, 501, & 602.

Size Max. Amp Gallons Power Pump GPM PSI Draw

DU SP14 DU SP15 DU SP25 DU AR25

15 15 25 25

12-Volt DC 12-Volt DC 12-Volt DC 12-Volt DC

Diaphragm Diaphragm Diaphragm Diaphragm

1.8 1.0 1.8 3.0

Net Ea.

7.3 $ 157.50 4.0 159.00 7.3 175.50 9.6 218.50

60 60 60 60

Spray Units for Tire or Bug Cleaning Complete spraying units for car prep of bug cleaner or tire cleaner solutions. Available in 14 or 25 gallon tank sizes. Rated for 115V. Pumps have a built-in switch which shuts pump off when liquid flow is stopped, (trigger gun is shut) and cut-out pressure (60 PSI) is reached. Part No.

DU SP14-115 DU SP24-115

115 Volt

Part No. Net Ea. MQ 1000R Red Enamel Steel Sprayer ...... $ 53.75 MQ 2000 Chrome Plate Brass Sprayer .. 77.75 MQ 300 Nozzle Assortment Kit ............ 27.60 MQ 301 Nozzle as replacement ........... 3.49 MQ 302 Nozzle as replacement ........... 4.70 MQ 302B Nozzle as replacement ........... 4.70 MQ 302C Nozzle as replacement ........... 6.70 MQ 305 Nozzle as replacement ........... 10.55 MQ 501 Nozzle as replacement ........... 12.50 MQ 602 Nozzle as replacement ........... 8.69 MQ 707 Nozzle as replacement ........... 16.50 MQ 10 Repair Kit, complete ................ 21.75

D

All units include 25’ of 3/8” hose, trigger gun, pump, tank and all necessary fittings. Units are pre-plumbed. GPM

1.3 1.3

Tank

D

Net Ea.

14 gallon $ 205.00 25 gallon 213.50

Viton® is a registered trademark of DuPont Performance Elastomers

Utility Carts Heavy Duty, Portable Utility Carts for Car Washes, Automotive Repair, Detail Shops and many more. Ideal for organizing cleaning supplies, detailing products, tools, etc. Designed for a wide variety of uses. Polyethylene construction that won’t scratch, rust, dent or stain. Lifetime warranty on all carts. STC and TC models feature all polyethylene construction with (4) 4” casters, two with locking brakes. Standard color is black, but grey is also available. (3) Tub style shelves are shown but 2 and 4 shelf units or flat shelves are also available. Top Shelf is reinforced with an aluminum bar on STC111.

STC Models feature the top shelf reinforced with aluminum, total rated capacity of 300 lbs. Distance between shelves is 12”. TC Models have all shelves reinforced with aluminum and a capacity of 400 lbs. with standard wheels or up to 800 lbs. with wheel change option. Distance between shelves is 11”.

All Shelves reinforced on TC111

ATC332 Model features a sturdy metal frame with adjustable polyethylene tub shelves. (4) 3” Casters, two with locks are standard. Rated capacity is 200 lbs. MS21B Mechanic’s Seat features all polyethylene construction. Tub bottom shelf is 2-3/4” deep. (4) Casters, two locking are standard. Padded seat is included. Rated to 300 lbs. Padded Seat Plastic Tub Shelves will not rust, dent or stain

D

D

Sturdy Metal Frame Tub Shelf

MS21B

D

Part No.

ATC332 3” Easy Roll Casters DULTMEIER SALES

Plastic Shelves & rounded corners will not mar car’s finish. Also oil & stain resistant

Tub Shelves are 2-3/4” deep

LX STC111 LX TC111 LX ATC332 LX MS21B LX STC8BH

Width

Depth

Height

4” Easy Roll Casters

Wt.

24” 18” 38-1/2” 29 lbs. 32” 24” 36” 65 lbs. 22” 15-1/2” 32” 20 lbs. 24” 18” 20” 25 lbs. Bottle Holder for STC Carts Only.......

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

STC111 & TC111 Net Ea.

Flat Shelf for STC or TC Units (as option)

$ 109.00 150.00 117.50 70.05 27.45

553-6975

Easy Roll 4” Casters

D

www.dultmeier.com

E0675


Sprayers • Applicator Units Detail Sprayers

194

Chemical Applicator Units

Stainless Steel Compressed Air Sprayers for degreasers, bug cleaners, tire dressing, vinyl dressings, weed spray and many more. Constructed of 304SS. Available in 3 gallon or 5 gallon sizes. Rechargeable design, fill from your air compressor to 125 psi. All sprayers include coil hose and trigger spray wand with adjustable pattern nozzle. The Dress Pro is the standard 3 gallon sprayer, but includes a wheel brush and valve for easy tire dressing applications with less waste. (No sponges or sprayers are needed).

Chemical Applicator Units are designed for use with highly corrosive chemicals like aluminum brighteners or concrete cleaners. These systems draw chemicals directly from the original chemical containers which reduces employee handling and exposure. No pumps are needed, only water or air pressure. All units come with 40’ discharge hose and wand assembly. Wall mounted, space saving design. Rated to 150 PSI and 160° F.

Stainless steel carts are also available to make the 5 gallon sprayers even more portable. Available in single or double cart design with wheels and hose hooks. D

30SP & 50SP 3 Gallon Sprayer (includes 10' Hose)

D

D

972306

3DP2 3 Gallon "Dress Pro" (includes 10' hose & brush)

D

DP02 Brush Only

D

972012

972307

972211

D

All sprayers are high quality, reconditioned, stainless tanks that are double pressure tested prior to shipping. Part No.

PS 30SP PS 50SP PS 3DP2 PS DP02

Tank Size

Wt.

Available in 3 different styles: Direct Spray, Airless Foam or Air Assist Foam. All three styles are available in 1 or 2 chemical models. Two chemical systems allow for two different chemicals to be used through the same system.

Net Ea.

3 Gallon Sprayer 9 lbs. $ 231.00 5 Gallon Sprayer 12 lbs. 261.00 3 Gallon Dress Pro 11 lbs. 263.00 Replacement Brush, 3DP2......... 23.95

Direct Spray, Non-Foaming Units produce a uniform solution spray for even coverage. Dilutions rates up to 3.2:1 are available with these systems. Airless Foam Units produce a wet foam with just city water pressure. Dilution rates up to 4:1 are available with these systems.

Compressed Air Sprayers

Air Assist Foam Units produce a rich, clinging foam that is created with city water pressure and compressed air. Chemical metering tips are included for a wide variety of dilution rates. Part-No. System Type Chemicals Wt. Net Ea. LF 972011 Direct Spray 1 17 lbs. $ 256.00 LF 972012 Direct Spray 2 18 lbs. 319.00 LF 972211 Airless Foam 1 17 lbs. 269.50 LF 972212 Airless Foam 2 18 lbs. 319.00 LF 972306 Air Assist Foam 1 21 lbs. 379.00 LF 972307 Air Assist Foam 2 26 lbs. 445.00

LT50X

Stainless Steel Compressed Air Sprayers for a wide variety of cleaning solutions. Rated to 120 psi, these sprayers are ideal for car washes, industrial cleaning, rental companies or commercial cleaning. Sprayers are cart mounted and include a 25' hose, spray gun and spray lance. Stainless steel tanks are available in either 6 gallon or 13 gallon capacity. Standard with Viton® seal.

PreSpray & Spotter Sprayers

LT24 Sprayer is standard with a 30" lance. D

LT50X Sprayer is standard with 39" lance. Part No.

IP LT24X IP LT50X

Wt.

Great for Presprays, Deodorizers, Sanitizers, Protectors & Dyes

Net Ea.

These sprayers are designed to be attached to your solution pressure line to automatically draw concentrated chemicals from the 5 quart tank. Great for presprays, deodorizers, sanitizers, protectors and dyes. Trigger-style spray wand features 20” extension and 42” hose includes quick attach couplers for easy hookup. Available in low pressure (400 PSI, 8-1 ratio), or high pressure (1000 PSI, 4-1 ratio).

26 lbs. $ 558.00 42 lbs. 867.00

6 Gallon Stainless Sprayer 13 Gallon Stainless Sprayer

Trigger Sprayer No. 300 Trigger Sprayer

Unique design allows this sprayer to work with a bottle held at any angle, even upside down. Leakproof design also means no spills or mess. Plastic construction can be used with a wide variety of cleaning chemicals. Spray bottles are high density polyethylene, 32 oz. capacity and feature oz/ml scale. Part No.

TO 300 TO 120125

D

D

No. 120125 Spray Bottle

Std. Pkg.

Net Ea.

Trigger Sprayer............ 100 $ 1.15 32 Oz. Spray Bottle...... 32 .75 10% Discount on Std. Pkg. DULTMEIER SALES

OMAHA, NE (800)

Part No.

Max. PSI

Ratio

Wt.

400 1000

8-1 4-1

7 lbs. 7 lbs.

TE 507 TE AS08

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

Net Ea.

$ 116.50 129.50 E0677


Sprayers • Acid Applicator

195

Bleach Sprayer

Backpack Mist Blower Model 1201S

Handheld sprayer specifically design for Bleach Solutions. Perfect for cleaning and removing dirt and mildew stains from decks, patios, walls and siding. Can also be used for disinfectants. All poly construction. Standard with Viton® seals and adjustable nozzle. (1) Gallon capacity. 15” Wand and 41” Hose.

Part No.

Wt.

Backpack Mist Blower is designed for applying plant and tree protection chemicals or for pest and parasite control in animal herds. Creates a fine mist over large areas. Much more efficient than manual spraying. Features: Padded backrest with anti-vibration mounts • 1/2 Gallon fuel tank with low fuel consumption allows for up to 80 minute run time • Chemical tank has 3 gallon capacity • Easy starting, 2-Cycle, 2-1/2 HP engine • Rated to 824 cfm • Application rate is up to 38 ft.

Net Ea.

SL 1201S Handheld Bleach Sprayer 1 Gallon Capacity.... 3 lbs. $ 26.20 5% Discount on 3 or More

D

D

Model 451

Stainless Steel Sprayer Model 465

If your chemical spraying requires stainless steel for compatibility, this is the sprayer you need. An excellent choice for herbicides, pesticides and general purpose spraying. Features: Corrosion-resistant, stainless tank • Plastic shut-off valve • 28” Brass wand • 48” Hose • Brass adjustable nozzle • Extra large handle • 2.25 Gallon capacity.

Part No. D

Wt.

Net Ea.

SL 465 Stainless Handheld Sprayer 2 Gallon Capacity........ 7 lbs. $ 61.95

Model 456-F

Foaming Sprayer

Part No.

SL 451

Unique handheld sprayer is designed to foam chemicals onto horizontal or vertical surfaces. Foam increases dwell time which can increase chemical effectiveness. Can be used with cleaning chemicals, pest control products, mold and mildew cleaners and many more.

Wt.

Net Ea.

24 lbs.

$ 820.00

Automatic Acid Applicator System Complete Applicator System for acid solutions or aggres­ sive chemicals. Ideal for ap­plying aluminum brightener to tractor trailers.

Features: Polyethylene tank • Plastic shutoff valve • Pressure gauge • Foam applicator nozzle • Brass wand • Viton® seals • 2.25 Gallon capacity.

System Includes: Air-op­erated diaphragm pump rated to 2 GPM @ up to 70 PSI • 25 Gallon holding tank • Hydrominder valve for au­tomatic mixing • Trigger spray gun with extension • 75' of 1/4" run tubing • Pump is pre-plumbed to tank and ready for hook-up to your air supply.

D

Part No.

Capacity

Wt.

Net Ea.

SL 456-F

2 Gallon

6 lbs.

$ 66.55

Foam Sprayer.............................

HP

Mist Blower.............. 2-1/2

Part No.

Net Ea.

DU AC1 Acid Applicator System $ 821.00

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E1053


Sprayers

196

Backpack Sprayers Designed to make even the largest spraying jobs manageable. Provides consistent working pressure. Back mounted design features shoulder straps and easy pump handle. Ideal for horticulture, weed control, landscaping and general purpose spraying. High density polypropylene tanks, plastic shut-off valve and wand, nylon reinforced hose. 4 Gallon capacity.

Model 425

Compact Chemical Sprayer Compact, Single Hand Sprayer features polyethylene tank and chemical resistant seals. Ideal for use with a wide variety of solutions. Pest and weed control, carpet spot treating, lubrication and more. Hand pump for pressurization. Nozzle is adjustable from jet to fine mist. Capacity is 1.5 Liter.

D

Model 425 features a piston pump that develops up to 90 PSI.

Part No.

Model 475 features a diaphragm pump rated to 60 PSI and can also be used for wettable powder solutions.

SL 415

Part No.

Capacity

LO 425 LO 475

4 Gallon 4 Gallon

Backpack Sprayer, Piston Pump Backpack Sprayer, Diaphragm Pump

Wt.

Capacity

Wt.

Part No. D

Net Ea.

Handheld Acid Sprayer

Wt.

For difficult acid applications, the handheld 462 Sprayer is the answer. Can be used for masonry cleaning with Muriatic acid, HVAC coil cleaning, wheel cleaners, Phosphoric based cleaners and even hydrochloric solutions.

Model 462

Features: Polyethylene tank • Plastic shut-off valve • 25” Acid-resistant wand • 36” Hose • Adjustable nozzle • Funnel top design • 2.25 Gallon capacity.

Net Ea.

Handheld Sprayer 2 Gallon Capacity....... 4 lbs. $ 24.85 Handheld Sprayer 3 Gallon Capacity....... 6 lbs. 28.90

Part No.

Industrial Sprayers

D

Wt.

Net Ea.

SL 462 Handheld Acid Sprayer 2.25 Gallon Capacity... 4 lbs. $ 46.95 5% Discount on 3 or More

D

Handheld sprayers engineered for the Professional. Rugged design for harsh environments. Ideal for use with weed and pest chemicals as well as degreasers, carpet care products, disinfectants and many other solutions.

Model 456

Model 415

10 lbs. $ 93.95 10 lbs. 94.95

Designed for occasional spraying requirements. General purpose weed and pest control. Can also be used for deck cleaners and mildew removers. 2 and 3 Gallon sizes. Poly tank with durable wand and shut-off valve. Built-in pressure relief valve. Plastic adjustable nozzle. Easy-to-fill funnel top. 19” Wand and 29” Hose.

SL C2G SL C3G

Net Ea.

Hand Sprayer 1.5 Liter 1 lb. $ 7.85 10% Discount on Cartons of 12

Economy Sprayers Model C2G

D

Contractor Series Sprayers

Model 487-CI

Handheld sprayers designed for the construction industry. Ideal for use with curing compounds or Acetones as noted. Hand pump for pressurization but can also be pressurized from air compressor or air tank. High density, polyethylene tanks. 3 Gallon capacity. Nozzle sets for different application rates.

Model 457R with wheels

D

Features: Plastic shut-off valve • Heavy duty pump that pressurizes with less strokes • 4-1/2” Tank opening for easier filling and cleaning • High density, polyethylene tank • Extra long, 48” nylon reinforced hose • 28” Unbreakable wand • Automatic pressure relief valve.

407CI is for use with up to 35% curing compounds. 1/2 and 1 GPM nozzles for curing, form release, sealing and general spraying.Viton® seals, 48” hose and plastic 28” wand are standard. 487CI is for use with Acetone and solvents including alcohols and ammonia. EPDM seals, 72” hose, plastic shut-off, 20” brass wand are standard.

D

Model 457R features wheels for easy transport and 72” hose for remote spraying. Part No.

Capacity

Wt.

Net Ea.

LO 456 Industrial Handheld Sprayer.............. LO 457 Industrial Handheld Sprayer.............. SL 457R Industrial Sprayer with Wheels..........

2 Gallon 3 Gallon 3 Gallon

4 lbs. 7 lbs. 9 lbs.

$ 39.50 44.95 67.50

Part No.

Capacity

Wt.

Net Ea.

SL 407CI Curing/Solvent Sprayer............... SL 487-CI Acetone Sprayer.........................

3 Gallon 3 Gallon

6 lbs. 7 lbs.

$ 62.50 87.95

Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0973


Sprayers

197 “Professional” Series

Compression Sprayer

New Disappearing 5-1/2” Lid

The Professional Series is designed for the professional and features the utmost in performance, comfort and safety. Use for herbicides, insecticides, fungicides, fertilizer, stains, sealers, oil-based and solvent based products. Blow molded tanks are ergonomically designed for comfort. Adjustable extra-heavy padded shoulder straps. 5-1/2” low profile lid with strainer. Patented pumps include high-grade Viton® O-rings and seals for maximum chemical resistance. 20" brass wand, 51" industrial hose & solid stainless steel pump handle; stainless frame and hardware. Adjustable brass nozzle (fan to solid stream); fan and floodjet also. Routine cleaning & maintenance can be done without tools!

Fast, Efficient & Comfortable Backpack Sprayer for All Landscape & Commercial Needs! • Built-In Check Valve in Lid to Prevent Spills from Accidental tipping • Fold-Back Tubular Handle for Easy Storage & Transport

D

• Piston - External Pump Capable of 80 PSI; Diaphragm - Capable of 80 PSI

D

• 5.5” Wide Mouth for Easy Filling & Pouring • 4 Gallon Blow Molded Tank; UV Protection & Viton® O-Rings

Model 100 includes jet agitation for wettable powders & micro-encapsulated products. Model 101 is multi-purpose model; can also spray paints & other viscous products.

Maximum Empty

Part No. Capacity Pressure Pump Type Wt. SX 100 4 Gallon 150 PSI Sealed Piston/Diaphragn 10 lbs. SX 101 4 Gallon 70 PSI Sealed Diaphragm 10 lbs. Other Models Also Available.

• Extra Wide Shoulder Straps • Adjustable Plastic Nozzle, 20” Poly Wand & 43” PVC Hose Part No. SX 302 SX 301

Net Ea. $ 168.00 159.00

302

Description Net Ea. 4 Gallon Backpack Piston Sprayer......... $ 90.00 4 Gallon Backpack Diaphragm Sprayer. 87.00

Acetone/Alcohol Sprayers “Acid & Construction” Series This Series is expressly built to handle the aggressive acids & chemicals of the construction industry. Also use for industrial cleaning/janitorial applications. 20A is specifically designed for spraying muriatic, hydrofluoric & phosphoric acids; acid-based stains and acid-etching products. Use SP35C & 20C for curing compounds, form release agents, form oil, diesel, oil & water-based sealers. 20A includes 4.5" diameter tank mouth; SP35C includes 4.5" “Wide Mouth” feature. Patented pumps and high-grade Viton® O-rings, seals & gaskets for maximum chemical resistance to acids, construction & industrial chemicals. 20" PVC wand on 20A; 20" brass wand on SP35C and 20C. 59" industrial hose on 20A & SP35C. 47" hose on 20C. Fan nozzles.

D

• Large 5-3/8” Wide Opening with Strainer for Easy Filling • 20” Brass Wand with 59” Hose; Adjustable Plastic Nozzle • Pressure Relief Valve up to 40 PSI

SP20ACT

• Convenient Wand Storage Clip in Handle & Large Shoulder Strap

Handles Agressive Acids & Chemicals 20C Acid Sprayer

Specifically Designed for Spraying Acetone & Alcohol

NOTE: Not for chlorine, solvents or degreasers.

D

• Strainer Included

Maximum

Part No. Capacity Pressure Pump Type Empty Wt. Net Ea. SX 20A 2 Gallon 42 PSI 12" Compression 6 lbs. $ 88.95 SX 20C 2 Gallon 42 PSI 12” Compression 6 lbs. 72.00 SX SP35C 3.5 Gallon 42 PSI 12" Compression 8 lbs. 81.00

Part No. SX SP20ACT SX SP35ACT

Description Net Ea. 2 Gallon Acetone Sprayer.............. $ 90.00 3.5 Gallon Acetone Sprayer........... 108.00

Accessories

SERVICE & REPAIRS Did you know? We can service almost every brand of pump we sell in our catalog. Call us at 1-800-228-9666 (Omaha, NE) for a quote!

Part No.

Description Net Ea.

SX KIT300 SX KIT271A SX KIT18FA SX KIT13 SX KIT49.1 SX 284

Spray Pistol, 16" Brass Wand & Nozzle (Universal)................... $ 35.00 PVC Wand & Fittings (for 20A Acid Sprayer)............................... 15.00 Spray Pistol with Filter (for 20A Acid Sprayer)............................. 27.70 Diaphragm Pump Assy Complete (Fits SP1,EK484 & Solo 475)... 49.50 Diaphragm Pump Assembly Complete (Fits SPO)..................... 80.00 Adjustable Heavy Pad Shoulder Straps.................................... 30.00 Viton® is a registered trademark of DuPont Performance Elastomers

DULTMEIER SALES

OMAHA, NE (800)

228-9666

DAVENPORT, IA (800)

553-6975

www.dultmeier.com

E0108


Vacuum Parts & Accessories Dual Service Door Security Cover

198

Vacuum Clean-out Canisters Band Ring

Makes cleaning out vacuums easy. Canisters fit into lower vacuum housing and collect debris. When canister is full, simply lift out and remove debris to your trash bins. Canisters can be used over and over again.

9427K Dual Service Door Security Cover accommodates all J.E. Adams round two-door vacuums, air/vacuums, air/water/vacuums and two door combination units. Protects and covers door latches for new or existing vacuums.

Models 635201 (Doyle & IVS vacu­ums) and DC555 (Doyle, Adams & others) are constructed of a heavy duty collapsi­ble vinyl material with a spring type band. Diameter on these models is 18-1/2" and height is 8" when ex­tended.

9427K Shown on Vacuum

Part-No. Net Ea. AA 9427K Dual Service Door Security Cover for New Vacuums........ $ 118.00 AA 9427K-RETRO Dual Service Door Security Cover for Existing Vacuums... 141.00

D

635201 / DC555

Model DC920 is a heavy duty, molded plastic canister. Diameter is 18-3/4" and height is 8". This model can be used on Doyle, Adams and many other vacuums on the market today.

D

Part-No.

D

Net Ea.

DY 635201 NP DC555 NP DC920

Collapsible Vinyl $ 29.50 Collapsible Vinyl * 11.95 Molded Plastic 25.55

DC920

* Adjustable Band Ring for different requirements. Imported

Lighted Plastic Domes Plastic Domes fit all J.E. Adams vacuums and vacuum combinations. Available in dark green, yellow, white, light green, blue and red. Shipping weight is 6 lbs. (Light Kit is optional).

Power Vac, Doyle & Adams Accessories & Replacement Parts

VACUUM

HANG HOSE HERE

75¢

USE QUARTERS ONLY 8429-1

8429 Decals

8429-4

632904 Filter Bag

D

D

8057 Vac Motor Gasket

D

Part-No. AA 8306 Plastic Domes as Replacements Please Specify Color..................... AA 8543K Light Kit...........................................

Wt. 6 lbs. 2 lbs.

Net Ea. $ 92.55 34.30

8079 Filter Bag Assembly Complete

TRASH CAN ENCLOSURES

TC22 & TC22-S with base

D

Stainless Steel Trash Can Covers are an ideal choice to dress-up your vacuum islands and keep weather out of your trash receptacles. 16-Gauge stainless steel construction. Assemblies come complete with base, dome and rivets. Bases are 28" x 28" with a 13” or 18" opening.

Model TC22-S includes a base and rounded dome that is 8-1/2” high with a 13” opening. Model TC22 includes a base and rounded dome that is 8-1/2" high with an 18” opening. Model TC75 includes a base with a peaked dome that is 36" high and is designed to hold 2 mat clamps on each side. (Mat clamps are also included).

D

TC75

Part No.

NP TC22-S NP TC22 NP TC75

Net Ea.

(800) 228-9666

ACCESSORIES Net Ea. Vac Motor Gasket............................................. $ 1.95 Filter Bag, Adams, 8100/8500.......................... 9.95 Filter Bag, Adams, 9200................................... 14.95 Filter Bag Assembly, Complete, Adams........... 40.95 Lamb Vacuum Motor,116336-01, All................ 49.50 GSE Vacuum Motor, All.................................... 42.95 “Adams” 120-Volt Vacuum Timer...................... 69.65 24 Volt / 110 Volt Timer..................................... 80.95 “GinSan” 110-Volt Timer, IVS........................... 147.00 Fabric Filter Bag, Doyle / IVS .......................... 16.80 Vac Door Gasket, Adams................................. 5.36 Door & Motor Gasket Kit, IVS........................... 28.00 Door Latch with clip, Power Vacuum, IVS........ 16.75 Door Latch, Adams.......................................... 15.05 Pin Lock, All..................................................... 11.80 Hang Hose Decal............................................. 1.90 $.50 Vacuum Decal.......................................... 2.15 $.75 Vacuum Decal.......................................... 1.90 $1.00 Vacuum Decal........................................ 2.30

Replacement Motors Shown in the Vacuum Motor Section.

Trash Can Cover with round dome, 13”..... $ 139.00 Trash Can Cover with round dome, 18”..... 139.00 Trash Can Cover with peaked dome......... 479.00

DULTMEIER SALES • OMAHA, NE

Part-No. AA 8057 AA 8072 AA 8076 AA 8079 DY 105100 AA 8095 AA 8712SS4 IX AT411E GS GS403 DY 632904 AA 8159 DY DVK100 DY 622001 AA 8153 DY 635200 AA 8429-1 AA 8429-3 AA 8429-4 AA 8429-5

8153 Door Latch

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0648


Vacuums

199

• Top grade 18 gauge stainless steel construction • 19" Diameter x 54" High. • Rust-free anti-jam coin acceptor. (“Sensortron” or “Slugbuster” mechanisms available at added cost). • Pin-lock security system for added protection. • 2" x 15' Hose with claw (Choice of Colors). • Rated to 200 CFM & 90" Waterlift (2 motor vacs). • Vault Ready Models are also available.

• Unique 4 Filter System for increased motor life. • One-piece Dome Design to prevent leakage (Stainless or Poly). • (2) or (3) 1.6 HP Motors. • Exterior Channel to totally enclose supply wiring. • 110 Volt, 20 Amp (2 motor) or 30 Amp (3 motor) Ratings. 220 Volt also available. • Upper Access Door For Filter Clean-Out. • Lower Cleanout Door for Easy Cleaning.

Standard S.S. Dome

Plastic Lighted Dome Vacuums

Stainless Dome Vacuums 2-Door Stainless Steel Vacuums from JE Adams!

2-Door Poly Lighted Dome Vacuums from JE Adams! NOTE: Lighted domes available in Red, Blue, Yellow, Green or White.

Choose from different decal options! F.O.B. Factory

F.O.B. Factory

D

Cleanout Door

9200 with Small Stainless Dome & Standard Decal Set

Large S.S. Dome

D

9210LD & 9213LD with Poly Dome & Standard Decal Set

D

D

9200-1LD Digital with Poly Dome & Bill Acceptor

9210 & 9213 with Large Stainless Dome with Optional Rainbow Hose

D

9200-4 with S.S. Dome

Coin-Operated Vacuums with Poly/Lighted Domes Part No. AA 9210LD 2 Motor Vacuum, Poly Dome, Coin Acceptor, 110 Volt................... AA 9213LD 3 Motor Vacuum, Poly Dome, Coin Acceptor, 110 Volt................... AA 9200-5LD 3 Motor Vacuum, Poly Dome, Coin Acceptor & Digital Display, 110 Volt. AA 9200-1LD 2 Motor Vacuum, Poly Dome, Coin Acceptor, Bill Acceptor, Digital Display, 110 Volt..............................

Coin-Operated Vacuums with Stainless Domes

Wt.

Net Ea.

150 lbs.

$ 1245.00

150 lbs.

1298.00

157 lbs.

1998.00

159 lbs.

2245.00

DULTMEIER SALES • OMAHA, NE

(800) 228-9666

Part No. AA 9200 2 Motor Vacuum, Small SS Dome, Coin Acceptor, 110 Volt........................ AA 9200-4 2 Motor Vacuum, Small SS Dome, Coin Acceptor, Digital Display, 110 Volt AA 9210 2 Motor Vacuum, Large SS Dome, Coin Acceptor, 110 Volt........................ AA 9213 3 Motor Vacuum, Large SS Dome, Coin Acceptor, 110 Volt........................ AA 9200-5 3 Motor Vacuum, Large SS Dome, Coin Acceptor, Digital Display, 110 Volt

www.dultmeier.com

• DAVENPORT, IA

Wt.

Net Ea.

150 lbs.

$ 1197.00

152 lbs.

1950.00

152 lbs.

1279.00

155 lbs.

1350.00

155 lbs.

2070.00

(800) 553-6975

E0010


Vacuums • Air Machines

“Power Vac” Stainless Vacuums

Model 10000T with Toggle On/Off Switch

Model 140000

200

Super Suction, Sure-Start Vending, Largest Filter System, Lock-in Security: “Power Vac” vacuums have it all. • Dual powered with two 1.6 HP motors • Four-filter design features the industry’s largest filter area • Upper filter access door for quick maintenance • Electronic Timer for price & time flexibility • Armored “pin-lock” protects from thieves, weather and vandals • Colorful decal and design. (Different decal colors available).

Filter Door

“Power Vac” Vacuums are available in three different models for your choosing: Model 140000:

Coin-op - Brushed Stainless Steel Housing & Dome.

Model 1000DM: Coin-op - Brushed Stainless Steel Housing with *Poly D

Dome & Light Kit .*(Specify from red, blue, teal, white, yellow & green).

Model 10000T:

Toggle Switch operated, Brushed Stainless Steel Housing & Dome. (No Timer).

D

Cleanout Door

Power Specifications (standard equipment)

Standard Features: Stainless Steel housing, 18-gauge, 304SS • Stainless steel or Polyethylene Domes • Upper filter door for easy access to filters • (4) Filter design • (2 or 3) 1.6 HP, Lamb motors • 2" x 15' hose • Solid-state IDX electronic timers • Drop-style coin mechanism with coin return • Lower clean-out door for dirt removal • ETL Approved • 12-gauge stainless vault box.

Vacuum Motors: Lamb, two stage, by-pass cooled motors, 7 amp (oper. avg., each) Input: 15 amp, 120 VAC/60 Hz (20 amp. circuit required) Airflow: Net 160 CFM (open), 84” H20 (static) Timer: Electronic, Dual outputs, 1 to 255 coins, 2 sec. to 8.5 min. per coin Acceptor: Mechanical with coin return & catcher Filters: 4 bags, 15 sq. feet total area, two access doors Hose: Hi-flex, crushable hose, 2 in. by 15 ft. with tool Tank: 18 Gauge, 304 Stainless Steel with hand-brushed finish, tank 18” x 42” (H) Vaults: 12 Gauge 304 Stainless steel - Recessed door Electrical Connection: Integral connection cover, removable for easy access and installation. 20 amp, 120 VAC service required Mounting: Three mounting lugs for 1/2” bolts. Opt’l. bracket available Dimensions: 54” (H) x 24” (D) x 20” (W) Ship: 57” (H) x 24” (D) x 24” (W). Tank: 18-1/2” O.D., S/S Dome: 20” O.D. Poly Dome: 21-1/2” O.D. Weight: 105 lbs. net, Ship: 135 lbs.

Part No. DY 140000 SS Coin-Op Vacuum, 2 Motor DY 100000-3 SS Coin-Op Vacuum, 3 Motor DY 1000DM Poly Dome Coin-op Vacuum DY 10000T Toggle Switch Vacuum D

— F.O.B. Factory — Model 1000DM

Air/Vacuum Combo

Air Machines

— Double Door —

A combination Air/Vacuum in one unit. Ideal for car washes, convenience stores, truck stops or any highly travelled area. This model features top grade 18-gauge stainless steel that will hold its lustrous finish year after year. Your money is safe in a 10gauge stainless high security box with a completely concealed pin lock for added protection. Standard with (2) coin mechanisms so that both services can be offered to separate customers at the same time. Standard with (2) Doors - Upper door for filter access and lower door for trash removal. D

TIRE INFLATOR SPECIFICATIONS Air Compressor: Oil-less motor mounted, dual cylinder, thermal protection, safety valve. Hose: 1/4" I.D. x 25 ft., cut-resistant wire braid. Pressure: Up to 90 PSI.

Specifications: Two 1.6 HP vacuum motors • 19" diameter canister • 54-1/2" Height • Weight is 175 lbs. • 115 volt • 1.5 HP air compressor motor delivers up to 90 psi • 25' air hose with gauge and valve • 15' x 2" vacuum hose with cuff.

Stainless Steel Air Machines are a great addition to your convenience store, truck stop or car wash. Tough stainless steel construction and good engineering ensures years of dependable service. Constructed of a high quality 14-gauge stainless steel. These machines have an attractive design and will look like new year after year. Units available with or without base. Designed with a concealed hinge and high security lock bar system that has been engineered to protect your income. An optional locking coin box allows service to the mechanics of the equipment without access to the money.

D

#8670-2GA Machine Only

#8533-8 Air Chuck

Specifications: 1.5 HP oilless, 3.1 SCFM at 90 PSI Compressor • Timer is adjustable up to 10 minutes and 1 to 7 coins • Gauge is heavy-duty bayonet style • Hose is cut resistant 25' x 1/4" wire braid. • Dimensions are 18" W x 16" H x 12-1/2" D.

#8647 Nozzle

D

#8670-2WBTA-65 Machine with base

Part No. Net Ea.

AA 8670-2GA AA 8670-2WGA AA 8670-2FGA

Part No. Net Ea.

AA 9420-1G * Air/Vacuum Unit $ 2049.00

DULTMEIER SALES • OMAHA, NE

Wt. Net Ea. 140 lbs. $ 1529.00 135 lbs. 1575.00 152 lbs. 1498.00 135 lbs. 1075.00

Pay Air Machine, Wall Mount..................... $ 1389.00 Pay Air/Water Machine, Wall Mount........... 1529.00 Free Air Machine, Wall Mount.................... 1339.00

AA 8670-2BA/6026 Pay Air Machine with S.S. Base & Reel............. AA 8670-2WBTA-65 Pay Air/Water Machine with S.S. Base & Reel..

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

2150.00 2550.00

E0009


Specialty Vacuums

201 Commercial Vacuums

Vacuum / Scent Combo Unit

With On-Off Switches

D

9225 & 9235-3 Vacuums are designed with heavy-duty toggle switches for On/Off control. Features: (2 or 3) 1.6 HP motors • 110 Volt operation • Lower trash clean-out door • Upper filter access door • (4) Filters • Stainless Steel construction. 9235LD Vacuum same as 9225 but with lighted poly dome. (Specify Dome Color - see following page). 9225X Vacuum features push button switch and timeout option that shuts down the vacuum if left on. Stainless steel dome.

Vacuum, Fragrance option in one machine. Features: (2) 1.6 HP Motors • Mars bill acceptor • Multi-coin, electronic coin mechanism • (2) Service doors for easy maintenance and access • Digital timer with readout • Last coin alert • Lighted domes in red, blue, yellow, dark green, light green and white.

Part No. Motors Wt. Net Ea. AA 9225 Commercial Vacuum, Toggle 2 140 lbs. $ 1085.00 AA 9235-3 Commercial Vacuum, Toggle 3 140 lbs. 1298.00 AA 9235LD Commercial Vacuum, Toggle 2 140 lbs. 1085.00 AA 9225X Commercial Vacuum, Timeout 2 140 lbs. 1085.00

D

Part No. Wt. Net Ea. AA 8900 Fragrance / Vacuum Unit, Coins & Bills....... 190 lbs. $ 3960.00 AA 8900L Fragrance / Vacuum Unit, Coins Only......... 190 lbs. 3605.00

Tire Shine Vacuum Machine

Combo Vacuum/Shampoo Machine

D

A Great Revenue Source from J.E. Adams! Combination Vacuum and Tire Shine Unit. Features premium, allseason Tire Shine formula. Gives customers a long lasting shine for their tires, just spray on and let dry. Standard Features Include: (3) 110 Volt motors • Digital Timer Display • Last coin alert • Lighted pushbutton functions • Lighted domes in a variety of color options • (4) Filter bags • 2” x 15’Vacuum hose with swivel cuff and nozzle • 1-Gallon Tire Shine chemical • Available in coin only or coin/ bills acceptance, (Mars bill validator). Note: Units are available with credit card acceptance option also.

With Spot Remover

D

Model 9500

High quality Combo Vacuum/Shampoo Machine from J.E. Adams. Increases revenue for you and increases customer satisfaction. Stainless canister with a Poly Dome in the color of your choice. Light kit is also standard. Standard Features: Mars Bill Acceptor Validator • Electronic Coin Mechanism accepts up to 4 different coins or tokens • (2) 1.6 HP Vacuum Motors • Digital Count Down Timer with last alert • (4) Filter Bag System • Pin Lock Style Coin Box • 1 Gallon Start Up Shampoo & Spot Remover • 15' Vacuum Hose with cuff • 15' Shampoo Hose with scrub brush • 54-1/2" high x 30" wide • Weight is 190 lbs.

Part No. Wt. Net Ea. AA 9500 Vacuum/Shampoo Machine, Coins & Bills. 250 lbs. $ 3798.00 AA 9501 Vacuum/Shampoo Machine, Coins Only.... 190 lbs. 3505.00 AA 95W 1 Gallon All Season Formula Shampoo...... - 19.30 AA 11000SPOT Spot Remover Formula.............................. - 22.55

Part No. Wt. Net Ea. AA 29037 Tire Shine Vacuum Machine, Coins Only... 260 lbs. $ 4798.00 AA 29035 Tire Shine Vacuum Machine, Coins/Bills... 260 lbs. 5098.00 AA 29035-10 1 Gallon Tire Shine Refill........................... - 40.05

Dual Hose Kit A great option to JE Adams Vacuums. Most JE Adams Vacuums can be ordered with the Dual Hose Kit as an option. This allows the customer to use the standard vacuum claw or easily switch to the 1-1/2” crevice tool. Vacuums ordered with this option will come with two hoses and hose hangers as well as the changeover valve. This option is for new vacuums only and is not available for existing units in the field. Crevice tool and hose are only available in black. Standard 2” claw and hose are available in different colors.

9210OLD Vacuum shown with Optional 4015KIT Dual Hose Adapter, 2” Claw Nozzle, and 1-1/2” Crevice Tool

D D

4015KIT

Part No. Net Ea. AA 4015KIT Dual Hose Kit, New Vacuum ADD-ON..... $ 315.50 DULTMEIER SALES • OMAHA, NE

(800) 228-9666

www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0688


Combo Vacuums Carpet Wizard

202 Vacuum Combo Units

Carpet Wizard Vacuum/Carpet Shampoo / Spot Remover Machine. Combination machine for added revenues and customer satisfaction. Customers can easily change from vacuum to carpet shampoo to spot remover option during the same cycle. High quality, stainless construction. Available with or without Mars bill acceptor. Standard with (2) Two-stage vacuum motors.

• ULTRA secure 2-door design separates service area from individually locked bill acceptor & coin box storages areas providing protection for your investment. • ULTRA maximum security with (7) Medeco locks (3 for control door, 1 for internal bill acceptor locking box, 1 for internal coin locking box, and 2 for bottom service compartment). • Built with many common industry standard components. • Easy-to-use lighted push buttons clearly identify selected service. • Lighted colored domes in Red, Blue, Yellow or Dark Green. • Highly visible, easy-to-read large digital display timer scrolls messages, calculates time between functions, recalculates remaining time when switched during any function, built-in coin counter. • Electronic multi coin acceptor & visual, audible last coin alert. • Coinco 2000 bill acceptor takes $1 & $5 bills. • 3 - 1.6 HP motors and (4) Quick change filter bags. • Optional credit card acceptor & alarm system available. • Startup Chemicals.

D

Standard Features on all Combo Units Electronic Multi-Coin Acceptor • Digital Display Timer with Last Alert • Lighted, Illuminated Domes • Eye-Catching Graphics • Scrolling Message Display • Service Areas are Separate from Money Vault for Added Security • Money Vault Features Two-Door Security • Coin Counter for Quick Coin Audits • (4) High Capacity Filter Bags • 2” x 15’ Hose • 16 Gal. 304SS Construction • 120 Volt, 20 Amp Rating • 61” H x 22” W x 27” D • Startup Chemicals Included • Choice of Dome & Hose Colors (Red, Blue, Yellow or White) D

Fresh’N Up Vacuum / Fragrance Machine. Combination machine that allows customer to choose from (3) fragrance options or vacuum mode during the same cycle. High quality stainless construction. Available with or without Mars bill acceptor. Standard with (2) two-stage vacuum motors.

Ultra Turbo-Nator® Shampoo & Spot Remover Combination Vacuum Models 29000, 29001, 29002, 29003

D

Ultra Turbo-Nator® Fragrance Combination Vacuum Models 29015, 29016, 29017, 29018

D

Ultra Turbo-Nator® Vacuum Models 29060, 29061, 29062, 29063

Shampoo & Spot Remover Combination Vacuum 29000 2 motor vacuum, 3 motor turbo vacuum, shampoo & sport remover, with bill acceptor, 260 lbs. 29001 2 motor vacuum, 3 motor turbo vacuum, shampoo & spot remover, with bill acceptor, vault ready, 260 lbs. 29002 2 motor vacuum, 3 motor turbo vacuum, shampoo & sport remover, no bill acceptor, 260 lbs. 29003 2 motor vacuum, 3 motor turbo vacuum, shampoo & spot remover, no bill acceptor, vault ready, 260 lbs. Fragrance Combination Vacuum 29015 2 motor vacuum, 3 motor turbo vacuum, 3 fragrances, with bill acceptor, 260 lbs. 29016 2 motor vacuum, 3 motor turbo vacuum, 3 fragrances, with bill acceptor, vault ready, 260 lbs. 29017 2 motor vacuum, 3 motor turbo vacuum, 3 fragrances, no bill acceptor, 260 lbs. 29018 2 motor vacuum, 3 motor turbo vacuum, 3 fragrances, no bill acceptor, vault ready, 260 lbs.

D

Fragrance / Shampoo / Vacuum Units 29060 3 motor vacuum with turbo option, Fragrance, Shampoo, Spot Remover. Includes coin and bill acceptors. Standard with coin drawer. 298 lbs. 29061 3 motor vacuum with turbo option, Fragrance, Shampoo, Spot Remover. Includes coin and bill acceptors. Vault ready design. 298 lbs. Part No. Description Wt. Net Ea. 29062 3 motor vacuum with turbo option. Fragrance, Shampoo, Spot Remover. Coin acceptor only with coin drawer. 298 lbs. DY 51007 Carpet Wizard, Coins only.................... 333 lbs. $ 4389.00 29063 3 motor vacuum with turbo option. Fragrance, Shampoo, Spot Remover. DY 51003 Carpet Wizard, Bills & Coins................. 333 lbs. 5005.00 Coin acceptor only, vault ready design. 298 lbs.

DY 50007 DY 50003

Fresh’N Up Machine, Coins Only.......... 333 lbs. Fresh’N Up Machine, Bills & Coins....... 333 lbs.

DULTMEIER SALES • OMAHA, NE

4389.00 5106.00

(800) 228-9666

— Call for Current Pricing — www.dultmeier.com

• DAVENPORT, IA

(800) 553-6975

E0728


Vacuum Islands

203

A great way to take your vacuum business to the next level and upgrade your facilities at the same time. Available with and without canopies (single vacuum only, single vacuum with trash enclosure or double vacuum with trash enclosure). Standard with 14 gauge, Stainless Steel construction for great looks and longer life. (Vacuums are not included). Heavy-duty plastic bumper guards are included with all models. All islands are designed to be filled with concrete on site. Economy islands are stainless frame only. Concrete fill creates base and support for vacuums. Optional Trash Enclosures on economy units are stainless construction and are shown below.

Economy Vacuum Islands Model 35VC with TC75 Enclosure

Model 12VC: Single island is 36" x 36" x 24" high