Page 1

X Series Centaurs In-grade ETL Listed Wet Label IP68

CX 2/14 79 Trenton Avenue Frenchtown, NJ 08825

www.designplan.com

Tel: (908) 996-7710 Fax: (908) 996-7042


C1X

In-Ground LED Fixture

IP68

Series C1X

Lamp L-LED

. Cast stainless steel body 304 alloy . 1W Cree XPE LED . On-board electronics for 24V DC and 0-10V dimming . Unique “bottle cap” threaded lens frame . No screws to lose . Lens frame turned from solid stainless steel . 0.400” thick tempered glass lens . Walkover, drive over rated for 11,000 lbs at 30 mph . Cast stainless steel 304 alloy junction box . Silicone rubber anti siphon outlet box gasket . Remote power supply . Unit can be through wired for daisy chaining . Class II, not suitable for fountain or pool use. . Requires remote 24V Dc power supply . Available in RGB with remote DMX controller

Wattage 1L-1x1W 3000K LED 3L-1x1W 5000K LED

Body 4-Fully recessed w/cond. entries

listed wet label IP68

Color Temp. SS-Stainles Steel

Note: Other color available

Optic Ballast 0- None X-120vAC-24vDC 1- 6 Degree Spot Remote Driver 2- 25 Degree Flood

Note: LED Optics are for use with 'T' clear glass lens. They are not intended for 'K' or 'G' Lenes

Lens Options 0-None T-CLR. Temp Glass K-Internally Ceramic Coated Tempered Glass G-Frosted Toughened Glass

Note: On board 0-10v Dimming

Power Supplies SERIES

C1X

DRIVER PART #

PPLT00155 PPLT00157 PPLT00158

Designplan Lighting

DESCRIPTION

120VAC-24VDC 30W 120VAC-24VDC 60W 120VAC-24VDC 100W

WATTAGE

1W 24vDC w/ integral 0-10v dim 1W 24vDC w/ integral 0-10v dim 1W 24vDC w/ integral 0-10v dim

UNITS POWERED

SPECIAL DETAILS

1 to 24 1 to 48 1 to 80

parallel parallel parallel


Staten Island 911 Memorial

Lighting Consultant: Fisher, Marantz, Stone

Fixture: C1X

Designplan Lighting


. Cast stainless steel body 304 alloy . 1W Cree XPE LED . On board electronics for 24V DC and 0-10V Dimming . Unique “bottle cap” threaded lens frame . No screws to lose . Lens frame turned from solid stainless steel . 0.400” thick tempered glass lens . Walkover, drive over rated for 11,000 lbs at 30 mph . Cast stainless steel 304 alloy junction box . Silicone rubber anti siphon outlet box gasket . Remote power supply . Unit can be through wired for daisy chaining . Class II, not suitable for fountain or pool use. . Requires remote 24V Dc power supply . Available in RGB with remote DMX controller listed wet label IP68

C2X

In-Ground 24V Dimmable LED Fixture

IP68 Remote Driver Series C2X

Lamp L-LED

Wattage Body 1L-1x1W 3000K LED 4-Fully recessed 2L-1x1W 4000K LED w/cond. entries 4L-1x3W 3000K LED 5L-1x3W 4000K LED Note: Other colors available on request

Finish SS-Stainless Steel

Optic 0- None 1- 10 Degree Narrow 2- 21 Degree Medium 3- 39 Degree Wide 4- 10x44 Degree Elliptical Note: LED Optics are for use with 'T' clear glass lens. They are not intended for 'K' or 'G' Lenes

Ballast X-Remote 24vDC Transformer Required

Lens T-Clear Temp Glass K-Internally Ceramic Coated G-Frosted Tempered Glass

Options 0-None

Note: On board 0-10v Dimming

Power Supplies C2X 1 LED/UNIT

PPLT00155

120VAC-24VDC 30W

PPLT00157

120VAC-24VDC 60W

PPLT00158

120VAC-24VDC 100W

Designplan Lighting

1W 24vDC w/ integral 0-10v dim 3w 24vDC w/ integral 0-10v dim 1W 24vDC w/ integral 0-10v dim 3w 24vDC w/ integral 0-10v dim 1W 24vDC w/ integral 0-10v dim 3w 24vDC w/ integral 0-10v dim

1 to 10 1 to 6 1 to 19 1 to 13 1 to 32 1 to 22

parallel parallel parallel parallel parallel parallel


. Cast stainless steel body 304 alloy . 3x 3W Cree XPE LED . On board electronics for 24V DC and 0-10V dimming . Unique “bottle cap” threaded lens frame . No screws to lose . Lens frame turned from solid stainless steel . 0.400” thick tempered glass lens . Walkover, drive over rated for 11,000 lbs at 30 mph . Cast stainless steel 304 alloy junction box . Silicone rubber anti siphon outlet box gasket . Remote power supply . Unit can be through wired for daisy chaining . Class II . Requires remote power supply listed wet label IP68

C4X

In-Ground 24V Dimmable LED IP68 Remote Driver Series C4X

Lamp L-LED

Wattage 1R-3x1W White 3000K 2R-3x1W White 4000K 3R-3x3W White 3000K 4R-3x3W White 4000K

Body 4-Fully recessed w/cond. entries

Finish SS-Stainless Steel

Other colors available upon request

Optic 0- None 1- Narrow (6°) 3- Wide (25°) 4- Elliptical (6°x25°)

Ballast Q-Remote 24vDC Driver Required (Int. 0-10V Dim.)

Remote Driver to be ordered separately

Lens T-Clear Temp Glass J-Flash White BTM & Non-Skid Top Pattern K-Flash White BTM & Clear Top G-Internally Frosted Toughened Glass Q-Non-Skid Top Patterned Tempered Glass

Options 0-None

Power Supplies C4X 3 LED'S PER UNIT

PPLT00155

120VAC-24VDC 30W

PPLT00157

120VAC-24VDC 60W

PPLT00158

120VAC-24VDC 100W

1W 24vDC w/ integral 0-10v dim 3w 24vDC w/ integral 0-10v dim 1W 24vDC w/ integral 0-10v dim 3w 24vDC w/ integral 0-10v dim 1W 24vDC w/ integral 0-10v dim 3w 24vDC w/ integral 0-10v dim

1 to 6 1 to 2 1 to 13 1 to 5 1 to 22 1 to 8

parallel parallel parallel parallel parallel parallel

Designplan Lighting


. Cast stainless steel body 304 alloy . Cree MCE LED . On board 24vDC with DMX interface individually controlled . Unique “bottle cap” threaded lens frame . No screws to lose . Lens frame turned from solid stainless steel . 0.400” thick tempered glass lens . Walkover, drive over rated for 11,000 lbs at 30 mph . Cast stainless steel 304 alloy junction box . Silicone rubber anti siphon outlet box gasket . Remote power supply . Unit can be through wired for daisy chaining . Class II, not suitable for fountain or pool use . Available anti slip dot pattern glass lens . DMX channels are not field addressable without specialized equipment. If addresses are not specified, the fixture will default to address 1 (1-red, 2-green, 3-blue, 4-white). listed wet label IP68

C4C

In-Ground LED Fixture

IP68 Remote Integral Driver Series C4C

Lamp L-LED

Wattage 3K-5W RGBW LED 4K-5W Dynamic White

Body 4-Fully recessed w/cond. entries

Finish SS-Stainless Steel

PPLT00155 PPLT00157 PPLT00158

Designplan Lighting

Options 0-None

Remote Power Supply.

Power Supplies C4C 1 CREE MCE per unit

Lens Ballast T-Clear Temp Glass X-Remote 24vDC Power Supply Req'd J-Flash White BTM & (INT DMX INTERFACE) Non-Skid Top Pattern K-Flash White BTM & Clear Top Note: Integral 24vDC Driver G-Internally Frosted Board along with individually Toughened Glass controlled DMX interface Q-Non-Skid Top Patterned To be used with Tempered Glass

Optic 0- None 1- Narrow (10°) 2- Med (30°)

120VAC-24VDC30W 120VAC-24VDC 60W 120VAC-24VDC 100W

4.6w 24vDC w/ int. DMX interface 4.6w 24vDC w/ int. DMX interface 4.6w 24vDC w/ int. DMX interface

1 to 4 1 to 9 1 to 16

parallel parallel Parallel


. Cast stainless steel body 304 alloy . 6x 1W Cree XPE LED . Integral power supply for 120V non-dimming . Available in MR16 12V DC halogen with integral power supply . Unique “bottle cap” threaded lens frame . No screws to lose . Lens frame turned from solid stainless steel . 0.400” thick tempered glass lens . Walkover, drive over rated for 11,000 lbs at 30 mph . Cast stainless steel 304 alloy junction box . Silicone rubber anti siphon outlet box gasket . Remote power supply . Unit can be through wired for daisy chaining . Class I . Available anti slip dot pattern glass lens

C7X

In-Ground Fixture Flat Trim IP68

Series C7X

Lamp 6-Halogen L-LED 9-HID

Wattage 14-37W MR16 NSP10 15-37W MR16 NSP25 16-37W MR16 FL40 1F-1Wx6 Ring 3K White LED AM-1Wx6 Ring 5K White LED 2F-1Wx6 Ring Red LED 3F-1Wx6 Ring Blue LED 4F-1Wx6 Ring Green LED 5F-1Wx6 Ring Cyan LED 6F-1Wx6 Ring Amber LED AG-20W MH GE MR16 Spot 3000K AH-20W MH GE MR16 Flood 3000K

Body 4-Fully recessed w/cond. entries

listed wet label IP68

Finish SS-Stainless Steel

Note: MR16 Lamps mounted to adjustable swivel bracket tilt max 15° off vertical.

Grill 1- STD

Ballast T-120V-12V Elect. Integral Trans. J-277V-12V Elect. Integral Trans. C-120V-277V Elect. Integral Trans.

Lens G-Internally Frosted Toughened Glass U-Non Skid Temp Glass T-Clear Temp Glass

Options 0-None

Note: Halogen is either T or J. LED is always C and comes standard with 0-10V dimming. HID metal halide is always C.

Designplan Lighting


. Cast stainless steel body 304 alloy . Xicato 1300lm LED module with integral driver for 120-277V w/ 0-10V Dimming or . 20W MR16 MH adjustable with integral ballast . Unique “bottle cap” threaded lens frame . No screws to lose . Lens frame turned from solid stainless steel . 0.400” thick tempered glass lens . Walkover, drive over rated for 11,000 lbs at 30 mph . Unit can be through wired for daisy chaining . Class I . Available anti slip dot pattern glass lens listed wet label IP68

CDX

In-Ground Fixture

Flat Trim IP68 Series CDX

Lamp 9-HID L-LED

Wattage AG-20W MH GE MR16 Spot 3000K AH-20W MH GE MR16 Flood 3000K FB-39W MH GE MR16 Spot 3000K FC-39W MH GE MR16 Flood 3000K EX-1300lm Xicato 3000K EY-1300lm Xicato 3500K EZ-1300lm Xicato 4000K AG, AH, FB, FC HID Only EX, EY, EZ LED Only

Designplan Lighting

Body 4-Fully recessed w/cond. entries

Finish SS-Stainless Steel

Grill 1- STD

Ballast C-120-277V Integral Electronic L-120-277V w/ Integral 0-10V Dimming Ballast 'C' HID Only Ballast 'L' LED Only

Lens T-Clear Temp Glass Q-Non Skid Temp Glass Patterened

Options 0-None W-Linear Spread Q-Honeycomb Louver S-Solite Lens B-Special Lens (see drawing) Note: Options added to rubber holder.


Drawings C1X

C2X

Designplan Lighting


Drawings C4X

C4C

Designplan Lighting


Drawings C7X

CDX - LED

Designplan Lighting


General Installation Instructions 11/2/07

FAILURE TO FOLLOW THESE INSTRUCTIONS WILL VOID WARRANTY RISK OF ELECTRICAL SHOCK. THIS EQUIPMENT IS TO BE INSTALLED BY A QUALIFIED ELECTRICIAN ONLY. MAKE CERTAIN ELECTRICAL SUPPLY CIRCUIT IS DE-ENERGIZED BEFORE BEGINNING INSTALLATION. CHECK FIXTURE LABEL FOR CORRECT VOLTAGE. READ ALL INSTRUCTIONS CAREFULLY. LOCATION This model is designed for concrete pour installation. The upper edge of the housing must be flush with the prepared surface into which it is recessed. Do not install fixture in a manner that creates a pocket where water can sit on top of fixture. Not suitable for use in places where the luminaire is likely to be exposed to a horizontal stress load caused by braking, acceleration or change of direction. INSTALLATION 1. Lighting fixture comes fully assembled. Note: When not working on fixture replace trim ring for site safety and to protect fixture components from moisture and damage. Keep each trim ring with the original body it was supplied on. Note: Use care to protect O-ring on trim ring. Do not remove, loosen, cut, deform or otherwise disturb O -ring. Keep Oring clean and dry. 2. Set fixture in desired location. Position the fixture in such a manner that the conduit/cable is not stressed at the entry point to the light fixture. 3. The foundation on which the luminaire is to be installed must correspond to the maximum permissible pressure load of the luminaire. Suitable drainage must also be provided. Level the body in two horizontal planes using the three leveling tabs around outer body. The upper edge of the housing must be flush with the prepared surface into which it is recessed. UNDER NO CIRCUMSTANCES MAY IT BE LOWER! 4. Unthread lens assembly from body with tool provided. Ensure that all internal surfaces of the fixture are kept completely dry during installation. Pry out the accessory gasket by using a screw driver. Carefully by hand remove reflector. 5. Connect incoming leads to quick disconnect plug. GREEN WIRE TO “GROUND”, CONNECT BLACK FIXTURE TO BLACK BUIDLING WIRE AND CONNECT WHITE FIXTURE WIRE TO WHITE BUILDING WIRE. Replace tray, lamp, and reflector. Make sure that no wires have been damaged. 6. If using conduit entries, the entries must be sealed with “Dap Heavy Duty Kwik Foam” (not provided). The foam should be sprayed from inside the fixture up into the conduit. Failure by the contractor to use the DAP product could cause a void in the warranty. Replace tray with lamping. If not using through wiring, plug second conduit entry with 3/4" conduit plug. Please make sure wet label requirements are meet. 7. Install lamp and adjust if necessary. Tighten all screws to assure the lamp will not shift after aiming is acquired. Replace reflector and accessory gasket. 8. Place lens frame over fixture ensuring that there is no foreign matter between the lens frame and the body. Start the lamp and bring luminaire to operating temperature (20 to 30min.), this will evaporate the moisture content of air to be trapped. Once operating temperature has been reached, carefully thread the trim assembly to body with tool provided.

DESIGNPLAN LIGHTING, INC., 79 TRENTON AVE, FRENCHTOWN, NJ 08825 T. 908-996-7710 F. 908-996-7042 79 Trenton Avenue Frenchtown, NJ 08825

www.designplan.com

Tel: (908) 996-7710 Fax: (908) 996-7042

X Series Centaur  
X Series Centaur  

Cast stainless steel in grade uplights for LED, Halogen and Metal Halide