Issuu on Google+

Premium Stainless Steel Maintenance and Repair Electrode Enhanced Chromium-Nickel Stainless Steel Electrode.

StainTrode D ®

ELECTRODES • Welding dissimilar stainless steels • Welding stainless steels to carbon steels • Welding stainless steels of unknown composition • High heat applications


DESCRIPTION

TYPICAL ANTI-WEAR APPLICATIONS & INDUSTRIES

StainTrode D is an enhanced chromium-nickel electrode formulated to weld dissimilar stainless steels and stainless steels of unknown composition. Its chemistry is enriched for use with AISI grade 310. This premium stainless steel electrode is easily handled and has very good scaling and oxidation resistance up to 2100° F.

APPLICATIONS

INDUSTRY

• Boiler Baffles • Sponge Iron Kilns • Radiant Tubes • Annealing Covers • Refractory Anchor Bolts

Various Industries Iron and Steel Works Iron and Steel Works Iron and Steel Works Cement Works

WELDING PROCEDURE & TECHNIQUE

STAINTRODE D TECHNICAL DATA TeroMatD6t-up Information & SET-UP INFORMATION

Preparation: Clean weld area of scale and/or oxide. Make sure all oily contaminants are removed with a suitable VOC-free cleaner. Angle prepping normally involves closebutts and infrequently bevel preparations. If needed, a 60° V bevel is acceptable. Pre-heating of stainless steels is generally not required. Technique: A short, non-contact technique is recommended for both fillet and butt-welding. Use a slightly longer arc-length for bead-on-plate welding. Deposit stringer beads or 2 times to 3 times weave beads. Do not weave more than three times the electrode diameter otherwise excessive heat input will cause distortion. Post-Welding: Allow parts to cool naturally in still air.

Typical Tensile Strength: Typical Yield Strength: Typical Elongation: Typical Hardness: Typical Impact Strength: Typical Ferrite Content:

95,000 psi (655 N/mm2) 64,000 psi (440 N/mm2) 35% at room temperature BHN: 190 Charpy V: 35 ft-lbs at -150°F Fully austenitic

WELDING PARAMETERS Current & Polarity: Diameters: Amperage:

AC or DCEP (+)

3/32" - 2.4mm

1/8" - 3.2mm

5/32" - 4.0mm

85 - 105

115 - 135

65 - 80

Note: When using StainTrode D, keep to the low-end of the amperage range for optimized results.

YOUR RESOURCE FOR PROTECTION, REPAIR AND JOINING SOLUTIONS Eutectic Corporation

Eutectic Canada

Eutectic Mexico

N94 W14355 Garwin Mace Drive Menomonee Falls, WI 53051 USA P 800-558-8524 • F 262-255-5542 www.eutectic-na.com

52 Hymus Blvd. Suite 220 Pointe-Claire, Quebec H9R 1C9 Phone: (800) 361-9439 Fax: (514) 695-8793 www.eutectic-na.com

KM 36.5 Autopista Mexico-Quertaro 54730 Cautitlan-Izcalli Estado de Mexico, Mexico Phone: 011 (52) 55-5872-1111 e-mail: eutectic.mexico@eutectic.com.mx

Statement of Liability: Due to variations inherent in specific applications, the technical information contained herein, including any information as to suggested product applications or results, is presented without representation or warranty, expressed or implied. Without limitation, there are no warranties of merchantability or of fitness for a particular purpose. Each process and application must be fully evaluated by the user in all respects, including suitability, compliance with applicable law and non-infringement of the rights of others, and Eutectic Corporation and its affiliates shall have no liability in respect thereof. staindDS-05-22-07


StainTrode-D