Page 1

PP-1-22-GPM PPP-1-22-GPM

OWNER’S MANUAL PressurePak II & PressurePak III Systems

www.pressurepak.com Copyright © 2008 by PressurePak, Inc. Patent Pending


WARRANTY CARD Model # ____________ Serial # ________________________ Purchase Date _______________________________________ Owner’s Name ______________________________________ Address ____________________________________________ City _________________ State ______ Zip _______________ Place of Purchase ____________________________________ This card must be returned within ten (10) days of purchase. Please fill out and return to: PressurePak 925 Freedom Blvd #444 Watsonville, CA 95076

PRESSUREPAK™ Technical Data Flow: Max. 40 GPM (9 CMH) Head: Max. 300 feet/130 PSI (91 M) Fluid Temperature: Max. 95 degrees F (0 degrees C) Ambient Temperature: Min. 32 degrees F (0 degrees C) Operating Pressure: Max. 145 PSI Inlet Pressure: Min. flooded suction, Max. limited by operating pressure Operating Setpoint: 40 to 100 PSI (in 10 PSI increments) Sound Pressure Level: Ext. installation < 74 dB(A) at 3 feet from pump With enclosure: Various depending on enclosure type and insulation Construction: Stainless steel pump casing and plumbing installed in a weather-proof galvanized steel box System Configurations Base Setup includes a 15 GPM variable speed (PP-1-22-GPM) constant pressure pump capable of producing up to 70 PSI of additional water pressure, a variable speed pump controller (PP-1-22GPM), a 2 gallon pressure tank and a power cut-off box, all in a galvanized steel box. Upgrades are available including dual pump systems that meet flow standards for residential sprinkler system. PLEASE READ BEFORE INSTALLATION WARNING: Before beginning any installation procedures, these installation and operating instructions should be studied carefully. The installation and operation should also be in accordance with local regulations and accepted codes of good practice.

www.pressurepak.com Copyright © 2008 by PressurePak, Inc. Patent Pending


INSTALLATION:

Each system comes ready to plug in (plug and play) either 110v or 220v which ever system you have. Installation Kits are available for the “in” and “out” water lines. PP-1-22-GPM

Electronic Controller

Congratulations on your purchase of the PressurePak Water Boosting System!

C B PPP-1-22-GPM

Hydraulic Controller

C B Optional Installation Kit Includes:

(1) 1 1/2” intake ball valve. This valve is to be connected to your water source IE water holding tank. B (1) 1 1/2” outtake ball valve. This valve is connected to your line running to the water use IE your home. C (1) Hose Bib note: Hose Bib must be installed before and above the outtake ball valve.

LIMITED WARRANTY PressurePak water system units manufactured by Pressurepak, Inc. are warranted to the original user only to be free of defects in material and workmanship for a period of eighteen months (18) from the date of installation. The electric pressure pump installed within the PressurePak unit has additionally warrantee offered by PressurePak Inc. for a five year (5) period from date of installation at an additional cost. PressurePak’s liability under this warranty shall be limited to repairing or replacing at PressurePak’s option, without charge, F.O.B. PressurePak factory any PressurePak product. PressurePak Inc. will not be liable for any costs or removal, installation, transportation, or any other charges which may arise in connection with a warranty claim. PressurePak Inc. will not be liable for damage or wear to PressurePak units caused by abnormal operating conditions, accident, abuse, misuse, unauthorized alteration or repair, or if the PressurePak unit was not installed in accordance with PressurePak printed installation and operating instructions. To obtain service under this warranty, the defective PressurePak unit must be returned to the distributor or dealer of PressurePak from


which it was purchased together with proof of purchase and installation date, failure date and supporting installation date. Unless otherwise provided, the distributor or dealer will contact PressurePak Inc. for repair instructions. Any defective PressurePak unit to be returned to PressurePak Inc. must be sent freight prepaid; documentation supporting the warrant claim must be included if so instructed. PRESSUREPAK INC. WILL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSSES OR EXPENSES ARISING FROM INSTALLATION, INCLUDING MERCHANTABILITY OR FITNESS FOR A PARTICULAR PUPOSE, WHICH EXTEND BEYOND THOSE WARRANTIES DESCRIBED OR REFFERED TO ABOVE. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages and some jurisdictions do not allow limit actions on how long implied warranties may last. Therefore, the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from jurisdiction to jurisdiction. Any questions or inquiries regarding this warranty or any PressurePak water system products may be directed to PressurePak Inc., 925 Freedom Blvd., Watsonville, California 95076; Telephone (831) 786-9976; Fax (831) 722-2276.

CHARACTERISTICS The three most important characteristics of the PRESSUREPAK™ Systems: 1. Plug and play design enables simple installation with three connections: a. Low pressure water pipe “IN” hook-up b. Hi pressure water pipe “OUT” hook-up c. Electrical connection d. 110 15 Amp, 3 Amp U ground plug e. 220 20 Amp, 3 prong twist-lock plug 2. Variable speed (PP-1-22-GPM), submersible, constant pressure pump technology: a. Performance proven reliability b. Greater flow curves at lower power consumption c. Soft start which prevents water hammer d. Relatively quiet operation 3. Everything in one box engineering makes it possible to solve complex water pressure problems in one service call. SIZING GUIDE 1. Determine approximately how much water pressure you have available at your water inlet. 2. Determine how much water pressure you require at maximum flow. 3. The pressure difference between you available pressure (1 above) and your required pressure (2 above) is the PSI Boost Needed for you.

PPak Owner's Manual  

ppak owner's manual

PPak Owner's Manual  

ppak owner's manual

Advertisement