Issuu on Google+

PRODUCT INFO

PARAMETERS OF PASS DOORS

59

SPECIFICATION Overview of pass door positions Summary of basic dimensions

Dear customer, In this Product Info we offer you general information on pass doors in TOORS sectional doors, including a review of possible positioning within the door leaf.

Dimensions limits for door with pass door Recommendations regarding door accessories

Door parameters Maximum door width with a pass door is 6 000 mm. Maximum surface of a door leaf with a pass door is 30 m2 (this is valid for a door leaf without aluminium – FVE – sections or for a door leaf with maximum three FVE sections). Maximum surface of a door leaf with a pass door including more than three FVE sections is 22 m2 (this is also valid for a door where all sections are FVE).

Pass door parameters The absolute through width of a pass door within the door leaf is 875 mm. The through height of the door is approx. 2 040 mm (measured from the 2 040 floor; this height may be different 875 in a door with FVE sections in order to maintain the same height of all FVE sections). The above through height of a pass door may be maintained only if the sectional door is at least 2 250 mm high. The height of the pass door threshold is approx. 200 mm. The pass door with a low threshold (about 80 mm in industrial doors, about 65 mm in garage doors) can be supplied up to the door width of 3 500 mm. The actual through height and the threshold height of a pass door depends on the type and range of compression of the bottom sealing rubber (when the sectional door is closed).

TECHNICAL SPECIFICATION Door Door leaf without aluminium – FVE – sections or with maximum three FVE sections Maximum door width

6 000 mm

Max. surface of a door leaf

30 m2

Door leaf including more than three FVE sections Maximum door width

6 000 mm

Max. surface of a door leaf

22 m2

Pass door Absolute through width

875 mm

Through height

2040 m2*

Height of standard threshold

200 mm

Height of low threshold - industrial doors - garage doors

80 mm 65 mm

* Only if the sectional door is at least 2 250 mm high


OPTIONS Bottom bar (door with pass door)

Bottom bar For industrial doors with a pass door the bottom section of which is made of a panel, the so-called high bottom bar is always used (natural aluminium, 100 mm high). For garage doors this bar is used for door width W ≥ 4 000 mm and for doors with a low threshold. For garage doors closer than 4 000 mm with a standard threshold a bar 40 mm high is used. Sensor for open pass door detection We recommend always fitting a pass door with a sensor for open pass door detection, even if operated manually. The door with a pass door with an operator must always be provided by this type of sensor. Additional sensor mounting (in case of need to change the manual operation to motor control) is technically demanding and requires disassembling of the bottom section.

Industrial doors High bottom bar

100 mm*

Garage doors W ≥ 4 000 mm or doors with a low threshold High bottom bar 100 mm Garage doors W ≤ 4 000 mm Low bottom bar

40 mm

* For industrial doors with the bottom section made of a panel

Strut within the door leaf The door including a pass door should be provided at least by one strut within the door leaf. This strut is recommended to be mounted directly above the pass door (on the 4th section). Due to added strut the rigidity of the fourth section will be increased that was reduced by cutout for the pass door. Positioning of windows The pass door may include windows only in the 2nd and 3rd sections. Positioning of a window in the 1st and 4th sections is not possible for technical reasons. Opening of the pass door The pass door in the sectional door can be opened only outwards. Opening of the pass door in the direction inwards is not possible for technical reasons – the complete weight of the pass door would lie only on the snap-bolt of the door lock after moving the door leaf into the horizontal part of the rails. A self opening of the pass door could cause a damage of the whole door leaf. Positioning of pass door hinges

left door right door (door view from inside)

For clear identification of positioning of pass door hinges when viewed the door from inside, it should be always specified, if the given pass door is a left pass door (it has hinges on the right when viewed from inside), or a right pass door (it has hinges on the left when viewed from inside).

If you have any questions concerning this PRODUCT INFO, do not hesitate to contact the company TOORS.

ATTENTION ! It is not possible to install a pass door into all types of panels. More information can be found in Panel range offer for TOORS Indy and TOORS Guardy. A part of this Product Info is an enclosed review of possible positioning of pass doors within the door leaf dependent on door width. Other dimensions and positioning can be provided on request.

www.toors.com

TOORS CZ s.r.o., Turkova 1338, 504 01 Nový Bydžov, Czech Republic, Tel.: +420 495 491 855, Fax: +420 498 606 714, e-mail: toors@toors.cz


Door blade without aluminium sections (only from panels) Door width 1 500 mm – 2 990 mm, 2 fields This pass door can’t have the hinges on the right side (handle on the left side)!

1st field (1-2) in the middle (M-2)

Door width 3 000 mm – 3 990 mm, 3 fields This pass door can't have the hinges on the right side (handle on the left side)!

1st field (1-3)

Door width 4 000 mm – 4 990 mm, 4 fields This pass door can't have the hinges on the right side (handle on the left side)!

1st field (1-4)

2nd field (2-4)

Door width 5 000 mm – 5 990 mm, 5 fields

2nd field (2-5)

Door width 6 000 mm, 6 fields 2nd field (2-6)

3rd field (3-6)

2nd field (2-3)

2nd field (2-2)

3rd field (3-3)

in the middle (M-4)

3rd field (3-5)

in the middle (M-6)

This pass door can't have the hinges on the left side (handle on the right side)!

This pass door can't have the hinges on the left side (handle on the right side)!

3rd field (3-4)

4th field (4-4)

This pass door can't have the hinges on the left side (handle on the right side)!

4th field (4-5)

4th field (4-6)

5th field (5-6)

The views on the Doors are from the interior side.

TOORS CZ s.r.o, Turkova 1338, 504 01 Nový Bydžov, Czech Republic Tel.: +420 495 491 855, fax: +420 495 491 853, e-mail: toors@toors.cz

TOORS CZ s.r.o., Turkova 1338, 504 01 Nový Bydžov, Czech Republic, Tel.: +420 495 491 855, Fax: +420 498 606 714, e-mail: toors@toors.cz

www.toors.cz www.toors.com


Door blade with min. 1 aluminium section Door width 1 500 mm – 2 500 mm, 2 fields

1st field (1-2)

This pass door can't have the hinges on the right side (handle on the left side)!

Door width 2 510 mm – 3 750 mm, 3 fields This pass door can't have the hinges on the right side (handle on the left side)!

Door width 3 760 mm – 4 750 mm, 4 fields This pass door can't have the hinges on the right side (handle on the left side)!

1st field (1-3)

1st field (1-4)

Door width 4 760 mm – 5 750 mm, 5 fields

Door width 5 760 mm – 6 000 mm, 6 fields 2nd field (2-6)

2nd field (2-3)

2nd field (2-4)

2nd field (2-5)

2nd field (2-2)

3rd field (3-3)

3rd field (3-4)

3rd field (3-5)

3rd field (3-6)

This pass door can't have the hinges on the left side (handle on the right side)!

This pass door can't have the hinges on the left side (handle on the right side)!

4th field (4-4)

This pass door can't have the hinges on the left side (handle on the right side)!

4th field (4-5)

4th field (4-6)

5th field (5-6)

The views on the Doors are from the interior side.

TOORS CZ s.r.o, Turkova 1338, 504 01 Nový Bydžov, Czech Republic Tel.: +420 495 491 855, fax: +420 495 491 853, e-mail: toors@toors.cz

TOORS CZ s.r.o., Turkova 1338, 504 01 Nový Bydžov, Czech Republic, Tel.: +420 495 491 855, Fax: +420 498 606 714, e-mail: toors@toors.cz

www.toors.cz www.toors.com


Gönguhurðir í flekum indy guardy