Page 1

® Installation  Guide     CO2LIGHT

Contents

1. Tubes 2. Panels 3. Downlight 4. Streetlight

CO2LIGHT®      Gørtlervej  21        DK-­‐9000  Aalborg        Phone:  +45  70  70  15  55        e-­‐mail:  info@co2light.com  


® Installation  Guide   CO2LIGHT  

LED Tubes  

Begin the  installation  by  shutting  off   the  power.  

Identify what  kind  of  ballast,  you  are   using  (magnetic  or  electronic)  

Magnetic ballast:   Remove  the  old  starter,  and  either   remove  or  bypass  the  magnetic   ballast.  Only  for  specific  demo  and   test  uses,  the  ballast  can  be  left  in.     In  any  case,  the  phase  compensation   capacitor  should  be  removed.  

Electronic ballast:   Remove  the  old,  electronic  ballast.  

Adjust the  pins  by  the  rotating   caps,  and  insert  the  tube  in  the   fixture.  Remember,  that  the   power  should  go  to  the  end   that  says  ”power”.  It  should   also  be  noted  that  the  fixture   should  be  marked  according  to   what  end  the  power  comes   from       CO2LIGHT®        Gørtlervej  21        DK-­‐9000  Aalborg        Phone:  +45  70  70  15  55        e-­‐mail:  info@co2light.com  


® Installation  Guide   CO2LIGHT

LED Panels  –  Wire  Installation   Unpack  the  enclosed  driver.  

Connect the  driver’s  brown  cord  (L)     and  the  blue  cord  (N)  with  the  spark   plug.    

Insulate the  connection  point.  Most   electricians  use  cable  sleeves  with   insulation.  If  in  doubt,  contact  your   electrician.  

Connect the  DC  end  of  the  cord  to  the   panel.  

CO2LIGHT®        Gørtlervej  21        DK-­‐9000  Aalborg        Phone:  +45  70  70  15  55        e-­‐mail:  info@co2light.com  


® Installation  Guide   CO2LIGHT

LED Panels  –  Ceiling  Assembly   Fasten  the  frame  securely  to  the   ceiling.  Note,  that  the  screw  is  going   to  carry  the  frame,  the  panel  and  the   driver.    

Inser the  panel  within  the  frame  

Connect the  driver  before  completing   the  frame.  Use  the  enclosed  plugs.   Hide  the  driver  behind  the  panel.   Connection  to  230V  AC  should  be  in   accordance  with  the  specific  laws.  

Mount and  secure  the  last  piece  of   the  frame.  

Mound and  secure  the  last  piece  of   the  frame  

CO2LIGHT®        Gørtlervej  21        DK-­‐9000  Aalborg        Phone:  +45  70  70  15  55        e-­‐mail:  info@co2light.com  


® Installation  Guide   CO2LIGHT

LED Panels  –  Wall  Assembly   Fasten  the  frame  securely  to  the  wall.   Note,  that  the  screw  is  going  to  carry   the  frame,  the  panel  and  the  driver.    

Do not  mount  the  last  piece  of  the   frame  yet.  

Insert the  LED  panel  within  the  frame  

Connect the  driver  before  completing   the  frame.  Use  the  enclosed  plugs.   Hide  the  driver  behind  the  panel.   Connection  to  230V  AC  should  be  in   accordance  with  the  specific  laws.    

Mount and  secure  the  last  piece  of   the  frame  

CO2LIGHT®        Gørtlervej  21        DK-­‐9000  Aalborg        Phone:  +45  70  70  15  55        e-­‐mail:  info@co2light.com  


® Installation  Guide   CO2LIGHT

LED Panels  –  Suspended  Assembly  

Fasten the  wire  to  the  frame    

Do a  two-­‐point  mounting  

Mount it  to  the  ceiling,  with  the  same   distance  between  the  wires  as  on  the   panel  

Adjust to  spirit  level.  

CO2LIGHT®        Gørtlervej  21        DK-­‐9000  Aalborg        Phone:  +45  70  70  15  55        e-­‐mail:  info@co2light.com  


® Installation  Guide   CO2LIGHT  

LED Downlight  

Begin the  installation  by  drawing  a   circle  on  the  ceiling,  where  to   downlight  is  going  to  be.  The  diameter   of  the  circle  kan  be  found  in  the   catalogue  (measurement  B).  Use  a   saw  or  some  other  tool  to  cut  out  the   circle  as  shown  in  the  figure.  

Attach the  power  supply  to  the   ceiling,  and  connect  the  ac-­‐cable  to   the  high-­‐tension  cable.     Note  that  it  should  be  possible  for  the   power  supply  to  cool  off  

Connect the  DC-­‐output  to  the   downlight  

Install the  lamp,  by  pressing  on  the   clamps,  and  pushing  it  into  the  hole  in   the  ceiling.  

CO2LIGHT®        Gørtlervej  21        DK-­‐9000  Aalborg        Phone:  +45  70  70  15  55        e-­‐mail:  info@co2light.com  


® Installation  Guide   CO2LIGHT  

LED Streetlights  

Link the  terminal  plugs  of  the   streetlight  and  the  terminal  block    in   the  pole  (brown  to  brown,  blue  to   blue,  yellow  to  yellow  and  green  to   green).  Then  close  the  PC  cover  after   linking  the  plugs  securely.  Lastly  put   the  terminal  block  wiring  back  into   the  pole.  Always  use  officially   approved  assembly  units  (isolated).  If   you  are  in  doubt,  contact  your   electrician.  

Loosen the  screws  on  the  lamp,  and   connect  it  to  the  pole  

Fasten the  screws,  and  thereby   finalize  the  connection  with  the  pole.  

CO2LIGHT®        Gørtlervej  21        DK-­‐9000  Aalborg        Phone:  +45  70  70  15  55        e-­‐mail:  info@co2light.com  

Installation Guide  

An installation guide to the CO2LIGHT products

Read more
Read more
Similar to
Popular now
Just for you