Page 1


ASGARD 'FREESTORE' PACK CONTENTS

5

4

3

2

1

44162 LH FRNT SIDE PNL 1834*1092

44161 RH REAR SIDE PNL 1834*1107

44160 LH REAR SIDE PNL 1834*1107

44159 RH BACK PNL 1979*777

44158 LH BACK PNL 1979*760

44157 FRONT TOP PNL 1570mm*1112mm

44156 REAR TOP PNL 1570mm*1130mm

1

1

1

1

1

1

1

1

ITEM PART QTY NO DESCRIPTION

6

44163 RH FRNT SIDE PNL 1834*1092

7 8 1

44290 EXT BASE PNL 1518*1103

1

1

1

1

1

15

5

2

16

1

4

9

SEALENT

3

EXTERNAL CENTRE WELD

ZSCREW61

No10*5/8 S/TAPP

QTY 295

PACKERS

2 EA

17

10

12

8

14

ZSCREW32

NO HOLES IN THIS FACE INDICATE FRONT OF PNL ZSCREW340

9

M5*12 CSK ST/ST M7.5*60 ANCHOR BOLT

18

6

ZCOMPPLAS 22,23,24

7

NO HOLES IN THIS FACE INDICATE FRONT OF PNL

ZCOMPPLAS02

12

SELF SEAL PLUG

11

12

SELF ASSEMBLY INSTRUCTIONS

18

EXTERNAL CENTRE WELD

1

16

44291 LH EXT SIDE 1834*1107 44293 EXT TOP PNL 1570mm*1110mm

17 1

15

1

1

44292 RH EXT SIDE 1834*1107

1

44166 REAR BASE PNL 1518*1100

44376 RH FRONT PNL 1862*385 44167 FASCIA PNL 787*220

44374 DOOR ASSEMBLY 1733*780

44378 FRONT BASE PNL 1092*1518 44164 LH FRONT PNL 1862*385

9 10 11 12 13 14

13

ASGARD

ASGFS1533###

PLEASE NOTE FOR SAFETY REASONS THE ASSEMBLY OF THIS UNIT REQUIRES TWO PEOPLE. BASE INSTRUCTIONS A FIRM, LEVEL ,FLAT SURFACE IS REQUIRED AS A BASE FOR THIS UNIT SUCH AS CONCRETE OR FLAGS. - MINIMUM BASE MEASUREMENT (ALLOWS FOR RAMP) 1730W*3740D)

TOOLS REQUIRED - POSI-DRIV SCREWDRIVER (POWER DRIVER RECOMMENDED)

- 6mm DIA MASONRY DRILL - 13mm SOCKET SPANNER (FOR ANCHOR FIXINGS)

- A TUBE OF ALL WEATHER SEALENT SUITABLE FOR STEEL AND CONCRETE.

DOOR ALLIGNMENT & ANCHORING OF UNIT

IT IS IMPORTANT TO CORRECTLY LEVEL THE UNIT USING THE PACKING PIECES PROVIDED, ONCE ASSEMBLY IN ACCORDANCE WITH THE INSTRUCTIONS OVERLEAF IS COMPLETE AND PRIOR TO FIXING THE UNIT TO THE GROUND.

- SLIDE THE PACKING PIECES UNDER THE CORNERS OF THE UNITS BASE AS REQUIRED UNTIL AN EQUAL GAP HAS BEEN ACHIEVED AROUND THE DOORS ALLOWING FOR THEIR SMOOTH OPERATION & ALLIGNMENT.

- DRILL THROUGH THE FOUR HOLES IN THE BASE OF THE UNIT USING 6mm DIA MASONRY DRILL TO A DEPTH OF 70mm. - SCREW IN THE ANCHOR FIXINGS. (THESE HAVE A SELF CUTTING THREAD)

IF NOT ANCHORING THE UNIT USE THE SELF SEAL PLUGS TO BLOCK THE FIXING HOLES (FIT FROM UNDERSIDE)

IF FITTING THE OPTIONAL RAMP IT IS ADVISED THAT THIS IS POSITIONED PRIOR TO BUILDING THE UNIT.

PLEASE SEE OUR WEBSITE FOR DETAILS OF MAINTENANCE OF THIS PRODUCT WWW.ASGARDSSS.CO.UK 044383


STEP 1

PARTS FRONT BASE - 10 EXTEN BASE PANEL -18 REAR BASE -9

26* STEP 5

SLOT INDICATES BACK OF REAR BASE PANEL

9 18 10

INSTRUCTION POSITION REAR BASE PANEL '9' , EXTENSION BASE '18' & FRONT BASE ' 10' AS SHOWN ENSURING THAT THE PANELS ARE LINKED TOGETHER ALONG THE CENTRAL JOINTS AND THE HOLES ARE ALIGNED, SCREW TOGETHER.

INSTRUCTION

5

PARTS

LOCATE LH REAR SIDE PANEL '5' INTO THE BASE & LH BACK AS SHOWN ENSURING THAT HOLES ARE ALIGNED SCREW TOGETHER ALONG THE BASE AND VERTICAL JOINTS.

LH REAR SIDE PANEL -5

19*

INSTRUCTION

STEP 2

PARTS POSITION RH BACK PANEL '4' AS SHOWN LOCATING THE CENTRE FLANGE ON THE BACK IN THE SLOT ON THE REAR OF THE BASE PANEL, ENSURE HOLES ARE ALIGNED AND SCREW TOGETHER.

4

RH BACK PANEL - 4

STEP 3

PARTS RH REAR SIDE -6

6

INSTRUCTION

POSITION REAR RH SIDE PANELS '6' UP TO THE PRE ASSEMBLED BASE AND BACK ENSURING THAT IT LOCATES AROUND THE RH BACK PANEL AND SLOTS INTO THE CENTRAL BASE JOINT.ENSURE HOLES ARE ALIGNED AND SCREW TOGETHER.

STEP 4

PARTS

LH BACK PANEL - 3

19*

(THE BACK WILL REQUIRE SUPPORTING UNTIL THE SIDE PANEL AS BEEN ATTACHED)

22*

22*

SEALENT

LH EXTENSION SIDE PANEL - 16

PARTS

3*

17

ALIGN HOLES AND SCREW TOGETHER ALONG THE VERTICAL AND HORIZONTAL JOINTS.

ATTACH RH EXTENSION SIDE '17' TO RH REAR SIDE AND BASE, THE PANEL SHOULD BE LEVEL WITH THE FRONT OF THE BASE PANEL.

INSTRUCTION

STEP 8

22*

RH EXTEN SIDE PANEL - 17

PARTS

STEP 7

1

APPLY SEALENT HERE

APPLY A BEAD OF SEALENT DOWN THE FULL LENGTH OF THE VERTICAL JOINT OF THE RH REAR SIDE PANEL PRIOR TO FITTING THE RH EXTENSION SIDE.

LIFT REAR ROOF PANEL '1' ONTO THE ASSEMBLED PARTS ENSURE THAT THE FRONT OF THE ROOF SITS LEVEL WITH THE SIDE PANELS, (THE ROOF WILL ONLY FIT ONE WAY) ALIGN HOLES AND SCREW TOGETHER.

INSTRUCTION

STEP 6

PARTS REAR ROOF PANEL -1

SEALENT

16*

3

INSTRUCTION

LOCATE LH BACK PANEL '3' INTO THE BASE & RH BACK AS SHOWN ENSURING THAT THE CORNER JOINT IS CORRECTLY ALIGNED ALONG WITH THE FIXING HOLES.

APPLY A CONTINOUS BEAD OF SEALENT ALONG THE FULL LENGTH OF THE ROOF JOINT.

SCREW TOGETHER ALONG THE BASE AND VERTICAL JOINT.

16

SEALENT

INSTRUCTION

REPEAT STEP 7 WITH LH EXTENSION SIDE '16' APPLYING SEALENT DOWN THE VERTICAL JOINT OF LH REAR SIDE PRIOR TO FITTING THE PANEL.

044383

IMPORTANT PRIOR TO FITTING THE EXTENSION ROOF (STEP 9) APPLY A CONTINOUS BEAD OF SEALENT AS INDICATED ALONG THE FULL LENGTH OF THE ROOF CHANNEL


STEP 9

PARTS EXTENSION ROOF PANEL - 15

SEALENT

22*

PARTS LH FRONT PANEL - 11

SEALENT

18*

2

INSTRUCTION

APPLY SEALENT HERE

LIFT EXTENSION ROOF PANEL '15' INTO POSITION ENSURING THAT THE CENTRAL FIXING JOINT IS FULLY LOCATED INTO THE REAR ROOF PANEL, FORCING THE SEALENT INTO THE JOINT TO SEAL IT, ENSURE THE HOLES ARE ALLIGNED AND SCREW TOGETHER. APPLY A BEAD OF SEALENT DOWN THE FULL LENGTH OF THE VERTICAL JOINT OF THE RH EXTENSION SIDE PANEL PRIOR TO FITTING THE RH FRONT SIDE.

11 INSTRUCTION

REPEAT STEP 13 WITH LH FRONT PANEL '11'

STEP 10

PARTS RH FRONT SIDE PNL -8

SEALENT

24*

PARTS FASCIA PANEL -8

8*

INSTRUCTION

8

SEALENT

ATTACH RH FRONT SIDE '8' TO RH EXTENSION SIDE AND BASE, THE PANEL SHOULD BE LEVEL WITH THE FRONT OF THE BASE PANEL. ALIGN HOLES AND SCREW TOGETHER ALONG THE VERTICAL AND HORIZONTAL JOINTS.

14

APPLY A CONTINOUS BEAD OF SEALENT ALONG THE FULL LENGTH OF THE ROOF JOINT.

IMPORTANT PRIOR TO FITTING THE RH FRONT PANEL STEP '13' APPLY A BEAD OF SEALENT WHERE INDICATED.

SEALENT INSTRUCTION ATTACH THE FASCIA PANEL '14' TO THE LEFT AND RIGHT HAND FRONT PANELS AS SHOWN, POSITION IT SO THAT IT RUNS IN LINE WITH THE TOP OF THE FRONT PANELS. ALIGN HOLES AND SCREW TOGETHER IMPORTANT PRIOR TO FITTING THE FRONT ROOF PANEL APPLY A CONTINUOUS BEAD OF SEALENT AS INDICATED

STEP 13

PARTS

RH FRONT PANEL - 13

18*

PARTS FRONT ROOF PANEL -2

30*

INSTRUCTION

13

POSITION THE RH FRONT PANEL '13' ON TO THE FRONT OF THE BASE AS SHOWN SLIDE THE PANEL UP TO THE SIDE PANEL SO THAT THE INNER FIXING FLANGE LOCATES AROUND THE FOLDS ON THE SIDE.

ENSURE THE HOLES ARE ALLIGNED AND SCREW TOGETHER THIS SHOULD SQUEEZE THE APPLIED BEAD OF SEALENT INTO THE CORNER JOINT TO SEAL.

2

INSTRUCTION

LIFT THE FRONT ROOF PANEL '2' INTO POSITION ENSURING THAT THE OUTER WELDED JOINT IS TO THE FRONT OF THE ROOF AND THE CENTRAL FIXING JOINT IS FULLY LOCATED INTO TO REAR ROOF PANEL, FORCING THE SEALENT INTO THE JOINT TO SEAL IT.

ENSURE THE HOLES ARE ALLIGNED AND SCREW TOGETHER.

STEP 14

PARTS

LH FRONT SIDE PANEL -7

24*

PARTS

DOOR - 12

9*

7

INSTRUCTION

REPEAT STEP 10 WITH LH FRONT SIDE '7' APPLYING SEALENT DOWN THE VERTICAL JOINT OF LH EXTENSION SIDE PRIOR TO FITTING THE PANEL.

12

INSTRUCTION

SEAL INTERNAL BASE CORNERS

WE RECOMMEND THAT YOU USE HAND HELD DRIVERS RATHER THAN POWER DRIVERS WHEN FIXING THE DOOR. IT IS IMPORTANT TO SUPPORT THE DOOR AT ALL TIMES WHEN FITTING THE SCREWS TO ENSURE CORRECT ALIGNMENT AND SO NOT TO DAMAGE THE THREADED INSERTS.

ALIGN THE HINGES OF DOOR '12' AND SCREW IN POSITION. SEE PAGE 1 WITH REFERENCE TO CORRECT DOOR ALIGNMENT AND LEVELLING PROCEDURE.

044383

HAVING LEVELLED THE UNIT, USE THE SEALENT TO SEAL ALL 12 INTERNAL CORNERS OF THE THREE BASES.


044529

2. POSITION TWO FLOOR PANELS IN THE EXTENSION BASE (1533 UNIT ONLY) . THESE PANELS SHOULD BE POSITIONED SO THERE IS AN EQUAL SPACE TO THE FRONT AND BACK OF THE STEEL BASE PANEL.

1. POSITION TWO FLOOR PANELS IN THE REAR BASE OF YOUR UNIT AND PUSH THEM AS FAR BACK AS POSSIBLE.

3. REMOVE SCREWS FROM THE TOP OF THE BASE JOINT ONLY. POSITION INFILL STRIP SO THE HOLES ARE ALLIGNED WITH THE HOLES IN THE BASE JOINT AND THE EDGES SLOPE DOWNWARD. REFIT THE REMOVED SCREWS FIXING THE STRIP BACK IN POSITION. USE 14 SCREWS FROM YOUR FITTING KIT TO SCREW INTO THE WOOD FLOOR PANELS TO HOLD IN PLACE.

ASGARD FLEXISTORE 1522 AND 1533 FLOOR FITTING INSTRUCTIONS FIT FLOOR PANELS HAVING BOLTED DOWN THE UNIT AND ALSO HAVING FITTED THE OPTIONAL RAMP IN ACCORDANCE WITH THOSE INSTRUCTIONS. 1533 UNIT (3 BAY) IS SHOWN KIT CONSISTS OF: - 6 FLOOR PANELS - 2 INFILL STRIPS - 1 FITTING KIT. 1522 UNIT (2 BAY) KIT CONSISTS OF - 4 FLOOR PANELS - 1 INFILL STRIP - 1 FITTING KIT.

2. 1POSITION TWO FLOOR PANELS IN THE FRONT BASE OF YOUR UNIT AND PUSH THEM AS FAR FORWARD AS POSSIBLE. (TOWARDS THE FRONT OF YOUR UNIT)

REMOVE SCREWS FROM THE TOP OF THE BASE JOINT AND FOLLOW STEP 3 FOR INFILL STRIP FITTING.

Flexistore Large Metal Shed Instructions  

Flexistore Large Metal Shed Instructions

Read more
Read more
Similar to
Popular now
Just for you