Issuu on Google+

A L U M I N U M

H O R S E

S T A L L S

8 0 0 - 8 7 6 - 7 7 0 6

Sliding Stall Doors • Stall Fronts • Gossip Gates • Stall Dividers • Shutters • Double Dutch Doors End Barn Doors • Window Grilles • Vent Panels • Miniature Stalls • Stall Accessories • Construction Brackets


Stall Front Details Door Hardware is Included in our Prices! The stall front is made up of two major components, the stall grille and the stall door. Sliding doors are recommended because they allow adequate aisle space for individuals to lead horses out of the inside stall area. The remaining stall front, not including the sliding door, is usually made up of a lower solid lumber or concrete wall and a top grille. Grilles are available with or without the Feeder Access Door which allows for easy food distribution without entering the stall. Stall Front Details: For simple lumber construction- It is necessary to have three or four posts across the front of each stall. Three posts are used if building fronts with the door at one end (pictured) and four posts are used if centering door (not pictured) is the end goal. For three post fronts, place one vertical post at each stall end usually 10´0˝ or 12´0˝ on center. Second, sink the third post 4´0˝ (inside to inside post measurement) from one end. Similarly, for centered door space, place two posts 4´0˝ from one another. Once posts are in place you have three options for the stall front wall: 1. Mount boards to the front of the posts 2. Recess the lumber flush between the posts or 3. Purchase an Armour Stall Front Wall Panel. See pictures 1,2, & 3 below. Mounting lumber to the face of the posts is the easiest and most economical. Recessing boards flush between the posts can be accomplished using Receiver Channel (4a-4b). When one of the above two options are chosen, build stall walls up approximately 4´0˝ leaving an additional opening height of 3´0˝ or 4´0˝ between the top of the stall wall and the bottom of the header area, for the stall front grille.

1

2

3

4a

4b

4c

RC4 Receiver Channel 46-1⁄2 ˝

Slide lumber into “U˝ shaped channel to assist in building stall divider walls and foaling stalls. Channels arrive with ventilation weep holes installed, fasteners and predrilled mounting holes.


Sliding Door & Grille Door Hardware is Included in our Prices!

Our Standard Bar Top may be ordered with a Fold-Down or Lift-Out Panel. Cap Reinforcement tops each door to prevent dust and vermin from being collected.

This self-cleaning and aligning, round galvanized Overhead Door Track and Ball-bearing Trolley Set is easy to glide and it even prevents pests from nesting. The round track shape enables closer contact with the trolley system and installed doors open easy unlike, square track. Fasteners for lumber installation are included for mounting track.

Full Height Vertical Reinforcements line the outer door edge for rigidity & strength.

Armour features standard safe 3˝ between bar spacing with 1˝ diameter pickets on all doors and grilles. 2˝ and 1˝ between bar spacing is available upon request with an additional charge.

All grilles are constructed using our unique concealing technique which leaves no unsightly welds. All door and stall front grilles are welded at the top and bottom, so pickets will not pop out or rattle. With Armour Components, there are no loose pieces to assemble and all aluminum is at least 1⁄8˝ thick minimum.

A Zinc Plated Super Latch, Receiver Plate, and Receiver Stop Set are provided. Doors arrive prepared for latching, upon request, at No Additional Cost.

⁄8˝ vs. 1⁄16˝ thickness.

1

Channel protects all four edges of lumber door panel and channel receives two bys (11⁄2˝) lumber. Moisture drainage vents are also installed.

Armour’s very own Mitered Aluminum Door Stop is included in all door hardware kits.

A Zinc Plated, Neoprene, Wall Mount, Adjustable Stay Roller is provided with each sliding door to prevent the door from being pushed into the aisle-way.

All of Armour’s Lumber Panels are treated with Thompson’s Water Seal® before assembly and sealer can be omitted upon request. Painting or staining over lumber sealer is recommended. Armour Stall Doors have nonprotruding fasteners. Counter Sunk Screws are placed only in the back of Armour lumber panels, for an attractive and unmarred fascia. 

Installation instructions are provided.

www.armourgates.com


ALUMINUM SLIDING STALL DOORS Sliding Stall Door Details: 4´3½˝ width x 8´0˝ height is our Standard Size. Custom Sizes and 7´0˝ Height Available

CBSD4 Crossbuck Sliding Door with Standard Bar Top

CBSD4LOP Crossbuck Sliding Door with Lift-out Panel CBGGSD4 Crossbuck Gossip Top Sliding Door

SDSO Sliding Door Superstructure with Standard Bar Top

COMPLETELY ASSEMBLED CHOICES OF STYLES AND LUMBER FACIAS STANDARD AND CUSTOM HEIGHTS AVAILABLE SUPERIOR STRENGTH

COOLSD4 Coolbreeze Sliding Door with Standard Bar Top 

COOLSD4SPRFDD Coolbreeze Sliding Door with Spring-loaded Fold-down Panel

COOLGGSD4 Coolbreeze Gossip Top Sliding Door

COOLSD4LOP Coolbreeze Sliding Door with Lift-out Panel


TGSD4 Horizontal T&G Sliding Door* with Standard Bar Top

TGSD4SPRFDD Horizontal T&G Sliding Door* with Spring-loaded Fold-down Panel

VTGSD4 Vertical T&G Sliding Door with Standard Bar Top

TGGGSD4 T&G Gossip Top Sliding Door*

INSTALLATION INSTRUCTIONS HEAVY-DUTY INSTALLATION HARDWARE INCLUDED OPTIONAL FOLD-DOWN OR LIFT-OUT PANELS DURABLE DESIGN

COOLWSP5 Coolbreeze Sliding Door with Scuff-panel with Standard Bar Top

CLSD4WSP5WOLSPRFDD Coolbreeze Sliding Door without lumber in Scuffpanel and Spring-loaded Fold-down Top Panel

*Available in Horizontal or Vertical T&G

COOLWSP5LOP Coolbreeze Sliding Door with Scuff-panel* and Lift-out Panel

TGBONESD4 T&G Sliding Door* with Herringbone Top 

www.armourgates.com


COOLBREEZE SLIDING STALL DOORS Ventilation and Visibility COMPLETELY ASSEMBLED ALL ALUMINUM – NO RUST CHOICE OF BAR OR SCUFF-PANEL BOTTOM STRAIGHT, GOSSIP OR HERRINGBONE TOP AVAILABLE HEAVY-DUTY INSTALLATION HARDWARE INCLUDED INSTALLATION INSTRUCTIONS OPTIONAL FOLD-DOWN OR LIFT-OUT PANELS

COOLBREEZE Sliding Stall Doors can be ordered to promote ventilation in new buildings or replace old doors which tend to stifle air. Coolbreeze doors not only assist in ventilating air-bound stalls, but they allow visibility into stalls when foals inhabit the area.

Sliding Stall Door Details 4´3½˝ width x 8´0˝ height

Coolbreeze are made with two heavy duty lengths of vertical square tubing on each side of the door frame to insure structural integrity is maintained. Upper vertical bar pickets are one inch round schedule 40 aluminum tubing spaced at three inches between pickets on top 4´0˝. The same vertical picket tubing size is used in the lower two or four foot portion of the door in combination with a closer bar ratio of one inch between bars. All pickets in the Coolbreeze door feature our concealed weld technique for a clean and finished appearance. Hardware includes – one galvanized 8´0˝ overhead selfcleaning & aligning door track, two neoprene silent-glide ball-bearing trolleys, rated 450 pound capacity each, two all aluminum door stops, one half-inch diameter latch, one adjustable wall mount stay roller with neoprene roller and all necessary fasteners for hardware installation. Doors are prepared with predrilled latch and trolley areas to insure a trouble-free installation and well operating component.

Send us your plans and let us maximize your barn’s ventilation. 

One inch bar spacing and center channel reinforcement in lower portion of doors.


CWSPGGSD5 Coolbreeze Sliding Door with Gossip-top and Scuff-panel*

COOLSD4 & L SERIES GRILLE Coolbreeze Sliding Stall Door & Stall Front Grille (attaching to lumber)

COOLWSP5 Coolbreeze Sliding Door with Scuff-panel*

COOLGGSD4 & L SERIES GRILLE Coolbreeze Sliding Door with Gossp Top & Stall Front Grille (attaching to lumber)

COOLGGSD4 Coobreeze Sliding Door with Gossip-top 

www.armourgates.com


WINDOW GRILLES/STALL FRONTS/DIVIDER Increase ventilation in air-bound stalls COMPLETELY ASSEMBLED - NOTHING TO PUT TOGETHER! ALL ALUMINUM - NO RUST! STANDARD & CUSTOM SIZES AVAILABLE NO LOOSE PIECES CONCEALED WELDS CONSTRUCTION UNCLUTTERED & CLEAN APPEARANCE BUILT-IN FEEDER ACCESS DOORS & LIFT OUT PANELS OPTIONAL NO PAINTING EVER INCREASE VISIBILITY Armour Grilles can be used in a variety of places throughout your stable. Our Stall Front Grilles are designed to fit above the existing stall wall. Divider Grilles are mounted in between stalls for increased ventilation and socializing. Window Grilles qualify for any size smaller that 4´0˝ wide x 4´0˝ high and everything else are deemed grilles. Stall fronts traditionally have a Feeder Access Door at the corner of the stall front. This option is to provide easy access to feeding areas without entering the stall. Armour offers a Lift-out Panel which allows a portion of the grille to be removed for an extended period of time.

Grille Details Standard size grilles are 3’0˝ or 4’0˝ heights and available in lengths up to sixteen feet. Custom Sizes are available. We make renovations a snap! Just send in your measurements. Grilles are available with or without our innovative built-in Feeder Access Doors which make feeding time a breeze. L Series Grilles are assembled with angle horizontals and fit over any 1½˝ lumber. L Series grilles arrive predrilled with fasteners. C Series Grilles, or channel grille, are manufactured for installation into CBS, or concrete block structures and arrive with predrilled fastener holes.

⁄8˝ vs. 1⁄16˝ thickness.

1

Both series grilles are manufactured with 1⁄8˝ thickness vertical pickets of 1˝ inch diameter round tubing and 1⁄8˝ angle or channel horizontals and a three inch between bar spacing is standard. A closer ratio one or two inch spacing available when necessary, please see below.

1˝ Between Bar Spacing. 

2˝ Between Bar Spacing.

3˝ Between Bar Spacing.


L SERIES Stall Front or Window Grille for lumber installation

C SERIES Stall Front Grille with Feeder Access Door for concrete installation

FAD Feeder Access Door Open

Feeder Access Door Closed

LOP Lift-out Panel feature built into any size window, front or divider grille L SERIES Divider or partition grilles for lumber (pictured)

C SERIES Divider or partition grilles for concrete (not pictured) 

www.armourgates.com


ALUMINUM GOSSIP GATES Old World Styling Merged with Modern Craftsmanship

COMPLETELY ASSEMBLED ALL ALUMINUM SUPERSTRUCTURE UNIQUE ZEPHYR-STYLE BAR TOP CHOICE OF FASCIAS LUMBER TREATED WITH THOMPSON’S WATER SEAL® HEAVY-DUTY HARDWARE INCLUDED A great deal of labor goes into the preparation of Armour’s Gossip Gates to provide each of our customers the added advantage of a trouble-free installation: Components are manufactured using Armour’s standard techniques: concealed welds, capped posts, pre-drilled hinge & latch holes and moisture drainage vents. In addition, each gate is squared before securing protective aluminum channels around lumber areas. To insure a proper trouble-free installation, zinc-plated fasteners, 6˝ Tee-hinges and a slide bolt latch are ALL provided.

Gossip Gate Details 4´0˝ wide x 5´0˝ height

Gossip Gates are manufactured with two 5´0˝ height channel posts which are secured, at several points, to Armour’s unique triple-bar Zephyr Top. The upper horizontal channel stands at a 4´0˝ height while the Zephyr Top is approximately 12˝ higher bringing the overall door height to 5´0˝. Lumber panels can be ordered in the popular Crossbuck, Horizontal or Vertical Tongue & Groove. Lumber panels are layered, glued, fastened with countersunk screws in the rear of gate fascias and then a generous application of Thompson’s Water Seal® is applied. If ventilation is a concern, try Armour’s Coolbreeze gate with or without a Scuff-panel or a Taube Vent-a-Bar gate.

Hunt Facility Rockford, Illinois 

Clark Barn Palm City, Florida

Monterey Farm, Pierson, Florida


CBGG3 Crossbuck Gossip Gate

CWSPGG3 Coolbreeze Gossip Gate with Scuff-panel*

TGGG3 T&G Gossip Gate*

TVGG3 Taube Gossip Gate

COOLGG3 Coolbreeze Gossip Gate

SMOOTHGG3 Smoothie Gossip Gate

SG3 Stallion Guard • Easily mounts on any Armour Gossip Gate • All Connecting Hardware Included • Converts Gossip Top to a Full Bar Top • One Piece Aluminum Construction • Does Not Interfere with Gate Function Moves with Gate • Perfect for Long Periods of Restraint

VCG • All Aluminum • Adds Character to any “v˝ • Prevents Cribbing • Covers already Cribbed area • Onlly Filts Armour Products *Available in Horizontal or Vertical T&G



www.armourgates.com


DUTCH DOORS – SINGLE OR DOUBLE Traditional Styling Combined with Innovative Construction COMPLETELY ASSEMBLED LUMBER INCLUDED FRAME MITER-CUT ALUMINUM DOUBLE OR SINGLE SWING AVAILABLE CHOICE OF LUMBER FACIAS LUMBER TREATED WITH THOMPSON’S WATER SEAL® HEAVY-DUTY HARDWARE INCLUDED STANDARD AND CUSTOM SIZES AVAILABLE Armour Dutch Doors are offered as a single or double panel and are available in a variety of designs. The time honored Crossbuck, Vertical or Horizontal Tongue and Groove, Coolbreeze with or without a Scuff Panel and Smoothie are among the fascias to choose. Whether you are choosing a back or front door for the stalls, Dutch doors can be ordered to meet all of your equine needs. When ordering a door with lumber, please inquire about our “Reversed Facia˝ at no additional cost. Armour lumber Dutch doors arrive with the crossbuck or tongue and groove design on the outside of the door when the door is in the closed position. If you prefer the design to show when the door top or bottom is open, then tell us to reverse the fascia on the top, bottom or both panels. Lumber Dutch doors are manufactured with Armour’s techniques: Layered lumber panels, routing, sanding, gluing, 21 step fastening, Thompson’s Water Seal® application, and miter-cut channel installation. Door panels arrive fully assembled with lumber in position, predrilled hinge and latch holes and fasteners for lumber barn installation are included.

Lumber Dutch Door Details 4´0˝ width x 4´0˝ height OR 3´111⁄2˝ width x 3´111⁄2˝ height

Coolbreeze and Scuff Panel Dutch Details 4´0˝ width x 4´0˝ height

Armour’s Bar Top or Coolbreeze with or without a Scuff Panel may be ordered for restraint, as well as, ventilation. The Bar Top is assembled with 1˝ round bars and 3˝ between bar spacing. The round bars in the Bar Top also match all Armour stall front and divider grilles. Bar Tops arrive as a fully welded assembly and include hinges and latches as well as fasteners for a lumber installation. Coolbreeze Half Dutch Gates are assembled with the same 1˝ round tube bars and have a 1˝ between bar spacing. A center channel is installed for additional strength and rigidity. The Coolbreeze with Scuff Panel is manufactured by combining the materials and techniques of Armour’s lumber Dutch doors and Coolbreeze Half Dutch gates. Scuff Panels can be ordered in vertical or horizontal tongue and groove or crossbuck. 10


7CBDD2 Crossbuck Double Dutch 7´0˝ height Reverse Fascia pictured on door top only

ABCHD1 Abbie Coolbreeze Half Dutch*

CBHD1 Crossbuck Half Dutch

ABCWSPHD1 Abbie Coolbreeze Half Dutch with Scuff-panel*

CBDD2 Crossbuck Double Dutch (Door arrives unpainted)

TGHD1 T&G Half Dutch*

SMOOTHHD1 Smoothie Half Dutch

CBHD1 Crossbuck Half Dutch *Available in Horizontal or Vertical T&G

BTHD1 & TGHD1 Hinged Bar Top & T&G Half Dutch*

11

www.armourgates.com


SHUTTERS – SINGLE or DOUBLE Available in Hinged or Sliding COMPLETELY ASSEMBLED LUMBER WITH ALUMINUM MITER-CUT CHANNELS CHOICE OF LUMBER FASCIAS UNCLUTTERED & CLEAN APPEARANCE LUMBER TREATED WITH THOMPSON’S WATER SEAL® HEAVY DUTY HARDWARE INCLUDED STANDARD AND CUSTOM SIZES AVAILABLE Armour Shutters are offered as a single or double panel and can be ordered hinged or sliding. A variety of fascia designs are available to match Armour Sliding Doors and Dutch Doors. The time honored Crossbuck, Vertical or Horizontal Tongue and Groove and Smoothie are among the fascias you may choose. Whether you are choosing shutters for each stall or other areas of the barn, Armour will assist with custom sizing any window opening. When ordering a swinging shutter, please inquire about our Reversed Fascia at no additional cost. Armour Shutters arrive with the crossbuck or tongue and groove design on the OUTSIDE of the shutter when the SHUTTER is in the CLOSED position. If you prefer the design to show when the shutter is open, then tell us to “Reverse the fascia.˝ Armour shutters are manufactured by applying extensive assembly techniques such as layered lumber panels, routing, sanding, gluing, 21 step fastening, Thompson’s Water Seal® application, and miter-cut channel installation. Shutter panels arrive fully assembled with lumber in position, predrilled hinge and latch holes and moisture drainage vents installed.

Standard Shutter Details

12

Hinged Single Panel Smooth Smooth Smooth Crossbuck Crossbuck Crossbuck T&G T&G T&G

Product # #SSHSMOOTH3X3 #311SSHSMOOTH4X4 #SSHSMOOTH4X4 #SSHCB3X3 #311SSHCB4X4 #SSHCB4X4 #SSHTG3X3 #311SSTGHD4X4 #SSTGHD4X4

Shutter Size 3´0˝ w x 3´0˝ h 3´111⁄2˝ w x 3´111⁄2˝ h 4´0˝ w x 4´0˝ h 3´0˝ w x 3´0˝ h 3´111⁄2˝ w x 3´111⁄2˝ h 4´0˝ w x 4´0˝ h 3´0˝ w x 3´0˝ h 3´111⁄2˝ w x 3´111⁄2˝ h 4´0˝ w x 4´0˝ h

Opening Size 3´1⁄2˝ w x 3´1⁄2˝ h 4´0˝ w x 4´0˝ h 4´1⁄2˝ w x 4´1⁄2˝ h 3´1⁄2˝ w x 3´1⁄2˝ h 4´0˝ w x 4´0˝ h 4´1⁄2˝ w x 4´1⁄2˝ h 3´1⁄2˝ w x 3´1⁄2˝ h 4´0˝ w x 4´0˝ h 4´1⁄2˝ w x 4´1⁄2˝ h

Hinged Double Panel Smooth Crossbuck T&G

Product # #DSHSMOOTH4X4 #DSHCB4X4 #DSHTG4X4

Shutter Size (Two Each) 2´0˝ w x 4´0˝ h 2´0˝ w x 4´0˝ h 2´0˝ w x 4´0˝ h

Opening Size 4´1˝ w x 4´1⁄2˝ h 4´1˝ w x 4´1⁄2˝ h 4´1˝ w x 4´1⁄2˝ h

Sliding Single Panel Smooth Smooth Crossbuck Crossbuck T&G T&G

Product # #SSLSMOOTH3X3 #SSLSMOOTH4X4 #SSLCBS3X3 #SSLCBS4X4 #SSLTGS3X3 #SSLTGS4X4

Shutter Size 3´31⁄2˝ w x 3´0˝ h 4´31⁄2˝ w x 4´0˝ h 3´31⁄2˝ w x 3´0˝ h 4´31⁄2˝ w x 4´0˝ h 3´31⁄2˝ w x 3´0˝ h 4´31⁄2˝ w x 4´0˝ h

Opening Size 3´0˝ w x 2´11˝ h 4´0˝ w x 3´11˝ h 3´0˝ w x 2´11˝ h 4´0˝ w x 3´11˝ h 3´0˝ w x 2´11˝ h 4´0˝ w x 3´11˝ h

Sliding Double Panel Smooth Crossbuck T&G

Product # #DSLSMOOTH4X4 #DSLCBS4X4 #DSLTGS4X4

Shutter Size (Two Each) 2´31⁄2˝ w x 4´0˝ h 2´31⁄2˝ w x 4´0˝ h 2´31⁄2˝ w x 4´0˝ h

Opening Size 4´0˝ w x 3´11˝ h 4´0˝ w x 3´11˝ h 4´0˝ w x 3´11˝ h


Single Swing Hinged Crossbuck Shutter Installed

Double Swing Hinged T&G Shutters Installed

SSHCB4X4 Single Swing Hinged Crossbuck 4’x4’ Shutter Grille with Lift-out Panel Sold Separately**

DSHTG4X4 Double Swing Hinged T&G 4’x 4’ Shutter Set* Grille Sold Separately**

DSHSMOOTH4X4 Double Swing Hinged Smoothie 4´x4´ Shutter Set

Single Sliding T&G Shutter Installed*

SSLTGS4X4 Single Sliding T&G 4´x4´ Shutter* Grille Sold Separately**

*Available in Horizontal or Vertical T&G **See Window Grilles page 6&7

SSHSMOOTH4X4 Single Swing Hinged Smoothie 4´x4´ Shutter

13

www.armourgates.com


END BARN DOOR SUPERSTRUCTURES Unique Frame to Avoid Heavy Lifting COMPLETELY ASSEMBLED FRAME HEAVY DUTY - ALL ALUMINUM – NO RUST CUSTOM SIZES AVAILABLE REINFORCED VERTICAL SIDES RECEIVES 2X6 LUMBER HEAVY-DUTY HARDWARE INCLUDED Armour sets the industry standard with its innovative End Barn Door Superstructure. The Superstructure is available in many popular standard sizes

Seven Eighths Farm Killingworth, Connecticut

or can be handcrafted to individual barn owner requirements. Manufacturing procedures enable owners and builders to install door frames without cranes or multi-man crews. Once positioned, leveled, and plumb, the Superstructure can be filled with locally cut and purchased 2x6 lumber.

End Barn Door Details When ordering Armour’s No Rust Superstructure, please specify the overall end barn opening. Armour custom sizes the door frames to accommodate your barn’s end opening measurements. Armour also offers an array of standard sizes, if one is in the planning stages of a new facility. The Superstructure is manufactured entirely from the highest quality mill

Wind Song Equestrian Center Apopka, Florida

finished aluminum extrusions and utilizes our unique concealed welding technique. The superstructure has reinforced vertical tubes for extra strength and durability with a unique channel system to receive any 11⁄2 lumber. A Finish-plate Cover caps the last top board loaded into frame, giving the end door a completed appearance. Superstructures are shipped complete with all the necessary hardware including the best rounded track, heavy-duty ball-bearing trolleys, aluminum stops, bracings, and finish-plate covers. (See hardware detail on page 1.) At Armour Gates, providing a long lasting quality product to barn owners and builders is of our highest concern. In the future if a board in the Superstructure needs to be replaced, simply remove the unwanted and insert a new like sized board in the door top. Minimal maintenance allows more free time with horses.

Product Number SUPER4W8HED SUPER8W8HED SUPER10W8HED SUPER12W8HED SUPER8W10HED SUPER10W10HED SUPER12W10HED SUPER8W12HED SUPER10W12HED SUPER12W12HED 14

Opening Size 4´0˝ width x 8´0˝ height 8´0˝ width x 8´0˝ height 10´0˝ width x 8´0˝ height 12´0˝ width x 8´0˝ height 8´0˝ width x 10´0˝ height 10´0˝ width x 10´0˝ height 12´0˝ width x 10´0˝ height 8´0˝ width x 12´0˝ height 10´0˝ width x 12´0˝ height 12´0˝ width x 12´0˝ height

Door Size 4´31⁄2˝ width x 8´0˝ height Two 4´31⁄2˝ width x 8´0˝ height Two 5´2˝ width x 8´0˝ height Two 6´2˝ width x 8´0˝ height Two 4´2˝ width x 10´0˝ height Two 5´2˝ width x 10´0˝ height Two 6´2˝ width x 10´0˝ height Two 4´2˝ width x 12´0˝ height Two 5´2˝ width x 12´0˝ height Two 6´2˝ width x 12´0˝ height


CBDDNS5 Two Sliding Not Split Crossbuck Double Dutch Door 4´31⁄2˝width x 8´0˝ height

CBDDNS2 Hinged Not Split Crossbuck Double Dutch Door 4´0˝ width x 8´0˝ height

SUPER4W8HED Sliding Tack & Feed Room Door 4´31⁄2˝ width x 8’0˝ height Add your own lumber. SUPERED End Barn Door Superstructure Installation Hardware Incluced Lumber NOT Provided.

15

www.armourgates.com


MINIATURE STall Doors, GATES & GRILLES Now you have many, “mini˝ choices available. COMPLETELY ASSEMBLED LUMBER WITH ALUMINUM ALL ALUMINUM MITER-CUT FRAME UNIQUE ZEPHYR-STYLE GOSSIP TOP CHOICE OF STRAIGHT OR GOSSIP TOP LUMBER TREATED WITH THOMPSON’S WATER SEAL® ZINC-PLATED LATCHING & MOUNTING HARDWARE INCLUDED Armour’s miniature stall gates are available in three standard sizes and have the option of a straight top or unique Zephyr Gossip Top. Miniature gates are made with the same quality techniques that are used to manufacture Armour’s Stall Doors, Half Dutch Doors or Gossip Gates: concealed welds, capped posts, predrilled hinge and latch holes, moisture drainage vents, quality 1⁄8˝ aluminum used throughout, Thompson’s Water Sealed lumber and miter-cut channels to name a few. The aluminum pickets (bars) in the lower portion of gates are 1˝ round tubes and have a “mini-friendly˝ 1˝ between bar spacing. Miniature Stall Doors (1), Stall Fronts (2), Grilles (3)

1

and Dividing Partitions (4) are available.

Miniature Gate Details 36˝ width x 40˝ height 48˝ width x 48˝ height 36˝ width x 48˝ height 48˝ width x 60˝ height

straight top straight top gossip top gossip top

see page 17 see page 11 see page 17 see page 9

MINISMOOTHSD4 Miniature Smoothie Sliding Door 3 2

16

4


MINISMOOTHGG3 Mini Smoothie Gossip Gate

MINICBGG3 Mini Crossbuck Gossip Gate

MINITGGG3 Mini T&G Gossip Gate*

MINITVGG3 Mini Taube Gossip Gate

MINICOOLGG3 Mini Coolbreeze Gossip Gate

MINICOOLWSPGG3 Mini Coolbreeze Gossip Gate with Scuff-panel*

MINISMOOTH36x40 Mini Smoothie Gate

MINICB36x40 Mini Crossbuck Gate

MINITG36x40 Mini T&G Gate*

MINITV36x40 Mini Taube Vent Gate

MINICOOL36x40 Mini Coolbreeze Gate

MINICOOLWSP36x40 Mini Coolbreeze Gate with Scuff-panel* 17

*Available in Horizontal or Vertical T&G

www.armourgates.com


Air-flow Vent Panels Increases air-flow to your stalls instantly! COMPLETELY ASSEMBLED INCREASE VISIBILITY AND VENTILATION INTO STALL ALL ALUMINUM GRILLE READY TO INSTALL IN EXISTING STALL WALLS or DOORS NO LOOSE PIECES; NO RATTLING MITER-CUT FRAME ON FOUR SIDES STANDARD and CUSTOM SIZES AVAILABLE These units come in a variety of lengths and are manufactured in heights compatible with 2˝ x 6˝ or 2˝ x 8˝ lumber planking. Installation into stall front, divider walls or stall doors is quick and easy and only requires removal of a small lumber area. Vent Panels yield immediate results: ventilation. Panels arrive with miter-cut corners for a “picture framed˝ appearance and welded vertical pickets of 1˝ diameter round tubes, so the bars don’t rattle! The 1˝ spacing between bars is also safe for miniatures or foals. Air-flow Vent Panels also arrive with predrilled fasteners holes and the necessary mounting hardware for lumber installation.

Select a location for the vent panel…

Product Numbers VP45X5 VP45X7 VP45X22 VP33X33 VP40X22 VP24X7

18

Cut away lumber and insert panel…

Opening Size Required 451⁄2˝ width x 51⁄2˝ height 451⁄2˝ width x 71⁄2˝ height 451⁄2˝ width x 221⁄2˝ height 333⁄4˝ width x 333⁄4˝ height 401⁄2˝ width x 221⁄2˝ height 241⁄2˝ width x 71⁄2˝ height

And instantly free up air-bound stalls.

Product Size 48˝ width x 8˝ height 48˝ width x 10˝ height 48˝ width x 25˝ height 36˝ width x 36˝ height 43˝ width x 25˝ height 27˝ width x 10˝ height


STALL ACCESSORIES Personalize your barn!

FDBB7 Flip-down Blanket Bars 251⁄2˝ length x 4˝ deep STBB7 Stationary Blanket Bars 251⁄2˝ length x 4˝ deep Custom stationary blanket bar lengths available, any size less than 4˝.

BMPR7 Door Bumper Stop Includes fasteners for lumber installation

PGF7 Poly-grain Feeder 18˝ length x 9˝ width x 61⁄2˝ height

1CG-8CG Trim available in lengths 1´-8´ Cut to length,sold by the foot.Includes fasteners for lumber installation

FLXHK7 Rubber Flex-hook Hanger Hold up to 5 pounds Includes fasteners for lumber installation

SWAIL7 Single Decorative Swail One Piece 17˝ length x 13⁄4˝ width x 14˝ height

AWSTF7 Aluminum Wall Stiffener 11⁄2˝ x ¼˝ x any length up to 8´ Includes fasteners for lumber installation

TBCKS7 Tie Backs or Snap Holders Includes fasteners for lumber installation

SWAIL77 Double Decorative Swail Two Pieces 17˝ length x 13⁄4˝ width x 14˝ height

SWAIL777 Triple Decorative Swail Three Pieces 17˝ length x 13⁄4˝ width x 14˝ height

19

www.armourgates.com


CONSTRUCTION Brackets Assorted Sizes Available A wide assortment of innovative ALUMINUM BRACKETS make it easy to perform a variety of functions such as building stalls, securing overhead lumber headers, connecting horizontal planking to posts , and securing posts to concrete or wooden surfaces. You are sure to find many other uses for these non-rusting , sturdy units throughout your barn or stable.

908DB 51⁄2˝ x 51⁄2˝ x 73⁄4˝ x 1⁄8˝ 90 Degree Bracket

20

3118CA 3˝x 11⁄2˝ x 1-1/2˝ x 1/8˝ Clip Angles

658CP 6˝ x 51⁄2˝ x 1/8˝ Connector Plate

1178CA 13⁄4˝ x 13⁄4˝ x 71⁄2˝ x 1/8˝ Clip Angles

138CP 13⁄4˝ x 31⁄4˝ x 1/8˝ Connector Plate

3368CA 3˝ x 3˝ x 6˝ x 1⁄8˝ Clip Angles

3228CA 3˝ x 2˝ x 21⁄2˝ x 1/8˝ Clip Angles

1118CA 11⁄2˝ x 11⁄2˝ x 11⁄2˝ x 1⁄8˝ Clip Angles

1158CA 13⁄4˝ x 13⁄4˝ x 51⁄2˝ x 1⁄8˝ Clip Angles

11138CA 11⁄2˝ x 11⁄2˝ x 131⁄2˝ x 1⁄8˝ Clip Angles


Corner Shelf Kits

Armour Corner Shelf Kits provide additional storage space in your barn or stable in an area previously unused due to the nature of the corner itself. These sturdy kits come complete with two aluminum angle mounting brackets which are predrilled, installation fasteners for securing the shelf in both areas and the sturdy 3â „4Ë? thick corner cut lumber insert. Each shelf will support one hundred pounds easily when installed with fasteners furnished.

1

2

3 Select location, mark holes 4 Mark both angle brackets level with adjacent bracket Fasten both brackets (level) against corner walls level with adjacent bracket Position pre-cut lumber shelf 5 6 7

Hold shelf in desired location Fasten screws through brackets into shelf Paint if desired & shelf is ready to provide additional storage.

21

www.armourgates.com


Spitfire Ranch 1

Spitfire Ranch 2

Blum Barn

God’s Gift 1

Wolf Stables

Wind Song Farm & Equestrian Center

Reunion Stable

Double E

Field of Dreams

Link Barn

Tindel Stable

Cahoon Barn

Walker Barn

Hunt Facility

God’s Gift 2

Kitchen Creek Ranch

A L U M I N U M

H O R S E

S T A L L S

800-876-7706

info@armourgates.com • www.armourgates.com

We ship nationwide and internationally!


Armour Gates Horse Stall Catalog