Page 1

Service Manual S/N 523811001 & Above S/N 523911001 & Above S/N 524011001 & Above S/N 524111001 & Above

EQUIPPED WITH BOBCAT INTERLOCK CONTROL SYSTEM (BICS™) 6902498 (3-06)

Printed in U.S.A.

©Bobcat Company 2006


MAINTENANCE SAFETY WARNING

Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Operator’s Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow W-2003-0903 instructions can cause injury or death.

Safety Alert Symbol: This symbol with a warning statement, means: “Warning, be alert! Your safety is involved!” Carefully read the message that follows.

CORRECT

CORRECT

B-10731a

B-15590

Never service the Bobcat SkidSteer Loader without instructions.

Use the correct procedure to lift or lower operator cab.

CORRECT

B-15591

Cleaning and maintenance are required daily.

WRONG

WRONG

WRONG

B-15592

B-15593

B-15599

Have good ventilation when welding or grinding painted parts. Wear dust mask when grinding painted parts. Toxic dust and gas can be produced. Avoid exhaust fume leaks which can kill without warning. Exhaust system must be tightly sealed.

WRONG

B-15600

Stop, cool and clean engine of flammable materials before checking fluids. Never service or adjust loader with the engine running unless instructed to do so in the manual. Avoid contact with leaking hydraulic fluid or diesel fuel under pressure. It can penetrate the skin or eyes. Never fill fuel tank with engine running, while smoking or when near open flame.

Disconnecting or loosening any hydraulic tubeline, hose, fitting, component or a part failure can cause lift arms to drop. Do not go under lift arms when raised unless supported by an approved lift arm support device. Replace it if damaged.

Never work on loader with lift arms up unless lift arms are held by an approved lift arm support device. Replace if damaged. Never modify equipment or add attachments not approved by Bobcat Company.

WRONG

B-15601 B-16102 Keep body, jewelry and clothing

away from moving parts, electrical contact, hot parts and exhaust. Wear eye protection to guard from battery acid, compressed springs, fluids under pressure and flying debris when engines are running or tools are used. Use eye protection approved for type of welding. Keep rear door closed except for service. Close and latch door before operating the loader.

WRONG

B-6589 B-16102

Lead-acid batteries produce flammable and explosive gases. Keep arcs, sparks, flames and lighted tobacco away from batteries. Batteries contain acid which burns eyes or skin on contact. Wear protective clothing. If acid contacts body, flush well with water. For eye contact flush well and get immediate medical attention.

Maintenance procedures which are given in the Operation & Maintenance Manual can be performed by the owner/ operator without any specific technical training. Maintenance procedures which are not in the Operation & Maintenance Manual must be performed ONLY BY QUALIFIED BOBCAT SERVICE PERSONNEL. Always use genuine Bobcat replacement parts. The Service Safety Training Course is available from your Bobcat dealer. MSW08-0805


ALPHABETICAL INDEX ADVANCED CONTROL SYSTEM (ACS) ............... 60-01 AIR CLEANER .................................................... 70-01 AIR CLEANER SERVICE ....................................... 10-01 AIR CONDITIONING SERVICE.............................. 80-01 AIR CONDITIONING SYSTEM FLOW ................... 80-01 ALTERNATOR ........................................................ 60-01 BATTERY ................................................................ 60-01 BASIC TROUBLESHOOTING ................................ 80-01 BICSâ„¢ SYSTEM .................................................... 60-01 BOBCAT CONTROLLER .....................................60-01 BOB-TACH ............................................... 10-01, 50-01 BRAKE .................................................................... 40-01 BUCKET POSITION VALVE ................................ 20-01 CHAINCASE ........................................................... 40-01 CHARGE PRESSURE ............................................ 30-01 COMPONENTS ...................................................... 80-01 COMPRESSOR ...................................................... 80-01 CONDENSER ......................................................... 80-01 CONTROL HANDLE ............................................... 50-01 CONTROL HANDLE (ADVANCED CONTROL SYSTEM) (ACS) SELECTABLE HAND/FOOT CONTROL.... 50-01 CONTROL PANEL .................................................. 50-01 CONTROL PEDALS ............................................... 50-01 CONTROL PEDALS (ACS) .................................... 50-01 CONVERSIONS ............................................ SPEC-01 COOLING FAN ....................................................... 70-01 CYLINDER (LIFT) ................................................... 20-01 CYLINDER (POWER BOB-TACH).......................... 20-01 CYLINDER (TILT) ................................................ 20-01 DIAGNOSTICS .....................................................60-01 DRIVE BELT ........................................................... 30-01 DRIVE COMPONENTS .......................................... 40-01 ELECTRICAL SYSTEM INFORMATION ................ 60-01 ENGINE ................................................................. 70-01 ENGINE COMPONENTS AND TESTING .............. 70-01 ENGINE COOLING SYSTEM ................................. 10-01 ENGINE LUBRICATION SYSTEM.......................... 10-01 ENGINE SPECIFICATIONS ...........................SPEC-01 ENGINE SPEED CONTROL .................................. 70-01 EVAPORATOR........................................................ 80-01 EVAPORATOR/HEATER UNIT ............................... 80-01 EXPANSION VALVE ............................................... 80-01 FAN GEARBOX ...................................................... 10-01 FINAL DRIVE TRANSMISSION (CHAINCASE) ..10-01 FLYWHEEL AND HOUSING ................................70-01 FRONT AUXILIARY HYD. COUPLER BLOCK....... 20-01 FUEL SYSTEM ....................................................... 10-01 FUEL TANK............................................................. 50-01 GENERAL AIR CONDITIOING SERVICE GUIDELINES........................................80-01

HEATER COIL ......................................................... 80-01 HEATER/AC FAN .................................................... 80-01 HEATER VALVE ...................................................... 80-01 HIGH FLOW VALVE ................................................ 20-01 HYDRAULIC CONNECTION SPECS. .............. SPEC-01 HYDRAULIC CONTROL VALVE (ADVANCED CONTROL SYSTEM) (ACS) ...........20-01 HYDRAULIC CONTROL VALVE (FOOT CONTROL)................................................ 20-01 HYDRAULIC FILTER HOUSING ............................. 20-01 HYDRAULIC FLUID RESERVOIR .......................... 20-01 HYDRAULIC FLUID SPECIFICATIONS ........ SPEC-01 HYDRAULIC/HYDROSTATIC SYSTEM..................10-01 HYDRAULIC PUMP ................................................ 20-01 HYDRAULIC PUMP (HI FLOW) ..............................20-01 HYDRAULIC SYSTEM INFORMATION ..................20-01 HYDROSTATIC MOTOR ..................................... 30-01 HYDROSTATIC PUMP ........................................ 30-01 HYDROSTATIC SYSTEM INFORMATION ..........30-01 INSTRUMENT PANEL............................................. 60-01 LIFT ARMS.............................................................. 50-01 LIFT ARM BY-PASS CONTROL VALVE .............. 20-01 LIFT ARM SUPPORT DEVICE ........................... 10-01 LIFTING AND BLOCKING THE LOADER............... 10-01 LIGHTS ................................................................60-01 LOADER SPECIFICATIONS ............................. SPEC-01 LUBRICATING THE BOBCAT LOADER ................. 10-01 MAIN RELIEF VALVE .............................................. 20-01 MUFFLER................................................................ 70-01

OIL COOLER........................................................... 30-01 OPERATOR CAB .........................................10-01, 50-01 OPERATOR SEAT...................................................50-01 OPERATOR SEAT (SUSPENSION)........................ 50-01 POWER BOB-TACH ................................. 10-01, 50-01 POWER BOB-TACH BLOCK................................... 20-01 PRESSURE RELIEF VALVE ................................... 80-01 PRESSURE SWITCH.............................................. 80-01


ALPHABETICAL INDEX (CONT’D)

RPM SENSOR........................................................ 70-01 RADIATOR.............................................................. 70-01 REAR AUXILIARY DIVERTER VALVE ....................20-01 REAR DOOR .......................................................50-01 REAR GRILL ...........................................................50-01 RECEIVER/DRIER ..................................................80-01 RECONDITIONING THE ENGINE ..........................70-01 REGULAR MAINTENANCW ...................................80-01 REMOTE START ................................................ 10-01 RPM SENSOR.........................................................70-01 SAFETY ...................................................................80-01 SEAT BAR ...............................................................50-01 SEAT BAR SENSOR ...............................................60-01 SERVICE SCHEDULE ............................................10-01 SPARK ARRESTOR MUFFLER ............................. 10-01 STARTER ................................................................60-01 SYSTEM CHARGING AND RECLAMATION ......... 80-01 SYSTEM TROUBLESHOOTING CHART .............. 80-01 TEMPERATURE/PRESSURE .................................80-01 THERMOSTAT.........................................................80-01 TIRE MAINTENANCE .............................................10-01 TORQUE SPECIFICATIONS FOR BOLTS .... SPEC-01 TOWING THE LOADER ..........................................10-01 TRACTION LOCK....................................................60-01 TRANSPORTING THE BOBCAT LOADER.............10-01 TROUBLESHOOTING.............................................70-01 TURBOCHARGER ..................................................70-01


SAFETY & MAINTENANCE

CONTENTS FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . II SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V

HYDRAULIC SYSTEM

SERIAL NUMBER LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . IX DELIVERY REPORT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X

HYDROSTATIC SYSTEM

BOBCAT LOADER IDENTIFICATION. . . . . . . . . . . . . . . . . . . . . . . . XI SAFETY AND MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . 10-01 HYDRAULIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-01

DRIVE SYSTEM

HYDROSTATIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-01 MAIN FRAME DRIVE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-01 MAIN FRAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-01 ELECTRICAL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60-01

ELECTRICAL SYSTEM

ENGINE SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70-01 HEATING, VENTILATION, AIR CONDITIONING . . . . . . . . . . . . 80-01

ENGINE SERVICE

SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPEC-01 HVAC

SPECIFICATIONS

SPECIFICATION

I

S150, S160 Bobcat Loader Service Manual


FOREWORD This manual is for the Bobcat loader mechanic. It provides necessary servicing and adjustment procedures for the Bobcat loader and its component parts and systems. Refer to the Operation & Maintenance Manual for operating instructions, Starting procedure, daily checks, etc. A general inspection of the following items must be made after the loader has had service or repair: 1. Check that the ROPS/FOPS (Including side screens) is in good condition and is not modified.

9. The parking brake function correctly.

2. Check that ROPS mounting hardware is tightened and is Bobcat approved.

10. Enclosure door latches must open and close freely.

3. The seat belt must be correctly installed, functional and in good condition.

11. Bob-Tach wedges and linkages must function correctly and be in good condition.

4. The seat bar must be correctly adjusted, clean and lubricated.

12. Safety treads must be in good condition.

5. Check lift arm support device, replace if damaged.

13. Check for correct function of indicator lamps (Optional on some models).

6. Machine signs must be legible and in the correct location.

14. Check hydraulic fluid level, engine oil level and fuel supply.

7. Steering levers and foot pedals must return to neutral.

15. Inspect for fuel, hydraulic fluid leaks.

8. Check for correct function of the work lights

16. Lubricate the loader.

II

must

oil

or

S150, S160 Bobcat Loader Service Manual


17. Check the condition of the battery and cables.

22. Operate the loader and check all functions.

18. Inspect the air cleaner for damage or leaks. Check the condition of the element.

23. Check for any field modification not completed.

19. Check the electrical charging system.

24. Check for correct function of the Bobcat Interlock Control System (BICS™) before the machine is returned to the customer.

20. Check tires for wear and pressure.

25. Recommend to the owner that all necessary corrections be made before the machine is returned to service.

21. Inspect for loose or broken parts or connections.

CALIFORNIA PROPOSITION 65 WARNING Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects and other reproductive harm.

III

S150, S160 Bobcat Loader Service Manual


SAFETY INSTRUCTIONS

The following publications provide information on the safe use and maintenance of the Bobcat machine and attachments:

Safety Alert Symbol This symbol with a warning statement means: “Warning, be alert! Your safety is involved!” Carefully read the message that follows.

The Delivery Report is used to assure that complete instructions have been given to the new owner and that the machine is in safe operating condition.

The Operation & Maintenance Manual delivered with the machine or attachment contains operating information as well as routine maintenance and service procedures. It is a part of the machine and can be stored in a container provided on the machine. Replacement Operation & Maintenance Manuals can be ordered from your Bobcat dealer.

Machine signs (decals) instruct on the safe operation and care of your Bobcat machine or attachment. The signs and their locations are shown in the Operation & Maintenance Manual. Replacement signs are available from your Bobcat dealer.

An Operator’s Handbook fastened to the operator cab. It’s brief instructions are convenient to the operator. The handbook is available from your dealer in an English edition or one of many other languages. See your Bobcat dealer for more information on translated versions.

The AEM Safety Manual delivered with the machine gives general safety information.

The Service Manual and Parts Manual are available from your dealer for use by mechanics to do shoptype service and repair work.

The Skid-Steer Loader Operator Training Course is available through your local dealer or at www.training.bobcat.com or www.bobcat.com. This course is intended to provide rules and practices of correct operation of the Skid-Steer Loader. The course is available in English and Spanish versions.

Service Safety Training Courses are available from your Bobcat dealer or at www.training.bobcat.com or www.bobcat.com. They provide information for safe and correct service procedures.

The Skid-Steer Loader Safety Video is available from your Bobcat dealer or at www.training.bobcat.com or www.bobcat.com.

WARNING Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Operator’s Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death. W-2003-0903

WARNING Warnings on the machine and in the manuals are for your safety. Failure to obey warnings can cause injury or death. W-2044-1285

IMPORTANT This notice identifies procedures which must be followed to avoid damage to the machine. I-2019-0284

SI SSL-0206 SM

V

S150, S160 Bobcat Loader Service Manual


SAFETY INSTRUCTIONS (CONT’D) The dealer and owner/operator review the recommended uses of the product when delivered. If the owner/operator will be using the machine for a different application(s) he or she must ask the dealer for recommendations on the new use.

Call Before You Dig 1-888-258-0808 When you call, you will be directed to a location in your state/city for information about buried lines (telephone, cable TV, water, sewer, gas, etc.)

SI SSL-0206 SM

VI

S150, S160 Bobcat Loader Service Manual


SAFETY INSTRUCTIONS (CONT’D)

Use the procedure in the Operation & Maintenance Manual for connecting the battery and for jump starting.

Use the procedure in the Operation & Maintenance Manual for cleaning the spark arrestor muffler (if equipped).

Fire Prevention The machine and attachments have components that are at high temperature under normal operating conditions. The primary source of high temperatures is the engine and exhaust system. The electrical system, if damaged or incorrectly maintained, can be a source of arcs or sparks.

Figure 1

Flammable debris (leaves, straw, etc.) must be removed regularly. If flammable debris is allowed to accumulate, it will increase fire hazard. Clean often to avoid this accumulation. Flammable debris in the engine compartment is a potential hazard. The spark arrestor muffler is designed to control the emission of hot particles from the engine and exhaust system, but the muffler and the exhaust gases are still hot. •

Do not use the machine where exhaust, arcs, sparks or hot components can contact flammable material, explosive dust or gases.

The operator cab, engine compartment, and engine cooling system must be inspected every day and cleaned if necessary to prevent fire hazard and overheating.

Check all electrical wiring and connections for damage. Keep the battery terminals clean and tight. Repair or replace any damaged part.

Check fuel and hydraulic tubes, hoses and fittings for damage and leakage. Never use open flame or bare skin to check for leaks. Tighten or replace any parts that show leakage. Always clean fluid spills. Do not use gasoline or diesel fuel for cleaning parts. Use commercial nonflammable solvents.

Do not use ether or starting fluids on any engine which has glow plugs. These starting aids can cause explosion and injure you or bystanders.

Always clean the machine, disconnect the battery, and disconnect the wiring from the controllers before welding. Cover rubber hoses, battery and all other flammable parts. Keep a fire extinguisher near the machine when welding. Have good ventilation when grinding or welding painted parts. Wear a dust mask when grinding painted parts. Toxic dust or gas can be produced.

Stop the engine and let it cool before adding fuel. NO SMOKING!

Know where fire extinguishers and first aid kits are located and how to use them. Fire extinguishers are available from your Bobcat dealer [Figure 1].

SI SSL-0206 SM

VII

S150, S160 Bobcat Loader Service Manual


SERIAL NUMBER LOCATIONS

Engine Serial Number

Always use the serial number of the loader when requesting service information or when ordering parts. Early or later models (identification made by serial number) may use different parts, or it may be necessary to use a different procedure in doing a specific service operation.

Figure 2

Figure 1

1

P-21821

The engine serial number is located on the side of the engine [Figure 2].

P-45263

Loader Serial Number The loader serial number plate is located on the outside of the loader frame [Figure 1]. Explanation of loader Serial Number: XXXX

XXXXX Module 2. - Production Sequence (Series) Module 1. - Model / Engine Combination

1. The four digit Model/Engine Combination Module number identifies the model number and engine combination. 2. The five digit Production Sequence Number identifies the order which the loader is produced.

IX

S150, S160 Bobcat Loader Service Manual


DELIVERY REPORT Figure 3

B-16315

The delivery report must be filled out by the dealer and signed by the owner or operator when the Bobcat loader is delivered. An explanation of the form must be given to the owner. Make sure it is filled out completely [Figure 3].

X

S150, S160 Bobcat Loader Service Manual


BOBCAT LOADER IDENTIFICATION

FRONT LIGHTS

OPERATOR SEAT with SEAT BELT & SEAT BAR

GRAB HANDLES

TILT CYLINDERS FRONT AUXILIARY QUICK COUPLERS

BUCKET STEPS

STEPS B-19880

■ BUCKET

● OPERATOR CAB

(ROPS / FOPS) LIFT ARM SUPPORT DEVICE

◆ REAR AUXILIARY

QUICK COUPLERS

LIFT ARM REAR GRILL

LIFT CYLINDER

REAR DOOR REAR LIGHT TAIL LIGHT

❏ TIRES

B-19881

◆ Optional or Field Accessory (Not Standard Equipment) ❏ TIRES - Tires shown may not be standard. The machine is factory equipped with standard tires. Other tires are available. ■ Bucket - Several different buckets and other attachments are available for this machine. ● ROPS, FOPS - Roll Over Protective Structure, per SAE J1040 and ISO 3471, and Falling Object Protective Structure per SAE J1043 and ISO 3449, Level I. Level II is available.

XI

S150, S160 Bobcat Loader Service Manual


SAFETY & MAINTENANCE

SAFETY AND MAINTENANCE AIR CLEANER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-80-1 Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-80-1 Replacing Filter Element(s) . . . . . . . . . . . . . . . . . . . . . . . . 10-80-1

SAFETY & MAINTENANCE

BOB-TACH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-150-1 Inspection And Maintenance . . . . . . . . . . . . . . . . . . . . . . 10-150-1 ENGINE COOLING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . Checking The Coolant Level . . . . . . . . . . . . . . . . . . . . . . . Cleaning The Cooling System . . . . . . . . . . . . . . . . . . . . . . Replacing the Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . ENGINE LUBRICATION SYSTEM . . . . . . . . . . . . . . . . . . . . Checking Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oil Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Replacing Oil And Filter . . . . . . . . . . . . . . . . . . . . . . . . . .

10-90-1 10-90-2 10-90-1 10-90-2

10-110-1 10-110-1 10-110-1 10-110-1

FAN GEARBOX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-140-1 Checking And Maintaining . . . . . . . . . . . . . . . . . . . . . . . . 10-140-1 FINAL DRIVE TRANSMISSION (CHAINCASE) . . . . . . . . . . 10-130-1 Checking And Adding Oil . . . . . . . . . . . . . . . . . . . . . . . . . 10-130-1 Removing Oil From The Chaincase. . . . . . . . . . . . . . . . . 10-130-1 FUEL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Filling The Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing Air From The Fuel System . . . . . . . . . . . . . . .

10-100-1 10-100-1 10-100-2 10-100-1 10-100-2

HYDRAULIC/HYDROSTATIC SYSTEM . . . . . . . . . . . . . . . . Breather Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking And Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . Replacing Hydraulic Fluid . . . . . . . . . . . . . . . . . . . . . . . . Replacing Hydraulic/Hydrostatic Filter . . . . . . . . . . . . . . .

10-120-1 10-120-3 10-120-1 10-120-1 10-120-1

DRIVE SYSTEM

ELECTRICAL SYSTEM & ANALYSIS ENGINE SERVICE

SPECIFICATION

LIFT ARM SUPPORT DEVICE . . . . . . . . . . . . . . . . . . . . . . . . 10-20-1 Installing Lift Arm Support Device . . . . . . . . . . . . . . . . . . . 10-20-1 Removing Lift Arm Support Device . . . . . . . . . . . . . . . . . . 10-20-2 LIFTING AND BLOCKING THE LOADER . . . . . . . . . . . . . . . 10-10-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10-1 LUBRICATION OF THE BOBCAT LOADER . . . . . . . . . . . . . 10-160-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-160-1 Continued On Next Page

10-01

S150, S160 Bobcat Loader Service Manual


SAFETY AND MAINTENANCE (CONT’D) OPERATOR CAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emergency Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lowering The Operator Cab . . . . . . . . . . . . . . . . . . . . . . . Raising The Operator Cab . . . . . . . . . . . . . . . . . . . . . . . . .

10-30-1 10-30-1 10-30-3 10-30-2 10-30-1

POWER BOB-TACH (OPTION) . . . . . . . . . . . . . . . . . . . . . . 10-151-1 Inspection And Maintenance . . . . . . . . . . . . . . . . . . . . . . 10-151-1 REMOTE START. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-60-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-60-1 SERVICE SCHEDULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-70-1 Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-70-1 SPARK ARRESTOR MUFFLER . . . . . . . . . . . . . . . . . . . . . . 10-180-1 Cleaning Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-180-1 TIRE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rotating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wheel Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10-170-1 10-170-1 10-170-1 10-170-1

TOWING THE LOADER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-50-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-50-1 TRANSPORTING THE BOBCAT LOADER . . . . . . . . . . . . . . 10-40-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-40-1

10-02

S150, S160 Bobcat Loader Service Manual


LIFTING AND BLOCKING THE LOADER

Figure 10-10-2

Figure 10-10-1

P-45481 B-7023A

Put a floor jack under the rear of the loader. Lift the rear of the loader and install jackstands [Figure 10-10-2].

WARNING

Figure 10-10-3

Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death. W-2003-0199

Procedure Always park the loader on a level surface.

P-45482

Put the floor jack under the front of the loader.

WARNING Put jackstands under the front axles and rear corners of the frame before running the engine for service. Failure to use jackstands can allow the machine to fall or move and cause injury or death. W-2017-0286

Lift the front of the loader and put jackstands under the axle tubes [Figure 10-10-3]. NOTE: Make sure the jackstands do not touch the tires. Make sure tires clear the floor and any obstacles.

10-10-1

S150, S160 Bobcat Loader Service Manual


LIFT ARM SUPPORT DEVICE

Figure 10-20-1

Installing Lift Arm Support Device

WARNING

P-45481

2

Never work on a machine with the lift arms up unless the lift arms are secured by an approved lift arm support device. Failure to use an approved lift arm support device can allow the lift arms or attachment to fall and cause injury or death.

1

W-2059-0598 P-45251

WARNING

Put jackstands under the rear corners of the loader frame (Inset) [Figure 10-20-1].

Service lift arm support device if damaged or if parts are missing. Using a damaged lift arm support or with missing parts can cause lift arms to drop causing injury or death.

Disconnect the spring from the lift arm support device retaining pin (Item 1). Support the lift arm support device (Item 2) [Figure 10-20-1] with your hand and remove the retaining pin.

W-2271-1197

Figure 10-20-2

1

P-45252

Lower the lift arm support device on top of the lift cylinder. Hook the free end of the spring (Item 1) [Figure 10-20-2] to the lift arm support device so there will be no interference with the support device engagement. The operator must be in the operator's seat, with the seat belt fastened and seat bar lowered. Start the engine, and raise the lift arms all the way up.

10-20-1

S150, S160 Bobcat Loader Service Manual


LIFT ARM SUPPORT DEVICE (CONT’D)

Removing Lift Arm Support Device

Installing Lift Arm Support Device (Cont’d)

Figure 10-20-4

Figure 10-20-3

1 1

P-45485

P-45486

P-45484

Remove the pin from the lift arm support device.

Raise the lift arms until the lift arm support device drops onto the lift cylinder rod [Figure 10-20-3]. Lower the lift arms slowly until the lift arm support device is held between the lift arms and lift cylinder [Figure 1020-3]. Stop the engine. Raise the seat bar, and move both the pedals until both pedals lock. Install pin (Item 1) (Inset) [Figure 10-20-3].

Connect the spring (Item 1) [Figure 10-20-4] from the lift arm support device to the bracket below the lift arms. The operator must be in the operator's seat, with the seat belt fastened and seat bar lowered, until the lift arm support device is removed and the lift arms are lowered all the way. Start the engine, raise the lift arms all the way up. The spring will lift the support device off the lift cylinder rod. Lower the lift arms all the way and stop the engine.

NOTE: The lift arm support device must be tight against the cylinder rod. The tabs of the lift arm support device must be under the cylinder as shown (Inset) [Figure 10-20-3].

Raise the seat bar and move the pedals until both pedals lock. Disconnect the spring from the bracket. Figure 10-20-5

1 2

P-45251

Return the lift arm support device to storage position and insert pin (Item 1) through lift arm support device (Item 2) [Figure 10-20-5] and welded tab on boom. Connect spring to pin. Remove the jackstands. 10-20-2

S150, S160 Bobcat Loader Service Manual


OPERATOR CAB

Raising The Operator Cab

Description

Always stop the engine before raising or lowering the cab.

Figure 10-30-1 Stop the loader on a level surface. Lower the lift arms. If the lift arms must be up while raising the operator cab, install the lift arm support device. (See Installing Lift Arm Support Device on Page 10-20-1.) Install jackstands under the rear of the loader frame [Figure 10-30-1]. Figure 10-30-2

P-45481

The Bobcat loader has an operator cab (ROPS and FOPS) as standard equipment to protect the operator from rollover and falling objects. Check with your dealer if the operator cab has been damaged. The seat belt must be worn for roll over protection. ROPS/FOPS - Roll Over Protective Structure per SAE J1040 and ISO 3471, and Falling Object Protective Structure per SAE J1043 and ISO 3449, Level I. Level II is available.

P10564

P10563

Remove the nuts and plates [Figure 10-30-2] (both sides).

Level I - Protection from falling bricks, small concrete blocks, and hand tools encountered in operations such as highway maintenance, landscaping, and other construction site services. Level II - Protection from falling trees, rocks; for machines involved in site clearing, overhead demolition or forestry.

10-30-1

S150, S160 Bobcat Loader Service Manual


OPERATOR CAB (CONT'D)

Lowering The Operator Cab

Raising The Operator Cab (Cont’d)

Figure 10-30-4

Figure 10-30-3

N-20120

P-45262

P-45261

Always stop the engine before raising or lowering the cab.

WARNING

NOTE: Always use the grab handles to lower the cab.

Never modify operator cab by welding, grinding, drilling holes or adding attachments unless instructed to do so by Bobcat. Changes to the cab can cause loss of operator protection from rollover and falling objects, and result in injury or death.

Pull down on the bottom of the operator cab until it stops at the latching mechanism [Figure 10-30-4]. Release the latching mechanism (Inset) [Figure 10-30-4] and pull the cab all the way down.

W-2069-1299

Figure 10-30-5 Lift on the grab handle and bottom of the operator cab slowly until the cab is all the way up and the latching mechanism engages [Figure 10-30-3].

P10563

P10564

P10563

Install the plates and nuts [Figure 10-30-5] (both sides). Tighten the nuts to 40-50 ft.-lbs. (54-68 Nm) torque.

10-30-2

S150, S160 Bobcat Loader Service Manual


Figure 10-30-8

OPERATOR CAB (CONT’D) Emergency Exit Figure 10-30-6

N-20171

Front Door (If Equipped) P0660

The front opening on the operator cab and rear window provide exits.

NOTE: When an Operator Cab Enclosure Kit is installed, the window of the front door can be used as an emergency exit. [Figure 10-30-8]. NOTE: If the loader has a Special Application Door Kit installed, the window of the front door is NOT an emergency exit.

Rear Window (If Equipped) Pull on the tag on the top of the rear window to remove the rubber cord [Figure 10-30-6].

Pull the plastic loop at the top of the window in the front door to remove the rubber cord [Figure 10-30-8].

Figure 10-30-7 Figure 10-30-9

x P-45260 P-24472

Push the rear window out of the rear of the operator cab. Exit through the rear of the operator cab [Figure 10-307].

Push the window out with your foot [Figure 10-30-9] at any corner of the window. Exit through the front door.

10-30-3

S150, S160 Bobcat Loader Service Manual


Figure 10-40-2

TRANSPORTING THE BOBCAT LOADER Procedure

WARNING

P-24785

N-19048

Adequately designed ramps of sufficient strength are needed to support the weight of the machine when loading onto a transport vehicle. Wood ramps can break and cause personal injury. W-2058-0494

Figure 10-40-1

ALTERNATE FRONT TIE DOWN

N-18520 P-45989

1

P-45215

A loader with an empty bucket or no attachment must be loaded backward onto the transport vehicle [Figure 1040-1].

P-45218

Use the following procedure to fasten the Bobcat loader to the transport vehicle to prevent the loader from moving during sudden stops or when going up or down slopes [Figure 10-40-2]. •

Lower the bucket or attachment to the floor.

Stop the engine.

Engage the parking brake.

Install chains at the front and rear loader tie down positions (Inset) [Figure 10-40-2].

Fasten each end of the chain to the transport vehicle.

10-40-1

S150, S160 Bobcat Loader Service Manual

Be sure the transport and towing vehicles are of adequate size and capacity (See Capacities on Page SPEC-10-4.). The rear of the trailer must be blocked or supported (Item 1) [Figure 10-40-1] when loading or unloading the loader to prevent the front end of the trailer from raising up.


Figure 10-50-2

TOWING THE LOADER Procedure Figure 10-50-1

1

1 N-18409

• P-21769

Press the TRACTION LOCK OVERRIDE Button (Item 1) [Figure 10-50-2].

To prevent damage to the loaders hydrostatic system, the loader must be towed only a short distance at slow speed. (Example: Moving the loader onto a transport vehicle). The towing chain (or cable) must be rated at 1 & 1/2 times the weight of the loader. (See Capacities on Page SPEC-10-4.) Start the engine. If the electrical system is not functioning or the engine does not run, part of the brake system must be disassembled to move the loader. (See Guide Removal on Page 60-110-5.) •

Turn the key switch to RUN (Item 1) [Figure 10-50-1] (Standard Panel) OR press the RUN/ENTER Button (Deluxe Panel).

10-50-1

S150, S160 Bobcat Loader Service Manual


Figure 10-60-2

REMOTE START Procedure Figure 10-60-1

1

1

P-24651

Figure 10-60-3 P16115

The tool listed below will be needed to do the following procedure: MEL1563: Remote Start Tool Kit

1

The remote start (Item 1) [Figure 10-60-1] is required when the operator cab is in the raised position for service and the service technician needs to turn the key switch on, or start the engine. Example: control handle linkage neutral adjustment. P-24653

Lift and block the loader. (See LIFTING AND BLOCKING THE LOADER on Page 10-10-1.) Raise the lift arms (if required by the procedure) and install an approved lift arm support device. (See Installing Lift Arm Support Device on Page 10-20-1.) Raise the operator cab (if required by the procedure). (See Raising The Operator Cab on Page 10-30-1.) Open the rear door of the loader. Remove the plug (Item 1) [Figure 10-60-2] or disconnect the attachment control harness (Item 1) [Figure 10-60-3] if connected.

10-60-1

S150, S160 Bobcat Loader Service Manual


Figure 10-60-5

REMOTE START (CONT'D) Procedure (Cont'd)

WARNING

1

AVOID INJURY OR DEATH With the 7-pin connector plugged into the loader and Remote Start Key Switch in the OFF position, the loader can still be started from the operator panel inside the cab. Placing the key switch of the remote start tool in the run position disconnects the operator panel key switch from the start circuit. If the service technician will be working the engine area it is important to remove the operator panel keys. W-2357-0899

2

P-16116

The remote start tool (Item 1) has three rocker switches (Item 2) [Figure 10-60-5].

Figure 10-60-4

1

P-24652

Connect the remote start tool to the engine harness connector (Item 1) [Figure 10-60-4]. NOTE: The key switch on the right-hand side operator panel must be in the OFF position or the Remote Start Kit will not operate.

10-60-2

S150, S160 Bobcat Loader Service Manual


REMOTE START (CONT'D) Procedure (Cont'd) Figure 10-60-6

3

2

1

P16118

The traction lock switch (Item 1) [Figure 10-60-6] is used to turn traction lock on or off. Push the switch to the override position. The switch will illuminate to indicate traction lock OVERRIDE. In this position, the wheels are able to turn.

The maximum flow/variable flow switch (Item 2) [Figure 10-60-6] is used to activate the auxiliary hydraulics. Pressing the switch once will activate variable flow. Pressing the switch again, will activate maximum flow. The switch will illuminate to indicate which flow rate is active. Pressing the switch a third time, will turn the flow OFF. The switch is used when checking pressures and flow rate. The auxiliary pressure release (Item 3) [Figure 10-60-6] is used to release hydraulic pressure to the right hand and/or rear auxiliary couplers ONLY. NOTE: With the engine running; pushing and holding the pressure release switch will cause the engine to stop in three seconds. To relieve the pressure; continue to press the switch after the engine has COMPLETELY stopped.

10-60-3

S150, S160 Bobcat Loader Service Manual


SERVICE SCHEDULE Chart Maintenance work must be done at regular intervals. Failure to do so will result in excessive wear and early failures. The service schedule is a guide for correct maintenance of the Bobcat loader. Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death.

WARNING

W-2408-0801

SERVICE SCHEDULE ITEM

HOURS

SERVICE REQUIRED

Engine Oil

Check the oil level and add oil as needed.

Engine Air Filter and Air System

Check display panel. Service only when required. Check for leaks and damaged components.

Engine Cooling System

Clean debris from oil cooler, radiator and grill. Check coolant level in recovery tank. Add coolant as needed.

Tires

Check for damaged tires and correct air pressure.

Seat Belt, Seat Bar and Control Interlocks

Check the condition of seat belt. Check the seat bar and control interlocks. Clean dirt and debris from moving parts.

Safety Signs and Safety Tread

Check for damaged signs (decals) and safety treads. Replace any signs or safety treads that are damaged or worn.

Indicators & Lights (Opt.)

Check for correct operation of all indicators & lights.

Operator Cab

Check the fastening bolts, washers & nuts. Check the condition of cab.

Lift Arms, Cylinders, Bob-Tach Pivot Pins and Wedges

Lubricate with multi-purpose lithium based grease.

Fuel Filter

Remove the trapped water.

Bobcat Interlock Control System (BICS)

Check that four BICS indicator lights and functions are activated. See details in this Operation & Maintenance Manual.

Heater and A/C Filters

Clean or replace filters as needed during heating/cooling season.

Hydraulic Fluid, Hoses and Tubelines

Check fluid level and add as needed. Check for damage and leaks. Repair or replace as needed.

Final Drive Transmission (Chain case), Foot Pedals or Hand Controls, and Steering Levers

Check oil level. Check for correct operation. Repair or adjust as needed.

Wheel Nuts

❏ Check for loose wheel nuts and tighten to 160 ft.-lbs. (217 Nm) torque.

Parking Brake

Check operation.

Spark Arrestor Muffler

Clean the spark chamber.

Battery

Check cables, connections and electrolyte level. Add distilled water as needed.

Steering Shaft

Grease two fittings.

Engine/Hydros. Drive Belt

* Check for wear or damage. Adjust as needed.

Fan Drive Gearbox

Check gear lube level. Add as needed.

Alternator Belt

Check belt tension and adjust as needed.

Engine Oil and Filter

▼Replace oil and filter. Use CD or better grade oil and Bobcat filter.

Fuel Filter

Replace the filter element.

Bobcat Interlock Control System (BICS)

Check the function of the lift arm bypass control.

Hydraulic Reservoir Breather Cap

Replace the reservoir breather cap.

Hydraulic/Hydrostatic Filter

●Replace the filter element.

Hydraulic Reservoir

Replace the fluid.

Final Drive Trans.(Chaincase)

Replace the fluid

Case Drain Filters

■Replace the filters.

8-10

50

100

■ 250

■ 500

■ 1000

■ Or every 12 months. ❏ Check wheel nut torque every 8 hours for the first 24 hours.

First oil and filter change must occur at 50 hours; 250 hours thereafter.

*

Inspect the new belt after first 50 hours.

Replace filter element after the first 50 hours and when the transmission warning light comes ON.

10-70-1

S150, S160 Bobcat Loader Service Manual


AIR CLEANER SERVICE

Replacing Filter Element(s)

Checking

OUTER FILTER

Figure 10-80-1

Figure 10-80-3

1 1

P-21769A

P-31836

It is important to change the air filter element only when the Air Cleaner icon in the right panel is ON (Item 1) [Figure 10-80-1] and you hear three beeps from the alarm.

Remove the wing nut (Item 1) [Figure 10-80-3] and remove the dust cover. Figure 10-80-4

Replace the inner filter every third time the outer filter is replaced or as indicated on (See SERVICE SCHEDULE on Page 10-70-1.) Figure 10-80-2

1

2

P-43239

1 Remove the wing nut (Item 1) [Figure 10-80-4] from the outer filter element. Remove the outer filter element.

N-18409

Press and hold the LIGHT Button (Item 1) [Figure 10-802] for two seconds. If the filter element needs replacement, the CODE [0117] (Air Filter Plugged) will show in the HOURMETER / CODE DISPLAY (Item 2) [Figure 10-80-2].

10-80-1

S150, S160 Bobcat Loader Service Manual


Figure 10-80-6

AIR CLEANER SERVICE (CONT’D) Replacing Filter Element(s) (Cont’d) Figure 10-80-5

1

P-43241

Remove the inner filter wing nut (Item 1) [Figure 10-806].

P-31837

Figure 10-80-7 NOTE: Be sure all sealing surfaces are clean. Install the new filter element and washer. Tighten the wing nut [Figure 10-80-5]. NOTE: Be sure sealing washer is in place on each wing nut [Figure 10-80-4]. Install the dust cover and tighten the wing nut. Check the air intake hose and the air cleaner housing for damage. Make sure all connections are tight.

1

INNER FILTER P-31838

Only replace the inner filter element under the following conditions:

Remove the inner filter (Item 1) [Figure 10-80-7]. •

Replace the inner filter element every third time the outer filter is replaced.

Install a new filter and tighten the wing nut.

After the outer element has been replaced, start the engine and run at full RPM. If the HOURMETER / CODE DISPLAY shows [01-17] (Air Filter Plugged), replace the inner filter element.

10-80-2

S150, S160 Bobcat Loader Service Manual


ENGINE COOLING SYSTEM

Figure 10-90-2

WARNING Wear safety glasses to prevent eye injury when any of the following conditions exist: • When fluids are under pressure. • Flying debris or loose material is present. • Engine is running. • Tools are being used. W-2019-1285

Check the cooling system every day to prevent overheating, loss of performance or engine damage. Cleaning The Cooling System

P-45501

Raise the oil cooler. Clean the top of the radiator [Figure 10-90-2].

Figure 10-90-1 NOTE: Use low air pressure or low water pressure to clean the radiator or damage to the radiator fins may result. Lower the oil cooler and air conditioning condenser (if equipped). Check cooling system for leaks. Install the rear grill and close the rear door.

P-45101

Open the rear door and remove the rear grill. Raise the air conditioning condenser (if equipped) (See CONDENSER on Page 80-120-1.) Use air pressure or water pressure to clean the top of the oil cooler [Figure 10-90-1].

WARNING Do not use your bare hands to remove debris from the oil cooler. Cooling fins are sharp and may cause injury. W-2460-0303

10-90-1

S150, S160 Bobcat Loader Service Manual


Replacing the Coolant

ENGINE COOLING SYSTEM (CONT’D) Checking The Coolant Level

WARNING

Figure 10-90-3

Do not remove radiator cap when the engine is hot. You can be seriously burned. W-2070-1285

Figure 10-90-4

P-45106

1 P-45102

Open the rear door and remove the rear grill. Look at the side of the coolant recovery tank [Figure 1090-3]. Check the coolant level. The level markers are on the side of the tank. Coolant must be at the bottom marker when the engine is cold; top marker when hot. Install the rear grill and close the rear door before operating the loader.

P-45102

Open the rear door and remove the rear grill. Remove the radiator cap (Item 1) [Figure 10-90-4].

IMPORTANT AVOID ENGINE DAMAGE Always use the correct ratio of water to antifreeze. Too much antifreeze reduces cooling system efficiency and may cause serious premature engine damage. Too little antifreeze reduces the additives which protect the internal engine components; reduces the boiling point and freeze protection of the system. Always add a premixed solution. Adding full strength concentrated coolant can cause serious premature engine damage. I-2124-0497

10-90-2

S150, S160 Bobcat Loader Service Manual


Add premixed coolant, 47% water and 53% propylene glycol to the recovery tank if the coolant level is low.

ENGINE COOLING SYSTEM (CONT’D) Replacing the Coolant (Cont’d)

Mix the coolant in a separate container. (See Capacities on Page SPEC-10-4, for correct capacity.)

KUBOTA V2203-EB

One gallon and one pint (4,3 L) of propylene glycol mixed with one gallon (3,8 L) of water is the correct mixture of coolant to provide a -34°F (-37°C) freeze protection.

Figure 10-90-5

Use a refractometer to check the condition of propylene glycol in your cooling system. 1

Fill the radiator with the premixed coolant. Install the radiator cap. Remove the cover from the coolant recovery tank. Fill the tank until it is at the lower marker.(side of tank). Run the engine until it is at operating temperature. Stop the engine. Check the coolant level in the recovery tank when cool. N-20586

Add coolant as needed. Connect a hose to the engine block drain valve (Item 1) [Figure 10-90-5]. Open the drain valve and drain the coolant into a container.

Install the rear grill and close the rear door.

KUBOTA V2003T-EB (TURBO) Figure 10-90-6

1

P-45490

Connect a hose to the engine block drain valve (Item 1) [Figure 10-90-6]. Open the drain valve and drain the coolant into a container. Recycle or dispose of used coolant in an environmentally safe manner. Close the drain valve and remove the hose. NOTE: The loader is factory filled with propylene glycol coolant (purple color). DO NOT mix propylene glycol with ethylene glycol.

10-90-3

S150, S160 Bobcat Loader Service Manual


FUEL SYSTEM

Figure 10-100-1

Fuel Specifications Use only clean, high quality diesel fuel, Grade No. 2 or Grade No. 1. The following is one suggested blending guideline which should prevent fuel gelling during cold temperatures: Temp. F°/ C° +15° (-9° ) Down to -20° / (-29° ) Below -20° / (-29° )

No. 2 100% 50% 0%

No.1 0% 50% 100%

1 P-45959

Contact your fuel supplier for local recommendations. Filling The Fuel Tank

Open the rear door. Remove the fuel fill cap (Item 1) [Figure 10-100-1]

WARNING

Figure 10-100-2

WRONG

Stop and cool the engine before adding fuel. NO SMOKING! Failure to obey warnings can cause an explosion or fire. W-2063-0887

WARNING Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil. Failure to use care around combustibles can cause explosion or fire which can result in injury or death.

B-19895

W-2103-1285

Use a clean, approved safety container to add fuel of the correct specifications. Add fuel only in an area that has free movement of air and no open flames or sparks. NO SMOKING! [Figure 10-100-2]. Install and tighten the fuel fill cap (Item 1) [Figure 10100-1].

10-100-1

S150, S160 Bobcat Loader Service Manual


FUEL SYSTEM (CONT’D)

WARNING

Fuel Filter Figure 10-100-3

Diesel fuel or hydraulic fluid under pressure can penetrate skin or eyes, causing serious injury or death. Fluid leaks under pressure may not be visible. Use a piece of cardboard or wood to find leaks. Do not use your bare hand. Wear safety goggles. If fluid enters skin or eyes, get immediate medical attention from a physician familiar with this injury. W-2072-0496

2

Figure 10-100-4

1 3 P-45960

(See SERVICE SCHEDULE on Page 10-70-1.), for the service interval for removing water from, or replacing the fuel filter. 2

Removing Water Loosen the drain (Item 1) [Figure 10-100-3] at the bottom of the filter element to remove water from the filter. Replacing Element

1

P-45959

Open the vent (Item 1) [Figure 10-100-4] on the fuel filter housing.

Remove the filter element (Item 2) [Figure 10-100-3]. Clean the area around the filter housing. Put clean oil on the seal of the new filter element. Install the fuel filter, and hand tighten.

Squeeze the hand pump (priming bulb) (Item 2) [Figure 10-100-4] until fuel flows from the vent with no air bubbles. Close the vent (Item 1) [Figure 10-100-4] on the fuel filter housing.

Remove the air from the fuel system. (See Below.) Removing Air From The Fuel System

Open the vent (Item 3) [Figure 10-100-4] on the fuel injection pump.

After replacing the filter element or when the fuel tank has run out of fuel, the air must be removed from the fuel system before starting the engine.

Squeeze the hand pump (priming bulb) (Item 2) [Figure 10-100-4] until the pump feels solid. Tighten the vent plug (Item 3) [Figure 10-100-4]. Start the engine. It may be necessary to open the vent plug (Item 3) [Figure 10-100-4] briefly while the engine is running. Close the vent when the engine runs smoothly.

10-100-2

S150, S160 Bobcat Loader Service Manual


ENGINE LUBRICATION SYSTEM

Replacing Oil And Filter

Checking Engine Oil

Figure 10-110-2

Check the engine oil level every day before starting the engine for the work shift.

2

Figure 10-110-1 1

N-20587

1

P-45959

2 (See SERVICE SCHEDULE on Page 10-70-1.), for the service interval for replacing the engine oil and filter. N-20588

P-45960

Run the engine until it is at operating temperature. Stop the engine. Open the rear door and remove the dipstick (Item 1) [Figure 10-110-1].

Open the rear door.

Keep the oil level between the marks on the dipstick.

Remove the rear grill.

Use a good quality motor oil that meets API Service Classification of CD or better (See Oil Chart below).

Remove the drain plug (Item 2) [Figure 10-110-2].

Install the dipstick and close the rear door.

Drain the oil into a container and dispose of used oil in an environmentally safe manner.

Oil Chart

Remove the oil filter (Item 1) [Figure 10-110-2]. Clean the filter housing surface.

RECOMMENDED SAE VISCOSITY NUMBER

C° (LUBRICATION OILS FOR DIESEL ENGINE CRANKCASE)

Put clean oil on the new oil filter gasket. Install the filter and hand tighten. Install and tighten the drain plug. Remove the fill cap (Item 2) [Figure 10-110-2].

F° *

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE(DIESEL ENGINES MUST USE API CLASSIFICATION CD, CF4, CG4) Can be used ONLY when available with appropriate diesel rating.

10-110-1

S150, S160 Bobcat Loader Service Manual


ENGINE LUBRICATION SYSTEM (CONT’D) Replacing Oil And Filter (Cont’d)

WARNING Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil. Failure to use care around combustibles can cause explosion or fire which can result in injury or death. W-2103-1285

Figure 10-110-3

1

P1575

Put oil in the engine. (See Capacities on Page SPEC-104.) [Figure 10-110-3] (See Oil Chart on Page 10-110-1.) Start the engine and let it run for several minutes. Stop the engine and check for leaks at the oil filter. Remove the dipstick and check the oil level. Add oil as needed if it is not between the marks (Item 1) [Figure 10-110-3] on the dipstick. Install the dipstick and the fill plug. Close the rear door.

10-110-2

S150, S160 Bobcat Loader Service Manual


HYDRAULIC/HYDROSTATIC SYSTEM

Replacing Hydraulic/Hydrostatic Filter

Checking And Adding Fluid

(See SERVICE SCHEDULE on Page 10-70-1.) for the correct service intervals.

Figure 10-120-1 Open the rear door. Remove the filter element (Item 2) [Figure 10-120-2]. Clean the surface of the filter housing where the seal contacts the housing. Put clean oil on the seal of the new filter element. Install and hand tighten the filter element. Close the rear door before operating the loader. Replacing Hydraulic Fluid N-18445

Use only recommended fluid in the hydraulic system. (See Specifications on Page SPEC-50-1.) Stop the loader on a level surface.

(See SERVICE SCHEDULE on Page 10-70-1.), for the service interval. The fluid must be replaced if it becomes contaminated or after major repairs. If the fluid is replaced, the hydrostatic filter and both case drain filters must be replaced.

Lower the lift arms and tilt the Bob-Tach fully back. Stop the engine.

Use only recommended fluid in the hydraulic system. (See Specifications on Page SPEC-50-1.)

Check fluid level in the sight gauge [Figure 10-120-1].

Stop the loader on a level surface.

Open the rear door and remove the rear grill.

Lower the lift arms and tilt the Bob-Tach fully back.

Figure 10-120-2

Stop the engine. Check fluid level in the sight gauge [Figure 10-120-1]. Open the rear door and remove the rear grill.

1

Figure 10-120-3 P-45243

P-45243

2 P-45244

1

Remove the fill cap (Item 1) [Figure 10-120-2]. Add the fluid as needed to bring the level to the center of the sight gauge [Figure 10-120-1]. Install the fill cap. Replace the rear grill and close the rear door.

P-45245

Remove the reservoir fill cap (Item 1) [Figure 10-120-3].

10-120-1

S150, S160 Bobcat Loader Service Manual


Figure 10-120-5

HYDRAULIC/HYDROSTATIC SYSTEM (CONT’D) Replacing Hydraulic Fluid (Cont’d)

WARNING 1 Hydraulic fluid escaping under pressure can have sufficient force to enter a person’s body by penetrating the skin. This can cause serious injury and possible death if proper medical treatment by a physician familiar with this injury is not received immediately.

2

W-2145-0290 P-45493

WARNING Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil. Failure to use care around combustibles can cause explosion or fire which can result in injury or death. W-2103-1285

Figure 10-120-4

Disconnect the hose (Item 1) [Figure 10-120-5] from the case drain filter located on the right drive motor. Use a plug and cap on the filter and case drain hose to prevent leakage. Remove the case drain filters (Item 2) [Figure 10-120-4] & [Figure 10-120-5] and drain the fluid into a container. Replace the hydraulic/hydrostatic filter element. (See Replacing Hydraulic/Hydrostatic Filter on Page 10-1201.) Replace both hydrostatic motor case drain filters (Item 2) [Figure 10-120-4] & [Figure 10-120-5]. Connect the hoses to the case drain filters.

2 Add the correct fluid to the reservoir until the fluid level is at the center of the sight gauge (Do not overfill). Lower the operator cab. (See Lowering The Operator Cab on Page 10-30-2.)

1

Start the engine and operate the loader hydraulic controls. P-45499

Stop the engine and check for leaks. Raise the operator cab. (See Raising The Operator Cab on Page 10-30-1.)

Check the fluid level in the reservoir and add as needed.

Drain the hydraulic fluid reservoir. (See Fluid Removal on Page 20-80-1.) Disconnect the hoses (Item 1) [Figure 10-120-4] from the case drain filter located on the reservoir. Use a plug and cap on the filter hose and case drain hose to prevent leakage.

10-120-2

S150, S160 Bobcat Loader Service Manual


HYDRAULIC/HYDROSTATIC SYSTEM (CONT’D) Breather Cap Figure 10-120-6

1

P-34227

(See SERVICE SCHEDULE on Page 10-70-1.), for the correct replacement interval. Raise the operator cab. (See Raising The Operator Cab on Page 10-30-1.) Remove the breather cap (Item 1) [Figure 10-120-6] and discard. Install new cap. Lower the operator cab. (See Lowering The Operator Cab on Page 10-30-2.)

10-120-3

S150, S160 Bobcat Loader Service Manual


FINAL DRIVE TRANSMISSION (CHAINCASE)

Removing Oil From The Chaincase

Checking And Adding Oil

Figure 10-130-2

Figure 10-130-1

1 1

P1616 P-45496

The chaincase contains the final drive sprockets and chains and uses the same type of oil as the hydraulic/ hydrostatic system. (See Specifications on Page SPEC50-1.)

Remove the cover (Item 1) [Figure 10-130-2] which is installed over the drain plug at the bottom rear of the chaincase. Figure 10-130-3

Stop the loader on a level surface. Stop the engine. Remove the plug (Item 1) [Figure 10-130-1] from the front of the chaincase housing. If oil can be reached with the tip of the your finger through the hole the oil level is correct.

1

If the level is low, add oil through the check plug hole until the oil flows from the hole. P1619

Install and tighten the plug.

Remove the drain plug (Item 1) [Figure 10-130-3] and drain the oil into a container. Check the drain plug and replace as necessary. Replace the drain plug and cover.

10-130-1

S150, S160 Bobcat Loader Service Manual


FAN GEARBOX Checking And Maintaining Figure 10-140-1

1

N-18460

(See SERVICE SCHEDULE on Page 10-70-1.) for the correct service interval. Raise the operator cab. (See Raising The Operator Cab on Page 10-30-1.) Remove the plug (Item 1) [Figure 10-140-1] to check the lubricant level. If the level is low, add SAE 90W gear lubricant through the check plug hole until lubricant flows from the hole. Install and tighten the plug. Lower the operator cab. (See Lowering The Operator Cab on Page 10-30-2.)

10-140-1

S150, S160 Bobcat Loader Service Manual


Figure 10-150-3

BOB-TACH Inspection And Maintenance

Bob-Tach Wedge

WARNING Bob-Tach wedges must extend through the holes in attachment. Levers must be fully down and locked. Failure to secure wedges can allow attachment to come off and cause injury or death. W-2102-0588

Wedge Must Contact Lower Edge Of Hole In The Attachment

Figure 10-150-1

B-15177

The spring loaded wedge (Item 1) [Figure 10-150-1] must contact the lower edge of the hole in the attachment (Item 1) [Figure 10-150-2] and [Figure 10-150-3].

1

If the wedge does not contact the lower edge of the hole [Figure 10-150-2] and [Figure 10-150-3], the attachment will be loose and can come off the Bob-Tach. Figure 10-150-4

N-17027

Move the Bob-Tach levers to engage the wedges [Figure 10-150-1]. The levers and wedges must move freely. Figure 10-150-2

TS-1062

Inspect the mounting frame on the attachment and the Bob-Tach, linkages and wedges for excessive wear or damage [Figure 10-150-4]. Replace any parts that are damaged, bent, or missing. Keep all fasteners tight.

1

Look for cracked welds. Contact your Bobcat dealer for repair or replacement parts. N-16044A

The wedges must extend through the holes in the attachment mounting frame (Item 1) [Figure 10-150-1].

Lubricate the wedges. (See SERVICE SCHEDULE on Page 10-70-1 and LUBRICATION OF THE BOBCAT LOADER on Page 10-160-1.)

10-150-1

S150, S160 Bobcat Loader Service Manual


Figure 10-151-3

POWER BOB-TACH (OPTION) Inspection And Maintenance Figure 10-151-1 FRONT ACCESSORY PANEL

1 B-15177

Wedge Must Contact Lower Edge Of Hole In The Attachment

N-17022A

If the wedge does not contact the lower edge of the hole [Figure 10-151-3], the attachment will be loose and can come off the Bob-Tach.

B-15891

Push and hold the BOB-TACH "WEDGES UP" switch until wedges are fully raised. Push and hold the BOBTACH "WEDGES DOWN" switch [Figure 10-151-1] until the wedges are fully down. The wedges must move freely.

Figure 10-151-4

Figure 10-151-2

TS-1062

Inspect the mounting frame on the attachment and the Bob-Tach, linkages and wedges for excessive wear or damage [Figure 10-151-4]. Replace any parts including decals and lever that are damaged, bent, or missing. Keep all fasteners tight. Inspect the hoses and fittings for leaks.

1 N-16043A

The wedges must extend through the holes in the attachment mounting frame (Item 1) [Figure 10-151-2] and must contact the lower edge of the hole in the attachment [Figure 10-151-2] and (Item 1) [Figure 10151-3].

Look for cracked welds. Contact your Bobcat dealer for repair or replacement parts. Lubricate the wedges. (See SERVICE SCHEDULE on Page 10-70-1 and LUBRICATION OF THE BOBCAT LOADER on Page 10-160-1.)

10-151-1

S150, S160 Bobcat Loader Service Manual


Figure 10-160-2

LUBRICATION OF THE BOBCAT LOADER Procedure Figure 10-160-1

1

2 P-45256 P-45255

Access Hole

Lubricate the loader as specified in the (SERVICE SCHEDULE Page 10-01), for the best performance of the loader. Record the operating hours each time you lubricate the Bobcat loader. Always use a good quality lithium based multi-purpose grease when you lubricate the loader. Apply lubricant until extra grease shows.

P-45973

2. Lift Cylinder Base [Figure 10-160-2].

End

(Both

Sides)

Figure 10-160-3

Lubricate the following locations on the loader: 3

1. Lift Cylinder Rod End (Both Sides) [Figure 10-160-1]

N-18510

3. Tilt Cylinder Base [Figure 10-160-3].

10-160-1

End

(Both

Sides)

S150, S160 Bobcat Loader Service Manual


Figure 10-160-6

LUBRICATION OF THE BOBCAT LOADER (CONT’D) Procedure (Cont’d) Figure 10-160-4

8

4

5 P-45253

8. Lift Arm Pivot Pin (Both Sides) [Figure 10-160-6]. P-45975

Figure 10-160-7 4. Tilt Cylinder Rod End. [Figure 10-160-4]. 5. Bob-Tach Pivot Pin (Both Sides) [Figure 10-160-4]. Figure 10-160-5

6 9 P-45976 P-45497

9. 250 Hours: Steering Lever Shaft [Figure 10-160-7].

7 P16045

6. Bob-Tach Wedge (Both Sides) [Figure 10-160-5]. 7. Power Bob-Tach Cylinder (If Equipped) (Both Sides) [Figure 10-160-5].

10-160-2

S150, S160 Bobcat Loader Service Manual


Recommended tire pressure must be maintained to avoid excessive tire wear and loss of stability and handling capability. Check for the correct pressure before operating the loader.

TIRE MAINTENANCE Wheel Nuts Figure 10-170-1

Mounting

WARNING Do not inflate tires above specified pressure. Failure to use correct tire mounting procedure can cause an explosion which can result in injury or death. W-2078-1285

IMPORTANT

P-45221

(See SERVICE SCHEDULE on Page 10-70-1.), for the service interval to check the wheel nuts. The correct torque is 160 ft.-lbs. (217 Nm) torque [Figure 10-170-1].

Inflate tires to the MAXIMUM pressure shown on the sidewall of the tire. DO NOT mix brands of tires used on the same loader. I-2057-0794

Rotating Check the tires regularly for wear, damage and pressure. Inflate tires to the maximum pressure shown on the sidewall of the tire. Figure 10-170-2

Tires are to be repaired only by an authorized person using the proper procedures and safety equipment. Tires and rims must always be checked for correct size before mounting. Check rim and tire bead for damage. The rim flange must be cleaned and free of rust. The tire bead and rim flange must be lubricated with a rubber lubricant before mounting the tire. Avoid excessive pressure which can rupture the tire and cause serious injury or death. During inflation of the tire, check the tire pressure frequently to avoid over inflation.

B-9976

Rear tires usually wear faster than front tires. To keep tire wear even, move the front tires to the rear and rear tires to the front [Figure 10-170-2]. It is important to keep the same size tires on each side of the loader. If different sizes are used, each tire will be turning at a different rate and cause excessive wear. The tread bars of all the tires must face the same direction.

10-170-1

S150, S160 Bobcat Loader Service Manual


SPARK ARRESTOR MUFFLER

WARNING

Cleaning Procedure

Never use machine in atmosphere with explosive dust or gases or where exhaust can contact flammable material. Failure to obey warnings can cause injury or death.

IMPORTANT This loader is factory equipped with a U.S.D.A. Forestry Service approved spark arrestor muffler. It is necessary to do maintenance on this spark arrestor muffler to keep it in working condition. The spark arrestor muffler must be serviced by dumping the spark chamber every 100 hours of operation.

W-2068-1285

Figure 10-180-1

If this machine is operated on flammable forest, brush or grass covered land, it must be equipped with a spark arrestor attached to the exhaust system and maintained in working order. Failure to do so will be in violation of California State Law, Section 4442 PRC. Make reference to local laws and regulations for spark arrestor requirements.

1

I-2022-0595

P-45498

WARNING When the engine is running during service, the steering levers must be in neutral and the parking brake engaged. Failure to do so can cause injury or death. W-2006-0284

(See SERVICE SCHEDULE on Page 10-70-1.) for service interval for cleaning the spark arrestor muffler. Do not operate the loader with a defective exhaust system. Stop the engine. Open the rear door and remove the rear grill. Remove the plug (Item 1) [Figure 10-180-1] from the bottom of the muffler.

WARNING When an engine is running in an enclosed area, fresh air must be added to avoid concentration of exhaust fumes. If the engine is stationary, vent the exhaust outside. Exhaust fumes contain odorless, invisible gases which can kill without warning. W-2050-1285

Start the engine and run for about ten seconds while a second person, wearing safety glasses, holds a piece of wood over the outlet of the muffler. This will force contaminants out through the cleanout hole. Stop the engine. Install and tighten the plug.

WARNING

Install the rear grill and close the rear door.

Stop engine and allow the muffler to cool before cleaning the spark chamber. Wear safety goggles. Failure to obey can cause serious injury. W-2011-1285

10-180-1

S150, S160 Bobcat Loader Service Manual


HYDRAULIC SYSTEM BUCKET POSITION VALVE . . . . . . . . . . . . . . . . . . . . . . . . . . Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . Removal and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . Solenoid Removal And Installation . . . . . . . . . . . . . . . . . . Solenoid Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20-90-1 20-90-4 20-90-2 20-90-1 20-90-1

CYLINDER (LIFT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . .

20-20-1 20-20-5 20-20-1 20-20-4 20-20-3 20-20-2

CYLINDER (POWER BOB-TACH) . . . . . . . . . . . . . . . . . . . . . Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . .

20-22-1 20-22-5 20-22-1 20-22-4 20-22-3 20-22-2

CYLINDER (TILT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Base End Pivot Pin Replacement . . . . . . . . . . . . . . . . . . . Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . Rod End Pivot Pin Bushing And Seal Replacement . . . . .

20-21-1 20-21-7 20-21-4 20-21-1 20-21-6 20-21-5 20-21-2 20-21-3

HYDRAULIC SAFETY SYSTEM &

DRIVE SYSTEM

ELECTRICAL SYSTEM & ANALYSIS ENGINE SERVICE

SPECIFICATION FRONT AUXILIARY HYDRAULIC COUPLER BLOCK. . . . . 20-130-1 Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . 20-130-1 Removal and Installation . . . . . . . . . . . . . . . . . . . . . . . . . 20-130-1 HIGH FLOW VALVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking The High Flow Relief Valve . . . . . . . . . . . . . . . Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . High Flow Relief Valve Adjustment Procedure . . . . . . . . Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . Solenoid Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20-100-1 20-100-1 20-100-6 20-100-3 20-100-4 20-100-8

Continued On Next Page

20-01

S150, S160 Bobcat Loader Service Manual


HYDRAULIC SYSTEM (CONT’D) HYDRAULIC CONTROL VALVE (ADVANCED CONTROL SYSTEM) (ACS). . 20-41-1 Actuator Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-12 Anti-Cavitation Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-18 Anti-Cavitation Valve/Port Relief Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-17 Auxiliary Electric Solenoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-22 Auxiliary Spool Removal And Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-21 BICS™ Valve, Check Valve Removal And Installation. . . . . . . . . . . . . . . . . 20-41-7 BICS™ Valve, Lift Arm By-Pass Orifice Removal And Installation . . . . . . . 20-41-7 BICS™ Valve Lock Valve Removal And Installation . . . . . . . . . . . . . . . . . . 20-41-9 BICS™ Valve Removal And Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-5 BICS™ Valve Solenoid Removal And Installation . . . . . . . . . . . . . . . . . . . 20-41-10 BICS™ Valve Solenoid Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-41-11 Cleaning And Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-23 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-1 Identification Chart (ACS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-13 Lift and Tilt Spool Disassembly And Assembly . . . . . . . . . . . . . . . . . . . . . 20-41-20 Lift Base End Restrictor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-14 Lift Spool Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-18 Load Check Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-14 Main Relief Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-15 Port-Auxiliary Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-23 Port Relief Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-16 Removal and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-1 Tilt Spool Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-41-19 HYDRAULIC CONTROL VALVE (FOOT CONTROL) . . . . . . . . . . . . . . . . . . . . 20-40-1 Anti-Cavitation Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-15 Anti-Cavitation Valve/Port Relief Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-15 Auxiliary Electric Solenoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-29 Auxiliary Spool Removal And Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-28 BICS™ Valve, Check Valve Removal And Installation. . . . . . . . . . . . . . . . . 20-40-7 BICS™ Valve, Lift Arm By-Pass Orifice Removal And Installation . . . . . . . 20-40-6 BICS™ Valve Lock Valve Removal And Installation . . . . . . . . . . . . . . . . . . 20-40-8 BICS™ Valve Removal And Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-4 BICS™ Valve Solenoid Removal And Installation . . . . . . . . . . . . . . . . . . . . 20-40-9 BICS™ Valve Solenoid Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-10 Cleaning And Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-31 Identification Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-40-11 Lift And Tilt Lock Block Removal And Installation . . . . . . . . . . . . . . . . . . . 20-40-17 Lift Spool and Detent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-17 Load Check Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-12 Main Relief Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-13 Port-Auxiliary Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-30 Port Relief Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-14 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-1 Rubber Boot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-16 Tilt Spool Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40-26 Continued On Next Page

20-02

S150, S160 Bobcat Loader Service Manual


HYDRAULIC SYSTEM (CONT’D) HYDRAULIC FILTER HOUSING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-70-1 Removal and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-70-1 HYDRAULIC FLUID RESERVOIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-80-1 Fluid Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-80-1 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-80-1 HYDRAULIC PUMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Check The Output Of The Hydraulic Pump With Power Bob-Tach.. . . Check The Output Of The Hydraulic Pump Without Power Bob-Tach. Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20-60-1 20-60-3 20-60-1 20-60-8 20-60-7 20-60-5

HYDRAULIC PUMP (HI FLOW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Check The Output Of The Hydraulic Pump With Power Bob-Tach.. . . Check The Output Of The Hydraulic Pump Without Power Bob-Tach. Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20-61-1 20-61-3 20-61-1 20-61-8 20-61-7 20-61-5

HYDRAULIC SYSTEM INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . 20-10-1 Tighten Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-10-5 Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-10-5 LIFT ARM BY-PASS CONTROL VALVE . . . . . . . . . . . . . . . . . . . . . . . . . . Disassembly and Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inspecting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removal and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20-50-1 20-50-2 20-50-1 20-50-1

MAIN RELIEF VALVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removal and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20-30-1 20-30-2 20-30-1 20-30-2

POWER BOB-TACH BLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-120-1 Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-120-3 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-120-1 REAR AUXILIARY DIVERTER VALVE . . . . . . . . . . . . . . . . . . . . . . . . . . .20-110-1 Disassembly And Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-110-4 Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-110-9 Removal And Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-110-1 Solenoid Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-110-9

20-03

S150, S160 Bobcat Loader Service Manual


Thank you very much for your reading. Please Click Here Then Get More Information.

BOBCAT S160 SKID STEER LOADER Service Repair Manual SN 524111001 & Above  
BOBCAT S160 SKID STEER LOADER Service Repair Manual SN 524111001 & Above  
Advertisement