Page 1

FORWARD The labor hours specified in this manual are set by DAEDONG`s qualified service mechanics. The service hour for every service task was precisely measured based on the experience of our mechanics. Then, the labor hour was set by applying adjustment factors to this service hour so that this manual could be used by mechanics having different levels of expertise and servicing in various regions. The features of this manual are as follows; 1. Figures and reference numbers used in this manual are identical to those in the part manual to make searching easier. 2. As every individual part and component has its own code (except for hardware), it is easy to locate correct job codes faster. 3. The index attached to this manual serves as an additional measure for convenient searching of job codes. How to use this manual 1. The same job code should not be used more than once since the labor hour for one job code is for both disassembly and re-assembly jobs. 2. In most cases, only one code should be used in one group (page) at a time. However, * More than one job code can be used in one group when performing several different tasks. * One job code can be used two times in case when both LH and RH parts are serviced at the same time. 3. Do not use subordinate job codes even if they are in different groups. For example, “Bonnet R & R” and “Complete engine R & R should not be used at the same time since “Bonnet R & R” is included in “Complete engine R & R”. In this case, only “Complete engine R & R” should be used. 4. Use of a separate warranty request form is required for each failure.

M50-US-00-A.indd 1

2009-07-06 오후 2:12:59


FORWARD 5. Use only one job code when servicing several adjacent or related parts. For example, if the bevel gear, its shaft and bearings are replaced the same time, use only the top level job code applicable. 6. Time taken for reconditioning, resealing, overhaul, related oil draining and refilling, part flushing and adjustment after replacing parts are included in the labor hours of these job codes. Therefore, there is no need to include other job codes for such services. 7. Labor hours for diagnosis and implement R & R are not included the job codes. Use the following extra job codes as needed with specific job descriptions on the warranty request form: * X999001: 0.5 hr. R & R of detachable main body of loaders, backhoes, mid-mount mowers, etc. * X999002: 1.0 hr. Diagnosis time * X999003: 2.0 hr. R & R of components used in the mounting of loaders, backhoes, mid-mount mowers, etc. 8. Failure to by the above instructions when drawing up the warranty request form (including on-line request) will result in rejection of your warranty claim. 9. If additional time is used for service, indicate details as to why and how many hours were needed in the description field of the form. Use of random job codes will result in your warranty being rejected.

M50-US-00-A.indd 2

2009-07-06 ě˜¤í›„ 2:12:59


table of contents GROUP NO INDEX 1 INDEX 2 INDEX 3 4A220LX-E010 4A220-E020 4A220LW-E030 3B183-E040 TD2200-E050 4A220A-E080 4B243LX-E090 4A220LX-E100 4A200LW-E110 4A200B-E120 4A220-E130 4A220LX-E140 3B183-E150 4B243-E160 3A150LX-E170 4A200LX-E180 4A220LXM-E190 4A220LWE-E200 4A200-E220 DS4510-T480A

M50-US-00-A.indd 3

GROUP NAME PAGE SECTIONAL GROUP...............................7 SORTED BY GROUP NAME.................11 SORTED BY PART NAME.....................15 CYLINDER BLOCK GROUP.................24 OIL PAN GROUP...................................26 CYLINDER HEAD GROUP....................28 GEAR CASE GROUP............................30 MAIN BEARING CASE GROUP............32 VALVE ROCKER ARM GROUP.............34 CYLINDER HEAD COVER GROUP......36 CAMSAFT GROUP................................38 PISTON & CRANK SHAFT GROUP......40 FLYWHEEL GROUP..............................42 NOZZLE HOLDER GROUP...................44 FUEL CAMSHAFT GROUP...................46 SPEED CONTROL PLATE GROUP......48 ENGINE STOP LEVER GROUP............50 GOVERNER GROUP............................52 WATER PUMP GROUP.........................54 WATER HOSE GROUP.........................56 DYNAMO GROUP.................................58 MANIFOLD GROUP..............................60 FRONT AXLE SUPPORT GROUP........62

GROUP NO D380L-T500A DS4510-T520A EX45H-T525A DS4510-T530A CT445B-T540A DS4510-T540A D360-T110A DS4510-T130A DS4510-T140A DS4510-T150A DS4510-T160A DS4510-T170A DS4510-T180A DK40-T195A D360-T200A DK40-T215A DS4510-T220A DS4510-T240A D360-T260A D360-T270A D43-T270A DS4510-T275A D360-T290A

GROUP NAME PAGE BEVEL PINION SHAFT GROUP...........64 BEVEL GEAR SHAFT GROUP.............66 FRONT DIFFERENTIAL GROUP..........68 FRONT AXLE CASE GROUP................70 BEVEL GEAR CASE GROUP...............72 FRONT AXLE GROUP..........................74 CLUTCH LEVER GROUP.....................76 CLUTCH HOUSING GROUP................78 MID CASE GROUP...............................80 TRANSMISSION CASE GROUP...........82 MAIN SHAFT GROUP...........................84 COUNTER SHAFT GROUP..................86 SHUTTLE SHAFT GROUP....................88 PTO COUNT SHAFT GROUP...............90 RANGE SHAFT GROUP.......................92 PTO CLUTCH GROUP..........................94 PTO SHAFT GROUP.............................96 SPIRAL BEVEL GEAR GROUP............98 FR. WH. DRIVING SHAFT GROUP....100 MAIN SHIFT FORK GROUP...............102 REAR DIFFERENTIAL GROUP..........104 SHIFT ROD GROUP...........................106 SHUTTLE FORK GROUP...................108

2009-07-06 오후 2:12:59


table of contents GROUP NO DK40-T315A DS4510-T350A DS4510-T370A DS4510-T380A DS4510-T400A DS4510-T410A DS4510-T560A DS4510-T465A DS4510-T595A DS4510-T600-1A D360-T610B D360-T620A D360-T630B D360-T650B CK30M-T660A D360-T660A D360-T670A DK40-T705A DS4510-T710A DS4510-T720A DS4510-T730A DS4510-T740A DS4510-T750A

M50-US-00-A.indd 4

GROUP NAME PAGE RANGE FORK GROUP.......................110 FRONT DRIVE FORK GROUP...........112 DIFF. LOCK FORK GROUP................114 BRAKE CASE GROUP........................116 BRAKE ROD GROUP..........................118 REAR AXLE GROUP...........................120 PROPELLER SHAFT GROUP............122 POWER STEERING UNIT GROUP....124 STEERING CYLINDER GROUP.........126 HYD. CYLINDER ASS`Y GROUP.......128 HYD. CYLINDER BODY GROUP........130 HYD. LIFT ARM GROUP.....................132 HYD. CONTROL SYSTEM GROUP 1....134 TOP LINK BRACKET GROUP.............136 HYD.CONTROL SYSTEM GROUP 2...138 MAIN DISTRIBUTOR VALVE GROUP..140 HYD. EXTERNAL VALVE 1 GROUP..................142 GEAR PUMP GROUP.........................144 PTO CLUTCH VALVE GROUP............146 HYDRAULIC BLACK GROUP.............148 HYDRAULIC FILTER GROUP.............150 HYDRAULIC TUBE GROUP...............152 INLET TUBE GROUP..........................154

GROUP NO LX480L-T010A DS4510-T020A DS4510-T030A DS4510-T100A DS4510-T325A DS4110-T430A DS4510-T550A EX45H-T596A DS4510-T770A DS4510-T780A D360-T790A DS4510-T805A LX480L-T810A DS4510-T820A DS4510-T830A LX480L-T840A DS4510-T915A DS4510-T935A DS4510-T995A DS4510-T1000A DS4510-T1015A DS4510-T1025A DS4510-T1035A

GROUP NAME PAGE AIR CLEANER GROUP.......................156 MUFFLER GROUP..............................158 RADIATOR GROUP.............................160 CLUTCH GROUP................................162 RANGE LEVER GROUP.....................164 FRONT AXLE FRAME GROUP...........166 FRONT AXLE BRACKET GROUP.......168 CYLINDER COVER GROUP...............170 POSITION CONTROL LEVER GROUP 172 3-POINT LINK SYSTEM 1GROUP......174 3-POINT CONNECTOR SYS. 2 GROUP... 176 DRAWBAR GROUP.............................178 BONNET 1 GROUP.............................180 BONNET 2 GROUP.............................182 FUEL TANK GROUP...........................184 FUEL FILTER GROUP.........................186 MAIN SHIFT LEVER GROUP..............188 FRONT WHEEL DRIVE LEVER GROUP 190 FENDER GROUP................................192 SEAT FLOOR GROUP........................194 SEAT GROUP......................................196 STEP GROUP.....................................198 HANDLE GROUP................................200

2009-07-06 오후 2:13:00


table of contents GROUP NO DS4510-T1065A DS4510-T2000A DS4510-T2005A DS4510-T2015A DS4510-T2035A DS4510-T2055A DS4510-T2060A DS4510-T515A DS4510-T555A DS4510-T565A DS4510-T575A CT230-T1050A DS4510-T2085A CK30M-T1020A CK30M-T1040A CK30-T1065A DS4510-T3000-1A

M50-US-00-A.indd 5

GROUP NAME PAGE ROPS GROUP.....................................202 CLUTCH PEDAL GROUP....................204 SHUTTLE LEVER GROUP..................206 BRAKE PEDAL GROUP......................208 FRAME GROUP..................................210 INSTRUMENT COVER GROUP.........212 THROTTLE GROUP............................214 BATTERY GROUP...............................216 ELECTRICAL SYSTEM 1 GROUP......218 ELECTRICAL SYSTEM 3 GROUP......220 LIGHT GROUP....................................222 WORKING LIGHT GROUP..................224 FRAME ELECTRONIC GROUP..........226 7 PIN SOCKET GROUP......................228 SUNSHADE GROUP...........................230 FRONT WEIGHT GROUP...................232 EXTERNAL HYDRAULIC VALVE GROUP......234

2009-07-06 오후 2:13:00


4A220LX-E010

CYLINDER BLOCK GROUP

24

M50-US-01.indd 24

2009-07-08 오전 9:33:40


REF NO JOB CODE

HOURS

DESCRIPTION

DS4510

DS4110

*

E010001

ENGINE ASSEMBLY, R & R

5.0

1

E010002

CYLINDER BLOCK ASSEMBLY

10.0

2

E010003

HOSE, WATER RETURN

0.5

3

E010004

OIL PUMP ASSEMBLY

5.0

4

E010005

GEAR, OIL PUMP DRIVING

5.0

5

E010006

OIL SWITCH

0.5

6

E010007

GUIDE

0.5

REMARK

25

M50-US-01.indd 25

2009-07-08 오전 9:33:40


4A220-E020

OIL PAN GROUP

26

M50-US-01.indd 26

2009-07-08 오전 9:33:41


REF NO JOB CODE

HOURS

DESCRIPTION

DS4510

DS4110

1

E020001

OIL PAN ASSEMBLY

1.5

2

E020002

GASKET, OIL PAN

1.5

3

E020003

FILTER 1, OIL

1.6

4

E020004

OIL GAUGE GUIDE PIPE

0.3

REMARK

27

M50-US-01.indd 27

2009-07-08 오전 9:33:41


4A220LW-E030

CYLINDER HEAD GROUP

28

M50-US-01.indd 28

2009-07-08 오전 9:33:42


REF NO JOB CODE

HOURS

DESCRIPTION

DS4510

DS4110

1

E030001

CYLINDER HEAD ASSEMBLY

3.0

2

E030002

COMBUSTION CHAMBER

2.5

3

E030003

GASKET, HEAD

2.5

REMARK

29

M50-US-01.indd 29

2009-07-08 오전 9:33:42


3B183-E040

GEAR CASE GROUP

30

M50-US-01.indd 30

2009-07-08 오전 9:33:43


REF NO JOB CODE

HOURS

DESCRIPTION

DS4510

DS4110

1

E040001

GEAR CASE ASSEMBLY

3.5

2

E040002

O-RING

3.5

3

E040003

O-RING

3.5

4

E040004

O-RING

3.5

5

E040005

GEAR CASE GASKET

3.5

REMARK

31

M50-US-01.indd 31

2009-07-08 오전 9:33:43


TD2200-E050

MAIN BEARING CASE GROUP

32

M50-US-01.indd 32

2009-07-08 오전 9:33:44


REF NO JOB CODE

HOURS

DESCRIPTION

DS4510

DS4110

1

E050001

MAIN BRG. CASE ASSEMBLY

9.0

2

E050002

COVER, MAIN BEARING CASE

5.0

REMARK

33

M50-US-01.indd 33

2009-07-08 오전 9:33:44


4A220A-E080

VALVE ROCKER ARM GROUP

34

M50-US-01.indd 34

2009-07-08 오전 9:33:51


REF NO JOB CODE

HOURS

DESCRIPTION

DS4510

DS4110

1

E080001

INLET VALVE

3.5

2

E080002

VALVE SPRING

3.0

3

E080003

ROCKERARM SHAFT ASSEMBLY

2.0

REMARK

35

M50-US-01.indd 35

2009-07-08 오전 9:33:51


4B243LX-E090

CYLINDER HEAD COVER GROUP

36

M50-US-01.indd 36

2009-07-08 오전 9:33:57


REF NO JOB CODE

HOURS

DESCRIPTION

DS4510

DS4110

1

E090001

CYLINDER HEAD COVER ASSEMBLY

0.5

2

E090002

AIR BREATHER

0.2

REMARK

37

M50-US-01.indd 37

2009-07-08 오전 9:33:57


4A220LX-E100

CAMSAFT GROUP

3,4(INCLUDING : E0300001)

38

M50-US-01.indd 38

2009-07-08 오전 9:33:58


REF NO JOB CODE

HOURS

DESCRIPTION

DS4510

DS4110

1

E100001

TAPPET

3.0

2

E100002

ROD, PUSH

2.0

3

E100003

CAMSHAFT ASSEMBLY

6.0

4

E100004

GEAR, CAMSHAFT

6.0

5

E100005

IDLE GEAR ASSEMBLY

4.0

6

E100006

SHAFT GEAR, IDLE

4.5

REMARK

39

M50-US-01.indd 39

2009-07-08 오전 9:33:58


4A200LW-E110

PISTON & CRANK SHAFT GROUP

40

M50-US-01.indd 40

2009-07-08 오전 9:33:59


REF NO JOB CODE

HOURS

DESCRIPTION

DS4510

DS4110

1

E110001

PISTON ASSEMBLY

6.0

2

E110002

RING PISTON ASSEMBLY

6.3

3

E110003

METAL, CRANK PIN

6.0

4

E110004

SHAFT CRANK ASSEMBLY

9.0

5

E110005

GEAR, CRANKSHAFT

5.0

6

E110006

METAL 1, CRANKSHAFT

9.0

REMARK

41

M50-US-01.indd 41

2009-07-08 오전 9:33:59


4A200B-E120

FLYWHEEL GROUP

42

M50-US-01.indd 42

2009-07-08 오전 9:33:59


REF NO JOB CODE

HOURS

DESCRIPTION

DS4510

DS4110

1

E120001

FLYWHEEL ASSEMBLY

4.0

2

E120002

GEAR, RING

4.5

3

E120003

HOUSING, FLYWHEEL

4.5

4

E120004

STARTER MOTOR ASSEMBLY

1.0

5

E120005

GASKET

1.0

REMARK

43

M50-US-01.indd 43

2009-07-08 오전 9:34:00


4A220-E130

NOZZLE HOLDER GROUP

44

M50-US-01.indd 44

2009-07-08 오전 9:34:09


REF NO JOB CODE

HOURS

DESCRIPTION

DS4510

DS4110

1

E130001

HOLDER, NOZZLE ASSEMBLY

1.5

2

E130002

INJECTION PIPE

0.5

3

E130003

GLOW PLUG

0.5

4

E130004

HOSE, OVER FLOW

0.7

REMARK

45

M50-US-01.indd 45

2009-07-08 오전 9:34:09


4A220LX-E140

FUEL CAMSHAFT GROUP

1 (INCLUDING: E1400002, E1700001, N7050003)

46

M50-US-01.indd 46

2009-07-08 오전 9:34:10


REF NO JOB CODE

HOURS

DESCRIPTION

DS4510

DS4110

1

E140001

CAMSHAFT, FUEL INJECTION

5.0

2

E140002

INJECTION PUMP ASSEMBLY

2.0

3

E140003

FUEL PUMP ASSEMBLY

0.5

REMARK

47

M50-US-01.indd 47

2009-07-08 오전 9:34:10


Thank you very much for your reading. Please click here and go back to our website. Then, you can download the complete manual instantly. No waiting. Have questions. Please write to me. All the problems will be answered within 12 hours. aservicemanuapdf@yahoo.com

Kioti Daedong DS4110 Tractor Parts Catalogue Manual  
Kioti Daedong DS4110 Tractor Parts Catalogue Manual  
Advertisement